Merge branch 'sched/urgent' into sched/core, to pick up fixes before applying new changes

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Documentation/Changes

@@ -43,7 +43,7 @@ o  udev                   081                     # udevd --version
 o  grub                   0.93                    # grub --version || grub-install --version
 o  mcelog                 0.6                     # mcelog --version
 o  iptables               1.4.2                   # iptables -V
-o  openssl & libcrypto    1.0.1k                  # openssl version
+o  openssl & libcrypto    1.0.0                   # openssl version
 
 
 Kernel compilation

Documentation/devicetree/bindings/arm/gic-v3.txt

@@ -57,6 +57,8 @@ used to route Message Signalled Interrupts (MSI) to the CPUs.
 These nodes must have the following properties:
 - compatible : Should at least contain  "arm,gic-v3-its".
 - msi-controller : Boolean property. Identifies the node as an MSI controller
+- #msi-cells: Must be <1>. The single msi-cell is the DeviceID of the device
+  which will generate the MSI.
 - reg: Specifies the base physical address and size of the ITS
   registers.
 
@@ -83,6 +85,7 @@ Examples:
 		gic-its@2c200000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c200000 0 0x200000>;
 		};
 	};
@@ -107,12 +110,14 @@ Examples:
 		gic-its@2c200000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c200000 0 0x200000>;
 		};
 
 		gic-its@2c400000 {
 			compatible = "arm,gic-v3-its";
 			msi-controller;
+			#msi-cells = <1>;
 			reg = <0x0 0x2c400000 0 0x200000>;
 		};
 	};

Documentation/devicetree/bindings/arm/idle-states.txt

@@ -497,7 +497,7 @@ cpus {
 	};
 
 	idle-states {
-		entry-method = "arm,psci";
+		entry-method = "psci";
 
 		CPU_RETENTION_0_0: cpu-retention-0-0 {
 			compatible = "arm,idle-state";

Documentation/devicetree/bindings/gpio/gpio.txt

@@ -16,7 +16,9 @@ properties, each containing a 'gpio-list':
 GPIO properties should be named "[<name>-]gpios", with <name> being the purpose
 of this GPIO for the device. While a non-existent <name> is considered valid
 for compatibility reasons (resolving to the "gpios" property), it is not allowed
-for new bindings.
+for new bindings. Also, GPIO properties named "[<name>-]gpio" are valid and old
+bindings use it, but are only supported for compatibility reasons and should not
+be used for newer bindings since it has been deprecated.
 
 GPIO properties can contain one or more GPIO phandles, but only in exceptional
 cases should they contain more than one. If your device uses several GPIOs with

Documentation/devicetree/bindings/iio/accel/bma180.txt

@@ -1,10 +1,11 @@
-* Bosch BMA180 triaxial acceleration sensor
+* Bosch BMA180 / BMA250 triaxial acceleration sensor
 
 http://omapworld.com/BMA180_111_1002839.pdf
+http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/bst-bma250-ds002-05.pdf
 
 Required properties:
 
-  - compatible : should be "bosch,bma180"
+  - compatible : should be "bosch,bma180" or "bosch,bma250"
   - reg : the I2C address of the sensor
 
 Optional properties:
@@ -13,6 +14,9 @@ Optional properties:
 
   - interrupts : interrupt mapping for GPIO IRQ, it should by configured with
 		flags IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING
+		For the bma250 the first interrupt listed must be the one
+		connected to the INT1 pin, the second (optional) interrupt
+		listed must be the one connected to the INT2 pin.
 
 Example:
 

Documentation/devicetree/bindings/input/cypress,cyapa.txt

@@ -25,7 +25,7 @@ Example:
 		/* Cypress Gen3 touchpad */
 		touchpad@67 {
 			compatible = "cypress,cyapa";
-			reg = <0x24>;
+			reg = <0x67>;
 			interrupt-parent = <&gpio>;
 			interrupts = <2 IRQ_TYPE_EDGE_FALLING>;	/* GPIO 2 */
 			wakeup-source;

Documentation/devicetree/bindings/interrupt-controller/qca,ath79-misc-intc.txt

@@ -4,8 +4,8 @@ The MISC interrupt controller is a secondary controller for lower priority
 interrupt.
 
 Required Properties:
-- compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-misc-intc"
-  as fallback
+- compatible: has to be "qca,<soctype>-cpu-intc", "qca,ar7100-misc-intc" or
+  "qca,<soctype>-cpu-intc", "qca,ar7240-misc-intc"
 - reg: Base address and size of the controllers memory area
 - interrupt-parent: phandle of the parent interrupt controller.
 - interrupts: Interrupt specifier for the controllers interrupt.
@@ -13,6 +13,9 @@ Required Properties:
 - #interrupt-cells : Specifies the number of cells needed to encode interrupt
 		     source, should be 1
 
+Compatible fallback depends on the SoC. Use ar7100 for ar71xx and ar913x,
+use ar7240 for all other SoCs.
+
 Please refer to interrupts.txt in this directory for details of the common
 Interrupt Controllers bindings used by client devices.
 
@@ -28,3 +31,16 @@ Example:
 		interrupt-controller;
 		#interrupt-cells = <1>;
 	};
+
+Another example:
+
+	interrupt-controller@18060010 {
+		compatible = "qca,ar9331-misc-intc", qca,ar7240-misc-intc";
+		reg = <0x18060010 0x4>;
+
+		interrupt-parent = <&cpuintc>;
+		interrupts = <6>;
+
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};

Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt

@@ -7,7 +7,8 @@ OHCI and EHCI controllers.
 
 Required properties:
 - compatible: "renesas,pci-r8a7790" for the R8A7790 SoC;
-	      "renesas,pci-r8a7791" for the R8A7791 SoC.
+	      "renesas,pci-r8a7791" for the R8A7791 SoC;
+	      "renesas,pci-r8a7794" for the R8A7794 SoC.
 - reg:	A list of physical regions to access the device: the first is
 	the operational registers for the OHCI/EHCI controllers and the
 	second is for the bridge configuration and control registers.

Documentation/devicetree/bindings/regulator/pbias-regulator.txt

@@ -2,7 +2,12 @@ PBIAS internal regulator for SD card dual voltage i/o pads on OMAP SoCs.
 
 Required properties:
 - compatible:
-  - "ti,pbias-omap" for OMAP2, OMAP3, OMAP4, OMAP5, DRA7.
+  - should be "ti,pbias-dra7" for DRA7
+  - should be "ti,pbias-omap2" for OMAP2
+  - should be "ti,pbias-omap3" for OMAP3
+  - should be "ti,pbias-omap4" for OMAP4
+  - should be "ti,pbias-omap5" for OMAP5
+  - "ti,pbias-omap" is deprecated
 - reg: pbias register offset from syscon base and size of pbias register.
 - syscon : phandle of the system control module
 - regulator-name : should be

Documentation/devicetree/bindings/spi/spi-mt65xx.txt

@@ -15,17 +15,18 @@ Required properties:
 - interrupts: Should contain spi interrupt
 
 - clocks: phandles to input clocks.
-  The first should be <&topckgen CLK_TOP_SPI_SEL>.
-  The second should be one of the following.
+  The first should be one of the following. It's PLL.
    -  <&clk26m>: specify parent clock 26MHZ.
    -  <&topckgen CLK_TOP_SYSPLL3_D2>: specify parent clock 109MHZ.
 				      It's the default one.
    -  <&topckgen CLK_TOP_SYSPLL4_D2>: specify parent clock 78MHZ.
    -  <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ.
    -  <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ.
+  The second should be <&topckgen CLK_TOP_SPI_SEL>. It's clock mux.
+  The third is <&pericfg CLK_PERI_SPI0>. It's clock gate.
 
-- clock-names: shall be "spi-clk" for the controller clock, and
-  "parent-clk" for the parent clock.
+- clock-names: shall be "parent-clk" for the parent clock, "sel-clk" for the
+  muxes clock, and "spi-clk" for the clock gate.
 
 Optional properties:
 - mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi
@@ -44,8 +45,11 @@ spi: spi@1100a000 {
 	#size-cells = <0>;
 	reg = <0 0x1100a000 0 0x1000>;
 	interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>;
-	clocks = <&topckgen CLK_TOP_SPI_SEL>, <&topckgen CLK_TOP_SYSPLL3_D2>;
-	clock-names = "spi-clk", "parent-clk";
+	clocks = <&topckgen CLK_TOP_SYSPLL3_D2>,
+		 <&topckgen CLK_TOP_SPI_SEL>,
+		 <&pericfg CLK_PERI_SPI0>;
+	clock-names = "parent-clk", "sel-clk", "spi-clk";
+
 	mediatek,pad-select = <0>;
 	status = "disabled";
 };

Documentation/devicetree/bindings/thermal/thermal.txt

@@ -55,19 +55,11 @@ of heat dissipation). For example a fan's cooling states correspond to
 the different fan speeds possible. Cooling states are referred to by
 single unsigned integers, where larger numbers mean greater heat
 dissipation. The precise set of cooling states associated with a device
-(as referred to be the cooling-min-state and cooling-max-state
+(as referred to by the cooling-min-level and cooling-max-level
 properties) should be defined in a particular device's binding.
 For more examples of cooling devices, refer to the example sections below.
 
 Required properties:
-- cooling-min-state:	An integer indicating the smallest
-  Type: unsigned	cooling state accepted. Typically 0.
-  Size: one cell
-
-- cooling-max-state:	An integer indicating the largest
-  Type: unsigned	cooling state accepted.
-  Size: one cell
-
 - #cooling-cells:	Used to provide cooling device specific information
   Type: unsigned	while referring to it. Must be at least 2, in order
   Size: one cell      	to specify minimum and maximum cooling state used
@@ -77,6 +69,15 @@ Required properties:
 			See Cooling device maps section below for more details
 			on how consumers refer to cooling devices.
 
