Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC DT updates from Olof Johansson:
 "Device tree and bindings updates for 3.12.

  General additions of various on-chip and on-board peripherals on
  various platforms as support gets added.  Some of the bigger changes
  are:

   - Addition of (new) PCI-e support on Tegra.
   - More Tegra4 support, including PMC configuration for Dalmore.
   - Addition of a new board for Exynos4 (trats2) and more bindings for
     4x12 IP.
   - Addition of Allwinner A20 and A31 SoC and board files.
   - Move of the ST Ericsson device tree files to now use ste-* prefix.
   - More move of hardware description of shmobile platforms to DT.
   - Two new board dts files for Freescale MXs"

* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (177 commits)
  dts: Rename DW APB timer compatible strings
  dts: Deprecate ALTR as a vendor prefix
  of: add vendor prefix for Altera Corp.
  ARM: at91/dt: sam9x5ek: add sound configuration
  ARM: at91/dt: sam9x5ek: enable SSC
  ARM: at91/dt: sam9x5ek: add WM8731 codec
  ARM: at91/dt: sam9x5: add SSC DMA parameters
  ARM: at91/dt: add at91rm9200 PQFP package version
  ARM: at91: at91rm9200: set default mmc0 pinctrl-names
  ARM: at91: at91sam9n12: correct pin number of gpio-key
  ARM: at91: at91sam9n12: add qt1070 support
  ARM: at91: at91sam9n12: add pinctrl of TWI
  ARM: at91: Add PMU support for sama5d3
  ARM: at91: at91sam9260: add missing pinctrl-names on mmc
  ARM: tegra: configure power off for Dalmore
  ARM: DT: binding fixup to align with vendor-prefixes.txt (DT)
  ARM: dts: add sdio blocks to bcm28155-ap board
  ARM: dts: align sdio numbers to HW definition
  ARM: sun7i: Add Olimex A20-Olinuxino-Micro support
  ARM: sun7i: Add Allwinner A20 DTSI
  ...

Documentation/devicetree/bindings/arm/bcm/bcm11351.txt

@@ -6,4 +6,5 @@ bcm11351, bcm28145, bcm28155 SoCs) shall have the following properties:
 
 Required root node property:
 
-compatible = "bcm,bcm11351";
+compatible = "brcm,bcm11351";
+DEPRECATED: compatible = "bcm,bcm11351";

Documentation/devicetree/bindings/arm/bcm/bcm,kona-timer.txt → Documentation/devicetree/bindings/arm/bcm/kona-timer.txt

@@ -4,14 +4,15 @@ This timer is used in the following Broadcom SoCs:
  BCM11130, BCM11140, BCM11351, BCM28145, BCM28155
 
 Required properties:
-- compatible : "bcm,kona-timer"
+- compatible : "brcm,kona-timer"
+- DEPRECATED: compatible : "bcm,kona-timer"
 - reg : Register range for the timer
 - interrupts : interrupt for the timer
 - clock-frequency: frequency that the clock operates
 
 Example:
 	timer@35006000 {
-		compatible = "bcm,kona-timer";
+		compatible = "brcm,kona-timer";
 		reg = <0x35006000 0x1000>;
 		interrupts = <0x0 7 0x4>;
 		clock-frequency = <32768>;

Documentation/devicetree/bindings/arm/bcm/kona-wdt.txt

@@ -0,0 +1,15 @@
+Broadcom Kona Family Watchdog Timer
+-----------------------------------
+
+This watchdog timer is used in the following Broadcom SoCs:
+  BCM11130, BCM11140, BCM11351, BCM28145, BCM28155
+
+Required properties:
+  - compatible = "brcm,bcm11351-wdt", "brcm,kona-wdt";
+  - reg: memory address & range
+
+Example:
+	watchdog@35002f40 {
+		compatible = "brcm,bcm11351-wdt", "brcm,kona-wdt";
+		reg = <0x35002f40 0x6c>;
+	};

Documentation/devicetree/bindings/media/s5p-mfc.txt

@@ -16,9 +16,9 @@ Required properties:
 	  mapped region.
 
   - interrupts : MFC interrupt number to the CPU.
-  - clocks : from common clock binding: handle to mfc clocks.
-  - clock-names : from common clock binding: must contain "sclk_mfc" and "mfc",
-		  corresponding to entries in the clocks property.
+  - clocks : from common clock binding: handle to mfc clock.
+  - clock-names : from common clock binding: must contain "mfc",
+		  corresponding to entry in the clocks property.
 
   - samsung,mfc-r : Base address of the first memory bank used by MFC
 		    for DMA contiguous memory allocation and its size.
@@ -38,8 +38,8 @@ mfc: codec@13400000 {
 	reg = <0x13400000 0x10000>;
 	interrupts = <0 94 0>;
 	samsung,power-domain = <&pd_mfc>;
-	clocks = <&clock 170>, <&clock 273>;
-	clock-names = "sclk_mfc", "mfc";
+	clocks = <&clock 273>;
+	clock-names = "mfc";
 };
 
 Board specific DT entry:

Documentation/devicetree/bindings/misc/smc.txt

@@ -4,11 +4,12 @@ This binding defines the location of the bounce buffer
 used for non-secure to secure communications.
 
 Required properties:
-- compatible : "bcm,kona-smc"
+- compatible : "brcm,kona-smc"
+- DEPRECATED: compatible : "bcm,kona-smc"
 - reg : Location and size of bounce buffer
 
 Example:
 	smc@0x3404c000 {
-		compatible = "bcm,bcm11351-smc", "bcm,kona-smc";
+		compatible = "brcm,bcm11351-smc", "brcm,kona-smc";
 		reg = <0x3404c000 0x400>; //1 KiB in SRAM
 	};

Documentation/devicetree/bindings/mmc/bcm,kona-sdhci.txt → Documentation/devicetree/bindings/mmc/kona-sdhci.txt

@@ -4,12 +4,13 @@ This file documents differences between the core properties in mmc.txt
 and the properties present in the bcm281xx SDHCI
 
 Required properties:
-- compatible : Should be "bcm,kona-sdhci"
+- compatible : Should be "brcm,kona-sdhci"
+- DEPRECATED: compatible : Should be "bcm,kona-sdhci"
 
 Example:
 
 sdio2: sdio@0x3f1a0000 {
-	compatible = "bcm,kona-sdhci";
+	compatible = "brcm,kona-sdhci";
 	reg = <0x3f1a0000 0x10000>;
 	interrupts = <0x0 74 0x4>;
 };

Documentation/devicetree/bindings/pinctrl/nvidia,tegra114-pinmux.txt

@@ -80,6 +80,17 @@ Valid values for pin and group names are:
     dbg, sdio3, spi, uaa, uab, uart2, uart3, sdio1, ddc, gma, gme, gmf, gmg,
     gmh, owr, uda.
 
+Valid values for nvidia,functions are:
+
+  blink, cec, cldvfs, clk12, cpu, dap, dap1, dap2, dev3, displaya,
+  displaya_alt, displayb, dtv, emc_dll, extperiph1, extperiph2,
+  extperiph3, gmi, gmi_alt, hda, hsi, i2c1, i2c2, i2c3, i2c4, i2cpwr,
+  i2s0, i2s1, i2s2, i2s3, i2s4, irda, kbc, nand, nand_alt, owr, pmi,
+  pwm0, pwm1, pwm2, pwm3, pwron, reset_out_n, rsvd1, rsvd2, rsvd3,
+  rsvd4, sdmmc1, sdmmc2, sdmmc3, sdmmc4, soc, spdif, spi1, spi2, spi3,
+  spi4, spi5, spi6, sysclk, trace, uarta, uartb, uartc, uartd, ulpi,
+  usb, vgp1, vgp2, vgp3, vgp4, vgp5, vgp6, vi, vi_alt1, vi_alt3
+
 Example:
 
 	pinmux: pinmux {

Documentation/devicetree/bindings/pinctrl/nvidia,tegra20-pinmux.txt

@@ -103,6 +103,17 @@ Valid values for pin and group names are:
     drive_gma, drive_gmb, drive_gmc, drive_gmd, drive_gme, drive_owr,
     drive_uda.
 
+Valid values for nvidia,functions are:
+
+  ahb_clk, apb_clk, audio_sync, crt, dap1, dap2, dap3, dap4, dap5,
+  displaya, displayb, emc_test0_dll, emc_test1_dll, gmi, gmi_int,
+  hdmi, i2cp, i2c1, i2c2, i2c3, ide, irda, kbc, mio, mipi_hs, nand,
+  osc, owr, pcie, plla_out, pllc_out1, pllm_out1, pllp_out2, pllp_out3,
+  pllp_out4, pwm, pwr_intr, pwr_on, rsvd1, rsvd2, rsvd3, rsvd4, rtck,
+  sdio1, sdio2, sdio3, sdio4, sflash, spdif, spi1, spi2, spi2_alt,
+  spi3, spi4, trace, twc, uarta, uartb, uartc, uartd, uarte, ulpi,
+  vi, vi_sensor_clk, xio
+
 Example:
 
 	pinctrl@70000000 {

Documentation/devicetree/bindings/pinctrl/nvidia,tegra30-pinmux.txt

@@ -91,6 +91,18 @@ Valid values for pin and group names are:
     gmh, gpv, lcd1, lcd2, owr, sdio1, sdio2, sdio3, spi, uaa, uab, uart2,
     uart3, uda, vi1.
 
+Valid values for nvidia,functions are:
+
+  blink, cec, clk_12m_out, clk_32k_in, core_pwr_req, cpu_pwr_req, crt,
+  dap, ddr, dev3, displaya, displayb, dtv, extperiph1, extperiph2,
+  extperiph3, gmi, gmi_alt, hda, hdcp, hdmi, hsi, i2c1, i2c2, i2c3,
+  i2c4, i2cpwr, i2s0, i2s1, i2s2, i2s3, i2s4, invalid, kbc, mio, nand,
+  nand_alt, owr, pcie, pwm0, pwm1, pwm2, pwm3, pwr_int_n, rsvd1, rsvd2,
+  rsvd3, rsvd4, rtck, sata, sdmmc1, sdmmc2, sdmmc3, sdmmc4, spdif, spi1,
+  spi2, spi2_alt, spi3, spi4, spi5, spi6, sysclk, test, trace, uarta,
+  uartb, uartc, uartd, uarte, ulpi, vgp1, vgp2, vgp3, vgp4, vgp5, vgp6,
+  vi, vi_alt1, vi_alt2, vi_alt3
+
 Example:
 
 	pinctrl@70000000 {

Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt

@@ -1,8 +1,8 @@
 ST Ericsson Nomadik pinmux controller
 
 Required properties:
-- compatible: "stericsson,nmk-pinctrl", "stericsson,nmk-pinctrl-db8540",
-              "stericsson,nmk-pinctrl-stn8815"
+- compatible: "stericsson,db8500-pinctrl", "stericsson,db8540-pinctrl",
+              "stericsson,stn8815-pinctrl"
 - reg: Should contain the register physical address and length of the PRCMU.
 
 Please refer to pinctrl-bindings.txt in this directory for details of the
@@ -68,7 +68,7 @@ Optional subnode-properties:
 Example board file extract:
 
 	pinctrl@80157000 {
-		compatible = "stericsson,nmk-pinctrl";
+		compatible = "stericsson,db8500-pinctrl";
 		reg = <0x80157000 0x2000>;
 
 		pinctrl-names = "default";

Documentation/devicetree/bindings/rtc/dw-apb.txt

@@ -1,7 +1,10 @@
 * Designware APB timer
 
 Required properties:
-- compatible: "snps,dw-apb-timer-sp" or "snps,dw-apb-timer-osc"
+- compatible: One of:
+ 	"snps,dw-apb-timer"
+	"snps,dw-apb-timer-sp" <DEPRECATED>
+	"snps,dw-apb-timer-osc" <DEPRECATED>
 - reg: physical base address of the controller and length of memory mapped
   region.
 - interrupts: IRQ line for the timer.
@@ -20,25 +23,10 @@ systems may use one.
 
 
 Example:
-
-		timer1: timer@ffc09000 {
-				compatible = "snps,dw-apb-timer-sp";
-				interrupts = <0 168 4>;
-				clock-frequency = <200000000>;
-				reg = <0xffc09000 0x1000>;
-			};
-
-		timer2: timer@ffd00000 {
-				compatible = "snps,dw-apb-timer-osc";
-				interrupts = <0 169 4>;
-				clock-frequency = <200000000>;
-				reg = <0xffd00000 0x1000>;
-			};
-
-		timer3: timer@ffe00000 {
-				compatible = "snps,dw-apb-timer-osc";
-				interrupts = <0 170 4>;
-				reg = <0xffe00000 0x1000>;
-				clocks = <&timer_clk>, <&timer_pclk>;
-				clock-names = "timer", "pclk";
-			};
+	timer@ffe00000 {
+		compatible = "snps,dw-apb-timer";
+		interrupts = <0 170 4>;
+		reg = <0xffe00000 0x1000>;
+		clocks = <&timer_clk>, <&timer_pclk>;
+		clock-names = "timer", "pclk";
+	};

Documentation/devicetree/bindings/serial/altera_jtaguart.txt

@@ -1,4 +1,5 @@
 Altera JTAG UART
 
 Required properties:
-- compatible : should be "ALTR,juart-1.0"
+- compatible : should be "ALTR,juart-1.0" <DEPRECATED>
+- compatible : should be "altr,juart-1.0"

Documentation/devicetree/bindings/serial/altera_uart.txt

@@ -1,7 +1,8 @@
 Altera UART
 
 Required properties:
-- compatible : should be "ALTR,uart-1.0"
+- compatible : should be "ALTR,uart-1.0" <DEPRECATED>
+- compatible : should be "altr,uart-1.0"
 
 Optional properties:
 - clock-frequency : frequency of the clock input to the UART

Documentation/devicetree/bindings/serio/altera_ps2.txt

@@ -1,4 +1,5 @@
 Altera UP PS/2 controller
 
 Required properties:
-- compatible : should be "ALTR,ps2-1.0".
+- compatible : should be "ALTR,ps2-1.0". <DEPRECATED>
+- compatible : should be "altr,ps2-1.0".

Documentation/devicetree/bindings/spi/spi_altera.txt

@@ -1,4 +1,5 @@
 Altera SPI
 
 Required properties:
-- compatible : should be "ALTR,spi-1.0".
+- compatible : should be "ALTR,spi-1.0". <DEPRECATED>
+- compatible : should be "altr,spi-1.0".

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -7,6 +7,7 @@ ad	Avionic Design GmbH
 adi	Analog Devices, Inc.
 aeroflexgaisler	Aeroflex Gaisler AB
 ak	Asahi Kasei Corp.
+altr	Altera Corp.
 amcc	Applied Micro Circuits Corporation (APM, formally AMCC)
 apm	Applied Micro Circuits Corporation (APM)
 arm	ARM Ltd.

arch/arm/Makefile

@@ -190,6 +190,7 @@ machine-$(CONFIG_ARCH_S5PV210)		+= s5pv210
 machine-$(CONFIG_ARCH_SA1100)		+= sa1100
 machine-$(CONFIG_ARCH_SHARK)		+= shark
 machine-$(CONFIG_ARCH_SHMOBILE) 	+= shmobile
+machine-$(CONFIG_ARCH_SHMOBILE_MULTI) 	+= shmobile
 machine-$(CONFIG_ARCH_SIRF)		+= prima2
 machine-$(CONFIG_ARCH_SOCFPGA)		+= socfpga
 machine-$(CONFIG_ARCH_STI)		+= sti

arch/arm/boot/dts/Makefile

@@ -42,7 +42,8 @@ dtb-$(CONFIG_ARCH_AT91)	+= sama5d34ek.dtb
 dtb-$(CONFIG_ARCH_AT91)	+= sama5d35ek.dtb
 
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
-dtb-$(CONFIG_ARCH_BCM) += bcm11351-brt.dtb
+dtb-$(CONFIG_ARCH_BCM) += bcm11351-brt.dtb \
+	bcm28155-ap.dtb
 dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \
 	da850-evm.dtb
 dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \
@@ -53,13 +54,14 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos4210-trats.dtb \
 	exynos4210-universal_c210.dtb \
 	exynos4412-odroidx.dtb \
-	exynos4412-smdk4412.dtb \
 	exynos4412-origen.dtb \
+	exynos4412-smdk4412.dtb \
+	exynos4412-trats2.dtb \
 	exynos5250-arndale.dtb \
-	exynos5440-sd5v1.dtb \
 	exynos5250-smdk5250.dtb \
 	exynos5250-snow.dtb \
 	exynos5420-smdk5420.dtb \
+	exynos5440-sd5v1.dtb \
 	exynos5440-ssdk5440.dtb
 dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb \
 	ecx-2000.dtb
@@ -143,7 +145,9 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx28-cfa10037.dtb \
 	imx28-cfa10049.dtb \
 	imx28-cfa10055.dtb \
+	imx28-cfa10056.dtb \
 	imx28-cfa10057.dtb \
+	imx28-cfa10058.dtb \
 	imx28-evk.dtb \
 	imx28-m28evk.dtb \
 	imx28-sps1.dtb \
@@ -176,13 +180,14 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	am43x-epos-evm.dtb
 dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
 dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
-dtb-$(CONFIG_ARCH_U8500) += snowball.dtb \
-	hrefprev60.dtb \
-	hrefv60plus.dtb \
-	ccu8540.dtb \
-	ccu9540.dtb
+dtb-$(CONFIG_ARCH_U8500) += ste-snowball.dtb \
+	ste-hrefprev60.dtb \
+	ste-hrefv60plus.dtb \
+	ste-ccu8540.dtb \
+	ste-ccu9540.dtb
 dtb-$(CONFIG_ARCH_S3C24XX) += s3c2416-smdk2416.dtb
 dtb-$(CONFIG_ARCH_SHMOBILE) += emev2-kzm9d.dtb \
+	emev2-kzm9d-reference.dtb \
 	r8a7740-armadillo800eva.dtb \
 	r8a7778-bockw.dtb \
 	r8a7740-armadillo800eva-reference.dtb \
@@ -192,6 +197,7 @@ dtb-$(CONFIG_ARCH_SHMOBILE) += emev2-kzm9d.dtb \
 	sh73a0-kzm9g-reference.dtb \
 	r8a73a4-ape6evm.dtb \
 	sh7372-mackerel.dtb
+dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += emev2-kzm9d-reference.dtb
 dtb-$(CONFIG_ARCH_SOCFPGA) += socfpga_cyclone5.dtb \
 	socfpga_vt.dtb
 dtb-$(CONFIG_ARCH_SPEAR13XX) += spear1310-evb.dtb \
@@ -206,11 +212,14 @@ dtb-$(CONFIG_ARCH_STI)+= stih415-b2000.dtb \
 	stih415-b2020.dtb \
 	stih416-b2020.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += \
+	sun4i-a10-a1000.dtb \
 	sun4i-a10-cubieboard.dtb \
 	sun4i-a10-mini-xplus.dtb \
 	sun4i-a10-hackberry.dtb \
 	sun5i-a10s-olinuxino-micro.dtb \
-	sun5i-a13-olinuxino.dtb
+	sun5i-a13-olinuxino.dtb \
+	sun6i-a31-colombus.dtb \
+	sun7i-a20-olinuxino-micro.dtb
 dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
 	tegra20-iris-512.dtb \
 	tegra20-medcom-wide.dtb \
@@ -224,8 +233,7 @@ dtb-$(CONFIG_ARCH_TEGRA) += tegra20-harmony.dtb \
 	tegra30-beaver.dtb \
 	tegra30-cardhu-a02.dtb \
 	tegra30-cardhu-a04.dtb \
-	tegra114-dalmore.dtb \
-	tegra114-pluto.dtb
+	tegra114-dalmore.dtb
 dtb-$(CONFIG_ARCH_VERSATILE) += versatile-ab.dtb \
 	versatile-pb.dtb
 dtb-$(CONFIG_ARCH_U300) += ste-u300.dtb

arch/arm/boot/dts/at91rm9200.dtsi

@@ -120,6 +120,7 @@
 				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				pinctrl-names = "default";
 				status = "disabled";
 			};
 

arch/arm/boot/dts/at91rm9200_pqfp.dtsi

@@ -0,0 +1,17 @@
+/*
+ * at91rm9200_pqfp.dtsi - Device Tree Include file for AT91RM9200 PQFP family SoC
+ *
+ * Copyright (C) 2013 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include "at91rm9200.dtsi"
+
+/ {
+	compatible = "atmel,at91rm9200-pqfp", "atmel,at91rm9200";
+};
+
+&pioD {
+	status = "disabled";
+};

arch/arm/boot/dts/at91sam9260.dtsi

@@ -572,6 +572,7 @@
 				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				pinctrl-names = "default";
 				status = "disabled";
 			};
 

arch/arm/boot/dts/at91sam9n12.dtsi

@@ -291,6 +291,22 @@
 					};
 				};
 
