|
|
@@ -1,163 +0,0 @@
|
|
|
-* Samsung S5M8767 Voltage and Current Regulator
|
|
|
-
|
|
|
-The Samsung S5M8767 is a multi-function device which includes voltage and
|
|
|
-current regulators, rtc, charger controller and other sub-blocks. It is
|
|
|
-interfaced to the host controller using a i2c interface. Each sub-block is
|
|
|
-addressed by the host system using different i2c slave address. This document
|
|
|
-describes the bindings for 'pmic' sub-block of s5m8767.
|
|
|
-
|
|
|
-Required properties:
|
|
|
-- compatible: Should be "samsung,s5m8767-pmic".
|
|
|
-- reg: Specifies the i2c slave address of the pmic block. It should be 0x66.
|
|
|
-
|
|
|
-- s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
|
|
|
- units for buck2 when changing voltage using gpio dvs. Refer to [1] below
|
|
|
- for additional information.
|
|
|
-
|
|
|
-- s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
|
|
|
- units for buck3 when changing voltage using gpio dvs. Refer to [1] below
|
|
|
- for additional information.
|
|
|
-
|
|
|
-- s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
|
|
|
- units for buck4 when changing voltage using gpio dvs. Refer to [1] below
|
|
|
- for additional information.
|
|
|
-
|
|
|
-- s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used
|
|
|
- for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines.
|
|
|
-
|
|
|
-[1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
|
|
|
- property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage'
|
|
|
- property should specify atleast one voltage level (which would be a
|
|
|
- safe operating voltage).
|
|
|
-
|
|
|
- If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
|
|
|
- property is specified, then all the eight voltage values for the
|
|
|
- 's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified.
|
|
|
-
|
|
|
-Optional properties:
|
|
|
-- interrupt-parent: Specifies the phandle of the interrupt controller to which
|
|
|
- the interrupts from s5m8767 are delivered to.
|
|
|
-- interrupts: Interrupt specifiers for two interrupt sources.
|
|
|
- - First interrupt specifier is for 'irq1' interrupt.
|
|
|
- - Second interrupt specifier is for 'alert' interrupt.
|
|
|
-- s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
|
|
|
-- s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs.
|
|
|
-- s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs.
|
|
|
-
|
|
|
-Additional properties required if either of the optional properties are used:
|
|
|
-
|
|
|
-- s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from
|
|
|
- the possible 8 options selectable by the dvs gpios. The value of this
|
|
|
- property should be between 0 and 7. If not specified or if out of range, the
|
|
|
- default value of this property is set to 0.
|
|
|
-
|
|
|
-- s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used
|
|
|
- for dvs. The format of the gpio specifier depends in the gpio controller.
|
|
|
-
|
|
|
-Regulators: The regulators of s5m8767 that have to be instantiated should be
|
|
|
-included in a sub-node named 'regulators'. Regulator nodes included in this
|
|
|
-sub-node should be of the format as listed below.
|
|
|
-
|
|
|
- regulator_name {
|
|
|
- ldo1_reg: LDO1 {
|
|
|
- regulator-name = "VDD_ALIVE_1.0V";
|
|
|
- regulator-min-microvolt = <1100000>;
|
|
|
- regulator-max-microvolt = <1100000>;
|
|
|
- regulator-always-on;
|
|
|
- regulator-boot-on;
|
|
|
- op_mode = <1>; /* Normal Mode */
|
|
|
- };
|
|
|
- };
|
|
|
-The above regulator entries are defined in regulator bindings documentation
|
|
|
-except these properties:
|
|
|
- - op_mode: describes the different operating modes of the LDO's with
|
|
|
- power mode change in SOC. The different possible values are,
|
|
|
- 0 - always off mode
|
|
|
- 1 - on in normal mode
|
|
|
- 2 - low power mode
|
|
|
- 3 - suspend mode
|
|
|
- - s5m8767,pmic-ext-control-gpios: (optional) GPIO specifier for one
|
|
|
- GPIO controlling this regulator (enable/disable); This is
|
|
|
- valid only for buck9.