+Optional properties:
+- cooling-min-level:	An integer indicating the smallest
+  Type: unsigned	cooling state accepted. Typically 0.
+  Size: one cell
+
+- cooling-max-level:	An integer indicating the largest
+  Type: unsigned	cooling state accepted.
+  Size: one cell
+
 * Trip points
 
 The trip node is a node to describe a point in the temperature domain
@@ -225,8 +226,8 @@ cpus {
 			396000  950000
 			198000  850000
 		>;
-		cooling-min-state = <0>;
-		cooling-max-state = <3>;
+		cooling-min-level = <0>;
+		cooling-max-level = <3>;
 		#cooling-cells = <2>; /* min followed by max */
 	};
 	...
@@ -240,8 +241,8 @@ cpus {
 	 */
 	fan0: fan@0x48 {
 		...
-		cooling-min-state = <0>;
-		cooling-max-state = <9>;
+		cooling-min-level = <0>;
+		cooling-max-level = <9>;
 		#cooling-cells = <2>; /* min followed by max */
 	};
 };

Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt

@@ -6,6 +6,7 @@ Required properties:
 	"lsi,zevio-usb"
 	"qcom,ci-hdrc"
 	"chipidea,usb2"
+	"xlnx,zynq-usb-2.20a"
 - reg: base address and length of the registers
 - interrupts: interrupt for the USB controller
 

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -203,6 +203,7 @@ sitronix	Sitronix Technology Corporation
 skyworks	Skyworks Solutions, Inc.
 smsc	Standard Microsystems Corporation
 snps	Synopsys, Inc.
+socionext	Socionext Inc.
 solidrun	SolidRun
 solomon        Solomon Systech Limited
 sony	Sony Corporation

Documentation/input/multi-touch-protocol.txt

@@ -361,7 +361,7 @@ For win8 devices with both T and C coordinates, the position mapping is
    ABS_MT_POSITION_X := T_X
    ABS_MT_POSITION_Y := T_Y
    ABS_MT_TOOL_X := C_X
-   ABS_MT_TOOL_X := C_Y
+   ABS_MT_TOOL_Y := C_Y
 
 Unfortunately, there is not enough information to specify both the touching
 ellipse and the tool ellipse, so one has to resort to approximations.  One

Documentation/networking/vrf.txt

@@ -0,0 +1,96 @@
+Virtual Routing and Forwarding (VRF)
+====================================
+The VRF device combined with ip rules provides the ability to create virtual
+routing and forwarding domains (aka VRFs, VRF-lite to be specific) in the
+Linux network stack. One use case is the multi-tenancy problem where each
+tenant has their own unique routing tables and in the very least need
+different default gateways.
+
+Processes can be "VRF aware" by binding a socket to the VRF device. Packets
+through the socket then use the routing table associated with the VRF
+device. An important feature of the VRF device implementation is that it
+impacts only Layer 3 and above so L2 tools (e.g., LLDP) are not affected
+(ie., they do not need to be run in each VRF). The design also allows
+the use of higher priority ip rules (Policy Based Routing, PBR) to take
+precedence over the VRF device rules directing specific traffic as desired.
+
+In addition, VRF devices allow VRFs to be nested within namespaces. For
+example network namespaces provide separation of network interfaces at L1
+(Layer 1 separation), VLANs on the interfaces within a namespace provide
+L2 separation and then VRF devices provide L3 separation.
+
+Design
+------
+A VRF device is created with an associated route table. Network interfaces
+are then enslaved to a VRF device:
+
+         +-----------------------------+
+         |           vrf-blue          |  ===> route table 10
+         +-----------------------------+
+            |        |            |
+         +------+ +------+     +-------------+
+         | eth1 | | eth2 | ... |    bond1    |
+         +------+ +------+     +-------------+
+                                  |       |
+                              +------+ +------+
+                              | eth8 | | eth9 |
+                              +------+ +------+
+
+Packets received on an enslaved device and are switched to the VRF device
+using an rx_handler which gives the impression that packets flow through
+the VRF device. Similarly on egress routing rules are used to send packets
+to the VRF device driver before getting sent out the actual interface. This
+allows tcpdump on a VRF device to capture all packets into and out of the
+VRF as a whole.[1] Similiarly, netfilter [2] and tc rules can be applied
+using the VRF device to specify rules that apply to the VRF domain as a whole.
+
+[1] Packets in the forwarded state do not flow through the device, so those
+    packets are not seen by tcpdump. Will revisit this limitation in a
+    future release.
+
+[2] Iptables on ingress is limited to NF_INET_PRE_ROUTING only with skb->dev
+    set to real ingress device and egress is limited to NF_INET_POST_ROUTING.
+    Will revisit this limitation in a future release.
+
+
+Setup
+-----
+1. VRF device is created with an association to a FIB table.
+   e.g, ip link add vrf-blue type vrf table 10
+        ip link set dev vrf-blue up
+
+2. Rules are added that send lookups to the associated FIB table when the
+   iif or oif is the VRF device. e.g.,
+       ip ru add oif vrf-blue table 10
+       ip ru add iif vrf-blue table 10
+
+   Set the default route for the table (and hence default route for the VRF).
+   e.g, ip route add table 10 prohibit default
+
+3. Enslave L3 interfaces to a VRF device.
+   e.g,  ip link set dev eth1 master vrf-blue
+
+   Local and connected routes for enslaved devices are automatically moved to
+   the table associated with VRF device. Any additional routes depending on
+   the enslaved device will need to be reinserted following the enslavement.
+
+4. Additional VRF routes are added to associated table.
+   e.g., ip route add table 10 ...
+
+
+Applications
+------------
+Applications that are to work within a VRF need to bind their socket to the
+VRF device:
+
+    setsockopt(sd, SOL_SOCKET, SO_BINDTODEVICE, dev, strlen(dev)+1);
+
+or to specify the output device using cmsg and IP_PKTINFO.
+
+
+Limitations
+-----------
+VRF device currently only works for IPv4. Support for IPv6 is under development.
+
+Index of original ingress interface is not available via cmsg. Will address
+soon.

Documentation/power/pci.txt

@@ -979,20 +979,45 @@ every time right after the runtime_resume() callback has returned
 (alternatively, the runtime_suspend() callback will have to check if the
 device should really be suspended and return -EAGAIN if that is not the case).
 
-The runtime PM of PCI devices is disabled by default.  It is also blocked by
-pci_pm_init() that runs the pm_runtime_forbid() helper function.  If a PCI
-driver implements the runtime PM callbacks and intends to use the runtime PM
-framework provided by the PM core and the PCI subsystem, it should enable this
-feature by executing the pm_runtime_enable() helper function.  However, the
-driver should not call the pm_runtime_allow() helper function unblocking
-the runtime PM of the device.  Instead, it should allow user space or some
-platform-specific code to do that (user space can do it via sysfs), although
-once it has called pm_runtime_enable(), it must be prepared to handle the
+The runtime PM of PCI devices is enabled by default by the PCI core.  PCI
+device drivers do not need to enable it and should not attempt to do so.
+However, it is blocked by pci_pm_init() that runs the pm_runtime_forbid()
+helper function.  In addition to that, the runtime PM usage counter of
+each PCI device is incremented by local_pci_probe() before executing the
+probe callback provided by the device's driver.
+
+If a PCI driver implements the runtime PM callbacks and intends to use the
+runtime PM framework provided by the PM core and the PCI subsystem, it needs
+to decrement the device's runtime PM usage counter in its probe callback
+function.  If it doesn't do that, the counter will always be different from
+zero for the device and it will never be runtime-suspended.  The simplest
+way to do that is by calling pm_runtime_put_noidle(), but if the driver
+wants to schedule an autosuspend right away, for example, it may call
+pm_runtime_put_autosuspend() instead for this purpose.  Generally, it
+just needs to call a function that decrements the devices usage counter
+from its probe routine to make runtime PM work for the device.
+
+It is important to remember that the driver's runtime_suspend() callback
+may be executed right after the usage counter has been decremented, because
+user space may already have cuased the pm_runtime_allow() helper function
+unblocking the runtime PM of the device to run via sysfs, so the driver must
+be prepared to cope with that.
+
+The driver itself should not call pm_runtime_allow(), though.  Instead, it
+should let user space or some platform-specific code do that (user space can
+do it via sysfs as stated above), but it must be prepared to handle the
 runtime PM of the device correctly as soon as pm_runtime_allow() is called
-(which may happen at any time).  [It also is possible that user space causes
-pm_runtime_allow() to be called via sysfs before the driver is loaded, so in
-fact the driver has to be prepared to handle the runtime PM of the device as
-soon as it calls pm_runtime_enable().]
+(which may happen at any time, even before the driver is loaded).
+
+When the driver's remove callback runs, it has to balance the decrementation
+of the device's runtime PM usage counter at the probe time.  For this reason,
+if it has decremented the counter in its probe callback, it must run
+pm_runtime_get_noresume() in its remove callback.  [Since the core carries
+out a runtime resume of the device and bumps up the device's usage counter
+before running the driver's remove callback, the runtime PM of the device
+is effectively disabled for the duration of the remove execution and all
+runtime PM helper functions incrementing the device's usage counter are
+then effectively equivalent to pm_runtime_get_noresume().]
 
 The runtime PM framework works by processing requests to suspend or resume
 devices, or to check if they are idle (in which cases it is reasonable to

Documentation/ptp/testptp.c

@@ -18,6 +18,7 @@
  *  Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
  */
 #define _GNU_SOURCE
+#define __SANE_USERSPACE_TYPES__        /* For PPC64, to get LL64 types */
 #include <errno.h>
 #include <fcntl.h>
 #include <inttypes.h>

Documentation/sysctl/net.txt

@@ -54,13 +54,15 @@ default_qdisc
 --------------
 
 The default queuing discipline to use for network devices. This allows
-overriding the default queue discipline of pfifo_fast with an
-alternative. Since the default queuing discipline is created with the
-no additional parameters so is best suited to queuing disciplines that
-work well without configuration like stochastic fair queue (sfq),
-CoDel (codel) or fair queue CoDel (fq_codel). Don't use queuing disciplines
-like Hierarchical Token Bucket or Deficit Round Robin which require setting
-up classes and bandwidths.
+overriding the default of pfifo_fast with an alternative. Since the default
+queuing discipline is created without additional parameters so is best suited
+to queuing disciplines that work well without configuration like stochastic
+fair queue (sfq), CoDel (codel) or fair queue CoDel (fq_codel). Don't use
+queuing disciplines like Hierarchical Token Bucket or Deficit Round Robin
+which require setting up classes and bandwidths. Note that physical multiqueue
+interfaces still use mq as root qdisc, which in turn uses this default for its
+leaves. Virtual devices (like e.g. lo or veth) ignore this setting and instead
+default to noqueue.
 Default: pfifo_fast
 
 busy_read

Documentation/thermal/power_allocator.txt

@@ -4,7 +4,7 @@ Power allocator governor tunables
 Trip points
 -----------
 
-The governor requires the following two passive trip points:
+The governor works optimally with the following two passive trip points:
 
 1.  "switch on" trip point: temperature above which the governor
     control loop starts operating.  This is the first passive trip

MAINTAINERS

@@ -615,9 +615,8 @@ F:	Documentation/hwmon/fam15h_power
 F:	drivers/hwmon/fam15h_power.c
 
 AMD GEODE CS5536 USB DEVICE CONTROLLER DRIVER
-M:	Thomas Dahlmann <dahlmann.thomas@arcor.de>
 L:	linux-geode@lists.infradead.org (moderated for non-subscribers)
-S:	Supported
+S:	Orphan
 F:	drivers/usb/gadget/udc/amd5536udc.*
 
 AMD GEODE PROCESSOR/CHIPSET SUPPORT
@@ -808,6 +807,13 @@ S:	Maintained
 F:	drivers/video/fbdev/arcfb.c
 F:	drivers/video/fbdev/core/fb_defio.c
 
+ARCNET NETWORK LAYER
+M:	Michael Grzeschik <m.grzeschik@pengutronix.de>
+L:	netdev@vger.kernel.org
+S:	Maintained
+F:	drivers/net/arcnet/
+F:	include/uapi/linux/if_arcnet.h
+
 ARM MFM AND FLOPPY DRIVERS
 M:	Ian Molton <spyro@f2s.com>
 S:	Maintained
@@ -3394,7 +3400,6 @@ F:	drivers/staging/dgnc/
 
