Merge branch 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

Pull libata fixes from Tejun Heo:
 "I sat on them too long and it's quite a few this late, but nothing has
  a wide blast area. The changes are...

   - Fix corner cases in SG command handling.

   - Recent introduction of default powersaving mode config option
     exposed several devices with broken powersaving behaviors. A number
     of patches to update the blacklist accordingly.

   - Fix a kernel panic on SAS hotplug.

   - Other misc and device specific updates"

* 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libata: Modify quirks for MX100 to limit NCQ_TRIM quirk to MU01 version
  libata: Make Crucial BX100 500GB LPM quirk apply to all firmware versions
  libata: Apply NOLPM quirk to Crucial M500 480 and 960GB SSDs
  libata: Enable queued TRIM for Samsung SSD 860
  PCI: Add function 1 DMA alias quirk for Highpoint RocketRAID 644L
  ahci: Add PCI-id for the Highpoint Rocketraid 644L card
  ata: do not schedule hot plug if it is a sas host
  libata: disable LPM for Crucial BX100 SSD 500GB drive
  libata: Apply NOLPM quirk to Crucial MX100 512GB SSDs
  libata: update documentation for sysfs interfaces
  ata: sata_rcar: Remove unused variable in sata_rcar_init_controller()
  libata: transport: cleanup documentation of sysfs interface
  sata_rcar: Reset SATA PHY when Salvator-X board resumes
  libata: don't try to pass through NCQ commands to non-NCQ devices
  libata: remove WARN() for DMA or PIO command without data
  libata: fix length validation of ATAPI-relayed SCSI commands
  ata: libahci: fix comment indentation
  ahci: Add check for device presence (PCIe hot unplug) in ahci_stop_engine()
  libata: Fix compile warning with ATA_DEBUG enabled

Documentation/ABI/testing/sysfs-ata

@@ -1,110 +1,139 @@
 What:		/sys/class/ata_...
-Date:		August 2008
-Contact:	Gwendal Grignou<gwendal@google.com>
 Description:
-
-Provide a place in sysfs for storing the ATA topology of the system.  This allows
-retrieving various information about ATA objects.
+		Provide a place in sysfs for storing the ATA topology of the
+		system. This allows retrieving various information about ATA
+		objects.
 
 Files under /sys/class/ata_port
 -------------------------------
 
-	For each port, a directory ataX is created where X is the ata_port_id of
-	the port. The device parent is the ata host device.
+For each port, a directory ataX is created where X is the ata_port_id of the
+port. The device parent is the ata host device.
 
-idle_irq (read)
 
-	Number of IRQ received by the port while idle [some ata HBA only].
+What:		/sys/class/ata_port/ataX/nr_pmp_links
+What:		/sys/class/ata_port/ataX/idle_irq
+Date:		May, 2010
+KernelVersion:	v2.6.37
+Contact:	Gwendal Grignou <gwendal@chromium.org>
+Description:
+		nr_pmp_links:	(RO) If a SATA Port Multiplier (PM) is
+				connected, the number of links behind it.
 
-nr_pmp_links (read)
+		idle_irq:	(RO) Number of IRQ received by the port while
+				idle [some ata HBA only].
 
-	If a SATA Port Multiplier (PM) is connected, number of link behind it.
+
+What:		/sys/class/ata_port/ataX/port_no
+Date:		May, 2013
+KernelVersion:	v3.11
+Contact:	Gwendal Grignou <gwendal@chromium.org>
+Description:
+		(RO) Host local port number. While registering host controller,
+		port numbers are tracked based upon number of ports available on
+		the controller. This attribute is needed by udev for composing
+		persistent links in /dev/disk/by-path.
 
 Files under /sys/class/ata_link
 -------------------------------
 
-	Behind each port, there is a ata_link. If there is a SATA PM in the
-	topology, 15 ata_link objects are created.
-
-	If a link is behind a port, the directory name is linkX, where X is
-	ata_port_id of the port.
-	If a link is behind a PM, its name is linkX.Y where X is ata_port_id
-	of the parent port and Y the PM port.
+Behind each port, there is a ata_link. If there is a SATA PM in the topology, 15
+ata_link objects are created.
 
