Merge tag 'omap-for-v3.20/cleanup-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup

Merge "omap clean-up for v3.20" from Tony Lindgren:

Clean-up for omaps to remove dead code found with cppcheck after
we've made several SoCs to boot in device tree only mode.

* tag 'omap-for-v3.20/cleanup-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Remove unused ti81xx platform init code
  ARM: OMAP3+: PRM: remove prm_get_reset_sources declaration from headers
  ARM: OMAP2: CM: remove unused PLL functions
  ARM: OMAP2: clock: remove unused apll code
  ARM: OMAP: dma.c: Remove unused function
  ARM: OMAP1: timer32k.c: Remove unused function
  ARM: OMAP1: irq.c: Remove unused function
  ARM: OMAP2+: omap-pm-noop.c: Remove some unused functions
  ARM: OMAP2+: voltage: Remove some unused functions
  ARM: OMAP2+: powerdomain.c: Remove some unused functions
  ARM: OMAP2+: omap_hwmod.c: Remove some unused functions
  ARM: OMAP2+: dpll44xx.c: Remove unused function
  ARM: OMAP2+: cm33xx.c: Remove some unused functions
  ARM: OMAP2+: clkt2xxx_apll.c: Remove some unused functions

Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/mach-omap1/irq.c

@@ -64,11 +64,6 @@ u32 omap_irq_flags;
 static unsigned int irq_bank_count;
 static struct omap_irq_bank *irq_banks;
 
-static inline unsigned int irq_bank_readl(int bank, int offset)
-{
-	return omap_readl(irq_banks[bank].base_reg + offset);
-}
-
 static inline void irq_bank_writel(unsigned long value, int bank, int offset)
 {
 	omap_writel(value, irq_banks[bank].base_reg + offset);

arch/arm/mach-omap1/timer32k.c

@@ -91,11 +91,6 @@ static inline void omap_32k_timer_write(int val, int reg)
 	omap_writew(val, OMAP1_32K_TIMER_BASE + reg);
 }
 
-static inline unsigned long omap_32k_timer_read(int reg)
-{
-	return omap_readl(OMAP1_32K_TIMER_BASE + reg) & 0xffffff;
-}
-
 static inline void omap_32k_timer_start(unsigned long load_val)
 {
 	if (!load_val)

arch/arm/mach-omap2/Makefile

@@ -181,7 +181,6 @@ obj-$(CONFIG_SOC_DRA7XX)		+= clockdomains7xx_data.o
 obj-$(CONFIG_ARCH_OMAP2)		+= $(clock-common) clock2xxx.o
 obj-$(CONFIG_ARCH_OMAP2)		+= clkt2xxx_dpllcore.o
 obj-$(CONFIG_ARCH_OMAP2)		+= clkt2xxx_virt_prcm_set.o
-obj-$(CONFIG_ARCH_OMAP2)		+= clkt2xxx_apll.o
 obj-$(CONFIG_ARCH_OMAP2)		+= clkt2xxx_dpll.o clkt_iclk.o
 obj-$(CONFIG_SOC_OMAP2430)		+= clock2430.o
 obj-$(CONFIG_ARCH_OMAP3)		+= $(clock-common) clock3xxx.o

arch/arm/mach-omap2/cclock3xxx_data.c

@@ -3634,10 +3634,6 @@ int __init omap3xxx_clk_init(void)
 		omap_clocks_register(omap36xx_am35xx_omap3430es2plus_clks,
 				     ARRAY_SIZE(omap36xx_am35xx_omap3430es2plus_clks));
 		omap_clocks_register(omap3xxx_clks, ARRAY_SIZE(omap3xxx_clks));
-	} else if (soc_is_am33xx()) {
-		cpu_mask = RATE_IN_AM33XX;
-	} else if (cpu_is_ti814x()) {
-		cpu_mask = RATE_IN_TI814X;
 	} else if (cpu_is_omap34xx()) {
 		if (omap_rev() == OMAP3430_REV_ES1_0) {
 			cpu_mask = RATE_IN_3430ES1;
@@ -3681,7 +3677,7 @@ int __init omap3xxx_clk_init(void)
 	 * Lock DPLL5 -- here only until other device init code can
 	 * handle this
 	 */
-	if (!cpu_is_ti81xx() && (omap_rev() >= OMAP3430_REV_ES2_0))
+	if (omap_rev() >= OMAP3430_REV_ES2_0)
 		omap3_clk_lock_dpll5();
 
 	/* Avoid sleeping during omap3_core_dpll_m2_set_rate() */

arch/arm/mach-omap2/clkt2xxx_apll.c

@@ -1,142 +0,0 @@
-/*
- * OMAP2xxx APLL clock control functions
- *
- * Copyright (C) 2005-2008 Texas Instruments, Inc.
- * Copyright (C) 2004-2010 Nokia Corporation
- *
- * Contacts:
- * Richard Woodruff <r-woodruff2@ti.com>
- * Paul Walmsley
- *
- * Based on earlier work by Tuukka Tikkanen, Tony Lindgren,
- * Gordon McNutt and RidgeRun, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#undef DEBUG
-
-#include <linux/kernel.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-
-
-#include "clock.h"
-#include "clock2xxx.h"
-#include "cm2xxx.h"
-#include "cm-regbits-24xx.h"
-
-/* CM_CLKEN_PLL.EN_{54,96}M_PLL options (24XX) */
-#define EN_APLL_STOPPED			0
-#define EN_APLL_LOCKED			3
-
-/* CM_CLKSEL1_PLL.APLLS_CLKIN options (24XX) */
-#define APLLS_CLKIN_19_2MHZ		0
-#define APLLS_CLKIN_13MHZ		2
-#define APLLS_CLKIN_12MHZ		3
-
-/* Private functions */
-
-/**
- * omap2xxx_clk_apll_locked - is the APLL locked?
- * @hw: struct clk_hw * of the APLL to check
- *
- * If the APLL IP block referred to by @hw indicates that it's locked,
- * return true; otherwise, return false.
- */
-static bool omap2xxx_clk_apll_locked(struct clk_hw *hw)
-{
-	struct clk_hw_omap *clk = to_clk_hw_omap(hw);
-	u32 r, apll_mask;
-
-	apll_mask = EN_APLL_LOCKED << clk->enable_bit;
-
-	r = omap2xxx_cm_get_pll_status();
-
-	return ((r & apll_mask) == apll_mask) ? true : false;
-}
-
-int omap2_clk_apll96_enable(struct clk_hw *hw)
-{
-	return omap2xxx_cm_apll96_enable();
-}
-
-int omap2_clk_apll54_enable(struct clk_hw *hw)
-{
-	return omap2xxx_cm_apll54_enable();
-}
-
-static void _apll96_allow_idle(struct clk_hw_omap *clk)
-{
-	omap2xxx_cm_set_apll96_auto_low_power_stop();
-}
-
-static void _apll96_deny_idle(struct clk_hw_omap *clk)
-{
-	omap2xxx_cm_set_apll96_disable_autoidle();
-}
-
-static void _apll54_allow_idle(struct clk_hw_omap *clk)
-{
-	omap2xxx_cm_set_apll54_auto_low_power_stop();
-}
-
-static void _apll54_deny_idle(struct clk_hw_omap *clk)
-{
-	omap2xxx_cm_set_apll54_disable_autoidle();
-}
-
-void omap2_clk_apll96_disable(struct clk_hw *hw)
-{
-	omap2xxx_cm_apll96_disable();
-}
-
-void omap2_clk_apll54_disable(struct clk_hw *hw)
-{
-	omap2xxx_cm_apll54_disable();
-}
-
-unsigned long omap2_clk_apll54_recalc(struct clk_hw *hw,
-				      unsigned long parent_rate)
-{
-	return (omap2xxx_clk_apll_locked(hw)) ? 54000000 : 0;
-}
-
-unsigned long omap2_clk_apll96_recalc(struct clk_hw *hw,
-				      unsigned long parent_rate)
-{
-	return (omap2xxx_clk_apll_locked(hw)) ? 96000000 : 0;
-}
-
-/* Public data */
-const struct clk_hw_omap_ops clkhwops_apll54 = {
-	.allow_idle	= _apll54_allow_idle,
-	.deny_idle	= _apll54_deny_idle,
-};
-
-const struct clk_hw_omap_ops clkhwops_apll96 = {
-	.allow_idle	= _apll96_allow_idle,
-	.deny_idle	= _apll96_deny_idle,
-};
-
-/* Public functions */
-
-u32 omap2xxx_get_apll_clkin(void)
-{
-	u32 aplls, srate = 0;
-
-	aplls = omap2xxx_cm_get_pll_config();
-	aplls &= OMAP24XX_APLLS_CLKIN_MASK;
-	aplls >>= OMAP24XX_APLLS_CLKIN_SHIFT;
-
-	if (aplls == APLLS_CLKIN_19_2MHZ)
-		srate = 19200000;
-	else if (aplls == APLLS_CLKIN_13MHZ)
-		srate = 13000000;
-	else if (aplls == APLLS_CLKIN_12MHZ)
-		srate = 12000000;
-
-	return srate;
-}
-