 DIGI EPCA PCI PRODUCTS
 M:	Lidza Louina <lidza.louina@gmail.com>
-M:	Mark Hounschell <markh@compro.net>
 M:	Daeseok Youn <daeseok.youn@gmail.com>
 L:	driverdev-devel@linuxdriverproject.org
 S:	Maintained
@@ -5952,7 +5957,7 @@ F:	virt/kvm/
 KERNEL VIRTUAL MACHINE (KVM) FOR AMD-V
 M:	Joerg Roedel <joro@8bytes.org>
 L:	kvm@vger.kernel.org
-W:	http://kvm.qumranet.com
+W:	http://www.linux-kvm.org/
 S:	Maintained
 F:	arch/x86/include/asm/svm.h
 F:	arch/x86/kvm/svm.c
@@ -5960,7 +5965,7 @@ F:	arch/x86/kvm/svm.c
 KERNEL VIRTUAL MACHINE (KVM) FOR POWERPC
 M:	Alexander Graf <agraf@suse.com>
 L:	kvm-ppc@vger.kernel.org
-W:	http://kvm.qumranet.com
+W:	http://www.linux-kvm.org/
 T:	git git://github.com/agraf/linux-2.6.git
 S:	Supported
 F:	arch/powerpc/include/asm/kvm*
@@ -8500,7 +8505,6 @@ F:	Documentation/networking/LICENSE.qla3xxx
 F:	drivers/net/ethernet/qlogic/qla3xxx.*
 
 QLOGIC QLCNIC (1/10)Gb ETHERNET DRIVER
-M:	Shahed Shaikh <shahed.shaikh@qlogic.com>
 M:	Dept-GELinuxNICDev@qlogic.com
 L:	netdev@vger.kernel.org
 S:	Supported
@@ -9904,8 +9908,8 @@ F:	drivers/staging/media/lirc/
 STAGING - LUSTRE PARALLEL FILESYSTEM
 M:	Oleg Drokin <oleg.drokin@intel.com>
 M:	Andreas Dilger <andreas.dilger@intel.com>
-L:	HPDD-discuss@lists.01.org (moderated for non-subscribers)
-W:	http://lustre.opensfs.org/
+L:	lustre-devel@lists.lustre.org (moderated for non-subscribers)
+W:	http://wiki.lustre.org/
 S:	Maintained
 F:	drivers/staging/lustre
 
@@ -10338,6 +10342,16 @@ F:	include/uapi/linux/thermal.h
 F:	include/linux/cpu_cooling.h
 F:	Documentation/devicetree/bindings/thermal/
 
+THERMAL/CPU_COOLING
+M:	Amit Daniel Kachhap <amit.kachhap@gmail.com>
+M:	Viresh Kumar <viresh.kumar@linaro.org>
+M:	Javi Merino <javi.merino@arm.com>
+L:	linux-pm@vger.kernel.org
+S:	Supported
+F:	Documentation/thermal/cpu-cooling-api.txt
+F:	drivers/thermal/cpu_cooling.c
+F:	include/linux/cpu_cooling.h
+
 THINGM BLINK(1) USB RGB LED DRIVER
 M:	Vivien Didelot <vivien.didelot@savoirfairelinux.com>
 S:	Maintained
@@ -11187,7 +11201,7 @@ F:	drivers/vlynq/vlynq.c
 F:	include/linux/vlynq.h
 
 VME SUBSYSTEM
-M:	Martyn Welch <martyn.welch@ge.com>
+M:	Martyn Welch <martyn@welchs.me.uk>
 M:	Manohar Vanga <manohar.vanga@gmail.com>
 M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 L:	devel@driverdev.osuosl.org
@@ -11239,7 +11253,6 @@ VOLTAGE AND CURRENT REGULATOR FRAMEWORK
 M:	Liam Girdwood <lgirdwood@gmail.com>
 M:	Mark Brown <broonie@kernel.org>
 L:	linux-kernel@vger.kernel.org
-W:	http://opensource.wolfsonmicro.com/node/15
 W:	http://www.slimlogic.co.uk/?p=48
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git
 S:	Supported
@@ -11253,6 +11266,7 @@ L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/vrf.c
 F:	include/net/vrf.h
+F:	Documentation/networking/vrf.txt
 
 VT1211 HARDWARE MONITOR DRIVER
 M:	Juerg Haefliger <juergh@gmail.com>
@@ -11368,17 +11382,15 @@ WM97XX TOUCHSCREEN DRIVERS
 M:	Mark Brown <broonie@kernel.org>
 M:	Liam Girdwood <lrg@slimlogic.co.uk>
 L:	linux-input@vger.kernel.org
-T:	git git://opensource.wolfsonmicro.com/linux-2.6-touch
-W:	http://opensource.wolfsonmicro.com/node/7
+W:	https://github.com/CirrusLogic/linux-drivers/wiki
 S:	Supported
 F:	drivers/input/touchscreen/*wm97*
 F:	include/linux/wm97xx.h
 
 WOLFSON MICROELECTRONICS DRIVERS
 L:	patches@opensource.wolfsonmicro.com
-T:	git git://opensource.wolfsonmicro.com/linux-2.6-asoc
-T:	git git://opensource.wolfsonmicro.com/linux-2.6-audioplus
-W:	http://opensource.wolfsonmicro.com/content/linux-drivers-wolfson-devices
+T:	git https://github.com/CirrusLogic/linux-drivers.git
+W:	https://github.com/CirrusLogic/linux-drivers/wiki
 S:	Supported
 F:	Documentation/hwmon/wm83??
 F:	arch/arm/mach-s3c64xx/mach-crag6410*

Makefile

@@ -1,7 +1,7 @@
 VERSION = 4
 PATCHLEVEL = 3
 SUBLEVEL = 0
-EXTRAVERSION = -rc1
+EXTRAVERSION = -rc4
 NAME = Hurr durr I'ma sheep
 
 # *DOCUMENTATION*

arch/alpha/kernel/irq.c

@@ -117,6 +117,6 @@ handle_irq(int irq)
 	}
 
 	irq_enter();
-	generic_handle_irq_desc(irq, desc);
+	generic_handle_irq_desc(desc);
 	irq_exit();
 }

arch/alpha/kernel/pci.c

@@ -242,7 +242,12 @@ pci_restore_srm_config(void)
 
 void pcibios_fixup_bus(struct pci_bus *bus)
 {
-	struct pci_dev *dev;
+	struct pci_dev *dev = bus->self;
+
+	if (pci_has_flag(PCI_PROBE_ONLY) && dev &&
+	    (dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) {
+		pci_read_bridge_bases(bus);
+	}
 
 	list_for_each_entry(dev, &bus->devices, bus_list) {
 		pdev_save_srm_config(dev);

arch/arc/include/asm/Kbuild

@@ -48,4 +48,5 @@ generic-y += types.h
 generic-y += ucontext.h
 generic-y += user.h
 generic-y += vga.h
+generic-y += word-at-a-time.h
 generic-y += xor.h

arch/arc/kernel/mcip.c

@@ -252,7 +252,7 @@ static struct irq_chip idu_irq_chip = {
 
 static int idu_first_irq;
 
-static void idu_cascade_isr(unsigned int __core_irq, struct irq_desc *desc)
+static void idu_cascade_isr(struct irq_desc *desc)
 {
 	struct irq_domain *domain = irq_desc_get_handler_data(desc);
 	unsigned int core_irq = irq_desc_get_irq(desc);

arch/arm/boot/dts/am335x-phycore-som.dtsi

@@ -252,10 +252,10 @@
 		};
 
 		vdd1_reg: regulator@2 {
-			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
+			/* VDD_MPU voltage limits 0.95V - 1.325V with +/-4% tolerance */
 			regulator-name = "vdd_mpu";
 			regulator-min-microvolt = <912500>;
-			regulator-max-microvolt = <1312500>;
+			regulator-max-microvolt = <1378000>;
 			regulator-boot-on;
 			regulator-always-on;
 		};

arch/arm/boot/dts/am57xx-beagle-x15.dts

@@ -98,13 +98,6 @@
 		pinctrl-0 = <&extcon_usb1_pins>;
 	};
 
-	extcon_usb2: extcon_usb2 {
-		compatible = "linux,extcon-usb-gpio";
-		id-gpio = <&gpio7 24 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&extcon_usb2_pins>;
-	};
-
 	hdmi0: connector {
 		compatible = "hdmi-connector";
 		label = "hdmi";
@@ -326,12 +319,6 @@
 		>;
 	};
 
-	extcon_usb2_pins: extcon_usb2_pins {
-		pinctrl-single,pins = <
-			0x3e8 (PIN_INPUT_PULLUP | MUX_MODE14) /* uart1_ctsn.gpio7_24 */
-		>;
-	};
-
 	tpd12s015_pins: pinmux_tpd12s015_pins {
 		pinctrl-single,pins = <
 			0x3b0 (PIN_OUTPUT | MUX_MODE14)		/* gpio7_10 CT_CP_HPD */
@@ -432,7 +419,7 @@
 				};
 
 				ldo3_reg: ldo3 {
-					/* VDDA_1V8_PHY */
+					/* VDDA_1V8_PHYA */
 					regulator-name = "ldo3";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
@@ -440,6 +427,15 @@
 					regulator-boot-on;
 				};
 
+				ldo4_reg: ldo4 {
+					/* VDDA_1V8_PHYB */
+					regulator-name = "ldo4";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
 				ldo9_reg: ldo9 {
 					/* VDD_RTC */
 					regulator-name = "ldo9";
@@ -495,6 +491,14 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 		};
+
+		extcon_usb2: tps659038_usb {
+			compatible = "ti,palmas-usb-vid";
+			ti,enable-vbus-detection;
+			ti,enable-id-detection;
+			id-gpios = <&gpio7 24 GPIO_ACTIVE_HIGH>;
+		};
+
 	};
 
 	tmp102: tmp102@48 {
@@ -517,7 +521,8 @@
 	mcp_rtc: rtc@6f {
 		compatible = "microchip,mcp7941x";
 		reg = <0x6f>;
-		interrupts = <GIC_SPI 2 IRQ_TYPE_EDGE_RISING>;  /* IRQ_SYS_1N */
+		interrupts-extended = <&crossbar_mpu GIC_SPI 2 IRQ_TYPE_EDGE_RISING>,
+				      <&dra7_pmx_core 0x424>;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&mcp79410_pins_default>;
@@ -579,7 +584,6 @@
 	pinctrl-0 = <&mmc1_pins_default>;
 
 	vmmc-supply = <&ldo1_reg>;
-	vmmc_aux-supply = <&vdd_3v3>;
 	bus-width = <4>;
 	cd-gpios = <&gpio6 27 0>; /* gpio 219 */
 };
@@ -623,6 +627,14 @@
 };
 
 &usb2 {
+	/*
+	 * Stand alone usage is peripheral only.
+	 * However, with some resistor modifications
+	 * this port can be used via expansion connectors
+	 * as "host" or "dual-role". If so, provide
+	 * the necessary dr_mode override in the expansion
+	 * board's DT.
+	 */
 	dr_mode = "peripheral";
 };
 
@@ -681,7 +693,7 @@
 
 &hdmi {
 	status = "ok";
-	vdda-supply = <&ldo3_reg>;
+	vdda-supply = <&ldo4_reg>;
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&hdmi_pins>;

arch/arm/boot/dts/dm8148-evm.dts

@@ -19,10 +19,10 @@
 
 &cpsw_emac0 {
 	phy_id = <&davinci_mdio>, <0>;
-	phy-mode = "mii";
+	phy-mode = "rgmii";
 };
 
 &cpsw_emac1 {
 	phy_id = <&davinci_mdio>, <1>;
-	phy-mode = "mii";
+	phy-mode = "rgmii";
 };

arch/arm/boot/dts/dm8148-t410.dts

@@ -8,7 +8,7 @@
 #include "dm814x.dtsi"
 