+				i2c0 {
+					pinctrl_i2c0: i2c0-0 {
+						atmel,pins =
+							<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_NONE
+							 AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_NONE>;
+					};
+				};
+
+				i2c1 {
+					pinctrl_i2c1: i2c1-0 {
+						atmel,pins =
+							<AT91_PIOC 0 AT91_PERIPH_C AT91_PINCTRL_NONE
+							 AT91_PIOC 1 AT91_PERIPH_C AT91_PINCTRL_NONE>;
+					};
+				};
+
 				tcb0 {
 					pinctrl_tcb0_tclk0: tcb0_tclk0-0 {
 						atmel,pins = <AT91_PIOA 24 AT91_PERIPH_A AT91_PINCTRL_NONE>;
@@ -471,6 +487,8 @@
 				dma-names = "tx", "rx";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c0>;
 				status = "disabled";
 			};
 
@@ -483,6 +501,8 @@
 				dma-names = "tx", "rx";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1>;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/at91sam9n12ek.dts

@@ -40,6 +40,15 @@
 
 			i2c0: i2c@f8010000 {
 				status = "okay";
+
+				qt1070: keyboard@1b {
+					compatible = "qt1070";
+					reg = <0x1b>;
+					interrupt-parent = <&pioA>;
+					interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_qt1070_irq>;
+				};
 			};
 
 			i2c1: i2c@f8014000 {
@@ -66,6 +75,13 @@
 							<AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;	/* PA7 gpio CD pin pull up and deglitch */
 					};
 				};
+
+				qt1070 {
+					pinctrl_qt1070_irq: qt1070_irq {
+						atmel,pins =
+							<AT91_PIOA 2 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+					};
+				};
 			};
 
 			spi0: spi@f0000000 {
@@ -121,7 +137,7 @@
 
 		enter {
 			label = "Enter";
-			gpios = <&pioB 4 GPIO_ACTIVE_LOW>;
+			gpios = <&pioB 3 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
 			gpio-key,wakeup;
 		};

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -542,6 +542,9 @@
 				compatible = "atmel,at91sam9g45-ssc";
 				reg = <0xf0010000 0x4000>;
 				interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
+				dmas = <&dma0 1 AT91_DMA_CFG_PER_ID(13)>,
+				       <&dma0 1 AT91_DMA_CFG_PER_ID(14)>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
 				status = "disabled";

arch/arm/boot/dts/at91sam9x5ek.dtsi

@@ -59,6 +59,11 @@
 
 			i2c0: i2c@f8010000 {
 				status = "okay";
+
+				wm8731: wm8731@1a {
+					compatible = "wm8731";
+					reg = <0x1a>;
+				};
 			};
 
 			pinctrl@fffff400 {
@@ -90,6 +95,10 @@
 			watchdog@fffffe40 {
 				status = "okay";
 			};
+
+			ssc0: ssc@f0010000 {
+				status = "okay";
+			};
 		};
 
 		usb0: ohci@00600000 {
@@ -105,4 +114,19 @@
 			status = "okay";
 		};
 	};
+
+	sound {
+		compatible = "atmel,sam9x5-wm8731-audio";
+
+		atmel,model = "wm8731 @ AT91SAM9X5EK";
+
+		atmel,audio-routing =
+			"Headphone Jack", "RHPOUT",
+			"Headphone Jack", "LHPOUT",
+			"LLINEIN", "Line In Jack",
+			"RLINEIN", "Line In Jack";
+
+		atmel,ssc-controller = <&ssc0>;
+		atmel,audio-codec = <&wm8731>;
+	};
 };

arch/arm/boot/dts/bcm11351-brt.dts

@@ -17,7 +17,7 @@
 
 / {
 	model = "BCM11351 BRT board";
-	compatible = "bcm,bcm11351-brt", "bcm,bcm11351";
+	compatible = "brcm,bcm11351-brt", "brcm,bcm11351";
 
 	memory {
 		reg = <0x80000000 0x40000000>; /* 1 GB */
@@ -27,18 +27,18 @@
 		status = "okay";
 	};
 
-	sdio0: sdio@0x3f180000 {
+	sdio1: sdio@3f180000 {
 		max-frequency = <48000000>;
 		status = "okay";
 	};
 
-	sdio1: sdio@0x3f190000 {
+	sdio2: sdio@3f190000 {
 		non-removable;
 		max-frequency = <48000000>;
 		status = "okay";
 	};
 
-	sdio3: sdio@0x3f1b0000 {
+	sdio4: sdio@3f1b0000 {
 		max-frequency = <48000000>;
 		status = "okay";
 	};

arch/arm/boot/dts/bcm11351.dtsi

@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2012 Broadcom Corporation
+ * Copyright (C) 2012-2013 Broadcom Corporation
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
@@ -18,7 +18,7 @@
 
 / {
 	model = "BCM11351 SoC";
-	compatible = "bcm,bcm11351";
+	compatible = "brcm,bcm11351";
 	interrupt-parent = <&gic>;
 
 	chosen {
@@ -35,12 +35,12 @@
 	};
 
 	smc@0x3404c000 {
-		compatible = "bcm,bcm11351-smc", "bcm,kona-smc";
+		compatible = "brcm,bcm11351-smc", "brcm,kona-smc";
 		reg = <0x3404c000 0x400>; /* 1 KiB in SRAM */
 	};
 
 	uart@3e000000 {
-		compatible = "bcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
+		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
 		status = "disabled";
 		reg = <0x3e000000 0x1000>;
 		clock-frequency = <13000000>;
@@ -50,42 +50,47 @@
 	};
 
 	L2: l2-cache {
-		compatible = "bcm,bcm11351-a2-pl310-cache";
+		compatible = "brcm,bcm11351-a2-pl310-cache";
 		reg = <0x3ff20000 0x1000>;
 		cache-unified;
 		cache-level = <2>;
 	};
 
+	watchdog@35002f40 {
+		compatible = "brcm,bcm11351-wdt", "brcm,kona-wdt";
+		reg = <0x35002f40 0x6c>;
+	};
+
 	timer@35006000 {
-		compatible = "bcm,kona-timer";
+		compatible = "brcm,kona-timer";
 		reg = <0x35006000 0x1000>;
 		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 		clock-frequency = <32768>;
 	};
 
-	sdio0: sdio@0x3f180000 {
-		compatible = "bcm,kona-sdhci";
+	sdio1: sdio@3f180000 {
+		compatible = "brcm,kona-sdhci";
 		reg = <0x3f180000 0x10000>;
 		interrupts = <0x0 77 0x4>;
 		status = "disabled";
 	};
 
-	sdio1: sdio@0x3f190000 {
-		compatible = "bcm,kona-sdhci";
+	sdio2: sdio@3f190000 {
+		compatible = "brcm,kona-sdhci";
 		reg = <0x3f190000 0x10000>;
 		interrupts = <0x0 76 0x4>;
 		status = "disabled";
 	};
 
-	sdio2: sdio@0x3f1a0000 {
-		compatible = "bcm,kona-sdhci";
+	sdio3: sdio@3f1a0000 {
+		compatible = "brcm,kona-sdhci";
 		reg = <0x3f1a0000 0x10000>;
 		interrupts = <0x0 74 0x4>;
 		status = "disabled";
 	};
 
-	sdio3: sdio@0x3f1b0000 {
-		compatible = "bcm,kona-sdhci";
+	sdio4: sdio@3f1b0000 {
+		compatible = "brcm,kona-sdhci";
 		reg = <0x3f1b0000 0x10000>;
 		interrupts = <0x0 73 0x4>;
 		status = "disabled";

arch/arm/boot/dts/bcm28155-ap.dts

@@ -0,0 +1,45 @@
+/*
+ * Copyright (C) 2013 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/dts-v1/;
+
+#include "bcm11351.dtsi"
+
+/ {
+	model = "BCM28155 AP board";
+	compatible = "brcm,bcm28155-ap", "brcm,bcm11351";
+
+	memory {
+		reg = <0x80000000 0x40000000>; /* 1 GB */
+	};
+
+	uart@3e000000 {
+		status = "okay";
+	};
+
+	sdio1: sdio@3f180000 {
+		max-frequency = <48000000>;
+		status = "okay";
+	};
+
+	sdio2: sdio@3f190000 {
+		non-removable;
+		max-frequency = <48000000>;
+		status = "okay";
+	};
+
+	sdio4: sdio@3f1b0000 {
+		max-frequency = <48000000>;
+		status = "okay";
+	};
+};

arch/arm/boot/dts/ccu8540.dts

@@ -1,41 +0,0 @@
-/*
- * Copyright 2013 ST-Ericsson AB
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-/dts-v1/;
-#include "dbx5x0.dtsi"
-
-/ {
-	model = "ST-Ericsson U8540 platform with Device Tree";
-	compatible = "st-ericsson,ccu8540", "st-ericsson,u8540";
-
-	memory@0 {
-		reg = <0x20000000 0x1f000000>, <0xc0000000 0x3f000000>;
-	};
-
-	soc {
-		prcmu@80157000 {
-			reg = <0x80157000 0x2000>, <0x801b0000 0x8000>, <0x801b8000 0x3000>;
-			reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm";
-		};
-
-		uart@80120000 {
-			status = "okay";
-		};
-
-		uart@80121000 {
-			status = "okay";
-		};
-
-		uart@80007000 {
-			status = "okay";
-		};
-	};
-};

arch/arm/boot/dts/emev2-kzm9d-reference.dts

@@ -0,0 +1,57 @@
+/*
+ * Device Tree Source for the KZM9D board
+ *
+ * Copyright (C) 2013 Renesas Solutions Corp.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2.  This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+/dts-v1/;
+
+/include/ "emev2.dtsi"
+
+/ {
+	model = "EMEV2 KZM9D Board";
+	compatible = "renesas,kzm9d-reference", "renesas,emev2";
+
+	memory {
+		device_type = "memory";
+		reg = <0x40000000 0x8000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS1,115200n81 ignore_loglevel root=/dev/nfs ip=dhcp nfsroot=,rsize=4096,wsize=4096";
+	};
+
+	reg_1p8v: regulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_3p3v: regulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	lan9220@20000000 {
+		compatible = "smsc,lan9220", "smsc,lan9115";
+		reg = <0x20000000 0x10000>;
+		phy-mode = "mii";
+		interrupt-parent = <&gpio0>;
+		interrupts = <1 1>;	/* active high */
+		reg-io-width = <4>;
+		smsc,irq-active-high;
+		smsc,irq-push-pull;
+		vddvario-supply = <&reg_1p8v>;
+		vdd33a-supply = <&reg_3p3v>;
+	};
+};

arch/arm/boot/dts/emev2-kzm9d.dts

@@ -21,6 +21,6 @@
 	};
 
 	chosen {
-		bootargs = "console=tty0 console=ttyS1,115200n81 earlyprintk=serial8250-em.1,115200n81 mem=128M@0x40000000 ignore_loglevel root=/dev/nfs ip=dhcp nfsroot=,rsize=4096,wsize=4096";
+		bootargs = "console=ttyS1,115200n81 ignore_loglevel root=/dev/nfs ip=dhcp nfsroot=,rsize=4096,wsize=4096";
 	};
 };

arch/arm/boot/dts/emev2.dtsi

@@ -14,6 +14,14 @@
 	compatible = "renesas,emev2";
 	interrupt-parent = <&gic>;
 
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+		gpio3 = &gpio3;
+		gpio4 = &gpio4;
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -67,4 +75,55 @@
 		reg = <0xe1050000 0x38>;
 		interrupts = <0 11 0>;
 	};
+
+	gpio0: gpio@e0050000 {
+		compatible = "renesas,em-gio";
+		reg = <0xe0050000 0x2c>, <0xe0050040 0x20>;
+		interrupts = <0 67 0>, <0 68 0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		ngpios = <32>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+	gpio1: gpio@e0050080 {
+		compatible = "renesas,em-gio";
+		reg = <0xe0050080 0x2c>, <0xe00500c0 0x20>;
+		interrupts = <0 69 0>, <0 70 0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		ngpios = <32>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+	gpio2: gpio@e0050100 {
+		compatible = "renesas,em-gio";
+		reg = <0xe0050100 0x2c>, <0xe0050140 0x20>;
+		interrupts = <0 71 0>, <0 72 0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		ngpios = <32>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+	gpio3: gpio@e0050180 {
+		compatible = "renesas,em-gio";
+		reg = <0xe0050180 0x2c>, <0xe00501c0 0x20>;
+		interrupts = <0 73 0>, <0 74 0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		ngpios = <32>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+	gpio4: gpio@e0050200 {
+		compatible = "renesas,em-gio";
+		reg = <0xe0050200 0x2c>, <0xe0050240 0x20>;
+		interrupts = <0 75 0>, <0 76 0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		ngpios = <31>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
 };

arch/arm/boot/dts/exynos4.dtsi

@@ -36,6 +36,12 @@
 		i2c5 = &i2c_5;
 		i2c6 = &i2c_6;
 		i2c7 = &i2c_7;
+		csis0 = &csis_0;
+		csis1 = &csis_1;
+		fimc0 = &fimc_0;
+		fimc1 = &fimc_1;
+		fimc2 = &fimc_2;
+		fimc3 = &fimc_3;
 	};
 
 	chipid@10000000 {
@@ -92,6 +98,88 @@
 		reg = <0x10010000 0x400>;
 	};
 
+	camera {
+		compatible = "samsung,fimc", "simple-bus";
+		status = "disabled";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		clock_cam: clock-controller {
+			 #clock-cells = <1>;
+		};
+
+		fimc_0: fimc@11800000 {
+			compatible = "samsung,exynos4210-fimc";
+			reg = <0x11800000 0x1000>;
+			interrupts = <0 84 0>;
+			clocks = <&clock 256>, <&clock 128>;
+			clock-names = "fimc", "sclk_fimc";
+			samsung,power-domain = <&pd_cam>;
+			samsung,sysreg = <&sys_reg>;
+			status = "disabled";
+		};
+
+		fimc_1: fimc@11810000 {
+			compatible = "samsung,exynos4210-fimc";
+			reg = <0x11810000 0x1000>;
+			interrupts = <0 85 0>;
+			clocks = <&clock 257>, <&clock 129>;
+			clock-names = "fimc", "sclk_fimc";
+			samsung,power-domain = <&pd_cam>;
+			samsung,sysreg = <&sys_reg>;
+			status = "disabled";
+		};
+
+		fimc_2: fimc@11820000 {
+			compatible = "samsung,exynos4210-fimc";
+			reg = <0x11820000 0x1000>;
+			interrupts = <0 86 0>;
+			clocks = <&clock 258>, <&clock 130>;
+			clock-names = "fimc", "sclk_fimc";
+			samsung,power-domain = <&pd_cam>;
+			samsung,sysreg = <&sys_reg>;
+			status = "disabled";
+		};
+
+		fimc_3: fimc@11830000 {
+			compatible = "samsung,exynos4210-fimc";
+			reg = <0x11830000 0x1000>;
+			interrupts = <0 87 0>;
+			clocks = <&clock 259>, <&clock 131>;
+			clock-names = "fimc", "sclk_fimc";
+			samsung,power-domain = <&pd_cam>;
+			samsung,sysreg = <&sys_reg>;
+			status = "disabled";
+		};
+
+		csis_0: csis@11880000 {
+			compatible = "samsung,exynos4210-csis";
+			reg = <0x11880000 0x4000>;
+			interrupts = <0 78 0>;
+			clocks = <&clock 260>, <&clock 134>;
+			clock-names = "csis", "sclk_csis";
+			bus-width = <4>;
+			samsung,power-domain = <&pd_cam>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		csis_1: csis@11890000 {
+			compatible = "samsung,exynos4210-csis";
+			reg = <0x11890000 0x4000>;
+			interrupts = <0 80 0>;
+			clocks = <&clock 261>, <&clock 135>;
+			clock-names = "csis", "sclk_csis";
+			bus-width = <2>;
+			samsung,power-domain = <&pd_cam>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
 	watchdog@10060000 {
 		compatible = "samsung,s3c2410-wdt";
 		reg = <0x10060000 0x100>;
@@ -155,13 +243,31 @@
 		status = "disabled";
 	};
 
+	ehci@12580000 {
+		compatible = "samsung,exynos4210-ehci";
+		reg = <0x12580000 0x100>;
+		interrupts = <0 70 0>;
+		clocks = <&clock 304>;
+		clock-names = "usbhost";
+		status = "disabled";
+	};
+
+	ohci@12590000 {
+		compatible = "samsung,exynos4210-ohci";
+		reg = <0x12590000 0x100>;
+		interrupts = <0 70 0>;
+		clocks = <&clock 304>;
+		clock-names = "usbhost";
+		status = "disabled";
+	};
+
 	mfc: codec@13400000 {
 		compatible = "samsung,mfc-v5";
 		reg = <0x13400000 0x10000>;
 		interrupts = <0 94 0>;
 		samsung,power-domain = <&pd_mfc>;
-		clocks = <&clock 170>, <&clock 273>;
-		clock-names = "sclk_mfc", "mfc";
+		clocks = <&clock 273>;
+		clock-names = "mfc";
 		status = "disabled";
 	};
 
@@ -297,8 +403,8 @@
 		compatible = "samsung,exynos4210-spi";
 		reg = <0x13920000 0x100>;
 		interrupts = <0 66 0>;
-		tx-dma-channel = <&pdma0 7>; /* preliminary */
-		rx-dma-channel = <&pdma0 6>; /* preliminary */
+		dmas = <&pdma0 7>, <&pdma0 6>;
+		dma-names = "tx", "rx";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		clocks = <&clock 327>, <&clock 159>;
@@ -312,8 +418,8 @@
 		compatible = "samsung,exynos4210-spi";
 		reg = <0x13930000 0x100>;
 		interrupts = <0 67 0>;
-		tx-dma-channel = <&pdma1 7>; /* preliminary */
-		rx-dma-channel = <&pdma1 6>; /* preliminary */
+		dmas = <&pdma1 7>, <&pdma1 6>;
+		dma-names = "tx", "rx";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		clocks = <&clock 328>, <&clock 160>;
@@ -327,8 +433,8 @@
 		compatible = "samsung,exynos4210-spi";
 		reg = <0x13940000 0x100>;
 		interrupts = <0 68 0>;
-		tx-dma-channel = <&pdma0 9>; /* preliminary */
-		rx-dma-channel = <&pdma0 8>; /* preliminary */
+		dmas = <&pdma0 9>, <&pdma0 8>;
+		dma-names = "tx", "rx";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		clocks = <&clock 329>, <&clock 161>;

arch/arm/boot/dts/exynos4210-pinctrl.dtsi

@@ -797,6 +797,29 @@
 			samsung,pin-pud = <0>;
 			samsung,pin-drv = <0>;
 		};
+
+		cam_port_a_io: cam-port-a-io {
+			samsung,pins = "gpj0-0", "gpj0-1", "gpj0-2", "gpj0-3",
+					"gpj0-4", "gpj0-5", "gpj0-6", "gpj0-7",
+					"gpj1-0", "gpj1-1", "gpj1-2", "gpj1-4";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		cam_port_a_clk_active: cam-port-a-clk-active {
+			samsung,pins = "gpj1-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <3>;
+		};
+
+		cam_port_a_clk_idle: cam-port-a-clk-idle {
+			samsung,pins = "gpj1-3";
+			samsung,pin-function = <0>;
+			samsung,pin-pud = <1>;
+			samsung,pin-drv = <0>;
+		};
 	};
 
 	pinctrl@03860000 {

arch/arm/boot/dts/exynos4210-trats.dts

@@ -30,13 +30,62 @@
 		bootargs = "console=ttySAC2,115200N8 root=/dev/mmcblk0p5 rootwait earlyprintk panic=5";
 	};
 
-	vemmc_reg: voltage-regulator@0 {
-	        compatible = "regulator-fixed";
-		regulator-name = "VMEM_VDD_2.8V";
-		regulator-min-microvolt = <2800000>;
-		regulator-max-microvolt = <2800000>;
-		gpio = <&gpk0 2 0>;
-		enable-active-high;
+	regulators {
+		compatible = "simple-bus";
+
+		vemmc_reg: regulator-0 {
+			compatible = "regulator-fixed";
+			regulator-name = "VMEM_VDD_2.8V";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			gpio = <&gpk0 2 0>;
+			enable-active-high;
+		};
+
+		tsp_reg: regulator-1 {
+			compatible = "regulator-fixed";
+			regulator-name = "TSP_FIXED_VOLTAGES";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			gpio = <&gpl0 3 0>;
+			enable-active-high;
+		};
+
+		cam_af_28v_reg: regulator-2 {
+			compatible = "regulator-fixed";
+			regulator-name = "8M_AF_2.8V_EN";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			gpio = <&gpk1 1 0>;
+			enable-active-high;
+		};
+
+		cam_io_en_reg: regulator-3 {
+			compatible = "regulator-fixed";
+			regulator-name = "CAM_IO_EN";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			gpio = <&gpe2 1 0>;
+			enable-active-high;
+		};
+
+		cam_io_12v_reg: regulator-4 {
+			compatible = "regulator-fixed";
+			regulator-name = "8M_1.2V_EN";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			gpio = <&gpe2 5 0>;
+			enable-active-high;
+		};
+
+		vt_core_15v_reg: regulator-5 {
+			compatible = "regulator-fixed";
+			regulator-name = "VT_CORE_1.5V";
+			regulator-min-microvolt = <1500000>;
+			regulator-max-microvolt = <1500000>;
+			gpio = <&gpe2 2 0>;
+			enable-active-high;
+		};
 	};
 
 	sdhci_emmc: sdhci@12510000 {
@@ -97,15 +146,6 @@
 		};
 	};
 