arch/arm/mach-omap2/clock.h

@@ -177,7 +177,6 @@ struct clksel {
 u32 omap3_dpll_autoidle_read(struct clk_hw_omap *clk);
 void omap3_dpll_allow_idle(struct clk_hw_omap *clk);
 void omap3_dpll_deny_idle(struct clk_hw_omap *clk);
-int omap4_dpllmx_gatectrl_read(struct clk_hw_omap *clk);
 void omap4_dpllmx_allow_gatectrl(struct clk_hw_omap *clk);
 void omap4_dpllmx_deny_gatectrl(struct clk_hw_omap *clk);
 

arch/arm/mach-omap2/clock2xxx.h

@@ -22,12 +22,7 @@ unsigned long omap2xxx_sys_clk_recalc(struct clk_hw *clk,
 unsigned long omap2_osc_clk_recalc(struct clk_hw *clk,
 				   unsigned long parent_rate);
 void omap2xxx_clkt_dpllcore_init(struct clk_hw *hw);
-unsigned long omap2_clk_apll54_recalc(struct clk_hw *hw,
-				      unsigned long parent_rate);
-unsigned long omap2_clk_apll96_recalc(struct clk_hw *hw,
-				      unsigned long parent_rate);
 unsigned long omap2xxx_clk_get_core_rate(void);
-u32 omap2xxx_get_apll_clkin(void);
 u32 omap2xxx_get_sysclkdiv(void);
 void omap2xxx_clk_prepare_for_reboot(void);
 void omap2xxx_clkt_vps_check_bootloader_rates(void);
@@ -46,11 +41,5 @@ int omap2430_clk_init(void);
 #endif
 
 extern struct clk_hw *dclk_hw;
-int omap2_enable_osc_ck(struct clk_hw *hw);
-void omap2_disable_osc_ck(struct clk_hw *hw);
-int omap2_clk_apll96_enable(struct clk_hw *hw);
-int omap2_clk_apll54_enable(struct clk_hw *hw);
-void omap2_clk_apll96_disable(struct clk_hw *hw);
-void omap2_clk_apll54_disable(struct clk_hw *hw);
 
 #endif

arch/arm/mach-omap2/cm2xxx.c

@@ -370,16 +370,6 @@ u32 omap2xxx_cm_get_core_pll_config(void)
 	return omap2_cm_read_mod_reg(PLL_MOD, CM_CLKSEL2);
 }
 
-u32 omap2xxx_cm_get_pll_config(void)
-{
-	return omap2_cm_read_mod_reg(PLL_MOD, CM_CLKSEL1);
-}
-
-u32 omap2xxx_cm_get_pll_status(void)
-{
-	return omap2_cm_read_mod_reg(PLL_MOD, CM_CLKEN);
-}
-
 void omap2xxx_cm_set_mod_dividers(u32 mpu, u32 dsp, u32 gfx, u32 core, u32 mdm)
 {
 	u32 tmp;

arch/arm/mach-omap2/cm2xxx.h

@@ -60,8 +60,6 @@ extern int omap2xxx_cm_fclks_active(void);
 extern int omap2xxx_cm_mpu_retention_allowed(void);
 extern u32 omap2xxx_cm_get_core_clk_src(void);
 extern u32 omap2xxx_cm_get_core_pll_config(void);
-extern u32 omap2xxx_cm_get_pll_config(void);
-extern u32 omap2xxx_cm_get_pll_status(void);
 extern void omap2xxx_cm_set_mod_dividers(u32 mpu, u32 dsp, u32 gfx, u32 core,
 					 u32 mdm);
 

arch/arm/mach-omap2/cm33xx.c

@@ -72,27 +72,6 @@ static inline u32 am33xx_cm_rmw_reg_bits(u32 mask, u32 bits, s16 inst, s16 idx)
 	return v;
 }
 
-static inline u32 am33xx_cm_set_reg_bits(u32 bits, s16 inst, s16 idx)
-{
-	return am33xx_cm_rmw_reg_bits(bits, bits, inst, idx);
-}
-
-static inline u32 am33xx_cm_clear_reg_bits(u32 bits, s16 inst, s16 idx)
-{
-	return am33xx_cm_rmw_reg_bits(bits, 0x0, inst, idx);
-}
-
-static inline u32 am33xx_cm_read_reg_bits(u16 inst, s16 idx, u32 mask)
-{
-	u32 v;
-
-	v = am33xx_cm_read_reg(inst, idx);
-	v &= mask;
-	v >>= __ffs(mask);
-
-	return v;
-}
-
 /**
  * _clkctrl_idlest - read a CM_*_CLKCTRL register; mask & shift IDLEST bitfield
  * @inst: CM instance register offset (*_INST macro)

arch/arm/mach-omap2/dpll44xx.c

@@ -36,26 +36,6 @@
 /* Static rate multiplier for OMAP4 REGM4XEN clocks */
 #define OMAP4430_REGM4XEN_MULT				4
 
-/* Supported only on OMAP4 */
-int omap4_dpllmx_gatectrl_read(struct clk_hw_omap *clk)
-{
-	u32 v;
-	u32 mask;
-
-	if (!clk || !clk->clksel_reg)
-		return -EINVAL;
-
-	mask = clk->flags & CLOCK_CLKOUTX2 ?
-			OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK :
-			OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK;
-
-	v = omap2_clk_readl(clk, clk->clksel_reg);
-	v &= mask;
-	v >>= __ffs(mask);
-
-	return v;
-}
-
 void omap4_dpllmx_allow_gatectrl(struct clk_hw_omap *clk)
 {
 	u32 v;

arch/arm/mach-omap2/omap-pm-noop.c

@@ -86,200 +86,10 @@ int omap_pm_set_min_bus_tput(struct device *dev, u8 agent_id, unsigned long r)
 	return 0;
 }
 
