Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

Conflicts:
	net/ipv4/arp.c

The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.

Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/arm/gic-v3.txt

@@ -57,6 +57,8 @@ used to route Message Signalled Interrupts (MSI) to the CPUs.
 These nodes must have the following properties:
 - compatible : Should at least contain  "arm,gic-v3-its".
 - msi-controller : Boolean property. Identifies the node as an MSI controller
+- #msi-cells: Must be <1>. The single msi-cell is the DeviceID of the device
+  which will generate the MSI.
 - reg: Specifies the base physical address and size of the ITS
   registers.
 
@@ -83,6 +85,7 @@ Examples:
 		gic-its@2c200000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c200000 0 0x200000>;
 		};
 	};
@@ -107,12 +110,14 @@ Examples:
 		gic-its@2c200000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c200000 0 0x200000>;
 		};
 
 		gic-its@2c400000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c400000 0 0x200000>;
 		};
 	};

Documentation/devicetree/bindings/arm/idle-states.txt

@@ -497,7 +497,7 @@ cpus {
 	};
 
 	idle-states {
-		entry-method = "arm,psci";
+		entry-method = "psci";
 
 		CPU_RETENTION_0_0: cpu-retention-0-0 {
 			compatible = "arm,idle-state";

Documentation/devicetree/bindings/gpio/gpio.txt

@@ -16,7 +16,9 @@ properties, each containing a 'gpio-list':
 GPIO properties should be named "[<name>-]gpios", with <name> being the purpose
 of this GPIO for the device. While a non-existent <name> is considered valid
 for compatibility reasons (resolving to the "gpios" property), it is not allowed
-for new bindings.
+for new bindings. Also, GPIO properties named "[<name>-]gpio" are valid and old
+bindings use it, but are only supported for compatibility reasons and should not
+be used for newer bindings since it has been deprecated.
 
 GPIO properties can contain one or more GPIO phandles, but only in exceptional
 cases should they contain more than one. If your device uses several GPIOs with

Documentation/devicetree/bindings/iio/accel/bma180.txt

@@ -1,10 +1,11 @@
-* Bosch BMA180 triaxial acceleration sensor
+* Bosch BMA180 / BMA250 triaxial acceleration sensor
 
 http://omapworld.com/BMA180_111_1002839.pdf
+http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/bst-bma250-ds002-05.pdf
 
 Required properties:
 
-  - compatible : should be "bosch,bma180"
+  - compatible : should be "bosch,bma180" or "bosch,bma250"
   - reg : the I2C address of the sensor
 
 Optional properties:
@@ -13,6 +14,9 @@ Optional properties:
 
   - interrupts : interrupt mapping for GPIO IRQ, it should by configured with
 		flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING
+		For the bma250 the first interrupt listed must be the one
+		connected to the INT1 pin, the second (optional) interrupt
+		listed must be the one connected to the INT2 pin.
 
 Example:
 

Documentation/devicetree/bindings/input/touchscreen/colibri-vf50-ts.txt

@@ -0,0 +1,36 @@
+* Toradex Colibri VF50 Touchscreen driver
+
+Required Properties:
+- compatible must be toradex,vf50-touchscreen
+- io-channels: adc channels being used by the Colibri VF50 module
+- xp-gpios: FET gate driver for input of X+
+- xm-gpios: FET gate driver for input of X-
+- yp-gpios: FET gate driver for input of Y+
+- ym-gpios: FET gate driver for input of Y-
+- interrupt-parent: phandle for the interrupt controller
+- interrupts: pen irq interrupt for touch detection
+- pinctrl-names: "idle", "default", "gpios"
+- pinctrl-0: pinctrl node for pen/touch detection state pinmux
+- pinctrl-1: pinctrl node for X/Y and pressure measurement (ADC) state pinmux
+- pinctrl-2: pinctrl node for gpios functioning as FET gate drivers
+- vf50-ts-min-pressure: pressure level at which to stop measuring X/Y values
+
+Example:
+
+	touchctrl: vf50_touchctrl {
+		compatible = "toradex,vf50-touchscreen";
+		io-channels = <&adc1 0>,<&adc0 0>,
+				<&adc0 1>,<&adc1 2>;
+		xp-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+		xm-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+		yp-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		ym-gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "idle","default","gpios";
+		pinctrl-0 = <&pinctrl_touchctrl_idle>;
+		pinctrl-1 = <&pinctrl_touchctrl_default>;
+		pinctrl-2 = <&pinctrl_touchctrl_gpios>;
+		vf50-ts-min-pressure = <200>;
+		status = "disabled";
+	};

Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt

@@ -0,0 +1,36 @@
+* Freescale i.MX6UL Touch Controller
+
+Required properties:
+- compatible: must be "fsl,imx6ul-tsc".
+- reg: this touch controller address and the ADC2 address.
+- interrupts: the interrupt of this touch controller and ADC2.
+- clocks: the root clock of touch controller and ADC2.
+- clock-names; must be "tsc" and "adc".
+- xnur-gpio: the X- gpio this controller connect to.
+  This xnur-gpio returns to low once the finger leave the touch screen (The
+  last touch event the touch controller capture).
+
+Optional properties:
+- measure-delay-time: the value of measure delay time.
+  Before X-axis or Y-axis measurement, the screen need some time before
+  even potential distribution ready.
+  This value depends on the touch screen.
+- pre-charge-time: the touch screen need some time to precharge.
+  This value depends on the touch screen.
+
+Example:
+	tsc: tsc@02040000 {
+		compatible = "fsl,imx6ul-tsc";
+		reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
+		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clks IMX6UL_CLK_IPG>,
+			 <&clks IMX6UL_CLK_ADC2>;
+		clock-names = "tsc", "adc";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tsc>;
+		xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+		measure-delay-time = <0xfff>;
+		pre-charge-time = <0xffff>;
+		status = "okay";
+	};

Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt

@@ -7,7 +7,8 @@ OHCI and EHCI controllers.
 
 Required properties:
 - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC;
-	      "renesas,pci-r8a7791" for the R8A7791 SoC.
+	      "renesas,pci-r8a7791" for the R8A7791 SoC;
+	      "renesas,pci-r8a7794" for the R8A7794 SoC.
 - reg:	A list of physical regions to access the device: the first is
 	the operational registers for the OHCI/EHCI controllers and the
 	second is for the bridge configuration and control registers.

Documentation/devicetree/bindings/regulator/pbias-regulator.txt

@@ -2,7 +2,12 @@ PBIAS internal regulator for SD card dual voltage i/o pads on OMAP SoCs.
 
 Required properties:
 - compatible:
-  - "ti,pbias-omap" for OMAP2, OMAP3, OMAP4, OMAP5, DRA7.
+  - should be "ti,pbias-dra7" for DRA7
+  - should be "ti,pbias-omap2" for OMAP2
+  - should be "ti,pbias-omap3" for OMAP3
+  - should be "ti,pbias-omap4" for OMAP4
+  - should be "ti,pbias-omap5" for OMAP5
+  - "ti,pbias-omap" is deprecated
 - reg: pbias register offset from syscon base and size of pbias register.
 - syscon : phandle of the system control module
 - regulator-name : should be

Documentation/devicetree/bindings/spi/spi-mt65xx.txt

@@ -15,17 +15,18 @@ Required properties:
 - interrupts: Should contain spi interrupt
 
 - clocks: phandles to input clocks.
-  The first should be <&topckgen CLK_TOP_SPI_SEL>.
-  The second should be one of the following.
+  The first should be one of the following. It's PLL.
    -  <&clk26m>: specify parent clock 26MHZ.
    -  <&topckgen CLK_TOP_SYSPLL3_D2>: specify parent clock 109MHZ.
 				      It's the default one.
    -  <&topckgen CLK_TOP_SYSPLL4_D2>: specify parent clock 78MHZ.
    -  <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ.
    -  <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ.
+  The second should be <&topckgen CLK_TOP_SPI_SEL>. It's clock mux.
+  The third is <&pericfg CLK_PERI_SPI0>. It's clock gate.
 
-- clock-names: shall be "spi-clk" for the controller clock, and
-  "parent-clk" for the parent clock.
+- clock-names: shall be "parent-clk" for the parent clock, "sel-clk" for the
+  muxes clock, and "spi-clk" for the clock gate.
 
 Optional properties:
 - mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi
@@ -44,8 +45,11 @@ spi: spi@1100a000 {
 	#size-cells = <0>;
 	reg = <0 0x1100a000 0 0x1000>;
 	interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>;
-	clocks = <&topckgen CLK_TOP_SPI_SEL>, <&topckgen CLK_TOP_SYSPLL3_D2>;
-	clock-names = "spi-clk", "parent-clk";
+	clocks = <&topckgen CLK_TOP_SYSPLL3_D2>,
+		 <&topckgen CLK_TOP_SPI_SEL>,
+		 <&pericfg CLK_PERI_SPI0>;
+	clock-names = "parent-clk", "sel-clk", "spi-clk";
+
 	mediatek,pad-select = <0>;
 	status = "disabled";
 };

Documentation/devicetree/bindings/thermal/thermal.txt

@@ -55,19 +55,11 @@ of heat dissipation). For example a fan's cooling states correspond to
 the different fan speeds possible. Cooling states are referred to by
 single unsigned integers, where larger numbers mean greater heat
 dissipation. The precise set of cooling states associated with a device
-(as referred to be the cooling-min-state and cooling-max-state
+(as referred to by the cooling-min-level and cooling-max-level
 properties) should be defined in a particular device's binding.
 For more examples of cooling devices, refer to the example sections below.
 
 Required properties:
-- cooling-min-state:	An integer indicating the smallest
-  Type: unsigned	cooling state accepted. Typically 0.
-  Size: one cell
-
-- cooling-max-state:	An integer indicating the largest
-  Type: unsigned	cooling state accepted.
-  Size: one cell
-
 - #cooling-cells:	Used to provide cooling device specific information
   Type: unsigned	while referring to it. Must be at least 2, in order
   Size: one cell      	to specify minimum and maximum cooling state used
@@ -77,6 +69,15 @@ Required properties:
 			See Cooling device maps section below for more details
 			on how consumers refer to cooling devices.
 
