Merge branch 'omap-for-v4.15/fixes-dt' into omap-for-v4.15/ti-sysc

Documentation/devicetree/bindings/arm/omap/ctrl.txt

@@ -21,6 +21,8 @@ Required properties:
 		"ti,omap3-scm"
 		"ti,omap4-scm-core"
 		"ti,omap4-scm-padconf-core"
+		"ti,omap4-scm-wkup"
+		"ti,omap4-scm-padconf-wkup"
 		"ti,omap5-scm-core"
 		"ti,omap5-scm-padconf-core"
 		"ti,dra7-scm-core"

Documentation/devicetree/bindings/bus/ti-sysc.txt

@@ -0,0 +1,93 @@
+Texas Instruments sysc interconnect target module wrapper binding
+
+Texas Instruments SoCs can have a generic interconnect target module
+hardware for devices connected to various interconnects such as L3
+interconnect (Arteris NoC) and L4 interconnect (Sonics s3220). The sysc
+is mostly used for interaction between module and PRCM. It participates
+in the OCP Disconnect Protocol but other than that is mostly independent
+of the interconnect.
+
+Each interconnect target module can have one or more devices connected to
+it. There is a set of control registers for managing interconnect target
+module clocks, idle modes and interconnect level resets for the module.
+
+These control registers are sprinkled into the unused register address
+space of the first child device IP block managed by the interconnect
+target module and typically are named REVISION, SYSCONFIG and SYSSTATUS.
+
+Required standard properties:
+
+- compatible	shall be one of the following generic types:
+
+		"ti,sysc-omap2"
+		"ti,sysc-omap4"
+		"ti,sysc-omap4-simple"
+
+		or one of the following derivative types for hardware
+		needing special workarounds:
+
+		"ti,sysc-omap3430-sr"
+		"ti,sysc-omap3630-sr"
+		"ti,sysc-omap4-sr"
+		"ti,sysc-omap3-sham"
+		"ti,sysc-omap-aes"
+		"ti,sysc-mcasp"
+		"ti,sysc-usb-host-fs"
+
+- reg		shall have register areas implemented for the interconnect
+		target module in question such as revision, sysc and syss
+
+- reg-names	shall contain the register names implemented for the
+		interconnect target module in question such as
+		"rev, "sysc", and "syss"
+
+- ranges	shall contain the interconnect target module IO range
+		available for one or more child device IP blocks managed
+		by the interconnect target module, the ranges may include
+		multiple ranges such as device L4 range for control and
+		parent L3 range for DMA access
+
+Optional properties:
+
+- clocks	clock specifier for each name in the clock-names as
+		specified in the binding documentation for ti-clkctrl,
+		typically available for all interconnect targets on TI SoCs
+		based on omap4 except if it's read-only register in hwauto
+		mode as for example omap4 L4_CFG_CLKCTRL
+
+- clock-names	should contain at least "fck", and optionally also "ick"
+		depending on the SoC and the interconnect target module
+
+- ti,hwmods	optional TI interconnect module name to use legacy
+		hwmod platform data
+
+
+Example: Single instance of MUSB controller on omap4 using interconnect ranges
+using offsets from l4_cfg second segment (0x4a000000 + 0x80000 = 0x4a0ab000):
+
+	target-module@2b000 {		/* 0x4a0ab000, ap 84 12.0 */
+		compatible = "ti,sysc-omap2";
+		ti,hwmods = "usb_otg_hs";
+		reg = <0x2b400 0x4>,
+		      <0x2b404 0x4>,
+		      <0x2b408 0x4>;
+		reg-names = "rev", "sysc", "syss";
+		clocks = <&l3_init_clkctrl OMAP4_USB_OTG_HS_CLKCTRL 0>;
+		clock-names = "fck";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x2b000 0x1000>;
+
+		usb_otg_hs: otg@0 {
+			compatible = "ti,omap4-musb";
+			reg = <0x0 0x7ff>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+			usb-phy = <&usb2_phy>;
+			...
+		};
+	};
+
+Note that other SoCs, such as am335x can have multipe child devices. On am335x
+there are two MUSB instances, two USB PHY instances, and a single CPPI41 DMA
+instance as children of a single interconnet target module.

Documentation/devicetree/bindings/hsi/omap-ssi.txt

@@ -1,10 +1,12 @@
 OMAP SSI controller bindings
 
-OMAP Synchronous Serial Interface (SSI) controller implements a legacy
-variant of MIPI's High Speed Synchronous Serial Interface (HSI).
+OMAP3's Synchronous Serial Interface (SSI) controller implements a
+legacy variant of MIPI's High Speed Synchronous Serial Interface (HSI),
+while the controller found inside OMAP4 is supposed to be fully compliant
+with the HSI standard.
 