-int omap_pm_set_max_dev_wakeup_lat(struct device *req_dev, struct device *dev,
-				   long t)
-{
-	if (!req_dev || !dev || t < -1) {
-		WARN(1, "OMAP PM: %s: invalid parameter(s)", __func__);
-		return -EINVAL;
-	}
-
-	if (t == -1)
-		pr_debug("OMAP PM: remove max device latency constraint: dev %s\n",
-			 dev_name(dev));
-	else
-		pr_debug("OMAP PM: add max device latency constraint: dev %s, t = %ld usec\n",
-			 dev_name(dev), t);
-
-	/*
-	 * For current Linux, this needs to map the device to a
-	 * powerdomain, then go through the list of current max lat
-	 * constraints on that powerdomain and find the smallest.  If
-	 * the latency constraint has changed, the code should
-	 * recompute the state to enter for the next powerdomain
-	 * state.  Conceivably, this code should also determine
-	 * whether to actually disable the device clocks or not,
-	 * depending on how long it takes to re-enable the clocks.
-	 *
-	 * TI CDP code can call constraint_set here.
-	 */
-
-	return 0;
-}
-
-int omap_pm_set_max_sdma_lat(struct device *dev, long t)
-{
-	if (!dev || t < -1) {
-		WARN(1, "OMAP PM: %s: invalid parameter(s)", __func__);
-		return -EINVAL;
-	}
-
-	if (t == -1)
-		pr_debug("OMAP PM: remove max DMA latency constraint: dev %s\n",
-			 dev_name(dev));
-	else
-		pr_debug("OMAP PM: add max DMA latency constraint: dev %s, t = %ld usec\n",
-			 dev_name(dev), t);
-
-	/*
-	 * For current Linux PM QOS params, this code should scan the
-	 * list of maximum CPU and DMA latencies and select the
-	 * smallest, then set cpu_dma_latency pm_qos_param
-	 * accordingly.
-	 *
-	 * For future Linux PM QOS params, with separate CPU and DMA
-	 * latency params, this code should just set the dma_latency param.
-	 *
-	 * TI CDP code can call constraint_set here.
-	 */
-
-	return 0;
-}
-
-int omap_pm_set_min_clk_rate(struct device *dev, struct clk *c, long r)
-{
-	if (!dev || !c || r < 0) {
-		WARN(1, "OMAP PM: %s: invalid parameter(s)", __func__);
-		return -EINVAL;
-	}
-
-	if (r == 0)
-		pr_debug("OMAP PM: remove min clk rate constraint: dev %s\n",
-			 dev_name(dev));
-	else
-		pr_debug("OMAP PM: add min clk rate constraint: dev %s, rate = %ld Hz\n",
-			 dev_name(dev), r);
-
-	/*
-	 * Code in a real implementation should keep track of these
-	 * constraints on the clock, and determine the highest minimum
-	 * clock rate.  It should iterate over each OPP and determine
-	 * whether the OPP will result in a clock rate that would
-	 * satisfy this constraint (and any other PM constraint in effect
-	 * at that time).  Once it finds the lowest-voltage OPP that
-	 * meets those conditions, it should switch to it, or return
-	 * an error if the code is not capable of doing so.
-	 */
-
-	return 0;
-}
-
 /*
  * DSP Bridge-specific constraints
  */
 
-const struct omap_opp *omap_pm_dsp_get_opp_table(void)
-{
-	pr_debug("OMAP PM: DSP request for OPP table\n");
-
-	/*
-	 * Return DSP frequency table here:  The final item in the
-	 * array should have .rate = .opp_id = 0.
-	 */
-
-	return NULL;
-}
-
-void omap_pm_dsp_set_min_opp(u8 opp_id)
-{
-	if (opp_id == 0) {
-		WARN_ON(1);
-		return;
-	}
-
-	pr_debug("OMAP PM: DSP requests minimum VDD1 OPP to be %d\n", opp_id);
-
-	/*
-	 *
-	 * For l-o dev tree, our VDD1 clk is keyed on OPP ID, so we
-	 * can just test to see which is higher, the CPU's desired OPP
-	 * ID or the DSP's desired OPP ID, and use whichever is
-	 * highest.
-	 *
-	 * In CDP12.14+, the VDD1 OPP custom clock that controls the DSP
-	 * rate is keyed on MPU speed, not the OPP ID.  So we need to
-	 * map the OPP ID to the MPU speed for use with clk_set_rate()
-	 * if it is higher than the current OPP clock rate.
-	 *
-	 */
-}
-
-
-u8 omap_pm_dsp_get_opp(void)
-{
-	pr_debug("OMAP PM: DSP requests current DSP OPP ID\n");
-
-	/*
-	 * For l-o dev tree, call clk_get_rate() on VDD1 OPP clock
-	 *
-	 * CDP12.14+:
-	 * Call clk_get_rate() on the OPP custom clock, map that to an
-	 * OPP ID using the tables defined in board-*.c/chip-*.c files.
-	 */
-
-	return 0;
-}
-
-/*
- * CPUFreq-originated constraint
- *
- * In the future, this should be handled by custom OPP clocktype
- * functions.
- */
-
-struct cpufreq_frequency_table **omap_pm_cpu_get_freq_table(void)
-{
-	pr_debug("OMAP PM: CPUFreq request for frequency table\n");
-
-	/*
-	 * Return CPUFreq frequency table here: loop over
-	 * all VDD1 clkrates, pull out the mpu_ck frequencies, build
-	 * table
-	 */
-
-	return NULL;
-}
-
-void omap_pm_cpu_set_freq(unsigned long f)
-{
-	if (f == 0) {
-		WARN_ON(1);
-		return;
-	}
-
-	pr_debug("OMAP PM: CPUFreq requests CPU frequency to be set to %lu\n",
-		 f);
-
-	/*
-	 * For l-o dev tree, determine whether MPU freq or DSP OPP id
-	 * freq is higher.  Find the OPP ID corresponding to the
-	 * higher frequency.  Call clk_round_rate() and clk_set_rate()
-	 * on the OPP custom clock.
-	 *
-	 * CDP should just be able to set the VDD1 OPP clock rate here.
-	 */
-}
-
-unsigned long omap_pm_cpu_get_freq(void)
-{
-	pr_debug("OMAP PM: CPUFreq requests current CPU frequency\n");
-
-	/*
-	 * Call clk_get_rate() on the mpu_ck.
-	 */
-
-	return 0;
-}
 
 /**
  * omap_pm_enable_off_mode - notify OMAP PM that off-mode is enabled
@@ -363,9 +173,3 @@ int __init omap_pm_if_init(void)
 {
 	return 0;
 }
-
-void omap_pm_if_exit(void)
-{
-	/* Deallocate CPUFreq frequency table here */
-}
-

arch/arm/mach-omap2/omap-pm.h

@@ -50,14 +50,6 @@ int __init omap_pm_if_early_init(void);
  */
 int __init omap_pm_if_init(void);
 
