Merge tag 'nfs-rdma-for-4.1-1' of git://git.linux-nfs.org/projects/anna/nfs-rdma

NFS: NFSoRDMA Client Changes

This patch series creates an operation vector for each of the different
memory registration modes.  This should make it easier to one day increase
credit limit, rsize, and wsize.

Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>

Documentation/devicetree/bindings/arm/exynos/power_domain.txt

@@ -22,6 +22,8 @@ Optional Properties:
 	- pclkN, clkN: Pairs of parent of input clock and input clock to the
 		devices in this power domain. Maximum of 4 pairs (N = 0 to 3)
 		are supported currently.
+- power-domains: phandle pointing to the parent power domain, for more details
+		 see Documentation/devicetree/bindings/power/power_domain.txt
 
 Node of a device using power domains must have a power-domains property
 defined with a phandle to respective power domain.

Documentation/devicetree/bindings/arm/sti.txt

@@ -13,6 +13,10 @@ Boards with the ST STiH407 SoC shall have the following properties:
 Required root node property:
 compatible = "st,stih407";
 
+Boards with the ST STiH410 SoC shall have the following properties:
+Required root node property:
+compatible = "st,stih410";
+
 Boards with the ST STiH418 SoC shall have the following properties:
 Required root node property:
 compatible = "st,stih418";

Documentation/devicetree/bindings/net/apm-xgene-enet.txt

@@ -4,7 +4,10 @@ Ethernet nodes are defined to describe on-chip ethernet interfaces in
 APM X-Gene SoC.
 
 Required properties for all the ethernet interfaces:
-- compatible: Should be "apm,xgene-enet"
+- compatible: Should state binding information from the following list,
+  - "apm,xgene-enet":    RGMII based 1G interface
+  - "apm,xgene1-sgenet": SGMII based 1G interface
+  - "apm,xgene1-xgenet": XFI based 10G interface
 - reg: Address and length of the register set for the device. It contains the
   information of registers in the same order as described by reg-names
 - reg-names: Should contain the register set names

Documentation/devicetree/bindings/power/power_domain.txt

@@ -19,6 +19,16 @@ Required properties:
    providing multiple PM domains (e.g. power controllers), but can be any value
    as specified by device tree binding documentation of particular provider.
 
+Optional properties:
+ - power-domains : A phandle and PM domain specifier as defined by bindings of
+                   the power controller specified by phandle.
+   Some power domains might be powered from another power domain (or have
+   other hardware specific dependencies). For representing such dependency
+   a standard PM domain consumer binding is used. When provided, all domains
+   created by the given provider should be subdomains of the domain
+   specified by this binding. More details about power domain specifier are
+   available in the next section.
+
 Example:
 
 	power: power-controller@12340000 {
@@ -30,6 +40,25 @@ Example:
 The node above defines a power controller that is a PM domain provider and
 expects one cell as its phandle argument.
 
+Example 2:
+
+	parent: power-controller@12340000 {
+		compatible = "foo,power-controller";
+		reg = <0x12340000 0x1000>;
+		#power-domain-cells = <1>;
+	};
+
+	child: power-controller@12340000 {
+		compatible = "foo,power-controller";
+		reg = <0x12341000 0x1000>;
+		power-domains = <&parent 0>;
+		#power-domain-cells = <1>;
+	};
+
+The nodes above define two power controllers: 'parent' and 'child'.
+Domains created by the 'child' power controller are subdomains of '0' power
+domain provided by the 'parent' power controller.
+
 ==PM domain consumers==
 
 Required properties:

Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt

@@ -0,0 +1,19 @@
+ETRAX FS UART
+
+Required properties:
+- compatible : "axis,etraxfs-uart"
+- reg: offset and length of the register set for the device.
+- interrupts: device interrupt
+
+Optional properties:
+- {dtr,dsr,ri,cd}-gpios: specify a GPIO for DTR/DSR/RI/CD
+  line respectively.
+
+Example:
+
+serial@b00260000 {
+	compatible = "axis,etraxfs-uart";
+	reg = <0xb0026000 0x1000>;
+	interrupts = <68>;
+	status = "disabled";
+};

Documentation/devicetree/bindings/submitting-patches.txt

@@ -12,6 +12,9 @@ I. For patch submitters
 
        devicetree@vger.kernel.org
 
+     and Cc: the DT maintainers. Use scripts/get_maintainer.pl to identify
+     all of the DT maintainers.
+
   3) The Documentation/ portion of the patch should come in the series before
      the code implementing the binding.
 

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -20,6 +20,7 @@ amlogic	Amlogic, Inc.
 ams	AMS AG
 amstaos	AMS-Taos Inc.
 apm	Applied Micro Circuits Corporation (APM)
+arasan	Arasan Chip Systems
 arm	ARM Ltd.
 armadeus	ARMadeus Systems SARL
 asahi-kasei	Asahi Kasei Corp.
@@ -27,6 +28,7 @@ atmel	Atmel Corporation
 auo	AU Optronics Corporation
 avago	Avago Technologies
 avic	Shanghai AVIC Optoelectronics Co., Ltd.
+axis	Axis Communications AB
 bosch	Bosch Sensortec GmbH
 brcm	Broadcom Corporation
 buffalo	Buffalo, Inc.

Documentation/devicetree/bindings/watchdog/atmel-wdt.txt

@@ -26,6 +26,11 @@ Optional properties:
 - atmel,disable : Should be present if you want to disable the watchdog.
 - atmel,idle-halt : Should be present if you want to stop the watchdog when
 	entering idle state.
+	CAUTION: This property should be used with care, it actually makes the
+	watchdog not counting when the CPU is in idle state, therefore the
+	watchdog reset time depends on mean CPU usage and will not reset at all
+	if the CPU stop working while it is in idle state, which is probably
+	not what you want.
 - atmel,dbg-halt : Should be present if you want to stop the watchdog when
 	entering debug state.
 

MAINTAINERS

@@ -1030,6 +1030,16 @@ F:	arch/arm/mach-mxs/
 F:	arch/arm/boot/dts/imx*
 F:	arch/arm/configs/imx*_defconfig
 
+ARM/FREESCALE VYBRID ARM ARCHITECTURE
+M:	Shawn Guo <shawn.guo@linaro.org>
+M:	Sascha Hauer <kernel@pengutronix.de>
+R:	Stefan Agner <stefan@agner.ch>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
+F:	arch/arm/mach-imx/*vf610*
+F:	arch/arm/boot/dts/vf*
+
 ARM/GLOMATION GESBC9312SX MACHINE SUPPORT
 M:	Lennert Buytenhek <kernel@wantstofly.org>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -1176,7 +1186,7 @@ M:	Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/mach-mvebu/
-F:	drivers/rtc/armada38x-rtc
+F:	drivers/rtc/rtc-armada38x.c
 
 ARM/Marvell Berlin SoC support
 M:	Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
@@ -1188,6 +1198,7 @@ ARM/Marvell Dove/MV78xx0/Orion SOC support
 M:	Jason Cooper <jason@lakedaemon.net>
 M:	Andrew Lunn <andrew@lunn.ch>
 M:	Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
+M:	Gregory Clement <gregory.clement@free-electrons.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/mach-dove/
@@ -1351,6 +1362,7 @@ F:	drivers/i2c/busses/i2c-rk3x.c
 F:	drivers/*/*rockchip*
 F:	drivers/*/*/*rockchip*
 F:	sound/soc/rockchip/
+N:	rockchip
 
 ARM/SAMSUNG EXYNOS ARM ARCHITECTURES
 M:	Kukjin Kim <kgene@kernel.org>
@@ -1664,8 +1676,8 @@ F:	drivers/misc/eeprom/at24.c
 F:	include/linux/platform_data/at24.h
 
 ATA OVER ETHERNET (AOE) DRIVER
-M:	"Ed L. Cashin" <ecashin@coraid.com>
-W:	http://support.coraid.com/support/linux
+M:	"Ed L. Cashin" <ed.cashin@acm.org>
+W:	http://www.openaoe.org/
 S:	Supported
 F:	Documentation/aoe/
 F:	drivers/block/aoe/
@@ -1730,7 +1742,7 @@ S:	Maintained
 F:	drivers/net/ethernet/atheros/
 
 ATM
-M:	Chas Williams <chas@cmf.nrl.navy.mil>
+M:	Chas Williams <3chas3@gmail.com>
 L:	linux-atm-general@lists.sourceforge.net (moderated for non-subscribers)
 L:	netdev@vger.kernel.org
 W:	http://linux-atm.sourceforge.net
@@ -2107,7 +2119,6 @@ F:	drivers/net/ethernet/broadcom/bnx2x/
 
 BROADCOM BCM281XX/BCM11XXX/BCM216XX ARM ARCHITECTURE
 M:	Christian Daudt <bcm@fixthebug.org>
-M:	Matt Porter <mporter@linaro.org>
 M:	Florian Fainelli <f.fainelli@gmail.com>
 L:	bcm-kernel-feedback-list@broadcom.com
 T:	git git://github.com/broadcom/mach-bcm
@@ -2369,8 +2380,9 @@ F:	arch/x86/include/asm/tce.h
 
 CAN NETWORK LAYER
 M:	Oliver Hartkopp <socketcan@hartkopp.net>
+M:	Marc Kleine-Budde <mkl@pengutronix.de>
 L:	linux-can@vger.kernel.org
-W:	http://gitorious.org/linux-can
+W:	https://github.com/linux-can
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can.git
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next.git
 S:	Maintained
@@ -2386,7 +2398,7 @@ CAN NETWORK DRIVERS
 M:	Wolfgang Grandegger <wg@grandegger.com>
 M:	Marc Kleine-Budde <mkl@pengutronix.de>
 L:	linux-can@vger.kernel.org
-W:	http://gitorious.org/linux-can
+W:	https://github.com/linux-can
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can.git
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next.git
 S:	Maintained
@@ -3241,6 +3253,13 @@ S:	Maintained
 F:	Documentation/hwmon/dme1737
 F:	drivers/hwmon/dme1737.c
 
+DMI/SMBIOS SUPPORT
+M:	Jean Delvare <jdelvare@suse.de>
+S:	Maintained
+F:	drivers/firmware/dmi-id.c
+F:	drivers/firmware/dmi_scan.c
+F:	include/linux/dmi.h
+
 DOCKING STATION DRIVER
 M:	Shaohua Li <shaohua.li@intel.com>
 L:	linux-acpi@vger.kernel.org
@@ -10196,6 +10215,13 @@ S:	Maintained
 F:	Documentation/usb/ohci.txt
 F:	drivers/usb/host/ohci*
 
+USB OTG FSM (Finite State Machine)
+M:	Peter Chen <Peter.Chen@freescale.com>
+T:	git git://github.com/hzpeterchen/linux-usb.git
+L:	linux-usb@vger.kernel.org
+S:	Maintained
+F:	drivers/usb/common/usb-otg-fsm.c
+
 USB OVER IP DRIVER
 M:	Valentina Manea <valentina.manea.m@gmail.com>
 M:	Shuah Khan <shuah.kh@samsung.com>

Makefile

@@ -1,7 +1,7 @@
 VERSION = 4
 PATCHLEVEL = 0
 SUBLEVEL = 0
-EXTRAVERSION = -rc3
+EXTRAVERSION = -rc6
 NAME = Hurr durr I'ma sheep
 
 # *DOCUMENTATION*

arch/arc/kernel/signal.c

@@ -67,7 +67,7 @@ stash_usr_regs(struct rt_sigframe __user *sf, struct pt_regs *regs,
 	       sigset_t *set)
 {
 	int err;
-	err = __copy_to_user(&(sf->uc.uc_mcontext.regs), regs,
+	err = __copy_to_user(&(sf->uc.uc_mcontext.regs.scratch), regs,
 			     sizeof(sf->uc.uc_mcontext.regs.scratch));
 	err |= __copy_to_user(&sf->uc.uc_sigmask, set, sizeof(sigset_t));
 
@@ -83,7 +83,7 @@ static int restore_usr_regs(struct pt_regs *regs, struct rt_sigframe __user *sf)
 	if (!err)
 		set_current_blocked(&set);
 
-	err |= __copy_from_user(regs, &(sf->uc.uc_mcontext.regs),
+	err |= __copy_from_user(regs, &(sf->uc.uc_mcontext.regs.scratch),
 				sizeof(sf->uc.uc_mcontext.regs.scratch));
 
 	return err;
@@ -131,6 +131,15 @@ SYSCALL_DEFINE0(rt_sigreturn)
 	/* Don't restart from sigreturn */
 	syscall_wont_restart(regs);
 
+	/*
+	 * Ensure that sigreturn always returns to user mode (in case the
+	 * regs saved on user stack got fudged between save and sigreturn)
+	 * Otherwise it is easy to panic the kernel with a custom
+	 * signal handler and/or restorer which clobberes the status32/ret
+	 * to return to a bogus location in kernel mode.
+	 */
+	regs->status32 |= STATUS_U_MASK;
+
 	return regs->r0;
 
 badframe:
@@ -229,8 +238,11 @@ setup_rt_frame(struct ksignal *ksig, sigset_t *set, struct pt_regs *regs)
 
 	/*
 	 * handler returns using sigreturn stub provided already by userpsace
+	 * If not, nuke the process right away
 	 */
-	BUG_ON(!(ksig->ka.sa.sa_flags & SA_RESTORER));
+	if(!(ksig->ka.sa.sa_flags & SA_RESTORER))
+		return 1;
+
 	regs->blink = (unsigned long)ksig->ka.sa.sa_restorer;
 
 	/* User Stack for signal handler will be above the frame just carved */
@@ -296,12 +308,12 @@ static void
 handle_signal(struct ksignal *ksig, struct pt_regs *regs)
 {
 	sigset_t *oldset = sigmask_to_save();
-	int ret;
+	int failed;
 
 	/* Set up the stack frame */
-	ret = setup_rt_frame(ksig, oldset, regs);
+	failed = setup_rt_frame(ksig, oldset, regs);
 
-	signal_setup_done(ret, ksig, 0);
+	signal_setup_done(failed, ksig, 0);
 }
 
 void do_signal(struct pt_regs *regs)

arch/arm/Kconfig

@@ -619,6 +619,7 @@ config ARCH_PXA
 	select GENERIC_CLOCKEVENTS
 	select GPIO_PXA
 	select HAVE_IDE
+	select IRQ_DOMAIN
 	select MULTI_IRQ_HANDLER
 	select PLAT_PXA
 	select SPARSE_IRQ

arch/arm/Makefile

@@ -150,6 +150,7 @@ machine-$(CONFIG_ARCH_BERLIN)		+= berlin
 machine-$(CONFIG_ARCH_CLPS711X)		+= clps711x
 machine-$(CONFIG_ARCH_CNS3XXX)		+= cns3xxx
 machine-$(CONFIG_ARCH_DAVINCI)		+= davinci
+machine-$(CONFIG_ARCH_DIGICOLOR)	+= digicolor
 machine-$(CONFIG_ARCH_DOVE)		+= dove
 machine-$(CONFIG_ARCH_EBSA110)		+= ebsa110
 machine-$(CONFIG_ARCH_EFM32)		+= efm32

arch/arm/boot/dts/am335x-bone-common.dtsi

@@ -301,3 +301,11 @@
 	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
 	cd-inverted;
 };
+
+&aes {
+	status = "okay";
+};
+
+&sham {
+	status = "okay";
+};

arch/arm/boot/dts/am335x-bone.dts

@@ -24,11 +24,3 @@
 &mmc1 {
 	vmmc-supply = <&ldo3_reg>;
 };
-
-&sham {
-	status = "okay";
-};
-
-&aes {
-	status = "okay";
-};

arch/arm/boot/dts/am335x-lxm.dts

@@ -328,6 +328,10 @@
 	dual_emac_res_vlan = <3>;
 };
 