+Optional properties:
+- cooling-min-level:	An integer indicating the smallest
+  Type: unsigned	cooling state accepted. Typically 0.
+  Size: one cell
+
+- cooling-max-level:	An integer indicating the largest
+  Type: unsigned	cooling state accepted.
+  Size: one cell
+
 * Trip points
 
 The trip node is a node to describe a point in the temperature domain
@@ -225,8 +226,8 @@ cpus {
 			396000  950000
 			198000  850000
 		>;
-		cooling-min-state = <0>;
-		cooling-max-state = <3>;
+		cooling-min-level = <0>;
+		cooling-max-level = <3>;
 		#cooling-cells = <2>; /* min followed by max */
 	};
 	...
@@ -240,8 +241,8 @@ cpus {
 	 */
 	fan0: fan@0x48 {
 		...
-		cooling-min-state = <0>;
-		cooling-max-state = <9>;
+		cooling-min-level = <0>;
+		cooling-max-level = <9>;
 		#cooling-cells = <2>; /* min followed by max */
 	};
 };

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -203,6 +203,7 @@ sitronix	Sitronix Technology Corporation
 skyworks	Skyworks Solutions, Inc.
 smsc	Standard Microsystems Corporation
 snps	Synopsys, Inc.
+socionext	Socionext Inc.
 solidrun	SolidRun
 solomon        Solomon Systech Limited
 sony	Sony Corporation

Documentation/devicetree/bindings/watchdog/atmel-sama5d4-wdt.txt

@@ -0,0 +1,35 @@
+* Atmel SAMA5D4 Watchdog Timer (WDT) Controller
+
+Required properties:
+- compatible: "atmel,sama5d4-wdt"
+- reg: base physical address and length of memory mapped region.
+
+Optional properties:
+- timeout-sec: watchdog timeout value (in seconds).
+- interrupts: interrupt number to the CPU.
+- atmel,watchdog-type: should be "hardware" or "software".
+	"hardware": enable watchdog fault reset. A watchdog fault triggers
+		    watchdog reset.
+	"software": enable watchdog fault interrupt. A watchdog fault asserts
+		    watchdog interrupt.
+- atmel,idle-halt: present if you want to stop the watchdog when the CPU is
+		   in idle state.
+	CAUTION: This property should be used with care, it actually makes the
+	watchdog not counting when the CPU is in idle state, therefore the
+	watchdog reset time depends on mean CPU usage and will not reset at all
+	if the CPU stop working while it is in idle state, which is probably
+	not what you want.
+- atmel,dbg-halt: present if you want to stop the watchdog when the CPU is
+		  in debug state.
+
+Example:
+	watchdog@fc068640 {
+		compatible = "atmel,sama5d4-wdt";
+		reg = <0xfc068640 0x10>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH 5>;
+		timeout-sec = <10>;
+		atmel,watchdog-type = "hardware";
+		atmel,dbg-halt;
+		atmel,idle-halt;
+		status = "okay";
+	};

Documentation/devicetree/bindings/watchdog/lpc18xx-wdt.txt

@@ -0,0 +1,19 @@
+* NXP LPC18xx Watchdog Timer (WDT)
+
+Required properties:
+- compatible: Should be "nxp,lpc1850-wwdt"
+- reg: Should contain WDT registers location and length
+- clocks: Must contain an entry for each entry in clock-names.
+- clock-names: Should contain "wdtclk" and "reg"; the watchdog counter
+               clock and register interface clock respectively.
+- interrupts: Should contain WDT interrupt
+
+Examples:
+
+watchdog@40080000 {
+	compatible = "nxp,lpc1850-wwdt";
+	reg = <0x40080000 0x24>;
+	clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_WWDT>;
+	clock-names = "wdtclk", "reg";
+	interrupts = <49>;
+};

Documentation/gpio/board.txt

@@ -21,8 +21,8 @@ exact way to do it depends on the GPIO controller providing the GPIOs, see the
 device tree bindings for your controller.
 
 GPIOs mappings are defined in the consumer device's node, in a property named
-<function>-gpios, where <function> is the function the driver will request
-through gpiod_get(). For example:
+either <function>-gpios or <function>-gpio, where <function> is the function
+the driver will request through gpiod_get(). For example:
 
 	foo_device {
 		compatible = "acme,foo";
@@ -31,7 +31,7 @@ through gpiod_get(). For example:
 			    <&gpio 16 GPIO_ACTIVE_HIGH>, /* green */
 			    <&gpio 17 GPIO_ACTIVE_HIGH>; /* blue */
 
-		power-gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+		power-gpio = <&gpio 1 GPIO_ACTIVE_LOW>;
 	};
 
 This property will make GPIOs 15, 16 and 17 available to the driver under the
@@ -39,15 +39,24 @@ This property will make GPIOs 15, 16 and 17 available to the driver under the
 
 	struct gpio_desc *red, *green, *blue, *power;
 
-	red = gpiod_get_index(dev, "led", 0);
-	green = gpiod_get_index(dev, "led", 1);
-	blue = gpiod_get_index(dev, "led", 2);
+	red = gpiod_get_index(dev, "led", 0, GPIOD_OUT_HIGH);
+	green = gpiod_get_index(dev, "led", 1, GPIOD_OUT_HIGH);
+	blue = gpiod_get_index(dev, "led", 2, GPIOD_OUT_HIGH);
 
-	power = gpiod_get(dev, "power");
+	power = gpiod_get(dev, "power", GPIOD_OUT_HIGH);
 
 The led GPIOs will be active-high, while the power GPIO will be active-low (i.e.
 gpiod_is_active_low(power) will be true).
 
+The second parameter of the gpiod_get() functions, the con_id string, has to be
+the <function>-prefix of the GPIO suffixes ("gpios" or "gpio", automatically
+looked up by the gpiod functions internally) used in the device tree. With above
+"led-gpios" example, use the prefix without the "-" as con_id parameter: "led".
+
+Internally, the GPIO subsystem prefixes the GPIO suffix ("gpios" or "gpio")
+with the string passed in con_id to get the resulting string
+(snprintf(... "%s-%s", con_id, gpio_suffixes[]).
+
 ACPI
 ----
 ACPI also supports function names for GPIOs in a similar fashion to DT.
@@ -142,13 +151,14 @@ The driver controlling "foo.0" will then be able to obtain its GPIOs as follows:
 
 	struct gpio_desc *red, *green, *blue, *power;
 
-	red = gpiod_get_index(dev, "led", 0);
-	green = gpiod_get_index(dev, "led", 1);
-	blue = gpiod_get_index(dev, "led", 2);
+	red = gpiod_get_index(dev, "led", 0, GPIOD_OUT_HIGH);
+	green = gpiod_get_index(dev, "led", 1, GPIOD_OUT_HIGH);
+	blue = gpiod_get_index(dev, "led", 2, GPIOD_OUT_HIGH);
 
-	power = gpiod_get(dev, "power");
-	gpiod_direction_output(power, 1);
+	power = gpiod_get(dev, "power", GPIOD_OUT_HIGH);
 
-Since the "power" GPIO is mapped as active-low, its actual signal will be 0
-after this code. Contrary to the legacy integer GPIO interface, the active-low
-property is handled during mapping and is thus transparent to GPIO consumers.
+Since the "led" GPIOs are mapped as active-high, this example will switch their
+signals to 1, i.e. enabling the LEDs. And for the "power" GPIO, which is mapped
+as active-low, its actual signal will be 0 after this code. Contrary to the legacy
+integer GPIO interface, the active-low property is handled during mapping and is
+thus transparent to GPIO consumers.

Documentation/gpio/consumer.txt

@@ -39,6 +39,9 @@ device that displays digits), an additional index argument can be specified:
 					  const char *con_id, unsigned int idx,
 					  enum gpiod_flags flags)
 
+For a more detailed description of the con_id parameter in the DeviceTree case
+see Documentation/gpio/board.txt
+
 The flags parameter is used to optionally specify a direction and initial value
 for the GPIO. Values can be:
 

Documentation/hwmon/nct6775

@@ -32,6 +32,10 @@ Supported chips:
     Prefix: 'nct6792'
     Addresses scanned: ISA address retrieved from Super I/O registers
     Datasheet: Available from Nuvoton upon request
+  * Nuvoton NCT6793D
+    Prefix: 'nct6793'
+    Addresses scanned: ISA address retrieved from Super I/O registers
+    Datasheet: Available from Nuvoton upon request
 
 Authors:
         Guenter Roeck <linux@roeck-us.net>

Documentation/networking/vrf.txt

@@ -0,0 +1,96 @@
+Virtual Routing and Forwarding (VRF)
+====================================
+The VRF device combined with ip rules provides the ability to create virtual
+routing and forwarding domains (aka VRFs, VRF-lite to be specific) in the
+Linux network stack. One use case is the multi-tenancy problem where each
+tenant has their own unique routing tables and in the very least need
+different default gateways.
+
+Processes can be "VRF aware" by binding a socket to the VRF device. Packets
+through the socket then use the routing table associated with the VRF
+device. An important feature of the VRF device implementation is that it
+impacts only Layer 3 and above so L2 tools (e.g., LLDP) are not affected
+(ie., they do not need to be run in each VRF). The design also allows
+the use of higher priority ip rules (Policy Based Routing, PBR) to take
+precedence over the VRF device rules directing specific traffic as desired.
+
+In addition, VRF devices allow VRFs to be nested within namespaces. For
+example network namespaces provide separation of network interfaces at L1
+(Layer 1 separation), VLANs on the interfaces within a namespace provide
+L2 separation and then VRF devices provide L3 separation.
+
+Design
+------
+A VRF device is created with an associated route table. Network interfaces
+are then enslaved to a VRF device:
+
+         +-----------------------------+
+         |           vrf-blue          |  ===> route table 10
+         +-----------------------------+
+            |        |            |
+         +------+ +------+     +-------------+
+         | eth1 | | eth2 | ... |    bond1    |
+         +------+ +------+     +-------------+
+                                  |       |
+                              +------+ +------+
+                              | eth8 | | eth9 |
+                              +------+ +------+
+
+Packets received on an enslaved device and are switched to the VRF device
+using an rx_handler which gives the impression that packets flow through
+the VRF device. Similarly on egress routing rules are used to send packets
+to the VRF device driver before getting sent out the actual interface. This
+allows tcpdump on a VRF device to capture all packets into and out of the
+VRF as a whole.[1] Similiarly, netfilter [2] and tc rules can be applied
+using the VRF device to specify rules that apply to the VRF domain as a whole.
+
+[1] Packets in the forwarded state do not flow through the device, so those
+    packets are not seen by tcpdump. Will revisit this limitation in a
+    future release.
+
+[2] Iptables on ingress is limited to NF_INET_PRE_ROUTING only with skb->dev
+    set to real ingress device and egress is limited to NF_INET_POST_ROUTING.
+    Will revisit this limitation in a future release.
+
+
+Setup
+-----
+1. VRF device is created with an association to a FIB table.
+   e.g, ip link add vrf-blue type vrf table 10
+        ip link set dev vrf-blue up
+
+2. Rules are added that send lookups to the associated FIB table when the
+   iif or oif is the VRF device. e.g.,
+       ip ru add oif vrf-blue table 10
+       ip ru add iif vrf-blue table 10
+
+   Set the default route for the table (and hence default route for the VRF).
+   e.g, ip route add table 10 prohibit default
+
+3. Enslave L3 interfaces to a VRF device.
+   e.g,  ip link set dev eth1 master vrf-blue
+
+   Local and connected routes for enslaved devices are automatically moved to
+   the table associated with VRF device. Any additional routes depending on
+   the enslaved device will need to be reinserted following the enslavement.
+
+4. Additional VRF routes are added to associated table.
+   e.g., ip route add table 10 ...
+
+
+Applications
+------------
+Applications that are to work within a VRF need to bind their socket to the
+VRF device:
+
+    setsockopt(sd, SOL_SOCKET, SO_BINDTODEVICE, dev, strlen(dev)+1);
+
+or to specify the output device using cmsg and IP_PKTINFO.
+
+
+Limitations
+-----------
+VRF device currently only works for IPv4. Support for IPv6 is under development.
+
+Index of original ingress interface is not available via cmsg. Will address
+soon.