 Required properties:
-- compatible:		Should include "ti,omap3-ssi".
+- compatible:		Should include "ti,omap3-ssi" or "ti,omap4-hsi"
 - reg-names:		Contains the values "sys" and "gdd" (in this order).
 - reg:			Contains a matching register specifier for each entry
 			in reg-names.
@@ -27,6 +29,7 @@ Each port is represented as a sub-node of the ti,omap3-ssi device.
 Required Port sub-node properties:
 - compatible:		Should be set to the following value
 			ti,omap3-ssi-port (applicable to OMAP34xx devices)
+			ti,omap4-hsi-port (applicable to OMAP44xx devices)
 - reg-names:		Contains the values "tx" and "rx" (in this order).
 - reg:			Contains a matching register specifier for each entry
 			in reg-names.
@@ -38,6 +41,10 @@ Required Port sub-node properties:
 			property. If it's missing the port will not be
 			enabled.
 
+Optional properties:
+- ti,hwmods:		Shall contain TI interconnect module name if needed
+			by the SoC
+
 Example for Nokia N900:
 
 ssi-controller@48058000 {

Documentation/devicetree/bindings/memory-controllers/ti/emif.txt

@@ -7,8 +7,10 @@ of the EMIF IP and memory parts attached to it.
 
 Required properties:
 - compatible	: Should be of the form "ti,emif-<ip-rev>" where <ip-rev>
-  is the IP revision of the specific EMIF instance.
-		  For am437x should be ti,emif-am4372.
+  is the IP revision of the specific EMIF instance. For newer controllers,
+  compatible should be one of the following:
+  	     "ti,emif-am3352"
+	     "ti,emif-am4372"
 
 - phy-type	: <u32> indicating the DDR phy type. Following are the
   allowed values

Documentation/devicetree/bindings/power/ti-smartreflex.txt

@@ -0,0 +1,47 @@
+Texas Instruments SmartReflex binding
+
+SmartReflex is used to set and adjust the SoC operating points.
+
+
+Required properties:
+
+compatible: Shall be one of the following:
+	    "ti,omap3-smartreflex-core"
+	    "ti,omap3-smartreflex-iva"
+	    "ti,omap4-smartreflex-core"
+	    "ti,omap4-smartreflex-mpu"
+	    "ti,omap4-smartreflex-iva"
+
+reg: Shall contain the device instance IO range
+
+interrupts: Shall contain the device instance interrupt
+
+
+Optional properties:
+
+ti,hwmods: Shall contain the TI interconnect module name if needed
+	   by the SoC
+
+
+Example:
+
+	smartreflex_iva: smartreflex@4a0db000 {
+		compatible = "ti,omap4-smartreflex-iva";
+		reg = <0x4a0db000 0x80>;
+		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+		ti,hwmods = "smartreflex_iva";
+	};
+
+	smartreflex_core: smartreflex@4a0dd000 {
+		compatible = "ti,omap4-smartreflex-core";
+		reg = <0x4a0dd000 0x80>;
+		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+		ti,hwmods = "smartreflex_core";
+	};
+
+	smartreflex_mpu: smartreflex@4a0d9000 {
+		compatible = "ti,omap4-smartreflex-mpu";
+		reg = <0x4a0d9000 0x80>;
+		interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+		ti,hwmods = "smartreflex_mpu";
+	};

arch/arm/boot/dts/am33xx.dtsi

@@ -128,9 +128,11 @@
 		};
 	};
 
-	pmu {
+	pmu@4b000000 {
 		compatible = "arm,cortex-a8-pmu";
 		interrupts = <3>;
+		reg = <0x4b000000 0x1000000>;
+		ti,hwmods = "debugss";
 	};
 
 	/*
@@ -927,6 +929,12 @@
 			};
 		};
 
+		emif: emif@4c000000 {
+			compatible = "ti,emif-am3352";
+			reg = <0x4c000000 0x1000000>;
+			ti,hwmods = "emif";
+		};
+
 		gpmc: gpmc@50000000 {
 			compatible = "ti,am3352-gpmc";
 			ti,hwmods = "gpmc";

arch/arm/boot/dts/dra7.dtsi

@@ -457,6 +457,7 @@
 			#dma-cells = <1>;
 			dma-channels = <32>;
 			dma-requests = <127>;
+			ti,hwmods = "dma_system";
 		};
 
 		edma: edma@43300000 {
@@ -1069,6 +1070,13 @@
 			max-frequency = <192000000>;
 		};
 