-hw_sata_spd_limit
+If a link is behind a port, the directory name is linkX, where X is ata_port_id
+of the port. If a link is behind a PM, its name is linkX.Y where X is
+ata_port_id of the parent port and Y the PM port.
 
-	Maximum speed supported by the connected SATA device.
 
-sata_spd_limit
+What:		/sys/class/ata_link/linkX[.Y]/hw_sata_spd_limit
+What:		/sys/class/ata_link/linkX[.Y]/sata_spd_limit
+What:		/sys/class/ata_link/linkX[.Y]/sata_spd
+Date:		May, 2010
+KernelVersion:	v2.6.37
+Contact:	Gwendal Grignou <gwendal@chromium.org>
+Description:
+		hw_sata_spd_limit:	(RO) Maximum speed supported by the
+					connected SATA device.
 
-	Maximum speed imposed by libata.
+		sata_spd_limit:		(RO) Maximum speed imposed by libata.
 
-sata_spd
+		sata_spd:		(RO) Current speed of the link
+					eg. 1.5, 3 Gbps etc.
 
-	Current speed of the link [1.5, 3Gps,...].
 
 Files under /sys/class/ata_device
 ---------------------------------
 
-	Behind each link, up to two ata device are created.
-	The name of the directory is devX[.Y].Z where:
-	- X is ata_port_id of the port where the device is connected,
-	- Y the port of the PM if any, and
-	- Z the device id: for PATA, there is usually 2 devices [0,1],
-	only 1 for SATA.
-
-class
-	Device class. Can be "ata" for disk, "atapi" for packet device,
-	"pmp" for PM, or "none" if no device was found behind the link.
-
-dma_mode
+Behind each link, up to two ata devices are created.
+The name of the directory is devX[.Y].Z where:
+- X is ata_port_id of the port where the device is connected,
+- Y the port of the PM if any, and
+- Z the device id: for PATA, there is usually 2 devices [0,1], only 1 for SATA.
+
+
+What:		/sys/class/ata_device/devX[.Y].Z/spdn_cnt
+What:		/sys/class/ata_device/devX[.Y].Z/gscr
+What:		/sys/class/ata_device/devX[.Y].Z/ering
+What:		/sys/class/ata_device/devX[.Y].Z/id
+What:		/sys/class/ata_device/devX[.Y].Z/pio_mode
+What:		/sys/class/ata_device/devX[.Y].Z/xfer_mode
+What:		/sys/class/ata_device/devX[.Y].Z/dma_mode
+What:		/sys/class/ata_device/devX[.Y].Z/class
+Date:		May, 2010
+KernelVersion:	v2.6.37
+Contact:	Gwendal Grignou <gwendal@chromium.org>
+Description:
+		spdn_cnt:	(RO) Number of times libata decided to lower the
+				speed of link due to errors.
 
-	Transfer modes supported by the device when in DMA mode.
-	Mostly used by PATA device.
+		gscr:		(RO) Cached result of the dump of PM GSCR
+				register. Valid registers are:
 
-pio_mode
+				0:      SATA_PMP_GSCR_PROD_ID,
+				1:	SATA_PMP_GSCR_REV,
+				2:      SATA_PMP_GSCR_PORT_INFO,
+				32:     SATA_PMP_GSCR_ERROR,
+				33:     SATA_PMP_GSCR_ERROR_EN,
+				64:     SATA_PMP_GSCR_FEAT,
+				96:     SATA_PMP_GSCR_FEAT_EN,
+				130:    SATA_PMP_GSCR_SII_GPIO
 
-	Transfer modes supported by the device when in PIO mode.
-	Mostly used by PATA device.
+				Only valid if the device is a PM.
 
-xfer_mode
+		ering:		(RO) Formatted output of the error ring of the
+				device.
 
-	Current transfer mode.
+		id:		(RO) Cached result of IDENTIFY command, as
+				described in ATA8 7.16 and 7.17. Only valid if
+				the device is not a PM.
 
-id
+		pio_mode:	(RO) Transfer modes supported by the device when
+				in PIO mode. Mostly used by PATA device.
 