 / {
-	model = "DM8148 EVM";
+	model = "HP t410 Smart Zero Client";
 	compatible = "hp,t410", "ti,dm8148";
 
 	memory {
@@ -19,10 +19,10 @@
 
 &cpsw_emac0 {
 	phy_id = <&davinci_mdio>, <0>;
-	phy-mode = "mii";
+	phy-mode = "rgmii";
 };
 
 &cpsw_emac1 {
 	phy_id = <&davinci_mdio>, <1>;
-	phy-mode = "mii";
+	phy-mode = "rgmii";
 };

arch/arm/boot/dts/dm814x.dtsi

@@ -181,9 +181,9 @@
 				ti,hwmods = "timer3";
 			};
 
-			control: control@160000 {
+			control: control@140000 {
 				compatible = "ti,dm814-scm", "simple-bus";
-				reg = <0x160000 0x16d000>;
+				reg = <0x140000 0x16d000>;
 				#address-cells = <1>;
 				#size-cells = <1>;
 				ranges = <0 0x160000 0x16d000>;
@@ -321,9 +321,9 @@
 				mac-address = [ 00 00 00 00 00 00 ];
 			};
 
-			phy_sel: cpsw-phy-sel@0x48160650 {
+			phy_sel: cpsw-phy-sel@48140650 {
 				compatible = "ti,am3352-cpsw-phy-sel";
-				reg= <0x48160650 0x4>;
+				reg= <0x48140650 0x4>;
 				reg-names = "gmii-sel";
 			};
 		};

arch/arm/boot/dts/dra7.dtsi

@@ -120,9 +120,10 @@
 					reg = <0x0 0x1400>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x0 0x1400>;
 
 					pbias_regulator: pbias_regulator {
-						compatible = "ti,pbias-omap";
+						compatible = "ti,pbias-dra7", "ti,pbias-omap";
 						reg = <0xe00 0x4>;
 						syscon = <&scm_conf>;
 						pbias_mmc_reg: pbias_mmc_omap5 {
@@ -1417,7 +1418,7 @@
 			ti,irqs-safe-map = <0>;
 		};
 
-		mac: ethernet@4a100000 {
+		mac: ethernet@48484000 {
 			compatible = "ti,dra7-cpsw","ti,cpsw";
 			ti,hwmods = "gmac";
 			clocks = <&dpll_gmac_ck>, <&gmac_gmii_ref_clk_div>;

arch/arm/boot/dts/omap2430.dtsi

@@ -56,6 +56,7 @@
 					reg = <0x270 0x240>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x270 0x240>;
 
 					scm_clocks: clocks {
 						#address-cells = <1>;
@@ -63,7 +64,7 @@
 					};
 
 					pbias_regulator: pbias_regulator {
-						compatible = "ti,pbias-omap";
+						compatible = "ti,pbias-omap2", "ti,pbias-omap";
 						reg = <0x230 0x4>;
 						syscon = <&scm_conf>;
 						pbias_mmc_reg: pbias_mmc_omap2430 {

arch/arm/boot/dts/omap3-beagle.dts

@@ -202,7 +202,7 @@
 
 	tfp410_pins: pinmux_tfp410_pins {
 		pinctrl-single,pins = <
-			0x194 (PIN_OUTPUT | MUX_MODE4)	/* hdq_sio.gpio_170 */
+			0x196 (PIN_OUTPUT | MUX_MODE4)	/* hdq_sio.gpio_170 */
 		>;
 	};
 

arch/arm/boot/dts/omap3-igep.dtsi

@@ -78,12 +78,6 @@
 		>;
 	};
 
-	smsc9221_pins: pinmux_smsc9221_pins {
-		pinctrl-single,pins = <
-			0x1a2 (PIN_INPUT | MUX_MODE4)		/* mcspi1_cs2.gpio_176 */
-		>;
-	};
-
 	i2c1_pins: pinmux_i2c1_pins {
 		pinctrl-single,pins = <
 			0x18a (PIN_INPUT | MUX_MODE0)   /* i2c1_scl.i2c1_scl */

arch/arm/boot/dts/omap3-igep0020-common.dtsi

@@ -156,6 +156,12 @@
 			OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0)	/* uart2_rx.uart2_rx */
 		>;
 	};
+
+	smsc9221_pins: pinmux_smsc9221_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT | MUX_MODE4)	/* mcspi1_cs2.gpio_176 */
+		>;
+	};
 };
 
 &omap3_pmx_core2 {

arch/arm/boot/dts/omap3.dtsi

@@ -113,10 +113,22 @@
 				};
 
 				scm_conf: scm_conf@270 {
-					compatible = "syscon";
+					compatible = "syscon", "simple-bus";
 					reg = <0x270 0x330>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x270 0x330>;
+
+					pbias_regulator: pbias_regulator {
+						compatible = "ti,pbias-omap3", "ti,pbias-omap";
+						reg = <0x2b0 0x4>;
+						syscon = <&scm_conf>;
+						pbias_mmc_reg: pbias_mmc_omap2430 {
+							regulator-name = "pbias_mmc_omap2430";
+							regulator-min-microvolt = <1800000>;
+							regulator-max-microvolt = <3000000>;
+						};
+					};
 
 					scm_clocks: clocks {
 						#address-cells = <1>;
@@ -202,17 +214,6 @@
 			dma-requests = <96>;
 		};
 
-		pbias_regulator: pbias_regulator {
-			compatible = "ti,pbias-omap";
-			reg = <0x2b0 0x4>;
-			syscon = <&scm_conf>;
-			pbias_mmc_reg: pbias_mmc_omap2430 {
-				regulator-name = "pbias_mmc_omap2430";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3000000>;
-			};
-		};
-
 		gpio1: gpio@48310000 {
 			compatible = "ti,omap3-gpio";
 			reg = <0x48310000 0x200>;

arch/arm/boot/dts/omap4.dtsi

@@ -196,9 +196,10 @@
 					reg = <0x5a0 0x170>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x5a0 0x170>;
 
 					pbias_regulator: pbias_regulator {
-						compatible = "ti,pbias-omap";
+						compatible = "ti,pbias-omap4", "ti,pbias-omap";
 						reg = <0x60 0x4>;
 						syscon = <&omap4_padconf_global>;
 						pbias_mmc_reg: pbias_mmc_omap4 {

arch/arm/boot/dts/omap5-uevm.dts

@@ -174,8 +174,8 @@
 
 	i2c5_pins: pinmux_i2c5_pins {
 		pinctrl-single,pins = <
-			0x184 (PIN_INPUT | MUX_MODE0)		/* i2c5_scl */
-			0x186 (PIN_INPUT | MUX_MODE0)		/* i2c5_sda */
+			0x186 (PIN_INPUT | MUX_MODE0)		/* i2c5_scl */
+			0x188 (PIN_INPUT | MUX_MODE0)		/* i2c5_sda */
 		>;
 	};
 

arch/arm/boot/dts/omap5.dtsi

@@ -185,9 +185,10 @@
 					reg = <0x5a0 0xec>;
 					#address-cells = <1>;
 					#size-cells = <1>;
+					ranges = <0 0x5a0 0xec>;
 
 					pbias_regulator: pbias_regulator {
-						compatible = "ti,pbias-omap";
+						compatible = "ti,pbias-omap5", "ti,pbias-omap";
 						reg = <0x60 0x4>;
 						syscon = <&omap5_padconf_global>;
 						pbias_mmc_reg: pbias_mmc_omap5 {

arch/arm/boot/dts/rk3288-veyron.dtsi

@@ -158,6 +158,7 @@
 };
 
 &hdmi {
+	ddc-i2c-bus = <&i2c5>;
 	status = "okay";
 };
 

arch/arm/boot/dts/stih407.dtsi

@@ -103,48 +103,46 @@
 							 <&clk_s_d0_quadfs 0>,
 							 <&clk_s_d2_quadfs 0>,
 							 <&clk_s_d2_quadfs 0>;
-				ranges;
-
-				sti-hdmi@8d04000 {
-					compatible = "st,stih407-hdmi";
-					reg = <0x8d04000 0x1000>;
-					reg-names = "hdmi-reg";
-					interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>;
-					interrupt-names	= "irq";
-					clock-names = "pix",
-						      "tmds",
-						      "phy",
-						      "audio",
-						      "main_parent",
-						      "aux_parent";
-
-					clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
-						 <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
-						 <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
-						 <&clk_s_d0_flexgen CLK_PCM_0>,
-						 <&clk_s_d2_quadfs 0>,
-						 <&clk_s_d2_quadfs 1>;
-
-					hdmi,hpd-gpio = <&pio5 3>;
-					reset-names = "hdmi";
-					resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
-					ddc = <&hdmiddc>;
-
-				};
-
-				sti-hda@8d02000 {
-					compatible = "st,stih407-hda";
-					reg = <0x8d02000 0x400>, <0x92b0120 0x4>;
-					reg-names = "hda-reg", "video-dacs-ctrl";
-					clock-names = "pix",
-						      "hddac",
-						      "main_parent",
-						      "aux_parent";
-					clocks = <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
-						 <&clk_s_d2_flexgen CLK_HDDAC>,
-						 <&clk_s_d2_quadfs 0>,
-						 <&clk_s_d2_quadfs 1>;
-				};
+			};
+
+			sti-hdmi@8d04000 {
+				compatible = "st,stih407-hdmi";
+				reg = <0x8d04000 0x1000>;
+				reg-names = "hdmi-reg";
+				interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>;
+				interrupt-names	= "irq";
+				clock-names = "pix",
+					      "tmds",
+					      "phy",
+					      "audio",
+					      "main_parent",
+					      "aux_parent";
+
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
+					 <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
+					 <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
+					 <&clk_s_d0_flexgen CLK_PCM_0>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
+
+				hdmi,hpd-gpio = <&pio5 3>;
+				reset-names = "hdmi";
+				resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
+				ddc = <&hdmiddc>;
+			};
+
+			sti-hda@8d02000 {
+				compatible = "st,stih407-hda";
+				reg = <0x8d02000 0x400>, <0x92b0120 0x4>;
+				reg-names = "hda-reg", "video-dacs-ctrl";
+				clock-names = "pix",
+					      "hddac",
+					      "main_parent",
+					      "aux_parent";
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
+					 <&clk_s_d2_flexgen CLK_HDDAC>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
 			};
 		};
 	};