+		hdqw1w: 1w@480b2000 {
+			compatible = "ti,omap3-1w";
+			reg = <0x480b2000 0x1000>;
+			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "hdq1w";
+		};
+
 		mmc2: mmc@480b4000 {
 			compatible = "ti,omap4-hsmmc";
 			reg = <0x480b4000 0x400>;
@@ -1489,6 +1497,32 @@
 			};
 		};
 
+		target-module@4a0dd000 {
+			compatible = "ti,sysc-omap4-sr";
+			ti,hwmods = "smartreflex_core";
+			reg = <0x4a0dd000 0x4>,
+			      <0x4a0dd008 0x4>;
+			reg-names = "rev", "sysc";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x4a0dd000 0x001000>;
+
+			/* SmartReflex child device marked reserved in TRM */
+		};
+
+		target-module@4a0d9000 {
+			compatible = "ti,sysc-omap4-sr";
+			ti,hwmods = "smartreflex_mpu";
+			reg = <0x4a0d9000 0x4>,
+			      <0x4a0d9008 0x4>;
+			reg-names = "rev", "sysc";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x4a0d9000 0x001000>;
+
+			/* SmartReflex child device marked reserved in TRM */
+		};
+
 		omap_dwc3_1: omap_dwc3_1@48880000 {
 			compatible = "ti,dwc3";
 			ti,hwmods = "usb_otg_ss1";

arch/arm/boot/dts/omap3.dtsi

@@ -215,6 +215,7 @@
 			#dma-cells = <1>;
 			dma-channels = <32>;
 			dma-requests = <96>;
+			ti,hwmods = "dma";
 		};
 
 		gpio1: gpio@48310000 {

arch/arm/boot/dts/omap4.dtsi

@@ -51,6 +51,17 @@
 		};
 	};
 
+	/*
+	 * Note that 4430 needs cross trigger interface (CTI) supported
+	 * before we can configure the interrupts. This means sampling
+	 * events are not supported for pmu. Note that 4460 does not use
+	 * CTI, see also 4460.dtsi.
+	 */
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		ti,hwmods = "debugss";
+	};
+
 	gic: interrupt-controller@48241000 {
 		compatible = "arm,cortex-a9-gic";
 		interrupt-controller;
@@ -163,6 +174,7 @@
 				#address-cells = <1>;
 				#size-cells = <1>;
 				ranges = <0 0x2000 0x1000>;
+				ti,hwmods = "ctrl_module_core";
 
 				scm_conf: scm_conf@0 {
 					compatible = "syscon";
@@ -175,9 +187,11 @@
 			omap4_padconf_core: scm@100000 {
 				compatible = "ti,omap4-scm-padconf-core",
 					     "simple-bus";
+				reg = <0x100000 0x1000>;
 				#address-cells = <1>;
 				#size-cells = <1>;
 				ranges = <0 0x100000 0x1000>;
+				ti,hwmods = "ctrl_module_pad_core";
 
 				omap4_pmx_core: pinmux@40 {
 					compatible = "ti,omap4-padconf",
@@ -252,17 +266,33 @@
 					};
 				};
 
-				omap4_pmx_wkup: pinmux@1e040 {
-					compatible = "ti,omap4-padconf",
-						     "pinctrl-single";
-					reg = <0x1e040 0x0038>;
+				omap4_scm_wkup: scm@c000 {
+					compatible = "ti,omap4-scm-wkup";
+					reg = <0xc000 0x1000>;
+					ti,hwmods = "ctrl_module_wkup";
+				};
+
+				omap4_padconf_wkup: padconf@1e000 {
+					compatible = "ti,omap4-scm-padconf-wkup",
+						     "simple-bus";
+					reg = <0x1e000 0x1000>;
 					#address-cells = <1>;
-					#size-cells = <0>;
-					#pinctrl-cells = <1>;
-					#interrupt-cells = <1>;
-					interrupt-controller;
-					pinctrl-single,register-width = <16>;
-					pinctrl-single,function-mask = <0x7fff>;
+					#size-cells = <1>;
+					ranges = <0 0x1e000 0x1000>;
+					ti,hwmods = "ctrl_module_pad_wkup";
+
+					omap4_pmx_wkup: pinmux@40 {
+						compatible = "ti,omap4-padconf",
+							     "pinctrl-single";
+						reg = <0x40 0x0038>;
+						#address-cells = <1>;
+						#size-cells = <0>;
+						#pinctrl-cells = <1>;
+						#interrupt-cells = <1>;
+						interrupt-controller;
+						pinctrl-single,register-width = <16>;
+						pinctrl-single,function-mask = <0x7fff>;
+					};
 				};
 			};
 		};
@@ -282,6 +312,7 @@
 			#dma-cells = <1>;
 			dma-channels = <32>;
 			dma-requests = <127>;
+			ti,hwmods = "dma_system";
 		};
 
