Merge branch 'common/pinctrl' into sh-latest

.mailmap

@@ -111,6 +111,7 @@ Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
 Uwe Kleine-König <ukl@pengutronix.de>
 Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
 Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
+Viresh Kumar <viresh.linux@gmail.com> <viresh.kumar@st.com>
 Takashi YOSHII <takashi.yoshii.zj@renesas.com>
 Yusuke Goda <goda.yusuke@renesas.com>
 Gustavo Padovan <gustavo@las.ic.unicamp.br>

Documentation/ABI/testing/sysfs-block-rssd

@@ -1,26 +1,5 @@
-What:           /sys/block/rssd*/registers
-Date:           March 2012
-KernelVersion:  3.3
-Contact:        Asai Thambi S P <asamymuthupa@micron.com>
-Description:    This is a read-only file. Dumps below driver information and
-                hardware registers.
-                    - S ACTive
-                    - Command Issue
-                    - Completed
-                    - PORT IRQ STAT
-                    - HOST IRQ STAT
-                    - Allocated
-                    - Commands in Q
-
 What:           /sys/block/rssd*/status
 Date:           April 2012
 KernelVersion:  3.4
 Contact:        Asai Thambi S P <asamymuthupa@micron.com>
 Description:    This is a read-only file. Indicates the status of the device.
-
-What:           /sys/block/rssd*/flags
-Date:           May 2012
-KernelVersion:  3.5
-Contact:        Asai Thambi S P <asamymuthupa@micron.com>
-Description:    This is a read-only file. Dumps the flags in port and driver
-                data structure

Documentation/ABI/testing/sysfs-bus-iio

@@ -219,6 +219,7 @@ What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_voltage_scale
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY_scale
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_accel_peak_scale
 What:		/sys/bus/iio/devices/iio:deviceX/in_anglvel_scale
@@ -273,6 +274,7 @@ What:		/sys/bus/iio/devices/iio:deviceX/in_accel_scale_available
 What:		/sys/.../iio:deviceX/in_voltageX_scale_available
 What:		/sys/.../iio:deviceX/in_voltage-voltage_scale_available
 What:		/sys/.../iio:deviceX/out_voltageX_scale_available
+What:		/sys/.../iio:deviceX/out_altvoltageX_scale_available
 What:		/sys/.../iio:deviceX/in_capacitance_scale_available
 KernelVersion:	2.635
 Contact:	linux-iio@vger.kernel.org
@@ -298,14 +300,19 @@ Description:
 		gives the 3dB frequency of the filter in Hz.
 
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY_raw
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_raw
 KernelVersion:	2.6.37
 Contact:	linux-iio@vger.kernel.org
 Description:
 		Raw (unscaled, no bias etc.) output voltage for
 		channel Y.  The number must always be specified and
 		unique if the output corresponds to a single channel.
+		While DAC like devices typically use out_voltage,
+		a continuous frequency generating device, such as
+		a DDS or PLL should use out_altvoltage.
 
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY&Z_raw
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY&Z_raw
 KernelVersion:	2.6.37
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -316,6 +323,8 @@ Description:
 
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY_powerdown_mode
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltage_powerdown_mode
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_powerdown_mode
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltage_powerdown_mode
 KernelVersion:	2.6.38
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -330,6 +339,8 @@ Description:
 
 What:		/sys/.../iio:deviceX/out_votlageY_powerdown_mode_available
 What:		/sys/.../iio:deviceX/out_voltage_powerdown_mode_available
+What:		/sys/.../iio:deviceX/out_altvotlageY_powerdown_mode_available
+What:		/sys/.../iio:deviceX/out_altvoltage_powerdown_mode_available
 KernelVersion:	2.6.38
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -338,6 +349,8 @@ Description:
 
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltageY_powerdown
 What:		/sys/bus/iio/devices/iio:deviceX/out_voltage_powerdown
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_powerdown
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltage_powerdown
 KernelVersion:	2.6.38
 Contact:	linux-iio@vger.kernel.org
 Description:
@@ -346,6 +359,24 @@ Description:
 		normal operation. Y may be suppressed if all outputs are
 		controlled together.
 
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_frequency
+KernelVersion:	3.4.0
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Output frequency for channel Y in Hz. The number must always be
+		specified and unique if the output corresponds to a single
+		channel.
+
+What:		/sys/bus/iio/devices/iio:deviceX/out_altvoltageY_phase
+KernelVersion:	3.4.0
+Contact:	linux-iio@vger.kernel.org
+Description:
+		Phase in radians of one frequency/clock output Y
+		(out_altvoltageY) relative to another frequency/clock output
+		(out_altvoltageZ) of the device X. The number must always be
+		specified and unique if the output corresponds to a single
+		channel.
+
 What:		/sys/bus/iio/devices/iio:deviceX/events
 KernelVersion:	2.6.35
 Contact:	linux-iio@vger.kernel.org

Documentation/DocBook/media/v4l/pixfmt.xml

@@ -986,13 +986,13 @@ http://www.thedirks.org/winnov/</ulink></para></entry>
 	  <row id="V4L2-PIX-FMT-Y4">
 	    <entry><constant>V4L2_PIX_FMT_Y4</constant></entry>
 	    <entry>'Y04 '</entry>
-	    <entry>Old 4-bit greyscale format. Only the least significant 4 bits of each byte are used,
+	    <entry>Old 4-bit greyscale format. Only the most significant 4 bits of each byte are used,
 the other bits are set to 0.</entry>
 	  </row>
 	  <row id="V4L2-PIX-FMT-Y6">
 	    <entry><constant>V4L2_PIX_FMT_Y6</constant></entry>
 	    <entry>'Y06 '</entry>
-	    <entry>Old 6-bit greyscale format. Only the least significant 6 bits of each byte are used,
+	    <entry>Old 6-bit greyscale format. Only the most significant 6 bits of each byte are used,
 the other bits are set to 0.</entry>
 	  </row>
 	</tbody>

Documentation/DocBook/media/v4l/v4l2.xml

@@ -560,6 +560,7 @@ and discussions on the V4L mailing list.</revremark>
     &sub-g-tuner;
     &sub-log-status;
     &sub-overlay;
+    &sub-prepare-buf;
     &sub-qbuf;
     &sub-querybuf;
     &sub-querycap;
@@ -567,7 +568,6 @@ and discussions on the V4L mailing list.</revremark>
     &sub-query-dv-preset;
     &sub-query-dv-timings;
     &sub-querystd;
-    &sub-prepare-buf;
     &sub-reqbufs;
     &sub-s-hw-freq-seek;
     &sub-streamon;

Documentation/DocBook/media/v4l/vidioc-create-bufs.xml

@@ -108,10 +108,9 @@ information.</para>
 /></entry>
 	  </row>
 	  <row>
-	    <entry>__u32</entry>
+	    <entry>struct&nbsp;v4l2_format</entry>
 	    <entry><structfield>format</structfield></entry>
-	    <entry>Filled in by the application, preserved by the driver.
-	    See <xref linkend="v4l2-format" />.</entry>
+	    <entry>Filled in by the application, preserved by the driver.</entry>
 	  </row>
 	  <row>
 	    <entry>__u32</entry>

Documentation/DocBook/media/v4l/vidioc-dqevent.xml

@@ -89,7 +89,7 @@
 	  <row>
 	    <entry></entry>
 	    <entry>&v4l2-event-frame-sync;</entry>
-            <entry><structfield>frame</structfield></entry>
+            <entry><structfield>frame_sync</structfield></entry>
 	    <entry>Event data for event V4L2_EVENT_FRAME_SYNC.</entry>
 	  </row>
 	  <row>

Documentation/arm/SPEAr/overview.txt

@@ -60,4 +60,4 @@ Introduction
   Document Author
   ---------------
 
-  Viresh Kumar <viresh.kumar@st.com>, (c) 2010-2012 ST Microelectronics
+  Viresh Kumar <viresh.linux@gmail.com>, (c) 2010-2012 ST Microelectronics

Documentation/device-mapper/verity.txt

@@ -7,39 +7,39 @@ This target is read-only.
 
 Construction Parameters
 =======================
-    <version> <dev> <hash_dev> <hash_start>
+    <version> <dev> <hash_dev>
     <data_block_size> <hash_block_size>
     <num_data_blocks> <hash_start_block>
     <algorithm> <digest> <salt>
 
 <version>
-    This is the version number of the on-disk format.
+    This is the type of the on-disk hash format.
 
     0 is the original format used in the Chromium OS.
-	The salt is appended when hashing, digests are stored continuously and
-	the rest of the block is padded with zeros.
+      The salt is appended when hashing, digests are stored continuously and
+      the rest of the block is padded with zeros.
 
     1 is the current format that should be used for new devices.
-	The salt is prepended when hashing and each digest is
-	padded with zeros to the power of two.
+      The salt is prepended when hashing and each digest is
+      padded with zeros to the power of two.
 
 <dev>
-    This is the device containing the data the integrity of which needs to be
+    This is the device containing data, the integrity of which needs to be
     checked.  It may be specified as a path, like /dev/sdaX, or a device number,
     <major>:<minor>.
 
 <hash_dev>
-    This is the device that that supplies the hash tree data.  It may be
+    This is the device that supplies the hash tree data.  It may be
     specified similarly to the device path and may be the same device.  If the
-    same device is used, the hash_start should be outside of the dm-verity
-    configured device size.
+    same device is used, the hash_start should be outside the configured
+    dm-verity device.
 
 <data_block_size>
-    The block size on a data device.  Each block corresponds to one digest on
-    the hash device.
+    The block size on a data device in bytes.
+    Each block corresponds to one digest on the hash device.
 
 <hash_block_size>
-    The size of a hash block.
+    The size of a hash block in bytes.
 
 <num_data_blocks>
     The number of data blocks on the data device.  Additional blocks are
@@ -65,7 +65,7 @@ Construction Parameters
 Theory of operation
 ===================
 
-dm-verity is meant to be setup as part of a verified boot path.  This
+dm-verity is meant to be set up as part of a verified boot path.  This
 may be anything ranging from a boot using tboot or trustedgrub to just
 booting from a known-good device (like a USB drive or CD).
 
@@ -73,20 +73,20 @@ When a dm-verity device is configured, it is expected that the caller
 has been authenticated in some way (cryptographic signatures, etc).
 After instantiation, all hashes will be verified on-demand during
 disk access.  If they cannot be verified up to the root node of the
-tree, the root hash, then the I/O will fail.  This should identify
+tree, the root hash, then the I/O will fail.  This should detect
 tampering with any data on the device and the hash data.
 
 Cryptographic hashes are used to assert the integrity of the device on a
-per-block basis.  This allows for a lightweight hash computation on first read
-into the page cache.  Block hashes are stored linearly-aligned to the nearest
-block the size of a page.
+per-block basis. This allows for a lightweight hash computation on first read
+into the page cache. Block hashes are stored linearly, aligned to the nearest
+block size.
 
 Hash Tree
 ---------
 
 Each node in the tree is a cryptographic hash.  If it is a leaf node, the hash
-is of some block data on disk.  If it is an intermediary node, then the hash is
-of a number of child nodes.
+of some data block on disk is calculated. If it is an intermediary node,
+the hash of a number of child nodes is calculated.
 