arch/arm/boot/dts/stih410.dtsi

@@ -178,48 +178,46 @@
 							 <&clk_s_d0_quadfs 0>,
 							 <&clk_s_d2_quadfs 0>,
 							 <&clk_s_d2_quadfs 0>;
-				ranges;
-
-				sti-hdmi@8d04000 {
-					compatible = "st,stih407-hdmi";
-					reg = <0x8d04000 0x1000>;
-					reg-names = "hdmi-reg";
-					interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>;
-					interrupt-names	= "irq";
-					clock-names = "pix",
-						      "tmds",
-						      "phy",
-						      "audio",
-						      "main_parent",
-						      "aux_parent";
-
-					clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
-						 <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
-						 <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
-						 <&clk_s_d0_flexgen CLK_PCM_0>,
-						 <&clk_s_d2_quadfs 0>,
-						 <&clk_s_d2_quadfs 1>;
-
-					hdmi,hpd-gpio = <&pio5 3>;
-					reset-names = "hdmi";
-					resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
-					ddc = <&hdmiddc>;
-
-				};
-
-				sti-hda@8d02000 {
-					compatible = "st,stih407-hda";
-					reg = <0x8d02000 0x400>, <0x92b0120 0x4>;
-					reg-names = "hda-reg", "video-dacs-ctrl";
-					clock-names = "pix",
-						      "hddac",
-						      "main_parent",
-						      "aux_parent";
-					clocks = <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
-						 <&clk_s_d2_flexgen CLK_HDDAC>,
-						 <&clk_s_d2_quadfs 0>,
-						 <&clk_s_d2_quadfs 1>;
-				};
+			};
+
+			sti-hdmi@8d04000 {
+				compatible = "st,stih407-hdmi";
+				reg = <0x8d04000 0x1000>;
+				reg-names = "hdmi-reg";
+				interrupts = <GIC_SPI 106 IRQ_TYPE_NONE>;
+				interrupt-names	= "irq";
+				clock-names = "pix",
+					      "tmds",
+					      "phy",
+					      "audio",
+					      "main_parent",
+					      "aux_parent";
+
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDMI>,
+					 <&clk_s_d2_flexgen CLK_TMDS_HDMI>,
+					 <&clk_s_d2_flexgen CLK_REF_HDMIPHY>,
+					 <&clk_s_d0_flexgen CLK_PCM_0>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
+
+				hdmi,hpd-gpio = <&pio5 3>;
+				reset-names = "hdmi";
+				resets = <&softreset STIH407_HDMI_TX_PHY_SOFTRESET>;
+				ddc = <&hdmiddc>;
+			};
+
+			sti-hda@8d02000 {
+				compatible = "st,stih407-hda";
+				reg = <0x8d02000 0x400>, <0x92b0120 0x4>;
+				reg-names = "hda-reg", "video-dacs-ctrl";
+				clock-names = "pix",
+					      "hddac",
+					      "main_parent",
+					      "aux_parent";
+				clocks = <&clk_s_d2_flexgen CLK_PIX_HDDAC>,
+					 <&clk_s_d2_flexgen CLK_HDDAC>,
+					 <&clk_s_d2_quadfs 0>,
+					 <&clk_s_d2_quadfs 1>;
 			};
 		};
 

arch/arm/common/it8152.c

@@ -95,7 +95,7 @@ void it8152_init_irq(void)
 	}
 }
 
-void it8152_irq_demux(unsigned int irq, struct irq_desc *desc)
+void it8152_irq_demux(struct irq_desc *desc)
 {
        int bits_pd, bits_lp, bits_ld;
        int i;

arch/arm/common/locomo.c

@@ -138,7 +138,7 @@ static struct locomo_dev_info locomo_devices[] = {
 	},
 };
 
-static void locomo_handler(unsigned int __irq, struct irq_desc *desc)
+static void locomo_handler(struct irq_desc *desc)
 {
 	struct locomo *lchip = irq_desc_get_chip_data(desc);
 	int req, i;

arch/arm/common/sa1111.c

@@ -196,10 +196,8 @@ static struct sa1111_dev_info sa1111_devices[] = {
  * active IRQs causes the interrupt output to pulse, the upper levels
  * will call us again if there are more interrupts to process.
  */
-static void
-sa1111_irq_handler(unsigned int __irq, struct irq_desc *desc)
+static void sa1111_irq_handler(struct irq_desc *desc)
 {
-	unsigned int irq = irq_desc_get_irq(desc);
 	unsigned int stat0, stat1, i;
 	struct sa1111 *sachip = irq_desc_get_handler_data(desc);
 	void __iomem *mapbase = sachip->base + SA1111_INTC;
@@ -214,7 +212,7 @@ sa1111_irq_handler(unsigned int __irq, struct irq_desc *desc)
 	sa1111_writel(stat1, mapbase + SA1111_INTSTATCLR1);
 
 	if (stat0 == 0 && stat1 == 0) {
-		do_bad_IRQ(irq, desc);
+		do_bad_IRQ(desc);
 		return;
 	}
 

arch/arm/configs/omap2plus_defconfig

@@ -240,7 +240,8 @@ CONFIG_SSI_PROTOCOL=m
 CONFIG_PINCTRL_SINGLE=y
 CONFIG_DEBUG_GPIO=y
 CONFIG_GPIO_SYSFS=y
-CONFIG_GPIO_PCF857X=m
+CONFIG_GPIO_PCA953X=m
+CONFIG_GPIO_PCF857X=y
 CONFIG_GPIO_TWL4030=y
 CONFIG_GPIO_PALMAS=y
 CONFIG_W1=m
@@ -350,6 +351,8 @@ CONFIG_USB_MUSB_HDRC=m
 CONFIG_USB_MUSB_OMAP2PLUS=m
 CONFIG_USB_MUSB_AM35X=m
 CONFIG_USB_MUSB_DSPS=m
+CONFIG_USB_INVENTRA_DMA=y
+CONFIG_USB_TI_CPPI41_DMA=y
 CONFIG_USB_DWC3=m
 CONFIG_USB_TEST=m
 CONFIG_AM335X_PHY_USB=y

arch/arm/include/asm/hardware/it8152.h

@@ -106,7 +106,7 @@ extern void __iomem *it8152_base_address;
 struct pci_dev;
 struct pci_sys_data;
 
-extern void it8152_irq_demux(unsigned int irq, struct irq_desc *desc);
+extern void it8152_irq_demux(struct irq_desc *desc);
 extern void it8152_init_irq(void);
 extern int it8152_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin);
 extern int it8152_pci_setup(int nr, struct pci_sys_data *sys);

arch/arm/include/asm/hw_irq.h

@@ -11,12 +11,6 @@ static inline void ack_bad_irq(int irq)
 	pr_crit("unexpected IRQ trap at vector %02x\n", irq);
 }
 
-void set_irq_flags(unsigned int irq, unsigned int flags);
-
-#define IRQF_VALID	(1 << 0)
-#define IRQF_PROBE	(1 << 1)
-#define IRQF_NOAUTOEN	(1 << 2)
-
 #define ARCH_IRQ_INIT_FLAGS	(IRQ_NOREQUEST | IRQ_NOPROBE)
 
 #endif

arch/arm/include/asm/kvm_host.h

@@ -29,21 +29,18 @@
 
 #define __KVM_HAVE_ARCH_INTC_INITIALIZED
 
-#if defined(CONFIG_KVM_ARM_MAX_VCPUS)
-#define KVM_MAX_VCPUS CONFIG_KVM_ARM_MAX_VCPUS
-#else
-#define KVM_MAX_VCPUS 0
-#endif
-
 #define KVM_USER_MEM_SLOTS 32
 #define KVM_PRIVATE_MEM_SLOTS 4
 #define KVM_COALESCED_MMIO_PAGE_OFFSET 1
 #define KVM_HAVE_ONE_REG
+#define KVM_HALT_POLL_NS_DEFAULT 500000
 
 #define KVM_VCPU_MAX_FEATURES 2
 
 #include <kvm/arm_vgic.h>
 
+#define KVM_MAX_VCPUS VGIC_V2_MAX_CPUS
+
 u32 *kvm_vcpu_reg(struct kvm_vcpu *vcpu, u8 reg_num, u32 mode);
 int __attribute_const__ kvm_target_cpu(void);
 int kvm_reset_vcpu(struct kvm_vcpu *vcpu);
@@ -148,6 +145,7 @@ struct kvm_vm_stat {
 
 struct kvm_vcpu_stat {
 	u32 halt_successful_poll;
+	u32 halt_attempted_poll;
 	u32 halt_wakeup;
 };
 

arch/arm/include/asm/mach/irq.h

@@ -23,10 +23,10 @@ extern int show_fiq_list(struct seq_file *, int);
 /*
  * This is for easy migration, but should be changed in the source
  */
-#define do_bad_IRQ(irq,desc)				\
+#define do_bad_IRQ(desc)				\
 do {							\
 	raw_spin_lock(&desc->lock);			\
-	handle_bad_irq(irq, desc);			\
+	handle_bad_irq(desc);				\
 	raw_spin_unlock(&desc->lock);			\
 } while(0)
 

arch/arm/include/asm/unistd.h

@@ -19,7 +19,7 @@
  * This may need to be greater than __NR_last_syscall+1 in order to
  * account for the padding in the syscall table
  */
-#define __NR_syscalls  (388)
+#define __NR_syscalls  (392)
 
 /*
  * *NOTE*: This is a ghost syscall private to the kernel.  Only the

arch/arm/include/uapi/asm/unistd.h

@@ -414,6 +414,8 @@
 #define __NR_memfd_create		(__NR_SYSCALL_BASE+385)
 #define __NR_bpf			(__NR_SYSCALL_BASE+386)
 #define __NR_execveat			(__NR_SYSCALL_BASE+387)
+#define __NR_userfaultfd		(__NR_SYSCALL_BASE+388)
+#define __NR_membarrier			(__NR_SYSCALL_BASE+389)
 
 /*
  * The following SWIs are ARM private.

arch/arm/kernel/calls.S

@@ -397,6 +397,8 @@
 /* 385 */	CALL(sys_memfd_create)
 		CALL(sys_bpf)
 		CALL(sys_execveat)
+		CALL(sys_userfaultfd)
+		CALL(sys_membarrier)
 #ifndef syscalls_counted
 .equ syscalls_padding, ((NR_syscalls + 3) & ~3) - NR_syscalls
 #define syscalls_counted

arch/arm/kernel/irq.c

@@ -79,26 +79,6 @@ asm_do_IRQ(unsigned int irq, struct pt_regs *regs)
 	handle_IRQ(irq, regs);
 }
 
-void set_irq_flags(unsigned int irq, unsigned int iflags)
-{
-	unsigned long clr = 0, set = IRQ_NOREQUEST | IRQ_NOPROBE | IRQ_NOAUTOEN;
-
-	if (irq >= nr_irqs) {
-		pr_err("Trying to set irq flags for IRQ%d\n", irq);
-		return;
-	}
-
-	if (iflags & IRQF_VALID)
-		clr |= IRQ_NOREQUEST;
-	if (iflags & IRQF_PROBE)
-		clr |= IRQ_NOPROBE;
-	if (!(iflags & IRQF_NOAUTOEN))
-		clr |= IRQ_NOAUTOEN;
-	/* Order is clear bits in "clr" then set bits in "set" */
-	irq_modify_status(irq, clr, set & ~clr);
-}
-EXPORT_SYMBOL_GPL(set_irq_flags);
-
 void __init init_IRQ(void)
 {
 	int ret;

arch/arm/kernel/kgdb.c

@@ -259,15 +259,17 @@ int kgdb_arch_set_breakpoint(struct kgdb_bkpt *bpt)
 	if (err)
 		return err;
 
-	patch_text((void *)bpt->bpt_addr,
-		   *(unsigned int *)arch_kgdb_ops.gdb_bpt_instr);
+	/* Machine is already stopped, so we can use __patch_text() directly */
+	__patch_text((void *)bpt->bpt_addr,
+		     *(unsigned int *)arch_kgdb_ops.gdb_bpt_instr);
 
 	return err;
 }
 
 int kgdb_arch_remove_breakpoint(struct kgdb_bkpt *bpt)
 {
-	patch_text((void *)bpt->bpt_addr, *(unsigned int *)bpt->saved_instr);
+	/* Machine is already stopped, so we can use __patch_text() directly */
+	__patch_text((void *)bpt->bpt_addr, *(unsigned int *)bpt->saved_instr);
 
 	return 0;
 }

arch/arm/kernel/signal.c

@@ -343,15 +343,18 @@ setup_return(struct pt_regs *regs, struct ksignal *ksig,
 		 */
 		thumb = handler & 1;
 
-#if __LINUX_ARM_ARCH__ >= 7
 		/*
-		 * Clear the If-Then Thumb-2 execution state
-		 * ARM spec requires this to be all 000s in ARM mode
-		 * Snapdragon S4/Krait misbehaves on a Thumb=>ARM
-		 * signal transition without this.
+		 * Clear the If-Then Thumb-2 execution state.  ARM spec
+		 * requires this to be all 000s in ARM mode.  Snapdragon
+		 * S4/Krait misbehaves on a Thumb=>ARM signal transition
+		 * without this.
+		 *
+		 * We must do this whenever we are running on a Thumb-2
+		 * capable CPU, which includes ARMv6T2.  However, we elect
+		 * to always do this to simplify the code; this field is
+		 * marked UNK/SBZP for older architectures.
 		 */
 		cpsr &= ~PSR_IT_MASK;
-#endif
 
 		if (thumb) {
 			cpsr |= PSR_T_BIT;

arch/arm/kvm/Kconfig

@@ -45,15 +45,4 @@ config KVM_ARM_HOST
 	---help---
 	  Provides host support for ARM processors.
 
