scsi: lpfc: Memory allocation error during driver start-up on power8

The driver fails to allocate command buffers in the routine
lpfc_new_scsi_buf_s4

There is an inconsistency between lpfc_mem_alloc(), where the
phba->lpfc_sg_dma_buf_pool is created, and lpfc_new_scsi_buf_s4(),
when we allocate a buffer from the pool and check the alignment.  The
alignment should be on a page boundary, based on LPFC_SLI3_BG_ENABLED in
sli3_options, for both cases.

Fix by explicitly tracking sli4 vs sli3 and BG options.  The result is that
phba->cfg_sg_dma_buf_size is now set correctly for SLI-4.

Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

drivers/scsi/lpfc/lpfc_attr.c

@@ -6344,6 +6344,10 @@ lpfc_get_cfgparam(struct lpfc_hba *phba)
 		phba->cfg_poll = 0;
 	else
 		phba->cfg_poll = lpfc_poll;
+
+	if (phba->cfg_enable_bg)
+		phba->sli3_options |= LPFC_SLI3_BG_ENABLED;
+
 	lpfc_suppress_rsp_init(phba, lpfc_suppress_rsp);
 
 	lpfc_enable_fc4_type_init(phba, lpfc_enable_fc4_type);

drivers/scsi/lpfc/lpfc_init.c

@@ -5912,7 +5912,7 @@ lpfc_sli4_driver_resource_setup(struct lpfc_hba *phba)
 	 * Since lpfc_sg_seg_cnt is module param, the sg_dma_buf_size
 	 * used to create the sg_dma_buf_pool must be calculated.
 	 */
-	if (phba->cfg_enable_bg) {
+	if (phba->sli3_options & LPFC_SLI3_BG_ENABLED) {
 		/*
 		 * The scsi_buf for a T10-DIF I/O holds the FCP cmnd,
 		 * the FCP rsp, and a SGE. Sice we have no control

drivers/scsi/lpfc/lpfc_scsi.c

@@ -837,8 +837,13 @@ lpfc_new_scsi_buf_s4(struct lpfc_vport *vport, int num_to_alloc)
 		 * 4K Page alignment is CRITICAL to BlockGuard, double check
 		 * to be sure.
 		 */
-		if (phba->cfg_enable_bg  && (((unsigned long)(psb->data) &
+		if ((phba->sli3_options & LPFC_SLI3_BG_ENABLED) &&
+		    (((unsigned long)(psb->data) &
 		    (unsigned long)(SLI4_PAGE_SIZE - 1)) != 0)) {
+			lpfc_printf_log(phba, KERN_ERR, LOG_FCP,
+					"3369 Memory alignment error "
+					"addr=%lx\n",
+					(unsigned long)psb->data);
 			dma_pool_free(phba->lpfc_sg_dma_buf_pool,
 				      psb->data, psb->dma_handle);
 			kfree(psb);

drivers/scsi/lpfc/lpfc_sli.c

@@ -4993,13 +4993,14 @@ lpfc_sli_config_port(struct lpfc_hba *phba, int sli_mode)
 		phba->hbq_get = phba->mbox->us.s3_pgp.hbq_get;
 		phba->port_gp = phba->mbox->us.s3_pgp.port;
 
-		if (phba->cfg_enable_bg) {
-			if (pmb->u.mb.un.varCfgPort.gbg)
-				phba->sli3_options |= LPFC_SLI3_BG_ENABLED;
-			else
+		if (phba->sli3_options & LPFC_SLI3_BG_ENABLED) {
+			if (pmb->u.mb.un.varCfgPort.gbg == 0) {
+				phba->cfg_enable_bg = 0;
+				phba->sli3_options &= ~LPFC_SLI3_BG_ENABLED;
 				lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
 						"0443 Adapter did not grant "
 						"BlockGuard\n");
+			}
 		}
 	} else {
 		phba->hbq_get = NULL;
@@ -6991,12 +6992,12 @@ lpfc_sli4_hba_setup(struct lpfc_hba *phba)
 	 * then turn off the global config parameters to disable the
 	 * feature in the driver.  This is not a fatal error.
 	 */
-	phba->sli3_options &= ~LPFC_SLI3_BG_ENABLED;
-	if (phba->cfg_enable_bg) {
-		if (bf_get(lpfc_mbx_rq_ftr_rsp_dif, &mqe->un.req_ftrs))
-			phba->sli3_options |= LPFC_SLI3_BG_ENABLED;
-		else
+	if (phba->sli3_options & LPFC_SLI3_BG_ENABLED) {
+		if (!(bf_get(lpfc_mbx_rq_ftr_rsp_dif, &mqe->un.req_ftrs))) {
+			phba->cfg_enable_bg = 0;
+			phba->sli3_options &= ~LPFC_SLI3_BG_ENABLED;
 			ftr_rsp++;
+		}
 	}
 
 	if (phba->max_vpi && phba->cfg_enable_npiv &&