drivers: serial: jsm: Add Classic board UART structure

This commit adds the UART structure for the Digi Classic cards. This
code comes from the staging/dgnc driver.

Signed-off-by: Konrad Zapalowicz <bergo.torino@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/jsm/jsm.h

@@ -222,7 +222,10 @@ struct jsm_channel {
 	u8		ch_mostat;	/* FEP output modem status	*/
 	u8		ch_mistat;	/* FEP input modem status	*/
 
-	struct neo_uart_struct __iomem *ch_neo_uart;	/* Pointer to the "mapped" UART struct */
+	/* Pointers to the "mapped" UART structs */
+	struct neo_uart_struct __iomem *ch_neo_uart; /* NEO card */
+	struct cls_uart_struct __iomem *ch_cls_uart; /* Classic card */
+
 	u8		ch_cached_lsr;	/* Cached value of the LSR register */
 
 	u8		*ch_rqueue;	/* Our read queue buffer - malloc'ed */
@@ -254,6 +257,60 @@ struct jsm_channel {
 	u64		ch_xoff_sends;	/* Count of xoffs transmitted */
 };
 
+/************************************************************************
+ * Per channel/port Classic UART structures				*
+ ************************************************************************
+ *		Base Structure Entries Usage Meanings to Host		*
+ *									*
+ *	W = read write		R = read only				*
+ *			U = Unused.					*
+ ************************************************************************/
+
+struct cls_uart_struct {
+	u8 txrx;	/* WR  RHR/THR - Holding Reg */
+	u8 ier;		/* WR  IER - Interrupt Enable Reg */
+	u8 isr_fcr;	/* WR  ISR/FCR - Interrupt Status Reg/Fifo Control Reg*/
+	u8 lcr;		/* WR  LCR - Line Control Reg */
+	u8 mcr;		/* WR  MCR - Modem Control Reg */
+	u8 lsr;		/* WR  LSR - Line Status Reg */
+	u8 msr;		/* WR  MSR - Modem Status Reg */
+	u8 spr;		/* WR  SPR - Scratch Pad Reg */
+};
+
+/* Where to read the interrupt register (8bits) */
+#define UART_CLASSIC_POLL_ADDR_OFFSET	0x40
+
+#define UART_EXAR654_ENHANCED_REGISTER_SET 0xBF
+
+#define UART_16654_FCR_TXTRIGGER_8	0x0
+#define UART_16654_FCR_TXTRIGGER_16	0x10
+#define UART_16654_FCR_TXTRIGGER_32	0x20
+#define UART_16654_FCR_TXTRIGGER_56	0x30
+
+#define UART_16654_FCR_RXTRIGGER_8	0x0
+#define UART_16654_FCR_RXTRIGGER_16	0x40
+#define UART_16654_FCR_RXTRIGGER_56	0x80
+#define UART_16654_FCR_RXTRIGGER_60	0xC0
+
+#define UART_IIR_CTSRTS			0x20	/* Received CTS/RTS change of state */
+#define UART_IIR_RDI_TIMEOUT		0x0C    /* Receiver data TIMEOUT */
+
+/*
+ * These are the EXTENDED definitions for the Exar 654's Interrupt
+ * Enable Register.
+ */
+#define UART_EXAR654_EFR_ECB      0x10    /* Enhanced control bit */
+#define UART_EXAR654_EFR_IXON     0x2     /* Receiver compares Xon1/Xoff1 */
+#define UART_EXAR654_EFR_IXOFF    0x8     /* Transmit Xon1/Xoff1 */
+#define UART_EXAR654_EFR_RTSDTR   0x40    /* Auto RTS/DTR Flow Control Enable */
+#define UART_EXAR654_EFR_CTSDSR   0x80    /* Auto CTS/DSR Flow COntrol Enable */
+
+#define UART_EXAR654_XOFF_DETECT  0x1     /* Indicates whether chip saw an incoming XOFF char  */
+#define UART_EXAR654_XON_DETECT   0x2     /* Indicates whether chip saw an incoming XON char */
+
+#define UART_EXAR654_IER_XOFF     0x20    /* Xoff Interrupt Enable */
+#define UART_EXAR654_IER_RTSDTR   0x40    /* Output Interrupt Enable */
+#define UART_EXAR654_IER_CTSDSR   0x80    /* Input Interrupt Enable */
 
 /************************************************************************
  * Per channel/port NEO UART structure					*