-	Cached result of IDENTIFY command, as described in ATA8 7.16 and 7.17.
-	Only valid if the device is not a PM.
+		xfer_mode:	(RO) Current transfer mode
 
-gscr
+		dma_mode:	(RO) Transfer modes supported by the device when
+				in DMA mode. Mostly used by PATA device.
 
-	Cached result of the dump of PM GSCR register.
-	Valid registers are:
-	0: 	SATA_PMP_GSCR_PROD_ID,
-	1: 	SATA_PMP_GSCR_REV,
-	2: 	SATA_PMP_GSCR_PORT_INFO,
-	32:	SATA_PMP_GSCR_ERROR,
-	33:	SATA_PMP_GSCR_ERROR_EN,
-	64:	SATA_PMP_GSCR_FEAT,
-	96:	SATA_PMP_GSCR_FEAT_EN,
-	130:	SATA_PMP_GSCR_SII_GPIO
-	Only valid if the device is a PM.
+		class:		(RO) Device class. Can be "ata" for disk,
+				"atapi" for packet device, "pmp" for PM, or
+				"none" if no device was found behind the link.
 
-trim
 
-	Shows the DSM TRIM mode currently used by the device. Valid
-	values are:
-	unsupported:		Drive does not support DSM TRIM
-	unqueued:		Drive supports unqueued DSM TRIM only
-	queued:			Drive supports queued DSM TRIM
-	forced_unqueued:	Drive's queued DSM support is known to be
-				buggy and only unqueued TRIM commands
-				are sent
+What:		/sys/class/ata_device/devX[.Y].Z/trim
+Date:		May, 2015
+KernelVersion:	v4.10
+Contact:	Gwendal Grignou <gwendal@chromium.org>
+Description:
+		(RO) Shows the DSM TRIM mode currently used by the device. Valid
+		values are:
 
-spdn_cnt
+		unsupported:		Drive does not support DSM TRIM
 
-	Number of time libata decided to lower the speed of link due to errors.
+		unqueued:               Drive supports unqueued DSM TRIM only
 
-ering
+		queued:                 Drive supports queued DSM TRIM
 
-	Formatted output of the error ring of the device.
+		forced_unqueued:	Drive's queued DSM support is known to
+					be buggy and only unqueued TRIM commands
+					are sent

Documentation/ABI/testing/sysfs-block-device

@@ -0,0 +1,58 @@
+What:		/sys/block/*/device/sw_activity
+Date:		Jun, 2008
+KernelVersion:	v2.6.27
+Contact:	linux-ide@vger.kernel.org
+Description:
+		(RW) Used by drivers which support software controlled activity
+		LEDs.
+
+		It has the following valid values:
+
+		0	OFF - the LED is not activated on activity
+		1	BLINK_ON - the LED blinks on every 10ms when activity is
+			detected.
+		2	BLINK_OFF - the LED is on when idle, and blinks off
+			every 10ms when activity is detected.
+
+		Note that the user must turn sw_activity OFF it they wish to
+		control the activity LED via the em_message file.
+
+
+What:		/sys/block/*/device/unload_heads
+Date:		Sep, 2008
+KernelVersion:	v2.6.28
+Contact:	linux-ide@vger.kernel.org
+Description:
+		(RW) Hard disk shock protection
+
+		Writing an integer value to this file will take the heads of the
+		respective drive off the platter and block all I/O operations
+		for the specified number of milliseconds.
+
+		- If the device does not support the unload heads feature,
+		  access is denied with -EOPNOTSUPP.
+		- The maximal value accepted for a timeout is 30000
+		  milliseconds.
+		- A previously set timeout can be cancelled and disk can resume
+		  normal operation immediately by specifying a timeout of 0.
+		- Some hard drives only comply with an earlier version of the
+		  ATA standard, but support the unload feature nonetheless.
+		  There is no safe way Linux can detect these devices, so this
+		  is not enabled by default. If it is known that your device
+		  does support the unload feature, then you can tell the kernel
+		  to enable it by writing -1. It can be disabled again by
+		  writing -2.
+		- Values below -2 are rejected with -EINVAL
+
+		For more information, see
+		Documentation/laptops/disk-shock-protection.txt
+
+
+What:		/sys/block/*/device/ncq_prio_enable
+Date:		Oct, 2016
+KernelVersion:	v4.10
+Contact:	linux-ide@vger.kernel.org
+Description:
+		(RW) Write to the file to turn on or off the SATA ncq (native
+		command queueing) support. By default this feature is turned
+		off.