-config KVM_ARM_MAX_VCPUS
-	int "Number maximum supported virtual CPUs per VM"
-	depends on KVM_ARM_HOST
-	default 4
-	help
-	  Static number of max supported virtual CPUs per VM.
-
-	  If you choose a high number, the vcpu structures will be quite
-	  large, so only choose a reasonable number that you expect to
-	  actually use.
-
 endif # VIRTUALIZATION

arch/arm/kvm/arm.c

@@ -446,7 +446,7 @@ static int kvm_vcpu_first_run_init(struct kvm_vcpu *vcpu)
 	 * Map the VGIC hardware resources before running a vcpu the first
 	 * time on this VM.
 	 */
-	if (unlikely(!vgic_ready(kvm))) {
+	if (unlikely(irqchip_in_kernel(kvm) && !vgic_ready(kvm))) {
 		ret = kvm_vgic_map_resources(kvm);
 		if (ret)
 			return ret;

arch/arm/kvm/interrupts_head.S

@@ -515,8 +515,7 @@ ARM_BE8(rev	r6, r6  )
 
 	mrc	p15, 0, r2, c14, c3, 1	@ CNTV_CTL
 	str	r2, [vcpu, #VCPU_TIMER_CNTV_CTL]
-	bic	r2, #1			@ Clear ENABLE
-	mcr	p15, 0, r2, c14, c3, 1	@ CNTV_CTL
+
 	isb
 
 	mrrc	p15, 3, rr_lo_hi(r2, r3), c14	@ CNTV_CVAL
@@ -529,6 +528,9 @@ ARM_BE8(rev	r6, r6  )
 	mcrr	p15, 4, r2, r2, c14	@ CNTVOFF
 
 1:
+	mov	r2, #0			@ Clear ENABLE
+	mcr	p15, 0, r2, c14, c3, 1	@ CNTV_CTL
+
 	@ Allow physical timer/counter access for the host
 	mrc	p15, 4, r2, c14, c1, 0	@ CNTHCTL
 	orr	r2, r2, #(CNTHCTL_PL1PCEN | CNTHCTL_PL1PCTEN)

arch/arm/kvm/mmu.c

@@ -1792,8 +1792,10 @@ int kvm_arch_prepare_memory_region(struct kvm *kvm,
 		if (vma->vm_flags & VM_PFNMAP) {
 			gpa_t gpa = mem->guest_phys_addr +
 				    (vm_start - mem->userspace_addr);
-			phys_addr_t pa = (vma->vm_pgoff << PAGE_SHIFT) +
-					 vm_start - vma->vm_start;
+			phys_addr_t pa;
+
+			pa = (phys_addr_t)vma->vm_pgoff << PAGE_SHIFT;
+			pa += vm_start - vma->vm_start;
 
 			/* IO region dirty page logging not allowed */
 			if (memslot->flags & KVM_MEM_LOG_DIRTY_PAGES)

arch/arm/kvm/psci.c

@@ -126,7 +126,7 @@ static unsigned long kvm_psci_vcpu_on(struct kvm_vcpu *source_vcpu)
 
 static unsigned long kvm_psci_vcpu_affinity_info(struct kvm_vcpu *vcpu)
 {
-	int i;
+	int i, matching_cpus = 0;
 	unsigned long mpidr;
 	unsigned long target_affinity;
 	unsigned long target_affinity_mask;
@@ -151,12 +151,16 @@ static unsigned long kvm_psci_vcpu_affinity_info(struct kvm_vcpu *vcpu)
 	 */
 	kvm_for_each_vcpu(i, tmp, kvm) {
 		mpidr = kvm_vcpu_get_mpidr_aff(tmp);
-		if (((mpidr & target_affinity_mask) == target_affinity) &&
-		    !tmp->arch.pause) {
-			return PSCI_0_2_AFFINITY_LEVEL_ON;
+		if ((mpidr & target_affinity_mask) == target_affinity) {
+			matching_cpus++;
+			if (!tmp->arch.pause)
+				return PSCI_0_2_AFFINITY_LEVEL_ON;
 		}
 	}
 
+	if (!matching_cpus)
+		return PSCI_RET_INVALID_PARAMS;
+
 	return PSCI_0_2_AFFINITY_LEVEL_OFF;
 }
 

arch/arm/mach-dove/irq.c

@@ -69,14 +69,14 @@ static struct irq_chip pmu_irq_chip = {
 	.irq_ack	= pmu_irq_ack,
 };
 
-static void pmu_irq_handler(unsigned int __irq, struct irq_desc *desc)
+static void pmu_irq_handler(struct irq_desc *desc)
 {
-	unsigned int irq = irq_desc_get_irq(desc);
 	unsigned long cause = readl(PMU_INTERRUPT_CAUSE);
+	unsigned int irq;
 
 	cause &= readl(PMU_INTERRUPT_MASK);
 	if (cause == 0) {
-		do_bad_IRQ(irq, desc);
+		do_bad_IRQ(desc);
 		return;
 	}
 

arch/arm/mach-footbridge/isa-irq.c

@@ -87,13 +87,12 @@ static struct irq_chip isa_hi_chip = {
 	.irq_unmask	= isa_unmask_pic_hi_irq,
 };
 
-static void
-isa_irq_handler(unsigned int irq, struct irq_desc *desc)
+static void isa_irq_handler(struct irq_desc *desc)
 {
 	unsigned int isa_irq = *(unsigned char *)PCIIACK_BASE;
 
 	if (isa_irq < _ISA_IRQ(0) || isa_irq >= _ISA_IRQ(16)) {
-		do_bad_IRQ(isa_irq, desc);
+		do_bad_IRQ(desc);
 		return;
 	}
 

arch/arm/mach-gemini/gpio.c

@@ -126,7 +126,7 @@ static int gpio_set_irq_type(struct irq_data *d, unsigned int type)
 	return 0;
 }
 
-static void gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
+static void gpio_irq_handler(struct irq_desc *desc)
 {
 	unsigned int port = (unsigned int)irq_desc_get_handler_data(desc);
 	unsigned int gpio_irq_no, irq_stat;

arch/arm/mach-imx/3ds_debugboard.c

@@ -85,7 +85,7 @@ static struct platform_device smsc_lan9217_device = {
 	.resource = smsc911x_resources,
 };
 
-static void mxc_expio_irq_handler(u32 irq, struct irq_desc *desc)
+static void mxc_expio_irq_handler(struct irq_desc *desc)
 {
 	u32 imr_val;
 	u32 int_valid;

arch/arm/mach-imx/mach-mx31ads.c

@@ -154,7 +154,7 @@ static inline void mxc_init_imx_uart(void)
 	imx31_add_imx_uart0(&uart_pdata);
 }
 
-static void mx31ads_expio_irq_handler(u32 irq, struct irq_desc *desc)
+static void mx31ads_expio_irq_handler(struct irq_desc *desc)
 {
 	u32 imr_val;
 	u32 int_valid;

arch/arm/mach-iop13xx/msi.c

@@ -91,7 +91,7 @@ static void (*write_imipr[])(u32) = {
 	write_imipr_3,
 };
 
-static void iop13xx_msi_handler(unsigned int irq, struct irq_desc *desc)
+static void iop13xx_msi_handler(struct irq_desc *desc)
 {
 	int i, j;
 	unsigned long status;

arch/arm/mach-lpc32xx/irq.c

@@ -370,7 +370,7 @@ static struct irq_chip lpc32xx_irq_chip = {
 	.irq_set_wake = lpc32xx_irq_wake
 };
 
-static void lpc32xx_sic1_handler(unsigned int irq, struct irq_desc *desc)
+static void lpc32xx_sic1_handler(struct irq_desc *desc)
 {
 	unsigned long ints = __raw_readl(LPC32XX_INTC_STAT(LPC32XX_SIC1_BASE));
 
@@ -383,7 +383,7 @@ static void lpc32xx_sic1_handler(unsigned int irq, struct irq_desc *desc)
 	}
 }
 
-static void lpc32xx_sic2_handler(unsigned int irq, struct irq_desc *desc)
+static void lpc32xx_sic2_handler(struct irq_desc *desc)
 {
 	unsigned long ints = __raw_readl(LPC32XX_INTC_STAT(LPC32XX_SIC2_BASE));
 

arch/arm/mach-netx/generic.c

@@ -69,8 +69,7 @@ static struct platform_device *devices[] __initdata = {
 #define DEBUG_IRQ(fmt...)	while (0) {}
 #endif
 
-static void
-netx_hif_demux_handler(unsigned int irq_unused, struct irq_desc *desc)
+static void netx_hif_demux_handler(struct irq_desc *desc)
 {
 	unsigned int irq = NETX_IRQ_HIF_CHAINED(0);
 	unsigned int stat;

arch/arm/mach-omap1/fpga.c

@@ -87,7 +87,7 @@ static void fpga_mask_ack_irq(struct irq_data *d)
 	fpga_ack_irq(d);
 }
 
-static void innovator_fpga_IRQ_demux(unsigned int irq, struct irq_desc *desc)
+static void innovator_fpga_IRQ_demux(struct irq_desc *desc)
 {
 	u32 stat;
 	int fpga_irq;

arch/arm/mach-omap2/Kconfig

@@ -44,10 +44,11 @@ config SOC_OMAP5
 	select ARM_CPU_SUSPEND if PM
 	select ARM_GIC
 	select HAVE_ARM_SCU if SMP
-	select HAVE_ARM_TWD if SMP
 	select HAVE_ARM_ARCH_TIMER
 	select ARM_ERRATA_798181 if SMP
+	select OMAP_INTERCONNECT
 	select OMAP_INTERCONNECT_BARRIER
+	select PM_OPP if PM
 
 config SOC_AM33XX
 	bool "TI AM33XX"
@@ -70,10 +71,13 @@ config SOC_DRA7XX
 	select ARCH_OMAP2PLUS
 	select ARM_CPU_SUSPEND if PM
 	select ARM_GIC
+	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_ARCH_TIMER
 	select IRQ_CROSSBAR
 	select ARM_ERRATA_798181 if SMP
+	select OMAP_INTERCONNECT
 	select OMAP_INTERCONNECT_BARRIER
+	select PM_OPP if PM
 
 config ARCH_OMAP2PLUS
 	bool

arch/arm/mach-omap2/board-generic.c

@@ -20,13 +20,6 @@
 
 #include "common.h"
 