|
|
|
-
|
|
|
-The following are the names of the regulators that the s5m8767 pmic block
|
|
|
-supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
|
|
|
-as per the datasheet of s5m8767.
|
|
|
-
|
|
|
- - LDOn
|
|
|
- - valid values for n are 1 to 28
|
|
|
- - Example: LDO1, LDO2, LDO28
|
|
|
- - BUCKn
|
|
|
- - valid values for n are 1 to 9.
|
|
|
- - Example: BUCK1, BUCK2, BUCK9
|
|
|
-
|
|
|
-The bindings inside the regulator nodes use the standard regulator bindings
|
|
|
-which are documented elsewhere.
|
|
|
-
|
|
|
-Example:
|
|
|
-
|
|
|
- s5m8767_pmic@66 {
|
|
|
- compatible = "samsung,s5m8767-pmic";
|
|
|
- reg = <0x66>;
|
|
|
-
|
|
|
- s5m8767,pmic-buck2-uses-gpio-dvs;
|
|
|
- s5m8767,pmic-buck3-uses-gpio-dvs;
|
|
|
- s5m8767,pmic-buck4-uses-gpio-dvs;
|
|
|
-
|
|
|
- s5m8767,pmic-buck-default-dvs-idx = <0>;
|
|
|
-
|
|
|
- s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */
|
|
|
- <&gpx0 1 0>, /* DVS2 */
|
|
|
- <&gpx0 2 0>; /* DVS3 */
|
|
|
-
|
|
|
- s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */
|
|
|
- <&gpx2 4 0>, /* SET2 */
|
|
|
- <&gpx2 5 0>; /* SET3 */
|
|
|
-
|
|
|
- s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
|
|
|
- <1250000>, <1200000>,
|
|
|
- <1150000>, <1100000>,
|
|
|
- <1000000>, <950000>;
|
|
|
-
|
|
|
- s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
|
|
|
- <1100000>, <1100000>,
|
|
|
- <1000000>, <1000000>,
|
|
|
- <1000000>, <1000000>;
|
|
|
-
|
|
|
- s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
|
|
|
- <1200000>, <1200000>,
|
|
|
- <1200000>, <1200000>,
|
|
|
- <1200000>, <1200000>;
|
|
|
-
|
|
|
- regulators {
|
|
|
- ldo1_reg: LDO1 {
|
|
|
- regulator-name = "VDD_ABB_3.3V";
|
|
|
- regulator-min-microvolt = <3300000>;
|
|
|
- regulator-max-microvolt = <3300000>;
|
|
|
- op_mode = <1>; /* Normal Mode */
|
|
|
- };
|
|
|
-
|
|
|
- ldo2_reg: LDO2 {
|
|
|
- regulator-name = "VDD_ALIVE_1.1V";
|
|
|
- regulator-min-microvolt = <1100000>;
|
|
|
- regulator-max-microvolt = <1100000>;
|
|
|
- regulator-always-on;
|
|
|
- };
|
|
|
-
|
|
|
- buck1_reg: BUCK1 {
|
|
|
- regulator-name = "VDD_MIF_1.2V";
|
|
|
- regulator-min-microvolt = <950000>;
|
|
|
- regulator-max-microvolt = <1350000>;
|
|
|
- regulator-always-on;
|
|
|
- regulator-boot-on;
|
|
|
- };
|
|
|
-
|
|
|
- vemmc_reg: BUCK9 {
|
|
|
- regulator-name = "VMEM_VDD_2.8V";
|
|
|
- regulator-min-microvolt = <2800000>;
|
|
|
- regulator-max-microvolt = <2800000>;
|
|
|
- op_mode = <3>; /* Standby Mode */
|
|
|
- s5m8767,pmic-ext-control-gpios = <&gpk0 2 0>;
|
|
|
- };
|
|
|
- };
|
|
|
- };
|
Krzysztof Kozlowski