Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device tree changes from Arnd Bergmann:
 "A large part of the arm-soc patches are nowadays DT changes, adding
  support for new SoCs, boards and devices without changing kernel
  source.  The plan is still to move the devicetree files out of the
  kernel tree and reduce the amount of churn going on here, but we keep
  finding reasons to delay doing that.

  Changes are really all over the place, with little sticking out
  particularly.  We have contributions from a total of 116 people in
  this branch.

  Unfortunately, the size of this branch also causes a significant
  number of conflicts at the moment, typically when subsystem
  maintainers merge patches that change the driver at the same time as
  the dts files.  In most cases this could be avoided because the dts
  changes are supposed to be compatible in both ways, and we are asking
  everyone to send ARM dts changes through our tree only"

* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
  dts: stmmac: Document the clocks property in the stmmac base document
  dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
  ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
  ARM: STi: stih416: Add support for the FSM Serial Flash Controller
  ARM: tegra: fix Dalmore pinctrl configuration
  ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
  ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
  ARM: dts: Build all keystone dt blobs
  ARM: dts: keystone: Fix control register range for clktsip
  ARM: dts: keystone: Fix domain register range for clkfftc1
  ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
  ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
  ARM: dts: bcm21664: Add device tree files.
  ARM: DT: bcm21664: Device tree bindings
  ARM: efm32: properly namespace i2c location property
  ARM: efm32: fix unit address part in USART2 device nodes' names
  ARM: mvebu: Enable NAND controller in Armada 385-DB
  ARM: mvebu: Add support for NAND controller in Armada 38x SoC
  ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
  ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
  ...

Documentation/devicetree/bindings/arm/bcm/bcm21664.txt

@@ -0,0 +1,15 @@
+Broadcom BCM21664 device tree bindings
+--------------------------------------
+
+This document describes the device tree bindings for boards with the BCM21664
+SoC.
+
+Required root node property:
+  - compatible: brcm,bcm21664
+
+Example:
+	/ {
+		model = "BCM21664 SoC";
+		compatible = "brcm,bcm21664";
+		[...]
+	}

Documentation/devicetree/bindings/arm/bcm/kona-resetmgr.txt

@@ -0,0 +1,14 @@
+Broadcom Kona Family Reset Manager
+----------------------------------
+
+The reset manager is used on the Broadcom BCM21664 SoC.
+
+Required properties:
+  - compatible: brcm,bcm21664-resetmgr
+  - reg: memory address & range
+
+Example:
+	brcm,resetmgr@35001f00 {
+		compatible = "brcm,bcm21664-resetmgr";
+		reg = <0x35001f00 0x24>;
+	};

Documentation/devicetree/bindings/arm/keystone/keystone.txt

@@ -8,3 +8,13 @@ Required properties:
  - compatible: All TI specific devices present in Keystone SOC should be in
    the form "ti,keystone-*". Generic devices like gic, arch_timers, ns16550
    type UART should use the specified compatible for those devices.
+
+Boards:
+-  Keystone 2 Hawking/Kepler EVM
+   compatible = "ti,k2hk-evm","ti,keystone"
+
+-  Keystone 2 Lamarr EVM
+   compatible = "ti,k2l-evm","ti,keystone"
+
+-  Keystone 2 Edison EVM
+   compatible = "ti,k2e-evm","ti,keystone"

Documentation/devicetree/bindings/arm/omap/dmm.txt

@@ -0,0 +1,22 @@
+OMAP Dynamic Memory Manager (DMM) bindings
+
+The dynamic memory manager (DMM) is a module located immediately in front of the
+SDRAM controllers (called EMIFs on OMAP). DMM manages various aspects of memory
+accesses such as priority generation amongst initiators, configuration of SDRAM
+interleaving, optimizing transfer of 2D block objects, and provide MMU-like page
+translation for initiators which need contiguous dma bus addresses.
+
+Required properties:
+- compatible:	Should contain "ti,omap4-dmm" for OMAP4 family
+		Should contain "ti,omap5-dmm" for OMAP5 and DRA7x family
+- reg:		Contains DMM register address range (base address and length)
+- interrupts:	Should contain an interrupt-specifier for DMM_IRQ.
+- ti,hwmods:	Name of the hwmod associated to DMM, which is typically "dmm"
+
+Example:
+
+dmm@4e000000 {
+	compatible = "ti,omap4-dmm";
+	reg = <0x4e000000 0x800>;
+	ti,hwmods = "dmm";
+};

Documentation/devicetree/bindings/arm/omap/omap.txt

@@ -99,6 +99,9 @@ Boards:
 - OMAP4 PandaBoard : Low cost community board
   compatible = "ti,omap4-panda", "ti,omap4430"
 
+- OMAP4 DuoVero with Parlor : Commercial expansion board with daughter board
+  compatible = "gumstix,omap4-duovero-parlor", "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4";
+
 - OMAP3 EVM : Software Development Board for OMAP35x, AM/DM37x
   compatible = "ti,omap3-evm", "ti,omap3"
 
@@ -114,5 +117,8 @@ Boards:
 - AM43x EPOS EVM
   compatible = "ti,am43x-epos-evm", "ti,am4372", "ti,am43"
 
+- AM437x GP EVM
+  compatible = "ti,am437x-gp-evm", "ti,am4372", "ti,am43"
+
 - DRA7 EVM:  Software Developement Board for DRA7XX
   compatible = "ti,dra7-evm", "ti,dra7"

Documentation/devicetree/bindings/arm/samsung/pmu.txt

@@ -0,0 +1,15 @@
+SAMSUNG Exynos SoC series PMU Registers
+
+Properties:
+ - compatible : should contain two values. First value must be one from following list:
+		   - "samsung,exynos5250-pmu" - for Exynos5250 SoC,
+		   - "samsung,exynos5420-pmu" - for Exynos5420 SoC.
+		second value must be always "syscon".
+
+ - reg : offset and length of the register set.
+
+Example :
+pmu_system_controller: system-controller@10040000 {
+	compatible = "samsung,exynos5250-pmu", "syscon";
+	reg = <0x10040000 0x5000>;
+};

Documentation/devicetree/bindings/clock/exynos4-clock.txt

@@ -15,259 +15,12 @@ Required Properties:
 
 - #clock-cells: should be 1.
 
-The following is the list of clocks generated by the controller. Each clock is
-assigned an identifier and client nodes use this identifier to specify the
-clock which they consume. Some of the clocks are available only on a particular
-Exynos4 SoC and this is specified where applicable.
-
-
-		 [Core Clocks]
-
-  Clock               ID      SoC (if specific)
-  -----------------------------------------------
-
-  xxti                1
-  xusbxti             2
-  fin_pll             3
-  fout_apll           4
-  fout_mpll           5
-  fout_epll           6
-  fout_vpll           7
-  sclk_apll           8
-  sclk_mpll           9
-  sclk_epll           10
-  sclk_vpll           11
-  arm_clk             12
-  aclk200             13
-  aclk100             14
-  aclk160             15
-  aclk133             16
-  mout_mpll_user_t    17      Exynos4x12
-  mout_mpll_user_c    18      Exynos4x12
-  mout_core           19
-  mout_apll           20
-
-
-            [Clock Gate for Special Clocks]
-
-  Clock               ID      SoC (if specific)
-  -----------------------------------------------
-
-  sclk_fimc0          128
-  sclk_fimc1          129
-  sclk_fimc2          130
-  sclk_fimc3          131
-  sclk_cam0           132
-  sclk_cam1           133
-  sclk_csis0          134
-  sclk_csis1          135
-  sclk_hdmi           136
-  sclk_mixer          137
-  sclk_dac            138
-  sclk_pixel          139
-  sclk_fimd0          140
-  sclk_mdnie0         141     Exynos4412
-  sclk_mdnie_pwm0 12  142     Exynos4412
-  sclk_mipi0          143
-  sclk_audio0         144
-  sclk_mmc0           145
-  sclk_mmc1           146
-  sclk_mmc2           147
-  sclk_mmc3           148
-  sclk_mmc4           149
-  sclk_sata           150     Exynos4210
-  sclk_uart0          151
-  sclk_uart1          152
-  sclk_uart2          153
-  sclk_uart3          154
-  sclk_uart4          155
-  sclk_audio1         156
-  sclk_audio2         157
-  sclk_spdif          158
-  sclk_spi0           159
-  sclk_spi1           160
-  sclk_spi2           161
-  sclk_slimbus        162
-  sclk_fimd1          163     Exynos4210
-  sclk_mipi1          164     Exynos4210
-  sclk_pcm1           165
-  sclk_pcm2           166
-  sclk_i2s1           167
-  sclk_i2s2           168
-  sclk_mipihsi        169     Exynos4412
-  sclk_mfc            170
-  sclk_pcm0           171
-  sclk_g3d            172
-  sclk_pwm_isp        173     Exynos4x12
-  sclk_spi0_isp       174     Exynos4x12
-  sclk_spi1_isp       175     Exynos4x12
-  sclk_uart_isp       176     Exynos4x12
-  sclk_fimg2d         177
-
-	      [Peripheral Clock Gates]
-
-  Clock               ID      SoC (if specific)
-  -----------------------------------------------
-
-  fimc0               256
-  fimc1               257
-  fimc2               258
-  fimc3               259
-  csis0               260
-  csis1               261
-  jpeg                262
-  smmu_fimc0          263
-  smmu_fimc1          264
-  smmu_fimc2          265
-  smmu_fimc3          266
-  smmu_jpeg           267
-  vp                  268
-  mixer               269
-  tvenc               270     Exynos4210
-  hdmi                271
-  smmu_tv             272
-  mfc                 273
-  smmu_mfcl           274
-  smmu_mfcr           275
-  g3d                 276
-  g2d                 277
-  rotator             278     Exynos4210
-  mdma                279     Exynos4210
-  smmu_g2d            280     Exynos4210
-  smmu_rotator        281     Exynos4210
-  smmu_mdma           282     Exynos4210
-  fimd0               283
-  mie0                284
-  mdnie0              285     Exynos4412
-  dsim0               286
-  smmu_fimd0          287
-  fimd1               288     Exynos4210
-  mie1                289     Exynos4210
-  dsim1               290     Exynos4210
-  smmu_fimd1          291     Exynos4210
-  pdma0               292
-  pdma1               293
-  pcie_phy            294
-  sata_phy            295     Exynos4210
-  tsi                 296
-  sdmmc0              297
-  sdmmc1              298
-  sdmmc2              299
-  sdmmc3              300
-  sdmmc4              301
-  sata                302     Exynos4210
-  sromc               303
-  usb_host            304
-  usb_device          305
-  pcie                306
-  onenand             307
-  nfcon               308
-  smmu_pcie           309
-  gps                 310
-  smmu_gps            311
-  uart0               312
-  uart1               313
-  uart2               314
-  uart3               315
-  uart4               316
-  i2c0                317
-  i2c1                318
-  i2c2                319
-  i2c3                320
-  i2c4                321
-  i2c5                322
-  i2c6                323
-  i2c7                324
-  i2c_hdmi            325
-  tsadc               326
-  spi0                327
-  spi1                328
-  spi2                329
-  i2s1                330
-  i2s2                331
-  pcm0                332
-  i2s0                333
-  pcm1                334
-  pcm2                335
-  pwm                 336
-  slimbus             337
-  spdif               338
-  ac97                339
-  modemif             340
-  chipid              341
-  sysreg              342
-  hdmi_cec            343
-  mct                 344
-  wdt                 345
-  rtc                 346
-  keyif               347
-  audss               348
-  mipi_hsi            349     Exynos4210
-  mdma2               350     Exynos4210
-  pixelasyncm0        351
-  pixelasyncm1        352
-  fimc_lite0          353     Exynos4x12
-  fimc_lite1          354     Exynos4x12
-  ppmuispx            355     Exynos4x12
-  ppmuispmx           356     Exynos4x12
-  fimc_isp            357     Exynos4x12
-  fimc_drc            358     Exynos4x12
-  fimc_fd             359     Exynos4x12
-  mcuisp              360     Exynos4x12
-  gicisp              361     Exynos4x12
-  smmu_isp            362     Exynos4x12
-  smmu_drc            363     Exynos4x12
-  smmu_fd             364     Exynos4x12
-  smmu_lite0          365     Exynos4x12
-  smmu_lite1          366     Exynos4x12
-  mcuctl_isp          367     Exynos4x12
-  mpwm_isp            368     Exynos4x12
-  i2c0_isp            369     Exynos4x12
-  i2c1_isp            370     Exynos4x12
-  mtcadc_isp          371     Exynos4x12
-  pwm_isp             372     Exynos4x12
-  wdt_isp             373     Exynos4x12
-  uart_isp            374     Exynos4x12
-  asyncaxim           375     Exynos4x12
-  smmu_ispcx          376     Exynos4x12
-  spi0_isp            377     Exynos4x12
-  spi1_isp            378     Exynos4x12
-  pwm_isp_sclk        379     Exynos4x12
-  spi0_isp_sclk       380     Exynos4x12
-  spi1_isp_sclk       381     Exynos4x12
-  uart_isp_sclk       382     Exynos4x12
-  tmu_apbif           383
-
-		[Mux Clocks]
-
-  Clock			ID	SoC (if specific)
-  -----------------------------------------------
-
-  mout_fimc0		384
-  mout_fimc1		385
-  mout_fimc2		386
-  mout_fimc3		387
-  mout_cam0		388
-  mout_cam1		389
-  mout_csis0		390
-  mout_csis1		391
-  mout_g3d0		392
-  mout_g3d1		393
-  mout_g3d		394
-  aclk400_mcuisp	395	Exynos4x12
-
-		[Div Clocks]
-
-  Clock			ID	SoC (if specific)
-  -----------------------------------------------
-
-  div_isp0		450	Exynos4x12
-  div_isp1		451	Exynos4x12
-  div_mcuisp0		452	Exynos4x12
-  div_mcuisp1		453	Exynos4x12
-  div_aclk200		454	Exynos4x12
-  div_aclk400_mcuisp	455	Exynos4x12
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume.
 
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/exynos4.h header and can be used in device
+tree sources.
 
 Example 1: An example of a clock controller node is listed below.
 
@@ -285,6 +38,6 @@ Example 2: UART controller node that consumes the clock generated by the clock
 		compatible = "samsung,exynos4210-uart";
 		reg = <0x13820000 0x100>;
 		interrupts = <0 54 0>;
-		clocks = <&clock 314>, <&clock 153>;
+		clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
 		clock-names = "uart", "clk_uart_baud0";
 	};

Documentation/devicetree/bindings/clock/exynos5250-clock.txt

@@ -13,163 +13,12 @@ Required Properties:
 
 - #clock-cells: should be 1.
 
-The following is the list of clocks generated by the controller. Each clock is
-assigned an identifier and client nodes use this identifier to specify the
-clock which they consume.
-
-
-       [Core Clocks]
-
-  Clock			ID
-  ----------------------------
-
-  fin_pll		1
-
-  [Clock Gate for Special Clocks]
-
-  Clock			ID
-  ----------------------------
-
-  sclk_cam_bayer	128
-  sclk_cam0		129
-  sclk_cam1		130
-  sclk_gscl_wa		131
-  sclk_gscl_wb		132
-  sclk_fimd1		133
-  sclk_mipi1		134
-  sclk_dp		135
-  sclk_hdmi		136
-  sclk_pixel		137
-  sclk_audio0		138
-  sclk_mmc0		139
-  sclk_mmc1		140
-  sclk_mmc2		141
-  sclk_mmc3		142
-  sclk_sata		143
-  sclk_usb3		144
-  sclk_jpeg		145
-  sclk_uart0		146
-  sclk_uart1		147
-  sclk_uart2		148
-  sclk_uart3		149
-  sclk_pwm		150
-  sclk_audio1		151
-  sclk_audio2		152
-  sclk_spdif		153
-  sclk_spi0		154
-  sclk_spi1		155
-  sclk_spi2		156
-  div_i2s1		157
-  div_i2s2		158
-  sclk_hdmiphy		159
-  div_pcm0		160
-
-
-   [Peripheral Clock Gates]
-
-  Clock			ID
-  ----------------------------
-
-  gscl0			256
-  gscl1			257
-  gscl2			258
-  gscl3			259
-  gscl_wa		260
-  gscl_wb		261
-  smmu_gscl0		262
-  smmu_gscl1		263
-  smmu_gscl2		264
-  smmu_gscl3		265
-  mfc			266
-  smmu_mfcl		267
-  smmu_mfcr		268
-  rotator		269
-  jpeg			270
-  mdma1			271
-  smmu_rotator		272
-  smmu_jpeg		273
-  smmu_mdma1		274
-  pdma0			275
-  pdma1			276
-  sata			277
-  usbotg		278
-  mipi_hsi		279
-  sdmmc0		280
-  sdmmc1		281
-  sdmmc2		282
-  sdmmc3		283
-  sromc			284
-  usb2			285
-  usb3			286
-  sata_phyctrl		287
-  sata_phyi2c		288
-  uart0			289
-  uart1			290
-  uart2			291
-  uart3			292
-  uart4			293
-  i2c0			294
-  i2c1			295
-  i2c2			296
-  i2c3			297
-  i2c4			298
-  i2c5			299
-  i2c6			300
-  i2c7			301
-  i2c_hdmi		302
-  adc			303
-  spi0			304
-  spi1			305
-  spi2			306
-  i2s1			307
-  i2s2			308
-  pcm1			309
-  pcm2			310
-  pwm			311
-  spdif			312
-  ac97			313
-  hsi2c0		314
-  hsi2c1		315
-  hs12c2		316
-  hs12c3		317
-  chipid		318
-  sysreg		319
-  pmu			320
-  cmu_top		321
-  cmu_core		322
-  cmu_mem		323
-  tzpc0			324
-  tzpc1			325
-  tzpc2			326
-  tzpc3			327
-  tzpc4			328
-  tzpc5			329
-  tzpc6			330
-  tzpc7			331
-  tzpc8			332
-  tzpc9			333
-  hdmi_cec		334
-  mct			335
-  wdt			336
-  rtc			337
-  tmu			338
-  fimd1			339
-  mie1			340
-  dsim0			341
-  dp			342
-  mixer			343
-  hdmi			344
-  g2d			345
-  mdma0			346
-  smmu_mdma0		347
-
-
-   [Clock Muxes]
-
-  Clock			ID
-  ----------------------------
-  mout_hdmi		1024
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume.
 
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/exynos5250.h header and can be used in device
+tree sources.
 
 Example 1: An example of a clock controller node is listed below.
 
@@ -187,6 +36,6 @@ Example 2: UART controller node that consumes the clock generated by the clock
 		compatible = "samsung,exynos4210-uart";
 		reg = <0x13820000 0x100>;
 		interrupts = <0 54 0>;
-		clocks = <&clock 314>, <&clock 153>;
+		clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
 		clock-names = "uart", "clk_uart_baud0";
 	};

Documentation/devicetree/bindings/clock/exynos5420-clock.txt

@@ -13,184 +13,12 @@ Required Properties:
 
 - #clock-cells: should be 1.
 
-The following is the list of clocks generated by the controller. Each clock is
-assigned an identifier and client nodes use this identifier to specify the
-clock which they consume.
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume.
 
-
-       [Core Clocks]
-
-  Clock			ID
-  ----------------------------
-
-  fin_pll		1
-
-  [Clock Gate for Special Clocks]
-
-  Clock			ID
-  ----------------------------
-  sclk_uart0		128
-  sclk_uart1		129
-  sclk_uart2		130
-  sclk_uart3		131
-  sclk_mmc0		132
-  sclk_mmc1		133
-  sclk_mmc2		134
-  sclk_spi0		135
-  sclk_spi1		136
-  sclk_spi2		137
-  sclk_i2s1		138
-  sclk_i2s2		139
-  sclk_pcm1		140
-  sclk_pcm2		141
-  sclk_spdif		142
-  sclk_hdmi		143
-  sclk_pixel		144
-  sclk_dp1		145
-  sclk_mipi1		146
-  sclk_fimd1		147
-  sclk_maudio0		148
-  sclk_maupcm0		149
-  sclk_usbd300		150
-  sclk_usbd301		151
-  sclk_usbphy300	152
-  sclk_usbphy301	153
-  sclk_unipro		154
-  sclk_pwm		155
-  sclk_gscl_wa		156
-  sclk_gscl_wb		157
-  sclk_hdmiphy		158
-
-   [Peripheral Clock Gates]
-
-  Clock			ID
-  ----------------------------
-
-  aclk66_peric		256
-  uart0			257
-  uart1			258
-  uart2			259
-  uart3			260
-  i2c0			261
-  i2c1			262
-  i2c2			263
-  i2c3			264
-  i2c4			265
-  i2c5			266
-  i2c6			267
-  i2c7			268
-  i2c_hdmi		269
-  tsadc			270
-  spi0			271
-  spi1			272
-  spi2			273
-  keyif			274
-  i2s1			275
-  i2s2			276
-  pcm1			277
-  pcm2			278
-  pwm			279
-  spdif			280
-  i2c8			281
-  i2c9			282
-  i2c10			283
-  aclk66_psgen		300
-  chipid		301
-  sysreg		302
-  tzpc0			303
-  tzpc1			304
-  tzpc2			305
-  tzpc3			306
-  tzpc4			307
-  tzpc5			308
-  tzpc6			309
-  tzpc7			310
-  tzpc8			311
-  tzpc9			312
-  hdmi_cec		313
-  seckey		314
-  mct			315
-  wdt			316
-  rtc			317
-  tmu			318
-  tmu_gpu		319
-  pclk66_gpio		330
-  aclk200_fsys2		350
-  mmc0			351
-  mmc1			352
-  mmc2			353
-  sromc			354
-  ufs			355
-  aclk200_fsys		360
-  tsi			361
-  pdma0			362
-  pdma1			363
-  rtic			364
-  usbh20		365
-  usbd300		366
-  usbd301		377
-  aclk400_mscl		380
-  mscl0			381
-  mscl1			382
-  mscl2			383
-  smmu_mscl0		384
-  smmu_mscl1		385
-  smmu_mscl2		386
-  aclk333		400
-  mfc			401
-  smmu_mfcl		402
-  smmu_mfcr		403
-  aclk200_disp1		410
-  dsim1			411
-  dp1			412
-  hdmi			413
-  aclk300_disp1		420
-  fimd1			421
-  smmu_fimd1		422
-  aclk166		430
-  mixer			431
-  aclk266		440
-  rotator		441
-  mdma1			442
-  smmu_rotator		443
-  smmu_mdma1		444
-  aclk300_jpeg		450
-  jpeg			451
-  jpeg2			452
-  smmu_jpeg		453
-  aclk300_gscl		460
-  smmu_gscl0		461
-  smmu_gscl1		462
-  gscl_wa		463
-  gscl_wb		464
-  gscl0			465
-  gscl1			466
-  clk_3aa		467
-  aclk266_g2d		470
-  sss			471
-  slim_sss		472
-  mdma0			473
-  aclk333_g2d		480
-  g2d			481
-  aclk333_432_gscl	490
-  smmu_3aa		491
-  smmu_fimcl0		492
-  smmu_fimcl1		493
-  smmu_fimcl3		494
-  fimc_lite3		495
-  aclk_g3d		500
-  g3d			501
-  smmu_mixer		502
-
-  Mux			ID
-  ----------------------------
-
-  mout_hdmi		640
-
-  Divider		ID
-  ----------------------------
-
-  dout_pixel		768
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/exynos5420.h header and can be used in device
+tree sources.
 
 Example 1: An example of a clock controller node is listed below.
 
@@ -208,6 +36,6 @@ Example 2: UART controller node that consumes the clock generated by the clock
 		compatible = "samsung,exynos4210-uart";
 		reg = <0x13820000 0x100>;
 		interrupts = <0 54 0>;
-		clocks = <&clock 259>, <&clock 130>;
+		clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
 		clock-names = "uart", "clk_uart_baud0";
 	};

Documentation/devicetree/bindings/clock/exynos5440-clock.txt

@@ -12,45 +12,12 @@ Required Properties:
 
 - #clock-cells: should be 1.
 
-The following is the list of clocks generated by the controller. Each clock is
-assigned an identifier and client nodes use this identifier to specify the
-clock which they consume.
-
-
-       [Core Clocks]
-
-  Clock			ID
-  ----------------------------
-
-  xtal			1
-  arm_clk		2
-
-   [Peripheral Clock Gates]
-
-  Clock			ID
-  ----------------------------
-
-  spi_baud		16
-  pb0_250		17
-  pr0_250		18
-  pr1_250		19
-  b_250			20
-  b_125			21
-  b_200			22
-  sata			23
-  usb			24
-  gmac0			25
-  cs250			26
-  pb0_250_o		27
-  pr0_250_o		28
-  pr1_250_o		29
-  b_250_o		30
-  b_125_o		31
-  b_200_o		32
-  sata_o		33
-  usb_o			34
-  gmac0_o		35
-  cs250_o		36
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume.
+
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/exynos5440.h header and can be used in device
+tree sources.
 
 Example: An example of a clock controller node is listed below.
 

Documentation/devicetree/bindings/i2c/trivial-devices.txt

@@ -59,6 +59,7 @@ plx,pex8648		48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch
 ramtron,24c64		i2c serial eeprom  (24cxx)
 ricoh,rs5c372a		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
 samsung,24ad0xd1	S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power)
+sii,s35390a		2-wire CMOS real-time clock
 st-micro,24c256		i2c serial eeprom  (24cxx)
 stm,m41t00		Serial Access TIMEKEEPER
 stm,m41t62		Serial real-time clock (RTC) with alarm

Documentation/devicetree/bindings/arm/atmel-adc.txt → Documentation/devicetree/bindings/iio/adc/at91_adc.txt

@@ -8,32 +8,32 @@ Required properties:
   - clock-names: tuple listing input clock names.
 	Required elements: "adc_clk", "adc_op_clk".
   - clocks: phandles to input clocks.
-  - atmel,adc-channels-used: Bitmask of the channels muxed and enable for this
+  - atmel,adc-channels-used: Bitmask of the channels muxed and enabled for this
     device
   - atmel,adc-startup-time: Startup Time of the ADC in microseconds as
     defined in the datasheet
   - atmel,adc-vref: Reference voltage in millivolts for the conversions
-  - atmel,adc-res: List of resolution in bits supported by the ADC. List size
+  - atmel,adc-res: List of resolutions in bits supported by the ADC. List size
 		   must be two at least.
   - atmel,adc-res-names: Contains one identifier string for each resolution
 			 in atmel,adc-res property. "lowres" and "highres"
 			 identifiers are required.
 
 Optional properties:
-  - atmel,adc-use-external: Boolean to enable of external triggers
+  - atmel,adc-use-external-triggers: Boolean to enable the external triggers
   - atmel,adc-use-res: String corresponding to an identifier from
 		       atmel,adc-res-names property. If not specified, the highest
 		       resolution will be used.
   - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion
   - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds
-  - atmel,adc-ts-wires: Number of touch screen wires. Should be 4 or 5. If this
-                        value is set, then adc driver will enable touch screen
+  - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this
+                        value is set, then the adc driver will enable touchscreen
                         support.
-    NOTE: when adc touch screen enabled, the adc hardware trigger will be
-          disabled. Since touch screen will occupied the trigger register.
+    NOTE: when adc touchscreen is enabled, the adc hardware trigger will be
+          disabled. Since touchscreen will occupy the trigger register.
   - atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It
-                                     make touch detect more precision.
- 
+                                     makes touch detection more precise.
+
 Optional trigger Nodes:
   - Required properties:
     * trigger-name: Name of the trigger exposed to the user
@@ -44,42 +44,43 @@ Optional trigger Nodes:
 
 Examples:
 adc0: adc@fffb0000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	compatible = "atmel,at91sam9260-adc";
 	reg = <0xfffb0000 0x100>;
-	interrupts = <20 4>;
+	interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
 	clocks = <&adc_clk>, <&adc_op_clk>;
 	clock-names = "adc_clk", "adc_op_clk";
-	atmel,adc-channel-base = <0x30>;
 	atmel,adc-channels-used = <0xff>;
-	atmel,adc-drdy-mask = <0x10000>;
-	atmel,adc-num-channels = <8>;
 	atmel,adc-startup-time = <40>;
-	atmel,adc-status-register = <0x1c>;
-	atmel,adc-trigger-register = <0x08>;
-	atmel,adc-use-external;
+	atmel,adc-use-external-triggers;
 	atmel,adc-vref = <3300>;
 	atmel,adc-res = <8 10>;
 	atmel,adc-res-names = "lowres", "highres";
 	atmel,adc-use-res = "lowres";
 
 	trigger@0 {
+		reg = <0>;
 		trigger-name = "external-rising";
 		trigger-value = <0x1>;
 		trigger-external;
 	};
 	trigger@1 {
+		reg = <1>;
 		trigger-name = "external-falling";
 		trigger-value = <0x2>;
 		trigger-external;
 	};
 
 	trigger@2 {
+		reg = <2>;
 		trigger-name = "external-any";
 		trigger-value = <0x3>;
 		trigger-external;
 	};
 
 	trigger@3 {
+		reg = <3>;
 		trigger-name = "continuous";
 		trigger-value = <0x6>;
 	};

Documentation/devicetree/bindings/net/socfpga-dwmac.txt

@@ -0,0 +1,27 @@
+Altera SOCFPGA SoC DWMAC controller
+
+This is a variant of the dwmac/stmmac driver an inherits all descriptions
+present in Documentation/devicetree/bindings/net/stmmac.txt.
+
+The device node has additional properties:
+
+Required properties:
+ - compatible	: Should contain "altr,socfpga-stmmac" along with
+		  "snps,dwmac" and any applicable more detailed
+		  designware version numbers documented in stmmac.txt
+ - altr,sysmgr-syscon : Should be the phandle to the system manager node that
+   encompasses the glue register, the register offset, and the register shift.
+
+Example:
+
+gmac0: ethernet@ff700000 {
+	compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac";
+	altr,sysmgr-syscon = <&sysmgr 0x60 0>;
+	status = "disabled";
+	reg = <0xff700000 0x2000>;
+	interrupts = <0 115 4>;
+	interrupt-names = "macirq";
+	mac-address = [00 00 00 00 00 00];/* Filled in by U-Boot */
+	clocks = <&emac_0_clk>;
+	clocks-names = "stmmaceth";
+};

Documentation/devicetree/bindings/net/stmmac.txt

@@ -31,6 +31,10 @@ Optional properties:
 - reset-names: Should contain the reset signal name "stmmaceth", if a
 	reset phandle is given
 - max-frame-size: See ethernet.txt file in the same directory
+- clocks: If present, the first clock should be the GMAC main clock,
+  further clocks may be specified in derived bindings.
+- clocks-names: One name for each entry in the clocks property, the
+  first one should be "stmmaceth".
 
 Examples:
 
@@ -43,4 +47,6 @@ Examples:
 		mac-address = [000000000000]; /* Filled in by U-Boot */
 		max-frame-size = <3800>;
 		phy-mode = "gmii";
+		clocks = <&clock>;
+		clock-names = "stmmaceth">;
 	};

Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt

@@ -42,6 +42,10 @@ Required properties:
     - 0xc2000000: prefetchable memory region
   Please refer to the standard PCI bus binding document for a more detailed
   explanation.
+- #interrupt-cells: Size representation for interrupts (must be 1)
+- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
+  Please refer to the standard PCI bus binding document for a more detailed
+  explanation.
 - clocks: Must contain an entry for each entry in clock-names.
   See ../clocks/clock-bindings.txt for details.
 - clock-names: Must include the following entries:
@@ -86,6 +90,10 @@ SoC DTSI:
 		              0 99 0x04>; /* MSI interrupt */
 		interrupt-names = "intr", "msi";
 
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+
 		bus-range = <0x00 0xff>;
 		#address-cells = <3>;
 		#size-cells = <2>;

Documentation/devicetree/bindings/reset/st,sti-powerdown.txt

@@ -0,0 +1,47 @@
+STMicroelectronics STi family Sysconfig Peripheral Powerdown Reset Controller
+=============================================================================
+
+This binding describes a reset controller device that is used to enable and
+disable on-chip peripheral controllers such as USB and SATA, using
+"powerdown" control bits found in the STi family SoC system configuration
+registers. These have been grouped together into a single reset controller
+device for convenience.
+
+The actual action taken when powerdown is asserted is hardware dependent.
+However, when asserted it may not be possible to access the hardware's
+registers and after an assert/deassert sequence the hardware's previous state
+may no longer be valid.
+
+Please refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "st,<chip>-powerdown"
+	ex: "st,stih415-powerdown", "st,stih416-powerdown"
+- #reset-cells: 1, see below
+
+example:
+
+	powerdown: powerdown-controller {
+		#reset-cells = <1>;
+		compatible = "st,stih415-powerdown";
+	};
+
+
+Specifying powerdown control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the powerdown device node and an
+index specifying which channel to use, as described in reset.txt
+
+example:
+
+	usb1: usb@fe200000 {
+		resets	= <&powerdown STIH41X_USB1_POWERDOWN>;
+	};
+
+Macro definitions for the supported reset channels can be found in:
+
+include/dt-bindings/reset-controller/stih415-resets.h
+include/dt-bindings/reset-controller/stih416-resets.h

Documentation/devicetree/bindings/reset/st,sti-softreset.txt

@@ -0,0 +1,46 @@
+STMicroelectronics STi family Sysconfig Peripheral SoftReset Controller
+=============================================================================
+
+This binding describes a reset controller device that is used to enable and
+disable on-chip peripheral controllers such as USB and SATA, using
+"softreset" control bits found in the STi family SoC system configuration
+registers.
+
+The actual action taken when softreset is asserted is hardware dependent.
+However, when asserted it may not be possible to access the hardware's
+registers and after an assert/deassert sequence the hardware's previous state
+may no longer be valid.
+
+Please refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "st,<chip>-softreset" example:
+	"st,stih415-softreset" or "st,stih416-softreset";
+- #reset-cells: 1, see below
+
+example:
+
+	softreset: softreset-controller {
+		#reset-cells = <1>;
+		compatible = "st,stih415-softreset";
+	};
+
+
+Specifying softreset control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the softreset device node and an
+index specifying which channel to use, as described in reset.txt
+
+example:
+
+	ethernet0{
+		resets			= <&softreset STIH415_ETH0_SOFTRESET>;
+	};
+
+Macro definitions for the supported reset channels can be found in:
+
+include/dt-bindings/reset-controller/stih415-resets.h
+include/dt-bindings/reset-controller/stih416-resets.h

Documentation/devicetree/bindings/usb/atmel-usb.txt

@@ -57,8 +57,8 @@ Required properties:
  - ep childnode: To specify the number of endpoints and their properties.
 
 Optional properties:
- - atmel,vbus-gpio: If present, specifies a gpio that needs to be
-   activated for the bus to be powered.
+ - atmel,vbus-gpio: If present, specifies a gpio that allows to detect whether
+   vbus is present (USB is connected).
 
 Required child node properties:
  - name: Name of the endpoint.

Documentation/devicetree/bindings/usb/ehci-omap.txt

@@ -21,7 +21,7 @@ Documentation/devicetree/bindings/mfd/omap-usb-host.txt
 Example for OMAP4:
 
 usbhsehci: ehci@4a064c00 {
-	compatible = "ti,ehci-omap", "usb-ehci";
+	compatible = "ti,ehci-omap";
 	reg = <0x4a064c00 0x400>;
 	interrupts = <0 77 0x4>;
 };

Documentation/devicetree/bindings/usb/ohci-omap3.txt

@@ -9,7 +9,7 @@ Required properties:
 Example for OMAP4:
 
 usbhsohci: ohci@4a064800 {
-	compatible = "ti,ohci-omap3", "usb-ohci";
+	compatible = "ti,ohci-omap3";
 	reg = <0x4a064800 0x400>;
 	interrupts = <0 76 0x4>;
 };

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -35,11 +35,13 @@ dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
 davicom	DAVICOM Semiconductor, Inc.
 dlink	D-Link Systems, Inc.
 denx	Denx Software Engineering
+dmo	Data Modul AG
 edt	Emerging Display Technologies
 emmicro	EM Microelectronic
 epfl	Ecole Polytechnique Fédérale de Lausanne
 epson	Seiko Epson Corp.
 est	ESTeem Wireless Modems
+eukrea  Eukréa Electromatique
 fsl	Freescale Semiconductor
 GEFanuc	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
 gef	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
@@ -83,10 +85,12 @@ picochip	Picochip Ltd
 powervr	PowerVR (deprecated, use img)
 qca	Qualcomm Atheros, Inc.
 qcom	Qualcomm Technologies, Inc
+qnap	QNAP Systems, Inc.
 ralink	Mediatek/Ralink Technology Corp.
 ramtron	Ramtron International
 realtek Realtek Semiconductor Corp.
 renesas	Renesas Electronics Corporation
+ricoh	Ricoh Co. Ltd.
 rockchip	Fuzhou Rockchip Electronics Co., Ltd
 samsung	Samsung Semiconductor
 sbs	Smart Battery System
@@ -94,6 +98,7 @@ schindler	Schindler
 sil	Silicon Image
 silabs	Silicon Laboratories
 simtek
+sii	Seiko Instruments, Inc.
 sirf	SiRF Technology, Inc.
 smsc	Standard Microsystems Corporation
 snps 	Synopsys, Inc.
@@ -101,12 +106,14 @@ spansion	Spansion Inc.
 st	STMicroelectronics
 ste	ST-Ericsson
 stericsson	ST-Ericsson
+synology	Synology, Inc.
 ti	Texas Instruments
 tlm	Trusted Logic Mobility
 toshiba	Toshiba Corporation
 toumaz	Toumaz
 v3	V3 Semiconductor
 via	VIA Technologies, Inc.
+voipac	Voipac Technologies s.r.o.
 winbond Winbond Electronics corp.
 wlf	Wolfson Microelectronics
 wm	Wondermedia Technologies, Inc.

