arm64: dts: ti: k3-j721e: Add support for pm2 som

The Beta EVMs will be having pm2 SoM which is mainly having Leo PMIC
instead of the prior pm1 SoM which has TPS65917 PMIC. Long term
support is for pm2 SoM.

So k3-j721e-som-p0.dtsi now points to the pm2 SoM &
k3-j721e-common-proc-board is pointing to the boards with pm2 SoM.

The older TPS65917 based pm1 SoMs are renamed to k3-j721e-som-tps65917.dtsi
& ti/k3-j721e-proc-board-tps65917.dts respectively.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Nikhil Devshatwar <nikhil.nd@ti.com>

arch/arm64/boot/dts/ti/Makefile

@@ -21,6 +21,7 @@ dtb-$(CONFIG_ARCH_K3_AM6_SOC) += k3-am654-base-board.dtb \
 	k3-am654-base-board-jailhouse.dtbo
 
 dtb-$(CONFIG_ARCH_K3_J721E_SOC) += k3-j721e-common-proc-board.dtb \
+				   k3-j721e-proc-board-tps65917.dtb \
 				   k3-j721e-common-proc-board-infotainment.dtbo \
 				   k3-j721e-common-proc-board-infotainment-display-sharing.dtbo \
 				   k3-j721e-common-proc-board-jailhouse.dtbo

arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts

@@ -645,7 +645,6 @@
 &main_sdhci1 {
 	/* SD/MMC */
 	vmmc-supply = <&vdd_mmc1>;
-	vqmmc-supply = <&ldo1_reg>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_mmc1_pins_default>;
 };

