linux_kernel/drivers/net/ethernet/stmicro/stmmac/dwmac4_dma.c

/*
 * This is the driver for the GMAC on-chip Ethernet controller for ST SoCs.
 * DWC Ether MAC version 4.xx  has been used for  developing this code.
 *
 * This contains the functions to handle the dma.
 *
 * Copyright (C) 2015  STMicroelectronics Ltd
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms and conditions of the GNU General Public License,
 * version 2, as published by the Free Software Foundation.
 *
 * Author: Alexandre Torgue <alexandre.torgue@st.com>
 */

#include <linux/io.h>
#include "dwmac4.h"
#include "dwmac4_dma.h"

static void dwmac4_dma_axi(void __iomem *ioaddr, struct stmmac_axi *axi)
{
	u32 value = readl(ioaddr + DMA_SYS_BUS_MODE);
	int i;

	pr_info("dwmac4: Master AXI performs %s burst length\n",
		(value & DMA_SYS_BUS_FB) ? "fixed" : "any");

	if (axi->axi_lpi_en)
		value |= DMA_AXI_EN_LPI;
	if (axi->axi_xit_frm)
		value |= DMA_AXI_LPI_XIT_FRM;

	value |= (axi->axi_wr_osr_lmt & DMA_AXI_OSR_MAX) <<
		 DMA_AXI_WR_OSR_LMT_SHIFT;

	value |= (axi->axi_rd_osr_lmt & DMA_AXI_OSR_MAX) <<
		 DMA_AXI_RD_OSR_LMT_SHIFT;

	/* Depending on the UNDEF bit the Master AXI will perform any burst
	 * length according to the BLEN programmed (by default all BLEN are
	 * set).
	 */
	for (i = 0; i < AXI_BLEN; i++) {
		switch (axi->axi_blen[i]) {
		case 256:
			value |= DMA_AXI_BLEN256;
			break;
		case 128:
			value |= DMA_AXI_BLEN128;
			break;
		case 64:
			value |= DMA_AXI_BLEN64;
			break;
		case 32:
			value |= DMA_AXI_BLEN32;
			break;
		case 16:
			value |= DMA_AXI_BLEN16;
			break;
		case 8:
			value |= DMA_AXI_BLEN8;
			break;
		case 4:
			value |= DMA_AXI_BLEN4;
			break;
		}
	}

	writel(value, ioaddr + DMA_SYS_BUS_MODE);
}

static void dwmac4_dma_init_channel(void __iomem *ioaddr, int pbl,
				    u32 dma_tx_phy, u32 dma_rx_phy,
				    u32 channel)
{
	u32 value;

	/* set PBL for each channels. Currently we affect same configuration
	 * on each channel
	 */
	value = readl(ioaddr + DMA_CHAN_CONTROL(channel));
	value = value | DMA_BUS_MODE_PBL;
	writel(value, ioaddr + DMA_CHAN_CONTROL(channel));

	value = readl(ioaddr + DMA_CHAN_TX_CONTROL(channel));
	value = value | (pbl << DMA_BUS_MODE_PBL_SHIFT);
	writel(value, ioaddr + DMA_CHAN_TX_CONTROL(channel));

	value = readl(ioaddr + DMA_CHAN_RX_CONTROL(channel));
	value = value | (pbl << DMA_BUS_MODE_RPBL_SHIFT);
	writel(value, ioaddr + DMA_CHAN_RX_CONTROL(channel));

	/* Mask interrupts by writing to CSR7 */
	writel(DMA_CHAN_INTR_DEFAULT_MASK, ioaddr + DMA_CHAN_INTR_ENA(channel));

	writel(dma_tx_phy, ioaddr + DMA_CHAN_TX_BASE_ADDR(channel));
	writel(dma_rx_phy, ioaddr + DMA_CHAN_RX_BASE_ADDR(channel));
}

static void dwmac4_dma_init(void __iomem *ioaddr, int pbl, int fb, int mb,
			    int aal, u32 dma_tx, u32 dma_rx, int atds)
{
	u32 value = readl(ioaddr + DMA_SYS_BUS_MODE);
	int i;

	/* Set the Fixed burst mode */
	if (fb)
		value |= DMA_SYS_BUS_FB;

