net: emaclite: update kernel-doc comments

This patch fixes below kernel-doc warnings:

Function parameter or member 'maxlen' not described in 'xemaclite_recv_data'
Function parameter or member 'address'not described in 'xemaclite_set_mac_address'
Excess function parameter 'addr' description in 'xemaclite_set_mac_address'
No description found for return value of 'xemaclite_interrupt'
No description found for return value of 'xemaclite_mdio_write'
Function parameter or member 'dev' not described in 'xemaclite_mdio_setup'
Excess function parameter 'ofdev' description in 'xemaclite_mdio_setup'
No description found for return value of 'xemaclite_open'
No description found for return value of 'xemaclite_close'
Excess function parameter 'match' description in 'xemaclite_of_probe'

Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/xilinx/xilinx_emaclite.c

@@ -369,6 +369,7 @@ static int xemaclite_send_data(struct net_local *drvdata, u8 *data,
  * xemaclite_recv_data - Receive a frame
  * @drvdata:	Pointer to the Emaclite device private data
  * @data:	Address where the data is to be received
+ * @maxlen:    Maximum supported ethernet packet length
  *
  * This function is intended to be called from the interrupt context or
  * with a wrapper which waits for the receive frame to be available.
@@ -488,7 +489,7 @@ static void xemaclite_update_address(struct net_local *drvdata,
 /**
  * xemaclite_set_mac_address - Set the MAC address for this device
  * @dev:	Pointer to the network device instance
- * @addr:	Void pointer to the sockaddr structure
+ * @address:	Void pointer to the sockaddr structure
  *
  * This function copies the HW address from the sockaddr strucutre to the
  * net_device structure and updates the address in HW.
@@ -638,6 +639,8 @@ static void xemaclite_rx_handler(struct net_device *dev)
  * @dev_id:	Void pointer to the network device instance used as callback
  *		reference
  *
+ * Return:	IRQ_HANDLED
+ *
  * This function handles the Tx and Rx interrupts of the EmacLite device.
  */
 static irqreturn_t xemaclite_interrupt(int irq, void *dev_id)
@@ -771,6 +774,8 @@ static int xemaclite_mdio_read(struct mii_bus *bus, int phy_id, int reg)
  *
  * This function waits till the device is ready to accept a new MDIO
  * request and then writes the val to the MDIO Write Data register.
+ *
+ * Return:      0 upon success or a negative error upon failure
  */
 static int xemaclite_mdio_write(struct mii_bus *bus, int phy_id, int reg,
 				u16 val)
@@ -804,7 +809,7 @@ static int xemaclite_mdio_write(struct mii_bus *bus, int phy_id, int reg,
 /**
  * xemaclite_mdio_setup - Register mii_bus for the Emaclite device
  * @lp:		Pointer to the Emaclite device private data
- * @ofdev:	Pointer to OF device structure
+ * @dev:	Pointer to OF device structure
  *
  * This function enables MDIO bus in the Emaclite device and registers a
  * mii_bus.
@@ -904,6 +909,9 @@ static void xemaclite_adjust_link(struct net_device *ndev)
  * This function sets the MAC address, requests an IRQ and enables interrupts
  * for the Emaclite device and starts the Tx queue.
  * It also connects to the phy device, if MDIO is included in Emaclite device.
+ *
+ * Return:	0 on success. -ENODEV, if PHY cannot be connected.
+ *		Non-zero error value on failure.
  */
 static int xemaclite_open(struct net_device *dev)
 {
@@ -974,6 +982,8 @@ static int xemaclite_open(struct net_device *dev)
  * This function stops the Tx queue, disables interrupts and frees the IRQ for
  * the Emaclite device.
  * It also disconnects the phy device associated with the Emaclite device.
+ *
+ * Return:	0, always.
  */
 static int xemaclite_close(struct net_device *dev)
 {
@@ -1064,7 +1074,6 @@ static const struct net_device_ops xemaclite_netdev_ops;
 /**
  * xemaclite_of_probe - Probe method for the Emaclite device.
  * @ofdev:	Pointer to OF device structure
- * @match:	Pointer to the structure used for matching a device
  *
  * This function probes for the Emaclite device in the device tree.
  * It initializes the driver data structure and the hardware, sets the MAC