-	tsp_reg: voltage-regulator {
-		compatible = "regulator-fixed";
-		regulator-name = "TSP_FIXED_VOLTAGES";
-		regulator-min-microvolt = <2800000>;
-		regulator-max-microvolt = <2800000>;
-		gpio = <&gpl0 3 0>;
-		enable-active-high;
-	};
-
 	i2c@13890000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-slave-addr = <0x10>;
@@ -218,6 +258,12 @@
 				     regulator-always-on;
 				};
 
+				vtcam_reg: LDO12 {
+				     regulator-name = "VT_CAM_1.8V";
+				     regulator-min-microvolt = <1800000>;
+				     regulator-max-microvolt = <1800000>;
+				};
+
 				vcclcd_reg: LDO13 {
 				     regulator-name = "VCC_3.3V_LCD";
 				     regulator-min-microvolt = <3300000>;
@@ -301,4 +347,26 @@
 			clock-frequency = <24000000>;
 		};
 	};
+
+	camera {
+		pinctrl-names = "default";
+		pinctrl-0 = <>;
+		status = "okay";
+
+		fimc_0: fimc@11800000 {
+			status = "okay";
+		};
+
+		fimc_1: fimc@11810000 {
+			status = "okay";
+		};
+
+		fimc_2: fimc@11820000 {
+			status = "okay";
+		};
+
+		fimc_3: fimc@11830000 {
+			status = "okay";
+		};
+	};
 };

arch/arm/boot/dts/exynos4210.dtsi

@@ -125,4 +125,34 @@
 		clock-names = "sclk_fimg2d", "fimg2d";
 		status = "disabled";
 	};
+
+	camera {
+		clocks = <&clock 132>, <&clock 133>, <&clock 351>, <&clock 352>;
+		clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", "pxl_async1";
+
+		fimc_0: fimc@11800000 {
+			samsung,pix-limits = <4224 8192 1920 4224>;
+			samsung,mainscaler-ext;
+			samsung,cam-if;
+		};
+
+		fimc_1: fimc@11810000 {
+			samsung,pix-limits = <4224 8192 1920 4224>;
+			samsung,mainscaler-ext;
+			samsung,cam-if;
+		};
+
+		fimc_2: fimc@11820000 {
+			samsung,pix-limits = <4224 8192 1920 4224>;
+			samsung,mainscaler-ext;
+			samsung,lcd-wb;
+		};
+
+		fimc_3: fimc@11830000 {
+			samsung,pix-limits = <1920 8192 1366 1920>;
+			samsung,rotators = <0>;
+			samsung,mainscaler-ext;
+			samsung,lcd-wb;
+		};
+	};
 };

arch/arm/boot/dts/exynos4412-origen.dts

@@ -27,6 +27,11 @@
 		bootargs ="console=ttySAC2,115200";
 	};
 
+	firmware@0203F000 {
+		compatible = "samsung,secure-firmware";
+		reg = <0x0203F000 0x1000>;
+	};
+
 	mmc_reg: voltage-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "VMEM_VDD_2.8V";

arch/arm/boot/dts/exynos4412-trats2.dts

@@ -0,0 +1,579 @@
+/*
+ * Samsung's Exynos4412 based Trats 2 board device tree source
+ *
+ * Copyright (c) 2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Device tree source file for Samsung's Trats 2 board which is based on
+ * Samsung's Exynos4412 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/dts-v1/;
+#include "exynos4412.dtsi"
+
+/ {
+	model = "Samsung Trats 2 based on Exynos4412";
+	compatible = "samsung,trats2", "samsung,exynos4412";
+
+	aliases {
+		i2c8 = &i2c_ak8975;
+	};
+
+	memory {
+		reg =  <0x40000000 0x40000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttySAC2,115200N8 root=/dev/mmcblk0p5 rootwait earlyprintk panic=5";
+	};
+
+	firmware@0204F000 {
+		compatible = "samsung,secure-firmware";
+		reg = <0x0204F000 0x1000>;
+	};
+
+	fixed-rate-clocks {
+		xxti {
+			compatible = "samsung,clock-xxti", "fixed-clock";
+			clock-frequency = <0>;
+		};
+
+		xusbxti {
+			compatible = "samsung,clock-xusbxti", "fixed-clock";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vemmc_reg: regulator-0 {
+			compatible = "regulator-fixed";
+			regulator-name = "VMEM_VDD_2.8V";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			gpio = <&gpk0 2 0>;
+			enable-active-high;
+		};
+
+		cam_io_reg: voltage-regulator-1 {
+			compatible = "regulator-fixed";
+			regulator-name = "CAM_SENSOR_A";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			gpio = <&gpm0 2 0>;
+			enable-active-high;
+		};
+
+		/* More to come */
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-down {
+			interrupt-parent = <&gpj1>;
+			interrupts = <2 0>;
+			gpios = <&gpj1 2 1>;
+			linux,code = <114>;
+			label = "volume down";
+			debounce-interval = <10>;
+		};
+
+		key-up {
+			interrupt-parent = <&gpj1>;
+			interrupts = <1 0>;
+			gpios = <&gpj1 1 1>;
+			linux,code = <115>;
+			label = "volume up";
+			debounce-interval = <10>;
+		};
+
+		key-power {
+			interrupt-parent = <&gpx2>;
+			interrupts = <7 0>;
+			gpios = <&gpx2 7 1>;
+			linux,code = <116>;
+			label = "power";
+			debounce-interval = <10>;
+			gpio-key,wakeup;
+		};
+	};
+
+	i2c@13890000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-slave-addr = <0x10>;
+		samsung,i2c-max-bus-freq = <400000>;
+		pinctrl-0 = <&i2c3_bus>;
+		pinctrl-names = "default";
+		status = "okay";
+
+		mms114-touchscreen@48 {
+			compatible = "melfas,mms114";
+			reg = <0x48>;
+			interrupt-parent = <&gpm2>;
+			interrupts = <3 2>;
+			x-size = <720>;
+			y-size = <1280>;
+			avdd-supply = <&ldo23_reg>;
+			vdd-supply = <&ldo24_reg>;
+		};
+	};
+
+	i2c@138D0000 {
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-slave-addr = <0x10>;
+		samsung,i2c-max-bus-freq = <100000>;
+		pinctrl-0 = <&i2c7_bus>;
+		pinctrl-names = "default";
+		status = "okay";
+
+		max77686_pmic@09 {
+			compatible = "maxim,max77686";
+			interrupt-parent = <&gpx0>;
+			interrupts = <7 0>;
+			reg = <0x09>;
+
+			voltage-regulators {
+				ldo1_reg: ldo1 {
+					regulator-compatible = "LDO1";
+					regulator-name = "VALIVE_1.0V_AP";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					regulator-mem-on;
+				};
+
+				ldo2_reg: ldo2 {
+					regulator-compatible = "LDO2";
+					regulator-name = "VM1M2_1.2V_AP";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-mem-on;
+				};
+
+				ldo3_reg: ldo3 {
+					regulator-compatible = "LDO3";
+					regulator-name = "VCC_1.8V_AP";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-mem-on;
+				};
+
+				ldo4_reg: ldo4 {
+					regulator-compatible = "LDO4";
+					regulator-name = "VCC_2.8V_AP";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+					regulator-mem-on;
+				};
+
+				ldo5_reg: ldo5 {
+					regulator-compatible = "LDO5";
+					regulator-name = "VCC_1.8V_IO";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-mem-on;
+				};
+
+				ldo6_reg: ldo6 {
+					regulator-compatible = "LDO6";
+					regulator-name = "VMPLL_1.0V_AP";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					regulator-mem-on;
+				};
+
+				ldo7_reg: ldo7 {
+					regulator-compatible = "LDO7";
+					regulator-name = "VPLL_1.0V_AP";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					regulator-mem-on;
+				};
+
+				ldo8_reg: ldo8 {
+					regulator-compatible = "LDO8";
+					regulator-name = "VMIPI_1.0V";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-mem-off;
+				};
+
+				ldo9_reg: ldo9 {
+					regulator-compatible = "LDO9";
+					regulator-name = "CAM_ISP_MIPI_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-mem-idle;
+				};
+
+				ldo10_reg: ldo10 {
+					regulator-compatible = "LDO10";
+					regulator-name = "VMIPI_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-mem-off;
+				};
+
+				ldo11_reg: ldo11 {
+					regulator-compatible = "LDO11";
+					regulator-name = "VABB1_1.95V";
+					regulator-min-microvolt = <1950000>;
+					regulator-max-microvolt = <1950000>;
+					regulator-always-on;
+					regulator-mem-off;
+				};
+
+				ldo12_reg: ldo12 {
+					regulator-compatible = "LDO12";
+					regulator-name = "VUOTG_3.0V";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-mem-off;
+				};
+
+				ldo13_reg: ldo13 {
+					regulator-compatible = "LDO13";
+					regulator-name = "NFC_AVDD_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-mem-idle;
+				};
+
+				ldo14_reg: ldo14 {
+					regulator-compatible = "LDO14";
+					regulator-name = "VABB2_1.95V";
+					regulator-min-microvolt = <1950000>;
+					regulator-max-microvolt = <1950000>;
+					regulator-always-on;
+					regulator-mem-off;
+				};
+
+				ldo15_reg: ldo15 {
+					regulator-compatible = "LDO15";
+					regulator-name = "VHSIC_1.0V";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-mem-off;
+				};
+
+				ldo16_reg: ldo16 {
+					regulator-compatible = "LDO16";
+					regulator-name = "VHSIC_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-mem-off;
+				};
+
+				ldo17_reg: ldo17 {
+					regulator-compatible = "LDO17";
+					regulator-name = "CAM_SENSOR_CORE_1.2V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-mem-idle;
+				};
+
+				ldo18_reg: ldo18 {
+					regulator-compatible = "LDO18";
+					regulator-name = "CAM_ISP_SEN_IO_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-mem-idle;
+				};
+
+				ldo19_reg: ldo19 {
+					regulator-compatible = "LDO19";
+					regulator-name = "VT_CAM_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-mem-idle;
+				};
+
+				ldo20_reg: ldo20 {
+					regulator-compatible = "LDO20";
+					regulator-name = "VDDQ_PRE_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-mem-idle;
+				};
+
+				ldo21_reg: ldo21 {
+					regulator-compatible = "LDO21";
+					regulator-name = "VTF_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-mem-idle;
+				};
+
+				ldo22_reg: ldo22 {
+					regulator-compatible = "LDO22";
+					regulator-name = "VMEM_VDD_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+					regulator-mem-off;
+				};
+
+				ldo23_reg: ldo23 {
+					regulator-compatible = "LDO23";
+					regulator-name = "TSP_AVDD_3.3V";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-mem-idle;
+				};
+
+				ldo24_reg: ldo24 {
+					regulator-compatible = "LDO24";
+					regulator-name = "TSP_VDD_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-mem-idle;
+				};
+
+				ldo25_reg: ldo25 {
+					regulator-compatible = "LDO25";
+					regulator-name = "LCD_VCC_3.3V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-mem-idle;
+				};
+
+				ldo26_reg: ldo26 {
+					regulator-compatible = "LDO26";
+					regulator-name = "MOTOR_VCC_3.0V";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-mem-idle;
+				};
+
+				buck1_reg: buck1 {
+					regulator-compatible = "BUCK1";
+					regulator-name = "vdd_mif";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+					regulator-boot-on;
+					regulator-mem-off;
+				};
+
+				buck2_reg: buck2 {
+					regulator-compatible = "BUCK2";
+					regulator-name = "vdd_arm";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1500000>;
+					regulator-always-on;
+					regulator-boot-on;
+					regulator-mem-off;
+				};
+
+				buck3_reg: buck3 {
+					regulator-compatible = "BUCK3";
+					regulator-name = "vdd_int";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1150000>;
+					regulator-always-on;
+					regulator-boot-on;
+					regulator-mem-off;
+				};
+
+				buck4_reg: buck4 {
+					regulator-compatible = "BUCK4";
+					regulator-name = "vdd_g3d";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1150000>;
+					regulator-boot-on;
+					regulator-mem-off;
+				};
+
+				buck5_reg: buck5 {
+					regulator-compatible = "BUCK5";
+					regulator-name = "VMEM_1.2V_AP";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				buck6_reg: buck6 {
+					regulator-compatible = "BUCK6";
+					regulator-name = "VCC_SUB_1.35V";
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-always-on;
+				};
+
+				buck7_reg: buck7 {
+					regulator-compatible = "BUCK7";
+					regulator-name = "VCC_SUB_2.0V";
+					regulator-min-microvolt = <2000000>;
+					regulator-max-microvolt = <2000000>;
+					regulator-always-on;
+				};
+
+				buck8_reg: buck8 {
+					regulator-compatible = "BUCK8";
+					regulator-name = "VMEM_VDDF_3.0V";
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					regulator-always-on;
+					regulator-mem-off;
+				};
+
+				buck9_reg: buck9 {
+					regulator-compatible = "BUCK9";
+					regulator-name = "CAM_ISP_CORE_1.2V";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-mem-off;
+				};
+			};
+		};
+	};
+
+	sdhci@12510000 {
+		bus-width = <8>;
+		non-removable;
+		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus8>;
+		pinctrl-names = "default";
+		vmmc-supply = <&vemmc_reg>;
+		status = "okay";
+	};
+
+	serial@13800000 {
+		status = "okay";
+	};
+
+	serial@13810000 {
+		status = "okay";
+	};
+
+	serial@13820000 {
+		status = "okay";
+	};
+
+	serial@13830000 {
+		status = "okay";
+	};
+
+	i2c_ak8975: i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		gpios = <&gpy2 4 0>, <&gpy2 5 0>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		ak8975@0c {
+			compatible = "ak,ak8975";
+			reg = <0x0c>;
+			gpios = <&gpj0 7 0>;
+		};
+	};
+
+	spi_1: spi@13930000 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi1_bus>;
+		status = "okay";
+
+		s5c73m3_spi: s5c73m3 {
+			compatible = "samsung,s5c73m3";
+			spi-max-frequency = <50000000>;
+			reg = <0>;
+			controller-data {
+				cs-gpio = <&gpb 5 0>;
+				samsung,spi-feedback-delay = <2>;
+			};
+		};
+	};
+
+	camera {
+		pinctrl-0 = <&cam_port_b_clk_active>;
+		pinctrl-names = "default";
+		status = "okay";
+
+		fimc_0: fimc@11800000 {
+			status = "okay";
+		};
+
+		fimc_1: fimc@11810000 {
+			status = "okay";
+		};
+
+		fimc_2: fimc@11820000 {
+			status = "okay";
+		};
+
+		fimc_3: fimc@11830000 {
+			status = "okay";
+		};
+
+		csis_1: csis@11890000 {
+			vddcore-supply = <&ldo8_reg>;
+			vddio-supply = <&ldo10_reg>;
+			clock-frequency = <160000000>;
+			status = "okay";
+
+			/* Camera D (4) MIPI CSI-2 (CSIS1) */
+			port@4 {
+				reg = <4>;
+				csis1_ep: endpoint {
+					remote-endpoint = <&is_s5k6a3_ep>;
+					data-lanes = <1>;
+					samsung,csis-hs-settle = <18>;
+					samsung,csis-wclk;
+				};
+			};
+		};
+
+		fimc_lite_0: fimc-lite@12390000 {
+			status = "okay";
+		};
+
+		fimc_lite_1: fimc-lite@123A0000 {
+			status = "okay";
+		};
+
+		fimc-is@12000000 {
+			pinctrl-0 = <&fimc_is_uart>;
+			pinctrl-names = "default";
+			status = "okay";
+
+			i2c1_isp: i2c-isp@12140000 {
+				pinctrl-0 = <&fimc_is_i2c1>;
+				pinctrl-names = "default";
+
+				s5k6a3@10 {
+					compatible = "samsung,s5k6a3";
+					reg = <0x10>;
+					svdda-supply = <&cam_io_reg>;
+					svddio-supply = <&ldo19_reg>;
+					clock-frequency = <24000000>;
+					/* CAM_B_CLKOUT */
+					clocks = <&clock_cam 1>;
+					clock-names = "mclk";
+					samsung,camclk-out = <1>;
+					gpios = <&gpm1 6 0>;
+
+					port {
+						is_s5k6a3_ep: endpoint {
+							remote-endpoint = <&csis1_ep>;
+							data-lanes = <1>;
+						};
+					};
+				};
+			};
+		};
+	};
+};

arch/arm/boot/dts/exynos4x12-pinctrl.dtsi

@@ -401,13 +401,26 @@
 			samsung,pin-drv = <0>;
 		};
 
-		cam_port_a: cam-port-a {
+		cam_port_a_io: cam-port-a-io {
 			samsung,pins = "gpj0-0", "gpj0-1", "gpj0-2", "gpj0-3",
 					"gpj0-4", "gpj0-5", "gpj0-6", "gpj0-7",
-					"gpj1-0", "gpj1-1", "gpj1-2", "gpj1-3",
-					"gpj1-4";
+					"gpj1-0", "gpj1-1", "gpj1-2", "gpj1-4";
 			samsung,pin-function = <2>;
-			samsung,pin-pud = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		cam_port_a_clk_active: cam-port-a-clk-active {
+			samsung,pins = "gpj1-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <3>;
+		};
+
+		cam_port_a_clk_idle: cam-port-a-clk-idle {
+			samsung,pins = "gpj1-3";
+			samsung,pin-function = <0>;
+			samsung,pin-pud = <1>;
 			samsung,pin-drv = <0>;
 		};
 	};
@@ -778,16 +791,29 @@
 			samsung,pin-drv = <3>;
 		};
 
-		cam_port_b: cam-port-b {
+		cam_port_b_io: cam-port-b-io {
 			samsung,pins = "gpm0-0", "gpm0-1", "gpm0-2", "gpm0-3",
 					"gpm0-4", "gpm0-5", "gpm0-6", "gpm0-7",
-					"gpm1-0", "gpm1-1", "gpm2-0", "gpm2-1",
-					"gpm2-2";
+					"gpm1-0", "gpm1-1", "gpm2-0", "gpm2-1";
 			samsung,pin-function = <3>;
 			samsung,pin-pud = <3>;
 			samsung,pin-drv = <0>;
 		};
 