arch/arm/boot/dts/Makefile

@@ -51,19 +51,15 @@ dtb-$(CONFIG_ARCH_AT91)	+= sama5d36ek.dtb
 
 dtb-$(CONFIG_ARCH_ATLAS6) += atlas6-evb.dtb
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
-dtb-$(CONFIG_ARCH_BCM_MOBILE) += bcm11351-brt.dtb \
-	bcm28155-ap.dtb
+dtb-$(CONFIG_ARCH_BCM_MOBILE) += bcm28155-ap.dtb \
+	bcm21664-garnet.dtb
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
+dtb-$(CONFIG_ARCH_BCM_5301X) += bcm4708-netgear-r6250.dtb
 dtb-$(CONFIG_ARCH_BERLIN) += \
 	berlin2-sony-nsz-gs7.dtb	\
 	berlin2cd-google-chromecast.dtb
 dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \
 	da850-evm.dtb
-dtb-$(CONFIG_MACH_DOVE) += dove-cm-a510.dtb \
-	dove-cubox.dtb \
-	dove-d2plug.dtb \
-	dove-d3plug.dtb \
-	dove-dove-db.dtb
 dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb
 dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos4210-smdkv310.dtb \
@@ -86,7 +82,11 @@ dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb \
 	ecx-2000.dtb
 dtb-$(CONFIG_ARCH_INTEGRATOR) += integratorap.dtb \
 	integratorcp.dtb
+dtb-$(CONFIG_ARCH_KEYSTONE) += k2hk-evm.dtb \
+	k2l-evm.dtb \
+	k2e-evm.dtb
 kirkwood := \
+	kirkwood-b3.dtb \
 	kirkwood-cloudbox.dtb \
 	kirkwood-db-88f6281.dtb \
 	kirkwood-db-88f6282.dtb \
@@ -94,6 +94,18 @@ kirkwood := \
 	kirkwood-dns325.dtb \
 	kirkwood-dockstar.dtb \
 	kirkwood-dreamplug.dtb \
+	kirkwood-ds109.dtb \
+	kirkwood-ds110jv10.dtb \
+	kirkwood-ds111.dtb \
+	kirkwood-ds209.dtb \
+	kirkwood-ds210.dtb \
+	kirkwood-ds212.dtb \
+	kirkwood-ds212j.dtb \
+	kirkwood-ds409.dtb \
+	kirkwood-ds409slim.dtb \
+	kirkwood-ds411.dtb \
+	kirkwood-ds411j.dtb \
+	kirkwood-ds411slim.dtb \
 	kirkwood-goflexnet.dtb \
 	kirkwood-guruplug-server-plus.dtb \
 	kirkwood-ib62x0.dtb \
@@ -116,54 +128,74 @@ kirkwood := \
 	kirkwood-nsa310a.dtb \
 	kirkwood-openblocks_a6.dtb \
 	kirkwood-openblocks_a7.dtb \
+	kirkwood-rd88f6192.dtb \
+	kirkwood-rd88f6281-a0.dtb \
+	kirkwood-rd88f6281-a1.dtb \
+	kirkwood-rs212.dtb \
+	kirkwood-rs409.dtb \
+	kirkwood-rs411.dtb \
 	kirkwood-sheevaplug.dtb \
 	kirkwood-sheevaplug-esata.dtb \
+	kirkwood-t5325.dtb \
 	kirkwood-topkick.dtb \
 	kirkwood-ts219-6281.dtb \
-	kirkwood-ts219-6282.dtb
+	kirkwood-ts219-6282.dtb \
+	kirkwood-ts419-6281.dtb \
+	kirkwood-ts419-6282.dtb
 dtb-$(CONFIG_ARCH_KIRKWOOD) += $(kirkwood)
 dtb-$(CONFIG_MACH_KIRKWOOD) += $(kirkwood)
 dtb-$(CONFIG_ARCH_LPC32XX) += ea3250.dtb phy3250.dtb
 dtb-$(CONFIG_ARCH_MARCO) += marco-evb.dtb
 dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb
-dtb-$(CONFIG_ARCH_MVEBU) += armada-370-db.dtb \
-	armada-370-mirabox.dtb \
-	armada-370-netgear-rn102.dtb \
-	armada-370-netgear-rn104.dtb \
-	armada-370-rd.dtb \
-	armada-xp-axpwifiap.dtb \
-	armada-xp-db.dtb \
-	armada-xp-gp.dtb \
-	armada-xp-netgear-rn2120.dtb \
-	armada-xp-matrix.dtb \
-	armada-xp-openblocks-ax3-4.dtb
 dtb-$(CONFIG_ARCH_MXC) += \
+	imx25-eukrea-mbimxsd25-baseboard.dtb \
 	imx25-karo-tx25.dtb \
 	imx25-pdk.dtb \
 	imx27-apf27.dtb \
 	imx27-apf27dev.dtb \
 	imx27-pdk.dtb \
-	imx27-phytec-phycore-som.dtb \
 	imx27-phytec-phycore-rdk.dtb \
-	imx27-phytec-phycard-s-som.dtb \
 	imx27-phytec-phycard-s-rdk.dtb \
 	imx31-bug.dtb \
+	imx35-eukrea-mbimxsd35-baseboard.dtb \
+	imx50-evk.dtb \
 	imx51-apf51.dtb \
 	imx51-apf51dev.dtb \
 	imx51-babbage.dtb \
+	imx51-eukrea-mbimxsd51-baseboard.dtb \
 	imx53-ard.dtb \
-	imx53-evk.dtb \
 	imx53-m53evk.dtb \
 	imx53-mba53.dtb \
 	imx53-qsb.dtb \
+	imx53-qsrb.dtb \
 	imx53-smd.dtb \
+	imx53-tx53-x03x.dtb \
+	imx53-tx53-x13x.dtb \
+	imx53-voipac-bsb.dtb \
 	imx6dl-cubox-i.dtb \
+	imx6dl-dfi-fs700-m60.dtb \
+	imx6dl-gw51xx.dtb \
+	imx6dl-gw52xx.dtb \
+	imx6dl-gw53xx.dtb \
+	imx6dl-gw54xx.dtb \
 	imx6dl-hummingboard.dtb \
+	imx6dl-nitrogen6x.dtb \
 	imx6dl-sabreauto.dtb \
+	imx6dl-sabrelite.dtb \
 	imx6dl-sabresd.dtb \
 	imx6dl-wandboard.dtb \
 	imx6q-arm2.dtb \
+	imx6q-cm-fx6.dtb \
 	imx6q-cubox-i.dtb \
+	imx6q-dfi-fs700-m60.dtb \
+	imx6q-dmo-edmqmx6.dtb \
+	imx6q-gk802.dtb \
+	imx6q-gw51xx.dtb \
+	imx6q-gw52xx.dtb \
+	imx6q-gw53xx.dtb \
+	imx6q-gw5400-a.dtb \
+	imx6q-gw54xx.dtb \
+	imx6q-nitrogen6x.dtb \
 	imx6q-phytec-pbab01.dtb \
 	imx6q-sabreauto.dtb \
 	imx6q-sabrelite.dtb \
@@ -187,6 +219,9 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx28-cfa10056.dtb \
 	imx28-cfa10057.dtb \
 	imx28-cfa10058.dtb \
+	imx28-duckbill.dtb \
+	imx28-eukrea-mbmx283lc.dtb \
+	imx28-eukrea-mbmx287lc.dtb \
 	imx28-evk.dtb \
 	imx28-m28cu3.dtb \
 	imx28-m28evk.dtb \
@@ -203,6 +238,10 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap2420-n810-wimax.dtb \
 	omap3430-sdp.dtb \
 	omap3-beagle.dtb \
+	omap3-cm-t3517.dtb \
+	omap3-sbc-t3517.dtb \
+	omap3-cm-t3530.dtb \
+	omap3-sbc-t3530.dtb \
 	omap3-cm-t3730.dtb \
 	omap3-sbc-t3730.dtb \
 	omap3-devkit8000.dtb \
@@ -213,12 +252,24 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap3-n900.dtb \
 	omap3-n9.dtb \
 	omap3-n950.dtb \
+	omap3-overo-alto35.dtb \
+	omap3-overo-storm-alto35.dtb \
+	omap3-overo-chestnut43.dtb \
+	omap3-overo-storm-chestnut43.dtb \
+	omap3-overo-gallop43.dtb \
+	omap3-overo-storm-gallop43.dtb \
+	omap3-overo-palo43.dtb \
+	omap3-overo-storm-palo43.dtb \
+	omap3-overo-summit.dtb \
+	omap3-overo-storm-summit.dtb \
 	omap3-overo-tobi.dtb \
 	omap3-overo-storm-tobi.dtb \
 	omap3-gta04.dtb \
 	omap3-igep0020.dtb \
 	omap3-igep0030.dtb \
+	omap3-lilly-dbb056.dtb \
 	omap3-zoom3.dtb \
+	omap4-duovero-parlor.dtb \
 	omap4-panda.dtb \
 	omap4-panda-a4.dtb \
 	omap4-panda-es.dtb \
@@ -232,9 +283,11 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	am335x-boneblack.dtb \
 	am335x-nano.dtb \
 	am335x-base0033.dtb \
+	am3517-craneboard.dtb \
 	am3517-evm.dtb \
 	am3517_mt_ventoux.dtb \
 	am43x-epos-evm.dtb \
+	am437x-gp-evm.dtb \
 	dra7-evm.dtb
 dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
 dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
@@ -291,6 +344,9 @@ dtb-$(CONFIG_ARCH_SUNXI) += \
 	sun4i-a10-cubieboard.dtb \
 	sun4i-a10-mini-xplus.dtb \
 	sun4i-a10-hackberry.dtb \
+	sun4i-a10-inet97fv2.dtb \
+	sun4i-a10-olinuxino-lime.dtb \
+	sun4i-a10-pcduino.dtb \
 	sun5i-a10s-olinuxino-micro.dtb \
 	sun5i-a13-olinuxino.dtb \
 	sun5i-a13-olinuxino-micro.dtb \
@@ -329,6 +385,29 @@ dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \
 dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
 	zynq-zc706.dtb \
 	zynq-zed.dtb
+dtb-$(CONFIG_MACH_ARMADA_370) += \
+	armada-370-db.dtb \
+	armada-370-mirabox.dtb \
+	armada-370-netgear-rn102.dtb \
+	armada-370-netgear-rn104.dtb \
+	armada-370-rd.dtb
+dtb-$(CONFIG_MACH_ARMADA_375) += \
+	armada-375-db.dtb
+dtb-$(CONFIG_MACH_ARMADA_38X) += \
+	armada-385-db.dtb \
+	armada-385-rd.dtb
+dtb-$(CONFIG_MACH_ARMADA_XP) += \
+	armada-xp-axpwifiap.dtb \
+	armada-xp-db.dtb \
+	armada-xp-gp.dtb \
+	armada-xp-netgear-rn2120.dtb \
+	armada-xp-matrix.dtb \
+	armada-xp-openblocks-ax3-4.dtb
+dtb-$(CONFIG_MACH_DOVE) += dove-cm-a510.dtb \
+	dove-cubox.dtb \
+	dove-d2plug.dtb \
+	dove-d3plug.dtb \
+	dove-dove-db.dtb
 
 targets += dtbs dtbs_install
 targets += $(dtb-y)

arch/arm/boot/dts/am335x-evm.dts

@@ -260,6 +260,12 @@
 		>;
 	};
 
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
+		>;
+	};
+
 	lcd_pins_s0: lcd_pins_s0 {
 		pinctrl-single,pins = <
 			0x20 0x01	/* gpmc_ad8.lcd_data16, OUTPUT | MODE1 */
@@ -434,9 +440,9 @@
 	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
 	nand@0,0 {
 		reg = <0 0 0>; /* CS0, offset 0 */
-		nand-bus-width = <8>;
 		ti,nand-ecc-opt = "bch8";
-		gpmc,device-nand = "true";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
 		gpmc,device-width = <1>;
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
@@ -460,50 +466,51 @@
 		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-access-ns = <40>;
 		gpmc,wr-data-mux-bus-ns = <0>;
-
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
 		#address-cells = <1>;
 		#size-cells = <1>;
-		elm_id = <&elm>;
-
-		/* MTD partition table */
 		partition@0 {
-			label = "SPL1";
+			label = "NAND.SPL";
 			reg = <0x00000000 0x000020000>;
 		};
-
 		partition@1 {
-			label = "SPL2";
+			label = "NAND.SPL.backup1";
 			reg = <0x00020000 0x00020000>;
 		};
-
 		partition@2 {
-			label = "SPL3";
+			label = "NAND.SPL.backup2";
 			reg = <0x00040000 0x00020000>;
 		};
-
 		partition@3 {
-			label = "SPL4";
+			label = "NAND.SPL.backup3";
 			reg = <0x00060000 0x00020000>;
 		};
-
 		partition@4 {
-			label = "U-boot";
-			reg = <0x00080000 0x001e0000>;
+			label = "NAND.u-boot-spl";
+			reg = <0x00080000 0x00040000>;
 		};
-
 		partition@5 {
-			label = "environment";
-			reg = <0x00260000 0x00020000>;
+			label = "NAND.u-boot";
+			reg = <0x000C0000 0x00100000>;
 		};
-
 		partition@6 {
-			label = "Kernel";
-			reg = <0x00280000 0x00500000>;
+			label = "NAND.u-boot-env";
+			reg = <0x001C0000 0x00020000>;
 		};
-
 		partition@7 {
-			label = "File-System";
-			reg = <0x00780000 0x0F880000>;
+			label = "NAND.u-boot-env.backup1";
+			reg = <0x001E0000 0x00020000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00200000 0x00800000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00A00000 0x0F600000>;
 		};
 	};
 };
@@ -643,6 +650,9 @@
 	status = "okay";
 	vmmc-supply = <&vmmc_reg>;
 	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
 };
 
 &sham {

arch/arm/boot/dts/am335x-evmsk.dts

@@ -45,6 +45,18 @@
 		regulator-boot-on;
 	};
 
+	wl12xx_vmmc: fixedregulator@2 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wl12xx_gpio>;
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio1 29 0>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
 	leds {
 		pinctrl-names = "default";
 		pinctrl-0 = <&user_leds_s0>;
@@ -270,6 +282,24 @@
 			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
 		>;
 	};
+
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_31 */
+			0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+			0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+			0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+			0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+			0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+			0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+		>;
+	};
+
+	wl12xx_gpio: pinmux_wl12xx_gpio {
+		pinctrl-single,pins = <
+			0x7c (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_csn0.gpio1_29 */
+		>;
+	};
 };
 
 &uart0 {
@@ -342,9 +372,22 @@
 		status = "okay";
 	};
 
+	usb-phy@47401b00 {
+		status = "okay";
+	};
+
 	usb@47401000 {
 		status = "okay";
 	};
+
+	usb@47401800 {
+		status = "okay";
+		dr_mode = "host";
+	};
+
+	dma-controller@07402000  {
+		status = "okay";
+	};
 };
 
 &epwmss2 {
@@ -440,6 +483,7 @@
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
+	dual_emac = <1>;
 };
 
 &davinci_mdio {
@@ -451,11 +495,13 @@
 &cpsw_emac0 {
 	phy_id = <&davinci_mdio>, <0>;
 	phy-mode = "rgmii-txid";
+	dual_emac_res_vlan = <1>;
 };
 
 &cpsw_emac1 {
 	phy_id = <&davinci_mdio>, <1>;
 	phy-mode = "rgmii-txid";
+	dual_emac_res_vlan = <2>;
 };
 
 &mmc1 {
@@ -479,6 +525,16 @@
 	ti,no-reset-on-init;
 };
 
+&mmc2 {
+	status = "okay";
+	vmmc-supply = <&wl12xx_vmmc>;
+	ti,non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+};
+
 &mcasp1 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&mcasp1_pins>;

arch/arm/boot/dts/am33xx.dtsi

@@ -58,6 +58,10 @@
 				275000  1125000
 			>;
 			voltage-tolerance = <2>; /* 2 percentage */
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
 			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 	};
@@ -318,6 +322,7 @@
 			compatible = "ti,omap4-hwspinlock";
 			reg = <0x480ca000 0x1000>;
 			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
 		};
 
 		wdt2: wdt@44e35000 {
@@ -399,7 +404,7 @@
 			ti,timer-pwm;
 		};
 
-		rtc@44e3e000 {
+		rtc: rtc@44e3e000 {
 			compatible = "ti,da830-rtc";
 			reg = <0x44e3e000 0x1000>;
 			interrupts = <75
@@ -582,6 +587,8 @@
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48300100 0x80>;
+				interrupts = <31>;
+				interrupt-names = "ecap0";
 				ti,hwmods = "ecap0";
 				status = "disabled";
 			};
@@ -610,6 +617,8 @@
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48302100 0x80>;
+				interrupts = <47>;
+				interrupt-names = "ecap1";
 				ti,hwmods = "ecap1";
 				status = "disabled";
 			};
@@ -638,6 +647,8 @@
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48304100 0x80>;
+				interrupts = <61>;
+				interrupt-names = "ecap2";
 				ti,hwmods = "ecap2";
 				status = "disabled";
 			};

arch/arm/boot/dts/am3517-craneboard.dts

@@ -0,0 +1,174 @@
+/*
+ * See craneboard.org for more details
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am3517.dtsi"
+
+/ {
+	model = "TI AM3517 CraneBoard (TMDSEVM3517)";
+	compatible = "ti,am3517-craneboard", "ti,am3517", "ti,omap3";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;	/* 256 MB */
+	};
+
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+};
+
+&davinci_emac {
+	status = "okay";
+};
+
+&davinci_mdio {
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	tps: tps@2d {
+		reg = <0x2d>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+&mmc1 {
+	vmmc-supply = <&vdd2_reg>;
+	bus-width = <8>;
+};
+
+&mmc2 {
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+&mmc3 {
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+#include "tps65910.dtsi"
+
+&omap3_pmx_core {
+	tps_pins: pinmux_tps_pins {
+		pinctrl-single,pins = <
+			0x1b0 (PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq.sys_nirq */
+		>;
+	};
+};
+
+&tps {
+	pinctrl-names = "default";
+	pinctrl-0 = <&tps_pins>;
+
+	interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+	interrupt-parent = <&intc>;
+
+	ti,en-ck32k-xtal;
+
+	vcc1-supply = <&vbat>;
+	vcc2-supply = <&vbat>;
+	vcc3-supply = <&vbat>;
+	vcc4-supply = <&vbat>;
+	vcc5-supply = <&vbat>;
+	vcc6-supply = <&vbat>;
+	vcc7-supply = <&vbat>;
+	vccio-supply = <&vbat>;
+
+	regulators {
+		vrtc_reg: regulator@0 {
+			regulator-always-on;
+		};
+
+		vio_reg: regulator@1 {
+			regulator-always-on;
+		};
+
+		/*
+		 * Unused:
+		 * VDIG1=2.7V,300mA max
+		 * VDIG2=1.8V,300mA max
+		 */
+
+		vpll_reg: regulator@7 {
+			/* VDDS_DPLL_1V8 */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vaux1_reg: regulator@9 {
+			/* VDDS_SRAM_1V8 */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vaux2_reg: regulator@10 {
+			/* VDDA1P8V_USBPHY */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		/* VAUX33 unused */
+
+		vdac_reg: regulator@8 {
+			/* VDDA_DAC_1V8 */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vmmc_reg: regulator@12 {
+			/* VDDA3P3V_USBPHY */
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		vdd1_reg: regulator@2 {
+			/* VDD_CORE */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd2_reg: regulator@3 {
+			/* VDDSHV_3V3 */
+			regulator-name = "vdd_shv";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		/* VDD3 unused */
+	};
+};

arch/arm/boot/dts/am4372.dtsi

@@ -8,6 +8,7 @@
  * kind, whether express or implied.
  */
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
 #include "skeleton.dtsi"
@@ -33,6 +34,11 @@
 			compatible = "arm,cortex-a9";
 			device_type = "cpu";
 			reg = <0>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 	};
 
@@ -351,6 +357,13 @@
 			status = "disabled";
 		};
 
+		hwspinlock: spinlock@480ca000 {
+			compatible = "ti,omap4-hwspinlock";
+			reg = <0x480ca000 0x1000>;
+			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
+		};
+
 		i2c0: i2c@44e0b000 {
 			compatible = "ti,am4372-i2c","ti,omap4-i2c";
 			reg = <0x44e0b000 0x1000>;
@@ -521,6 +534,7 @@
 
 			ecap0: ecap@48300100 {
 				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
 				reg = <0x48300100 0x80>;
 				ti,hwmods = "ecap0";
 				status = "disabled";
@@ -528,6 +542,7 @@
 
 			ehrpwm0: ehrpwm@48300200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48300200 0x80>;
 				ti,hwmods = "ehrpwm0";
 				status = "disabled";
@@ -545,6 +560,7 @@
 
 			ecap1: ecap@48302100 {
 				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
 				reg = <0x48302100 0x80>;
 				ti,hwmods = "ecap1";
 				status = "disabled";
@@ -552,6 +568,7 @@
 
 			ehrpwm1: ehrpwm@48302200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48302200 0x80>;
 				ti,hwmods = "ehrpwm1";
 				status = "disabled";
@@ -569,6 +586,7 @@
 
 			ecap2: ecap@48304100 {
 				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
 				reg = <0x48304100 0x80>;
 				ti,hwmods = "ecap2";
 				status = "disabled";
@@ -576,6 +594,7 @@
 
 			ehrpwm2: ehrpwm@48304200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48304200 0x80>;
 				ti,hwmods = "ehrpwm2";
 				status = "disabled";
@@ -593,6 +612,7 @@
 
 			ehrpwm3: ehrpwm@48306200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48306200 0x80>;
 				ti,hwmods = "ehrpwm3";
 				status = "disabled";
@@ -610,6 +630,7 @@
 
 			ehrpwm4: ehrpwm@48308200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48308200 0x80>;
 				ti,hwmods = "ehrpwm4";
 				status = "disabled";
@@ -627,6 +648,7 @@
 
 			ehrpwm5: ehrpwm@4830a200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x4830a200 0x80>;
 				ti,hwmods = "ehrpwm5";
 				status = "disabled";
@@ -689,6 +711,30 @@
 			       <&edma 11>;
 			dma-names = "tx", "rx";
 		};
+
+		elm: elm@48080000 {
+			compatible = "ti,am3352-elm";
+			reg = <0x48080000 0x2000>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "elm";
+			clocks = <&l4ls_gclk>;
+			clock-names = "fck";
+			status = "disabled";
+		};
+
+		gpmc: gpmc@50000000 {
+			compatible = "ti,am3352-gpmc";
+			ti,hwmods = "gpmc";
+			clocks = <&l3s_gclk>;
+			clock-names = "fck";
+			reg = <0x50000000 0x2000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			gpmc,num-cs = <7>;
+			gpmc,num-waitpins = <2>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			status = "disabled";
+		};
 	};
 };
 

arch/arm/boot/dts/am437x-gp-evm.dts

@@ -0,0 +1,127 @@
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/* AM437x GP EVM */
+
+/dts-v1/;
+
+#include "am4372.dtsi"
+#include <dt-bindings/pinctrl/am43xx.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "TI AM437x GP EVM";
+	compatible = "ti,am437x-gp-evm","ti,am4372","ti,am43";
+
+	vmmcsd_fixed: fixedregulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
+
+	matrix_keypad: matrix_keypad@0 {
+		compatible = "gpio-matrix-keypad";
+		debounce-delay-ms = <5>;
+		col-scan-delay-us = <2>;
+
+		row-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH /* Bank3, pin21 */
+				&gpio4 3 GPIO_ACTIVE_HIGH /* Bank4, pin3 */
+				&gpio4 2 GPIO_ACTIVE_HIGH>; /* Bank4, pin2 */
+
+		col-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH /* Bank3, pin19 */
+				&gpio3 20 GPIO_ACTIVE_HIGH>; /* Bank3, pin20 */
+
+		linux,keymap = <0x00000201      /* P1 */
+				0x00010202      /* P2 */
+				0x01000067      /* UP */
+				0x0101006a      /* RIGHT */
+				0x02000069      /* LEFT */
+				0x0201006c>;      /* DOWN */
+		};
+};
+
+&am43xx_pinmux {
+	i2c0_pins: i2c0_pins {
+		pinctrl-single,pins = <
+			0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_sda.i2c0_sda */
+			0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_scl.i2c0_scl */
+		>;
+	};
+
+	i2c1_pins: i2c1_pins {
+		pinctrl-single,pins = <
+			0x15c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_cs0.i2c1_scl */
+			0x158 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_d1.i2c1_sda  */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
+		>;
+	};
+
+	ecap0_pins: backlight_pins {
+		pinctrl-single,pins = <
+			0x164 MUX_MODE0       /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+		>;
+	};
+};
+
+&i2c0 {
+        status = "okay";
+        pinctrl-names = "default";
+        pinctrl-0 = <&i2c0_pins>;
+};
+
+&i2c1 {
+        status = "okay";
+        pinctrl-names = "default";
+        pinctrl-0 = <&i2c1_pins>;
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&ecap0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ecap0_pins>;
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio3 {
+	status = "okay";
+};
+
+&gpio4 {
+	status = "okay";
+};
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+};

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -13,6 +13,7 @@
 #include "am4372.dtsi"
 #include <dt-bindings/pinctrl/am43xx.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "TI AM43x EPOS EVM";
@@ -79,6 +80,64 @@
 				0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
 			>;
 		};
+
+		nand_flash_x8: nand_flash_x8 {
+			pinctrl-single,pins = <
+				0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a0.SELQSPIorNAND/GPIO */
+				0x0  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
+				0x4  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
+				0x8  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
+				0xc  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
+				0x10 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
+				0x14 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
+				0x18 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
+				0x1c (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
+				0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
+				0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_wpn.gpmc_wpn */
+				0x7c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0  */
+				0x90 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
+				0x94 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
+				0x98 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
+				0x9c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_be0n_cle.gpmc_be0n_cle */
+			>;
+		};
+
+		ecap0_pins: backlight_pins {
+			pinctrl-single,pins = <
+				0x164 MUX_MODE0         /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+			>;
+		};
+
+		i2c2_pins: pinmux_i2c2_pins {
+			pinctrl-single,pins = <
+				0x1c0 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8)    /* i2c2_sda.i2c2_sda */
+				0x1c4 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8)    /* i2c2_scl.i2c2_scl */
+			>;
+		};
+
+		spi0_pins: pinmux_spi0_pins {
+			pinctrl-single,pins = <
+				0x150 (PIN_INPUT | MUX_MODE0)           /* spi0_clk.spi0_clk */
+				0x154 (PIN_OUTPUT | MUX_MODE0)           /* spi0_d0.spi0_d0 */
+				0x158 (PIN_INPUT | MUX_MODE0)           /* spi0_d1.spi0_d1 */
+				0x15c (PIN_OUTPUT | MUX_MODE0)          /* spi0_cs0.spi0_cs0 */
+			>;
+		};
+
+		spi1_pins: pinmux_spi1_pins {
+			pinctrl-single,pins = <
+				0x190 (PIN_INPUT | MUX_MODE3)           /* mcasp0_aclkx.spi1_clk */
+				0x194 (PIN_OUTPUT | MUX_MODE3)           /* mcasp0_fsx.spi1_d0 */
+				0x198 (PIN_INPUT | MUX_MODE3)           /* mcasp0_axr0.spi1_d1 */
+				0x19c (PIN_OUTPUT | MUX_MODE3)          /* mcasp0_ahclkr.spi1_cs0 */
+			>;
+		};
+
+		mmc1_pins: pinmux_mmc1_pins {
+			pinctrl-single,pins = <
+				0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
+			>;
+		};
 	};
 
 	matrix_keypad: matrix_keypad@0 {
@@ -113,12 +172,22 @@
 				0x0203006c	/* DOWN */
 				0x03030069>;	/* LEFT */
 		};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
 };
 
 &mmc1 {
 	status = "okay";
 	vmmc-supply = <&vmmcsd_fixed>;
 	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
 };
 
 &mac {
@@ -169,6 +238,12 @@
 	};
 };
 
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+	status = "okay";
+};
+
 &gpio0 {
 	status = "okay";
 };
@@ -184,3 +259,111 @@
 &gpio3 {
 	status = "okay";
 };
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_flash_x8>;
+	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+	nand@0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <40>; /* tCEA + tCHZ + 1 */
+		gpmc,cs-wr-off-ns = <40>;
+		gpmc,adv-on-ns = <0>;  /* cs-on-ns */
+		gpmc,adv-rd-off-ns = <25>; /* min( tALH + tALS + 1) */
+		gpmc,adv-wr-off-ns = <25>; /* min( tALH + tALS + 1) */
+		gpmc,we-on-ns = <0>;   /* cs-on-ns */
+		gpmc,we-off-ns = <20>; /* we-on-time + tWP + 2 */
+		gpmc,oe-on-ns = <3>;  /* cs-on-ns + tRR + 2 */
+		gpmc,oe-off-ns = <30>; /* oe-on-ns + tRP + 2 */
+		gpmc,access-ns = <30>; /* tCEA + 4*/
+		gpmc,rd-cycle-ns = <40>;
+		gpmc,wr-cycle-ns = <40>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "NAND.SPL";
+			reg = <0x00000000 0x00040000>;
+		};
+		partition@1 {
+			label = "NAND.SPL.backup1";
+			reg = <0x00040000 0x00040000>;
+		};
+		partition@2 {
+			label = "NAND.SPL.backup2";
+			reg = <0x00080000 0x00040000>;
+		};
+		partition@3 {
+			label = "NAND.SPL.backup3";
+			reg = <0x000C0000 0x00040000>;
+		};
+		partition@4 {
+			label = "NAND.u-boot-spl-os";
+			reg = <0x00100000 0x00080000>;
+		};
+		partition@5 {
+			label = "NAND.u-boot";
+			reg = <0x00180000 0x00100000>;
+		};
+		partition@6 {
+			label = "NAND.u-boot-env";
+			reg = <0x00280000 0x00040000>;
+		};
+		partition@7 {
+			label = "NAND.u-boot-env.backup1";
+			reg = <0x002C0000 0x00040000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00300000 0x00700000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00800000 0x1F600000>;
+		};
+	};
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&ecap0 {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ecap0_pins>;
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins>;
+	status = "okay";
+};

arch/arm/boot/dts/armada-370-db.dts

@@ -64,6 +64,22 @@
 				phy-mode = "rgmii-id";
 			};
 
+			i2c@11000 {
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				audio_codec: audio-codec@4a {
+					compatible = "cirrus,cs42l51";
+					reg = <0x4a>;
+				};
+			};
+
+			audio-controller@30000 {
+				pinctrl-0 = <&i2s_pins2>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
 			mvsdio@d4000 {
 				pinctrl-0 = <&sdio_pins1>;
 				pinctrl-names = "default";
@@ -80,6 +96,30 @@
 				broken-cd;
 			};
 
+			pinctrl {
+				/*
+				 * These pins might be muxed as I2S by
+				 * the bootloader, but it conflicts
+				 * with the real I2S pins that are
+				 * muxed using i2s_pins. We must mux
+				 * those pins to a function other than
+				 * I2S.
+				 */
+				pinctrl-0 = <&hog_pins1 &hog_pins2>;
+				pinctrl-names = "default";
+
+				hog_pins1: hog-pins1 {
+					marvell,pins = "mpp6",  "mpp8", "mpp10",
+						       "mpp12", "mpp13";
+					marvell,function = "gpio";
+				};
+
+				hog_pins2: hog-pins2 {
+					marvell,pins = "mpp5", "mpp7", "mpp9";
+					marvell,function = "gpo";
+				};
+			};
+
 			usb@50000 {
 				status = "okay";
 			};
@@ -112,10 +152,26 @@
 				/* Port 0, Lane 0 */
 				status = "okay";
 			};
+
 			pcie@2,0 {
 				/* Port 1, Lane 0 */
 				status = "okay";
 			};
 		};
 	};
+
+	sound {
+	      compatible = "marvell,a370db-audio";
+	      marvell,audio-controller = <&audio_controller>;
+	      marvell,audio-codec = <&audio_codec &spdif_out &spdif_in>;
+	      status = "okay";
+	};
+
+	spdif_out: spdif-out {
+	      compatible = "linux,spdif-dit";
+	};
+
+	spdif_in: spdif-in {
+	      compatible = "linux,spdif-dir";
+	};
 };

arch/arm/boot/dts/armada-370-mirabox.dts

@@ -9,6 +9,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "armada-370.dtsi"
 
 / {
@@ -73,19 +74,19 @@
 
 				green_pwr_led {
 					label = "mirabox:green:pwr";
-					gpios = <&gpio1 31 1>;
+					gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
 					default-state = "keep";
 				};
 
 				blue_stat_led {
 					label = "mirabox:blue:stat";
-					gpios = <&gpio2 0 1>;
+					gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
 					default-state = "off";
 				};
 
 				green_stat_led {
 					label = "mirabox:green:stat";
-					gpios = <&gpio2 1 1>;
+					gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
 					default-state = "off";
 				};
 			};

arch/arm/boot/dts/armada-370-rd.dts

@@ -12,6 +12,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
 #include "armada-370.dtsi"
 
 / {
@@ -100,8 +102,8 @@
 				#size-cells = <0>;
 				button@1 {
 					label = "Software Button";
-					linux,code = <116>;
-					gpios = <&gpio0 6 1>;
+					linux,code = <KEY_POWER>;
+					gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
 				};
 			};
 

arch/arm/boot/dts/armada-370-xp.dtsi

@@ -44,8 +44,8 @@
 		#size-cells = <1>;
 		controller = <&mbusc>;
 		interrupt-parent = <&mpic>;
-		pcie-mem-aperture = <0xe0000000 0x8000000>;
-		pcie-io-aperture  = <0xe8000000 0x100000>;
+		pcie-mem-aperture = <0xf8000000 0x7e00000>;
+		pcie-io-aperture  = <0xffe00000 0x100000>;
 
 		devbus-bootcs {
 			compatible = "marvell,mvebu-devbus";
@@ -199,6 +199,10 @@
 				interrupts = <37>, <38>, <39>, <40>, <5>, <6>;
 			};
 
+			watchdog@20300 {
+				reg = <0x20300 0x34>, <0x20704 0x4>;
+			};
+
 			usb@50000 {
 				compatible = "marvell,orion-ehci";
 				reg = <0x50000 0x500>;

arch/arm/boot/dts/armada-370.dtsi

@@ -132,6 +132,25 @@
 							"mpp51", "mpp52", "mpp53";
 					marvell,function = "sd0";
 				};
+
+				i2c0_pins: i2c0-pins {
+					marvell,pins = "mpp2", "mpp3";
+					marvell,function = "i2c0";
+				};
+
+				i2s_pins1: i2s-pins1 {
+					marvell,pins = "mpp5", "mpp6", "mpp7",
+						       "mpp8", "mpp9", "mpp10",
+						       "mpp12", "mpp13";
+					marvell,function = "audio";
+				};
+
+				i2s_pins2: i2s-pins2 {
+					marvell,pins = "mpp49", "mpp47", "mpp50",
+						       "mpp59", "mpp57", "mpp61",
+						       "mpp62", "mpp60", "mpp58";
+					marvell,function = "audio";
+				};
 			};
 
 			gpio0: gpio@18100 {
@@ -196,6 +215,20 @@
 				clocks = <&coreclk 2>;
 			};
 
+			watchdog@20300 {
+				compatible = "marvell,armada-370-wdt";
+				clocks = <&coreclk 2>;
+			};
+
+			audio_controller: audio-controller@30000 {
+				compatible = "marvell,armada370-audio";
+				reg = <0x30000 0x4000>;
+				interrupts = <93>;
+				clocks = <&gateclk 0>;
+				clock-names = "internal";
+				status = "disabled";
+			};
+
 			usb@50000 {
 				clocks = <&coreclk 0>;
 			};

arch/arm/boot/dts/armada-375-db.dts

@@ -0,0 +1,130 @@
+/*
+ * Device Tree file for Marvell Armada 375 evaluation board
+ * (DB-88F6720)
+ *
+ *  Copyright (C) 2014 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-375.dtsi"
+
+/ {
+	model = "Marvell Armada 375 Development Board";
+	compatible = "marvell,a375-db", "marvell,armada375";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>; /* 1 GB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+			spi@10600 {
+				pinctrl-0 = <&spi0_pins>;
+				pinctrl-names = "default";
+				/*
+				 * SPI conflicts with NAND, so we disable it
+				 * here, and select NAND as the enabled device
+				 * by default.
+				 */
+				status = "disabled";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "n25q128a13";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <108000000>;
+				};
+			};
+
+			i2c@11000 {
+				status = "okay";
+				clock-frequency = <100000>;
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-names = "default";
+			};
+
+			i2c@11100 {
+				status = "okay";
+				clock-frequency = <100000>;
+				pinctrl-0 = <&i2c1_pins>;
+				pinctrl-names = "default";
+			};
+
+			serial@12000 {
+				clock-frequency = <200000000>;
+				status = "okay";
+			};
+
+			pinctrl {
+				sdio_st_pins: sdio-st-pins {
+					marvell,pins = "mpp44", "mpp45";
+					marvell,function = "gpio";
+				};
+			};
+
+			nand: nand@d0000 {
+				pinctrl-0 = <&nand_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+
+				partition@0 {
+					label = "U-Boot";
+					reg = <0 0x800000>;
+				};
+				partition@800000 {
+					label = "Linux";
+					reg = <0x800000 0x800000>;
+				};
+				partition@1000000 {
+					label = "Filesystem";
+					reg = <0x1000000 0x3f000000>;
+				};
+			};
+
+			mvsdio@d4000 {
+				pinctrl-0 = <&sdio_pins &sdio_st_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				cd-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+				wp-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+			/*
+			 * The two PCIe units are accessible through
+			 * standard PCIe slots on the board.
+			 */
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+			pcie@2,0 {
+				/* Port 1, Lane 0 */
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/armada-375.dtsi

@@ -0,0 +1,464 @@
+/*
+ * Device Tree Include file for Marvell Armada 375 family SoC
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
+/ {
+	model = "Marvell Armada 375 family SoC";
+	compatible = "marvell,armada375";
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+	};
+
+	clocks {
+		/* 2 GHz fixed main PLL */
+		mainpll: mainpll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <2000000000>;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+		};
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <1>;
+		};
+	};
+
+	soc {
+		compatible = "marvell,armada375-mbus", "marvell,armada370-mbus", "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		controller = <&mbusc>;
+		interrupt-parent = <&gic>;
+		pcie-mem-aperture = <0xe0000000 0x8000000>;
+		pcie-io-aperture  = <0xe8000000 0x100000>;
+
+		bootrom {
+			compatible = "marvell,bootrom";
+			reg = <MBUS_ID(0x01, 0x1d) 0 0x100000>;
+		};
+
+		devbus-bootcs {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10400 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x2f) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs0 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10408 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3e) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs1 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10410 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3d) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs2 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10418 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3b) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs3 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10420 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x37) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		internal-regs {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
+
+			L2: cache-controller@8000 {
+				compatible = "arm,pl310-cache";
+				reg = <0x8000 0x1000>;
+				cache-unified;
+				cache-level = <2>;
+			};
+
+			timer@c600 {
+				compatible = "arm,cortex-a9-twd-timer";
+				reg = <0xc600 0x20>;
+				interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>;
+				clocks = <&coreclk 2>;
+			};
+
+			gic: interrupt-controller@d000 {
+				compatible = "arm,cortex-a9-gic";
+				#interrupt-cells = <3>;
+				#size-cells = <0>;
+				interrupt-controller;
+				reg = <0xd000 0x1000>,
+				      <0xc100 0x100>;
+			};
+
+			spi0: spi@10600 {
+				compatible = "marvell,orion-spi";
+				reg = <0x10600 0x50>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				cell-index = <0>;
+				interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			spi1: spi@10680 {
+				compatible = "marvell,orion-spi";
+				reg = <0x10680 0x50>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				cell-index = <1>;
+				interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@11000 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11000 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@11100 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11100 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			serial@12000 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12000 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				status = "disabled";
+			};
+
+			serial@12100 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12100 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				status = "disabled";
+			};
+
+			pinctrl {
+				compatible = "marvell,mv88f6720-pinctrl";
+				reg = <0x18000 0x24>;
+
+				i2c0_pins: i2c0-pins {
+					marvell,pins = "mpp14",  "mpp15";
+					marvell,function = "i2c0";
+				};
+
+				i2c1_pins: i2c1-pins {
+					marvell,pins = "mpp61",  "mpp62";
+					marvell,function = "i2c1";
+				};
+
+				nand_pins: nand-pins {
+					marvell,pins = "mpp0", "mpp1", "mpp2",
+						"mpp3", "mpp4", "mpp5",
+						"mpp6", "mpp7", "mpp8",
+						"mpp9", "mpp10", "mpp11",
+						"mpp12", "mpp13";
+					marvell,function = "nand";
+				};
+
+				sdio_pins: sdio-pins {
+					marvell,pins = "mpp24",  "mpp25", "mpp26",
+						     "mpp27", "mpp28", "mpp29";
+					marvell,function = "sd";
+				};
+
+				spi0_pins: spi0-pins {
+					marvell,pins = "mpp0",  "mpp1", "mpp4",
+						     "mpp5", "mpp8", "mpp9";
+					marvell,function = "spi0";
+				};
+			};
+
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			gpio1: gpio@18140 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18140 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			gpio2: gpio@18180 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18180 0x40>;
+				ngpios = <3>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			system-controller@18200 {
+				compatible = "marvell,armada-375-system-controller";
+				reg = <0x18200 0x100>;
+			};
+
+			gateclk: clock-gating-control@18220 {
+				compatible = "marvell,armada-375-gating-clock";
+				reg = <0x18220 0x4>;
+				clocks = <&coreclk 0>;
+				#clock-cells = <1>;
+			};
+
+			mbusc: mbus-controller@20000 {
+				compatible = "marvell,mbus-controller";
+				reg = <0x20000 0x100>, <0x20180 0x20>;
+			};
+
+			mpic: interrupt-controller@20000 {
+				compatible = "marvell,mpic";
+				reg = <0x20a00 0x2d0>, <0x21070 0x58>;
+				#interrupt-cells = <1>;
+				#size-cells = <1>;
+				interrupt-controller;
+				msi-controller;
+				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			timer@20300 {
+				compatible = "marvell,armada-375-timer", "marvell,armada-370-timer";
+				reg = <0x20300 0x30>, <0x21040 0x30>;
+				interrupts-extended = <&gic  GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+						      <&mpic 5>,
+						      <&mpic 6>;
+				clocks = <&coreclk 0>;
+			};
+
+			xor@60800 {
+				compatible = "marvell,orion-xor";
+				reg = <0x60800 0x100
+				       0x60A00 0x100>;
+				clocks = <&gateclk 22>;
+				status = "okay";
+
+				xor00 {
+					interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor01 {
+					interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
+			};
+
+			xor@60900 {
+				compatible = "marvell,orion-xor";
+				reg = <0x60900 0x100
+				       0x60b00 0x100>;
+				clocks = <&gateclk 23>;
+				status = "okay";
+
+				xor10 {
+					interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor11 {
+					interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
+			};
+
+			sata@a0000 {
+				compatible = "marvell,orion-sata";
+				reg = <0xa0000 0x5000>;
+				interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 14>, <&gateclk 20>;
+				clock-names = "0", "1";
+				status = "disabled";
+			};
+
+			nand@d0000 {
+				compatible = "marvell,armada370-nand";
+				reg = <0xd0000 0x54>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 11>;
+				status = "disabled";
+			};
+
+			mvsdio@d4000 {
+				compatible = "marvell,orion-sdio";
+				reg = <0xd4000 0x200>;
+				interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 17>;
+				bus-width = <4>;
+				cap-sdio-irq;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				status = "disabled";
+			};
+
+			coreclk: mvebu-sar@e8204 {
+				compatible = "marvell,armada-375-core-clock";
+				reg = <0xe8204 0x04>;
+				#clock-cells = <1>;
+			};
+
+			coredivclk: corediv-clock@e8250 {
+				compatible = "marvell,armada-375-corediv-clock";
+				reg = <0xe8250 0xc>;
+				#clock-cells = <1>;
+				clocks = <&mainpll>;
+				clock-output-names = "nand";
+			};
+		};
+
+		pcie-controller {
+			compatible = "marvell,armada-370-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			msi-parent = <&mpic>;
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
+				0x82000000 0x1 0       MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0 MEM */
+				0x81000000 0x1 0       MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0 IO  */
+				0x82000000 0x2 0       MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 1 MEM */
+				0x81000000 0x2 0       MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 1 IO  */>;
+
+			pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			pcie@2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <1>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+
+		};
+	};
+};

arch/arm/boot/dts/armada-380.dtsi

@@ -0,0 +1,117 @@
+/*
+ * Device Tree Include file for Marvell Armada 380 SoC.
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include "armada-38x.dtsi"
+
+/ {
+	model = "Marvell Armada 380 family SoC";
+	compatible = "marvell,armada380", "marvell,armada38x";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+		};
+	};
+
+	soc {
+		internal-regs {
+			pinctrl {
+				compatible = "marvell,mv88f6810-pinctrl";
+				reg = <0x18000 0x20>;
+			};
+		};
+
+		pcie-controller {
+			compatible = "marvell,armada-370-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			msi-parent = <&mpic>;
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
+				0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
+				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
+				0x82000000 0x1 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
+				0x81000000 0x1 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO  */
+				0x82000000 0x2 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */
+				0x81000000 0x2 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO  */
+				0x82000000 0x3 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */
+				0x81000000 0x3 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO  */>;
+
+			/* x1 port */
+			pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 8>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie@2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie@3,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
+					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <2>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+		};
+	};
+};

arch/arm/boot/dts/armada-385-db.dts

@@ -0,0 +1,122 @@
+/*
+ * Device Tree file for Marvell Armada 385 evaluation board
+ * (DB-88F6820)
+ *
+ *  Copyright (C) 2014 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "armada-385.dtsi"
+
+/ {
+	model = "Marvell Armada 385 Development Board";
+	compatible = "marvell,a385-db", "marvell,armada385", "marvell,armada38x";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>; /* 256 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+			spi@10600 {
+				status = "okay";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "w25q32";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <108000000>;
+				};
+			};
+
+			i2c@11000 {
+				status = "okay";
+				clock-frequency = <100000>;
+			};
+
+			i2c@11100 {
+				status = "okay";
+				clock-frequency = <100000>;
+			};
+
+			serial@12000 {
+				clock-frequency = <200000000>;
+				status = "okay";
+			};
+
+			ethernet@30000 {
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "rgmii-id";
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "rgmii-id";
+			};
+
+			mdio {
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+
+			flash@d0000 {
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+
+				partition@0 {
+					label = "U-Boot";
+					reg = <0 0x800000>;
+				};
+				partition@800000 {
+					label = "Linux";
+					reg = <0x800000 0x800000>;
+				};
+				partition@1000000 {
+					label = "Filesystem";
+					reg = <0x1000000 0x3f000000>;
+				};
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+			/*
+			 * The two PCIe units are accessible through
+			 * standard PCIe slots on the board.
+			 */
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+			pcie@2,0 {
+				/* Port 1, Lane 0 */
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/armada-385-rd.dts

