Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC DT updates from Kevin Hilman:
 "As usual, quite a few device-tree updates in ARM land.  There was one
  minor churn in DTs due to relicensing under a dual-license, and lots
  of little additions of new peripherals, features etc, but nothing
  really exciting to call to your attention.  Some higlights, focsuing
  on support for new SoCs and boards:

   - AT91: new boards: Overkiz,  Acme Systems' Arietta G25
   - tegra: HDA support
   - bcm: new platforms: Buffalo WXR-1900DHP, SmartRG SR400ac, ASUS
     RT-AC87U
   - mvebu: new platforms: Compulab CM-A510, Armada 385-based Linksys
     boards, DLink DNS-327L
   - OMAP: new platforms: Baltos IR5221, LogicPD Torpedo, Toby-Churchill
     SL50
   - ARM: added support for Juno r1 board
   - sunxi: A33 SoC support; new boards: A23 EVB, SinA33, GA10H-A33,
     Mele A1000G
   - imx: i.MX7D SoC support; new boards: Armadeus Systems APF6,
     Gateworks GW5510, and aristainetos2 boards
   - hisilicon: hi6220 SoC support; new boards: 96boards hikey"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (462 commits)
  ARM: hisi: revert changes from hisi/hip04-dt branch
  ARM: nomadik: set proper compatible for accelerometer
  ARM64: juno: add GPIO keys
  ARM: at91/dt: sama5d4: fix dma conf for aes, sha and tdes nodes
  ARM: dts: Introduce STM32F429 MCU
  ARM: socfpga: dts: enable ethernet for Arria10 devkit
  ARM: dts: k2l: fix the netcp range size
  ARM: dts: k2e: fix the netcp range size
  ARM: dts: k2hk: fix the netcp range size
  ARM: dts: k2l-evm: Add device bindings for netcp driver
  ARM: dts: k2e-evm: Add device bindings for netcp driver
  ARM: dts: k2hk-evm: Add device bindings for netcp driver
  ARM: BCM5301X: Add DT for Asus RT-AC87U
  ARM: BCM5301X: add IRQ numbers for PCIe controller
  ARM: BCM5301X: add NAND flash chip description
  arm64: dts: Add dts files for Hisilicon Hi6220 SoC
  clk: hi6220: Document devicetree bindings for hi6220 clock
  arm64: hi6220: Document devicetree bindings for Hisilicon hi6220 SoC
  ARM: at91/dt: sama5d4ek: mci0 uses slot 0
  ARM: at91/dt: kizbox: fix mismatch LED PWM device
  ...

Documentation/devicetree/bindings/arm/altera/socfpga-sdram-controller.txt

@@ -0,0 +1,12 @@
+Altera SOCFPGA SDRAM Controller
+
+Required properties:
+- compatible : Should contain "altr,sdr-ctl" and "syscon".
+  syscon is required by the Altera SOCFPGA SDRAM EDAC.
+- reg : Should contain 1 register range (address and length)
+
+Example:
+	sdr: sdr@ffc25000 {
+		compatible = "altr,sdr-ctl", "syscon";
+		reg = <0xffc25000 0x1000>;
+	};

Documentation/devicetree/bindings/arm/arm-boards

@@ -157,3 +157,69 @@ Example:
 
 	};
 };
+
+ARM Versatile Express Boards
+-----------------------------
+For details on the device tree bindings for ARM Versatile Express boards
+please consult the vexpress.txt file in the same directory as this file.
+
+ARM Juno Boards
+----------------
+The Juno boards are targeting development for AArch64 systems. The first
+iteration, Juno r0, is a vehicle for evaluating big.LITTLE on AArch64,
+with the second iteration, Juno r1, mainly aimed at development of PCIe
+based systems. Juno r1 also has support for AXI masters placed on the TLX
+connectors to join the coherency domain.
+
+Juno boards are described in a similar way to ARM Versatile Express boards,
+with the motherboard part of the hardware being described in a separate file
+to highlight the fact that is part of the support infrastructure for the SoC.
+Juno device tree bindings also share the Versatile Express bindings as
+described under the RS1 memory mapping.
+
+Required properties (in root node):
+	compatible = "arm,juno";	/* For Juno r0 board */
+	compatible = "arm,juno-r1";	/* For Juno r1 board */
+
+Required nodes:
+The description for the board must include:
+   - a "psci" node describing the boot method used for the secondary CPUs.
+     A detailed description of the bindings used for "psci" nodes is present
+     in the psci.txt file.
+   - a "cpus" node describing the available cores and their associated
+     "enable-method"s. For more details see cpus.txt file.
+
+Example:
+
+/dts-v1/;
+/ {
+	model = "ARM Juno development board (r0)";
+	compatible = "arm,juno", "arm,vexpress";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		A57_0: cpu@0 {
+			compatible = "arm,cortex-a57","arm,armv8";
+			reg = <0x0 0x0>;
+			device_type = "cpu";
+			enable-method = "psci";
+		};
+
+		.....
+
+		A53_0: cpu@100 {
+			compatible = "arm,cortex-a53","arm,armv8";
+			reg = <0x0 0x100>;
+			device_type = "cpu";
+			enable-method = "psci";
+		};
+
+		.....
+	};
+
+};

Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt

@@ -1,8 +1,35 @@
 Broadcom BCM2835 device tree bindings
 -------------------------------------------
 
-Boards with the BCM2835 SoC shall have the following properties:
+Raspberry Pi Model A
+Required root node properties:
+compatible = "raspberrypi,model-a", "brcm,bcm2835";
 
-Required root node property:
+Raspberry Pi Model A+
+Required root node properties:
+compatible = "raspberrypi,model-a-plus", "brcm,bcm2835";
 
+Raspberry Pi Model B
+Required root node properties:
+compatible = "raspberrypi,model-b", "brcm,bcm2835";
+
+Raspberry Pi Model B (no P5)
+early model B with I2C0 rather than I2C1 routed to the expansion header
+Required root node properties:
+compatible = "raspberrypi,model-b-i2c0", "brcm,bcm2835";
+
+Raspberry Pi Model B rev2
+Required root node properties:
+compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835";
+
+Raspberry Pi Model B+
+Required root node properties:
+compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
+
+Raspberry Pi Compute Module
+Required root node properties:
+compatible = "raspberrypi,compute-module", "brcm,bcm2835";
+
+Generic BCM2835 board
+Required root node properties:
 compatible = "brcm,bcm2835";

Documentation/devicetree/bindings/arm/bcm/brcm,bcm63138.txt

@@ -7,3 +7,79 @@ following properties:
 Required root node property:
 
 compatible: should be "brcm,bcm63138"
+
+An optional Boot lookup table Device Tree node is required for secondary CPU
+initialization as well as a 'resets' phandle to the correct PMB controller as
+defined in reset/brcm,bcm63138-pmb.txt for this secondary CPU, and an
+'enable-method' property.
+
+Required properties for the Boot lookup table node:
+- compatible: should be "brcm,bcm63138-bootlut"
+- reg: register base address and length for the Boot Lookup table
+
+Optional properties for the primary CPU node:
+- enable-method: should be "brcm,bcm63138"
+
+Optional properties for the secondary CPU node:
+- enable-method: should be "brcm,bcm63138"
+- resets: phandle to the relevant PMB controller, one integer indicating the internal
+  bus number, and a second integer indicating the address of the CPU in the PMB
+  internal bus number.
+
+Example:
+
+	cpus {
+		cpu@0 {
+			compatible = "arm,cotex-a9";
+			reg = <0>;
+			...
+			enable-method = "brcm,bcm63138";
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a9";
+			reg = <1>;
+			...
+			enable-method = "brcm,bcm63138";
+			resets = <&pmb0 4 1>;
+		};
+	};
+
+	bootlut: bootlut@8000 {
+		compatible = "brcm,bcm63138-bootlut";
+		reg = <0x8000 0x50>;
+	};
+
+=======
+reboot
+------
+Two nodes are required for software reboot: a timer node and a syscon-reboot node.
+
+Timer node:
+
+- compatible: Must be "brcm,bcm6328-timer", "syscon"
+- reg: Register base address and length
+
+Syscon reboot node:
+
+See Documentation/devicetree/bindings/power/reset/syscon-reboot.txt for the
+detailed list of properties, the two values defined below are specific to the
+BCM6328-style timer:
+
+- offset: Should be 0x34 to denote the offset of the TIMER_WD_TIMER_RESET register
+  from the beginning of the TIMER block
+- mask: Should be 1 for the SoftRst bit.
+
+Example:
+
+	timer: timer@80 {
+		compatible = "brcm,bcm6328-timer", "syscon";
+		reg = <0x80 0x3c>;
+	};
+
+	reboot {
+		compatible = "syscon-reboot";
+		regmap = <&timer>;
+		offset = <0x34>;
+		mask = <0x1>;
+	};

Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt

@@ -1,5 +1,8 @@
 Hisilicon Platforms Device Tree Bindings
 ----------------------------------------------------
+Hi6220 SoC
+Required root node properties:
+	- compatible = "hisilicon,hi6220";
 
 Hi4511 Board
 Required root node properties:
@@ -13,6 +16,9 @@ HiP01 ca9x2 Board
 Required root node properties:
 	- compatible = "hisilicon,hip01-ca9x2";
 
+HiKey Board
+Required root node properties:
+	- compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220";
 
 Hisilicon system controller
 
@@ -40,6 +46,87 @@ Example:
 		reboot-offset = <0x4>;
 	};
 
+-----------------------------------------------------------------------
+Hisilicon Hi6220 system controller
+
+Required properties:
+- compatible : "hisilicon,hi6220-sysctrl"
+- reg : Register address and size
+- #clock-cells: should be set to 1, many clock registers are defined
+  under this controller and this property must be present.
+
+Hisilicon designs this controller as one of the system controllers,
+its main functions are the same as Hisilicon system controller, but
+the register offset of some core modules are different.
+
+Example:
+	/*for Hi6220*/
+	sys_ctrl: sys_ctrl@f7030000 {
+		compatible = "hisilicon,hi6220-sysctrl", "syscon";
+		reg = <0x0 0xf7030000 0x0 0x2000>;
+		#clock-cells = <1>;
+	};
+
+
+Hisilicon Hi6220 Power Always ON domain controller
+
+Required properties:
+- compatible : "hisilicon,hi6220-aoctrl"
+- reg : Register address and size
+- #clock-cells: should be set to 1, many clock registers are defined
+  under this controller and this property must be present.
+
+Hisilicon designs this system controller to control the power always
+on domain for mobile platform.
+
+Example:
+	/*for Hi6220*/
+	ao_ctrl: ao_ctrl@f7800000 {
+		compatible = "hisilicon,hi6220-aoctrl", "syscon";
+		reg = <0x0 0xf7800000 0x0 0x2000>;
+		#clock-cells = <1>;
+	};
+
+
+Hisilicon Hi6220 Media domain controller
+
+Required properties:
+- compatible : "hisilicon,hi6220-mediactrl"
+- reg : Register address and size
+- #clock-cells: should be set to 1, many clock registers are defined
+  under this controller and this property must be present.
+
+Hisilicon designs this system controller to control the multimedia
+domain(e.g. codec, G3D ...) for mobile platform.
+
+Example:
+	/*for Hi6220*/
+	media_ctrl: media_ctrl@f4410000 {
+		compatible = "hisilicon,hi6220-mediactrl", "syscon";
+		reg = <0x0 0xf4410000 0x0 0x1000>;
+		#clock-cells = <1>;
+	};
+
+
+Hisilicon Hi6220 Power Management domain controller
+
+Required properties:
+- compatible : "hisilicon,hi6220-pmctrl"
+- reg : Register address and size
+- #clock-cells: should be set to 1, some clock registers are define
+  under this controller and this property must be present.
+
+Hisilicon designs this system controller to control the power management
+domain for mobile platform.
+
+Example:
+	/*for Hi6220*/
+	pm_ctrl: pm_ctrl@f7032000 {
+		compatible = "hisilicon,hi6220-pmctrl", "syscon";
+		reg = <0x0 0xf7032000 0x0 0x1000>;
+		#clock-cells = <1>;
+	};
+
 -----------------------------------------------------------------------
 Hisilicon HiP01 system controller
 

Documentation/devicetree/bindings/arm/marvell,berlin.txt

@@ -1,6 +1,18 @@
 Marvell Berlin SoC Family Device Tree Bindings
 ---------------------------------------------------------------
 
+Work in progress statement:
+
+Device tree files and bindings applying to Marvell Berlin SoCs and boards are
+considered "unstable". Any Marvell Berlin device tree binding may change at any
+time. Be sure to use a device tree binary and a kernel image generated from the
+same source tree.
+
+Please refer to Documentation/devicetree/bindings/ABI.txt for a definition of a
+stable binding/ABI.
+
+---------------------------------------------------------------
+
 Boards with a SoC of the Marvell Berlin family, e.g. Armada 1500
 shall have the following properties:
 
@@ -49,10 +61,9 @@ chip control registers, so there should be a single DT node only providing the
 different functions which are described below.
 
 Required properties:
-- compatible: shall be one of
-	"marvell,berlin2-chip-ctrl" for BG2
-	"marvell,berlin2cd-chip-ctrl" for BG2CD
-	"marvell,berlin2q-chip-ctrl" for BG2Q
+- compatible:
+	* the first and second values must be:
+		"simple-mfd", "syscon"
 - reg: address and length of following register sets for
   BG2/BG2CD: chip control register set
   BG2Q: chip control register set and cpu pll registers
@@ -63,90 +74,23 @@ Marvell Berlin SoCs have a system control register set providing several
 individual registers dealing with pinmux, padmux, and reset.
 
 Required properties:
-- compatible: should be one of
-	"marvell,berlin2-system-ctrl" for BG2
-	"marvell,berlin2cd-system-ctrl" for BG2CD
-	"marvell,berlin2q-system-ctrl" for BG2Q
+- compatible:
+	* the first and second values must be:
+		"simple-mfd", "syscon"
 - reg: address and length of the system control register set
 
-* Clock provider binding
-
-As clock related registers are spread among the chip control registers, the
-chip control node also provides the clocks. Marvell Berlin2 (BG2, BG2CD, BG2Q)
-SoCs share the same IP for PLLs and clocks, with some minor differences in
-features and register layout.
-
-Required properties:
-- #clock-cells: shall be set to 1
-- clocks: clock specifiers referencing the core clock input clocks
-- clock-names: array of strings describing the input clock specifiers above.
-    Allowed clock-names for the reference clocks are
-      "refclk" for the SoCs osciallator input on all SoCs,
-    and SoC-specific input clocks for
-      BG2/BG2CD: "video_ext0" for the external video clock input
-
-Clocks provided by core clocks shall be referenced by a clock specifier
-indexing one of the provided clocks. Refer to dt-bindings/clock/berlin<soc>.h
-for the corresponding index mapping.
-
-* Pin controller binding
-
-Pin control registers are part of both register sets, chip control and system
-control. The pins controlled are organized in groups, so no actual pin
-information is needed.
-
-A pin-controller node should contain subnodes representing the pin group
-configurations, one per function. Each subnode has the group name and the muxing
-function used.
-
-Be aware the Marvell Berlin datasheets use the keyword 'mode' for what is called
-a 'function' in the pin-controller subsystem.
-
-Required subnode-properties:
-- groups: a list of strings describing the group names.
-- function: a string describing the function used to mux the groups.
-
-* Reset controller binding
-
-A reset controller is part of the chip control registers set. The chip control
-node also provides the reset. The register set is not at the same offset between
-Berlin SoCs.
-
-Required property:
-- #reset-cells: must be set to 2
-
 Example:
 
 chip: chip-control@ea0000 {
-	compatible = "marvell,berlin2-chip-ctrl";
-	#clock-cells = <1>;
-	#reset-cells = <2>;
+	compatible = "simple-mfd", "syscon";
 	reg = <0xea0000 0x400>;
-	clocks = <&refclk>, <&externaldev 0>;
-	clock-names = "refclk", "video_ext0";
 
-	spi1_pmux: spi1-pmux {
-		groups = "G0";
-		function = "spi1";
-	};
+	/* sub-device nodes */
 };
 
 sysctrl: system-controller@d000 {
-	compatible = "marvell,berlin2-system-ctrl";
+	compatible = "simple-mfd", "syscon";
 	reg = <0xd000 0x100>;
 
-	uart0_pmux: uart0-pmux {
-		groups = "GSM4";
-		function = "uart0";
-	};
-
-	uart1_pmux: uart1-pmux {
-		groups = "GSM5";
-		function = "uart1";
-	};
-
-	uart2_pmux: uart2-pmux {
-		groups = "GSM3";
-		function = "uart2";
-	};
+	/* sub-device nodes */
 };

Documentation/devicetree/bindings/arm/scu.txt

@@ -0,0 +1,25 @@
+* ARM Snoop Control Unit (SCU)
+
+As part of the MPCore complex, Cortex-A5 and Cortex-A9 are provided
+with a Snoop Control Unit. The register range is usually 256 (0x100)
+bytes.
+
+References:
+
+- Cortex-A9: see DDI0407E Cortex-A9 MPCore Technical Reference Manual
+  Revision r2p0
+- Cortex-A5: see DDI0434B Cortex-A5 MPCore Technical Reference Manual
+  Revision r0p1
+
+- compatible : Should be:
+	"arm,cortex-a9-scu"
+	"arm,cortex-a5-scu"
+
+- reg : Specify the base address and the size of the SCU register window.
+
+Example:
+
+scu@a04100000 {
+	compatible = "arm,cortex-a9-scu";
+	reg = <0xa0410000 0x100>;
+};

Documentation/devicetree/bindings/arm/ux500/boards.txt

@@ -0,0 +1,83 @@
+ST-Ericsson Ux500 boards
+------------------------
+
+Required properties (in root node) one of these:
+	compatible = "st-ericsson,mop500" (legacy)
+	compatible = "st-ericsson,u8500"
+
+Required node (under root node):
+
+soc: represents the system-on-chip and contains the chip
+peripherals
+
+Required property of soc node, one of these:
+	compatible = "stericsson,db8500"
+
+Required subnodes under soc node:
+
+backupram: (used for CPU spin tables and for storing data
+during retention, system won't boot without this):
+	compatible = "ste,dbx500-backupram"
+
+scu:
+	see binding for arm/scu.txt
+
+interrupt-controller:
+	see binding for arm/gic.txt
+
+timer:
+	see binding for arm/twd.txt
+
+clocks:
+	see binding for clocks/ux500.txt
+
+Example:
+
+/dts-v1/;
+
+/ {
+        model = "ST-Ericsson HREF (pre-v60) and ST UIB";
+        compatible = "st-ericsson,mop500", "st-ericsson,u8500";
+
+        soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "stericsson,db8500";
+		interrupt-parent = <&intc>;
+		ranges;
+
+		backupram@80150000 {
+			compatible = "ste,dbx500-backupram";
+			reg = <0x80150000 0x2000>;
+		};
+
+		intc: interrupt-controller@a0411000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <1>;
+			interrupt-controller;
+			reg = <0xa0411000 0x1000>,
+			      <0xa0410100 0x100>;
+		};
+
+		scu@a04100000 {
+			compatible = "arm,cortex-a9-scu";
+			reg = <0xa0410000 0x100>;
+		};
+
+		timer@a0410600 {
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = <0xa0410600 0x20>;
+			interrupts = <1 13 0x304>; /* IRQ level high per-CPU */
+			clocks = <&smp_twd_clk>;
+		};
+
+		clocks {
+			compatible = "stericsson,u8500-clks";
+
+			smp_twd_clk: smp-twd-clock {
+				#clock-cells = <0>;
+			};
+		};
+        };
+};

Documentation/devicetree/bindings/clock/hi6220-clock.txt

@@ -0,0 +1,34 @@
+* Hisilicon Hi6220 Clock Controller
+
+Clock control registers reside in different Hi6220 system controllers,
+please refer the following document to know more about the binding rules
+for these system controllers:
+
+Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
+
+Required Properties:
+
+- compatible: the compatible should be one of the following strings to
+	indicate the clock controller functionality.
+
+	- "hisilicon,hi6220-aoctrl"
+	- "hisilicon,hi6220-sysctrl"
+	- "hisilicon,hi6220-mediactrl"
+	- "hisilicon,hi6220-pmctrl"
+
+- reg: physical base address of the controller and length of memory mapped
+  region.
+
+- #clock-cells: should be 1.
+
+For example:
+	sys_ctrl: sys_ctrl@f7030000 {
+		compatible = "hisilicon,hi6220-sysctrl", "syscon";
+		reg = <0x0 0xf7030000 0x0 0x2000>;
+		#clock-cells = <1>;
+	};
+
+Each clock is assigned an identifier and client nodes use this identifier
+to specify the clock which they consume.
+
+All these identifier could be found in <dt-bindings/clock/hi6220-clock.h>.

