Merge tag 'omap-for-v4.5/wakeup-m3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers

TI wakeup M3 IPC device driver for v4.5 merge window. This driver will
eventually allow am33xx and am437x to support PM with their Cortex-M3
power management processor.

This driver has been waiting to get merged for quite a while but has
had dependencies to the remoteproc that are now out of the way.

* tag 'omap-for-v4.5/wakeup-m3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  soc: ti: Add wkup_m3_ipc driver
  Documentation: dt: add bindings for TI Wakeup M3 IPC device

Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/soc/ti/wkup_m3_ipc.txt

@@ -0,0 +1,57 @@
+Wakeup M3 IPC Driver
+=====================
+
+The TI AM33xx and AM43xx family of devices use a small Cortex M3 co-processor
+(commonly referred to as Wakeup M3 or CM3) to help with various low power tasks
+that cannot be controlled from the MPU, like suspend/resume and certain deep
+C-states for CPU Idle. Once the wkup_m3_ipc driver uses the wkup_m3_rproc driver
+to boot the wkup_m3, it handles communication with the CM3 using IPC registers
+present in the SoC's control module and a mailbox. The wkup_m3_ipc exposes an
+API to allow the SoC PM code to execute specific PM tasks.
+
+Wkup M3 Device Node:
+====================
+A wkup_m3_ipc device node is used to represent the IPC registers within an
+SoC.
+
+Required properties:
+--------------------
+- compatible:		Should be,
+				"ti,am3352-wkup-m3-ipc" for AM33xx SoCs
+				"ti,am4372-wkup-m3-ipc" for AM43xx SoCs
+- reg:			Contains the IPC register address space to communicate
+			with the Wakeup M3 processor
+- interrupts:		Contains the interrupt information for the wkup_m3
+			interrupt that signals the MPU.
+- ti,rproc:		phandle to the wkup_m3 rproc node so the IPC driver
+			can boot it.
+- mboxes:		phandles used by IPC framework to get correct mbox
+			channel for communication. Must point to appropriate
+			mbox_wkupm3 child node.
+
+Example:
+--------
+/* AM33xx */
+	l4_wkup: l4_wkup@44c00000 {
+		...
+
+		scm: scm@210000 {
+			compatible = "ti,am3-scm", "simple-bus";
+			reg = <0x210000 0x2000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x210000 0x2000>;
+
+			...
+
+			wkup_m3_ipc: wkup_m3_ipc@1324 {
+				compatible = "ti,am3352-wkup-m3-ipc";
+				reg = <0x1324 0x24>;
+				interrupts = <78>;
+				ti,rproc = <&wkup_m3>;
+				mboxes = <&mailbox &mbox_wkupm3>;
+			};
+
+			...
+		};
+	};

drivers/soc/ti/Kconfig

@@ -28,4 +28,14 @@ config KEYSTONE_NAVIGATOR_DMA
 
 	  If unsure, say N.
 
+config WKUP_M3_IPC
+	tristate "TI AMx3 Wkup-M3 IPC Driver"
+	depends on WKUP_M3_RPROC
+	depends on OMAP2PLUS_MBOX
+	help
+	  TI AM33XX and AM43XX have a Cortex M3, the Wakeup M3, to handle
+	  low power transitions. This IPC driver provides the necessary API
+	  to communicate and use the Wakeup M3 for PM features like suspend
+	  resume and boots it using wkup_m3_rproc driver.
+
 endif # SOC_TI

drivers/soc/ti/Makefile

@@ -4,3 +4,4 @@
 obj-$(CONFIG_KEYSTONE_NAVIGATOR_QMSS)	+= knav_qmss.o
 knav_qmss-y := knav_qmss_queue.o knav_qmss_acc.o
 obj-$(CONFIG_KEYSTONE_NAVIGATOR_DMA)	+= knav_dma.o
+obj-$(CONFIG_WKUP_M3_IPC)		+= wkup_m3_ipc.o