@@ -0,0 +1,94 @@
+/*
+ * Device Tree file for Marvell Armada 385 Reference Design board
+ * (RD-88F6820-AP)
+ *
+ *  Copyright (C) 2014 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "armada-385.dtsi"
+
+/ {
+	model = "Marvell Armada 385 Reference Design";
+	compatible = "marvell,a385-rd", "marvell,armada385", "marvell,armada38x";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>; /* 256 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+			spi@10600 {
+				status = "okay";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "st,m25p128";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <108000000>;
+				};
+			};
+
+			i2c@11000 {
+				status = "okay";
+				clock-frequency = <100000>;
+			};
+
+			serial@12000 {
+				clock-frequency = <200000000>;
+				status = "okay";
+			};
+
+			ethernet@30000 {
+				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "rgmii-id";
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "rgmii-id";
+			};
+
+
+			mdio {
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+			/*
+			 * One PCIe units is accessible through
+			 * standard PCIe slot on the board.
+			 */
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/armada-385.dtsi

@@ -0,0 +1,149 @@
+/*
+ * Device Tree Include file for Marvell Armada 385 SoC.
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include "armada-38x.dtsi"
+
+/ {
+	model = "Marvell Armada 385 family SoC";
+	compatible = "marvell,armada385", "marvell,armada38x";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+		};
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <1>;
+		};
+	};
+
+	soc {
+		internal-regs {
+			pinctrl {
+				compatible = "marvell,mv88f6820-pinctrl";
+				reg = <0x18000 0x20>;
+			};
+		};
+
+		pcie-controller {
+			compatible = "marvell,armada-370-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			msi-parent = <&mpic>;
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
+				0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
+				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
+				0x82000000 0x1 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
+				0x81000000 0x1 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO  */
+				0x82000000 0x2 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */
+				0x81000000 0x2 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO  */
+				0x82000000 0x3 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */
+				0x81000000 0x3 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO  */
+				0x82000000 0x4 0     MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */
+				0x81000000 0x4 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO  */>;
+
+			/*
+			 * This port can be either x4 or x1. When
+			 * configured in x4 by the bootloader, then
+			 * pcie@4,0 is not available.
+			 */
+			pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 8>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie@2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie@3,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
+					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <2>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+
+			/*
+			 * x1 port only available when pcie@1,0 is
+			 * configured as a x1 port
+			 */
+			pcie@4,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
+					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <3>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 7>;
+				status = "disabled";
+			};
+		};
+	};
+};

arch/arm/boot/dts/armada-38x.dtsi

@@ -0,0 +1,376 @@
+/*
+ * Device Tree Include file for Marvell Armada 38x family of SoCs.
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
+/ {
+	model = "Marvell Armada 38x family SoC";
+	compatible = "marvell,armada38x";
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		eth0 = &eth0;
+		eth1 = &eth1;
+		eth2 = &eth2;
+	};
+
+	soc {
+		compatible = "marvell,armada380-mbus", "marvell,armada370-mbus",
+			     "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		controller = <&mbusc>;
+		interrupt-parent = <&gic>;
+		pcie-mem-aperture = <0xe0000000 0x8000000>;
+		pcie-io-aperture  = <0xe8000000 0x100000>;
+
+		bootrom {
+			compatible = "marvell,bootrom";
+			reg = <MBUS_ID(0x01, 0x1d) 0 0x200000>;
+		};
+
+		devbus-bootcs {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10400 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x2f) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs0 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10408 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3e) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs1 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10410 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3d) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs2 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10418 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3b) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs3 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10420 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x37) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		internal-regs {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
+
+			L2: cache-controller@8000 {
+				compatible = "arm,pl310-cache";
+				reg = <0x8000 0x1000>;
+				cache-unified;
+				cache-level = <2>;
+			};
+
+			timer@c600 {
+				compatible = "arm,cortex-a9-twd-timer";
+				reg = <0xc600 0x20>;
+				interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>;
+				clocks = <&coreclk 2>;
+			};
+
+			gic: interrupt-controller@d000 {
+				compatible = "arm,cortex-a9-gic";
+				#interrupt-cells = <3>;
+				#size-cells = <0>;
+				interrupt-controller;
+				reg = <0xd000 0x1000>,
+				      <0xc100 0x100>;
+			};
+
+			spi0: spi@10600 {
+				compatible = "marvell,orion-spi";
+				reg = <0x10600 0x50>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				cell-index = <0>;
+				interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			spi1: spi@10680 {
+				compatible = "marvell,orion-spi";
+				reg = <0x10680 0x50>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				cell-index = <1>;
+				interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@11000 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11000 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@11100 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11100 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			serial@12000 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12000 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				status = "disabled";
+			};
+
+			serial@12100 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12100 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				status = "disabled";
+			};
+
+			pinctrl {
+				compatible = "marvell,mv88f6820-pinctrl";
+				reg = <0x18000 0x20>;
+			};
+
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			gpio1: gpio@18140 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18140 0x40>;
+				ngpios = <28>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			system-controller@18200 {
+				compatible = "marvell,armada-380-system-controller",
+					     "marvell,armada-370-xp-system-controller";
+				reg = <0x18200 0x100>;
+			};
+
+			gateclk: clock-gating-control@18220 {
+				compatible = "marvell,armada-380-gating-clock";
+				reg = <0x18220 0x4>;
+				clocks = <&coreclk 0>;
+				#clock-cells = <1>;
+			};
+
+			coreclk: mvebu-sar@18600 {
+				compatible = "marvell,armada-380-core-clock";
+				reg = <0x18600 0x04>;
+				#clock-cells = <1>;
+			};
+
+			mbusc: mbus-controller@20000 {
+				compatible = "marvell,mbus-controller";
+				reg = <0x20000 0x100>, <0x20180 0x20>;
+			};
+
+			mpic: interrupt-controller@20000 {
+				compatible = "marvell,mpic";
+				reg = <0x20a00 0x2d0>, <0x21070 0x58>;
+				#interrupt-cells = <1>;
+				#size-cells = <1>;
+				interrupt-controller;
+				msi-controller;
+				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			timer@20300 {
+				compatible = "marvell,armada-380-timer",
+					     "marvell,armada-xp-timer";
+				reg = <0x20300 0x30>, <0x21040 0x30>;
+				interrupts-extended = <&gic  GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+						      <&mpic 5>,
+						      <&mpic 6>;
+				clocks = <&coreclk 2>, <&refclk>;
+				clock-names = "nbclk", "fixed";
+			};
+
+			eth1: ethernet@30000 {
+				compatible = "marvell,armada-370-neta";
+				reg = <0x30000 0x4000>;
+				interrupts-extended = <&mpic 10>;
+				clocks = <&gateclk 3>;
+				status = "disabled";
+			};
+
+			eth2: ethernet@34000 {
+				compatible = "marvell,armada-370-neta";
+				reg = <0x34000 0x4000>;
+				interrupts-extended = <&mpic 12>;
+				clocks = <&gateclk 2>;
+				status = "disabled";
+			};
+
+			xor@60800 {
+				compatible = "marvell,orion-xor";
+				reg = <0x60800 0x100
+				       0x60a00 0x100>;
+				clocks = <&gateclk 22>;
+				status = "okay";
+
+				xor00 {
+					interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor01 {
+					interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
+			};
+
+			xor@60900 {
+				compatible = "marvell,orion-xor";
+				reg = <0x60900 0x100
+				       0x60b00 0x100>;
+				clocks = <&gateclk 28>;
+				status = "okay";
+
+				xor10 {
+					interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor11 {
+					interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
+			};
+
+			eth0: ethernet@70000 {
+				compatible = "marvell,armada-370-neta";
+				reg = <0x70000 0x4000>;
+				interrupts-extended = <&mpic 8>;
+				clocks = <&gateclk 4>;
+				status = "disabled";
+			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "marvell,orion-mdio";
+				reg = <0x72004 0x4>;
+			};
+
+			coredivclk: clock@e4250 {
+				compatible = "marvell,armada-380-corediv-clock";
+				reg = <0xe4250 0xc>;
+				#clock-cells = <1>;
+				clocks = <&mainpll>;
+				clock-output-names = "nand";
+			};
+
+			flash@d0000 {
+				compatible = "marvell,armada370-nand";
+				reg = <0xd0000 0x54>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&coredivclk 0>;
+				status = "disabled";
+			};
+		};
+	};
+
+	clocks {
+		/* 2 GHz fixed main PLL */
+		mainpll: mainpll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <2000000000>;
+		};
+
+		/* 25 MHz reference crystal */
+		refclk: oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <25000000>;
+		};
+	};
+};

arch/arm/boot/dts/armada-xp-axpwifiap.dts

@@ -16,6 +16,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include "armada-xp-mv78230.dtsi"
 
 / {
@@ -157,8 +159,8 @@
 
 		button@1 {
 			label = "Factory Reset Button";
-			linux,code = <141>; /* KEY_SETUP */
-			gpios = <&gpio1 1 1>;
+			linux,code = <KEY_SETUP>;
+			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
 		};
 	};
 };

arch/arm/boot/dts/armada-xp-db.dts

@@ -2,7 +2,7 @@
  * Device Tree file for Marvell Armada XP evaluation board
  * (DB-78460-BP)
  *
- * Copyright (C) 2012 Marvell
+ * Copyright (C) 2012-2014 Marvell
  *
  * Lior Amsalem <alior@marvell.com>
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
@@ -11,6 +11,15 @@
  * This file is licensed under the terms of the GNU General Public
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
+  *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
  */
 
 /dts-v1/;
@@ -30,7 +39,7 @@
 	};
 
 	soc {
-		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
 			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
 			  MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>;
 

arch/arm/boot/dts/armada-xp-gp.dts

@@ -2,7 +2,7 @@
  * Device Tree file for Marvell Armada XP development board
  * (DB-MV784MP-GP)
  *
- * Copyright (C) 2013 Marvell
+ * Copyright (C) 2013-2014 Marvell
  *
  * Lior Amsalem <alior@marvell.com>
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
@@ -11,6 +11,15 @@
  * This file is licensed under the terms of the GNU General Public
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
  */
 
 /dts-v1/;
@@ -30,16 +39,17 @@
                  * 8 GB of plug-in RAM modules by default.The amount
                  * of memory available can be changed by the
                  * bootloader according the size of the module
-                 * actually plugged. Only 7GB are usable because
-                 * addresses from 0xC0000000 to 0xffffffff are used by
-                 * the internal registers of the SoC.
+                 * actually plugged. However, memory between
+                 * 0xF0000000 to 0xFFFFFFFF cannot be used, as it is
+                 * the address range used for I/O (internal registers,
+                 * MBus windows).
 		 */
-		reg = <0x00000000 0x00000000 0x00000000 0xC0000000>,
+		reg = <0x00000000 0x00000000 0x00000000 0xf0000000>,
 		      <0x00000001 0x00000000 0x00000001 0x00000000>;
 	};
 
 	soc {
-		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
 			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
 			  MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>;
 

arch/arm/boot/dts/armada-xp-matrix.dts

@@ -23,7 +23,12 @@
 
 	memory {
 		device_type = "memory";
-		reg = <0 0x00000000 0 0x80000000>; /* 2 GB */
+		/*
+		 * This board has 4 GB of RAM, but the last 256 MB of
+		 * RAM are not usable due to the overlap with the MBus
+		 * Window address range
+		 */
+		reg = <0 0x00000000 0 0xf0000000>;
 	};
 
 	soc {

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts

@@ -11,6 +11,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include "armada-xp-mv78260.dtsi"
 
 / {
@@ -90,19 +92,19 @@
 
 				red_led {
 					label = "red_led";
-					gpios = <&gpio1 17 1>;
+					gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 					default-state = "off";
 				};
 
 				yellow_led {
 					label = "yellow_led";
-					gpios = <&gpio1 19 1>;
+					gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
 					default-state = "off";
 				};
 
 				green_led {
 					label = "green_led";
-					gpios = <&gpio1 21 1>;
+					gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
 					default-state = "keep";
 				};
 			};
@@ -114,8 +116,8 @@
 
 				button@1 {
 					label = "Init Button";
-					linux,code = <116>;
-					gpios = <&gpio1 28 0>;
+					linux,code = <KEY_POWER>;
+					gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
 				};
 			};
 

arch/arm/boot/dts/armada-xp.dtsi

@@ -111,6 +111,12 @@
 				clock-names = "nbclk", "fixed";
 			};
 
+			watchdog@20300 {
+				compatible = "marvell,armada-xp-wdt";
+				clocks = <&coreclk 2>, <&refclk>;
+				clock-names = "nbclk", "fixed";
+			};
+
 			armada-370-xp-pmsu@22000 {
 				compatible = "marvell,armada-370-xp-pmsu";
 				reg = <0x22100 0x400>, <0x20800 0x20>;

arch/arm/boot/dts/at91-ariag25.dts

@@ -129,7 +129,6 @@
 			adc0: adc@f804c000 {
 				status = "okay";
 				atmel,adc-channels-used = <0xf>;
-				atmel,adc-num-channels = <4>;
 			};
 
 			dbgu: serial@fffff200 {

arch/arm/boot/dts/at91-cosino.dtsi

@@ -64,7 +64,6 @@
 			};
 
 			adc0: adc@f804c000 {
-				atmel,adc-clock-rate = <1000000>;
 				atmel,adc-ts-wires = <4>;
 				atmel,adc-ts-pressure-threshold = <10000>;
 				status = "okay";

arch/arm/boot/dts/at91-cosino_mega2560.dts

@@ -27,7 +27,6 @@
 			};
 
 			adc0: adc@f804c000 {
-				atmel,adc-clock-rate = <1000000>;
 				atmel,adc-ts-wires = <4>;
 				atmel,adc-ts-pressure-threshold = <10000>;
 				status = "okay";

arch/arm/boot/dts/at91sam9260.dtsi

@@ -608,37 +608,38 @@
 			};
 
 			adc0: adc@fffe0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				compatible = "atmel,at91sam9260-adc";
 				reg = <0xfffe0000 0x100>;
 				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 0>;
 				atmel,adc-use-external-triggers;
 				atmel,adc-channels-used = <0xf>;
 				atmel,adc-vref = <3300>;
-				atmel,adc-num-channels = <4>;
 				atmel,adc-startup-time = <15>;
-				atmel,adc-channel-base = <0x30>;
-				atmel,adc-drdy-mask = <0x10000>;
-				atmel,adc-status-register = <0x1c>;
-				atmel,adc-trigger-register = <0x04>;
 				atmel,adc-res = <8 10>;
 				atmel,adc-res-names = "lowres", "highres";
 				atmel,adc-use-res = "highres";
 
 				trigger@0 {
+					reg = <0>;
 					trigger-name = "timer-counter-0";
 					trigger-value = <0x1>;
 				};
 				trigger@1 {
+					reg = <1>;
 					trigger-name = "timer-counter-1";
 					trigger-value = <0x3>;
 				};
 
 				trigger@2 {
+					reg = <2>;
 					trigger-name = "timer-counter-2";
 					trigger-value = <0x5>;
 				};
 
 				trigger@3 {
+					reg = <3>;
 					trigger-name = "external";
 					trigger-value = <0x13>;
 					trigger-external;

arch/arm/boot/dts/at91sam9g45.dtsi

@@ -632,40 +632,41 @@
 			};
 
 			adc0: adc@fffb0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				compatible = "atmel,at91sam9260-adc";
 				reg = <0xfffb0000 0x100>;
 				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
 				atmel,adc-use-external-triggers;
 				atmel,adc-channels-used = <0xff>;
 				atmel,adc-vref = <3300>;
-				atmel,adc-num-channels = <8>;
 				atmel,adc-startup-time = <40>;
-				atmel,adc-channel-base = <0x30>;
-				atmel,adc-drdy-mask = <0x10000>;
-				atmel,adc-status-register = <0x1c>;
-				atmel,adc-trigger-register = <0x08>;
 				atmel,adc-res = <8 10>;
 				atmel,adc-res-names = "lowres", "highres";
 				atmel,adc-use-res = "highres";
 
 				trigger@0 {
+					reg = <0>;
 					trigger-name = "external-rising";
 					trigger-value = <0x1>;
 					trigger-external;
 				};
 				trigger@1 {
+					reg = <1>;
 					trigger-name = "external-falling";
 					trigger-value = <0x2>;
 					trigger-external;
 				};
 
 				trigger@2 {
+					reg = <2>;
 					trigger-name = "external-any";
 					trigger-value = <0x3>;
 					trigger-external;
 				};
 
 				trigger@3 {
+					reg = <3>;
 					trigger-name = "continuous";
 					trigger-value = <0x6>;
 				};
@@ -817,6 +818,7 @@
 			      >;
 			atmel,nand-addr-offset = <21>;
 			atmel,nand-cmd-offset = <22>;
+			atmel,nand-has-dma;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			gpios = <&pioC 8 GPIO_ACTIVE_HIGH

arch/arm/boot/dts/at91sam9n12.dtsi

@@ -570,6 +570,7 @@
 			atmel,pmecc-lookup-table-offset = <0x0 0x8000>;
 			atmel,nand-addr-offset = <21>;
 			atmel,nand-cmd-offset = <22>;
+			atmel,nand-has-dma;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			gpios = <&pioD 5 GPIO_ACTIVE_HIGH

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -621,41 +621,42 @@
 			};
 
 			adc0: adc@f804c000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				compatible = "atmel,at91sam9260-adc";
 				reg = <0xf804c000 0x100>;
 				interrupts = <19 IRQ_TYPE_LEVEL_HIGH 0>;
-				atmel,adc-use-external;
+				atmel,adc-use-external-triggers;
 				atmel,adc-channels-used = <0xffff>;
 				atmel,adc-vref = <3300>;
-				atmel,adc-num-channels = <12>;
 				atmel,adc-startup-time = <40>;
-				atmel,adc-channel-base = <0x50>;
-				atmel,adc-drdy-mask = <0x1000000>;
-				atmel,adc-status-register = <0x30>;
-				atmel,adc-trigger-register = <0xc0>;
 				atmel,adc-res = <8 10>;
 				atmel,adc-res-names = "lowres", "highres";
 				atmel,adc-use-res = "highres";
 
 				trigger@0 {
+					reg = <0>;
 					trigger-name = "external-rising";
 					trigger-value = <0x1>;
 					trigger-external;
 				};
 
 				trigger@1 {
+					reg = <1>;
 					trigger-name = "external-falling";
 					trigger-value = <0x2>;
 					trigger-external;
 				};
 
 				trigger@2 {
+					reg = <2>;
 					trigger-name = "external-any";
 					trigger-value = <0x3>;
 					trigger-external;
 				};
 
 				trigger@3 {
+					reg = <3>;
 					trigger-name = "continuous";
 					trigger-value = <0x6>;
 				};
@@ -790,6 +791,7 @@
 			atmel,pmecc-lookup-table-offset = <0x0 0x8000>;
 			atmel,nand-addr-offset = <21>;
 			atmel,nand-cmd-offset = <22>;
+			atmel,nand-has-dma;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			gpios = <&pioD 5 GPIO_ACTIVE_HIGH

arch/arm/boot/dts/bcm11351.dtsi

@@ -14,6 +14,8 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
+#include "dt-bindings/clock/bcm281xx.h"
+
 #include "skeleton.dtsi"
 
 / {
@@ -43,7 +45,7 @@
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
 		status = "disabled";
 		reg = <0x3e000000 0x1000>;
-		clocks = <&uartb_clk>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB>;
 		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
@@ -53,7 +55,7 @@
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
 		status = "disabled";
 		reg = <0x3e001000 0x1000>;
-		clocks = <&uartb2_clk>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB2>;
 		interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
@@ -63,7 +65,7 @@
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
 		status = "disabled";
 		reg = <0x3e002000 0x1000>;
-		clocks = <&uartb3_clk>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB3>;
 		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
@@ -73,7 +75,7 @@
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
 		status = "disabled";
 		reg = <0x3e003000 0x1000>;
-		clocks = <&uartb4_clk>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB4>;
 		interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
@@ -95,7 +97,7 @@
 		compatible = "brcm,kona-timer";
 		reg = <0x35006000 0x1000>;
 		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&hub_timer_clk>;
+		clocks = <&aon_ccu BCM281XX_AON_CCU_HUB_TIMER>;
 	};
 
 	gpio: gpio@35003000 {
@@ -118,7 +120,7 @@
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f180000 0x10000>;
 		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&sdio1_clk>;
+		clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO1>;
 		status = "disabled";
 	};
 
@@ -126,7 +128,7 @@
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f190000 0x10000>;
 		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&sdio2_clk>;
+		clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO2>;
 		status = "disabled";
 	};
 
@@ -134,7 +136,7 @@
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f1a0000 0x10000>;
 		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&sdio3_clk>;
+		clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO3>;
 		status = "disabled";
 	};
 
@@ -142,7 +144,7 @@
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f1b0000 0x10000>;
 		interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&sdio4_clk>;
+		clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO4>;
 		status = "disabled";
 	};
 
@@ -157,7 +159,7 @@
 		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bsc1_clk>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_BSC1>;
 		status = "disabled";
 	};
 
@@ -167,7 +169,7 @@
 		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bsc2_clk>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_BSC2>;
 		status = "disabled";
 	};
 
@@ -177,7 +179,7 @@
 		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bsc3_clk>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_BSC3>;
 		status = "disabled";
 	};
 
@@ -187,105 +189,191 @@
 		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&pmu_bsc_clk>;
+		clocks = <&aon_ccu BCM281XX_AON_CCU_PMU_BSC>;
 		status = "disabled";
 	};
 
 	clocks {
-		bsc1_clk: bsc1 {
-			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		root_ccu: root_ccu {
+			compatible = "brcm,bcm11351-root-ccu";
+			reg = <0x35001000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "frac_1m";
+		};
+
+		hub_ccu: hub_ccu {
+			compatible = "brcm,bcm11351-hub-ccu";
+			reg = <0x34000000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "tmon_1m";
+		};
+
+		aon_ccu: aon_ccu {
+			compatible = "brcm,bcm11351-aon-ccu";
+			reg = <0x35002000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "hub_timer",
+					     "pmu_bsc",
+					     "pmu_bsc_var";
+		};
+
+		master_ccu: master_ccu {
+			compatible = "brcm,bcm11351-master-ccu";
+			reg = <0x3f001000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "sdio1",
+					     "sdio2",
+					     "sdio3",
+					     "sdio4",
+					     "usb_ic",
+					     "hsic2_48m",
+					     "hsic2_12m";
+		};
+
+		slave_ccu: slave_ccu {
+			compatible = "brcm,bcm11351-slave-ccu";
+			reg = <0x3e011000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "uartb",
+					     "uartb2",
+					     "uartb3",
+					     "uartb4",
+					     "ssp0",
+					     "ssp2",
+					     "bsc1",
+					     "bsc2",
+					     "bsc3",
+					     "pwm";
+		};
+
+		ref_1m_clk: ref_1m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <1000000>;
 		};
 
-		bsc2_clk: bsc2 {
+		ref_32k_clk: ref_32k {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
+			clock-frequency = <32768>;
+		};
+
+		bbl_32k_clk: bbl_32k {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
 		};
 
-		bsc3_clk: bsc3 {
+		ref_13m_clk: ref_13m {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <13000000>;
-			#clock-cells = <0>;
 		};
 
-		pmu_bsc_clk: pmu_bsc {
+		var_13m_clk: var_13m {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <13000000>;
-			#clock-cells = <0>;
 		};
 
-		hub_timer_clk: hub_timer {
-			compatible = "fixed-clock";
-			clock-frequency = <32768>;
+		dft_19_5m_clk: dft_19_5m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <19500000>;
 		};
 
-		pwm_clk: pwm {
+		ref_crystal_clk: ref_crystal {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <26000000>;
-			#clock-cells = <0>;
 		};
 
-		sdio1_clk: sdio1 {
-			compatible = "fixed-clock";
-			clock-frequency = <48000000>;
+		ref_cx40_clk: ref_cx40 {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <40000000>;
 		};
 
-		sdio2_clk: sdio2 {
-			compatible = "fixed-clock";
-			clock-frequency = <48000000>;
+		ref_52m_clk: ref_52m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
 		};
 
-		sdio3_clk: sdio3 {
-			compatible = "fixed-clock";
-			clock-frequency = <48000000>;
+		var_52m_clk: var_52m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
 		};
 
-		sdio4_clk: sdio4 {
+		usb_otg_ahb_clk: usb_otg_ahb {
 			compatible = "fixed-clock";
-			clock-frequency = <48000000>;
+			clock-frequency = <52000000>;
 			#clock-cells = <0>;
 		};
 
-		tmon_1m_clk: tmon_1m {
-			compatible = "fixed-clock";
-			clock-frequency = <1000000>;
+		ref_96m_clk: ref_96m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <96000000>;
 		};
 
-		uartb_clk: uartb {
-			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
+		var_96m_clk: var_96m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <96000000>;
 		};
 
-		uartb2_clk: uartb2 {
+		ref_104m_clk: ref_104m {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
+			clock-frequency = <104000000>;
+		};
+
+		var_104m_clk: var_104m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <104000000>;
 		};
 
-		uartb3_clk: uartb3 {
+		ref_156m_clk: ref_156m {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
+			clock-frequency = <156000000>;
+		};
+
+		var_156m_clk: var_156m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <156000000>;
 		};
 
-		uartb4_clk: uartb4 {
+		ref_208m_clk: ref_208m {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
+			clock-frequency = <208000000>;
+		};
+
+		var_208m_clk: var_208m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <208000000>;
 		};
 
-		usb_otg_ahb_clk: usb_otg_ahb {
+		ref_312m_clk: ref_312m {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
-			clock-frequency = <52000000>;
+			clock-frequency = <312000000>;
+		};
+
+		var_312m_clk: var_312m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <312000000>;
 		};
 	};
 

arch/arm/boot/dts/bcm11351-brt.dts → arch/arm/boot/dts/bcm21664-garnet.dts

@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2012 Broadcom Corporation
+ * Copyright (C) 2014 Broadcom Corporation
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
@@ -13,11 +13,13 @@
 
 /dts-v1/;
 
-#include "bcm11351.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+#include "bcm21664.dtsi"
 
 / {
-	model = "BCM11351 BRT board";
-	compatible = "brcm,bcm11351-brt", "brcm,bcm11351";
+	model = "BCM21664 Garnet board";
+	compatible = "brcm,bcm21664-garnet", "brcm,bcm21664";
 
 	memory {
 		reg = <0x80000000 0x40000000>; /* 1 GB */
@@ -40,7 +42,7 @@
 
 	sdio4: sdio@3f1b0000 {
 		max-frequency = <48000000>;
-		cd-gpios = <&gpio 14 0>;
+		cd-gpios = <&gpio 91 GPIO_ACTIVE_LOW>;
 		status = "okay";
 	};
 

arch/arm/boot/dts/bcm21664.dtsi

@@ -0,0 +1,292 @@
+/*
+ * Copyright (C) 2014 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#include "skeleton.dtsi"
+
+/ {
+	model = "BCM21664 SoC";
+	compatible = "brcm,bcm21664";
+	interrupt-parent = <&gic>;
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	gic: interrupt-controller@3ff00100 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+		interrupt-controller;
+		reg = <0x3ff01000 0x1000>,
+		      <0x3ff00100 0x100>;
+	};
+
+	smc@0x3404e000 {
+		compatible = "brcm,bcm21664-smc", "brcm,kona-smc";
+		reg = <0x3404e000 0x400>; /* 1 KiB in SRAM */
+	};
+
+	uart@3e000000 {
+		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
+		status = "disabled";
+		reg = <0x3e000000 0x118>;
+		clocks = <&uartb_clk>;
+		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+	};
+
+	uart@3e001000 {
+		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
+		status = "disabled";
+		reg = <0x3e001000 0x118>;
+		clocks = <&uartb2_clk>;
+		interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+	};
+
+	uart@3e002000 {
+		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
+		status = "disabled";
+		reg = <0x3e002000 0x118>;
+		clocks = <&uartb3_clk>;
+		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+	};
+
+	L2: l2-cache {
+		compatible = "arm,pl310-cache";
+		reg = <0x3ff20000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+	};
+
+	brcm,resetmgr@35001f00 {
+		compatible = "brcm,bcm21664-resetmgr";
+		reg = <0x35001f00 0x24>;
+	};
+
+	timer@35006000 {
+		compatible = "brcm,kona-timer";
+		reg = <0x35006000 0x1c>;
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&hub_timer_clk>;
+	};
+
+	gpio: gpio@35003000 {
+		compatible = "brcm,bcm21664-gpio", "brcm,kona-gpio";
+		reg = <0x35003000 0x524>;
+		interrupts =
+		       <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+	};
+
+	sdio1: sdio@3f180000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f180000 0x801c>;
+		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&sdio1_clk>;
+		status = "disabled";
+	};
+
+	sdio2: sdio@3f190000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f190000 0x801c>;
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&sdio2_clk>;
+		status = "disabled";
+	};
+
+	sdio3: sdio@3f1a0000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f1a0000 0x801c>;
+		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&sdio3_clk>;
+		status = "disabled";
+	};
+
+	sdio4: sdio@3f1b0000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f1b0000 0x801c>;
+		interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&sdio4_clk>;
+		status = "disabled";
+	};
+
+	i2c@3e016000 {
+		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+		reg = <0x3e016000 0x70>;
+		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bsc1_clk>;
+		status = "disabled";
+	};
+
+	i2c@3e017000 {
+		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+		reg = <0x3e017000 0x70>;
+		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bsc2_clk>;
+		status = "disabled";
+	};
+
+	i2c@3e018000 {
+		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+		reg = <0x3e018000 0x70>;
+		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bsc3_clk>;
+		status = "disabled";
+	};
+
+	i2c@3e01c000 {
+		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+		reg = <0x3e01c000 0x70>;
+		interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bsc4_clk>;
+		status = "disabled";
+	};
+
+	clocks {
+		bsc1_clk: bsc1 {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		bsc2_clk: bsc2 {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		bsc3_clk: bsc3 {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		bsc4_clk: bsc4 {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		pmu_bsc_clk: pmu_bsc {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		hub_timer_clk: hub_timer {
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			#clock-cells = <0>;
+		};
+
+		pwm_clk: pwm {
+			compatible = "fixed-clock";
+			clock-frequency = <26000000>;
+			#clock-cells = <0>;
+		};
+
+		sdio1_clk: sdio1 {
+			compatible = "fixed-clock";
+			clock-frequency = <48000000>;
+			#clock-cells = <0>;
+		};
+
+		sdio2_clk: sdio2 {
+			compatible = "fixed-clock";
+			clock-frequency = <48000000>;
+			#clock-cells = <0>;
+		};
+
+		sdio3_clk: sdio3 {
+			compatible = "fixed-clock";
+			clock-frequency = <48000000>;
+			#clock-cells = <0>;
+		};
+
+		sdio4_clk: sdio4 {
+			compatible = "fixed-clock";
+			clock-frequency = <48000000>;
+			#clock-cells = <0>;
+		};
+
+		tmon_1m_clk: tmon_1m {
+			compatible = "fixed-clock";
+			clock-frequency = <1000000>;
+			#clock-cells = <0>;
+		};
+
+		uartb_clk: uartb {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		uartb2_clk: uartb2 {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		uartb3_clk: uartb3 {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		usb_otg_ahb_clk: usb_otg_ahb {
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
+			#clock-cells = <0>;
+		};
+	};
+
+	usbotg: usb@3f120000 {
+		compatible = "snps,dwc2";
+		reg = <0x3f120000 0x10000>;
+		interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&usb_otg_ahb_clk>;
+		clock-names = "otg";
+		phys = <&usbphy>;
+		phy-names = "usb2-phy";
+		status = "disabled";
+	};
+
+	usbphy: usb-phy@3f130000 {
+		compatible = "brcm,kona-usb2-phy";
+		reg = <0x3f130000 0x28>;
+		#phy-cells = <0>;
+		status = "disabled";
+	};
+};

arch/arm/boot/dts/bcm28155-ap.dts

@@ -46,27 +46,32 @@
 
 	i2c@3500d000 {
 		status="okay";
-		clock-frequency = <400000>;
-	};
+		clock-frequency = <100000>;
 
-	sdio1: sdio@3f180000 {
-		max-frequency = <48000000>;
-		status = "okay";
+		pmu: pmu@8 {
+			reg = <0x08>;
+		};
 	};
 
 	sdio2: sdio@3f190000 {
 		non-removable;
 		max-frequency = <48000000>;
+		vmmc-supply = <&camldo1_reg>;
+		vqmmc-supply = <&iosr1_reg>;
 		status = "okay";
 	};
 
 	sdio4: sdio@3f1b0000 {
 		max-frequency = <48000000>;
 		cd-gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+		vmmc-supply = <&sdldo_reg>;
+		vqmmc-supply = <&sdxldo_reg>;
 		status = "okay";
 	};
 
 	usbotg: usb@3f120000 {
+		vusb_d-supply = <&usbldo_reg>;
+		vusb_a-supply = <&iosr1_reg>;
 		status = "okay";
 	};
 
@@ -74,3 +79,39 @@
 		status = "okay";
 	};
 };
+
+#include "bcm59056.dtsi"
+
+&pmu {
+	compatible = "brcm,bcm59056";
+	interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+	regulators {
+		camldo1_reg: camldo1 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		sdldo_reg: sdldo {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		sdxldo_reg: sdxldo {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		usbldo_reg: usbldo {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		iosr1_reg: iosr1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+	};
+};

arch/arm/boot/dts/bcm2835.dtsi

@@ -15,39 +15,52 @@
 		#size-cells = <1>;
 		ranges = <0x7e000000 0x20000000 0x02000000>;
 
-		timer {
+		timer@7e003000 {
 			compatible = "brcm,bcm2835-system-timer";
 			reg = <0x7e003000 0x1000>;
 			interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
 			clock-frequency = <1000000>;
 		};
 
-		intc: interrupt-controller {
+		dma: dma@7e007000 {
+			compatible = "brcm,bcm2835-dma";
+			reg = <0x7e007000 0xf00>;
+			interrupts = <1 16>,
+				     <1 17>,
+				     <1 18>,
+				     <1 19>,
+				     <1 20>,
+				     <1 21>,
+				     <1 22>,
+				     <1 23>,
+				     <1 24>,
+				     <1 25>,
+				     <1 26>,
+				     <1 27>,
+				     <1 28>;
+
+			#dma-cells = <1>;
+			brcm,dma-channel-mask = <0x7f35>;
+		};
+
+		intc: interrupt-controller@7e00b200 {
 			compatible = "brcm,bcm2835-armctrl-ic";
 			reg = <0x7e00b200 0x200>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 		};
 
-		watchdog {
+		watchdog@7e100000 {
 			compatible = "brcm,bcm2835-pm-wdt";
 			reg = <0x7e100000 0x28>;
 		};
 
-		rng {
+		rng@7e104000 {
 			compatible = "brcm,bcm2835-rng";
 			reg = <0x7e104000 0x10>;
 		};
 
-		uart@20201000 {
-			compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
-			reg = <0x7e201000 0x1000>;
-			interrupts = <2 25>;
-			clock-frequency = <3000000>;
-			arm,primecell-periphid = <0x00241011>;
-		};
-
-		gpio: gpio {
+		gpio: gpio@7e200000 {
 			compatible = "brcm,bcm2835-gpio";
 			reg = <0x7e200000 0xb4>;
 			/*
@@ -70,7 +83,25 @@
 			#interrupt-cells = <2>;
 		};
 
-		spi: spi@20204000 {
+		uart@7e201000 {
+			compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
+			reg = <0x7e201000 0x1000>;
+			interrupts = <2 25>;
+			clock-frequency = <3000000>;
+			arm,primecell-periphid = <0x00241011>;
+		};
+
+		i2s: i2s@7e203000 {
+			compatible = "brcm,bcm2835-i2s";
+			reg = <0x7e203000 0x20>,
+			      <0x7e101098 0x02>;
+
+			dmas = <&dma 2>,
+			       <&dma 3>;
+			dma-names = "tx", "rx";
+		};
+
+		spi: spi@7e204000 {
 			compatible = "brcm,bcm2835-spi";
 			reg = <0x7e204000 0x1000>;
 			interrupts = <2 22>;
@@ -90,7 +121,15 @@
 			status = "disabled";
 		};
 
-		i2c1: i2c@20804000 {
+		sdhci: sdhci@7e300000 {
+			compatible = "brcm,bcm2835-sdhci";
+			reg = <0x7e300000 0x100>;
+			interrupts = <2 30>;
+			clocks = <&clk_mmc>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@7e804000 {
 			compatible = "brcm,bcm2835-i2c";
 			reg = <0x7e804000 0x1000>;
 			interrupts = <2 21>;
@@ -100,19 +139,15 @@
 			status = "disabled";
 		};
 
-		sdhci: sdhci {
-			compatible = "brcm,bcm2835-sdhci";
-			reg = <0x7e300000 0x100>;
-			interrupts = <2 30>;
-			clocks = <&clk_mmc>;
-			status = "disabled";
-		};
-
-		usb {
+		usb@7e980000 {
 			compatible = "brcm,bcm2835-usb";
 			reg = <0x7e980000 0x10000>;
 			interrupts = <1 9>;
 		};
+
+		arm-pmu {
+			compatible = "arm,arm1176-pmu";
+		};
 	};
 
 	clocks {
@@ -120,24 +155,27 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		clk_mmc: mmc {
+		clk_mmc: clock@0 {
 			compatible = "fixed-clock";
 			reg = <0>;
 			#clock-cells = <0>;
+			clock-output-names = "mmc";
 			clock-frequency = <100000000>;
 		};
 
-		clk_i2c: i2c {
+		clk_i2c: clock@1 {
 			compatible = "fixed-clock";
 			reg = <1>;
 			#clock-cells = <0>;
+			clock-output-names = "i2c";
 			clock-frequency = <250000000>;
 		};
 
-		clk_spi: spi {
+		clk_spi: clock@2 {
 			compatible = "fixed-clock";
 			reg = <2>;
 			#clock-cells = <0>;
+			clock-output-names = "spi";
 			clock-frequency = <250000000>;
 		};
 	};

arch/arm/boot/dts/bcm4708-netgear-r6250.dts

@@ -0,0 +1,35 @@
+/*
+ * Broadcom BCM470X / BCM5301X arm platform code.
+ * DTS for Netgear R6250 V1
+ *
+ * Copyright 2013 Hauke Mehrtens <hauke@hauke-m.de>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+
+/ {
+	compatible = "netgear,r6250v1", "brcm,bcm4708";
+	model = "Netgear R6250 V1 (BCM4708)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000>;
+	};
+
+	chipcommonA {
+		uart0: serial@0300 {
+			status = "okay";
+		};
+
+		uart1: serial@0400 {
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/bcm4708.dtsi

@@ -0,0 +1,34 @@
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for BCM4708 SoC.
+ *
+ * Copyright 2013-2014 Hauke Mehrtens <hauke@hauke-m.de>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include "bcm5301x.dtsi"
+
+/ {
+	compatible = "brcm,bcm4708";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
+			reg = <0x0>;
+		};
+
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			next-level-cache = <&L2>;
+			reg = <0x1>;
+		};
+	};
+
+};

arch/arm/boot/dts/bcm5301x.dtsi

@@ -0,0 +1,95 @@
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * Generic DTS part for all BCM53010, BCM53011, BCM53012, BCM53014, BCM53015,
+ * BCM53016, BCM53017, BCM53018, BCM4707, BCM4708 and BCM4709 SoCs
+ *
+ * Copyright 2013-2014 Hauke Mehrtens <hauke@hauke-m.de>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "skeleton.dtsi"
+
+/ {
+	interrupt-parent = <&gic>;
+
+	chipcommonA {
+		compatible = "simple-bus";
+		ranges = <0x00000000 0x18000000 0x00001000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		uart0: serial@0300 {
+			compatible = "ns16550";
+			reg = <0x0300 0x100>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <100000000>;
+			status = "disabled";
+		};
+
+		uart1: serial@0400 {
+			compatible = "ns16550";
+			reg = <0x0400 0x100>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <100000000>;
+			status = "disabled";
+		};
+	};
+
+	mpcore {
+		compatible = "simple-bus";
+		ranges = <0x00000000 0x19020000 0x00003000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		scu@0000 {
+			compatible = "arm,cortex-a9-scu";
+			reg = <0x0000 0x100>;
+		};
+
+		timer@0200 {
+			compatible = "arm,cortex-a9-global-timer";
+			reg = <0x0200 0x100>;
+			interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_periph>;
+		};
+
+		local-timer@0600 {
+			compatible = "arm,cortex-a9-twd-timer";
+			reg = <0x0600 0x100>;
+			interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk_periph>;
+		};
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a9-gic";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>,
+			      <0x0100 0x100>;
+		};
+
+		L2: cache-controller@2000 {
+			compatible = "arm,pl310-cache";
+			reg = <0x2000 0x1000>;
+			cache-unified;
+			cache-level = <2>;
+		};
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* As long as we do not have a real clock driver us this
+		 * fixed clock */
+		clk_periph: periph {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <400000000>;
+		};
+	};
+};

arch/arm/boot/dts/bcm59056.dtsi

@@ -0,0 +1,74 @@
+/*
+* Copyright 2014 Linaro Limited
+* Author: Matt Porter <mporter@linaro.org>
+*
+* This program is free software; you can redistribute it and/or modify it
+* under  the terms of the GNU General  Public License as published by the
+* Free Software Foundation;  either version 2 of the License, or (at your
+* option) any later version.
+*/
+
+&pmu {
+	compatible = "brcm,bcm59056";
+	regulators {
+		rfldo_reg: rfldo {
+		};
+
+		camldo1_reg: camldo1 {
+		};
+
+		camldo2_reg: camldo2 {
+		};
+
+		simldo1_reg: simldo1 {
+		};
+
+		simldo2_reg: simldo2 {
+		};
+
+		sdldo_reg: sdldo {
+		};
+
+		sdxldo_reg: sdxldo {
+		};
+
+		mmcldo1_reg: mmcldo1 {
+		};
+
+		mmcldo2_reg: mmcldo2 {
+		};
+
+		audldo_reg: audldo {
+		};
+
+		micldo_reg: micldo {
+		};
+
+		usbldo_reg: usbldo {
+		};
+
+		vibldo_reg: vibldo {
+		};
+
+		csr_reg: csr {
+		};
+
+		iosr1_reg: iosr1 {
+		};
+
+		iosr2_reg: iosr2 {
+		};
+
+		msr_reg: msr {
+		};
+
+		sdsr1_reg: sdsr1 {
+		};
+
+		sdsr2_reg: sdsr2 {
+		};
+
+		vsr_reg: vsr {
+		};
+	};
+};

arch/arm/boot/dts/dove.dtsi

@@ -186,6 +186,11 @@
 				reg = <0x20000 0x80>, <0x800100 0x8>;
 			};
 