-/**
- * omap_pm_if_exit - OMAP PM exit code
- *
- * Exit code; currently unused.  The "_if_" is to avoid name
- * collisions with the PM idle-loop code.
- */
-void omap_pm_if_exit(void);
-
 /*
  * Device-driver-originated constraints (via board-*.c files, platform_data)
  */
@@ -132,163 +124,6 @@ int omap_pm_set_max_mpu_wakeup_lat(struct device *dev, long t);
 int omap_pm_set_min_bus_tput(struct device *dev, u8 agent_id, unsigned long r);
 
 
-/**
- * omap_pm_set_max_dev_wakeup_lat - set the maximum device enable latency
- * @req_dev: struct device * requesting the constraint, or NULL if none
- * @dev: struct device * to set the constraint one
- * @t: maximum device wakeup latency in microseconds
- *
- * Request that the maximum amount of time necessary for a device @dev
- * to become accessible after its clocks are enabled should be no
- * greater than @t microseconds.  Specifically, this represents the
- * time from when a device driver enables device clocks with
- * clk_enable(), to when the register reads and writes on the device
- * will succeed.  This function should be called before clk_disable()
- * is called, since the power state transition decision may be made
- * during clk_disable().
- *
- * It is intended that underlying PM code will use this information to
- * determine what power state to put the powerdomain enclosing this
- * device into.
- *
- * Multiple calls to omap_pm_set_max_dev_wakeup_lat() will replace the
- * previous wakeup latency values for this device.  To remove the
- * wakeup latency restriction for this device, call with t = -1.
- *
- * Returns -EINVAL for an invalid argument, -ERANGE if the constraint
- * is not satisfiable, or 0 upon success.
- */
-int omap_pm_set_max_dev_wakeup_lat(struct device *req_dev, struct device *dev,
-				   long t);
-
-
-/**
- * omap_pm_set_max_sdma_lat - set the maximum system DMA transfer start latency
- * @dev: struct device *
- * @t: maximum DMA transfer start latency in microseconds
- *
- * Request that the maximum system DMA transfer start latency for this
- * device 'dev' should be no greater than 't' microseconds.  "DMA
- * transfer start latency" here is defined as the elapsed time from
- * when a device (e.g., McBSP) requests that a system DMA transfer
- * start or continue, to the time at which data starts to flow into
- * that device from the system DMA controller.
- *
- * It is intended that underlying PM code will use this information to
- * determine what power state to put the CORE powerdomain into.
- *
- * Since system DMA transfers may not involve the MPU, this function
- * will not affect MPU wakeup latency.  Use set_max_cpu_lat() to do
- * so.  Similarly, this function will not affect device wakeup latency
- * -- use set_max_dev_wakeup_lat() to affect that.
- *
- * Multiple calls to set_max_sdma_lat() will replace the previous t
- * value for this device.  To remove the maximum DMA latency for this
- * device, call with t = -1.
- *
- * Returns -EINVAL for an invalid argument, -ERANGE if the constraint
- * is not satisfiable, or 0 upon success.
- */
-int omap_pm_set_max_sdma_lat(struct device *dev, long t);
-
-
-/**
- * omap_pm_set_min_clk_rate - set minimum clock rate requested by @dev
- * @dev: struct device * requesting the constraint
- * @clk: struct clk * to set the minimum rate constraint on
- * @r: minimum rate in Hz
- *
- * Request that the minimum clock rate on the device @dev's clk @clk
- * be no less than @r Hz.
- *
- * It is expected that the OMAP PM code will use this information to
- * find an OPP or clock setting that will satisfy this clock rate
- * constraint, along with any other applicable system constraints on
- * the clock rate or corresponding voltage, etc.
- *
- * omap_pm_set_min_clk_rate() differs from the clock code's
- * clk_set_rate() in that it considers other constraints before taking
- * any hardware action, and may change a system OPP rather than just a
- * clock rate.  clk_set_rate() is intended to be a low-level
- * interface.
- *
- * omap_pm_set_min_clk_rate() is easily open to abuse.  A better API
- * would be something like "omap_pm_set_min_dev_performance()";
- * however, there is no easily-generalizable concept of performance
- * that applies to all devices.  Only a device (and possibly the
- * device subsystem) has both the subsystem-specific knowledge, and
- * the hardware IP block-specific knowledge, to translate a constraint
- * on "touchscreen sampling accuracy" or "number of pixels or polygons
- * rendered per second" to a clock rate.  This translation can be
- * dependent on the hardware IP block's revision, or firmware version,
- * and the driver is the only code on the system that has this
- * information and can know how to translate that into a clock rate.
- *
- * The intended use-case for this function is for userspace or other
- * kernel code to communicate a particular performance requirement to
- * a subsystem; then for the subsystem to communicate that requirement
- * to something that is meaningful to the device driver; then for the
- * device driver to convert that requirement to a clock rate, and to
- * then call omap_pm_set_min_clk_rate().
- *
- * Users of this function (such as device drivers) should not simply
- * call this function with some high clock rate to ensure "high
- * performance."  Rather, the device driver should take a performance
- * constraint from its subsystem, such as "render at least X polygons
- * per second," and use some formula or table to convert that into a
- * clock rate constraint given the hardware type and hardware
- * revision.  Device drivers or subsystems should not assume that they
- * know how to make a power/performance tradeoff - some device use
- * cases may tolerate a lower-fidelity device function for lower power
- * consumption; others may demand a higher-fidelity device function,
- * no matter what the power consumption.
- *
- * Multiple calls to omap_pm_set_min_clk_rate() will replace the
- * previous rate value for the device @dev.  To remove the minimum clock
- * rate constraint for the device, call with r = 0.
- *
- * Returns -EINVAL for an invalid argument, -ERANGE if the constraint
- * is not satisfiable, or 0 upon success.
- */
-int omap_pm_set_min_clk_rate(struct device *dev, struct clk *c, long r);
-
-/*
- * DSP Bridge-specific constraints
- */
-
-/**
- * omap_pm_dsp_get_opp_table - get OPP->DSP clock frequency table
- *
- * Intended for use by DSPBridge.  Returns an array of OPP->DSP clock
- * frequency entries.  The final item in the array should have .rate =
- * .opp_id = 0.
- */
-const struct omap_opp *omap_pm_dsp_get_opp_table(void);
-
-/**
- * omap_pm_dsp_set_min_opp - receive desired OPP target ID from DSP Bridge
- * @opp_id: target DSP OPP ID
- *
- * Set a minimum OPP ID for the DSP.  This is intended to be called
- * only from the DSP Bridge MPU-side driver.  Unfortunately, the only
- * information that code receives from the DSP/BIOS load estimator is the
- * target OPP ID; hence, this interface.  No return value.
- */
-void omap_pm_dsp_set_min_opp(u8 opp_id);
-
-/**
- * omap_pm_dsp_get_opp - report the current DSP OPP ID
- *
- * Report the current OPP for the DSP.  Since on OMAP3, the DSP and
- * MPU share a single voltage domain, the OPP ID returned back may
- * represent a higher DSP speed than the OPP requested via
- * omap_pm_dsp_set_min_opp().
- *
- * Returns the current VDD1 OPP ID, or 0 upon error.
- */
-u8 omap_pm_dsp_get_opp(void);
-
-
 /*
  * CPUFreq-originated constraint
  *
@@ -296,33 +131,6 @@ u8 omap_pm_dsp_get_opp(void);
  * functions.
  */
 