drivers/soc/ti/wkup_m3_ipc.c

@@ -0,0 +1,508 @@
+/*
+ * AMx3 Wkup M3 IPC driver
+ *
+ * Copyright (C) 2015 Texas Instruments, Inc.
+ *
+ * Dave Gerlach <d-gerlach@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/kthread.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/omap-mailbox.h>
+#include <linux/platform_device.h>
+#include <linux/remoteproc.h>
+#include <linux/suspend.h>
+#include <linux/wkup_m3_ipc.h>
+
+#define AM33XX_CTRL_IPC_REG_COUNT	0x8
+#define AM33XX_CTRL_IPC_REG_OFFSET(m)	(0x4 + 4 * (m))
+
+/* AM33XX M3_TXEV_EOI register */
+#define AM33XX_CONTROL_M3_TXEV_EOI	0x00
+
+#define AM33XX_M3_TXEV_ACK		(0x1 << 0)
+#define AM33XX_M3_TXEV_ENABLE		(0x0 << 0)
+
+#define IPC_CMD_DS0			0x4
+#define IPC_CMD_STANDBY			0xc
+#define IPC_CMD_IDLE			0x10
+#define IPC_CMD_RESET			0xe
+#define DS_IPC_DEFAULT			0xffffffff
+#define M3_VERSION_UNKNOWN		0x0000ffff
+#define M3_BASELINE_VERSION		0x191
+#define M3_STATUS_RESP_MASK		(0xffff << 16)
+#define M3_FW_VERSION_MASK		0xffff
+
+#define M3_STATE_UNKNOWN		0
+#define M3_STATE_RESET			1
+#define M3_STATE_INITED			2
+#define M3_STATE_MSG_FOR_LP		3
+#define M3_STATE_MSG_FOR_RESET		4
+
+static struct wkup_m3_ipc *m3_ipc_state;
+
+static void am33xx_txev_eoi(struct wkup_m3_ipc *m3_ipc)
+{
+	writel(AM33XX_M3_TXEV_ACK,
+	       m3_ipc->ipc_mem_base + AM33XX_CONTROL_M3_TXEV_EOI);
+}
+
+static void am33xx_txev_enable(struct wkup_m3_ipc *m3_ipc)
+{
+	writel(AM33XX_M3_TXEV_ENABLE,
+	       m3_ipc->ipc_mem_base + AM33XX_CONTROL_M3_TXEV_EOI);
+}
+
+static void wkup_m3_ctrl_ipc_write(struct wkup_m3_ipc *m3_ipc,
+				   u32 val, int ipc_reg_num)
+{
+	if (WARN(ipc_reg_num < 0 || ipc_reg_num > AM33XX_CTRL_IPC_REG_COUNT,
+		 "ipc register operation out of range"))
+		return;
+
+	writel(val, m3_ipc->ipc_mem_base +
+	       AM33XX_CTRL_IPC_REG_OFFSET(ipc_reg_num));
+}
+
+static unsigned int wkup_m3_ctrl_ipc_read(struct wkup_m3_ipc *m3_ipc,
+					  int ipc_reg_num)
+{
+	if (WARN(ipc_reg_num < 0 || ipc_reg_num > AM33XX_CTRL_IPC_REG_COUNT,
+		 "ipc register operation out of range"))
+		return 0;
+
+	return readl(m3_ipc->ipc_mem_base +
+		     AM33XX_CTRL_IPC_REG_OFFSET(ipc_reg_num));
+}
+
+static int wkup_m3_fw_version_read(struct wkup_m3_ipc *m3_ipc)
+{
+	int val;
+
+	val = wkup_m3_ctrl_ipc_read(m3_ipc, 2);
+
+	return val & M3_FW_VERSION_MASK;
+}
+
+static irqreturn_t wkup_m3_txev_handler(int irq, void *ipc_data)
+{
+	struct wkup_m3_ipc *m3_ipc = ipc_data;
+	struct device *dev = m3_ipc->dev;
+	int ver = 0;
+
+	am33xx_txev_eoi(m3_ipc);
+
+	switch (m3_ipc->state) {
+	case M3_STATE_RESET:
+		ver = wkup_m3_fw_version_read(m3_ipc);
+
+		if (ver == M3_VERSION_UNKNOWN ||
+		    ver < M3_BASELINE_VERSION) {
+			dev_warn(dev, "CM3 Firmware Version %x not supported\n",
+				 ver);
+		} else {
+			dev_info(dev, "CM3 Firmware Version = 0x%x\n", ver);
+		}
+
+		m3_ipc->state = M3_STATE_INITED;
+		complete(&m3_ipc->sync_complete);
+		break;
+	case M3_STATE_MSG_FOR_RESET:
+		m3_ipc->state = M3_STATE_INITED;
+		complete(&m3_ipc->sync_complete);
+		break;
+	case M3_STATE_MSG_FOR_LP:
+		complete(&m3_ipc->sync_complete);
+		break;
+	case M3_STATE_UNKNOWN:
+		dev_warn(dev, "Unknown CM3 State\n");
+	}
+
+	am33xx_txev_enable(m3_ipc);
+
+	return IRQ_HANDLED;
+}
+
+static int wkup_m3_ping(struct wkup_m3_ipc *m3_ipc)
+{
+	struct device *dev = m3_ipc->dev;
+	mbox_msg_t dummy_msg = 0;
+	int ret;
+
+	if (!m3_ipc->mbox) {
+		dev_err(dev,
+			"No IPC channel to communicate with wkup_m3!\n");
+		return -EIO;
+	}
+
+	/*
+	 * Write a dummy message to the mailbox in order to trigger the RX
+	 * interrupt to alert the M3 that data is available in the IPC
+	 * registers. We must enable the IRQ here and disable it after in
+	 * the RX callback to avoid multiple interrupts being received
+	 * by the CM3.
+	 */
+	ret = mbox_send_message(m3_ipc->mbox, &dummy_msg);
+	if (ret < 0) {
+		dev_err(dev, "%s: mbox_send_message() failed: %d\n",
+			__func__, ret);
+		return ret;
+	}
+
+	ret = wait_for_completion_timeout(&m3_ipc->sync_complete,
+					  msecs_to_jiffies(500));
+	if (!ret) {
+		dev_err(dev, "MPU<->CM3 sync failure\n");
+		m3_ipc->state = M3_STATE_UNKNOWN;
+		return -EIO;
+	}
+
+	mbox_client_txdone(m3_ipc->mbox, 0);
+	return 0;
+}
+
+static int wkup_m3_ping_noirq(struct wkup_m3_ipc *m3_ipc)
+{
+	struct device *dev = m3_ipc->dev;
+	mbox_msg_t dummy_msg = 0;
+	int ret;
+
+	if (!m3_ipc->mbox) {
+		dev_err(dev,
+			"No IPC channel to communicate with wkup_m3!\n");
+		return -EIO;
+	}
+
+	ret = mbox_send_message(m3_ipc->mbox, &dummy_msg);
+	if (ret < 0) {
+		dev_err(dev, "%s: mbox_send_message() failed: %d\n",
+			__func__, ret);
+		return ret;
+	}
+
+	mbox_client_txdone(m3_ipc->mbox, 0);
+	return 0;
+}
+
+static int wkup_m3_is_available(struct wkup_m3_ipc *m3_ipc)
+{
+	return ((m3_ipc->state != M3_STATE_RESET) &&
+		(m3_ipc->state != M3_STATE_UNKNOWN));
+}
+
+/* Public functions */
+/**
+ * wkup_m3_set_mem_type - Pass wkup_m3 which type of memory is in use
+ * @mem_type: memory type value read directly from emif
+ *
+ * wkup_m3 must know what memory type is in use to properly suspend
+ * and resume.
+ */
+static void wkup_m3_set_mem_type(struct wkup_m3_ipc *m3_ipc, int mem_type)
+{
+	m3_ipc->mem_type = mem_type;
+}
+
+/**
+ * wkup_m3_set_resume_address - Pass wkup_m3 resume address
+ * @addr: Physical address from which resume code should execute
+ */
+static void wkup_m3_set_resume_address(struct wkup_m3_ipc *m3_ipc, void *addr)
+{
+	m3_ipc->resume_addr = (unsigned long)addr;
+}
+
+/**
+ * wkup_m3_request_pm_status - Retrieve wkup_m3 status code after suspend
+ *
+ * Returns code representing the status of a low power mode transition.
+ *	0 - Successful transition
+ *	1 - Failure to transition to low power state
+ */
+static int wkup_m3_request_pm_status(struct wkup_m3_ipc *m3_ipc)
+{
+	unsigned int i;
+	int val;
+
+	val = wkup_m3_ctrl_ipc_read(m3_ipc, 1);
+
+	i = M3_STATUS_RESP_MASK & val;
+	i >>= __ffs(M3_STATUS_RESP_MASK);
+
+	return i;
+}
+
+/**
+ * wkup_m3_prepare_low_power - Request preparation for transition to
+ *			       low power state
+ * @state: A kernel suspend state to enter, either MEM or STANDBY
+ *
+ * Returns 0 if preparation was successful, otherwise returns error code
+ */
+static int wkup_m3_prepare_low_power(struct wkup_m3_ipc *m3_ipc, int state)