+&phy_sel {
+	rmii-clock-ext;
+};
+
 &mac {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;

arch/arm/boot/dts/am33xx-clocks.dtsi

@@ -99,7 +99,7 @@
 	ehrpwm0_tbclk: ehrpwm0_tbclk@44e10664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
-		clocks = <&dpll_per_m2_ck>;
+		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <0>;
 		reg = <0x0664>;
 	};
@@ -107,7 +107,7 @@
 	ehrpwm1_tbclk: ehrpwm1_tbclk@44e10664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
-		clocks = <&dpll_per_m2_ck>;
+		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <1>;
 		reg = <0x0664>;
 	};
@@ -115,7 +115,7 @@
 	ehrpwm2_tbclk: ehrpwm2_tbclk@44e10664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
-		clocks = <&dpll_per_m2_ck>;
+		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <2>;
 		reg = <0x0664>;
 	};

arch/arm/boot/dts/am43xx-clocks.dtsi

@@ -107,7 +107,7 @@
 	ehrpwm0_tbclk: ehrpwm0_tbclk {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
-		clocks = <&dpll_per_m2_ck>;
+		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <0>;
 		reg = <0x0664>;
 	};
@@ -115,7 +115,7 @@
 	ehrpwm1_tbclk: ehrpwm1_tbclk {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
-		clocks = <&dpll_per_m2_ck>;
+		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <1>;
 		reg = <0x0664>;
 	};
@@ -123,7 +123,7 @@
 	ehrpwm2_tbclk: ehrpwm2_tbclk {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
-		clocks = <&dpll_per_m2_ck>;
+		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <2>;
 		reg = <0x0664>;
 	};
@@ -131,7 +131,7 @@
 	ehrpwm3_tbclk: ehrpwm3_tbclk {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
-		clocks = <&dpll_per_m2_ck>;
+		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <4>;
 		reg = <0x0664>;
 	};
@@ -139,7 +139,7 @@
 	ehrpwm4_tbclk: ehrpwm4_tbclk {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
-		clocks = <&dpll_per_m2_ck>;
+		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <5>;
 		reg = <0x0664>;
 	};
@@ -147,7 +147,7 @@
 	ehrpwm5_tbclk: ehrpwm5_tbclk {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
-		clocks = <&dpll_per_m2_ck>;
+		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <6>;
 		reg = <0x0664>;
 	};

arch/arm/boot/dts/at91sam9260.dtsi

@@ -494,12 +494,12 @@
 
 					pinctrl_usart3_rts: usart3_rts-0 {
 						atmel,pins =
-							<AT91_PIOB 8 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PC8 periph B */
+							<AT91_PIOC 8 AT91_PERIPH_B AT91_PINCTRL_NONE>;
 					};
 
 					pinctrl_usart3_cts: usart3_cts-0 {
 						atmel,pins =
-							<AT91_PIOB 10 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PC10 periph B */
+							<AT91_PIOC 10 AT91_PERIPH_B AT91_PINCTRL_NONE>;
 					};
 				};
 
@@ -853,7 +853,7 @@
 			};
 
 			usb1: gadget@fffa4000 {
-				compatible = "atmel,at91rm9200-udc";
+				compatible = "atmel,at91sam9260-udc";
 				reg = <0xfffa4000 0x4000>;
 				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>;
 				clocks = <&udc_clk>, <&udpck>;
@@ -976,7 +976,6 @@
 				atmel,watchdog-type = "hardware";
 				atmel,reset-type = "all";
 				atmel,dbg-halt;
-				atmel,idle-halt;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/at91sam9261.dtsi

@@ -124,11 +124,12 @@
 			};
 
 			usb1: gadget@fffa4000 {
-				compatible = "atmel,at91rm9200-udc";
+				compatible = "atmel,at91sam9261-udc";
 				reg = <0xfffa4000 0x4000>;
 				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 2>;
-				clocks = <&usb>, <&udc_clk>, <&udpck>;
-				clock-names = "usb_clk", "udc_clk", "udpck";
+				clocks = <&udc_clk>, <&udpck>;
+				clock-names = "pclk", "hclk";
+				atmel,matrix = <&matrix>;
 				status = "disabled";
 			};
 
@@ -262,7 +263,7 @@
 			};
 
 			matrix: matrix@ffffee00 {
-				compatible = "atmel,at91sam9260-bus-matrix";
+				compatible = "atmel,at91sam9260-bus-matrix", "syscon";
 				reg = <0xffffee00 0x200>;
 			};
 

arch/arm/boot/dts/at91sam9263.dtsi

@@ -69,7 +69,7 @@
 
 	sram1: sram@00500000 {
 		compatible = "mmio-sram";
-		reg = <0x00300000 0x4000>;
+		reg = <0x00500000 0x4000>;
 	};
 
 	ahb {
@@ -856,7 +856,7 @@
 			};
 
 			usb1: gadget@fff78000 {
-				compatible = "atmel,at91rm9200-udc";
+				compatible = "atmel,at91sam9263-udc";
 				reg = <0xfff78000 0x4000>;
 				interrupts = <24 IRQ_TYPE_LEVEL_HIGH 2>;
 				clocks = <&udc_clk>, <&udpck>;
@@ -905,7 +905,6 @@
 				atmel,watchdog-type = "hardware";
 				atmel,reset-type = "all";
 				atmel,dbg-halt;
-				atmel,idle-halt;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/at91sam9g45.dtsi

@@ -1116,7 +1116,6 @@
 				atmel,watchdog-type = "hardware";
 				atmel,reset-type = "all";
 				atmel,dbg-halt;
-				atmel,idle-halt;
 				status = "disabled";
 			};
 
@@ -1301,7 +1300,7 @@
 			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 			reg = <0x00800000 0x100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&usb>, <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
+			clocks = <&utmi>, <&uhphs_clk>, <&uhphs_clk>, <&uhpck>;
 			clock-names = "usb_clk", "ehci_clk", "hclk", "uhpck";
 			status = "disabled";
 		};

arch/arm/boot/dts/at91sam9n12.dtsi

@@ -894,7 +894,6 @@
 				atmel,watchdog-type = "hardware";
 				atmel,reset-type = "all";
 				atmel,dbg-halt;
-				atmel,idle-halt;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -1066,7 +1066,7 @@
 				reg = <0x00500000 0x80000
 				       0xf803c000 0x400>;
 				interrupts = <23 IRQ_TYPE_LEVEL_HIGH 0>;
-				clocks = <&usb>, <&udphs_clk>;
+				clocks = <&utmi>, <&udphs_clk>;
 				clock-names = "hclk", "pclk";
 				status = "disabled";
 
@@ -1130,7 +1130,6 @@
 				atmel,watchdog-type = "hardware";
 				atmel,reset-type = "all";
 				atmel,dbg-halt;
-				atmel,idle-halt;
 				status = "disabled";
 			};
 
@@ -1186,7 +1185,7 @@
 			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 			reg = <0x00700000 0x100000>;
 			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&usb>, <&uhphs_clk>, <&uhpck>;
+			clocks = <&utmi>, <&uhphs_clk>, <&uhpck>;
 			clock-names = "usb_clk", "ehci_clk", "uhpck";
 			status = "disabled";
 		};

arch/arm/boot/dts/dm8168-evm.dts

@@ -36,6 +36,20 @@
 		>;
 	};
 
+	mmc_pins: pinmux_mmc_pins {
+		pinctrl-single,pins = <
+			DM816X_IOPAD(0x0a70, MUX_MODE0)			/* SD_POW */
+			DM816X_IOPAD(0x0a74, MUX_MODE0)			/* SD_CLK */
+			DM816X_IOPAD(0x0a78, MUX_MODE0)			/* SD_CMD */
+			DM816X_IOPAD(0x0a7C, MUX_MODE0)			/* SD_DAT0 */
+			DM816X_IOPAD(0x0a80, MUX_MODE0)			/* SD_DAT1 */
+			DM816X_IOPAD(0x0a84, MUX_MODE0)			/* SD_DAT2 */
+			DM816X_IOPAD(0x0a88, MUX_MODE0)			/* SD_DAT2 */
+			DM816X_IOPAD(0x0a8c, MUX_MODE2)			/* GP1[7] */
+			DM816X_IOPAD(0x0a90, MUX_MODE2)			/* GP1[8] */
+		>;
+	};
+
 	usb0_pins: pinmux_usb0_pins {
 		pinctrl-single,pins = <
 			DM816X_IOPAD(0x0d00, MUX_MODE0)			/* USB0_DRVVBUS */
@@ -137,7 +151,12 @@
 };
 
 &mmc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc_pins>;
 	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
 };
 
 /* At least dm8168-evm rev c won't support multipoint, later may */

arch/arm/boot/dts/dm816x.dtsi

@@ -150,17 +150,27 @@
 		};
 
 		gpio1: gpio@48032000 {
-			compatible = "ti,omap3-gpio";
+			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio1";
+			ti,gpio-always-on;
 			reg = <0x48032000 0x1000>;
-			interrupts = <97>;
+			interrupts = <96>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		gpio2: gpio@4804c000 {
-			compatible = "ti,omap3-gpio";
+			compatible = "ti,omap4-gpio";
 			ti,hwmods = "gpio2";
+			ti,gpio-always-on;
 			reg = <0x4804c000 0x1000>;
-			interrupts = <99>;
+			interrupts = <98>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		gpmc: gpmc@50000000 {

arch/arm/boot/dts/dra7-evm.dts

@@ -263,17 +263,15 @@
 
 	dcan1_pins_default: dcan1_pins_default {
 		pinctrl-single,pins = <
-			0x3d0   (PIN_OUTPUT | MUX_MODE0) /* dcan1_tx */
-			0x3d4   (MUX_MODE15)		/* dcan1_rx.off */
-			0x418   (PULL_DIS | MUX_MODE1) /* wakeup0.dcan1_rx */
+			0x3d0   (PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
+			0x418   (PULL_UP | MUX_MODE1) /* wakeup0.dcan1_rx */
 		>;
 	};
 
 	dcan1_pins_sleep: dcan1_pins_sleep {
 		pinctrl-single,pins = <
-			0x3d0   (MUX_MODE15)	/* dcan1_tx.off */
-			0x3d4   (MUX_MODE15)	/* dcan1_rx.off */
-			0x418   (MUX_MODE15)	/* wakeup0.off */
+			0x3d0   (MUX_MODE15 | PULL_UP)	/* dcan1_tx.off */
+			0x418   (MUX_MODE15 | PULL_UP)	/* wakeup0.off */
 		>;
 	};
 };

arch/arm/boot/dts/dra7.dtsi

@@ -1111,7 +1111,6 @@
 					      "wkupclk", "refclk",
 					      "div-clk", "phy-div";
 				#phy-cells = <0>;
-				ti,hwmods = "pcie1-phy";
 			};
 
 			pcie2_phy: pciephy@4a095000 {
@@ -1130,7 +1129,6 @@
 					      "wkupclk", "refclk",
 					      "div-clk", "phy-div";
 				#phy-cells = <0>;
-				ti,hwmods = "pcie2-phy";
 				status = "disabled";
 			};
 		};

arch/arm/boot/dts/dra72-evm.dts

@@ -119,17 +119,15 @@
 
 	dcan1_pins_default: dcan1_pins_default {
 		pinctrl-single,pins = <
-			0x3d0   (PIN_OUTPUT | MUX_MODE0) /* dcan1_tx */
-			0x3d4   (MUX_MODE15)		/* dcan1_rx.off */
-			0x418   (PULL_DIS | MUX_MODE1) /* wakeup0.dcan1_rx */
+			0x3d0   (PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
+			0x418   (PULL_UP | MUX_MODE1)	/* wakeup0.dcan1_rx */
 		>;
 	};
 
 	dcan1_pins_sleep: dcan1_pins_sleep {
 		pinctrl-single,pins = <
-			0x3d0   (MUX_MODE15)	/* dcan1_tx.off */
-			0x3d4   (MUX_MODE15)	/* dcan1_rx.off */
-			0x418   (MUX_MODE15)	/* wakeup0.off */
+			0x3d0   (MUX_MODE15 | PULL_UP)	/* dcan1_tx.off */
+			0x418   (MUX_MODE15 | PULL_UP)	/* wakeup0.off */
 		>;
 	};
 

arch/arm/boot/dts/dra7xx-clocks.dtsi

@@ -243,10 +243,18 @@
 		ti,invert-autoidle-bit;
 	};
 
+	dpll_core_byp_mux: dpll_core_byp_mux {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+		ti,bit-shift = <23>;
+		reg = <0x012c>;
+	};
+
 	dpll_core_ck: dpll_core_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-core-clock";
-		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+		clocks = <&sys_clkin1>, <&dpll_core_byp_mux>;
 		reg = <0x0120>, <0x0124>, <0x012c>, <0x0128>;
 	};
 
@@ -309,10 +317,18 @@
 		clock-div = <1>;
 	};
 
+	dpll_dsp_byp_mux: dpll_dsp_byp_mux {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin1>, <&dsp_dpll_hs_clk_div>;
+		ti,bit-shift = <23>;
+		reg = <0x0240>;
+	};
+
 	dpll_dsp_ck: dpll_dsp_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
-		clocks = <&sys_clkin1>, <&dsp_dpll_hs_clk_div>;
+		clocks = <&sys_clkin1>, <&dpll_dsp_byp_mux>;
 		reg = <0x0234>, <0x0238>, <0x0240>, <0x023c>;
 	};
 
@@ -335,10 +351,18 @@
 		clock-div = <1>;
 	};
 
+	dpll_iva_byp_mux: dpll_iva_byp_mux {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin1>, <&iva_dpll_hs_clk_div>;
+		ti,bit-shift = <23>;
+		reg = <0x01ac>;
+	};
+
 	dpll_iva_ck: dpll_iva_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
-		clocks = <&sys_clkin1>, <&iva_dpll_hs_clk_div>;
+		clocks = <&sys_clkin1>, <&dpll_iva_byp_mux>;
 		reg = <0x01a0>, <0x01a4>, <0x01ac>, <0x01a8>;
 	};
 
@@ -361,10 +385,18 @@
 		clock-div = <1>;
 	};
 
+	dpll_gpu_byp_mux: dpll_gpu_byp_mux {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+		ti,bit-shift = <23>;
+		reg = <0x02e4>;
+	};
+
 	dpll_gpu_ck: dpll_gpu_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
-		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+		clocks = <&sys_clkin1>, <&dpll_gpu_byp_mux>;
 		reg = <0x02d8>, <0x02dc>, <0x02e4>, <0x02e0>;
 	};
 
@@ -398,10 +430,18 @@
 		clock-div = <1>;
 	};
 