arch/arm64/boot/dts/ti/k3-j721e-proc-board-tps65917.dts

@@ -0,0 +1,699 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include "k3-j721e-som-tps65917.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/pci/pci.h>
+#include <dt-bindings/sound/ti-mcasp.h>
+
+/ {
+	chosen {
+		stdout-path = "serial2:115200n8";
+		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
+	};
+
+	evm_12v0: fixedregulator-evm12v0 {
+		/* main supply */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_3v3: fixedregulator-vsys3v3 {
+		/* Output of LMS140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_5v0: fixedregulator-vsys5v0 {
+		/* Output of LM5140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	sound0: sound@0 {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "j721e-cpb-analog";
+		simple-audio-card,widgets =
+			"Headphone", "Stereo HP 1",
+			"Headphone", "Stereo HP 2",
+			"Headphone", "Stereo HP 3",
+			"Line", "Line Out",
+			"Microphone", "Stereo Mic 1",
+			"Microphone", "Stereo Mic 2",
+			"Line", "Line In";
+		simple-audio-card,routing =
+			"Stereo HP 1", "AOUT1L",
+			"Stereo HP 1", "AOUT1R",
+			"Stereo HP 2", "AOUT2L",
+			"Stereo HP 2", "AOUT2R",
+			"Stereo HP 3", "AOUT3L",
+			"Stereo HP 3", "AOUT3R",
+			"Line Out", "AOUT4L",
+			"Line Out", "AOUT4R",
+			"AIN1L", "Stereo Mic 1",
+			"AIN1R", "Stereo Mic 1",
+			"AIN2L", "Stereo Mic 2",
+			"AIN2R", "Stereo Mic 2",
+			"AIN3L", "Line In",
+			"AIN3R", "Line In";
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,dai-link@0 {
+			format = "dsp_a";
+			bitclock-master = <&sound0_0_master>;
+			frame-master = <&sound0_0_master>;
+			sound0_0_master: cpu {
+				sound-dai = <&mcasp10>;
+				clocks = <&k3_clks 184 1>;
+				system-clock-id = <MCASP_CLK_HCLK_AUXCLK>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <32>;
+				dai-tdm-slot-tx-mask = <1 1>;
+				dai-tdm-slot-rx-mask = <1 1>;
+			};
+
+			codec {
+				sound-dai = <&pcm3168a_1 0>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <32>;
+				dai-tdm-slot-tx-mask = <1 1>;
+				dai-tdm-slot-rx-mask = <1 1>;
+			};
+		};
+
+		simple-audio-card,dai-link@1 {
+			format = "dsp_a";
+			bitclock-master = <&sound0_1_master>;
+			frame-master = <&sound0_1_master>;
+			sound0_1_master: cpu {
+				sound-dai = <&mcasp10>;
+				clocks = <&k3_clks 184 1>;
+				system-clock-id = <MCASP_CLK_HCLK_AUXCLK>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <32>;
+				dai-tdm-slot-tx-mask = <1 1>;
+				dai-tdm-slot-rx-mask = <1 1>;
+			};
+
+			codec {
+				sound-dai = <&pcm3168a_1 1>;
+				dai-tdm-slot-num = <2>;
+				dai-tdm-slot-width = <32>;
+				dai-tdm-slot-tx-mask = <1 1>;
+				dai-tdm-slot-rx-mask = <1 1>;
+			};
+		};
+	};
+
+	vdd_mmc1: fixedregulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mmc1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		vin-supply = <&vsys_3v3>;
+		gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	dp0: connector {
+		compatible = "dp-connector"; /* No such binding exists yet.. */
+
+		port {
+			dp_connector_in: endpoint {
+			remote-endpoint = <&dp_bridge_output>;
+			};
+		};
+	};
+};
+
+&wkup_pmx0 {
+	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
+			J721E_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
+			J721E_WKUP_IOPAD(0x0060, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
+			J721E_WKUP_IOPAD(0x0064, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
+			J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
+			J721E_WKUP_IOPAD(0x006c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
+			J721E_WKUP_IOPAD(0x0078, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
+			J721E_WKUP_IOPAD(0x007c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
