Merge tag 'sunxi-dt-for-4.9-3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/late

Pull "Allwinner DT changes for 4.9, late edition" from Maxime Ripard:

Here is a bunch of late changes for the 4.9 merge window, mostly:
  - Added a bunch of touchscreens nodes to tablets
  - Added support for the AXP806 PMIC found in the A80 boards
  - Enabled a few pinmux options for the H3

* tag 'sunxi-dt-for-4.9-3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
  ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
  ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
  ARM: dts: sun8i: add pinmux for UART1 at PG
  dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
  dts: sun8i-h3: add pinmux definitions for I2C0-2
  dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
  dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
  dts: sun8i-h3: add pinmux definitions for UART2-3
  ARM: dts: sun9i: a80-optimus: Disable EHCI1
  ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
  ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
  ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
  ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
  ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
  ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h

arch/arm/boot/dts/sun8i-a23-a33.dtsi

@@ -279,6 +279,16 @@
 				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 			};
 
+			uart1_pins_a: uart1@0 {
+				allwinner,pins = "PG6", "PG7";
+				allwinner,function = "uart1";
+			};
+
+			uart1_pins_cts_rts_a: uart1-cts-rts@0 {
+				allwinner,pins = "PG8", "PG9";
+				allwinner,function = "uart1";
+			};
+
 			mmc0_pins_a: mmc0@0 {
 				allwinner,pins = "PF0", "PF1", "PF2",
 						 "PF3", "PF4", "PF5";

arch/arm/boot/dts/sun8i-a23-gt90h-v4.dts

@@ -53,6 +53,15 @@
 	status = "okay";
 };
 
+&touchscreen {
+	reg = <0x40>;
+	compatible = "silead,gsl3675";
+	firmware-name = "gsl3675-gt90h.fw";
+	touchscreen-size-x = <1792>;
+	touchscreen-size-y = <1024>;
+	status = "okay";
+};
+
 &lradc {
 	button@600 {
 		label = "Back";

arch/arm/boot/dts/sun8i-a23-inet86dz.dts

@@ -53,6 +53,15 @@
 	status = "okay";
 };
 
+&touchscreen {
+	reg = <0x40>;
+	compatible = "silead,gsl1680";
+	firmware-name = "gsl1680-inet86dz.fw";
+	touchscreen-size-x = <960>;
+	touchscreen-size-y = <640>;
+	status = "okay";
+};
+
 &usbphy {
 	usb1_vbus-supply = <&reg_dldo1>;
 };

arch/arm/boot/dts/sun8i-a23-polaroid-mid2407pxe03.dts

@@ -62,6 +62,13 @@
 	};
 };
 
+&i2c1 {
+	mma7660: accelerometer@4c {
+		reg = <0x4c>;
+		compatible = "fsl,mma7660";
+	};
+};
+
 &mmc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins_a>;
@@ -90,3 +97,22 @@
 		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
 };
+
+&reg_ldo_io1 {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-touchscreen";
+	status = "okay";
+};
+
+&touchscreen {
+	reg = <0x40>;
+	compatible = "silead,gsl1680";
+	firmware-name = "gsl1680-polaroid-mid2407pxe03.fw";
+	touchscreen-size-x = <960>;
+	touchscreen-size-y = <640>;
+	touchscreen-inverted-x;
+	touchscreen-inverted-y;
+	vddio-supply = <&reg_ldo_io1>;
+	status = "okay";
+};

arch/arm/boot/dts/sun8i-a23-polaroid-mid2809pxe04.dts

@@ -90,3 +90,12 @@
 		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
 };
+
+&touchscreen {
+	reg = <0x40>;
+	compatible = "silead,gsl3670";
+	firmware-name = "gsl3670-polaroid-mid2809pxe04.fw";
+	touchscreen-size-x = <1660>;
+	touchscreen-size-y = <890>;
+	status = "okay";
+};

arch/arm/boot/dts/sun8i-a33-ga10h-v1.1.dts

@@ -58,6 +58,16 @@
 	status = "okay";
 };
 
