serial: stm32-usart: Add STM32 USART Driver

This drivers adds support to the STM32 USART controller, which is a
standard serial driver.

Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/Kconfig

@@ -1608,6 +1608,23 @@ config SERIAL_SPRD_CONSOLE
 	  with "earlycon" on the kernel command line. The console is
 	  enabled when early_param is processed.
 
+config SERIAL_STM32
+	tristate "STMicroelectronics STM32 serial port support"
+	select SERIAL_CORE
+	depends on ARM || COMPILE_TEST
+	help
+	  This driver is for the on-chip Serial Controller on
+	  STMicroelectronics STM32 MCUs.
+	  USART supports Rx & Tx functionality.
+	  It support all industry standard baud rates.
+
+	  If unsure, say N.
+
+config SERIAL_STM32_CONSOLE
+	bool "Support for console on STM32"
+	depends on SERIAL_STM32=y
+	select SERIAL_CORE_CONSOLE
+
 endmenu
 
 config SERIAL_MCTRL_GPIO

drivers/tty/serial/Makefile

@@ -92,6 +92,7 @@ obj-$(CONFIG_SERIAL_FSL_LPUART)	+= fsl_lpuart.o
 obj-$(CONFIG_SERIAL_CONEXANT_DIGICOLOR)	+= digicolor-usart.o
 obj-$(CONFIG_SERIAL_MEN_Z135)	+= men_z135_uart.o
 obj-$(CONFIG_SERIAL_SPRD) += sprd_serial.o
+obj-$(CONFIG_SERIAL_STM32)	+= stm32-usart.o
 