Documentation/static-keys.txt

@@ -15,8 +15,8 @@ The updated API replacements are:
 
 DEFINE_STATIC_KEY_TRUE(key);
 DEFINE_STATIC_KEY_FALSE(key);
-static_key_likely()
-statick_key_unlikely()
+static_branch_likely()
+static_branch_unlikely()
 
 0) Abstract
 

Documentation/sysctl/net.txt

@@ -54,13 +54,15 @@ default_qdisc
 --------------
 
 The default queuing discipline to use for network devices. This allows
-overriding the default queue discipline of pfifo_fast with an
-alternative. Since the default queuing discipline is created with the
-no additional parameters so is best suited to queuing disciplines that
-work well without configuration like stochastic fair queue (sfq),
-CoDel (codel) or fair queue CoDel (fq_codel). Don't use queuing disciplines
-like Hierarchical Token Bucket or Deficit Round Robin which require setting
-up classes and bandwidths.
+overriding the default of pfifo_fast with an alternative. Since the default
+queuing discipline is created without additional parameters so is best suited
+to queuing disciplines that work well without configuration like stochastic
+fair queue (sfq), CoDel (codel) or fair queue CoDel (fq_codel). Don't use
+queuing disciplines like Hierarchical Token Bucket or Deficit Round Robin
+which require setting up classes and bandwidths. Note that physical multiqueue
+interfaces still use mq as root qdisc, which in turn uses this default for its
+leaves. Virtual devices (like e.g. lo or veth) ignore this setting and instead
+default to noqueue.
 Default: pfifo_fast
 
 busy_read

Documentation/thermal/power_allocator.txt

@@ -4,7 +4,7 @@ Power allocator governor tunables
 Trip points
 -----------
 
-The governor requires the following two passive trip points:
+The governor works optimally with the following two passive trip points:
 
 1.  "switch on" trip point: temperature above which the governor
     control loop starts operating.  This is the first passive trip

Documentation/thermal/sysfs-api.txt

@@ -180,6 +180,7 @@ Thermal zone device sys I/F, created once it's registered:
     |---temp:			Current temperature
     |---mode:			Working mode of the thermal zone
     |---policy:			Thermal governor used for this zone
+    |---available_policies:	Available thermal governors for this zone
     |---trip_point_[0-*]_temp:	Trip point temperature
     |---trip_point_[0-*]_type:	Trip point type
     |---trip_point_[0-*]_hyst:	Hysteresis value for this trip point
@@ -256,6 +257,10 @@ policy
 	One of the various thermal governors used for a particular zone.
 	RW, Required
 
+available_policies
+	Available thermal governors which can be used for a particular zone.
+	RO, Required
+
 trip_point_[0-*]_temp
 	The temperature above which trip point will be fired.
 	Unit: millidegree Celsius
@@ -417,6 +422,7 @@ method, the sys I/F structure will be built like this:
     |---temp:			37000
     |---mode:			enabled
     |---policy:			step_wise
+    |---available_policies:	step_wise fair_share
     |---trip_point_0_temp:	100000
     |---trip_point_0_type:	critical
     |---trip_point_1_temp:	80000

Documentation/watchdog/src/watchdog-test.c

@@ -41,6 +41,7 @@ static void term(int sig)
 int main(int argc, char *argv[])
 {
     int flags;
+    unsigned int ping_rate = 1;
 
     fd = open("/dev/watchdog", O_WRONLY);
 
@@ -63,22 +64,33 @@ int main(int argc, char *argv[])
 	    fprintf(stderr, "Watchdog card enabled.\n");
 	    fflush(stderr);
 	    goto end;
+	} else if (!strncasecmp(argv[1], "-t", 2) && argv[2]) {
+	    flags = atoi(argv[2]);
+	    ioctl(fd, WDIOC_SETTIMEOUT, &flags);
+	    fprintf(stderr, "Watchdog timeout set to %u seconds.\n", flags);
+	    fflush(stderr);
+	    goto end;
+	} else if (!strncasecmp(argv[1], "-p", 2) && argv[2]) {
+	    ping_rate = strtoul(argv[2], NULL, 0);
+	    fprintf(stderr, "Watchdog ping rate set to %u seconds.\n", ping_rate);
+	    fflush(stderr);
 	} else {
-	    fprintf(stderr, "-d to disable, -e to enable.\n");
+	    fprintf(stderr, "-d to disable, -e to enable, -t <n> to set " \
+		"the timeout,\n-p <n> to set the ping rate, and \n");
 	    fprintf(stderr, "run by itself to tick the card.\n");
 	    fflush(stderr);
 	    goto end;
 	}
-    } else {
-	fprintf(stderr, "Watchdog Ticking Away!\n");
-	fflush(stderr);
     }
 
+    fprintf(stderr, "Watchdog Ticking Away!\n");
+    fflush(stderr);
+
     signal(SIGINT, term);
 
     while(1) {
 	keep_alive();
-	sleep(1);
+	sleep(ping_rate);
     }
 end:
     close(fd);

MAINTAINERS

@@ -808,6 +808,13 @@ S:	Maintained
 F:	drivers/video/fbdev/arcfb.c
 F:	drivers/video/fbdev/core/fb_defio.c
 
+ARCNET NETWORK LAYER
+M:	Michael Grzeschik <m.grzeschik@pengutronix.de>
+L:	netdev@vger.kernel.org
+S:	Maintained
+F:	drivers/net/arcnet/
+F:	include/uapi/linux/if_arcnet.h
+
 ARM MFM AND FLOPPY DRIVERS
 M:	Ian Molton <spyro@f2s.com>
 S:	Maintained
@@ -6452,11 +6459,11 @@ F:	drivers/hwmon/ltc4261.c
 LTP (Linux Test Project)
 M:	Mike Frysinger <vapier@gentoo.org>
 M:	Cyril Hrubis <chrubis@suse.cz>
-M:	Wanlong Gao <gaowanlong@cn.fujitsu.com>
+M:	Wanlong Gao <wanlong.gao@gmail.com>
 M:	Jan Stancek <jstancek@redhat.com>
 M:	Stanislav Kholmanskikh <stanislav.kholmanskikh@oracle.com>
 M:	Alexey Kodanev <alexey.kodanev@oracle.com>
-L:	ltp-list@lists.sourceforge.net (subscribers-only)
+L:	ltp@lists.linux.it (subscribers-only)
 W:	http://linux-test-project.github.io/
 T:	git git://github.com/linux-test-project/ltp.git
 S:	Maintained
@@ -6789,6 +6796,14 @@ W:	http://www.mellanox.com
 Q:	http://patchwork.ozlabs.org/project/netdev/list/
 F:	drivers/net/ethernet/mellanox/mlxsw/
 
+MEMBARRIER SUPPORT
+M:	Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
+M:	"Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
+L:	linux-kernel@vger.kernel.org
+S:	Supported
+F:	kernel/membarrier.c
+F:	include/uapi/linux/membarrier.h
+
 MEMORY MANAGEMENT
 L:	linux-mm@kvack.org
 W:	http://www.linux-mm.org
@@ -7395,6 +7410,7 @@ NTB DRIVER CORE
 M:	Jon Mason <jdmason@kudzu.us>
 M:	Dave Jiang <dave.jiang@intel.com>
 M:	Allen Hubbe <Allen.Hubbe@emc.com>
+L:	linux-ntb@googlegroups.com
 S:	Supported
 W:	https://github.com/jonmason/ntb/wiki
 T:	git git://github.com/jonmason/ntb.git
@@ -7406,6 +7422,7 @@ F:	include/linux/ntb_transport.h
 NTB INTEL DRIVER
 M:	Jon Mason <jdmason@kudzu.us>
 M:	Dave Jiang <dave.jiang@intel.com>
+L:	linux-ntb@googlegroups.com
 S:	Supported
 W:	https://github.com/jonmason/ntb/wiki
 T:	git git://github.com/jonmason/ntb.git
@@ -8489,7 +8506,6 @@ F:	Documentation/networking/LICENSE.qla3xxx
 F:	drivers/net/ethernet/qlogic/qla3xxx.*
 
 QLOGIC QLCNIC (1/10)Gb ETHERNET DRIVER
-M:	Shahed Shaikh <shahed.shaikh@qlogic.com>
 M:	Dept-GELinuxNICDev@qlogic.com
 L:	netdev@vger.kernel.org
 S:	Supported
@@ -10327,6 +10343,16 @@ F:	include/uapi/linux/thermal.h
 F:	include/linux/cpu_cooling.h
 F:	Documentation/devicetree/bindings/thermal/
 
+THERMAL/CPU_COOLING
+M:	Amit Daniel Kachhap <amit.kachhap@gmail.com>
+M:	Viresh Kumar <viresh.kumar@linaro.org>
+M:	Javi Merino <javi.merino@arm.com>
+L:	linux-pm@vger.kernel.org
+S:	Supported
+F:	Documentation/thermal/cpu-cooling-api.txt
+F:	drivers/thermal/cpu_cooling.c
+F:	include/linux/cpu_cooling.h
+
 THINGM BLINK(1) USB RGB LED DRIVER
 M:	Vivien Didelot <vivien.didelot@savoirfairelinux.com>
 S:	Maintained
@@ -11228,7 +11254,6 @@ VOLTAGE AND CURRENT REGULATOR FRAMEWORK
 M:	Liam Girdwood <lgirdwood@gmail.com>
 M:	Mark Brown <broonie@kernel.org>
 L:	linux-kernel@vger.kernel.org
-W:	http://opensource.wolfsonmicro.com/node/15
 W:	http://www.slimlogic.co.uk/?p=48
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git
 S:	Supported
@@ -11242,6 +11267,7 @@ L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/vrf.c
 F:	include/net/vrf.h
+F:	Documentation/networking/vrf.txt
 
 VT1211 HARDWARE MONITOR DRIVER
 M:	Juerg Haefliger <juergh@gmail.com>
@@ -11357,17 +11383,15 @@ WM97XX TOUCHSCREEN DRIVERS
 M:	Mark Brown <broonie@kernel.org>
 M:	Liam Girdwood <lrg@slimlogic.co.uk>
 L:	linux-input@vger.kernel.org
-T:	git git://opensource.wolfsonmicro.com/linux-2.6-touch
-W:	http://opensource.wolfsonmicro.com/node/7
+W:	https://github.com/CirrusLogic/linux-drivers/wiki
 S:	Supported
 F:	drivers/input/touchscreen/*wm97*
 F:	include/linux/wm97xx.h
 
 WOLFSON MICROELECTRONICS DRIVERS
 L:	patches@opensource.wolfsonmicro.com
-T:	git git://opensource.wolfsonmicro.com/linux-2.6-asoc
-T:	git git://opensource.wolfsonmicro.com/linux-2.6-audioplus
-W:	http://opensource.wolfsonmicro.com/content/linux-drivers-wolfson-devices
+T:	git https://github.com/CirrusLogic/linux-drivers.git
+W:	https://github.com/CirrusLogic/linux-drivers/wiki
 S:	Supported
 F:	Documentation/hwmon/wm83??
 F:	arch/arm/mach-s3c64xx/mach-crag6410*

Makefile

@@ -1,7 +1,7 @@
 VERSION = 4
-PATCHLEVEL = 2
+PATCHLEVEL = 3
 SUBLEVEL = 0
-EXTRAVERSION =
+EXTRAVERSION = -rc2
 NAME = Hurr durr I'ma sheep
 
 # *DOCUMENTATION*

arch/alpha/include/asm/io.h

@@ -297,7 +297,9 @@ static inline void __iomem * ioremap_nocache(unsigned long offset,
 					     unsigned long size)
 {
 	return ioremap(offset, size);
-} 
+}
+
+#define ioremap_uc ioremap_nocache
 
 static inline void iounmap(volatile void __iomem *addr)
 {

arch/alpha/kernel/irq.c

@@ -117,6 +117,6 @@ handle_irq(int irq)
 	}
 
 	irq_enter();
-	generic_handle_irq_desc(irq, desc);
+	generic_handle_irq_desc(desc);
 	irq_exit();
 }

arch/alpha/kernel/pci.c

@@ -242,7 +242,12 @@ pci_restore_srm_config(void)
 
 void pcibios_fixup_bus(struct pci_bus *bus)
 {
-	struct pci_dev *dev;
+	struct pci_dev *dev = bus->self;
+
+	if (pci_has_flag(PCI_PROBE_ONLY) && dev &&
+	    (dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) {
+		pci_read_bridge_bases(bus);
+	}
 
 	list_for_each_entry(dev, &bus->devices, bus_list) {
 		pdev_save_srm_config(dev);

arch/alpha/lib/udelay.c

@@ -30,6 +30,7 @@ __delay(int loops)
 		"	bgt %0,1b"
 		: "=&r" (tmp), "=r" (loops) : "1"(loops));
 }
+EXPORT_SYMBOL(__delay);
 
