| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134 |
- config OMAP2_DSS_INIT
- bool
- config OMAP_DSS_BASE
- tristate
- menuconfig OMAP2_DSS
- tristate "OMAP2+ Display Subsystem support"
- select OMAP_DSS_BASE
- select VIDEOMODE_HELPERS
- select OMAP2_DSS_INIT
- select HDMI
- help
- OMAP2+ Display Subsystem support.
- if OMAP2_DSS
- config OMAP2_DSS_DEBUG
- bool "Debug support"
- default n
- help
- This enables printing of debug messages. Alternatively, debug messages
- can also be enabled by setting CONFIG_DYNAMIC_DEBUG and then setting
- appropriate flags in <debugfs>/dynamic_debug/control.
- config OMAP2_DSS_DEBUGFS
- bool "Debugfs filesystem support"
- depends on DEBUG_FS
- default n
- help
- This enables debugfs for OMAPDSS at <debugfs>/omapdss. This enables
- querying about clock configuration and register configuration of dss,
- dispc, dsi, hdmi and rfbi.
- config OMAP2_DSS_COLLECT_IRQ_STATS
- bool "Collect DSS IRQ statistics"
- depends on OMAP2_DSS_DEBUGFS
- default n
- help
- Collect DSS IRQ statistics, printable via debugfs.
- The statistics can be found from
- <debugfs>/omapdss/dispc_irq for DISPC interrupts, and
- <debugfs>/omapdss/dsi_irq for DSI interrupts.
- config OMAP2_DSS_DPI
- bool "DPI support"
- default y
- help
- DPI Interface. This is the Parallel Display Interface.
- config OMAP2_DSS_VENC
- bool "VENC support"
- default y
- help
- OMAP Video Encoder support for S-Video and composite TV-out.
- config OMAP2_DSS_HDMI_COMMON
- bool
- config OMAP4_DSS_HDMI
- bool "HDMI support for OMAP4"
- default y
- select OMAP2_DSS_HDMI_COMMON
- help
- HDMI support for OMAP4 based SoCs.
- config OMAP4_DSS_HDMI_CEC
- bool "Enable HDMI CEC support for OMAP4"
- depends on OMAP4_DSS_HDMI
- select CEC_CORE
- default y
- ---help---
- When selected the HDMI transmitter will support the CEC feature.
- config OMAP5_DSS_HDMI
- bool "HDMI support for OMAP5"
- default n
- select OMAP2_DSS_HDMI_COMMON
- help
- HDMI Interface for OMAP5 and similar cores. This adds the High
- Definition Multimedia Interface. See http://www.hdmi.org/ for HDMI
- specification.
- config OMAP2_DSS_SDI
- bool "SDI support"
- default n
- help
- SDI (Serial Display Interface) support.
- SDI is a high speed one-way display serial bus between the host
- processor and a display.
- config OMAP2_DSS_DSI
- bool "DSI support"
- default n
- help
- MIPI DSI (Display Serial Interface) support.
- DSI is a high speed half-duplex serial interface between the host
- processor and a peripheral, such as a display or a framebuffer chip.
- See http://www.mipi.org/ for DSI specifications.
- config OMAP2_DSS_MIN_FCK_PER_PCK
- int "Minimum FCK/PCK ratio (for scaling)"
- range 0 32
- default 0
- help
- This can be used to adjust the minimum FCK/PCK ratio.
- With this you can make sure that DISPC FCK is at least
- n x PCK. Video plane scaling requires higher FCK than
- normally.
- If this is set to 0, there's no extra constraint on the
- DISPC FCK. However, the FCK will at minimum be
- 2xPCK (if active matrix) or 3xPCK (if passive matrix).
- Max FCK is 173MHz, so this doesn't work if your PCK
- is very high.
- config OMAP2_DSS_SLEEP_AFTER_VENC_RESET
- bool "Sleep 20ms after VENC reset"
- default y
- help
- There is a 20ms sleep after VENC reset which seemed to fix the
- reset. The reason for the bug is unclear, and it's also unclear
- on what platforms this happens.
- This option enables the sleep, and is enabled by default. You can
- disable the sleep if it doesn't cause problems on your platform.
- endif
|