+	dpll_ddr_byp_mux: dpll_ddr_byp_mux {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+		ti,bit-shift = <23>;
+		reg = <0x021c>;
+	};
+
 	dpll_ddr_ck: dpll_ddr_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
-		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+		clocks = <&sys_clkin1>, <&dpll_ddr_byp_mux>;
 		reg = <0x0210>, <0x0214>, <0x021c>, <0x0218>;
 	};
 
@@ -416,10 +456,18 @@
 		ti,invert-autoidle-bit;
 	};
 
+	dpll_gmac_byp_mux: dpll_gmac_byp_mux {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+		ti,bit-shift = <23>;
+		reg = <0x02b4>;
+	};
+
 	dpll_gmac_ck: dpll_gmac_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
-		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
+		clocks = <&sys_clkin1>, <&dpll_gmac_byp_mux>;
 		reg = <0x02a8>, <0x02ac>, <0x02b4>, <0x02b0>;
 	};
 
@@ -482,10 +530,18 @@
 		clock-div = <1>;
 	};
 
+	dpll_eve_byp_mux: dpll_eve_byp_mux {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin1>, <&eve_dpll_hs_clk_div>;
+		ti,bit-shift = <23>;
+		reg = <0x0290>;
+	};
+
 	dpll_eve_ck: dpll_eve_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
-		clocks = <&sys_clkin1>, <&eve_dpll_hs_clk_div>;
+		clocks = <&sys_clkin1>, <&dpll_eve_byp_mux>;
 		reg = <0x0284>, <0x0288>, <0x0290>, <0x028c>;
 	};
 
@@ -1249,10 +1305,18 @@
 		clock-div = <1>;
 	};
 
+	dpll_per_byp_mux: dpll_per_byp_mux {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin1>, <&per_dpll_hs_clk_div>;
+		ti,bit-shift = <23>;
+		reg = <0x014c>;
+	};
+
 	dpll_per_ck: dpll_per_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
-		clocks = <&sys_clkin1>, <&per_dpll_hs_clk_div>;
+		clocks = <&sys_clkin1>, <&dpll_per_byp_mux>;
 		reg = <0x0140>, <0x0144>, <0x014c>, <0x0148>;
 	};
 
@@ -1275,10 +1339,18 @@
 		clock-div = <1>;
 	};
 
+	dpll_usb_byp_mux: dpll_usb_byp_mux {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin1>, <&usb_dpll_hs_clk_div>;
+		ti,bit-shift = <23>;
+		reg = <0x018c>;
+	};
+
 	dpll_usb_ck: dpll_usb_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-j-type-clock";
-		clocks = <&sys_clkin1>, <&usb_dpll_hs_clk_div>;
+		clocks = <&sys_clkin1>, <&dpll_usb_byp_mux>;
 		reg = <0x0180>, <0x0184>, <0x018c>, <0x0188>;
 	};
 

arch/arm/boot/dts/exynos3250.dtsi

@@ -18,6 +18,7 @@
  */
 
 #include "skeleton.dtsi"
+#include "exynos4-cpu-thermal.dtsi"
 #include <dt-bindings/clock/exynos3250.h>
 
 / {
@@ -193,6 +194,7 @@
 			interrupts = <0 216 0>;
 			clocks = <&cmu CLK_TMU_APBIF>;
 			clock-names = "tmu_apbif";
+			#include "exynos4412-tmu-sensor-conf.dtsi"
 			status = "disabled";
 		};
 

arch/arm/boot/dts/exynos4-cpu-thermal.dtsi

@@ -0,0 +1,52 @@
+/*
+ * Device tree sources for Exynos4 thermal zone
+ *
+ * Copyright (c) 2014 Lukasz Majewski <l.majewski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+thermal-zones {
+	cpu_thermal: cpu-thermal {
+		thermal-sensors = <&tmu 0>;
+		polling-delay-passive = <0>;
+		polling-delay = <0>;
+		trips {
+			cpu_alert0: cpu-alert-0 {
+				temperature = <70000>; /* millicelsius */
+				hysteresis = <10000>; /* millicelsius */
+				type = "active";
+			};
+			cpu_alert1: cpu-alert-1 {
+				temperature = <95000>; /* millicelsius */
+				hysteresis = <10000>; /* millicelsius */
+				type = "active";
+			};
+			cpu_alert2: cpu-alert-2 {
+				temperature = <110000>; /* millicelsius */
+				hysteresis = <10000>; /* millicelsius */
+				type = "active";
+			};
+			cpu_crit0: cpu-crit-0 {
+				temperature = <120000>; /* millicelsius */
+				hysteresis = <0>; /* millicelsius */
+				type = "critical";
+			};
+		};
+		cooling-maps {
+			map0 {
+				trip = <&cpu_alert0>;
+			};
+			map1 {
+				trip = <&cpu_alert1>;
+			};
+		};
+	};
+};
+};

arch/arm/boot/dts/exynos4.dtsi

@@ -38,6 +38,7 @@
 		i2c5 = &i2c_5;
 		i2c6 = &i2c_6;
 		i2c7 = &i2c_7;
+		i2c8 = &i2c_8;
 		csis0 = &csis_0;
 		csis1 = &csis_1;
 		fimc0 = &fimc_0;
@@ -104,6 +105,7 @@
 		compatible = "samsung,exynos4210-pd";
 		reg = <0x10023C20 0x20>;
 		#power-domain-cells = <0>;
+		power-domains = <&pd_lcd0>;
 	};
 
 	pd_cam: cam-power-domain@10023C00 {
@@ -554,6 +556,22 @@
 		status = "disabled";
 	};
 
+	i2c_8: i2c@138E0000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "samsung,s3c2440-hdmiphy-i2c";
+		reg = <0x138E0000 0x100>;
+		interrupts = <0 93 0>;
+		clocks = <&clock CLK_I2C_HDMI>;
+		clock-names = "i2c";
+		status = "disabled";
+
+		hdmi_i2c_phy: hdmiphy@38 {
+			compatible = "exynos4210-hdmiphy";
+			reg = <0x38>;
+		};
+	};
+
 	spi_0: spi@13920000 {
 		compatible = "samsung,exynos4210-spi";
 		reg = <0x13920000 0x100>;
@@ -663,6 +681,33 @@
 		status = "disabled";
 	};
 
+	tmu: tmu@100C0000 {
+		#include "exynos4412-tmu-sensor-conf.dtsi"
+	};
+
+	hdmi: hdmi@12D00000 {
+		compatible = "samsung,exynos4210-hdmi";
+		reg = <0x12D00000 0x70000>;
+		interrupts = <0 92 0>;
+		clock-names = "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy",
+			"mout_hdmi";
+		clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>,
+			<&clock CLK_SCLK_PIXEL>, <&clock CLK_SCLK_HDMIPHY>,
+			<&clock CLK_MOUT_HDMI>;
+		phy = <&hdmi_i2c_phy>;
+		power-domains = <&pd_tv>;
+		samsung,syscon-phandle = <&pmu_system_controller>;
+		status = "disabled";
+	};
+
+	mixer: mixer@12C10000 {
+		compatible = "samsung,exynos4210-mixer";
+		interrupts = <0 91 0>;
+		reg = <0x12C10000 0x2100>, <0x12c00000 0x300>;
+		power-domains = <&pd_tv>;
+		status = "disabled";
+	};
+
 	ppmu_dmc0: ppmu_dmc0@106a0000 {
 		compatible = "samsung,exynos-ppmu";
 		reg = <0x106a0000 0x2000>;

arch/arm/boot/dts/exynos4210-trats.dts

@@ -426,6 +426,25 @@
 		status = "okay";
 	};
 
+	tmu@100C0000 {
+		status = "okay";
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			cooling-maps {
+				map0 {
+				     /* Corresponds to 800MHz at freq_table */
+				     cooling-device = <&cpu0 2 2>;
+				};
+				map1 {
+				     /* Corresponds to 200MHz at freq_table */
+				     cooling-device = <&cpu0 4 4>;
+			       };
+		       };
+		};
+	};
+
 	camera {
 		pinctrl-names = "default";
 		pinctrl-0 = <>;

arch/arm/boot/dts/exynos4210-universal_c210.dts

@@ -505,6 +505,63 @@
 			assigned-clock-rates = <0>, <160000000>;
 		};
 	};
+
+	hdmi_en: voltage-regulator-hdmi-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "HDMI_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpe0 1 0>;
+		enable-active-high;
+	};
+
+	hdmi_ddc: i2c-ddc {
+		compatible = "i2c-gpio";
+		gpios = <&gpe4 2 0 &gpe4 3 0>;
+		i2c-gpio,delay-us = <100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-0 = <&i2c_ddc_bus>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+
+	mixer@12C10000 {
+		status = "okay";
+	};
+
+	hdmi@12D00000 {
+		hpd-gpio = <&gpx3 7 0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&hdmi_hpd>;
+		hdmi-en-supply = <&hdmi_en>;
+		vdd-supply = <&ldo3_reg>;
+		vdd_osc-supply = <&ldo4_reg>;
+		vdd_pll-supply = <&ldo3_reg>;
+		ddc = <&hdmi_ddc>;
+		status = "okay";
+	};
+
+	i2c@138E0000 {
+		status = "okay";
+	};
+};
+
+&pinctrl_1 {
+	hdmi_hpd: hdmi-hpd {
+		samsung,pins = "gpx3-7";
+		samsung,pin-pud = <0>;
+	};
+};
+
+&pinctrl_0 {
+	i2c_ddc_bus: i2c-ddc-bus {
+		samsung,pins = "gpe4-2", "gpe4-3";
+		samsung,pin-function = <2>;
+		samsung,pin-pud = <3>;
+		samsung,pin-drv = <0>;
+	};
 };
 
 &mdma1 {

arch/arm/boot/dts/exynos4210.dtsi

@@ -21,6 +21,7 @@
 
 #include "exynos4.dtsi"
 #include "exynos4210-pinctrl.dtsi"
+#include "exynos4-cpu-thermal.dtsi"
 
 / {
 	compatible = "samsung,exynos4210", "samsung,exynos4";
@@ -35,10 +36,13 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@900 {
+		cpu0: cpu@900 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <0x900>;
+			cooling-min-level = <4>;
+			cooling-max-level = <2>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 
 		cpu@901 {
@@ -153,16 +157,38 @@
 		reg = <0x03860000 0x1000>;
 	};
 
-	tmu@100C0000 {
+	tmu: tmu@100C0000 {
 		compatible = "samsung,exynos4210-tmu";
 		interrupt-parent = <&combiner>;
 		reg = <0x100C0000 0x100>;
 		interrupts = <2 4>;
 		clocks = <&clock CLK_TMU_APBIF>;
 		clock-names = "tmu_apbif";
+		samsung,tmu_gain = <15>;
+		samsung,tmu_reference_voltage = <7>;
 		status = "disabled";
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tmu 0>;
+
+			trips {
+			      cpu_alert0: cpu-alert-0 {
+				      temperature = <85000>; /* millicelsius */
+			      };
+			      cpu_alert1: cpu-alert-1 {
+				      temperature = <100000>; /* millicelsius */
+			      };
+			      cpu_alert2: cpu-alert-2 {
+				      temperature = <110000>; /* millicelsius */
+			      };
+			};
+		};
+	};
+
 	g2d@12800000 {
 		compatible = "samsung,s5pv210-g2d";
 		reg = <0x12800000 0x1000>;
@@ -203,6 +229,14 @@
 		};
 	};
 
+	mixer: mixer@12C10000 {
+		clock-names = "mixer", "hdmi", "sclk_hdmi", "vp", "mout_mixer",
+			"sclk_mixer";
+		clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
+			<&clock CLK_SCLK_HDMI>, <&clock CLK_VP>,
+			<&clock CLK_MOUT_MIXER>, <&clock CLK_SCLK_MIXER>;
+	};
+
 	ppmu_lcd1: ppmu_lcd1@12240000 {
 		compatible = "samsung,exynos-ppmu";
 		reg = <0x12240000 0x2000>;

arch/arm/boot/dts/exynos4212.dtsi

@@ -26,10 +26,13 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@A00 {
+		cpu0: cpu@A00 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <0xA00>;
+			cooling-min-level = <13>;
+			cooling-max-level = <7>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 
 		cpu@A01 {

arch/arm/boot/dts/exynos4412-odroid-common.dtsi

@@ -249,6 +249,20 @@
 					regulator-always-on;
 				};
 
+				ldo8_reg: ldo@8 {
+					regulator-compatible = "LDO8";
+					regulator-name = "VDD10_HDMI_1.0V";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+				};
+
+				ldo10_reg: ldo@10 {
+					regulator-compatible = "LDO10";
+					regulator-name = "VDDQ_MIPIHSI_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
 				ldo11_reg: LDO11 {
 					regulator-name = "VDD18_ABB1_1.8V";
 					regulator-min-microvolt = <1800000>;
@@ -411,6 +425,51 @@
 	ehci: ehci@12580000 {
 		status = "okay";
 	};
+
+	tmu@100C0000 {
+		vtmu-supply = <&ldo10_reg>;
+		status = "okay";
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			cooling-maps {
+				map0 {
+				     /* Corresponds to 800MHz at freq_table */
+				     cooling-device = <&cpu0 7 7>;
+				};
+				map1 {
+				     /* Corresponds to 200MHz at freq_table */
+				     cooling-device = <&cpu0 13 13>;
+			       };
+		       };
+		};
+	};
+
+	mixer: mixer@12C10000 {
+		status = "okay";
+	};
+
+	hdmi@12D00000 {
+		hpd-gpio = <&gpx3 7 0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&hdmi_hpd>;
+		vdd-supply = <&ldo8_reg>;
+		vdd_osc-supply = <&ldo10_reg>;
+		vdd_pll-supply = <&ldo8_reg>;
+		ddc = <&hdmi_ddc>;
+		status = "okay";
+	};
+
+	hdmi_ddc: i2c@13880000 {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c2_bus>;
+	};
+
+	i2c@138E0000 {
+		status = "okay";
+	};
 };
 
 &pinctrl_1 {
@@ -425,4 +484,9 @@
 		samsung,pin-pud = <0>;
 		samsung,pin-drv = <0>;
 	};
+
+	hdmi_hpd: hdmi-hpd {
+		samsung,pins = "gpx3-7";
+		samsung,pin-pud = <1>;
+	};
 };

arch/arm/boot/dts/exynos4412-tmu-sensor-conf.dtsi

@@ -0,0 +1,24 @@
+/*
+ * Device tree sources for Exynos4412 TMU sensor configuration
+ *
+ * Copyright (c) 2014 Lukasz Majewski <l.majewski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <dt-bindings/thermal/thermal_exynos.h>
+
+#thermal-sensor-cells = <0>;
+samsung,tmu_gain = <8>;
+samsung,tmu_reference_voltage = <16>;
+samsung,tmu_noise_cancel_mode = <4>;
+samsung,tmu_efuse_value = <55>;
+samsung,tmu_min_efuse_value = <40>;
+samsung,tmu_max_efuse_value = <100>;
+samsung,tmu_first_point_trim = <25>;
+samsung,tmu_second_point_trim = <85>;
+samsung,tmu_default_temp_offset = <50>;
+samsung,tmu_cal_type = <TYPE_ONE_POINT_TRIMMING>;

arch/arm/boot/dts/exynos4412-trats2.dts

@@ -927,6 +927,21 @@
 		pulldown-ohm = <100000>; /* 100K */
 		io-channels = <&adc 2>;  /* Battery temperature */
 	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			cooling-maps {
+				map0 {
+				     /* Corresponds to 800MHz at freq_table */
+				     cooling-device = <&cpu0 7 7>;
+				};
+				map1 {
+				     /* Corresponds to 200MHz at freq_table */
+				     cooling-device = <&cpu0 13 13>;
+			       };
+		       };
+		};
+	};
 };
 
