ARM: GIC: Make MULTI_IRQ_HANDLER mandatory

Now that MULTI_IRQ_HANDLER is selected by all the in-tree
GIC users, make it mandatory and remove the unused macros.

Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

arch/arm/Kconfig

@@ -278,7 +278,6 @@ config ARCH_REALVIEW
 	select ARM_TIMER_SP804
 	select GPIO_PL061 if GPIOLIB
 	select NEED_MACH_MEMORY_H
-	select MULTI_IRQ_HANDLER
 	help
 	  This enables support for ARM Ltd RealView boards.
 
@@ -311,7 +310,6 @@ config ARCH_VEXPRESS
 	select ICST
 	select PLAT_VERSATILE
 	select PLAT_VERSATILE_CLCD
-	select MULTI_IRQ_HANDLER
 	help
 	  This enables support for the ARM Ltd Versatile Express boards.
 
@@ -347,7 +345,6 @@ config ARCH_HIGHBANK
 	select GENERIC_CLOCKEVENTS
 	select HAVE_ARM_SCU
 	select USE_OF
-	select MULTI_IRQ_HANDLER
 	help
 	  Support for the Calxeda Highbank SoC based boards.
 
@@ -366,7 +363,6 @@ config ARCH_CNS3XXX
 	select ARM_GIC
 	select MIGHT_HAVE_PCI
 	select PCI_DOMAINS if PCI
-	select MULTI_IRQ_HANDLER
 	help
 	  Support for Cavium Networks CNS3XXX platform.
 
@@ -855,7 +851,6 @@ config ARCH_EXYNOS
 	select HAVE_S3C2410_I2C if I2C
 	select HAVE_S3C2410_WATCHDOG if WATCHDOG
 	select NEED_MACH_MEMORY_H
-	select MULTI_IRQ_HANDLER
 	help
 	  Support for SAMSUNG's EXYNOS SoCs (EXYNOS4/5)
 
@@ -979,7 +974,6 @@ config ARCH_ZYNQ
 	select ARM_AMBA
 	select ICST
 	select USE_OF
-	select MULTI_IRQ_HANDLER
 	help
 	  Support for Xilinx Zynq ARM Cortex A9 Platform
 endchoice

arch/arm/common/Kconfig

@@ -1,5 +1,6 @@
 config ARM_GIC
 	select IRQ_DOMAIN
+	select MULTI_IRQ_HANDLER
 	bool
 
 config GIC_NON_BANKED

arch/arm/common/gic.c

@@ -71,9 +71,6 @@ struct gic_chip_data {
 
 static DEFINE_RAW_SPINLOCK(irq_controller_lock);
 
-/* Address of GIC 0 CPU interface */
-void __iomem *gic_cpu_base_addr __read_mostly;
-
 /*
  * Supported arch specific GIC irq extension.
  * Default make them NULL.
@@ -700,7 +697,6 @@ void __init gic_init_bases(unsigned int gic_nr, int irq_start,
 	 * For secondary GICs, skip over PPIs, too.
 	 */
 	if (gic_nr == 0) {
-		gic_cpu_base_addr = cpu_base;
 		domain->hwirq_base = 16;
 		if (irq_start > 0)
 			irq_start = (irq_start & ~31) + 16;