 # GPIOLIB helpers for modem control lines
 obj-$(CONFIG_SERIAL_MCTRL_GPIO)	+= serial_mctrl_gpio.o

drivers/tty/serial/stm32-usart.c

@@ -0,0 +1,739 @@
+/*
+ * Copyright (C) Maxime Coquelin 2015
+ * Author:  Maxime Coquelin <mcoquelin.stm32@gmail.com>
+ * License terms:  GNU General Public License (GPL), version 2
+ *
+ * Inspired by st-asc.c from STMicroelectronics (c)
+ */
+
+#if defined(CONFIG_SERIAL_STM32_USART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/serial.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/delay.h>
+#include <linux/spinlock.h>
+#include <linux/pm_runtime.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/serial_core.h>
+#include <linux/clk.h>
+
+#define DRIVER_NAME "stm32-usart"
+
+/* Register offsets */
+#define USART_SR		0x00
+#define USART_DR		0x04
+#define USART_BRR		0x08
+#define USART_CR1		0x0c
+#define USART_CR2		0x10
+#define USART_CR3		0x14
+#define USART_GTPR		0x18
+
+/* USART_SR */
+#define USART_SR_PE		BIT(0)
+#define USART_SR_FE		BIT(1)
+#define USART_SR_NF		BIT(2)
+#define USART_SR_ORE		BIT(3)
+#define USART_SR_IDLE		BIT(4)
+#define USART_SR_RXNE		BIT(5)
+#define USART_SR_TC		BIT(6)
+#define USART_SR_TXE		BIT(7)
+#define USART_SR_LBD		BIT(8)
+#define USART_SR_CTS		BIT(9)
+#define USART_SR_ERR_MASK	(USART_SR_LBD | USART_SR_ORE | \
+				 USART_SR_FE | USART_SR_PE)
+/* Dummy bits */
+#define USART_SR_DUMMY_RX	BIT(16)
+
+/* USART_DR */
+#define USART_DR_MASK		GENMASK(8, 0)
+
+/* USART_BRR */
+#define USART_BRR_DIV_F_MASK	GENMASK(3, 0)
+#define USART_BRR_DIV_M_MASK	GENMASK(15, 4)
+#define USART_BRR_DIV_M_SHIFT	4
+
+/* USART_CR1 */
+#define USART_CR1_SBK		BIT(0)
+#define USART_CR1_RWU		BIT(1)
+#define USART_CR1_RE		BIT(2)
+#define USART_CR1_TE		BIT(3)
+#define USART_CR1_IDLEIE	BIT(4)
+#define USART_CR1_RXNEIE	BIT(5)
+#define USART_CR1_TCIE		BIT(6)
+#define USART_CR1_TXEIE		BIT(7)
+#define USART_CR1_PEIE		BIT(8)
+#define USART_CR1_PS		BIT(9)
+#define USART_CR1_PCE		BIT(10)
+#define USART_CR1_WAKE		BIT(11)
+#define USART_CR1_M		BIT(12)
+#define USART_CR1_UE		BIT(13)
+#define USART_CR1_OVER8		BIT(15)
+#define USART_CR1_IE_MASK	GENMASK(8, 4)
+
+/* USART_CR2 */
+#define USART_CR2_ADD_MASK	GENMASK(3, 0)
+#define USART_CR2_LBDL		BIT(5)
+#define USART_CR2_LBDIE		BIT(6)
+#define USART_CR2_LBCL		BIT(8)
+#define USART_CR2_CPHA		BIT(9)
+#define USART_CR2_CPOL		BIT(10)
+#define USART_CR2_CLKEN		BIT(11)
+#define USART_CR2_STOP_2B	BIT(13)
+#define USART_CR2_STOP_MASK	GENMASK(13, 12)
+#define USART_CR2_LINEN		BIT(14)
+
+/* USART_CR3 */
+#define USART_CR3_EIE		BIT(0)
+#define USART_CR3_IREN		BIT(1)
+#define USART_CR3_IRLP		BIT(2)
+#define USART_CR3_HDSEL		BIT(3)
+#define USART_CR3_NACK		BIT(4)
+#define USART_CR3_SCEN		BIT(5)
+#define USART_CR3_DMAR		BIT(6)
+#define USART_CR3_DMAT		BIT(7)
+#define USART_CR3_RTSE		BIT(8)
+#define USART_CR3_CTSE		BIT(9)
+#define USART_CR3_CTSIE		BIT(10)
+#define USART_CR3_ONEBIT	BIT(11)
+
+/* USART_GTPR */
+#define USART_GTPR_PSC_MASK	GENMASK(7, 0)
+#define USART_GTPR_GT_MASK	GENMASK(15, 8)
+
+#define DRIVER_NAME "stm32-usart"
+#define STM32_SERIAL_NAME "ttyS"
+#define STM32_MAX_PORTS 6
+
+struct stm32_port {
+	struct uart_port port;
+	struct clk *clk;
+	bool hw_flow_control;
+};
+
+static struct stm32_port stm32_ports[STM32_MAX_PORTS];
+static struct uart_driver stm32_usart_driver;
+
+static void stm32_stop_tx(struct uart_port *port);
+
+static inline struct stm32_port *to_stm32_port(struct uart_port *port)
+{
+	return container_of(port, struct stm32_port, port);
+}
+
+static void stm32_set_bits(struct uart_port *port, u32 reg, u32 bits)
+{
+	u32 val;
+
+	val = readl_relaxed(port->membase + reg);
+	val |= bits;
+	writel_relaxed(val, port->membase + reg);
+}
+