 &pmu_system_controller {

arch/arm/boot/dts/exynos4412.dtsi

@@ -26,10 +26,13 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@A00 {
+		cpu0: cpu@A00 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a9";
 			reg = <0xA00>;
+			cooling-min-level = <13>;
+			cooling-max-level = <7>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 
 		cpu@A01 {

arch/arm/boot/dts/exynos4x12.dtsi

@@ -19,6 +19,7 @@
 
 #include "exynos4.dtsi"
 #include "exynos4x12-pinctrl.dtsi"
+#include "exynos4-cpu-thermal.dtsi"
 
 / {
 	aliases {
@@ -297,4 +298,15 @@
 		clock-names = "tmu_apbif";
 		status = "disabled";
 	};
+
+	hdmi: hdmi@12D00000 {
+		compatible = "samsung,exynos4212-hdmi";
+	};
+
+	mixer: mixer@12C10000 {
+		compatible = "samsung,exynos4212-mixer";
+		clock-names = "mixer", "hdmi", "sclk_hdmi", "vp";
+		clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
+			 <&clock CLK_SCLK_HDMI>, <&clock CLK_VP>;
+	};
 };

arch/arm/boot/dts/exynos5250.dtsi

@@ -20,7 +20,7 @@
 #include <dt-bindings/clock/exynos5250.h>
 #include "exynos5.dtsi"
 #include "exynos5250-pinctrl.dtsi"
-
+#include "exynos4-cpu-thermal.dtsi"
 #include <dt-bindings/clock/exynos-audss-clk.h>
 
 / {
@@ -58,11 +58,14 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0>;
 			clock-frequency = <1700000000>;
+			cooling-min-level = <15>;
+			cooling-max-level = <9>;
+			#cooling-cells = <2>; /* min followed by max */
 		};
 		cpu@1 {
 			device_type = "cpu";
@@ -102,6 +105,12 @@
 		#power-domain-cells = <0>;
 	};
 
+	pd_disp1: disp1-power-domain@100440A0 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x100440A0 0x20>;
+		#power-domain-cells = <0>;
+	};
+
 	clock: clock-controller@10010000 {
 		compatible = "samsung,exynos5250-clock";
 		reg = <0x10010000 0x30000>;
@@ -235,12 +244,32 @@
 		status = "disabled";
 	};
 
-	tmu@10060000 {
+	tmu: tmu@10060000 {
 		compatible = "samsung,exynos5250-tmu";
 		reg = <0x10060000 0x100>;
 		interrupts = <0 65 0>;
 		clocks = <&clock CLK_TMU>;
 		clock-names = "tmu_apbif";
+		#include "exynos4412-tmu-sensor-conf.dtsi"
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tmu 0>;
+
+			cooling-maps {
+				map0 {
+				     /* Corresponds to 800MHz at freq_table */
+				     cooling-device = <&cpu0 9 9>;
+				};
+				map1 {
+				     /* Corresponds to 200MHz at freq_table */
+				     cooling-device = <&cpu0 15 15>;
+			       };
+		       };
+		};
 	};
 
 	serial@12C00000 {
@@ -719,6 +748,7 @@
 	hdmi: hdmi {
 		compatible = "samsung,exynos4212-hdmi";
 		reg = <0x14530000 0x70000>;
+		power-domains = <&pd_disp1>;
 		interrupts = <0 95 0>;
 		clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>,
 			 <&clock CLK_SCLK_PIXEL>, <&clock CLK_SCLK_HDMIPHY>,
@@ -731,9 +761,11 @@
 	mixer {
 		compatible = "samsung,exynos5250-mixer";
 		reg = <0x14450000 0x10000>;
+		power-domains = <&pd_disp1>;
 		interrupts = <0 94 0>;
-		clocks = <&clock CLK_MIXER>, <&clock CLK_SCLK_HDMI>;
-		clock-names = "mixer", "sclk_hdmi";
+		clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
+			 <&clock CLK_SCLK_HDMI>;
+		clock-names = "mixer", "hdmi", "sclk_hdmi";
 	};
 
 	dp_phy: video-phy@10040720 {
@@ -743,6 +775,7 @@
 	};
 
 	dp: dp-controller@145B0000 {
+		power-domains = <&pd_disp1>;
 		clocks = <&clock CLK_DP>;
 		clock-names = "dp";
 		phys = <&dp_phy>;
@@ -750,6 +783,7 @@
 	};
 
 	fimd: fimd@14400000 {
+		power-domains = <&pd_disp1>;
 		clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>;
 		clock-names = "sclk_fimd", "fimd";
 	};

arch/arm/boot/dts/exynos5420-trip-points.dtsi

@@ -0,0 +1,35 @@
+/*
+ * Device tree sources for default Exynos5420 thermal zone definition
+ *
+ * Copyright (c) 2014 Lukasz Majewski <l.majewski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+polling-delay-passive = <0>;
+polling-delay = <0>;
+trips {
+	cpu-alert-0 {
+		temperature = <85000>; /* millicelsius */
+		hysteresis = <10000>; /* millicelsius */
+		type = "active";
+	};
+	cpu-alert-1 {
+		temperature = <103000>; /* millicelsius */
+		hysteresis = <10000>; /* millicelsius */
+		type = "active";
+	};
+	cpu-alert-2 {
+		temperature = <110000>; /* millicelsius */
+		hysteresis = <10000>; /* millicelsius */
+		type = "active";
+	};
+	cpu-crit-0 {
+		temperature = <1200000>; /* millicelsius */
+		hysteresis = <0>; /* millicelsius */
+		type = "critical";
+	};
+};

arch/arm/boot/dts/exynos5420.dtsi

@@ -740,8 +740,9 @@
 		compatible = "samsung,exynos5420-mixer";
 		reg = <0x14450000 0x10000>;
 		interrupts = <0 94 0>;
-		clocks = <&clock CLK_MIXER>, <&clock CLK_SCLK_HDMI>;
-		clock-names = "mixer", "sclk_hdmi";
+		clocks = <&clock CLK_MIXER>, <&clock CLK_HDMI>,
+			 <&clock CLK_SCLK_HDMI>;
+		clock-names = "mixer", "hdmi", "sclk_hdmi";
 		power-domains = <&disp_pd>;
 	};
 
@@ -782,6 +783,7 @@
 		interrupts = <0 65 0>;
 		clocks = <&clock CLK_TMU>;
 		clock-names = "tmu_apbif";
+		#include "exynos4412-tmu-sensor-conf.dtsi"
 	};
 
 	tmu_cpu1: tmu@10064000 {
@@ -790,6 +792,7 @@
 		interrupts = <0 183 0>;
 		clocks = <&clock CLK_TMU>;
 		clock-names = "tmu_apbif";
+		#include "exynos4412-tmu-sensor-conf.dtsi"
 	};
 
 	tmu_cpu2: tmu@10068000 {
@@ -798,6 +801,7 @@
 		interrupts = <0 184 0>;
 		clocks = <&clock CLK_TMU>, <&clock CLK_TMU>;
 		clock-names = "tmu_apbif", "tmu_triminfo_apbif";
+		#include "exynos4412-tmu-sensor-conf.dtsi"
 	};
 
 	tmu_cpu3: tmu@1006c000 {
@@ -806,6 +810,7 @@
 		interrupts = <0 185 0>;
 		clocks = <&clock CLK_TMU>, <&clock CLK_TMU_GPU>;
 		clock-names = "tmu_apbif", "tmu_triminfo_apbif";
+		#include "exynos4412-tmu-sensor-conf.dtsi"
 	};
 
 	tmu_gpu: tmu@100a0000 {
@@ -814,6 +819,30 @@
 		interrupts = <0 215 0>;
 		clocks = <&clock CLK_TMU_GPU>, <&clock CLK_TMU>;
 		clock-names = "tmu_apbif", "tmu_triminfo_apbif";
+		#include "exynos4412-tmu-sensor-conf.dtsi"
+	};
+
+	thermal-zones {
+		cpu0_thermal: cpu0-thermal {
+			thermal-sensors = <&tmu_cpu0>;
+			#include "exynos5420-trip-points.dtsi"
+		};
+		cpu1_thermal: cpu1-thermal {
+		       thermal-sensors = <&tmu_cpu1>;
+		       #include "exynos5420-trip-points.dtsi"
+		};
+		cpu2_thermal: cpu2-thermal {
+		       thermal-sensors = <&tmu_cpu2>;
+		       #include "exynos5420-trip-points.dtsi"
+		};
+		cpu3_thermal: cpu3-thermal {
+		       thermal-sensors = <&tmu_cpu3>;
+		       #include "exynos5420-trip-points.dtsi"
+		};
+		gpu_thermal: gpu-thermal {
+		       thermal-sensors = <&tmu_gpu>;
+		       #include "exynos5420-trip-points.dtsi"
+		};
 	};
 
         watchdog: watchdog@101D0000 {

arch/arm/boot/dts/exynos5440-tmu-sensor-conf.dtsi

@@ -0,0 +1,24 @@
+/*
+ * Device tree sources for Exynos5440 TMU sensor configuration
+ *
+ * Copyright (c) 2014 Lukasz Majewski <l.majewski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <dt-bindings/thermal/thermal_exynos.h>
+
+#thermal-sensor-cells = <0>;
+samsung,tmu_gain = <5>;
+samsung,tmu_reference_voltage = <16>;
+samsung,tmu_noise_cancel_mode = <4>;
+samsung,tmu_efuse_value = <0x5d2d>;
+samsung,tmu_min_efuse_value = <16>;
+samsung,tmu_max_efuse_value = <76>;
+samsung,tmu_first_point_trim = <25>;
+samsung,tmu_second_point_trim = <70>;
+samsung,tmu_default_temp_offset = <25>;
+samsung,tmu_cal_type = <TYPE_ONE_POINT_TRIMMING>;

arch/arm/boot/dts/exynos5440-trip-points.dtsi

@@ -0,0 +1,25 @@
+/*
+ * Device tree sources for default Exynos5440 thermal zone definition
+ *
+ * Copyright (c) 2014 Lukasz Majewski <l.majewski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+polling-delay-passive = <0>;
+polling-delay = <0>;
+trips {
+	cpu-alert-0 {
+		temperature = <100000>; /* millicelsius */
+		hysteresis = <0>; /* millicelsius */
+		type = "active";
+	};
+	cpu-crit-0 {
+		temperature = <1050000>; /* millicelsius */
+		hysteresis = <0>; /* millicelsius */
+		type = "critical";
+	};
+};

arch/arm/boot/dts/exynos5440.dtsi

@@ -219,6 +219,7 @@
 		interrupts = <0 58 0>;
 		clocks = <&clock CLK_B_125>;
 		clock-names = "tmu_apbif";
+		#include "exynos5440-tmu-sensor-conf.dtsi"
 	};
 
 	tmuctrl_1: tmuctrl@16011C {
@@ -227,6 +228,7 @@
 		interrupts = <0 58 0>;
 		clocks = <&clock CLK_B_125>;
 		clock-names = "tmu_apbif";
+		#include "exynos5440-tmu-sensor-conf.dtsi"
 	};
 
 	tmuctrl_2: tmuctrl@160120 {
@@ -235,6 +237,22 @@
 		interrupts = <0 58 0>;
 		clocks = <&clock CLK_B_125>;
 		clock-names = "tmu_apbif";
+		#include "exynos5440-tmu-sensor-conf.dtsi"
+	};
+
+	thermal-zones {
+		cpu0_thermal: cpu0-thermal {
+			thermal-sensors = <&tmuctrl_0>;
+			#include "exynos5440-trip-points.dtsi"
+		};
+		cpu1_thermal: cpu1-thermal {
+		       thermal-sensors = <&tmuctrl_1>;
+		       #include "exynos5440-trip-points.dtsi"
+		};
+		cpu2_thermal: cpu2-thermal {
+		       thermal-sensors = <&tmuctrl_2>;
+		       #include "exynos5440-trip-points.dtsi"
+		};
 	};
 
 	sata@210000 {

arch/arm/boot/dts/imx6qdl-sabresd.dtsi

@@ -35,6 +35,7 @@
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio3 22 0>;
 			enable-active-high;
+			vin-supply = <&swbst_reg>;
 		};
 
 		reg_usb_h1_vbus: regulator@1 {
@@ -45,6 +46,7 @@
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio1 29 0>;
 			enable-active-high;
+			vin-supply = <&swbst_reg>;
 		};
 
 		reg_audio: regulator@2 {

arch/arm/boot/dts/imx6sl-evk.dts

@@ -52,6 +52,7 @@
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio4 0 0>;
 			enable-active-high;
+			vin-supply = <&swbst_reg>;
 		};
 
 		reg_usb_otg2_vbus: regulator@1 {
@@ -62,6 +63,7 @@
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio4 2 0>;
 			enable-active-high;
+			vin-supply = <&swbst_reg>;
 		};
 
 		reg_aud3v: regulator@2 {

arch/arm/boot/dts/omap3.dtsi

@@ -92,6 +92,8 @@
 			ti,hwmods = "aes";
 			reg = <0x480c5000 0x50>;
 			interrupts = <0>;
+			dmas = <&sdma 65 &sdma 66>;
+			dma-names = "tx", "rx";
 		};
 
 		prm: prm@48306000 {
@@ -550,6 +552,8 @@
 			ti,hwmods = "sham";
 			reg = <0x480c3000 0x64>;
 			interrupts = <49>;
+			dmas = <&sdma 69>;
+			dma-names = "rx";
 		};
 
 		smartreflex_core: smartreflex@480cb000 {

arch/arm/boot/dts/omap5-core-thermal.dtsi

@@ -13,7 +13,7 @@
 
 core_thermal: core_thermal {
 	polling-delay-passive = <250>; /* milliseconds */
-	polling-delay = <1000>; /* milliseconds */
+	polling-delay = <500>; /* milliseconds */
 
 			/* sensor       ID */
 	thermal-sensors = <&bandgap     2>;

arch/arm/boot/dts/omap5-gpu-thermal.dtsi

@@ -13,7 +13,7 @@
 
 gpu_thermal: gpu_thermal {
 	polling-delay-passive = <250>; /* milliseconds */
-	polling-delay = <1000>; /* milliseconds */
+	polling-delay = <500>; /* milliseconds */
 
 			/* sensor       ID */
 	thermal-sensors = <&bandgap     1>;

arch/arm/boot/dts/omap5.dtsi

@@ -1079,4 +1079,8 @@
 	};
 };
 
+&cpu_thermal {
+	polling-delay = <500>; /* milliseconds */
+};
+
 /include/ "omap54xx-clocks.dtsi"

arch/arm/boot/dts/omap54xx-clocks.dtsi

@@ -167,10 +167,18 @@
 		ti,index-starts-at-one;
 	};
 