 #ifdef CONFIG_SMP
 #define LPJ	 cpu_data[smp_processor_id()].loops_per_jiffy

arch/arc/kernel/mcip.c

@@ -252,7 +252,7 @@ static struct irq_chip idu_irq_chip = {
 
 static int idu_first_irq;
 
-static void idu_cascade_isr(unsigned int __core_irq, struct irq_desc *desc)
+static void idu_cascade_isr(struct irq_desc *desc)
 {
 	struct irq_domain *domain = irq_desc_get_handler_data(desc);
 	unsigned int core_irq = irq_desc_get_irq(desc);

arch/arc/plat-axs10x/axs10x.c

@@ -402,6 +402,8 @@ static void __init axs103_early_init(void)
 	unsigned int num_cores = (read_aux_reg(ARC_REG_MCIP_BCR) >> 16) & 0x3F;
 	if (num_cores > 2)
 		arc_set_core_freq(50 * 1000000);
+	else if (num_cores == 2)
+		arc_set_core_freq(75 * 1000000);
 #endif
 
 	switch (arc_get_core_freq()/1000000) {

arch/arm/Makefile

@@ -54,6 +54,14 @@ AS		+= -EL
 LD		+= -EL
 endif
 
+#
+# The Scalar Replacement of Aggregates (SRA) optimization pass in GCC 4.9 and
+# later may result in code being generated that handles signed short and signed
+# char struct members incorrectly. So disable it.
+# (https://gcc.gnu.org/bugzilla/show_bug.cgi?id=65932)
+#
+KBUILD_CFLAGS	+= $(call cc-option,-fno-ipa-sra)
+
 # This selects which instruction set is used.
 # Note that GCC does not numerically define an architecture version
 # macro, but instead defines a whole series of macros which makes

arch/arm/common/it8152.c

@@ -95,7 +95,7 @@ void it8152_init_irq(void)
 	}
 }
 
-void it8152_irq_demux(unsigned int irq, struct irq_desc *desc)
+void it8152_irq_demux(struct irq_desc *desc)
 {
        int bits_pd, bits_lp, bits_ld;
        int i;

arch/arm/common/locomo.c

@@ -138,7 +138,7 @@ static struct locomo_dev_info locomo_devices[] = {
 	},
 };
 
-static void locomo_handler(unsigned int __irq, struct irq_desc *desc)
+static void locomo_handler(struct irq_desc *desc)
 {
 	struct locomo *lchip = irq_desc_get_chip_data(desc);
 	int req, i;

arch/arm/common/sa1111.c

@@ -196,10 +196,8 @@ static struct sa1111_dev_info sa1111_devices[] = {
  * active IRQs causes the interrupt output to pulse, the upper levels
  * will call us again if there are more interrupts to process.
  */
-static void
-sa1111_irq_handler(unsigned int __irq, struct irq_desc *desc)
+static void sa1111_irq_handler(struct irq_desc *desc)
 {
-	unsigned int irq = irq_desc_get_irq(desc);
 	unsigned int stat0, stat1, i;
 	struct sa1111 *sachip = irq_desc_get_handler_data(desc);
 	void __iomem *mapbase = sachip->base + SA1111_INTC;
@@ -214,7 +212,7 @@ sa1111_irq_handler(unsigned int __irq, struct irq_desc *desc)
 	sa1111_writel(stat1, mapbase + SA1111_INTSTATCLR1);
 
 	if (stat0 == 0 && stat1 == 0) {
-		do_bad_IRQ(irq, desc);
+		do_bad_IRQ(desc);
 		return;
 	}
 

arch/arm/include/asm/assembler.h

@@ -491,11 +491,6 @@ THUMB(	orr	\reg , \reg , #PSR_T_BIT	)
 #endif
 	.endm
 
-	.macro	uaccess_save_and_disable, tmp
-	uaccess_save \tmp
-	uaccess_disable \tmp
-	.endm
-
 	.irp	c,,eq,ne,cs,cc,mi,pl,vs,vc,hi,ls,ge,lt,gt,le,hs,lo
 	.macro	ret\c, reg
 #if __LINUX_ARM_ARCH__ < 6

arch/arm/include/asm/bug.h

@@ -40,6 +40,7 @@ do {								\
 		"2:\t.asciz " #__file "\n" 			\
 		".popsection\n" 				\
 		".pushsection __bug_table,\"a\"\n"		\
+		".align 2\n"					\
 		"3:\t.word 1b, 2b\n"				\
 		"\t.hword " #__line ", 0\n"			\
 		".popsection");					\

arch/arm/include/asm/domain.h

@@ -12,6 +12,7 @@
 
 #ifndef __ASSEMBLY__
 #include <asm/barrier.h>
+#include <asm/thread_info.h>
 #endif
 
 /*
@@ -89,7 +90,8 @@ static inline unsigned int get_domain(void)
 
 	asm(
 	"mrc	p15, 0, %0, c3, c0	@ get domain"
-	 : "=r" (domain));
+	 : "=r" (domain)
+	 : "m" (current_thread_info()->cpu_domain));
 
 	return domain;
 }
@@ -98,7 +100,7 @@ static inline void set_domain(unsigned val)
 {
 	asm volatile(
 	"mcr	p15, 0, %0, c3, c0	@ set domain"
-	  : : "r" (val));
+	  : : "r" (val) : "memory");
 	isb();
 }
 

arch/arm/include/asm/hardware/it8152.h

@@ -106,7 +106,7 @@ extern void __iomem *it8152_base_address;
 struct pci_dev;
 struct pci_sys_data;
 
-extern void it8152_irq_demux(unsigned int irq, struct irq_desc *desc);
+extern void it8152_irq_demux(struct irq_desc *desc);
 extern void it8152_init_irq(void);
 extern int it8152_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin);
 extern int it8152_pci_setup(int nr, struct pci_sys_data *sys);

arch/arm/include/asm/hw_irq.h

@@ -11,12 +11,6 @@ static inline void ack_bad_irq(int irq)
 	pr_crit("unexpected IRQ trap at vector %02x\n", irq);
 }
 
-void set_irq_flags(unsigned int irq, unsigned int flags);
-
-#define IRQF_VALID	(1 << 0)
-#define IRQF_PROBE	(1 << 1)
-#define IRQF_NOAUTOEN	(1 << 2)
-
 #define ARCH_IRQ_INIT_FLAGS	(IRQ_NOREQUEST | IRQ_NOPROBE)
 
 #endif

arch/arm/include/asm/kvm_host.h

@@ -29,21 +29,18 @@
 
 #define __KVM_HAVE_ARCH_INTC_INITIALIZED
 
-#if defined(CONFIG_KVM_ARM_MAX_VCPUS)
-#define KVM_MAX_VCPUS CONFIG_KVM_ARM_MAX_VCPUS
-#else
-#define KVM_MAX_VCPUS 0
-#endif
-
 #define KVM_USER_MEM_SLOTS 32
 #define KVM_PRIVATE_MEM_SLOTS 4
 #define KVM_COALESCED_MMIO_PAGE_OFFSET 1
 #define KVM_HAVE_ONE_REG
+#define KVM_HALT_POLL_NS_DEFAULT 500000
 
 #define KVM_VCPU_MAX_FEATURES 2
 
 #include <kvm/arm_vgic.h>
 
+#define KVM_MAX_VCPUS VGIC_V2_MAX_CPUS
+
 u32 *kvm_vcpu_reg(struct kvm_vcpu *vcpu, u8 reg_num, u32 mode);
 int __attribute_const__ kvm_target_cpu(void);
 int kvm_reset_vcpu(struct kvm_vcpu *vcpu);
@@ -148,6 +145,7 @@ struct kvm_vm_stat {
 
 struct kvm_vcpu_stat {
 	u32 halt_successful_poll;
+	u32 halt_attempted_poll;
 	u32 halt_wakeup;
 };
 

arch/arm/include/asm/mach/irq.h

@@ -23,10 +23,10 @@ extern int show_fiq_list(struct seq_file *, int);
 /*
  * This is for easy migration, but should be changed in the source
  */
-#define do_bad_IRQ(irq,desc)				\
+#define do_bad_IRQ(desc)				\
 do {							\
 	raw_spin_lock(&desc->lock);			\
-	handle_bad_irq(irq, desc);			\
+	handle_bad_irq(desc);				\
 	raw_spin_unlock(&desc->lock);			\
 } while(0)
 

arch/arm/include/asm/thread_info.h

@@ -25,7 +25,6 @@
 struct task_struct;
 
 #include <asm/types.h>
-#include <asm/domain.h>
 
 typedef unsigned long mm_segment_t;
 

arch/arm/kernel/irq.c

@@ -79,26 +79,6 @@ asm_do_IRQ(unsigned int irq, struct pt_regs *regs)
 	handle_IRQ(irq, regs);
 }
 
-void set_irq_flags(unsigned int irq, unsigned int iflags)
-{
-	unsigned long clr = 0, set = IRQ_NOREQUEST | IRQ_NOPROBE | IRQ_NOAUTOEN;
-
-	if (irq >= nr_irqs) {
-		pr_err("Trying to set irq flags for IRQ%d\n", irq);
-		return;
-	}
-
-	if (iflags & IRQF_VALID)
-		clr |= IRQ_NOREQUEST;
-	if (iflags & IRQF_PROBE)
-		clr |= IRQ_NOPROBE;
-	if (!(iflags & IRQF_NOAUTOEN))
-		clr |= IRQ_NOAUTOEN;
-	/* Order is clear bits in "clr" then set bits in "set" */
-	irq_modify_status(irq, clr, set & ~clr);
-}
-EXPORT_SYMBOL_GPL(set_irq_flags);
-
 void __init init_IRQ(void)
 {
 	int ret;

arch/arm/kernel/kgdb.c

@@ -259,15 +259,17 @@ int kgdb_arch_set_breakpoint(struct kgdb_bkpt *bpt)
 	if (err)
 		return err;
 
-	patch_text((void *)bpt->bpt_addr,
-		   *(unsigned int *)arch_kgdb_ops.gdb_bpt_instr);
+	/* Machine is already stopped, so we can use __patch_text() directly */
+	__patch_text((void *)bpt->bpt_addr,
+		     *(unsigned int *)arch_kgdb_ops.gdb_bpt_instr);
 
 	return err;
 }
 
 int kgdb_arch_remove_breakpoint(struct kgdb_bkpt *bpt)
 {
-	patch_text((void *)bpt->bpt_addr, *(unsigned int *)bpt->saved_instr);
+	/* Machine is already stopped, so we can use __patch_text() directly */
+	__patch_text((void *)bpt->bpt_addr, *(unsigned int *)bpt->saved_instr);
 
 	return 0;
 }

arch/arm/kernel/process.c

@@ -226,6 +226,7 @@ copy_thread(unsigned long clone_flags, unsigned long stack_start,
 
 	memset(&thread->cpu_context, 0, sizeof(struct cpu_context_save));
 
+#ifdef CONFIG_CPU_USE_DOMAINS
 	/*
 	 * Copy the initial value of the domain access control register
 	 * from the current thread: thread->addr_limit will have been
@@ -233,6 +234,7 @@ copy_thread(unsigned long clone_flags, unsigned long stack_start,
 	 * kernel/fork.c
 	 */
 	thread->cpu_domain = get_domain();
+#endif
 
 	if (likely(!(p->flags & PF_KTHREAD))) {
 		*childregs = *current_pt_regs();

arch/arm/kernel/signal.c

@@ -343,15 +343,18 @@ setup_return(struct pt_regs *regs, struct ksignal *ksig,
 		 */
 		thumb = handler & 1;
 
-#if __LINUX_ARM_ARCH__ >= 7
 		/*
-		 * Clear the If-Then Thumb-2 execution state
-		 * ARM spec requires this to be all 000s in ARM mode
-		 * Snapdragon S4/Krait misbehaves on a Thumb=>ARM
-		 * signal transition without this.
+		 * Clear the If-Then Thumb-2 execution state.  ARM spec
+		 * requires this to be all 000s in ARM mode.  Snapdragon
+		 * S4/Krait misbehaves on a Thumb=>ARM signal transition
+		 * without this.
+		 *
+		 * We must do this whenever we are running on a Thumb-2
+		 * capable CPU, which includes ARMv6T2.  However, we elect
+		 * to always do this to simplify the code; this field is
+		 * marked UNK/SBZP for older architectures.
 		 */
 		cpsr &= ~PSR_IT_MASK;
-#endif
 
 		if (thumb) {
 			cpsr |= PSR_T_BIT;

arch/arm/kvm/Kconfig

@@ -45,15 +45,4 @@ config KVM_ARM_HOST
 	---help---
 	  Provides host support for ARM processors.
 