+			J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
+			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
+			J721E_WKUP_IOPAD(0x0070, PIN_INPUT, 0) /* MCU_RGMII1_TXC */
+			J721E_WKUP_IOPAD(0x0074, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
+		>;
+	};
+
+	mcu_mdio_pins_default: mcu_mdio1_pins_default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* MCU_MDIO0_MDC */
+			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_MDIO0_MDIO */
+		>;
+	};
+
+	mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x34, PIN_OUTPUT, 0) /* (F22) MCU_OSPI1_CLK */
+			J721E_WKUP_IOPAD(0x50, PIN_OUTPUT, 0) /* (C22) MCU_OSPI1_CSn0 */
+			J721E_WKUP_IOPAD(0x40, PIN_INPUT, 0) /* (D22) MCU_OSPI1_D0 */
+			J721E_WKUP_IOPAD(0x44, PIN_INPUT, 0) /* (G22) MCU_OSPI1_D1 */
+			J721E_WKUP_IOPAD(0x48, PIN_INPUT, 0) /* (D23) MCU_OSPI1_D2 */
+			J721E_WKUP_IOPAD(0x4c, PIN_INPUT, 0) /* (C23) MCU_OSPI1_D3 */
+			J721E_WKUP_IOPAD(0x3c, PIN_INPUT, 0) /* (B23) MCU_OSPI1_DQS */
+			J721E_WKUP_IOPAD(0x38, PIN_INPUT, 0) /* (A23) MCU_OSPI1_LBCLKO */
+		>;
+	};
+};
+
+&wkup_uart0 {
+	/* Wakeup UART is used by System firmware */
+	status = "disabled";
+};
+
+&main_uart3 {
+	/* UART not brought out */
+	status = "disabled";
+};
+
+&main_uart5 {
+	/* UART not brought out */
+	status = "disabled";
+};
+
+&main_uart6 {
+	/* UART not brought out */
+	status = "disabled";
+};
+
+&main_uart7 {
+	/* UART not brought out */
+	status = "disabled";
+};
+
+&main_uart8 {
+	/* UART not brought out */
+	status = "disabled";
+};
+
+&main_uart9 {
+	/* UART not brought out */
+	status = "disabled";
+};
+
+&main_gpio2 {
+	status = "disabled";
+};
+
+&main_gpio3 {
+	status = "disabled";
+};
+
+&main_gpio4 {
+	status = "disabled";
+};
+
+&main_gpio5 {
+	status = "disabled";
+};
+
+&main_gpio6 {
+	status = "disabled";
+};
+
+&main_gpio7 {
+	status = "disabled";
+};
+
+&wkup_gpio1 {
+	status = "disabled";
+};
+
+&main_pmx0 {
+	main_i2c1_exp4_pins_default: main-i2c1-exp4-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x230, PIN_INPUT, 7) /* (U2) ECAP0_IN_APWM_OUT.GPIO1_11 */
+		>;
+	};
+
+	main_i2c0_pins_default: main-i2c0-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
+			J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
+		>;
+	};
+
+	main_i2c1_pins_default: main-i2c1-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */
+			J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */
+		>;
+	};
+
+	main_i2c3_pins_default: main-i2c3-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */
+			J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */
+		>;
+	};
+
+	main_i2c6_pins_default: main-i2c6-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x1d0, PIN_INPUT_PULLUP, 2) /* (AA3) SPI0_D1.I2C6_SCL */
+			J721E_IOPAD(0x1e4, PIN_INPUT_PULLUP, 2) /* (Y2) SPI1_D1.I2C6_SDA */
+		>;
+	};
+
+	mcasp10_pins_default: mcasp10_pins_default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x158, PIN_OUTPUT_PULLDOWN, 12) /* (U23) RGMII5_TX_CTL.MCASP10_ACLKX */
+			J721E_IOPAD(0x15c, PIN_OUTPUT_PULLDOWN, 12) /* (U26) RGMII5_RX_CTL.MCASP10_AFSX */
+			J721E_IOPAD(0x160, PIN_INPUT_PULLDOWN, 12) /* (V28) RGMII5_TD3.MCASP10_AXR0 */
+			J721E_IOPAD(0x164, PIN_INPUT_PULLDOWN, 12) /* (V29) RGMII5_TD2.MCASP10_AXR1 */
+			J721E_IOPAD(0x170, PIN_INPUT_PULLDOWN, 12) /* (U29) RGMII5_TXC.MCASP10_AXR2 */
+			J721E_IOPAD(0x174, PIN_OUTPUT_PULLDOWN, 12) /* (U25) RGMII5_RXC.MCASP10_AXR3 */
+			J721E_IOPAD(0x198, PIN_OUTPUT_PULLDOWN, 12) /* (V25) RGMII6_TD1.MCASP10_AXR4 */
+			J721E_IOPAD(0x19c, PIN_OUTPUT_PULLDOWN, 12) /* (W27) RGMII6_TD0.MCASP10_AXR5 */
+			J721E_IOPAD(0x1a0, PIN_OUTPUT_PULLDOWN, 12) /* (W29) RGMII6_TXC.MCASP10_AXR6 */
+		>;
+	};
+