+	dpll_core_byp_mux: dpll_core_byp_mux {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin>, <&dpll_abe_m3x2_ck>;
+		ti,bit-shift = <23>;
+		reg = <0x012c>;
+	};
+
 	dpll_core_ck: dpll_core_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-core-clock";
-		clocks = <&sys_clkin>, <&dpll_abe_m3x2_ck>;
+		clocks = <&sys_clkin>, <&dpll_core_byp_mux>;
 		reg = <0x0120>, <0x0124>, <0x012c>, <0x0128>;
 	};
 
@@ -294,10 +302,18 @@
 		clock-div = <1>;
 	};
 
+	dpll_iva_byp_mux: dpll_iva_byp_mux {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin>, <&iva_dpll_hs_clk_div>;
+		ti,bit-shift = <23>;
+		reg = <0x01ac>;
+	};
+
 	dpll_iva_ck: dpll_iva_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
-		clocks = <&sys_clkin>, <&iva_dpll_hs_clk_div>;
+		clocks = <&sys_clkin>, <&dpll_iva_byp_mux>;
 		reg = <0x01a0>, <0x01a4>, <0x01ac>, <0x01a8>;
 	};
 
@@ -599,10 +615,19 @@
 	};
 };
 &cm_core_clocks {
+
+	dpll_per_byp_mux: dpll_per_byp_mux {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin>, <&per_dpll_hs_clk_div>;
+		ti,bit-shift = <23>;
+		reg = <0x014c>;
+	};
+
 	dpll_per_ck: dpll_per_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
-		clocks = <&sys_clkin>, <&per_dpll_hs_clk_div>;
+		clocks = <&sys_clkin>, <&dpll_per_byp_mux>;
 		reg = <0x0140>, <0x0144>, <0x014c>, <0x0148>;
 	};
 
@@ -714,10 +739,18 @@
 		ti,index-starts-at-one;
 	};
 
+	dpll_usb_byp_mux: dpll_usb_byp_mux {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin>, <&usb_dpll_hs_clk_div>;
+		ti,bit-shift = <23>;
+		reg = <0x018c>;
+	};
+
 	dpll_usb_ck: dpll_usb_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-j-type-clock";
-		clocks = <&sys_clkin>, <&usb_dpll_hs_clk_div>;
+		clocks = <&sys_clkin>, <&dpll_usb_byp_mux>;
 		reg = <0x0180>, <0x0184>, <0x018c>, <0x0188>;
 	};
 

arch/arm/boot/dts/rk3288.dtsi

@@ -411,6 +411,7 @@
 			"mac_clk_rx", "mac_clk_tx",
 			"clk_mac_ref", "clk_mac_refout",
 			"aclk_mac", "pclk_mac";
+		status = "disabled";
 	};
 
 	usb_host0_ehci: usb@ff500000 {

arch/arm/boot/dts/sama5d3.dtsi

@@ -1248,7 +1248,6 @@
 				atmel,watchdog-type = "hardware";
 				atmel,reset-type = "all";
 				atmel,dbg-halt;
-				atmel,idle-halt;
 				status = "disabled";
 			};
 
@@ -1416,7 +1415,7 @@
 			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 			reg = <0x00700000 0x100000>;
 			interrupts = <32 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&usb>, <&uhphs_clk>, <&uhpck>;
+			clocks = <&utmi>, <&uhphs_clk>, <&uhpck>;
 			clock-names = "usb_clk", "ehci_clk", "uhpck";
 			status = "disabled";
 		};

arch/arm/boot/dts/sama5d4.dtsi

@@ -66,6 +66,7 @@
 		gpio4 = &pioE;
 		tcb0 = &tcb0;
 		tcb1 = &tcb1;
+		i2c0 = &i2c0;
 		i2c2 = &i2c2;
 	};
 	cpus {
@@ -259,7 +260,7 @@
 			compatible = "atmel,at91sam9g45-ehci", "usb-ehci";
 			reg = <0x00600000 0x100000>;
 			interrupts = <46 IRQ_TYPE_LEVEL_HIGH 2>;
-			clocks = <&usb>, <&uhphs_clk>, <&uhpck>;
+			clocks = <&utmi>, <&uhphs_clk>, <&uhpck>;
 			clock-names = "usb_clk", "ehci_clk", "uhpck";
 			status = "disabled";
 		};
@@ -461,8 +462,8 @@
 
 					lcdck: lcdck {
 						#clock-cells = <0>;
-						reg = <4>;
-						clocks = <&smd>;
+						reg = <3>;
+						clocks = <&mck>;
 					};
 
 					smdck: smdck {
@@ -770,7 +771,7 @@
 						reg = <50>;
 					};
 
-					lcd_clk: lcd_clk {
+					lcdc_clk: lcdc_clk {
 						#clock-cells = <0>;
 						reg = <51>;
 					};

arch/arm/boot/dts/socfpga.dtsi

@@ -660,7 +660,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0xfff01000 0x1000>;
-			interrupts = <0 156 4>;
+			interrupts = <0 155 4>;
 			num-cs = <4>;
 			clocks = <&spi_m_clk>;
 			status = "disabled";
@@ -713,6 +713,9 @@
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&l4_sp_clk>;
+			dmas = <&pdma 28>,
+			       <&pdma 29>;
+			dma-names = "tx", "rx";
 		};
 
 		uart1: serial1@ffc03000 {
@@ -722,6 +725,9 @@
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clocks = <&l4_sp_clk>;
+			dmas = <&pdma 30>,
+			       <&pdma 31>;
+			dma-names = "tx", "rx";
 		};
 
 		rst: rstmgr@ffd05000 {

arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts

@@ -56,6 +56,22 @@
 	model = "Olimex A10-OLinuXino-LIME";
 	compatible = "olimex,a10-olinuxino-lime", "allwinner,sun4i-a10";
 
+	cpus {
+		cpu0: cpu@0 {
+			/*
+			 * The A10-Lime is known to be unstable
+			 * when running at 1008 MHz
+			 */
+			operating-points = <
+				/* kHz    uV */
+				912000  1350000
+				864000  1300000
+				624000  1250000
+				>;
+			cooling-max-level = <2>;
+		};
+	};
+
 	soc@01c00000 {
 		emac: ethernet@01c0b000 {
 			pinctrl-names = "default";

arch/arm/boot/dts/sun4i-a10.dtsi

@@ -75,7 +75,6 @@
 			clock-latency = <244144>; /* 8 32k periods */
 			operating-points = <
 				/* kHz    uV */
-				1056000 1500000
 				1008000 1400000
 				912000  1350000
 				864000  1300000
@@ -83,7 +82,7 @@
 				>;
 			#cooling-cells = <2>;
 			cooling-min-level = <0>;
-			cooling-max-level = <4>;
+			cooling-max-level = <3>;
 		};
 	};
 

arch/arm/boot/dts/sun5i-a13.dtsi

@@ -47,7 +47,6 @@
 			clock-latency = <244144>; /* 8 32k periods */
 			operating-points = <
 				/* kHz    uV */
-				1104000	1500000
 				1008000 1400000
 				912000  1350000
 				864000  1300000
@@ -57,7 +56,7 @@
 				>;
 			#cooling-cells = <2>;
 			cooling-min-level = <0>;
-			cooling-max-level = <6>;
+			cooling-max-level = <5>;
 		};
 	};
 

arch/arm/boot/dts/sun7i-a20.dtsi

@@ -105,7 +105,6 @@
 			clock-latency = <244144>; /* 8 32k periods */
 			operating-points = <
 				/* kHz    uV */
-				1008000 1450000
 				960000  1400000
 				912000  1400000
 				864000  1300000
@@ -116,7 +115,7 @@
 				>;
 			#cooling-cells = <2>;
 			cooling-min-level = <0>;
-			cooling-max-level = <7>;
+			cooling-max-level = <6>;
 		};
 
 		cpu@1 {

arch/arm/configs/at91_dt_defconfig

@@ -70,6 +70,7 @@ CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
 # CONFIG_SCSI_LOWLEVEL is not set
 CONFIG_NETDEVICES=y
+CONFIG_ARM_AT91_ETHER=y
 CONFIG_MACB=y
 # CONFIG_NET_VENDOR_BROADCOM is not set
 CONFIG_DM9000=y

arch/arm/configs/multi_v7_defconfig

@@ -99,7 +99,7 @@ CONFIG_PCI_RCAR_GEN2=y
 CONFIG_PCI_RCAR_GEN2_PCIE=y
 CONFIG_PCIEPORTBUS=y
 CONFIG_SMP=y
-CONFIG_NR_CPUS=8
+CONFIG_NR_CPUS=16
 CONFIG_HIGHPTE=y
 CONFIG_CMA=y
 CONFIG_ARM_APPENDED_DTB=y

arch/arm/configs/omap2plus_defconfig

@@ -377,6 +377,7 @@ CONFIG_PWM_TWL=m
 CONFIG_PWM_TWL_LED=m
 CONFIG_OMAP_USB2=m
 CONFIG_TI_PIPE3=y
+CONFIG_TWL4030_USB=m
 CONFIG_EXT2_FS=y
 CONFIG_EXT3_FS=y
 # CONFIG_EXT3_FS_XATTR is not set

arch/arm/configs/sama5_defconfig

@@ -3,8 +3,6 @@
 CONFIG_SYSVIPC=y
 CONFIG_IRQ_DOMAIN_DEBUG=y
 CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED=y
-CONFIG_SYSFS_DEPRECATED_V2=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EMBEDDED=y
 CONFIG_SLAB=y

arch/arm/configs/sunxi_defconfig

@@ -4,6 +4,7 @@ CONFIG_BLK_DEV_INITRD=y
 CONFIG_PERF_EVENTS=y
 CONFIG_ARCH_SUNXI=y
 CONFIG_SMP=y
+CONFIG_NR_CPUS=8
 CONFIG_AEABI=y
 CONFIG_HIGHMEM=y
 CONFIG_HIGHPTE=y

arch/arm/configs/vexpress_defconfig

@@ -118,8 +118,8 @@ CONFIG_HID_ZEROPLUS=y
 CONFIG_USB=y
 CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
 CONFIG_USB_MON=y
-CONFIG_USB_ISP1760_HCD=y
 CONFIG_USB_STORAGE=y
+CONFIG_USB_ISP1760=y
 CONFIG_MMC=y
 CONFIG_MMC_ARMMMCI=y
 CONFIG_NEW_LEDS=y

arch/arm/crypto/aesbs-core.S_shipped

@@ -58,14 +58,18 @@
 # define VFP_ABI_FRAME	0
 # define BSAES_ASM_EXTENDED_KEY
 # define XTS_CHAIN_TWEAK
-# define __ARM_ARCH__	7
+# define __ARM_ARCH__ __LINUX_ARM_ARCH__
+# define __ARM_MAX_ARCH__ 7
 #endif
 
 #ifdef __thumb__
 # define adrl adr
 #endif
 
-#if __ARM_ARCH__>=7
+#if __ARM_MAX_ARCH__>=7
+.arch	armv7-a
+.fpu	neon
+
 .text
 .syntax	unified 	@ ARMv7-capable assembler is expected to handle this
 #ifdef __thumb2__
@@ -74,8 +78,6 @@
 .code   32
 #endif
 
-.fpu	neon
-
 .type	_bsaes_decrypt8,%function
 .align	4
 _bsaes_decrypt8:
@@ -2095,9 +2097,11 @@ bsaes_xts_decrypt:
 	vld1.8	{q8}, [r0]			@ initial tweak
 	adr	r2, .Lxts_magic
 
+#ifndef	XTS_CHAIN_TWEAK
 	tst	r9, #0xf			@ if not multiple of 16
 	it	ne				@ Thumb2 thing, sanity check in ARM
 	subne	r9, #0x10			@ subtract another 16 bytes
+#endif
 	subs	r9, #0x80
 
 	blo	.Lxts_dec_short

arch/arm/crypto/bsaes-armv7.pl

@@ -701,14 +701,18 @@ $code.=<<___;
 # define VFP_ABI_FRAME	0
 # define BSAES_ASM_EXTENDED_KEY
 # define XTS_CHAIN_TWEAK
-# define __ARM_ARCH__	7
+# define __ARM_ARCH__ __LINUX_ARM_ARCH__
+# define __ARM_MAX_ARCH__ 7
 #endif
 
 #ifdef __thumb__
 # define adrl adr
 #endif
 
-#if __ARM_ARCH__>=7
+#if __ARM_MAX_ARCH__>=7
+.arch	armv7-a
+.fpu	neon
+
 .text
 .syntax	unified 	@ ARMv7-capable assembler is expected to handle this
 #ifdef __thumb2__
@@ -717,8 +721,6 @@ $code.=<<___;
 .code   32
 #endif
 
-.fpu	neon
-
 .type	_bsaes_decrypt8,%function
 .align	4
 _bsaes_decrypt8:
@@ -2076,9 +2078,11 @@ bsaes_xts_decrypt:
 	vld1.8	{@XMM[8]}, [r0]			@ initial tweak
 	adr	$magic, .Lxts_magic
 
+#ifndef	XTS_CHAIN_TWEAK
 	tst	$len, #0xf			@ if not multiple of 16
 	it	ne				@ Thumb2 thing, sanity check in ARM
 	subne	$len, #0x10			@ subtract another 16 bytes
+#endif
 	subs	$len, #0x80
 
 	blo	.Lxts_dec_short

arch/arm/include/asm/kvm_mmu.h

@@ -149,29 +149,28 @@ static inline bool kvm_s2pmd_readonly(pmd_t *pmd)
 	(__boundary - 1 < (end) - 1)? __boundary: (end);		\
 })
 
+#define kvm_pgd_index(addr)			pgd_index(addr)
+
 static inline bool kvm_page_empty(void *ptr)
 {
 	struct page *ptr_page = virt_to_page(ptr);
 	return page_count(ptr_page) == 1;
 }
 
-
 #define kvm_pte_table_empty(kvm, ptep) kvm_page_empty(ptep)
 #define kvm_pmd_table_empty(kvm, pmdp) kvm_page_empty(pmdp)
 #define kvm_pud_table_empty(kvm, pudp) (0)
 
 #define KVM_PREALLOC_LEVEL	0
 
-static inline int kvm_prealloc_hwpgd(struct kvm *kvm, pgd_t *pgd)
+static inline void *kvm_get_hwpgd(struct kvm *kvm)
 {
-	return 0;
+	return kvm->arch.pgd;
 }
 
-static inline void kvm_free_hwpgd(struct kvm *kvm) { }
-
-static inline void *kvm_get_hwpgd(struct kvm *kvm)
+static inline unsigned int kvm_get_hwpgd_size(void)
 {
-	return kvm->arch.pgd;
+	return PTRS_PER_S2_PGD * sizeof(pgd_t);
 }
 
 struct kvm;

arch/arm/include/debug/at91.S

@@ -18,8 +18,11 @@
 #define AT91_DBGU 0xfc00c000 /* SAMA5D4_BASE_USART3 */
 #endif
 
-/* Keep in sync with mach-at91/include/mach/hardware.h */
+#ifdef CONFIG_MMU
 #define AT91_IO_P2V(x) ((x) - 0x01000000)
+#else
+#define AT91_IO_P2V(x) (x)
+#endif
 
