Merge tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/late

Pull "Amlogic 64-bit DT changes for v4.9, round 2" from Kevin Hilman:

Primarily adding support for newly added drivers

- USB host
- I2C
- SPI flash controller
- PWM
- mailbox, MHU
- pinctrl: add pins for SPI, I2C, SDIO

and then enabling these drivers on various boards.

* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
  ARM64: dts: meson-gxbb-p20x: Enable USB Nodes
  ARM64: dts: meson-gxbb: add USB Nodes
  ARM64: dts: gxbb: add i2c bus
  ARM64: dts: meson-gxbb: add I2C nodes
  ARM64: dts: meson-gxbb: add pins for I2C
  ARM64: dts: meson-gxbb: Add SPIFC node
  ARM64: dts: meson-gxbb: add the SDIO pins
  ARM64: dts: amlogic: add spi nor pins
  ARM64: dts: meson-gxbb: use the new GXBB DWMAC glue driver
  ARM64: dts: meson-gxbb: Add Meson GXBB PWM Controller nodes
  ARM64: dts: meson-gxbb: Add Meson MHU Node
  ARM64: dts: amlogic: enable ethernet on all Tronsmart Vega S95 devices

arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts

@@ -92,3 +92,9 @@
 	pinctrl-0 = <&remote_input_ao_pins>;
 	pinctrl-names = "default";
 };
+
+&i2c_A {
+	status = "okay";
+	pinctrl-0 = <&i2c_a_pins>;
+	pinctrl-names = "default";
+};

arch/arm64/boot/dts/amlogic/meson-gxbb-p200.dts

@@ -50,3 +50,9 @@
 	compatible = "amlogic,p200", "amlogic,meson-gxbb";
 	model = "Amlogic Meson GXBB P200 Development Board";
 };
+
+&i2c_B {
+	status = "okay";
+	pinctrl-0 = <&i2c_b_pins>;
+	pinctrl-names = "default";
+};

arch/arm64/boot/dts/amlogic/meson-gxbb-p20x.dtsi

@@ -57,6 +57,19 @@
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x40000000>;
 	};
+
+	usb_pwr: regulator-usb-pwrs {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB_PWR";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		/* signal name in schematic: USB_PWR_EN */
+		gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
 };
 
 /* This UART is brought out to the DB9 connector */
@@ -77,3 +90,20 @@
 	pinctrl-0 = <&remote_input_ao_pins>;
 	pinctrl-names = "default";
 };
+
+&usb0_phy {
+	status = "okay";
+	phy-supply = <&usb_pwr>;
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};

arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95.dtsi

@@ -52,6 +52,19 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	usb_vbus: regulator-usb0-vbus {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB0_VBUS";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&gpio GPIODV_24 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 };
 
 &uart_AO {
@@ -66,3 +79,26 @@
 	pinctrl-0 = <&remote_input_ao_pins>;
 	pinctrl-names = "default";
 };
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0_phy {
+	status = "okay";
+	phy-supply = <&usb_vbus>;
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};

arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi

@@ -151,6 +151,25 @@
 		#size-cells = <2>;
 		ranges;
 
+		usb0_phy: phy@c0000000 {
+			compatible = "amlogic,meson-gxbb-usb2-phy";
+			#phy-cells = <0>;
+			reg = <0x0 0xc0000000 0x0 0x20>;
+			resets = <&reset RESET_USB_OTG>;
+			clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB0>;
+			clock-names = "usb_general", "usb";
+			status = "disabled";
+		};
+
+		usb1_phy: phy@c0000020 {
+			compatible = "amlogic,meson-gxbb-usb2-phy";
+			#phy-cells = <0>;
+			reg = <0x0 0xc0000020 0x0 0x20>;
+			clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB1>;
+			clock-names = "usb_general", "usb";
+			status = "disabled";
+		};
+
 		cbus: cbus@c1100000 {
 			compatible = "simple-bus";
 			reg = <0x0 0xc1100000 0x0 0x100000>;
@@ -180,6 +199,27 @@
 				status = "disabled";
 			};
 
+			pwm_ab: pwm@8550 {
+				compatible = "amlogic,meson-gxbb-pwm";
+				reg = <0x0 0x08550 0x0 0x10>;
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			pwm_cd: pwm@8650 {
+				compatible = "amlogic,meson-gxbb-pwm";
+				reg = <0x0 0x08650 0x0 0x10>;
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			pwm_ef: pwm@86c0 {
+				compatible = "amlogic,meson-gxbb-pwm";
+				reg = <0x0 0x086c0 0x0 0x10>;
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
 			uart_C: serial@8700 {
 				compatible = "amlogic,meson-uart";
 				reg = <0x0 0x8700 0x0 0x14>;
@@ -193,6 +233,45 @@
 				reg = <0x0 0x098d0 0x0 0x10>;
 				clocks = <&xtal>;
 			};
+
+			spifc: spi@8c80 {
+				compatible = "amlogic,meson-gxbb-spifc";
+				reg = <0x0 0x08c80 0x0 0x80>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&clkc CLKID_SPI>;
+				status = "disabled";
+			};
+
+			i2c_A: i2c@8500 {
+				compatible = "amlogic,meson-gxbb-i2c";
+				reg = <0x0 0x08500 0x0 0x20>;
+				interrupts = <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&clkc CLKID_I2C>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c_B: i2c@87c0 {
+				compatible = "amlogic,meson-gxbb-i2c";
+				reg = <0x0 0x087c0 0x0 0x20>;
+				interrupts = <GIC_SPI 214 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&clkc CLKID_I2C>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c_C: i2c@87e0 {
+				compatible = "amlogic,meson-gxbb-i2c";
+				reg = <0x0 0x087e0 0x0 0x20>;
+				interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&clkc CLKID_I2C>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
 		};
 
 		gic: interrupt-controller@c4301000 {
@@ -244,6 +323,14 @@
 					};
 				};
 