Documentation/devicetree/bindings/clock/imx7d-clock.txt

@@ -0,0 +1,13 @@
+* Clock bindings for Freescale i.MX7 Dual
+
+Required properties:
+- compatible: Should be "fsl,imx7d-ccm"
+- reg: Address and length of the register set
+- #clock-cells: Should be <1>
+- clocks: list of clock specifiers, must contain an entry for each required
+  entry in clock-names
+- clock-names: should include entries "ckil", "osc"
+
+The clock consumer should specify the desired clock by having the clock
+ID in its "clocks" phandle cell.  See include/dt-bindings/clock/imx7d-clock.h
+for the full list of i.MX7 Dual clock IDs.

Documentation/devicetree/bindings/clock/marvell,berlin.txt

@@ -0,0 +1,31 @@
+Device Tree Clock bindings for Marvell Berlin
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Clock related registers are spread among the chip control registers. Berlin
+clock node should be a sub-node of the chip controller node. Marvell Berlin2
+(BG2, BG2CD, BG2Q) SoCs share the same IP for PLLs and clocks, with some
+minor differences in features and register layout.
+
+Required properties:
+- compatible: must be "marvell,berlin2-clk" or "marvell,berlin2q-clk"
+- #clock-cells: must be 1
+- clocks: must be the input parent clock phandle
+- clock-names: name of the input parent clock
+	Allowed clock-names for the reference clocks are
+	"refclk" for the SoCs oscillator input on all SoCs,
+	and SoC-specific input clocks for
+	BG2/BG2CD: "video_ext0" for the external video clock input
+
+
+Example:
+
+chip_clk: clock {
+	compatible = "marvell,berlin2q-clk";
+
+	#clock-cells = <1>;
+	clocks = <&refclk>;
+	clock-names = "refclk";
+};

Documentation/devicetree/bindings/pci/xilinx-pcie.txt

@@ -58,5 +58,5 @@ Example:
 			interrupt-controller;
 			#address-cells = <0>;
 			#interrupt-cells = <1>;
-		}
+		};
 	};

Documentation/devicetree/bindings/pinctrl/berlin,pinctrl.txt

@@ -0,0 +1,43 @@
+* Pin-controller driver for the Marvell Berlin SoCs
+
+Pin control registers are part of both chip controller and system
+controller register sets. Pin controller nodes should be a sub-node of
+either the chip controller or system controller node. The pins
+controlled are organized in groups, so no actual pin information is
+needed.
+
+A pin-controller node should contain subnodes representing the pin group
+configurations, one per function. Each subnode has the group name and
+the muxing function used.
+
+Be aware the Marvell Berlin datasheets use the keyword 'mode' for what
+is called a 'function' in the pin-controller subsystem.
+
+Required properties:
+- compatible: should be one of:
+	"marvell,berlin2-soc-pinctrl",
+	"marvell,berlin2-system-pinctrl",
+	"marvell,berlin2cd-soc-pinctrl",
+	"marvell,berlin2cd-system-pinctrl",
+	"marvell,berlin2q-soc-pinctrl",
+	"marvell,berlin2q-system-pinctrl"
+
+Required subnode-properties:
+- groups: a list of strings describing the group names.
+- function: a string describing the function used to mux the groups.
+
+Example:
+
+sys_pinctrl: pin-controller {
+	compatible = "marvell,berlin2q-system-pinctrl";
+
+	uart0_pmux: uart0-pmux {
+		groups = "GSM12";
+		function = "uart0";
+	};
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pmux>;
+	pinctrl-names = "default";
+};

Documentation/devicetree/bindings/pinctrl/fsl,imx7d-pinctrl.txt

@@ -0,0 +1,27 @@
+* Freescale i.MX7 Dual IOMUX Controller
+
+Please refer to fsl,imx-pinctrl.txt in this directory for common binding part
+and usage.
+
+Required properties:
+- compatible: "fsl,imx7d-iomuxc"
+- fsl,pins: each entry consists of 6 integers and represents the mux and config
+  setting for one pin.  The first 5 integers <mux_reg conf_reg input_reg mux_val
+  input_val> are specified using a PIN_FUNC_ID macro, which can be found in
+  imx7d-pinfunc.h under device tree source folder.  The last integer CONFIG is
+  the pad setting value like pull-up on this pin.  Please refer to i.MX7 Dual
+  Reference Manual for detailed CONFIG settings.
+
+CONFIG bits definition:
+PAD_CTL_PUS_100K_DOWN           (0 << 5)
+PAD_CTL_PUS_5K_UP               (1 << 5)
+PAD_CTL_PUS_47K_UP              (2 << 5)
+PAD_CTL_PUS_100K_UP             (3 << 5)
+PAD_CTL_PUE                     (1 << 4)
+PAD_CTL_HYS                     (1 << 3)
+PAD_CTL_SRE_SLOW                (1 << 2)
+PAD_CTL_SRE_FAST                (0 << 2)
+PAD_CTL_DSE_X1                  (0 << 0)
+PAD_CTL_DSE_X2                  (1 << 0)
+PAD_CTL_DSE_X3                  (2 << 0)
+PAD_CTL_DSE_X4                  (3 << 0)

Documentation/devicetree/bindings/reset/berlin,reset.txt

@@ -0,0 +1,23 @@
+Marvell Berlin reset controller
+===============================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+The reset controller node must be a sub-node of the chip controller
+node on Berlin SoCs.
+
+Required properties:
+- compatible: should be "marvell,berlin2-reset"
+- #reset-cells: must be set to 2
+
+Example:
+
+chip_rst: reset {
+	compatible = "marvell,berlin2-reset";
+	#reset-cells = <2>;
+};
+
+&usb_phy0 {
+	resets = <&chip_rst 0x104 12>;
+};

Documentation/devicetree/bindings/reset/brcm,bcm63138-pmb.txt

@@ -0,0 +1,19 @@
+Broadcom BCM63138 Processor Monitor Bus binding
+===============================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Require properties:
+
+- compatible: must be "brcm,bcm63138-pmb"
+- reg: base register address and size for this bus controller
+- #reset-cells: must be 2 first cell is the address within the bus instance designated
+  by the phandle, and the second is the number of zones for this peripheral
+
+Example:
+	pmb0: reset-controller@4800c0 {
+		compatible = "brcm,bcm63138-pmb";
+		reg = <0x4800c0 0x10>;
+		#reset-cells = <2>;
+	};

Documentation/devicetree/bindings/rtc/s3c-rtc.txt

@@ -6,7 +6,8 @@ Required properties:
     * "samsung,s3c2416-rtc" - for controllers compatible with s3c2416 rtc.
     * "samsung,s3c2443-rtc" - for controllers compatible with s3c2443 rtc.
     * "samsung,s3c6410-rtc" - for controllers compatible with s3c6410 rtc.
-    * "samsung,exynos3250-rtc" - for controllers compatible with exynos3250 rtc.
+    * "samsung,exynos3250-rtc" - (deprecated) for controllers compatible with
+                                 exynos3250 rtc (use "samsung,s3c6410-rtc").
 - reg: physical base address of the controller and length of memory mapped
   region.
 - interrupts: Two interrupt numbers to the cpu should be specified. First

Documentation/devicetree/bindings/spi/sh-msiof.txt

@@ -60,7 +60,7 @@ Example:
 
 	msiof0: spi@e6e20000 {
 		compatible = "renesas,msiof-r8a7791";
-		reg = <0 0xe6e20000 0 0x0064>, <0 0xe7e20000 0 0x0064>;
+		reg = <0 0xe6e20000 0 0x0064>;
 		interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>;
 		dmas = <&dmac0 0x51>, <&dmac0 0x52>;

Documentation/devicetree/bindings/timer/cadence,ttc-timer.txt

@@ -6,6 +6,9 @@ Required properties:
 - interrupts : A list of 3 interrupts; one per timer channel.
 - clocks: phandle to the source clock
 
+Optional properties:
+- timer-width: Bit width of the timer, necessary if not 16.
+
 Example:
 
 ttc0: ttc0@f8001000 {
@@ -14,4 +17,5 @@ ttc0: ttc0@f8001000 {
 	compatible = "cdns,ttc";
 	reg = <0xF8001000 0x1000>;
 	clocks = <&cpu_clk 3>;
+	timer-width = <32>;
 };

Documentation/devicetree/bindings/usb/atmel-usb.txt

@@ -5,6 +5,13 @@ OHCI
 Required properties:
  - compatible: Should be "atmel,at91rm9200-ohci" for USB controllers
    used in host mode.
+ - reg: Address and length of the register set for the device
+ - interrupts: Should contain ehci interrupt
+ - clocks: Should reference the peripheral, host and system clocks
+ - clock-names: Should contains two strings
+		"ohci_clk" for the peripheral clock
+		"hclk" for the host clock
+		"uhpck" for the system clock
  - num-ports: Number of ports.
  - atmel,vbus-gpio: If present, specifies a gpio that needs to be
    activated for the bus to be powered.
@@ -14,6 +21,8 @@ Required properties:
 usb0: ohci@00500000 {
 	compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 	reg = <0x00500000 0x100000>;
+	clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+	clock-names = "ohci_clk", "hclk", "uhpck";
 	interrupts = <20 4>;
 	num-ports = <2>;
 };
@@ -23,11 +32,19 @@ EHCI
 Required properties:
  - compatible: Should be "atmel,at91sam9g45-ehci" for USB controllers
    used in host mode.
+ - reg: Address and length of the register set for the device
+ - interrupts: Should contain ehci interrupt
+ - clocks: Should reference the peripheral and the UTMI clocks
+ - clock-names: Should contains two strings
+		"ehci_clk" for the peripheral clock
+		"usb_clk" for the UTMI clock
 
 usb1: ehci@00800000 {
 	compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 	reg = <0x00800000 0x100000>;
 	interrupts = <22 4>;
+	clocks = <&utmi>, <&uhphs_clk>;
+	clock-names = "usb_clk", "ehci_clk";
 };
 
 AT91 USB device controller
@@ -53,6 +70,8 @@ usb1: gadget@fffa4000 {
 	compatible = "atmel,at91rm9200-udc";
 	reg = <0xfffa4000 0x4000>;
 	interrupts = <10 4>;
+	clocks = <&udc_clk>, <&udpck>;
+	clock-names = "pclk", "hclk";
 	atmel,vbus-gpio = <&pioC 5 0>;
 };
 
@@ -65,6 +84,10 @@ Required properties:
 	       "sama5d3-udc"
  - reg: Address and length of the register set for the device
  - interrupts: Should contain usba interrupt
+ - clocks: Should reference the peripheral and host clocks
+ - clock-names: Should contains two strings
+		"pclk" for the peripheral clock
+		"hclk" for the host clock
  - ep childnode: To specify the number of endpoints and their properties.
 
 Optional properties:
@@ -86,6 +109,8 @@ usb2: gadget@fff78000 {
 	reg = <0x00600000 0x80000
 	       0xfff78000 0x400>;
 	interrupts = <27 4 0>;
+	clocks = <&utmi>, <&udphs_clk>;
+	clock-names = "hclk", "pclk";
 	atmel,vbus-gpio = <&pioB 19 0>;
 
 	ep0 {

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -40,6 +40,7 @@ calxeda	Calxeda
 capella	Capella Microsystems, Inc
 cavium	Cavium, Inc.
 cdns	Cadence Design Systems Inc.
+ceva	Ceva, Inc.
 chipidea	Chipidea, Inc
 chipone		ChipOne
 chipspark	ChipSPARK
@@ -52,6 +53,7 @@ cnxt	Conexant Systems, Inc.
 cortina	Cortina Systems, Inc.
 cosmic	Cosmic Circuits
 crystalfontz	Crystalfontz America, Inc.
+cubietech	Cubietech, Ltd.
 dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
 davicom	DAVICOM Semiconductor, Inc.
 delta	Delta Electronics, Inc.
@@ -61,6 +63,7 @@ digilent	Diglent, Inc.
 dlg	Dialog Semiconductor
 dlink	D-Link Corporation
 dmo	Data Modul AG
+ea	Embedded Artists AB
 ebv	EBV Elektronik
 edt	Emerging Display Technologies
 elan	Elan Microelectronic Corp.
@@ -91,9 +94,11 @@ gumstix	Gumstix, Inc.
 gw	Gateworks Corporation
 hannstar	HannStar Display Corporation
 haoyu	Haoyu Microelectronic Co. Ltd.
+hardkernel	Hardkernel Co., Ltd
 himax	Himax Technologies, Inc.
 hisilicon	Hisilicon Limited.
 hit	Hitachi Ltd.
+hitex	Hitex Development Tools
 honeywell	Honeywell
 hp	Hewlett Packard
 i2se	I2SE GmbH
@@ -160,6 +165,7 @@ radxa	Radxa
 raidsonic	RaidSonic Technology GmbH
 ralink	Mediatek/Ralink Technology Corp.
 ramtron	Ramtron International
+raspberrypi	Raspberry Pi Foundation
 realtek Realtek Semiconductor Corp.
 renesas	Renesas Electronics Corporation
 richtek	Richtek Technology Corporation
@@ -192,6 +198,7 @@ ste	ST-Ericsson
 stericsson	ST-Ericsson
 synology	Synology, Inc.
 tbs	TBS Technologies
+tcl	Toby Churchill Ltd.
 thine	THine Electronics, Inc.
 ti	Texas Instruments
 tlm	Trusted Logic Mobility
@@ -205,6 +212,7 @@ variscite	Variscite Ltd.
 via	VIA Technologies, Inc.
 virtio	Virtual I/O Device Specification, developed by the OASIS consortium
 voipac	Voipac Technologies s.r.o.
+wexler	Wexler
 winbond Winbond Electronics corp.
 wlf	Wolfson Microelectronics
 wm	Wondermedia Technologies, Inc.