+			sysc: system-ctrl@20000 {
+				compatible = "marvell,orion-system-controller";
+				reg = <0x20000 0x110>;
+			};
+
 			bridge_intc: bridge-interrupt-ctrl@20110 {
 				compatible = "marvell,orion-bridge-intc";
 				interrupt-controller;
@@ -210,6 +215,14 @@
 				clocks = <&core_clk 0>;
 			};
 
+			watchdog@20300 {
+				compatible = "marvell,orion-wdt";
+				reg = <0x20300 0x28>, <0x20108 0x4>;
+				interrupt-parent = <&bridge_intc>;
+				interrupts = <3>;
+				clocks = <&core_clk 0>;
+			};
+
 			crypto: crypto-engine@30000 {
 				compatible = "marvell,orion-crypto";
 				reg = <0x30000 0x10000>,
@@ -381,7 +394,8 @@
 
 			pinctrl: pin-ctrl@d0200 {
 				compatible = "marvell,dove-pinctrl";
-				reg = <0xd0200 0x10>;
+				reg = <0xd0200 0x14>,
+				      <0xd0440 0x04>;
 				clocks = <&gate_clk 22>;
 
 				pmx_gpio_0: pmx-gpio-0 {
@@ -603,6 +617,12 @@
 				reg = <0xd8500 0x20>;
 			};
 
+			gconf: global-config@e802c {
+				compatible = "marvell,dove-global-config",
+				             "syscon";
+				reg = <0xe802c 0x14>;
+			};
+
 			gpio2: gpio-ctrl@e8400 {
 				compatible = "marvell,orion-gpio";
 				#gpio-cells = <2>;

arch/arm/boot/dts/dra7.dtsi

@@ -47,6 +47,11 @@
 				1000000	1060000
 				1176000	1160000
 				>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 		cpu@1 {
 			device_type = "cpu";
@@ -464,6 +469,20 @@
 			ti,hwmods = "wd_timer2";
 		};
 
+		hwspinlock: spinlock@4a0f6000 {
+			compatible = "ti,omap4-hwspinlock";
+			reg = <0x4a0f6000 0x1000>;
+			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
+		};
+
+		dmm@4e000000 {
+			compatible = "ti,omap5-dmm";
+			reg = <0x4e000000 0x800>;
+			interrupts = <0 113 0x4>;
+			ti,hwmods = "dmm";
+		};
+
 		i2c1: i2c@48070000 {
 			compatible = "ti,omap4-i2c";
 			reg = <0x48070000 0x100>;
@@ -559,6 +578,138 @@
 			status = "disabled";
 		};
 
+		abb_mpu: regulator-abb-mpu {
+			compatible = "ti,abb-v3";
+			regulator-name = "abb_mpu";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			clocks = <&sys_clkin1>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
+			      <0x4ae06014 0x4>, <0x4a003b20 0x8>,
+			      <0x4ae0c158 0x4>;
+			reg-names = "setup-address", "control-address",
+				    "int-address", "efuse-address",
+				    "ldo-address";
+			ti,tranxdone-status-mask = <0x80>;
+			/* LDOVBBMPU_FBB_MUX_CTRL */
+			ti,ldovbb-override-mask = <0x400>;
+			/* LDOVBBMPU_FBB_VSET_OUT */
+			ti,ldovbb-vset-mask = <0x1F>;
+
+			/*
+			 * NOTE: only FBB mode used but actual vset will
+			 * determine final biasing
+			 */
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+			1060000		0	0x0	0 0x02000000 0x01F00000
+			1160000		0	0x4	0 0x02000000 0x01F00000
+			1210000		0	0x8	0 0x02000000 0x01F00000
+			>;
+		};
+
+		abb_ivahd: regulator-abb-ivahd {
+			compatible = "ti,abb-v3";
+			regulator-name = "abb_ivahd";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			clocks = <&sys_clkin1>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
+			      <0x4ae06010 0x4>, <0x4a0025cc 0x8>,
+			      <0x4a002470 0x4>;
+			reg-names = "setup-address", "control-address",
+				    "int-address", "efuse-address",
+				    "ldo-address";
+			ti,tranxdone-status-mask = <0x40000000>;
+			/* LDOVBBIVA_FBB_MUX_CTRL */
+			ti,ldovbb-override-mask = <0x400>;
+			/* LDOVBBIVA_FBB_VSET_OUT */
+			ti,ldovbb-vset-mask = <0x1F>;
+
+			/*
+			 * NOTE: only FBB mode used but actual vset will
+			 * determine final biasing
+			 */
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+			1055000		0	0x0	0 0x02000000 0x01F00000
+			1150000		0	0x4	0 0x02000000 0x01F00000
+			1250000		0	0x8	0 0x02000000 0x01F00000
+			>;
+		};
+
+		abb_dspeve: regulator-abb-dspeve {
+			compatible = "ti,abb-v3";
+			regulator-name = "abb_dspeve";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			clocks = <&sys_clkin1>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
+			      <0x4ae06010 0x4>, <0x4a0025e0 0x8>,
+			      <0x4a00246c 0x4>;
+			reg-names = "setup-address", "control-address",
+				    "int-address", "efuse-address",
+				    "ldo-address";
+			ti,tranxdone-status-mask = <0x20000000>;
+			/* LDOVBBDSPEVE_FBB_MUX_CTRL */
+			ti,ldovbb-override-mask = <0x400>;
+			/* LDOVBBDSPEVE_FBB_VSET_OUT */
+			ti,ldovbb-vset-mask = <0x1F>;
+
+			/*
+			 * NOTE: only FBB mode used but actual vset will
+			 * determine final biasing
+			 */
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+			1055000		0	0x0	0 0x02000000 0x01F00000
+			1150000		0	0x4	0 0x02000000 0x01F00000
+			1250000		0	0x8	0 0x02000000 0x01F00000
+			>;
+		};
+
+		abb_gpu: regulator-abb-gpu {
+			compatible = "ti,abb-v3";
+			regulator-name = "abb_gpu";
+			#address-cells = <0>;
+			#size-cells = <0>;
+			clocks = <&sys_clkin1>;
+			ti,settling-time = <50>;
+			ti,clock-cycles = <16>;
+
+			reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
+			      <0x4ae06010 0x4>, <0x4a003b08 0x8>,
+			      <0x4ae0c154 0x4>;
+			reg-names = "setup-address", "control-address",
+				    "int-address", "efuse-address",
+				    "ldo-address";
+			ti,tranxdone-status-mask = <0x10000000>;
+			/* LDOVBBGPU_FBB_MUX_CTRL */
+			ti,ldovbb-override-mask = <0x400>;
+			/* LDOVBBGPU_FBB_VSET_OUT */
+			ti,ldovbb-vset-mask = <0x1F>;
+
+			/*
+			 * NOTE: only FBB mode used but actual vset will
+			 * determine final biasing
+			 */
+			ti,abb_info = <
+			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+			1090000		0	0x0	0 0x02000000 0x01F00000
+			1210000		0	0x4	0 0x02000000 0x01F00000
+			1280000		0	0x8	0 0x02000000 0x01F00000
+			>;
+		};
+
 		mcspi1: spi@48098000 {
 			compatible = "ti,omap4-mcspi";
 			reg = <0x48098000 0x200>;

arch/arm/boot/dts/efm32gg-dk3750.dts

@@ -26,7 +26,7 @@
 		};
 
 		i2c@4000a000 {
-			location = <3>;
+			efm32,location = <3>;
 			status = "ok";
 
 			temp@48 {

arch/arm/boot/dts/efm32gg.dtsi

@@ -84,7 +84,7 @@
 			status = "disabled";
 		};
 
-		spi2: spi@40x4000c800 { /* USART2 */
+		spi2: spi@4000c800 { /* USART2 */
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "efm32,spi";
@@ -110,7 +110,7 @@
 			status = "disabled";
 		};
 
-		uart2: uart@40x4000c800 { /* USART2 */
+		uart2: uart@4000c800 { /* USART2 */
 			compatible = "efm32,uart";
 			reg = <0x4000c800 0x400>;
 			interrupts = <18 19>;

arch/arm/boot/dts/exynos4.dtsi

@@ -19,6 +19,7 @@
  * published by the Free Software Foundation.
  */
 
+#include <dt-bindings/clock/exynos4.h>
 #include "skeleton.dtsi"
 
 / {
@@ -119,7 +120,7 @@
 			compatible = "samsung,exynos4210-fimc";
 			reg = <0x11800000 0x1000>;
 			interrupts = <0 84 0>;
-			clocks = <&clock 256>, <&clock 128>;
+			clocks = <&clock CLK_FIMC0>, <&clock CLK_SCLK_FIMC0>;
 			clock-names = "fimc", "sclk_fimc";
 			samsung,power-domain = <&pd_cam>;
 			samsung,sysreg = <&sys_reg>;
@@ -130,7 +131,7 @@
 			compatible = "samsung,exynos4210-fimc";
 			reg = <0x11810000 0x1000>;
 			interrupts = <0 85 0>;
-			clocks = <&clock 257>, <&clock 129>;
+			clocks = <&clock CLK_FIMC1>, <&clock CLK_SCLK_FIMC1>;
 			clock-names = "fimc", "sclk_fimc";
 			samsung,power-domain = <&pd_cam>;
 			samsung,sysreg = <&sys_reg>;
@@ -141,7 +142,7 @@
 			compatible = "samsung,exynos4210-fimc";
 			reg = <0x11820000 0x1000>;
 			interrupts = <0 86 0>;
-			clocks = <&clock 258>, <&clock 130>;
+			clocks = <&clock CLK_FIMC2>, <&clock CLK_SCLK_FIMC2>;
 			clock-names = "fimc", "sclk_fimc";
 			samsung,power-domain = <&pd_cam>;
 			samsung,sysreg = <&sys_reg>;
@@ -152,7 +153,7 @@
 			compatible = "samsung,exynos4210-fimc";
 			reg = <0x11830000 0x1000>;
 			interrupts = <0 87 0>;
-			clocks = <&clock 259>, <&clock 131>;
+			clocks = <&clock CLK_FIMC3>, <&clock CLK_SCLK_FIMC3>;
 			clock-names = "fimc", "sclk_fimc";
 			samsung,power-domain = <&pd_cam>;
 			samsung,sysreg = <&sys_reg>;
@@ -163,7 +164,7 @@
 			compatible = "samsung,exynos4210-csis";
 			reg = <0x11880000 0x4000>;
 			interrupts = <0 78 0>;
-			clocks = <&clock 260>, <&clock 134>;
+			clocks = <&clock CLK_CSIS0>, <&clock CLK_SCLK_CSIS0>;
 			clock-names = "csis", "sclk_csis";
 			bus-width = <4>;
 			samsung,power-domain = <&pd_cam>;
@@ -178,7 +179,7 @@
 			compatible = "samsung,exynos4210-csis";
 			reg = <0x11890000 0x4000>;
 			interrupts = <0 80 0>;
-			clocks = <&clock 261>, <&clock 135>;
+			clocks = <&clock CLK_CSIS1>, <&clock CLK_SCLK_CSIS1>;
 			clock-names = "csis", "sclk_csis";
 			bus-width = <2>;
 			samsung,power-domain = <&pd_cam>;
@@ -194,7 +195,7 @@
 		compatible = "samsung,s3c2410-wdt";
 		reg = <0x10060000 0x100>;
 		interrupts = <0 43 0>;
-		clocks = <&clock 345>;
+		clocks = <&clock CLK_WDT>;
 		clock-names = "watchdog";
 		status = "disabled";
 	};
@@ -203,7 +204,7 @@
 		compatible = "samsung,s3c6410-rtc";
 		reg = <0x10070000 0x100>;
 		interrupts = <0 44 0>, <0 45 0>;
-		clocks = <&clock 346>;
+		clocks = <&clock CLK_RTC>;
 		clock-names = "rtc";
 		status = "disabled";
 	};
@@ -212,7 +213,7 @@
 		compatible = "samsung,s5pv210-keypad";
 		reg = <0x100A0000 0x100>;
 		interrupts = <0 109 0>;
-		clocks = <&clock 347>;
+		clocks = <&clock CLK_KEYIF>;
 		clock-names = "keypad";
 		status = "disabled";
 	};
@@ -221,7 +222,7 @@
 		compatible = "samsung,exynos4210-sdhci";
 		reg = <0x12510000 0x100>;
 		interrupts = <0 73 0>;
-		clocks = <&clock 297>, <&clock 145>;
+		clocks = <&clock CLK_SDMMC0>, <&clock CLK_SCLK_MMC0>;
 		clock-names = "hsmmc", "mmc_busclk.2";
 		status = "disabled";
 	};
@@ -230,7 +231,7 @@
 		compatible = "samsung,exynos4210-sdhci";
 		reg = <0x12520000 0x100>;
 		interrupts = <0 74 0>;
-		clocks = <&clock 298>, <&clock 146>;
+		clocks = <&clock CLK_SDMMC1>, <&clock CLK_SCLK_MMC1>;
 		clock-names = "hsmmc", "mmc_busclk.2";
 		status = "disabled";
 	};
@@ -239,7 +240,7 @@
 		compatible = "samsung,exynos4210-sdhci";
 		reg = <0x12530000 0x100>;
 		interrupts = <0 75 0>;
-		clocks = <&clock 299>, <&clock 147>;
+		clocks = <&clock CLK_SDMMC2>, <&clock CLK_SCLK_MMC2>;
 		clock-names = "hsmmc", "mmc_busclk.2";
 		status = "disabled";
 	};
@@ -248,7 +249,7 @@
 		compatible = "samsung,exynos4210-sdhci";
 		reg = <0x12540000 0x100>;
 		interrupts = <0 76 0>;
-		clocks = <&clock 300>, <&clock 148>;
+		clocks = <&clock CLK_SDMMC3>, <&clock CLK_SCLK_MMC3>;
 		clock-names = "hsmmc", "mmc_busclk.2";
 		status = "disabled";
 	};
@@ -257,7 +258,7 @@
 		compatible = "samsung,exynos4210-ehci";
 		reg = <0x12580000 0x100>;
 		interrupts = <0 70 0>;
-		clocks = <&clock 304>;
+		clocks = <&clock CLK_USB_HOST>;
 		clock-names = "usbhost";
 		status = "disabled";
 	};
@@ -266,7 +267,7 @@
 		compatible = "samsung,exynos4210-ohci";
 		reg = <0x12590000 0x100>;
 		interrupts = <0 70 0>;
-		clocks = <&clock 304>;
+		clocks = <&clock CLK_USB_HOST>;
 		clock-names = "usbhost";
 		status = "disabled";
 	};
@@ -276,7 +277,7 @@
 		reg = <0x13400000 0x10000>;
 		interrupts = <0 94 0>;
 		samsung,power-domain = <&pd_mfc>;
-		clocks = <&clock 273>;
+		clocks = <&clock CLK_MFC>;
 		clock-names = "mfc";
 		status = "disabled";
 	};
@@ -285,7 +286,7 @@
 		compatible = "samsung,exynos4210-uart";
 		reg = <0x13800000 0x100>;
 		interrupts = <0 52 0>;
-		clocks = <&clock 312>, <&clock 151>;
+		clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
 		clock-names = "uart", "clk_uart_baud0";
 		status = "disabled";
 	};
@@ -294,7 +295,7 @@
 		compatible = "samsung,exynos4210-uart";
 		reg = <0x13810000 0x100>;
 		interrupts = <0 53 0>;
-		clocks = <&clock 313>, <&clock 152>;
+		clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
 		clock-names = "uart", "clk_uart_baud0";
 		status = "disabled";
 	};
@@ -303,7 +304,7 @@
 		compatible = "samsung,exynos4210-uart";
 		reg = <0x13820000 0x100>;
 		interrupts = <0 54 0>;
-		clocks = <&clock 314>, <&clock 153>;
+		clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
 		clock-names = "uart", "clk_uart_baud0";
 		status = "disabled";
 	};
@@ -312,7 +313,7 @@
 		compatible = "samsung,exynos4210-uart";
 		reg = <0x13830000 0x100>;
 		interrupts = <0 55 0>;
-		clocks = <&clock 315>, <&clock 154>;
+		clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
 		clock-names = "uart", "clk_uart_baud0";
 		status = "disabled";
 	};
@@ -323,7 +324,7 @@
 		compatible = "samsung,s3c2440-i2c";
 		reg = <0x13860000 0x100>;
 		interrupts = <0 58 0>;
-		clocks = <&clock 317>;
+		clocks = <&clock CLK_I2C0>;
 		clock-names = "i2c";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c0_bus>;
@@ -336,7 +337,7 @@
 		compatible = "samsung,s3c2440-i2c";
 		reg = <0x13870000 0x100>;
 		interrupts = <0 59 0>;
-		clocks = <&clock 318>;
+		clocks = <&clock CLK_I2C1>;
 		clock-names = "i2c";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c1_bus>;
@@ -349,7 +350,7 @@
 		compatible = "samsung,s3c2440-i2c";
 		reg = <0x13880000 0x100>;
 		interrupts = <0 60 0>;
-		clocks = <&clock 319>;
+		clocks = <&clock CLK_I2C2>;
 		clock-names = "i2c";
 		status = "disabled";
 	};
@@ -360,7 +361,7 @@
 		compatible = "samsung,s3c2440-i2c";
 		reg = <0x13890000 0x100>;
 		interrupts = <0 61 0>;
-		clocks = <&clock 320>;
+		clocks = <&clock CLK_I2C3>;
 		clock-names = "i2c";
 		status = "disabled";
 	};
@@ -371,7 +372,7 @@
 		compatible = "samsung,s3c2440-i2c";
 		reg = <0x138A0000 0x100>;
 		interrupts = <0 62 0>;
-		clocks = <&clock 321>;
+		clocks = <&clock CLK_I2C4>;
 		clock-names = "i2c";
 		status = "disabled";
 	};
@@ -382,7 +383,7 @@
 		compatible = "samsung,s3c2440-i2c";
 		reg = <0x138B0000 0x100>;
 		interrupts = <0 63 0>;
-		clocks = <&clock 322>;
+		clocks = <&clock CLK_I2C5>;
 		clock-names = "i2c";
 		status = "disabled";
 	};
@@ -393,7 +394,7 @@
 		compatible = "samsung,s3c2440-i2c";
 		reg = <0x138C0000 0x100>;
 		interrupts = <0 64 0>;
-		clocks = <&clock 323>;
+		clocks = <&clock CLK_I2C6>;
 		clock-names = "i2c";
 		status = "disabled";
 	};
@@ -404,7 +405,7 @@
 		compatible = "samsung,s3c2440-i2c";
 		reg = <0x138D0000 0x100>;
 		interrupts = <0 65 0>;
-		clocks = <&clock 324>;
+		clocks = <&clock CLK_I2C7>;
 		clock-names = "i2c";
 		status = "disabled";
 	};
@@ -417,7 +418,7 @@
 		dma-names = "tx", "rx";
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 327>, <&clock 159>;
+		clocks = <&clock CLK_SPI0>, <&clock CLK_SCLK_SPI0>;
 		clock-names = "spi", "spi_busclk0";
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi0_bus>;
@@ -432,7 +433,7 @@
 		dma-names = "tx", "rx";
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 328>, <&clock 160>;
+		clocks = <&clock CLK_SPI1>, <&clock CLK_SCLK_SPI1>;
 		clock-names = "spi", "spi_busclk0";
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi1_bus>;
@@ -447,7 +448,7 @@
 		dma-names = "tx", "rx";
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 329>, <&clock 161>;
+		clocks = <&clock CLK_SPI2>, <&clock CLK_SCLK_SPI2>;
 		clock-names = "spi", "spi_busclk0";
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi2_bus>;
@@ -458,7 +459,7 @@
 		compatible = "samsung,exynos4210-pwm";
 		reg = <0x139D0000 0x1000>;
 		interrupts = <0 37 0>, <0 38 0>, <0 39 0>, <0 40 0>, <0 41 0>;
-		clocks = <&clock 336>;
+		clocks = <&clock CLK_PWM>;
 		clock-names = "timers";
 		#pwm-cells = <2>;
 		status = "disabled";
@@ -475,7 +476,7 @@
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x12680000 0x1000>;
 			interrupts = <0 35 0>;
-			clocks = <&clock 292>;
+			clocks = <&clock CLK_PDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
 			#dma-channels = <8>;
@@ -486,7 +487,7 @@
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x12690000 0x1000>;
 			interrupts = <0 36 0>;
-			clocks = <&clock 293>;
+			clocks = <&clock CLK_PDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
 			#dma-channels = <8>;
@@ -497,7 +498,7 @@
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x12850000 0x1000>;
 			interrupts = <0 34 0>;
-			clocks = <&clock 279>;
+			clocks = <&clock CLK_MDMA>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
 			#dma-channels = <8>;
@@ -511,7 +512,7 @@
 		reg = <0x11c00000 0x20000>;
 		interrupt-names = "fifo", "vsync", "lcd_sys";
 		interrupts = <11 0>, <11 1>, <11 2>;
-		clocks = <&clock 140>, <&clock 283>;
+		clocks = <&clock CLK_SCLK_FIMD0>, <&clock CLK_FIMD0>;
 		clock-names = "sclk_fimd", "fimd";
 		samsung,power-domain = <&pd_lcd0>;
 		status = "disabled";

arch/arm/boot/dts/exynos4210.dtsi

@@ -53,7 +53,7 @@
 		reg = <0x10050000 0x800>;
 		interrupt-parent = <&mct_map>;
 		interrupts = <0>, <1>, <2>, <3>, <4>, <5>;
-		clocks = <&clock 3>, <&clock 344>;
+		clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>;
 		clock-names = "fin_pll", "mct";
 
 		mct_map: mct-map {
@@ -109,7 +109,7 @@
 		interrupt-parent = <&combiner>;
 		reg = <0x100C0000 0x100>;
 		interrupts = <2 4>;
-		clocks = <&clock 383>;
+		clocks = <&clock CLK_TMU_APBIF>;
 		clock-names = "tmu_apbif";
 		status = "disabled";
 	};
@@ -118,13 +118,14 @@
 		compatible = "samsung,s5pv210-g2d";
 		reg = <0x12800000 0x1000>;
 		interrupts = <0 89 0>;
-		clocks = <&clock 177>, <&clock 277>;
+		clocks = <&clock CLK_SCLK_FIMG2D>, <&clock CLK_G2D>;
 		clock-names = "sclk_fimg2d", "fimg2d";
 		status = "disabled";
 	};
 
 	camera {
-		clocks = <&clock 132>, <&clock 133>, <&clock 351>, <&clock 352>;
+		clocks = <&clock CLK_SCLK_CAM0>, <&clock CLK_SCLK_CAM1>,
+			 <&clock CLK_PIXELASYNCM0>, <&clock CLK_PIXELASYNCM1>;
 		clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", "pxl_async1";
 
 		fimc_0: fimc@11800000 {

arch/arm/boot/dts/exynos4412-odroidx.dts

@@ -251,7 +251,7 @@
 				buck2_reg: BUCK2 {
 					regulator-name = "vdd_arm";
 					regulator-min-microvolt = <900000>;
-					regulator-max-microvolt = <1300000>;
+					regulator-max-microvolt = <1350000>;
 					regulator-always-on;
 					regulator-boot-on;
 				};

arch/arm/boot/dts/exynos4412-origen.dts

@@ -459,8 +459,8 @@
 
 				buck2_reg: BUCK2 {
 					regulator-name = "vdd_arm";
-					regulator-min-microvolt = <925000>;
-					regulator-max-microvolt	= <1300000>;
+					regulator-min-microvolt = <900000>;
+					regulator-max-microvolt	= <1350000>;
 					regulator-always-on;
 					regulator-boot-on;
 					op_mode = <1>; /* Normal Mode */

arch/arm/boot/dts/exynos4x12.dtsi

@@ -47,7 +47,7 @@
 		reg = <0x10050000 0x800>;
 		interrupt-parent = <&mct_map>;
 		interrupts = <0>, <1>, <2>, <3>, <4>;
-		clocks = <&clock 3>, <&clock 344>;
+		clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>;
 		clock-names = "fin_pll", "mct";
 
 		mct_map: mct-map {
@@ -97,13 +97,14 @@
 		compatible = "samsung,exynos4212-g2d";
 		reg = <0x10800000 0x1000>;
 		interrupts = <0 89 0>;
-		clocks = <&clock 177>, <&clock 277>;
+		clocks = <&clock CLK_SCLK_FIMG2D>, <&clock CLK_G2D>;
 		clock-names = "sclk_fimg2d", "fimg2d";
 		status = "disabled";
 	};
 
 	camera {
-		clocks = <&clock 132>, <&clock 133>, <&clock 351>, <&clock 352>;
+		clocks = <&clock CLK_SCLK_CAM0>, <&clock CLK_SCLK_CAM1>,
+			 <&clock CLK_PIXELASYNCM0>, <&clock CLK_PIXELASYNCM1>;
 		clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", "pxl_async1";
 
 		fimc_0: fimc@11800000 {
@@ -145,7 +146,7 @@
 			reg = <0x12390000 0x1000>;
 			interrupts = <0 105 0>;
 			samsung,power-domain = <&pd_isp>;
-			clocks = <&clock 353>;
+			clocks = <&clock CLK_FIMC_LITE0>;
 			clock-names = "flite";
 			status = "disabled";
 		};
@@ -155,7 +156,7 @@
 			reg = <0x123A0000 0x1000>;
 			interrupts = <0 106 0>;
 			samsung,power-domain = <&pd_isp>;
-			clocks = <&clock 354>;
+			clocks = <&clock CLK_FIMC_LITE1>;
 			clock-names = "flite";
 			status = "disabled";
 		};
@@ -165,12 +166,19 @@
 			reg = <0x12000000 0x260000>;
 			interrupts = <0 90 0>, <0 95 0>;
 			samsung,power-domain = <&pd_isp>;
-			clocks = <&clock 353>, <&clock 354>, <&clock 355>,
-				<&clock 356>, <&clock 17>, <&clock 357>,
-				<&clock 358>, <&clock 359>, <&clock 360>,
-				<&clock 450>,<&clock 451>, <&clock 452>,
-				<&clock 453>, <&clock 176>, <&clock 13>,
-				<&clock 454>, <&clock 395>, <&clock 455>;
+			clocks = <&clock CLK_FIMC_LITE0>,
+				 <&clock CLK_FIMC_LITE1>, <&clock CLK_PPMUISPX>,
+				 <&clock CLK_PPMUISPMX>,
+				 <&clock CLK_MOUT_MPLL_USER_T>,
+				 <&clock CLK_FIMC_ISP>, <&clock CLK_FIMC_DRC>,
+				 <&clock CLK_FIMC_FD>, <&clock CLK_MCUISP>,
+				 <&clock CLK_DIV_ISP0>,<&clock CLK_DIV_ISP1>,
+				 <&clock CLK_DIV_MCUISP0>,
+				 <&clock CLK_DIV_MCUISP1>,
+				 <&clock CLK_SCLK_UART_ISP>,
+				 <&clock CLK_ACLK200>, <&clock CLK_DIV_ACLK200>,
+				 <&clock CLK_ACLK400_MCUISP>,
+				 <&clock CLK_DIV_ACLK400_MCUISP>;
 			clock-names = "lite0", "lite1", "ppmuispx",
 				      "ppmuispmx", "mpll", "isp",
 				      "drc", "fd", "mcuisp",
@@ -190,7 +198,7 @@
 			i2c1_isp: i2c-isp@12140000 {
 				compatible = "samsung,exynos4212-i2c-isp";
 				reg = <0x12140000 0x100>;
-				clocks = <&clock 370>;
+				clocks = <&clock CLK_I2C1_ISP>;
 				clock-names = "i2c_isp";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -205,7 +213,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		fifo-depth = <0x80>;
-		clocks = <&clock 301>, <&clock 149>;
+		clocks = <&clock CLK_SDMMC4>, <&clock CLK_SCLK_MMC4>;
 		clock-names = "biu", "ciu";
 		status = "disabled";
 	};

arch/arm/boot/dts/exynos5.dtsi

@@ -81,13 +81,6 @@
 		status = "disabled";
 	};
 
-	watchdog {
-		compatible = "samsung,s3c2410-wdt";
-		reg = <0x101D0000 0x100>;
-		interrupts = <0 42 0>;
-		status = "disabled";
-	};
-
 	fimd@14400000 {
 		compatible = "samsung,exynos5250-fimd";
 		interrupt-parent = <&combiner>;

arch/arm/boot/dts/exynos5250-arndale.dts

@@ -25,6 +25,10 @@
 		bootargs = "console=ttySAC2,115200";
 	};
 
+	rtc@101E0000 {
+		status = "okay";
+	};
+
 	codec@11000000 {
 		samsung,mfc-r = <0x43000000 0x800000>;
 		samsung,mfc-l = <0x51000000 0x800000>;

arch/arm/boot/dts/exynos5250-smdk5250.dts

@@ -27,6 +27,10 @@
 		bootargs = "root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC2,115200 init=/linuxrc";
 	};
 
+	rtc@101E0000 {
+		status = "okay";
+	};
+
 	i2c@12C60000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <20000>;
@@ -36,6 +40,148 @@
 			compatible = "samsung,s524ad0xd1";
 			reg = <0x50>;
 		};
+
+		max77686@09 {
+			compatible = "maxim,max77686";
+			reg = <0x09>;
+
+			voltage-regulators {
+				ldo1_reg: LDO1 {
+					regulator-name = "P1.0V_LDO_OUT1";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+				};
+
+				ldo2_reg: LDO2 {
+					regulator-name = "P1.2V_LDO_OUT2";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				ldo3_reg: LDO3 {
+					regulator-name = "P1.8V_LDO_OUT3";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo4_reg: LDO4 {
+					regulator-name = "P2.8V_LDO_OUT4";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+				};
+
+				ldo5_reg: LDO5 {
+					regulator-name = "P1.8V_LDO_OUT5";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo6_reg: LDO6 {
+					regulator-name = "P1.1V_LDO_OUT6";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+				};
+
+				ldo7_reg: LDO7 {
+					regulator-name = "P1.1V_LDO_OUT7";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+				};
+
+				ldo8_reg: LDO8 {
+					regulator-name = "P1.0V_LDO_OUT8";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+				};
+
+				ldo10_reg: LDO10 {
+					regulator-name = "P1.8V_LDO_OUT10";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo11_reg: LDO11 {
+					regulator-name = "P1.8V_LDO_OUT11";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo12_reg: LDO12 {
+					regulator-name = "P3.0V_LDO_OUT12";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+				};
+
+				ldo13_reg: LDO13 {
+					regulator-name = "P1.8V_LDO_OUT13";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo14_reg: LDO14 {
+					regulator-name = "P1.8V_LDO_OUT14";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo15_reg: LDO15 {
+					regulator-name = "P1.0V_LDO_OUT15";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+				};
+
+				ldo16_reg: LDO16 {
+					regulator-name = "P1.8V_LDO_OUT16";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				buck1_reg: BUCK1 {
+					regulator-name = "vdd_mif";
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck2_reg: BUCK2 {
+					regulator-name = "vdd_arm";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1350000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck3_reg: BUCK3 {
+					regulator-name = "vdd_int";
+					regulator-min-microvolt = <900000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck4_reg: BUCK4 {
+					regulator-name = "vdd_g3d";
+					regulator-min-microvolt = <850000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck5_reg: BUCK5 {
+					regulator-name = "P1.8V_BUCK_OUT5";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+			};
+		};
 	};
 
 	vdd: fixed-regulator@0 {

arch/arm/boot/dts/exynos5250-snow.dts

@@ -20,6 +20,10 @@
 		i2c104 = &i2c_104;
 	};
 
+	rtc@101E0000 {
+		status = "okay";
+	};
+
 	pinctrl@11400000 {
 		sd3_clk: sd3-clk {
 			samsung,pin-drv = <0>;

arch/arm/boot/dts/exynos5250.dtsi

@@ -17,6 +17,7 @@
  * published by the Free Software Foundation.
 */
 
+#include <dt-bindings/clock/exynos5250.h>
 #include "exynos5.dtsi"
 #include "exynos5250-pinctrl.dtsi"
 
@@ -90,7 +91,8 @@
 		compatible = "samsung,exynos5250-audss-clock";
 		reg = <0x03810000 0x0C>;
 		#clock-cells = <1>;
-		clocks = <&clock 1>, <&clock 7>, <&clock 138>, <&clock 160>;
+		clocks = <&clock CLK_FIN_PLL>, <&clock CLK_FOUT_EPLL>,
+			 <&clock CLK_SCLK_AUDIO0>, <&clock CLK_DIV_PCM0>;
 		clock-names = "pll_ref", "pll_in", "sclk_audio", "sclk_pcm_in";
 	};
 
@@ -115,7 +117,7 @@
 		interrupt-parent = <&mct_map>;
 		interrupts = <0 0>, <1 0>, <2 0>, <3 0>,
 			     <4 0>, <5 0>;
-		clocks = <&clock 1>, <&clock 335>;
+		clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>;
 		clock-names = "fin_pll", "mct";
 
 		mct_map: mct-map {
@@ -167,16 +169,25 @@
 		interrupts = <0 47 0>;
 	};
 
-	watchdog {
-		clocks = <&clock 336>;
+	pmu_system_controller: system-controller@10040000 {
+		compatible = "samsung,exynos5250-pmu", "syscon";
+		reg = <0x10040000 0x5000>;
+	};
+
+	watchdog@101D0000 {
+		compatible = "samsung,exynos5250-wdt";
+		reg = <0x101D0000 0x100>;
+		interrupts = <0 42 0>;
+		clocks = <&clock CLK_WDT>;
 		clock-names = "watchdog";
+		samsung,syscon-phandle = <&pmu_system_controller>;
 	};
 
 	g2d@10850000 {
 		compatible = "samsung,exynos5250-g2d";
 		reg = <0x10850000 0x1000>;
 		interrupts = <0 91 0>;
-		clocks = <&clock 345>;
+		clocks = <&clock CLK_G2D>;
 		clock-names = "fimg2d";
 	};
 
@@ -185,41 +196,41 @@
 		reg = <0x11000000 0x10000>;
 		interrupts = <0 96 0>;
 		samsung,power-domain = <&pd_mfc>;
-		clocks = <&clock 266>;
+		clocks = <&clock CLK_MFC>;
 		clock-names = "mfc";
 	};
 
 	rtc@101E0000 {
-		clocks = <&clock 337>;
+		clocks = <&clock CLK_RTC>;
 		clock-names = "rtc";
-		status = "okay";
+		status = "disabled";
 	};
 
 	tmu@10060000 {
 		compatible = "samsung,exynos5250-tmu";
 		reg = <0x10060000 0x100>;
 		interrupts = <0 65 0>;
-		clocks = <&clock 338>;
+		clocks = <&clock CLK_TMU>;
 		clock-names = "tmu_apbif";
 	};
 
 	serial@12C00000 {
-		clocks = <&clock 289>, <&clock 146>;
+		clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
 		clock-names = "uart", "clk_uart_baud0";
 	};
 
 	serial@12C10000 {
-		clocks = <&clock 290>, <&clock 147>;
+		clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
 		clock-names = "uart", "clk_uart_baud0";
 	};
 
 	serial@12C20000 {
-		clocks = <&clock 291>, <&clock 148>;
+		clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
 		clock-names = "uart", "clk_uart_baud0";
 	};
 
 	serial@12C30000 {
-		clocks = <&clock 292>, <&clock 149>;
+		clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
 		clock-names = "uart", "clk_uart_baud0";
 	};
 
@@ -227,7 +238,7 @@
 		compatible = "samsung,exynos5-sata-ahci";
 		reg = <0x122F0000 0x1ff>;
 		interrupts = <0 115 0>;
-		clocks = <&clock 277>, <&clock 143>;
+		clocks = <&clock CLK_SATA>, <&clock CLK_SCLK_SATA>;
 		clock-names = "sata", "sclk_sata";
 	};
 
@@ -242,7 +253,7 @@
 		interrupts = <0 56 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 294>;
+		clocks = <&clock CLK_I2C0>;
 		clock-names = "i2c";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c0_bus>;
@@ -255,7 +266,7 @@
 		interrupts = <0 57 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 295>;
+		clocks = <&clock CLK_I2C1>;
 		clock-names = "i2c";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c1_bus>;
@@ -268,7 +279,7 @@
 		interrupts = <0 58 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 296>;
+		clocks = <&clock CLK_I2C2>;
 		clock-names = "i2c";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c2_bus>;
@@ -281,7 +292,7 @@
 		interrupts = <0 59 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 297>;
+		clocks = <&clock CLK_I2C3>;
 		clock-names = "i2c";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c3_bus>;
@@ -294,7 +305,7 @@
 		interrupts = <0 60 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 298>;
+		clocks = <&clock CLK_I2C4>;
 		clock-names = "i2c";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c4_bus>;
@@ -307,7 +318,7 @@
 		interrupts = <0 61 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 299>;
+		clocks = <&clock CLK_I2C5>;
 		clock-names = "i2c";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c5_bus>;
@@ -320,7 +331,7 @@
 		interrupts = <0 62 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 300>;
+		clocks = <&clock CLK_I2C6>;
 		clock-names = "i2c";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c6_bus>;
@@ -333,7 +344,7 @@
 		interrupts = <0 63 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 301>;
+		clocks = <&clock CLK_I2C7>;
 		clock-names = "i2c";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c7_bus>;
@@ -346,7 +357,7 @@
 		interrupts = <0 64 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 302>;
+		clocks = <&clock CLK_I2C_HDMI>;
 		clock-names = "i2c";
 		status = "disabled";
 	};
@@ -356,7 +367,7 @@
                 reg = <0x121D0000 0x100>;
                 #address-cells = <1>;
                 #size-cells = <0>;
-		clocks = <&clock 288>;
+		clocks = <&clock CLK_SATA_PHYI2C>;
 		clock-names = "i2c";
 		status = "disabled";
 	};
@@ -371,7 +382,7 @@
 		dma-names = "tx", "rx";
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 304>, <&clock 154>;
+		clocks = <&clock CLK_SPI0>, <&clock CLK_SCLK_SPI0>;
 		clock-names = "spi", "spi_busclk0";
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi0_bus>;
@@ -387,7 +398,7 @@
 		dma-names = "tx", "rx";
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 305>, <&clock 155>;
+		clocks = <&clock CLK_SPI1>, <&clock CLK_SCLK_SPI1>;
 		clock-names = "spi", "spi_busclk0";
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi1_bus>;
@@ -403,7 +414,7 @@
 		dma-names = "tx", "rx";
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 306>, <&clock 156>;
+		clocks = <&clock CLK_SPI2>, <&clock CLK_SCLK_SPI2>;
 		clock-names = "spi", "spi_busclk0";
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi2_bus>;
@@ -415,7 +426,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0x12200000 0x1000>;
-		clocks = <&clock 280>, <&clock 139>;
+		clocks = <&clock CLK_SDMMC0>, <&clock CLK_SCLK_MMC0>;
 		clock-names = "biu", "ciu";
 		fifo-depth = <0x80>;
 		status = "disabled";
@@ -427,7 +438,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0x12210000 0x1000>;
-		clocks = <&clock 281>, <&clock 140>;
+		clocks = <&clock CLK_SDMMC1>, <&clock CLK_SCLK_MMC1>;
 		clock-names = "biu", "ciu";
 		fifo-depth = <0x80>;
 		status = "disabled";
@@ -439,7 +450,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0x12220000 0x1000>;
-		clocks = <&clock 282>, <&clock 141>;
+		clocks = <&clock CLK_SDMMC2>, <&clock CLK_SCLK_MMC2>;
 		clock-names = "biu", "ciu";
 		fifo-depth = <0x80>;
 		status = "disabled";
@@ -451,7 +462,7 @@
 		interrupts = <0 78 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 283>, <&clock 142>;
+		clocks = <&clock CLK_SDMMC3>, <&clock CLK_SCLK_MMC3>;
 		clock-names = "biu", "ciu";
 		fifo-depth = <0x80>;
 		status = "disabled";
@@ -481,7 +492,7 @@
 		dmas = <&pdma1 12
 			&pdma1 11>;
 		dma-names = "tx", "rx";
-		clocks = <&clock 307>, <&clock 157>;
+		clocks = <&clock CLK_I2S1>, <&clock CLK_DIV_I2S1>;
 		clock-names = "iis", "i2s_opclk0";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2s1_bus>;
@@ -494,7 +505,7 @@
 		dmas = <&pdma0 12
 			&pdma0 11>;
 		dma-names = "tx", "rx";
-		clocks = <&clock 308>, <&clock 158>;
+		clocks = <&clock CLK_I2S2>, <&clock CLK_DIV_I2S2>;
 		clock-names = "iis", "i2s_opclk0";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2s2_bus>;
@@ -502,7 +513,7 @@
 
 	usb@12000000 {
 		compatible = "samsung,exynos5250-dwusb3";
-		clocks = <&clock 286>;
+		clocks = <&clock CLK_USB3>;
 		clock-names = "usbdrd30";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -519,7 +530,7 @@
 	usb3_phy: usbphy@12100000 {
 		compatible = "samsung,exynos5250-usb3phy";
 		reg = <0x12100000 0x100>;
-		clocks = <&clock 1>, <&clock 286>;
+		clocks = <&clock CLK_FIN_PLL>, <&clock CLK_USB3>;
 		clock-names = "ext_xtal", "usbdrd30";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -535,7 +546,7 @@
 		reg = <0x12110000 0x100>;
 		interrupts = <0 71 0>;
 