-/**
- * omap_pm_cpu_get_freq_table - return a cpufreq_frequency_table array ptr
- *
- * Provide a frequency table usable by CPUFreq for the current chip/board.
- * Returns a pointer to a struct cpufreq_frequency_table array or NULL
- * upon error.
- */
-struct cpufreq_frequency_table **omap_pm_cpu_get_freq_table(void);
-
-/**
- * omap_pm_cpu_set_freq - set the current minimum MPU frequency
- * @f: MPU frequency in Hz
- *
- * Set the current minimum CPU frequency.  The actual CPU frequency
- * used could end up higher if the DSP requested a higher OPP.
- * Intended to be called by plat-omap/cpu_omap.c:omap_target().  No
- * return value.
- */
-void omap_pm_cpu_set_freq(unsigned long f);
-
-/**
- * omap_pm_cpu_get_freq - report the current CPU frequency
- *
- * Returns the current MPU frequency, or 0 upon error.
- */
-unsigned long omap_pm_cpu_get_freq(void);
-
 
 /*
  * Device context loss tracking

arch/arm/mach-omap2/omap_hwmod.c

@@ -3384,91 +3384,6 @@ int omap_hwmod_shutdown(struct omap_hwmod *oh)
 	return 0;
 }
 
-/**
- * omap_hwmod_enable_clocks - enable main_clk, all interface clocks
- * @oh: struct omap_hwmod *oh
- *
- * Intended to be called by the omap_device code.
- */
-int omap_hwmod_enable_clocks(struct omap_hwmod *oh)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&oh->_lock, flags);
-	_enable_clocks(oh);
-	spin_unlock_irqrestore(&oh->_lock, flags);
-
-	return 0;
-}
-
-/**
- * omap_hwmod_disable_clocks - disable main_clk, all interface clocks
- * @oh: struct omap_hwmod *oh
- *
- * Intended to be called by the omap_device code.
- */
-int omap_hwmod_disable_clocks(struct omap_hwmod *oh)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&oh->_lock, flags);
-	_disable_clocks(oh);
-	spin_unlock_irqrestore(&oh->_lock, flags);
-
-	return 0;
-}
-
-/**
- * omap_hwmod_ocp_barrier - wait for posted writes against the hwmod to complete
- * @oh: struct omap_hwmod *oh
- *
- * Intended to be called by drivers and core code when all posted
- * writes to a device must complete before continuing further
- * execution (for example, after clearing some device IRQSTATUS
- * register bits)
- *
- * XXX what about targets with multiple OCP threads?
- */
-void omap_hwmod_ocp_barrier(struct omap_hwmod *oh)
-{
-	BUG_ON(!oh);
-
-	if (!oh->class->sysc || !oh->class->sysc->sysc_flags) {
-		WARN(1, "omap_device: %s: OCP barrier impossible due to device configuration\n",
-			oh->name);
-		return;
-	}
-
-	/*
-	 * Forces posted writes to complete on the OCP thread handling
-	 * register writes
-	 */
-	omap_hwmod_read(oh, oh->class->sysc->sysc_offs);
-}
-
-/**
- * omap_hwmod_reset - reset the hwmod
- * @oh: struct omap_hwmod *
- *
- * Under some conditions, a driver may wish to reset the entire device.
- * Called from omap_device code.  Returns -EINVAL on error or passes along
- * the return value from _reset().
- */
-int omap_hwmod_reset(struct omap_hwmod *oh)
-{
-	int r;
-	unsigned long flags;
-
-	if (!oh)
-		return -EINVAL;
-
-	spin_lock_irqsave(&oh->_lock, flags);
-	r = _reset(oh);
-	spin_unlock_irqrestore(&oh->_lock, flags);
-
-	return r;
-}
-
 /*
  * IP block data retrieval functions
  */
@@ -3723,51 +3638,11 @@ void __iomem *omap_hwmod_get_mpu_rt_va(struct omap_hwmod *oh)
 	return oh->_mpu_rt_va;
 }
 
-/**
- * omap_hwmod_add_initiator_dep - add sleepdep from @init_oh to @oh
- * @oh: struct omap_hwmod *
- * @init_oh: struct omap_hwmod * (initiator)
- *
- * Add a sleep dependency between the initiator @init_oh and @oh.
- * Intended to be called by DSP/Bridge code via platform_data for the
- * DSP case; and by the DMA code in the sDMA case.  DMA code, *Bridge
- * code needs to add/del initiator dependencies dynamically
- * before/after accessing a device.  Returns the return value from
- * _add_initiator_dep().
- *
- * XXX Keep a usecount in the clockdomain code
- */
-int omap_hwmod_add_initiator_dep(struct omap_hwmod *oh,
-				 struct omap_hwmod *init_oh)
-{
-	return _add_initiator_dep(oh, init_oh);
-}
-
 /*
  * XXX what about functions for drivers to save/restore ocp_sysconfig
  * for context save/restore operations?
  */
 
-/**
- * omap_hwmod_del_initiator_dep - remove sleepdep from @init_oh to @oh
- * @oh: struct omap_hwmod *
- * @init_oh: struct omap_hwmod * (initiator)
- *
- * Remove a sleep dependency between the initiator @init_oh and @oh.
- * Intended to be called by DSP/Bridge code via platform_data for the
- * DSP case; and by the DMA code in the sDMA case.  DMA code, *Bridge
- * code needs to add/del initiator dependencies dynamically
- * before/after accessing a device.  Returns the return value from
- * _del_initiator_dep().
- *
- * XXX Keep a usecount in the clockdomain code
- */
-int omap_hwmod_del_initiator_dep(struct omap_hwmod *oh,
-				 struct omap_hwmod *init_oh)
-{
-	return _del_initiator_dep(oh, init_oh);
-}
-
 /**
  * omap_hwmod_enable_wakeup - allow device to wake up the system
  * @oh: struct omap_hwmod *
@@ -3888,33 +3763,6 @@ int omap_hwmod_deassert_hardreset(struct omap_hwmod *oh, const char *name)
 	return ret;
 }
 
-/**
- * omap_hwmod_read_hardreset - read the HW reset line state of submodules
- * contained in the hwmod module
- * @oh: struct omap_hwmod *
- * @name: name of the reset line to look up and read
- *
- * Return the current state of the hwmod @oh's reset line named @name:
- * returns -EINVAL upon parameter error or if this operation
- * is unsupported on the current OMAP; otherwise, passes along the return
- * value from _read_hardreset().
- */
-int omap_hwmod_read_hardreset(struct omap_hwmod *oh, const char *name)
-{
-	int ret;
-	unsigned long flags;
-
-	if (!oh)
-		return -EINVAL;
-
-	spin_lock_irqsave(&oh->_lock, flags);
-	ret = _read_hardreset(oh, name);
-	spin_unlock_irqrestore(&oh->_lock, flags);
-
-	return ret;
-}
-
-
 /**
  * omap_hwmod_for_each_by_class - call @fn for each hwmod of class @classname
  * @classname: struct omap_hwmod_class name to search for
@@ -4024,86 +3872,6 @@ int omap_hwmod_get_context_loss_count(struct omap_hwmod *oh)
 	return ret;
 }
 