	/* Mixed Burst has no effect when fb is set */
	if (mb)
		value |= DMA_SYS_BUS_MB;

	if (aal)
		value |= DMA_SYS_BUS_AAL;

	writel(value, ioaddr + DMA_SYS_BUS_MODE);

	for (i = 0; i < DMA_CHANNEL_NB_MAX; i++)
		dwmac4_dma_init_channel(ioaddr, pbl, dma_tx, dma_rx, i);
}

static void _dwmac4_dump_dma_regs(void __iomem *ioaddr, u32 channel)
{
	pr_debug(" Channel %d\n", channel);
	pr_debug("\tDMA_CHAN_CONTROL, offset: 0x%x, val: 0x%x\n", 0,
		 readl(ioaddr + DMA_CHAN_CONTROL(channel)));
	pr_debug("\tDMA_CHAN_TX_CONTROL, offset: 0x%x, val: 0x%x\n", 0x4,
		 readl(ioaddr + DMA_CHAN_TX_CONTROL(channel)));
	pr_debug("\tDMA_CHAN_RX_CONTROL, offset: 0x%x, val: 0x%x\n", 0x8,
		 readl(ioaddr + DMA_CHAN_RX_CONTROL(channel)));
	pr_debug("\tDMA_CHAN_TX_BASE_ADDR, offset: 0x%x, val: 0x%x\n", 0x14,
		 readl(ioaddr + DMA_CHAN_TX_BASE_ADDR(channel)));
	pr_debug("\tDMA_CHAN_RX_BASE_ADDR, offset: 0x%x, val: 0x%x\n", 0x1c,
		 readl(ioaddr + DMA_CHAN_RX_BASE_ADDR(channel)));
	pr_debug("\tDMA_CHAN_TX_END_ADDR, offset: 0x%x, val: 0x%x\n", 0x20,
		 readl(ioaddr + DMA_CHAN_TX_END_ADDR(channel)));
	pr_debug("\tDMA_CHAN_RX_END_ADDR, offset: 0x%x, val: 0x%x\n", 0x28,
		 readl(ioaddr + DMA_CHAN_RX_END_ADDR(channel)));
	pr_debug("\tDMA_CHAN_TX_RING_LEN, offset: 0x%x, val: 0x%x\n", 0x2c,
		 readl(ioaddr + DMA_CHAN_TX_RING_LEN(channel)));
	pr_debug("\tDMA_CHAN_RX_RING_LEN, offset: 0x%x, val: 0x%x\n", 0x30,
		 readl(ioaddr + DMA_CHAN_RX_RING_LEN(channel)));
	pr_debug("\tDMA_CHAN_INTR_ENA, offset: 0x%x, val: 0x%x\n", 0x34,
		 readl(ioaddr + DMA_CHAN_INTR_ENA(channel)));
	pr_debug("\tDMA_CHAN_RX_WATCHDOG, offset: 0x%x, val: 0x%x\n", 0x38,
		 readl(ioaddr + DMA_CHAN_RX_WATCHDOG(channel)));
	pr_debug("\tDMA_CHAN_SLOT_CTRL_STATUS, offset: 0x%x, val: 0x%x\n", 0x3c,
		 readl(ioaddr + DMA_CHAN_SLOT_CTRL_STATUS(channel)));
	pr_debug("\tDMA_CHAN_CUR_TX_DESC, offset: 0x%x, val: 0x%x\n", 0x44,
		 readl(ioaddr + DMA_CHAN_CUR_TX_DESC(channel)));
	pr_debug("\tDMA_CHAN_CUR_RX_DESC, offset: 0x%x, val: 0x%x\n", 0x4c,
		 readl(ioaddr + DMA_CHAN_CUR_RX_DESC(channel)));
	pr_debug("\tDMA_CHAN_CUR_TX_BUF_ADDR, offset: 0x%x, val: 0x%x\n", 0x54,
		 readl(ioaddr + DMA_CHAN_CUR_TX_BUF_ADDR(channel)));
	pr_debug("\tDMA_CHAN_CUR_RX_BUF_ADDR, offset: 0x%x, val: 0x%x\n", 0x5c,
		 readl(ioaddr + DMA_CHAN_CUR_RX_BUF_ADDR(channel)));
	pr_debug("\tDMA_CHAN_STATUS, offset: 0x%x, val: 0x%x\n", 0x60,
		 readl(ioaddr + DMA_CHAN_STATUS(channel)));
}

static void dwmac4_dump_dma_regs(void __iomem *ioaddr)
{
	int i;

	pr_debug(" GMAC4 DMA registers\n");

	for (i = 0; i < DMA_CHANNEL_NB_MAX; i++)
		_dwmac4_dump_dma_regs(ioaddr, i);
}

static void dwmac4_rx_watchdog(void __iomem *ioaddr, u32 riwt)
{
	int i;

	for (i = 0; i < DMA_CHANNEL_NB_MAX; i++)
		writel(riwt, ioaddr + DMA_CHAN_RX_WATCHDOG(i));
}

static void dwmac4_dma_chan_op_mode(void __iomem *ioaddr, int txmode,
				    int rxmode, u32 channel)
{
	u32 mtl_tx_op, mtl_rx_op, mtl_rx_int;