+static void stm32_clr_bits(struct uart_port *port, u32 reg, u32 bits)
+{
+	u32 val;
+
+	val = readl_relaxed(port->membase + reg);
+	val &= ~bits;
+	writel_relaxed(val, port->membase + reg);
+}
+
+static void stm32_receive_chars(struct uart_port *port)
+{
+	struct tty_port *tport = &port->state->port;
+	unsigned long c;
+	u32 sr;
+	char flag;
+
+	if (port->irq_wake)
+		pm_wakeup_event(tport->tty->dev, 0);
+
+	while ((sr = readl_relaxed(port->membase + USART_SR)) & USART_SR_RXNE) {
+		sr |= USART_SR_DUMMY_RX;
+		c = readl_relaxed(port->membase + USART_DR);
+		flag = TTY_NORMAL;
+		port->icount.rx++;
+
+		if (sr & USART_SR_ERR_MASK) {
+			if (sr & USART_SR_LBD) {
+				port->icount.brk++;
+				if (uart_handle_break(port))
+					continue;
+			} else if (sr & USART_SR_ORE) {
+				port->icount.overrun++;
+			} else if (sr & USART_SR_PE) {
+				port->icount.parity++;
+			} else if (sr & USART_SR_FE) {
+				port->icount.frame++;
+			}
+
+			sr &= port->read_status_mask;
+
+			if (sr & USART_SR_LBD)
+				flag = TTY_BREAK;
+			else if (sr & USART_SR_PE)
+				flag = TTY_PARITY;
+			else if (sr & USART_SR_FE)
+				flag = TTY_FRAME;
+		}
+
+		if (uart_handle_sysrq_char(port, c))
+			continue;
+		uart_insert_char(port, sr, USART_SR_ORE, c, flag);
+	}
+
+	spin_unlock(&port->lock);
+	tty_flip_buffer_push(tport);
+	spin_lock(&port->lock);
+}
+
+static void stm32_transmit_chars(struct uart_port *port)
+{
+	struct circ_buf *xmit = &port->state->xmit;
+
+	if (port->x_char) {
+		writel_relaxed(port->x_char, port->membase + USART_DR);
+		port->x_char = 0;
+		port->icount.tx++;
+		return;
+	}
+
+	if (uart_tx_stopped(port)) {
+		stm32_stop_tx(port);
+		return;
+	}
+
+	if (uart_circ_empty(xmit)) {
+		stm32_stop_tx(port);
+		return;
+	}
+
+	writel_relaxed(xmit->buf[xmit->tail], port->membase + USART_DR);
+	xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+	port->icount.tx++;
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(port);
+
+	if (uart_circ_empty(xmit))
+		stm32_stop_tx(port);
+}
+
+static irqreturn_t stm32_interrupt(int irq, void *ptr)
+{
+	struct uart_port *port = ptr;
+	u32 sr;
+
+	spin_lock(&port->lock);
+
+	sr = readl_relaxed(port->membase + USART_SR);
+
+	if (sr & USART_SR_RXNE)
+		stm32_receive_chars(port);
+
+	if (sr & USART_SR_TXE)
+		stm32_transmit_chars(port);
+
+	spin_unlock(&port->lock);
+
+	return IRQ_HANDLED;
+}
+
+static unsigned int stm32_tx_empty(struct uart_port *port)
+{
+	return readl_relaxed(port->membase + USART_SR) & USART_SR_TXE;
+}
+
+static void stm32_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS))
+		stm32_set_bits(port, USART_CR3, USART_CR3_RTSE);
+	else
+		stm32_clr_bits(port, USART_CR3, USART_CR3_RTSE);
+}
+
+static unsigned int stm32_get_mctrl(struct uart_port *port)
+{
+	/* This routine is used to get signals of: DCD, DSR, RI, and CTS */
+	return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
+}
+
+/* Transmit stop */
+static void stm32_stop_tx(struct uart_port *port)
+{
+	stm32_clr_bits(port, USART_CR1, USART_CR1_TXEIE);
+}
+
+/* There are probably characters waiting to be transmitted. */
+static void stm32_start_tx(struct uart_port *port)
+{
+	struct circ_buf *xmit = &port->state->xmit;
+
+	if (uart_circ_empty(xmit))
+		return;
+
+	stm32_set_bits(port, USART_CR1, USART_CR1_TXEIE | USART_CR1_TE);
+}
+
+/* Throttle the remote when input buffer is about to overflow. */
+static void stm32_throttle(struct uart_port *port)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->lock, flags);
+	stm32_clr_bits(port, USART_CR1, USART_CR1_RXNEIE);
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+/* Unthrottle the remote, the input buffer can now accept data. */
+static void stm32_unthrottle(struct uart_port *port)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&port->lock, flags);