-/**
- * omap_hwmod_no_setup_reset - prevent a hwmod from being reset upon setup
- * @oh: struct omap_hwmod *
- *
- * Prevent the hwmod @oh from being reset during the setup process.
- * Intended for use by board-*.c files on boards with devices that
- * cannot tolerate being reset.  Must be called before the hwmod has
- * been set up.  Returns 0 upon success or negative error code upon
- * failure.
- */
-int omap_hwmod_no_setup_reset(struct omap_hwmod *oh)
-{
-	if (!oh)
-		return -EINVAL;
-
-	if (oh->_state != _HWMOD_STATE_REGISTERED) {
-		pr_err("omap_hwmod: %s: cannot prevent setup reset; in wrong state\n",
-			oh->name);
-		return -EINVAL;
-	}
-
-	oh->flags |= HWMOD_INIT_NO_RESET;
-
-	return 0;
-}
-
-/**
- * omap_hwmod_pad_route_irq - route an I/O pad wakeup to a particular MPU IRQ
- * @oh: struct omap_hwmod * containing hwmod mux entries
- * @pad_idx: array index in oh->mux of the hwmod mux entry to route wakeup
- * @irq_idx: the hwmod mpu_irqs array index of the IRQ to trigger on wakeup
- *
- * When an I/O pad wakeup arrives for the dynamic or wakeup hwmod mux
- * entry number @pad_idx for the hwmod @oh, trigger the interrupt
- * service routine for the hwmod's mpu_irqs array index @irq_idx.  If
- * this function is not called for a given pad_idx, then the ISR
- * associated with @oh's first MPU IRQ will be triggered when an I/O
- * pad wakeup occurs on that pad.  Note that @pad_idx is the index of
- * the _dynamic or wakeup_ entry: if there are other entries not
- * marked with OMAP_DEVICE_PAD_WAKEUP or OMAP_DEVICE_PAD_REMUX, these
- * entries are NOT COUNTED in the dynamic pad index.  This function
- * must be called separately for each pad that requires its interrupt
- * to be re-routed this way.  Returns -EINVAL if there is an argument
- * problem or if @oh does not have hwmod mux entries or MPU IRQs;
- * returns -ENOMEM if memory cannot be allocated; or 0 upon success.
- *
- * XXX This function interface is fragile.  Rather than using array
- * indexes, which are subject to unpredictable change, it should be
- * using hwmod IRQ names, and some other stable key for the hwmod mux
- * pad records.
- */
-int omap_hwmod_pad_route_irq(struct omap_hwmod *oh, int pad_idx, int irq_idx)
-{
-	int nr_irqs;
-
-	might_sleep();
-
-	if (!oh || !oh->mux || !oh->mpu_irqs || pad_idx < 0 ||
-	    pad_idx >= oh->mux->nr_pads_dynamic)
-		return -EINVAL;
-
-	/* Check the number of available mpu_irqs */
-	for (nr_irqs = 0; oh->mpu_irqs[nr_irqs].irq >= 0; nr_irqs++)
-		;
-
-	if (irq_idx >= nr_irqs)
-		return -EINVAL;
-
-	if (!oh->mux->irqs) {
-		/* XXX What frees this? */
-		oh->mux->irqs = kzalloc(sizeof(int) * oh->mux->nr_pads_dynamic,
-			GFP_KERNEL);
-		if (!oh->mux->irqs)
-			return -ENOMEM;
-	}
-	oh->mux->irqs[pad_idx] = irq_idx;
-
-	return 0;
-}
-
 /**
  * omap_hwmod_init - initialize the hwmod code
  *

arch/arm/mach-omap2/omap_hwmod.h

@@ -702,13 +702,6 @@ int omap_hwmod_shutdown(struct omap_hwmod *oh);
 
 int omap_hwmod_assert_hardreset(struct omap_hwmod *oh, const char *name);
 int omap_hwmod_deassert_hardreset(struct omap_hwmod *oh, const char *name);
-int omap_hwmod_read_hardreset(struct omap_hwmod *oh, const char *name);
-
-int omap_hwmod_enable_clocks(struct omap_hwmod *oh);
-int omap_hwmod_disable_clocks(struct omap_hwmod *oh);
-
-int omap_hwmod_reset(struct omap_hwmod *oh);
-void omap_hwmod_ocp_barrier(struct omap_hwmod *oh);
 
 void omap_hwmod_write(u32 v, struct omap_hwmod *oh, u16 reg_offs);
 u32 omap_hwmod_read(struct omap_hwmod *oh, u16 reg_offs);
@@ -723,11 +716,6 @@ int omap_hwmod_get_resource_byname(struct omap_hwmod *oh, unsigned int type,
 struct powerdomain *omap_hwmod_get_pwrdm(struct omap_hwmod *oh);
 void __iomem *omap_hwmod_get_mpu_rt_va(struct omap_hwmod *oh);
 
-int omap_hwmod_add_initiator_dep(struct omap_hwmod *oh,
-				 struct omap_hwmod *init_oh);
-int omap_hwmod_del_initiator_dep(struct omap_hwmod *oh,
-				 struct omap_hwmod *init_oh);
-
 int omap_hwmod_enable_wakeup(struct omap_hwmod *oh);
 int omap_hwmod_disable_wakeup(struct omap_hwmod *oh);
 
@@ -739,10 +727,6 @@ int omap_hwmod_for_each_by_class(const char *classname,
 int omap_hwmod_set_postsetup_state(struct omap_hwmod *oh, u8 state);
 int omap_hwmod_get_context_loss_count(struct omap_hwmod *oh);
 
-int omap_hwmod_no_setup_reset(struct omap_hwmod *oh);
-
-int omap_hwmod_pad_route_irq(struct omap_hwmod *oh, int pad_idx, int irq_idx);
-
 extern void __init omap_hwmod_init(void);
 
 const char *omap_hwmod_get_main_clk(struct omap_hwmod *oh);

arch/arm/mach-omap2/omap_phy_internal.c

@@ -152,38 +152,3 @@ void am35x_set_mode(u8 musb_mode)
 
 	omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
 }
-
-void ti81xx_musb_phy_power(u8 on)
-{
-	void __iomem *scm_base = NULL;
-	u32 usbphycfg;
-
-	scm_base = ioremap(TI81XX_SCM_BASE, SZ_2K);
-	if (!scm_base) {
-		pr_err("system control module ioremap failed\n");
-		return;
-	}
-
-	usbphycfg = readl_relaxed(scm_base + USBCTRL0);
-
-	if (on) {
-		if (cpu_is_ti816x()) {
-			usbphycfg |= TI816X_USBPHY0_NORMAL_MODE;
-			usbphycfg &= ~TI816X_USBPHY_REFCLK_OSC;
-		} else if (cpu_is_ti814x()) {
-			usbphycfg &= ~(USBPHY_CM_PWRDN | USBPHY_OTG_PWRDN
-				| USBPHY_DPINPUT | USBPHY_DMINPUT);
-			usbphycfg |= (USBPHY_OTGVDET_EN | USBPHY_OTGSESSEND_EN
-				| USBPHY_DPOPBUFCTL | USBPHY_DMOPBUFCTL);
-		}
-	} else {
-		if (cpu_is_ti816x())
-			usbphycfg &= ~TI816X_USBPHY0_NORMAL_MODE;
-		else if (cpu_is_ti814x())
-			usbphycfg |= USBPHY_CM_PWRDN | USBPHY_OTG_PWRDN;
-
-	}
-	writel_relaxed(usbphycfg, scm_base + USBCTRL0);
-
-	iounmap(scm_base);
-}

arch/arm/mach-omap2/powerdomain.c

@@ -115,7 +115,6 @@ static int _pwrdm_register(struct powerdomain *pwrdm)
 	}
 	pwrdm->voltdm.ptr = voltdm;
 	INIT_LIST_HEAD(&pwrdm->voltdm_node);
-	voltdm_add_pwrdm(voltdm, pwrdm);
 skip_voltdm:
 	spin_lock_init(&pwrdm->_lock);
 