arch/arm/boot/dts/Makefile

@@ -20,9 +20,9 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
 	tny_a9263.dtb \
 	usb_a9263.dtb \
 	at91-foxg20.dtb \
+	at91-kizbox.dtb \
 	at91sam9g20ek.dtb \
 	at91sam9g20ek_2mmc.dtb \
-	kizbox.dtb \
 	tny_a9g20.dtb \
 	usb_a9g20.dtb \
 	usb_a9g20_lpw.dtb \
@@ -31,13 +31,16 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
 	at91sam9n12ek.dtb \
 	at91sam9rlek.dtb \
 	at91-ariag25.dtb \
+	at91-ariettag25.dtb \
 	at91-cosino_mega2560.dtb \
+	at91-kizboxmini.dtb \
 	at91sam9g15ek.dtb \
 	at91sam9g25ek.dtb \
 	at91sam9g35ek.dtb \
 	at91sam9x25ek.dtb \
 	at91sam9x35ek.dtb
 dtb-$(CONFIG_SOC_SAM_V7) += \
+	at91-kizbox2.dtb \
 	at91-sama5d3_xplained.dtb \
 	sama5d31ek.dtb \
 	sama5d33ek.dtb \
@@ -56,13 +59,18 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2835-rpi-b.dtb \
 	bcm2835-rpi-b-plus.dtb
 dtb-$(CONFIG_ARCH_BCM_5301X) += \
+	bcm4708-asus-rt-ac56u.dtb \
+	bcm4708-asus-rt-ac68u.dtb \
 	bcm4708-buffalo-wzr-1750dhp.dtb \
 	bcm4708-luxul-xwc-1000.dtb \
 	bcm4708-netgear-r6250.dtb \
 	bcm4708-netgear-r6300-v2.dtb \
+	bcm4708-smartrg-sr400ac.dtb \
 	bcm47081-asus-rt-n18u.dtb \
 	bcm47081-buffalo-wzr-600dhp2.dtb \
 	bcm47081-buffalo-wzr-900dhp.dtb \
+	bcm4709-asus-rt-ac87u.dtb \
+	bcm4709-buffalo-wxr-1900dhp.dtb \
 	bcm4709-netgear-r8000.dtb
 dtb-$(CONFIG_ARCH_BCM_63XX) += \
 	bcm963138dvt.dtb
@@ -113,6 +121,7 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \
 	exynos5420-peach-pit.dtb \
 	exynos5420-smdk5420.dtb \
 	exynos5422-odroidxu3.dtb \
+	exynos5422-odroidxu3-lite.dtb \
 	exynos5440-sd5v1.dtb \
 	exynos5440-ssdk5440.dtb \
 	exynos5800-peach-pi.dtb
@@ -201,6 +210,9 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
 	kirkwood-ts219-6282.dtb \
 	kirkwood-ts419-6281.dtb \
 	kirkwood-ts419-6282.dtb
+dtb-$(CONFIG_ARCH_LPC18XX) += \
+	lpc4350-hitex-eval.dtb \
+	lpc4357-ea4357-devkit.dtb
 dtb-$(CONFIG_ARCH_LPC32XX) += \
 	ea3250.dtb phy3250.dtb
 dtb-$(CONFIG_MACH_MESON6) += \
@@ -254,14 +266,18 @@ dtb-$(CONFIG_SOC_IMX53) += \
 	imx53-tx53-x13x.dtb \
 	imx53-voipac-bsb.dtb
 dtb-$(CONFIG_SOC_IMX6Q) += \
+	imx6dl-apf6dev.dtb \
 	imx6dl-aristainetos_4.dtb \
 	imx6dl-aristainetos_7.dtb \
+	imx6dl-aristainetos2_4.dtb \
+	imx6dl-aristainetos2_7.dtb \
 	imx6dl-cubox-i.dtb \
 	imx6dl-dfi-fs700-m60.dtb \
 	imx6dl-gw51xx.dtb \
 	imx6dl-gw52xx.dtb \
 	imx6dl-gw53xx.dtb \
 	imx6dl-gw54xx.dtb \
+	imx6dl-gw551x.dtb \
 	imx6dl-gw552x.dtb \
 	imx6dl-hummingboard.dtb \
 	imx6dl-nitrogen6x.dtb \
@@ -277,6 +293,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-udoo.dtb \
 	imx6dl-wandboard.dtb \
 	imx6dl-wandboard-revb1.dtb \
+	imx6q-apf6dev.dtb \
 	imx6q-arm2.dtb \
 	imx6q-cm-fx6.dtb \
 	imx6q-cubox-i.dtb \
@@ -288,6 +305,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-gw53xx.dtb \
 	imx6q-gw5400-a.dtb \
 	imx6q-gw54xx.dtb \
+	imx6q-gw551x.dtb \
 	imx6q-gw552x.dtb \
 	imx6q-hummingboard.dtb \
 	imx6q-nitrogen6x.dtb \
@@ -313,12 +331,15 @@ dtb-$(CONFIG_SOC_IMX6SX) += \
 	imx6sx-sabreauto.dtb \
 	imx6sx-sdb-reva.dtb \
 	imx6sx-sdb.dtb
+dtb-$(CONFIG_SOC_IMX7D) += \
+	imx7d-sdb.dtb
 dtb-$(CONFIG_SOC_LS1021A) += \
 	ls1021a-qds.dtb \
 	ls1021a-twr.dtb
 dtb-$(CONFIG_SOC_VF610) += \
 	vf500-colibri-eval-v3.dtb \
 	vf610-colibri-eval-v3.dtb \
+	vf610m4-colibri.dtb \
 	vf610-cosmic.dtb \
 	vf610-twr.dtb
 dtb-$(CONFIG_ARCH_MXS) += \
@@ -360,6 +381,7 @@ dtb-$(CONFIG_ARCH_OMAP3) += \
 	am3517-craneboard.dtb \
 	am3517-evm.dtb \
 	am3517_mt_ventoux.dtb \
+	logicpd-torpedo-37xx-devkit.dtb \
 	omap3430-sdp.dtb \
 	omap3-beagle.dtb \
 	omap3-beagle-xm.dtb \
@@ -406,9 +428,11 @@ dtb-$(CONFIG_ARCH_OMAP3) += \
 dtb-$(CONFIG_SOC_TI81XX) += \
 	dm8168-evm.dtb
 dtb-$(CONFIG_SOC_AM33XX) += \
+	am335x-baltos-ir5221.dtb \
 	am335x-base0033.dtb \
 	am335x-bone.dtb \
 	am335x-boneblack.dtb \
+	am335x-sl50.dtb \
 	am335x-evm.dtb \
 	am335x-evmsk.dtb \
 	am335x-nano.dtb \
@@ -496,7 +520,7 @@ dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \
 	sh73a0-kzm9g.dtb
 dtb-$(CONFIG_ARCH_SOCFPGA) += \
 	socfpga_arria5_socdk.dtb \
-	socfpga_arria10_socdk.dtb \
+	socfpga_arria10_socdk_sdmmc.dtb \
 	socfpga_cyclone5_socdk.dtb \
 	socfpga_cyclone5_sockit.dtb \
 	socfpga_cyclone5_socrates.dtb \
@@ -520,32 +544,39 @@ dtb-$(CONFIG_ARCH_STI) += \
 	stih416-b2020.dtb \
 	stih416-b2020e.dtb \
 	stih418-b2199.dtb
+dtb-$(CONFIG_ARCH_STM32)+= stm32f429-disco.dtb
 dtb-$(CONFIG_MACH_SUN4I) += \
 	sun4i-a10-a1000.dtb \
 	sun4i-a10-ba10-tvbox.dtb \
 	sun4i-a10-chuwi-v7-cw0825.dtb \
 	sun4i-a10-cubieboard.dtb \
+	sun4i-a10-gemei-g9.dtb \
+	sun4i-a10-hackberry.dtb \
+	sun4i-a10-hyundai-a7hd.dtb \
+	sun4i-a10-inet97fv2.dtb \
+	sun4i-a10-jesurun-q5.dtb \
 	sun4i-a10-marsboard.dtb \
 	sun4i-a10-mini-xplus.dtb \
 	sun4i-a10-mk802.dtb \
 	sun4i-a10-mk802ii.dtb \
-	sun4i-a10-hackberry.dtb \
-	sun4i-a10-hyundai-a7hd.dtb \
-	sun4i-a10-inet97fv2.dtb \
 	sun4i-a10-olinuxino-lime.dtb \
 	sun4i-a10-pcduino.dtb
 dtb-$(CONFIG_MACH_SUN5I) += \
+	sun5i-a10s-auxtek-t004.dtb \
 	sun5i-a10s-mk802.dtb \
 	sun5i-a10s-olinuxino-micro.dtb \
 	sun5i-a10s-r7-tv-dongle.dtb \
 	sun5i-a13-hsg-h702.dtb \
 	sun5i-a13-olinuxino.dtb \
-	sun5i-a13-olinuxino-micro.dtb
+	sun5i-a13-olinuxino-micro.dtb \
+	sun5i-a13-utoo-p66.dtb
 dtb-$(CONFIG_MACH_SUN6I) += \
 	sun6i-a31-app4-evb1.dtb \
 	sun6i-a31-colombus.dtb \
 	sun6i-a31-hummingbird.dtb \
+	sun6i-a31-i7.dtb \
 	sun6i-a31-m9.dtb \
+	sun6i-a31-mele-a1000g-quad.dtb \
 	sun6i-a31s-cs908.dtb
 dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-bananapi.dtb \
@@ -555,15 +586,25 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-hummingbird.dtb \
 	sun7i-a20-i12-tvbox.dtb \
 	sun7i-a20-m3.dtb \
+	sun7i-a20-mk808c.dtb \
 	sun7i-a20-olinuxino-lime.dtb \
 	sun7i-a20-olinuxino-lime2.dtb \
 	sun7i-a20-olinuxino-micro.dtb \
-	sun7i-a20-pcduino3.dtb
+	sun7i-a20-orangepi.dtb \
+	sun7i-a20-orangepi-mini.dtb \
+	sun7i-a20-pcduino3.dtb \
+	sun7i-a20-pcduino3-nano.dtb \
+	sun7i-a20-wexler-tab7200.dtb
 dtb-$(CONFIG_MACH_SUN8I) += \
+	sun8i-a23-evb.dtb \
 	sun8i-a23-ippo-q8h-v5.dtb \
-	sun8i-a23-ippo-q8h-v1.2.dtb
+	sun8i-a23-ippo-q8h-v1.2.dtb \
+	sun8i-a33-et-q8-v1.6.dtb \
+	sun8i-a33-ga10h-v1.1.dtb \
+	sun8i-a33-sinlinx-sina33.dtb
 dtb-$(CONFIG_MACH_SUN9I) += \
-	sun9i-a80-optimus.dtb
+	sun9i-a80-optimus.dtb \
+	sun9i-a80-cubieboard4.dtb
 dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \
 	tegra20-harmony.dtb \
 	tegra20-iris-512.dtb \
@@ -600,6 +641,11 @@ dtb-$(CONFIG_ARCH_U8500) += \
 	ste-hrefv60plus-tvk.dtb \
 	ste-ccu8540.dtb \
 	ste-ccu9540.dtb
+dtb-$(CONFIG_ARCH_UNIPHIER) += \
+	uniphier-ph1-sld3-ref.dtb \
+	uniphier-ph1-ld4-ref.dtb \
+	uniphier-ph1-pro4-ref.dtb \
+	uniphier-ph1-sld8-ref.dtb
 dtb-$(CONFIG_ARCH_VERSATILE) += \
 	versatile-ab.dtb \
 	versatile-pb.dtb
@@ -624,6 +670,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
 	zynq-zybo.dtb
 dtb-$(CONFIG_MACH_ARMADA_370) += \
 	armada-370-db.dtb \
+	armada-370-dlink-dns327l.dtb \
 	armada-370-mirabox.dtb \
 	armada-370-netgear-rn102.dtb \
 	armada-370-netgear-rn104.dtb \
@@ -633,6 +680,8 @@ dtb-$(CONFIG_MACH_ARMADA_375) += \
 	armada-375-db.dtb
 dtb-$(CONFIG_MACH_ARMADA_38X) += \
 	armada-385-db-ap.dtb \
+	armada-385-linksys-caiman.dtb \
+	armada-385-linksys-cobra.dtb \
 	armada-388-db.dtb \
 	armada-388-gp.dtb \
 	armada-388-rd.dtb
@@ -649,12 +698,12 @@ dtb-$(CONFIG_MACH_ARMADA_XP) += \
 	armada-xp-openblocks-ax3-4.dtb \
 	armada-xp-synology-ds414.dtb
 dtb-$(CONFIG_MACH_DOVE) += \
-	dove-cm-a510.dtb \
 	dove-cubox.dtb \
 	dove-cubox-es.dtb \
 	dove-d2plug.dtb \
 	dove-d3plug.dtb \
-	dove-dove-db.dtb
+	dove-dove-db.dtb \
+	dove-sbc-a510.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += \
 	mt6589-aquaris5.dtb \
 	mt6592-evb.dtb \

arch/arm/boot/dts/am335x-baltos-ir5221.dts

@@ -0,0 +1,532 @@
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * VScom OnRISC
+ * http://www.vscom.de
+ */
+
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "OnRISC Baltos iR 5221";
+	compatible = "vscom,onrisc", "ti,am33xx";
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vdd1_reg>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+
+	wl12xx_vmmc: fixedregulator@2 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wl12xx_gpio>;
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 8 0>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+};
+
+&am33xx_pinmux {
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			0x020 (PIN_INPUT_PULLUP | MUX_MODE2)      /* gpmc_ad8.mmc1_dat0_mux0 */
+			0x024 (PIN_INPUT_PULLUP | MUX_MODE2)      /* gpmc_ad9.mmc1_dat1_mux0 */
+			0x028 (PIN_INPUT_PULLUP | MUX_MODE2)      /* gpmc_ad10.mmc1_dat2_mux0 */
+			0x02c (PIN_INPUT_PULLUP | MUX_MODE2)      /* gpmc_ad11.mmc1_dat3_mux0 */
+			0x080 (PIN_INPUT_PULLUP | MUX_MODE2)      /* gpmc_csn1.mmc1_clk_mux0 */
+			0x084 (PIN_INPUT_PULLUP | MUX_MODE2)      /* gpmc_csn2.mmc1_cmd_mux0 */
+			0x1e4 (PIN_INPUT_PULLUP | MUX_MODE7)      /* emu0.gpio3[7] */
+		>;
+	};
+
+	wl12xx_gpio: pinmux_wl12xx_gpio {
+		pinctrl-single,pins = <
+			0x1e8 (PIN_OUTPUT_PULLUP | MUX_MODE7)      /* emu1.gpio3[8] */
+		>;
+	};
+
+	tps65910_pins: pinmux_tps65910_pins {
+		pinctrl-single,pins = <
+			0x078 (PIN_INPUT_PULLUP | MUX_MODE7)      /* gpmc_ben1.gpio1[28] */
+		>;
+	};
+
+	tca6416_pins: pinmux_tca6416_pins {
+		pinctrl-single,pins = <
+			0x1b4 (PIN_INPUT_PULLUP | MUX_MODE7)      /* xdma_event_intr1.gpio0[20] tca6416 stuff */
+		>;
+	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			0x158 0x2a      /* spi0_d1.i2c1_sda_mux3, INPUT | MODE2 */
+			0x15c 0x2a      /* spi0_cs0.i2c1_scl_mux3, INPUT | MODE2 */
+		>;
+	};
+
+	dcan1_pins: pinmux_dcan1_pins {
+		pinctrl-single,pins = <
+			0x168 0x0a      /* uart0_ctsn.dcan1_tx_mux0, OUTPUT | MODE2 */
+			0x16c 0x2a      /* uart0_rtsn.dcan1_rx_mux0, INPUT | MODE2 */
+		>;
+	};
+
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			0x170 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+			0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)		/* uart0_txd.uart0_txd */
+		>;
+	};
+
+	uart1_pins: pinmux_uart1_pins {
+		pinctrl-single,pins = <
+			0x180 0x28      /* uart1_rxd, INPUT | MODE0 */
+			0x184 0x28      /* uart1_txd, INPUT | MODE0 */
+			/*0x178 0x28*/      /* uart1_ctsn, INPUT | MODE0 */
+			/*0x17c 0x08*/      /* uart1_rtsn, OUTPUT | MODE0 */
+			0x178 (PIN_INPUT_PULLDOWN | MUX_MODE7)      /* uart1_ctsn, INPUT | MODE0 */
+			0x17c (PIN_OUTPUT_PULLDOWN | MUX_MODE7)      /* uart1_rtsn, OUTPUT | MODE0 */
+			0x0e0 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)      /* lcd_vsync.gpio2[22] DTR */
+			0x0e4 (PIN_INPUT_PULLDOWN | MUX_MODE7)      /* lcd_hsync.gpio2[23] DSR */
+			0x0e8 (PIN_INPUT_PULLDOWN | MUX_MODE7)      /* lcd_pclk.gpio2[24] DCD */
+			0x0ec (PIN_INPUT_PULLDOWN | MUX_MODE7)      /* lcd_ac_bias_en.gpio2[25] RI */
+		>;
+	};
+
+	uart2_pins: pinmux_uart2_pins {
+		pinctrl-single,pins = <
+			0x150 0x29      /* spi0_sclk.uart2_rxd_mux3, INPUT | MODE1 */
+			0x154 0x09      /* spi0_d0.uart2_txd_mux3, OUTPUT | MODE1 */
+			/*0x188 0x2a*/      /* i2c0_sda.uart2_ctsn_mux0, INPUT | MODE2 */
+			/*0x18c 0x2a*/      /* i2c0_scl.uart2_rtsn_mux0, INPUT | MODE2 */
+			0x188 (PIN_INPUT_PULLDOWN | MUX_MODE7)      /* i2c0_sda.uart2_ctsn_mux0 */
+			0x18c (PIN_OUTPUT_PULLDOWN | MUX_MODE7)      /* i2c0_scl.uart2_rtsn_mux0 */
+			0x030 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)      /* gpmc_ad12.gpio1[12] DTR */
+			0x034 (PIN_INPUT_PULLDOWN | MUX_MODE7)      /* gpmc_ad13.gpio1[13] DSR */
+			0x038 (PIN_INPUT_PULLDOWN | MUX_MODE7)      /* gpmc_ad14.gpio1[14] DCD */
+			0x03c (PIN_INPUT_PULLDOWN | MUX_MODE7)     /* gpmc_ad15.gpio1[15] RI */
+
+			0x1a0 (PIN_INPUT_PULLUP | MUX_MODE7)      /* mcasp0_aclkr.gpio3[18], INPUT_PULLDOWN | MODE7 */
+		>;
+	};
+
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1)       /* mii1_crs.rmii1_crs_dv */
+			0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)      /* mii1_tx_en.rmii1_txen */
+			0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)      /* mii1_txd1.rmii1_txd1 */
+			0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1)      /* mii1_txd0.rmii1_txd0 */
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1)      /* mii1_rxd1.rmii1_rxd1 */
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1)      /* mii1_rxd0.rmii1_rxd0 */
+			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0)      /* rmii1_ref_clk.rmii1_refclk */
+
+
+			/* Slave 2 */
+			0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a0.rgmii2_tctl */
+			0x44 (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a1.rgmii2_rctl */
+			0x48 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a2.rgmii2_td3 */
+			0x4c (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a3.rgmii2_td2 */
+			0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a4.rgmii2_td1 */
+			0x54 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a5.rgmii2_td0 */
+			0x58 (PIN_OUTPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a6.rgmii2_tclk */
+			0x5c (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a7.rgmii2_rclk */
+			0x60 (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a8.rgmii2_rd3 */
+			0x64 (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a9.rgmii2_rd2 */
+			0x68 (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a10.rgmii2_rd1 */
+			0x6c (PIN_INPUT_PULLDOWN | MUX_MODE2)	/* gpmc_a11.rgmii2_rd0 */
+		>;
+	};
+
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+
+			/* Slave 2 reset value*/
+			0x40 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x50 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x54 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x58 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x5c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x60 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x64 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x68 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x6c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	davinci_mdio_default: davinci_mdio_default {
+		pinctrl-single,pins = <
+			/* MDIO */
+			0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
+			0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0)			/* mdio_clk.mdio_clk */
+		>;
+	};
+
+	davinci_mdio_sleep: davinci_mdio_sleep {
+		pinctrl-single,pins = <
+			/* MDIO reset value */
+			0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+			0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	nandflash_pins_s0: nandflash_pins_s0 {
+		pinctrl-single,pins = <
+			0x0 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
+			0x4 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
+			0x8 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
+			0xc (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
+			0x10 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
+			0x14 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
+			0x18 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
+			0x1c (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
+			0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
+			0x74 (PIN_INPUT_PULLUP | MUX_MODE7)	/* gpmc_wpn.gpio0_30 */
+			0x7c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0  */
+			0x90 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
+			0x94 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
+			0x98 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
+			0x9c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_be0n_cle.gpmc_be0n_cle */
+		>;
+	};
+};
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&nandflash_pins_s0>;
+	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+	status = "okay";
+
+	nand@0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		nand-bus-width = <8>;
+		ti,nand-ecc-opt = "bch8";
+		ti,nand-xfer-type = "polled";
+
+		gpmc,device-nand = "true";
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		elm_id = <&elm>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	dtr-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>;
+	dsr-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+	dcd-gpios = <&gpio2 24 GPIO_ACTIVE_LOW>;
+	rng-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>;
+	cts-gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+	rts-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	dtr-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+	dsr-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+	dcd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+	rng-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+	cts-gpios = <&gpio3 5 GPIO_ACTIVE_LOW>;
+	rts-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tps: tps@2d {
+		reg = <0x2d>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <28 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tps65910_pins>;
+	};
+
+	at24@50 {
+		compatible = "at24,24c02";
+		pagesize = <8>;
+		reg = <0x50>;
+	};
+
+	tca6416: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <20 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tca6416_pins>;
+	};
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_ctrl_mod {
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "otg";
+};
+
+&cppi41dma  {
+	status = "okay";
+};
+
+#include "tps65910.dtsi"
+
+&tps {
+	vcc1-supply = <&vbat>;
+	vcc2-supply = <&vbat>;
+	vcc3-supply = <&vbat>;
+	vcc4-supply = <&vbat>;
+	vcc5-supply = <&vbat>;
+	vcc6-supply = <&vbat>;
+	vcc7-supply = <&vbat>;
+	vccio-supply = <&vbat>;
+
+	ti,en-ck32k-xtal = <1>;
+
+	regulators {
+		vrtc_reg: regulator@0 {
+			regulator-always-on;
+		};
+
+		vio_reg: regulator@1 {
+			regulator-always-on;
+		};
+
+		vdd1_reg: regulator@2 {
+			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <912500>;
+			regulator-max-microvolt = <1312500>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd2_reg: regulator@3 {
+			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <912500>;
+			regulator-max-microvolt = <1150000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd3_reg: regulator@4 {
+			regulator-always-on;
+		};
+
+		vdig1_reg: regulator@5 {
+			regulator-always-on;
+		};
+
+		vdig2_reg: regulator@6 {
+			regulator-always-on;
+		};
+
+		vpll_reg: regulator@7 {
+			regulator-always-on;
+		};
+
+		vdac_reg: regulator@8 {
+			regulator-always-on;
+		};
+
+		vaux1_reg: regulator@9 {
+			regulator-always-on;
+		};
+
+		vaux2_reg: regulator@10 {
+			regulator-always-on;
+		};
+
+		vaux33_reg: regulator@11 {
+			regulator-always-on;
+		};
+
+		vmmc_reg: regulator@12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+	};
+};
+
+&mac {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+	dual_emac = <1>;
+
+	status = "okay";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+
+	status = "okay";
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <0>;
+	phy-mode = "rmii";
+	dual_emac_res_vlan = <1>;
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <7>;
+	phy-mode = "rgmii-txid";
+	dual_emac_res_vlan = <2>;
+};
+
+&phy_sel {
+	rmii-clock-ext = <1>;
+};
+
+&mmc1 {
+	vmmc-supply = <&vmmc_reg>;
+	status = "okay";
+};
+
+&mmc2 {
+	status = "okay";
+	vmmc-supply = <&wl12xx_vmmc>;
+	ti,non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&sham {
+	status = "okay";
+};
+
+&aes {
+	status = "okay";
+};
+
+&gpio0 {
+	ti,no-reset-on-init;
+};
+
+&dcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dcan1_pins>;
+
+	status = "okay";
+};

arch/arm/boot/dts/am335x-bone-common.dtsi

@@ -81,6 +81,13 @@
 		>;
 	};
 