+	stm32_set_bits(port, USART_CR1, USART_CR1_RXNEIE);
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+/* Receive stop */
+static void stm32_stop_rx(struct uart_port *port)
+{
+	stm32_clr_bits(port, USART_CR1, USART_CR1_RXNEIE);
+}
+
+/* Handle breaks - ignored by us */
+static void stm32_break_ctl(struct uart_port *port, int break_state)
+{
+}
+
+static int stm32_startup(struct uart_port *port)
+{
+	const char *name = to_platform_device(port->dev)->name;
+	u32 val;
+	int ret;
+
+	ret = request_irq(port->irq, stm32_interrupt, IRQF_NO_SUSPEND,
+			  name, port);
+	if (ret)
+		return ret;
+
+	val = USART_CR1_RXNEIE | USART_CR1_TE | USART_CR1_RE;
+	stm32_set_bits(port, USART_CR1, val);
+
+	return 0;
+}
+
+static void stm32_shutdown(struct uart_port *port)
+{
+	u32 val;
+
+	val = USART_CR1_TXEIE | USART_CR1_RXNEIE | USART_CR1_TE | USART_CR1_RE;
+	stm32_set_bits(port, USART_CR1, val);
+
+	free_irq(port->irq, port);
+}
+
+static void stm32_set_termios(struct uart_port *port, struct ktermios *termios,
+			    struct ktermios *old)
+{
+	struct stm32_port *stm32_port = to_stm32_port(port);
+	unsigned int baud;
+	u32 usartdiv, mantissa, fraction, oversampling;
+	tcflag_t cflag = termios->c_cflag;
+	u32 cr1, cr2, cr3;
+	unsigned long flags;
+
+	if (!stm32_port->hw_flow_control)
+		cflag &= ~CRTSCTS;
+
+	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 8);
+
+	spin_lock_irqsave(&port->lock, flags);
+
+	/* Stop serial port and reset value */
+	writel_relaxed(0, port->membase + USART_CR1);
+
+	cr1 = USART_CR1_TE | USART_CR1_RE | USART_CR1_UE | USART_CR1_RXNEIE;
+	cr2 = 0;
+	cr3 = 0;
+
+	if (cflag & CSTOPB)
+		cr2 |= USART_CR2_STOP_2B;
+
+	if (cflag & PARENB) {
+		cr1 |= USART_CR1_PCE;
+		if ((cflag & CSIZE) == CS8)
+			cr1 |= USART_CR1_M;
+	}
+
+	if (cflag & PARODD)
+		cr1 |= USART_CR1_PS;
+
+	port->status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS);
+	if (cflag & CRTSCTS) {
+		port->status |= UPSTAT_AUTOCTS | UPSTAT_AUTORTS;
+		cr3 |= USART_CR3_CTSE;
+	}
+
+	usartdiv = DIV_ROUND_CLOSEST(port->uartclk, baud);
+
+	/*
+	 * The USART supports 16 or 8 times oversampling.
+	 * By default we prefer 16 times oversampling, so that the receiver
+	 * has a better tolerance to clock deviations.
+	 * 8 times oversampling is only used to achieve higher speeds.
+	 */
+	if (usartdiv < 16) {
+		oversampling = 8;
+		stm32_set_bits(port, USART_CR1, USART_CR1_OVER8);
+	} else {
+		oversampling = 16;
+		stm32_clr_bits(port, USART_CR1, USART_CR1_OVER8);
+	}
+
+	mantissa = (usartdiv / oversampling) << USART_BRR_DIV_M_SHIFT;
+	fraction = usartdiv % oversampling;
+	writel_relaxed(mantissa | fraction, port->membase + USART_BRR);
+
+	uart_update_timeout(port, cflag, baud);
+
+	port->read_status_mask = USART_SR_ORE;
+	if (termios->c_iflag & INPCK)
+		port->read_status_mask |= USART_SR_PE | USART_SR_FE;
+	if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
+		port->read_status_mask |= USART_SR_LBD;
+
+	/* Characters to ignore */
+	port->ignore_status_mask = 0;
+	if (termios->c_iflag & IGNPAR)
+		port->ignore_status_mask = USART_SR_PE | USART_SR_FE;
+	if (termios->c_iflag & IGNBRK) {
+		port->ignore_status_mask |= USART_SR_LBD;
+		/*
+		 * If we're ignoring parity and break indicators,
+		 * ignore overruns too (for real raw support).
+		 */
+		if (termios->c_iflag & IGNPAR)
+			port->ignore_status_mask |= USART_SR_ORE;
+	}
+
+	/* Ignore all characters if CREAD is not set */
+	if ((termios->c_cflag & CREAD) == 0)
+		port->ignore_status_mask |= USART_SR_DUMMY_RX;
+
+	writel_relaxed(cr3, port->membase + USART_CR3);
+	writel_relaxed(cr2, port->membase + USART_CR2);