 #define AT91_DBGU_SR		(0x14)	/* Status Register */
 #define AT91_DBGU_THR		(0x1c)	/* Transmitter Holding Register */

arch/arm/kernel/setup.c

@@ -246,12 +246,9 @@ static int __get_cpu_architecture(void)
 		if (cpu_arch)
 			cpu_arch += CPU_ARCH_ARMv3;
 	} else if ((read_cpuid_id() & 0x000f0000) == 0x000f0000) {
-		unsigned int mmfr0;
-
 		/* Revised CPUID format. Read the Memory Model Feature
 		 * Register 0 and check for VMSAv7 or PMSAv7 */
-		asm("mrc	p15, 0, %0, c0, c1, 4"
-		    : "=r" (mmfr0));
+		unsigned int mmfr0 = read_cpuid_ext(CPUID_EXT_MMFR0);
 		if ((mmfr0 & 0x0000000f) >= 0x00000003 ||
 		    (mmfr0 & 0x000000f0) >= 0x00000030)
 			cpu_arch = CPU_ARCH_ARMv7;

arch/arm/kvm/mmu.c

@@ -290,7 +290,7 @@ static void unmap_range(struct kvm *kvm, pgd_t *pgdp,
 	phys_addr_t addr = start, end = start + size;
 	phys_addr_t next;
 
-	pgd = pgdp + pgd_index(addr);
+	pgd = pgdp + kvm_pgd_index(addr);
 	do {
 		next = kvm_pgd_addr_end(addr, end);
 		if (!pgd_none(*pgd))
@@ -355,7 +355,7 @@ static void stage2_flush_memslot(struct kvm *kvm,
 	phys_addr_t next;
 	pgd_t *pgd;
 
-	pgd = kvm->arch.pgd + pgd_index(addr);
+	pgd = kvm->arch.pgd + kvm_pgd_index(addr);
 	do {
 		next = kvm_pgd_addr_end(addr, end);
 		stage2_flush_puds(kvm, pgd, addr, next);
@@ -632,6 +632,20 @@ int create_hyp_io_mappings(void *from, void *to, phys_addr_t phys_addr)
 				     __phys_to_pfn(phys_addr), PAGE_HYP_DEVICE);
 }
 
+/* Free the HW pgd, one page at a time */
+static void kvm_free_hwpgd(void *hwpgd)
+{
+	free_pages_exact(hwpgd, kvm_get_hwpgd_size());
+}
+
+/* Allocate the HW PGD, making sure that each page gets its own refcount */
+static void *kvm_alloc_hwpgd(void)
+{
+	unsigned int size = kvm_get_hwpgd_size();
+
+	return alloc_pages_exact(size, GFP_KERNEL | __GFP_ZERO);
+}
+
 /**
  * kvm_alloc_stage2_pgd - allocate level-1 table for stage-2 translation.
  * @kvm:	The KVM struct pointer for the VM.
@@ -645,15 +659,31 @@ int create_hyp_io_mappings(void *from, void *to, phys_addr_t phys_addr)
  */
 int kvm_alloc_stage2_pgd(struct kvm *kvm)
 {
-	int ret;
 	pgd_t *pgd;
+	void *hwpgd;
 
 	if (kvm->arch.pgd != NULL) {
 		kvm_err("kvm_arch already initialized?\n");
 		return -EINVAL;
 	}
 
+	hwpgd = kvm_alloc_hwpgd();
+	if (!hwpgd)
+		return -ENOMEM;
+
+	/* When the kernel uses more levels of page tables than the
+	 * guest, we allocate a fake PGD and pre-populate it to point
+	 * to the next-level page table, which will be the real
+	 * initial page table pointed to by the VTTBR.
+	 *
+	 * When KVM_PREALLOC_LEVEL==2, we allocate a single page for
+	 * the PMD and the kernel will use folded pud.
+	 * When KVM_PREALLOC_LEVEL==1, we allocate 2 consecutive PUD
+	 * pages.
+	 */
 	if (KVM_PREALLOC_LEVEL > 0) {
+		int i;
+
 		/*
 		 * Allocate fake pgd for the page table manipulation macros to
 		 * work.  This is not used by the hardware and we have no
@@ -661,30 +691,32 @@ int kvm_alloc_stage2_pgd(struct kvm *kvm)
 		 */
 		pgd = (pgd_t *)kmalloc(PTRS_PER_S2_PGD * sizeof(pgd_t),
 				       GFP_KERNEL | __GFP_ZERO);
+
+		if (!pgd) {
+			kvm_free_hwpgd(hwpgd);
+			return -ENOMEM;
+		}
+
+		/* Plug the HW PGD into the fake one. */
+		for (i = 0; i < PTRS_PER_S2_PGD; i++) {
+			if (KVM_PREALLOC_LEVEL == 1)
+				pgd_populate(NULL, pgd + i,
+					     (pud_t *)hwpgd + i * PTRS_PER_PUD);
+			else if (KVM_PREALLOC_LEVEL == 2)
+				pud_populate(NULL, pud_offset(pgd, 0) + i,
+					     (pmd_t *)hwpgd + i * PTRS_PER_PMD);
+		}
 	} else {
 		/*
 		 * Allocate actual first-level Stage-2 page table used by the
 		 * hardware for Stage-2 page table walks.
 		 */
-		pgd = (pgd_t *)__get_free_pages(GFP_KERNEL | __GFP_ZERO, S2_PGD_ORDER);
+		pgd = (pgd_t *)hwpgd;
 	}
 
-	if (!pgd)
-		return -ENOMEM;
-
-	ret = kvm_prealloc_hwpgd(kvm, pgd);
-	if (ret)
-		goto out_err;
-
 	kvm_clean_pgd(pgd);
 	kvm->arch.pgd = pgd;
 	return 0;
-out_err:
-	if (KVM_PREALLOC_LEVEL > 0)
-		kfree(pgd);
-	else
-		free_pages((unsigned long)pgd, S2_PGD_ORDER);
-	return ret;
 }
 
 /**
@@ -785,11 +817,10 @@ void kvm_free_stage2_pgd(struct kvm *kvm)
 		return;
 
 	unmap_stage2_range(kvm, 0, KVM_PHYS_SIZE);
-	kvm_free_hwpgd(kvm);
+	kvm_free_hwpgd(kvm_get_hwpgd(kvm));
 	if (KVM_PREALLOC_LEVEL > 0)
 		kfree(kvm->arch.pgd);
-	else
-		free_pages((unsigned long)kvm->arch.pgd, S2_PGD_ORDER);
+
 	kvm->arch.pgd = NULL;
 }
 
@@ -799,7 +830,7 @@ static pud_t *stage2_get_pud(struct kvm *kvm, struct kvm_mmu_memory_cache *cache
 	pgd_t *pgd;
 	pud_t *pud;
 
-	pgd = kvm->arch.pgd + pgd_index(addr);
+	pgd = kvm->arch.pgd + kvm_pgd_index(addr);
 	if (WARN_ON(pgd_none(*pgd))) {
 		if (!cache)
 			return NULL;
@@ -1089,7 +1120,7 @@ static void stage2_wp_range(struct kvm *kvm, phys_addr_t addr, phys_addr_t end)
 	pgd_t *pgd;
 	phys_addr_t next;
 
-	pgd = kvm->arch.pgd + pgd_index(addr);
+	pgd = kvm->arch.pgd + kvm_pgd_index(addr);
 	do {
 		/*
 		 * Release kvm_mmu_lock periodically if the memory region is

arch/arm/mach-at91/pm.c

@@ -270,37 +270,35 @@ static void __init at91_pm_sram_init(void)
 	phys_addr_t sram_pbase;
 	unsigned long sram_base;
 	struct device_node *node;
-	struct platform_device *pdev;
+	struct platform_device *pdev = NULL;
 
-	node = of_find_compatible_node(NULL, NULL, "mmio-sram");
-	if (!node) {
-		pr_warn("%s: failed to find sram node!\n", __func__);
-		return;
+	for_each_compatible_node(node, NULL, "mmio-sram") {
+		pdev = of_find_device_by_node(node);
+		if (pdev) {
+			of_node_put(node);
+			break;
+		}
 	}
 
-	pdev = of_find_device_by_node(node);
 	if (!pdev) {
 		pr_warn("%s: failed to find sram device!\n", __func__);
-		goto put_node;
+		return;
 	}
 
 	sram_pool = dev_get_gen_pool(&pdev->dev);
 	if (!sram_pool) {
 		pr_warn("%s: sram pool unavailable!\n", __func__);
-		goto put_node;
+		return;
 	}
 
 	sram_base = gen_pool_alloc(sram_pool, at91_slow_clock_sz);
 	if (!sram_base) {
 		pr_warn("%s: unable to alloc ocram!\n", __func__);
-		goto put_node;
+		return;
 	}
 
 	sram_pbase = gen_pool_virt_to_phys(sram_pool, sram_base);
 	slow_clock = __arm_ioremap_exec(sram_pbase, at91_slow_clock_sz, false);
-
-put_node:
-	of_node_put(node);
 }
 #endif
 

arch/arm/mach-at91/pm.h

@@ -44,7 +44,7 @@ static inline void at91rm9200_standby(void)
 		"    mcr    p15, 0, %0, c7, c0, 4\n\t"
 		"    str    %5, [%1, %2]"
 		:
-		: "r" (0), "r" (AT91_BASE_SYS), "r" (AT91RM9200_SDRAMC_LPR),
+		: "r" (0), "r" (at91_ramc_base[0]), "r" (AT91RM9200_SDRAMC_LPR),
 		  "r" (1), "r" (AT91RM9200_SDRAMC_SRR),
 		  "r" (lpr));
 }

arch/arm/mach-at91/pm_slowclock.S

@@ -25,11 +25,6 @@
  */
 #undef SLOWDOWN_MASTER_CLOCK
 
-#define MCKRDY_TIMEOUT		1000
-#define MOSCRDY_TIMEOUT 	1000
-#define PLLALOCK_TIMEOUT	1000
-#define PLLBLOCK_TIMEOUT	1000
-
 pmc	.req	r0
 sdramc	.req	r1
 ramc1	.req	r2
@@ -41,60 +36,42 @@ tmp2	.req	r5
  * Wait until master clock is ready (after switching master clock source)
  */
 	.macro wait_mckrdy
-	mov	tmp2, #MCKRDY_TIMEOUT
-1:	sub	tmp2, tmp2, #1
-	cmp	tmp2, #0
-	beq	2f
-	ldr	tmp1, [pmc, #AT91_PMC_SR]
+1:	ldr	tmp1, [pmc, #AT91_PMC_SR]
 	tst	tmp1, #AT91_PMC_MCKRDY
 	beq	1b
-2:
 	.endm
 
 /*
  * Wait until master oscillator has stabilized.
  */
 	.macro wait_moscrdy
-	mov	tmp2, #MOSCRDY_TIMEOUT
-1:	sub	tmp2, tmp2, #1
-	cmp	tmp2, #0
-	beq	2f
-	ldr	tmp1, [pmc, #AT91_PMC_SR]
+1:	ldr	tmp1, [pmc, #AT91_PMC_SR]
 	tst	tmp1, #AT91_PMC_MOSCS
 	beq	1b
-2:
 	.endm
 
 /*
  * Wait until PLLA has locked.
  */
 	.macro wait_pllalock
-	mov	tmp2, #PLLALOCK_TIMEOUT
-1:	sub	tmp2, tmp2, #1
-	cmp	tmp2, #0
-	beq	2f
-	ldr	tmp1, [pmc, #AT91_PMC_SR]
+1:	ldr	tmp1, [pmc, #AT91_PMC_SR]
 	tst	tmp1, #AT91_PMC_LOCKA
 	beq	1b
-2:
 	.endm
 
 /*
  * Wait until PLLB has locked.
  */
 	.macro wait_pllblock
-	mov	tmp2, #PLLBLOCK_TIMEOUT
-1:	sub	tmp2, tmp2, #1
-	cmp	tmp2, #0
-	beq	2f
-	ldr	tmp1, [pmc, #AT91_PMC_SR]
+1:	ldr	tmp1, [pmc, #AT91_PMC_SR]
 	tst	tmp1, #AT91_PMC_LOCKB
 	beq	1b
-2:
 	.endm
 
 	.text
 
+	.arm
+
 /* void at91_slow_clock(void __iomem *pmc, void __iomem *sdramc,
  *			void __iomem *ramc1, int memctrl)
  */
@@ -134,6 +111,16 @@ ddr_sr_enable:
 	cmp	memctrl, #AT91_MEMCTRL_DDRSDR
 	bne	sdr_sr_enable
 
+	/* LPDDR1 --> force DDR2 mode during self-refresh */
+	ldr	tmp1, [sdramc, #AT91_DDRSDRC_MDR]
+	str	tmp1, .saved_sam9_mdr
+	bic	tmp1, tmp1, #~AT91_DDRSDRC_MD
+	cmp	tmp1, #AT91_DDRSDRC_MD_LOW_POWER_DDR
+	ldreq	tmp1, [sdramc, #AT91_DDRSDRC_MDR]
+	biceq	tmp1, tmp1, #AT91_DDRSDRC_MD
+	orreq	tmp1, tmp1, #AT91_DDRSDRC_MD_DDR2
+	streq	tmp1, [sdramc, #AT91_DDRSDRC_MDR]
+
 	/* prepare for DDRAM self-refresh mode */
 	ldr	tmp1, [sdramc, #AT91_DDRSDRC_LPR]
 	str	tmp1, .saved_sam9_lpr
@@ -142,14 +129,26 @@ ddr_sr_enable:
 
 	/* figure out if we use the second ram controller */
 	cmp	ramc1, #0
-	ldrne	tmp2, [ramc1, #AT91_DDRSDRC_LPR]
-	strne	tmp2, .saved_sam9_lpr1
-	bicne	tmp2, #AT91_DDRSDRC_LPCB
-	orrne	tmp2, #AT91_DDRSDRC_LPCB_SELF_REFRESH
+	beq	ddr_no_2nd_ctrl
+
+	ldr	tmp2, [ramc1, #AT91_DDRSDRC_MDR]
+	str	tmp2, .saved_sam9_mdr1
+	bic	tmp2, tmp2, #~AT91_DDRSDRC_MD
+	cmp	tmp2, #AT91_DDRSDRC_MD_LOW_POWER_DDR
+	ldreq	tmp2, [ramc1, #AT91_DDRSDRC_MDR]
+	biceq	tmp2, tmp2, #AT91_DDRSDRC_MD
+	orreq	tmp2, tmp2, #AT91_DDRSDRC_MD_DDR2
+	streq	tmp2, [ramc1, #AT91_DDRSDRC_MDR]
+
+	ldr	tmp2, [ramc1, #AT91_DDRSDRC_LPR]
+	str	tmp2, .saved_sam9_lpr1
+	bic	tmp2, #AT91_DDRSDRC_LPCB
+	orr	tmp2, #AT91_DDRSDRC_LPCB_SELF_REFRESH
 
 	/* Enable DDRAM self-refresh mode */
+	str	tmp2, [ramc1, #AT91_DDRSDRC_LPR]
+ddr_no_2nd_ctrl:
 	str	tmp1, [sdramc, #AT91_DDRSDRC_LPR]
-	strne	tmp2, [ramc1, #AT91_DDRSDRC_LPR]
 
 	b	sdr_sr_done
 
@@ -208,6 +207,7 @@ sdr_sr_done:
 	/* Turn off the main oscillator */
 	ldr	tmp1, [pmc, #AT91_CKGR_MOR]
 	bic	tmp1, tmp1, #AT91_PMC_MOSCEN
+	orr	tmp1, tmp1, #AT91_PMC_KEY
 	str	tmp1, [pmc, #AT91_CKGR_MOR]
 