-config KVM_ARM_MAX_VCPUS
-	int "Number maximum supported virtual CPUs per VM"
-	depends on KVM_ARM_HOST
-	default 4
-	help
-	  Static number of max supported virtual CPUs per VM.
-
-	  If you choose a high number, the vcpu structures will be quite
-	  large, so only choose a reasonable number that you expect to
-	  actually use.
-
 endif # VIRTUALIZATION

arch/arm/kvm/arm.c

@@ -446,7 +446,7 @@ static int kvm_vcpu_first_run_init(struct kvm_vcpu *vcpu)
 	 * Map the VGIC hardware resources before running a vcpu the first
 	 * time on this VM.
 	 */
-	if (unlikely(!vgic_ready(kvm))) {
+	if (unlikely(irqchip_in_kernel(kvm) && !vgic_ready(kvm))) {
 		ret = kvm_vgic_map_resources(kvm);
 		if (ret)
 			return ret;

arch/arm/kvm/interrupts_head.S

@@ -515,8 +515,7 @@ ARM_BE8(rev	r6, r6  )
 
 	mrc	p15, 0, r2, c14, c3, 1	@ CNTV_CTL
 	str	r2, [vcpu, #VCPU_TIMER_CNTV_CTL]
-	bic	r2, #1			@ Clear ENABLE
-	mcr	p15, 0, r2, c14, c3, 1	@ CNTV_CTL
+
 	isb
 
 	mrrc	p15, 3, rr_lo_hi(r2, r3), c14	@ CNTV_CVAL
@@ -529,6 +528,9 @@ ARM_BE8(rev	r6, r6  )
 	mcrr	p15, 4, r2, r2, c14	@ CNTVOFF
 
 1:
+	mov	r2, #0			@ Clear ENABLE
+	mcr	p15, 0, r2, c14, c3, 1	@ CNTV_CTL
+
 	@ Allow physical timer/counter access for the host
 	mrc	p15, 4, r2, c14, c1, 0	@ CNTHCTL
 	orr	r2, r2, #(CNTHCTL_PL1PCEN | CNTHCTL_PL1PCTEN)

arch/arm/kvm/mmu.c

@@ -1792,8 +1792,10 @@ int kvm_arch_prepare_memory_region(struct kvm *kvm,
 		if (vma->vm_flags & VM_PFNMAP) {
 			gpa_t gpa = mem->guest_phys_addr +
 				    (vm_start - mem->userspace_addr);
-			phys_addr_t pa = (vma->vm_pgoff << PAGE_SHIFT) +
-					 vm_start - vma->vm_start;
+			phys_addr_t pa;
+
+			pa = (phys_addr_t)vma->vm_pgoff << PAGE_SHIFT;
+			pa += vm_start - vma->vm_start;
 
 			/* IO region dirty page logging not allowed */
 			if (memslot->flags & KVM_MEM_LOG_DIRTY_PAGES)

arch/arm/kvm/psci.c

@@ -126,7 +126,7 @@ static unsigned long kvm_psci_vcpu_on(struct kvm_vcpu *source_vcpu)
 
 static unsigned long kvm_psci_vcpu_affinity_info(struct kvm_vcpu *vcpu)
 {
-	int i;
+	int i, matching_cpus = 0;
 	unsigned long mpidr;
 	unsigned long target_affinity;
 	unsigned long target_affinity_mask;
@@ -151,12 +151,16 @@ static unsigned long kvm_psci_vcpu_affinity_info(struct kvm_vcpu *vcpu)
 	 */
 	kvm_for_each_vcpu(i, tmp, kvm) {
 		mpidr = kvm_vcpu_get_mpidr_aff(tmp);
-		if (((mpidr & target_affinity_mask) == target_affinity) &&
-		    !tmp->arch.pause) {
-			return PSCI_0_2_AFFINITY_LEVEL_ON;
+		if ((mpidr & target_affinity_mask) == target_affinity) {
+			matching_cpus++;
+			if (!tmp->arch.pause)
+				return PSCI_0_2_AFFINITY_LEVEL_ON;
 		}
 	}
 
+	if (!matching_cpus)
+		return PSCI_RET_INVALID_PARAMS;
+
 	return PSCI_0_2_AFFINITY_LEVEL_OFF;
 }
 

arch/arm/mach-dove/irq.c

@@ -69,14 +69,14 @@ static struct irq_chip pmu_irq_chip = {
 	.irq_ack	= pmu_irq_ack,
 };
 
-static void pmu_irq_handler(unsigned int __irq, struct irq_desc *desc)
+static void pmu_irq_handler(struct irq_desc *desc)
 {
-	unsigned int irq = irq_desc_get_irq(desc);
 	unsigned long cause = readl(PMU_INTERRUPT_CAUSE);
+	unsigned int irq;
 
 	cause &= readl(PMU_INTERRUPT_MASK);
 	if (cause == 0) {
-		do_bad_IRQ(irq, desc);
+		do_bad_IRQ(desc);
 		return;
 	}
 

arch/arm/mach-footbridge/isa-irq.c

@@ -87,13 +87,12 @@ static struct irq_chip isa_hi_chip = {
 	.irq_unmask	= isa_unmask_pic_hi_irq,
 };
 
-static void
-isa_irq_handler(unsigned int irq, struct irq_desc *desc)
+static void isa_irq_handler(struct irq_desc *desc)
 {
 	unsigned int isa_irq = *(unsigned char *)PCIIACK_BASE;
 
 	if (isa_irq < _ISA_IRQ(0) || isa_irq >= _ISA_IRQ(16)) {
-		do_bad_IRQ(isa_irq, desc);
+		do_bad_IRQ(desc);
 		return;
 	}
 

arch/arm/mach-gemini/gpio.c

@@ -126,7 +126,7 @@ static int gpio_set_irq_type(struct irq_data *d, unsigned int type)
 	return 0;
 }
 
-static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
+static void gpio_irq_handler(struct irq_desc *desc)
 {
 	unsigned int port = (unsigned int)irq_desc_get_handler_data(desc);
 	unsigned int gpio_irq_no, irq_stat;

arch/arm/mach-imx/3ds_debugboard.c

@@ -85,7 +85,7 @@ static struct platform_device smsc_lan9217_device = {
 	.resource = smsc911x_resources,
 };
 
-static void mxc_expio_irq_handler(u32 irq, struct irq_desc *desc)
+static void mxc_expio_irq_handler(struct irq_desc *desc)
 {
 	u32 imr_val;
 	u32 int_valid;

arch/arm/mach-imx/mach-mx31ads.c

@@ -154,7 +154,7 @@ static inline void mxc_init_imx_uart(void)
 	imx31_add_imx_uart0(&uart_pdata);
 }
 
-static void mx31ads_expio_irq_handler(u32 irq, struct irq_desc *desc)
+static void mx31ads_expio_irq_handler(struct irq_desc *desc)
 {
 	u32 imr_val;
 	u32 int_valid;

arch/arm/mach-iop13xx/msi.c

@@ -91,7 +91,7 @@ static void (*write_imipr[])(u32) = {
 	write_imipr_3,
 };
 
-static void iop13xx_msi_handler(unsigned int irq, struct irq_desc *desc)
+static void iop13xx_msi_handler(struct irq_desc *desc)
 {
 	int i, j;
 	unsigned long status;

arch/arm/mach-lpc32xx/irq.c

@@ -370,7 +370,7 @@ static struct irq_chip lpc32xx_irq_chip = {
 	.irq_set_wake = lpc32xx_irq_wake
 };
 
-static void lpc32xx_sic1_handler(unsigned int irq, struct irq_desc *desc)
+static void lpc32xx_sic1_handler(struct irq_desc *desc)
 {
 	unsigned long ints = __raw_readl(LPC32XX_INTC_STAT(LPC32XX_SIC1_BASE));
 
@@ -383,7 +383,7 @@ static void lpc32xx_sic1_handler(unsigned int irq, struct irq_desc *desc)
 	}
 }
 
-static void lpc32xx_sic2_handler(unsigned int irq, struct irq_desc *desc)
+static void lpc32xx_sic2_handler(struct irq_desc *desc)
 {
 	unsigned long ints = __raw_readl(LPC32XX_INTC_STAT(LPC32XX_SIC2_BASE));
 

arch/arm/mach-netx/generic.c

@@ -69,8 +69,7 @@ static struct platform_device *devices[] __initdata = {
 #define DEBUG_IRQ(fmt...)	while (0) {}
 #endif
 
-static void
-netx_hif_demux_handler(unsigned int irq_unused, struct irq_desc *desc)
+static void netx_hif_demux_handler(struct irq_desc *desc)
 {
 	unsigned int irq = NETX_IRQ_HIF_CHAINED(0);
 	unsigned int stat;

arch/arm/mach-omap1/fpga.c

@@ -87,7 +87,7 @@ static void fpga_mask_ack_irq(struct irq_data *d)
 	fpga_ack_irq(d);
 }
 
-static void innovator_fpga_IRQ_demux(unsigned int irq, struct irq_desc *desc)
+static void innovator_fpga_IRQ_demux(struct irq_desc *desc)
 {
 	u32 stat;
 	int fpga_irq;

arch/arm/mach-omap2/prm_common.c

@@ -102,7 +102,7 @@ static void omap_prcm_events_filter_priority(unsigned long *events,
  * dispatched accordingly. Clearing of the wakeup events should be
  * done by the SoC specific individual handlers.
  */
-static void omap_prcm_irq_handler(unsigned int irq, struct irq_desc *desc)
+static void omap_prcm_irq_handler(struct irq_desc *desc)
 {
 	unsigned long pending[OMAP_PRCM_MAX_NR_PENDING_REG];
 	unsigned long priority_pending[OMAP_PRCM_MAX_NR_PENDING_REG];

arch/arm/mach-pxa/balloon3.c

@@ -496,7 +496,7 @@ static struct irq_chip balloon3_irq_chip = {
 	.irq_unmask	= balloon3_unmask_irq,
 };
 
-static void balloon3_irq_handler(unsigned int __irq, struct irq_desc *desc)
+static void balloon3_irq_handler(struct irq_desc *desc)
 {
 	unsigned long pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
 					balloon3_irq_enabled;

arch/arm/mach-pxa/cm-x2xx-pci.c

@@ -29,13 +29,12 @@
 void __iomem *it8152_base_address;
 static int cmx2xx_it8152_irq_gpio;
 