+		cam_port_b_clk_active: cam-port-b-clk-active {
+			samsung,pins = "gpm2-2";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <3>;
+		};
+
+		cam_port_b_clk_idle: cam-port-b-clk-idle {
+			samsung,pins = "gpm2-2";
+			samsung,pin-function = <0>;
+			samsung,pin-pud = <1>;
+			samsung,pin-drv = <0>;
+		};
+
 		eint0: ext-int0 {
 			samsung,pins = "gpx0-0";
 			samsung,pin-function = <0xf>;
@@ -822,6 +848,27 @@
 			samsung,pin-pud = <0>;
 			samsung,pin-drv = <0>;
 		};
+
+		fimc_is_i2c0: fimc-is-i2c0 {
+			samsung,pins = "gpm4-0", "gpm4-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		fimc_is_i2c1: fimc-is-i2c1 {
+			samsung,pins = "gpm4-2", "gpm4-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		fimc_is_uart: fimc-is-uart {
+			samsung,pins = "gpm3-5", "gpm3-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
 	};
 
 	pinctrl@03860000 {

arch/arm/boot/dts/exynos4x12.dtsi

@@ -26,6 +26,13 @@
 		pinctrl1 = &pinctrl_1;
 		pinctrl2 = &pinctrl_2;
 		pinctrl3 = &pinctrl_3;
+		fimc-lite0 = &fimc_lite_0;
+		fimc-lite1 = &fimc_lite_1;
+	};
+
+	pd_isp: isp-power-domain@10023CA0 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10023CA0 0x20>;
 	};
 
 	clock: clock-controller@10030000 {
@@ -73,4 +80,100 @@
 		clock-names = "sclk_fimg2d", "fimg2d";
 		status = "disabled";
 	};
+
+	camera {
+		clocks = <&clock 132>, <&clock 133>, <&clock 351>, <&clock 352>;
+		clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", "pxl_async1";
+
+		fimc_0: fimc@11800000 {
+			compatible = "samsung,exynos4212-fimc";
+			samsung,pix-limits = <4224 8192 1920 4224>;
+			samsung,mainscaler-ext;
+			samsung,isp-wb;
+			samsung,cam-if;
+		};
+
+		fimc_1: fimc@11810000 {
+			compatible = "samsung,exynos4212-fimc";
+			samsung,pix-limits = <4224 8192 1920 4224>;
+			samsung,mainscaler-ext;
+			samsung,isp-wb;
+			samsung,cam-if;
+		};
+
+		fimc_2: fimc@11820000 {
+			compatible = "samsung,exynos4212-fimc";
+			samsung,pix-limits = <4224 8192 1920 4224>;
+			samsung,mainscaler-ext;
+			samsung,isp-wb;
+			samsung,lcd-wb;
+			samsung,cam-if;
+		};
+
+		fimc_3: fimc@11830000 {
+			compatible = "samsung,exynos4212-fimc";
+			samsung,pix-limits = <1920 8192 1366 1920>;
+			samsung,rotators = <0>;
+			samsung,mainscaler-ext;
+			samsung,isp-wb;
+			samsung,lcd-wb;
+		};
+
+		fimc_lite_0: fimc-lite@12390000 {
+			compatible = "samsung,exynos4212-fimc-lite";
+			reg = <0x12390000 0x1000>;
+			interrupts = <0 105 0>;
+			samsung,power-domain = <&pd_isp>;
+			clocks = <&clock 353>;
+			clock-names = "flite";
+			status = "disabled";
+		};
+
+		fimc_lite_1: fimc-lite@123A0000 {
+			compatible = "samsung,exynos4212-fimc-lite";
+			reg = <0x123A0000 0x1000>;
+			interrupts = <0 106 0>;
+			samsung,power-domain = <&pd_isp>;
+			clocks = <&clock 354>;
+			clock-names = "flite";
+			status = "disabled";
+		};
+
+		fimc_is: fimc-is@12000000 {
+			compatible = "samsung,exynos4212-fimc-is", "simple-bus";
+			reg = <0x12000000 0x260000>;
+			interrupts = <0 90 0>, <0 95 0>;
+			samsung,power-domain = <&pd_isp>;
+			clocks = <&clock 353>, <&clock 354>, <&clock 355>,
+				<&clock 356>, <&clock 17>, <&clock 357>,
+				<&clock 358>, <&clock 359>, <&clock 360>,
+				<&clock 450>,<&clock 451>, <&clock 452>,
+				<&clock 453>, <&clock 176>, <&clock 13>,
+				<&clock 454>, <&clock 395>, <&clock 455>;
+			clock-names = "lite0", "lite1", "ppmuispx",
+				      "ppmuispmx", "mpll", "isp",
+				      "drc", "fd", "mcuisp",
+				      "ispdiv0", "ispdiv1", "mcuispdiv0",
+				      "mcuispdiv1", "uart", "aclk200",
+				      "div_aclk200", "aclk400mcuisp",
+				      "div_aclk400mcuisp";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			status = "disabled";
+
+			pmu {
+				reg = <0x10020000 0x3000>;
+			};
+
+			i2c1_isp: i2c-isp@12140000 {
+				compatible = "samsung,exynos4212-i2c-isp";
+				reg = <0x12140000 0x100>;
+				clocks = <&clock 370>;
+				clock-names = "i2c_isp";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
 };

arch/arm/boot/dts/exynos5.dtsi

@@ -108,4 +108,23 @@
 		interrupts = <0 42 0>;
 		status = "disabled";
 	};
+
+	fimd@14400000 {
+		compatible = "samsung,exynos5250-fimd";
+		interrupt-parent = <&combiner>;
+		reg = <0x14400000 0x40000>;
+		interrupt-names = "fifo", "vsync", "lcd_sys";
+		interrupts = <18 4>, <18 5>, <18 6>;
+		status = "disabled";
+	};
+
+	dp-controller@145B0000 {
+		compatible = "samsung,exynos5-dp";
+		reg = <0x145B0000 0x1000>;
+		interrupts = <10 3>;
+		interrupt-parent = <&combiner>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
 };

arch/arm/boot/dts/exynos5250-arndale.dts

@@ -11,6 +11,7 @@
 
 /dts-v1/;
 #include "exynos5250.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "Insignal Arndale evaluation board based on EXYNOS5250";
@@ -37,6 +38,28 @@
 		s5m8767_pmic@66 {
 			compatible = "samsung,s5m8767-pmic";
 			reg = <0x66>;
+			interrupt-parent = <&gpx3>;
+			interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+
+			vinb1-supply = <&main_dc_reg>;
+			vinb2-supply = <&main_dc_reg>;
+			vinb3-supply = <&main_dc_reg>;
+			vinb4-supply = <&main_dc_reg>;
+			vinb5-supply = <&main_dc_reg>;
+			vinb6-supply = <&main_dc_reg>;
+			vinb7-supply = <&main_dc_reg>;
+			vinb8-supply = <&main_dc_reg>;
+			vinb9-supply = <&main_dc_reg>;
+
+			vinl1-supply = <&buck7_reg>;
+			vinl2-supply = <&buck7_reg>;
+			vinl3-supply = <&buck7_reg>;
+			vinl4-supply = <&main_dc_reg>;
+			vinl5-supply = <&main_dc_reg>;
+			vinl6-supply = <&main_dc_reg>;
+			vinl7-supply = <&main_dc_reg>;
+			vinl8-supply = <&buck8_reg>;
+			vinl9-supply = <&buck8_reg>;
 
 			s5m8767,pmic-buck2-dvs-voltage = <1300000>;
 			s5m8767,pmic-buck3-dvs-voltage = <1100000>;
@@ -276,6 +299,16 @@
 					op_mode = <1>;
 				};
 
+				buck7_reg: BUCK7 {
+					regulator-name = "PVDD_BUCK7";
+					regulator-always-on;
+				};
+
+				buck8_reg: BUCK8 {
+					regulator-name = "PVDD_BUCK8";
+					regulator-always-on;
+				};
+
 				buck9_reg: BUCK9 {
 					regulator-name = "VDD_33_OFF_EXT1";
 					regulator-min-microvolt = <750000>;
@@ -295,7 +328,22 @@
 	};
 
 	i2c@12C90000 {
-		status = "disabled";
+		wm1811a@1a {
+			compatible = "wlf,wm1811";
+			reg = <0x1a>;
+
+			AVDD2-supply = <&main_dc_reg>;
+			CPVDD-supply = <&main_dc_reg>;
+			DBVDD1-supply = <&main_dc_reg>;
+			DBVDD2-supply = <&main_dc_reg>;
+			DBVDD3-supply = <&main_dc_reg>;
+			LDO1VDD-supply = <&main_dc_reg>;
+			SPKVDD1-supply = <&main_dc_reg>;
+			SPKVDD2-supply = <&main_dc_reg>;
+
+			wlf,ldo1ena = <&gpb0 0 0>;
+			wlf,ldo2ena = <&gpb0 1 0>;
+		};
 	};
 
 	i2c@12CA0000 {
@@ -429,18 +477,29 @@
 		vdd-supply = <&ldo8_reg>;
 	};
 
-	mmc_reg: voltage-regulator {
-		compatible = "regulator-fixed";
-		regulator-name = "VDD_33ON_2.8V";
-		regulator-min-microvolt = <2800000>;
-		regulator-max-microvolt = <2800000>;
-		gpio = <&gpx1 1 1>;
-		enable-active-high;
-	};
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-	reg_hdmi_en: fixedregulator@0 {
-		compatible = "regulator-fixed";
-		regulator-name = "hdmi-en";
+		main_dc_reg: fixedregulator@1 {
+			compatible = "regulator-fixed";
+			regulator-name = "MAIN_DC";
+		};
+
+		mmc_reg: voltage-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "VDD_33ON_2.8V";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			gpio = <&gpx1 1 1>;
+			enable-active-high;
+		};
+
+		reg_hdmi_en: fixedregulator@0 {
+			compatible = "regulator-fixed";
+			regulator-name = "hdmi-en";
+		};
 	};
 
 	fixed-rate-clocks {
@@ -450,16 +509,18 @@
 		};
 	};
 
-	dp-controller {
+	dp-controller@145B0000 {
 		samsung,color-space = <0>;
 		samsung,dynamic-range = <0>;
 		samsung,ycbcr-coeff = <0>;
 		samsung,color-depth = <1>;
 		samsung,link-rate = <0x0a>;
 		samsung,lane-count = <4>;
+		status = "okay";
 	};
 
 	fimd: fimd@14400000 {
+		status = "okay";
 		display-timings {
 			native-mode = <&timing0>;
 			timing0: timing@0 {
@@ -480,4 +541,22 @@
 	rtc {
 		status = "okay";
 	};
+
+	usb_hub_bus {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		// SMSC USB3503 connected in hardware only mode as a PHY
+		usb_hub: usb_hub {
+			compatible = "smsc,usb3503a";
+
+			reset-gpios = <&gpx3 5 1>;
+			connect-gpios = <&gpd1 7 1>;
+		};
+	};
+
+	usb@12110000 {
+		usb-phy = <&usb2_phy>;
+	};
 };

arch/arm/boot/dts/exynos5250-smdk5250.dts

@@ -250,7 +250,7 @@
 		samsung,vbus-gpio = <&gpx2 6 0>;
 	};
 
-	dp-controller {
+	dp-controller@145B0000 {
 		samsung,color-space = <0>;
 		samsung,dynamic-range = <0>;
 		samsung,ycbcr-coeff = <0>;
@@ -260,21 +260,25 @@
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&dp_hpd>;
+		status = "okay";
 	};
 
-	display-timings {
-		native-mode = <&timing0>;
-		timing0: timing@0 {
-			/* 1280x800 */
-			clock-frequency = <50000>;
-			hactive = <1280>;
-			vactive = <800>;
-			hfront-porch = <4>;
-			hback-porch = <4>;
-			hsync-len = <4>;
-			vback-porch = <4>;
-			vfront-porch = <4>;
-			vsync-len = <4>;
+	fimd@14400000 {
+		status = "okay";
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing@0 {
+				/* 1280x800 */
+				clock-frequency = <50000>;
+				hactive = <1280>;
+				vactive = <800>;
+				hfront-porch = <4>;
+				hback-porch = <4>;
+				hsync-len = <4>;
+				vback-porch = <4>;
+				vfront-porch = <4>;
+				vsync-len = <4>;
+			};
 		};
 	};
 

arch/arm/boot/dts/exynos5250.dtsi

@@ -163,11 +163,21 @@
 		clock-names = "watchdog";
 	};
 
+	g2d@10850000 {
+		compatible = "samsung,exynos5250-g2d";
+		reg = <0x10850000 0x1000>;
+		interrupts = <0 91 0>;
+		clocks = <&clock 345>;
+		clock-names = "fimg2d";
+	};
+
 	codec@11000000 {
 		compatible = "samsung,mfc-v6";
 		reg = <0x11000000 0x10000>;
 		interrupts = <0 96 0>;
 		samsung,power-domain = <&pd_mfc>;
+		clocks = <&clock 266>;
+		clock-names = "mfc";
 	};
 
 	rtc {
@@ -611,28 +621,20 @@
 		interrupts = <0 94 0>;
 	};
 
-	dp-controller {
-		compatible = "samsung,exynos5-dp";
-		reg = <0x145b0000 0x1000>;
-		interrupts = <10 3>;
-		interrupt-parent = <&combiner>;
+	dp_phy: video-phy@10040720 {
+		compatible = "samsung,exynos5250-dp-video-phy";
+		reg = <0x10040720 4>;
+		#phy-cells = <0>;
+	};
+
+	dp-controller@145B0000 {
 		clocks = <&clock 342>;
 		clock-names = "dp";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		dptx-phy {
-			reg = <0x10040720>;
-			samsung,enable-mask = <1>;
-		};
+		phys = <&dp_phy>;
+		phy-names = "dp";
 	};
 
-	fimd {
-		compatible = "samsung,exynos5250-fimd";
-		interrupt-parent = <&combiner>;
-		reg = <0x14400000 0x40000>;
-		interrupt-names = "fifo", "vsync", "lcd_sys";
-		interrupts = <18 4>, <18 5>, <18 6>;
+	fimd@14400000 {
 		clocks = <&clock 133>, <&clock 339>;
 		clock-names = "sclk_fimd", "fimd";
 	};

arch/arm/boot/dts/exynos5420-pinctrl.dtsi

@@ -59,6 +59,13 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 		};
+
+		dp_hpd: dp_hpd {
+			samsung,pins = "gpx0-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samaung,pin-drv = <0>;
+		};
 	};
 
 	pinctrl@13410000 {

arch/arm/boot/dts/exynos5420-smdk5420.dts

@@ -30,4 +30,35 @@
 			clock-frequency = <24000000>;
 		};
 	};
+
+	dp-controller@145B0000 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&dp_hpd>;
+		samsung,color-space = <0>;
+		samsung,dynamic-range = <0>;
+		samsung,ycbcr-coeff = <0>;
+		samsung,color-depth = <1>;
+		samsung,link-rate = <0x0a>;
+		samsung,lane-count = <4>;
+		status = "okay";
+	};
+
+	fimd@14400000 {
+		status = "okay";
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing@0 {
+				clock-frequency = <50000>;
+				hactive = <2560>;
+				vactive = <1600>;
+				hfront-porch = <48>;
+				hback-porch = <80>;
+				hsync-len = <32>;
+				vback-porch = <16>;
+				vfront-porch = <8>;
+				vsync-len = <6>;
+			};
+		};
+	};
+
 };

arch/arm/boot/dts/exynos5420.dtsi

@@ -14,7 +14,10 @@
  */
 
 #include "exynos5.dtsi"
-/include/ "exynos5420-pinctrl.dtsi"
+#include "exynos5420-pinctrl.dtsi"
+
+#include <dt-bindings/clk/exynos-audss-clk.h>
+
 / {
 	compatible = "samsung,exynos5420";
 
@@ -65,6 +68,22 @@
 		#clock-cells = <1>;
 	};
 
+	clock_audss: audss-clock-controller@3810000 {
+		compatible = "samsung,exynos5420-audss-clock";
+		reg = <0x03810000 0x0C>;
+		#clock-cells = <1>;
+		clocks = <&clock 148>;
+		clock-names = "sclk_audio";
+	};
+
+	codec@11000000 {
+		compatible = "samsung,mfc-v7";
+		reg = <0x11000000 0x10000>;
+		interrupts = <0 96 0>;
+		clocks = <&clock 401>;
+		clock-names = "mfc";
+	};
+
 	mct@101C0000 {
 		compatible = "samsung,exynos4210-mct";
 		reg = <0x101C0000 0x800>;
@@ -90,6 +109,41 @@
 		};
 	};
 
+	gsc_pd: power-domain@10044000 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10044000 0x20>;
+	};
+
+	isp_pd: power-domain@10044020 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10044020 0x20>;
+	};
+
+	mfc_pd: power-domain@10044060 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10044060 0x20>;
+	};
+
+	disp_pd: power-domain@100440C0 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x100440C0 0x20>;
+	};
+
+	mau_pd: power-domain@100440E0 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x100440E0 0x20>;
+	};
+
+	g2d_pd: power-domain@10044100 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10044100 0x20>;
+	};
+
+	msc_pd: power-domain@10044120 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10044120 0x20>;
+	};
+
 	pinctrl_0: pinctrl@13400000 {
 		compatible = "samsung,exynos5420-pinctrl";
 		reg = <0x13400000 0x1000>;
@@ -145,4 +199,23 @@
 		clocks = <&clock 260>, <&clock 131>;
 		clock-names = "uart", "clk_uart_baud0";
 	};
+
+	dp_phy: video-phy@10040728 {
+		compatible = "samsung,exynos5250-dp-video-phy";
+		reg = <0x10040728 4>;
+		#phy-cells = <0>;
+	};
+
+	dp-controller@145B0000 {
+		clocks = <&clock 412>;
+		clock-names = "dp";
+		phys = <&dp_phy>;
+		phy-names = "dp";
+	};
+
+	fimd@14400000 {
+		samsung,power-domain = <&disp_pd>;
+		clocks = <&clock 147>, <&clock 421>;
+		clock-names = "sclk_fimd", "fimd";
+	};
 };

arch/arm/boot/dts/exynos5440.dtsi

@@ -18,6 +18,9 @@
 
 	aliases {
 		spi0 = &spi_0;
+		tmuctrl0 = &tmuctrl_0;
+		tmuctrl1 = &tmuctrl_1;
+		tmuctrl2 = &tmuctrl_2;
 	};
 
 	clock: clock-controller@160000 {
@@ -207,6 +210,30 @@
 		clock-names = "rtc";
 	};
 
+	tmuctrl_0: tmuctrl@160118 {
+		compatible = "samsung,exynos5440-tmu";
+		reg = <0x160118 0x230>, <0x160368 0x10>;
+		interrupts = <0 58 0>;
+		clocks = <&clock 21>;
+		clock-names = "tmu_apbif";
+	};
+
+	tmuctrl_1: tmuctrl@16011C {
+		compatible = "samsung,exynos5440-tmu";
+		reg = <0x16011C 0x230>, <0x160368 0x10>;
+		interrupts = <0 58 0>;
+		clocks = <&clock 21>;
+		clock-names = "tmu_apbif";
+	};
+
+	tmuctrl_2: tmuctrl@160120 {
+		compatible = "samsung,exynos5440-tmu";
+		reg = <0x160120 0x230>, <0x160368 0x10>;
+		interrupts = <0 58 0>;
+		clocks = <&clock 21>;
+		clock-names = "tmu_apbif";
+	};
+
 	sata@210000 {
 		compatible = "snps,exynos5440-ahci";
 		reg = <0x210000 0x10000>;

arch/arm/boot/dts/imx23-evk.dts

@@ -90,6 +90,11 @@
 		};
 
 		apbx@80040000 {
+			lradc@80050000 {
+				status = "okay";
+				fsl,lradc-touchscreen-wires = <4>;
+			};
+
 			pwm: pwm@80064000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pwm2_pins_a>;
@@ -107,6 +112,16 @@
 				pinctrl-0 = <&duart_pins_a>;
 				status = "okay";
 			};
+
+			usbphy0: usbphy@8007c000 {
+				status = "okay";
+			};
+		};
+	};
+
+	ahb@80080000 {
+		usb0: usb@80080000 {
+			status = "okay";
 		};
 	};
 

arch/arm/boot/dts/imx23-olinuxino.dts

@@ -69,6 +69,10 @@
 		};
 
 		apbx@80040000 {
+			lradc@80050000 {
+				status = "okay";
+			};
+
 			duart: serial@80070000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&duart_pins_a>;

arch/arm/boot/dts/imx23.dtsi

@@ -20,6 +20,8 @@
 		gpio2 = &gpio2;
 		serial0 = &auart0;
 		serial1 = &auart1;
+		spi0 = &ssp0;
+		spi1 = &ssp1;
 	};
 
 	cpus {
@@ -76,23 +78,21 @@
 				#size-cells = <1>;
 				reg = <0x8000c000 0x2000>, <0x8000a000 0x2000>;
 				reg-names = "gpmi-nand", "bch";
-				interrupts = <13>, <56>;
-				interrupt-names = "gpmi-dma", "bch";
+				interrupts = <56>;
+				interrupt-names = "bch";
 				clocks = <&clks 34>;
 				clock-names = "gpmi_io";
 				dmas = <&dma_apbh 4>;
 				dma-names = "rx-tx";
-				fsl,gpmi-dma-channel = <4>;
 				status = "disabled";
 			};
 
 			ssp0: ssp@80010000 {
 				reg = <0x80010000 0x2000>;
-				interrupts = <15 14>;
+				interrupts = <15>;
 				clocks = <&clks 33>;
 				dmas = <&dma_apbh 1>;
 				dma-names = "rx-tx";
-				fsl,ssp-dma-channel = <1>;
 				status = "disabled";
 			};
 
@@ -366,11 +366,10 @@
 
 			ssp1: ssp@80034000 {
 				reg = <0x80034000 0x2000>;
-				interrupts = <2 20>;
+				interrupts = <2>;
 				clocks = <&clks 33>;
 				dmas = <&dma_apbh 2>;
 				dma-names = "rx-tx";
-				fsl,ssp-dma-channel = <2>;
 				status = "disabled";
 			};
 