+{
+	struct device *dev = m3_ipc->dev;
+	int m3_power_state;
+	int ret = 0;
+
+	if (!wkup_m3_is_available(m3_ipc))
+		return -ENODEV;
+
+	switch (state) {
+	case WKUP_M3_DEEPSLEEP:
+		m3_power_state = IPC_CMD_DS0;
+		break;
+	case WKUP_M3_STANDBY:
+		m3_power_state = IPC_CMD_STANDBY;
+		break;
+	case WKUP_M3_IDLE:
+		m3_power_state = IPC_CMD_IDLE;
+		break;
+	default:
+		return 1;
+	}
+
+	/* Program each required IPC register then write defaults to others */
+	wkup_m3_ctrl_ipc_write(m3_ipc, m3_ipc->resume_addr, 0);
+	wkup_m3_ctrl_ipc_write(m3_ipc, m3_power_state, 1);
+	wkup_m3_ctrl_ipc_write(m3_ipc, m3_ipc->mem_type, 4);
+
+	wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 2);
+	wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 3);
+	wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 5);
+	wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 6);
+	wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 7);
+
+	m3_ipc->state = M3_STATE_MSG_FOR_LP;
+
+	if (state == WKUP_M3_IDLE)
+		ret = wkup_m3_ping_noirq(m3_ipc);
+	else
+		ret = wkup_m3_ping(m3_ipc);
+
+	if (ret) {
+		dev_err(dev, "Unable to ping CM3\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+/**
+ * wkup_m3_finish_low_power - Return m3 to reset state
+ *
+ * Returns 0 if reset was successful, otherwise returns error code
+ */
+static int wkup_m3_finish_low_power(struct wkup_m3_ipc *m3_ipc)
+{
+	struct device *dev = m3_ipc->dev;
+	int ret = 0;
+
+	if (!wkup_m3_is_available(m3_ipc))
+		return -ENODEV;
+
+	wkup_m3_ctrl_ipc_write(m3_ipc, IPC_CMD_RESET, 1);
+	wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 2);
+
+	m3_ipc->state = M3_STATE_MSG_FOR_RESET;
+
+	ret = wkup_m3_ping(m3_ipc);
+	if (ret) {
+		dev_err(dev, "Unable to ping CM3\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static struct wkup_m3_ipc_ops ipc_ops = {
+	.set_mem_type = wkup_m3_set_mem_type,
+	.set_resume_address = wkup_m3_set_resume_address,
+	.prepare_low_power = wkup_m3_prepare_low_power,
+	.finish_low_power = wkup_m3_finish_low_power,
+	.request_pm_status = wkup_m3_request_pm_status,
+};
+
+/**
+ * wkup_m3_ipc_get - Return handle to wkup_m3_ipc
+ *
+ * Returns NULL if the wkup_m3 is not yet available, otherwise returns
+ * pointer to wkup_m3_ipc struct.
+ */
+struct wkup_m3_ipc *wkup_m3_ipc_get(void)
+{
+	if (m3_ipc_state)
+		get_device(m3_ipc_state->dev);
+	else
+		return NULL;
+
+	return m3_ipc_state;
+}
+EXPORT_SYMBOL_GPL(wkup_m3_ipc_get);
+
+/**
+ * wkup_m3_ipc_put - Free handle to wkup_m3_ipc returned from wkup_m3_ipc_get
+ * @m3_ipc: A pointer to wkup_m3_ipc struct returned by wkup_m3_ipc_get
+ */
+void wkup_m3_ipc_put(struct wkup_m3_ipc *m3_ipc)
+{
+	if (m3_ipc_state)
+		put_device(m3_ipc_state->dev);
+}
+EXPORT_SYMBOL_GPL(wkup_m3_ipc_put);
+
+static void wkup_m3_rproc_boot_thread(struct wkup_m3_ipc *m3_ipc)
+{
+	struct device *dev = m3_ipc->dev;
+	int ret;
+
+	wait_for_completion(&m3_ipc->rproc->firmware_loading_complete);
+
+	init_completion(&m3_ipc->sync_complete);
+
+	ret = rproc_boot(m3_ipc->rproc);
+	if (ret)
+		dev_err(dev, "rproc_boot failed\n");
+
+	do_exit(0);
+}
+