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			0x178 (PIN_INPUT_PULLUP | MUX_MODE3)	/* uart1_ctsn.i2c2_sda */
+			0x17c (PIN_INPUT_PULLUP | MUX_MODE3)	/* uart1_rtsn.i2c2_scl */
+		>;
+	};
+
 	uart0_pins: pinmux_uart0_pins {
 		pinctrl-single,pins = <
 			0x170 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
@@ -218,8 +225,67 @@
 		reg = <0x24>;
 	};
 
+	baseboard_eeprom: baseboard_eeprom@50 {
+		compatible = "at,24c256";
+		reg = <0x50>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		baseboard_data: baseboard_data@0 {
+			reg = <0 0x100>;
+		};
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+
+	status = "okay";
+	clock-frequency = <100000>;
+
+	cape_eeprom0: cape_eeprom0@54 {
+		compatible = "at,24c256";
+		reg = <0x54>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		cape0_data: cape_data@0 {
+			reg = <0 0x100>;
+		};
+	};
+
+	cape_eeprom1: cape_eeprom1@55 {
+		compatible = "at,24c256";
+		reg = <0x55>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		cape1_data: cape_data@0 {
+			reg = <0 0x100>;
+		};
+	};
+
+	cape_eeprom2: cape_eeprom2@56 {
+		compatible = "at,24c256";
+		reg = <0x56>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		cape2_data: cape_data@0 {
+			reg = <0 0x100>;
+		};
+	};
+
+	cape_eeprom3: cape_eeprom3@57 {
+		compatible = "at,24c256";
+		reg = <0x57>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		cape3_data: cape_data@0 {
+			reg = <0 0x100>;
+		};
+	};
 };
 
+
 /include/ "tps65217.dtsi"
 
 &tps {

arch/arm/boot/dts/am335x-evm.dts

@@ -8,6 +8,7 @@
 /dts-v1/;
 
 #include "am33xx.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "TI AM335x EVM";
@@ -38,6 +39,20 @@
 		regulator-boot-on;
 	};
 
+	wlan_en_reg: fixedregulator@2 {
+		compatible = "regulator-fixed";
+		regulator-name = "wlan-en-regulator";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		/* WLAN_EN GPIO for this board - Bank1, pin16 */
+		gpio = <&gpio1 16 0>;
+
+		/* WLAN card specific delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
 	matrix_keypad: matrix_keypad@0 {
 		compatible = "gpio-matrix-keypad";
 		debounce-delay-ms = <5>;
@@ -176,6 +191,15 @@
 		>;
 	};
 
+	uart1_pins: pinmux_uart1_pins {
+		pinctrl-single,pins = <
+			0x178 (PIN_INPUT | MUX_MODE0)		/* uart1_ctsn.uart1_ctsn */
+			0x17C (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_rtsn.uart1_rtsn */
+			0x180 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart1_rxd.uart1_rxd */
+			0x184 (PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart1_txd.uart1_txd */
+		>;
+	};
+
 	clkout2_pin: pinmux_clkout2_pin {
 		pinctrl-single,pins = <
 			0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3)	/* xdma_event_intr1.clkout2 */
@@ -266,6 +290,25 @@
 		>;
 	};
 
+	mmc3_pins: pinmux_mmc3_pins {
+		pinctrl-single,pins = <
+			0x44 (PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_a1.mmc2_dat0, INPUT_PULLUP | MODE3 */
+			0x48 (PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_a2.mmc2_dat1, INPUT_PULLUP | MODE3 */
+			0x4C (PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_a3.mmc2_dat2, INPUT_PULLUP | MODE3 */
+			0x78 (PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_ben1.mmc2_dat3, INPUT_PULLUP | MODE3 */
+			0x88 (PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_csn3.mmc2_cmd, INPUT_PULLUP | MODE3 */
+			0x8C (PIN_INPUT_PULLUP | MUX_MODE3)	/* gpmc_clk.mmc2_clk, INPUT_PULLUP | MODE3 */
+		>;
+	};
+
+	wlan_pins: pinmux_wlan_pins {
+		pinctrl-single,pins = <
+			0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a0.gpio1_16 */
+			0x19C (PIN_INPUT | MUX_MODE7)		/* mcasp0_ahclkr.gpio3_17 */
+			0x1AC (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* mcasp0_ahclkx.gpio3_21 */
+		>;
+	};
+
 	lcd_pins_s0: lcd_pins_s0 {
 		pinctrl-single,pins = <
 			0x20 (PIN_OUTPUT | MUX_MODE1)		/* gpmc_ad8.lcd_data23 */
@@ -323,6 +366,13 @@
 	status = "okay";
 };
 
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+
+	status = "okay";
+};
+
 &i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2c0_pins>;
@@ -665,6 +715,37 @@
 	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
 };
 
+&mmc3 {
+	/* these are on the crossbar and are outlined in the
+	   xbar-event-map element */
+	dmas = <&edma 12
+		&edma 13>;
+	dma-names = "tx", "rx";
+	status = "okay";
+	vmmc-supply = <&wlan_en_reg>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins &wlan_pins>;
+	ti,non-removable;
+	ti,needs-special-hs-handling;
+	cap-power-off-card;
+	keep-power-in-suspend;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@0 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&edma {
+	ti,edma-xbar-event-map = /bits/ 16 <1 12
+					    2 13>;
+};
+
 &sham {
 	status = "okay";
 };

arch/arm/boot/dts/am335x-sl50.dts

@@ -0,0 +1,482 @@
+/*
+ * Copyright (C) 2015 Toby Churchill - http://www.toby-churchill.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+/ {
+	model = "Toby Churchill SL50 Series";
+	compatible = "tcl,am335x-sl50", "ti,am33xx";
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&dcdc2_reg>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins>;
+
+		led@0 {
+			label = "sl50:green:usr0";
+			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led@1 {
+			label = "sl50:red:usr1";
+			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led@2 {
+			label = "sl50:green:usr2";
+			gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led@3 {
+			label = "sl50:red:usr3";
+			gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	backlight0: disp0 {
+		compatible = "pwm-backlight";
+		pwms = <&ehrpwm1 0 500000 0>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 99>;
+		default-brightness-level = <6>;
+	};
+
+	backlight1: disp1 {
+		compatible = "pwm-backlight";
+		pwms = <&ehrpwm1 1 500000 0>;
+		brightness-levels = <0 10 20 30 40 50 60 70 80 90 99>;
+		default-brightness-level = <6>;
+	};
+
+	sound {
+		compatible = "ti,da830-evm-audio";
+		ti,model = "AM335x-SL50";
+		ti,audio-codec = <&audio_codec>;
+		ti,mcasp-controller = <&mcasp0>;
+		ti,codec-clock-rate = <12000000>;
+		ti,audio-routing =
+			"Headphone Jack",	"HPLOUT",
+			"Headphone Jack",	"HPROUT",
+			"LINE1R",               "Line In",
+			"LINE1L",		"Line In";
+	};
+
+	emmc_pwrseq: pwrseq@0 {
+		compatible = "mmc-pwrseq-emmc";
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_pwrseq_pins>;
+		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+	};
+
+	vmmcsd_fixed: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&am33xx_pinmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lwb_pins>;
+
+	led_pins: pinmux_led_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x854, PIN_OUTPUT | MUX_MODE7)	/* gpmc_a5.gpio1_21 */
+			AM33XX_IOPAD(0x858, PIN_OUTPUT | MUX_MODE7)	/* gpmc_a6.gpio1_22 */
+			AM33XX_IOPAD(0x85c, PIN_OUTPUT | MUX_MODE7)	/* gpmc_a7.gpio1_23 */
+			AM33XX_IOPAD(0x860, PIN_OUTPUT | MUX_MODE7)	/* gpmc_a8.gpio1_24 */
+		>;
+	};
+
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart0_rxd.uart0_rxd */
+			AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* uart0_txd.uart0_txd */
+		>;
+	};
+
+	uart4_pins: pinmux_uart4_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x870, PIN_INPUT_PULLUP | MUX_MODE6)	/* gpmc_wait0.uart4_rxd */
+			AM33XX_IOPAD(0x874, PIN_OUTPUT_PULLDOWN | MUX_MODE6)	/* gpmc_wpn.uart4_txd */
+		>;
+	};
+
+	i2c0_pins: pinmux_i2c0_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_sda.i2c0_sda */
+			AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
+		>;
+	};
+
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x980, PIN_INPUT_PULLUP | MUX_MODE3)	/* uart1_rxd.i2c1_sda */
+			AM33XX_IOPAD(0x984, PIN_INPUT_PULLUP | MUX_MODE3)	/* uart1_txdi2c1_scl */
+		>;
+	};
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x978, PIN_INPUT_PULLUP | MUX_MODE3)	/* uart1_ctsn.i2c2_sda */
+			AM33XX_IOPAD(0x97c, PIN_INPUT_PULLUP | MUX_MODE3)	/* uart1_rtsn.i2c2_scl */
+		>;
+	};
+
+	cpsw_default: cpsw_default {
+		pinctrl-single,pins = <
+			/* Slave 1 */
+			AM33XX_IOPAD(0x910, PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxerr.mii1_rxerr */
+			AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txen.mii1_txen */
+			AM33XX_IOPAD(0x918, PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxdv.mii1_rxdv */
+			AM33XX_IOPAD(0x91c, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txd3.mii1_txd3 */
+			AM33XX_IOPAD(0x920, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txd2.mii1_txd2 */
+			AM33XX_IOPAD(0x924, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txd1.mii1_txd1 */
+			AM33XX_IOPAD(0x928, PIN_OUTPUT_PULLDOWN | MUX_MODE0)	/* mii1_txd0.mii1_txd0 */
+			AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_txclk.mii1_txclk */
+			AM33XX_IOPAD(0x930, PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxclk.mii1_rxclk */
+			AM33XX_IOPAD(0x934, PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxd3.mii1_rxd3 */
+			AM33XX_IOPAD(0x938, PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxd2.mii1_rxd2 */
+			AM33XX_IOPAD(0x93c, PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxd1.mii1_rxd1 */
+			AM33XX_IOPAD(0x940, PIN_INPUT_PULLUP | MUX_MODE0)	/* mii1_rxd0.mii1_rxd0 */
+		>;
+	};
+
+	cpsw_sleep: cpsw_sleep {
+		pinctrl-single,pins = <
+			/* Slave 1 reset value */
+			AM33XX_IOPAD(0x910, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x914, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x918, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x91c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x920, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x924, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x928, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x92c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x930, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x934, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x938, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x93c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x940, PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	davinci_mdio_default: davinci_mdio_default {
+		pinctrl-single,pins = <
+			/* MDIO */
+			AM33XX_IOPAD(0x948, PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* mdio_data.mdio_data */
+			AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE0)			/* mdio_clk.mdio_clk */
+		>;
+	};
+
+	davinci_mdio_sleep: davinci_mdio_sleep {
+		pinctrl-single,pins = <
+			/* MDIO reset value */
+			AM33XX_IOPAD(0x948, PIN_INPUT_PULLDOWN | MUX_MODE7)
+			AM33XX_IOPAD(0x94c, PIN_INPUT_PULLDOWN | MUX_MODE7)
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7)		/* spi0_cs1.gpio0_6 */
+		>;
+	};
+
+	emmc_pwrseq_pins: pinmux_emmc_pwrseq_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x850, PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_a4.gpio1_20 */
+		>;
+	};
+
+	emmc_pins: pinmux_emmc_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x880, PIN_INPUT_PULLUP | MUX_MODE2)	/* gpmc_csn1.mmc1_clk */
+			AM33XX_IOPAD(0x884, PIN_INPUT_PULLUP | MUX_MODE2)	/* gpmc_csn2.mmc1_cmd */
+			AM33XX_IOPAD(0x800, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_ad0.mmc1_dat0 */
+			AM33XX_IOPAD(0x804, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_ad1.mmc1_dat1 */
+			AM33XX_IOPAD(0x808, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_ad2.mmc1_dat2 */
+			AM33XX_IOPAD(0x80c, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_ad3.mmc1_dat3 */
+			AM33XX_IOPAD(0x810, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_ad4.mmc1_dat4 */
+			AM33XX_IOPAD(0x814, PIN_INPUT_PULLUP | MUX_MODE1) 	/* gpmc_ad5.mmc1_dat5 */
+			AM33XX_IOPAD(0x818, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_ad6.mmc1_dat6 */
+			AM33XX_IOPAD(0x81c, PIN_INPUT_PULLUP | MUX_MODE1)	/* gpmc_ad7.mmc1_dat7 */
+		>;
+	};
+
+	audio_pins: pinmux_audio_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9ac, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp0_ahcklx.mcasp0_ahclkx */
+			AM33XX_IOPAD(0x994, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp0_fsx.mcasp0_fsx */
+			AM33XX_IOPAD(0x990, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp0_aclkx.mcasp0_aclkx */
+			AM33XX_IOPAD(0x998, PIN_INPUT_PULLDOWN | MUX_MODE0)	/* mcasp0_axr0.mcasp0_axr0 */
+			AM33XX_IOPAD(0x99c, PIN_INPUT_PULLDOWN | MUX_MODE2)	/* mcasp0_ahclkr.mcasp0_axr2*/
+		>;
+	};
+
+	ehrpwm1_pins: pinmux_ehrpwm1a_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x848, PIN_OUTPUT | MUX_MODE6)	/* gpmc_a2.ehrpwm1a */
+			AM33XX_IOPAD(0x84c, PIN_OUTPUT | MUX_MODE6)	/* gpmc_a3.ehrpwm1b */
+		>;
+	};
+
+	lwb_pins: pinmux_lwb_pins {
+		pinctrl-single,pins = <
+			AM33XX_IOPAD(0x9a4, PIN_OUTPUT | MUX_MODE7)	/* SoundPA_en - mcasp0_fsr.gpio3_19 */
+			AM33XX_IOPAD(0x828, PIN_OUTPUT | MUX_MODE7)	/* nKbdOnC - gpmc_ad10.gpio0_26 */
+			AM33XX_IOPAD(0x830, PIN_INPUT_PULLUP | MUX_MODE7)	/* nKbdInt - gpmc_ad12.gpio1_12 */
+			AM33XX_IOPAD(0x834, PIN_INPUT_PULLUP | MUX_MODE7)	/* nKbdReset - gpmc_ad13.gpio1_13 */
+			AM33XX_IOPAD(0x838, PIN_INPUT_PULLUP | MUX_MODE7)	/* nDispReset - gpmc_ad14.gpio1_14 */
+			AM33XX_IOPAD(0x844, PIN_INPUT_PULLUP | MUX_MODE7)	/* USB1_enPower - gpmc_a1.gpio1_17 */
+			/* AVR Programming - SPI Bus (bit bang) - Screen and Keyboard */
+			AM33XX_IOPAD(0x954, PIN_INPUT_PULLUP | MUX_MODE7)	/* Kbd/Disp/BattMOSI spi0_d0.gpio0_3 */
+			AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE7)	/* Kbd/Disp/BattMISO spi0_d1.gpio0_4 */
+			AM33XX_IOPAD(0x950, PIN_INPUT_PULLUP | MUX_MODE7)	/* Kbd/Disp/BattSCLK spi0_clk.gpio0_2 */
+			/* PDI Bus - Battery system */
+			AM33XX_IOPAD(0x840, PIN_INPUT_PULLUP | MUX_MODE7)	/* nBattReset  gpmc_a0.gpio1_16 */
+			AM33XX_IOPAD(0x83c, PIN_INPUT_PULLUP | MUX_MODE7)	/* BattPDIData gpmc_ad15.gpio1_15 */
+		>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	clock-frequency = <400000>;
+
+	tps: tps@24 {
+		reg = <0x24>;
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "at,24c256";
+		reg = <0x50>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+};
+
+&i2c2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+
+	clock-frequency = <400000>;
+
+	audio_codec: tlv320aic3106@1b {
+		status = "okay";
+		compatible = "ti,tlv320aic3106";
+		reg = <0x1b>;
+
+		AVDD-supply = <&ldo4_reg>;
+		IOVDD-supply = <&ldo4_reg>;
+		DRVDD-supply = <&ldo4_reg>;
+		DVDD-supply = <&ldo3_reg>;
+	};
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_ctrl_mod {
+	status = "okay";
+};
+
+&usb0_phy {
+	status = "okay";
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "peripheral";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&cppi41dma  {
+	status = "okay";
+};
+
+&mmc1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	bus-width = <4>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&vmmcsd_fixed>;
+};
+
+&mmc2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_pins>;
+	bus-width = <8>;
+	vmmc-supply = <&vmmcsd_fixed>;
+	mmc-pwrseq = <&emmc_pwrseq>;
+};
+
+&mcasp0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&audio_pins>;
+
+	op-mode = <0>;  /* MCASP_ISS_MODE */
+	tdm-slots = <2>;
+	serial-dir = <
+		2 0 1 0
+		0 0 0 0
+		0 0 0 0
+		0 0 0 0
+	>;
+	tx-num-evt = <1>;
+	rx-num-evt = <1>;
+};
+
+&uart0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+};
+
+&uart4 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins>;
+};
+
+#include "tps65217.dtsi"
+
+&tps {
+	ti,pmic-shutdown-controller;
+
+	interrupt-parent = <&intc>;
+	interrupts = <7>;	/* NNMI */
+
+	regulators {
+		dcdc1_reg: regulator@0 {
+			/* VDDS_DDR */
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			regulator-always-on;
+		};
+
+		dcdc2_reg: regulator@1 {
+			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+			regulator-name = "vdd_mpu";
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <1325000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		dcdc3_reg: regulator@2 {
+			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <1150000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		ldo1_reg: regulator@3 {
+			/* VRTC / VIO / VDDS*/
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		ldo2_reg: regulator@4 {
+			/* VDD_3V3AUX */
+			regulator-always-on;
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		ldo3_reg: regulator@5 {
+			/* VDD_1V8 */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		ldo4_reg: regulator@6 {
+			/* VDD_3V3A */
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+	};
+};
+
+&cpsw_emac0 {
+	phy_id = <&davinci_mdio>, <0>;
+	phy-mode = "mii";
+};
+
+&cpsw_emac1 {
+	phy_id = <&davinci_mdio>, <1>;
+	phy-mode = "mii";
+};
+
+&mac {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cpsw_default>;
+	pinctrl-1 = <&cpsw_sleep>;
+};
+
+&davinci_mdio {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+};
+
+&sham {
+	status = "okay";
+};
+
+&aes {
+	status = "okay";
+};
+
+&epwmss1 {
+	status = "okay";
+};
+
+&ehrpwm1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ehrpwm1_pins>;
+};

arch/arm/boot/dts/am3517.dtsi

@@ -60,6 +60,17 @@
 			dma-names = "tx", "rx";
 			clock-frequency = <48000000>;
 		};
+
+		omap3_pmx_core2: pinmux@480025d8 {
+			compatible = "ti,omap3-padconf", "pinctrl-single";
+			reg = <0x480025d8 0x24>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			pinctrl-single,register-width = <16>;
+			pinctrl-single,function-mask = <0xff1f>;
+		};
 	};
 };
 

arch/arm/boot/dts/am437x-gp-evm.dts

@@ -21,6 +21,7 @@
 
 	aliases {
 		display0 = &lcd0;
+		serial3 = &uart3;
 	};
 
 	vmmcsd_fixed: fixedregulator-sd {
@@ -42,6 +43,15 @@
 		gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>;
 	};
 