+	writel_relaxed(cr1, port->membase + USART_CR1);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *stm32_type(struct uart_port *port)
+{
+	return (port->type == PORT_STM32) ? DRIVER_NAME : NULL;
+}
+
+static void stm32_release_port(struct uart_port *port)
+{
+}
+
+static int stm32_request_port(struct uart_port *port)
+{
+	return 0;
+}
+
+static void stm32_config_port(struct uart_port *port, int flags)
+{
+	if (flags & UART_CONFIG_TYPE)
+		port->type = PORT_STM32;
+}
+
+static int
+stm32_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+	/* No user changeable parameters */
+	return -EINVAL;
+}
+
+static void stm32_pm(struct uart_port *port, unsigned int state,
+		unsigned int oldstate)
+{
+	struct stm32_port *stm32port = container_of(port,
+			struct stm32_port, port);
+	unsigned long flags = 0;
+
+	switch (state) {
+	case UART_PM_STATE_ON:
+		clk_prepare_enable(stm32port->clk);
+		break;
+	case UART_PM_STATE_OFF:
+		spin_lock_irqsave(&port->lock, flags);
+		stm32_clr_bits(port, USART_CR1, USART_CR1_UE);
+		spin_unlock_irqrestore(&port->lock, flags);
+		clk_disable_unprepare(stm32port->clk);
+		break;
+	}
+}
+
+static const struct uart_ops stm32_uart_ops = {
+	.tx_empty	= stm32_tx_empty,
+	.set_mctrl	= stm32_set_mctrl,
+	.get_mctrl	= stm32_get_mctrl,
+	.stop_tx	= stm32_stop_tx,
+	.start_tx	= stm32_start_tx,
+	.throttle	= stm32_throttle,
+	.unthrottle	= stm32_unthrottle,
+	.stop_rx	= stm32_stop_rx,
+	.break_ctl	= stm32_break_ctl,
+	.startup	= stm32_startup,
+	.shutdown	= stm32_shutdown,
+	.set_termios	= stm32_set_termios,
+	.pm		= stm32_pm,
+	.type		= stm32_type,
+	.release_port	= stm32_release_port,
+	.request_port	= stm32_request_port,
+	.config_port	= stm32_config_port,
+	.verify_port	= stm32_verify_port,
+};
+
+static int stm32_init_port(struct stm32_port *stm32port,
+			  struct platform_device *pdev)
+{
+	struct uart_port *port = &stm32port->port;
+	struct resource *res;
+	int ret;
+
+	port->iotype	= UPIO_MEM;
+	port->flags	= UPF_BOOT_AUTOCONF;
+	port->ops	= &stm32_uart_ops;
+	port->dev	= &pdev->dev;
+	port->irq	= platform_get_irq(pdev, 0);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	port->membase = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(port->membase))
+		return PTR_ERR(port->membase);
+	port->mapbase = res->start;
+
+	spin_lock_init(&port->lock);
+
+	stm32port->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(stm32port->clk))
+		return PTR_ERR(stm32port->clk);
+
+	/* Ensure that clk rate is correct by enabling the clk */
+	ret = clk_prepare_enable(stm32port->clk);
+	if (ret)
+		return ret;
+
+	stm32port->port.uartclk = clk_get_rate(stm32port->clk);
+	if (!stm32port->port.uartclk)
+		ret = -EINVAL;
+
+	clk_disable_unprepare(stm32port->clk);
+
+	return ret;
+}
+
+static struct stm32_port *stm32_of_get_stm32_port(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	int id;
+
+	if (!np)
+		return NULL;
+
+	id = of_alias_get_id(np, "serial");
+	if (id < 0)
+		id = 0;
+
+	if (WARN_ON(id >= STM32_MAX_PORTS))
+		return NULL;
+
+	stm32_ports[id].hw_flow_control = of_property_read_bool(np,
+							"auto-flow-control");
+	stm32_ports[id].port.line = id;
+	return &stm32_ports[id];
+}
+
+#ifdef CONFIG_OF
+static const struct of_device_id stm32_match[] = {
+	{ .compatible = "st,stm32-usart", },
+	{ .compatible = "st,stm32-uart", },
+	{},
+};
+
+MODULE_DEVICE_TABLE(of, stm32_match);
+#endif
+
+static int stm32_serial_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct stm32_port *stm32port;
+
+	stm32port = stm32_of_get_stm32_port(pdev);
+	if (!stm32port)
+		return -ENODEV;
+
+	ret = stm32_init_port(stm32port, pdev);
+	if (ret)
+		return ret;
+
+	ret = uart_add_one_port(&stm32_usart_driver, &stm32port->port);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, &stm32port->port);