 Each entry in the tree is a collection of neighboring nodes that fit in one
 block.  The number is determined based on block_size and the size of the
@@ -110,63 +110,23 @@ alg = sha256, num_blocks = 32768, block_size = 4096
 On-disk format
 ==============
 
-Below is the recommended on-disk format. The verity kernel code does not
-read the on-disk header. It only reads the hash blocks which directly
-follow the header. It is expected that a user-space tool will verify the
-integrity of the verity_header and then call dmsetup with the correct
-parameters. Alternatively, the header can be omitted and the dmsetup
-parameters can be passed via the kernel command-line in a rooted chain
-of trust where the command-line is verified.
+The verity kernel code does not read the verity metadata on-disk header.
+It only reads the hash blocks which directly follow the header.
+It is expected that a user-space tool will verify the integrity of the
+verity header.
 
-The on-disk format is especially useful in cases where the hash blocks
-are on a separate partition. The magic number allows easy identification
-of the partition contents. Alternatively, the hash blocks can be stored
-in the same partition as the data to be verified. In such a configuration
-the filesystem on the partition would be sized a little smaller than
-the full-partition, leaving room for the hash blocks.
-
-struct superblock {
-	uint8_t signature[8]
-		"verity\0\0";
-
-	uint8_t version;
-		1 - current format
-
-	uint8_t data_block_bits;
-		log2(data block size)
-
-	uint8_t hash_block_bits;
-		log2(hash block size)
-
-	uint8_t pad1[1];
-		zero padding
-
-	uint16_t salt_size;
-		big-endian salt size
-
-	uint8_t pad2[2];
-		zero padding
-
-	uint32_t data_blocks_hi;
-		big-endian high 32 bits of the 64-bit number of data blocks
-
-	uint32_t data_blocks_lo;
-		big-endian low 32 bits of the 64-bit number of data blocks
-
-	uint8_t algorithm[16];
-		cryptographic algorithm
-
-	uint8_t salt[384];
-		salt (the salt size is specified above)
-
-	uint8_t pad3[88];
-		zero padding to 512-byte boundary
-}
+Alternatively, the header can be omitted and the dmsetup parameters can
+be passed via the kernel command-line in a rooted chain of trust where
+the command-line is verified.
 
 Directly following the header (and with sector number padded to the next hash
 block boundary) are the hash blocks which are stored a depth at a time
 (starting from the root), sorted in order of increasing index.
 
+The full specification of kernel parameters and on-disk metadata format
+is available at the cryptsetup project's wiki page
+  http://code.google.com/p/cryptsetup/wiki/DMVerity
+
 Status
 ======
 V (for Valid) is returned if every check performed so far was valid.
@@ -174,21 +134,22 @@ If any check failed, C (for Corruption) is returned.
 
 Example
 =======
-
-Setup a device:
-  dmsetup create vroot --table \
-    "0 2097152 "\
-    "verity 1 /dev/sda1 /dev/sda2 4096 4096 2097152 1 "\
+Set up a device:
+  # dmsetup create vroot --readonly --table \
+    "0 2097152 verity 1 /dev/sda1 /dev/sda2 4096 4096 262144 1 sha256 "\
     "4392712ba01368efdf14b05c76f9e4df0d53664630b5d48632ed17a137f39076 "\
     "1234000000000000000000000000000000000000000000000000000000000000"
 
 A command line tool veritysetup is available to compute or verify
-the hash tree or activate the kernel driver.  This is available from
-the LVM2 upstream repository and may be supplied as a package called
-device-mapper-verity-tools:
-    git://sources.redhat.com/git/lvm2
-    http://sourceware.org/git/?p=lvm2.git
-    http://sourceware.org/cgi-bin/cvsweb.cgi/LVM2/verity?cvsroot=lvm2
-
-veritysetup -a vroot /dev/sda1 /dev/sda2 \
-	4392712ba01368efdf14b05c76f9e4df0d53664630b5d48632ed17a137f39076
+the hash tree or activate the kernel device. This is available from
+the cryptsetup upstream repository http://code.google.com/p/cryptsetup/
+(as a libcryptsetup extension).
+
+Create hash on the device:
+  # veritysetup format /dev/sda1 /dev/sda2
+  ...
+  Root hash: 4392712ba01368efdf14b05c76f9e4df0d53664630b5d48632ed17a137f39076
+
+Activate the device:
+  # veritysetup create vroot /dev/sda1 /dev/sda2 \
+    4392712ba01368efdf14b05c76f9e4df0d53664630b5d48632ed17a137f39076

Documentation/devicetree/bindings/input/fsl-mma8450.txt

@@ -2,6 +2,7 @@
 
 Required properties:
 - compatible : "fsl,mma8450".
+- reg: the I2C address of MMA8450
 
 Example:
 

Documentation/devicetree/bindings/mfd/mc13xxx.txt

@@ -46,8 +46,8 @@ Examples:
 
 ecspi@70010000 { /* ECSPI1 */
 	fsl,spi-num-chipselects = <2>;
-	cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */
-		   <&gpio3 25 0>; /* GPIO4_25 */
+	cs-gpios = <&gpio4 24 0>, /* GPIO4_24 */
+		   <&gpio4 25 0>; /* GPIO4_25 */
 	status = "okay";
 
 	pmic: mc13892@0 {

Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt

@@ -29,6 +29,6 @@ esdhc@70008000 {
 	compatible = "fsl,imx51-esdhc";
 	reg = <0x70008000 0x4000>;
 	interrupts = <2>;
-	cd-gpios = <&gpio0 6 0>; /* GPIO1_6 */
-	wp-gpios = <&gpio0 5 0>; /* GPIO1_5 */
+	cd-gpios = <&gpio1 6 0>; /* GPIO1_6 */
+	wp-gpios = <&gpio1 5 0>; /* GPIO1_5 */
 };

Documentation/devicetree/bindings/net/fsl-fec.txt

@@ -19,6 +19,6 @@ ethernet@83fec000 {
 	reg = <0x83fec000 0x4000>;
 	interrupts = <87>;
 	phy-mode = "mii";
-	phy-reset-gpios = <&gpio1 14 0>; /* GPIO2_14 */
+	phy-reset-gpios = <&gpio2 14 0>; /* GPIO2_14 */
 	local-mac-address = [00 04 9F 01 1B B9];
 };

Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt

@@ -17,6 +17,6 @@ ecspi@70010000 {
 	reg = <0x70010000 0x4000>;
 	interrupts = <36>;
 	fsl,spi-num-chipselects = <2>;
-	cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */
-		   <&gpio3 25 0>; /* GPIO4_25 */
+	cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */
+		   <&gpio3 25 0>; /* GPIO3_25 */
 };

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -3,6 +3,7 @@ Device tree binding vendor prefix registry.  Keep list in alphabetical order.
 This isn't an exhaustive list, but you should add new prefixes to it before
 using them to avoid name-space collisions.
 
+ad	Avionic Design GmbH
 adi	Analog Devices, Inc.
 amcc	Applied Micro Circuits Corporation (APM, formally AMCC)
 apm	Applied Micro Circuits Corporation (APM)

Documentation/prctl/no_new_privs.txt

@@ -0,0 +1,57 @@
+The execve system call can grant a newly-started program privileges that
+its parent did not have.  The most obvious examples are setuid/setgid
+programs and file capabilities.  To prevent the parent program from
+gaining these privileges as well, the kernel and user code must be
+careful to prevent the parent from doing anything that could subvert the
+child.  For example:
+
+ - The dynamic loader handles LD_* environment variables differently if
+   a program is setuid.
+
+ - chroot is disallowed to unprivileged processes, since it would allow
+   /etc/passwd to be replaced from the point of view of a process that
+   inherited chroot.
+
+ - The exec code has special handling for ptrace.
+
+These are all ad-hoc fixes.  The no_new_privs bit (since Linux 3.5) is a
+new, generic mechanism to make it safe for a process to modify its
+execution environment in a manner that persists across execve.  Any task
+can set no_new_privs.  Once the bit is set, it is inherited across fork,
+clone, and execve and cannot be unset.  With no_new_privs set, execve
+promises not to grant the privilege to do anything that could not have
+been done without the execve call.  For example, the setuid and setgid
+bits will no longer change the uid or gid; file capabilities will not
+add to the permitted set, and LSMs will not relax constraints after
+execve.
+
+To set no_new_privs, use prctl(PR_SET_NO_NEW_PRIVS, 1, 0, 0, 0).
+
+Be careful, though: LSMs might also not tighten constraints on exec
+in no_new_privs mode.  (This means that setting up a general-purpose
+service launcher to set no_new_privs before execing daemons may
+interfere with LSM-based sandboxing.)
+
+Note that no_new_privs does not prevent privilege changes that do not
+involve execve.  An appropriately privileged task can still call
+setuid(2) and receive SCM_RIGHTS datagrams.
+
+There are two main use cases for no_new_privs so far:
+
+ - Filters installed for the seccomp mode 2 sandbox persist across
+   execve and can change the behavior of newly-executed programs.
+   Unprivileged users are therefore only allowed to install such filters
+   if no_new_privs is set.
+
+ - By itself, no_new_privs can be used to reduce the attack surface
+   available to an unprivileged user.  If everything running with a
+   given uid has no_new_privs set, then that uid will be unable to
+   escalate its privileges by directly attacking setuid, setgid, and
+   fcap-using binaries; it will need to compromise something without the
+   no_new_privs bit set first.
+
+In the future, other potentially dangerous kernel features could become
+available to unprivileged tasks if no_new_privs is set.  In principle,
+several options to unshare(2) and clone(2) would be safe when
+no_new_privs is set, and no_new_privs + chroot is considerable less
+dangerous than chroot by itself.

Documentation/stable_kernel_rules.txt

@@ -12,6 +12,12 @@ Rules on what kind of patches are accepted, and which ones are not, into the
    marked CONFIG_BROKEN), an oops, a hang, data corruption, a real
    security issue, or some "oh, that's not good" issue.  In short, something
    critical.
+ - Serious issues as reported by a user of a distribution kernel may also
+   be considered if they fix a notable performance or interactivity issue.
+   As these fixes are not as obvious and have a higher risk of a subtle
+   regression they should only be submitted by a distribution kernel
+   maintainer and include an addendum linking to a bugzilla entry if it
+   exists and additional information on the user-visible impact.
  - New device IDs and quirks are also accepted.
  - No "theoretical race condition" issues, unless an explanation of how the
    race can be exploited is also provided.

Documentation/virtual/kvm/api.txt

@@ -1930,6 +1930,23 @@ The "pte_enc" field provides a value that can OR'ed into the hash
 PTE's RPN field (ie, it needs to be shifted left by 12 to OR it
 into the hash PTE second double word).
 