+	vmmcwl_fixed: fixedregulator-mmcwl {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcwl_fixed";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	backlight {
 		compatible = "pwm-backlight";
 		pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>;
@@ -106,9 +116,21 @@
 			};
 		};
 	};
+
+	/* fixed 12MHz oscillator */
+	refclk: oscillator {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <12000000>;
+	};
+
 };
 
 &am43xx_pinmux {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&wlan_pins_default>;
+	pinctrl-1 = <&wlan_pins_sleep>;
+
 	i2c0_pins: i2c0_pins {
 		pinctrl-single,pins = <
 			0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_sda.i2c0_sda */
@@ -340,6 +362,53 @@
 			0x204 (DS0_PULL_UP_DOWN_EN | INPUT_EN | MUX_MODE7)  /* cam1_data7 mode 0*/
 		>;
 	};
+
+	mmc3_pins_default: pinmux_mmc3_pins_default {
+		pinctrl-single,pins = <
+			0x8c (PIN_INPUT_PULLUP | MUX_MODE3)      /* gpmc_clk.mmc2_clk */
+			0x88 (PIN_INPUT_PULLUP | MUX_MODE3)      /* gpmc_csn3.mmc2_cmd */
+			0x44 (PIN_INPUT_PULLUP | MUX_MODE3)      /* gpmc_a1.mmc2_dat0 */
+			0x48 (PIN_INPUT_PULLUP | MUX_MODE3)      /* gpmc_a2.mmc2_dat1 */
+			0x4c (PIN_INPUT_PULLUP | MUX_MODE3)      /* gpmc_a3.mmc2_dat2 */
+			0x78 (PIN_INPUT_PULLUP | MUX_MODE3)      /* gpmc_be1n.mmc2_dat3 */
+		>;
+	};
+
+	mmc3_pins_sleep: pinmux_mmc3_pins_sleep {
+		pinctrl-single,pins = <
+			0x8c (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_clk.mmc2_clk */
+			0x88 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_csn3.mmc2_cmd */
+			0x44 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a1.mmc2_dat0 */
+			0x48 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a2.mmc2_dat1 */
+			0x4c (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a3.mmc2_dat2 */
+			0x78 (PIN_INPUT_PULLDOWN | MUX_MODE7)	/* gpmc_be1n.mmc2_dat3 */
+		>;
+	};
+
+	wlan_pins_default: pinmux_wlan_pins_default {
+		pinctrl-single,pins = <
+			0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)		/* gpmc_a4.gpio1_20 WL_EN */
+			0x5c (PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7)	/* gpmc_a7.gpio1_23 WL_IRQ*/
+			0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)		/* gpmc_a0.gpio1_16 BT_EN*/
+		>;
+	};
+
+	wlan_pins_sleep: pinmux_wlan_pins_sleep {
+		pinctrl-single,pins = <
+			0x50 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)		/* gpmc_a4.gpio1_20 WL_EN */
+			0x5c (PIN_INPUT | WAKEUP_ENABLE | MUX_MODE7)	/* gpmc_a7.gpio1_23 WL_IRQ*/
+			0x40 (PIN_OUTPUT_PULLUP | MUX_MODE7)		/* gpmc_a0.gpio1_16 BT_EN*/
+		>;
+	};
+
+	uart3_pins: uart3_pins {
+		pinctrl-single,pins = <
+			0x228 (PIN_INPUT | MUX_MODE0)		/* uart3_rxd.uart3_rxd */
+			0x22c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart3_txd.uart3_txd */
+			0x230 (PIN_INPUT_PULLUP | MUX_MODE0)	/* uart3_ctsn.uart3_ctsn */
+			0x234 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart3_rtsn.uart3_rtsn */
+		>;
+	};
 };
 
 &i2c0 {
@@ -403,6 +472,21 @@
 			regulator-always-on;
 		};
 	};
+
+	ov2659@30 {
+		compatible = "ovti,ov2659";
+		reg = <0x30>;
+
+		clocks = <&refclk 0>;
+		clock-names = "xvclk";
+
+		port {
+			ov2659_0: endpoint {
+				remote-endpoint = <&vpfe1_ep>;
+				link-frequencies = /bits/ 64 <70000000>;
+			};
+		};
+	};
 };
 
 &i2c1 {
@@ -422,6 +506,21 @@
 		touchscreen-size-x = <1024>;
 		touchscreen-size-y = <600>;
 	};
+
+	ov2659@30 {
+		compatible = "ovti,ov2659";
+		reg = <0x30>;
+
+		clocks = <&refclk 0>;
+		clock-names = "xvclk";
+
+		port {
+			ov2659_1: endpoint {
+				remote-endpoint = <&vpfe0_ep>;
+				link-frequencies = /bits/ 64 <70000000>;
+			};
+		};
+	};
 };
 
 &epwmss0 {
@@ -446,6 +545,10 @@
 	status = "okay";
 };
 
+&gpio1 {
+	status = "okay";
+};
+
 &gpio3 {
 	status = "okay";
 };
@@ -468,6 +571,43 @@
 	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
 };
 
+&mmc3 {
+	status = "okay";
+	/* these are on the crossbar and are outlined in the
+	   xbar-event-map element */
+	dmas = <&edma 30
+		&edma 31>;
+	dma-names = "tx", "rx";
+	vmmc-supply = <&vmmcwl_fixed>;
+	bus-width = <4>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&mmc3_pins_default>;
+	pinctrl-1 = <&mmc3_pins_sleep>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	ti,non-removable;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@0 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
+
+&edma {
+	ti,edma-xbar-event-map = /bits/ 16 <1 30
+					    2 31>;
+};
+
+&uart3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
+
 &usb2_phy1 {
 	status = "okay";
 };
@@ -625,7 +765,7 @@
 
 	port {
 		vpfe0_ep: endpoint {
-			/* remote-endpoint = <&sensor>; add once we have it */
+			remote-endpoint = <&ov2659_1>;
 			ti,am437x-vpfe-interface = <0>;
 			bus-width = <8>;
 			hsync-active = <0>;
@@ -642,7 +782,7 @@
 
 	port {
 		vpfe1_ep: endpoint {
-			/* remote-endpoint = <&sensor>; add once we have it */
+			remote-endpoint = <&ov2659_0>;
 			ti,am437x-vpfe-interface = <0>;
 			bus-width = <8>;
 			hsync-active = <0>;

arch/arm/boot/dts/armada-370-db.dts

@@ -162,7 +162,7 @@
 				spi-flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
-					compatible = "mx25l25635e";
+					compatible = "mx25l25635e", "jedec,spi-nor";
 					reg = <0>; /* Chip select 0 */
 					spi-max-frequency = <50000000>;
 				};

arch/arm/boot/dts/armada-370-dlink-dns327l.dts

@@ -0,0 +1,357 @@
+/*
+ * Device Tree file for D-Link DNS-327L
+ *
+ * Copyright (C) 2015, Andrew Andrianov <andrew@ncrmnt.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/* Remaining unsolved:
+ * There's still some unknown device on i2c address 0x13
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-370.dtsi"
+
+/ {
+	model = "D-Link DNS-327L";
+	compatible = "dlink,dns327l",
+		"marvell,armada370",
+		"marvell,armada-370-xp";
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>; /* 512 MiB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
+			MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000>;
+
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+
+			pcie@2,0 {
+				/* Port 1, Lane 0 */
+				status = "okay";
+			};
+		};
+
+		internal-regs {
+			sata@a0000 {
+				nr-ports = <2>;
+				status = "okay";
+			};
+
+			usb@50000 {
+				status = "okay";
+			};
+
+			nand@d0000 {
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+				nand-ecc-strength = <4>;
+				nand-ecc-step-size = <512>;
+
+				partition@0 {
+					label = "u-boot";
+					/* 1.0 MiB */
+					reg = <0x0000000 0x100000>;
+					read-only;
+				};
+
+				partition@100000 {
+					label = "u-boot-env";
+					/* 128 KiB */
+					reg = <0x100000 0x20000>;
+					read-only;
+				};
+
+				partition@120000 {
+					label = "uImage";
+					/* 7 MiB */
+					reg = <0x120000 0x700000>;
+				};
+
+				partition@820000 {
+					label = "ubifs";
+					/* ~ 84 MiB */
+					reg = <0x820000 0x54e0000>;
+				};
+
+				/* Hardcoded into stock bootloader */
+				partition@5d00000 {
+					label = "failsafe-uImage";
+					/* 5 MiB */
+					reg = <0x5d00000 0x500000>;
+				};
+
+				partition@6200000 {
+					label = "failsafe-fs";
+					/* 29 MiB */
+					reg = <0x6200000 0x1d00000>;
+				};
+
+				partition@7f00000 {
+					label = "bbt";
+					/* 1 MiB for BBT */
+					reg = <0x7f00000 0x100000>;
+				};
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <
+			&backup_button_pin
+			&power_button_pin
+			&reset_button_pin>;
+		pinctrl-names = "default";
+
+		power-button {
+			label = "Power Button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
+		};
+
+		backup-button {
+			label = "Backup Button";
+			linux,code = <KEY_COPY>;
+			gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
+		};
+
+		reset-button {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <
+			&sata_l_amber_pin
+			&sata_r_amber_pin
+			&backup_led_pin
+			/* Ensure these are managed by hardware */
+			&sata_l_white_pin
+			&sata_r_white_pin>;
+
+		pinctrl-names = "default";
+
+		sata-r-amber-pin {
+			label = "dns327l:amber:sata-r";
+			gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		sata-l-amber-pin {
+			label = "dns327l:amber:sata-l";
+			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+
+		backup-led-pin {
+			label = "dns327l:white:usb";
+			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
+			default-state = "keep";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usb_power: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			pinctrl-0 = <&xhci_pwr_pin>;
+			pinctrl-names = "default";
+			regulator-name = "USB3.0 Port Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-boot-on;
+			regulator-always-on;
+			gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+		};
+
+		sata_r_power: regulator@2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			pinctrl-0 = <&sata_r_pwr_pin>;
+			pinctrl-names = "default";
+			regulator-name = "SATA-R Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <2000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+		};
+
+		sata_l_power: regulator@3 {
+			compatible = "regulator-fixed";
+			reg = <3>;
+			pinctrl-0 = <&sata_l_pwr_pin>;
+			pinctrl-names = "default";
+			regulator-name = "SATA-L Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			startup-delay-us = <4000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&pinctrl {
+	sata_l_white_pin: sata-l-white-pin {
+		marvell,pins = "mpp57";
+		marvell,function = "sata0";
+	};
+
+	sata_r_white_pin: sata-r-white-pin {
+		marvell,pins = "mpp55";
+		marvell,function = "sata1";
+	};
+
+	sata_r_amber_pin: sata-r-amber-pin {
+		marvell,pins = "mpp52";
+		marvell,function = "gpio";
+	};
+
+	sata_l_amber_pin: sata-l-amber-pin {
+		marvell,pins = "mpp53";
+		marvell,function = "gpio";
+	};
+
+	backup_led_pin: backup-led-pin {
+		marvell,pins = "mpp61";
+		marvell,function = "gpo";
+	};
+
+	xhci_pwr_pin: xhci-pwr-pin {
+		marvell,pins = "mpp13";
+		marvell,function = "gpio";
+	};
+
+	sata_r_pwr_pin: sata-r-pwr-pin {
+		marvell,pins = "mpp54";
+		marvell,function = "gpio";
+	};
+
+	sata_l_pwr_pin: sata-l-pwr-pin {
+		marvell,pins = "mpp56";
+		marvell,function = "gpio";
+	};
+
+	uart1_pins: uart1-pins {
+		marvell,pins = "mpp60", "mpp61";
+		marvell,function = "uart1";
+	};
+
+	power_button_pin: power-button-pin {
+		marvell,pins = "mpp65";
+		marvell,function = "gpio";
+	};
+
+	backup_button_pin: backup-button-pin {
+		marvell,pins = "mpp63";
+		marvell,function = "gpio";
+	};
+
+	reset_button_pin: reset-button-pin {
+		marvell,pins = "mpp64";
+		marvell,function = "gpio";
+	};
+};
+
+/* Serial console */
+&uart0 {
+	status = "okay";
+};
+
+/* Connected to Weltrend MCU */
+&uart1 {
+	pinctrl-0 = <&uart1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&mdio {
+	phy0: ethernet-phy@0 { /* Marvell 88E1318 */
+		reg = <0>;
+		marvell,reg-init = <0x0 0x16 0x0 0x0002>,
+				<0x0 0x19 0x0 0x0077>,
+				<0x0 0x18 0x0 0x5747>;
+	};
+};
+
+&eth1 {
+	phy = <&phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&i2c0 {
+	compatible = "marvell,mv64xxx-i2c";
+	clock-frequency = <100000>;
+	status = "okay";
+};

arch/arm/boot/dts/armada-370-synology-ds213j.dts

@@ -92,7 +92,7 @@
 				spi-flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
-					compatible = "micron,n25q064";
+					compatible = "micron,n25q064", "jedec,spi-nor";
 					reg = <0>; /* Chip select 0 */
 					spi-max-frequency = <20000000>;
 

arch/arm/boot/dts/armada-370-xp.dtsi

@@ -149,7 +149,6 @@
 			};
 
 			spi0: spi@10600 {
-				compatible = "marvell,armada-370-spi", "marvell,orion-spi";
 				reg = <0x10600 0x28>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -160,7 +159,6 @@
 			};
 
 			spi1: spi@10680 {
-				compatible = "marvell,armada-370-spi", "marvell,orion-spi";
 				reg = <0x10680 0x28>;
 				#address-cells = <1>;
 				#size-cells = <0>;

arch/arm/boot/dts/armada-370.dtsi

@@ -139,11 +139,15 @@
 			 * board level if a different configuration is used.
 			 */
 			spi0: spi@10600 {
+				compatible = "marvell,armada-370-spi",
+						"marvell,orion-spi";
 				pinctrl-0 = <&spi0_pins1>;
 				pinctrl-names = "default";
 			};
 
 			spi1: spi@10680 {
+				compatible = "marvell,armada-370-spi",
+						"marvell,orion-spi";
 				pinctrl-0 = <&spi1_pins>;
 				pinctrl-names = "default";
 			};

arch/arm/boot/dts/armada-375-db.dts

@@ -81,7 +81,7 @@
 				spi-flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
-					compatible = "n25q128a13";
+					compatible = "n25q128a13", "jedec,spi-nor";
 					reg = <0>; /* Chip select 0 */
 					spi-max-frequency = <108000000>;
 				};

arch/arm/boot/dts/armada-375.dtsi

@@ -238,7 +238,8 @@
 			};
 
 			spi0: spi@10600 {
-				compatible = "marvell,orion-spi";
+				compatible = "marvell,armada-375-spi",
+						"marvell,orion-spi";
 				reg = <0x10600 0x50>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -249,7 +250,8 @@
 			};
 
 			spi1: spi@10680 {
-				compatible = "marvell,orion-spi";
+				compatible = "marvell,armada-375-spi",
+						"marvell,orion-spi";
 				reg = <0x10680 0x50>;
 				#address-cells = <1>;
 				#size-cells = <0>;

arch/arm/boot/dts/armada-385-db-ap.dts

@@ -70,7 +70,7 @@
 				spi-flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
-					compatible = "st,m25p128";
+					compatible = "st,m25p128", "jedec,spi-nor";
 					reg = <0>; /* Chip select 0 */
 					spi-max-frequency = <54000000>;
 				};

arch/arm/boot/dts/armada-385-linksys-caiman.dts

@@ -0,0 +1,114 @@
+/*
+ * Device Tree include for the Linksys WRT1200AC (Caiman)
+ *
+ * Copyright (C) 2015 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-385-linksys.dtsi"
+
+/ {
+	model = "Linksys WRT1200AC";
+	compatible = "linksys,caiman", "linksys,armada385", "marvell,armada385",
+		     "marvell,armada380";
+
+	soc {
+		internal-regs{
+			i2c@11000 {
+
+				pca9635@68 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+					wan_amber@0 {
+						label = "caiman:amber:wan";
+						reg = <0x0>;
+					};
+
+					wan_white@1 {
+						label = "caiman:white:wan";
+						reg = <0x1>;
+					};
+
+					wlan_2g@2 {
+						label = "caiman:white:wlan_2g";
+						reg = <0x2>;
+					};
+
+					wlan_5g@3 {
+						label = "caiman:white:wlan_5g";
+						reg = <0x3>;
+					};
+
+					usb2@5 {
+						label = "caiman:white:usb2";
+						reg = <0x5>;
+					};
+
+					usb3_1@6 {
+						label = "caiman:white:usb3_1";
+						reg = <0x6>;
+					};
+
+					usb3_2@7 {
+						label = "caiman:white:usb3_2";
+						reg = <0x7>;
+					};
+
+					wps_white@8 {
+						label = "caiman:white:wps";
+						reg = <0x8>;
+					};
+
+					wps_amber@9 {
+						label = "caiman:amber:wps";
+						reg = <0x9>;
+					};
+				};
+			};
+		};
+	};
+
+	gpio-leds {
+		power {
+			label = "caiman:white:power";
+		};
+
+		sata {
+			label = "caiman:white:sata";
+		};
+	};
+};