-#if !(defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3))
-#define intc_of_init	NULL
-#endif
-#ifndef CONFIG_ARCH_OMAP4
-#define gic_of_init		NULL
-#endif
-
 static const struct of_device_id omap_dt_match_table[] __initconst = {
 	{ .compatible = "simple-bus", },
 	{ .compatible = "ti,omap-infra", },

arch/arm/mach-omap2/id.c

@@ -653,8 +653,12 @@ void __init dra7xxx_check_revision(void)
 			omap_revision = DRA752_REV_ES1_0;
 			break;
 		case 1:
-		default:
 			omap_revision = DRA752_REV_ES1_1;
+			break;
+		case 2:
+		default:
+			omap_revision = DRA752_REV_ES2_0;
+			break;
 		}
 		break;
 
@@ -674,7 +678,7 @@ void __init dra7xxx_check_revision(void)
 		/* Unknown default to latest silicon rev as default*/
 		pr_warn("%s: unknown idcode=0x%08x (hawkeye=0x%08x,rev=0x%x)\n",
 			__func__, idcode, hawkeye, rev);
-		omap_revision = DRA752_REV_ES1_1;
+		omap_revision = DRA752_REV_ES2_0;
 	}
 
 	sprintf(soc_name, "DRA%03x", omap_rev() >> 16);

arch/arm/mach-omap2/io.c

@@ -676,6 +676,7 @@ void __init am43xx_init_early(void)
 void __init am43xx_init_late(void)
 {
 	omap_common_late_init();
+	omap2_clk_enable_autoidle_all();
 }
 #endif
 

arch/arm/mach-omap2/omap_device.c

@@ -901,7 +901,8 @@ static int __init omap_device_late_idle(struct device *dev, void *data)
 		if (od->hwmods[i]->flags & HWMOD_INIT_NO_IDLE)
 			return 0;
 
-	if (od->_driver_status != BUS_NOTIFY_BOUND_DRIVER) {
+	if (od->_driver_status != BUS_NOTIFY_BOUND_DRIVER &&
+	    od->_driver_status != BUS_NOTIFY_BIND_DRIVER) {
 		if (od->_state == OMAP_DEVICE_STATE_ENABLED) {
 			dev_warn(dev, "%s: enabled but no driver.  Idling\n",
 				 __func__);

arch/arm/mach-omap2/pm.h

@@ -103,7 +103,8 @@ static inline void enable_omap3630_toggle_l2_on_restore(void) { }
 #define PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD	(1 << 0)
 #define PM_OMAP4_CPU_OSWR_DISABLE		(1 << 1)
 
-#if defined(CONFIG_PM) && defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_PM) && (defined(CONFIG_ARCH_OMAP4) ||\
+	   defined(CONFIG_SOC_OMAP5) || defined(CONFIG_SOC_DRA7XX))
 extern u16 pm44xx_errata;
 #define IS_PM44XX_ERRATUM(id)		(pm44xx_errata & (id))
 #else

arch/arm/mach-omap2/prm_common.c

@@ -102,7 +102,7 @@ static void omap_prcm_events_filter_priority(unsigned long *events,
  * dispatched accordingly. Clearing of the wakeup events should be
  * done by the SoC specific individual handlers.
  */
-static void omap_prcm_irq_handler(unsigned int irq, struct irq_desc *desc)
+static void omap_prcm_irq_handler(struct irq_desc *desc)
 {
 	unsigned long pending[OMAP_PRCM_MAX_NR_PENDING_REG];
 	unsigned long priority_pending[OMAP_PRCM_MAX_NR_PENDING_REG];

arch/arm/mach-omap2/soc.h

@@ -469,6 +469,8 @@ IS_OMAP_TYPE(3430, 0x3430)
 #define DRA7XX_CLASS		0x07000000
 #define DRA752_REV_ES1_0	(DRA7XX_CLASS | (0x52 << 16) | (0x10 << 8))
 #define DRA752_REV_ES1_1	(DRA7XX_CLASS | (0x52 << 16) | (0x11 << 8))
+#define DRA752_REV_ES2_0	(DRA7XX_CLASS | (0x52 << 16) | (0x20 << 8))
+#define DRA722_REV_ES1_0	(DRA7XX_CLASS | (0x22 << 16) | (0x10 << 8))
 #define DRA722_REV_ES1_0	(DRA7XX_CLASS | (0x22 << 16) | (0x10 << 8))
 
 void omap2xxx_check_revision(void);

arch/arm/mach-omap2/timer.c

@@ -297,12 +297,8 @@ static int __init omap_dm_timer_init_one(struct omap_dm_timer *timer,
 	if (IS_ERR(src))
 		return PTR_ERR(src);
 
-	r = clk_set_parent(timer->fclk, src);
-	if (r < 0) {
-		pr_warn("%s: %s cannot set source\n", __func__, oh->name);
-		clk_put(src);
-		return r;
-	}
+	WARN(clk_set_parent(timer->fclk, src) < 0,
+	     "Cannot set timer parent clock, no PLL clock driver?");
 
 	clk_put(src);
 

arch/arm/mach-omap2/vc.c

@@ -300,7 +300,7 @@ static void __init omap3_vc_init_pmic_signaling(struct voltagedomain *voltdm)
 
 	val = voltdm->read(OMAP3_PRM_POLCTRL_OFFSET);
 	if (!(val & OMAP3430_PRM_POLCTRL_CLKREQ_POL) ||
-	    (val & OMAP3430_PRM_POLCTRL_CLKREQ_POL)) {
+	    (val & OMAP3430_PRM_POLCTRL_OFFMODE_POL)) {
 		val |= OMAP3430_PRM_POLCTRL_CLKREQ_POL;
 		val &= ~OMAP3430_PRM_POLCTRL_OFFMODE_POL;
 		pr_debug("PM: fixing sys_clkreq and sys_off_mode polarity to 0x%x\n",

arch/arm/mach-pxa/balloon3.c

@@ -496,13 +496,13 @@ static struct irq_chip balloon3_irq_chip = {
 	.irq_unmask	= balloon3_unmask_irq,
 };
 
-static void balloon3_irq_handler(unsigned int __irq, struct irq_desc *desc)
+static void balloon3_irq_handler(struct irq_desc *desc)
 {
 	unsigned long pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
 					balloon3_irq_enabled;
 	do {
 		struct irq_data *d = irq_desc_get_irq_data(desc);
-		struct irq_chip *chip = irq_data_get_chip(d);
+		struct irq_chip *chip = irq_desc_get_chip(desc);
 		unsigned int irq;
 
 		/* clear useless edge notification */

arch/arm/mach-pxa/cm-x2xx-pci.c

@@ -29,13 +29,12 @@
 void __iomem *it8152_base_address;
 static int cmx2xx_it8152_irq_gpio;
 
-static void cmx2xx_it8152_irq_demux(unsigned int __irq, struct irq_desc *desc)
+static void cmx2xx_it8152_irq_demux(struct irq_desc *desc)
 {
-	unsigned int irq = irq_desc_get_irq(desc);
 	/* clear our parent irq */
 	desc->irq_data.chip->irq_ack(&desc->irq_data);
 
-	it8152_irq_demux(irq, desc);
+	it8152_irq_demux(desc);
 }
 
 void __cmx2xx_pci_init_irq(int irq_gpio)

arch/arm/mach-pxa/include/mach/addr-map.h

@@ -43,6 +43,13 @@
  * 0xf6200000..0xf6201000
  */
 
+/*
+ * DFI Bus for NAND, PXA3xx only
+ */
+#define NAND_PHYS		0x43100000
+#define NAND_VIRT		IOMEM(0xf6300000)
+#define NAND_SIZE		0x00100000
+
 /*
  * Internal Memory Controller (PXA27x and later)
  */

arch/arm/mach-pxa/lpd270.c

@@ -120,7 +120,7 @@ static struct irq_chip lpd270_irq_chip = {
 	.irq_unmask	= lpd270_unmask_irq,
 };
 
-static void lpd270_irq_handler(unsigned int __irq, struct irq_desc *desc)
+static void lpd270_irq_handler(struct irq_desc *desc)
 {
 	unsigned int irq;
 	unsigned long pending;

arch/arm/mach-pxa/pcm990-baseboard.c

@@ -284,7 +284,7 @@ static struct irq_chip pcm990_irq_chip = {
 	.irq_unmask	= pcm990_unmask_irq,
 };
 
-static void pcm990_irq_handler(unsigned int __irq, struct irq_desc *desc)
+static void pcm990_irq_handler(struct irq_desc *desc)
 {
 	unsigned int irq;
 	unsigned long pending;

arch/arm/mach-pxa/pxa3xx.c

@@ -47,6 +47,13 @@ extern void __init pxa_dt_irq_init(int (*fn)(struct irq_data *, unsigned int));
 #define ISRAM_START	0x5c000000
 #define ISRAM_SIZE	SZ_256K
 
+/*
+ * NAND NFC: DFI bus arbitration subset
+ */
+#define NDCR			(*(volatile u32 __iomem*)(NAND_VIRT + 0))
+#define NDCR_ND_ARB_EN		(1 << 12)
+#define NDCR_ND_ARB_CNTL	(1 << 19)
+
 static void __iomem *sram;
 static unsigned long wakeup_src;
 
@@ -362,7 +369,12 @@ static struct map_desc pxa3xx_io_desc[] __initdata = {
 		.pfn		= __phys_to_pfn(PXA3XX_SMEMC_BASE),
 		.length		= SMEMC_SIZE,
 		.type		= MT_DEVICE
-	}
+	}, {
+		.virtual	= (unsigned long)NAND_VIRT,
+		.pfn		= __phys_to_pfn(NAND_PHYS),
+		.length		= NAND_SIZE,
+		.type		= MT_DEVICE
+	},
 };
 
 void __init pxa3xx_map_io(void)
@@ -419,6 +431,13 @@ static int __init pxa3xx_init(void)
 		 */
 		ASCR &= ~(ASCR_RDH | ASCR_D1S | ASCR_D2S | ASCR_D3S);
 
+		/*
+		 * Disable DFI bus arbitration, to prevent a system bus lock if
+		 * somebody disables the NAND clock (unused clock) while this
+		 * bit remains set.
+		 */
+		NDCR = (NDCR & ~NDCR_ND_ARB_EN) | NDCR_ND_ARB_CNTL;
+
 		if ((ret = pxa_init_dma(IRQ_DMA, 32)))
 			return ret;
 

arch/arm/mach-pxa/viper.c

@@ -276,7 +276,7 @@ static inline unsigned long viper_irq_pending(void)
 			viper_irq_enabled_mask;
 }
 
-static void viper_irq_handler(unsigned int __irq, struct irq_desc *desc)
+static void viper_irq_handler(struct irq_desc *desc)
 {
 	unsigned int irq;
 	unsigned long pending;

arch/arm/mach-pxa/zeus.c

@@ -105,7 +105,7 @@ static inline unsigned long zeus_irq_pending(void)
 	return __raw_readw(ZEUS_CPLD_ISA_IRQ) & zeus_irq_enabled_mask;
 }
 
