Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup3

Merge "Samsung 2nd DT updates for v3.15" from Kukjin Kim:

- add DT entry for AHCI SATA and SATA PHY with using generic
  PHY framework for exynos5250 and arndale, smdk5250 boards.
- add SSS DT node for exynos5420 and exynos5250
- remove leftover spi0 node for smdk5250 board
- add ADC and thermistor nodes for exynos4412-trats2 board
- move common irq-combiner node for exynos4x12 from exynos4212
  and exynos4412
- add ADC, PMU and GPS_ALIVE power domain nodes for exynos4x12

Note that based on previous tags/samsung-dt and tags/exynos-clk

* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: enable ahci sata and sata phy for exynos5250
  ARM: dts: add dt node for sss module for exynos5250/5420
  ARM: dts: Remove leftover spi0 node for smdk5250
  ARM: dts: Add ADC and themistor nodes for exynos4412-trats2
  ARM: dts: Move common dt data for interrupt combiner controller for exynos4x12
  ARM: dts: Add GPS_ALIVE power domain for exynos4x12
  ARM: dts: Add PMU dt data to support PMU for exynos4x12
  ARM: dts: Add ADC's dt data to read raw data for exynos4x12

Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/ata/exynos-sata-phy.txt

@@ -1,14 +0,0 @@
-* Samsung SATA PHY Controller
-
-SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
-Each SATA PHY controller should have its own node.
-
-Required properties:
-- compatible        : compatible list, contains "samsung,exynos5-sata-phy"
-- reg               : <registers mapping>
-
-Example:
-        sata@ffe07000 {
-                compatible = "samsung,exynos5-sata-phy";
-                reg = <0xffe07000 0x1000>;
-        };

Documentation/devicetree/bindings/ata/exynos-sata.txt

@@ -4,14 +4,21 @@ SATA nodes are defined to describe on-chip Serial ATA controllers.
 Each SATA controller should have its own node.
 
 Required properties:
-- compatible        : compatible list, contains "samsung,exynos5-sata"
-- interrupts        : <interrupt mapping for SATA IRQ>
-- reg               : <registers mapping>
-- samsung,sata-freq : <frequency in MHz>
+- compatible		: compatible list, contains "samsung,exynos5-sata"
+- interrupts		: <interrupt mapping for SATA IRQ>
+- reg			: <registers mapping>
+- samsung,sata-freq	: <frequency in MHz>
+- phys			: as mentioned in phy-bindings.txt
+- phy-names		: as mentioned in phy-bindings.txt
 
 Example:
-        sata@ffe08000 {
-                compatible = "samsung,exynos5-sata";
-                reg = <0xffe08000 0x1000>;
-                interrupts = <115>;
-        };
+	sata@122f0000 {
+		compatible = "snps,dwc-ahci";
+		samsung,sata-freq = <66>;
+		reg = <0x122f0000 0x1ff>;
+		interrupts = <0 115 0>;
+		clocks = <&clock 277>, <&clock 143>;
+		clock-names = "sata", "sclk_sata";
+		phys = <&sata_phy>;
+		phy-names = "sata-phy";
+	};

Documentation/devicetree/bindings/phy/samsung-phy.txt

@@ -20,3 +20,39 @@ Required properties:
 - compatible : should be "samsung,exynos5250-dp-video-phy";
 - reg : offset and length of the Display Port PHY register set;
 - #phy-cells : from the generic PHY bindings, must be 0;
+
+Samsung SATA PHY Controller
+---------------------------
+
+SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers.
+Each SATA PHY controller should have its own node.
+
+Required properties:
+- compatible        : compatible list, contains "samsung,exynos5250-sata-phy"
+- reg : offset and length of the SATA PHY register set;
+- #phy-cells : from the generic phy bindings;
+
+Example:
+	sata_phy: sata-phy@12170000 {
+		compatible = "samsung,exynos5250-sata-phy";
+		reg = <0x12170000 0x1ff>;
+		clocks = <&clock 287>;
+		clock-names = "sata_phyctrl";
+		#phy-cells = <0>;
+		samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>;
+		samsung,syscon-phandle = <&pmu_syscon>;
+	};
+
+Device-Tree bindings for sataphy i2c client driver
+--------------------------------------------------
+
+Required properties:
+compatible: Should be "samsung,exynos-sataphy-i2c"
+- reg: I2C address of the sataphy i2c device.
+
+Example:
+
+	sata_phy_i2c:sata-phy@38 {
+		compatible = "samsung,exynos-sataphy-i2c";
+		reg = <0x38>;
+	};

arch/arm/boot/dts/exynos4.dtsi

@@ -86,6 +86,11 @@
 		reg = <0x10023CE0 0x20>;
 	};
 