arch/arm/boot/dts/armada-385-linksys-cobra.dts

@@ -0,0 +1,114 @@
+/*
+ * Device Tree file for the Linksys WRT1900ACv2 (Cobra)
+ *
+ * Copyright (C) 2015 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-385-linksys.dtsi"
+
+/ {
+	model = "Linksys WRT1900ACv2";
+	compatible = "linksys,cobra", "linksys,armada385", "marvell,armada385",
+		     "marvell,armada380";
+
+	soc {
+		internal-regs{
+			i2c@11000 {
+
+				pca9635@68 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+					wan_amber@0 {
+						label = "cobra:amber:wan";
+						reg = <0x0>;
+					};
+
+					wan_white@1 {
+						label = "cobra:white:wan";
+						reg = <0x1>;
+					};
+
+					wlan_2g@2 {
+						label = "cobra:white:wlan_2g";
+						reg = <0x2>;
+					};
+
+					wlan_5g@3 {
+						label = "cobra:white:wlan_5g";
+						reg = <0x3>;
+					};
+
+					usb2@5 {
+						label = "cobra:white:usb2";
+						reg = <0x5>;
+					};
+
+					usb3_1@6 {
+						label = "cobra:white:usb3_1";
+						reg = <0x6>;
+					};
+
+					usb3_2@7 {
+						label = "cobra:white:usb3_2";
+						reg = <0x7>;
+					};
+
+					wps_white@8 {
+						label = "cobra:white:wps";
+						reg = <0x8>;
+					};
+
+					wps_amber@9 {
+						label = "cobra:amber:wps";
+						reg = <0x9>;
+					};
+				};
+			};
+		};
+	};
+
+	gpio-leds {
+		power {
+			label = "cobra:white:power";
+		};
+
+		sata {
+			label = "cobra:white:sata";
+		};
+	};
+};

arch/arm/boot/dts/armada-385-linksys.dtsi

@@ -0,0 +1,332 @@
+/*
+ * Device Tree include file for Armada 385 based Linksys boards
+ *
+ * Copyright (C) 2015 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is licensed under the terms of the GNU General Public
+ *     License version 2.  This program is licensed "as is" without
+ *     any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "armada-385.dtsi"
+
+/ {
+	model = "Linksys boards based on Armada 385";
+	compatible = "linksys,armada385", "marvell,armada385",
+		     "marvell,armada380";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>; /* 512 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+
+			spi@10600 {
+				status = "disabled";
+			};
+
+			i2c@11000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2c0_pins>;
+				status = "okay";
+
+				tmp421@4c {
+					compatible = "ti,tmp421";
+					reg = <0x4c>;
+				};
+
+				pca9635@68 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "nxp,pca9635";
+					reg = <0x68>;
+				};
+			};
+
+			/* J10: VCC, NC, RX, NC, TX, GND  */
+			serial@12000 {
+				status = "okay";
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				phy-mode = "rgmii-id";
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			ethernet@34000 {
+				status = "okay";
+				phy-mode = "sgmii";
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			mdio {
+				status = "okay";
+			};
+
+			sata@a8000 {
+				status = "okay";
+			};
+
+			/* USB part of the eSATA/USB 2.0 port */
+			usb@50000 {
+				status = "okay";
+			};
+
+			usb3@f8000 {
+				status = "okay";
+				usb-phy = <&usb3_phy>;
+			};
+
+			flash@d0000 {
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+
+				partition@0 {
+					label = "u-boot";
+					reg = <0x0000000 0x200000>;  /* 2MB */
+					read-only;
+				};
+
+				partition@100000 {
+					label = "u_env";
+					reg = <0x200000 0x40000>;    /* 256KB */
+				};
+
+				partition@140000 {
+					label = "s_env";
+					reg = <0x240000 0x40000>;    /* 256KB */
+				};
+
+				partition@900000 {
+					label = "devinfo";
+					reg = <0x900000 0x100000>;   /* 1MB */
+					read-only;
+				};
+
+				/* kernel1 overlaps with rootfs1 by design */
+				partition@a00000 {
+					label = "kernel1";
+					reg = <0xa00000 0x2800000>;  /* 40MB */
+				};
+
+				partition@1000000 {
+					label = "rootfs1";
+					reg = <0x1000000 0x2200000>;  /* 34MB */
+				};
+
+				/* kernel2 overlaps with rootfs2 by design */
+				partition@3200000 {
+					label = "kernel2";
+					reg = <0x3200000 0x2800000>; /* 40MB */
+				};
+
+				partition@3800000 {
+					label = "rootfs2";
+					reg = <0x3800000 0x2200000>; /* 34MB */
+				};
+
+				/*
+				 * 38MB, last MB is for the BBT, not writable
+				 */
+				partition@5a00000 {
+					label = "syscfg";
+					reg = <0x5a00000 0x2600000>;
+				};
+
+				/*
+				 * Unused area between "s_env" and "devinfo".
+				 * Moved here because otherwise the renumbered
+				 * partitions would break the bootloader
+				 * supplied bootargs
+				 */
+				partition@180000 {
+					label = "unused_area";
+					reg = <0x280000 0x680000>;   /* 6.5MB */
+				};
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+
+			pcie@1,0 {
+				/* Marvell 88W8864, 5GHz-only */
+				status = "okay";
+			};
+
+			pcie@2,0 {
+				/* Marvell 88W8864, 2GHz-only */
+				status = "okay";
+			};
+		};
+	};
+
+	usb3_phy: usb3_phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&reg_xhci0_vbus>;
+	};
+
+	reg_xhci0_vbus: xhci0-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&xhci0_vbus_pins>;
+		regulator-name = "xhci0-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&keys_pin>;
+		pinctrl-names = "default";
+
+		button@1 {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
+		};
+
+		button@2 {
+			label = "Factory Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&power_led_pin &sata_led_pin>;
+		pinctrl-names = "default";
+
+		power {
+			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+
+		sata {
+			gpios = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	dsa@0 {
+		compatible = "marvell,dsa";
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		dsa,ethernet = <&eth2>;
+		dsa,mii-bus = <&mdio>;
+
+		switch@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0>;	/* MDIO address 0, switch 0 in tree */
+
+			port@0 {
+				reg = <0>;
+				label = "lan4";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan3";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan2";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan1";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "wan";
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+			};
+		};
+	};
+};
+
+&pinctrl {
+	keys_pin: keys-pin {
+		marvell,pins = "mpp24", "mpp47";
+		marvell,function = "gpio";
+	};
+
+	power_led_pin: power-led-pin {
+		marvell,pins = "mpp55";
+		marvell,function = "gpio";
+	};
+
+	sata_led_pin: sata-led-pin {
+		marvell,pins = "mpp54";
+		marvell,function = "gpio";
+	};
+
+	xhci0_vbus_pins: xhci0-vbus-pins {
+		marvell,pins = "mpp50";
+		marvell,function = "gpio";
+	};
+};

arch/arm/boot/dts/armada-388-db.dts

@@ -73,7 +73,7 @@
 				spi-flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
-					compatible = "w25q32";
+					compatible = "w25q32", "jedec,spi-nor";
 					reg = <0>; /* Chip select 0 */
 					spi-max-frequency = <108000000>;
 				};

arch/arm/boot/dts/armada-388-gp.dts

@@ -69,7 +69,7 @@
 				spi-flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
-					compatible = "st,m25p128";
+					compatible = "st,m25p128", "jedec,spi-nor";
 					reg = <0>; /* Chip select 0 */
 					spi-max-frequency = <50000000>;
 					m25p,fast-read;

arch/arm/boot/dts/armada-388-rd.dts

@@ -74,7 +74,7 @@
 				spi-flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
-					compatible = "st,m25p128";
+					compatible = "st,m25p128", "jedec,spi-nor";
 					reg = <0>; /* Chip select 0 */
 					spi-max-frequency = <108000000>;
 				};

arch/arm/boot/dts/armada-38x.dtsi

@@ -167,7 +167,8 @@
 			};
 
 			spi0: spi@10600 {
-				compatible = "marvell,orion-spi";
+				compatible = "marvell,armada-380-spi",
+						"marvell,orion-spi";
 				reg = <0x10600 0x50>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -178,7 +179,8 @@
 			};
 
 			spi1: spi@10680 {
-				compatible = "marvell,orion-spi";
+				compatible = "marvell,armada-380-spi",
+						"marvell,orion-spi";
 				reg = <0x10680 0x50>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -495,7 +497,7 @@
 				status = "disabled";
 			};
 
-			mdio@72004 {
+			mdio: mdio@72004 {
 				#address-cells = <1>;
 				#size-cells = <0>;
 				compatible = "marvell,orion-mdio";

arch/arm/boot/dts/armada-398-db.dts

@@ -73,7 +73,7 @@
 				spi-flash@0 {
 					#address-cells = <1>;
 					#size-cells = <0>;
-					compatible = "n25q128a13";
+					compatible = "n25q128a13", "jedec,spi-nor";
 					reg = <0>;
 					spi-max-frequency = <108000000>;
 

arch/arm/boot/dts/armada-39x.dtsi

@@ -128,7 +128,8 @@
 			};
 
 			spi0: spi@10600 {
-				compatible = "marvell,orion-spi";
+				compatible = "marvell,armada-390-spi",
+						"marvell,orion-spi";
 				reg = <0x10600 0x50>;
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -139,7 +140,8 @@
 			};
 
 			spi1: spi@10680 {
-				compatible = "marvell,orion-spi";
+				compatible = "marvell,armada-390-spi",
+						"marvell,orion-spi";
 				reg = <0x10680 0x50>;
 				#address-cells = <1>;
 				#size-cells = <0>;

arch/arm/boot/dts/armada-xp-axpwifiap.dts

@@ -140,7 +140,7 @@
 				spi-flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
-					compatible = "n25q128a13";
+					compatible = "n25q128a13", "jedec,spi-nor";
 					reg = <0>; /* Chip select 0 */
 					spi-max-frequency = <108000000>;
 				};

arch/arm/boot/dts/armada-xp-db.dts

@@ -222,7 +222,7 @@
 				spi-flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
-					compatible = "m25p64";
+					compatible = "m25p64", "jedec,spi-nor";
 					reg = <0>; /* Chip select 0 */
 					spi-max-frequency = <20000000>;
 				};

arch/arm/boot/dts/armada-xp-gp.dts

@@ -227,7 +227,7 @@
 				spi-flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
-					compatible = "n25q128a13";
+					compatible = "n25q128a13", "jedec,spi-nor";
 					reg = <0>; /* Chip select 0 */
 					spi-max-frequency = <108000000>;
 				};

arch/arm/boot/dts/armada-xp-synology-ds414.dts

@@ -114,7 +114,7 @@
 				spi-flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
-					compatible = "micron,n25q064";
+					compatible = "micron,n25q064", "jedec,spi-nor";
 					reg = <0>; /* Chip select 0 */
 					spi-max-frequency = <20000000>;
 

arch/arm/boot/dts/armada-xp.dtsi

@@ -85,10 +85,18 @@
 			};
 
 			spi0: spi@10600 {
+				compatible = "marvell,armada-xp-spi",
+						"marvell,orion-spi";
 				pinctrl-0 = <&spi0_pins>;
 				pinctrl-names = "default";
 			};
 
+			spi1: spi@10680 {
+				compatible = "marvell,armada-xp-spi",
+						"marvell,orion-spi";
+			};
+
+
 			i2c0: i2c@11000 {
 				compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
 				reg = <0x11000 0x100>;

arch/arm/boot/dts/armv7-m.dtsi

@@ -8,6 +8,12 @@
 		reg = <0xe000e100 0xc00>;
 	};
 
+	systick: timer@e000e010 {
+		compatible = "arm,armv7m-systick";
+		reg = <0xe000e010 0x10>;
+		status = "disabled";
+	};
+
 	soc {
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm/boot/dts/at91-ariettag25.dts

@@ -0,0 +1,79 @@
+/*
+ * Device Tree file for Arietta G25
+ * This device tree is minimal, to activate more peripherals, see:
+ * http://dts.acmesystems.it/arietta/
+ */
+/dts-v1/;
+#include "at91sam9g25.dtsi"
+/ {
+	model = "Acme Systems Arietta G25";
+	compatible = "acme,ariettag25", "atmel,at91sam9x5", "atmel,at91sam9";
+
+	aliases {
+		serial0 = &dbgu;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0x20000000 0x8000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			mmc0: mmc@f0008000 {
+				pinctrl-0 = <
+				  &pinctrl_mmc0_slot0_clk_cmd_dat0
+				  &pinctrl_mmc0_slot0_dat1_3>;
+				status = "okay";
+
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+				};
+			};
+
+			usb2: gadget@f803c000 {
+				status = "okay";
+			};
+
+			dbgu: serial@fffff200 {
+				status = "okay";
+			};
+
+			rtc@fffffeb0 {
+				status = "okay";
+			};
+		};
+
+		usb0: ohci@00600000 {
+			status = "okay";
+			num-ports = <3>;
+		};
+
+		usb1: ehci@00700000 {
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		arietta_led {
+			label = "arietta_led";
+			gpios = <&pioB 8 GPIO_ACTIVE_HIGH>; /* PB8 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};

arch/arm/boot/dts/at91-kizbox.dts

@@ -0,0 +1,159 @@
+/*
+ * at91-kizbox.dts - Device Tree file for Overkiz Kizbox board
+ *
+ * Copyright (C) 2012-2014 Boris BREZILLON <b.brezillon@overkiz.com>
+ *               2014-2015 Gaël PORTAY <g.portay@overkiz.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "at91sam9g20.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Overkiz Kizbox";
+	compatible = "overkiz,kizbox", "atmel,at91sam9g20", "atmel,at91sam9";
+
+	chosen {
+		bootargs = "ubi.mtd=ubi";
+		stdout-path = &dbgu;
+	};
+
+	memory {
+		reg = <0x20000000 0x2000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		main_clock: clock@0 {
+			compatible = "atmel,osc", "fixed-clock";
+			clock-frequency = <18432000>;
+		};
+
+		main_xtal {
+			clock-frequency = <18432000>;
+		};
+	};
+
+	ahb {
+		apb {
+			macb0: ethernet@fffc4000 {
+				phy-mode = "mii";
+				pinctrl-0 = <&pinctrl_macb_rmii
+				             &pinctrl_macb_rmii_mii_alt>;
+				status = "okay";
+			};
+
+			usart3: serial@fffd0000 {
+				status = "okay";
+			};
+
+			dbgu: serial@fffff200 {
+				status = "okay";
+			};
+
+			watchdog@fffffd40 {
+				timeout-sec = <15>;
+				atmel,max-heartbeat-sec = <16>;
+				atmel,min-heartbeat-sec = <0>;
+				status = "okay";
+			};
+		};
+
+		usb0: ohci@00500000 {
+			num-ports = <1>;
+			status = "okay";
+		};
+
+		nand0: nand@40000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "soft";
+			status = "okay";
+
+			bootstrap@0 {
+				label = "bootstrap";
+				reg = <0x0 0x20000>;
+			};
+
+			ubi@20000 {
+				label = "ubi";
+				reg = <0x20000 0x7fe0000>;
+			};
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset {
+			label = "PB_RST";
+			gpios = <&pioB 30 GPIO_ACTIVE_HIGH>;
+			linux,code = <0x100>;
+			gpio-key,wakeup;
+		};
+
+		user {
+			label = "PB_USER";
+			gpios = <&pioB 31 GPIO_ACTIVE_HIGH>;
+			linux,code = <0x101>;
+			gpio-key,wakeup;
+		};
+	};
+
+	i2c@0 {
+		status = "okay";
+
+		rtc: pcf8563@51 {
+			compatible = "nxp,pcf8563";
+			reg = <0x51>;
+		};
+	};
+
+	pwm_leds {
+		compatible = "pwm-leds";
+
+		network_green {
+			label = "pwm:green:network";
+			pwms = <&tcb_pwm 2 10000000 PWM_POLARITY_INVERTED>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+
+		network_red {
+			label = "pwm:red:network";
+			pwms = <&tcb_pwm 4 10000000 PWM_POLARITY_INVERTED>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+
+		user_green {
+			label = "pwm:green:user";
+			pwms = <&tcb_pwm 0 10000000 PWM_POLARITY_INVERTED>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+
+		user_red {
+			label = "pwm:red:user";
+			pwms = <&tcb_pwm 1 10000000 PWM_POLARITY_INVERTED>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	tcb_pwm: pwm {
+		compatible = "atmel,tcb-pwm";
+		#pwm-cells = <3>;
+		tc-block = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tcb1_tioa0
+			     &pinctrl_tcb1_tioa1
+			     &pinctrl_tcb1_tioa2
+			     &pinctrl_tcb1_tiob0>;
+	};
+};