@@ -472,7 +471,7 @@
 			auart0: serial@8006c000 {
 				compatible = "fsl,imx23-auart";
 				reg = <0x8006c000 0x2000>;
-				interrupts = <24 25 23>;
+				interrupts = <24>;
 				clocks = <&clks 32>;
 				dmas = <&dma_apbx 6>, <&dma_apbx 7>;
 				dma-names = "rx", "tx";
@@ -482,7 +481,7 @@
 			auart1: serial@8006e000 {
 				compatible = "fsl,imx23-auart";
 				reg = <0x8006e000 0x2000>;
-				interrupts = <59 60 58>;
+				interrupts = <59>;
 				clocks = <&clks 32>;
 				dmas = <&dma_apbx 8>, <&dma_apbx 9>;
 				dma-names = "rx", "tx";

arch/arm/boot/dts/imx28-cfa10036.dts

@@ -23,10 +23,7 @@
 	apb@80000000 {
 		apbh@80000000 {
 			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_cfa10036>;
-
-				hog_pins_cfa10036: hog-10036@0 {
+				ssd1306_cfa10036: ssd1306-10036@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x2073 /* MX28_PAD_SSP0_D7__GPIO_2_7 */
@@ -83,6 +80,8 @@
 
 				ssd1306: oled@3c {
 					compatible = "solomon,ssd1306fb-i2c";
+					pinctrl-names = "default";
+					pinctrl-0 = <&ssd1306_cfa10036>;
 					reg = <0x3c>;
 					reset-gpios = <&gpio2 7 0>;
 					solomon,height = <32>;

arch/arm/boot/dts/imx28-cfa10037.dts

@@ -22,13 +22,19 @@
 	apb@80000000 {
 		apbh@80000000 {
 			pinctrl@80018000 {
-				pinctrl-names = "default", "default";
-				pinctrl-1 = <&hog_pins_cfa10037>;
-
-				hog_pins_cfa10037: hog-10037@0 {
+				usb_pins_cfa10037: usb-10037@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				mac0_pins_cfa10037: mac0-10037@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
 					>;
 					fsl,drive-strength = <0>;
@@ -56,7 +62,8 @@
 		mac0: ethernet@800f0000 {
 			phy-mode = "rmii";
 			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
+			pinctrl-0 = <&mac0_pins_a
+				&mac0_pins_cfa10037>;
 			phy-reset-gpios = <&gpio2 21 0>;
 			phy-reset-duration = <100>;
 			status = "okay";
@@ -68,6 +75,8 @@
 
 		reg_usb1_vbus: usb1_vbus {
 			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_pins_cfa10037>;
 			regulator-name = "usb1_vbus";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;

arch/arm/boot/dts/imx28-cfa10049.dts

@@ -22,32 +22,62 @@
 	apb@80000000 {
 		apbh@80000000 {
 			pinctrl@80018000 {
-				pinctrl-names = "default", "default";
-				pinctrl-1 = <&hog_pins_cfa10049
-					&hog_pins_cfa10049_pullup>;
-
-				hog_pins_cfa10049: hog-10049@0 {
+				usb_pins_cfa10049: usb-10049@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				i2cmux_pins_cfa10049: i2cmux-10049@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */
 						0x1173 /* MX28_PAD_LCD_D22__GPIO_1_23 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				mac0_pins_cfa10049: mac0-10049@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
-						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
 					>;
 					fsl,drive-strength = <0>;
 					fsl,voltage = <1>;
 					fsl,pull-up = <0>;
 				};
 
-				hog_pins_cfa10049_pullup: hog-10049-pullup@0 {
+				pca_pins_cfa10049: pca-10049@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x2133 /* MX28_PAD_SSP2_D3__GPIO_2_19 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				rotary_pins_cfa10049: rotary-10049@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x3183 /* MX28_PAD_I2C0_SCL__GPIO_3_24 */
 						0x3193 /* MX28_PAD_I2C0_SDA__GPIO_3_25 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				rotary_btn_pins_cfa10049: rotary-btn-10049@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
 						0x31a3 /* MX28_PAD_SAIF_SDATA0__GPIO_3_26 */
-						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
 					>;
 					fsl,drive-strength = <0>;
 					fsl,voltage = <1>;
@@ -60,6 +90,7 @@
 						0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
 						0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
 						0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
+						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
 					>;
 					fsl,drive-strength = <1>;
 					fsl,voltage = <1>;
@@ -120,6 +151,16 @@
 					fsl,pull-up = <0>;
 				};
 
+				lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
 				w1_gpio_pins: w1-gpio@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -134,7 +175,8 @@
 			lcdif@80030000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_18bit_pins_cfa10049
-					     &lcdif_pins_cfa10049>;
+					     &lcdif_pins_cfa10049
+					     &lcdif_pins_cfa10049_pullup>;
 				display = <&display>;
 				status = "okay";
 
@@ -181,6 +223,8 @@
 				compatible = "i2c-mux-gpio";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2cmux_pins_cfa10049>;
 				mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
 				i2c-parent = <&i2c1>;
 
@@ -203,6 +247,8 @@
 
 					pca9555: pca9555@20 {
 						compatible = "nxp,pca9555";
+						pinctrl-names = "default";
+						pinctrl-0 = <&pca_pins_cfa10049>;
 						interrupt-parent = <&gpio2>;
 						interrupts = <19 0x2>;
 						gpio-controller;
@@ -239,6 +285,8 @@
 
 		reg_usb1_vbus: usb1_vbus {
 			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_pins_cfa10049>;
 			regulator-name = "usb1_vbus";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
@@ -250,7 +298,8 @@
 		mac0: ethernet@800f0000 {
 			phy-mode = "rmii";
 			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
+			pinctrl-0 = <&mac0_pins_a
+				&mac0_pins_cfa10049>;
 			phy-reset-gpios = <&gpio2 21 0>;
 			phy-reset-duration = <100>;
 			status = "okay";
@@ -320,6 +369,8 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&rotary_btn_pins_cfa10049>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
@@ -333,6 +384,8 @@
 
 	rotary {
 		compatible = "rotary-encoder";
+		pinctrl-names = "default";
+		pinctrl-0 = <&rotary_pins_cfa10049>;
 		gpios = <&gpio3 24 1>, <&gpio3 25 1>;
 		linux,axis = <1>; /* REL_Y */
 		rotary-encoder,relative-axis;

arch/arm/boot/dts/imx28-cfa10055.dts

@@ -23,36 +23,13 @@
 	apb@80000000 {
 		apbh@80000000 {
 			pinctrl@80018000 {
-				pinctrl-names = "default", "default";
-				pinctrl-1 = <&hog_pins_cfa10055
-					&hog_pins_cfa10055_pullup>;
-
-				hog_pins_cfa10055: hog-10055@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
-					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <0>;
-				};
-
-				hog_pins_cfa10055_pullup: hog-10055-pullup@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
-					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <1>;
-				};
-
 				spi2_pins_cfa10055: spi2-cfa10055@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
 						0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
 						0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
+						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
 					>;
 					fsl,drive-strength = <1>;
 					fsl,voltage = <1>;
@@ -98,12 +75,23 @@
 					fsl,voltage = <1>;
 					fsl,pull-up = <0>;
 				};
+
+				lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
 			};
 
 			lcdif@80030000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&lcdif_18bit_pins_cfa10055
-					     &lcdif_pins_cfa10055>;
+					     &lcdif_pins_cfa10055
+					     &lcdif_pins_cfa10055_pullup>;
 				display = <&display>;
 				status = "okay";
 

arch/arm/boot/dts/imx28-cfa10056.dts

@@ -0,0 +1,119 @@
+/*
+ * Copyright 2013 Free Electrons
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/*
+ * The CFA-10055 is an expansion board for the CFA-10036 module and
+ * CFA-10037, thus we need to include the CFA-10037 DTS.
+ */
+/include/ "imx28-cfa10037.dts"
+
+/ {
+	model = "Crystalfontz CFA-10056 Board";
+	compatible = "crystalfontz,cfa10056", "crystalfontz,cfa10037", "crystalfontz,cfa10036", "fsl,imx28";
+
+	apb@80000000 {
+		apbh@80000000 {
+			pinctrl@80018000 {
+				spi2_pins_cfa10056: spi2-cfa10056@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
+						0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
+						0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
+						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+					>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				lcdif_pins_cfa10056: lcdif-10056@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
+						0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
+						0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
+						0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+			};
+
+			lcdif@80030000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&lcdif_24bit_pins_a
+						&lcdif_pins_cfa10056
+						&lcdif_pins_cfa10056_pullup >;
+				display = <&display>;
+				status = "okay";
+
+				display: display {
+					bits-per-pixel = <32>;
+					bus-width = <24>;
+
+					display-timings {
+						native-mode = <&timing0>;
+						timing0: timing0 {
+							clock-frequency = <32000000>;
+							hactive = <480>;
+							vactive = <800>;
+							hback-porch = <2>;
+							hfront-porch = <2>;
+							vback-porch = <2>;
+							vfront-porch = <2>;
+							hsync-len = <5>;
+							vsync-len = <5>;
+							hsync-active = <0>;
+							vsync-active = <0>;
+							de-active = <1>;
+							pixelclk-active = <1>;
+						};
+					};
+				};
+			};
+		};
+	};
+
+	spi2 {
+		compatible = "spi-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi2_pins_cfa10056>;
+		status = "okay";
+		gpio-sck = <&gpio2 16 0>;
+		gpio-mosi = <&gpio2 17 0>;
+		gpio-miso = <&gpio2 18 0>;
+		cs-gpios = <&gpio3 5 0>;
+		num-chipselects = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hx8369: hx8369@0 {
+			compatible = "himax,hx8369a", "himax,hx8369";
+			reg = <0>;
+			spi-max-frequency = <100000>;
+			spi-cpol;
+			spi-cpha;
+			gpios-reset = <&gpio3 30 0>;
+		};
+	};
+};

arch/arm/boot/dts/imx28-cfa10057.dts

@@ -23,35 +23,16 @@
 	apb@80000000 {
 		apbh@80000000 {
 			pinctrl@80018000 {
-				pinctrl-names = "default", "default";
-				pinctrl-1 = <&hog_pins_cfa10057
-					&hog_pins_cfa10057_pullup>;
-
-				hog_pins_cfa10057: hog-10057@0 {
+				usb_pins_cfa10057: usb-10057@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
 						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
-						0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
 					>;
 					fsl,drive-strength = <0>;
 					fsl,voltage = <1>;
 					fsl,pull-up = <0>;
 				};
 
-				hog_pins_cfa10057_pullup: hog-10057-pullup@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						0x2133 /* MX28_PAD_SSP2_D3__GPIO_2_19 */
-						0x3183 /* MX28_PAD_I2C0_SCL__GPIO_3_24 */
-						0x3193 /* MX28_PAD_I2C0_SDA__GPIO_3_25 */
-						0x31a3 /* MX28_PAD_SAIF_SDATA0__GPIO_3_26 */
-						0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
-					>;
-					fsl,drive-strength = <0>;
-					fsl,voltage = <1>;
-					fsl,pull-up = <1>;
-				};
-
 				lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -164,6 +145,8 @@
 
 		reg_usb1_vbus: usb1_vbus {
 			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_pins_cfa10057>;
 			regulator-name = "usb1_vbus";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;

arch/arm/boot/dts/imx28-cfa10058.dts

@@ -0,0 +1,141 @@
+/*
+ * Copyright 2013 Crystalfontz America, Inc.
+ * Copyright 2013 Free Electrons
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/*
+ * The CFA-10058 is an expansion board for the CFA-10036 module, thus we
+ * need to include the CFA-10036 DTS.
+ */
+/include/ "imx28-cfa10036.dts"
+
+/ {
+	model = "Crystalfontz CFA-10058 Board";
+	compatible = "crystalfontz,cfa10058", "crystalfontz,cfa10036", "fsl,imx28";
+
+	apb@80000000 {
+		apbh@80000000 {
+			pinctrl@80018000 {
+				usb_pins_cfa10058: usb-10058@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				lcdif_pins_cfa10058: lcdif-10058@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
+						0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
+						0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
+						0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+			};
+
+			lcdif@80030000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&lcdif_24bit_pins_a
+						 &lcdif_pins_cfa10058>;
+				display = <&display>;
+				status = "okay";
+
+				display: display {
+					bits-per-pixel = <32>;
+					bus-width = <24>;
+
+					display-timings {
+						native-mode = <&timing0>;
+						timing0: timing0 {
+							clock-frequency = <30000000>;
+							hactive = <800>;
+							vactive = <480>;
+							hback-porch = <40>;
+							hfront-porch = <40>;
+							vback-porch = <13>;
+							vfront-porch = <29>;
+							hsync-len = <8>;
+							vsync-len = <8>;
+							hsync-active = <0>;
+							vsync-active = <0>;
+							de-active = <1>;
+							pixelclk-active = <1>;
+						};
+					};
+				};
+			};
+		};
+
+		apbx@80040000 {
+			lradc@80050000 {
+				fsl,lradc-touchscreen-wires = <4>;
+				status = "okay";
+			};
+
+			pwm: pwm@80064000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pwm3_pins_b>;
+				status = "okay";
+			};
+
+			usbphy1: usbphy@8007e000 {
+				status = "okay";
+			};
+		};
+	};
+
+	ahb@80080000 {
+		usb1: usb@80090000 {
+			vbus-supply = <&reg_usb1_vbus>;
+			pinctrl-0 = <&usbphy1_pins_a>;
+			pinctrl-names = "default";
+			status = "okay";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_usb1_vbus: usb1_vbus {
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb_pins_cfa10058>;
+			compatible = "regulator-fixed";
+			regulator-name = "usb1_vbus";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			gpio = <&gpio0 7 1>;
+		};
+	};
+
+	ahb@80080000 {
+		mac0: ethernet@800f0000 {
+			phy-mode = "rmii";
+			pinctrl-names = "default";
+			pinctrl-0 = <&mac0_pins_a>;
+			phy-reset-gpios = <&gpio2 21 0>;
+			phy-reset-duration = <100>;
+			status = "okay";
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 3 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+};

arch/arm/boot/dts/imx28-m28evk.dts

@@ -235,6 +235,12 @@
 				pinctrl-0 = <&auart2_2pins_b>;
 				status = "okay";
 			};
+
+			pwm: pwm@80064000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pwm4_pins_a>;
+				status = "okay";
+			};
 		};
 	};
 
@@ -270,6 +276,13 @@
 		};
 	};
 
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 4 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+	};
+
 	regulators {
 		compatible = "simple-bus";
 

arch/arm/boot/dts/imx28.dtsi

@@ -15,6 +15,8 @@
 	interrupt-parent = <&icoll>;
 
 	aliases {
+		ethernet0 = &mac0;
+		ethernet1 = &mac1;
 		gpio0 = &gpio0;
 		gpio1 = &gpio1;
 		gpio2 = &gpio2;
@@ -27,8 +29,8 @@
 		serial2 = &auart2;
 		serial3 = &auart3;
 		serial4 = &auart4;
-		ethernet0 = &mac0;
-		ethernet1 = &mac1;
+		spi0 = &ssp1;
+		spi1 = &ssp2;
 	};
 
 	cpus {
@@ -62,9 +64,9 @@
 				reg = <0x80000000 0x2000>;
 			};
 
-			hsadc@80002000 {
+			hsadc: hsadc@80002000 {
 				reg = <0x80002000 0x2000>;
-				interrupts = <13 87>;
+				interrupts = <13>;
 				dmas = <&dma_apbh 12>;
 				dma-names = "rx";
 				status = "disabled";
@@ -86,25 +88,24 @@
 				clocks = <&clks 25>;
 			};
 
-			perfmon@80006000 {
+			perfmon: perfmon@80006000 {
 				reg = <0x80006000 0x800>;
 				interrupts = <27>;
 				status = "disabled";
 			};
 
-			gpmi-nand@8000c000 {
+			gpmi: gpmi-nand@8000c000 {
 				compatible = "fsl,imx28-gpmi-nand";
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0x8000c000 0x2000>, <0x8000a000 0x2000>;
 				reg-names = "gpmi-nand", "bch";
-				interrupts = <88>, <41>;
-				interrupt-names = "gpmi-dma", "bch";
+				interrupts = <41>;
+				interrupt-names = "bch";
 				clocks = <&clks 50>;
 				clock-names = "gpmi_io";
 				dmas = <&dma_apbh 4>;
 				dma-names = "rx-tx";
-				fsl,gpmi-dma-channel = <4>;
 				status = "disabled";
 			};
 
@@ -112,11 +113,10 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0x80010000 0x2000>;
-				interrupts = <96 82>;
+				interrupts = <96>;
 				clocks = <&clks 46>;
 				dmas = <&dma_apbh 0>;
 				dma-names = "rx-tx";
-				fsl,ssp-dma-channel = <0>;
 				status = "disabled";
 			};
 
@@ -124,11 +124,10 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0x80012000 0x2000>;
-				interrupts = <97 83>;
+				interrupts = <97>;
 				clocks = <&clks 47>;
 				dmas = <&dma_apbh 1>;
 				dma-names = "rx-tx";
-				fsl,ssp-dma-channel = <1>;
 				status = "disabled";
 			};
 
@@ -136,11 +135,10 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0x80014000 0x2000>;
-				interrupts = <98 84>;
+				interrupts = <98>;
 				clocks = <&clks 48>;
 				dmas = <&dma_apbh 2>;
 				dma-names = "rx-tx";
-				fsl,ssp-dma-channel = <2>;
 				status = "disabled";
 			};
 
@@ -148,15 +146,14 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0x80016000 0x2000>;
-				interrupts = <99 85>;
+				interrupts = <99>;
 				clocks = <&clks 49>;
 				dmas = <&dma_apbh 3>;
 				dma-names = "rx-tx";
-				fsl,ssp-dma-channel = <3>;
 				status = "disabled";
 			};
 
-			pinctrl@80018000 {
+			pinctrl: pinctrl@80018000 {
 				#address-cells = <1>;
 				#size-cells = <0>;
 				compatible = "fsl,imx28-pinctrl", "simple-bus";
@@ -521,6 +518,18 @@
 					fsl,pull-up = <1>;
 				};
 
+				saif0_pins_b: saif0@1 {
+					reg = <1>;
+					fsl,pinmux-ids = <
+						0x3150 /* MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK */
+						0x3160 /* MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK */
+						0x3170 /* MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 */
+					>;
+					fsl,drive-strength = <2>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
 				saif1_pins_a: saif1@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -639,6 +648,19 @@
 					fsl,pull-up = <0>;
 				};
 
+				lcdif_sync_pins_a: lcdif-sync@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
+						0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+						0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
+						0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
+					>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
 				can0_pins_a: can0@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -674,6 +696,21 @@
 					fsl,pull-up = <1>;
 				};
 
+				spi3_pins_a: spi3@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						0x3082 /* MX28_PAD_AUART2_RX__SSP3_D4 */
+						0x3092 /* MX28_PAD_AUART2_TX__SSP3_D5 */
+						0x2180 /* MX28_PAD_SSP3_SCK__SSP3_SCK */
+						0x2190 /* MX28_PAD_SSP3_MOSI__SSP3_CMD */
+						0x21A0 /* MX28_PAD_SSP3_MISO__SSP3_D0 */
+						0x21B0 /* MX28_PAD_SSP3_SS0__SSP3_D3 */
+					>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
 				usbphy0_pins_a: usbphy0@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
@@ -705,14 +742,14 @@
 				};
 			};
 
-			digctl@8001c000 {
+			digctl: digctl@8001c000 {
 				compatible = "fsl,imx28-digctl", "fsl,imx23-digctl";
 				reg = <0x8001c000 0x2000>;
 				interrupts = <89>;
 				status = "disabled";
 			};
 
-			etm@80022000 {
+			etm: etm@80022000 {
 				reg = <0x80022000 0x2000>;
 				status = "disabled";
 			};
@@ -733,19 +770,19 @@
 				clocks = <&clks 26>;
 			};
 
-			dcp@80028000 {
+			dcp: dcp@80028000 {
 				reg = <0x80028000 0x2000>;
 				interrupts = <52 53 54>;
 				compatible = "fsl-dcp";
 			};
 
-			pxp@8002a000 {
+			pxp: pxp@8002a000 {
 				reg = <0x8002a000 0x2000>;
 				interrupts = <39>;
 				status = "disabled";
 			};
 
-			ocotp@8002c000 {
+			ocotp: ocotp@8002c000 {
 				compatible = "fsl,ocotp";
 				reg = <0x8002c000 0x2000>;
 				status = "disabled";
@@ -756,10 +793,10 @@
 				status = "disabled";
 			};
 
-			lcdif@80030000 {
+			lcdif: lcdif@80030000 {
 				compatible = "fsl,imx28-lcdif";
 				reg = <0x80030000 0x2000>;
-				interrupts = <38 86>;
+				interrupts = <38>;
 				clocks = <&clks 55>;
 				dmas = <&dma_apbh 13>;
 				dma-names = "rx";
@@ -784,41 +821,41 @@
 				status = "disabled";
 			};
 
-			simdbg@8003c000 {
+			simdbg: simdbg@8003c000 {
 				reg = <0x8003c000 0x200>;
 				status = "disabled";
 			};
 
-			simgpmisel@8003c200 {
+			simgpmisel: simgpmisel@8003c200 {
 				reg = <0x8003c200 0x100>;
 				status = "disabled";
 			};
 
