ARM: hisi: revert changes from hisi/hip04-dt branch

This backs out all changes that were added in the hip04-dt
branch after various boot problems were discovered in UEFI booting.

Reported-by: Tyler Baker <tyler.baker@linaro.org>
Cc: Wei Xu <xuwei5@hisilicon.com>
[khilman: minor changelog updates]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@linaro.org>

arch/arm/boot/dts/hip04-d01.dts

@@ -28,32 +28,5 @@
 		uart0: uart@4007000 {
 			status = "ok";
 		};
-
-		nand: nand@4020000 {
-			nand-bus-width = <8>;
-			nand-ecc-mode = "hw";
-			nand-ecc-strength = <16>;
-			nand-ecc-step-size = <1024>;
-
-			partition@0 {
-				label = "nand_text";
-				reg = <0x00000000 0x00400000>;
-			};
-
-			partition@00400000 {
-				label = "nand_monitor";
-				reg = <0x00400000 0x00400000>;
-			};
-
-			partition@00800000 {
-				label = "nand_kernel";
-				reg = <0x00800000 0x00800000>;
-			};
-
-			partition@01000000 {
-				label = "nand_fs";
-				reg = <0x01000000 0x1f000000>;
-			};
-		};
 	};
 };

arch/arm/boot/dts/hip04.dtsi

@@ -269,139 +269,6 @@
 			interrupts = <0 372 4>;
 		};
 
-		gpio@4003000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "snps,dw-apb-gpio";
-			reg = <0x4003000 0x1000>;
-
-			gpio3: gpio-controller@0 {
-				compatible = "snps,dw-apb-gpio-port";
-				gpio-controller;
-				#gpio-cells = <2>;
-				snps,nr-gpios = <32>;
-				reg = <0>;
-				interrupt-parent = <&gic>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				interrupts = <0 392 4>;
-			};
-		};
-
-		gpio@4002000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "snps,dw-apb-gpio";
-			reg = <0x4002000 0x1000>;
-
-			gpio2: gpio-controller@0 {
-			compatible = "snps,dw-apb-gpio-port";
-				gpio-controller;
-				#gpio-cells = <2>;
-				snps,nr-gpios = <32>;
-				reg = <0>;
-				interrupt-parent = <&gic>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				interrupts = <0 391 4>;
-			};
-		};
-
-		gpio@4001000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "snps,dw-apb-gpio";
-			reg = <0x4001000 0x1000>;
-
-			gpio1: gpio-controller@0 {
-				compatible = "snps,dw-apb-gpio-port";
-				gpio-controller;
-				#gpio-cells = <2>;
-				snps,nr-gpios = <32>;
-				reg = <0>;
-				interrupt-parent = <&gic>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				interrupts = <0 390 4>;
-			};
-		};
-
-		gpio@4000000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "snps,dw-apb-gpio";
-			reg = <0x4000000 0x1000>;
-
-			gpio0: gpio-controller@0 {
-				compatible = "snps,dw-apb-gpio-port";
-				gpio-controller;
-				#gpio-cells = <2>;
-				snps,nr-gpios = <32>;
-				reg = <0>;
-				interrupt-parent = <&gic>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				interrupts = <0 389 4>;
-			};
-		};
-
-		nand: nand@4020000 {
-			compatible = "hisilicon,504-nfc";
-			reg = <0x4020000 0x10000>, <0x5000000 0x1000>;
-			interrupts = <0 379 4>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-		};
-
-		mdio {
-			compatible = "hisilicon,hip04-mdio";
-			reg = <0x28f1000 0x1000>;
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			phy0: ethernet-phy@0 {
-				compatible = "ethernet-phy-ieee802.3-c22";
-				reg = <0>;
-				marvell,reg-init = <18 0x14 0 0x8001>;
-			};
-
-			phy1: ethernet-phy@1 {
-				compatible = "ethernet-phy-ieee802.3-c22";
-				reg = <1>;
-				marvell,reg-init = <18 0x14 0 0x8001>;
-			};
-		};
-
-		ppe: ppe@28c0000 {
-			compatible = "hisilicon,hip04-ppe", "syscon";
-			reg = <0x28c0000 0x10000>;
-		};
-
-		fe: ethernet@28b0000 {
-			compatible = "hisilicon,hip04-mac";
-			reg = <0x28b0000 0x10000>;
-			interrupts = <0 413 4>;
-			phy-mode = "mii";
-			port-handle = <&ppe 31 0>;
-		};
-
-		ge0: ethernet@2800000 {
-			compatible = "hisilicon,hip04-mac";
-			reg = <0x2800000 0x10000>;
-			interrupts = <0 402 4>;
-			phy-mode = "sgmii";
-			port-handle = <&ppe 0 1>;
-			phy-handle = <&phy0>;
-		};
-
-		ge8: ethernet@2880000 {
-			compatible = "hisilicon,hip04-mac";
-			reg = <0x2880000 0x10000>;
-			interrupts = <0 410 4>;
-			phy-mode = "sgmii";
-			port-handle = <&ppe 8 2>;
-			phy-handle = <&phy1>;
-		};
 	};
 
 	etb@0,e3c42000 {