arch/arm/boot/dts/at91-kizbox2.dts

@@ -0,0 +1,216 @@
+/*
+ * at91-kizbox2.dts - Device Tree file for Overkiz Kizbox 2 board
+ *
+ * Copyright (C) 2014 Gaël PORTAY <g.portay@overkiz.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "sama5d31.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Overkiz Kizbox 2";
+	compatible = "overkiz,kizbox2", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		bootargs = "ubi.mtd=ubi";
+		stdout-path = &dbgu;
+	};
+
+	memory {
+		reg = <0x20000000 0x10000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			i2c1: i2c@f0018000 {
+				status = "okay";
+
+				pmic: act8865@5b {
+					compatible = "active-semi,act8865";
+					reg = <0x5b>;
+					status = "okay";
+
+					regulators {
+						vcc_1v8_reg: DCDC_REG1 {
+							regulator-name = "VCC_1V8";
+							regulator-min-microvolt = <1800000>;
+							regulator-max-microvolt = <1800000>;
+							regulator-always-on;
+						};
+
+						vcc_1v2_reg: DCDC_REG2 {
+							regulator-name = "VCC_1V2";
+							regulator-min-microvolt = <1200000>;
+							regulator-max-microvolt = <1200000>;
+							regulator-always-on;
+						};
+
+						vcc_3v3_reg: DCDC_REG3 {
+							regulator-name = "VCC_3V3";
+							regulator-min-microvolt = <3300000>;
+							regulator-max-microvolt = <3300000>;
+							regulator-always-on;
+						};
+
+						vddfuse_reg: LDO_REG1 {
+							regulator-name = "FUSE_2V5";
+							regulator-min-microvolt = <2500000>;
+							regulator-max-microvolt = <2500000>;
+						};
+
+						vddana_reg: LDO_REG2 {
+							regulator-name = "VDDANA";
+							regulator-min-microvolt = <3300000>;
+							regulator-max-microvolt = <3300000>;
+							regulator-always-on;
+						};
+
+						vled_reg: LDO_REG3 {
+							regulator-name = "VLED";
+							regulator-min-microvolt = <3300000>;
+							regulator-max-microvolt = <3300000>;
+							regulator-always-on;
+						};
+
+						v3v8_rf_reg: LDO_REG4 {
+							regulator-name = "V3V8_RF";
+							regulator-min-microvolt = <3800000>;
+							regulator-max-microvolt = <3800000>;
+							regulator-always-on;
+						};
+					};
+				};
+			};
+
+			usart0: serial@f001c000 {
+				status = "okay";
+			};
+
+			usart1: serial@f0020000 {
+				status = "okay";
+			};
+
+			pwm0: pwm@f002c000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_pwm0_pwmh0_1
+					     &pinctrl_pwm0_pwmh1_1
+					     &pinctrl_pwm0_pwmh2_0>;
+				status = "okay";
+			};
+
+			adc0: adc@f8018000 {
+				atmel,adc-vref = <3333>;
+				status = "okay";
+			};
+
+			usart2: serial@f8020000 {
+				status = "okay";
+			};
+
+			macb1: ethernet@f802c000 {
+				phy-mode = "rmii";
+				status = "okay";
+			};
+
+			dbgu: serial@ffffee00 {
+				status = "okay";
+			};
+
+			watchdog@fffffe40 {
+				status = "okay";
+			};
+		};
+
+		usb1: ohci@00600000 {
+			status = "okay";
+		};
+
+		usb2: ehci@00700000 {
+			status = "okay";
+		};
+
+		nand0: nand@60000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			atmel,has-pmecc;
+			atmel,pmecc-cap = <4>;
+			atmel,pmecc-sector-size = <512>;
+			nand-on-flash-bbt;
+			status = "okay";
+
+			bootstrap@0 {
+				label = "bootstrap";
+				reg = <0x0 0x20000>;
+			};
+
+			ubi@20000 {
+				label = "ubi";
+				reg = <0x20000 0x7fe0000>;
+			};
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		prog {
+			label = "PB_PROG";
+			gpios = <&pioE 27 GPIO_ACTIVE_LOW>;
+			linux,code = <0x102>;
+			gpio-key,wakeup;
+		};
+
+		reset {
+			label = "PB_RST";
+			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
+			linux,code = <0x100>;
+			gpio-key,wakeup;
+		};
+
+		user {
+			label = "PB_USER";
+			gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
+			linux,code = <0x101>;
+			gpio-key,wakeup;
+		};
+	};
+
+	pwm_leds {
+		compatible = "pwm-leds";
+
+		blue {
+			label = "pwm:blue:user";
+			pwms = <&pwm0 2 10000000 0>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+
+		green {
+			label = "pwm:green:user";
+			pwms = <&pwm0 1 10000000 0>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+
+		red {
+			label = "pwm:red:user";
+			pwms = <&pwm0 0 10000000 0>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+	};
+};

arch/arm/boot/dts/at91-kizboxmini.dts

@@ -0,0 +1,129 @@
+/*
+ * at91-kizboxmini.dts - Device Tree file for Overkiz Kizbox mini board
+ *
+ * Copyright (C) 2014 Gaël PORTAY <g.portay@overkiz.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "at91sam9g25.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+	model = "Overkiz Kizbox mini";
+	compatible = "overkiz,kizboxmini", "atmel,at91sam9g25", "atmel,at91sam9x5", "atmel,at91sam9";
+
+	chosen {
+		bootargs = "ubi.mtd=ubi";
+		stdout-path = &dbgu;
+	};
+
+	memory {
+		reg = <0x20000000 0x8000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			usart0: serial@f801c000 {
+				status = "okay";
+			};
+
+			macb0: ethernet@f802c000 {
+				phy-mode = "rmii";
+				status = "okay";
+			};
+
+			pwm0: pwm@f8034000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_pwm0_pwm0_1
+					     &pinctrl_pwm0_pwm1_1>;
+				status = "okay";
+			};
+
+			dbgu: serial@fffff200 {
+				status = "okay";
+			};
+
+			watchdog@fffffe40 {
+				status = "okay";
+			};
+		};
+
+		usb0: ohci@00600000 {
+			num-ports = <1>;
+			status = "okay";
+		};
+
+		usb1: ehci@00700000 {
+			status = "okay";
+		};
+
+		nand0: nand@40000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			atmel,has-pmecc;
+			atmel,pmecc-cap = <4>;
+			atmel,pmecc-sector-size = <512>;
+			nand-on-flash-bbt;
+			status = "okay";
+
+			bootstrap@0 {
+				label = "bootstrap";
+				reg = <0x0 0x20000>;
+			};
+
+			ubi@20000 {
+				label = "ubi";
+				reg = <0x20000 0x7fe0000>;
+			};
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		prog {
+			label = "PB_PROG";
+			gpios = <&pioC 17 GPIO_ACTIVE_LOW>;
+			linux,code = <0x102>;
+			gpio-key,wakeup;
+		};
+
+		reset {
+			label = "PB_RST";
+			gpios = <&pioC 16 GPIO_ACTIVE_LOW>;
+			linux,code = <0x100>;
+			gpio-key,wakeup;
+		};
+	};
+
+	pwm_leds {
+		compatible = "pwm-leds";
+
+		green {
+			label = "pwm:green:user";
+			pwms = <&pwm0 0 10000000 0>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+
+		red {
+			label = "pwm:red:user";
+			pwms = <&pwm0 1 10000000 0>;
+			max-brightness = <255>;
+			linux,default-trigger = "default-on";
+		};
+	};
+};

arch/arm/boot/dts/at91-sama5d3_xplained.dts

@@ -14,7 +14,7 @@
 	compatible = "atmel,sama5d3-xplained", "atmel,sama5d3", "atmel,sama5";
 
 	chosen {
-		bootargs = "console=ttyS0,115200";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
@@ -35,6 +35,8 @@
 		apb {
 			mmc0: mmc@f0000000 {
 				pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_dat4_7 &pinctrl_mmc0_cd>;
+				vmmc-supply = <&vcc_mmc0_reg>;
+				vqmmc-supply = <&vcc_3v3_reg>;
 				status = "okay";
 				slot@0 {
 					reg = <0>;
@@ -43,6 +45,17 @@
 				};
 			};
 
+			mmc1: mmc@f8000000 {
+				vmmc-supply = <&vcc_3v3_reg>;
+				vqmmc-supply = <&vcc_3v3_reg>;
+				status = "disabled";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioE 1 GPIO_ACTIVE_LOW>;
+				};
+			};
+
 			spi0: spi@f0004000 {
 				cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
 				status = "okay";
@@ -105,7 +118,13 @@
 
 			macb0: ethernet@f0028000 {
 				phy-mode = "rgmii";
+				#address-cells = <1>;
+				#size-cells = <0>;
 				status = "okay";
+
+				ethernet-phy@7 {
+					reg = <0x7>;
+				};
 			};
 
 			pwm0: pwm@f002c000 {
@@ -215,12 +234,6 @@
 					};
 				};
 			};
-
-			pmc: pmc@fffffc00 {
-				main: mainck {
-					clock-frequency = <12000000>;
-				};
-			};
 		};
 
 		nand0: nand@60000000 {
@@ -284,6 +297,14 @@
 		};
 	};
 
+	vcc_mmc0_reg: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		gpio = <&pioE 2 GPIO_ACTIVE_LOW>;
+		regulator-name = "mmc0-card-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	gpio_keys {
 		compatible = "gpio-keys";
 

arch/arm/boot/dts/at91-sama5d4_xplained.dts

@@ -50,7 +50,8 @@
 	compatible = "atmel,sama5d4-xplained", "atmel,sama5d4", "atmel,sama5";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 ignore_loglevel earlyprintk";
+		bootargs = "ignore_loglevel earlyprintk";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
@@ -106,6 +107,8 @@
 			mmc1: mmc@fc000000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+				vmmc-supply = <&vcc_mmc1_reg>;
+				vqmmc-supply = <&vcc_3v3_reg>;
 				status = "okay";
 				slot@0 {
 					reg = <0>;
@@ -122,6 +125,11 @@
 				status = "okay";
 			};
 
+			spi1: spi@fc018000 {
+				cs-gpios = <&pioB 21 0>;
+				status = "okay";
+			};
+
 			adc0: adc@fc034000 {
 				atmel,adc-vref = <3300>;
 				status = "okay";
@@ -238,4 +246,22 @@
 			linux,default-trigger = "heartbeat";
 		};
 	};
+
+	vcc_3v3_reg: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC 3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vcc_mmc1_reg: fixedregulator@1 {
+		compatible = "regulator-fixed";
+		gpio = <&pioE 4 GPIO_ACTIVE_LOW>;
+		regulator-name = "VDD MCI1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3_reg>;
+	};
 };

arch/arm/boot/dts/at91-sama5d4ek.dts

@@ -50,7 +50,8 @@
 	compatible = "atmel,sama5d4ek", "atmel,sama5d4", "atmel,sama5";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 ignore_loglevel earlyprintk";
+		bootargs = "ignore_loglevel earlyprintk";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
@@ -108,8 +109,8 @@
 			mmc0: mmc@f8000000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
-				slot@1 {
-					reg = <1>;
+				slot@0 {
+					reg = <0>;
 					bus-width = <4>;
 					cd-gpios = <&pioE 5 0>;
 				};

arch/arm/boot/dts/at91rm9200.dtsi

@@ -940,8 +940,8 @@
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00300000 0x100000>;
 			interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&usb>, <&ohci_clk>, <&ohci_clk>, <&uhpck>;
-			clock-names = "usb_clk", "ohci_clk", "hclk", "uhpck";
+			clocks = <&ohci_clk>, <&ohci_clk>, <&uhpck>;
+			clock-names = "ohci_clk", "hclk", "uhpck";
 			status = "disabled";
 		};
 	};

arch/arm/boot/dts/at91rm9200ek.dts

@@ -12,6 +12,10 @@
 	model = "Atmel AT91RM9200 evaluation kit";
 	compatible = "atmel,at91rm9200ek", "atmel,at91rm9200";
 
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
 	memory {
 		reg = <0x20000000 0x4000000>;
 	};

arch/arm/boot/dts/at91sam9260.dtsi

@@ -1008,8 +1008,8 @@
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00500000 0x100000>;
 			interrupts = <20 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&usb>, <&ohci_clk>, <&ohci_clk>, <&uhpck>;
-			clock-names = "usb_clk", "ohci_clk", "hclk", "uhpck";
+			clocks = <&ohci_clk>, <&ohci_clk>, <&uhpck>;
+			clock-names = "ohci_clk", "hclk", "uhpck";
 			status = "disabled";
 		};
 	};

arch/arm/boot/dts/at91sam9261.dtsi

@@ -75,8 +75,8 @@
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00500000 0x100000>;
 			interrupts = <20 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&usb>, <&ohci_clk>, <&hclk0>, <&uhpck>;
-			clock-names = "usb_clk", "ohci_clk", "hclk", "uhpck";
+			clocks = <&ohci_clk>, <&hclk0>, <&uhpck>;
+			clock-names = "ohci_clk", "hclk", "uhpck";
 			status = "disabled";
 		};
 

arch/arm/boot/dts/at91sam9261ek.dts

@@ -13,7 +13,8 @@
 	compatible = "atmel,at91sam9261ek", "atmel,at91sam9261", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs rw";
+		bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs rw";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {

arch/arm/boot/dts/at91sam9263.dtsi

@@ -1010,8 +1010,8 @@
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00a00000 0x100000>;
 			interrupts = <29 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&usb>, <&ohci_clk>, <&ohci_clk>, <&uhpck>;
-			clock-names = "usb_clk", "ohci_clk", "hclk", "uhpck";
+			clocks = <&ohci_clk>, <&ohci_clk>, <&uhpck>;
+			clock-names = "ohci_clk", "hclk", "uhpck";
 			status = "disabled";
 		};
 	};

arch/arm/boot/dts/at91sam9263ek.dts

@@ -13,7 +13,8 @@
 	compatible = "atmel,at91sam9263ek", "atmel,at91sam9263", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
+		bootargs = "mem=64M root=/dev/mtdblock5 rw rootfstype=ubifs";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {

arch/arm/boot/dts/at91sam9g20ek_common.dtsi

@@ -10,7 +10,8 @@
 / {
 
 	chosen {
-		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs";
+		bootargs = "mem=64M root=/dev/mtdblock5 rw rootfstype=ubifs";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {

arch/arm/boot/dts/at91sam9g45.dtsi

@@ -1291,8 +1291,8 @@
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00700000 0x100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&usb>, <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
-			clock-names = "usb_clk", "ohci_clk", "hclk", "uhpck";
+			clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+			clock-names = "ohci_clk", "hclk", "uhpck";
 			status = "disabled";
 		};
 
@@ -1300,8 +1300,8 @@
 			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 			reg = <0x00800000 0x100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&utmi>, <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
-			clock-names = "usb_clk", "ehci_clk", "hclk", "uhpck";
+			clocks = <&utmi>, <&uhphs_clk>;
+			clock-names = "usb_clk", "ehci_clk";
 			status = "disabled";
 		};
 	};

arch/arm/boot/dts/at91sam9m10g45ek.dts

@@ -15,7 +15,8 @@
 	compatible = "atmel,at91sam9m10g45ek", "atmel,at91sam9g45", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2";
+		bootargs = "mem=64M root=/dev/mtdblock1 rw rootfstype=jffs2";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {

arch/arm/boot/dts/at91sam9n12.dtsi

@@ -949,9 +949,8 @@
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00500000 0x00100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&usb>, <&uhphs_clk>, <&uhphs_clk>,
-				 <&uhpck>;
-			clock-names = "usb_clk", "ohci_clk", "hclk", "uhpck";
+			clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+			clock-names = "ohci_clk", "hclk", "uhpck";
 			status = "disabled";
 		};
 	};

arch/arm/boot/dts/at91sam9n12ek.dts

@@ -14,7 +14,8 @@
 	compatible = "atmel,at91sam9n12ek", "atmel,at91sam9n12", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2";
+		bootargs = "root=/dev/mtdblock1 rw rootfstype=jffs2";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {

arch/arm/boot/dts/at91sam9rl.dtsi

@@ -1065,13 +1065,6 @@
 				};
 			};
 
-			rtc@fffffeb0 {
-				compatible = "atmel,at91rm9200-rtc";
-				reg = <0xfffffeb0 0x40>;
-				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
-				status = "disabled";
-			};
-
 			rtc@fffffd20 {
 				compatible = "atmel,at91sam9260-rtt";
 				reg = <0xfffffd20 0x10>;
@@ -1085,6 +1078,14 @@
 				reg = <0xfffffd60 0x10>;
 				status = "disabled";
 			};
+
+			rtc@fffffe00 {
+				compatible = "atmel,at91rm9200-rtc";
+				reg = <0xfffffe00 0x40>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				status = "disabled";
+			};
+
 		};
 	};
 

arch/arm/boot/dts/at91sam9rlek.dts

@@ -13,7 +13,8 @@
 	compatible = "atmel,at91sam9rlek", "atmel,at91sam9rl", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 rootfstype=ubifs root=ubi0:rootfs ubi.mtd=5 rw";
+		bootargs = "rootfstype=ubifs root=ubi0:rootfs ubi.mtd=5 rw";
+		stdout-path = "serial0:115200n8";
 	};
 
 	memory {
@@ -181,13 +182,11 @@
 				};
 			};
 
-			pmc: pmc@fffffc00 {
-				main: mainck {
-					clock-frequency = <12000000>;
-				};
+			watchdog@fffffd40 {
+				status = "okay";
 			};
 
-			watchdog@fffffd40 {
+			rtc@fffffe00 {
 				status = "okay";
 			};
 		};

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -505,7 +505,7 @@
 
 					pinctrl_usart1_sck: usart1_sck-0 {
 						atmel,pins =
-							<AT91_PIOC 28 AT91_PERIPH_C AT91_PINCTRL_NONE>;	/* PC29 periph C */
+							<AT91_PIOC 29 AT91_PERIPH_C AT91_PINCTRL_NONE>;	/* PC29 periph C */
 					};
 				};
 
@@ -694,6 +694,52 @@
 					};
 				};
 
+				pwm0 {
+					pinctrl_pwm0_pwm0_0: pwm0_pwm0-0 {
+						atmel,pins =
+							<AT91_PIOB 11 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+					};
+					pinctrl_pwm0_pwm0_1: pwm0_pwm0-1 {
+						atmel,pins =
+							<AT91_PIOC 10 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+					pinctrl_pwm0_pwm0_2: pwm0_pwm0-2 {
+						atmel,pins =
+							<AT91_PIOC 18 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_pwm0_pwm1_0: pwm0_pwm1-0 {
+						atmel,pins =
+							<AT91_PIOB 12 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+					};
+					pinctrl_pwm0_pwm1_1: pwm0_pwm1-1 {
+						atmel,pins =
+							<AT91_PIOC 11 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+					pinctrl_pwm0_pwm1_2: pwm0_pwm1-2 {
+						atmel,pins =
+							<AT91_PIOC 19 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_pwm0_pwm2_0: pwm0_pwm2-0 {
+						atmel,pins =
+							<AT91_PIOB 13 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+					};
+					pinctrl_pwm0_pwm2_1: pwm0_pwm2-1 {
+						atmel,pins =
+							<AT91_PIOC 20 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+
+					pinctrl_pwm0_pwm3_0: pwm0_pwm3-0 {
+						atmel,pins =
+							<AT91_PIOB 14 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+					};
+					pinctrl_pwm0_pwm3_1: pwm0_pwm3-1 {
+						atmel,pins =
+							<AT91_PIOC 21 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+				};
+
 				tcb0 {
 					pinctrl_tcb0_tclk0: tcb0_tclk0-0 {
 						atmel,pins = <AT91_PIOA 24 AT91_PERIPH_A AT91_PINCTRL_NONE>;
@@ -1176,8 +1222,8 @@
 			compatible = "atmel,at91rm9200-ohci", "usb-ohci";
 			reg = <0x00600000 0x100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&usb>, <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
-			clock-names = "usb_clk", "ohci_clk", "hclk", "uhpck";
+			clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+			clock-names = "ohci_clk", "hclk", "uhpck";
 			status = "disabled";
 		};
 