-			simsspsel@8003c300 {
+			simsspsel: simsspsel@8003c300 {
 				reg = <0x8003c300 0x100>;
 				status = "disabled";
 			};
 
-			simmemsel@8003c400 {
+			simmemsel: simmemsel@8003c400 {
 				reg = <0x8003c400 0x100>;
 				status = "disabled";
 			};
 
-			gpiomon@8003c500 {
+			gpiomon: gpiomon@8003c500 {
 				reg = <0x8003c500 0x100>;
 				status = "disabled";
 			};
 
-			simenet@8003c700 {
+			simenet: simenet@8003c700 {
 				reg = <0x8003c700 0x100>;
 				status = "disabled";
 			};
 
-			armjtag@8003c800 {
+			armjtag: armjtag@8003c800 {
 				reg = <0x8003c800 0x100>;
 				status = "disabled";
 			};
-                };
+		};
 
 		apbx@80040000 {
 			compatible = "simple-bus";
@@ -836,16 +873,15 @@
 			saif0: saif@80042000 {
 				compatible = "fsl,imx28-saif";
 				reg = <0x80042000 0x2000>;
-				interrupts = <59 80>;
+				interrupts = <59>;
 				#clock-cells = <0>;
 				clocks = <&clks 53>;
 				dmas = <&dma_apbx 4>;
 				dma-names = "rx-tx";
-				fsl,saif-dma-channel = <4>;
 				status = "disabled";
 			};
 
-			power@80044000 {
+			power: power@80044000 {
 				reg = <0x80044000 0x2000>;
 				status = "disabled";
 			};
@@ -853,15 +889,14 @@
 			saif1: saif@80046000 {
 				compatible = "fsl,imx28-saif";
 				reg = <0x80046000 0x2000>;
-				interrupts = <58 81>;
+				interrupts = <58>;
 				clocks = <&clks 54>;
 				dmas = <&dma_apbx 5>;
 				dma-names = "rx-tx";
-				fsl,saif-dma-channel = <5>;
 				status = "disabled";
 			};
 
-			lradc@80050000 {
+			lradc: lradc@80050000 {
 				compatible = "fsl,imx28-lradc";
 				reg = <0x80050000 0x2000>;
 				interrupts = <10 14 15 16 17 18 19
@@ -869,15 +904,15 @@
 				status = "disabled";
 			};
 
-			spdif@80054000 {
+			spdif: spdif@80054000 {
 				reg = <0x80054000 0x2000>;
-				interrupts = <45 66>;
+				interrupts = <45>;
 				dmas = <&dma_apbx 2>;
 				dma-names = "tx";
 				status = "disabled";
 			};
 
-			rtc@80056000 {
+			mxs_rtc: rtc@80056000 {
 				compatible = "fsl,imx28-rtc", "fsl,stmp3xxx-rtc";
 				reg = <0x80056000 0x2000>;
 				interrupts = <29>;
@@ -888,11 +923,10 @@
 				#size-cells = <0>;
 				compatible = "fsl,imx28-i2c";
 				reg = <0x80058000 0x2000>;
-				interrupts = <111 68>;
+				interrupts = <111>;
 				clock-frequency = <100000>;
 				dmas = <&dma_apbx 6>;
 				dma-names = "rx-tx";
-				fsl,i2c-dma-channel = <6>;
 				status = "disabled";
 			};
 
@@ -901,11 +935,10 @@
 				#size-cells = <0>;
 				compatible = "fsl,imx28-i2c";
 				reg = <0x8005a000 0x2000>;
-				interrupts = <110 69>;
+				interrupts = <110>;
 				clock-frequency = <100000>;
 				dmas = <&dma_apbx 7>;
 				dma-names = "rx-tx";
-				fsl,i2c-dma-channel = <7>;
 				status = "disabled";
 			};
 
@@ -918,7 +951,7 @@
 				status = "disabled";
 			};
 
-			timrot@80068000 {
+			timer: timrot@80068000 {
 				compatible = "fsl,imx28-timrot", "fsl,timrot";
 				reg = <0x80068000 0x2000>;
 				interrupts = <48 49 50 51>;
@@ -928,10 +961,9 @@
 			auart0: serial@8006a000 {
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x8006a000 0x2000>;
-				interrupts = <112 70 71>;
+				interrupts = <112>;
 				dmas = <&dma_apbx 8>, <&dma_apbx 9>;
 				dma-names = "rx", "tx";
-				fsl,auart-dma-channel = <8 9>;
 				clocks = <&clks 45>;
 				status = "disabled";
 			};
@@ -939,7 +971,7 @@
 			auart1: serial@8006c000 {
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x8006c000 0x2000>;
-				interrupts = <113 72 73>;
+				interrupts = <113>;
 				dmas = <&dma_apbx 10>, <&dma_apbx 11>;
 				dma-names = "rx", "tx";
 				clocks = <&clks 45>;
@@ -949,7 +981,7 @@
 			auart2: serial@8006e000 {
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x8006e000 0x2000>;
-				interrupts = <114 74 75>;
+				interrupts = <114>;
 				dmas = <&dma_apbx 12>, <&dma_apbx 13>;
 				dma-names = "rx", "tx";
 				clocks = <&clks 45>;
@@ -959,7 +991,7 @@
 			auart3: serial@80070000 {
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x80070000 0x2000>;
-				interrupts = <115 76 77>;
+				interrupts = <115>;
 				dmas = <&dma_apbx 14>, <&dma_apbx 15>;
 				dma-names = "rx", "tx";
 				clocks = <&clks 45>;
@@ -969,7 +1001,7 @@
 			auart4: serial@80072000 {
 				compatible = "fsl,imx28-auart", "fsl,imx23-auart";
 				reg = <0x80072000 0x2000>;
-				interrupts = <116 78 79>;
+				interrupts = <116>;
 				dmas = <&dma_apbx 0>, <&dma_apbx 1>;
 				dma-names = "rx", "tx";
 				clocks = <&clks 45>;
@@ -1026,7 +1058,7 @@
 			status = "disabled";
 		};
 
-		dflpt@800c0000 {
+		dflpt: dflpt@800c0000 {
 			reg = <0x800c0000 0x10000>;
 			status = "disabled";
 		};
@@ -1049,10 +1081,9 @@
 			status = "disabled";
 		};
 
-		switch@800f8000 {
+		etn_switch: switch@800f8000 {
 			reg = <0x800f8000 0x8000>;
 			status = "disabled";
 		};
-
 	};
 };

arch/arm/boot/dts/pxa3xx.dtsi

@@ -28,5 +28,16 @@
 			marvell,intc-priority;
 			marvell,intc-nr-irqs = <56>;
 		};
+
+		gpio: gpio@40e00000 {
+			compatible = "intel,pxa3xx-gpio";
+			reg = <0x40e00000 0x10000>;
+			interrupt-names = "gpio0", "gpio1", "gpio_mux";
+			interrupts = <8 9 10>;
+			gpio-controller;
+			#gpio-cells = <0x2>;
+			interrupt-controller;
+			#interrupt-cells = <0x2>;
+		};
 	};
 };

arch/arm/boot/dts/r8a73a4-ape6evm.dts

@@ -50,3 +50,25 @@
 		};
 	};
 };
+
+&i2c5 {
+	vdd_dvfs: max8973@1b {
+		compatible = "maxim,max8973";
+		reg = <0x1b>;
+
+		regulator-min-microvolt = <935000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&cpu0 {
+	cpu0-supply = <&vdd_dvfs>;
+	operating-points = <
+		/* kHz  uV */
+		1950000 1115000
+		1462500  995000
+	>;
+	voltage-tolerance = <1>; /* 1% */
+};

arch/arm/boot/dts/r8a73a4.dtsi

@@ -85,4 +85,137 @@
 		interrupt-parent = <&gic>;
 		interrupts = <0 69 4>;
 	};
+
+	i2c0: i2c@e6500000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "renesas,rmobile-iic";
+		reg = <0 0xe6500000 0 0x428>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 174 0x4>;
+	};
+
+	i2c1: i2c@e6510000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "renesas,rmobile-iic";
+		reg = <0 0xe6510000 0 0x428>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 175 0x4>;
+	};
+
+	i2c2: i2c@e6520000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "renesas,rmobile-iic";
+		reg = <0 0xe6520000 0 0x428>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 176 0x4>;
+	};
+
+	i2c3: i2c@e6530000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "renesas,rmobile-iic";
+		reg = <0 0xe6530000 0 0x428>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 177 0x4>;
+	};
+
+	i2c4: i2c@e6540000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "renesas,rmobile-iic";
+		reg = <0 0xe6540000 0 0x428>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 178 0x4>;
+	};
+
+	i2c5: i2c@e60b0000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "renesas,rmobile-iic";
+		reg = <0 0xe60b0000 0 0x428>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 179 0x4>;
+	};
+
+	i2c6: i2c@e6550000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "renesas,rmobile-iic";
+		reg = <0 0xe6550000 0 0x428>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 184 0x4>;
+	};
+
+	i2c7: i2c@e6560000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "renesas,rmobile-iic";
+		reg = <0 0xe6560000 0 0x428>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 185 0x4>;
+	};
+
+	i2c8: i2c@e6570000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "renesas,rmobile-iic";
+		reg = <0 0xe6570000 0 0x428>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 173 0x4>;
+	};
+
+	mmcif0: mmcif@ee200000 {
+		compatible = "renesas,sh-mmcif";
+		reg = <0 0xee200000 0 0x80>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 169 0x4>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	mmcif1: mmcif@ee220000 {
+		compatible = "renesas,sh-mmcif";
+		reg = <0 0xee220000 0 0x80>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 170 0x4>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	pfc: pfc@e6050000 {
+		compatible = "renesas,pfc-r8a73a4";
+		reg = <0 0xe6050000 0 0x9000>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	sdhi0: sdhi@ee100000 {
+		compatible = "renesas,r8a73a4-sdhi";
+		reg = <0 0xee100000 0 0x100>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 165 4>;
+		cap-sd-highspeed;
+		status = "disabled";
+	};
+
+	sdhi1: sdhi@ee120000 {
+		compatible = "renesas,r8a73a4-sdhi";
+		reg = <0 0xee120000 0 0x100>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 166 4>;
+		cap-sd-highspeed;
+		status = "disabled";
+	};
+
+	sdhi2: sdhi@ee140000 {
+		compatible = "renesas,r8a73a4-sdhi";
+		reg = <0 0xee140000 0 0x100>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 167 4>;
+		cap-sd-highspeed;
+		status = "disabled";
+	};
 };

arch/arm/boot/dts/r8a7740-armadillo800eva-reference.dts

@@ -10,6 +10,7 @@
 
 /dts-v1/;
 /include/ "r8a7740.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "armadillo 800 eva reference";
@@ -33,6 +34,21 @@
 		regulator-boot-on;
 	};
 
+	leds {
+		compatible = "gpio-leds";
+		led1 {
+			gpios = <&pfc 102 GPIO_ACTIVE_HIGH>;
+		};
+		led2 {
+			gpios = <&pfc 111 GPIO_ACTIVE_HIGH>;
+		};
+		led3 {
+			gpios = <&pfc 110 GPIO_ACTIVE_HIGH>;
+		};
+		led4 {
+			gpios = <&pfc 177 GPIO_ACTIVE_HIGH>;
+		};
+	};
 };
 
 &i2c0 {
@@ -41,5 +57,23 @@
 		reg = <0x55>;
 		interrupt-parent = <&irqpin1>;
 		interrupts = <2 0>; /* IRQ10: hwirq 2 on irqpin1 */
+		pinctrl-0 = <&st1232_pins>;
+		pinctrl-names = "default";
+		gpios = <&pfc 166 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pfc {
+	pinctrl-0 = <&scifa1_pins>;
+	pinctrl-names = "default";
+
+	scifa1_pins: scifa1 {
+		renesas,groups = "scifa1_data";
+		renesas,function = "scifa1";
+	};
+
+	st1232_pins: st1232 {
+		renesas,groups = "intc_irq10";
+		renesas,function = "intc";
 	};
 };

arch/arm/boot/dts/r8a7740.dtsi

@@ -139,4 +139,12 @@
 			      0 72 0x4
 			      0 73 0x4>;
 	};
+
+	pfc: pfc@e6050000 {
+		compatible = "renesas,pfc-r8a7740";
+		reg = <0xe6050000 0x8000>,
+		      <0xe605800c 0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 };

arch/arm/boot/dts/r8a7778.dtsi

@@ -32,4 +32,70 @@
 		reg = <0xfe438000 0x1000>,
 		      <0xfe430000 0x100>;
 	};
+
+	gpio0: gpio@ffc40000 {
+		compatible = "renesas,gpio-r8a7778", "renesas,gpio-rcar";
+		reg = <0xffc40000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 103 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 0 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio1: gpio@ffc41000 {
+		compatible = "renesas,gpio-r8a7778", "renesas,gpio-rcar";
+		reg = <0xffc41000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 103 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 32 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio2: gpio@ffc42000 {
+		compatible = "renesas,gpio-r8a7778", "renesas,gpio-rcar";
+		reg = <0xffc42000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 103 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 64 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio3: gpio@ffc43000 {
+		compatible = "renesas,gpio-r8a7778", "renesas,gpio-rcar";
+		reg = <0xffc43000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 103 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 96 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio4: gpio@ffc44000 {
+		compatible = "renesas,gpio-r8a7778", "renesas,gpio-rcar";
+		reg = <0xffc44000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 103 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 128 27>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	pfc: pfc@fffc0000 {
+		compatible = "renesas,pfc-r8a7778";
+		reg = <0xfffc000 0x118>;
+		#gpio-range-cells = <3>;
+	};
 };

arch/arm/boot/dts/r8a7779-marzen-reference.dts

@@ -11,6 +11,7 @@
 
 /dts-v1/;
 /include/ "r8a7779.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "marzen";
@@ -37,6 +38,9 @@
 	lan0@18000000 {
 		compatible = "smsc,lan9220", "smsc,lan9115";
 		reg = <0x18000000 0x100>;
+		pinctrl-0 = <&lan0_pins>;
+		pinctrl-names = "default";
+
 		phy-mode = "mii";
 		interrupt-parent = <&gic>;
 		interrupts = <0 28 0x4>;
@@ -44,4 +48,49 @@
 		vddvario-supply = <&fixedregulator3v3>;
 		vdd33a-supply = <&fixedregulator3v3>;
 	};
+
+	leds {
+		compatible = "gpio-leds";
+		led2 {
+			gpios = <&gpio4 29 GPIO_ACTIVE_HIGH>;
+		};
+		led3 {
+			gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>;
+		};
+		led4 {
+			gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&pfc {
+	pinctrl-0 = <&scif2_pins &scif4_pins &sdhi0_pins>;
+	pinctrl-names = "default";
+
+	lan0_pins: lan0 {
+		intc {
+			renesas,groups = "intc_irq1_b";
+			renesas,function = "intc";
+		};
+		lbsc {
+			renesas,groups = "lbsc_ex_cs0";
+			renesas,function = "lbsc";
+		};
+	};
+
+	scif2_pins: scif2 {
+		renesas,groups = "scif2_data_c";
+		renesas,function = "scif2";
+	};
+
+	scif4_pins: scif4 {
+		renesas,groups = "scif4_data";
+		renesas,function = "scif4";
+	};
+
+	sdhi0_pins: sdhi0 {
+		renesas,groups = "sdhi0_data4", "sdhi0_ctrl", "sdhi0_cd",
+				 "sdhi0_wp";
+		renesas,function = "sdhi0";
+	};
 };

arch/arm/boot/dts/r8a7779.dtsi

@@ -48,6 +48,90 @@
                       <0xf0000100 0x100>;
         };
 
+	gpio0: gpio@ffc40000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc40000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 141 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 0 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio1: gpio@ffc41000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc41000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 142 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 32 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio2: gpio@ffc42000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc42000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 143 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 64 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio3: gpio@ffc43000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc43000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 144 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 96 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio4: gpio@ffc44000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc44000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 145 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 128 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio5: gpio@ffc45000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc45000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 146 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 160 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio6: gpio@ffc46000 {
+		compatible = "renesas,gpio-r8a7779", "renesas,gpio-rcar";
+		reg = <0xffc46000 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 147 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 192 9>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
 	irqpin0: irqpin@fe780010 {
 		compatible = "renesas,intc-irqpin";
 		#interrupt-cells = <2>;
@@ -101,6 +185,12 @@
 		interrupts = <0 81 0x4>;
 	};
 
+	pfc: pfc@fffc0000 {
+		compatible = "renesas,pfc-r8a7779";
+		reg = <0xfffc0000 0x23c>;
+		#gpio-range-cells = <3>;
+	};
+
 	thermal@ffc48000 {
 		compatible = "renesas,rcar-thermal";
 		reg = <0xffc48000 0x38>;

arch/arm/boot/dts/r8a7790.dtsi

@@ -38,6 +38,78 @@
 		interrupts = <1 9 0xf04>;
 	};
 
+	gpio0: gpio@ffc40000 {
+		compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar";
+		reg = <0 0xffc40000 0 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 4 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 0 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio1: gpio@ffc41000 {
+		compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar";
+		reg = <0 0xffc41000 0 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 5 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 32 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio2: gpio@ffc42000 {
+		compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar";
+		reg = <0 0xffc42000 0 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 6 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 64 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio3: gpio@ffc43000 {
+		compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar";
+		reg = <0 0xffc43000 0 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 7 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 96 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio4: gpio@ffc44000 {
+		compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar";
+		reg = <0 0xffc44000 0 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 8 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 128 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
+	gpio5: gpio@ffc45000 {
+		compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar";
+		reg = <0 0xffc45000 0 0x2c>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 9 0x4>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-ranges = <&pfc 0 160 32>;
+		#interrupt-cells = <2>;
+		interrupt-controller;
+	};
+
 	timer {
 		compatible = "arm,armv7-timer";
 		interrupts = <1 13 0xf08>,
@@ -54,4 +126,64 @@
 		interrupt-parent = <&gic>;
 		interrupts = <0 0 4>, <0 1 4>, <0 2 4>,	<0 3 4>;
 	};
+
+	mmcif0: mmcif@ee200000 {
+		compatible = "renesas,sh-mmcif";
+		reg = <0 0xee200000 0 0x80>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 169 0x4>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	mmcif1: mmcif@ee220000 {
+		compatible = "renesas,sh-mmcif";
+		reg = <0 0xee220000 0 0x80>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 170 0x4>;
+		reg-io-width = <4>;
+		status = "disabled";
+	};
+
+	pfc: pfc@e6060000 {
+		compatible = "renesas,pfc-r8a7790";
+		reg = <0 0xe6060000 0 0x250>;
+		#gpio-range-cells = <3>;
+	};
+
+	sdhi0: sdhi@ee100000 {
+		compatible = "renesas,r8a7790-sdhi";
+		reg = <0 0xee100000 0 0x100>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 165 4>;
+		cap-sd-highspeed;
+		status = "disabled";
+	};
+
+	sdhi1: sdhi@ee120000 {
+		compatible = "renesas,r8a7790-sdhi";
+		reg = <0 0xee120000 0 0x100>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 166 4>;
+		cap-sd-highspeed;
+		status = "disabled";
+	};
+
+	sdhi2: sdhi@ee140000 {
+		compatible = "renesas,r8a7790-sdhi";
+		reg = <0 0xee140000 0 0x100>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 167 4>;
+		cap-sd-highspeed;
+		status = "disabled";
+	};
+
+	sdhi3: sdhi@ee160000 {
+		compatible = "renesas,r8a7790-sdhi";
+		reg = <0 0xee160000 0 0x100>;
+		interrupt-parent = <&gic>;
+		interrupts = <0 168 4>;
+		cap-sd-highspeed;
+		status = "disabled";
+	};
 };

arch/arm/boot/dts/sama5d3.dtsi

@@ -48,6 +48,11 @@
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a5-pmu";
+		interrupts = <46 IRQ_TYPE_LEVEL_HIGH 0>;
+	};
+
 	memory {
 		reg = <0x20000000 0x8000000>;
 	};

arch/arm/boot/dts/sh7372.dtsi

@@ -23,4 +23,12 @@
 			reg = <0x0>;
 		};
 	};
+
+	pfc: pfc@e6050000 {
+		compatible = "renesas,pfc-sh7372";
+		reg = <0xe6050000 0x8000>,
+		      <0xe605801c 0x1c>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 };

arch/arm/boot/dts/sh73a0-kzm9g-reference.dts

@@ -13,6 +13,7 @@
 
 /dts-v1/;
 /include/ "sh73a0.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "KZM-A9-GT";
@@ -58,6 +59,24 @@
 		regulator-boot-on;
 	};
 