	/* Following code only done for channel 0, other channels not yet
	 * supported.
	 */
	mtl_tx_op = readl(ioaddr + MTL_CHAN_TX_OP_MODE(channel));

	if (txmode == SF_DMA_MODE) {
		pr_debug("GMAC: enable TX store and forward mode\n");
		/* Transmit COE type 2 cannot be done in cut-through mode. */
		mtl_tx_op |= MTL_OP_MODE_TSF;
	} else {
		pr_debug("GMAC: disabling TX SF (threshold %d)\n", txmode);
		mtl_tx_op &= ~MTL_OP_MODE_TSF;
		mtl_tx_op &= MTL_OP_MODE_TTC_MASK;
		/* Set the transmit threshold */
		if (txmode <= 32)
			mtl_tx_op |= MTL_OP_MODE_TTC_32;
		else if (txmode <= 64)
			mtl_tx_op |= MTL_OP_MODE_TTC_64;
		else if (txmode <= 96)
			mtl_tx_op |= MTL_OP_MODE_TTC_96;
		else if (txmode <= 128)
			mtl_tx_op |= MTL_OP_MODE_TTC_128;
		else if (txmode <= 192)
			mtl_tx_op |= MTL_OP_MODE_TTC_192;
		else if (txmode <= 256)
			mtl_tx_op |= MTL_OP_MODE_TTC_256;
		else if (txmode <= 384)
			mtl_tx_op |= MTL_OP_MODE_TTC_384;
		else
			mtl_tx_op |= MTL_OP_MODE_TTC_512;
	}

	writel(mtl_tx_op, ioaddr +  MTL_CHAN_TX_OP_MODE(channel));

	mtl_rx_op = readl(ioaddr + MTL_CHAN_RX_OP_MODE(channel));

	if (rxmode == SF_DMA_MODE) {
		pr_debug("GMAC: enable RX store and forward mode\n");
		mtl_rx_op |= MTL_OP_MODE_RSF;
	} else {
		pr_debug("GMAC: disable RX SF mode (threshold %d)\n", rxmode);
		mtl_rx_op &= ~MTL_OP_MODE_RSF;
		mtl_rx_op &= MTL_OP_MODE_RTC_MASK;
		if (rxmode <= 32)
			mtl_rx_op |= MTL_OP_MODE_RTC_32;
		else if (rxmode <= 64)
			mtl_rx_op |= MTL_OP_MODE_RTC_64;
		else if (rxmode <= 96)
			mtl_rx_op |= MTL_OP_MODE_RTC_96;
		else
			mtl_rx_op |= MTL_OP_MODE_RTC_128;
	}

	writel(mtl_rx_op, ioaddr + MTL_CHAN_RX_OP_MODE(channel));

	/* Enable MTL RX overflow */
	mtl_rx_int = readl(ioaddr + MTL_CHAN_INT_CTRL(channel));
	writel(mtl_rx_int | MTL_RX_OVERFLOW_INT_EN,
	       ioaddr + MTL_CHAN_INT_CTRL(channel));
}

static void dwmac4_dma_operation_mode(void __iomem *ioaddr, int txmode,
				      int rxmode, int rxfifosz)
{
	/* Only Channel 0 is actually configured and used */
	dwmac4_dma_chan_op_mode(ioaddr, txmode, rxmode, 0);
}

static void dwmac4_get_hw_feature(void __iomem *ioaddr,
				  struct dma_features *dma_cap)
{
	u32 hw_cap = readl(ioaddr + GMAC_HW_FEATURE0);

	/*  MAC HW feature0 */
	dma_cap->mbps_10_100 = (hw_cap & GMAC_HW_FEAT_MIISEL);
	dma_cap->mbps_1000 = (hw_cap & GMAC_HW_FEAT_GMIISEL) >> 1;
	dma_cap->half_duplex = (hw_cap & GMAC_HW_FEAT_HDSEL) >> 2;
	dma_cap->hash_filter = (hw_cap & GMAC_HW_FEAT_VLHASH) >> 4;
	dma_cap->multi_addr = (hw_cap & GMAC_HW_FEAT_ADDMAC) >> 18;
	dma_cap->pcs = (hw_cap & GMAC_HW_FEAT_PCSSEL) >> 3;
	dma_cap->sma_mdio = (hw_cap & GMAC_HW_FEAT_SMASEL) >> 5;
	dma_cap->pmt_remote_wake_up = (hw_cap & GMAC_HW_FEAT_RWKSEL) >> 6;
	dma_cap->pmt_magic_frame = (hw_cap & GMAC_HW_FEAT_MGKSEL) >> 7;
	/* MMC */
	dma_cap->rmon = (hw_cap & GMAC_HW_FEAT_MMCSEL) >> 8;
	/* IEEE 1588-2008 */
	dma_cap->atime_stamp = (hw_cap & GMAC_HW_FEAT_TSSEL) >> 12;
	/* 802.3az - Energy-Efficient Ethernet (EEE) */
	dma_cap->eee = (hw_cap & GMAC_HW_FEAT_EEESEL) >> 13;
	/* TX and RX csum */
	dma_cap->tx_coe = (hw_cap & GMAC_HW_FEAT_TXCOSEL) >> 14;
	dma_cap->rx_coe =  (hw_cap & GMAC_HW_FEAT_RXCOESEL) >> 16;