@@ -1185,8 +1231,8 @@
 			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 			reg = <0x00700000 0x100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&utmi>, <&uhphs_clk>, <&uhpck>;
-			clock-names = "usb_clk", "ehci_clk", "uhpck";
+			clocks = <&utmi>, <&uhphs_clk>;
+			clock-names = "usb_clk", "ehci_clk";
 			status = "disabled";
 		};
 	};

arch/arm/boot/dts/at91sam9x5ek.dtsi

@@ -13,7 +13,8 @@
 	compatible = "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
 
 	chosen {
-		bootargs = "console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
+		bootargs = "root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
+		stdout-path = "serial0:115200n8";
 	};
 
 	ahb {

arch/arm/boot/dts/axp209.dtsi

@@ -18,11 +18,6 @@
  *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  *     GNU General Public License for more details.
  *
- *     You should have received a copy of the GNU General Public
- *     License along with this file; if not, write to the Free
- *     Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
- *     MA 02110-1301 USA
- *
  * Or, alternatively,
  *
  *  b) Permission is hereby granted, free of charge, to any person

arch/arm/boot/dts/bcm-cygnus.dtsi

@@ -212,6 +212,18 @@
 		status = "disabled";
 	};
 
+	nand: nand@18046000 {
+		compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1", "brcm,brcmnand";
+		reg = <0x18046000 0x600>, <0xf8105408 0x600>, <0x18046f00 0x20>;
+		reg-names = "nand", "iproc-idm", "iproc-ext";
+		interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		brcm,nand-has-wp;
+	};
+
 	gic: interrupt-controller@19021000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;

arch/arm/boot/dts/bcm2835-rpi-b-plus.dts

@@ -1,5 +1,5 @@
 /dts-v1/;
-/include/ "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi.dtsi"
 
 / {
 	compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
@@ -25,6 +25,6 @@
 	/* I2S interface */
 	i2s_alt0: i2s_alt0 {
 		brcm,pins = <18 19 20 21>;
-		brcm,function = <4>; /* alt0 */
+		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
 };

arch/arm/boot/dts/bcm2835-rpi-b.dts

@@ -1,5 +1,5 @@
 /dts-v1/;
-/include/ "bcm2835-rpi.dtsi"
+#include "bcm2835-rpi.dtsi"
 
 / {
 	compatible = "raspberrypi,model-b", "brcm,bcm2835";
@@ -18,6 +18,6 @@
 	/* I2S interface */
 	i2s_alt2: i2s_alt2 {
 		brcm,pins = <28 29 30 31>;
-		brcm,function = <6>; /* alt2 */
+		brcm,function = <BCM2835_FSEL_ALT2>;
 	};
 };

arch/arm/boot/dts/bcm2835-rpi.dtsi

@@ -1,4 +1,4 @@
-/include/ "bcm2835.dtsi"
+#include "bcm2835.dtsi"
 
 / {
 	memory {
@@ -21,17 +21,17 @@
 
 	gpioout: gpioout {
 		brcm,pins = <6>;
-		brcm,function = <1>; /* GPIO out */
+		brcm,function = <BCM2835_FSEL_GPIO_OUT>;
 	};
 
 	alt0: alt0 {
 		brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 14 15 40 45>;
-		brcm,function = <4>; /* alt0 */
+		brcm,function = <BCM2835_FSEL_ALT0>;
 	};
 
 	alt3: alt3 {
 		brcm,pins = <48 49 50 51 52 53>;
-		brcm,function = <7>; /* alt3 */
+		brcm,function = <BCM2835_FSEL_ALT3>;
 	};
 };
 

arch/arm/boot/dts/bcm2835.dtsi

@@ -1,4 +1,5 @@
-/include/ "skeleton.dtsi"
+#include <dt-bindings/pinctrl/bcm2835.h>
+#include "skeleton.dtsi"
 
 / {
 	compatible = "brcm,bcm2835";
@@ -14,6 +15,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x7e000000 0x20000000 0x02000000>;
+		dma-ranges = <0x40000000 0x00000000 0x20000000>;
 
 		timer@7e003000 {
 			compatible = "brcm,bcm2835-system-timer";
@@ -60,6 +62,13 @@
 			reg = <0x7e104000 0x10>;
 		};
 
+		mailbox: mailbox@7e00b800 {
+			compatible = "brcm,bcm2835-mbox";
+			reg = <0x7e00b880 0x40>;
+			interrupts = <0 1>;
+			#mbox-cells = <0>;
+		};
+
 		gpio: gpio@7e200000 {
 			compatible = "brcm,bcm2835-gpio";
 			reg = <0x7e200000 0xb4>;
@@ -112,7 +121,7 @@
 			status = "disabled";
 		};
 
-		i2c0: i2c@20205000 {
+		i2c0: i2c@7e205000 {
 			compatible = "brcm,bcm2835-i2c";
 			reg = <0x7e205000 0x1000>;
 			interrupts = <2 21>;

arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts

@@ -0,0 +1,97 @@
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Asus RT-AC56U
+ *
+ * Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "asus,rt-ac56u", "brcm,bcm4708";
+	model = "Asus RT-AC56U (BCM4708)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		usb3 {
+			label = "bcm53xx:blue:usb3";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		wan {
+			label = "bcm53xx:blue:wan";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		lan {
+			label = "bcm53xx:blue:lan";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		power {
+			label = "bcm53xx:blue:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		all {
+			label = "bcm53xx:blue:all";
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		2ghz {
+			label = "bcm53xx:blue:2ghz";
+			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+
+		usb2 {
+			label = "bcm53xx:blue:usb2";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};

arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts

@@ -0,0 +1,84 @@
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Asus RT-AC68U
+ *
+ * Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "asus,rt-ac68u", "brcm,bcm4708";
+	model = "Asus RT-AC68U (BCM4708)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		usb2 {
+			label = "bcm53xx:blue:usb2";
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		power {
+			label = "bcm53xx:blue:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		logo {
+			label = "bcm53xx:white:logo";
+			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		usb3 {
+			label = "bcm53xx:blue:usb3";
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		brightness {
+			label = "Backlight";
+			linux,code = <KEY_BRIGHTNESS_ZERO>;
+			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};

arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts

@@ -10,6 +10,7 @@
 /dts-v1/;
 
 #include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
 
 / {
 	compatible = "buffalo,wzr-1750dhp", "brcm,bcm4708";
@@ -47,6 +48,12 @@
 	leds {
 		compatible = "gpio-leds";
 
+		usb {
+			label = "bcm53xx:blue:usb";
+			gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
 		power0 {
 			label = "bcm53xx:red:power";
 			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;

arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts

@@ -10,6 +10,7 @@
 /dts-v1/;
 
 #include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
 
 / {
 	compatible = "luxul,xwc-1000", "brcm,bcm4708";
@@ -23,12 +24,8 @@
 		reg = <0x00000000 0x08000000>;
 	};
 
-	axi@18000000 {
-		nand@28000 {
-			reg = <0x00028000 0x1000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-
+	nand: nand@18028000 {
+		nandcs@0 {
 			partition@0 {
 				label = "ubi";
 				reg = <0x00000000 0x08000000>;

arch/arm/boot/dts/bcm4708-netgear-r6250.dts

@@ -10,6 +10,7 @@
 /dts-v1/;
 
 #include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
 
 / {
 	compatible = "netgear,r6250v1", "brcm,bcm4708";

arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts

@@ -10,6 +10,7 @@
 /dts-v1/;
 
 #include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
 
 / {
 	compatible = "netgear,r6300v2", "brcm,bcm4708";

arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts

@@ -0,0 +1,120 @@
+/*
+ * Broadcom BCM470X / BCM5301X arm platform code.
+ * DTS for SmartRG SR400ac
+ *
+ * Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "smartrg,sr400ac", "brcm,bcm4708";
+	model = "SmartRG SR400ac";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		power-white {
+			label = "bcm53xx:white:power";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		power-amber {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		usb2 {
+			label = "bcm53xx:white:usb2";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		usb3-white {
+			label = "bcm53xx:white:usb3";
+			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		usb3-green {
+			label = "bcm53xx:green:usb3";
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		wps {
+			label = "bcm53xx:white:wps";
+			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		status-red {
+			label = "bcm53xx:red:status";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		status-green {
+			label = "bcm53xx:green:status";
+			gpios = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		status-blue {
+			label = "bcm53xx:blue:status";
+			gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		wan-white {
+			label = "bcm53xx:white:wan";
+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		wan-red {
+			label = "bcm53xx:red:wan";
+			gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rfkill {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
+		};
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
+		};
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};

arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts

@@ -10,6 +10,7 @@
 /dts-v1/;
 
 #include "bcm47081.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
 
 / {
 	compatible = "asus,rt-n18u", "brcm,bcm47081", "brcm,bcm4708";

arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts

@@ -10,6 +10,7 @@
 /dts-v1/;
 
 #include "bcm47081.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
 
 / {
 	compatible = "buffalo,wzr-600dhp2", "brcm,bcm47081", "brcm,bcm4708";

arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts

@@ -10,6 +10,7 @@
 /dts-v1/;
 
 #include "bcm47081.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
 
 / {
 	compatible = "buffalo,wzr-900dhp", "brcm,bcm47081", "brcm,bcm4708";

arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts

@@ -0,0 +1,65 @@
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Asus RT-AC87U
+ *
+ * Copyright (C) 2015 Rafał Miłecki <zajec5@gmail.com>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+
+/ {
+	compatible = "asus,rt-ac87u", "brcm,bcm4709", "brcm,bcm4708";
+	model = "Asus RT-AC87U";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		wps {
+			label = "bcm53xx:blue:wps";
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+
+		power {
+			label = "bcm53xx:blue:power";
+			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		wan {
+			label = "bcm53xx:red:wan";
+			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
+		};
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};

arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts

@@ -0,0 +1,128 @@
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Buffalo WXR-1900DHP
+ *
+ * Copyright (C) 2015 Felix Fietkau <nbd@openwrt.org>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+
+/ {
+	compatible = "buffalo,wxr-1900dhp", "brcm,bcm4709", "brcm,bcm4708";
+	model = "Buffalo WXR-1900DHP";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		usb {
+			label = "bcm53xx:green:usb";
+			gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		power-amber {
+			label = "bcm53xx:amber:power";
+			gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		power-white {
+			label = "bcm53xx:white:power";
+			gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		router-amber {
+			label = "bcm53xx:amber:router";
+			gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		router-white {
+			label = "bcm53xx:white:router";
+			gpios = <&chipcommon 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		wan-amber {
+			label = "bcm53xx:amber:wan";
+			gpios = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		wan-white {
+			label = "bcm53xx:white:wan";
+			gpios = <&chipcommon 10 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		wireless-amber {
+			label = "bcm53xx:amber:wireless";
+			gpios = <&chipcommon 11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+
+		wireless-white {
+			label = "bcm53xx:white:wireless";
+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-off";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		power {
+			label = "Power";
+			linux,code = <KEY_POWER>;
+			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
+		};
+
+		restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+
+		aoss {
+			label = "AOSS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Commit mode set by switch? */
+		mode {
+			label = "Mode";
+			linux,code = <KEY_SETUP>;
+			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Switch: AP mode */
+		sw_ap {
+			label = "AP";
+			linux,code = <BTN_0>;
+			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
+		};
+
+		eject {
+			label = "USB eject";
+			linux,code = <KEY_EJECTCD>;
+			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
+		};
+	};
+};

arch/arm/boot/dts/bcm4709-netgear-r8000.dts

@@ -10,6 +10,7 @@
 /dts-v1/;
 
 #include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
 
 / {
 	compatible = "netgear,r8000", "brcm,bcm4709", "brcm,bcm4708";

arch/arm/boot/dts/bcm5301x-nand-cs0-bch8.dtsi

@@ -0,0 +1,24 @@
+/*
+ * Broadcom BCM470X / BCM5301X Nand chip defaults.
+ *
+ * This should be included if the NAND controller is on chip select 0
+ * and uses 8 bit ECC.
+ *
+ * Copyright (C) 2015 Hauke Mehrtens <hauke@hauke-m.de>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/ {
+	nand@18028000 {
+		nandcs@0 {
+			compatible = "brcm,nandcs";
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			nand-ecc-strength = <8>;
+			nand-ecc-step-size = <512>;
+		};
+	};
+};

arch/arm/boot/dts/bcm5301x.dtsi

@@ -108,6 +108,30 @@
 			/* ChipCommon */
 			<0x00000000 0 &gic GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
 
+			/* PCIe Controller 0 */
+			<0x00012000 0 &gic GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00012000 1 &gic GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00012000 2 &gic GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00012000 3 &gic GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00012000 4 &gic GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00012000 5 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* PCIe Controller 1 */
+			<0x00013000 0 &gic GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00013000 1 &gic GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00013000 2 &gic GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00013000 3 &gic GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00013000 4 &gic GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00013000 5 &gic GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+
+			/* PCIe Controller 2 */
+			<0x00014000 0 &gic GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00014000 1 &gic GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00014000 2 &gic GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00014000 3 &gic GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00014000 4 &gic GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+			<0x00014000 5 &gic GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
+
 			/* USB 2.0 Controller */
 			<0x00021000 0 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
 
@@ -143,4 +167,16 @@
 			#gpio-cells = <2>;
 		};
 	};
+
+	nand: nand@18028000 {
+		compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1", "brcm,brcmnand";
+		reg = <0x18028000 0x600>, <0x1811a408 0x600>, <0x18028f00 0x20>;
+		reg-names = "nand", "iproc-idm", "iproc-ext";
+		interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		brcm,nand-has-wp;
+	};
 };

arch/arm/boot/dts/bcm63138.dtsi

@@ -26,6 +26,7 @@
 			compatible = "arm,cortex-a9";
 			next-level-cache = <&L2>;
 			reg = <0>;
+			enable-method = "brcm,bcm63138";
 		};
 
 		cpu@1 {
@@ -33,6 +34,8 @@
 			compatible = "arm,cortex-a9";
 			next-level-cache = <&L2>;
 			reg = <1>;
+			enable-method = "brcm,bcm63138";
+			resets = <&pmb0 4 1>;
 		};
 	};
 
@@ -105,6 +108,18 @@
 			reg = <0x1e620 0x20>;
 			interrupts = <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>;
 		};
+
+		pmb0: reset-controller@4800c0 {
+			compatible = "brcm,bcm63138-pmb";
+			reg = <0x4800c0 0x10>;
+			#reset-cells = <2>;
+		};
+
+		pmb1: reset-controller@4800e0 {
+			compatible = "brcm,bcm63138-pmb";
+			reg = <0x4800e0 0x10>;
+			#reset-cells = <2>;
+		};
 	};
 
 	/* Legacy UBUS base */
@@ -114,6 +129,11 @@
 		#size-cells = <1>;
 		ranges = <0 0xfffe8000 0x8100>;
 
+		timer: timer@80 {
+			compatible = "brcm,bcm6328-timer", "syscon";
+			reg = <0x80 0x3c>;
+		};
+
 		serial0: serial@600 {
 			compatible = "brcm,bcm6345-uart";
 			reg = <0x600 0x1b>;
@@ -131,5 +151,28 @@
 			clock-names = "periph";
 			status = "disabled";
 		};
+
+		nand: nand@2000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.0", "brcm,brcmnand";
+			reg = <0x2000 0x600>, <0xf0 0x10>;
+			reg-names = "nand", "nand-int-base";
+			status = "disabled";
+			interrupts = <GIC_SPI 38 0>;
+			interrupt-names = "nand";
+		};
+
+		bootlut: bootlut@8000 {
+			compatible = "brcm,bcm63138-bootlut";
+			reg = <0x8000 0x50>;
+		};
+
+		reboot {
+			compatible = "syscon-reboot";
+			regmap = <&timer>;
+			offset = <0x34>;
+			mask = <1>;
+		};
 	};
 };

arch/arm/boot/dts/bcm7445-bcm97445svmb.dts

@@ -12,3 +12,26 @@
 		      <0x00 0x80000000 0x00 0x40000000>;
 	};
 };
+
+&nand {
+	status = "okay";
+
+	nandcs@1 {
+		compatible = "brcm,nandcs";
+		reg = <1>;
+		nand-ecc-step-size = <512>;
+		nand-ecc-strength = <8>;
+		nand-on-flash-bbt;
+
+		#size-cells = <2>;
+		#address-cells = <2>;
+
+		flash1.rootfs0@0 {
+			reg = <0x0 0x0 0x0 0x80000000>;
+		};
+
+		flash1.rootfs1@80000000 {
+			reg = <0x0 0x80000000 0x0 0x80000000>;
+		};
+	};
+};

arch/arm/boot/dts/bcm7445.dtsi

@@ -108,6 +108,65 @@
 			brcm,int-map-mask = <0x25c>, <0x7000000>;
 			brcm,int-fwd-mask = <0x70000>;
 		};
+
+		hif_intr2_intc: interrupt-controller@3e1000 {
+			compatible = "brcm,l2-intc";
+			reg = <0x3e1000 0x30>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+			interrupts = <GIC_SPI 0x20 0x0>;
+			interrupt-parent = <&gic>;
+			interrupt-names = "hif";
+		};
+
+		nand: nand@3e2800 {
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,brcmnand-v7.1", "brcm,brcmnand";
+			reg-names = "nand", "flash-dma";
+			reg = <0x3e2800 0x600>, <0x3e3000 0x2c>;
+			interrupt-parent = <&hif_intr2_intc>;
+			interrupts = <24>, <4>;
+			interrupt-names = "nand_ctlrdy", "flash_dma_done";
+		};
+
+		sata@45a000 {
+			compatible = "brcm,bcm7445-ahci", "brcm,sata3-ahci";
+			reg-names = "ahci", "top-ctrl";
+			reg = <0x45a000 0xa9c>, <0x458040 0x24>;
+			interrupts = <GIC_SPI 30 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			sata0: sata-port@0 {
+				reg = <0>;
+				phys = <&sata_phy0>;
+			};
+
+			sata1: sata-port@1 {
+				reg = <1>;
+				phys = <&sata_phy1>;
+			};
+		};
+
+		sata_phy: sata-phy@458100 {
+			compatible = "brcm,bcm7445-sata-phy", "brcm,phy-sata3";
+			reg = <0x458100 0x1f00>;
+			reg-names = "phy";
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+
+			sata_phy0: sata-phy@0 {
+				reg = <0>;
+				#phy-cells = <0>;
+			};
+
+			sata_phy1: sata-phy@1 {
+				reg = <1>;
+				#phy-cells = <0>;
+			};
+		};
 	};
 
 	smpboot {

arch/arm/boot/dts/bcm958300k.dts

@@ -58,4 +58,20 @@
 	uart3: serial@18023000 {
 		status = "okay";
 	};
+
+	nand: nand@18046000 {
+		nandcs@1 {
+			compatible = "brcm,nandcs";
+			reg = <0>;
+			nand-on-flash-bbt;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			nand-ecc-strength = <24>;
+			nand-ecc-step-size = <1024>;
+
+			brcm,nand-oob-sector-size = <27>;
+		};
+	};
 };

arch/arm/boot/dts/bcm963138dvt.dts

@@ -28,3 +28,15 @@
 &serial1 {
 	status = "okay";
 };
+
+&nand {
+	status = "okay";
+
+	nandcs@0 {
+		compatible = "brcm,nandcs";
+		reg = <0>;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		brcm,nand-oob-sectors-size = <16>;
+	};
+};