-		clocks = <&clock 285>;
+		clocks = <&clock CLK_USB2>;
 		clock-names = "usbhost";
 	};
 
@@ -544,14 +555,14 @@
 		reg = <0x12120000 0x100>;
 		interrupts = <0 71 0>;
 
-		clocks = <&clock 285>;
+		clocks = <&clock CLK_USB2>;
 		clock-names = "usbhost";
 	};
 
 	usb2_phy: usbphy@12130000 {
 		compatible = "samsung,exynos5250-usb2phy";
 		reg = <0x12130000 0x100>;
-		clocks = <&clock 1>, <&clock 285>;
+		clocks = <&clock CLK_FIN_PLL>, <&clock CLK_USB2>;
 		clock-names = "ext_xtal", "usbhost";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -568,7 +579,7 @@
 		reg = <0x12dd0000 0x100>;
 		samsung,pwm-outputs = <0>, <1>, <2>, <3>;
 		#pwm-cells = <3>;
-		clocks = <&clock 311>;
+		clocks = <&clock CLK_PWM>;
 		clock-names = "timers";
 	};
 
@@ -583,7 +594,7 @@
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121A0000 0x1000>;
 			interrupts = <0 34 0>;
-			clocks = <&clock 275>;
+			clocks = <&clock CLK_PDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
 			#dma-channels = <8>;
@@ -594,7 +605,7 @@
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121B0000 0x1000>;
 			interrupts = <0 35 0>;
-			clocks = <&clock 276>;
+			clocks = <&clock CLK_PDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
 			#dma-channels = <8>;
@@ -605,7 +616,7 @@
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x10800000 0x1000>;
 			interrupts = <0 33 0>;
-			clocks = <&clock 346>;
+			clocks = <&clock CLK_MDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
 			#dma-channels = <8>;
@@ -616,7 +627,7 @@
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x11C10000 0x1000>;
 			interrupts = <0 124 0>;
-			clocks = <&clock 271>;
+			clocks = <&clock CLK_MDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
 			#dma-channels = <8>;
@@ -629,7 +640,7 @@
 		reg = <0x13e00000 0x1000>;
 		interrupts = <0 85 0>;
 		samsung,power-domain = <&pd_gsc>;
-		clocks = <&clock 256>;
+		clocks = <&clock CLK_GSCL0>;
 		clock-names = "gscl";
 	};
 
@@ -638,7 +649,7 @@
 		reg = <0x13e10000 0x1000>;
 		interrupts = <0 86 0>;
 		samsung,power-domain = <&pd_gsc>;
-		clocks = <&clock 257>;
+		clocks = <&clock CLK_GSCL1>;
 		clock-names = "gscl";
 	};
 
@@ -647,7 +658,7 @@
 		reg = <0x13e20000 0x1000>;
 		interrupts = <0 87 0>;
 		samsung,power-domain = <&pd_gsc>;
-		clocks = <&clock 258>;
+		clocks = <&clock CLK_GSCL2>;
 		clock-names = "gscl";
 	};
 
@@ -656,7 +667,7 @@
 		reg = <0x13e30000 0x1000>;
 		interrupts = <0 88 0>;
 		samsung,power-domain = <&pd_gsc>;
-		clocks = <&clock 259>;
+		clocks = <&clock CLK_GSCL3>;
 		clock-names = "gscl";
 	};
 
@@ -664,8 +675,9 @@
 		compatible = "samsung,exynos4212-hdmi";
 		reg = <0x14530000 0x70000>;
 		interrupts = <0 95 0>;
-		clocks = <&clock 344>, <&clock 136>, <&clock 137>,
-				<&clock 159>, <&clock 1024>;
+		clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>,
+			 <&clock CLK_SCLK_PIXEL>, <&clock CLK_SCLK_HDMIPHY>,
+			 <&clock CLK_MOUT_HDMI>;
 		clock-names = "hdmi", "sclk_hdmi", "sclk_pixel",
 				"sclk_hdmiphy", "mout_hdmi";
 	};
@@ -674,7 +686,7 @@
 		compatible = "samsung,exynos5250-mixer";
 		reg = <0x14450000 0x10000>;
 		interrupts = <0 94 0>;
-		clocks = <&clock 343>, <&clock 136>;
+		clocks = <&clock CLK_MIXER>, <&clock CLK_SCLK_HDMI>;
 		clock-names = "mixer", "sclk_hdmi";
 	};
 
@@ -685,14 +697,14 @@
 	};
 
 	dp-controller@145B0000 {
-		clocks = <&clock 342>;
+		clocks = <&clock CLK_DP>;
 		clock-names = "dp";
 		phys = <&dp_phy>;
 		phy-names = "dp";
 	};
 
 	fimd@14400000 {
-		clocks = <&clock 133>, <&clock 339>;
+		clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
 		clock-names = "sclk_fimd", "fimd";
 	};
 
@@ -700,7 +712,7 @@
 		compatible = "samsung,exynos-adc-v1";
 		reg = <0x12D10000 0x100>, <0x10040718 0x4>;
 		interrupts = <0 106 0>;
-		clocks = <&clock 303>;
+		clocks = <&clock CLK_ADC>;
 		clock-names = "adc";
 		#io-channel-cells = <1>;
 		io-channel-ranges;

arch/arm/boot/dts/exynos5420-arndale-octa.dts

@@ -11,6 +11,8 @@
 
 /dts-v1/;
 #include "exynos5420.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Insignal Arndale Octa evaluation board based on EXYNOS5420";
@@ -31,6 +33,10 @@
 		};
 	};
 
+	rtc@101E0000 {
+		status = "okay";
+	};
+
 	mmc@12200000 {
 		status = "okay";
 		broken-cd;
@@ -41,6 +47,7 @@
 		samsung,dw-mshc-ddr-timing = <0 2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
+		vmmc-supply = <&ldo10_reg>;
 
 		slot@0 {
 			reg = <0>;
@@ -57,10 +64,301 @@
 		samsung,dw-mshc-ddr-timing = <1 2>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+		vmmc-supply = <&ldo10_reg>;
 
 		slot@0 {
 			reg = <0>;
 			bus-width = <4>;
 		};
 	};
+
+	hsi2c_4: i2c@12CA0000 {
+		status = "okay";
+
+		s2mps11_pmic@66 {
+			compatible = "samsung,s2mps11-pmic";
+			reg = <0x66>;
+			s2mps11,buck2-ramp-delay = <12>;
+			s2mps11,buck34-ramp-delay = <12>;
+			s2mps11,buck16-ramp-delay = <12>;
+			s2mps11,buck6-ramp-enable = <1>;
+			s2mps11,buck2-ramp-enable = <1>;
+			s2mps11,buck3-ramp-enable = <1>;
+			s2mps11,buck4-ramp-enable = <1>;
+
+			interrupt-parent = <&gpx3>;
+			interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+
+			s2mps11_osc: clocks {
+				#clock-cells = <1>;
+				clock-output-names = "s2mps11_ap",
+						"s2mps11_cp", "s2mps11_bt";
+			};
+
+			regulators {
+				ldo1_reg: LDO1 {
+					regulator-name = "PVDD_ALIVE_1V0";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+				};
+
+				ldo2_reg: LDO2 {
+					regulator-name = "PVDD_APIO_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo3_reg: LDO3 {
+					regulator-name = "PVDD_APIO_MMCON_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo4_reg: LDO4 {
+					regulator-name = "PVDD_ADC_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo5_reg: LDO5 {
+					regulator-name = "PVDD_PLL_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo6_reg: LDO6 {
+					regulator-name = "PVDD_ANAIP_1V0";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+				};
+
+				ldo7_reg: LDO7 {
+					regulator-name = "PVDD_ANAIP_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo8_reg: LDO8 {
+					regulator-name = "PVDD_ABB_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo9_reg: LDO9 {
+					regulator-name = "PVDD_USB_3V3";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+				};
+
+				ldo10_reg: LDO10 {
+					regulator-name = "PVDD_PRE_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo11_reg: LDO11 {
+					regulator-name = "PVDD_USB_1V0";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+				};
+
+				ldo12_reg: LDO12 {
+					regulator-name = "PVDD_HSIC_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo13_reg: LDO13 {
+					regulator-name = "PVDD_APIO_MMCOFF_2V8";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+				};
+
+				ldo15_reg: LDO15 {
+					regulator-name = "PVDD_PERI_2V8";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				ldo16_reg: LDO16 {
+					regulator-name = "PVDD_PERI_3V3";
+					regulator-min-microvolt = <2200000>;
+					regulator-max-microvolt = <2200000>;
+				};
+
+				ldo18_reg: LDO18 {
+					regulator-name = "PVDD_EMMC_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo19_reg: LDO19 {
+					regulator-name = "PVDD_TFLASH_2V8";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+				};
+
+				ldo20_reg: LDO20 {
+					regulator-name = "PVDD_BTWIFI_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo21_reg: LDO21 {
+					regulator-name = "PVDD_CAM1IO_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo23_reg: LDO23 {
+					regulator-name = "PVDD_MIFS_1V1";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				ldo24_reg: LDO24 {
+					regulator-name = "PVDD_CAM1_AVDD_2V8";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+				};
+
+				ldo26_reg: LDO26 {
+					regulator-name = "PVDD_CAM0_AF_2V8";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+				};
+
+				ldo27_reg: LDO27 {
+					regulator-name = "PVDD_G3DS_1V0";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				ldo28_reg: LDO28 {
+					regulator-name = "PVDD_TSP_3V3";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				ldo29_reg: LDO29 {
+					regulator-name = "PVDD_AUDIO_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo31_reg: LDO31 {
+					regulator-name = "PVDD_PERI_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo32_reg: LDO32 {
+					regulator-name = "PVDD_LCD_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo33_reg: LDO33 {
+					regulator-name = "PVDD_CAM0IO_1V8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo35_reg: LDO35 {
+					regulator-name = "PVDD_CAM0_DVDD_1V2";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				ldo38_reg: LDO38 {
+					regulator-name = "PVDD_CAM0_AVDD_2V8";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+				};
+
+				buck1_reg: BUCK1 {
+					regulator-name = "PVDD_MIF_1V1";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+				};
+
+				buck2_reg: BUCK2 {
+					regulator-name = "vdd_arm";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+				};
+
+				buck3_reg: BUCK3 {
+					regulator-name = "PVDD_INT_1V0";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+				};
+
+				buck4_reg: BUCK4 {
+					regulator-name = "PVDD_G3D_1V0";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1000000>;
+				};
+
+				buck5_reg: BUCK5 {
+					regulator-name = "PVDD_LPDDR3_1V2";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				buck6_reg: BUCK6 {
+					regulator-name = "PVDD_KFC_1V0";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+				};
+
+				buck7_reg: BUCK7 {
+					regulator-name = "VIN_LLDO_1V4";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1400000>;
+					regulator-always-on;
+				};
+
+				buck8_reg: BUCK8 {
+					regulator-name = "VIN_MLDO_2V0";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <2000000>;
+					regulator-always-on;
+				};
+
+				buck9_reg: BUCK9 {
+					regulator-name = "VIN_HLDO_3V5";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3500000>;
+					regulator-always-on;
+				};
+
+				buck10_reg: BUCK10 {
+					regulator-name = "PVDD_EMMCF_2V8";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+				};
+			};
+		};
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+
+		wakeup {
+			label = "SW-TACT1";
+			gpios = <&gpx2 7 1>;
+			linux,code = <KEY_WAKEUP>;
+			gpio-key,wakeup;
+		};
+	};
 };

arch/arm/boot/dts/exynos5420-smdk5420.dts

@@ -31,6 +31,43 @@
 		};
 	};
 
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vdd: fixed-regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "vdd-supply";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		dbvdd: fixed-regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "dbvdd-supply";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		spkvdd: fixed-regulator@2 {
+			compatible = "regulator-fixed";
+			reg = <2>;
+			regulator-name = "spkvdd-supply";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			regulator-always-on;
+		};
+	};
+
+	rtc@101E0000 {
+		status = "okay";
+	};
+
 	mmc@12200000 {
 		status = "okay";
 		broken-cd;
@@ -120,4 +157,220 @@
 			reg = <0x50>;
 		};
 	};
+
+	hsi2c_4: i2c@12CA0000 {
+		status = "okay";
+
+		s2mps11_pmic@66 {
+			compatible = "samsung,s2mps11-pmic";
+			reg = <0x66>;
+			s2mps11,buck2-ramp-delay = <12>;
+			s2mps11,buck34-ramp-delay = <12>;
+			s2mps11,buck16-ramp-delay = <12>;
+			s2mps11,buck6-ramp-enable = <1>;
+			s2mps11,buck2-ramp-enable = <1>;
+			s2mps11,buck3-ramp-enable = <1>;
+			s2mps11,buck4-ramp-enable = <1>;
+
+			s2mps11_osc: clocks {
+				#clock-cells = <1>;
+				clock-output-names = "s2mps11_ap",
+						"s2mps11_cp", "s2mps11_bt";
+			};
+
+			regulators {
+				ldo1_reg: LDO1 {
+					regulator-name = "vdd_ldo1";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+				};
+
+				ldo3_reg: LDO3 {
+					regulator-name = "vdd_ldo3";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo5_reg: LDO5 {
+					regulator-name = "vdd_ldo5";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo6_reg: LDO6 {
+					regulator-name = "vdd_ldo6";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+				};
+
+				ldo7_reg: LDO7 {
+					regulator-name = "vdd_ldo7";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo8_reg: LDO8 {
+					regulator-name = "vdd_ldo8";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo9_reg: LDO9 {
+					regulator-name = "vdd_ldo9";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-always-on;
+				};
+
+				ldo10_reg: LDO10 {
+					regulator-name = "vdd_ldo10";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo11_reg: LDO11 {
+					regulator-name = "vdd_ldo11";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+				};
+
+				ldo12_reg: LDO12 {
+					regulator-name = "vdd_ldo12";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				ldo13_reg: LDO13 {
+					regulator-name = "vdd_ldo13";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+				};
+
+				ldo15_reg: LDO15 {
+					regulator-name = "vdd_ldo15";
+					regulator-min-microvolt = <3100000>;
+					regulator-max-microvolt = <3100000>;
+					regulator-always-on;
+				};
+
+				ldo16_reg: LDO16 {
+					regulator-name = "vdd_ldo16";
+					regulator-min-microvolt = <2200000>;
+					regulator-max-microvolt = <2200000>;
+					regulator-always-on;
+				};
+
+				ldo17_reg: LDO17 {
+					regulator-name = "tsp_avdd";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				ldo19_reg: LDO19 {
+					regulator-name = "vdd_sd";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+				};
+
+				ldo24_reg: LDO24 {
+					regulator-name = "tsp_io";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+				};
+
+				buck1_reg: BUCK1 {
+					regulator-name = "vdd_mif";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck2_reg: BUCK2 {
+					regulator-name = "vdd_arm";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1500000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck3_reg: BUCK3 {
+					regulator-name = "vdd_int";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1400000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck4_reg: BUCK4 {
+					regulator-name = "vdd_g3d";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1400000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck5_reg: BUCK5 {
+					regulator-name = "vdd_mem";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1400000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck6_reg: BUCK6 {
+					regulator-name = "vdd_kfc";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1500000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck7_reg: BUCK7 {
+					regulator-name = "vdd_1.0v_ldo";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1500000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck8_reg: BUCK8 {
+					regulator-name = "vdd_1.8v_ldo";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1500000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck9_reg: BUCK9 {
+					regulator-name = "vdd_2.8v_ldo";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3750000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				buck10_reg: BUCK10 {
+					regulator-name = "vdd_vmem";
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+			};
+		};
+	};
 };

arch/arm/boot/dts/exynos5420.dtsi

@@ -13,6 +13,7 @@
  * published by the Free Software Foundation.
  */
 
+#include <dt-bindings/clock/exynos5420.h>
 #include "exynos5.dtsi"
 #include "exynos5420-pinctrl.dtsi"
 
@@ -119,7 +120,8 @@
 		compatible = "samsung,exynos5420-audss-clock";
 		reg = <0x03810000 0x0C>;
 		#clock-cells = <1>;
-		clocks = <&clock 1>, <&clock 5>, <&clock 148>, <&clock 149>;
+		clocks = <&clock CLK_FIN_PLL>, <&clock CLK_FOUT_EPLL>,
+			 <&clock CLK_SCLK_MAUDIO0>, <&clock CLK_SCLK_MAUPCM0>;
 		clock-names = "pll_ref", "pll_in", "sclk_audio", "sclk_pcm_in";
 	};
 
@@ -127,7 +129,7 @@
 		compatible = "samsung,mfc-v7";
 		reg = <0x11000000 0x10000>;
 		interrupts = <0 96 0>;
-		clocks = <&clock 401>;
+		clocks = <&clock CLK_MFC>;
 		clock-names = "mfc";
 	};
 
@@ -137,7 +139,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0x12200000 0x2000>;
-		clocks = <&clock 351>, <&clock 132>;
+		clocks = <&clock CLK_MMC0>, <&clock CLK_SCLK_MMC0>;
 		clock-names = "biu", "ciu";
 		fifo-depth = <0x40>;
 		status = "disabled";
@@ -149,7 +151,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0x12210000 0x2000>;
-		clocks = <&clock 352>, <&clock 133>;
+		clocks = <&clock CLK_MMC1>, <&clock CLK_SCLK_MMC1>;
 		clock-names = "biu", "ciu";
 		fifo-depth = <0x40>;
 		status = "disabled";
@@ -161,7 +163,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0x12220000 0x1000>;
-		clocks = <&clock 353>, <&clock 134>;
+		clocks = <&clock CLK_MMC2>, <&clock CLK_SCLK_MMC2>;
 		clock-names = "biu", "ciu";
 		fifo-depth = <0x40>;
 		status = "disabled";
@@ -175,7 +177,7 @@
 		interrupt-parent = <&mct_map>;
 		interrupts = <0>, <1>, <2>, <3>, <4>, <5>, <6>, <7>,
 				<8>, <9>, <10>, <11>;
-		clocks = <&clock 1>, <&clock 315>;
+		clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>;
 		clock-names = "fin_pll", "mct";
 
 		mct_map: mct-map {
@@ -269,9 +271,9 @@
 	};
 
 	rtc@101E0000 {
-		clocks = <&clock 317>;
+		clocks = <&clock CLK_RTC>;
 		clock-names = "rtc";
-		status = "okay";
+		status = "disabled";
 	};
 
 	amba {
@@ -281,11 +283,22 @@
 		interrupt-parent = <&gic>;
 		ranges;
 
+		adma: adma@03880000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x03880000 0x1000>;
+			interrupts = <0 110 0>;
+			clocks = <&clock_audss EXYNOS_ADMA>;
+			clock-names = "apb_pclk";
+			#dma-cells = <1>;
+			#dma-channels = <6>;
+			#dma-requests = <16>;
+		};
+
 		pdma0: pdma@121A0000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121A0000 0x1000>;
 			interrupts = <0 34 0>;
-			clocks = <&clock 362>;
+			clocks = <&clock CLK_PDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
 			#dma-channels = <8>;
@@ -296,7 +309,7 @@
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121B0000 0x1000>;
 			interrupts = <0 35 0>;
-			clocks = <&clock 363>;
+			clocks = <&clock CLK_PDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
 			#dma-channels = <8>;
@@ -307,7 +320,7 @@
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x10800000 0x1000>;
 			interrupts = <0 33 0>;
-			clocks = <&clock 473>;
+			clocks = <&clock CLK_MDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
 			#dma-channels = <8>;
@@ -318,7 +331,7 @@
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x11C10000 0x1000>;
 			interrupts = <0 124 0>;
-			clocks = <&clock 442>;
+			clocks = <&clock CLK_MDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
 			#dma-channels = <8>;
@@ -326,6 +339,49 @@
 		};
 	};
 
+	i2s0: i2s@03830000 {
+		compatible = "samsung,exynos5420-i2s";
+		reg = <0x03830000 0x100>;
+		dmas = <&adma 0
+			&adma 2
+			&adma 1>;
+		dma-names = "tx", "rx", "tx-sec";
+		clocks = <&clock_audss EXYNOS_I2S_BUS>,
+			<&clock_audss EXYNOS_I2S_BUS>,
+			<&clock_audss EXYNOS_SCLK_I2S>;
+		clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
+		samsung,idma-addr = <0x03000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s0_bus>;
+		status = "disabled";
+	};
+
+	i2s1: i2s@12D60000 {
+		compatible = "samsung,exynos5420-i2s";
+		reg = <0x12D60000 0x100>;
+		dmas = <&pdma1 12
+			&pdma1 11>;
+		dma-names = "tx", "rx";
+		clocks = <&clock CLK_I2S1>, <&clock CLK_SCLK_I2S1>;
+		clock-names = "iis", "i2s_opclk0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s1_bus>;
+		status = "disabled";
+	};
+
+	i2s2: i2s@12D70000 {
+		compatible = "samsung,exynos5420-i2s";
+		reg = <0x12D70000 0x100>;
+		dmas = <&pdma0 12
+			&pdma0 11>;
+		dma-names = "tx", "rx";
+		clocks = <&clock CLK_I2S2>, <&clock CLK_SCLK_I2S2>;
+		clock-names = "iis", "i2s_opclk0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s2_bus>;
+		status = "disabled";
+	};
+
 	spi_0: spi@12d20000 {
 		compatible = "samsung,exynos4210-spi";
 		reg = <0x12d20000 0x100>;
@@ -337,7 +393,7 @@
 		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi0_bus>;
-		clocks = <&clock 271>, <&clock 135>;
+		clocks = <&clock CLK_SPI0>, <&clock CLK_SCLK_SPI0>;
 		clock-names = "spi", "spi_busclk0";
 		status = "disabled";
 	};
@@ -353,7 +409,7 @@
 		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi1_bus>;
-		clocks = <&clock 272>, <&clock 136>;
+		clocks = <&clock CLK_SPI1>, <&clock CLK_SCLK_SPI1>;
 		clock-names = "spi", "spi_busclk0";
 		status = "disabled";
 	};
@@ -369,28 +425,28 @@
 		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi2_bus>;
-		clocks = <&clock 273>, <&clock 137>;
+		clocks = <&clock CLK_SPI2>, <&clock CLK_SCLK_SPI2>;
 		clock-names = "spi", "spi_busclk0";
 		status = "disabled";
 	};
 
 	serial@12C00000 {
-		clocks = <&clock 257>, <&clock 128>;
+		clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>;
 		clock-names = "uart", "clk_uart_baud0";
 	};
 
 	serial@12C10000 {
-		clocks = <&clock 258>, <&clock 129>;
+		clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>;
 		clock-names = "uart", "clk_uart_baud0";
 	};
 
 	serial@12C20000 {
-		clocks = <&clock 259>, <&clock 130>;
+		clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
 		clock-names = "uart", "clk_uart_baud0";
 	};
 
 	serial@12C30000 {
-		clocks = <&clock 260>, <&clock 131>;
+		clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>;
 		clock-names = "uart", "clk_uart_baud0";
 	};
 
@@ -399,7 +455,7 @@
 		reg = <0x12dd0000 0x100>;
 		samsung,pwm-outputs = <0>, <1>, <2>, <3>;
 		#pwm-cells = <3>;
-		clocks = <&clock 279>;
+		clocks = <&clock CLK_PWM>;
 		clock-names = "timers";
 	};
 
@@ -410,7 +466,7 @@
 	};
 
 	dp-controller@145B0000 {
-		clocks = <&clock 412>;
+		clocks = <&clock CLK_DP1>;
 		clock-names = "dp";
 		phys = <&dp_phy>;
 		phy-names = "dp";
@@ -418,7 +474,7 @@
 
 	fimd@14400000 {
 		samsung,power-domain = <&disp_pd>;
-		clocks = <&clock 147>, <&clock 421>;
+		clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
 		clock-names = "sclk_fimd", "fimd";
 	};
 
@@ -426,7 +482,7 @@
 		compatible = "samsung,exynos-adc-v2";
 		reg = <0x12D10000 0x100>, <0x10040720 0x4>;
 		interrupts = <0 106 0>;
-		clocks = <&clock 270>;
+		clocks = <&clock CLK_TSADC>;
 		clock-names = "adc";
 		#io-channel-cells = <1>;
 		io-channel-ranges;
@@ -439,7 +495,7 @@
 		interrupts = <0 56 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 261>;
+		clocks = <&clock CLK_I2C0>;
 		clock-names = "i2c";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c0_bus>;
@@ -452,7 +508,7 @@
 		interrupts = <0 57 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 262>;
+		clocks = <&clock CLK_I2C1>;
 		clock-names = "i2c";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c1_bus>;
@@ -465,7 +521,7 @@
 		interrupts = <0 58 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 263>;
+		clocks = <&clock CLK_I2C2>;
 		clock-names = "i2c";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c2_bus>;
@@ -478,7 +534,7 @@
 		interrupts = <0 59 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 264>;
+		clocks = <&clock CLK_I2C3>;
 		clock-names = "i2c";
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c3_bus>;
@@ -493,7 +549,7 @@
 		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c4_hs_bus>;
-		clocks = <&clock 265>;
+		clocks = <&clock CLK_I2C4>;
 		clock-names = "hsi2c";
 		status = "disabled";
 	};
@@ -506,7 +562,7 @@
 		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c5_hs_bus>;
-		clocks = <&clock 266>;
+		clocks = <&clock CLK_I2C5>;
 		clock-names = "hsi2c";
 		status = "disabled";
 	};
@@ -519,7 +575,7 @@
 		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c6_hs_bus>;
-		clocks = <&clock 267>;
+		clocks = <&clock CLK_I2C6>;
 		clock-names = "hsi2c";
 		status = "disabled";
 	};
@@ -532,7 +588,7 @@
 		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c7_hs_bus>;
-		clocks = <&clock 268>;
+		clocks = <&clock CLK_I2C7>;
 		clock-names = "hsi2c";
 		status = "disabled";
 	};
@@ -545,7 +601,7 @@
 		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c8_hs_bus>;
-		clocks = <&clock 281>;
+		clocks = <&clock CLK_I2C8>;
 		clock-names = "hsi2c";
 		status = "disabled";
 	};
@@ -558,7 +614,7 @@
 		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c9_hs_bus>;
-		clocks = <&clock 282>;
+		clocks = <&clock CLK_I2C9>;
 		clock-names = "hsi2c";
 		status = "disabled";
 	};
@@ -571,7 +627,7 @@
 		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&i2c10_hs_bus>;
-		clocks = <&clock 283>;
+		clocks = <&clock CLK_I2C10>;
 		clock-names = "hsi2c";
 		status = "disabled";
 	};
@@ -580,8 +636,9 @@
 		compatible = "samsung,exynos4212-hdmi";
 		reg = <0x14530000 0x70000>;
 		interrupts = <0 95 0>;
-		clocks = <&clock 413>, <&clock 143>, <&clock 768>,
-			<&clock 158>, <&clock 640>;
+		clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>,
+			 <&clock CLK_DOUT_PIXEL>, <&clock CLK_SCLK_HDMIPHY>,
+			 <&clock CLK_MOUT_HDMI>;
 		clock-names = "hdmi", "sclk_hdmi", "sclk_pixel",
 			"sclk_hdmiphy", "mout_hdmi";
 		status = "disabled";
@@ -591,7 +648,7 @@
 		compatible = "samsung,exynos5420-mixer";
 		reg = <0x14450000 0x10000>;
 		interrupts = <0 94 0>;
-		clocks = <&clock 431>, <&clock 143>;
+		clocks = <&clock CLK_MIXER>, <&clock CLK_SCLK_HDMI>;
 		clock-names = "mixer", "sclk_hdmi";
 	};
 
@@ -599,7 +656,7 @@
 		compatible = "samsung,exynos5-gsc";
 		reg = <0x13e00000 0x1000>;
 		interrupts = <0 85 0>;
-		clocks = <&clock 465>;
+		clocks = <&clock CLK_GSCL0>;
 		clock-names = "gscl";
 		samsung,power-domain = <&gsc_pd>;
 	};
@@ -608,16 +665,21 @@
 		compatible = "samsung,exynos5-gsc";
 		reg = <0x13e10000 0x1000>;
 		interrupts = <0 86 0>;
-		clocks = <&clock 466>;
+		clocks = <&clock CLK_GSCL1>;
 		clock-names = "gscl";
 		samsung,power-domain = <&gsc_pd>;
 	};
 
+	pmu_system_controller: system-controller@10040000 {
+		compatible = "samsung,exynos5420-pmu", "syscon";
+		reg = <0x10040000 0x5000>;
+	};
+
 	tmu_cpu0: tmu@10060000 {
 		compatible = "samsung,exynos5420-tmu";
 		reg = <0x10060000 0x100>;
 		interrupts = <0 65 0>;
-		clocks = <&clock 318>;
+		clocks = <&clock CLK_TMU>;
 		clock-names = "tmu_apbif";
 	};
 
@@ -625,7 +687,7 @@
 		compatible = "samsung,exynos5420-tmu";
 		reg = <0x10064000 0x100>;
 		interrupts = <0 183 0>;
-		clocks = <&clock 318>;
+		clocks = <&clock CLK_TMU>;
 		clock-names = "tmu_apbif";
 	};
 
@@ -633,7 +695,7 @@
 		compatible = "samsung,exynos5420-tmu-ext-triminfo";
 		reg = <0x10068000 0x100>, <0x1006c000 0x4>;
 		interrupts = <0 184 0>;
-		clocks = <&clock 318>, <&clock 318>;
+		clocks = <&clock CLK_TMU>, <&clock CLK_TMU>;
 		clock-names = "tmu_apbif", "tmu_triminfo_apbif";
 	};
 
@@ -641,7 +703,7 @@
 		compatible = "samsung,exynos5420-tmu-ext-triminfo";
 		reg = <0x1006c000 0x100>, <0x100a0000 0x4>;
 		interrupts = <0 185 0>;
-		clocks = <&clock 318>, <&clock 319>;
+		clocks = <&clock CLK_TMU>, <&clock CLK_TMU_GPU>;
 		clock-names = "tmu_apbif", "tmu_triminfo_apbif";
 	};
 
@@ -649,7 +711,16 @@
 		compatible = "samsung,exynos5420-tmu-ext-triminfo";
 		reg = <0x100a0000 0x100>, <0x10068000 0x4>;
 		interrupts = <0 215 0>;
-		clocks = <&clock 319>, <&clock 318>;
+		clocks = <&clock CLK_TMU_GPU>, <&clock CLK_TMU>;
 		clock-names = "tmu_apbif", "tmu_triminfo_apbif";
 	};
+
+        watchdog@101D0000 {
+		compatible = "samsung,exynos5420-wdt";
+		reg = <0x101D0000 0x100>;
+		interrupts = <0 42 0>;
+		clocks = <&clock CLK_WDT>;
+		clock-names = "watchdog";
+		samsung,syscon-phandle = <&pmu_system_controller>;
+        };
 };

arch/arm/boot/dts/exynos5440.dtsi

@@ -9,6 +9,7 @@
  * published by the Free Software Foundation.
 */
 
+#include <dt-bindings/clock/exynos5440.h>
 #include "skeleton.dtsi"
 
 / {
@@ -105,7 +106,7 @@
 		compatible = "samsung,exynos4210-uart";
 		reg = <0xB0000 0x1000>;
 		interrupts = <0 2 0>;
-		clocks = <&clock 21>, <&clock 21>;
+		clocks = <&clock CLK_B_125>, <&clock CLK_B_125>;
 		clock-names = "uart", "clk_uart_baud0";
 	};
 
@@ -113,7 +114,7 @@
 		compatible = "samsung,exynos4210-uart";
 		reg = <0xC0000 0x1000>;
 		interrupts = <0 3 0>;
-		clocks = <&clock 21>, <&clock 21>;
+		clocks = <&clock CLK_B_125>, <&clock CLK_B_125>;
 		clock-names = "uart", "clk_uart_baud0";
 	};
 
@@ -125,7 +126,7 @@
 		#size-cells = <0>;
 		samsung,spi-src-clk = <0>;
 		num-cs = <1>;
-		clocks = <&clock 21>, <&clock 16>;
+		clocks = <&clock CLK_B_125>, <&clock CLK_SPI_BAUD>;
 		clock-names = "spi", "spi_busclk0";
 	};
 
@@ -161,7 +162,7 @@
 		interrupts = <0 5 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 21>;
+		clocks = <&clock CLK_B_125>;
 		clock-names = "i2c";
 	};
 
@@ -171,7 +172,7 @@
 		interrupts = <0 6 0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&clock 21>;
+		clocks = <&clock CLK_B_125>;
 		clock-names = "i2c";
 	};
 
@@ -179,7 +180,7 @@
 		compatible = "samsung,s3c2410-wdt";
 		reg = <0x110000 0x1000>;
 		interrupts = <0 1 0>;
-		clocks = <&clock 21>;
+		clocks = <&clock CLK_B_125>;
 		clock-names = "watchdog";
 	};
 
@@ -190,7 +191,7 @@
 		interrupts = <0 31 4>;
 		interrupt-names = "macirq";
 		phy-mode = "sgmii";
-		clocks = <&clock 25>;
+		clocks = <&clock CLK_GMAC0>;
 		clock-names = "stmmaceth";
 	};
 
@@ -206,7 +207,7 @@
 		compatible = "samsung,s3c6410-rtc";
 		reg = <0x130000 0x1000>;
 		interrupts = <0 17 0>, <0 16 0>;
-		clocks = <&clock 21>;
+		clocks = <&clock CLK_B_125>;
 		clock-names = "rtc";
 	};
 
@@ -214,7 +215,7 @@
 		compatible = "samsung,exynos5440-tmu";
 		reg = <0x160118 0x230>, <0x160368 0x10>;
 		interrupts = <0 58 0>;
-		clocks = <&clock 21>;
+		clocks = <&clock CLK_B_125>;
 		clock-names = "tmu_apbif";
 	};
 
@@ -222,7 +223,7 @@
 		compatible = "samsung,exynos5440-tmu";
 		reg = <0x16011C 0x230>, <0x160368 0x10>;
 		interrupts = <0 58 0>;
-		clocks = <&clock 21>;
+		clocks = <&clock CLK_B_125>;
 		clock-names = "tmu_apbif";
 	};
 
@@ -230,7 +231,7 @@
 		compatible = "samsung,exynos5440-tmu";
 		reg = <0x160120 0x230>, <0x160368 0x10>;
 		interrupts = <0 58 0>;
-		clocks = <&clock 21>;
+		clocks = <&clock CLK_B_125>;
 		clock-names = "tmu_apbif";
 	};
 
@@ -238,7 +239,7 @@
 		compatible = "snps,exynos5440-ahci";
 		reg = <0x210000 0x10000>;
 		interrupts = <0 30 0>;
-		clocks = <&clock 23>;
+		clocks = <&clock CLK_SATA>;
 		clock-names = "sata";
 	};
 
@@ -246,7 +247,7 @@
 		compatible = "samsung,exynos5440-ohci";
 		reg = <0x220000 0x1000>;
 		interrupts = <0 29 0>;
-		clocks = <&clock 24>;
+		clocks = <&clock CLK_USB>;
 		clock-names = "usbhost";
 	};
 
@@ -254,7 +255,7 @@
 		compatible = "samsung,exynos5440-ehci";
 		reg = <0x221000 0x1000>;
 		interrupts = <0 29 0>;
-		clocks = <&clock 24>;
+		clocks = <&clock CLK_USB>;
 		clock-names = "usbhost";
 	};
 
@@ -264,7 +265,7 @@
 			0x270000 0x1000
 			0x271000 0x40>;
 		interrupts = <0 20 0>, <0 21 0>, <0 22 0>;
-		clocks = <&clock 28>, <&clock 27>;
+		clocks = <&clock CLK_PR0_250_O>, <&clock CLK_PB0_250_O>;
 		clock-names = "pcie", "pcie_bus";
 		#address-cells = <3>;
 		#size-cells = <2>;
@@ -285,7 +286,7 @@
 			0x272000 0x1000
 			0x271040 0x40>;
 		interrupts = <0 23 0>, <0 24 0>, <0 25 0>;
-		clocks = <&clock 29>, <&clock 27>;
+		clocks = <&clock CLK_PR1_250_O>, <&clock CLK_PB0_250_O>;
 		clock-names = "pcie", "pcie_bus";
 		#address-cells = <3>;
 		#size-cells = <2>;

arch/arm/boot/dts/imx23-evk.dts

@@ -127,17 +127,21 @@
 
 	regulators {
 		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		reg_vddio_sd0: vddio-sd0 {
+		reg_vddio_sd0: regulator@0 {
 			compatible = "regulator-fixed";
+			reg = <0>;
 			regulator-name = "vddio-sd0";
 			regulator-min-microvolt = <3300000>;
 			regulator-max-microvolt = <3300000>;
 			gpio = <&gpio1 29 0>;
 		};
 
-		reg_lcd_3v3: lcd-3v3 {
+		reg_lcd_3v3: regulator@1 {
 			compatible = "regulator-fixed";
+			reg = <1>;
 			regulator-name = "lcd-3v3";
 			regulator-min-microvolt = <3300000>;
 			regulator-max-microvolt = <3300000>;

arch/arm/boot/dts/imx23-olinuxino.dts

@@ -100,9 +100,12 @@
 
 	regulators {
 		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		reg_usb0_vbus: usb0_vbus {
+		reg_usb0_vbus: regulator@0 {
 			compatible = "regulator-fixed";
+			reg = <0>;
 			regulator-name = "usb0_vbus";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;

arch/arm/boot/dts/imx23-stmp378x_devb.dts

@@ -66,9 +66,12 @@
 
 	regulators {
 		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		reg_vddio_sd0: vddio-sd0 {
+		reg_vddio_sd0: regulator@0 {
 			compatible = "regulator-fixed";
+			reg = <0>;
 			regulator-name = "vddio-sd0";
 			regulator-min-microvolt = <3300000>;
 			regulator-max-microvolt = <3300000>;

arch/arm/boot/dts/imx23.dtsi

@@ -23,6 +23,7 @@
 		serial1 = &auart1;
 		spi0 = &ssp0;
 		spi1 = &ssp1;
+		usbphy0 = &usbphy0;
 	};
 
 	cpus {
@@ -428,7 +429,7 @@
 				status = "disabled";
 			};
 