+4.75 KVM_IRQFD
+
+Capability: KVM_CAP_IRQFD
+Architectures: x86
+Type: vm ioctl
+Parameters: struct kvm_irqfd (in)
+Returns: 0 on success, -1 on error
+
+Allows setting an eventfd to directly trigger a guest interrupt.
+kvm_irqfd.fd specifies the file descriptor to use as the eventfd and
+kvm_irqfd.gsi specifies the irqchip pin toggled by this event.  When
+an event is tiggered on the eventfd, an interrupt is injected into
+the guest using the specified gsi pin.  The irqfd is removed using
+the KVM_IRQFD_FLAG_DEASSIGN flag, specifying both kvm_irqfd.fd
+and kvm_irqfd.gsi.
+
+
 5. The kvm_run structure
 ------------------------
 

MAINTAINERS

@@ -579,7 +579,7 @@ F:	drivers/net/appletalk/
 F:	net/appletalk/
 
 ARASAN COMPACT FLASH PATA CONTROLLER
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 L:	linux-ide@vger.kernel.org
 S:	Maintained
 F:	include/linux/pata_arasan_cf_data.h
@@ -4654,8 +4654,8 @@ L:	netfilter@vger.kernel.org
 L:	coreteam@netfilter.org
 W:	http://www.netfilter.org/
 W:	http://www.iptables.org/
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-2.6.git
-T:	git git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next-2.6.git
+T:	git git://1984.lsi.us.es/nf
+T:	git git://1984.lsi.us.es/nf-next
 S:	Supported
 F:	include/linux/netfilter*
 F:	include/linux/netfilter/
@@ -5296,7 +5296,7 @@ S:	Maintained
 F:	drivers/pinctrl/
 
 PIN CONTROLLER - ST SPEAR
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 W:	http://www.st.com/spear
@@ -5873,7 +5873,7 @@ S:	Maintained
 F:	drivers/tty/serial
 
 SYNOPSYS DESIGNWARE DMAC DRIVER
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 S:	Maintained
 F:	include/linux/dw_dmac.h
 F:	drivers/dma/dw_dmac_regs.h
@@ -6021,7 +6021,7 @@ S:	Maintained
 F:	drivers/mmc/host/sdhci-s3c.c
 
 SECURE DIGITAL HOST CONTROLLER INTERFACE (SDHCI) ST SPEAR DRIVER
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 L:	spear-devel@list.st.com
 L:	linux-mmc@vger.kernel.org
 S:	Maintained
@@ -6377,7 +6377,7 @@ S:	Maintained
 F:	include/linux/compiler.h
 
 SPEAR PLATFORM SUPPORT
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 M:	Shiraz Hashim <shiraz.hashim@st.com>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -6386,7 +6386,7 @@ S:	Maintained
 F:	arch/arm/plat-spear/
 
 SPEAR13XX MACHINE SUPPORT
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 M:	Shiraz Hashim <shiraz.hashim@st.com>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -6395,7 +6395,7 @@ S:	Maintained
 F:	arch/arm/mach-spear13xx/
 
 SPEAR3XX MACHINE SUPPORT
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 M:	Shiraz Hashim <shiraz.hashim@st.com>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -6406,7 +6406,7 @@ F:	arch/arm/mach-spear3xx/
 SPEAR6XX MACHINE SUPPORT
 M:	Rajeev Kumar <rajeev-dlh.kumar@st.com>
 M:	Shiraz Hashim <shiraz.hashim@st.com>
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 W:	http://www.st.com/spear
@@ -6414,7 +6414,7 @@ S:	Maintained
 F:	arch/arm/mach-spear6xx/
 
 SPEAR CLOCK FRAMEWORK SUPPORT
-M:	Viresh Kumar <viresh.kumar@st.com>
+M:     Viresh Kumar <viresh.linux@gmail.com>
 L:	spear-devel@list.st.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 W:	http://www.st.com/spear
@@ -7421,7 +7421,7 @@ F:	include/linux/vlynq.h
 
 VME SUBSYSTEM
 M:	Martyn Welch <martyn.welch@ge.com>
-M:	Manohar Vanga <manohar.vanga@cern.ch>
+M:	Manohar Vanga <manohar.vanga@gmail.com>
 M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 L:	devel@driverdev.osuosl.org
 S:	Maintained

Makefile

@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 5
 SUBLEVEL = 0
-EXTRAVERSION = -rc3
+EXTRAVERSION = -rc6
 NAME = Saber-toothed Squirrel
 
 # *DOCUMENTATION*

arch/arm/Kconfig

@@ -589,6 +589,7 @@ config ARCH_ORION5X
 	select PCI
 	select ARCH_REQUIRE_GPIOLIB
 	select GENERIC_CLOCKEVENTS
+	select NEED_MACH_IO_H
 	select PLAT_ORION
 	help
 	  Support for the following Marvell Orion 5x series SoCs:

arch/arm/boot/dts/omap2.dtsi

@@ -44,6 +44,8 @@
 			compatible = "ti,omap2-intc";
 			interrupt-controller;
 			#interrupt-cells = <1>;
+			ti,intc-size = <96>;
+			reg = <0x480FE000 0x1000>;
 		};
 
 		uart1: serial@4806a000 {

arch/arm/boot/dts/spear1310-evb.dts

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr1310 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear1310.dtsi

@@ -1,7 +1,7 @@
 /*
  * DTS file for all SPEAr1310 SoCs
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear1340-evb.dts

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr1340 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear1340.dtsi

@@ -1,7 +1,7 @@
 /*
  * DTS file for all SPEAr1340 SoCs
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear13xx.dtsi

@@ -1,7 +1,7 @@
 /*
  * DTS file for all SPEAr13xx SoCs
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear300-evb.dts

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr300 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear300.dtsi

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr300 SoC
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear310-evb.dts

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr310 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear310.dtsi

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr310 SoC
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear320-evb.dts

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr320 Evaluation Baord
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear320.dtsi

@@ -1,7 +1,7 @@
 /*
  * DTS file for SPEAr320 SoC
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/boot/dts/spear3xx.dtsi

@@ -1,7 +1,7 @@
 /*
  * DTS file for all SPEAr3xx SoCs
  *
- * Copyright 2012 Viresh Kumar <viresh.kumar@st.com>
+ * Copyright 2012 Viresh Kumar <viresh.linux@gmail.com>
  *
  * The code contained herein is licensed under the GNU General Public
  * License. You may obtain a copy of the GNU General Public License

arch/arm/include/asm/atomic.h

@@ -243,7 +243,7 @@ typedef struct {
 
 #define ATOMIC64_INIT(i) { (i) }
 
-static inline u64 atomic64_read(atomic64_t *v)
+static inline u64 atomic64_read(const atomic64_t *v)
 {
 	u64 result;
 

arch/arm/include/asm/domain.h

@@ -60,13 +60,13 @@
 #ifndef __ASSEMBLY__
 
 #ifdef CONFIG_CPU_USE_DOMAINS
-#define set_domain(x)					\
-	do {						\
-	__asm__ __volatile__(				\
-	"mcr	p15, 0, %0, c3, c0	@ set domain"	\
-	  : : "r" (x));					\
-	isb();						\
-	} while (0)
+static inline void set_domain(unsigned val)
+{
+	asm volatile(
+	"mcr	p15, 0, %0, c3, c0	@ set domain"
+	  : : "r" (val));
+	isb();
+}
 
 #define modify_domain(dom,type)					\
 	do {							\
@@ -78,8 +78,8 @@
 	} while (0)
 
 #else
-#define set_domain(x)		do { } while (0)
-#define modify_domain(dom,type)	do { } while (0)
+static inline void set_domain(unsigned val) { }
+static inline void modify_domain(unsigned dom, unsigned type)	{ }
 #endif
 
 /*

arch/arm/include/asm/futex.h

@@ -19,6 +19,7 @@
 	"	.long	1b, 4f, 2b, 4f\n"			\
 	"	.popsection\n"					\
 	"	.pushsection .fixup,\"ax\"\n"			\
+	"	.align	2\n"					\
 	"4:	mov	%0, " err_reg "\n"			\
 	"	b	3b\n"					\
 	"	.popsection"

arch/arm/include/asm/hardware/sp810.h

@@ -4,7 +4,7 @@
  * ARM PrimeXsys System Controller SP810 header file
  *
  * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/include/asm/thread_info.h

@@ -148,7 +148,6 @@ extern int vfp_restore_user_hwstate(struct user_vfp __user *,
 #define TIF_NOTIFY_RESUME	2	/* callback before returning to user */
 #define TIF_SYSCALL_TRACE	8
 #define TIF_SYSCALL_AUDIT	9
-#define TIF_SYSCALL_RESTARTSYS	10
 #define TIF_POLLING_NRFLAG	16
 #define TIF_USING_IWMMXT	17
 #define TIF_MEMDIE		18	/* is terminating due to OOM killer */
@@ -164,11 +163,9 @@ extern int vfp_restore_user_hwstate(struct user_vfp __user *,
 #define _TIF_POLLING_NRFLAG	(1 << TIF_POLLING_NRFLAG)
 #define _TIF_USING_IWMMXT	(1 << TIF_USING_IWMMXT)
 #define _TIF_SECCOMP		(1 << TIF_SECCOMP)
-#define _TIF_SYSCALL_RESTARTSYS	(1 << TIF_SYSCALL_RESTARTSYS)
 
 /* Checks for any syscall work in entry-common.S */
-#define _TIF_SYSCALL_WORK (_TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT | \
-			   _TIF_SYSCALL_RESTARTSYS)
+#define _TIF_SYSCALL_WORK (_TIF_SYSCALL_TRACE | _TIF_SYSCALL_AUDIT)
 
 /*
  * Change these and you break ASM code in entry-common.S

arch/arm/kernel/entry-armv.S

@@ -495,6 +495,7 @@ ENDPROC(__und_usr)
  * The out of line fixup for the ldrt above.
  */
 	.pushsection .fixup, "ax"
+	.align	2
 4:	mov	pc, r9
 	.popsection
 	.pushsection __ex_table,"a"

arch/arm/kernel/kprobes-test-arm.c

@@ -187,8 +187,8 @@ void kprobe_arm_test_cases(void)
 	TEST_BF_R ("mov	pc, r",0,2f,"")
 	TEST_BF_RR("mov	pc, r",0,2f,", asl r",1,0,"")
 	TEST_BB(   "sub	pc, pc, #1b-2b+8")
-#if __LINUX_ARM_ARCH__ >= 6
-	TEST_BB(   "sub	pc, pc, #1b-2b+8-2") /* UNPREDICTABLE before ARMv6 */
+#if __LINUX_ARM_ARCH__ == 6 && !defined(CONFIG_CPU_V7)
+	TEST_BB(   "sub	pc, pc, #1b-2b+8-2") /* UNPREDICTABLE before and after ARMv6 */
 #endif
 	TEST_BB_R( "sub	pc, pc, r",14, 1f-2f+8,"")
 	TEST_BB_R( "rsb	pc, r",14,1f-2f+8,", pc")

arch/arm/kernel/kprobes-thumb.c

@@ -660,7 +660,7 @@ static const union decode_item t32_table_1111_100x[] = {
 	/* LDRSB (literal)	1111 1001 x001 1111 xxxx xxxx xxxx xxxx */
 	/* LDRH (literal)	1111 1000 x011 1111 xxxx xxxx xxxx xxxx */
 	/* LDRSH (literal)	1111 1001 x011 1111 xxxx xxxx xxxx xxxx */
-	DECODE_EMULATEX	(0xfe5f0000, 0xf81f0000, t32_simulate_ldr_literal,
+	DECODE_SIMULATEX(0xfe5f0000, 0xf81f0000, t32_simulate_ldr_literal,
 						 REGS(PC, NOSPPCX, 0, 0, 0)),
 