+	audi_ext_refclk2_pins_default: audi_ext_refclk2_pins_default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x1a4, PIN_OUTPUT, 3) /* (W26) RGMII6_RXC.AUDIO_EXT_REFCLK2 */
+		>;
+	};
+
+	main_usbss0_pins_default: main_usbss0_pins_default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
+			J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
+		>;
+	};
+
+	main_usbss1_pins_default: main_usbss1_pins_default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
+		>;
+	};
+
+	main_mmc1_pins_default: main_mmc1_pins_default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
+			J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
+			J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */
+			J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
+			J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */
+			J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
+			J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
+			J721E_IOPAD(0x25c, PIN_INPUT, 0) /* (R28) MMC1_SDWP */
+			J721E_IOPAD(0x2ac, PIN_INPUT, 0)
+		>;
+	};
+
+	dp0_pins_default: dp0_pins_default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x1c4, PIN_INPUT, 5) /* SPI0_CS1.DP0_HPD */
+		>;
+	};
+};
+
+&dss {
+	status = "ok";
+};
+
+&dss_ports {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@0 {
+		reg = <0>;
+
+		dpi_out_real0: endpoint {
+			remote-endpoint = <&dp_bridge_input>;
+		};
+	};
+};
+
+&main_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	exp1: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	exp2: gpio@22 {
+		compatible = "ti,tca6424";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		p09 {
+			/* P11 - MCASP/TRACE_MUX_S0 */
+			gpio-hog;
+			gpios = <9 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "MCASP/TRACE_MUX_S0";
+		};
+
+		p10 {
+			/* P12 - MCASP/TRACE_MUX_S1 */
+			gpio-hog;
+			gpios = <10 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "MCASP/TRACE_MUX_S1";
+		};
+	};
+};
+
+&main_i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c1_pins_default>;
+	clock-frequency = <400000>;
+
+	exp4: gpio@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&main_i2c1_exp4_pins_default>;
+		interrupt-parent = <&main_gpio1>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		p0 {
+			/* P0 - DP0_PWR_SW_EN */
+			gpio-hog;
+			gpios = <0 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "DP0_PWR_SW_EN";
+		};
+	};
+};
+
+&main_i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c3_pins_default>;
+	clock-frequency = <400000>;
+
+	exp3: gpio@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		p0 {
+			/* P0 - CODEC_RSTz */
+			gpio-hog;
+			gpios = <0 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "CODEC_RSTz";
+		};
+	};
+
+	pcm3168a_1: audio-codec@44 {
+		compatible = "ti,pcm3168a";
+		reg = <0x44>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&audi_ext_refclk2_pins_default>;
+
+		#sound-dai-cells = <1>;
+
+		/* C_AUDIO_REFCLK2 -> RGMII6_RXC (W26) */
+		clocks = <&k3_clks 157 371>;
+		clock-names = "scki";
+
+		/* HSDIV3_16FFT_MAIN_4_HSDIVOUT2_CLK -> REFCLK2 */
+		assigned-clocks = <&k3_clks 157 371>;
+		assigned-clock-parents = <&k3_clks 157 400>;
+		assigned-clock-rates = <24576000>; /* for 48KHz */
+
+		VDD1-supply = <&vsys_3v3>;
+		VDD2-supply = <&vsys_3v3>;
+		VCCAD1-supply = <&vsys_5v0>;
+		VCCAD2-supply = <&vsys_5v0>;
+		VCCDA1-supply = <&vsys_5v0>;
+		VCCDA2-supply = <&vsys_5v0>;
+	};
+};
+
+&main_i2c6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c6_pins_default>;
+	clock-frequency = <400000>;
+
+	exp5: gpio@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&mcu_cpsw {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
+
+	cpts {
+		ti,pps = <3 1>;
+	};
+};
+
+&davinci_mdio {
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+	};
+};
+