-			lradc@80050000 {
+			lradc: lradc@80050000 {
 				compatible = "fsl,imx23-lradc";
 				reg = <0x80050000 0x2000>;
 				interrupts = <36 37 38 39 40 41 42 43 44>;
@@ -526,4 +527,9 @@
 			status = "disabled";
 		};
 	};
+
+	iio_hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&lradc 8>;
+	};
 };

arch/arm/boot/dts/imx25-eukrea-cpuimx25.dtsi

@@ -0,0 +1,73 @@
+/*
+ * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include "imx25.dtsi"
+
+/ {
+	model = "Eukrea CPUIMX25";
+	compatible = "eukrea,cpuimx25", "fsl,imx25";
+
+	memory {
+		reg = <0x80000000 0x4000000>; /* 64M */
+	};
+};
+
+&fec {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&iomuxc {
+	imx25-eukrea-cpuimx25 {
+		pinctrl_fec: fecgrp {
+			fsl,pins = <
+				MX25_PAD_FEC_MDC__FEC_MDC		0x80000000
+				MX25_PAD_FEC_MDIO__FEC_MDIO		0x400001e0
+				MX25_PAD_FEC_TDATA0__FEC_TDATA0		0x80000000
+				MX25_PAD_FEC_TDATA1__FEC_TDATA1		0x80000000
+				MX25_PAD_FEC_TX_EN__FEC_TX_EN		0x80000000
+				MX25_PAD_FEC_RDATA0__FEC_RDATA0		0x80000000
+				MX25_PAD_FEC_RDATA1__FEC_RDATA1		0x80000000
+				MX25_PAD_FEC_RX_DV__FEC_RX_DV		0x80000000
+				MX25_PAD_FEC_TX_CLK__FEC_TX_CLK		0x1c0
+			>;
+		};
+
+		pinctrl_i2c1: i2c1grp {
+			fsl,pins = <
+				MX25_PAD_I2C1_CLK__I2C1_CLK		0x80000000
+				MX25_PAD_I2C1_DAT__I2C1_DAT		0x80000000
+			>;
+		};
+	};
+};
+
+&nfc {
+	nand-bus-width = <8>;
+	nand-ecc-mode = "hw";
+	nand-on-flash-bbt;
+	status = "okay";
+};

arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dts

@@ -0,0 +1,174 @@
+/*
+ * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "imx25-eukrea-cpuimx25.dtsi"
+
+/ {
+	model = "Eukrea MBIMXSD25";
+	compatible = "eukrea,mbimxsd25-baseboard", "eukrea,cpuimx25", "fsl,imx25";
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiokeys>;
+
+		bp1 {
+			label = "BP1";
+			gpios = <&gpio3 18 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_MISC>;
+			gpio-key,wakeup;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpioled>;
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	sound {
+		compatible = "eukrea,asoc-tlv320";
+		eukrea,model = "imx25-eukrea-tlv320aic23";
+		ssi-controller = <&ssi1>;
+		fsl,mux-int-port = <1>;
+		fsl,mux-ext-port = <5>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&esdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_esdhc1>;
+	cd-gpios = <&gpio1 20>;
+	status = "okay";
+};
+
+&i2c1 {
+	tlv320aic23: codec@1a {
+		compatible = "ti,tlv320aic23";
+		reg = <0x1a>;
+	};
+};
+
+&iomuxc {
+	imx25-eukrea-mbimxsd25-baseboard {
+		pinctrl_audmux: audmuxgrp {
+			fsl,pins = <
+				MX25_PAD_KPP_COL3__AUD5_TXFS		0xe0
+				MX25_PAD_KPP_COL2__AUD5_TXC		0xe0
+				MX25_PAD_KPP_COL1__AUD5_RXD		0xe0
+				MX25_PAD_KPP_COL0__AUD5_TXD		0xe0
+			>;
+		};
+
+		pinctrl_esdhc1: esdhc1grp {
+			fsl,pins = <
+				MX25_PAD_SD1_CMD__SD1_CMD		0x400000c0
+				MX25_PAD_SD1_CLK__SD1_CLK		0x400000c0
+				MX25_PAD_SD1_DATA0__SD1_DATA0		0x400000c0
+				MX25_PAD_SD1_DATA1__SD1_DATA1		0x400000c0
+				MX25_PAD_SD1_DATA2__SD1_DATA2		0x400000c0
+				MX25_PAD_SD1_DATA3__SD1_DATA3		0x400000c0
+			>;
+		};
+
+		pinctrl_gpiokeys: gpiokeysgrp {
+			fsl,pins = <MX25_PAD_VSTBY_ACK__GPIO_3_18 0x80000000>;
+		};
+
+		pinctrl_gpioled: gpioledgrp {
+			fsl,pins = <MX25_PAD_POWER_FAIL__GPIO_3_19 0x80000000>;
+		};
+
+		pinctrl_lcdc: lcdcgrp {
+			fsl,pins = <
+				MX25_PAD_LD0__LD0			0x1
+				MX25_PAD_LD1__LD1			0x1
+				MX25_PAD_LD2__LD2			0x1
+				MX25_PAD_LD3__LD3			0x1
+				MX25_PAD_LD4__LD4			0x1
+				MX25_PAD_LD5__LD5			0x1
+				MX25_PAD_LD6__LD6			0x1
+				MX25_PAD_LD7__LD7			0x1
+				MX25_PAD_LD8__LD8			0x1
+				MX25_PAD_LD9__LD9			0x1
+				MX25_PAD_LD10__LD10			0x1
+				MX25_PAD_LD11__LD11			0x1
+				MX25_PAD_LD12__LD12			0x1
+				MX25_PAD_LD13__LD13			0x1
+				MX25_PAD_LD14__LD14			0x1
+				MX25_PAD_LD15__LD15			0x1
+				MX25_PAD_GPIO_E__LD16			0x1
+				MX25_PAD_GPIO_F__LD17			0x1
+				MX25_PAD_HSYNC__HSYNC			0x80000000
+				MX25_PAD_VSYNC__VSYNC			0x80000000
+				MX25_PAD_LSCLK__LSCLK			0x80000000
+				MX25_PAD_OE_ACD__OE_ACD			0x80000000
+				MX25_PAD_CONTRAST__CONTRAST		0x80000000
+			>;
+		};
+
+		pinctrl_uart1: uart1grp {
+			fsl,pins = <
+				MX25_PAD_UART1_RTS__UART1_RTS		0xe0
+				MX25_PAD_UART1_CTS__UART1_CTS		0xe0
+				MX25_PAD_UART1_TXD__UART1_TXD		0x80000000
+				MX25_PAD_UART1_RXD__UART1_RXD		0xc0
+			>;
+		};
+
+		pinctrl_uart2: uart2grp {
+			fsl,pins = <
+				MX25_PAD_UART2_RXD__UART2_RXD		0x80000000
+				MX25_PAD_UART2_TXD__UART2_TXD		0x80000000
+				MX25_PAD_UART2_RTS__UART2_RTS		0x80000000
+				MX25_PAD_UART2_CTS__UART2_CTS		0x80000000
+			>;
+		};
+	};
+};
+
+&ssi1 {
+	codec-handle = <&tlv320aic23>;
+	fsl,mode = "i2s-slave";
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	fsl,uart-has-rtscts;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	fsl,uart-has-rtscts;
+	status = "okay";
+};

arch/arm/boot/dts/imx25-pinfunc.h

@@ -0,0 +1,494 @@
+/*
+ * Copyright 2013 Eukréa Electromatique <denis@eukrea.com>
+ * Based on imx35-pinfunc.h in the same directory Which is:
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef __DTS_IMX25_PINFUNC_H
+#define __DTS_IMX25_PINFUNC_H
+
+/*
+ * The pin function ID is a tuple of
+ * <mux_reg conf_reg input_reg mux_mode input_val>
+ */
+
+#define MX25_PAD_A10__A10			0x008 0x000 0x000 0x00 0x000
+#define MX25_PAD_A10__GPIO_4_0			0x008 0x000 0x000 0x05 0x000
+
+#define MX25_PAD_A13__A13			0x00c 0x22C 0x000 0x00 0x000
+#define MX25_PAD_A13__GPIO_4_1			0x00c 0x22C 0x000 0x05 0x000
+
+#define MX25_PAD_A14__A14			0x010 0x230 0x000 0x10 0x000
+#define MX25_PAD_A14__GPIO_2_0			0x010 0x230 0x000 0x15 0x000
+
+#define MX25_PAD_A15__A15			0x014 0x234 0x000 0x10 0x000
+#define MX25_PAD_A15__GPIO_2_1			0x014 0x234 0x000 0x15 0x000
+
+#define MX25_PAD_A16__A16			0x018 0x000 0x000 0x10 0x000
+#define MX25_PAD_A16__GPIO_2_2			0x018 0x000 0x000 0x15 0x000
+
+#define MX25_PAD_A17__A17			0x01c 0x238 0x000 0x10 0x000
+#define MX25_PAD_A17__GPIO_2_3			0x01c 0x238 0x000 0x15 0x000
+
+#define MX25_PAD_A18__A18			0x020 0x23c 0x000 0x10 0x000
+#define MX25_PAD_A18__GPIO_2_4			0x020 0x23c 0x000 0x15 0x000
+#define MX25_PAD_A18__FEC_COL			0x020 0x23c 0x504 0x17 0x000
+
+#define MX25_PAD_A19__A19			0x024 0x240 0x000 0x10 0x000
+#define MX25_PAD_A19__FEC_RX_ER			0x024 0x240 0x518 0x17 0x000
+#define MX25_PAD_A19__GPIO_2_5			0x024 0x240 0x000 0x15 0x000
+
+#define MX25_PAD_A20__A20			0x028 0x244 0x000 0x10 0x000
+#define MX25_PAD_A20__GPIO_2_6			0x028 0x244 0x000 0x15 0x000
+#define MX25_PAD_A20__FEC_RDATA2		0x028 0x244 0x50c 0x17 0x000
+
+#define MX25_PAD_A21__A21			0x02c 0x248 0x000 0x10 0x000
+#define MX25_PAD_A21__GPIO_2_7			0x02c 0x248 0x000 0x15 0x000
+#define MX25_PAD_A21__FEC_RDATA3		0x02c 0x248 0x510 0x17 0x000
+
+#define MX25_PAD_A22__A22			0x030 0x000 0x000 0x10 0x000
+#define MX25_PAD_A22__GPIO_2_8			0x030 0x000 0x000 0x15 0x000
+
+#define MX25_PAD_A23__A23			0x034 0x24c 0x000 0x10 0x000
+#define MX25_PAD_A23__GPIO_2_9			0x034 0x24c 0x000 0x15 0x000
+
+#define MX25_PAD_A24__A24			0x038 0x250 0x000 0x10 0x000
+#define MX25_PAD_A24__GPIO_2_10			0x038 0x250 0x000 0x15 0x000
+#define MX25_PAD_A24__FEC_RX_CLK		0x038 0x250 0x514 0x17 0x000
+
+#define MX25_PAD_A25__A25			0x03c 0x254 0x000 0x10 0x000
+#define MX25_PAD_A25__GPIO_2_11			0x03c 0x254 0x000 0x15 0x000
+#define MX25_PAD_A25__FEC_CRS			0x03c 0x254 0x508 0x17 0x000
+
+#define MX25_PAD_EB0__EB0			0x040 0x258 0x000 0x10 0x000
+#define MX25_PAD_EB0__AUD4_TXD			0x040 0x258 0x464 0x14 0x000
+#define MX25_PAD_EB0__GPIO_2_12			0x040 0x258 0x000 0x15 0x000
+
+#define MX25_PAD_EB1__EB1			0x044 0x25c 0x000 0x10 0x000
+#define MX25_PAD_EB1__AUD4_RXD			0x044 0x25c 0x460 0x14 0x000
+#define MX25_PAD_EB1__GPIO_2_13			0x044 0x25c 0x000 0x15 0x000
+
+#define MX25_PAD_OE__OE				0x048 0x260 0x000 0x10 0x000
+#define MX25_PAD_OE__AUD4_TXC			0x048 0x260 0x000 0x14 0x000
+#define MX25_PAD_OE__GPIO_2_14			0x048 0x260 0x000 0x15 0x000
+
+#define MX25_PAD_CS0__CS0			0x04c 0x000 0x000 0x00 0x000
+#define MX25_PAD_CS0__GPIO_4_2			0x04c 0x000 0x000 0x05 0x000
+
+#define MX25_PAD_CS1__CS1			0x050 0x000 0x000 0x00 0x000
+#define MX25_PAD_CS1__NF_CE3			0x050 0x000 0x000 0x01 0x000
+#define MX25_PAD_CS1__GPIO_4_3			0x050 0x000 0x000 0x05 0x000
+
+#define MX25_PAD_CS4__CS4			0x054 0x264 0x000 0x10 0x000
+#define MX25_PAD_CS4__NF_CE1			0x054 0x264 0x000 0x01 0x000
+#define MX25_PAD_CS4__UART5_CTS			0x054 0x264 0x000 0x13 0x000
+#define MX25_PAD_CS4__GPIO_3_20			0x054 0x264 0x000 0x15 0x000
+
+#define MX25_PAD_CS5__CS5			0x058 0x268 0x000 0x10 0x000
+#define MX25_PAD_CS5__NF_CE2			0x058 0x268 0x000 0x01 0x000
+#define MX25_PAD_CS5__UART5_RTS			0x058 0x268 0x574 0x13 0x000
+#define MX25_PAD_CS5__GPIO_3_21			0x058 0x268 0x000 0x15 0x000
+
+#define MX25_PAD_NF_CE0__NF_CE0			0x05c 0x26c 0x000 0x10 0x000
+#define MX25_PAD_NF_CE0__GPIO_3_22		0x05c 0x26c 0x000 0x15 0x000
+
+#define MX25_PAD_ECB__ECB			0x060 0x270 0x000 0x10 0x000
+#define MX25_PAD_ECB__UART5_TXD_MUX		0x060 0x270 0x000 0x13 0x000
+#define MX25_PAD_ECB__GPIO_3_23			0x060 0x270 0x000 0x15 0x000
+
+#define MX25_PAD_LBA__LBA			0x064 0x274 0x000 0x10 0x000
+#define MX25_PAD_LBA__UART5_RXD_MUX		0x064 0x274 0x578 0x13 0x000
+#define MX25_PAD_LBA__GPIO_3_24			0x064 0x274 0x000 0x15 0x000
+
+#define MX25_PAD_BCLK__BCLK			0x068 0x000 0x000 0x00 0x000
+#define MX25_PAD_BCLK__GPIO_4_4			0x068 0x000 0x000 0x05 0x000
+
+#define MX25_PAD_RW__RW				0x06c 0x278 0x000 0x10 0x000
+#define MX25_PAD_RW__AUD4_TXFS			0x06c 0x278 0x474 0x14 0x000
+#define MX25_PAD_RW__GPIO_3_25			0x06c 0x278 0x000 0x15 0x000
+
+#define MX25_PAD_NFWE_B__NFWE_B			0x070 0x000 0x000 0x10 0x000
+#define MX25_PAD_NFWE_B__GPIO_3_26		0x070 0x000 0x000 0x15 0x000
+
+#define MX25_PAD_NFRE_B__NFRE_B			0x074 0x000 0x000 0x10 0x000
+#define MX25_PAD_NFRE_B__GPIO_3_27		0x074 0x000 0x000 0x15 0x000
+
+#define MX25_PAD_NFALE__NFALE			0x078 0x000 0x000 0x10 0x000
+#define MX25_PAD_NFALE__GPIO_3_28		0x078 0x000 0x000 0x15 0x000
+
+#define MX25_PAD_NFCLE__NFCLE			0x07c 0x000 0x000 0x10 0x000
+#define MX25_PAD_NFCLE__GPIO_3_29		0x07c 0x000 0x000 0x15 0x000
+
+#define MX25_PAD_NFWP_B__NFWP_B			0x080 0x000 0x000 0x10 0x000
+#define MX25_PAD_NFWP_B__GPIO_3_30		0x080 0x000 0x000 0x15 0x000
+
+#define MX25_PAD_NFRB__NFRB			0x084 0x27c 0x000 0x10 0x000
+#define MX25_PAD_NFRB__GPIO_3_31		0x084 0x27c 0x000 0x15 0x000
+
+#define MX25_PAD_D15__D15			0x088 0x280 0x000 0x00 0x000
+#define MX25_PAD_D15__LD16			0x088 0x280 0x000 0x01 0x000
+#define MX25_PAD_D15__GPIO_4_5			0x088 0x280 0x000 0x05 0x000
+
+#define MX25_PAD_D14__D14			0x08c 0x284 0x000 0x00 0x000
+#define MX25_PAD_D14__LD17			0x08c 0x284 0x000 0x01 0x000
+#define MX25_PAD_D14__GPIO_4_6			0x08c 0x284 0x000 0x05 0x000
+
+#define MX25_PAD_D13__D13			0x090 0x288 0x000 0x00 0x000
+#define MX25_PAD_D13__LD18			0x090 0x288 0x000 0x01 0x000
+#define MX25_PAD_D13__GPIO_4_7			0x090 0x288 0x000 0x05 0x000
+
+#define MX25_PAD_D12__D12			0x094 0x28c 0x000 0x00 0x000
+#define MX25_PAD_D12__GPIO_4_8			0x094 0x28c 0x000 0x05 0x000
+
+#define MX25_PAD_D11__D11			0x098 0x290 0x000 0x00 0x000
+#define MX25_PAD_D11__GPIO_4_9			0x098 0x290 0x000 0x05 0x000
+
+#define MX25_PAD_D10__D10			0x09c 0x294 0x000 0x00 0x000
+#define MX25_PAD_D10__GPIO_4_10			0x09c 0x294 0x000 0x05 0x000
+#define MX25_PAD_D10__USBOTG_OC			0x09c 0x294 0x57c 0x06 0x000
+
+#define MX25_PAD_D9__D9				0x0a0 0x298 0x000 0x00 0x000
+#define MX25_PAD_D9__GPIO_4_11			0x0a0 0x298 0x000 0x05 0x000
+#define MX25_PAD_D9__USBH2_PWR			0x0a0 0x298 0x000 0x06 0x000
+
+#define MX25_PAD_D8__D8				0x0a4 0x29c 0x000 0x00 0x000
+#define MX25_PAD_D8__GPIO_4_12			0x0a4 0x29c 0x000 0x05 0x000
+#define MX25_PAD_D8__USBH2_OC			0x0a4 0x29c 0x580 0x06 0x000
+
+#define MX25_PAD_D7__D7				0x0a8 0x2a0 0x000 0x00 0x000
+#define MX25_PAD_D7__GPIO_4_13			0x0a8 0x2a0 0x000 0x05 0x000
+
+#define MX25_PAD_D6__D6				0x0ac 0x2a4 0x000 0x00 0x000
+#define MX25_PAD_D6__GPIO_4_14			0x0ac 0x2a4 0x000 0x05 0x000
+
+#define MX25_PAD_D5__D5				0x0b0 0x2a8 0x000 0x00 0x000
+#define MX25_PAD_D5__GPIO_4_15			0x0b0 0x2a8 0x000 0x05 0x000
+
+#define MX25_PAD_D4__D4				0x0b4 0x2ac 0x000 0x00 0x000
+#define MX25_PAD_D4__GPIO_4_16			0x0b4 0x2ac 0x000 0x05 0x000
+
+#define MX25_PAD_D3__D3				0x0b8 0x2b0 0x000 0x00 0x000
+#define MX25_PAD_D3__GPIO_4_17			0x0b8 0x2b0 0x000 0x05 0x000
+
+#define MX25_PAD_D2__D2				0x0bc 0x2b4 0x000 0x00 0x000
+#define MX25_PAD_D2__GPIO_4_18			0x0bc 0x2b4 0x000 0x05 0x000
+
+#define MX25_PAD_D1__D1				0x0c0 0x2b8 0x000 0x00 0x000
+#define MX25_PAD_D1__GPIO_4_19			0x0c0 0x2b8 0x000 0x05 0x000
+
+#define MX25_PAD_D0__D0				0x0c4 0x2bc 0x000 0x00 0x000
+#define MX25_PAD_D0__GPIO_4_20			0x0c4 0x2bc 0x000 0x05 0x000
+
+#define MX25_PAD_LD0__LD0			0x0c8 0x2c0 0x000 0x10 0x000
+#define MX25_PAD_LD0__CSI_D0			0x0c8 0x2c0 0x488 0x12 0x000
+#define MX25_PAD_LD0__GPIO_2_15			0x0c8 0x2c0 0x000 0x15 0x000
+
+#define MX25_PAD_LD1__LD1			0x0cc 0x2c4 0x000 0x10 0x000
+#define MX25_PAD_LD1__CSI_D1			0x0cc 0x2c4 0x48c 0x12 0x000
+#define MX25_PAD_LD1__GPIO_2_16			0x0cc 0x2c4 0x000 0x15 0x000
+
+#define MX25_PAD_LD2__LD2			0x0d0 0x2c8 0x000 0x10 0x000
+#define MX25_PAD_LD2__GPIO_2_17			0x0d0 0x2c8 0x000 0x15 0x000
+
+#define MX25_PAD_LD3__LD3			0x0d4 0x2cc 0x000 0x10 0x000
+#define MX25_PAD_LD3__GPIO_2_18			0x0d4 0x2cc 0x000 0x15 0x000
+
+#define MX25_PAD_LD4__LD4			0x0d8 0x2d0 0x000 0x10 0x000
+#define MX25_PAD_LD4__GPIO_2_19			0x0d8 0x2d0 0x000 0x15 0x000
+
+#define MX25_PAD_LD5__LD5			0x0dc 0x2d4 0x000 0x10 0x000
+#define MX25_PAD_LD5__GPIO_1_19			0x0dc 0x2d4 0x000 0x15 0x000
+
+#define MX25_PAD_LD6__LD6			0x0e0 0x2d8 0x000 0x10 0x000
+#define MX25_PAD_LD6__GPIO_1_20			0x0e0 0x2d8 0x000 0x15 0x000
+
+#define MX25_PAD_LD7__LD7			0x0e4 0x2dc 0x000 0x10 0x000
+#define MX25_PAD_LD7__GPIO_1_21			0x0e4 0x2dc 0x000 0x15 0x000
+
+#define MX25_PAD_LD8__LD8			0x0e8 0x2e0 0x000 0x10 0x000
+#define MX25_PAD_LD8__FEC_TX_ERR		0x0e8 0x2e0 0x000 0x15 0x000
+
+#define MX25_PAD_LD9__LD9			0x0ec 0x2e4 0x000 0x10 0x000
+#define MX25_PAD_LD9__FEC_COL			0x0ec 0x2e4 0x504 0x15 0x001
+
+#define MX25_PAD_LD10__LD10			0x0f0 0x2e8 0x000 0x10 0x000
+#define MX25_PAD_LD10__FEC_RX_ER		0x0f0 0x2e8 0x518 0x15 0x001
+
+#define MX25_PAD_LD11__LD11			0x0f4 0x2ec 0x000 0x10 0x000
+#define MX25_PAD_LD11__FEC_RDATA2		0x0f4 0x2ec 0x50c 0x15 0x001
+
+#define MX25_PAD_LD12__LD12			0x0f8 0x2f0 0x000 0x10 0x000
+#define MX25_PAD_LD12__FEC_RDATA3		0x0f8 0x2f0 0x510 0x15 0x001
+
+#define MX25_PAD_LD13__LD13			0x0fc 0x2f4 0x000 0x10 0x000
+#define MX25_PAD_LD13__FEC_TDATA2		0x0fc 0x2f4 0x000 0x15 0x000
+
+#define MX25_PAD_LD14__LD14			0x100 0x2f8 0x000 0x10 0x000
+#define MX25_PAD_LD14__FEC_TDATA3		0x100 0x2f8 0x000 0x15 0x000
+
+#define MX25_PAD_LD15__LD15			0x104 0x2fc 0x000 0x10 0x000
+#define MX25_PAD_LD15__FEC_RX_CLK		0x104 0x2fc 0x514 0x15 0x001
+
+#define MX25_PAD_HSYNC__HSYNC			0x108 0x300 0x000 0x10 0x000
+#define MX25_PAD_HSYNC__GPIO_1_22		0x108 0x300 0x000 0x15 0x000
+
+#define MX25_PAD_VSYNC__VSYNC			0x10c 0x304 0x000 0x10 0x000
+#define MX25_PAD_VSYNC__GPIO_1_23		0x10c 0x304 0x000 0x15 0x000
+
+#define MX25_PAD_LSCLK__LSCLK			0x110 0x308 0x000 0x10 0x000
+#define MX25_PAD_LSCLK__GPIO_1_24		0x110 0x308 0x000 0x15 0x000
+
+#define MX25_PAD_OE_ACD__OE_ACD			0x114 0x30c 0x000 0x10 0x000
+#define MX25_PAD_OE_ACD__GPIO_1_25		0x114 0x30c 0x000 0x15 0x000
+
+#define MX25_PAD_CONTRAST__CONTRAST		0x118 0x310 0x000 0x10 0x000
+#define MX25_PAD_CONTRAST__PWM4_PWMO		0x118 0x310 0x000 0x14 0x000
+#define MX25_PAD_CONTRAST__FEC_CRS		0x118 0x310 0x508 0x15 0x001
+
+#define MX25_PAD_PWM__PWM			0x11c 0x314 0x000 0x10 0x000
+#define MX25_PAD_PWM__GPIO_1_26			0x11c 0x314 0x000 0x15 0x000
+#define MX25_PAD_PWM__USBH2_OC			0x11c 0x314 0x580 0x16 0x001
+
+#define MX25_PAD_CSI_D2__CSI_D2			0x120 0x318 0x000 0x10 0x000
+#define MX25_PAD_CSI_D2__UART5_RXD_MUX		0x120 0x318 0x578 0x11 0x001
+#define MX25_PAD_CSI_D2__GPIO_1_27		0x120 0x318 0x000 0x15 0x000
+#define MX25_PAD_CSI_D2__CSPI3_MOSI		0x120 0x318 0x000 0x17 0x000
+
+#define MX25_PAD_CSI_D3__CSI_D3			0x124 0x31c 0x000 0x10 0x000
+#define MX25_PAD_CSI_D3__GPIO_1_28		0x124 0x31c 0x000 0x15 0x000
+#define MX25_PAD_CSI_D3__CSPI3_MISO		0x124 0x31c 0x4b4 0x17 0x001
+
+#define MX25_PAD_CSI_D4__CSI_D4			0x128 0x320 0x000 0x10 0x000
+#define MX25_PAD_CSI_D4__UART5_RTS		0x128 0x320 0x574 0x11 0x001
+#define MX25_PAD_CSI_D4__GPIO_1_29		0x128 0x320 0x000 0x15 0x000
+#define MX25_PAD_CSI_D4__CSPI3_SCLK		0x128 0x320 0x000 0x17 0x000
+
+#define MX25_PAD_CSI_D5__CSI_D5			0x12c 0x324 0x000 0x10 0x000
+#define MX25_PAD_CSI_D5__GPIO_1_30		0x12c 0x324 0x000 0x15 0x000
+#define MX25_PAD_CSI_D5__CSPI3_RDY		0x12c 0x324 0x000 0x17 0x000
+
+#define MX25_PAD_CSI_D6__CSI_D6			0x130 0x328 0x000 0x10 0x000
+#define MX25_PAD_CSI_D6__GPIO_1_31		0x130 0x328 0x000 0x15 0x000
+
+#define MX25_PAD_CSI_D7__CSI_D7			0x134 0x32c 0x000 0x10 0x000
+#define MX25_PAD_CSI_D7__GPIO_1_6		0x134 0x32c 0x000 0x15 0x000
+
+#define MX25_PAD_CSI_D8__CSI_D8			0x138 0x330 0x000 0x10 0x000
+#define MX25_PAD_CSI_D8__GPIO_1_7		0x138 0x330 0x000 0x15 0x000
+
+#define MX25_PAD_CSI_D9__CSI_D9			0x13c 0x334 0x000 0x10 0x000
+#define MX25_PAD_CSI_D9__GPIO_4_21		0x13c 0x334 0x000 0x15 0x000
+
+#define MX25_PAD_CSI_MCLK__CSI_MCLK		0x140 0x338 0x000 0x10 0x000
+#define MX25_PAD_CSI_MCLK__GPIO_1_8		0x140 0x338 0x000 0x15 0x000
+
+#define MX25_PAD_CSI_VSYNC__CSI_VSYNC		0x144 0x33c 0x000 0x10 0x000
+#define MX25_PAD_CSI_VSYNC__GPIO_1_9		0x144 0x33c 0x000 0x15 0x000
+
+#define MX25_PAD_CSI_HSYNC__CSI_HSYNC		0x148 0x340 0x000 0x10 0x000
+#define MX25_PAD_CSI_HSYNC__GPIO_1_10		0x148 0x340 0x000 0x15 0x000
+
+#define MX25_PAD_CSI_PIXCLK__CSI_PIXCLK		0x14c 0x344 0x000 0x10 0x000
+#define MX25_PAD_CSI_PIXCLK__GPIO_1_11		0x14c 0x344 0x000 0x15 0x000
+
+#define MX25_PAD_I2C1_CLK__I2C1_CLK		0x150 0x348 0x000 0x10 0x000
+#define MX25_PAD_I2C1_CLK__GPIO_1_12		0x150 0x348 0x000 0x15 0x000
+
+#define MX25_PAD_I2C1_DAT__I2C1_DAT		0x154 0x34c 0x000 0x10 0x000
+#define MX25_PAD_I2C1_DAT__GPIO_1_13		0x154 0x34c 0x000 0x15 0x000
+
+#define MX25_PAD_CSPI1_MOSI__CSPI1_MOSI		0x158 0x350 0x000 0x10 0x000
+#define MX25_PAD_CSPI1_MOSI__GPIO_1_14		0x158 0x350 0x000 0x15 0x000
+
+#define MX25_PAD_CSPI1_MISO__CSPI1_MISO		0x15c 0x354 0x000 0x10 0x000
+#define MX25_PAD_CSPI1_MISO__GPIO_1_15		0x15c 0x354 0x000 0x15 0x000
+
+#define MX25_PAD_CSPI1_SS0__CSPI1_SS0		0x160 0x358 0x000 0x10 0x000
+#define MX25_PAD_CSPI1_SS0__GPIO_1_16		0x160 0x358 0x000 0x15 0x000
+
+#define MX25_PAD_CSPI1_SS1__CSPI1_SS1		0x164 0x35c 0x000 0x10 0x000
+#define MX25_PAD_CSPI1_SS1__GPIO_1_17		0x164 0x35c 0x000 0x15 0x000
+
+#define MX25_PAD_CSPI1_SCLK__CSPI1_SCLK		0x168 0x360 0x000 0x10 0x000
+#define MX25_PAD_CSPI1_SCLK__GPIO_1_18		0x168 0x360 0x000 0x15 0x000
+
+#define MX25_PAD_CSPI1_RDY__CSPI1_RDY		0x16c 0x364 0x000 0x10 0x000
+#define MX25_PAD_CSPI1_RDY__GPIO_2_22		0x16c 0x364 0x000 0x15 0x000
+
+#define MX25_PAD_UART1_RXD__UART1_RXD		0x170 0x368 0x000 0x10 0x000
+#define MX25_PAD_UART1_RXD__GPIO_4_22		0x170 0x368 0x000 0x15 0x000
+
+#define MX25_PAD_UART1_TXD__UART1_TXD		0x174 0x36c 0x000 0x10 0x000
+#define MX25_PAD_UART1_TXD__GPIO_4_23		0x174 0x36c 0x000 0x15 0x000
+
+#define MX25_PAD_UART1_RTS__UART1_RTS		0x178 0x370 0x000 0x10 0x000
+#define MX25_PAD_UART1_RTS__CSI_D0		0x178 0x370 0x488 0x11 0x001
+#define MX25_PAD_UART1_RTS__GPIO_4_24		0x178 0x370 0x000 0x15 0x000
+
+#define MX25_PAD_UART1_CTS__UART1_CTS		0x17c 0x374 0x000 0x10 0x000
+#define MX25_PAD_UART1_CTS__CSI_D1		0x17c 0x374 0x48c 0x11 0x001
+#define MX25_PAD_UART1_CTS__GPIO_4_25		0x17c 0x374 0x000 0x15 0x000
+
+#define MX25_PAD_UART2_RXD__UART2_RXD		0x180 0x378 0x000 0x10 0x000
+#define MX25_PAD_UART2_RXD__GPIO_4_26		0x180 0x378 0x000 0x15 0x000
+
+#define MX25_PAD_UART2_TXD__UART2_TXD		0x184 0x37c 0x000 0x10 0x000
+#define MX25_PAD_UART2_TXD__GPIO_4_27		0x184 0x37c 0x000 0x15 0x000
+
+#define MX25_PAD_UART2_RTS__UART2_RTS		0x188 0x380 0x000 0x10 0x000
+#define MX25_PAD_UART2_RTS__FEC_COL		0x188 0x380 0x504 0x12 0x002
+#define MX25_PAD_UART2_RTS__GPIO_4_28		0x188 0x380 0x000 0x15 0x000
+
+#define MX25_PAD_UART2_CTS__FEC_RX_ER		0x18c 0x384 0x518 0x12 0x002
+#define MX25_PAD_UART2_CTS__UART2_CTS		0x18c 0x384 0x000 0x10 0x000
+#define MX25_PAD_UART2_CTS__GPIO_4_29		0x18c 0x384 0x000 0x15 0x000
+
+#define MX25_PAD_SD1_CMD__SD1_CMD		0x190 0x388 0x000 0x10 0x000
+#define MX25_PAD_SD1_CMD__FEC_RDATA2		0x190 0x388 0x50c 0x12 0x002
+#define MX25_PAD_SD1_CMD__GPIO_2_23		0x190 0x388 0x000 0x15 0x000
+
+#define MX25_PAD_SD1_CLK__SD1_CLK		0x194 0x38c 0x000 0x10 0x000
+#define MX25_PAD_SD1_CLK__FEC_RDATA3		0x194 0x38c 0x510 0x12 0x002
+#define MX25_PAD_SD1_CLK__GPIO_2_24		0x194 0x38c 0x000 0x15 0x000
+
+#define MX25_PAD_SD1_DATA0__SD1_DATA0		0x198 0x390 0x000 0x10 0x000
+#define MX25_PAD_SD1_DATA0__GPIO_2_25		0x198 0x390 0x000 0x15 0x000
+
+#define MX25_PAD_SD1_DATA1__SD1_DATA1		0x19c 0x394 0x000 0x10 0x000
+#define MX25_PAD_SD1_DATA1__AUD7_RXD		0x19c 0x394 0x478 0x13 0x000
+#define MX25_PAD_SD1_DATA1__GPIO_2_26		0x19c 0x394 0x000 0x15 0x000
+
+#define MX25_PAD_SD1_DATA2__SD1_DATA2		0x1a0 0x398 0x000 0x10 0x000
+#define MX25_PAD_SD1_DATA2__FEC_RX_CLK		0x1a0 0x398 0x514 0x15 0x002
+#define MX25_PAD_SD1_DATA2__GPIO_2_27		0x1a0 0x398 0x000 0x15 0x000
+
+#define MX25_PAD_SD1_DATA3__SD1_DATA3		0x1a4 0x39c 0x000 0x10 0x000
+#define MX25_PAD_SD1_DATA3__FEC_CRS		0x1a4 0x39c 0x508 0x10 0x002
+#define MX25_PAD_SD1_DATA3__GPIO_2_28		0x1a4 0x39c 0x000 0x15 0x000
+
+#define MX25_PAD_KPP_ROW0__KPP_ROW0		0x1a8 0x3a0 0x000 0x10 0x000
+#define MX25_PAD_KPP_ROW0__GPIO_2_29		0x1a8 0x3a0 0x000 0x15 0x000
+
+#define MX25_PAD_KPP_ROW1__KPP_ROW1		0x1ac 0x3a4 0x000 0x10 0x000
+#define MX25_PAD_KPP_ROW1__GPIO_2_30		0x1ac 0x3a4 0x000 0x15 0x000
+
+#define MX25_PAD_KPP_ROW2__KPP_ROW2		0x1b0 0x3a8 0x000 0x10 0x000
+#define MX25_PAD_KPP_ROW2__CSI_D0		0x1b0 0x3a8 0x488 0x13 0x002
+#define MX25_PAD_KPP_ROW2__GPIO_2_31		0x1b0 0x3a8 0x000 0x15 0x000
+
+#define MX25_PAD_KPP_ROW3__KPP_ROW3		0x1b4 0x3ac 0x000 0x10 0x000
+#define MX25_PAD_KPP_ROW3__CSI_LD1		0x1b4 0x3ac 0x48c 0x13 0x002
+#define MX25_PAD_KPP_ROW3__GPIO_3_0		0x1b4 0x3ac 0x000 0x15 0x000
+
+#define MX25_PAD_KPP_COL0__KPP_COL0		0x1b8 0x3b0 0x000 0x10 0x000
+#define MX25_PAD_KPP_COL0__UART4_RXD_MUX	0x1b8 0x3b0 0x570 0x11 0x001
+#define MX25_PAD_KPP_COL0__AUD5_TXD		0x1b8 0x3b0 0x000 0x12 0x000
+#define MX25_PAD_KPP_COL0__GPIO_3_1		0x1b8 0x3b0 0x000 0x15 0x000
+
+#define MX25_PAD_KPP_COL1__KPP_COL1		0x1bc 0x3b4 0x000 0x10 0x000
+#define MX25_PAD_KPP_COL1__UART4_TXD_MUX	0x1bc 0x3b4 0x000 0x11 0x000
+#define MX25_PAD_KPP_COL1__AUD5_RXD		0x1bc 0x3b4 0x000 0x12 0x000
+#define MX25_PAD_KPP_COL1__GPIO_3_2		0x1bc 0x3b4 0x000 0x15 0x000
+
+#define MX25_PAD_KPP_COL2__KPP_COL2		0x1c0 0x3b8 0x000 0x10 0x000
+#define MX25_PAD_KPP_COL2__UART4_RTS		0x1c0 0x3b8 0x000 0x11 0x000
+#define MX25_PAD_KPP_COL2__AUD5_TXC		0x1c0 0x3b8 0x000 0x12 0x000
+#define MX25_PAD_KPP_COL2__GPIO_3_3		0x1c0 0x3b8 0x000 0x15 0x000
+
+#define MX25_PAD_KPP_COL3__KPP_COL3		0x1c4 0x3bc 0x000 0x10 0x000
+#define MX25_PAD_KPP_COL3__UART4_CTS		0x1c4 0x3bc 0x000 0x11 0x000
+#define MX25_PAD_KPP_COL3__AUD5_TXFS		0x1c4 0x3bc 0x000 0x12 0x000
+#define MX25_PAD_KPP_COL3__GPIO_3_4		0x1c4 0x3bc 0x000 0x15 0x000
+
+#define MX25_PAD_FEC_MDC__FEC_MDC		0x1c8 0x3c0 0x000 0x10 0x000
+#define MX25_PAD_FEC_MDC__AUD4_TXD		0x1c8 0x3c0 0x464 0x12 0x001
+#define MX25_PAD_FEC_MDC__GPIO_3_5		0x1c8 0x3c0 0x000 0x15 0x000
+
+#define MX25_PAD_FEC_MDIO__FEC_MDIO		0x1cc 0x3c4 0x000 0x10 0x000
+#define MX25_PAD_FEC_MDIO__AUD4_RXD		0x1cc 0x3c4 0x460 0x12 0x001
+#define MX25_PAD_FEC_MDIO__GPIO_3_6		0x1cc 0x3c4 0x000 0x15 0x000
+
+#define MX25_PAD_FEC_TDATA0__FEC_TDATA0		0x1d0 0x3c8 0x000 0x10 0x000
+#define MX25_PAD_FEC_TDATA0__GPIO_3_7		0x1d0 0x3c8 0x000 0x15 0x000
+
+#define MX25_PAD_FEC_TDATA1__FEC_TDATA1		0x1d4 0x3cc 0x000 0x10 0x000
+#define MX25_PAD_FEC_TDATA1__AUD4_TXFS		0x1d4 0x3cc 0x474 0x12 0x001
+#define MX25_PAD_FEC_TDATA1__GPIO_3_8		0x1d4 0x3cc 0x000 0x15 0x000
+
+#define MX25_PAD_FEC_TX_EN__FEC_TX_EN		0x1d8 0x3d0 0x000 0x10 0x000
+#define MX25_PAD_FEC_TX_EN__GPIO_3_9		0x1d8 0x3d0 0x000 0x15 0x000
+
+#define MX25_PAD_FEC_RDATA0__FEC_RDATA0		0x1dc 0x3d4 0x000 0x10 0x000
+#define MX25_PAD_FEC_RDATA0__GPIO_3_10		0x1dc 0x3d4 0x000 0x15 0x000
+
+#define MX25_PAD_FEC_RDATA1__FEC_RDATA1		0x1e0 0x3d8 0x000 0x10 0x000
+#define MX25_PAD_FEC_RDATA1__GPIO_3_11		0x1e0 0x3d8 0x000 0x15 0x000
+
+#define MX25_PAD_FEC_RX_DV__FEC_RX_DV		0x1e4 0x3dc 0x000 0x10 0x000
+#define MX25_PAD_FEC_RX_DV__CAN2_RX		0x1e4 0x3dc 0x484 0x14 0x000
+#define MX25_PAD_FEC_RX_DV__GPIO_3_12		0x1e4 0x3dc 0x000 0x15 0x000
+
+#define MX25_PAD_FEC_TX_CLK__FEC_TX_CLK		0x1e8 0x3e0 0x000 0x10 0x000
+#define MX25_PAD_FEC_TX_CLK__GPIO_3_13		0x1e8 0x3e0 0x000 0x15 0x000
+
+#define MX25_PAD_RTCK__RTCK			0x1ec 0x3e4 0x000 0x10 0x000
+#define MX25_PAD_RTCK__OWIRE			0x1ec 0x3e4 0x000 0x11 0x000
+#define MX25_PAD_RTCK__GPIO_3_14		0x1ec 0x3e4 0x000 0x15 0x000
+
+#define MX25_PAD_DE_B__DE_B			0x1f0 0x3ec 0x000 0x10 0x000
+#define MX25_PAD_DE_B__GPIO_2_20		0x1f0 0x3ec 0x000 0x15 0x000
+
+#define MX25_PAD_TDO__TDO			0x000 0x3e8 0x000 0x00 0x000
+
+#define MX25_PAD_GPIO_A__GPIO_A			0x1f4 0x3f0 0x000 0x10 0x000
+#define MX25_PAD_GPIO_A__CAN1_TX		0x1f4 0x3f0 0x000 0x16 0x000
+#define MX25_PAD_GPIO_A__USBOTG_PWR		0x1f4 0x3f0 0x000 0x12 0x000
+
+#define MX25_PAD_GPIO_B__GPIO_B			0x1f8 0x3f4 0x000 0x10 0x000
+#define MX25_PAD_GPIO_B__CAN1_RX		0x1f8 0x3f4 0x480 0x16 0x001
+#define MX25_PAD_GPIO_B__USBOTG_OC		0x1f8 0x3f4 0x57c 0x12 0x001
+
+#define MX25_PAD_GPIO_C__GPIO_C			0x1fc 0x3f8 0x000 0x10 0x000
+#define MX25_PAD_GPIO_C__CAN2_TX		0x1fc 0x3f8 0x000 0x16 0x000
+
+#define MX25_PAD_GPIO_D__GPIO_D			0x200 0x3fc 0x000 0x10 0x000
+#define MX25_PAD_GPIO_E__LD16			0x204 0x400 0x000 0x02 0x000
+#define MX25_PAD_GPIO_D__CAN2_RX		0x200 0x3fc 0x484 0x16 0x001
+
+#define MX25_PAD_GPIO_E__GPIO_E			0x204 0x400 0x000 0x10 0x000
+#define MX25_PAD_GPIO_F__LD17			0x208 0x404 0x000 0x02 0x000
+#define MX25_PAD_GPIO_E__AUD7_TXD		0x204 0x400 0x000 0x14 0x000
+
+#define MX25_PAD_GPIO_F__GPIO_F			0x208 0x404 0x000 0x10 0x000
+#define MX25_PAD_GPIO_F__AUD7_TXC		0x208 0x404 0x000 0x14 0x000
+
+#define MX25_PAD_EXT_ARMCLK__EXT_ARMCLK		0x20c 0x000 0x000 0x10 0x000
+#define MX25_PAD_EXT_ARMCLK__GPIO_3_15		0x20c 0x000 0x000 0x15 0x000
+
+#define MX25_PAD_UPLL_BYPCLK__UPLL_BYPCLK	0x210 0x000 0x000 0x10 0x000
+#define MX25_PAD_UPLL_BYPCLK__GPIO_3_16		0x210 0x000 0x000 0x15 0x000
+
+#define MX25_PAD_VSTBY_REQ__VSTBY_REQ		0x214 0x408 0x000 0x10 0x000
+#define MX25_PAD_VSTBY_REQ__AUD7_TXFS		0x214 0x408 0x000 0x14 0x000
+#define MX25_PAD_VSTBY_REQ__GPIO_3_17		0x214 0x408 0x000 0x15 0x000
+#define MX25_PAD_VSTBY_ACK__VSTBY_ACK		0x218 0x40c 0x000 0x10 0x000
+#define MX25_PAD_VSTBY_ACK__GPIO_3_18		0x218 0x40c 0x000 0x15 0x000
+
+#define MX25_PAD_POWER_FAIL__POWER_FAIL		0x21c 0x410 0x000 0x10 0x000
+#define MX25_PAD_POWER_FAIL__AUD7_RXD		0x21c 0x410 0x478 0x14 0x001
+#define MX25_PAD_POWER_FAIL__GPIO_3_19		0x21c 0x410 0x000 0x15 0x000
+
+#define MX25_PAD_CLKO__CLKO			0x220 0x414 0x000 0x10 0x000
+#define MX25_PAD_CLKO__GPIO_2_21		0x220 0x414 0x000 0x15 0x000
+
+#define MX25_PAD_BOOT_MODE0__BOOT_MODE0		0x224 0x000 0x000 0x00 0x000
+#define MX25_PAD_BOOT_MODE0__GPIO_4_30		0x224 0x000 0x000 0x05 0x000
+#define MX25_PAD_BOOT_MODE1__BOOT_MODE1		0x228 0x000 0x000 0x00 0x000
+#define MX25_PAD_BOOT_MODE1__GPIO_4_31		0x228 0x000 0x000 0x05 0x000
+
+#endif /* __DTS_IMX25_PINFUNC_H */

arch/arm/boot/dts/imx25.dtsi

@@ -10,6 +10,7 @@
  */
 
 #include "skeleton.dtsi"
+#include "imx25-pinfunc.h"
 