 	/* STRB (immediate)	1111 1000 0000 xxxx xxxx 1xxx xxxx xxxx */

arch/arm/kernel/perf_event.c

@@ -503,7 +503,7 @@ __hw_perf_event_init(struct perf_event *event)
 	     event_requires_mode_exclusion(&event->attr)) {
 		pr_debug("ARM performance counters do not support "
 			 "mode exclusion\n");
-		return -EPERM;
+		return -EOPNOTSUPP;
 	}
 
 	/*

arch/arm/kernel/ptrace.c

@@ -25,7 +25,6 @@
 #include <linux/regset.h>
 #include <linux/audit.h>
 #include <linux/tracehook.h>
-#include <linux/unistd.h>
 
 #include <asm/pgtable.h>
 #include <asm/traps.h>
@@ -918,8 +917,6 @@ asmlinkage int syscall_trace(int why, struct pt_regs *regs, int scno)
 		audit_syscall_entry(AUDIT_ARCH_ARM, scno, regs->ARM_r0,
 				    regs->ARM_r1, regs->ARM_r2, regs->ARM_r3);
 
-	if (why == 0 && test_and_clear_thread_flag(TIF_SYSCALL_RESTARTSYS))
-		scno = __NR_restart_syscall - __NR_SYSCALL_BASE;
 	if (!test_thread_flag(TIF_SYSCALL_TRACE))
 		return scno;
 

arch/arm/kernel/signal.c

@@ -27,6 +27,7 @@
  */
 #define SWI_SYS_SIGRETURN	(0xef000000|(__NR_sigreturn)|(__NR_OABI_SYSCALL_BASE))
 #define SWI_SYS_RT_SIGRETURN	(0xef000000|(__NR_rt_sigreturn)|(__NR_OABI_SYSCALL_BASE))
+#define SWI_SYS_RESTART		(0xef000000|__NR_restart_syscall|__NR_OABI_SYSCALL_BASE)
 
 /*
  * With EABI, the syscall number has to be loaded into r7.
@@ -46,6 +47,18 @@ const unsigned long sigreturn_codes[7] = {
 	MOV_R7_NR_RT_SIGRETURN, SWI_SYS_RT_SIGRETURN, SWI_THUMB_RT_SIGRETURN,
 };
 
+/*
+ * Either we support OABI only, or we have EABI with the OABI
+ * compat layer enabled.  In the later case we don't know if
+ * user space is EABI or not, and if not we must not clobber r7.
+ * Always using the OABI syscall solves that issue and works for
+ * all those cases.
+ */
+const unsigned long syscall_restart_code[2] = {
+	SWI_SYS_RESTART,	/* swi	__NR_restart_syscall */
+	0xe49df004,		/* ldr	pc, [sp], #4 */
+};
+
 /*
  * atomically swap in the new signal mask, and wait for a signal.
  */
@@ -592,10 +605,12 @@ static void do_signal(struct pt_regs *regs, int syscall)
 		case -ERESTARTNOHAND:
 		case -ERESTARTSYS:
 		case -ERESTARTNOINTR:
-		case -ERESTART_RESTARTBLOCK:
 			regs->ARM_r0 = regs->ARM_ORIG_r0;
 			regs->ARM_pc = restart_addr;
 			break;
+		case -ERESTART_RESTARTBLOCK:
+			regs->ARM_r0 = -EINTR;
+			break;
 		}
 	}
 
@@ -611,14 +626,12 @@ static void do_signal(struct pt_regs *regs, int syscall)
 		 * debugger has chosen to restart at a different PC.
 		 */
 		if (regs->ARM_pc == restart_addr) {
-			if (retval == -ERESTARTNOHAND ||
-			    retval == -ERESTART_RESTARTBLOCK
+			if (retval == -ERESTARTNOHAND
 			    || (retval == -ERESTARTSYS
 				&& !(ka.sa.sa_flags & SA_RESTART))) {
 				regs->ARM_r0 = -EINTR;
 				regs->ARM_pc = continue_addr;
 			}
-			clear_thread_flag(TIF_SYSCALL_RESTARTSYS);
 		}
 
 		handle_signal(signr, &ka, &info, regs);
@@ -632,8 +645,29 @@ static void do_signal(struct pt_regs *regs, int syscall)
 		 * ignore the restart.
 		 */
 		if (retval == -ERESTART_RESTARTBLOCK
-		    && regs->ARM_pc == restart_addr)
-			set_thread_flag(TIF_SYSCALL_RESTARTSYS);
+		    && regs->ARM_pc == continue_addr) {
+			if (thumb_mode(regs)) {
+				regs->ARM_r7 = __NR_restart_syscall - __NR_SYSCALL_BASE;
+				regs->ARM_pc -= 2;
+			} else {
+#if defined(CONFIG_AEABI) && !defined(CONFIG_OABI_COMPAT)
+				regs->ARM_r7 = __NR_restart_syscall;
+				regs->ARM_pc -= 4;
+#else
+				u32 __user *usp;
+
+				regs->ARM_sp -= 4;
+				usp = (u32 __user *)regs->ARM_sp;
+
+				if (put_user(regs->ARM_pc, usp) == 0) {
+					regs->ARM_pc = KERN_RESTART_CODE;
+				} else {
+					regs->ARM_sp += 4;
+					force_sigsegv(0, current);
+				}
+#endif
+			}
+		}
 	}
 
 	restore_saved_sigmask();

arch/arm/kernel/signal.h

@@ -8,5 +8,7 @@
  * published by the Free Software Foundation.
  */
 #define KERN_SIGRETURN_CODE	(CONFIG_VECTORS_BASE + 0x00000500)
+#define KERN_RESTART_CODE	(KERN_SIGRETURN_CODE + sizeof(sigreturn_codes))
 
 extern const unsigned long sigreturn_codes[7];
+extern const unsigned long syscall_restart_code[2];

arch/arm/kernel/traps.c

@@ -820,6 +820,8 @@ void __init early_trap_init(void *vectors_base)
 	 */
 	memcpy((void *)(vectors + KERN_SIGRETURN_CODE - CONFIG_VECTORS_BASE),
 	       sigreturn_codes, sizeof(sigreturn_codes));
+	memcpy((void *)(vectors + KERN_RESTART_CODE - CONFIG_VECTORS_BASE),
+	       syscall_restart_code, sizeof(syscall_restart_code));
 
 	flush_icache_range(vectors, vectors + PAGE_SIZE);
 	modify_domain(DOMAIN_USER, DOMAIN_CLIENT);

arch/arm/kernel/vmlinux.lds.S

@@ -183,7 +183,9 @@ SECTIONS
 	}
 #endif
 
+#ifdef CONFIG_SMP
 	PERCPU_SECTION(L1_CACHE_BYTES)
+#endif
 
 #ifdef CONFIG_XIP_KERNEL
 	__data_loc = ALIGN(4);		/* location in binary */

arch/arm/mach-dove/include/mach/bridge-regs.h

@@ -50,5 +50,6 @@
 #define POWER_MANAGEMENT	(BRIDGE_VIRT_BASE | 0x011c)
 
 #define TIMER_VIRT_BASE		(BRIDGE_VIRT_BASE | 0x0300)
+#define TIMER_PHYS_BASE         (BRIDGE_PHYS_BASE | 0x0300)
 
 #endif

arch/arm/mach-dove/include/mach/dove.h

@@ -78,6 +78,7 @@
 
 /* North-South Bridge */
 #define BRIDGE_VIRT_BASE	(DOVE_SB_REGS_VIRT_BASE | 0x20000)
+#define BRIDGE_PHYS_BASE	(DOVE_SB_REGS_PHYS_BASE | 0x20000)
 
 /* Cryptographic Engine */
 #define DOVE_CRYPT_PHYS_BASE	(DOVE_SB_REGS_PHYS_BASE | 0x30000)

arch/arm/mach-exynos/Kconfig

@@ -212,7 +212,7 @@ config MACH_SMDKV310
 	select EXYNOS_DEV_SYSMMU
 	select EXYNOS4_DEV_AHCI
 	select SAMSUNG_DEV_KEYPAD
-	select EXYNOS4_DEV_DMA
+	select EXYNOS_DEV_DMA
 	select SAMSUNG_DEV_PWM
 	select EXYNOS4_DEV_USB_OHCI
 	select EXYNOS4_SETUP_FIMD0
@@ -264,7 +264,7 @@ config MACH_UNIVERSAL_C210
 	select S5P_DEV_ONENAND
 	select S5P_DEV_TV
 	select EXYNOS_DEV_SYSMMU
-	select EXYNOS4_DEV_DMA
+	select EXYNOS_DEV_DMA
 	select EXYNOS_DEV_DRM
 	select EXYNOS4_SETUP_FIMD0
 	select EXYNOS4_SETUP_I2C1
@@ -303,7 +303,7 @@ config MACH_NURI
 	select S5P_DEV_MFC
 	select S5P_DEV_USB_EHCI
 	select S5P_SETUP_MIPIPHY
-	select EXYNOS4_DEV_DMA
+	select EXYNOS_DEV_DMA
 	select EXYNOS_DEV_DRM
 	select EXYNOS4_SETUP_FIMC
 	select EXYNOS4_SETUP_FIMD0
@@ -341,7 +341,7 @@ config MACH_ORIGEN
 	select SAMSUNG_DEV_PWM
 	select EXYNOS_DEV_DRM
 	select EXYNOS_DEV_SYSMMU
-	select EXYNOS4_DEV_DMA
+	select EXYNOS_DEV_DMA
 	select EXYNOS4_DEV_USB_OHCI
 	select EXYNOS4_SETUP_FIMD0
 	select EXYNOS4_SETUP_SDHCI

arch/arm/mach-imx/clk-imx35.c

@@ -201,7 +201,6 @@ int __init mx35_clocks_init()
 			pr_err("i.MX35 clk %d: register failed with %ld\n",
 				i, PTR_ERR(clk[i]));
 
-
 	clk_register_clkdev(clk[pata_gate], NULL, "pata_imx");
 	clk_register_clkdev(clk[can1_gate], NULL, "flexcan.0");
 	clk_register_clkdev(clk[can2_gate], NULL, "flexcan.1");
@@ -264,6 +263,14 @@ int __init mx35_clocks_init()
 	clk_prepare_enable(clk[iim_gate]);
 	clk_prepare_enable(clk[emi_gate]);
 
+	/*
+	 * SCC is needed to boot via mmc after a watchdog reset. The clock code
+	 * before conversion to common clk also enabled UART1 (which isn't
+	 * handled here and not needed for mmc) and IIM (which is enabled
+	 * unconditionally above).
+	 */
+	clk_prepare_enable(clk[scc_gate]);
+
 	imx_print_silicon_rev("i.MX35", mx35_revision());
 