@@ -483,87 +482,6 @@ pac_exit:
 	return ret;
 }
 
-/**
- * pwrdm_del_clkdm - remove a clockdomain from a powerdomain
- * @pwrdm: struct powerdomain * to add the clockdomain to
- * @clkdm: struct clockdomain * to associate with a powerdomain
- *
- * Dissociate the clockdomain @clkdm from the powerdomain
- * @pwrdm. Returns -EINVAL if presented with invalid pointers; -ENOENT
- * if @clkdm was not associated with the powerdomain, or 0 upon
- * success.
- */
-int pwrdm_del_clkdm(struct powerdomain *pwrdm, struct clockdomain *clkdm)
-{
-	int ret = -EINVAL;
-	int i;
-
-	if (!pwrdm || !clkdm)
-		return -EINVAL;
-
-	pr_debug("powerdomain: %s: dissociating clockdomain %s\n",
-		 pwrdm->name, clkdm->name);
-
-	for (i = 0; i < PWRDM_MAX_CLKDMS; i++)
-		if (pwrdm->pwrdm_clkdms[i] == clkdm)
-			break;
-
-	if (i == PWRDM_MAX_CLKDMS) {
-		pr_debug("powerdomain: %s: clkdm %s not associated?!\n",
-			 pwrdm->name, clkdm->name);
-		ret = -ENOENT;
-		goto pdc_exit;
-	}
-
-	pwrdm->pwrdm_clkdms[i] = NULL;
-
-	ret = 0;
-
-pdc_exit:
-	return ret;
-}
-
-/**
- * pwrdm_for_each_clkdm - call function on each clkdm in a pwrdm
- * @pwrdm: struct powerdomain * to iterate over
- * @fn: callback function *
- *
- * Call the supplied function @fn for each clockdomain in the powerdomain
- * @pwrdm.  The callback function can return anything but 0 to bail
- * out early from the iterator.  Returns -EINVAL if presented with
- * invalid pointers; or passes along the last return value of the
- * callback function, which should be 0 for success or anything else
- * to indicate failure.
- */
-int pwrdm_for_each_clkdm(struct powerdomain *pwrdm,
-			 int (*fn)(struct powerdomain *pwrdm,
-				   struct clockdomain *clkdm))
-{
-	int ret = 0;
-	int i;
-
-	if (!fn)
-		return -EINVAL;
-
-	for (i = 0; i < PWRDM_MAX_CLKDMS && !ret; i++)
-		if (pwrdm->pwrdm_clkdms[i])
-			ret = (*fn)(pwrdm, pwrdm->pwrdm_clkdms[i]);
-
-	return ret;
-}
-
-/**
- * pwrdm_get_voltdm - return a ptr to the voltdm that this pwrdm resides in
- * @pwrdm: struct powerdomain *
- *
- * Return a pointer to the struct voltageomain that the specified powerdomain
- * @pwrdm exists in.
- */
-struct voltagedomain *pwrdm_get_voltdm(struct powerdomain *pwrdm)
-{
-	return pwrdm->voltdm.ptr;
-}
-
 /**
  * pwrdm_get_mem_bank_count - get number of memory banks in this powerdomain
  * @pwrdm: struct powerdomain *

arch/arm/mach-omap2/powerdomain.h

@@ -212,11 +212,6 @@ int pwrdm_for_each_nolock(int (*fn)(struct powerdomain *pwrdm, void *user),
 			void *user);
 
 int pwrdm_add_clkdm(struct powerdomain *pwrdm, struct clockdomain *clkdm);
-int pwrdm_del_clkdm(struct powerdomain *pwrdm, struct clockdomain *clkdm);
-int pwrdm_for_each_clkdm(struct powerdomain *pwrdm,
-			 int (*fn)(struct powerdomain *pwrdm,
-				   struct clockdomain *clkdm));
-struct voltagedomain *pwrdm_get_voltdm(struct powerdomain *pwrdm);
 
 int pwrdm_get_mem_bank_count(struct powerdomain *pwrdm);
 

arch/arm/mach-omap2/prm3xxx.h

@@ -145,7 +145,6 @@ extern void omap3_prm_vcvp_write(u32 val, u8 offset);
 extern u32 omap3_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset);
 
 extern int __init omap3xxx_prm_init(void);
-extern u32 omap3xxx_prm_get_reset_sources(void);
 int omap3xxx_prm_clear_mod_irqs(s16 module, u8 regs, u32 ignore_bits);
 void omap3xxx_prm_iva_idle(void);
 void omap3_prm_reset_modem(void);

arch/arm/mach-omap2/prm44xx_54xx.h

@@ -39,7 +39,6 @@ extern void omap4_prm_vcvp_write(u32 val, u8 offset);
 extern u32 omap4_prm_vcvp_rmw(u32 mask, u32 bits, u8 offset);
 
 extern int __init omap44xx_prm_init(void);
-extern u32 omap44xx_prm_get_reset_sources(void);
 
 #endif
 

arch/arm/mach-omap2/usb-musb.c

@@ -82,16 +82,8 @@ void __init usb_musb_init(struct omap_musb_board_data *musb_board_data)
 	musb_plat.mode = board_data->mode;
 	musb_plat.extvbus = board_data->extvbus;
 
-	if (soc_is_am35xx()) {
-		oh_name = "am35x_otg_hs";
-		name = "musb-am35x";
-	} else if (cpu_is_ti81xx()) {
-		oh_name = "usb_otg_hs";
-		name = "musb-ti81xx";
-	} else {
-		oh_name = "usb_otg_hs";
-		name = "musb-omap2430";
-	}
+	oh_name = "usb_otg_hs";
+	name = "musb-omap2430";
 
         oh = omap_hwmod_lookup(oh_name);
         if (WARN(!oh, "%s: could not find omap_hwmod for %s\n",

arch/arm/mach-omap2/usb.h

@@ -68,5 +68,3 @@ extern void am35x_musb_reset(void);
 extern void am35x_musb_phy_power(u8 on);
 extern void am35x_musb_clear_irq(void);
 extern void am35x_set_mode(u8 musb_mode);
-extern void ti81xx_musb_phy_power(u8 on);
-

arch/arm/mach-omap2/voltage.c

@@ -223,37 +223,6 @@ int omap_voltage_register_pmic(struct voltagedomain *voltdm,
 	return 0;
 }
 