+static int wkup_m3_ipc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	int irq, ret;
+	phandle rproc_phandle;
+	struct rproc *m3_rproc;
+	struct resource *res;
+	struct task_struct *task;
+	struct wkup_m3_ipc *m3_ipc;
+
+	m3_ipc = devm_kzalloc(dev, sizeof(*m3_ipc), GFP_KERNEL);
+	if (!m3_ipc)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	m3_ipc->ipc_mem_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(m3_ipc->ipc_mem_base)) {
+		dev_err(dev, "could not ioremap ipc_mem\n");
+		return PTR_ERR(m3_ipc->ipc_mem_base);
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (!irq) {
+		dev_err(&pdev->dev, "no irq resource\n");
+		return -ENXIO;
+	}
+
+	ret = devm_request_irq(dev, irq, wkup_m3_txev_handler,
+			       0, "wkup_m3_txev", m3_ipc);
+	if (ret) {
+		dev_err(dev, "request_irq failed\n");
+		return ret;
+	}
+
+	m3_ipc->mbox_client.dev = dev;
+	m3_ipc->mbox_client.tx_done = NULL;
+	m3_ipc->mbox_client.tx_prepare = NULL;
+	m3_ipc->mbox_client.rx_callback = NULL;
+	m3_ipc->mbox_client.tx_block = false;
+	m3_ipc->mbox_client.knows_txdone = false;
+
+	m3_ipc->mbox = mbox_request_channel(&m3_ipc->mbox_client, 0);
+
+	if (IS_ERR(m3_ipc->mbox)) {
+		dev_err(dev, "IPC Request for A8->M3 Channel failed! %ld\n",
+			PTR_ERR(m3_ipc->mbox));
+		return PTR_ERR(m3_ipc->mbox);
+	}
+
+	if (of_property_read_u32(dev->of_node, "ti,rproc", &rproc_phandle)) {
+		dev_err(&pdev->dev, "could not get rproc phandle\n");
+		ret = -ENODEV;
+		goto err_free_mbox;
+	}
+
+	m3_rproc = rproc_get_by_phandle(rproc_phandle);
+	if (!m3_rproc) {
+		dev_err(&pdev->dev, "could not get rproc handle\n");
+		ret = -EPROBE_DEFER;
+		goto err_free_mbox;
+	}
+
+	m3_ipc->rproc = m3_rproc;
+	m3_ipc->dev = dev;
+	m3_ipc->state = M3_STATE_RESET;
+
+	m3_ipc->ops = &ipc_ops;
+
+	/*
+	 * Wait for firmware loading completion in a thread so we
+	 * can boot the wkup_m3 as soon as it's ready without holding
+	 * up kernel boot
+	 */
+	task = kthread_run((void *)wkup_m3_rproc_boot_thread, m3_ipc,
+			   "wkup_m3_rproc_loader");
+
+	if (IS_ERR(task)) {
+		dev_err(dev, "can't create rproc_boot thread\n");
+		goto err_put_rproc;
+	}
+
+	m3_ipc_state = m3_ipc;
+
+	return 0;
+
+err_put_rproc:
+	rproc_put(m3_rproc);
+err_free_mbox:
+	mbox_free_channel(m3_ipc->mbox);
+	return ret;
+}
+
+static int wkup_m3_ipc_remove(struct platform_device *pdev)
+{
+	mbox_free_channel(m3_ipc_state->mbox);
+
+	rproc_shutdown(m3_ipc_state->rproc);
+	rproc_put(m3_ipc_state->rproc);
+
+	m3_ipc_state = NULL;
+
+	return 0;
+}
+
+static const struct of_device_id wkup_m3_ipc_of_match[] = {
+	{ .compatible = "ti,am3352-wkup-m3-ipc", },
+	{ .compatible = "ti,am4372-wkup-m3-ipc", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, wkup_m3_ipc_of_match);
+
+static struct platform_driver wkup_m3_ipc_driver = {
+	.probe = wkup_m3_ipc_probe,
+	.remove = wkup_m3_ipc_remove,
+	.driver = {
+		.name = "wkup_m3_ipc",
+		.of_match_table = wkup_m3_ipc_of_match,
+	},
+};
+
+module_platform_driver(wkup_m3_ipc_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("wkup m3 remote processor ipc driver");
+MODULE_AUTHOR("Dave Gerlach <d-gerlach@ti.com>");