 #ifdef CONFIG_MXC_USE_EPIT

arch/arm/mach-imx/clk-imx6q.c

@@ -152,13 +152,14 @@ enum mx6q_clks {
 	ssi2, ssi3, uart_ipg, uart_serial, usboh3, usdhc1, usdhc2, usdhc3,
 	usdhc4, vdo_axi, vpu_axi, cko1, pll1_sys, pll2_bus, pll3_usb_otg,
 	pll4_audio, pll5_video, pll6_mlb, pll7_usb_host, pll8_enet, ssi1_ipg,
-	ssi2_ipg, ssi3_ipg, clk_max
+	ssi2_ipg, ssi3_ipg, rom,
+	clk_max
 };
 
 static struct clk *clk[clk_max];
 
 static enum mx6q_clks const clks_init_on[] __initconst = {
-	mmdc_ch0_axi, mmdc_ch1_axi,
+	mmdc_ch0_axi, rom,
 };
 
 int __init mx6q_clocks_init(void)
@@ -364,6 +365,7 @@ int __init mx6q_clocks_init(void)
 	clk[gpmi_bch]     = imx_clk_gate2("gpmi_bch",      "usdhc4",            base + 0x78, 26);
 	clk[gpmi_io]      = imx_clk_gate2("gpmi_io",       "enfc",              base + 0x78, 28);
 	clk[gpmi_apb]     = imx_clk_gate2("gpmi_apb",      "usdhc3",            base + 0x78, 30);
+	clk[rom]          = imx_clk_gate2("rom",           "ahb",               base + 0x7c, 0);
 	clk[sata]         = imx_clk_gate2("sata",          "ipg",               base + 0x7c, 4);
 	clk[sdma]         = imx_clk_gate2("sdma",          "ahb",               base + 0x7c, 6);
 	clk[spba]         = imx_clk_gate2("spba",          "ipg",               base + 0x7c, 12);

arch/arm/mach-imx/mach-imx27_visstrim_m10.c

@@ -38,7 +38,7 @@
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/time.h>
-#include <asm/system.h>
+#include <asm/system_info.h>
 #include <mach/common.h>
 #include <mach/iomux-mx27.h>
 

arch/arm/mach-kirkwood/board-iconnect.c

@@ -20,9 +20,6 @@
 #include <linux/mv643xx_eth.h>
 #include <linux/gpio.h>
 #include <linux/leds.h>
-#include <linux/spi/flash.h>
-#include <linux/spi/spi.h>
-#include <linux/spi/orion_spi.h>
 #include <linux/i2c.h>
 #include <linux/input.h>
 #include <linux/gpio_keys.h>

arch/arm/mach-kirkwood/common.c

@@ -159,6 +159,7 @@ static struct clk __init *clk_register_gate_fn(struct device *dev,
 	gate_fn->gate.flags = clk_gate_flags;
 	gate_fn->gate.lock = lock;
 	gate_fn->gate.hw.init = &init;
+	gate_fn->fn = fn;
 
 	/* ops is the gate ops, but with our disable function */
 	if (clk_gate_fn_ops.disable != clk_gate_fn_disable) {

arch/arm/mach-kirkwood/include/mach/bridge-regs.h

@@ -38,6 +38,7 @@
 #define IRQ_MASK_HIGH_OFF	0x0014
 
 #define TIMER_VIRT_BASE		(BRIDGE_VIRT_BASE | 0x0300)
+#define TIMER_PHYS_BASE		(BRIDGE_PHYS_BASE | 0x0300)
 
 #define L2_CONFIG_REG		(BRIDGE_VIRT_BASE | 0x0128)
 #define L2_WRITETHROUGH		0x00000010

arch/arm/mach-kirkwood/include/mach/kirkwood.h

@@ -80,6 +80,7 @@
 #define  UART1_VIRT_BASE	(DEV_BUS_VIRT_BASE | 0x2100)
 
 #define BRIDGE_VIRT_BASE	(KIRKWOOD_REGS_VIRT_BASE | 0x20000)
+#define BRIDGE_PHYS_BASE	(KIRKWOOD_REGS_PHYS_BASE | 0x20000)
 
 #define CRYPTO_PHYS_BASE	(KIRKWOOD_REGS_PHYS_BASE | 0x30000)
 

arch/arm/mach-mmp/include/mach/gpio-pxa.h

@@ -1,29 +0,0 @@
-#ifndef __ASM_MACH_GPIO_PXA_H
-#define __ASM_MACH_GPIO_PXA_H
-
-#include <mach/addr-map.h>
-#include <mach/cputype.h>
-#include <mach/irqs.h>
-
-#define GPIO_REGS_VIRT	(APB_VIRT_BASE + 0x19000)
-
-#define BANK_OFF(n)	(((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
-#define GPIO_REG(x)	(*(volatile u32 *)(GPIO_REGS_VIRT + (x)))
-
-#define gpio_to_bank(gpio)	((gpio) >> 5)
-
-/* NOTE: these macros are defined here to make optimization of
- * gpio_{get,set}_value() to work when 'gpio' is a constant.
- * Usage of these macros otherwise is no longer recommended,
- * use generic GPIO API whenever possible.
- */
-#define GPIO_bit(gpio)	(1 << ((gpio) & 0x1f))
-
-#define GPLR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x00)
-#define GPDR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x0c)
-#define GPSR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x18)
-#define GPCR(x)		GPIO_REG(BANK_OFF(gpio_to_bank(x)) + 0x24)
-
-#include <plat/gpio-pxa.h>
-
-#endif /* __ASM_MACH_GPIO_PXA_H */

arch/arm/mach-mv78xx0/include/mach/bridge-regs.h

@@ -31,5 +31,6 @@
 #define IRQ_MASK_HIGH_OFF	0x0014
 
 #define TIMER_VIRT_BASE		(BRIDGE_VIRT_BASE | 0x0300)
+#define TIMER_PHYS_BASE		(BRIDGE_PHYS_BASE | 0x0300)
 
 #endif

arch/arm/mach-mv78xx0/include/mach/mv78xx0.h

@@ -42,6 +42,7 @@
 #define MV78XX0_CORE0_REGS_PHYS_BASE	0xf1020000
 #define MV78XX0_CORE1_REGS_PHYS_BASE	0xf1024000
 #define MV78XX0_CORE_REGS_VIRT_BASE	0xfe400000
+#define MV78XX0_CORE_REGS_PHYS_BASE	0xfe400000
 #define MV78XX0_CORE_REGS_SIZE		SZ_16K
 
 #define MV78XX0_PCIE_IO_PHYS_BASE(i)	(0xf0800000 + ((i) << 20))
@@ -59,6 +60,7 @@
  * Core-specific peripheral registers.
  */
 #define BRIDGE_VIRT_BASE	(MV78XX0_CORE_REGS_VIRT_BASE)
+#define BRIDGE_PHYS_BASE	(MV78XX0_CORE_REGS_PHYS_BASE)
 
 /*
  * Register Map

arch/arm/mach-mxs/mach-apx4devkit.c

@@ -205,6 +205,16 @@ static int apx4devkit_phy_fixup(struct phy_device *phy)
 	return 0;
 }
 
+static void __init apx4devkit_fec_phy_clk_enable(void)
+{
+	struct clk *clk;
+
+	/* Enable fec phy clock */
+	clk = clk_get_sys("enet_out", NULL);
+	if (!IS_ERR(clk))
+		clk_prepare_enable(clk);
+}
+
 static void __init apx4devkit_init(void)
 {
 	mx28_soc_init();
@@ -225,6 +235,7 @@ static void __init apx4devkit_init(void)
 	phy_register_fixup_for_uid(PHY_ID_KS8051, MICREL_PHY_ID_MASK,
 			apx4devkit_phy_fixup);
 
+	apx4devkit_fec_phy_clk_enable();
 	mx28_add_fec(0, &mx28_fec_pdata);
 
 	mx28_add_mxs_mmc(0, &apx4devkit_mmc_pdata);

arch/arm/mach-omap2/board-flash.c

@@ -97,11 +97,6 @@ __init board_onenand_init(struct mtd_partition *onenand_parts,
 
 	gpmc_onenand_init(&board_onenand_data);
 }
-#else
-void
-__init board_onenand_init(struct mtd_partition *nor_parts, u8 nr_parts, u8 cs)
-{
-}
 #endif /* CONFIG_MTD_ONENAND_OMAP2 || CONFIG_MTD_ONENAND_OMAP2_MODULE */
 
 #if defined(CONFIG_MTD_NAND_OMAP2) || \

arch/arm/mach-omap2/board-n8x0.c

@@ -83,11 +83,9 @@ static struct musb_hdrc_config musb_config = {
 };
 
 static struct musb_hdrc_platform_data tusb_data = {
-#if defined(CONFIG_USB_MUSB_OTG)
+#ifdef CONFIG_USB_GADGET_MUSB_HDRC
 	.mode		= MUSB_OTG,
-#elif defined(CONFIG_USB_MUSB_PERIPHERAL)
-	.mode		= MUSB_PERIPHERAL,
-#else /* defined(CONFIG_USB_MUSB_HOST) */
+#else
 	.mode		= MUSB_HOST,
 #endif
 	.set_power	= tusb_set_power,

arch/arm/mach-omap2/board-omap3beagle.c

@@ -81,13 +81,13 @@ static u8 omap3_beagle_version;
 static struct {
 	int mmc1_gpio_wp;
 	int usb_pwr_level;
-	int reset_gpio;
+	int dvi_pd_gpio;
 	int usr_button_gpio;
 	int mmc_caps;
 } beagle_config = {
 	.mmc1_gpio_wp = -EINVAL,
 	.usb_pwr_level = GPIOF_OUT_INIT_LOW,
-	.reset_gpio = 129,
+	.dvi_pd_gpio = -EINVAL,
 	.usr_button_gpio = 4,
 	.mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 };
@@ -126,21 +126,21 @@ static void __init omap3_beagle_init_rev(void)
 		printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
 		beagle_config.mmc1_gpio_wp = 29;
-		beagle_config.reset_gpio = 170;
+		beagle_config.dvi_pd_gpio = 170;
 		beagle_config.usr_button_gpio = 7;
 		break;
 	case 6:
 		printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
 		beagle_config.mmc1_gpio_wp = 23;
-		beagle_config.reset_gpio = 170;
+		beagle_config.dvi_pd_gpio = 170;
 		beagle_config.usr_button_gpio = 7;
 		break;
 	case 5:
 		printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
 		omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
 		beagle_config.mmc1_gpio_wp = 23;
-		beagle_config.reset_gpio = 170;
+		beagle_config.dvi_pd_gpio = 170;
 		beagle_config.usr_button_gpio = 7;
 		break;
 	case 0:
@@ -274,11 +274,9 @@ static int beagle_twl_gpio_setup(struct device *dev,
 		if (r)
 			pr_err("%s: unable to configure nDVI_PWR_EN\n",
 				__func__);
-		r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH,
-				     "DVI_LDO_EN");
-		if (r)
-			pr_err("%s: unable to configure DVI_LDO_EN\n",
-				__func__);
+
+		beagle_config.dvi_pd_gpio = gpio + 2;
+
 	} else {
 		/*
 		 * REVISIT: need ehci-omap hooks for external VBUS
@@ -287,7 +285,7 @@ static int beagle_twl_gpio_setup(struct device *dev,
 		if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
 			pr_err("%s: unable to configure EHCI_nOC\n", __func__);
 	}
-	dvi_panel.power_down_gpio = beagle_config.reset_gpio;
+	dvi_panel.power_down_gpio = beagle_config.dvi_pd_gpio;
 
 	gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level,
 			"nEN_USB_PWR");
@@ -499,7 +497,7 @@ static void __init omap3_beagle_init(void)
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
 	omap3_beagle_init_rev();
 