	/* MAC HW feature1 */
	hw_cap = readl(ioaddr + GMAC_HW_FEATURE1);
	dma_cap->av = (hw_cap & GMAC_HW_FEAT_AVSEL) >> 20;
	dma_cap->tsoen = (hw_cap & GMAC_HW_TSOEN) >> 18;
	/* MAC HW feature2 */
	hw_cap = readl(ioaddr + GMAC_HW_FEATURE2);
	/* TX and RX number of channels */
	dma_cap->number_rx_channel =
		((hw_cap & GMAC_HW_FEAT_RXCHCNT) >> 12) + 1;
	dma_cap->number_tx_channel =
		((hw_cap & GMAC_HW_FEAT_TXCHCNT) >> 18) + 1;

	/* IEEE 1588-2002 */
	dma_cap->time_stamp = 0;
}

/* Enable/disable TSO feature and set MSS */
static void dwmac4_enable_tso(void __iomem *ioaddr, bool en, u32 chan)
{
	u32 value;

	if (en) {
		/* enable TSO */
		value = readl(ioaddr + DMA_CHAN_TX_CONTROL(chan));
		writel(value | DMA_CONTROL_TSE,
		       ioaddr + DMA_CHAN_TX_CONTROL(chan));
	} else {
		/* enable TSO */
		value = readl(ioaddr + DMA_CHAN_TX_CONTROL(chan));
		writel(value & ~DMA_CONTROL_TSE,
		       ioaddr + DMA_CHAN_TX_CONTROL(chan));
	}
}

const struct stmmac_dma_ops dwmac4_dma_ops = {
	.reset = dwmac4_dma_reset,
	.init = dwmac4_dma_init,
	.axi = dwmac4_dma_axi,
	.dump_regs = dwmac4_dump_dma_regs,
	.dma_mode = dwmac4_dma_operation_mode,
	.enable_dma_irq = dwmac4_enable_dma_irq,
	.disable_dma_irq = dwmac4_disable_dma_irq,
	.start_tx = dwmac4_dma_start_tx,
	.stop_tx = dwmac4_dma_stop_tx,
	.start_rx = dwmac4_dma_start_rx,
	.stop_rx = dwmac4_dma_stop_rx,
	.dma_interrupt = dwmac4_dma_interrupt,
	.get_hw_feature = dwmac4_get_hw_feature,
	.rx_watchdog = dwmac4_rx_watchdog,
	.set_rx_ring_len = dwmac4_set_rx_ring_len,
	.set_tx_ring_len = dwmac4_set_tx_ring_len,
	.set_rx_tail_ptr = dwmac4_set_rx_tail_ptr,
	.set_tx_tail_ptr = dwmac4_set_tx_tail_ptr,
	.enable_tso = dwmac4_enable_tso,
};

const struct stmmac_dma_ops dwmac410_dma_ops = {
	.reset = dwmac4_dma_reset,
	.init = dwmac4_dma_init,
	.axi = dwmac4_dma_axi,
	.dump_regs = dwmac4_dump_dma_regs,
	.dma_mode = dwmac4_dma_operation_mode,
	.enable_dma_irq = dwmac410_enable_dma_irq,
	.disable_dma_irq = dwmac4_disable_dma_irq,
	.start_tx = dwmac4_dma_start_tx,
	.stop_tx = dwmac4_dma_stop_tx,
	.start_rx = dwmac4_dma_start_rx,
	.stop_rx = dwmac4_dma_stop_rx,
	.dma_interrupt = dwmac4_dma_interrupt,
	.get_hw_feature = dwmac4_get_hw_feature,
	.rx_watchdog = dwmac4_rx_watchdog,
	.set_rx_ring_len = dwmac4_set_rx_ring_len,
	.set_tx_ring_len = dwmac4_set_tx_ring_len,
	.set_rx_tail_ptr = dwmac4_set_rx_tail_ptr,
	.set_tx_tail_ptr = dwmac4_set_tx_tail_ptr,
	.enable_tso = dwmac4_enable_tso,
};