-static void cmx2xx_it8152_irq_demux(unsigned int __irq, struct irq_desc *desc)
+static void cmx2xx_it8152_irq_demux(struct irq_desc *desc)
 {
-	unsigned int irq = irq_desc_get_irq(desc);
 	/* clear our parent irq */
 	desc->irq_data.chip->irq_ack(&desc->irq_data);
 
-	it8152_irq_demux(irq, desc);
+	it8152_irq_demux(desc);
 }
 
 void __cmx2xx_pci_init_irq(int irq_gpio)

arch/arm/mach-pxa/lpd270.c

@@ -120,7 +120,7 @@ static struct irq_chip lpd270_irq_chip = {
 	.irq_unmask	= lpd270_unmask_irq,
 };
 
-static void lpd270_irq_handler(unsigned int __irq, struct irq_desc *desc)
+static void lpd270_irq_handler(struct irq_desc *desc)
 {
 	unsigned int irq;
 	unsigned long pending;

arch/arm/mach-pxa/pcm990-baseboard.c

@@ -284,7 +284,7 @@ static struct irq_chip pcm990_irq_chip = {
 	.irq_unmask	= pcm990_unmask_irq,
 };
 
-static void pcm990_irq_handler(unsigned int __irq, struct irq_desc *desc)
+static void pcm990_irq_handler(struct irq_desc *desc)
 {
 	unsigned int irq;
 	unsigned long pending;

arch/arm/mach-pxa/viper.c

@@ -276,7 +276,7 @@ static inline unsigned long viper_irq_pending(void)
 			viper_irq_enabled_mask;
 }
 
-static void viper_irq_handler(unsigned int __irq, struct irq_desc *desc)
+static void viper_irq_handler(struct irq_desc *desc)
 {
 	unsigned int irq;
 	unsigned long pending;

arch/arm/mach-pxa/zeus.c

@@ -105,7 +105,7 @@ static inline unsigned long zeus_irq_pending(void)
 	return __raw_readw(ZEUS_CPLD_ISA_IRQ) & zeus_irq_enabled_mask;
 }
 
-static void zeus_irq_handler(unsigned int __irq, struct irq_desc *desc)
+static void zeus_irq_handler(struct irq_desc *desc)
 {
 	unsigned int irq;
 	unsigned long pending;

arch/arm/mach-rpc/ecard.c

@@ -551,8 +551,7 @@ static void ecard_check_lockup(struct irq_desc *desc)
 	}
 }
 
-static void
-ecard_irq_handler(unsigned int irq, struct irq_desc *desc)
+static void ecard_irq_handler(struct irq_desc *desc)
 {
 	ecard_t *ec;
 	int called = 0;

arch/arm/mach-s3c24xx/bast-irq.c

@@ -100,9 +100,7 @@ static struct irq_chip  bast_pc104_chip = {
 	.irq_ack	= bast_pc104_maskack
 };
 
-static void
-bast_irq_pc104_demux(unsigned int irq,
-		     struct irq_desc *desc)
+static void bast_irq_pc104_demux(struct irq_desc *desc)
 {
 	unsigned int stat;
 	unsigned int irqno;

arch/arm/mach-s3c64xx/common.c

@@ -388,22 +388,22 @@ static inline void s3c_irq_demux_eint(unsigned int start, unsigned int end)
 	}
 }
 
-static void s3c_irq_demux_eint0_3(unsigned int irq, struct irq_desc *desc)
+static void s3c_irq_demux_eint0_3(struct irq_desc *desc)
 {
 	s3c_irq_demux_eint(0, 3);
 }
 
-static void s3c_irq_demux_eint4_11(unsigned int irq, struct irq_desc *desc)
+static void s3c_irq_demux_eint4_11(struct irq_desc *desc)
 {
 	s3c_irq_demux_eint(4, 11);
 }
 
-static void s3c_irq_demux_eint12_19(unsigned int irq, struct irq_desc *desc)
+static void s3c_irq_demux_eint12_19(struct irq_desc *desc)
 {
 	s3c_irq_demux_eint(12, 19);
 }
 
-static void s3c_irq_demux_eint20_27(unsigned int irq, struct irq_desc *desc)
+static void s3c_irq_demux_eint20_27(struct irq_desc *desc)
 {
 	s3c_irq_demux_eint(20, 27);
 }

arch/arm/mach-sa1100/neponset.c

@@ -166,7 +166,7 @@ static struct sa1100_port_fns neponset_port_fns = {
  * ensure that the IRQ signal is deasserted before returning.  This
  * is rather unfortunate.
  */
-static void neponset_irq_handler(unsigned int irq, struct irq_desc *desc)
+static void neponset_irq_handler(struct irq_desc *desc)
 {
 	struct neponset_drvdata *d = irq_desc_get_handler_data(desc);
 	unsigned int irr;

arch/arm/mm/dma-mapping.c

@@ -1249,7 +1249,7 @@ __iommu_create_mapping(struct device *dev, struct page **pages, size_t size)
 	struct dma_iommu_mapping *mapping = to_dma_iommu_mapping(dev);
 	unsigned int count = PAGE_ALIGN(size) >> PAGE_SHIFT;
 	dma_addr_t dma_addr, iova;
-	int i, ret = DMA_ERROR_CODE;
+	int i;
 
 	dma_addr = __alloc_iova(mapping, size);
 	if (dma_addr == DMA_ERROR_CODE)
@@ -1257,6 +1257,8 @@ __iommu_create_mapping(struct device *dev, struct page **pages, size_t size)
 
 	iova = dma_addr;
 	for (i = 0; i < count; ) {
+		int ret;
+
 		unsigned int next_pfn = page_to_pfn(pages[i]) + 1;
 		phys_addr_t phys = page_to_phys(pages[i]);
 		unsigned int len, j;

arch/arm/nwfpe/entry.S

@@ -95,9 +95,10 @@ emulate:
 	reteq	r4			@ no, return failure
 
 next:
+	uaccess_enable r3
 .Lx1:	ldrt	r6, [r5], #4		@ get the next instruction and
 					@ increment PC
-
+	uaccess_disable r3
 	and	r2, r6, #0x0F000000	@ test for FP insns
 	teq	r2, #0x0C000000
 	teqne	r2, #0x0D000000

arch/arm/plat-orion/gpio.c

@@ -407,7 +407,7 @@ static int gpio_irq_set_type(struct irq_data *d, u32 type)
 	return 0;
 }
 
-static void gpio_irq_handler(unsigned __irq, struct irq_desc *desc)
+static void gpio_irq_handler(struct irq_desc *desc)
 {
 	struct orion_gpio_chip *ochip = irq_desc_get_handler_data(desc);
 	u32 cause, type;

arch/arm/xen/hypercall.S

@@ -98,8 +98,23 @@ ENTRY(privcmd_call)
 	mov r1, r2
 	mov r2, r3
 	ldr r3, [sp, #8]
+	/*
+	 * Privcmd calls are issued by the userspace. We need to allow the
+	 * kernel to access the userspace memory before issuing the hypercall.
+	 */
+	uaccess_enable r4
+
+	/* r4 is loaded now as we use it as scratch register before */
 	ldr r4, [sp, #4]
 	__HVC(XEN_IMM)
+
+	/*
+	 * Disable userspace access from kernel. This is fine to do it
+	 * unconditionally as no set_fs(KERNEL_DS)/set_fs(get_ds()) is
+	 * called before.
+	 */
+	uaccess_disable r4
+
 	ldm sp!, {r4}
 	ret lr
 ENDPROC(privcmd_call);

arch/arm64/Kconfig

@@ -32,6 +32,7 @@ config ARM64
 	select GENERIC_CLOCKEVENTS_BROADCAST
 	select GENERIC_CPU_AUTOPROBE
 	select GENERIC_EARLY_IOREMAP
+	select GENERIC_IDLE_POLL_SETUP
 	select GENERIC_IRQ_PROBE
 	select GENERIC_IRQ_SHOW
 	select GENERIC_IRQ_SHOW_LEVEL
@@ -331,6 +332,22 @@ config ARM64_ERRATUM_845719
 
 	  If unsure, say Y.
 
+config ARM64_ERRATUM_843419
+	bool "Cortex-A53: 843419: A load or store might access an incorrect address"
+	depends on MODULES
+	default y
+	help
+	  This option builds kernel modules using the large memory model in
+	  order to avoid the use of the ADRP instruction, which can cause
+	  a subsequent memory access to use an incorrect address on Cortex-A53
+	  parts up to r0p4.
+
+	  Note that the kernel itself must be linked with a version of ld
+	  which fixes potentially affected ADRP instructions through the
+	  use of veneers.
+
+	  If unsure, say Y.
+
 endmenu
 
 

arch/arm64/Makefile

@@ -41,6 +41,10 @@ endif
 
 CHECKFLAGS	+= -D__aarch64__
 
+ifeq ($(CONFIG_ARM64_ERRATUM_843419), y)
+CFLAGS_MODULE	+= -mcmodel=large
+endif
+
 # Default value
 head-y		:= arch/arm64/kernel/head.o
 

arch/arm64/boot/dts/mediatek/mt8173.dtsi

@@ -81,7 +81,7 @@
 		};
 
 		idle-states {
-			entry-method = "arm,psci";
+			entry-method = "psci";
 
 			CPU_SLEEP_0: cpu-sleep-0 {
 				compatible = "arm,idle-state";

arch/arm64/boot/dts/rockchip/rk3368.dtsi

@@ -106,7 +106,7 @@
 		};
 
 		idle-states {
-			entry-method = "arm,psci";
+			entry-method = "psci";
 
 			cpu_sleep: cpu-sleep-0 {
 				compatible = "arm,idle-state";

arch/arm64/include/asm/hardirq.h

@@ -43,9 +43,4 @@ static inline void ack_bad_irq(unsigned int irq)
 	irq_err_count++;
 }
 
-/*
- * No arch-specific IRQ flags.
- */
-#define set_irq_flags(irq, flags)
-
 #endif /* __ASM_HARDIRQ_H */

arch/arm64/include/asm/kvm_arm.h

@@ -95,6 +95,7 @@
 			 SCTLR_EL2_SA | SCTLR_EL2_I)
 
 /* TCR_EL2 Registers bits */
+#define TCR_EL2_RES1	((1 << 31) | (1 << 23))
 #define TCR_EL2_TBI	(1 << 20)
 #define TCR_EL2_PS	(7 << 16)
 #define TCR_EL2_PS_40B	(2 << 16)
@@ -106,9 +107,10 @@
 #define TCR_EL2_MASK	(TCR_EL2_TG0 | TCR_EL2_SH0 | \
 			 TCR_EL2_ORGN0 | TCR_EL2_IRGN0 | TCR_EL2_T0SZ)
 
-#define TCR_EL2_FLAGS	(TCR_EL2_PS_40B)
+#define TCR_EL2_FLAGS	(TCR_EL2_RES1 | TCR_EL2_PS_40B)
 