-	if (beagle_config.mmc1_gpio_wp != -EINVAL)
+	if (gpio_is_valid(beagle_config.mmc1_gpio_wp))
 		omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
 	mmc[0].caps = beagle_config.mmc_caps;
 	omap_hsmmc_init(mmc);
@@ -510,15 +508,13 @@ static void __init omap3_beagle_init(void)
 
 	platform_add_devices(omap3_beagle_devices,
 			ARRAY_SIZE(omap3_beagle_devices));
+	if (gpio_is_valid(beagle_config.dvi_pd_gpio))
+		omap_mux_init_gpio(beagle_config.dvi_pd_gpio, OMAP_PIN_OUTPUT);
 	omap_display_init(&beagle_dss_data);
 	omap_serial_init();
 	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
 				  mt46h32m32lf6_sdrc_params);
 
-	omap_mux_init_gpio(170, OMAP_PIN_INPUT);
-	/* REVISIT leave DVI powered down until it's needed ... */
-	gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
-
 	usb_musb_init(NULL);
 	usbhs_init(&usbhs_bdata);
 	omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,

arch/arm/mach-omap2/board-overo.c

@@ -494,8 +494,8 @@ static void __init overo_init(void)
 
 	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
 	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-	omap_hsmmc_init(mmc);
 	overo_i2c_init();
+	omap_hsmmc_init(mmc);
 	omap_display_init(&overo_dss_data);
 	omap_serial_init();
 	omap_sdrc_init(mt46h32m32lf6_sdrc_params,

arch/arm/mach-omap2/clock44xx_data.c

@@ -84,6 +84,7 @@ static struct clk slimbus_clk = {
 
 static struct clk sys_32k_ck = {
 	.name		= "sys_32k_ck",
+	.clkdm_name	= "prm_clkdm",
 	.rate		= 32768,
 	.ops		= &clkops_null,
 };
@@ -512,6 +513,7 @@ static struct clk ddrphy_ck = {
 	.name		= "ddrphy_ck",
 	.parent		= &dpll_core_m2_ck,
 	.ops		= &clkops_null,
+	.clkdm_name	= "l3_emif_clkdm",
 	.fixed_div	= 2,
 	.recalc		= &omap_fixed_divisor_recalc,
 };
@@ -769,6 +771,7 @@ static const struct clksel dpll_mpu_m2_div[] = {
 static struct clk dpll_mpu_m2_ck = {
 	.name		= "dpll_mpu_m2_ck",
 	.parent		= &dpll_mpu_ck,
+	.clkdm_name	= "cm_clkdm",
 	.clksel		= dpll_mpu_m2_div,
 	.clksel_reg	= OMAP4430_CM_DIV_M2_DPLL_MPU,
 	.clksel_mask	= OMAP4430_DPLL_CLKOUT_DIV_MASK,
@@ -1149,6 +1152,7 @@ static const struct clksel l3_div_div[] = {
 static struct clk l3_div_ck = {
 	.name		= "l3_div_ck",
 	.parent		= &div_core_ck,
+	.clkdm_name	= "cm_clkdm",
 	.clksel		= l3_div_div,
 	.clksel_reg	= OMAP4430_CM_CLKSEL_CORE,
 	.clksel_mask	= OMAP4430_CLKSEL_L3_MASK,
@@ -2824,6 +2828,7 @@ static const struct clksel trace_clk_div_div[] = {
 static struct clk trace_clk_div_ck = {
 	.name		= "trace_clk_div_ck",
 	.parent		= &pmd_trace_clk_mux_ck,
+	.clkdm_name	= "emu_sys_clkdm",
 	.clksel		= trace_clk_div_div,
 	.clksel_reg	= OMAP4430_CM_EMU_DEBUGSS_CLKCTRL,
 	.clksel_mask	= OMAP4430_CLKSEL_PMD_TRACE_CLK_MASK,
@@ -3412,9 +3417,12 @@ int __init omap4xxx_clk_init(void)
 	if (cpu_is_omap443x()) {
 		cpu_mask = RATE_IN_4430;
 		cpu_clkflg = CK_443X;
-	} else if (cpu_is_omap446x()) {
+	} else if (cpu_is_omap446x() || cpu_is_omap447x()) {
 		cpu_mask = RATE_IN_4460 | RATE_IN_4430;
 		cpu_clkflg = CK_446X | CK_443X;
+
+		if (cpu_is_omap447x())
+			pr_warn("WARNING: OMAP4470 clock data incomplete!\n");
 	} else {
 		return 0;
 	}

arch/arm/mach-omap2/cm.h

@@ -22,4 +22,15 @@
  */
 #define MAX_MODULE_READY_TIME		2000
 
+/*
+ * MAX_MODULE_DISABLE_TIME: max duration in microseconds to wait for
+ * the PRCM to request that a module enter the inactive state in the
+ * case of OMAP2 & 3.  In the case of OMAP4 this is the max duration
+ * in microseconds for the module to reach the inactive state from
+ * a functional state.
+ * XXX FSUSB on OMAP4430 takes ~4ms to idle after reset during
+ * kernel init.
+ */
+#define MAX_MODULE_DISABLE_TIME		5000
+
 #endif

arch/arm/mach-omap2/cminst44xx.c

@@ -313,9 +313,9 @@ int omap4_cminst_wait_module_idle(u8 part, u16 inst, s16 cdoffs, u16 clkctrl_off
 
 	omap_test_timeout((_clkctrl_idlest(part, inst, cdoffs, clkctrl_offs) ==
 			   CLKCTRL_IDLEST_DISABLED),
-			  MAX_MODULE_READY_TIME, i);
+			  MAX_MODULE_DISABLE_TIME, i);
 
-	return (i < MAX_MODULE_READY_TIME) ? 0 : -EBUSY;
+	return (i < MAX_MODULE_DISABLE_TIME) ? 0 : -EBUSY;
 }
 
 /**

arch/arm/mach-omap2/mux.c

@@ -41,6 +41,7 @@
 #include "control.h"
 #include "mux.h"
 #include "prm.h"
+#include "common.h"
 
 #define OMAP_MUX_BASE_OFFSET		0x30	/* Offset from CTRL_BASE */
 #define OMAP_MUX_BASE_SZ		0x5ca

arch/arm/mach-omap2/omap_hwmod.c

@@ -530,7 +530,7 @@ static int _disable_wakeup(struct omap_hwmod *oh, u32 *v)
 	if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP)
 		_set_slave_idlemode(oh, HWMOD_IDLEMODE_SMART, v);
 	if (oh->class->sysc->idlemodes & MSTANDBY_SMART_WKUP)
-		_set_master_standbymode(oh, HWMOD_IDLEMODE_SMART_WKUP, v);
+		_set_master_standbymode(oh, HWMOD_IDLEMODE_SMART, v);
 
 	/* XXX test pwrdm_get_wken for this hwmod's subsystem */
 

arch/arm/mach-omap2/omap_hwmod_44xx_data.c

@@ -393,8 +393,7 @@ static struct omap_hwmod_class_sysconfig omap44xx_counter_sysc = {
 	.rev_offs	= 0x0000,
 	.sysc_offs	= 0x0004,
 	.sysc_flags	= SYSC_HAS_SIDLEMODE,
-	.idlemodes	= (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
-			   SIDLE_SMART_WKUP),
+	.idlemodes	= (SIDLE_FORCE | SIDLE_NO),
 	.sysc_fields	= &omap_hwmod_sysc_type1,
 };
 
@@ -854,6 +853,11 @@ static struct omap_hwmod omap44xx_dss_hdmi_hwmod = {
 	.name		= "dss_hdmi",
 	.class		= &omap44xx_hdmi_hwmod_class,
 	.clkdm_name	= "l3_dss_clkdm",
+	/*
+	 * HDMI audio requires to use no-idle mode. Hence,
+	 * set idle mode by software.
+	 */
+	.flags		= HWMOD_SWSUP_SIDLE,
 	.mpu_irqs	= omap44xx_dss_hdmi_irqs,
 	.sdma_reqs	= omap44xx_dss_hdmi_sdma_reqs,
 	.main_clk	= "dss_48mhz_clk",
@@ -1924,7 +1928,7 @@ static struct omap_hwmod_dma_info omap44xx_mcbsp1_sdma_reqs[] = {
 
 static struct omap_hwmod_opt_clk mcbsp1_opt_clks[] = {
 	{ .role = "pad_fck", .clk = "pad_clks_ck" },
-	{ .role = "prcm_clk", .clk = "mcbsp1_sync_mux_ck" },
+	{ .role = "prcm_fck", .clk = "mcbsp1_sync_mux_ck" },
 };
 
 static struct omap_hwmod omap44xx_mcbsp1_hwmod = {
@@ -1959,7 +1963,7 @@ static struct omap_hwmod_dma_info omap44xx_mcbsp2_sdma_reqs[] = {
 
 static struct omap_hwmod_opt_clk mcbsp2_opt_clks[] = {
 	{ .role = "pad_fck", .clk = "pad_clks_ck" },
-	{ .role = "prcm_clk", .clk = "mcbsp2_sync_mux_ck" },
+	{ .role = "prcm_fck", .clk = "mcbsp2_sync_mux_ck" },
 };
 
 static struct omap_hwmod omap44xx_mcbsp2_hwmod = {
@@ -1994,7 +1998,7 @@ static struct omap_hwmod_dma_info omap44xx_mcbsp3_sdma_reqs[] = {
 
 static struct omap_hwmod_opt_clk mcbsp3_opt_clks[] = {
 	{ .role = "pad_fck", .clk = "pad_clks_ck" },
-	{ .role = "prcm_clk", .clk = "mcbsp3_sync_mux_ck" },
+	{ .role = "prcm_fck", .clk = "mcbsp3_sync_mux_ck" },
 };
 
 static struct omap_hwmod omap44xx_mcbsp3_hwmod = {
@@ -2029,7 +2033,7 @@ static struct omap_hwmod_dma_info omap44xx_mcbsp4_sdma_reqs[] = {
 
 static struct omap_hwmod_opt_clk mcbsp4_opt_clks[] = {
 	{ .role = "pad_fck", .clk = "pad_clks_ck" },
-	{ .role = "prcm_clk", .clk = "mcbsp4_sync_mux_ck" },
+	{ .role = "prcm_fck", .clk = "mcbsp4_sync_mux_ck" },
 };
 
 static struct omap_hwmod omap44xx_mcbsp4_hwmod = {
@@ -3860,7 +3864,7 @@ static struct omap_hwmod_ocp_if omap44xx_l4_cfg__l3_main_2 = {
 };
 
 /* usb_host_fs -> l3_main_2 */
-static struct omap_hwmod_ocp_if omap44xx_usb_host_fs__l3_main_2 = {
+static struct omap_hwmod_ocp_if __maybe_unused omap44xx_usb_host_fs__l3_main_2 = {
 	.master		= &omap44xx_usb_host_fs_hwmod,
 	.slave		= &omap44xx_l3_main_2_hwmod,
 	.clk		= "l3_div_ck",
@@ -3918,7 +3922,7 @@ static struct omap_hwmod_ocp_if omap44xx_l4_cfg__l3_main_3 = {
 };
 
 /* aess -> l4_abe */
-static struct omap_hwmod_ocp_if omap44xx_aess__l4_abe = {
+static struct omap_hwmod_ocp_if __maybe_unused omap44xx_aess__l4_abe = {
 	.master		= &omap44xx_aess_hwmod,
 	.slave		= &omap44xx_l4_abe_hwmod,
 	.clk		= "ocp_abe_iclk",
@@ -4009,7 +4013,7 @@ static struct omap_hwmod_addr_space omap44xx_aess_addrs[] = {
 };
 