+	vmmc_sdhi0: regulator@2 {
+	        compatible = "regulator-fixed";
+		regulator-name = "SDHI0 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pfc 15 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vmmc_sdhi2: regulator@3 {
+	        compatible = "regulator-fixed";
+		regulator-name = "SDHI2 Vcc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pfc 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	lan9220@10000000 {
 		compatible = "smsc,lan9220", "smsc,lan9115";
 		reg = <0x10000000 0x100>;
@@ -70,6 +89,22 @@
 		vddvario-supply = <&reg_1p8v>;
 		vdd33a-supply = <&reg_3p3v>;
 	};
+
+	leds {
+		compatible = "gpio-leds";
+		led1 {
+			gpios = <&pfc 20 GPIO_ACTIVE_LOW>;
+		};
+		led2 {
+			gpios = <&pfc 21 GPIO_ACTIVE_LOW>;
+		};
+		led3 {
+			gpios = <&pfc 22 GPIO_ACTIVE_LOW>;
+		};
+		led4 {
+			gpios = <&pfc 23 GPIO_ACTIVE_LOW>;
+		};
+	};
 };
 
 &i2c0 {
@@ -145,20 +180,71 @@
 	};
 };
 
+&i2c3 {
+	pinctrl-0 = <&i2c3_pins>;
+	pinctrl-names = "default";
+};
+
 &mmcif {
+	pinctrl-0 = <&mmcif_pins>;
+	pinctrl-names = "default";
+
 	bus-width = <8>;
 	vmmc-supply = <&reg_1p8v>;
 	status = "okay";
 };
 
+&pfc {
+	pinctrl-0 = <&scifa4_pins>;
+	pinctrl-names = "default";
+
+	i2c3_pins: i2c3 {
+		renesas,groups = "i2c3_1";
+		renesas,function = "i2c3";
+	};
+
+	mmcif_pins: mmcif {
+		mux {
+			renesas,groups = "mmc0_data8_0", "mmc0_ctrl_0";
+			renesas,function = "mmc0";
+		};
+		cfg {
+			renesas,groups = "mmc0_data8_0";
+			renesas,pins = "PORT279";
+			bias-pull-up;
+		};
+	};
+
+	scifa4_pins: scifa4 {
+		renesas,groups = "scifa4_data", "scifa4_ctrl";
+		renesas,function = "scifa4";
+	};
+
+	sdhi0_pins: sdhi0 {
+		renesas,groups = "sdhi0_data4", "sdhi0_ctrl", "sdhi0_cd", "sdhi0_wp";
+		renesas,function = "sdhi0";
+	};
+
+	sdhi2_pins: sdhi2 {
+		renesas,groups = "sdhi2_data4", "sdhi2_ctrl";
+		renesas,function = "sdhi2";
+	};
+};
+
 &sdhi0 {
-	vmmc-supply = <&reg_3p3v>;
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-names = "default";
+
+	vmmc-supply = <&vmmc_sdhi0>;
 	bus-width = <4>;
 	status = "okay";
 };
 
 &sdhi2 {
-	vmmc-supply = <&reg_3p3v>;
+	pinctrl-0 = <&sdhi2_pins>;
+	pinctrl-names = "default";
+
+	vmmc-supply = <&vmmc_sdhi2>;
 	bus-width = <4>;
 	broken-cd;
 	status = "okay";

arch/arm/boot/dts/sh73a0.dtsi

@@ -222,4 +222,12 @@
 		cap-sd-highspeed;
 		status = "disabled";
 	};
+
+	pfc: pfc@e6050000 {
+		compatible = "renesas,pfc-sh73a0";
+		reg = <0xe6050000 0x8000>,
+		      <0xe605801c 0x1c>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
 };

arch/arm/boot/dts/socfpga.dtsi

@@ -476,25 +476,25 @@
 		};
 
 		timer0: timer0@ffc08000 {
-			compatible = "snps,dw-apb-timer-sp";
+			compatible = "snps,dw-apb-timer";
 			interrupts = <0 167 4>;
 			reg = <0xffc08000 0x1000>;
 		};
 
 		timer1: timer1@ffc09000 {
-			compatible = "snps,dw-apb-timer-sp";
+			compatible = "snps,dw-apb-timer";
 			interrupts = <0 168 4>;
 			reg = <0xffc09000 0x1000>;
 		};
 
 		timer2: timer2@ffd00000 {
-			compatible = "snps,dw-apb-timer-osc";
+			compatible = "snps,dw-apb-timer";
 			interrupts = <0 169 4>;
 			reg = <0xffd00000 0x1000>;
 		};
 
 		timer3: timer3@ffd01000 {
-			compatible = "snps,dw-apb-timer-osc";
+			compatible = "snps,dw-apb-timer";
 			interrupts = <0 170 4>;
 			reg = <0xffd01000 0x1000>;
 		};

arch/arm/boot/dts/ste-ccu8540-pinctrl.dtsi

@@ -0,0 +1,196 @@
+/*
+ * Copyright 2012 ST-Ericsson
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+#include "ste-nomadik-pinctrl.dtsi"
+
+/ {
+	soc {
+		pinctrl {
+			uart0 {
+				uart0_default_mux: uart0_mux {
+					default_mux {
+						ste,function = "u0";
+						ste,pins = "u0_a_1";
+					};
+				};
+
+				uart0_default_mode: uart0_default {
+					default_cfg1 {
+						ste,pins = "GPIO0", "GPIO2";
+						ste,config = <&in_pu>;
+					};
+
+					default_cfg2 {
+						ste,pins = "GPIO1", "GPIO3";
+						ste,config = <&out_hi>;
+					};
+				};
+
+				uart0_sleep_mode: uart0_sleep {
+					sleep_cfg1 {
+						ste,pins = "GPIO0", "GPIO2";
+						ste,config = <&slpm_in_pu>;
+					};
+
+					sleep_cfg2 {
+						ste,pins = "GPIO1", "GPIO3";
+						ste,config = <&slpm_out_hi>;
+					};
+				};
+			};
+
+			uart2 {
+				uart2_default_mode: uart2_default {
+					default_mux {
+						ste,function = "u2";
+						ste,pins = "u2txrx_a_1";
+					};
+
+					default_cfg1 {
+						ste,pins = "GPIO120";
+						ste,config = <&in_pu>;
+					};
+
+					default_cfg2 {
+						ste,pins = "GPIO121";
+						ste,config = <&out_hi>;
+					};
+				};
+
+				uart2_sleep_mode: uart2_sleep {
+					sleep_cfg1 {
+						ste,pins = "GPIO120";
+						ste,config = <&slpm_in_pu>;
+					};
+
+					sleep_cfg2 {
+						ste,pins = "GPIO121";
+						ste,config = <&slpm_out_hi>;
+					};
+				};
+			};
+
+			i2c0 {
+				i2c0_default_mux: i2c_mux {
+					default_mux {
+						ste,function = "i2c0";
+						ste,pins = "i2c0_a_1";
+					};
+				};
+
+				i2c0_default_mode: i2c_default {
+					default_cfg1 {
+						ste,pins = "GPIO147", "GPIO148";
+						ste,config = <&in_pu>;
+					};
+				};
+
+				i2c0_sleep_mode: i2c_sleep {
+					sleep_cfg1 {
+						ste,pins = "GPIO147", "GPIO148";
+						ste,config = <&slpm_in_pu>;
+					};
+				};
+			};
+
+			i2c1 {
+				i2c1_default_mux: i2c_mux {
+					default_mux {
+						ste,function = "i2c1";
+						ste,pins = "i2c1_b_2";
+					};
+				};
+
+				i2c1_default_mode: i2c_default {
+					default_cfg1 {
+						ste,pins = "GPIO16", "GPIO17";
+						ste,config = <&in_pu>;
+					};
+				};
+
+				i2c1_sleep_mode: i2c_sleep {
+					sleep_cfg1 {
+						ste,pins = "GPIO16", "GPIO17";
+						ste,config = <&slpm_in_pu>;
+					};
+				};
+			};
+
+			i2c2 {
+				i2c2_default_mux: i2c_mux {
+					default_mux {
+						ste,function = "i2c2";
+						ste,pins = "i2c2_b_2";
+					};
+				};
+
+				i2c2_default_mode: i2c_default {
+					default_cfg1 {
+						ste,pins = "GPIO10", "GPIO11";
+						ste,config = <&in_pu>;
+					};
+				};
+
+				i2c2_sleep_mode: i2c_sleep {
+					sleep_cfg1 {
+						ste,pins = "GPIO11", "GPIO11";
+						ste,config = <&slpm_in_pu>;
+					};
+				};
+			};
+
+			i2c4 {
+				i2c4_default_mux: i2c_mux {
+					default_mux {
+						ste,function = "i2c4";
+						ste,pins = "i2c4_b_2";
+					};
+				};
+
+				i2c4_default_mode: i2c_default {
+					default_cfg1 {
+						ste,pins = "GPIO122", "GPIO123";
+						ste,config = <&in_pu>;
+					};
+				};
+
+				i2c4_sleep_mode: i2c_sleep {
+					sleep_cfg1 {
+						ste,pins = "GPIO122", "GPIO123";
+						ste,config = <&slpm_in_pu>;
+					};
+				};
+			};
+
+			i2c5 {
+				i2c5_default_mux: i2c_mux {
+					default_mux {
+						ste,function = "i2c5";
+						ste,pins = "i2c5_c_2";
+					};
+				};
+
+				i2c5_default_mode: i2c_default {
+					default_cfg1 {
+						ste,pins = "GPIO118", "GPIO119";
+						ste,config = <&in_pu>;
+					};
+				};
+
+				i2c5_sleep_mode: i2c_sleep {
+					sleep_cfg1 {
+						ste,pins = "GPIO118", "GPIO119";
+						ste,config = <&slpm_in_pu>;
+					};
+				};
+			};
+		};
+	};
+};

arch/arm/boot/dts/ste-ccu8540.dts

@@ -0,0 +1,86 @@
+/*
+ * Copyright 2013 ST-Ericsson AB
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "ste-dbx5x0.dtsi"
+#include "ste-ccu8540-pinctrl.dtsi"
+
+/ {
+	model = "ST-Ericsson U8540 platform with Device Tree";
+	compatible = "st-ericsson,ccu8540", "st-ericsson,u8540";
+
+	memory@0 {
+		reg = <0x20000000 0x1f000000>, <0xc0000000 0x3f000000>;
+	};
+
+	soc {
+		pinctrl {
+			compatible = "stericsson,db8540-pinctrl";
+		};
+
+		prcmu@80157000 {
+			reg = <0x80157000 0x2000>, <0x801b0000 0x8000>, <0x801b8000 0x3000>;
+			reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm";
+		};
+
+		uart@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&uart0_default_mux>, <&uart0_default_mode>;
+			pinctrl-1 = <&uart0_sleep_mode>;
+			status = "okay";
+		};
+
+		uart@80121000 {
+			status = "okay";
+		};
+
+		uart@80007000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&uart2_default_mode>;
+			pinctrl-1 = <&uart2_sleep_mode>;
+			status = "okay";
+		};
+
+		i2c0: i2c@80004000 {
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c0_default_mux>, <&i2c0_default_mode>;
+			pinctrl-1 = <&i2c0_sleep_mode>;
+		};
+
+		i2c1: i2c@80122000 {
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c1_default_mux>, <&i2c1_default_mode>;
+			pinctrl-1 = <&i2c1_sleep_mode>;
+		};
+
+		i2c2: i2c@80128000 {
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c2_default_mux>, <&i2c2_default_mode>;
+			pinctrl-1 = <&i2c2_sleep_mode>;
+		};
+
+		i2c3: i2c@80110000 {
+			status = "disabled";
+		};
+
+		i2c4: i2c@8012a000 {
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c4_default_mux>, <&i2c4_default_mode>;
+			pinctrl-1 = <&i2c4_sleep_mode>;
+		};
+
+		i2c5: i2c@80001000 {
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c5_default_mux>, <&i2c5_default_mode>;
+			pinctrl-1 = <&i2c5_sleep_mode>;
+		};
+	};
+};

arch/arm/boot/dts/ccu9540.dts → arch/arm/boot/dts/ste-ccu9540.dts

@@ -10,7 +10,7 @@
  */
 
 /dts-v1/;
-#include "dbx5x0.dtsi"
+#include "ste-dbx5x0.dtsi"
 
 / {
 	model = "ST-Ericsson CCU9540 platform with Device Tree";

arch/arm/boot/dts/dbx5x0.dtsi → arch/arm/boot/dts/ste-dbx5x0.dtsi

@@ -245,7 +245,7 @@
 					     <22 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-names = "IRQ_HOTMON_LOW", "IRQ_HOTMON_HIGH";
 				status = "disabled";
-			 };
+			};
 
 			db8500-prcmu-regulators {
 				compatible = "stericsson,db8500-prcmu-regulator";
@@ -457,8 +457,36 @@
 					stericsson,earpeice-cmv = <950>; /* Units in mV. */
 				};
 
+				ext_regulators: ab8500-ext-regulators {
+					compatible = "stericsson,ab8500-ext-regulator";
+
+					ab8500_ext1_reg: ab8500_ext1 {
+						regulator-compatible = "ab8500_ext1";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+						regulator-boot-on;
+						regulator-always-on;
+					};
+
+					ab8500_ext2_reg: ab8500_ext2 {
+						regulator-compatible = "ab8500_ext2";
+						regulator-min-microvolt = <1360000>;
+						regulator-max-microvolt = <1360000>;
+						regulator-boot-on;
+						regulator-always-on;
+					};
+
+					ab8500_ext3_reg: ab8500_ext3 {
+						regulator-compatible = "ab8500_ext3";
+						regulator-min-microvolt = <3400000>;
+						regulator-max-microvolt = <3400000>;
+						regulator-boot-on;
+					};
+				};
+
 				ab8500-regulators {
 					compatible = "stericsson,ab8500-regulator";
+					vin-supply = <&ab8500_ext3_reg>;
 
 					// supplies to the display/camera
 					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {

arch/arm/boot/dts/href.dtsi → arch/arm/boot/dts/ste-href.dtsi

@@ -10,7 +10,7 @@
  */
 
 #include <dt-bindings/interrupt-controller/irq.h>
-#include "dbx5x0.dtsi"
+#include "ste-dbx5x0.dtsi"
 
 / {
 	memory {

arch/arm/boot/dts/hrefprev60.dts → arch/arm/boot/dts/ste-hrefprev60.dts

@@ -10,9 +10,9 @@
  */
 
 /dts-v1/;
-#include "dbx5x0.dtsi"
-#include "href.dtsi"
-#include "stuib.dtsi"
+#include "ste-dbx5x0.dtsi"
+#include "ste-href.dtsi"
+#include "ste-stuib.dtsi"
 
 / {
 	model = "ST-Ericsson HREF (pre-v60) platform with Device Tree";

arch/arm/boot/dts/hrefv60plus.dts → arch/arm/boot/dts/ste-hrefv60plus.dts

@@ -10,9 +10,9 @@
  */
 
 /dts-v1/;
-#include "dbx5x0.dtsi"
-#include "href.dtsi"
-#include "stuib.dtsi"
+#include "ste-dbx5x0.dtsi"
+#include "ste-href.dtsi"
+#include "ste-stuib.dtsi"
 
 / {
 	model = "ST-Ericsson HREF (v60+) platform with Device Tree";

arch/arm/boot/dts/ste-nomadik-pinctrl.dtsi

@@ -0,0 +1,95 @@
+/*
+ * Copyright 2012 ST-Ericsson
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+#include <dt-bindings/pinctrl/nomadik.h>
+
+/ {
+	in_nopull: in_nopull {
+		ste,input = <INPUT_NOPULL>;
+	};
+
+	in_pu: input_pull_up {
+		ste,input = <INPUT_PULLUP>;
+	};
+
+	in_pd: input_pull_down {
+		ste,input = <INPUT_PULLDOWN>;
+	};
+
+	out_hi: output_high {
+		ste,output = <OUTPUT_HIGH>;
+	};
+
+	out_lo: output_low {
+		ste,output = <OUTPUT_LOW>;
+	};
+
+	gpio_out_lo: gpio_output_low {
+		ste,gpio = <GPIOMODE_ENABLED>;
+		ste,output = <OUTPUT_LOW>;
+	};
+
+	slpm_in_pu: slpm_in_pu {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-input = <SLPM_INPUT_PULLUP>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+	};
+
+	slpm_in_wkup_pdis: slpm_in_wkup_pdis {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-input = <SLPM_DIR_INPUT>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	slpm_out_lo: slpm_out_lo {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-output = <SLPM_OUTPUT_LOW>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+	};
+
+	slpm_out_hi: slpm_out_hi {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-output = <SLPM_OUTPUT_HIGH>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+	};
+
+	slpm_out_hi_wkup_pdis: slpm_out_hi_wkup_pdis {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-output = <SLPM_OUTPUT_HIGH>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	slpm_out_wkup_pdis: slpm_out_wkup_pdis {
+		ste,sleep = <SLPM_ENABLED>;
+		ste,sleep-output = <SLPM_DIR_OUTPUT>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	in_wkup_pdis: in_wkup_pdis {
+		ste,sleep-input = <SLPM_DIR_INPUT>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	out_hi_wkup_pdis: out_hi_wkup_pdis {
+		ste,sleep-output = <SLPM_OUTPUT_HIGH>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+
+	out_wkup_pdis: out_wkup_pdis {
+		ste,sleep-output = <SLPM_DIR_OUTPUT>;
+		ste,sleep-wakeup = <SLPM_WAKEUP_ENABLE>;
+		ste,sleep-pull-disable = <SLPM_PDIS_DISABLED>;
+	};
+};

arch/arm/boot/dts/ste-nomadik-stn8815.dtsi

@@ -140,18 +140,30 @@
 			};
 		};
 		i2c0 {
+			i2c0_default_mux: i2c0_mux {
+				i2c0_default_mux {
+					ste,function = "i2c0";
+					ste,pins = "i2c0_a_1";
+				};
+			};
 			i2c0_default_mode: i2c0_default {
 				i2c0_default_cfg {
 					ste,pins = "GPIO62_D3", "GPIO63_D2";
-					ste,input = <1>;
+					ste,input = <0>;
 				};
 			};
 		};
 		i2c1 {
+			i2c1_default_mux: i2c1_mux {
+				i2c1_default_mux {
+					ste,function = "i2c1";
+					ste,pins = "i2c1_a_1";
+				};
+			};
 			i2c1_default_mode: i2c1_default {
 				i2c1_default_cfg {
 					ste,pins = "GPIO53_L4", "GPIO54_L3";
-					ste,input = <1>;
+					ste,input = <0>;
 				};
 			};
 		};
@@ -159,7 +171,7 @@
 			i2c2_default_mode: i2c2_default {
 				i2c2_default_cfg {
 					ste,pins = "GPIO73_C21", "GPIO74_C20";
-					ste,input = <1>;
+					ste,input = <0>;
 				};
 			};
 		};
@@ -682,13 +694,17 @@
 
 	/* I2C0 connected to the STw4811 power management chip */
 	i2c0 {
-		compatible = "i2c-gpio";
-		gpios = <&gpio1 31 0>, /* sda */
-			<&gpio1 30 0>; /* scl */
+		compatible = "st,nomadik-i2c", "arm,primecell";
+		reg = <0x101f8000 0x1000>;
+		interrupt-parent = <&vica>;
+		interrupts = <20>;
+		clock-frequency = <100000>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+		clocks = <&i2c0clk>, <&pclki2c0>;
+		clock-names = "mclk", "apb_pclk";
 		pinctrl-names = "default";
-		pinctrl-0 = <&i2c0_default_mode>;
+		pinctrl-0 = <&i2c0_default_mux>, <&i2c0_default_mode>;
 
 		stw4811@2d {
 			   compatible = "st,stw4811";
@@ -698,13 +714,17 @@
 
 	/* I2C1 connected to various sensors */
 	i2c1 {
-		compatible = "i2c-gpio";
-		gpios = <&gpio1 22 0>, /* sda */
-			<&gpio1 21 0>; /* scl */
+		compatible = "st,nomadik-i2c", "arm,primecell";
+		reg = <0x101f7000 0x1000>;
+		interrupt-parent = <&vica>;
+		interrupts = <21>;
+		clock-frequency = <100000>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+		clocks = <&i2c1clk>, <&pclki2c1>;
+		clock-names = "mclk", "apb_pclk";
 		pinctrl-names = "default";
-		pinctrl-0 = <&i2c1_default_mode>;
+		pinctrl-0 = <&i2c1_default_mux>, <&i2c1_default_mode>;
 
 		camera@2d {
 			   compatible = "st,camera";

arch/arm/boot/dts/snowball.dts → arch/arm/boot/dts/ste-snowball.dts

@@ -10,7 +10,7 @@
  */
 
 /dts-v1/;
-#include "dbx5x0.dtsi"
+#include "ste-dbx5x0.dtsi"
 
 / {
 	model = "Calao Systems Snowball platform with device tree";
@@ -165,34 +165,6 @@
 			status = "okay";
 		};
 