+&touchscreen {
+	reg = <0x40>;
+	compatible = "silead,gsl3675";
+	firmware-name = "gsl3675-ga10h.fw";
+	touchscreen-size-x = <1630>;
+	touchscreen-size-y = <990>;
+	touchscreen-inverted-y;
+	status = "okay";
+};
+
 &lradc {
 	button@600 {
 		label = "Back";

arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts

@@ -49,6 +49,15 @@
 	model = "INet-D978 Rev 02";
 	compatible = "primux,inet-d978-rev2", "allwinner,sun8i-a33";
 
+	aliases {
+		serial0 = &uart1;
+	};
+
+	chosen {
+		/* Delete debug UART as serial0 is the UART for bluetooth */
+		/delete-property/stdout-path;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -86,3 +95,14 @@
 		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
 };
+
+&r_uart {
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins_a>,
+		    <&uart1_pins_cts_rts_a>;
+	status = "okay";
+};

arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts

@@ -185,7 +185,7 @@
 
 &uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart1_pins_a>;
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
 	status = "okay";
 };
 

arch/arm/boot/dts/sun8i-h3-orangepi-2.dts

@@ -186,6 +186,24 @@
 	status = "okay";
 };
 
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "disabled";
+};
+
 &usb1_vbus_pin_a {
 	allwinner,pins = "PG13";
 };

arch/arm/boot/dts/sun8i-h3-orangepi-one.dts

@@ -139,6 +139,24 @@
 	status = "okay";
 };
 
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "disabled";
+};
+
 &usbphy {
 	/* USB VBUS is always on */
 	status = "okay";

arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts

@@ -161,6 +161,24 @@
 	status = "okay";
 };
 
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "disabled";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "disabled";
+};
+
 &usbphy {
 	/* USB VBUS is always on */
 	status = "okay";

arch/arm/boot/dts/sun8i-h3.dtsi

@@ -327,6 +327,27 @@
 			interrupt-controller;
 			#interrupt-cells = <3>;
 
+			i2c0_pins: i2c0 {
+				allwinner,pins = "PA11", "PA12";
+				allwinner,function = "i2c0";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			i2c1_pins: i2c1 {
+				allwinner,pins = "PA18", "PA19";
+				allwinner,function = "i2c1";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			i2c2_pins: i2c2 {
+				allwinner,pins = "PE12", "PE13";
+				allwinner,function = "i2c2";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
 			mmc0_pins_a: mmc0@0 {
 				allwinner,pins = "PF0", "PF1", "PF2", "PF3",
 						 "PF4", "PF5";
@@ -367,12 +388,33 @@
 				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 			};
 
-			uart1_pins_a: uart1@0 {
-				allwinner,pins = "PG6", "PG7", "PG8", "PG9";
+			uart1_pins: uart1 {
+				allwinner,pins = "PG6", "PG7";
+				allwinner,function = "uart1";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			uart1_rts_cts_pins: uart1_rts_cts {
+				allwinner,pins = "PG8", "PG9";
 				allwinner,function = "uart1";
 				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
 				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 			};
+
+			uart2_pins: uart2 {
+				allwinner,pins = "PA0", "PA1";
+				allwinner,function = "uart2";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
+
+			uart3_pins: uart3 {
+				allwinner,pins = "PG13", "PG14";
+				allwinner,function = "uart3";
+				allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+				allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+			};
 		};
 
 		timer@01c20c00 {
@@ -449,6 +491,45 @@
 			status = "disabled";
 		};
 