-/**
- * omap_change_voltscale_method() - API to change the voltage scaling method.
- * @voltdm:	pointer to the VDD whose voltage scaling method
- *		has to be changed.
- * @voltscale_method:	the method to be used for voltage scaling.
- *
- * This API can be used by the board files to change the method of voltage
- * scaling between vpforceupdate and vcbypass. The parameter values are
- * defined in voltage.h
- */
-void omap_change_voltscale_method(struct voltagedomain *voltdm,
-				  int voltscale_method)
-{
-	if (!voltdm || IS_ERR(voltdm)) {
-		pr_warn("%s: VDD specified does not exist!\n", __func__);
-		return;
-	}
-
-	switch (voltscale_method) {
-	case VOLTSCALE_VPFORCEUPDATE:
-		voltdm->scale = omap_vp_forceupdate_scale;
-		return;
-	case VOLTSCALE_VCBYPASS:
-		voltdm->scale = omap_vc_bypass_scale;
-		return;
-	default:
-		pr_warn("%s: Trying to change the method of voltage scaling to an unsupported one!\n",
-			__func__);
-	}
-}
-
 /**
  * omap_voltage_late_init() - Init the various voltage parameters
  *
@@ -316,90 +285,11 @@ static struct voltagedomain *_voltdm_lookup(const char *name)
 	return voltdm;
 }
 
-/**
- * voltdm_add_pwrdm - add a powerdomain to a voltagedomain
- * @voltdm: struct voltagedomain * to add the powerdomain to
- * @pwrdm: struct powerdomain * to associate with a voltagedomain
- *
- * Associate the powerdomain @pwrdm with a voltagedomain @voltdm.  This
- * enables the use of voltdm_for_each_pwrdm().  Returns -EINVAL if
- * presented with invalid pointers; -ENOMEM if memory could not be allocated;
- * or 0 upon success.
- */
-int voltdm_add_pwrdm(struct voltagedomain *voltdm, struct powerdomain *pwrdm)
-{
-	if (!voltdm || !pwrdm)
-		return -EINVAL;
-
-	pr_debug("voltagedomain: %s: associating powerdomain %s\n",
-		 voltdm->name, pwrdm->name);
-
-	list_add(&pwrdm->voltdm_node, &voltdm->pwrdm_list);
-
-	return 0;
-}
-
-/**
- * voltdm_for_each_pwrdm - call function for each pwrdm in a voltdm
- * @voltdm: struct voltagedomain * to iterate over
- * @fn: callback function *
- *
- * Call the supplied function @fn for each powerdomain in the
- * voltagedomain @voltdm.  Returns -EINVAL if presented with invalid
- * pointers; or passes along the last return value of the callback
- * function, which should be 0 for success or anything else to
- * indicate failure.
- */
-int voltdm_for_each_pwrdm(struct voltagedomain *voltdm,
-			  int (*fn)(struct voltagedomain *voltdm,
-				    struct powerdomain *pwrdm))
-{
-	struct powerdomain *pwrdm;
-	int ret = 0;
-
-	if (!fn)
-		return -EINVAL;
-
-	list_for_each_entry(pwrdm, &voltdm->pwrdm_list, voltdm_node)
-		ret = (*fn)(voltdm, pwrdm);
-
-	return ret;
-}
-
-/**
- * voltdm_for_each - call function on each registered voltagedomain
- * @fn: callback function *
- *
- * Call the supplied function @fn for each registered voltagedomain.
- * The callback function @fn can return anything but 0 to bail out
- * early from the iterator.  Returns the last return value of the
- * callback function, which should be 0 for success or anything else
- * to indicate failure; or -EINVAL if the function pointer is null.
- */
-int voltdm_for_each(int (*fn)(struct voltagedomain *voltdm, void *user),
-		    void *user)
-{
-	struct voltagedomain *temp_voltdm;
-	int ret = 0;
-
-	if (!fn)
-		return -EINVAL;
-
-	list_for_each_entry(temp_voltdm, &voltdm_list, node) {
-		ret = (*fn)(temp_voltdm, user);
-		if (ret)
-			break;
-	}
-
-	return ret;
-}
-
 static int _voltdm_register(struct voltagedomain *voltdm)
 {
 	if (!voltdm || !voltdm->name)
 		return -EINVAL;
 
-	INIT_LIST_HEAD(&voltdm->pwrdm_list);
 	list_add(&voltdm->node, &voltdm_list);
 
 	pr_debug("voltagedomain: registered %s\n", voltdm->name);

arch/arm/mach-omap2/voltage.h

@@ -23,10 +23,6 @@
 
 struct powerdomain;
 
-/* XXX document */
-#define VOLTSCALE_VPFORCEUPDATE		1
-#define VOLTSCALE_VCBYPASS		2
-
 /*
  * OMAP3 GENERIC setup times. Revisit to see if these needs to be
  * passed from board or PMIC file
@@ -55,7 +51,6 @@ struct omap_vfsm_instance {
  * @name: Name of the voltage domain which can be used as a unique identifier.
  * @scalable: Whether or not this voltage domain is scalable
  * @node: list_head linking all voltage domains
- * @pwrdm_list: list_head linking all powerdomains in this voltagedomain
  * @vc: pointer to VC channel associated with this voltagedomain
  * @vp: pointer to VP associated with this voltagedomain
  * @read: read a VC/VP register
@@ -71,7 +66,6 @@ struct voltagedomain {
 	char *name;
 	bool scalable;
 	struct list_head node;
-	struct list_head pwrdm_list;
 	struct omap_vc_channel *vc;
 	const struct omap_vfsm_instance *vfsm;
 	struct omap_vp_instance *vp;
@@ -163,8 +157,6 @@ struct omap_volt_data *omap_voltage_get_voltdata(struct voltagedomain *voltdm,
 		unsigned long volt);
 int omap_voltage_register_pmic(struct voltagedomain *voltdm,
 			       struct omap_voltdm_pmic *pmic);
-void omap_change_voltscale_method(struct voltagedomain *voltdm,
-		int voltscale_method);
 int omap_voltage_late_init(void);
 
 extern void omap2xxx_voltagedomains_init(void);
@@ -175,11 +167,6 @@ extern void omap54xx_voltagedomains_init(void);
 struct voltagedomain *voltdm_lookup(const char *name);
 void voltdm_init(struct voltagedomain **voltdm_list);
 int voltdm_add_pwrdm(struct voltagedomain *voltdm, struct powerdomain *pwrdm);
-int voltdm_for_each(int (*fn)(struct voltagedomain *voltdm, void *user),
-		    void *user);
-int voltdm_for_each_pwrdm(struct voltagedomain *voltdm,
-			  int (*fn)(struct voltagedomain *voltdm,
-				    struct powerdomain *pwrdm));
 int voltdm_scale(struct voltagedomain *voltdm, unsigned long target_volt);
 void voltdm_reset(struct voltagedomain *voltdm);
 unsigned long voltdm_get_voltage(struct voltagedomain *voltdm);

arch/arm/plat-omap/dma.c

@@ -151,14 +151,6 @@ static int omap_dma_in_1510_mode(void)
 #endif
 
 #ifdef CONFIG_ARCH_OMAP1
-static inline int get_gdma_dev(int req)
-{
-	u32 reg = OMAP_FUNC_MUX_ARM_BASE + ((req - 1) / 5) * 4;
-	int shift = ((req - 1) % 5) * 6;
-
-	return ((omap_readl(reg) >> shift) & 0x3f) + 1;
-}
-
 static inline void set_gdma_dev(int req, int dev)
 {
 	u32 reg = OMAP_FUNC_MUX_ARM_BASE + ((req - 1) / 5) * 4;