include/linux/wkup_m3_ipc.h

@@ -0,0 +1,55 @@
+/*
+ * TI Wakeup M3 for AMx3 SoCs Power Management Routines
+ *
+ * Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com/
+ * Dave Gerlach <d-gerlach@ti.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _LINUX_WKUP_M3_IPC_H
+#define _LINUX_WKUP_M3_IPC_H
+
+#define WKUP_M3_DEEPSLEEP	1
+#define WKUP_M3_STANDBY		2
+#define WKUP_M3_IDLE		3
+
+#include <linux/mailbox_client.h>
+
+struct wkup_m3_ipc_ops;
+
+struct wkup_m3_ipc {
+	struct rproc *rproc;
+
+	void __iomem *ipc_mem_base;
+	struct device *dev;
+
+	int mem_type;
+	unsigned long resume_addr;
+	int state;
+
+	struct completion sync_complete;
+	struct mbox_client mbox_client;
+	struct mbox_chan *mbox;
+
+	struct wkup_m3_ipc_ops *ops;
+};
+
+struct wkup_m3_ipc_ops {
+	void (*set_mem_type)(struct wkup_m3_ipc *m3_ipc, int mem_type);
+	void (*set_resume_address)(struct wkup_m3_ipc *m3_ipc, void *addr);
+	int (*prepare_low_power)(struct wkup_m3_ipc *m3_ipc, int state);
+	int (*finish_low_power)(struct wkup_m3_ipc *m3_ipc);
+	int (*request_pm_status)(struct wkup_m3_ipc *m3_ipc);
+};
+
+struct wkup_m3_ipc *wkup_m3_ipc_get(void);
+void wkup_m3_ipc_put(struct wkup_m3_ipc *m3_ipc);
+#endif /* _LINUX_WKUP_M3_IPC_H */