-static void zeus_irq_handler(unsigned int __irq, struct irq_desc *desc)
+static void zeus_irq_handler(struct irq_desc *desc)
 {
 	unsigned int irq;
 	unsigned long pending;

arch/arm/mach-rpc/ecard.c

@@ -551,8 +551,7 @@ static void ecard_check_lockup(struct irq_desc *desc)
 	}
 }
 
-static void
-ecard_irq_handler(unsigned int irq, struct irq_desc *desc)
+static void ecard_irq_handler(struct irq_desc *desc)
 {
 	ecard_t *ec;
 	int called = 0;

arch/arm/mach-s3c24xx/bast-irq.c

@@ -100,9 +100,7 @@ static struct irq_chip  bast_pc104_chip = {
 	.irq_ack	= bast_pc104_maskack
 };
 
-static void
-bast_irq_pc104_demux(unsigned int irq,
-		     struct irq_desc *desc)
+static void bast_irq_pc104_demux(struct irq_desc *desc)
 {
 	unsigned int stat;
 	unsigned int irqno;

arch/arm/mach-s3c64xx/common.c

@@ -388,22 +388,22 @@ static inline void s3c_irq_demux_eint(unsigned int start, unsigned int end)
 	}
 }
 
-static void s3c_irq_demux_eint0_3(unsigned int irq, struct irq_desc *desc)
+static void s3c_irq_demux_eint0_3(struct irq_desc *desc)
 {
 	s3c_irq_demux_eint(0, 3);
 }
 
-static void s3c_irq_demux_eint4_11(unsigned int irq, struct irq_desc *desc)
+static void s3c_irq_demux_eint4_11(struct irq_desc *desc)
 {
 	s3c_irq_demux_eint(4, 11);
 }
 
-static void s3c_irq_demux_eint12_19(unsigned int irq, struct irq_desc *desc)
+static void s3c_irq_demux_eint12_19(struct irq_desc *desc)
 {
 	s3c_irq_demux_eint(12, 19);
 }
 
-static void s3c_irq_demux_eint20_27(unsigned int irq, struct irq_desc *desc)
+static void s3c_irq_demux_eint20_27(struct irq_desc *desc)
 {
 	s3c_irq_demux_eint(20, 27);
 }

arch/arm/mach-sa1100/neponset.c

@@ -166,7 +166,7 @@ static struct sa1100_port_fns neponset_port_fns = {
  * ensure that the IRQ signal is deasserted before returning.  This
  * is rather unfortunate.
  */
-static void neponset_irq_handler(unsigned int irq, struct irq_desc *desc)
+static void neponset_irq_handler(struct irq_desc *desc)
 {
 	struct neponset_drvdata *d = irq_desc_get_handler_data(desc);
 	unsigned int irr;

arch/arm/mm/alignment.c

@@ -365,15 +365,21 @@ do_alignment_ldrhstrh(unsigned long addr, unsigned long instr, struct pt_regs *r
  user:
 	if (LDST_L_BIT(instr)) {
 		unsigned long val;
+		unsigned int __ua_flags = uaccess_save_and_enable();
+
 		get16t_unaligned_check(val, addr);
+		uaccess_restore(__ua_flags);
 
 		/* signed half-word? */
 		if (instr & 0x40)
 			val = (signed long)((signed short) val);
 
 		regs->uregs[rd] = val;
-	} else
+	} else {
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		put16t_unaligned_check(regs->uregs[rd], addr);
+		uaccess_restore(__ua_flags);
+	}
 
 	return TYPE_LDST;
 
@@ -420,14 +426,21 @@ do_alignment_ldrdstrd(unsigned long addr, unsigned long instr,
 
  user:
 	if (load) {
-		unsigned long val;
+		unsigned long val, val2;
+		unsigned int __ua_flags = uaccess_save_and_enable();
+
 		get32t_unaligned_check(val, addr);
+		get32t_unaligned_check(val2, addr + 4);
+
+		uaccess_restore(__ua_flags);
+
 		regs->uregs[rd] = val;
-		get32t_unaligned_check(val, addr + 4);
-		regs->uregs[rd2] = val;
+		regs->uregs[rd2] = val2;
 	} else {
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		put32t_unaligned_check(regs->uregs[rd], addr);
 		put32t_unaligned_check(regs->uregs[rd2], addr + 4);
+		uaccess_restore(__ua_flags);
 	}
 
 	return TYPE_LDST;
@@ -458,10 +471,15 @@ do_alignment_ldrstr(unsigned long addr, unsigned long instr, struct pt_regs *reg
  trans:
 	if (LDST_L_BIT(instr)) {
 		unsigned int val;
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		get32t_unaligned_check(val, addr);
+		uaccess_restore(__ua_flags);
 		regs->uregs[rd] = val;
-	} else
+	} else {
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		put32t_unaligned_check(regs->uregs[rd], addr);
+		uaccess_restore(__ua_flags);
+	}
 	return TYPE_LDST;
 
  fault:
@@ -531,6 +549,7 @@ do_alignment_ldmstm(unsigned long addr, unsigned long instr, struct pt_regs *reg
 #endif
 
 	if (user_mode(regs)) {
+		unsigned int __ua_flags = uaccess_save_and_enable();
 		for (regbits = REGMASK_BITS(instr), rd = 0; regbits;
 		     regbits >>= 1, rd += 1)
 			if (regbits & 1) {
@@ -542,6 +561,7 @@ do_alignment_ldmstm(unsigned long addr, unsigned long instr, struct pt_regs *reg
 					put32t_unaligned_check(regs->uregs[rd], eaddr);
 				eaddr += 4;
 			}
+		uaccess_restore(__ua_flags);
 	} else {
 		for (regbits = REGMASK_BITS(instr), rd = 0; regbits;
 		     regbits >>= 1, rd += 1)

arch/arm/mm/dma-mapping.c

@@ -1249,7 +1249,7 @@ __iommu_create_mapping(struct device *dev, struct page **pages, size_t size)
 	struct dma_iommu_mapping *mapping = to_dma_iommu_mapping(dev);
 	unsigned int count = PAGE_ALIGN(size) >> PAGE_SHIFT;
 	dma_addr_t dma_addr, iova;
-	int i, ret = DMA_ERROR_CODE;
+	int i;
 
 	dma_addr = __alloc_iova(mapping, size);
 	if (dma_addr == DMA_ERROR_CODE)
@@ -1257,6 +1257,8 @@ __iommu_create_mapping(struct device *dev, struct page **pages, size_t size)
 
 	iova = dma_addr;
 	for (i = 0; i < count; ) {
+		int ret;
+
 		unsigned int next_pfn = page_to_pfn(pages[i]) + 1;
 		phys_addr_t phys = page_to_phys(pages[i]);
 		unsigned int len, j;

arch/arm/plat-orion/gpio.c

@@ -407,7 +407,7 @@ static int gpio_irq_set_type(struct irq_data *d, u32 type)
 	return 0;
 }
 
-static void gpio_irq_handler(unsigned __irq, struct irq_desc *desc)
+static void gpio_irq_handler(struct irq_desc *desc)
 {
 	struct orion_gpio_chip *ochip = irq_desc_get_handler_data(desc);
 	u32 cause, type;

arch/arm/plat-pxa/ssp.c

@@ -107,7 +107,6 @@ static const struct of_device_id pxa_ssp_of_ids[] = {
 	{ .compatible = "mvrl,pxa168-ssp",	.data = (void *) PXA168_SSP },
 	{ .compatible = "mrvl,pxa910-ssp",	.data = (void *) PXA910_SSP },
 	{ .compatible = "mrvl,ce4100-ssp",	.data = (void *) CE4100_SSP },
-	{ .compatible = "mrvl,lpss-ssp",	.data = (void *) LPSS_SSP },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, pxa_ssp_of_ids);

arch/arm64/boot/dts/mediatek/mt8173.dtsi

@@ -81,7 +81,7 @@
 		};
 
 		idle-states {
-			entry-method = "arm,psci";
+			entry-method = "psci";
 
 			CPU_SLEEP_0: cpu-sleep-0 {
 				compatible = "arm,idle-state";

arch/arm64/boot/dts/rockchip/rk3368.dtsi

@@ -106,7 +106,7 @@
 		};
 
 		idle-states {
-			entry-method = "arm,psci";
+			entry-method = "psci";
 
 			cpu_sleep: cpu-sleep-0 {
 				compatible = "arm,idle-state";

arch/arm64/include/asm/hardirq.h

@@ -43,9 +43,4 @@ static inline void ack_bad_irq(unsigned int irq)
 	irq_err_count++;
 }
 
-/*
- * No arch-specific IRQ flags.
- */
-#define set_irq_flags(irq, flags)
-
 #endif /* __ASM_HARDIRQ_H */

arch/arm64/include/asm/kvm_arm.h

@@ -95,6 +95,7 @@
 			 SCTLR_EL2_SA | SCTLR_EL2_I)
 
 /* TCR_EL2 Registers bits */
+#define TCR_EL2_RES1	((1 << 31) | (1 << 23))
 #define TCR_EL2_TBI	(1 << 20)
 #define TCR_EL2_PS	(7 << 16)
 #define TCR_EL2_PS_40B	(2 << 16)
@@ -106,9 +107,10 @@
 #define TCR_EL2_MASK	(TCR_EL2_TG0 | TCR_EL2_SH0 | \
 			 TCR_EL2_ORGN0 | TCR_EL2_IRGN0 | TCR_EL2_T0SZ)
 
-#define TCR_EL2_FLAGS	(TCR_EL2_PS_40B)
+#define TCR_EL2_FLAGS	(TCR_EL2_RES1 | TCR_EL2_PS_40B)
 
 /* VTCR_EL2 Registers bits */
+#define VTCR_EL2_RES1		(1 << 31)
 #define VTCR_EL2_PS_MASK	(7 << 16)
 #define VTCR_EL2_TG0_MASK	(1 << 14)
 #define VTCR_EL2_TG0_4K		(0 << 14)
@@ -147,7 +149,8 @@
  */
 #define VTCR_EL2_FLAGS		(VTCR_EL2_TG0_64K | VTCR_EL2_SH0_INNER | \
 				 VTCR_EL2_ORGN0_WBWA | VTCR_EL2_IRGN0_WBWA | \
-				 VTCR_EL2_SL0_LVL1 | VTCR_EL2_T0SZ_40B)
+				 VTCR_EL2_SL0_LVL1 | VTCR_EL2_T0SZ_40B | \
+				 VTCR_EL2_RES1)
 #define VTTBR_X		(38 - VTCR_EL2_T0SZ_40B)
 #else
 /*
@@ -158,7 +161,8 @@
  */
 #define VTCR_EL2_FLAGS		(VTCR_EL2_TG0_4K | VTCR_EL2_SH0_INNER | \
 				 VTCR_EL2_ORGN0_WBWA | VTCR_EL2_IRGN0_WBWA | \
-				 VTCR_EL2_SL0_LVL1 | VTCR_EL2_T0SZ_40B)
+				 VTCR_EL2_SL0_LVL1 | VTCR_EL2_T0SZ_40B | \
+				 VTCR_EL2_RES1)
 #define VTTBR_X		(37 - VTCR_EL2_T0SZ_40B)
 #endif
 
@@ -168,7 +172,6 @@
 #define VTTBR_VMID_MASK	  (UL(0xFF) << VTTBR_VMID_SHIFT)
 
 /* Hyp System Trap Register */
-#define HSTR_EL2_TTEE	(1 << 16)
 #define HSTR_EL2_T(x)	(1 << x)
 
 /* Hyp Coproccessor Trap Register Shifts */