+&cpsw_port1 {
+	phy-mode = "rgmii-id";
+	phy-handle = <&phy0>;
+};
+
+#define TS_OFFSET(pa, val)     (0x4 + (pa) * 4) (0x10000 | val)
+
+&timesync_router {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_cpts>;
+
+	mcu_cpts: mcu_cpts {
+		pinctrl-single,pins = <
+			/* pps [cpts genf1] in17 -> out25 [cpts hw4_push] */
+			TS_OFFSET(25, 17)
+		>;
+	};
+};
+
+&ospi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
+
+	flash@0{
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <100000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <2>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&mcasp10 {
+	#sound-dai-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcasp10_pins_default>;
+
+	op-mode = <0>;		/* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+	auxclk-fs-ratio = <256>;
+
+	serial-dir = <	/* 0: INACTIVE, 1: TX, 2: RX */
+		2 2 2 1
+		1 1 1 0
+	>;
+	tx-num-evt = <0>;
+	rx-num-evt = <0>;
+
+	status = "okay";
+};
+
+&usb_serdes_mux {
+	idle-states = <1>, <0>; /* USB0 to SERDES3, USB1 to SERDES1 */
+};
+
+&serdes_ln_ctrl {
+	idle-states = <SERDES0_LANE0_PCIE0_LANE0>, <SERDES0_LANE1_PCIE0_LANE1>,
+		      <SERDES1_LANE0_PCIE1_LANE0>, <SERDES1_LANE1_PCIE1_LANE1>,
+		      <SERDES2_LANE0_PCIE2_LANE0>, <SERDES2_LANE1_PCIE2_LANE1>,
+		      <SERDES3_LANE0_USB3_0_SWAP>, <SERDES3_LANE1_USB3_0>,
+		      <SERDES4_LANE0_EDP_LANE0>, <SERDES4_LANE1_EDP_LANE1>, <SERDES4_LANE2_EDP_LANE2>, <SERDES4_LANE3_EDP_LANE3>;
+};
+
+&serdes_wiz3 {
+	typec-dir-gpios = <&main_gpio1 3 GPIO_ACTIVE_HIGH>;
+};
+
+&serdes3 {
+	serdes3_usb_link: link@0 {
+		reg = <0>;
+		cdns,num-lanes = <2>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_USB3>;
+		resets = <&serdes_wiz3 1>, <&serdes_wiz3 2>;
+	};
+};
+
+&usbss0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_usbss0_pins_default>;
+	ti,vbus-divider;
+};
+
+&usb0 {
+	dr_mode = "otg";
+	maximum-speed = "super-speed";
+	phys = <&serdes3_usb_link>;
+	phy-names = "cdns3,usbphy";
+};
+
+&usbss1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_usbss1_pins_default>;
+	ti,usb2-only;
+};
+
+&usb1 {
+	dr_mode = "host";
+	maximum-speed = "high-speed";
+};
+
+&main_sdhci0 {
+	/* eMMC */
+	non-removable;
+	ti,driver-strength-ohm = <50>;
+};
+
+&main_sdhci1 {
+	/* SD/MMC */
+	vmmc-supply = <&vdd_mmc1>;
+	vqmmc-supply = <&ldo1_reg>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mmc1_pins_default>;
+};
+
+&main_sdhci2 {
+	/* Unused */
+	status = "disabled";
+};
+
+&serdes0 {
+	serdes0_pcie_link: link@0 {
+		reg = <0>;
+		cdns,num-lanes = <1>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_PCIE>;
+		resets = <&serdes_wiz0 1>;
+	};
+};
+
+&serdes1 {
+	serdes1_pcie_link: link@0 {
+		reg = <0>;
+		cdns,num-lanes = <2>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_PCIE>;
+		resets = <&serdes_wiz1 1>, <&serdes_wiz1 2>;
+	};
+};
+
+&serdes2 {
+	serdes2_pcie_link: link@0 {
+		reg = <0>;
+		cdns,num-lanes = <2>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_PCIE>;
+		resets = <&serdes_wiz2 1>, <&serdes_wiz2 2>;
+	};
+};
+
+&pcie0 {
+	pci-mode = <PCI_MODE_RC>;
+	num-lanes = <1>;
+};
+
+&pcie1 {
+	pci-mode = <PCI_MODE_RC>;
+	num-lanes = <2>;
+};
+
+&pcie2 {
+	pci-mode = <PCI_MODE_RC>;
+	num-lanes = <2>;
+};
+
+&pcie0_rc {
+	reset-gpios = <&exp1 6 GPIO_ACTIVE_HIGH>;
+	phys = <&serdes0_pcie_link>;
+	phy-names = "pcie_phy";
+};
+
+&pcie1_rc {
+	reset-gpios = <&exp1 2 GPIO_ACTIVE_HIGH>;
+	phys = <&serdes1_pcie_link>;
+	phy-names = "pcie_phy";
+};
+
+&pcie2_rc {
+	reset-gpios = <&exp2 20 GPIO_ACTIVE_HIGH>;
+	phys = <&serdes2_pcie_link>;
+	phy-names = "pcie_phy";
+};
+
+&tscadc0 {
+	adc {
+		ti,adc-channels = <0 1 2 3 4 5 6 7>;
+	};
+};
+
+&tscadc1 {
+	adc {
+		ti,adc-channels = <0 1 2 3 4 5 6 7>;
+	};
+};

arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi

@@ -186,43 +186,6 @@
 	};
 };
 
-&wkup_i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&wkup_i2c0_pins_default>;
-	clock-frequency = <400000>;
-
-	tps65917: tps65917@58 {
-		reg = <0x58>;
-		compatible = "ti,tps65917";
-
-		tps65917_pmic {
-			compatible = "ti,tps65917-pmic";
-
-			ldo1-in-supply = <&vsys_3v3>;
-
-			tps65917_regulators: regulators {
-				ldo1_reg: ldo1 {
-					/* LDO1_OUT --> VDD_SD_DV_REG  */
-					regulator-name = "ldo1";
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-allow-bypass;
-				};
-
-				ldo2_reg: ldo2 {
-					/* LDO2_OUT --> VDA_USB_3V3_REG  */
-					regulator-name = "ldo2";
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-					regulator-allow-bypass;
-					regulator-always-on;
-					regulator-boot-on;
-				};
-			};
-		};
-	};
-};
-
 &ospi0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;

arch/arm64/boot/dts/ti/k3-j721e-som-tps65917.dtsi

@@ -0,0 +1,307 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include "k3-j721e.dtsi"
+
+/ {
+	memory@80000000 {
+		device_type = "memory";
+		/* 4G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
+		      <0x00000008 0x80000000 0x00000000 0x80000000>;
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>;
+			alignment = <0x1000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa0000000 0x00 0x100000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core0_memory_region: r5f-memory@a0100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa0100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa1000000 0x00 0x100000>;
+			no-map;
+		};
+
+		mcu_r5fss0_core1_memory_region: r5f-memory@a1100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa1100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a2000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa2000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss0_core0_memory_region: r5f-memory@a2100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa2100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a3000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa3000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss0_core1_memory_region: r5f-memory@a3100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa3100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss1_core0_dma_memory_region: r5f-dma-memory@a4000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa4000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss1_core0_memory_region: r5f-memory@a4100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa4100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		main_r5fss1_core1_dma_memory_region: r5f-dma-memory@a5000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa5000000 0x00 0x100000>;
+			no-map;
+		};
+
+		main_r5fss1_core1_memory_region: r5f-memory@a5100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa5100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		c66_1_dma_memory_region: c66-dma-memory@a6000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa6000000 0x00 0x100000>;
+			no-map;
+		};
+
+		c66_0_memory_region: c66-memory@a6100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa6100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		c66_0_dma_memory_region: c66-dma-memory@a7000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa7000000 0x00 0x100000>;
+			no-map;
+		};
+
+		c66_1_memory_region: c66-memory@a7100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa7100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		c71_0_dma_memory_region: c71-dma-memory@a8000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa8000000 0x00 0x100000>;
+			no-map;
+		};
+
+		c71_0_memory_region: c71-memory@a8100000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0xa8100000 0x00 0xf00000>;
+			no-map;
+		};
+
+		rtos_ipc_memory_region: ipc-memories@aa000000 {
+			reg = <0x00 0xaa000000 0x00 0x01c00000>;
+			alignment = <0x1000>;
+			no-map;
+		};
+	};
+};
+
+&wkup_pmx0 {
+	wkup_i2c0_pins_default: wkup_i2c0_pins_default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
+			J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
+		>;
+	};
+
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */
+			J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0)  /* MCU_OSPI0_DQS */
+			J721E_WKUP_IOPAD(0x000c, PIN_INPUT, 0)  /* MCU_OSPI0_D0 */