Documentation/ABI/testing/sysfs-class-scsi_host

@@ -27,3 +27,92 @@ Description:	This file contains the current status of the "SSD Smart Path"
 		the direct i/o path to physical devices.  This setting is
 		controller wide, affecting all configured logical drives on the
 		controller.  This file is readable and writable.
+
+What:		/sys/class/scsi_host/hostX/link_power_management_policy
+Date:		Oct, 2007
+KernelVersion:	v2.6.24
+Contact:	linux-ide@vger.kernel.org
+Description:
+		(RW) This parameter allows the user to read and set the link
+		(interface) power management.
+
+		There are four possible options:
+
+		min_power: Tell the controller to try to make the link use the
+		least possible power when possible. This may sacrifice some
+		performance due to increased latency when coming out of lower
+		power states.
+
+		max_performance: Generally, this means no power management.
+		Tell the controller to have performance be a priority over power
+		management.
+
+		medium_power: Tell the controller to enter a lower power state
+		when possible, but do not enter the lowest power state, thus
+		improving latency over min_power setting.
+
+		med_power_with_dipm: Identical to the existing medium_power
+		setting except that it enables dipm (device initiated power
+		management) on top, which makes it match the Windows IRST (Intel
+		Rapid Storage Technology) driver settings. This setting is also
+		close to min_power, except that:
+		a) It does not use host-initiated slumber mode, but it does
+		allow device-initiated slumber
+		b) It does not enable low power device sleep mode (DevSlp).
+
+What:		/sys/class/scsi_host/hostX/em_message
+What:		/sys/class/scsi_host/hostX/em_message_type
+Date:		Jun, 2008
+KernelVersion:	v2.6.27
+Contact:	linux-ide@vger.kernel.org
+Description:
+		em_message: (RW) Enclosure management support. For the LED
+		protocol, writes and reads correspond to the LED message format
+		as defined in the AHCI spec.
+
+		The user must turn sw_activity (under /sys/block/*/device/) OFF
+		it they wish to control the activity LED via the em_message
+		file.
+
+		em_message_type: (RO) Displays the current enclosure management
+		protocol that is being used by the driver (for eg. LED, SAF-TE,
+		SES-2, SGPIO etc).
+
+What:		/sys/class/scsi_host/hostX/ahci_port_cmd
+What:		/sys/class/scsi_host/hostX/ahci_host_caps
+What:		/sys/class/scsi_host/hostX/ahci_host_cap2
+Date:		Mar, 2010
+KernelVersion:	v2.6.35
+Contact:	linux-ide@vger.kernel.org
+Description:
+		[to be documented]
+
+What:		/sys/class/scsi_host/hostX/ahci_host_version
+Date:		Mar, 2010
+KernelVersion:	v2.6.35
+Contact:	linux-ide@vger.kernel.org
+Description:
+		(RO) Display the version of the AHCI spec implemented by the
+		host.
+
+What:		/sys/class/scsi_host/hostX/em_buffer
+Date:		Apr, 2010
+KernelVersion:	v2.6.35
+Contact:	linux-ide@vger.kernel.org
+Description:
+		(RW) Allows access to AHCI EM (enclosure management) buffer
+		directly if the host supports EM.
+
+		For eg. the AHCI driver supports SGPIO EM messages but the
+		SATA/AHCI specs do not define the SGPIO message format of the EM
+		buffer. Different hardware(HW) vendors may have different
+		definitions. With the em_buffer attribute, this issue can be
+		solved by allowing HW vendors to provide userland drivers and
+		tools for their SGPIO initiators.
+
+What:		/sys/class/scsi_host/hostX/em_message_supported
+Date:		Oct, 2009
+KernelVersion:	v2.6.39
+Contact:	linux-ide@vger.kernel.org
+Description:
+		(RO) Displays supported enclosure management message types.