 /* l4_abe -> aess */
-static struct omap_hwmod_ocp_if omap44xx_l4_abe__aess = {
+static struct omap_hwmod_ocp_if __maybe_unused omap44xx_l4_abe__aess = {
 	.master		= &omap44xx_l4_abe_hwmod,
 	.slave		= &omap44xx_aess_hwmod,
 	.clk		= "ocp_abe_iclk",
@@ -4027,7 +4031,7 @@ static struct omap_hwmod_addr_space omap44xx_aess_dma_addrs[] = {
 };
 
 /* l4_abe -> aess (dma) */
-static struct omap_hwmod_ocp_if omap44xx_l4_abe__aess_dma = {
+static struct omap_hwmod_ocp_if __maybe_unused omap44xx_l4_abe__aess_dma = {
 	.master		= &omap44xx_l4_abe_hwmod,
 	.slave		= &omap44xx_aess_hwmod,
 	.clk		= "ocp_abe_iclk",
@@ -5853,7 +5857,7 @@ static struct omap_hwmod_addr_space omap44xx_usb_host_fs_addrs[] = {
 };
 
 /* l4_cfg -> usb_host_fs */
-static struct omap_hwmod_ocp_if omap44xx_l4_cfg__usb_host_fs = {
+static struct omap_hwmod_ocp_if __maybe_unused omap44xx_l4_cfg__usb_host_fs = {
 	.master		= &omap44xx_l4_cfg_hwmod,
 	.slave		= &omap44xx_usb_host_fs_hwmod,
 	.clk		= "l4_div_ck",
@@ -6010,13 +6014,13 @@ static struct omap_hwmod_ocp_if *omap44xx_hwmod_ocp_ifs[] __initdata = {
 	&omap44xx_iva__l3_main_2,
 	&omap44xx_l3_main_1__l3_main_2,
 	&omap44xx_l4_cfg__l3_main_2,
-	&omap44xx_usb_host_fs__l3_main_2,
+	/* &omap44xx_usb_host_fs__l3_main_2, */
 	&omap44xx_usb_host_hs__l3_main_2,
 	&omap44xx_usb_otg_hs__l3_main_2,
 	&omap44xx_l3_main_1__l3_main_3,
 	&omap44xx_l3_main_2__l3_main_3,
 	&omap44xx_l4_cfg__l3_main_3,
-	&omap44xx_aess__l4_abe,
+	/* &omap44xx_aess__l4_abe, */
 	&omap44xx_dsp__l4_abe,
 	&omap44xx_l3_main_1__l4_abe,
 	&omap44xx_mpu__l4_abe,
@@ -6025,8 +6029,8 @@ static struct omap_hwmod_ocp_if *omap44xx_hwmod_ocp_ifs[] __initdata = {
 	&omap44xx_l4_cfg__l4_wkup,
 	&omap44xx_mpu__mpu_private,
 	&omap44xx_l4_cfg__ocp_wp_noc,
-	&omap44xx_l4_abe__aess,
-	&omap44xx_l4_abe__aess_dma,
+	/* &omap44xx_l4_abe__aess, */
+	/* &omap44xx_l4_abe__aess_dma, */
 	&omap44xx_l3_main_2__c2c,
 	&omap44xx_l4_wkup__counter_32k,
 	&omap44xx_l4_cfg__ctrl_module_core,
@@ -6132,7 +6136,7 @@ static struct omap_hwmod_ocp_if *omap44xx_hwmod_ocp_ifs[] __initdata = {
 	&omap44xx_l4_per__uart2,
 	&omap44xx_l4_per__uart3,
 	&omap44xx_l4_per__uart4,
-	&omap44xx_l4_cfg__usb_host_fs,
+	/* &omap44xx_l4_cfg__usb_host_fs, */
 	&omap44xx_l4_cfg__usb_host_hs,
 	&omap44xx_l4_cfg__usb_otg_hs,
 	&omap44xx_l4_cfg__usb_tll_hs,

arch/arm/mach-omap2/omap_phy_internal.c

@@ -239,21 +239,15 @@ void am35x_set_mode(u8 musb_mode)
 
 	devconf2 &= ~CONF2_OTGMODE;
 	switch (musb_mode) {
-#ifdef	CONFIG_USB_MUSB_HDRC_HCD
 	case MUSB_HOST:		/* Force VBUS valid, ID = 0 */
 		devconf2 |= CONF2_FORCE_HOST;
 		break;
-#endif
-#ifdef	CONFIG_USB_GADGET_MUSB_HDRC
 	case MUSB_PERIPHERAL:	/* Force VBUS valid, ID = 1 */
 		devconf2 |= CONF2_FORCE_DEVICE;
 		break;
-#endif
-#ifdef	CONFIG_USB_MUSB_OTG
 	case MUSB_OTG:		/* Don't override the VBUS/ID comparators */
 		devconf2 |= CONF2_NO_OVERRIDE;
 		break;
-#endif
 	default:
 		pr_info(KERN_INFO "Unsupported mode %u\n", musb_mode);
 	}

arch/arm/mach-omap2/twl-common.c

@@ -32,6 +32,7 @@
 #include "twl-common.h"
 #include "pm.h"
 #include "voltage.h"
+#include "mux.h"
 
 static struct i2c_board_info __initdata pmic_i2c_board_info = {
 	.addr		= 0x48,
@@ -77,6 +78,7 @@ void __init omap4_pmic_init(const char *pmic_type,
 		    struct twl6040_platform_data *twl6040_data, int twl6040_irq)
 {
 	/* PMIC part*/
+	omap_mux_init_signal("sys_nirq1", OMAP_PIN_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE);
 	strncpy(omap4_i2c1_board_info[0].type, pmic_type,
 		sizeof(omap4_i2c1_board_info[0].type));
 	omap4_i2c1_board_info[0].irq = OMAP44XX_IRQ_SYS_1N;

arch/arm/mach-omap2/usb-musb.c

@@ -41,12 +41,10 @@ static struct musb_hdrc_config musb_config = {
 };
 
 static struct musb_hdrc_platform_data musb_plat = {
-#ifdef CONFIG_USB_MUSB_OTG
+#ifdef CONFIG_USB_GADGET_MUSB_HDRC
 	.mode		= MUSB_OTG,
-#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
+#else
 	.mode		= MUSB_HOST,
-#elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
-	.mode		= MUSB_PERIPHERAL,
 #endif
 	/* .clock is set dynamically */
 	.config		= &musb_config,

arch/arm/mach-omap2/usb-tusb6010.c

@@ -300,7 +300,7 @@ tusb6010_setup_interface(struct musb_hdrc_platform_data *data,
 		printk(error, 3, status);
 		return status;
 	}
-	tusb_resources[2].start = irq + IH_GPIO_BASE;
+	tusb_resources[2].start = gpio_to_irq(irq);
 
 	/* set up memory timings ... can speed them up later */
 	if (!ps_refclk) {

arch/arm/mach-orion5x/include/mach/bridge-regs.h

@@ -35,5 +35,5 @@
 #define MAIN_IRQ_MASK		(ORION5X_BRIDGE_VIRT_BASE | 0x204)
 
 #define TIMER_VIRT_BASE		(ORION5X_BRIDGE_VIRT_BASE | 0x300)
-
+#define TIMER_PHYS_BASE		(ORION5X_BRIDGE_PHYS_BASE | 0x300)
 #endif

arch/arm/mach-orion5x/include/mach/io.h

@@ -0,0 +1,22 @@
+/*
+ * arch/arm/mach-orion5x/include/mach/io.h
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#ifndef __ASM_ARCH_IO_H
+#define __ASM_ARCH_IO_H
+
+#include <mach/orion5x.h>
+#include <asm/sizes.h>
+
+#define IO_SPACE_LIMIT		SZ_2M
+static inline void __iomem *__io(unsigned long addr)
+{
+	return (void __iomem *)(addr + ORION5X_PCIE_IO_VIRT_BASE);
+}
+
+#define __io(a)			 __io(a)
+#endif

arch/arm/mach-orion5x/include/mach/orion5x.h

@@ -82,6 +82,7 @@
 #define  UART1_VIRT_BASE		(ORION5X_DEV_BUS_VIRT_BASE | 0x2100)
 
 #define ORION5X_BRIDGE_VIRT_BASE	(ORION5X_REGS_VIRT_BASE | 0x20000)
+#define ORION5X_BRIDGE_PHYS_BASE	(ORION5X_REGS_PHYS_BASE | 0x20000)
 
 #define ORION5X_PCI_VIRT_BASE		(ORION5X_REGS_VIRT_BASE | 0x30000)
 

arch/arm/mach-pxa/hx4700.c

@@ -127,7 +127,11 @@ static unsigned long hx4700_pin_config[] __initdata = {
 	GPIO19_SSP2_SCLK,
 	GPIO86_SSP2_RXD,
 	GPIO87_SSP2_TXD,
-	GPIO88_GPIO,
+	GPIO88_GPIO | MFP_LPM_DRIVE_HIGH,	/* TSC2046_CS */
+
+	/* BQ24022 Regulator */
+	GPIO72_GPIO | MFP_LPM_KEEP_OUTPUT,	/* BQ24022_nCHARGE_EN */
+	GPIO96_GPIO | MFP_LPM_KEEP_OUTPUT,	/* BQ24022_ISET2 */
 
 	/* HX4700 specific input GPIOs */
 	GPIO12_GPIO | WAKEUP_ON_EDGE_RISE,	/* ASIC3_IRQ */
@@ -135,6 +139,10 @@ static unsigned long hx4700_pin_config[] __initdata = {
 	GPIO14_GPIO,	/* nWLAN_IRQ */
 
 	/* HX4700 specific output GPIOs */
+	GPIO61_GPIO | MFP_LPM_DRIVE_HIGH,	/* W3220_nRESET */
+	GPIO71_GPIO | MFP_LPM_DRIVE_HIGH,	/* ASIC3_nRESET */
+	GPIO81_GPIO | MFP_LPM_DRIVE_HIGH,	/* CPU_GP_nRESET */
+	GPIO116_GPIO | MFP_LPM_DRIVE_HIGH,	/* CPU_HW_nRESET */
 	GPIO102_GPIO | MFP_LPM_DRIVE_LOW,	/* SYNAPTICS_POWER_ON */
 
 	GPIO10_GPIO,	/* GSM_IRQ */
@@ -872,14 +880,19 @@ static struct gpio global_gpios[] = {
 	{ GPIO110_HX4700_LCD_LVDD_3V3_ON, GPIOF_OUT_INIT_HIGH, "LCD_LVDD" },
 	{ GPIO111_HX4700_LCD_AVDD_3V3_ON, GPIOF_OUT_INIT_HIGH, "LCD_AVDD" },
 	{ GPIO32_HX4700_RS232_ON,         GPIOF_OUT_INIT_HIGH, "RS232_ON" },
+	{ GPIO61_HX4700_W3220_nRESET,     GPIOF_OUT_INIT_HIGH, "W3220_nRESET" },
 	{ GPIO71_HX4700_ASIC3_nRESET,     GPIOF_OUT_INIT_HIGH, "ASIC3_nRESET" },
+	{ GPIO81_HX4700_CPU_GP_nRESET,    GPIOF_OUT_INIT_HIGH, "CPU_GP_nRESET" },
 	{ GPIO82_HX4700_EUART_RESET,      GPIOF_OUT_INIT_HIGH, "EUART_RESET" },
+	{ GPIO116_HX4700_CPU_HW_nRESET,   GPIOF_OUT_INIT_HIGH, "CPU_HW_nRESET" },
 };
 
 static void __init hx4700_init(void)
 {
 	int ret;
 