+
+	return 0;
+}
+
+static int stm32_serial_remove(struct platform_device *pdev)
+{
+	struct uart_port *port = platform_get_drvdata(pdev);
+
+	return uart_remove_one_port(&stm32_usart_driver, port);
+}
+
+
+#ifdef CONFIG_SERIAL_STM32_CONSOLE
+static void stm32_console_putchar(struct uart_port *port, int ch)
+{
+	while (!(readl_relaxed(port->membase + USART_SR) & USART_SR_TXE))
+		cpu_relax();
+
+	writel_relaxed(ch, port->membase + USART_DR);
+}
+
+static void stm32_console_write(struct console *co, const char *s, unsigned cnt)
+{
+	struct uart_port *port = &stm32_ports[co->index].port;
+	unsigned long flags;
+	u32 old_cr1, new_cr1;
+	int locked = 1;
+
+	local_irq_save(flags);
+	if (port->sysrq)
+		locked = 0;
+	else if (oops_in_progress)
+		locked = spin_trylock(&port->lock);
+	else
+		spin_lock(&port->lock);
+
+	/* Save and disable interrupts */
+	old_cr1 = readl_relaxed(port->membase + USART_CR1);
+	new_cr1 = old_cr1 & ~USART_CR1_IE_MASK;
+	writel_relaxed(new_cr1, port->membase + USART_CR1);
+
+	uart_console_write(port, s, cnt, stm32_console_putchar);
+
+	/* Restore interrupt state */
+	writel_relaxed(old_cr1, port->membase + USART_CR1);
+
+	if (locked)
+		spin_unlock(&port->lock);
+	local_irq_restore(flags);
+}
+
+static int stm32_console_setup(struct console *co, char *options)
+{
+	struct stm32_port *stm32port;
+	int baud = 9600;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	if (co->index >= STM32_MAX_PORTS)
+		return -ENODEV;
+
+	stm32port = &stm32_ports[co->index];
+
+	/*
+	 * This driver does not support early console initialization
+	 * (use ARM early printk support instead), so we only expect
+	 * this to be called during the uart port registration when the
+	 * driver gets probed and the port should be mapped at that point.
+	 */
+	if (stm32port->port.mapbase == 0 || stm32port->port.membase == NULL)
+		return -ENXIO;
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+	return uart_set_options(&stm32port->port, co, baud, parity, bits, flow);
+}
+
+static struct console stm32_console = {
+	.name		= STM32_SERIAL_NAME,
+	.device		= uart_console_device,
+	.write		= stm32_console_write,
+	.setup		= stm32_console_setup,
+	.flags		= CON_PRINTBUFFER,
+	.index		= -1,
+	.data		= &stm32_usart_driver,
+};
+
+#define STM32_SERIAL_CONSOLE (&stm32_console)
+
+#else
+#define STM32_SERIAL_CONSOLE NULL
+#endif /* CONFIG_SERIAL_STM32_CONSOLE */
+
+static struct uart_driver stm32_usart_driver = {
+	.driver_name	= DRIVER_NAME,
+	.dev_name	= STM32_SERIAL_NAME,
+	.major		= 0,
+	.minor		= 0,
+	.nr		= STM32_MAX_PORTS,
+	.cons		= STM32_SERIAL_CONSOLE,
+};
+
+static struct platform_driver stm32_serial_driver = {
+	.probe		= stm32_serial_probe,
+	.remove		= stm32_serial_remove,
+	.driver	= {
+		.name	= DRIVER_NAME,
+		.of_match_table = of_match_ptr(stm32_match),
+	},
+};
+
+static int __init usart_init(void)
+{
+	static char banner[] __initdata = "STM32 USART driver initialized";
+	int ret;
+
+	pr_info("%s\n", banner);
+
+	ret = uart_register_driver(&stm32_usart_driver);
+	if (ret)
+		return ret;
+
+	ret = platform_driver_register(&stm32_serial_driver);
+	if (ret)
+		uart_unregister_driver(&stm32_usart_driver);
+
+	return ret;
+}
+
+static void __exit usart_exit(void)
+{
+	platform_driver_unregister(&stm32_serial_driver);
+	uart_unregister_driver(&stm32_usart_driver);
+}
+
+module_init(usart_init);
+module_exit(usart_exit);
+
+MODULE_ALIAS("platform:" DRIVER_NAME);
+MODULE_DESCRIPTION("STMicroelectronics STM32 serial port driver");
+MODULE_LICENSE("GPL v2");

include/uapi/linux/serial_core.h

@@ -258,4 +258,7 @@
 /* Cris v10 / v32 SoC */
 #define PORT_CRIS	112
 
+/* STM32 USART */
+#define PORT_STM32	113
+
 #endif /* _UAPILINUX_SERIAL_CORE_H */