-		i2c@80004000 {
-			tc3589x@42 {
-				//compatible = "tc3589x";
-				reg = <0x42>;
-				gpios = <&gpio6 25 0x4>;
-				interrupt-parent = <&gpio6>;
-			};
-			tps61052@33 {
-				//compatible = "tps61052";
-				reg = <0x33>;
-			};
-		};
-
-		i2c@80128000 {
-			lp5521@33 {
-				// compatible = "lp5521";
-				reg = <0x33>;
-			};
-			lp5521@34 {
-				// compatible = "lp5521";
-				reg = <0x34>;
-			};
-			bh1780@29 {
-				// compatible = "rohm,bh1780gli";
-				reg = <0x33>;
-			};
-		};
-
 		cpufreq-cooling {
 			status = "okay";
 		};
@@ -310,6 +282,20 @@
 					compatible = "stericsson,ab8500-gpio";
 				};
 
+				ext_regulators: ab8500-ext-regulators {
+					ab8500_ext1_reg: ab8500_ext1 {
+						regulator-name = "ab8500-ext-supply1";
+					};
+
+					ab8500_ext2_reg_reg: ab8500_ext2 {
+						regulator-name = "ab8500-ext-supply2";
+					};
+
+					ab8500_ext3_reg_reg: ab8500_ext3 {
+						regulator-name = "ab8500-ext-supply3";
+					};
+				};
+
 				ab8500-regulators {
 					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
 						regulator-name = "V-DISPLAY";

arch/arm/boot/dts/sun4i-a10-a1000.dts

@@ -0,0 +1,101 @@
+/*
+ * Copyright 2013 Emilio López
+ *
+ * Emilio López <emilio@elopez.com.ar>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "sun4i-a10.dtsi"
+
+/ {
+	model = "Mele A1000";
+	compatible = "mele,a1000", "allwinner,sun4i-a10";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	soc@01c00000 {
+		emac: ethernet@01c0b000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&emac_pins_a>;
+			phy = <&phy1>;
+			status = "okay";
+		};
+
+		mdio@01c0b080 {
+			phy-supply = <&reg_emac_3v3>;
+			status = "okay";
+
+			phy1: ethernet-phy@1 {
+				reg = <1>;
+			};
+		};
+
+		pinctrl@01c20800 {
+			emac_power_pin_a1000: emac_power_pin@0 {
+				allwinner,pins = "PH15";
+				allwinner,function = "gpio_out";
+				allwinner,drive = <0>;
+				allwinner,pull = <0>;
+			};
+
+			led_pins_a1000: led_pins@0 {
+				allwinner,pins = "PH10", "PH20";
+				allwinner,function = "gpio_out";
+				allwinner,drive = <0>;
+				allwinner,pull = <0>;
+			};
+		};
+
+		uart0: serial@01c28000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_pins_a>;
+			status = "okay";
+		};
+
+		i2c0: i2c@01c2ac00 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins_a>;
+			status = "okay";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins_a1000>;
+
+		red {
+			label = "a1000:red:usr";
+			gpios = <&pio 7 10 0>;
+		};
+
+		blue {
+			label = "a1000:blue:usr";
+			gpios = <&pio 7 20 0>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_emac_3v3: emac-3v3 {
+			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&emac_power_pin_a1000>;
+			regulator-name = "emac-3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			enable-active-high;
+			gpio = <&pio 7 15 0>;
+		};
+	};
+};

arch/arm/boot/dts/sun4i-a10-cubieboard.dts

@@ -26,7 +26,7 @@
 		bootargs = "earlyprintk console=ttyS0,115200";
 	};
 
-	soc@01c20000 {
+	soc@01c00000 {
 		emac: ethernet@01c0b000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&emac_pins_a>;
@@ -76,12 +76,12 @@
 		pinctrl-0 = <&led_pins_cubieboard>;
 
 		blue {
-			label = "cubieboard::blue";
+			label = "cubieboard:blue:usr";
 			gpios = <&pio 7 21 0>; /* LED1 */
 		};
 
 		green {
-			label = "cubieboard::green";
+			label = "cubieboard:green:usr";
 			gpios = <&pio 7 20 0>; /* LED2 */
 			linux,default-trigger = "heartbeat";
 		};

arch/arm/boot/dts/sun4i-a10-hackberry.dts

@@ -22,7 +22,7 @@
 		bootargs = "earlyprintk console=ttyS0,115200";
 	};
 
-	soc@01c20000 {
+	soc@01c00000 {
 		emac: ethernet@01c0b000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&emac_pins_a>;

arch/arm/boot/dts/sun4i-a10-mini-xplus.dts

@@ -22,7 +22,7 @@
 		bootargs = "earlyprintk console=ttyS0,115200";
 	};
 
-	soc@01c20000 {
+	soc@01c00000 {
 		uart0: serial@01c28000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart0_pins_a>;

arch/arm/boot/dts/sun4i-a10.dtsi

@@ -160,11 +160,10 @@
 		};
 	};
 
-	soc@01c20000 {
+	soc@01c00000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
-		reg = <0x01c20000 0x300000>;
 		ranges;
 
 		emac: ethernet@01c0b000 {

arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts

@@ -18,7 +18,7 @@
 	model = "Olimex A10s-Olinuxino Micro";
 	compatible = "olimex,a10s-olinuxino-micro", "allwinner,sun5i-a10s";
 
-	soc@01c20000 {
+	soc@01c00000 {
 		emac: ethernet@01c0b000 {
 			pinctrl-names = "default";
 			pinctrl-0 = <&emac_pins_a>;
@@ -60,6 +60,31 @@
 			pinctrl-0 = <&uart3_pins_a>;
 			status = "okay";
 		};
+
+		i2c0: i2c@01c2ac00 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins_a>;
+			status = "okay";
+		};
+
+		i2c1: i2c@01c2b000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c1_pins_a>;
+			status = "okay";
+
+			at24@50 {
+				compatible = "at,24c16";
+				pagesize = <16>;
+				reg = <0x50>;
+				read-only;
+			};
+		};
+
+		i2c2: i2c@01c2b400 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c2_pins_a>;
+			status = "okay";
+		};
 	};
 
 	leds {

arch/arm/boot/dts/sun5i-a10s.dtsi

@@ -157,11 +157,10 @@
 		};
 	};
 
-	soc@01c20000 {
+	soc@01c00000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
-		reg = <0x01c20000 0x300000>;
 		ranges;
 
 		emac: ethernet@01c0b000 {
@@ -229,6 +228,27 @@
 				allwinner,drive = <0>;
 				allwinner,pull = <0>;
 			};
+
+			i2c0_pins_a: i2c0@0 {
+				allwinner,pins = "PB0", "PB1";
+				allwinner,function = "i2c0";
+				allwinner,drive = <0>;
+				allwinner,pull = <0>;
+			};
+
+			i2c1_pins_a: i2c1@0 {
+				allwinner,pins = "PB15", "PB16";
+				allwinner,function = "i2c1";
+				allwinner,drive = <0>;
+				allwinner,pull = <0>;
+			};
+
+			i2c2_pins_a: i2c2@0 {
+				allwinner,pins = "PB17", "PB18";
+				allwinner,function = "i2c2";
+				allwinner,drive = <0>;
+				allwinner,pull = <0>;
+			};
 		};
 
 		timer@01c20c00 {
@@ -282,5 +302,38 @@
 			clocks = <&apb1_gates 19>;
 			status = "disabled";
 		};
+
+		i2c0: i2c@01c2ac00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "allwinner,sun4i-i2c";
+			reg = <0x01c2ac00 0x400>;
+			interrupts = <7>;
+			clocks = <&apb1_gates 0>;
+			clock-frequency = <100000>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@01c2b000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "allwinner,sun4i-i2c";
+			reg = <0x01c2b000 0x400>;
+			interrupts = <8>;
+			clocks = <&apb1_gates 1>;
+			clock-frequency = <100000>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@01c2b400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "allwinner,sun4i-i2c";
+			reg = <0x01c2b400 0x400>;
+			interrupts = <9>;
+			clocks = <&apb1_gates 2>;
+			clock-frequency = <100000>;
+			status = "disabled";
+		};
 	};
 };

arch/arm/boot/dts/sun5i-a13-olinuxino.dts

@@ -22,7 +22,7 @@
 		bootargs = "earlyprintk console=ttyS0,115200";
 	};
 
-	soc@01c20000 {
+	soc@01c00000 {
 		pinctrl@01c20800 {
 			led_pins_olinuxino: led_pins@0 {
 				allwinner,pins = "PG9";

arch/arm/boot/dts/sun5i-a13.dtsi

@@ -150,11 +150,10 @@
 		};
 	};
 
-	soc@01c20000 {
+	soc@01c00000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
-		reg = <0x01c20000 0x300000>;
 		ranges;
 
 		intc: interrupt-controller@01c20400 {

arch/arm/boot/dts/sun6i-a31-colombus.dts

@@ -0,0 +1,30 @@
+/*
+ * Copyright 2013 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "sun6i-a31.dtsi"
+
+/ {
+	model = "WITS A31 Colombus Evaluation Board";
+	compatible = "wits,colombus", "allwinner,sun6i-a31";
+
+	chosen {
+		bootargs = "earlyprintk console=ttyS0,115200";
+	};
+
+	soc@01c00000 {
+		uart0: serial@01c28000 {
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/sun6i-a31.dtsi

@@ -0,0 +1,156 @@
+/*
+ * Copyright 2013 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+		};
+
+		cpu@2 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <2>;
+		};
+
+		cpu@3 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <3>;
+		};
+	};
+
+	memory {
+		reg = <0x40000000 0x80000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		osc: oscillator {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	soc@01c00000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		timer@01c20c00 {
+			compatible = "allwinner,sun4i-timer";
+			reg = <0x01c20c00 0xa0>;
+			interrupts = <0 18 1>,
+				     <0 19 1>,
+				     <0 20 1>,
+				     <0 21 1>,
+				     <0 22 1>;
+			clocks = <&osc>;
+		};
+
+		wdt1: watchdog@01c20ca0 {
+			compatible = "allwinner,sun6i-wdt";
+			reg = <0x01c20ca0 0x20>;
+		};
+
+		uart0: serial@01c28000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28000 0x400>;
+			interrupts = <0 0 1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc>;
+			status = "disabled";
+		};
+
+		uart1: serial@01c28400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28400 0x400>;
+			interrupts = <0 1 1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc>;
+			status = "disabled";
+		};
+
+		uart2: serial@01c28800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28800 0x400>;
+			interrupts = <0 2 1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc>;
+			status = "disabled";
+		};
+
+		uart3: serial@01c28c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28c00 0x400>;
+			interrupts = <0 3 1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc>;
+			status = "disabled";
+		};
+
+		uart4: serial@01c29000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c29000 0x400>;
+			interrupts = <0 4 1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc>;
+			status = "disabled";
+		};
+
+		uart5: serial@01c29400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c29400 0x400>;
+			interrupts = <0 5 1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@01c81000 {
+			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+			reg = <0x01c81000 0x1000>,
+			      <0x01c82000 0x1000>,
+			      <0x01c84000 0x2000>,
+			      <0x01c86000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <1 9 0xf04>;
+		};
+	};
+};

arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts

@@ -0,0 +1,34 @@
+/*
+ * Copyright 2013 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "sun7i-a20.dtsi"
+
+/ {
+	model = "Olimex A20-Olinuxino Micro";
+	compatible = "olimex,a20-olinuxino-micro", "allwinner,sun7i-a20";
+
+	soc@01c00000 {
+		uart0: serial@01c28000 {
+			status = "okay";
+		};
+
+		uart6: serial@01c29800 {
+			status = "okay";
+		};
+
+		uart7: serial@01c29c00 {
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/sun7i-a20.dtsi

@@ -0,0 +1,172 @@
+/*
+ * Copyright 2013 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	memory {
+		reg = <0x40000000 0x80000000>;
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc24M: osc24M@01c20050 {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+		};
+
+		osc32k: osc32k {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+		};
+	};
+
+	soc@01c00000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		timer@01c20c00 {
+			compatible = "allwinner,sun4i-timer";
+			reg = <0x01c20c00 0x90>;
+			interrupts = <0 22 1>,
+				     <0 23 1>,
+				     <0 24 1>,
+				     <0 25 1>,
+				     <0 67 1>,
+				     <0 68 1>;
+			clocks = <&osc24M>;
+		};
+
+		wdt: watchdog@01c20c90 {
+			compatible = "allwinner,sun4i-wdt";
+			reg = <0x01c20c90 0x10>;
+		};
+
+		uart0: serial@01c28000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28000 0x400>;
+			interrupts = <0 1 1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		uart1: serial@01c28400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28400 0x400>;
+			interrupts = <0 2 1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		uart2: serial@01c28800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28800 0x400>;
+			interrupts = <0 3 1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		uart3: serial@01c28c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28c00 0x400>;
+			interrupts = <0 4 1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		uart4: serial@01c29000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c29000 0x400>;
+			interrupts = <0 17 1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		uart5: serial@01c29400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c29400 0x400>;
+			interrupts = <0 18 1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		uart6: serial@01c29800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c29800 0x400>;
+			interrupts = <0 19 1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		uart7: serial@01c29c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c29c00 0x400>;
+			interrupts = <0 20 1>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&osc24M>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@01c81000 {
+			compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
+			reg = <0x01c81000 0x1000>,
+			      <0x01c82000 0x1000>,
+			      <0x01c84000 0x2000>,
+			      <0x01c86000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <1 9 0xf04>;
+		};
+	};
+};

arch/arm/boot/dts/tegra114-dalmore.dts

@@ -791,7 +791,7 @@
 					regulator-boot-on;
 				};
 
-				dcdc3 {
+				tps65090_dcdc3_reg: dcdc3 {
 					regulator-name = "vdd-ao";
 					regulator-always-on;
 					regulator-boot-on;
@@ -836,6 +836,182 @@
 				};
 			};
 		};
+
+		palmas: tps65913 {
+			compatible = "ti,palmas";
+			reg = <0x58>;
+			interrupts = <0 86 IRQ_TYPE_LEVEL_LOW>;
+
+			#interrupt-cells = <2>;
+			interrupt-controller;
+
+			ti,system-power-controller;
+
+			palmas_gpio: gpio {
+				compatible = "ti,palmas-gpio";
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			pmic {
+				compatible = "ti,tps65913-pmic", "ti,palmas-pmic";
+				smps1-in-supply = <&tps65090_dcdc3_reg>;
+				smps3-in-supply = <&tps65090_dcdc3_reg>;
+				smps4-in-supply = <&tps65090_dcdc2_reg>;
+				smps7-in-supply = <&tps65090_dcdc2_reg>;
+				smps8-in-supply = <&tps65090_dcdc2_reg>;
+				smps9-in-supply = <&tps65090_dcdc2_reg>;
+				ldo1-in-supply = <&tps65090_dcdc2_reg>;
+				ldo2-in-supply = <&tps65090_dcdc2_reg>;
+				ldo3-in-supply = <&palmas_smps3_reg>;
+				ldo4-in-supply = <&tps65090_dcdc2_reg>;
+				ldo5-in-supply = <&vdd_ac_bat_reg>;
+				ldo6-in-supply = <&tps65090_dcdc2_reg>;
+				ldo7-in-supply = <&tps65090_dcdc2_reg>;
+				ldo8-in-supply = <&tps65090_dcdc3_reg>;
+				ldo9-in-supply = <&palmas_smps9_reg>;
+				ldoln-in-supply = <&tps65090_dcdc1_reg>;
+				ldousb-in-supply = <&tps65090_dcdc1_reg>;
+
+				regulators {
+					smps12 {
+						regulator-name = "vddio-ddr";
+						regulator-min-microvolt = <1350000>;
+						regulator-max-microvolt = <1350000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					palmas_smps3_reg: smps3 {
+						regulator-name = "vddio-1v8";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					smps45 {
+						regulator-name = "vdd-core";
+						regulator-min-microvolt = <900000>;
+						regulator-max-microvolt = <1400000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					smps457 {
+						regulator-name = "vdd-core";
+						regulator-min-microvolt = <900000>;
+						regulator-max-microvolt = <1400000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					smps8 {
+						regulator-name = "avdd-pll";
+						regulator-min-microvolt = <1050000>;
+						regulator-max-microvolt = <1050000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					palmas_smps9_reg: smps9 {
+						regulator-name = "sdhci-vdd-sd-slot";
+						regulator-min-microvolt = <2800000>;
+						regulator-max-microvolt = <2800000>;
+						regulator-always-on;
+					};
+
+					ldo1 {
+						regulator-name = "avdd-cam1";
+						regulator-min-microvolt = <2800000>;
+						regulator-max-microvolt = <2800000>;
+					};
+
+					ldo2 {
+						regulator-name = "avdd-cam2";
+						regulator-min-microvolt = <2800000>;
+						regulator-max-microvolt = <2800000>;
+					};
+
+					ldo3 {
+						regulator-name = "avdd-dsi-csi";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <1200000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					ldo4 {
+						regulator-name = "vpp-fuse";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ldo6 {
+						regulator-name = "vdd-sensor-2v85";
+						regulator-min-microvolt = <2850000>;
+						regulator-max-microvolt = <2850000>;
+					};
+
+					ldo7 {
+						regulator-name = "vdd-af-cam1";
+						regulator-min-microvolt = <2800000>;
+						regulator-max-microvolt = <2800000>;
+					};
+
+					ldo8 {
+						regulator-name = "vdd-rtc";
+						regulator-min-microvolt = <900000>;
+						regulator-max-microvolt = <900000>;
+						regulator-always-on;
+						regulator-boot-on;
+						ti,enable-ldo8-tracking;
+					};
+
+					ldo9 {
+						regulator-name = "vddio-sdmmc-2";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <3300000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					ldoln {
+						regulator-name = "hvdd-usb";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ldousb {
+						regulator-name = "avdd-usb";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					regen1 {
+						regulator-name = "rail-3v3";
+						regulator-max-microvolt = <3300000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					regen2 {
+						regulator-name = "rail-5v0";
+						regulator-max-microvolt = <5000000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+				};
+			};
+
+			rtc {
+				compatible = "ti,palmas-rtc";
+				interrupt-parent = <&palmas>;
+				interrupts = <8 0>;
+			};
+		};
 	};
 
 	spi@7000da00 {
@@ -850,6 +1026,13 @@
 
 	pmc {
 		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <1>;
+		nvidia,cpu-pwr-good-time = <500>;
+		nvidia,cpu-pwr-off-time = <300>;
+		nvidia,core-pwr-good-time = <641 3845>;
+		nvidia,core-pwr-off-time = <61036>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
 	};
 
 	ahub {
@@ -870,6 +1053,15 @@
 		non-removable;
 	};
 
+	usb@7d008000 {
+		status = "okay";
+	};
+
+	usb-phy@7d008000 {
+		status = "okay";
+		vbus-supply = <&usb3_vbus_reg>;
+	};
+
 	clocks {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -883,6 +1075,35 @@
 		};
 	};
 
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		home {
+			label = "Home";
+			gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
+			linux,code = <102>; /* KEY_HOME */
+		};
+
+		power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <116>; /* KEY_POWER */
+			gpio-key,wakeup;
+		};
+
+		volume_down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
+			linux,code = <114>; /* KEY_VOLUMEDOWN */
+		};
+
+		volume_up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <115>; /* KEY_VOLUMEUP */
+		};
+	};
+
 	regulators {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -951,6 +1172,16 @@
 			gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
 			vin-supply = <&tps65090_dcdc1_reg>;
 		};
+
+		vdd_cam_1v8_reg: regulator@6 {
+			compatible = "regulator-fixed";
+			reg = <6>;
+			regulator-name = "vdd_cam_1v8_reg";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			enable-active-high;
+			gpio = <&palmas_gpio 6 0>;
+		};
 	};
 
 	sound {
@@ -964,7 +1195,9 @@
 			"Speakers", "SPORP",
 			"Speakers", "SPORN",
 			"Speakers", "SPOLP",
-			"Speakers", "SPOLN";
+			"Speakers", "SPOLN",
+			"Mic Jack", "MICBIAS1",
+			"IN2P", "Mic Jack";
 
 		nvidia,i2s-controller = <&tegra_i2s1>;
 		nvidia,audio-codec = <&rt5640>;

arch/arm/boot/dts/tegra114-pluto.dts

@@ -1,33 +0,0 @@
-/dts-v1/;
-
-#include "tegra114.dtsi"
-
-/ {
-	model = "NVIDIA Tegra114 Pluto evaluation board";
-	compatible = "nvidia,pluto", "nvidia,tegra114";
-
-	memory {
-		reg = <0x80000000 0x40000000>;
-	};
-
-	serial@70006300 {
-		status = "okay";
-	};
-
-	pmc {
-		nvidia,invert-interrupt;
-	};
-
-	clocks {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		clk32k_in: clock {
-			compatible = "fixed-clock";
-			reg=<0>;
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
-		};
-	};
-};