+	PCFR = PCFR_GPR_EN | PCFR_OPDE;
+
 	pxa2xx_mfp_config(ARRAY_AND_SIZE(hx4700_pin_config));
 	gpio_set_wake(GPIO12_HX4700_ASIC3_IRQ, 1);
 	ret = gpio_request_array(ARRAY_AND_SIZE(global_gpios));

arch/arm/mach-shmobile/board-armadillo800eva.c

@@ -779,6 +779,7 @@ DT_MACHINE_START(ARMADILLO800EVA_DT, "armadillo800eva")
 	.init_irq	= r8a7740_init_irq,
 	.handle_irq	= shmobile_handle_irq_intc,
 	.init_machine	= eva_init,
+	.init_late	= shmobile_init_late,
 	.timer		= &shmobile_timer,
 	.dt_compat	= eva_boards_compat_dt,
 MACHINE_END

arch/arm/mach-shmobile/board-kzm9d.c

@@ -80,6 +80,7 @@ DT_MACHINE_START(KZM9D_DT, "kzm9d")
 	.init_irq	= emev2_init_irq,
 	.handle_irq	= gic_handle_irq,
 	.init_machine	= kzm9d_add_standard_devices,
+	.init_late	= shmobile_init_late,
 	.timer		= &shmobile_timer,
 	.dt_compat	= kzm9d_boards_compat_dt,
 MACHINE_END

arch/arm/mach-shmobile/board-kzm9g.c

@@ -455,6 +455,7 @@ DT_MACHINE_START(KZM9G_DT, "kzm9g")
 	.init_irq	= sh73a0_init_irq,
 	.handle_irq	= gic_handle_irq,
 	.init_machine	= kzm_init,
+	.init_late	= shmobile_init_late,
 	.timer		= &shmobile_timer,
 	.dt_compat	= kzm9g_boards_compat_dt,
 MACHINE_END

arch/arm/mach-shmobile/board-mackerel.c

@@ -1512,6 +1512,9 @@ static void __init mackerel_init(void)
 	gpio_request(GPIO_FN_SDHID0_1, NULL);
 	gpio_request(GPIO_FN_SDHID0_0, NULL);
 
+	/* SDHI0 PORT172 card-detect IRQ26 */
+	gpio_request(GPIO_FN_IRQ26_172, NULL);
+
 #if !defined(CONFIG_MMC_SH_MMCIF) && !defined(CONFIG_MMC_SH_MMCIF_MODULE)
 	/* enable SDHI1 */
 	gpio_request(GPIO_FN_SDHICMD1, NULL);

arch/arm/mach-shmobile/clock-sh73a0.c

@@ -475,9 +475,9 @@ static struct clk *late_main_clks[] = {
 
 enum { MSTP001,
 	MSTP129, MSTP128, MSTP127, MSTP126, MSTP125, MSTP118, MSTP116, MSTP100,
-	MSTP219,
+	MSTP219, MSTP218,
 	MSTP207, MSTP206, MSTP204, MSTP203, MSTP202, MSTP201, MSTP200,
-	MSTP331, MSTP329, MSTP325, MSTP323, MSTP318,
+	MSTP331, MSTP329, MSTP325, MSTP323,
 	MSTP314, MSTP313, MSTP312, MSTP311,
 	MSTP303, MSTP302, MSTP301, MSTP300,
 	MSTP411, MSTP410, MSTP403,
@@ -497,6 +497,7 @@ static struct clk mstp_clks[MSTP_NR] = {
 	[MSTP116] = MSTP(&div4_clks[DIV4_HP], SMSTPCR1, 16, 0), /* IIC0 */
 	[MSTP100] = MSTP(&div4_clks[DIV4_B], SMSTPCR1, 0, 0), /* LCDC0 */
 	[MSTP219] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 19, 0), /* SCIFA7 */
+	[MSTP218] = MSTP(&div4_clks[DIV4_HP], SMSTPCR2, 18, 0), /* SY-DMAC */
 	[MSTP207] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 7, 0), /* SCIFA5 */
 	[MSTP206] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 6, 0), /* SCIFB */
 	[MSTP204] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR2, 4, 0), /* SCIFA0 */
@@ -508,7 +509,6 @@ static struct clk mstp_clks[MSTP_NR] = {
 	[MSTP329] = MSTP(&r_clk, SMSTPCR3, 29, 0), /* CMT10 */
 	[MSTP325] = MSTP(&div6_clks[DIV6_SUB], SMSTPCR3, 25, 0), /* IrDA */
 	[MSTP323] = MSTP(&div4_clks[DIV4_HP], SMSTPCR3, 23, 0), /* IIC1 */
-	[MSTP318] = MSTP(&div4_clks[DIV4_HP], SMSTPCR3, 18, 0), /* SY-DMAC */
 	[MSTP314] = MSTP(&div6_clks[DIV6_SDHI0], SMSTPCR3, 14, 0), /* SDHI0 */
 	[MSTP313] = MSTP(&div6_clks[DIV6_SDHI1], SMSTPCR3, 13, 0), /* SDHI1 */
 	[MSTP312] = MSTP(&div4_clks[DIV4_HP], SMSTPCR3, 12, 0), /* MMCIF0 */
@@ -552,6 +552,7 @@ static struct clk_lookup lookups[] = {
 	CLKDEV_DEV_ID("i2c-sh_mobile.0", &mstp_clks[MSTP116]), /* I2C0 */
 	CLKDEV_DEV_ID("sh_mobile_lcdc_fb.0", &mstp_clks[MSTP100]), /* LCDC0 */
 	CLKDEV_DEV_ID("sh-sci.7", &mstp_clks[MSTP219]), /* SCIFA7 */
+	CLKDEV_DEV_ID("sh-dma-engine.0", &mstp_clks[MSTP218]), /* SY-DMAC */
 	CLKDEV_DEV_ID("sh-sci.5", &mstp_clks[MSTP207]), /* SCIFA5 */
 	CLKDEV_DEV_ID("sh-sci.8", &mstp_clks[MSTP206]), /* SCIFB */
 	CLKDEV_DEV_ID("sh-sci.0", &mstp_clks[MSTP204]), /* SCIFA0 */
@@ -563,7 +564,6 @@ static struct clk_lookup lookups[] = {
 	CLKDEV_DEV_ID("sh_cmt.10", &mstp_clks[MSTP329]), /* CMT10 */
 	CLKDEV_DEV_ID("sh_irda.0", &mstp_clks[MSTP325]), /* IrDA */
 	CLKDEV_DEV_ID("i2c-sh_mobile.1", &mstp_clks[MSTP323]), /* I2C1 */
-	CLKDEV_DEV_ID("sh-dma-engine.0", &mstp_clks[MSTP318]), /* SY-DMAC */
 	CLKDEV_DEV_ID("sh_mobile_sdhi.0", &mstp_clks[MSTP314]), /* SDHI0 */
 	CLKDEV_DEV_ID("sh_mobile_sdhi.1", &mstp_clks[MSTP313]), /* SDHI1 */
 	CLKDEV_DEV_ID("sh_mmcif.0", &mstp_clks[MSTP312]), /* MMCIF0 */

arch/arm/mach-shmobile/intc-r8a7779.c

@@ -35,6 +35,9 @@
 #define INT2SMSKCR3 0xfe7822ac
 #define INT2SMSKCR4 0xfe7822b0
 
+#define INT2NTSR0 0xfe700060
+#define INT2NTSR1 0xfe700064
+
 static int r8a7779_set_wake(struct irq_data *data, unsigned int on)
 {
 	return 0; /* always allow wakeup */
@@ -49,6 +52,10 @@ void __init r8a7779_init_irq(void)
 	gic_init(0, 29, gic_dist_base, gic_cpu_base);
 	gic_arch_extn.irq_set_wake = r8a7779_set_wake;
 
+	/* route all interrupts to ARM */
+	__raw_writel(0xffffffff, INT2NTSR0);
+	__raw_writel(0x3fffffff, INT2NTSR1);
+
 	/* unmask all known interrupts in INTCS2 */
 	__raw_writel(0xfffffff0, INT2SMSKCR0);
 	__raw_writel(0xfff7ffff, INT2SMSKCR1);

arch/arm/mach-shmobile/platsmp.c

@@ -25,7 +25,12 @@
 #define is_sh73a0() (machine_is_ag5evm() || machine_is_kota2() || \
 			of_machine_is_compatible("renesas,sh73a0"))
 #define is_r8a7779() machine_is_marzen()
+
+#ifdef CONFIG_ARCH_EMEV2
 #define is_emev2() of_machine_is_compatible("renesas,emev2")
+#else
+#define is_emev2() (0)
+#endif
 
 static unsigned int __init shmobile_smp_get_core_count(void)
 {

arch/arm/mach-shmobile/setup-sh7372.c

@@ -484,7 +484,7 @@ static const struct sh_dmae_slave_config sh7372_dmae_slaves[] = {
 	},
 };
 
-#define SH7372_CHCLR 0x220
+#define SH7372_CHCLR (0x220 - 0x20)
 
 static const struct sh_dmae_channel sh7372_dmae_channels[] = {
 	{

arch/arm/mach-spear13xx/include/mach/debug-macro.S

@@ -4,7 +4,7 @@
  * Debugging macro include header spear13xx machine family
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/include/mach/dma.h

@@ -4,7 +4,7 @@
  * DMA information for SPEAr13xx machine family
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/include/mach/generic.h

@@ -4,7 +4,7 @@
  * spear13xx machine family generic header file
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/include/mach/gpio.h

@@ -4,7 +4,7 @@
  * GPIO macros for SPEAr13xx machine family
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/include/mach/irqs.h

@@ -4,7 +4,7 @@
  * IRQ helper macros for spear13xx machine family
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/include/mach/spear.h

@@ -4,7 +4,7 @@
  * spear13xx Machine family specific definition
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/include/mach/timex.h

@@ -4,7 +4,7 @@
  * SPEAr3XX machine family specific timex definitions
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/include/mach/uncompress.h

@@ -4,7 +4,7 @@
  * Serial port stubs for kernel decompress status messages
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/spear1310.c

@@ -4,7 +4,7 @@
  * SPEAr1310 machine source file
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/spear1340.c

@@ -4,7 +4,7 @@
  * SPEAr1340 machine source file
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear13xx/spear13xx.c

@@ -4,7 +4,7 @@
  * SPEAr13XX machines common source file
  *
  * Copyright (C) 2012 ST Microelectronics
- * Viresh Kumar <viresh.kumar@st.com>
+ * Viresh Kumar <viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any

arch/arm/mach-spear3xx/include/mach/debug-macro.S

@@ -4,7 +4,7 @@
  * Debugging macro include header spear3xx machine family
  *
  * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar<viresh.kumar@st.com>
+ * Viresh Kumar<viresh.linux@gmail.com>
  *
  * This file is licensed under the terms of the GNU General Public
  * License version 2. This program is licensed "as is" without any