selftests/timers: Add missing fflush(stdout) calls

[ Upstream commit fe48319243a626c860fd666ca032daacc2ba84a5 ]

When running under a pipe, some timer tests would not report output in
real-time because stdout flushes were missing after printf()s that lacked
a newline. This adds them to restore real-time status output that humans
can enjoy.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tools/testing/selftests/timers/adjtick.c

@@ -136,6 +136,7 @@ int check_tick_adj(long tickval)
 
 	eppm = get_ppm_drift();
 	printf("%lld usec, %lld ppm", systick + (systick * eppm / MILLION), eppm);
+	fflush(stdout);
 
 	tx1.modes = 0;
 	adjtimex(&tx1);

tools/testing/selftests/timers/leapcrash.c

@@ -101,6 +101,7 @@ int main(void)
 		}
 		clear_time_state();
 		printf(".");
+		fflush(stdout);
 	}
 	printf("[OK]\n");
 	return ksft_exit_pass();

tools/testing/selftests/timers/mqueue-lat.c

@@ -102,6 +102,7 @@ int main(int argc, char **argv)
 	int ret;
 
 	printf("Mqueue latency :                          ");
+	fflush(stdout);
 
 	ret = mqueue_lat_test();
 	if (ret < 0) {

tools/testing/selftests/timers/nanosleep.c

@@ -142,6 +142,7 @@ int main(int argc, char **argv)
 			continue;
 
 		printf("Nanosleep %-31s ", clockstring(clockid));
+		fflush(stdout);
 
 		length = 10;
 		while (length <= (NSEC_PER_SEC * 10)) {

tools/testing/selftests/timers/nsleep-lat.c

@@ -155,6 +155,7 @@ int main(int argc, char **argv)
 			continue;
 
 		printf("nsleep latency %-26s ", clockstring(clockid));
+		fflush(stdout);
 
 		length = 10;
 		while (length <= (NSEC_PER_SEC * 10)) {

tools/testing/selftests/timers/raw_skew.c

@@ -112,6 +112,7 @@ int main(int argv, char **argc)
 		printf("WARNING: ADJ_OFFSET in progress, this will cause inaccurate results\n");
 
 	printf("Estimating clock drift: ");
+	fflush(stdout);
 	sleep(120);
 
 	get_monotonic_and_raw(&mon, &raw);

tools/testing/selftests/timers/set-tai.c

@@ -55,6 +55,7 @@ int main(int argc, char **argv)
 	printf("tai offset started at %i\n", ret);
 
 	printf("Checking tai offsets can be properly set: ");
+	fflush(stdout);
 	for (i = 1; i <= 60; i++) {
 		ret = set_tai(i);
 		ret = get_tai();

tools/testing/selftests/timers/set-tz.c

@@ -65,6 +65,7 @@ int main(int argc, char **argv)
 	printf("tz_minuteswest started at %i, dst at %i\n", min, dst);
 
 	printf("Checking tz_minuteswest can be properly set: ");
+	fflush(stdout);
 	for (i = -15*60; i < 15*60; i += 30) {
 		ret = set_tz(i, dst);
 		ret = get_tz_min();
@@ -76,6 +77,7 @@ int main(int argc, char **argv)
 	printf("[OK]\n");
 
 	printf("Checking invalid tz_minuteswest values are caught: ");
+	fflush(stdout);
 
 	if (!set_tz(-15*60-1, dst)) {
 		printf("[FAILED] %i didn't return failure!\n", -15*60-1);

tools/testing/selftests/timers/threadtest.c

@@ -163,6 +163,7 @@ int main(int argc, char **argv)
 	strftime(buf, 255, "%a, %d %b %Y %T %z", localtime(&start));
 	printf("%s\n", buf);
 	printf("Testing consistency with %i threads for %ld seconds: ", thread_count, runtime);
+	fflush(stdout);
 
 	/* spawn */
 	for (i = 0; i < thread_count; i++)

tools/testing/selftests/timers/valid-adjtimex.c

@@ -123,6 +123,7 @@ int validate_freq(void)
 	/* Set the leap second insert flag */
 
 	printf("Testing ADJ_FREQ... ");
+	fflush(stdout);
 	for (i = 0; i < NUM_FREQ_VALID; i++) {
 		tx.modes = ADJ_FREQUENCY;
 		tx.freq = valid_freq[i];
@@ -250,6 +251,7 @@ int set_bad_offset(long sec, long usec, int use_nano)
 int validate_set_offset(void)
 {
 	printf("Testing ADJ_SETOFFSET... ");
+	fflush(stdout);
 
 	/* Test valid values */
 	if (set_offset(NSEC_PER_SEC - 1, 1))