 /* VTCR_EL2 Registers bits */
+#define VTCR_EL2_RES1		(1 << 31)
 #define VTCR_EL2_PS_MASK	(7 << 16)
 #define VTCR_EL2_TG0_MASK	(1 << 14)
 #define VTCR_EL2_TG0_4K		(0 << 14)
@@ -147,7 +149,8 @@
  */
 #define VTCR_EL2_FLAGS		(VTCR_EL2_TG0_64K | VTCR_EL2_SH0_INNER | \
 				 VTCR_EL2_ORGN0_WBWA | VTCR_EL2_IRGN0_WBWA | \
-				 VTCR_EL2_SL0_LVL1 | VTCR_EL2_T0SZ_40B)
+				 VTCR_EL2_SL0_LVL1 | VTCR_EL2_T0SZ_40B | \
+				 VTCR_EL2_RES1)
 #define VTTBR_X		(38 - VTCR_EL2_T0SZ_40B)
 #else
 /*
@@ -158,7 +161,8 @@
  */
 #define VTCR_EL2_FLAGS		(VTCR_EL2_TG0_4K | VTCR_EL2_SH0_INNER | \
 				 VTCR_EL2_ORGN0_WBWA | VTCR_EL2_IRGN0_WBWA | \
-				 VTCR_EL2_SL0_LVL1 | VTCR_EL2_T0SZ_40B)
+				 VTCR_EL2_SL0_LVL1 | VTCR_EL2_T0SZ_40B | \
+				 VTCR_EL2_RES1)
 #define VTTBR_X		(37 - VTCR_EL2_T0SZ_40B)
 #endif
 
@@ -168,7 +172,6 @@
 #define VTTBR_VMID_MASK	  (UL(0xFF) << VTTBR_VMID_SHIFT)
 
 /* Hyp System Trap Register */
-#define HSTR_EL2_TTEE	(1 << 16)
 #define HSTR_EL2_T(x)	(1 << x)
 
 /* Hyp Coproccessor Trap Register Shifts */

arch/arm64/include/asm/kvm_asm.h

@@ -53,9 +53,7 @@
 #define	IFSR32_EL2	25	/* Instruction Fault Status Register */
 #define	FPEXC32_EL2	26	/* Floating-Point Exception Control Register */
 #define	DBGVCR32_EL2	27	/* Debug Vector Catch Register */
-#define	TEECR32_EL1	28	/* ThumbEE Configuration Register */
-#define	TEEHBR32_EL1	29	/* ThumbEE Handler Base Register */
-#define	NR_SYS_REGS	30
+#define	NR_SYS_REGS	28
 
 /* 32bit mapping */
 #define c0_MPIDR	(MPIDR_EL1 * 2)	/* MultiProcessor ID Register */

arch/arm64/include/asm/kvm_host.h

@@ -30,19 +30,16 @@
 
 #define __KVM_HAVE_ARCH_INTC_INITIALIZED
 
-#if defined(CONFIG_KVM_ARM_MAX_VCPUS)
-#define KVM_MAX_VCPUS CONFIG_KVM_ARM_MAX_VCPUS
-#else
-#define KVM_MAX_VCPUS 0
-#endif
-
 #define KVM_USER_MEM_SLOTS 32
 #define KVM_PRIVATE_MEM_SLOTS 4
 #define KVM_COALESCED_MMIO_PAGE_OFFSET 1
+#define KVM_HALT_POLL_NS_DEFAULT 500000
 
 #include <kvm/arm_vgic.h>
 #include <kvm/arm_arch_timer.h>
 
+#define KVM_MAX_VCPUS VGIC_V3_MAX_CPUS
+
 #define KVM_VCPU_MAX_FEATURES 3
 
 int __attribute_const__ kvm_target_cpu(void);
@@ -195,6 +192,7 @@ struct kvm_vm_stat {
 
 struct kvm_vcpu_stat {
 	u32 halt_successful_poll;
+	u32 halt_attempted_poll;
 	u32 halt_wakeup;
 };
 

arch/arm64/include/asm/pgtable.h

@@ -26,13 +26,9 @@
  * Software defined PTE bits definition.
  */
 #define PTE_VALID		(_AT(pteval_t, 1) << 0)
+#define PTE_WRITE		(PTE_DBM)		 /* same as DBM (51) */
 #define PTE_DIRTY		(_AT(pteval_t, 1) << 55)
 #define PTE_SPECIAL		(_AT(pteval_t, 1) << 56)
-#ifdef CONFIG_ARM64_HW_AFDBM
-#define PTE_WRITE		(PTE_DBM)		 /* same as DBM */
-#else
-#define PTE_WRITE		(_AT(pteval_t, 1) << 57)
-#endif
 #define PTE_PROT_NONE		(_AT(pteval_t, 1) << 58) /* only when !PTE_VALID */
 
 /*
@@ -146,7 +142,7 @@ extern struct page *empty_zero_page;
 #define pte_exec(pte)		(!(pte_val(pte) & PTE_UXN))
 
 #ifdef CONFIG_ARM64_HW_AFDBM
-#define pte_hw_dirty(pte)	(!(pte_val(pte) & PTE_RDONLY))
+#define pte_hw_dirty(pte)	(pte_write(pte) && !(pte_val(pte) & PTE_RDONLY))
 #else
 #define pte_hw_dirty(pte)	(0)
 #endif
@@ -238,7 +234,7 @@ extern void __sync_icache_dcache(pte_t pteval, unsigned long addr);
  * When hardware DBM is not present, the sofware PTE_DIRTY bit is updated via
  * the page fault mechanism. Checking the dirty status of a pte becomes:
  *
- *   PTE_DIRTY || !PTE_RDONLY
+ *   PTE_DIRTY || (PTE_WRITE && !PTE_RDONLY)
  */
 static inline void set_pte_at(struct mm_struct *mm, unsigned long addr,
 			      pte_t *ptep, pte_t pte)
@@ -503,7 +499,7 @@ static inline pte_t pte_modify(pte_t pte, pgprot_t newprot)
 			      PTE_PROT_NONE | PTE_WRITE | PTE_TYPE_MASK;
 	/* preserve the hardware dirty information */
 	if (pte_hw_dirty(pte))
-		newprot |= PTE_DIRTY;
+		pte = pte_mkdirty(pte);
 	pte_val(pte) = (pte_val(pte) & ~mask) | (pgprot_val(newprot) & mask);
 	return pte;
 }

arch/arm64/kernel/debug-monitors.c

@@ -134,7 +134,7 @@ static int os_lock_notify(struct notifier_block *self,
 				    unsigned long action, void *data)
 {
 	int cpu = (unsigned long)data;
-	if (action == CPU_ONLINE)
+	if ((action & ~CPU_TASKS_FROZEN) == CPU_ONLINE)
 		smp_call_function_single(cpu, clear_os_lock, NULL, 1);
 	return NOTIFY_OK;
 }

arch/arm64/kernel/head.S

@@ -523,6 +523,11 @@ CPU_LE(	movk	x0, #0x30d0, lsl #16	)	// Clear EE and E0E on LE systems
 	msr	hstr_el2, xzr			// Disable CP15 traps to EL2
 #endif
 
+	/* EL2 debug */
+	mrs	x0, pmcr_el0			// Disable debug access traps
+	ubfx	x0, x0, #11, #5			// to EL2 and allow access to
+	msr	mdcr_el2, x0			// all PMU counters from EL1
+
 	/* Stage-2 translation */
 	msr	vttbr_el2, xzr
 

arch/arm64/kernel/hw_breakpoint.c

@@ -872,7 +872,7 @@ static int hw_breakpoint_reset_notify(struct notifier_block *self,
 						void *hcpu)
 {
 	int cpu = (long)hcpu;
-	if (action == CPU_ONLINE)
+	if ((action & ~CPU_TASKS_FROZEN) == CPU_ONLINE)
 		smp_call_function_single(cpu, hw_breakpoint_reset, NULL, 1);
 	return NOTIFY_OK;
 }

arch/arm64/kernel/module.c

@@ -332,12 +332,14 @@ int apply_relocate_add(Elf64_Shdr *sechdrs,
 			ovf = reloc_insn_imm(RELOC_OP_PREL, loc, val, 0, 21,
 					     AARCH64_INSN_IMM_ADR);
 			break;
+#ifndef CONFIG_ARM64_ERRATUM_843419
 		case R_AARCH64_ADR_PREL_PG_HI21_NC:
 			overflow_check = false;
 		case R_AARCH64_ADR_PREL_PG_HI21:
 			ovf = reloc_insn_imm(RELOC_OP_PAGE, loc, val, 12, 21,
 					     AARCH64_INSN_IMM_ADR);
 			break;
+#endif
 		case R_AARCH64_ADD_ABS_LO12_NC:
 		case R_AARCH64_LDST8_ABS_LO12_NC:
 			overflow_check = false;

arch/arm64/kernel/signal32.c

@@ -212,14 +212,32 @@ int copy_siginfo_from_user32(siginfo_t *to, compat_siginfo_t __user *from)
 
 /*
  * VFP save/restore code.
+ *
+ * We have to be careful with endianness, since the fpsimd context-switch
+ * code operates on 128-bit (Q) register values whereas the compat ABI
+ * uses an array of 64-bit (D) registers. Consequently, we need to swap
+ * the two halves of each Q register when running on a big-endian CPU.
  */
+union __fpsimd_vreg {
+	__uint128_t	raw;
+	struct {
+#ifdef __AARCH64EB__
+		u64	hi;
+		u64	lo;
+#else
+		u64	lo;
+		u64	hi;
+#endif
+	};
+};
+
 static int compat_preserve_vfp_context(struct compat_vfp_sigframe __user *frame)
 {
 	struct fpsimd_state *fpsimd = &current->thread.fpsimd_state;
 	compat_ulong_t magic = VFP_MAGIC;
 	compat_ulong_t size = VFP_STORAGE_SIZE;
 	compat_ulong_t fpscr, fpexc;
-	int err = 0;
+	int i, err = 0;
 
 	/*
 	 * Save the hardware registers to the fpsimd_state structure.
@@ -235,10 +253,15 @@ static int compat_preserve_vfp_context(struct compat_vfp_sigframe __user *frame)
 	/*
 	 * Now copy the FP registers. Since the registers are packed,
 	 * we can copy the prefix we want (V0-V15) as it is.
-	 * FIXME: Won't work if big endian.
 	 */
-	err |= __copy_to_user(&frame->ufp.fpregs, fpsimd->vregs,
-			      sizeof(frame->ufp.fpregs));
+	for (i = 0; i < ARRAY_SIZE(frame->ufp.fpregs); i += 2) {
+		union __fpsimd_vreg vreg = {
+			.raw = fpsimd->vregs[i >> 1],
+		};
+
+		__put_user_error(vreg.lo, &frame->ufp.fpregs[i], err);
+		__put_user_error(vreg.hi, &frame->ufp.fpregs[i + 1], err);
+	}
 
 	/* Create an AArch32 fpscr from the fpsr and the fpcr. */
 	fpscr = (fpsimd->fpsr & VFP_FPSCR_STAT_MASK) |
@@ -263,7 +286,7 @@ static int compat_restore_vfp_context(struct compat_vfp_sigframe __user *frame)
 	compat_ulong_t magic = VFP_MAGIC;
 	compat_ulong_t size = VFP_STORAGE_SIZE;
 	compat_ulong_t fpscr;
-	int err = 0;
+	int i, err = 0;
 
 	__get_user_error(magic, &frame->magic, err);
 	__get_user_error(size, &frame->size, err);
@@ -273,12 +296,14 @@ static int compat_restore_vfp_context(struct compat_vfp_sigframe __user *frame)
 	if (magic != VFP_MAGIC || size != VFP_STORAGE_SIZE)
 		return -EINVAL;
 
-	/*
-	 * Copy the FP registers into the start of the fpsimd_state.
-	 * FIXME: Won't work if big endian.
-	 */
-	err |= __copy_from_user(fpsimd.vregs, frame->ufp.fpregs,
-				sizeof(frame->ufp.fpregs));
+	/* Copy the FP registers into the start of the fpsimd_state. */
+	for (i = 0; i < ARRAY_SIZE(frame->ufp.fpregs); i += 2) {
+		union __fpsimd_vreg vreg;
+
+		__get_user_error(vreg.lo, &frame->ufp.fpregs[i], err);
+		__get_user_error(vreg.hi, &frame->ufp.fpregs[i + 1], err);
+		fpsimd.vregs[i >> 1] = vreg.raw;
+	}
 
 	/* Extract the fpsr and the fpcr from the fpscr */
 	__get_user_error(fpscr, &frame->ufp.fpscr, err);

arch/arm64/kvm/Kconfig

@@ -41,15 +41,4 @@ config KVM_ARM_HOST
 	---help---
 	  Provides host support for ARM processors.
 