drivers/ata/ahci.c

@@ -550,7 +550,9 @@ static const struct pci_device_id ahci_pci_tbl[] = {
 	  .driver_data = board_ahci_yes_fbs },
 	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL_EXT, 0x9230),
 	  .driver_data = board_ahci_yes_fbs },
-	{ PCI_DEVICE(PCI_VENDOR_ID_TTI, 0x0642),
+	{ PCI_DEVICE(PCI_VENDOR_ID_TTI, 0x0642), /* highpoint rocketraid 642L */
+	  .driver_data = board_ahci_yes_fbs },
+	{ PCI_DEVICE(PCI_VENDOR_ID_TTI, 0x0645), /* highpoint rocketraid 644L */
 	  .driver_data = board_ahci_yes_fbs },
 
 	/* Promise */

drivers/ata/libahci.c

@@ -665,6 +665,16 @@ int ahci_stop_engine(struct ata_port *ap)
 	if ((tmp & (PORT_CMD_START | PORT_CMD_LIST_ON)) == 0)
 		return 0;
 
+	/*
+	 * Don't try to issue commands but return with ENODEV if the
+	 * AHCI controller not available anymore (e.g. due to PCIe hot
+	 * unplugging). Otherwise a 500ms delay for each port is added.
+	 */
+	if (tmp == 0xffffffff) {
+		dev_err(ap->host->dev, "AHCI controller unavailable!\n");
+		return -ENODEV;
+	}
+
 	/* setting HBA to idle */
 	tmp &= ~PORT_CMD_START;
 	writel(tmp, port_mmio + PORT_CMD);

drivers/ata/libahci_platform.c

@@ -340,7 +340,7 @@ static int ahci_platform_get_regulator(struct ahci_host_priv *hpriv, u32 port,
  * 2) regulator for controlling the targets power (optional)
  * 3) 0 - AHCI_MAX_CLKS clocks, as specified in the devs devicetree node,
  *    or for non devicetree enabled platforms a single clock
- *	4) phys (optional)
+ * 4) phys (optional)
  *
  * RETURNS:
  * The allocated ahci_host_priv on success, otherwise an ERR_PTR value

drivers/ata/libata-core.c

@@ -4530,6 +4530,25 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
 	{ "PIONEER DVD-RW  DVR-212D",	NULL,	ATA_HORKAGE_NOSETXFER },
 	{ "PIONEER DVD-RW  DVR-216D",	NULL,	ATA_HORKAGE_NOSETXFER },
 
+	/* Crucial BX100 SSD 500GB has broken LPM support */
+	{ "CT500BX100SSD1",		NULL,	ATA_HORKAGE_NOLPM },
+
+	/* 512GB MX100 with MU01 firmware has both queued TRIM and LPM issues */
+	{ "Crucial_CT512MX100*",	"MU01",	ATA_HORKAGE_NO_NCQ_TRIM |
+						ATA_HORKAGE_ZERO_AFTER_TRIM |
+						ATA_HORKAGE_NOLPM, },
+	/* 512GB MX100 with newer firmware has only LPM issues */
+	{ "Crucial_CT512MX100*",	NULL,	ATA_HORKAGE_ZERO_AFTER_TRIM |
+						ATA_HORKAGE_NOLPM, },
+
+	/* 480GB+ M500 SSDs have both queued TRIM and LPM issues */
+	{ "Crucial_CT480M500*",		NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
+						ATA_HORKAGE_ZERO_AFTER_TRIM |
+						ATA_HORKAGE_NOLPM, },
+	{ "Crucial_CT960M500*",		NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
+						ATA_HORKAGE_ZERO_AFTER_TRIM |
+						ATA_HORKAGE_NOLPM, },
+
 	/* devices that don't properly handle queued TRIM commands */
 	{ "Micron_M500_*",		NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
 						ATA_HORKAGE_ZERO_AFTER_TRIM, },
@@ -4541,7 +4560,9 @@ static const struct ata_blacklist_entry ata_device_blacklist [] = {
 						ATA_HORKAGE_ZERO_AFTER_TRIM, },
 	{ "Crucial_CT*MX100*",		"MU01",	ATA_HORKAGE_NO_NCQ_TRIM |
 						ATA_HORKAGE_ZERO_AFTER_TRIM, },
-	{ "Samsung SSD 8*",		NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
+	{ "Samsung SSD 840*",		NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
+						ATA_HORKAGE_ZERO_AFTER_TRIM, },
+	{ "Samsung SSD 850*",		NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
 						ATA_HORKAGE_ZERO_AFTER_TRIM, },
 	{ "FCCT*M500*",			NULL,	ATA_HORKAGE_NO_NCQ_TRIM |
 						ATA_HORKAGE_ZERO_AFTER_TRIM, },
@@ -5401,8 +5422,7 @@ void ata_qc_issue(struct ata_queued_cmd *qc)
 	 * We guarantee to LLDs that they will have at least one
 	 * non-zero sg if the command is a data command.
 	 */
-	if (WARN_ON_ONCE(ata_is_data(prot) &&
-			 (!qc->sg || !qc->n_elem || !qc->nbytes)))
+	if (ata_is_data(prot) && (!qc->sg || !qc->n_elem || !qc->nbytes))
 		goto sys_err;
 