 / {
 	aliases {
@@ -173,12 +174,12 @@
 				status = "disabled";
 			};
 
-			iomuxc@43fac000{
+			iomuxc: iomuxc@43fac000 {
 				compatible = "fsl,imx25-iomuxc";
 				reg = <0x43fac000 0x4000>;
 			};
 
-			audmux@43fb0000 {
+			audmux: audmux@43fb0000 {
 				compatible = "fsl,imx25-audmux", "fsl,imx31-audmux";
 				reg = <0x43fb0000 0x4000>;
 				status = "disabled";
@@ -236,6 +237,11 @@
 				compatible = "fsl,imx25-ssi", "fsl,imx21-ssi";
 				reg = <0x50014000 0x4000>;
 				interrupts = <11>;
+				clocks = <&clks 118>;
+				clock-names = "ipg";
+				dmas = <&sdma 24 1 0>,
+				       <&sdma 25 1 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -266,6 +272,11 @@
 				compatible = "fsl,imx25-ssi", "fsl,imx21-ssi";
 				reg = <0x50034000 0x4000>;
 				interrupts = <12>;
+				clocks = <&clks 117>;
+				clock-names = "ipg";
+				dmas = <&sdma 28 1 0>,
+				       <&sdma 29 1 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -436,13 +447,14 @@
 				#interrupt-cells = <2>;
 			};
 
-			sdma@53fd4000 {
+			sdma: sdma@53fd4000 {
 				compatible = "fsl,imx25-sdma", "fsl,imx35-sdma";
 				reg = <0x53fd4000 0x4000>;
 				clocks = <&clks 112>, <&clks 68>;
 				clock-names = "ipg", "ahb";
 				#dma-cells = <3>;
 				interrupts = <34>;
+				fsl,sdma-ram-script-name = "imx/sdma/sdma-imx25.bin";
 			};
 
 			wdog@53fdc000 {

arch/arm/boot/dts/imx27-apf27.dts

@@ -34,11 +34,49 @@
 	};
 };
 
+&iomuxc {
+	imx27-apf27 {
+		pinctrl_fec1: fec1grp {
+			fsl,pins = <
+				MX27_PAD_SD3_CMD__FEC_TXD0 0x0
+				MX27_PAD_SD3_CLK__FEC_TXD1 0x0
+				MX27_PAD_ATA_DATA0__FEC_TXD2 0x0
+				MX27_PAD_ATA_DATA1__FEC_TXD3 0x0
+				MX27_PAD_ATA_DATA2__FEC_RX_ER 0x0
+				MX27_PAD_ATA_DATA3__FEC_RXD1 0x0
+				MX27_PAD_ATA_DATA4__FEC_RXD2 0x0
+				MX27_PAD_ATA_DATA5__FEC_RXD3 0x0
+				MX27_PAD_ATA_DATA6__FEC_MDIO 0x0
+				MX27_PAD_ATA_DATA7__FEC_MDC 0x0
+				MX27_PAD_ATA_DATA8__FEC_CRS 0x0
+				MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x0
+				MX27_PAD_ATA_DATA10__FEC_RXD0 0x0
+				MX27_PAD_ATA_DATA11__FEC_RX_DV 0x0
+				MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x0
+				MX27_PAD_ATA_DATA13__FEC_COL 0x0
+				MX27_PAD_ATA_DATA14__FEC_TX_ER 0x0
+				MX27_PAD_ATA_DATA15__FEC_TX_EN 0x0
+			>;
+		};
+
+		pinctrl_uart1: uart1grp {
+			fsl,pins = <
+				MX27_PAD_UART1_TXD__UART1_TXD 0x0
+				MX27_PAD_UART1_RXD__UART1_RXD 0x0
+			>;
+		};
+	};
+};
+
 &uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
 	status = "okay";
 };
 
 &fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
 	status = "okay";
 };
 

arch/arm/boot/dts/imx27-apf27dev.dts

@@ -22,10 +22,10 @@
 		bits-per-pixel = <16>;  /* non-standard but required */
 		fsl,pcr = <0xfae80083>;	/* non-standard but required */
 		display-timings {
-			timing0: 640x480 {
+			timing0: 800x480 {
 				clock-frequency = <33000033>;
 				hactive = <800>;
-				vactive = <640>;
+				vactive = <480>;
 				hback-porch = <96>;
 				hfront-porch = <96>;
 				vback-porch = <20>;
@@ -38,20 +38,24 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
 
 		user-key {
 			label = "user";
-			gpios = <&gpio6 13 0>;
+			gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
 			linux,code = <276>; /* BTN_EXTRA */
 		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
 
 		user {
 			label = "Heartbeat";
-			gpios = <&gpio6 14 0>;
+			gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 	};
@@ -59,25 +63,34 @@
 
 &cspi1 {
 	fsl,spi-num-chipselects = <1>;
-	cs-gpios = <&gpio4 28 1>;
+	cs-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cspi1 &pinctrl_cspi1_cs>;
 	status = "okay";
 };
 
 &cspi2 {
 	fsl,spi-num-chipselects = <3>;
-	cs-gpios = <&gpio4 21 1>, <&gpio4 27 1>,
-			<&gpio2 17 1>;
+	cs-gpios = <&gpio4 21 GPIO_ACTIVE_LOW>,
+		   <&gpio4 27 GPIO_ACTIVE_LOW>,
+		   <&gpio2 17 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cspi2 &pinctrl_cspi2_cs>;
 	status = "okay";
 };
 
 &fb {
 	display = <&display>;
 	fsl,dmacr = <0x00020010>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_imxfb1>;
 	status = "okay";
 };
 
 &i2c1 {
 	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
 	rtc@68 {
@@ -87,5 +100,127 @@
 };
 
 &i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 };
+
+&iomuxc {
+	imx27-apf27dev {
+		pinctrl_cspi1: cspi1grp {
+			fsl,pins = <
+				MX27_PAD_CSPI1_MISO__CSPI1_MISO 0x0
+				MX27_PAD_CSPI1_MOSI__CSPI1_MOSI 0x0
+				MX27_PAD_CSPI1_SCLK__CSPI1_SCLK 0x0
+			>;
+		};
+
+		pinctrl_cspi1_cs: cspi1csgrp {
+			fsl,pins = <MX27_PAD_CSPI1_SS0__GPIO4_28 0x0>;
+		};
+
+		pinctrl_cspi2: cspi2grp {
+			fsl,pins = <
+				MX27_PAD_CSPI2_MISO__CSPI2_MISO 0x0
+				MX27_PAD_CSPI2_MOSI__CSPI2_MOSI 0x0
+				MX27_PAD_CSPI2_SCLK__CSPI2_SCLK 0x0
+			>;
+		};
+
+		pinctrl_cspi2_cs: cspi2csgrp {
+			fsl,pins = <
+				MX27_PAD_CSI_D5__GPIO2_17 0x0
+				MX27_PAD_CSPI2_SS0__GPIO4_21 0x0
+				MX27_PAD_CSPI1_SS1__GPIO4_27 0x0
+			>;
+		};
+
+		pinctrl_gpio_leds: gpioledsgrp {
+			fsl,pins = <MX27_PAD_PC_VS1__GPIO6_14 0x0>;
+		};
+
+		pinctrl_gpio_keys: gpiokeysgrp {
+			fsl,pins = <MX27_PAD_PC_VS2__GPIO6_13 0x0>;
+		};
+
+		pinctrl_imxfb1: imxfbgrp {
+			fsl,pins = <
+				MX27_PAD_CLS__CLS 0x0
+				MX27_PAD_CONTRAST__CONTRAST 0x0
+				MX27_PAD_LD0__LD0 0x0
+				MX27_PAD_LD1__LD1 0x0
+				MX27_PAD_LD2__LD2 0x0
+				MX27_PAD_LD3__LD3 0x0
+				MX27_PAD_LD4__LD4 0x0
+				MX27_PAD_LD5__LD5 0x0
+				MX27_PAD_LD6__LD6 0x0
+				MX27_PAD_LD7__LD7 0x0
+				MX27_PAD_LD8__LD8 0x0
+				MX27_PAD_LD9__LD9 0x0
+				MX27_PAD_LD10__LD10 0x0
+				MX27_PAD_LD11__LD11 0x0
+				MX27_PAD_LD12__LD12 0x0
+				MX27_PAD_LD13__LD13 0x0
+				MX27_PAD_LD14__LD14 0x0
+				MX27_PAD_LD15__LD15 0x0
+				MX27_PAD_LD16__LD16 0x0
+				MX27_PAD_LD17__LD17 0x0
+				MX27_PAD_LSCLK__LSCLK 0x0
+				MX27_PAD_OE_ACD__OE_ACD 0x0
+				MX27_PAD_PS__PS 0x0
+				MX27_PAD_REV__REV 0x0
+				MX27_PAD_SPL_SPR__SPL_SPR 0x0
+				MX27_PAD_HSYNC__HSYNC 0x0
+				MX27_PAD_VSYNC__VSYNC 0x0
+			>;
+		};
+
+		pinctrl_i2c1: i2c1grp {
+			fsl,pins = <
+				MX27_PAD_I2C_DATA__I2C_DATA 0x0
+				MX27_PAD_I2C_CLK__I2C_CLK 0x0
+			>;
+		};
+
+		pinctrl_i2c2: i2c2grp {
+			fsl,pins = <
+				MX27_PAD_I2C2_SDA__I2C2_SDA 0x0
+				MX27_PAD_I2C2_SCL__I2C2_SCL 0x0
+			>;
+		};
+
+		pinctrl_pwm: pwmgrp {
+			fsl,pins = <
+				MX27_PAD_PWMO__PWMO 0x0
+			>;
+		};
+
+		pinctrl_sdhc2: sdhc2grp {
+			fsl,pins = <
+				MX27_PAD_SD2_CLK__SD2_CLK 0x0
+				MX27_PAD_SD2_CMD__SD2_CMD 0x0
+				MX27_PAD_SD2_D0__SD2_D0 0x0
+				MX27_PAD_SD2_D1__SD2_D1 0x0
+				MX27_PAD_SD2_D2__SD2_D2 0x0
+				MX27_PAD_SD2_D3__SD2_D3 0x0
+			>;
+		};
+
+		pinctrl_sdhc2_cd: sdhc2cdgrp {
+			fsl,pins = <MX27_PAD_TOUT__GPIO3_14 0x0>;
+		};
+	};
+};
+
+&sdhci2 {
+	bus-width = <4>;
+	cd-gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhc2 &pinctrl_sdhc2_cd>;
+	status = "okay";
+};
+
+&pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm>;
+};

arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts

@@ -9,7 +9,7 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
-#include "imx27-phytec-phycard-s-som.dts"
+#include "imx27-phytec-phycard-s-som.dtsi"
 
 / {
 	model = "Phytec pca100 rapid development kit";
@@ -37,9 +37,12 @@
 
 	regulators {
 		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		reg_3v3: 3v3 {
+		reg_3v3: regulator@0 {
 			compatible = "regulator-fixed";
+			reg = <0>;
 			regulator-name = "3V3";
 			regulator-min-microvolt = <3300000>;
 			regulator-max-microvolt = <3300000>;
@@ -54,6 +57,8 @@
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
 	rtc@51 {
@@ -68,26 +73,92 @@
 	};
 };
 
+&iomuxc {
+	imx27-phycard-s-rdk {
+		pinctrl_i2c1: i2c1grp {
+			fsl,pins = <
+				MX27_PAD_I2C2_SDA__I2C2_SDA 0x0
+				MX27_PAD_I2C2_SCL__I2C2_SCL 0x0
+			>;
+		};
+
+		pinctrl_owire1: owire1grp {
+			fsl,pins = <
+				MX27_PAD_RTCK__OWIRE 0x0
+			>;
+		};
+
+		pinctrl_sdhc2: sdhc2grp {
+			fsl,pins = <
+				MX27_PAD_SD2_CLK__SD2_CLK 0x0
+				MX27_PAD_SD2_CMD__SD2_CMD 0x0
+				MX27_PAD_SD2_D0__SD2_D0 0x0
+				MX27_PAD_SD2_D1__SD2_D1 0x0
+				MX27_PAD_SD2_D2__SD2_D2 0x0
+				MX27_PAD_SD2_D3__SD2_D3 0x0
+				MX27_PAD_SSI3_RXDAT__GPIO3_29 0x0 /* CD */
+			>;
+		};
+
+		pinctrl_uart1: uart1grp {
+			fsl,pins = <
+				MX27_PAD_UART1_TXD__UART1_TXD 0x0
+				MX27_PAD_UART1_RXD__UART1_RXD 0x0
+				MX27_PAD_UART1_CTS__UART1_CTS 0x0
+				MX27_PAD_UART1_RTS__UART1_RTS 0x0
+			>;
+		};
+
+		pinctrl_uart2: uart2grp {
+			fsl,pins = <
+				MX27_PAD_UART2_TXD__UART2_TXD 0x0
+				MX27_PAD_UART2_RXD__UART2_RXD 0x0
+				MX27_PAD_UART2_CTS__UART2_CTS 0x0
+				MX27_PAD_UART2_RTS__UART2_RTS 0x0
+			>;
+		};
+
+		pinctrl_uart3: uart3grp {
+			fsl,pins = <
+				MX27_PAD_UART3_TXD__UART3_TXD 0x0
+				MX27_PAD_UART3_RXD__UART3_RXD 0x0
+				MX27_PAD_UART3_CTS__UART3_CTS 0x0
+				MX27_PAD_UART3_RTS__UART3_RTS 0x0
+			>;
+		};
+	};
+};
+
 &owire {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_owire1>;
 	status = "okay";
 };
 
 &sdhci2 {
-	cd-gpios = <&gpio3 29 0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhc2>;
+	cd-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &uart1 {
 	fsl,uart-has-rtscts;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
 	status = "okay";
 };
 
 &uart2 {
 	fsl,uart-has-rtscts;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
 	status = "okay";
 };
 
 &uart3 {
 	fsl,uart-has-rtscts;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
 	status = "okay";
 };

arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts

@@ -1,44 +0,0 @@
-/*
- * Copyright 2012 Sascha Hauer, Uwe Kleine-König, Steffen Trumtrar
- * and Markus Pargmann, Pengutronix
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 or later at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
- */
-
-/dts-v1/;
-#include "imx27.dtsi"
-
-/ {
-	model = "Phytec pca100";
-	compatible = "phytec,imx27-pca100", "fsl,imx27";
-
-	memory {
-		reg = <0xa0000000 0x08000000>; /* 128MB */
-	};
-};
-
-&cspi1 {
-	fsl,spi-num-chipselects = <2>;
-	cs-gpios = <&gpio4 28 0>,
-		<&gpio4 27 0>;
-	status = "okay";
-};
-
-&fec {
-	status = "okay";
-};
-
-&i2c2 {
-	status = "okay";
-
-	at24@52 {
-		compatible = "at,24c32";
-		pagesize = <32>;
-		reg = <0x52>;
-	};
-};

arch/arm/boot/dts/imx27-phytec-phycard-s-som.dtsi

@@ -0,0 +1,103 @@
+/*
+ * Copyright 2012 Sascha Hauer, Uwe Kleine-König, Steffen Trumtrar
+ * and Markus Pargmann, Pengutronix
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "imx27.dtsi"
+
+/ {
+	model = "Phytec pca100";
+	compatible = "phytec,imx27-pca100", "fsl,imx27";
+
+	memory {
+		reg = <0xa0000000 0x08000000>; /* 128MB */
+	};
+};
+
+&cspi1 {
+	fsl,spi-num-chipselects = <2>;
+	cs-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>,
+		   <&gpio4 27 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	at24@52 {
+		compatible = "at,24c32";
+		pagesize = <32>;
+		reg = <0x52>;
+	};
+};
+
+&iomuxc {
+	imx27-phycard-s-som {
+		pinctrl_fec1: fec1grp {
+			fsl,pins = <
+				MX27_PAD_SD3_CMD__FEC_TXD0 0x0
+				MX27_PAD_SD3_CLK__FEC_TXD1 0x0
+				MX27_PAD_ATA_DATA0__FEC_TXD2 0x0
+				MX27_PAD_ATA_DATA1__FEC_TXD3 0x0
+				MX27_PAD_ATA_DATA2__FEC_RX_ER 0x0
+				MX27_PAD_ATA_DATA3__FEC_RXD1 0x0
+				MX27_PAD_ATA_DATA4__FEC_RXD2 0x0
+				MX27_PAD_ATA_DATA5__FEC_RXD3 0x0
+				MX27_PAD_ATA_DATA6__FEC_MDIO 0x0
+				MX27_PAD_ATA_DATA7__FEC_MDC 0x0
+				MX27_PAD_ATA_DATA8__FEC_CRS 0x0
+				MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x0
+				MX27_PAD_ATA_DATA10__FEC_RXD0 0x0
+				MX27_PAD_ATA_DATA11__FEC_RX_DV 0x0
+				MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x0
+				MX27_PAD_ATA_DATA13__FEC_COL 0x0
+				MX27_PAD_ATA_DATA14__FEC_TX_ER 0x0
+				MX27_PAD_ATA_DATA15__FEC_TX_EN 0x0
+			>;
+		};
+
+		pinctrl_i2c2: i2c2grp {
+			fsl,pins = <
+				MX27_PAD_I2C2_SDA__I2C2_SDA 0x0
+				MX27_PAD_I2C2_SCL__I2C2_SCL 0x0
+			>;
+		};
+
+		pinctrl_nfc: nfcgrp {
+			fsl,pins = <
+				MX27_PAD_NFRB__NFRB 0x0
+				MX27_PAD_NFCLE__NFCLE 0x0
+				MX27_PAD_NFWP_B__NFWP_B 0x0
+				MX27_PAD_NFCE_B__NFCE_B 0x0
+				MX27_PAD_NFALE__NFALE 0x0
+				MX27_PAD_NFRE_B__NFRE_B 0x0
+				MX27_PAD_NFWE_B__NFWE_B 0x0
+			>;
+		};
+	};
+};
+
+&nfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nfc>;
+	nand-bus-width = <8>;
+	nand-ecc-mode = "hw";
+	nand-on-flash-bbt;
+	status = "okay";
+};

arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts

@@ -7,7 +7,7 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
-#include "imx27-phytec-phycore-som.dts"
+#include "imx27-phytec-phycore-som.dtsi"
 
 / {
 	model = "Phytec pcm970";
@@ -16,32 +16,200 @@
 
 &cspi1 {
 	fsl,spi-num-chipselects = <2>;
-	cs-gpios = <&gpio4 28 0>, <&gpio4 27 0>;
+	cs-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>,
+		   <&gpio4 27 GPIO_ACTIVE_LOW>;
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	camgpio: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&iomuxc {
+	imx27_phycore_rdk {
+		pinctrl_i2c1: i2c1grp {
+			/* Add pullup to DATA line */
+			fsl,pins = <
+				MX27_PAD_I2C_DATA__I2C_DATA	0x1
+				MX27_PAD_I2C_CLK__I2C_CLK	0x0
+			>;
+		};
+
+		pinctrl_owire1: owire1grp {
+			fsl,pins = <
+				MX27_PAD_RTCK__OWIRE 0x0
+			>;
+		};
+
+		pinctrl_sdhc2: sdhc2grp {
+			fsl,pins = <
+				MX27_PAD_SD2_CLK__SD2_CLK 0x0
+				MX27_PAD_SD2_CMD__SD2_CMD 0x0
+				MX27_PAD_SD2_D0__SD2_D0 0x0
+				MX27_PAD_SD2_D1__SD2_D1 0x0
+				MX27_PAD_SD2_D2__SD2_D2 0x0
+				MX27_PAD_SD2_D3__SD2_D3 0x0
+				MX27_PAD_SSI3_FS__GPIO3_28	0x0 /* WP */
+				MX27_PAD_SSI3_RXDAT__GPIO3_29	0x0 /* CD */
+			>;
+		};
+
+		pinctrl_uart1: uart1grp {
+			fsl,pins = <
+				MX27_PAD_UART1_TXD__UART1_TXD 0x0
+				MX27_PAD_UART1_RXD__UART1_RXD 0x0
+				MX27_PAD_UART1_CTS__UART1_CTS 0x0
+				MX27_PAD_UART1_RTS__UART1_RTS 0x0
+			>;
+		};
+
+		pinctrl_uart2: uart2grp {
+			fsl,pins = <
+				MX27_PAD_UART2_TXD__UART2_TXD 0x0
+				MX27_PAD_UART2_RXD__UART2_RXD 0x0
+				MX27_PAD_UART2_CTS__UART2_CTS 0x0
+				MX27_PAD_UART2_RTS__UART2_RTS 0x0
+			>;
+		};
+
+		pinctrl_usbh2: usbh2grp {
+			fsl,pins = <
+				MX27_PAD_USBH2_CLK__USBH2_CLK 0x0
+				MX27_PAD_USBH2_DIR__USBH2_DIR 0x0
+				MX27_PAD_USBH2_NXT__USBH2_NXT 0x0
+				MX27_PAD_USBH2_STP__USBH2_STP 0x0
+				MX27_PAD_CSPI2_SCLK__USBH2_DATA0 0x0
+				MX27_PAD_CSPI2_MOSI__USBH2_DATA1 0x0
+				MX27_PAD_CSPI2_MISO__USBH2_DATA2 0x0
+				MX27_PAD_CSPI2_SS1__USBH2_DATA3 0x0
+				MX27_PAD_CSPI2_SS2__USBH2_DATA4 0x0
+				MX27_PAD_CSPI1_SS2__USBH2_DATA5 0x0
+				MX27_PAD_CSPI2_SS0__USBH2_DATA6 0x0
+				MX27_PAD_USBH2_DATA7__USBH2_DATA7 0x0
+			>;
+		};
+
+		pinctrl_weim: weimgrp {
+			fsl,pins = <
+				MX27_PAD_CS4_B__CS4_B		0x0 /* CS4 */
+				MX27_PAD_SD1_D1__GPIO5_19	0x0 /* CAN IRQ */
+			>;
+		};
+	};
+};
+
+&owire {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_owire1>;
+	status = "okay";
+};
+
+&pmicleds {
+	ledr1: led@3 {
+		reg = <3>;
+		label = "system:red1:user";
+	};
+
+	ledg1: led@4 {
+		reg = <4>;
+		label = "system:green1:user";
+	};
+
+	ledb1: led@5 {
+		reg = <5>;
+		label = "system:blue1:user";
+	};
+
+	ledr2: led@6 {
+		reg = <6>;
+		label = "system:red2:user";
+	};
+
+	ledg2: led@7 {
+		reg = <7>;
+		label = "system:green2:user";
+	};
+
+	ledb2: led@8 {
+		reg = <8>;
+		label = "system:blue2:user";
+	};
+
+	ledr3: led@9 {
+		reg = <9>;
+		label = "system:red3:nand";
+		linux,default-trigger = "nand-disk";
+	};
+
+	ledg3: led@10 {
+		reg = <10>;
+		label = "system:green3:live";
+		linux,default-trigger = "heartbeat";
+	};
+
+	ledb3: led@11 {
+		reg = <11>;
+		label = "system:blue3:cpu";
+		linux,default-trigger = "cpu0";
+	};
 };
 
 &sdhci2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sdhc2>;
 	bus-width = <4>;
-	cd-gpios = <&gpio3 29 0>;
-	wp-gpios = <&gpio3 28 0>;
+	cd-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
+	wp-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>;
 	vmmc-supply = <&vmmc1_reg>;
 	status = "okay";
 };
 
 &uart1 {
 	fsl,uart-has-rtscts;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
 };
 
 &uart2 {
 	fsl,uart-has-rtscts;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usbh2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbh2>;
+	dr_mode = "host";
+	phy_type = "ulpi";
+	vbus-supply = <&reg_5v0>;
+	disable-over-current;
 	status = "okay";
 };
 
+&usbphy2 {
+	vcc-supply = <&reg_5v0>;
+};
+
 &weim {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_weim>;
+
 	can@d4000000 {
 		compatible = "nxp,sja1000";
 		reg = <4 0x00000000 0x00000100>;
 		interrupt-parent = <&gpio5>;
-		interrupts = <19 0x2>;
+		interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
 		nxp,external-clock-frequency = <16000000>;
 		nxp,tx-output-config = <0x16>;
 		nxp,no-comparator-bypass;

arch/arm/boot/dts/imx27-phytec-phycore-som.dts → arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi

@@ -19,6 +19,28 @@
 	memory {
 		reg = <0xa0000000 0x08000000>;
 	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg_3v3: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "3V3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		reg_5v0: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "5V0";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+		};
+	};
 };
 
 &audmux {
@@ -37,21 +59,30 @@
 };
 
 &cspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cspi1>;
 	fsl,spi-num-chipselects = <1>;
-	cs-gpios = <&gpio4 28 0>;
+	cs-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 
 	pmic: mc13783@0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "fsl,mc13783";
-		spi-max-frequency = <20000000>;
 		reg = <0>;
+		spi-cs-high;
+		spi-max-frequency = <20000000>;
 		interrupt-parent = <&gpio2>;
-		interrupts = <23 0x4>;
+		interrupts = <23 IRQ_TYPE_LEVEL_HIGH>;
 		fsl,mc13xxx-uses-adc;
 		fsl,mc13xxx-uses-rtc;
 
+		pmicleds: leds {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			led-control = <0x001 0x000 0x000 0x000 0x000 0x000>;
+		};
+
 		regulators {
 			/* SW1A and SW1B joined operation */
 			sw1_reg: sw1a {
@@ -134,12 +165,18 @@
 };
 
 &fec {
-	phy-reset-gpios = <&gpio3 30 0>;
+	phy-mode = "mii";
+	phy-reset-gpios = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+	phy-supply = <&reg_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
 	status = "okay";
 };
 
 &i2c2 {
 	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
 	at24@52 {
@@ -159,16 +196,102 @@
 	};
 };
 
+&iomuxc {
+	imx27_phycore_som {
+		pinctrl_cspi1: cspi1grp {
+			fsl,pins = <
+				MX27_PAD_CSPI1_MISO__CSPI1_MISO 0x0
+				MX27_PAD_CSPI1_MOSI__CSPI1_MOSI 0x0
+				MX27_PAD_CSPI1_SCLK__CSPI1_SCLK 0x0
+				MX27_PAD_CSPI1_SS0__GPIO4_28	0x0 /* SPI1 CS0 */
+				MX27_PAD_USB_PWR__GPIO2_23	0x0 /* PMIC IRQ */
+			>;
+		};
+
+		pinctrl_fec1: fec1grp {
+			fsl,pins = <
+				MX27_PAD_SD3_CMD__FEC_TXD0 0x0
+				MX27_PAD_SD3_CLK__FEC_TXD1 0x0
+				MX27_PAD_ATA_DATA0__FEC_TXD2 0x0
+				MX27_PAD_ATA_DATA1__FEC_TXD3 0x0
+				MX27_PAD_ATA_DATA2__FEC_RX_ER 0x0
+				MX27_PAD_ATA_DATA3__FEC_RXD1 0x0
+				MX27_PAD_ATA_DATA4__FEC_RXD2 0x0
+				MX27_PAD_ATA_DATA5__FEC_RXD3 0x0
+				MX27_PAD_ATA_DATA6__FEC_MDIO 0x0
+				MX27_PAD_ATA_DATA7__FEC_MDC 0x0
+				MX27_PAD_ATA_DATA8__FEC_CRS 0x0
+				MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x0
+				MX27_PAD_ATA_DATA10__FEC_RXD0 0x0
+				MX27_PAD_ATA_DATA11__FEC_RX_DV 0x0
+				MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x0
+				MX27_PAD_ATA_DATA13__FEC_COL 0x0
+				MX27_PAD_ATA_DATA14__FEC_TX_ER 0x0
+				MX27_PAD_ATA_DATA15__FEC_TX_EN 0x0
+				MX27_PAD_SSI3_TXDAT__GPIO3_30	0x0 /* FEC RST */
+			>;
+		};
+
+		pinctrl_i2c2: i2c2grp {
+			fsl,pins = <
+				MX27_PAD_I2C2_SDA__I2C2_SDA 0x0
+				MX27_PAD_I2C2_SCL__I2C2_SCL 0x0
+			>;
+		};
+
+		pinctrl_nfc: nfcgrp {
+			fsl,pins = <
+				MX27_PAD_NFRB__NFRB 0x0
+				MX27_PAD_NFCLE__NFCLE 0x0
+				MX27_PAD_NFWP_B__NFWP_B 0x0
+				MX27_PAD_NFCE_B__NFCE_B 0x0
+				MX27_PAD_NFALE__NFALE 0x0
+				MX27_PAD_NFRE_B__NFRE_B 0x0
+				MX27_PAD_NFWE_B__NFWE_B 0x0
+			>;
+		};
+
+		pinctrl_usbotg: usbotggrp {
+			fsl,pins = <
+				MX27_PAD_USBOTG_CLK__USBOTG_CLK 0x0
+				MX27_PAD_USBOTG_DIR__USBOTG_DIR 0x0
+				MX27_PAD_USBOTG_NXT__USBOTG_NXT 0x0
+				MX27_PAD_USBOTG_STP__USBOTG_STP 0x0
+				MX27_PAD_USBOTG_DATA0__USBOTG_DATA0 0x0
+				MX27_PAD_USBOTG_DATA1__USBOTG_DATA1 0x0
+				MX27_PAD_USBOTG_DATA2__USBOTG_DATA2 0x0
+				MX27_PAD_USBOTG_DATA3__USBOTG_DATA3 0x0
+				MX27_PAD_USBOTG_DATA4__USBOTG_DATA4 0x0
+				MX27_PAD_USBOTG_DATA5__USBOTG_DATA5 0x0
+				MX27_PAD_USBOTG_DATA6__USBOTG_DATA6 0x0
+				MX27_PAD_USBOTG_DATA7__USBOTG_DATA7 0x0
+			>;
+		};
+	};
+};
+
 &nfc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_nfc>;
 	nand-bus-width = <8>;
 	nand-ecc-mode = "hw";
+	nand-on-flash-bbt;
 	status = "okay";
 };
 
-&uart1 {
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	dr_mode = "otg";
+	phy_type = "ulpi";
+	vbus-supply = <&sw3_reg>;
 	status = "okay";
 };
 
+&usbphy0 {
+	vcc-supply = <&sw3_reg>;
+};
+
 &weim {
 	status = "okay";
 