 	/* Wait for interrupt */
@@ -216,6 +216,7 @@ sdr_sr_done:
 	/* Turn on the main oscillator */
 	ldr	tmp1, [pmc, #AT91_CKGR_MOR]
 	orr	tmp1, tmp1, #AT91_PMC_MOSCEN
+	orr	tmp1, tmp1, #AT91_PMC_KEY
 	str	tmp1, [pmc, #AT91_CKGR_MOR]
 
 	wait_moscrdy
@@ -280,12 +281,17 @@ sdr_sr_done:
 	 */
 	cmp	memctrl, #AT91_MEMCTRL_DDRSDR
 	bne	sdr_en_restore
+	/* Restore MDR in case of LPDDR1 */
+	ldr	tmp1, .saved_sam9_mdr
+	str	tmp1, [sdramc, #AT91_DDRSDRC_MDR]
 	/* Restore LPR on AT91 with DDRAM */
 	ldr	tmp1, .saved_sam9_lpr
 	str	tmp1, [sdramc, #AT91_DDRSDRC_LPR]
 
 	/* if we use the second ram controller */
 	cmp	ramc1, #0
+	ldrne	tmp2, .saved_sam9_mdr1
+	strne	tmp2, [ramc1, #AT91_DDRSDRC_MDR]
 	ldrne	tmp2, .saved_sam9_lpr1
 	strne	tmp2, [ramc1, #AT91_DDRSDRC_LPR]
 
@@ -319,5 +325,11 @@ ram_restored:
 .saved_sam9_lpr1:
 	.word 0
 
+.saved_sam9_mdr:
+	.word 0
+
+.saved_sam9_mdr1:
+	.word 0
+
 ENTRY(at91_slow_clock_sz)
 	.word .-at91_slow_clock

arch/arm/mach-exynos/platsmp.c

@@ -126,8 +126,7 @@ static inline void platform_do_lowpower(unsigned int cpu, int *spurious)
  */
 void exynos_cpu_power_down(int cpu)
 {
-	if (cpu == 0 && (of_machine_is_compatible("samsung,exynos5420") ||
-		of_machine_is_compatible("samsung,exynos5800"))) {
+	if (cpu == 0 && (soc_is_exynos5420() || soc_is_exynos5800())) {
 		/*
 		 * Bypass power down for CPU0 during suspend. Check for
 		 * the SYS_PWR_REG value to decide if we are suspending

arch/arm/mach-exynos/pm_domains.c

@@ -161,6 +161,34 @@ no_clk:
 		of_genpd_add_provider_simple(np, &pd->pd);
 	}
 
+	/* Assign the child power domains to their parents */
+	for_each_compatible_node(np, NULL, "samsung,exynos4210-pd") {
+		struct generic_pm_domain *child_domain, *parent_domain;
+		struct of_phandle_args args;
+
+		args.np = np;
+		args.args_count = 0;
+		child_domain = of_genpd_get_from_provider(&args);
+		if (!child_domain)
+			continue;
+
+		if (of_parse_phandle_with_args(np, "power-domains",
+					 "#power-domain-cells", 0, &args) != 0)
+			continue;
+
+		parent_domain = of_genpd_get_from_provider(&args);
+		if (!parent_domain)
+			continue;
+
+		if (pm_genpd_add_subdomain(parent_domain, child_domain))
+			pr_warn("%s failed to add subdomain: %s\n",
+				parent_domain->name, child_domain->name);
+		else
+			pr_info("%s has as child subdomain: %s.\n",
+				parent_domain->name, child_domain->name);
+		of_node_put(np);
+	}
+
 	return 0;
 }
 arch_initcall(exynos4_pm_init_power_domain);

arch/arm/mach-exynos/suspend.c

@@ -87,8 +87,8 @@ static unsigned int exynos_pmu_spare3;
 static u32 exynos_irqwake_intmask = 0xffffffff;
 
 static const struct exynos_wkup_irq exynos3250_wkup_irq[] = {
-	{ 73, BIT(1) }, /* RTC alarm */
-	{ 74, BIT(2) }, /* RTC tick */
+	{ 105, BIT(1) }, /* RTC alarm */
+	{ 106, BIT(2) }, /* RTC tick */
 	{ /* sentinel */ },
 };
 

arch/arm/mach-imx/mach-imx6q.c

@@ -211,8 +211,9 @@ static void __init imx6q_1588_init(void)
 	 * set bit IOMUXC_GPR1[21].  Or the PTP clock must be from pad
 	 * (external OSC), and we need to clear the bit.
 	 */
-	clksel = ptp_clk == enet_ref ? IMX6Q_GPR1_ENET_CLK_SEL_ANATOP :
-				       IMX6Q_GPR1_ENET_CLK_SEL_PAD;
+	clksel = clk_is_match(ptp_clk, enet_ref) ?
+				IMX6Q_GPR1_ENET_CLK_SEL_ANATOP :
+				IMX6Q_GPR1_ENET_CLK_SEL_PAD;
 	gpr = syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
 	if (!IS_ERR(gpr))
 		regmap_update_bits(gpr, IOMUXC_GPR1,

arch/arm/mach-omap2/id.c

@@ -720,6 +720,8 @@ static const char * __init omap_get_family(void)
 		return kasprintf(GFP_KERNEL, "OMAP4");
 	else if (soc_is_omap54xx())
 		return kasprintf(GFP_KERNEL, "OMAP5");
+	else if (soc_is_am33xx() || soc_is_am335x())
+		return kasprintf(GFP_KERNEL, "AM33xx");
 	else if (soc_is_am43xx())
 		return kasprintf(GFP_KERNEL, "AM43xx");
 	else if (soc_is_dra7xx())

arch/arm/mach-omap2/omap_hwmod.c

@@ -1692,16 +1692,15 @@ static int _deassert_hardreset(struct omap_hwmod *oh, const char *name)
 	if (ret == -EBUSY)
 		pr_warn("omap_hwmod: %s: failed to hardreset\n", oh->name);
 
-	if (!ret) {
+	if (oh->clkdm) {
 		/*
 		 * Set the clockdomain to HW_AUTO, assuming that the
 		 * previous state was HW_AUTO.
 		 */
-		if (oh->clkdm && hwsup)
+		if (hwsup)
 			clkdm_allow_idle(oh->clkdm);
-	} else {
-		if (oh->clkdm)
-			clkdm_hwmod_disable(oh->clkdm, oh);
+
+		clkdm_hwmod_disable(oh->clkdm, oh);
 	}
 
 	return ret;
@@ -2698,6 +2697,7 @@ static int __init _register(struct omap_hwmod *oh)
 	INIT_LIST_HEAD(&oh->master_ports);
 	INIT_LIST_HEAD(&oh->slave_ports);
 	spin_lock_init(&oh->_lock);
+	lockdep_set_class(&oh->_lock, &oh->hwmod_key);
 
 	oh->_state = _HWMOD_STATE_REGISTERED;
 

arch/arm/mach-omap2/omap_hwmod.h

@@ -674,6 +674,7 @@ struct omap_hwmod {
 	u32				_sysc_cache;
 	void __iomem			*_mpu_rt_va;
 	spinlock_t			_lock;
+	struct lock_class_key		hwmod_key; /* unique lock class */
 	struct list_head		node;
 	struct omap_hwmod_ocp_if	*_mpu_port;
 	unsigned int			(*xlate_irq)(unsigned int);

arch/arm/mach-omap2/omap_hwmod_7xx_data.c

@@ -1466,53 +1466,16 @@ static struct omap_hwmod dra7xx_ocp2scp3_hwmod = {
  *
  */
 
-static struct omap_hwmod_class dra7xx_pcie_hwmod_class = {
+static struct omap_hwmod_class dra7xx_pciess_hwmod_class = {
 	.name	= "pcie",
 };
 
 /* pcie1 */
-static struct omap_hwmod dra7xx_pcie1_hwmod = {
+static struct omap_hwmod dra7xx_pciess1_hwmod = {
 	.name		= "pcie1",
-	.class		= &dra7xx_pcie_hwmod_class,
+	.class		= &dra7xx_pciess_hwmod_class,
 	.clkdm_name	= "pcie_clkdm",
 	.main_clk	= "l4_root_clk_div",
-	.prcm = {
-		.omap4 = {
-			.clkctrl_offs	= DRA7XX_CM_PCIE_CLKSTCTRL_OFFSET,
-			.modulemode	= MODULEMODE_SWCTRL,
-		},
-	},
-};
-
-/* pcie2 */
-static struct omap_hwmod dra7xx_pcie2_hwmod = {
-	.name		= "pcie2",
-	.class		= &dra7xx_pcie_hwmod_class,
-	.clkdm_name	= "pcie_clkdm",
-	.main_clk	= "l4_root_clk_div",
-	.prcm = {
-		.omap4 = {
-			.clkctrl_offs = DRA7XX_CM_PCIE_CLKSTCTRL_OFFSET,
-			.modulemode   = MODULEMODE_SWCTRL,
-		},
-	},
-};
-
-/*
- * 'PCIE PHY' class
- *
- */
-
-static struct omap_hwmod_class dra7xx_pcie_phy_hwmod_class = {
-	.name	= "pcie-phy",
-};
-
-/* pcie1 phy */
-static struct omap_hwmod dra7xx_pcie1_phy_hwmod = {
-	.name		= "pcie1-phy",
-	.class		= &dra7xx_pcie_phy_hwmod_class,
-	.clkdm_name	= "l3init_clkdm",
-	.main_clk	= "l4_root_clk_div",
 	.prcm = {
 		.omap4 = {
 			.clkctrl_offs = DRA7XX_CM_L3INIT_PCIESS1_CLKCTRL_OFFSET,
@@ -1522,11 +1485,11 @@ static struct omap_hwmod dra7xx_pcie1_phy_hwmod = {
 	},
 };
 
-/* pcie2 phy */
-static struct omap_hwmod dra7xx_pcie2_phy_hwmod = {
-	.name		= "pcie2-phy",
-	.class		= &dra7xx_pcie_phy_hwmod_class,
-	.clkdm_name	= "l3init_clkdm",
+/* pcie2 */
+static struct omap_hwmod dra7xx_pciess2_hwmod = {
+	.name		= "pcie2",
+	.class		= &dra7xx_pciess_hwmod_class,
+	.clkdm_name	= "pcie_clkdm",
 	.main_clk	= "l4_root_clk_div",
 	.prcm = {
 		.omap4 = {
@@ -2877,50 +2840,34 @@ static struct omap_hwmod_ocp_if dra7xx_l4_cfg__ocp2scp3 = {
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
-/* l3_main_1 -> pcie1 */
-static struct omap_hwmod_ocp_if dra7xx_l3_main_1__pcie1 = {
+/* l3_main_1 -> pciess1 */
+static struct omap_hwmod_ocp_if dra7xx_l3_main_1__pciess1 = {
 	.master		= &dra7xx_l3_main_1_hwmod,
-	.slave		= &dra7xx_pcie1_hwmod,
+	.slave		= &dra7xx_pciess1_hwmod,
 	.clk		= "l3_iclk_div",
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
-/* l4_cfg -> pcie1 */
-static struct omap_hwmod_ocp_if dra7xx_l4_cfg__pcie1 = {
+/* l4_cfg -> pciess1 */
+static struct omap_hwmod_ocp_if dra7xx_l4_cfg__pciess1 = {
 	.master		= &dra7xx_l4_cfg_hwmod,
-	.slave		= &dra7xx_pcie1_hwmod,
+	.slave		= &dra7xx_pciess1_hwmod,
 	.clk		= "l4_root_clk_div",
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
-/* l3_main_1 -> pcie2 */
-static struct omap_hwmod_ocp_if dra7xx_l3_main_1__pcie2 = {
+/* l3_main_1 -> pciess2 */
+static struct omap_hwmod_ocp_if dra7xx_l3_main_1__pciess2 = {
 	.master		= &dra7xx_l3_main_1_hwmod,
-	.slave		= &dra7xx_pcie2_hwmod,
+	.slave		= &dra7xx_pciess2_hwmod,
 	.clk		= "l3_iclk_div",
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
-/* l4_cfg -> pcie2 */
-static struct omap_hwmod_ocp_if dra7xx_l4_cfg__pcie2 = {
-	.master		= &dra7xx_l4_cfg_hwmod,
-	.slave		= &dra7xx_pcie2_hwmod,
-	.clk		= "l4_root_clk_div",
-	.user		= OCP_USER_MPU | OCP_USER_SDMA,
-};
-
-/* l4_cfg -> pcie1 phy */
-static struct omap_hwmod_ocp_if dra7xx_l4_cfg__pcie1_phy = {
-	.master		= &dra7xx_l4_cfg_hwmod,
-	.slave		= &dra7xx_pcie1_phy_hwmod,
-	.clk		= "l4_root_clk_div",
-	.user		= OCP_USER_MPU | OCP_USER_SDMA,
-};
-
-/* l4_cfg -> pcie2 phy */
-static struct omap_hwmod_ocp_if dra7xx_l4_cfg__pcie2_phy = {
+/* l4_cfg -> pciess2 */
+static struct omap_hwmod_ocp_if dra7xx_l4_cfg__pciess2 = {
 	.master		= &dra7xx_l4_cfg_hwmod,
-	.slave		= &dra7xx_pcie2_phy_hwmod,
+	.slave		= &dra7xx_pciess2_hwmod,
 	.clk		= "l4_root_clk_div",
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
@@ -3327,12 +3274,10 @@ static struct omap_hwmod_ocp_if *dra7xx_hwmod_ocp_ifs[] __initdata = {
 	&dra7xx_l4_cfg__mpu,
 	&dra7xx_l4_cfg__ocp2scp1,
 	&dra7xx_l4_cfg__ocp2scp3,
-	&dra7xx_l3_main_1__pcie1,
-	&dra7xx_l4_cfg__pcie1,
-	&dra7xx_l3_main_1__pcie2,
-	&dra7xx_l4_cfg__pcie2,
-	&dra7xx_l4_cfg__pcie1_phy,
-	&dra7xx_l4_cfg__pcie2_phy,
+	&dra7xx_l3_main_1__pciess1,
+	&dra7xx_l4_cfg__pciess1,
+	&dra7xx_l3_main_1__pciess2,
+	&dra7xx_l4_cfg__pciess2,
 	&dra7xx_l3_main_1__qspi,
 	&dra7xx_l4_per3__rtcss,
 	&dra7xx_l4_cfg__sata,

arch/arm/mach-omap2/pdata-quirks.c

@@ -173,6 +173,7 @@ static void __init omap3_igep0030_rev_g_legacy_init(void)
 
 static void __init omap3_evm_legacy_init(void)
 {
+	hsmmc2_internal_input_clk();
 	legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 149);
 }
 

arch/arm/mach-omap2/prm44xx.c

@@ -252,10 +252,10 @@ static void omap44xx_prm_save_and_clear_irqen(u32 *saved_mask)
 {
 	saved_mask[0] =
 		omap4_prm_read_inst_reg(OMAP4430_PRM_OCP_SOCKET_INST,
-					OMAP4_PRM_IRQSTATUS_MPU_OFFSET);
+					OMAP4_PRM_IRQENABLE_MPU_OFFSET);
 	saved_mask[1] =
 		omap4_prm_read_inst_reg(OMAP4430_PRM_OCP_SOCKET_INST,
-					OMAP4_PRM_IRQSTATUS_MPU_2_OFFSET);
+					OMAP4_PRM_IRQENABLE_MPU_2_OFFSET);
 
 	omap4_prm_write_inst_reg(0, OMAP4430_PRM_OCP_SOCKET_INST,
 				 OMAP4_PRM_IRQENABLE_MPU_OFFSET);

arch/arm/mach-pxa/idp.c

@@ -36,6 +36,7 @@
 #include <linux/platform_data/video-pxafb.h>
 #include <mach/bitfield.h>
 #include <linux/platform_data/mmc-pxamci.h>
+#include <linux/smc91x.h>
 