+				i2c_ao_pins: i2c_ao {
+					mux {
+						groups = "i2c_sck_ao",
+						       "i2c_sda_ao";
+						function = "i2c_ao";
+					};
+				};
+
 				pwm_ao_a_3_pins: pwm_ao_a_3 {
 					mux {
 						groups = "pwm_ao_a_3";
@@ -294,6 +381,23 @@
 				interrupts = <GIC_SPI 196 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};
+
+			pwm_ab_AO: pwm@550 {
+				compatible = "amlogic,meson-gxbb-pwm";
+				reg = <0x0 0x0550 0x0 0x10>;
+				#pwm-cells = <3>;
+				status = "disabled";
+			};
+
+			i2c_AO: i2c@500 {
+				compatible = "amlogic,meson-gxbb-i2c";
+				reg = <0x0 0x500 0x0 0x20>;
+				interrupts = <GIC_SPI 195 IRQ_TYPE_EDGE_RISING>;
+				clocks = <&clkc CLKID_AO_I2C>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
 		};
 
 		periphs: periphs@c8834000 {
@@ -333,6 +437,16 @@
 					};
 				};
 
+				nor_pins: nor {
+					mux {
+						groups = "nor_d",
+						       "nor_q",
+						       "nor_c",
+						       "nor_cs";
+						function = "nor";
+					};
+				};
+
 				sdcard_pins: sdcard {
 					mux {
 						groups = "sdcard_d0",
@@ -345,6 +459,25 @@
 					};
 				};
 
+				sdio_pins: sdio {
+					mux {
+						groups = "sdio_d0",
+						       "sdio_d1",
+						       "sdio_d2",
+						       "sdio_d3",
+						       "sdio_cmd",
+						       "sdio_clk";
+						function = "sdio";
+					};
+				};
+
+				sdio_irq_pins: sdio_irq {
+					mux {
+						groups = "sdio_irq";
+						function = "sdio";
+					};
+				};
+
 				uart_a_pins: uart_a {
 					mux {
 						groups = "uart_tx_a",
@@ -369,6 +502,30 @@
 					};
 				};
 
+				i2c_a_pins: i2c_a {
+					mux {
+						groups = "i2c_sck_a",
+						       "i2c_sda_a";
+						function = "i2c_a";
+					};
+				};
+
+				i2c_b_pins: i2c_b {
+					mux {
+						groups = "i2c_sck_b",
+						       "i2c_sda_b";
+						function = "i2c_b";
+					};
+				};
+
+				i2c_c_pins: i2c_c {
+					mux {
+						groups = "i2c_sck_c",
+						       "i2c_sda_c";
+						function = "i2c_c";
+					};
+				};
+
 				eth_pins: eth_c {
 					mux {
 						groups = "eth_mdio",
@@ -452,6 +609,15 @@
 				#clock-cells = <1>;
 				reg = <0x0 0x0 0x0 0x3db>;
 			};
+
+			mailbox: mailbox@404 {
+				compatible = "amlogic,meson-gxbb-mhu";
+				reg = <0 0x404 0 0x4c>;
+				interrupts = <0 208 IRQ_TYPE_EDGE_RISING>,
+					     <0 209 IRQ_TYPE_EDGE_RISING>,
+					     <0 210 IRQ_TYPE_EDGE_RISING>;
+				#mbox-cells = <1>;
+			};
 		};
 
 		apb: apb@d0000000 {
@@ -462,14 +628,40 @@
 			ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
 		};
 
+		usb0: usb@c9000000 {
+			compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
+			reg = <0x0 0xc9000000 0x0 0x40000>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clkc CLKID_USB0_DDR_BRIDGE>;
+			clock-names = "otg";
+			phys = <&usb0_phy>;
+			phy-names = "usb2-phy";
+			dr_mode = "host";
+			status = "disabled";
+		};
+
+		usb1: usb@c9100000 {
+			compatible = "amlogic,meson-gxbb-usb", "snps,dwc2";
+			reg = <0x0 0xc9100000 0x0 0x40000>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clkc CLKID_USB1_DDR_BRIDGE>;
+			clock-names = "otg";
+			phys = <&usb1_phy>;
+			phy-names = "usb2-phy";
+			dr_mode = "host";
+			status = "disabled";
+		};
+
 		ethmac: ethernet@c9410000 {
-			compatible = "amlogic,meson6-dwmac", "snps,dwmac";
+			compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac";
 			reg = <0x0 0xc9410000 0x0 0x10000
 			       0x0 0xc8834540 0x0 0x4>;
 			interrupts = <0 8 1>;
 			interrupt-names = "macirq";
-			clocks = <&clkc CLKID_ETH>;
-			clock-names = "stmmaceth";
+			clocks = <&clkc CLKID_ETH>,
+				 <&clkc CLKID_FCLK_DIV2>,
+				 <&clkc CLKID_MPLL2>;
+			clock-names = "stmmaceth", "clkin0", "clkin1";
 			phy-mode = "rgmii";
 			status = "disabled";
 		};