 	if (ata_is_dma(prot) || (ata_is_pio(prot) &&

drivers/ata/libata-eh.c

@@ -815,7 +815,8 @@ void ata_scsi_port_error_handler(struct Scsi_Host *host, struct ata_port *ap)
 
 	if (ap->pflags & ATA_PFLAG_LOADING)
 		ap->pflags &= ~ATA_PFLAG_LOADING;
-	else if (ap->pflags & ATA_PFLAG_SCSI_HOTPLUG)
+	else if ((ap->pflags & ATA_PFLAG_SCSI_HOTPLUG) &&
+		!(ap->flags & ATA_FLAG_SAS_HOST))
 		schedule_delayed_work(&ap->hotplug_task, 0);
 
 	if (ap->pflags & ATA_PFLAG_RECOVERED)

drivers/ata/libata-scsi.c

@@ -3316,6 +3316,12 @@ static unsigned int ata_scsi_pass_thru(struct ata_queued_cmd *qc)
 		goto invalid_fld;
 	}
 
+	/* We may not issue NCQ commands to devices not supporting NCQ */
+	if (ata_is_ncq(tf->protocol) && !ata_ncq_enabled(dev)) {
+		fp = 1;
+		goto invalid_fld;
+	}
+
 	/* sanity check for pio multi commands */
 	if ((cdb[1] & 0xe0) && !is_multi_taskfile(tf)) {
 		fp = 1;
@@ -4282,7 +4288,7 @@ static inline void ata_scsi_dump_cdb(struct ata_port *ap,
 #ifdef ATA_DEBUG
 	struct scsi_device *scsidev = cmd->device;
 
-	DPRINTK("CDB (%u:%d,%d,%d) %9ph\n",
+	DPRINTK("CDB (%u:%d,%d,%lld) %9ph\n",
 		ap->print_id,
 		scsidev->channel, scsidev->id, scsidev->lun,
 		cmd->cmnd);
@@ -4309,7 +4315,9 @@ static inline int __ata_scsi_queuecmd(struct scsi_cmnd *scmd,
 		if (likely((scsi_op != ATA_16) || !atapi_passthru16)) {
 			/* relay SCSI command to ATAPI device */
 			int len = COMMAND_SIZE(scsi_op);
-			if (unlikely(len > scmd->cmd_len || len > dev->cdb_len))
+			if (unlikely(len > scmd->cmd_len ||
+				     len > dev->cdb_len ||
+				     scmd->cmd_len > ATAPI_CDB_LEN))
 				goto bad_cdb_len;
 
 			xlat_func = atapi_xlat;

drivers/ata/sata_rcar.c

@@ -146,6 +146,7 @@
 enum sata_rcar_type {
 	RCAR_GEN1_SATA,
 	RCAR_GEN2_SATA,
+	RCAR_GEN3_SATA,
 	RCAR_R8A7790_ES1_SATA,
 };
 
@@ -784,26 +785,11 @@ static void sata_rcar_setup_port(struct ata_host *host)
 	ioaddr->command_addr	= ioaddr->cmd_addr + (ATA_REG_CMD << 2);
 }
 
-static void sata_rcar_init_controller(struct ata_host *host)
+static void sata_rcar_init_module(struct sata_rcar_priv *priv)
 {
-	struct sata_rcar_priv *priv = host->private_data;
 	void __iomem *base = priv->base;
 	u32 val;
 