arch/arm/include/asm/hardware/entry-macro-gic.S

@@ -1,60 +0,0 @@
-/*
- * arch/arm/include/asm/hardware/entry-macro-gic.S
- *
- * Low-level IRQ helper macros for GIC
- *
- * This file is licensed under  the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <asm/hardware/gic.h>
-
-#ifndef HAVE_GET_IRQNR_PREAMBLE
-	.macro	get_irqnr_preamble, base, tmp
-	ldr	\base, =gic_cpu_base_addr
-	ldr	\base, [\base]
-	.endm
-#endif
-
-/*
- * The interrupt numbering scheme is defined in the
- * interrupt controller spec.  To wit:
- *
- * Interrupts 0-15 are IPI
- * 16-31 are local.  We allow 30 to be used for the watchdog.
- * 32-1020 are global
- * 1021-1022 are reserved
- * 1023 is "spurious" (no interrupt)
- *
- * A simple read from the controller will tell us the number of the highest
- * priority enabled interrupt.  We then just need to check whether it is in the
- * valid range for an IRQ (30-1020 inclusive).
- */
-
-	.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-
-	ldr     \irqstat, [\base, #GIC_CPU_INTACK]
-	/* bits 12-10 = src CPU, 9-0 = int # */
-
-	ldr	\tmp, =1021
-	bic     \irqnr, \irqstat, #0x1c00
-	cmp     \irqnr, #15
-	cmpcc	\irqnr, \irqnr
-	cmpne	\irqnr, \tmp
-	cmpcs	\irqnr, \irqnr
-	.endm
-
-/* We assume that irqstat (the raw value of the IRQ acknowledge
- * register) is preserved from the macro above.
- * If there is an IPI, we immediately signal end of interrupt on the
- * controller, since this requires the original irqstat value which
- * we won't easily be able to recreate later.
- */
-
-	.macro test_for_ipi, irqnr, irqstat, base, tmp
-	bic	\irqnr, \irqstat, #0x1c00
-	cmp	\irqnr, #16
-	strcc	\irqstat, [\base, #GIC_CPU_EOI]
-	cmpcs	\irqnr, \irqnr
-	.endm

arch/arm/include/asm/hardware/gic.h

@@ -36,7 +36,6 @@
 #include <linux/irqdomain.h>
 struct device_node;
 
-extern void __iomem *gic_cpu_base_addr;
 extern struct irq_chip gic_arch_extn;
 
 void gic_init_bases(unsigned int, int, void __iomem *, void __iomem *,

arch/arm/mach-msm/Kconfig

@@ -50,7 +50,6 @@ config ARCH_MSM8X60
 	select GPIO_MSM_V2
 	select MSM_GPIOMUX
 	select MSM_SCM if SMP
-	select MULTI_IRQ_HANDLER
 
 config ARCH_MSM8960
 	bool "MSM8960"
@@ -61,7 +60,6 @@ config ARCH_MSM8960
 	select MSM_V2_TLMM
 	select MSM_GPIOMUX
 	select MSM_SCM if SMP
-	select MULTI_IRQ_HANDLER
 
 endchoice
 

arch/arm/mach-omap2/Kconfig

@@ -37,6 +37,7 @@ config ARCH_OMAP3
 	select ARCH_HAS_OPP
 	select PM_OPP if PM
 	select ARM_CPU_SUSPEND if PM
+	select MULTI_IRQ_HANDLER
 
 config ARCH_OMAP4
 	bool "TI OMAP4"

arch/arm/mach-tegra/Kconfig

@@ -13,7 +13,6 @@ config ARCH_TEGRA_2x_SOC
 	select USB_ARCH_HAS_EHCI if USB_SUPPORT
 	select USB_ULPI if USB_SUPPORT
 	select USB_ULPI_VIEWPORT if USB_SUPPORT
-	select MULTI_IRQ_HANDLER
 	help
 	  Support for NVIDIA Tegra AP20 and T20 processors, based on the
 	  ARM CortexA9MP CPU and the ARM PL310 L2 cache controller

arch/arm/mach-ux500/Kconfig

@@ -7,7 +7,6 @@ config UX500_SOC_COMMON
 	select HAS_MTU
 	select ARM_ERRATA_753970
 	select ARM_ERRATA_754322
-	select MULTI_IRQ_HANDLER
 
 menu "Ux500 SoC"
 

arch/arm/plat-omap/Kconfig

@@ -24,7 +24,6 @@ config ARCH_OMAP2PLUS
 	select CLKDEV_LOOKUP
 	select GENERIC_IRQ_CHIP
 	select OMAP_DM_TIMER
-	select MULTI_IRQ_HANDLER
 	help
 	  "Systems based on OMAP2, OMAP3 or OMAP4"