 		gpio1: gpio@4a310000 {
@@ -351,6 +382,19 @@
 			#interrupt-cells = <2>;
 		};
 
+		target-module@48076000 {
+			compatible = "ti,sysc-omap4";
+			ti,hwmods = "slimbus2";
+			reg = <0x48076000 0x4>,
+			      <0x48076010 0x4>;
+			reg-names = "rev", "sysc";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x48076000 0x001000>;
+
+			/* No child device binding or driver in mainline */
+		};
+
 		elm: elm@48078000 {
 			compatible = "ti,am3352-elm";
 			reg = <0x48078000 0x2000>;
@@ -411,6 +455,57 @@
 			clock-frequency = <48000000>;
 		};
 
+		target-module@4a0db000 {
+			compatible = "ti,sysc-sr";
+			ti,hwmods = "smartreflex_iva";
+			reg = <0x4a0db000 0x4>,
+			      <0x4a0db008 0x4>;
+			reg-names = "rev", "sysc";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x4a0db000 0x001000>;
+
+			smartreflex_iva: smartreflex@0 {
+				compatible = "ti,omap4-smartreflex-iva";
+				reg = <0 0x80>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		target-module@4a0dd000 {
+			compatible = "ti,sysc-sr";
+			ti,hwmods = "smartreflex_core";
+			reg = <0x4a0dd000 0x4>,
+			      <0x4a0dd008 0x4>;
+			reg-names = "rev", "sysc";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x4a0dd000 0x001000>;
+
+			smartreflex_core: smartreflex@0 {
+				compatible = "ti,omap4-smartreflex-core";
+				reg = <0 0x80>;
+				interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		target-module@4a0d9000 {
+			compatible = "ti,sysc-sr";
+			ti,hwmods = "smartreflex_mpu";
+			reg = <0x4a0d9000 0x4>,
+			      <0x4a0d9008 0x4>;
+			reg-names = "rev", "sysc";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x4a0d9000 0x001000>;
+
+			smartreflex_mpu: smartreflex@0 {
+				compatible = "ti,omap4-smartreflex-mpu";
+				reg = <0 0x80>;
+				interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
 		hwspinlock: spinlock@4a0f6000 {
 			compatible = "ti,omap4-hwspinlock";
 			reg = <0x4a0f6000 0x1000>;
@@ -489,6 +584,13 @@
 			dma-names = "tx0", "rx0", "tx1", "rx1";
 		};
 
+		hdqw1w: 1w@480b2000 {
+			compatible = "ti,omap3-1w";
+			reg = <0x480b2000 0x1000>;
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "hdq1w";
+		};
+
 		mcspi3: spi@480b8000 {
 			compatible = "ti,omap4-mcspi";
 			reg = <0x480b8000 0x200>;
@@ -565,6 +667,40 @@
 			dma-names = "tx", "rx";
 		};
 
+		hsi: hsi@4a058000 {
+			compatible = "ti,omap4-hsi";
+			reg = <0x4a058000 0x4000>,
+			      <0x4a05c000 0x1000>;
+			reg-names = "sys", "gdd";
+			ti,hwmods = "hsi";
+
+			clocks = <&hsi_fck>;
+			clock-names = "hsi_fck";
+
+			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "gdd_mpu";
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x4a058000 0x4000>;
+
+			hsi_port1: hsi-port@2000 {
+				compatible = "ti,omap4-hsi-port";
+				reg = <0x2000 0x800>,
+				      <0x2800 0x800>;
+				reg-names = "tx", "rx";
+				interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			hsi_port2: hsi-port@3000 {
+				compatible = "ti,omap4-hsi-port";
+				reg = <0x3000 0x800>,
+				      <0x3800 0x800>;
+				reg-names = "tx", "rx";
+				interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
 		mmu_dsp: mmu@4a066000 {
 			compatible = "ti,omap4-iommu";
 			reg = <0x4a066000 0x100>;
@@ -573,6 +709,19 @@
 			#iommu-cells = <0>;
 		};
 