+		i2c0: i2c@01c2ac00 {
+			compatible = "allwinner,sun6i-a31-i2c";
+			reg = <0x01c2ac00 0x400>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: i2c@01c2b000 {
+			compatible = "allwinner,sun6i-a31-i2c";
+			reg = <0x01c2b000 0x400>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c1_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2: i2c@01c2b400 {
+			compatible = "allwinner,sun6i-a31-i2c";
+			reg = <0x01c2b000 0x400>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c2_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		gic: interrupt-controller@01c81000 {
 			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
 			reg = <0x01c81000 0x1000>,

arch/arm/boot/dts/sun9i-a80-cubieboard4.dts

@@ -253,6 +253,122 @@
 			reg_rtc_ldo: rtc_ldo {
 				regulator-name = "vcc-rtc-vdd1v8-io";
 			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+
+	axp806: pmic@745 {
+		compatible = "x-powers,axp806";
+		reg = <0x745>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		bldoin-supply = <&reg_dcdce>;
+
+		regulators {
+			reg_s_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "avcc";
+			};
+
+			aldo2 {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's aldo's
+				 */
+				regulator-name = "s_aldo2";
+			};
+
+			aldo3 {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's aldo's
+				 */
+				regulator-name = "s_aldo3";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-name = "vcc18-efuse-adc-display-csi";
+			};
+
+			reg_bldo2: bldo2 {
+				regulator-always-on;
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-name =
+					"vdd18-drampll-vcc18-pll-cpvdd";
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			reg_bldo4: bldo4 {
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-name = "vcc12-hsic";
+			};
+
+			reg_cldo1: cldo1 {
+				/*
+				 * This was 3V in the original design, but
+				 * 3.3V is the recommended supply voltage
+				 * for the Ethernet PHY.
+				 */
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-gmac-phy";
+			};
+
+			reg_cldo2: cldo2 {
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-name = "afvcc-cam";
+			};
+
+			reg_cldo3: cldo3 {
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc-io-wifi-codec-io2";
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpub";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-vpu";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-always-on;
+				regulator-min-microvolt = <2100000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-name = "vcc-bldo-codec-ldoin";
+			};
+
+			sw {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's sw
+				 */
+				regulator-name = "s_sw";
+			};
 		};
 	};
 

arch/arm/boot/dts/sun9i-a80-optimus.dts

@@ -112,7 +112,8 @@
 };
 
 &ehci1 {
-	status = "okay";
+	/* Enable if HSIC peripheral is connected */
+	status = "disabled";
 };
 
 &ehci2 {
@@ -325,6 +326,122 @@
 			reg_rtc_ldo: rtc_ldo {
 				regulator-name = "vcc-rtc-vdd1v8-io";
 			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+
+	axp806: pmic@745 {
+		compatible = "x-powers,axp806";
+		reg = <0x745>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		bldoin-supply = <&reg_dcdce>;
+
+		regulators {
+			reg_s_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "avcc";
+			};
+
+			aldo2 {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's aldo's
+				 */
+				regulator-name = "s_aldo2";
+			};
+
+			aldo3 {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's aldo's
+				 */
+				regulator-name = "s_aldo3";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-name = "vcc18-efuse-adc-display-csi";
+			};
+
+			reg_bldo2: bldo2 {
+				regulator-always-on;
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-name =
+					"vdd18-drampll-vcc18-pll-cpvdd";
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			reg_bldo4: bldo4 {
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-name = "vcc12-hsic";
+			};
+
+			reg_cldo1: cldo1 {
+				/*
+				 * This was 3V in the original design, but
+				 * 3.3V is the recommended supply voltage
+				 * for the Ethernet PHY.
+				 */
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-gmac-phy";
+			};
+
+			reg_cldo2: cldo2 {
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-name = "afvcc-cam";
+			};
+
+			reg_cldo3: cldo3 {
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc-io-wifi-codec-io2";
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpub";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-vpu";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-always-on;
+				regulator-min-microvolt = <2100000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-name = "vcc-bldo-codec-ldoin";
+			};
+
+			sw {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's sw
+				 */
+				regulator-name = "s_sw";
+			};
 		};
 	};
 
@@ -367,7 +484,9 @@
 };
 
 &usbphy2 {
-	status = "okay";
+	phy-supply = <&reg_bldo4>;
+	/* Enable if HSIC peripheral is connected */
+	status = "disabled";
 };
 
 &usbphy3 {