-	/* reset and setup phy */
-	switch (priv->type) {
-	case RCAR_GEN1_SATA:
-		sata_rcar_gen1_phy_init(priv);
-		break;
-	case RCAR_GEN2_SATA:
-	case RCAR_R8A7790_ES1_SATA:
-		sata_rcar_gen2_phy_init(priv);
-		break;
-	default:
-		dev_warn(host->dev, "SATA phy is not initialized\n");
-		break;
-	}
-
 	/* SATA-IP reset state */
 	val = ioread32(base + ATAPI_CONTROL1_REG);
 	val |= ATAPI_CONTROL1_RESET;
@@ -824,10 +810,33 @@ static void sata_rcar_init_controller(struct ata_host *host)
 	/* ack and mask */
 	iowrite32(0, base + SATAINTSTAT_REG);
 	iowrite32(0x7ff, base + SATAINTMASK_REG);
+
 	/* enable interrupts */
 	iowrite32(ATAPI_INT_ENABLE_SATAINT, base + ATAPI_INT_ENABLE_REG);
 }
 
+static void sata_rcar_init_controller(struct ata_host *host)
+{
+	struct sata_rcar_priv *priv = host->private_data;
+
+	/* reset and setup phy */
+	switch (priv->type) {
+	case RCAR_GEN1_SATA:
+		sata_rcar_gen1_phy_init(priv);
+		break;
+	case RCAR_GEN2_SATA:
+	case RCAR_GEN3_SATA:
+	case RCAR_R8A7790_ES1_SATA:
+		sata_rcar_gen2_phy_init(priv);
+		break;
+	default:
+		dev_warn(host->dev, "SATA phy is not initialized\n");
+		break;
+	}
+
+	sata_rcar_init_module(priv);
+}
+
 static const struct of_device_id sata_rcar_match[] = {
 	{
 		/* Deprecated by "renesas,sata-r8a7779" */
@@ -856,7 +865,7 @@ static const struct of_device_id sata_rcar_match[] = {
 	},
 	{
 		.compatible = "renesas,sata-r8a7795",
-		.data = (void *)RCAR_GEN2_SATA
+		.data = (void *)RCAR_GEN3_SATA
 	},
 	{
 		.compatible = "renesas,rcar-gen2-sata",
@@ -864,7 +873,7 @@ static const struct of_device_id sata_rcar_match[] = {
 	},
 	{
 		.compatible = "renesas,rcar-gen3-sata",
-		.data = (void *)RCAR_GEN2_SATA
+		.data = (void *)RCAR_GEN3_SATA
 	},
 	{ },
 };
@@ -982,11 +991,18 @@ static int sata_rcar_resume(struct device *dev)
 	if (ret)
 		return ret;
 
-	/* ack and mask */
-	iowrite32(0, base + SATAINTSTAT_REG);
-	iowrite32(0x7ff, base + SATAINTMASK_REG);
-	/* enable interrupts */
-	iowrite32(ATAPI_INT_ENABLE_SATAINT, base + ATAPI_INT_ENABLE_REG);
+	if (priv->type == RCAR_GEN3_SATA) {
+		sata_rcar_gen2_phy_init(priv);
+		sata_rcar_init_module(priv);
+	} else {
+		/* ack and mask */
+		iowrite32(0, base + SATAINTSTAT_REG);
+		iowrite32(0x7ff, base + SATAINTMASK_REG);
+
+		/* enable interrupts */
+		iowrite32(ATAPI_INT_ENABLE_SATAINT,
+			  base + ATAPI_INT_ENABLE_REG);
+	}
 
 	ata_host_resume(host);
 

drivers/pci/quirks.c

@@ -3908,6 +3908,8 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_MARVELL_EXT, 0x9230,
 			 quirk_dma_func1_alias);
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TTI, 0x0642,
 			 quirk_dma_func1_alias);
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TTI, 0x0645,
+			 quirk_dma_func1_alias);
 /* https://bugs.gentoo.org/show_bug.cgi?id=497630 */
 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_JMICRON,
 			 PCI_DEVICE_ID_JMICRON_JMB388_ESD,