+			J721E_WKUP_IOPAD(0x0010, PIN_INPUT, 0)  /* MCU_OSPI0_D1 */
+			J721E_WKUP_IOPAD(0x0014, PIN_INPUT, 0)  /* MCU_OSPI0_D2 */
+			J721E_WKUP_IOPAD(0x0018, PIN_INPUT, 0)  /* MCU_OSPI0_D3 */
+			J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0)  /* MCU_OSPI0_D4 */
+			J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0)  /* MCU_OSPI0_D5 */
+			J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0)  /* MCU_OSPI0_D6 */
+			J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0)  /* MCU_OSPI0_D7 */
+			J721E_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* MCU_OSPI0_CSn0 */
+		>;
+	};
+
+	mcu_fss0_hpb0_pins_default: mcu-fss0-hpb0-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x0, PIN_OUTPUT, 1) /* (E20) MCU_OSPI0_CLK.MCU_HYPERBUS0_CK */
+			J721E_WKUP_IOPAD(0x4, PIN_OUTPUT, 1) /* (C21) MCU_OSPI0_LBCLKO.MCU_HYPERBUS0_CKn */
+			J721E_WKUP_IOPAD(0x2c, PIN_OUTPUT, 1) /* (F19) MCU_OSPI0_CSn0.MCU_HYPERBUS0_CSn0 */
+			J721E_WKUP_IOPAD(0x54, PIN_OUTPUT, 3) /* (E22) MCU_OSPI1_CSn1.MCU_HYPERBUS0_CSn1 */
+			J721E_WKUP_IOPAD(0x30, PIN_OUTPUT, 1) /* (E19) MCU_OSPI0_CSn1.MCU_HYPERBUS0_RESETn */
+			J721E_WKUP_IOPAD(0x8, PIN_INPUT, 1) /* (D21) MCU_OSPI0_DQS.MCU_HYPERBUS0_RWDS */
+			J721E_WKUP_IOPAD(0xc, PIN_INPUT, 1) /* (D20) MCU_OSPI0_D0.MCU_HYPERBUS0_DQ0 */
+			J721E_WKUP_IOPAD(0x10, PIN_INPUT, 1) /* (G19) MCU_OSPI0_D1.MCU_HYPERBUS0_DQ1 */
+			J721E_WKUP_IOPAD(0x14, PIN_INPUT, 1) /* (G20) MCU_OSPI0_D2.MCU_HYPERBUS0_DQ2 */
+			J721E_WKUP_IOPAD(0x18, PIN_INPUT, 1) /* (F20) MCU_OSPI0_D3.MCU_HYPERBUS0_DQ3 */
+			J721E_WKUP_IOPAD(0x1c, PIN_INPUT, 1) /* (F21) MCU_OSPI0_D4.MCU_HYPERBUS0_DQ4 */
+			J721E_WKUP_IOPAD(0x20, PIN_INPUT, 1) /* (E21) MCU_OSPI0_D5.MCU_HYPERBUS0_DQ5 */
+			J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (B22) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */
+			J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (G21) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */
+		>;
+	};
+};
+
+&wkup_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	tps65917: tps65917@58 {
+		reg = <0x58>;
+		compatible = "ti,tps65917";
+
+		tps65917_pmic {
+			compatible = "ti,tps65917-pmic";
+
+			ldo1-in-supply = <&vsys_3v3>;
+
+			tps65917_regulators: regulators {
+				ldo1_reg: ldo1 {
+					/* LDO1_OUT --> VDD_SD_DV_REG  */
+					regulator-name = "ldo1";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-allow-bypass;
+				};
+
+				ldo2_reg: ldo2 {
+					/* LDO2_OUT --> VDA_USB_3V3_REG  */
+					regulator-name = "ldo2";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-allow-bypass;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+			};
+		};
+	};
+};
+
+&ospi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+	flash@0{
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <50000000>;
+		spi-dqs;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <0>;
+		cdns,phy-mode;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&mcu_r5fss0_core0 {
+	memory-region = <&mcu_r5fss0_core0_dma_memory_region>,
+			<&mcu_r5fss0_core0_memory_region>;
+};
+
+&mcu_r5fss0_core1 {
+	memory-region = <&mcu_r5fss0_core1_dma_memory_region>,
+			<&mcu_r5fss0_core1_memory_region>;
+};
+
+&main_r5fss0_core0 {
+	memory-region = <&main_r5fss0_core0_dma_memory_region>,
+			<&main_r5fss0_core0_memory_region>;
+};
+
+&main_r5fss0_core1 {
+	memory-region = <&main_r5fss0_core1_dma_memory_region>,
+			<&main_r5fss0_core1_memory_region>;
+};
+
+&main_r5fss1_core0 {
+	memory-region = <&main_r5fss1_core0_dma_memory_region>,
+			<&main_r5fss1_core0_memory_region>;
+};
+
+&main_r5fss1_core1 {
+	memory-region = <&main_r5fss1_core1_dma_memory_region>,
+			<&main_r5fss1_core1_memory_region>;
+};
+
+&c66_0 {
+	memory-region = <&c66_0_dma_memory_region>,
+			<&c66_0_memory_region>;
+};
+
+&c66_1 {
+	memory-region = <&c66_1_dma_memory_region>,
+			<&c66_1_memory_region>;
+};
+
+&c71_0 {
+	memory-region = <&c71_0_dma_memory_region>,
+			<&c71_0_memory_region>;
+};
+
+&hbmc {
+	/* OSPI and HBMC are muxed inside FSS, Bootloader will enable
+	 * appropriate node based on board detection
+	 */
+	status = "disabled";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_hpb0_pins_default>;
+	ranges = <0x0 0x0 0x5 0x00000000 0x4000000>, /* 64MB Flash on CS0 */
+		 <0x1 0x0 0x5 0x04000000 0x800000>; /* 8MB RAM on CS1 */
+
+	flash@0,0 {
+		compatible = "cypress,hyperflash", "cfi-flash";
+		reg = <0x0 0x0 0x4000000>;
+	};
+};