+		target-module@52000000 {
+			compatible = "ti,sysc-omap4";
+			ti,hwmods = "iss";
+			reg = <0x52000000 0x4>,
+			      <0x52000010 0x4>;
+			reg-names = "rev", "sysc";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x52000000 0x1000000>;
+
+			/* No child device binding, driver in staging */
+		};
+
 		mmu_ipu: mmu@55082000 {
 			compatible = "ti,omap4-iommu";
 			reg = <0x55082000 0x100>;
@@ -589,6 +738,14 @@
 			ti,hwmods = "wd_timer2";
 		};
 
+		wdt3: wdt@40130000 {
+			compatible = "ti,omap4-wdt", "ti,omap3-wdt";
+			reg = <0x40130000 0x80>, /* MPU private access */
+			      <0x49030000 0x80>; /* L3 Interconnect */
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "wd_timer3";
+		};
+
 		mcpdm: mcpdm@40132000 {
 			compatible = "ti,omap4-mcpdm";
 			reg = <0x40132000 0x7f>, /* MPU private access */
@@ -659,6 +816,56 @@
 			status = "disabled";
 		};
 
+		target-module@40128000 {
+			compatible = "ti,sysc-mcasp";
+			ti,hwmods = "mcasp";
+			reg = <0x40128004 0x4>;
+			reg-names = "sysc";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x00000000 0x40128000 0x1000>, /* MPU */
+				 <0x49028000 0x49028000 0x1000>; /* L3 */
+
+			/*
+			 * Child device unsupported by davinci-mcasp. At least
+			 * TX path is disabled for omap4, and only DIT mode
+			 * works with no I2S. See also old Android kernel
+			 * omap-mcasp driver for more information.
+			 */
+		};
+
+		target-module@4012c000 {
+			compatible = "ti,sysc-omap4";
+			ti,hwmods = "slimbus1";
+			reg = <0x4012c000 0x4>,
+			      <0x4012c010 0x4>;
+			reg-names = "rev", "sysc";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x00000000 0x4012c000 0x1000>, /* MPU */
+				 <0x4902c000 0x4902c000 0x1000>; /* L3 */
+
+			/* No child device binding or driver in mainline */
+		};
+
+		target-module@401f1000 {
+			compatible = "ti,sysc-omap4";
+			ti,hwmods = "aess";
+			reg = <0x401f1000 0x4>,
+			      <0x401f1010 0x4>;
+			reg-names = "rev", "sysc";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x00000000 0x401f1000 0x1000>, /* MPU */
+				 <0x490f1000 0x490f1000 0x1000>; /* L3 */
+
+			/*
+			 * No child device binding or driver in mainline.
+			 * See Android tree and related upstreaming efforts
+			 * for the old driver.
+			 */
+		};
+
 		mcbsp4: mcbsp@48096000 {
 			compatible = "ti,omap4-mcbsp";
 			reg = <0x48096000 0xff>; /* L4 Interconnect */
@@ -747,6 +954,19 @@
 			};
 		};
 
+		target-module@4a10a000 {
+			compatible = "ti,sysc-omap4";
+			ti,hwmods = "fdif";
+			reg = <0x4a10a000 0x4>,
+			      <0x4a10a010 0x4>;
+			reg-names = "rev", "sysc";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x4a10a000 0x1000>;
+
+			/* No child device binding or driver in mainline */
+		};
+
 		timer1: timer@4a318000 {
 			compatible = "ti,omap3430-timer";
 			reg = <0x4a318000 0x80>;
@@ -962,6 +1182,22 @@
 			status = "disabled";
 		};
 
+		target-module@56000000 {
+			compatible = "ti,sysc-omap4";
+			ti,hwmods = "gpu";
+			reg = <0x5601fc00 0x4>,
+			      <0x5601fc10 0x4>;
+			reg-names = "rev", "sysc";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x56000000 0x2000000>;
+
+			/*
+			 * Closed source PowerVR driver, no child device
+			 * binding or driver in mainline
+			 */
+		};
+
 		dss: dss@58000000 {
 			compatible = "ti,omap4-dss";
 			reg = <0x58000000 0x80>;

arch/arm/boot/dts/omap5.dtsi

@@ -295,6 +295,7 @@
 			#dma-cells = <1>;
 			dma-channels = <32>;
 			dma-requests = <127>;
+			ti,hwmods = "dma_system";
 		};
 
 		gpio1: gpio@4ae10000 {