arch/arm/boot/dts/imx27-pinfunc.h

@@ -0,0 +1,526 @@
+/*
+ * Copyright 2013 Markus Pargmann <mpa@pengutronix.de>, Pengutronix
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#ifndef __DTS_IMX27_PINFUNC_H
+#define __DTS_IMX27_PINFUNC_H
+
+/*
+ * The pin function ID is a tuple of
+ * <pin mux_id>
+ * mux_id consists of
+ * function + (direction << 2) + (gpio_oconf << 4) + (gpio_iconfa << 8) + (gpio_iconfb << 10)
+ *
+ * function:      0 - Primary function
+ *                1 - Alternate function
+ *                2 - GPIO
+ * direction:     0 - Input
+ *                1 - Output
+ * gpio_oconf:    0 - A_IN
+ *                1 - B_IN
+ *                2 - C_IN
+ *                3 - Data Register
+ * gpio_iconfa/b: 0 - GPIO_IN
+ *                1 - Interrupt Status Register
+ *                2 - 0
+ *                3 - 1
+ *
+ * 'pin' is an integer between 0 and 0xbf. imx27 has 6 ports with 32 configurable
+ * configurable pins each. 'pin' is PORT * 32 + PORT_PIN, PORT_PIN is the pin
+ * number on the specific port (between 0 and 31).
+ */
+
+#define MX27_PAD_USBH2_CLK__USBH2_CLK                      0x00 0x000
+#define MX27_PAD_USBH2_CLK__GPIO1_0                        0x00 0x032
+#define MX27_PAD_USBH2_DIR__USBH2_DIR                      0x01 0x000
+#define MX27_PAD_USBH2_DIR__GPIO1_1                        0x01 0x032
+#define MX27_PAD_USBH2_DATA7__USBH2_DATA7                  0x02 0x004
+#define MX27_PAD_USBH2_DATA7__GPIO1_2                      0x02 0x032
+#define MX27_PAD_USBH2_NXT__USBH2_NXT                      0x03 0x000
+#define MX27_PAD_USBH2_NXT__GPIO1_3                        0x03 0x032
+#define MX27_PAD_USBH2_STP__USBH2_STP                      0x04 0x004
+#define MX27_PAD_USBH2_STP__GPIO1_4                        0x04 0x032
+#define MX27_PAD_LSCLK__LSCLK                              0x05 0x004
+#define MX27_PAD_LSCLK__GPIO1_5                            0x05 0x032
+#define MX27_PAD_LD0__LD0                                  0x06 0x004
+#define MX27_PAD_LD0__GPIO1_6                              0x06 0x032
+#define MX27_PAD_LD1__LD1                                  0x07 0x004
+#define MX27_PAD_LD1__GPIO1_7                              0x07 0x032
+#define MX27_PAD_LD2__LD2                                  0x08 0x004
+#define MX27_PAD_LD2__GPIO1_8                              0x08 0x032
+#define MX27_PAD_LD3__LD3                                  0x09 0x004
+#define MX27_PAD_LD3__GPIO1_9                              0x09 0x032
+#define MX27_PAD_LD4__LD4                                  0x0a 0x004
+#define MX27_PAD_LD4__GPIO1_10                             0x0a 0x032
+#define MX27_PAD_LD5__LD5                                  0x0b 0x004
+#define MX27_PAD_LD5__GPIO1_11                             0x0b 0x032
+#define MX27_PAD_LD6__LD6                                  0x0c 0x004
+#define MX27_PAD_LD6__GPIO1_12                             0x0c 0x032
+#define MX27_PAD_LD7__LD7                                  0x0d 0x004
+#define MX27_PAD_LD7__GPIO1_13                             0x0d 0x032
+#define MX27_PAD_LD8__LD8                                  0x0e 0x004
+#define MX27_PAD_LD8__GPIO1_14                             0x0e 0x032
+#define MX27_PAD_LD9__LD9                                  0x0f 0x004
+#define MX27_PAD_LD9__GPIO1_15                             0x0f 0x032
+#define MX27_PAD_LD10__LD10                                0x10 0x004
+#define MX27_PAD_LD10__GPIO1_16                            0x10 0x032
+#define MX27_PAD_LD11__LD11                                0x11 0x004
+#define MX27_PAD_LD11__GPIO1_17                            0x11 0x032
+#define MX27_PAD_LD12__LD12                                0x12 0x004
+#define MX27_PAD_LD12__GPIO1_18                            0x12 0x032
+#define MX27_PAD_LD13__LD13                                0x13 0x004
+#define MX27_PAD_LD13__GPIO1_19                            0x13 0x032
+#define MX27_PAD_LD14__LD14                                0x14 0x004
+#define MX27_PAD_LD14__GPIO1_20                            0x14 0x032
+#define MX27_PAD_LD15__LD15                                0x15 0x004
+#define MX27_PAD_LD15__GPIO1_21                            0x15 0x032
+#define MX27_PAD_LD16__LD16                                0x16 0x004
+#define MX27_PAD_LD16__GPIO1_22                            0x16 0x032
+#define MX27_PAD_LD17__LD17                                0x17 0x004
+#define MX27_PAD_LD17__GPIO1_23                            0x17 0x032
+#define MX27_PAD_REV__REV                                  0x18 0x004
+#define MX27_PAD_REV__GPIO1_24                             0x18 0x032
+#define MX27_PAD_CLS__CLS                                  0x19 0x004
+#define MX27_PAD_CLS__GPIO1_25                             0x19 0x032
+#define MX27_PAD_PS__PS                                    0x1a 0x004
+#define MX27_PAD_PS__GPIO1_26                              0x1a 0x032
+#define MX27_PAD_SPL_SPR__SPL_SPR                          0x1b 0x004
+#define MX27_PAD_SPL_SPR__GPIO1_27                         0x1b 0x032
+#define MX27_PAD_HSYNC__HSYNC                              0x1c 0x004
+#define MX27_PAD_HSYNC__GPIO1_28                           0x1c 0x032
+#define MX27_PAD_VSYNC__VSYNC                              0x1d 0x004
+#define MX27_PAD_VSYNC__GPIO1_29                           0x1d 0x032
+#define MX27_PAD_CONTRAST__CONTRAST                        0x1e 0x004
+#define MX27_PAD_CONTRAST__GPIO1_30                        0x1e 0x032
+#define MX27_PAD_OE_ACD__OE_ACD                            0x1f 0x004
+#define MX27_PAD_OE_ACD__GPIO1_31                          0x1f 0x032
+#define MX27_PAD_UNUSED0__UNUSED0                          0x20 0x004
+#define MX27_PAD_UNUSED0__GPIO2_0                          0x20 0x032
+#define MX27_PAD_UNUSED1__UNUSED1                          0x21 0x004
+#define MX27_PAD_UNUSED1__GPIO2_1                          0x21 0x032
+#define MX27_PAD_UNUSED2__UNUSED2                          0x22 0x004
+#define MX27_PAD_UNUSED2__GPIO2_2                          0x22 0x032
+#define MX27_PAD_UNUSED3__UNUSED3                          0x23 0x004
+#define MX27_PAD_UNUSED3__GPIO2_3                          0x23 0x032
+#define MX27_PAD_SD2_D0__SD2_D0                            0x24 0x004
+#define MX27_PAD_SD2_D0__MSHC_DATA0                        0x24 0x005
+#define MX27_PAD_SD2_D0__GPIO2_4                           0x24 0x032
+#define MX27_PAD_SD2_D1__SD2_D1                            0x25 0x004
+#define MX27_PAD_SD2_D1__MSHC_DATA1                        0x25 0x005
+#define MX27_PAD_SD2_D1__GPIO2_5                           0x25 0x032
+#define MX27_PAD_SD2_D2__SD2_D2                            0x26 0x004
+#define MX27_PAD_SD2_D2__MSHC_DATA2                        0x26 0x005
+#define MX27_PAD_SD2_D2__GPIO2_6                           0x26 0x032
+#define MX27_PAD_SD2_D3__SD2_D3                            0x27 0x004
+#define MX27_PAD_SD2_D3__MSHC_DATA3                        0x27 0x005
+#define MX27_PAD_SD2_D3__GPIO2_7                           0x27 0x032
+#define MX27_PAD_SD2_CMD__SD2_CMD                          0x28 0x004
+#define MX27_PAD_SD2_CMD__MSHC_BS                          0x28 0x005
+#define MX27_PAD_SD2_CMD__GPIO2_8                          0x28 0x032
+#define MX27_PAD_SD2_CLK__SD2_CLK                          0x29 0x004
+#define MX27_PAD_SD2_CLK__MSHC_SCLK                        0x29 0x005
+#define MX27_PAD_SD2_CLK__GPIO2_9                          0x29 0x032
+#define MX27_PAD_CSI_D0__CSI_D0                            0x2a 0x000
+#define MX27_PAD_CSI_D0__UART6_TXD                         0x2a 0x005
+#define MX27_PAD_CSI_D0__GPIO2_10                          0x2a 0x032
+#define MX27_PAD_CSI_D1__CSI_D1                            0x2b 0x000
+#define MX27_PAD_CSI_D1__UART6_RXD                         0x2b 0x001
+#define MX27_PAD_CSI_D1__GPIO2_11                          0x2b 0x032
+#define MX27_PAD_CSI_D2__CSI_D2                            0x2c 0x000
+#define MX27_PAD_CSI_D2__UART6_CTS                         0x2c 0x005
+#define MX27_PAD_CSI_D2__GPIO2_12                          0x2c 0x032
+#define MX27_PAD_CSI_D3__CSI_D3                            0x2d 0x000
+#define MX27_PAD_CSI_D3__UART6_RTS                         0x2d 0x001
+#define MX27_PAD_CSI_D3__GPIO2_13                          0x2d 0x032
+#define MX27_PAD_CSI_D4__CSI_D4                            0x2e 0x000
+#define MX27_PAD_CSI_D4__GPIO2_14                          0x2e 0x032
+#define MX27_PAD_CSI_MCLK__CSI_MCLK                        0x2f 0x004
+#define MX27_PAD_CSI_MCLK__GPIO2_15                        0x2f 0x032
+#define MX27_PAD_CSI_PIXCLK__CSI_PIXCLK                    0x30 0x000
+#define MX27_PAD_CSI_PIXCLK__GPIO2_16                      0x30 0x032
+#define MX27_PAD_CSI_D5__CSI_D5                            0x31 0x000
+#define MX27_PAD_CSI_D5__GPIO2_17                          0x31 0x032
+#define MX27_PAD_CSI_D6__CSI_D6                            0x32 0x000
+#define MX27_PAD_CSI_D6__UART5_TXD                         0x32 0x005
+#define MX27_PAD_CSI_D6__GPIO2_18                          0x32 0x032
+#define MX27_PAD_CSI_D7__CSI_D7                            0x33 0x000
+#define MX27_PAD_CSI_D7__UART5_RXD                         0x33 0x001
+#define MX27_PAD_CSI_D7__GPIO2_19                          0x33 0x032
+#define MX27_PAD_CSI_VSYNC__CSI_VSYNC                      0x34 0x000
+#define MX27_PAD_CSI_VSYNC__UART5_CTS                      0x34 0x005
+#define MX27_PAD_CSI_VSYNC__GPIO2_20                       0x34 0x032
+#define MX27_PAD_CSI_HSYNC__CSI_HSYNC                      0x35 0x000
+#define MX27_PAD_CSI_HSYNC__UART5_RTS                      0x35 0x001
+#define MX27_PAD_CSI_HSYNC__GPIO2_21                       0x35 0x032
+#define MX27_PAD_USBH1_SUSP__USBH1_SUSP                    0x36 0x004
+#define MX27_PAD_USBH1_SUSP__GPIO2_22                      0x36 0x032
+#define MX27_PAD_USB_PWR__USB_PWR                          0x37 0x004
+#define MX27_PAD_USB_PWR__GPIO2_23                         0x37 0x032
+#define MX27_PAD_USB_OC_B__USB_OC_B                        0x38 0x000
+#define MX27_PAD_USB_OC_B__GPIO2_24                        0x38 0x032
+#define MX27_PAD_USBH1_RCV__USBH1_RCV                      0x39 0x004
+#define MX27_PAD_USBH1_RCV__GPIO2_25                       0x39 0x032
+#define MX27_PAD_USBH1_FS__USBH1_FS                        0x3a 0x004
+#define MX27_PAD_USBH1_FS__UART4_RTS                       0x3a 0x001
+#define MX27_PAD_USBH1_FS__GPIO2_26                        0x3a 0x032
+#define MX27_PAD_USBH1_OE_B__USBH1_OE_B                    0x3b 0x004
+#define MX27_PAD_USBH1_OE_B__GPIO2_27                      0x3b 0x032
+#define MX27_PAD_USBH1_TXDM__USBH1_TXDM                    0x3c 0x004
+#define MX27_PAD_USBH1_TXDM__UART4_TXD                     0x3c 0x005
+#define MX27_PAD_USBH1_TXDM__GPIO2_28                      0x3c 0x032
+#define MX27_PAD_USBH1_TXDP__USBH1_TXDP                    0x3d 0x004
+#define MX27_PAD_USBH1_TXDP__UART4_CTS                     0x3d 0x005
+#define MX27_PAD_USBH1_TXDP__GPIO2_29                      0x3d 0x032
+#define MX27_PAD_USBH1_RXDM__USBH1_RXDM                    0x3e 0x004
+#define MX27_PAD_USBH1_RXDM__GPIO2_30                      0x3e 0x032
+#define MX27_PAD_USBH1_RXDP__USBH1_RXDP                    0x3f 0x004
+#define MX27_PAD_USBH1_RXDP__UART4_RXD                     0x3f 0x001
+#define MX27_PAD_USBH1_RXDP__GPIO2_31                      0x3f 0x032
+#define MX27_PAD_UNUSED4__UNUSED4                          0x40 0x004
+#define MX27_PAD_UNUSED4__GPIO3_0                          0x40 0x032
+#define MX27_PAD_UNUSED5__UNUSED5                          0x41 0x004
+#define MX27_PAD_UNUSED5__GPIO3_1                          0x41 0x032
+#define MX27_PAD_UNUSED6__UNUSED6                          0x42 0x004
+#define MX27_PAD_UNUSED6__GPIO3_2                          0x42 0x032
+#define MX27_PAD_UNUSED7__UNUSED7                          0x43 0x004
+#define MX27_PAD_UNUSED7__GPIO3_3                          0x43 0x032
+#define MX27_PAD_UNUSED8__UNUSED8                          0x44 0x004
+#define MX27_PAD_UNUSED8__GPIO3_4                          0x44 0x032
+#define MX27_PAD_I2C2_SDA__I2C2_SDA                        0x45 0x004
+#define MX27_PAD_I2C2_SDA__GPIO3_5                         0x45 0x032
+#define MX27_PAD_I2C2_SCL__I2C2_SCL                        0x46 0x004
+#define MX27_PAD_I2C2_SCL__GPIO3_6                         0x46 0x032
+#define MX27_PAD_USBOTG_DATA5__USBOTG_DATA5                0x47 0x004
+#define MX27_PAD_USBOTG_DATA5__GPIO3_7                     0x47 0x032
+#define MX27_PAD_USBOTG_DATA6__USBOTG_DATA6                0x48 0x004
+#define MX27_PAD_USBOTG_DATA6__GPIO3_8                     0x48 0x032
+#define MX27_PAD_USBOTG_DATA0__USBOTG_DATA0                0x49 0x004
+#define MX27_PAD_USBOTG_DATA0__GPIO3_9                     0x49 0x032
+#define MX27_PAD_USBOTG_DATA2__USBOTG_DATA2                0x4a 0x004
+#define MX27_PAD_USBOTG_DATA2__GPIO3_10                    0x4a 0x032
+#define MX27_PAD_USBOTG_DATA1__USBOTG_DATA1                0x4b 0x004
+#define MX27_PAD_USBOTG_DATA1__GPIO3_11                    0x4b 0x032
+#define MX27_PAD_USBOTG_DATA4__USBOTG_DATA4                0x4c 0x004
+#define MX27_PAD_USBOTG_DATA4__GPIO3_12                    0x4c 0x032
+#define MX27_PAD_USBOTG_DATA3__USBOTG_DATA3                0x4d 0x004
+#define MX27_PAD_USBOTG_DATA3__GPIO3_13                    0x4d 0x032
+#define MX27_PAD_TOUT__TOUT                                0x4e 0x004
+#define MX27_PAD_TOUT__GPIO3_14                            0x4e 0x032
+#define MX27_PAD_TIN__TIN                                  0x4f 0x000
+#define MX27_PAD_TIN__GPIO3_15                             0x4f 0x032
+#define MX27_PAD_SSI4_FS__SSI4_FS                          0x50 0x004
+#define MX27_PAD_SSI4_FS__GPIO3_16                         0x50 0x032
+#define MX27_PAD_SSI4_RXDAT__SSI4_RXDAT                    0x51 0x004
+#define MX27_PAD_SSI4_RXDAT__GPIO3_17                      0x51 0x032
+#define MX27_PAD_SSI4_TXDAT__SSI4_TXDAT                    0x52 0x004
+#define MX27_PAD_SSI4_TXDAT__GPIO3_18                      0x52 0x032
+#define MX27_PAD_SSI4_CLK__SSI4_CLK                        0x53 0x004
+#define MX27_PAD_SSI4_CLK__GPIO3_19                        0x53 0x032
+#define MX27_PAD_SSI1_FS__SSI1_FS                          0x54 0x004
+#define MX27_PAD_SSI1_FS__GPIO3_20                         0x54 0x032
+#define MX27_PAD_SSI1_RXDAT__SSI1_RXDAT                    0x55 0x004
+#define MX27_PAD_SSI1_RXDAT__GPIO3_21                      0x55 0x032
+#define MX27_PAD_SSI1_TXDAT__SSI1_TXDAT                    0x56 0x004
+#define MX27_PAD_SSI1_TXDAT__GPIO3_22                      0x56 0x032
+#define MX27_PAD_SSI1_CLK__SSI1_CLK                        0x57 0x004
+#define MX27_PAD_SSI1_CLK__GPIO3_23                        0x57 0x032
+#define MX27_PAD_SSI2_FS__SSI2_FS                          0x58 0x004
+#define MX27_PAD_SSI2_FS__GPT5_TOUT                        0x58 0x005
+#define MX27_PAD_SSI2_FS__GPIO3_24                         0x58 0x032
+#define MX27_PAD_SSI2_RXDAT__SSI2_RXDAT                    0x59 0x004
+#define MX27_PAD_SSI2_RXDAT__GPTS_TIN                      0x59 0x001
+#define MX27_PAD_SSI2_RXDAT__GPIO3_25                      0x59 0x032
+#define MX27_PAD_SSI2_TXDAT__SSI2_TXDAT                    0x5a 0x004
+#define MX27_PAD_SSI2_TXDAT__GPT4_TOUT                     0x5a 0x005
+#define MX27_PAD_SSI2_TXDAT__GPIO3_26                      0x5a 0x032
+#define MX27_PAD_SSI2_CLK__SSI2_CLK                        0x5b 0x004
+#define MX27_PAD_SSI2_CLK__GPT4_TIN                        0x5b 0x001
+#define MX27_PAD_SSI2_CLK__GPIO3_27                        0x5b 0x032
+#define MX27_PAD_SSI3_FS__SSI3_FS                          0x5c 0x004
+#define MX27_PAD_SSI3_FS__SLCDC2_D0                        0x5c 0x001
+#define MX27_PAD_SSI3_FS__GPIO3_28                         0x5c 0x032
+#define MX27_PAD_SSI3_RXDAT__SSI3_RXDAT                    0x5d 0x004
+#define MX27_PAD_SSI3_RXDAT__SLCDC2_RS                     0x5d 0x001
+#define MX27_PAD_SSI3_RXDAT__GPIO3_29                      0x5d 0x032
+#define MX27_PAD_SSI3_TXDAT__SSI3_TXDAT                    0x5e 0x004
+#define MX27_PAD_SSI3_TXDAT__SLCDC2_CS                     0x5e 0x001
+#define MX27_PAD_SSI3_TXDAT__GPIO3_30                      0x5e 0x032
+#define MX27_PAD_SSI3_CLK__SSI3_CLK                        0x5f 0x004
+#define MX27_PAD_SSI3_CLK__SLCDC2_CLK                      0x5f 0x001
+#define MX27_PAD_SSI3_CLK__GPIO3_31                        0x5f 0x032
+#define MX27_PAD_SD3_CMD__SD3_CMD                          0x60 0x004
+#define MX27_PAD_SD3_CMD__FEC_TXD0                         0x60 0x006
+#define MX27_PAD_SD3_CMD__GPIO4_0                          0x60 0x032
+#define MX27_PAD_SD3_CLK__SD3_CLK                          0x61 0x004
+#define MX27_PAD_SD3_CLK__ETMTRACEPKT15                    0x61 0x005
+#define MX27_PAD_SD3_CLK__FEC_TXD1                         0x61 0x006
+#define MX27_PAD_SD3_CLK__GPIO4_1                          0x61 0x032
+#define MX27_PAD_ATA_DATA0__ATA_DATA0                      0x62 0x004
+#define MX27_PAD_ATA_DATA0__SD3_D0                         0x62 0x005
+#define MX27_PAD_ATA_DATA0__FEC_TXD2                       0x62 0x006
+#define MX27_PAD_ATA_DATA0__GPIO4_2                        0x62 0x032
+#define MX27_PAD_ATA_DATA1__ATA_DATA1                      0x63 0x004
+#define MX27_PAD_ATA_DATA1__SD3_D1                         0x63 0x005
+#define MX27_PAD_ATA_DATA1__FEC_TXD3                       0x63 0x006
+#define MX27_PAD_ATA_DATA1__GPIO4_3                        0x63 0x032
+#define MX27_PAD_ATA_DATA2__ATA_DATA2                      0x64 0x004
+#define MX27_PAD_ATA_DATA2__SD3_D2                         0x64 0x005
+#define MX27_PAD_ATA_DATA2__FEC_RX_ER                      0x64 0x002
+#define MX27_PAD_ATA_DATA2__GPIO4_4                        0x64 0x032
+#define MX27_PAD_ATA_DATA3__ATA_DATA3                      0x65 0x004
+#define MX27_PAD_ATA_DATA3__SD3_D3                         0x65 0x005
+#define MX27_PAD_ATA_DATA3__FEC_RXD1                       0x65 0x002
+#define MX27_PAD_ATA_DATA3__GPIO4_5                        0x65 0x032
+#define MX27_PAD_ATA_DATA4__ATA_DATA4                      0x66 0x004
+#define MX27_PAD_ATA_DATA4__ETMTRACEPKT14                  0x66 0x005
+#define MX27_PAD_ATA_DATA4__FEC_RXD2                       0x66 0x002
+#define MX27_PAD_ATA_DATA4__GPIO4_6                        0x66 0x032
+#define MX27_PAD_ATA_DATA5__ATA_DATA5                      0x67 0x004
+#define MX27_PAD_ATA_DATA5__ETMTRACEPKT13                  0x67 0x005
+#define MX27_PAD_ATA_DATA5__FEC_RXD3                       0x67 0x002
+#define MX27_PAD_ATA_DATA5__GPIO4_7                        0x67 0x032
+#define MX27_PAD_ATA_DATA6__ATA_DATA6                      0x68 0x004
+#define MX27_PAD_ATA_DATA6__FEC_MDIO                       0x68 0x005
+#define MX27_PAD_ATA_DATA6__GPIO4_8                        0x68 0x032
+#define MX27_PAD_ATA_DATA7__ATA_DATA7                      0x69 0x004
+#define MX27_PAD_ATA_DATA7__ETMTRACEPKT12                  0x69 0x005
+#define MX27_PAD_ATA_DATA7__FEC_MDC                        0x69 0x006
+#define MX27_PAD_ATA_DATA7__GPIO4_9                        0x69 0x032
+#define MX27_PAD_ATA_DATA8__ATA_DATA8                      0x6a 0x004
+#define MX27_PAD_ATA_DATA8__ETMTRACEPKT11                  0x6a 0x005
+#define MX27_PAD_ATA_DATA8__FEC_CRS                        0x6a 0x002
+#define MX27_PAD_ATA_DATA8__GPIO4_10                       0x6a 0x032
+#define MX27_PAD_ATA_DATA9__ATA_DATA9                      0x6b 0x004
+#define MX27_PAD_ATA_DATA9__ETMTRACEPKT10                  0x6b 0x005
+#define MX27_PAD_ATA_DATA9__FEC_TX_CLK                     0x6b 0x002
+#define MX27_PAD_ATA_DATA9__GPIO4_11                       0x6b 0x032
+#define MX27_PAD_ATA_DATA10__ATA_DATA10                    0x6c 0x004
+#define MX27_PAD_ATA_DATA10__ETMTRACEPKT9                  0x6c 0x005
+#define MX27_PAD_ATA_DATA10__FEC_RXD0                      0x6c 0x002
+#define MX27_PAD_ATA_DATA10__GPIO4_12                      0x6c 0x032
+#define MX27_PAD_ATA_DATA11__ATA_DATA11                    0x6d 0x004
+#define MX27_PAD_ATA_DATA11__ETMTRACEPKT8                  0x6d 0x005
+#define MX27_PAD_ATA_DATA11__FEC_RX_DV                     0x6d 0x002
+#define MX27_PAD_ATA_DATA11__GPIO4_13                      0x6d 0x032
+#define MX27_PAD_ATA_DATA12__ATA_DATA12                    0x6e 0x004
+#define MX27_PAD_ATA_DATA12__ETMTRACEPKT7                  0x6e 0x005
+#define MX27_PAD_ATA_DATA12__FEC_RX_CLK                    0x6e 0x002
+#define MX27_PAD_ATA_DATA12__GPIO4_14                      0x6e 0x032
+#define MX27_PAD_ATA_DATA13__ATA_DATA13                    0x6f 0x004
+#define MX27_PAD_ATA_DATA13__ETMTRACEPKT6                  0x6f 0x005
+#define MX27_PAD_ATA_DATA13__FEC_COL                       0x6f 0x002
+#define MX27_PAD_ATA_DATA13__GPIO4_15                      0x6f 0x032
+#define MX27_PAD_ATA_DATA14__ATA_DATA14                    0x70 0x004
+#define MX27_PAD_ATA_DATA14__ETMTRACEPKT5                  0x70 0x005
+#define MX27_PAD_ATA_DATA14__FEC_TX_ER                     0x70 0x006
+#define MX27_PAD_ATA_DATA14__GPIO4_16                      0x70 0x032
+#define MX27_PAD_I2C_DATA__I2C_DATA                        0x71 0x004
+#define MX27_PAD_I2C_DATA__GPIO4_17                        0x71 0x032
+#define MX27_PAD_I2C_CLK__I2C_CLK                          0x72 0x004
+#define MX27_PAD_I2C_CLK__GPIO4_18                         0x72 0x032
+#define MX27_PAD_CSPI2_SS2__CSPI2_SS2                      0x73 0x004
+#define MX27_PAD_CSPI2_SS2__USBH2_DATA4                    0x73 0x005
+#define MX27_PAD_CSPI2_SS2__GPIO4_19                       0x73 0x032
+#define MX27_PAD_CSPI2_SS1__CSPI2_SS1                      0x74 0x004
+#define MX27_PAD_CSPI2_SS1__USBH2_DATA3                    0x74 0x005
+#define MX27_PAD_CSPI2_SS1__GPIO4_20                       0x74 0x032
+#define MX27_PAD_CSPI2_SS0__CSPI2_SS0                      0x75 0x004
+#define MX27_PAD_CSPI2_SS0__USBH2_DATA6                    0x75 0x005
+#define MX27_PAD_CSPI2_SS0__GPIO4_21                       0x75 0x032
+#define MX27_PAD_CSPI2_SCLK__CSPI2_SCLK                    0x76 0x004
+#define MX27_PAD_CSPI2_SCLK__USBH2_DATA0                   0x76 0x005
+#define MX27_PAD_CSPI2_SCLK__GPIO4_22                      0x76 0x032
+#define MX27_PAD_CSPI2_MISO__CSPI2_MISO                    0x77 0x004
+#define MX27_PAD_CSPI2_MISO__USBH2_DATA2                   0x77 0x005
+#define MX27_PAD_CSPI2_MISO__GPIO4_23                      0x77 0x032
+#define MX27_PAD_CSPI2_MOSI__CSPI2_MOSI                    0x78 0x004
+#define MX27_PAD_CSPI2_MOSI__USBH2_DATA1                   0x78 0x005
+#define MX27_PAD_CSPI2_MOSI__GPIO4_24                      0x78 0x032
+#define MX27_PAD_CSPI1_RDY__CSPI1_RDY                      0x79 0x000
+#define MX27_PAD_CSPI1_RDY__GPIO4_25                       0x79 0x032
+#define MX27_PAD_CSPI1_SS2__CSPI1_SS2                      0x7a 0x004
+#define MX27_PAD_CSPI1_SS2__USBH2_DATA5                    0x7a 0x005
+#define MX27_PAD_CSPI1_SS2__GPIO4_26                       0x7a 0x032
+#define MX27_PAD_CSPI1_SS1__CSPI1_SS1                      0x7b 0x004
+#define MX27_PAD_CSPI1_SS1__GPIO4_27                       0x7b 0x032
+#define MX27_PAD_CSPI1_SS0__CSPI1_SS0                      0x7c 0x004
+#define MX27_PAD_CSPI1_SS0__GPIO4_28                       0x7c 0x032
+#define MX27_PAD_CSPI1_SCLK__CSPI1_SCLK                    0x7d 0x004
+#define MX27_PAD_CSPI1_SCLK__GPIO4_29                      0x7d 0x032
+#define MX27_PAD_CSPI1_MISO__CSPI1_MISO                    0x7e 0x004
+#define MX27_PAD_CSPI1_MISO__GPIO4_30                      0x7e 0x032
+#define MX27_PAD_CSPI1_MOSI__CSPI1_MOSI                    0x7f 0x004
+#define MX27_PAD_CSPI1_MOSI__GPIO4_31                      0x7f 0x032
+#define MX27_PAD_USBOTG_NXT__USBOTG_NXT                    0x80 0x000
+#define MX27_PAD_USBOTG_NXT__KP_COL6A                      0x80 0x005
+#define MX27_PAD_USBOTG_NXT__GPIO5_0                       0x80 0x032
+#define MX27_PAD_USBOTG_STP__USBOTG_STP                    0x81 0x004
+#define MX27_PAD_USBOTG_STP__KP_ROW6A                      0x81 0x005
+#define MX27_PAD_USBOTG_STP__GPIO5_1                       0x81 0x032
+#define MX27_PAD_USBOTG_DIR__USBOTG_DIR                    0x82 0x000
+#define MX27_PAD_USBOTG_DIR__KP_ROW7A                      0x82 0x005
+#define MX27_PAD_USBOTG_DIR__GPIO5_2                       0x82 0x032
+#define MX27_PAD_UART2_CTS__UART2_CTS                      0x83 0x004
+#define MX27_PAD_UART2_CTS__KP_COL7                        0x83 0x005
+#define MX27_PAD_UART2_CTS__GPIO5_3                        0x83 0x032
+#define MX27_PAD_UART2_RTS__UART2_RTS                      0x84 0x000
+#define MX27_PAD_UART2_RTS__KP_ROW7                        0x84 0x005
+#define MX27_PAD_UART2_RTS__GPIO5_4                        0x84 0x032
+#define MX27_PAD_PWMO__PWMO                                0x85 0x004
+#define MX27_PAD_PWMO__GPIO5_5                             0x85 0x032
+#define MX27_PAD_UART2_TXD__UART2_TXD                      0x86 0x004
+#define MX27_PAD_UART2_TXD__KP_COL6                        0x86 0x005
+#define MX27_PAD_UART2_TXD__GPIO5_6                        0x86 0x032
+#define MX27_PAD_UART2_RXD__UART2_RXD                      0x87 0x000
+#define MX27_PAD_UART2_RXD__KP_ROW6                        0x87 0x005
+#define MX27_PAD_UART2_RXD__GPIO5_7                        0x87 0x032
+#define MX27_PAD_UART3_TXD__UART3_TXD                      0x88 0x004
+#define MX27_PAD_UART3_TXD__GPIO5_8                        0x88 0x032
+#define MX27_PAD_UART3_RXD__UART3_RXD                      0x89 0x000
+#define MX27_PAD_UART3_RXD__GPIO5_9                        0x89 0x032
+#define MX27_PAD_UART3_CTS__UART3_CTS                      0x8a 0x004
+#define MX27_PAD_UART3_CTS__GPIO5_10                       0x8a 0x032
+#define MX27_PAD_UART3_RTS__UART3_RTS                      0x8b 0x000
+#define MX27_PAD_UART3_RTS__GPIO5_11                       0x8b 0x032
+#define MX27_PAD_UART1_TXD__UART1_TXD                      0x8c 0x004
+#define MX27_PAD_UART1_TXD__GPIO5_12                       0x8c 0x032
+#define MX27_PAD_UART1_RXD__UART1_RXD                      0x8d 0x000
+#define MX27_PAD_UART1_RXD__GPIO5_13                       0x8d 0x032
+#define MX27_PAD_UART1_CTS__UART1_CTS                      0x8e 0x004
+#define MX27_PAD_UART1_CTS__GPIO5_14                       0x8e 0x032
+#define MX27_PAD_UART1_RTS__UART1_RTS                      0x8f 0x000
+#define MX27_PAD_UART1_RTS__GPIO5_15                       0x8f 0x032
+#define MX27_PAD_RTCK__RTCK                                0x90 0x004
+#define MX27_PAD_RTCK__OWIRE                               0x90 0x005
+#define MX27_PAD_RTCK__GPIO5_16                            0x90 0x032
+#define MX27_PAD_RESET_OUT_B__RESET_OUT_B                  0x91 0x004
+#define MX27_PAD_RESET_OUT_B__GPIO5_17                     0x91 0x032
+#define MX27_PAD_SD1_D0__SD1_D0                            0x92 0x004
+#define MX27_PAD_SD1_D0__CSPI3_MISO                        0x92 0x001
+#define MX27_PAD_SD1_D0__GPIO5_18                          0x92 0x032
+#define MX27_PAD_SD1_D1__SD1_D1                            0x93 0x004
+#define MX27_PAD_SD1_D1__GPIO5_19                          0x93 0x032
+#define MX27_PAD_SD1_D2__SD1_D2                            0x94 0x004
+#define MX27_PAD_SD1_D2__GPIO5_20                          0x94 0x032
+#define MX27_PAD_SD1_D3__SD1_D3                            0x95 0x004
+#define MX27_PAD_SD1_D3__CSPI3_SS                          0x95 0x005
+#define MX27_PAD_SD1_D3__GPIO5_21                          0x95 0x032
+#define MX27_PAD_SD1_CMD__SD1_CMD                          0x96 0x004
+#define MX27_PAD_SD1_CMD__CSPI3_MOSI                       0x96 0x005
+#define MX27_PAD_SD1_CMD__GPIO5_22                         0x96 0x032
+#define MX27_PAD_SD1_CLK__SD1_CLK                          0x97 0x004
+#define MX27_PAD_SD1_CLK__CSPI3_SCLK                       0x97 0x005
+#define MX27_PAD_SD1_CLK__GPIO5_23                         0x97 0x032
+#define MX27_PAD_USBOTG_CLK__USBOTG_CLK                    0x98 0x000
+#define MX27_PAD_USBOTG_CLK__GPIO5_24                      0x98 0x032
+#define MX27_PAD_USBOTG_DATA7__USBOTG_DATA7                0x99 0x004
+#define MX27_PAD_USBOTG_DATA7__GPIO5_25                    0x99 0x032
+#define MX27_PAD_UNUSED9__UNUSED9                          0x9a 0x004
+#define MX27_PAD_UNUSED9__GPIO5_26                         0x9a 0x032
+#define MX27_PAD_UNUSED10__UNUSED10                        0x9b 0x004
+#define MX27_PAD_UNUSED10__GPIO5_27                        0x9b 0x032
+#define MX27_PAD_UNUSED11__UNUSED11                        0x9c 0x004
+#define MX27_PAD_UNUSED11__GPIO5_28                        0x9c 0x032
+#define MX27_PAD_UNUSED12__UNUSED12                        0x9d 0x004
+#define MX27_PAD_UNUSED12__GPIO5_29                        0x9d 0x032
+#define MX27_PAD_UNUSED13__UNUSED13                        0x9e 0x004
+#define MX27_PAD_UNUSED13__GPIO5_30                        0x9e 0x032
+#define MX27_PAD_UNUSED14__UNUSED14                        0x9f 0x004
+#define MX27_PAD_UNUSED14__GPIO5_31                        0x9f 0x032
+#define MX27_PAD_NFRB__NFRB                                0xa0 0x000
+#define MX27_PAD_NFRB__ETMTRACEPKT3                        0xa0 0x005
+#define MX27_PAD_NFRB__GPIO6_0                             0xa0 0x032
+#define MX27_PAD_NFCLE__NFCLE                              0xa1 0x004
+#define MX27_PAD_NFCLE__ETMTRACEPKT0                       0xa1 0x005
+#define MX27_PAD_NFCLE__GPIO6_1                            0xa1 0x032
+#define MX27_PAD_NFWP_B__NFWP_B                            0xa2 0x004
+#define MX27_PAD_NFWP_B__ETMTRACEPKT1                      0xa2 0x005
+#define MX27_PAD_NFWP_B__GPIO6_2                           0xa2 0x032
+#define MX27_PAD_NFCE_B__NFCE_B                            0xa3 0x004
+#define MX27_PAD_NFCE_B__ETMTRACEPKT2                      0xa3 0x005
+#define MX27_PAD_NFCE_B__GPIO6_3                           0xa3 0x032
+#define MX27_PAD_NFALE__NFALE                              0xa4 0x004
+#define MX27_PAD_NFALE__ETMPIPESTAT0                       0xa4 0x005
+#define MX27_PAD_NFALE__GPIO6_4                            0xa4 0x032
+#define MX27_PAD_NFRE_B__NFRE_B                            0xa5 0x004
+#define MX27_PAD_NFRE_B__ETMPIPESTAT1                      0xa5 0x005
+#define MX27_PAD_NFRE_B__GPIO6_5                           0xa5 0x032
+#define MX27_PAD_NFWE_B__NFWE_B                            0xa6 0x004
+#define MX27_PAD_NFWE_B__ETMPIPESTAT2                      0xa6 0x005
+#define MX27_PAD_NFWE_B__GPIO6_6                           0xa6 0x032
+#define MX27_PAD_PC_POE__PC_POE                            0xa7 0x004
+#define MX27_PAD_PC_POE__ATA_BUFFER_EN                     0xa7 0x005
+#define MX27_PAD_PC_POE__GPIO6_7                           0xa7 0x032
+#define MX27_PAD_PC_RW_B__PC_RW_B                          0xa8 0x004
+#define MX27_PAD_PC_RW_B__ATA_IORDY                        0xa8 0x001
+#define MX27_PAD_PC_RW_B__GPIO6_8                          0xa8 0x032
+#define MX27_PAD_IOIS16__IOIS16                            0xa9 0x000
+#define MX27_PAD_IOIS16__ATA_INTRQ                         0xa9 0x001
+#define MX27_PAD_IOIS16__GPIO6_9                           0xa9 0x032
+#define MX27_PAD_PC_RST__PC_RST                            0xaa 0x004
+#define MX27_PAD_PC_RST__ATA_RESET_B                       0xaa 0x005
+#define MX27_PAD_PC_RST__GPIO6_10                          0xaa 0x032
+#define MX27_PAD_PC_BVD2__PC_BVD2                          0xab 0x000
+#define MX27_PAD_PC_BVD2__ATA_DMACK                        0xab 0x005
+#define MX27_PAD_PC_BVD2__GPIO6_11                         0xab 0x032
+#define MX27_PAD_PC_BVD1__PC_BVD1                          0xac 0x000
+#define MX27_PAD_PC_BVD1__ATA_DMARQ                        0xac 0x001
+#define MX27_PAD_PC_BVD1__GPIO6_12                         0xac 0x032
+#define MX27_PAD_PC_VS2__PC_VS2                            0xad 0x000
+#define MX27_PAD_PC_VS2__ATA_DA0                           0xad 0x005
+#define MX27_PAD_PC_VS2__GPIO6_13                          0xad 0x032
+#define MX27_PAD_PC_VS1__PC_VS1                            0xae 0x000
+#define MX27_PAD_PC_VS1__ATA_DA1                           0xae 0x005
+#define MX27_PAD_PC_VS1__GPIO6_14                          0xae 0x032
+#define MX27_PAD_CLKO__CLKO                                0xaf 0x004
+#define MX27_PAD_CLKO__GPIO6_15                            0xaf 0x032
+#define MX27_PAD_PC_PWRON__PC_PWRON                        0xb0 0x000
+#define MX27_PAD_PC_PWRON__ATA_DA2                         0xb0 0x005
+#define MX27_PAD_PC_PWRON__GPIO6_16                        0xb0 0x032
+#define MX27_PAD_PC_READY__PC_READY                        0xb1 0x000
+#define MX27_PAD_PC_READY__ATA_CS0                         0xb1 0x005
+#define MX27_PAD_PC_READY__GPIO6_17                        0xb1 0x032
+#define MX27_PAD_PC_WAIT_B__PC_WAIT_B                      0xb2 0x000
+#define MX27_PAD_PC_WAIT_B__ATA_CS1                        0xb2 0x005
+#define MX27_PAD_PC_WAIT_B__GPIO6_18                       0xb2 0x032
+#define MX27_PAD_PC_CD2_B__PC_CD2_B                        0xb3 0x000
+#define MX27_PAD_PC_CD2_B__ATA_DIOW                        0xb3 0x005
+#define MX27_PAD_PC_CD2_B__GPIO6_19                        0xb3 0x032
+#define MX27_PAD_PC_CD1_B__PC_CD1_B                        0xb4 0x000
+#define MX27_PAD_PC_CD1_B__ATA_DIOR                        0xb4 0x005
+#define MX27_PAD_PC_CD1_B__GPIO6_20                        0xb4 0x032
+#define MX27_PAD_CS4_B__CS4_B                              0xb5 0x004
+#define MX27_PAD_CS4_B__ETMTRACESYNC                       0xb5 0x005
+#define MX27_PAD_CS4_B__GPIO6_21                           0xb5 0x032
+#define MX27_PAD_CS5_B__CS5_B                              0xb6 0x004
+#define MX27_PAD_CS5_B__ETMTRACECLK                        0xb6 0x005
+#define MX27_PAD_CS5_B__GPIO6_22                           0xb6 0x032
+#define MX27_PAD_ATA_DATA15__ATA_DATA15                    0xb7 0x004
+#define MX27_PAD_ATA_DATA15__ETMTRACEPKT4                  0xb7 0x005
+#define MX27_PAD_ATA_DATA15__FEC_TX_EN                     0xb7 0x006
+#define MX27_PAD_ATA_DATA15__GPIO6_23                      0xb7 0x032
+#define MX27_PAD_UNUSED15__UNUSED15                        0xb8 0x004
+#define MX27_PAD_UNUSED15__GPIO6_24                        0xb8 0x032
+#define MX27_PAD_UNUSED16__UNUSED16                        0xb9 0x004
+#define MX27_PAD_UNUSED16__GPIO6_25                        0xb9 0x032
+#define MX27_PAD_UNUSED17__UNUSED17                        0xba 0x004
+#define MX27_PAD_UNUSED17__GPIO6_26                        0xba 0x032
+#define MX27_PAD_UNUSED18__UNUSED18                        0xbb 0x004
+#define MX27_PAD_UNUSED18__GPIO6_27                        0xbb 0x032
+#define MX27_PAD_UNUSED19__UNUSED19                        0xbc 0x004
+#define MX27_PAD_UNUSED19__GPIO6_28                        0xbc 0x032
+#define MX27_PAD_UNUSED20__UNUSED20                        0xbd 0x004
+#define MX27_PAD_UNUSED20__GPIO6_29                        0xbd 0x032
+#define MX27_PAD_UNUSED21__UNUSED21                        0xbe 0x004
+#define MX27_PAD_UNUSED21__GPIO6_30                        0xbe 0x032
+#define MX27_PAD_UNUSED22__UNUSED22                        0xbf 0x004
+#define MX27_PAD_UNUSED22__GPIO6_31                        0xbf 0x032
+
+#endif /* __DTS_IMX27_PINFUNC_H */

arch/arm/boot/dts/imx27.dtsi

@@ -10,6 +10,9 @@
  */
 
 #include "skeleton.dtsi"
+#include "imx27-pinfunc.h"
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	aliases {
@@ -67,6 +70,26 @@
 		};
 	};
 
+	usbphy {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usbphy0: usbphy@0 {
+			compatible = "usb-nop-xceiv";
+			reg = <0>;
+			clocks = <&clks 75>;
+			clock-names = "main_clk";
+		};
+
+		usbphy2: usbphy@2 {
+			compatible = "usb-nop-xceiv";
+			reg = <2>;
+			clocks = <&clks 75>;
+			clock-names = "main_clk";
+		};
+	};
+
 	soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -204,6 +227,30 @@
 				status = "disabled";
 			};
 
+			ssi1: ssi@10010000 {
+				#sound-dai-cells = <0>;
+				compatible = "fsl,imx27-ssi", "fsl,imx21-ssi";
+				reg = <0x10010000 0x1000>;
+				interrupts = <14>;
+				clocks = <&clks 26>;
+				dmas = <&dma 12>, <&dma 13>, <&dma 14>, <&dma 15>;
+				dma-names = "rx0", "tx0", "rx1", "tx1";
+				fsl,fifo-depth = <8>;
+				status = "disabled";
+			};
+
+			ssi2: ssi@10011000 {
+				#sound-dai-cells = <0>;
+				compatible = "fsl,imx27-ssi", "fsl,imx21-ssi";
+				reg = <0x10011000 0x1000>;
+				interrupts = <13>;
+				clocks = <&clks 25>;
+				dmas = <&dma 8>, <&dma 9>, <&dma 10>, <&dma 11>;
+				dma-names = "rx0", "tx0", "rx1", "tx1";
+				fsl,fifo-depth = <8>;
+				status = "disabled";
+			};
+
 			i2c1: i2c@10012000 {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -236,64 +283,72 @@
 				status = "disabled";
 			};
 
-			gpio1: gpio@10015000 {
-				compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
-				reg = <0x10015000 0x100>;
-				interrupts = <8>;
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpio2: gpio@10015100 {
-				compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
-				reg = <0x10015100 0x100>;
-				interrupts = <8>;
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpio3: gpio@10015200 {
-				compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
-				reg = <0x10015200 0x100>;
-				interrupts = <8>;
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpio4: gpio@10015300 {
-				compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
-				reg = <0x10015300 0x100>;
-				interrupts = <8>;
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpio5: gpio@10015400 {
-				compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
-				reg = <0x10015400 0x100>;
-				interrupts = <8>;
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-			};
-
-			gpio6: gpio@10015500 {
-				compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
-				reg = <0x10015500 0x100>;
-				interrupts = <8>;
-				gpio-controller;
-				#gpio-cells = <2>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
+			iomuxc: iomuxc@10015000 {
+				compatible = "fsl,imx27-iomuxc";
+				reg = <0x10015000 0x600>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges;
+
+				gpio1: gpio@10015000 {
+					compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
+					reg = <0x10015000 0x100>;
+					interrupts = <8>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				gpio2: gpio@10015100 {
+					compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
+					reg = <0x10015100 0x100>;
+					interrupts = <8>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				gpio3: gpio@10015200 {
+					compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
+					reg = <0x10015200 0x100>;
+					interrupts = <8>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				gpio4: gpio@10015300 {
+					compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
+					reg = <0x10015300 0x100>;
+					interrupts = <8>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				gpio5: gpio@10015400 {
+					compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
+					reg = <0x10015400 0x100>;
+					interrupts = <8>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				gpio6: gpio@10015500 {
+					compatible = "fsl,imx27-gpio", "fsl,imx21-gpio";
+					reg = <0x10015500 0x100>;
+					interrupts = <8>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
 			};
 
 			audmux: audmux@10016000 {
@@ -404,6 +459,42 @@
 				iram = <&iram>;
 			};
 
+			usbotg: usb@10024000 {
+				compatible = "fsl,imx27-usb";
+				reg = <0x10024000 0x200>;
+				interrupts = <56>;
+				clocks = <&clks 15>;
+				fsl,usbmisc = <&usbmisc 0>;
+				fsl,usbphy = <&usbphy0>;
+				status = "disabled";
+			};
+
+			usbh1: usb@10024200 {
+				compatible = "fsl,imx27-usb";
+				reg = <0x10024200 0x200>;
+				interrupts = <54>;
+				clocks = <&clks 15>;
+				fsl,usbmisc = <&usbmisc 1>;
+				status = "disabled";
+			};
+
+			usbh2: usb@10024400 {
+				compatible = "fsl,imx27-usb";
+				reg = <0x10024400 0x200>;
+				interrupts = <55>;
+				clocks = <&clks 15>;
+				fsl,usbmisc = <&usbmisc 2>;
+				fsl,usbphy = <&usbphy2>;
+				status = "disabled";
+			};
+
+			usbmisc: usbmisc@10024600 {
+				#index-cells = <1>;
+				compatible = "fsl,imx27-usbmisc";
+				reg = <0x10024600 0x200>;
+				clocks = <&clks 62>;
+			};
+
 			sahara2: sahara@10025000 {
 				compatible = "fsl,imx27-sahara";
 				reg = <0x10025000 0x1000>;

arch/arm/boot/dts/imx28-apf28dev.dts

@@ -48,6 +48,7 @@
 						MX28_PAD_LCD_D20__GPIO_1_20
 						MX28_PAD_LCD_D21__GPIO_1_21
 						MX28_PAD_LCD_D22__GPIO_1_22
+						MX28_PAD_GPMI_CE1N__GPIO_0_17
 					>;
 					fsl,drive-strength = <MXS_DRIVE_4mA>;
 					fsl,voltage = <MXS_VOLTAGE_HIGH>;
@@ -66,6 +67,16 @@
 					fsl,voltage = <MXS_VOLTAGE_HIGH>;
 					fsl,pull-up = <MXS_PULL_DISABLE>;
 				};
+
+				usb0_otg_apf28dev: otg-apf28dev@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <
+						MX28_PAD_LCD_D23__GPIO_1_23
+					>;
+					fsl,drive-strength = <MXS_DRIVE_4mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
+				};
 			};
 
 			lcdif@80030000 {
@@ -131,6 +142,8 @@
 
 	ahb@80080000 {
 		usb0: usb@80080000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&usb0_otg_apf28dev>;
 			vbus-supply = <&reg_usb0_vbus>;
 			status = "okay";
 		};
@@ -150,13 +163,17 @@
 
 	regulators {
 		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		reg_usb0_vbus: usb0_vbus {
+		reg_usb0_vbus: regulator@0 {
 			compatible = "regulator-fixed";
+			reg = <0>;
 			regulator-name = "usb0_vbus";
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio1 23 1>;
+			enable-active-high;
 		};
 	};
 
@@ -177,4 +194,14 @@
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
 	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-button {
+			label = "User button";
+			gpios = <&gpio0 17 0>;
+			linux,code = <0x100>;
+		};
+	};
 };

arch/arm/boot/dts/imx28-apx4devkit.dts

@@ -193,9 +193,12 @@
 
 	regulators {
 		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-		reg_3p3v: 3p3v {
+		reg_3p3v: regulator@0 {
 			compatible = "regulator-fixed";
+			reg = <0>;
 			regulator-name = "3P3V";
 			regulator-min-microvolt = <3300000>;
 			regulator-max-microvolt = <3300000>;