 #include "generic.h"
 #include "devices.h"

arch/arm/mach-pxa/irq.c

@@ -11,6 +11,7 @@
  *  it under the terms of the GNU General Public License version 2 as
  *  published by the Free Software Foundation.
  */
+#include <linux/bitops.h>
 #include <linux/init.h>
 #include <linux/module.h>
 #include <linux/interrupt.h>
@@ -40,7 +41,6 @@
 #define ICHP_VAL_IRQ		(1 << 31)
 #define ICHP_IRQ(i)		(((i) >> 16) & 0x7fff)
 #define IPR_VALID		(1 << 31)
-#define IRQ_BIT(n)		(((n) - PXA_IRQ(0)) & 0x1f)
 
 #define MAX_INTERNAL_IRQS	128
 
@@ -51,6 +51,7 @@
 static void __iomem *pxa_irq_base;
 static int pxa_internal_irq_nr;
 static bool cpu_has_ipr;
+static struct irq_domain *pxa_irq_domain;
 
 static inline void __iomem *irq_base(int i)
 {
@@ -66,18 +67,20 @@ static inline void __iomem *irq_base(int i)
 void pxa_mask_irq(struct irq_data *d)
 {
 	void __iomem *base = irq_data_get_irq_chip_data(d);
+	irq_hw_number_t irq = irqd_to_hwirq(d);
 	uint32_t icmr = __raw_readl(base + ICMR);
 
-	icmr &= ~(1 << IRQ_BIT(d->irq));
+	icmr &= ~BIT(irq & 0x1f);
 	__raw_writel(icmr, base + ICMR);
 }
 
 void pxa_unmask_irq(struct irq_data *d)
 {
 	void __iomem *base = irq_data_get_irq_chip_data(d);
+	irq_hw_number_t irq = irqd_to_hwirq(d);
 	uint32_t icmr = __raw_readl(base + ICMR);
 
-	icmr |= 1 << IRQ_BIT(d->irq);
+	icmr |= BIT(irq & 0x1f);
 	__raw_writel(icmr, base + ICMR);
 }
 
@@ -118,40 +121,63 @@ asmlinkage void __exception_irq_entry ichp_handle_irq(struct pt_regs *regs)
 	} while (1);
 }
 
-void __init pxa_init_irq(int irq_nr, int (*fn)(struct irq_data *, unsigned int))
+static int pxa_irq_map(struct irq_domain *h, unsigned int virq,
+		       irq_hw_number_t hw)
 {
-	int irq, i, n;
+	void __iomem *base = irq_base(hw / 32);
 
-	BUG_ON(irq_nr > MAX_INTERNAL_IRQS);
+	/* initialize interrupt priority */
+	if (cpu_has_ipr)
+		__raw_writel(hw | IPR_VALID, pxa_irq_base + IPR(hw));
+
+	irq_set_chip_and_handler(virq, &pxa_internal_irq_chip,
+				 handle_level_irq);
+	irq_set_chip_data(virq, base);
+	set_irq_flags(virq, IRQF_VALID);
+
+	return 0;
+}
+
+static struct irq_domain_ops pxa_irq_ops = {
+	.map    = pxa_irq_map,
+	.xlate  = irq_domain_xlate_onecell,
+};
+
+static __init void
+pxa_init_irq_common(struct device_node *node, int irq_nr,
+		    int (*fn)(struct irq_data *, unsigned int))
+{
+	int n;
 
 	pxa_internal_irq_nr = irq_nr;
-	cpu_has_ipr = !cpu_is_pxa25x();
-	pxa_irq_base = io_p2v(0x40d00000);
+	pxa_irq_domain = irq_domain_add_legacy(node, irq_nr,
+					       PXA_IRQ(0), 0,
+					       &pxa_irq_ops, NULL);
+	if (!pxa_irq_domain)
+		panic("Unable to add PXA IRQ domain\n");
+	irq_set_default_host(pxa_irq_domain);
 
 	for (n = 0; n < irq_nr; n += 32) {
 		void __iomem *base = irq_base(n >> 5);
 
 		__raw_writel(0, base + ICMR);	/* disable all IRQs */
 		__raw_writel(0, base + ICLR);	/* all IRQs are IRQ, not FIQ */
-		for (i = n; (i < (n + 32)) && (i < irq_nr); i++) {
-			/* initialize interrupt priority */
-			if (cpu_has_ipr)
-				__raw_writel(i | IPR_VALID, pxa_irq_base + IPR(i));
-
-			irq = PXA_IRQ(i);
-			irq_set_chip_and_handler(irq, &pxa_internal_irq_chip,
-						 handle_level_irq);
-			irq_set_chip_data(irq, base);
-			set_irq_flags(irq, IRQF_VALID);
-		}
 	}
-
 	/* only unmasked interrupts kick us out of idle */
 	__raw_writel(1, irq_base(0) + ICCR);
 
 	pxa_internal_irq_chip.irq_set_wake = fn;
 }
 
+void __init pxa_init_irq(int irq_nr, int (*fn)(struct irq_data *, unsigned int))
+{
+	BUG_ON(irq_nr > MAX_INTERNAL_IRQS);
+
+	pxa_irq_base = io_p2v(0x40d00000);
+	cpu_has_ipr = !cpu_is_pxa25x();
+	pxa_init_irq_common(NULL, irq_nr, fn);
+}
+
 #ifdef CONFIG_PM
 static unsigned long saved_icmr[MAX_INTERNAL_IRQS/32];
 static unsigned long saved_ipr[MAX_INTERNAL_IRQS];
@@ -203,30 +229,6 @@ struct syscore_ops pxa_irq_syscore_ops = {
 };
 
 #ifdef CONFIG_OF
-static struct irq_domain *pxa_irq_domain;
-
-static int pxa_irq_map(struct irq_domain *h, unsigned int virq,
-		       irq_hw_number_t hw)
-{
-	void __iomem *base = irq_base(hw / 32);
-
-	/* initialize interrupt priority */
-	if (cpu_has_ipr)
-		__raw_writel(hw | IPR_VALID, pxa_irq_base + IPR(hw));
-
-	irq_set_chip_and_handler(hw, &pxa_internal_irq_chip,
-				 handle_level_irq);
-	irq_set_chip_data(hw, base);
-	set_irq_flags(hw, IRQF_VALID);
-
-	return 0;
-}
-
-static struct irq_domain_ops pxa_irq_ops = {
-	.map    = pxa_irq_map,
-	.xlate  = irq_domain_xlate_onecell,
-};
-
 static const struct of_device_id intc_ids[] __initconst = {
 	{ .compatible = "marvell,pxa-intc", },
 	{}
@@ -236,7 +238,7 @@ void __init pxa_dt_irq_init(int (*fn)(struct irq_data *, unsigned int))
 {
 	struct device_node *node;
 	struct resource res;
-	int n, ret;
+	int ret;
 
 	node = of_find_matching_node(NULL, intc_ids);
 	if (!node) {
@@ -267,23 +269,6 @@ void __init pxa_dt_irq_init(int (*fn)(struct irq_data *, unsigned int))
 		return;
 	}
 
-	pxa_irq_domain = irq_domain_add_legacy(node, pxa_internal_irq_nr, 0, 0,
-					       &pxa_irq_ops, NULL);
-	if (!pxa_irq_domain)
-		panic("Unable to add PXA IRQ domain\n");
-
-	irq_set_default_host(pxa_irq_domain);
-
-	for (n = 0; n < pxa_internal_irq_nr; n += 32) {
-		void __iomem *base = irq_base(n >> 5);
-
-		__raw_writel(0, base + ICMR);	/* disable all IRQs */
-		__raw_writel(0, base + ICLR);	/* all IRQs are IRQ, not FIQ */
-	}
-
-	/* only unmasked interrupts kick us out of idle */
-	__raw_writel(1, irq_base(0) + ICCR);
-
-	pxa_internal_irq_chip.irq_set_wake = fn;
+	pxa_init_irq_common(node, pxa_internal_irq_nr, fn);
 }
 #endif /* CONFIG_OF */

arch/arm/mach-pxa/lpd270.c

@@ -195,7 +195,7 @@ static struct resource smc91x_resources[] = {
 };
 
 struct smc91x_platdata smc91x_platdata = {
-	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT;
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 };
 
 static struct platform_device smc91x_device = {

arch/arm/mach-pxa/zeus.c

@@ -412,7 +412,7 @@ static struct fixed_voltage_config can_regulator_pdata = {
 };
 
 static struct platform_device can_regulator_device = {
-	.name	= "reg-fixed-volage",
+	.name	= "reg-fixed-voltage",
 	.id	= 0,
 	.dev	= {
 		.platform_data	= &can_regulator_pdata,

arch/arm/mach-sa1100/neponset.c

@@ -268,8 +268,8 @@ static int neponset_probe(struct platform_device *dev)
 		.id = 0,
 		.res = smc91x_resources,
 		.num_res = ARRAY_SIZE(smc91x_resources),
-		.data = &smc91c_platdata,
-		.size_data = sizeof(smc91c_platdata),
+		.data = &smc91x_platdata,
+		.size_data = sizeof(smc91x_platdata),
 	};
 	int ret, irq;
 

arch/arm/mach-sa1100/pleb.c

@@ -54,7 +54,7 @@ static struct platform_device smc91x_device = {
 	.num_resources	= ARRAY_SIZE(smc91x_resources),
 	.resource	= smc91x_resources,
 	.dev = {
-		.platform_data  = &smc91c_platdata,
+		.platform_data  = &smc91x_platdata,
 	},
 };
 

arch/arm/mach-socfpga/core.h

@@ -45,6 +45,6 @@ extern char secondary_trampoline, secondary_trampoline_end;
 
 extern unsigned long socfpga_cpu1start_addr;
 
-#define SOCFPGA_SCU_VIRT_BASE   0xfffec000
+#define SOCFPGA_SCU_VIRT_BASE   0xfee00000
 
 #endif

arch/arm/mach-socfpga/socfpga.c

@@ -23,6 +23,7 @@
 #include <asm/hardware/cache-l2x0.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
+#include <asm/cacheflush.h>
 
 #include "core.h"
 
@@ -73,6 +74,10 @@ void __init socfpga_sysmgr_init(void)
 			(u32 *) &socfpga_cpu1start_addr))
 		pr_err("SMP: Need cpu1-start-addr in device tree.\n");
 
+	/* Ensure that socfpga_cpu1start_addr is visible to other CPUs */
+	smp_wmb();
+	sync_cache_w(&socfpga_cpu1start_addr);
+
 	sys_manager_base_addr = of_iomap(np, 0);
 
 	np = of_find_compatible_node(NULL, NULL, "altr,rst-mgr");

arch/arm/mach-sti/board-dt.c

@@ -18,6 +18,7 @@ static const char *stih41x_dt_match[] __initdata = {
 	"st,stih415",
 	"st,stih416",
 	"st,stih407",
+	"st,stih410",
 	"st,stih418",
 	NULL
 };

arch/arm/mach-sunxi/Kconfig

@@ -1,10 +1,12 @@
 menuconfig ARCH_SUNXI
 	bool "Allwinner SoCs" if ARCH_MULTI_V7
 	select ARCH_REQUIRE_GPIOLIB
+	select ARCH_HAS_RESET_CONTROLLER
 	select CLKSRC_MMIO
 	select GENERIC_IRQ_CHIP
 	select PINCTRL
 	select SUN4I_TIMER
+	select RESET_CONTROLLER
 
 if ARCH_SUNXI
 
@@ -20,10 +22,8 @@ config MACH_SUN5I
 config MACH_SUN6I
 	bool "Allwinner A31 (sun6i) SoCs support"
 	default ARCH_SUNXI
-	select ARCH_HAS_RESET_CONTROLLER
 	select ARM_GIC
 	select MFD_SUN6I_PRCM
-	select RESET_CONTROLLER
 	select SUN5I_HSTIMER
 
 config MACH_SUN7I
@@ -37,16 +37,12 @@ config MACH_SUN7I
 config MACH_SUN8I
 	bool "Allwinner A23 (sun8i) SoCs support"
 	default ARCH_SUNXI
-	select ARCH_HAS_RESET_CONTROLLER
 	select ARM_GIC
 	select MFD_SUN6I_PRCM
-	select RESET_CONTROLLER
 
 config MACH_SUN9I
 	bool "Allwinner (sun9i) SoCs support"
 	default ARCH_SUNXI
-	select ARCH_HAS_RESET_CONTROLLER
 	select ARM_GIC
-	select RESET_CONTROLLER
 
 endif

arch/arm/mm/cache-l2x0.c

@@ -1131,23 +1131,22 @@ static void __init l2c310_of_parse(const struct device_node *np,
 	}
 
 	ret = l2x0_cache_size_of_parse(np, aux_val, aux_mask, &assoc, SZ_512K);
-	if (ret)
-		return;
-
-	switch (assoc) {
-	case 16:
-		*aux_val &= ~L2X0_AUX_CTRL_ASSOC_MASK;
-		*aux_val |= L310_AUX_CTRL_ASSOCIATIVITY_16;
-		*aux_mask &= ~L2X0_AUX_CTRL_ASSOC_MASK;
-		break;
-	case 8:
-		*aux_val &= ~L2X0_AUX_CTRL_ASSOC_MASK;
-		*aux_mask &= ~L2X0_AUX_CTRL_ASSOC_MASK;
-		break;
-	default:
-		pr_err("L2C-310 OF cache associativity %d invalid, only 8 or 16 permitted\n",
-		       assoc);
-		break;
+	if (!ret) {
+		switch (assoc) {
+		case 16:
+			*aux_val &= ~L2X0_AUX_CTRL_ASSOC_MASK;
+			*aux_val |= L310_AUX_CTRL_ASSOCIATIVITY_16;
+			*aux_mask &= ~L2X0_AUX_CTRL_ASSOC_MASK;
+			break;
+		case 8:
+			*aux_val &= ~L2X0_AUX_CTRL_ASSOC_MASK;
+			*aux_mask &= ~L2X0_AUX_CTRL_ASSOC_MASK;
+			break;
+		default:
+			pr_err("L2C-310 OF cache associativity %d invalid, only 8 or 16 permitted\n",
+			       assoc);
+			break;
+		}
 	}
 
 	prefetch = l2x0_saved_regs.prefetch_ctrl;