-config KVM_ARM_MAX_VCPUS
-	int "Number maximum supported virtual CPUs per VM"
-	depends on KVM_ARM_HOST
-	default 4
-	help
-	  Static number of max supported virtual CPUs per VM.
-
-	  If you choose a high number, the vcpu structures will be quite
-	  large, so only choose a reasonable number that you expect to
-	  actually use.
-
 endif # VIRTUALIZATION

arch/arm64/kvm/hyp.S

@@ -433,20 +433,13 @@
 	mrs	x5, ifsr32_el2
 	stp	x4, x5, [x3]
 
-	skip_fpsimd_state x8, 3f
+	skip_fpsimd_state x8, 2f
 	mrs	x6, fpexc32_el2
 	str	x6, [x3, #16]
-3:
-	skip_debug_state x8, 2f
+2:
+	skip_debug_state x8, 1f
 	mrs	x7, dbgvcr32_el2
 	str	x7, [x3, #24]
-2:
-	skip_tee_state x8, 1f
-
-	add	x3, x2, #CPU_SYSREG_OFFSET(TEECR32_EL1)
-	mrs	x4, teecr32_el1
-	mrs	x5, teehbr32_el1
-	stp	x4, x5, [x3]
 1:
 .endm
 
@@ -466,16 +459,9 @@
 	msr	dacr32_el2, x4
 	msr	ifsr32_el2, x5
 
-	skip_debug_state x8, 2f
+	skip_debug_state x8, 1f
 	ldr	x7, [x3, #24]
 	msr	dbgvcr32_el2, x7
-2:
-	skip_tee_state x8, 1f
-
-	add	x3, x2, #CPU_SYSREG_OFFSET(TEECR32_EL1)
-	ldp	x4, x5, [x3]
-	msr	teecr32_el1, x4
-	msr	teehbr32_el1, x5
 1:
 .endm
 
@@ -570,8 +556,6 @@ alternative_endif
 	mrs	x3, cntv_ctl_el0
 	and	x3, x3, #3
 	str	w3, [x0, #VCPU_TIMER_CNTV_CTL]
-	bic	x3, x3, #1		// Clear Enable
-	msr	cntv_ctl_el0, x3
 
 	isb
 
@@ -579,6 +563,9 @@ alternative_endif
 	str	x3, [x0, #VCPU_TIMER_CNTV_CVAL]
 
 1:
+	// Disable the virtual timer
+	msr	cntv_ctl_el0, xzr
+
 	// Allow physical timer/counter access for the host
 	mrs	x2, cnthctl_el2
 	orr	x2, x2, #3
@@ -753,6 +740,9 @@ ENTRY(__kvm_vcpu_run)
 	// Guest context
 	add	x2, x0, #VCPU_CONTEXT
 
+	// We must restore the 32-bit state before the sysregs, thanks
+	// to Cortex-A57 erratum #852523.
+	restore_guest_32bit_state
 	bl __restore_sysregs
 
 	skip_debug_state x3, 1f
@@ -760,7 +750,6 @@ ENTRY(__kvm_vcpu_run)
 	kern_hyp_va x3
 	bl	__restore_debug
 1:
-	restore_guest_32bit_state
 	restore_guest_regs
 
 	// That's it, no more messing around.

arch/arm64/kvm/sys_regs.c

@@ -272,7 +272,7 @@ static int set_bvr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
 {
 	__u64 *r = &vcpu->arch.vcpu_debug_state.dbg_bvr[rd->reg];
 
-	if (copy_from_user(uaddr, r, KVM_REG_SIZE(reg->id)) != 0)
+	if (copy_from_user(r, uaddr, KVM_REG_SIZE(reg->id)) != 0)
 		return -EFAULT;
 	return 0;
 }
@@ -314,7 +314,7 @@ static int set_bcr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
 {
 	__u64 *r = &vcpu->arch.vcpu_debug_state.dbg_bcr[rd->reg];
 
-	if (copy_from_user(uaddr, r, KVM_REG_SIZE(reg->id)) != 0)
+	if (copy_from_user(r, uaddr, KVM_REG_SIZE(reg->id)) != 0)
 		return -EFAULT;
 
 	return 0;
@@ -358,7 +358,7 @@ static int set_wvr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
 {
 	__u64 *r = &vcpu->arch.vcpu_debug_state.dbg_wvr[rd->reg];
 
-	if (copy_from_user(uaddr, r, KVM_REG_SIZE(reg->id)) != 0)
+	if (copy_from_user(r, uaddr, KVM_REG_SIZE(reg->id)) != 0)
 		return -EFAULT;
 	return 0;
 }
@@ -400,7 +400,7 @@ static int set_wcr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
 {
 	__u64 *r = &vcpu->arch.vcpu_debug_state.dbg_wcr[rd->reg];
 
-	if (copy_from_user(uaddr, r, KVM_REG_SIZE(reg->id)) != 0)
+	if (copy_from_user(r, uaddr, KVM_REG_SIZE(reg->id)) != 0)
 		return -EFAULT;
 	return 0;
 }
@@ -539,13 +539,6 @@ static const struct sys_reg_desc sys_reg_descs[] = {
 	{ Op0(0b10), Op1(0b000), CRn(0b0111), CRm(0b1110), Op2(0b110),
 	  trap_dbgauthstatus_el1 },
 
-	/* TEECR32_EL1 */
-	{ Op0(0b10), Op1(0b010), CRn(0b0000), CRm(0b0000), Op2(0b000),
-	  NULL, reset_val, TEECR32_EL1, 0 },
-	/* TEEHBR32_EL1 */
-	{ Op0(0b10), Op1(0b010), CRn(0b0001), CRm(0b0000), Op2(0b000),
-	  NULL, reset_val, TEEHBR32_EL1, 0 },
-
 	/* MDCCSR_EL1 */
 	{ Op0(0b10), Op1(0b011), CRn(0b0000), CRm(0b0001), Op2(0b000),
 	  trap_raz_wi },

arch/arm64/mm/dma-mapping.c

@@ -100,7 +100,7 @@ static void *__dma_alloc_coherent(struct device *dev, size_t size,
 	if (IS_ENABLED(CONFIG_ZONE_DMA) &&
 	    dev->coherent_dma_mask <= DMA_BIT_MASK(32))
 		flags |= GFP_DMA;
-	if (IS_ENABLED(CONFIG_DMA_CMA) && (flags & __GFP_WAIT)) {
+	if (dev_get_cma_area(dev) && (flags & __GFP_WAIT)) {
 		struct page *page;
 		void *addr;
 

arch/avr32/mach-at32ap/extint.c

@@ -144,7 +144,7 @@ static struct irq_chip eic_chip = {
 	.irq_set_type	= eic_set_irq_type,
 };
 
-static void demux_eic_irq(unsigned int irq, struct irq_desc *desc)
+static void demux_eic_irq(struct irq_desc *desc)
 {
 	struct eic *eic = irq_desc_get_handler_data(desc);
 	unsigned long status, pending;

arch/avr32/mach-at32ap/pio.c

@@ -281,7 +281,7 @@ static struct irq_chip gpio_irqchip = {
 	.irq_set_type	= gpio_irq_type,
 };
 
-static void gpio_irq_handler(unsigned irq, struct irq_desc *desc)
+static void gpio_irq_handler(struct irq_desc *desc)
 {
 	struct pio_device	*pio = irq_desc_get_chip_data(desc);
 	unsigned		gpio_irq;

arch/blackfin/include/asm/irq_handler.h

@@ -60,7 +60,7 @@ extern void bfin_internal_mask_irq(unsigned int irq);
 extern void bfin_internal_unmask_irq(unsigned int irq);
 
 struct irq_desc;
-extern void bfin_demux_mac_status_irq(unsigned int, struct irq_desc *);
-extern void bfin_demux_gpio_irq(unsigned int, struct irq_desc *);
+extern void bfin_demux_mac_status_irq(struct irq_desc *);
+extern void bfin_demux_gpio_irq(struct irq_desc *);
 
 #endif

arch/blackfin/kernel/irqchip.c

@@ -107,7 +107,7 @@ asmlinkage void asm_do_IRQ(unsigned int irq, struct pt_regs *regs)
 	 * than crashing, do something sensible.
 	 */
 	if (irq >= NR_IRQS)
-		handle_bad_irq(irq, &bad_irq_desc);
+		handle_bad_irq(&bad_irq_desc);
 	else
 		generic_handle_irq(irq);
 

arch/blackfin/mach-bf537/ints-priority.c

@@ -89,8 +89,7 @@ static struct irq_chip bf537_generic_error_irqchip = {
 	.irq_unmask = bf537_generic_error_unmask_irq,
 };
 
-static void bf537_demux_error_irq(unsigned int int_err_irq,
-				  struct irq_desc *inta_desc)
+static void bf537_demux_error_irq(struct irq_desc *inta_desc)
 {
 	int irq = 0;
 
@@ -182,15 +181,12 @@ static struct irq_chip bf537_mac_rx_irqchip = {
 	.irq_unmask = bf537_mac_rx_unmask_irq,
 };
 
-static void bf537_demux_mac_rx_irq(unsigned int __int_irq,
-				   struct irq_desc *desc)
+static void bf537_demux_mac_rx_irq(struct irq_desc *desc)
 {
-	unsigned int int_irq = irq_desc_get_irq(desc);
-
 	if (bfin_read_DMA1_IRQ_STATUS() & (DMA_DONE | DMA_ERR))
 		bfin_handle_irq(IRQ_MAC_RX);
 	else
-		bfin_demux_gpio_irq(int_irq, desc);
+		bfin_demux_gpio_irq(desc);
 }
 #endif
 

arch/blackfin/mach-common/ints-priority.c

@@ -656,8 +656,7 @@ static struct irq_chip bfin_mac_status_irqchip = {
 	.irq_set_wake = bfin_mac_status_set_wake,
 };
 
-void bfin_demux_mac_status_irq(unsigned int int_err_irq,
-			       struct irq_desc *inta_desc)
+void bfin_demux_mac_status_irq(struct irq_desc *inta_desc)
 {
 	int i, irq = 0;
 	u32 status = bfin_read_EMAC_SYSTAT();
@@ -825,7 +824,7 @@ static void bfin_demux_gpio_block(unsigned int irq)
 	}
 }
 
-void bfin_demux_gpio_irq(unsigned int __inta_irq, struct irq_desc *desc)
+void bfin_demux_gpio_irq(struct irq_desc *desc)
 {
 	unsigned int inta_irq = irq_desc_get_irq(desc);
 	unsigned int irq;

arch/c6x/platforms/megamod-pic.c

@@ -93,7 +93,7 @@ static struct irq_chip megamod_chip = {
 	.irq_unmask	= unmask_megamod,
 };
 
-static void megamod_irq_cascade(unsigned int __irq, struct irq_desc *desc)
+static void megamod_irq_cascade(struct irq_desc *desc)
 {
 	struct megamod_cascade_data *cascade;
 	struct megamod_pic *pic;