+	pd_gps_alive: gps-alive-power-domain@10023D00 {
+		compatible = "samsung,exynos4210-pd";
+		reg = <0x10023D00 0x20>;
+	};
+
 	gic: interrupt-controller@10490000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;

arch/arm/boot/dts/exynos4212.dtsi

@@ -22,16 +22,11 @@
 / {
 	compatible = "samsung,exynos4212";
 
-	gic: interrupt-controller@10490000 {
-		cpu-offset = <0x8000>;
+	combiner: interrupt-controller@10440000 {
+		samsung,combiner-nr = <18>;
 	};
 
-	interrupt-controller@10440000 {
-		samsung,combiner-nr = <18>;
-		interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
-			     <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
-			     <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
-			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
-			     <0 107 0>, <0 108 0>;
+	gic: interrupt-controller@10490000 {
+		cpu-offset = <0x8000>;
 	};
 };

arch/arm/boot/dts/exynos4412-trats2.dts

@@ -106,6 +106,11 @@
 		};
 	};
 
+	adc: adc@126C0000 {
+		vdd-supply = <&ldo3_reg>;
+		status = "okay";
+	};
+
 	i2c@13890000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-slave-addr = <0x10>;
@@ -589,4 +594,20 @@
 			};
 		};
 	};
+
+	thermistor-ap@0 {
+		compatible = "ntc,ncp15wb473";
+		pullup-uv = <1800000>;	 /* VCC_1.8V_AP */
+		pullup-ohm = <100000>;	 /* 100K */
+		pulldown-ohm = <100000>; /* 100K */
+		io-channels = <&adc 1>;  /* AP temperature */
+	};
+
+	thermistor-battery@1 {
+		compatible = "ntc,ncp15wb473";
+		pullup-uv = <1800000>;	 /* VCC_1.8V_AP */
+		pullup-ohm = <100000>;	 /* 100K */
+		pulldown-ohm = <100000>; /* 100K */
+		io-channels = <&adc 2>;  /* Battery temperature */
+	};
 };

arch/arm/boot/dts/exynos4412.dtsi

@@ -22,17 +22,11 @@
 / {
 	compatible = "samsung,exynos4412";
 
-	gic: interrupt-controller@10490000 {
-		cpu-offset = <0x4000>;
-	};
-
-	interrupt-controller@10440000 {
+	combiner: interrupt-controller@10440000 {
 		samsung,combiner-nr = <20>;
-		interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
-			     <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
-			     <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
-			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
-			     <0 107 0>, <0 108 0>, <0 48 0>, <0 42 0>;
 	};
 
+	gic: interrupt-controller@10490000 {
+		cpu-offset = <0x4000>;
+	};
 };

arch/arm/boot/dts/exynos4x12.dtsi

@@ -31,6 +31,12 @@
 		mshc0 = &mshc_0;
 	};
 
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupt-parent = <&combiner>;
+		interrupts = <2 2>, <3 2>, <18 2>, <19 2>;
+	};
+
 	pd_isp: isp-power-domain@10023CA0 {
 		compatible = "samsung,exynos4210-pd";
 		reg = <0x10023CA0 0x20>;
@@ -62,6 +68,14 @@
 		};
 	};
 
+	combiner: interrupt-controller@10440000 {
+		interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
+			     <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
+			     <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
+			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
+			     <0 107 0>, <0 108 0>, <0 48 0>, <0 42 0>;
+	};
+
 	pinctrl_0: pinctrl@11400000 {
 		compatible = "samsung,exynos4x12-pinctrl";
 		reg = <0x11400000 0x1000>;
@@ -80,6 +94,18 @@
 		};
 	};
 
+	adc: adc@126C0000 {
+		compatible = "samsung,exynos-adc-v1";
+		reg = <0x126C0000 0x100>, <0x10020718 0x4>;
+		interrupt-parent = <&combiner>;
+		interrupts = <10 3>;
+		clocks = <&clock CLK_TSADC>;
+		clock-names = "adc";
+		#io-channel-cells = <1>;
+		io-channel-ranges;
+		status = "disabled";
+	};
+
 	pinctrl_2: pinctrl@03860000 {
 		compatible = "samsung,exynos4x12-pinctrl";
 		reg = <0x03860000 0x1000>;

arch/arm/boot/dts/exynos5250-arndale.dts

@@ -374,6 +374,27 @@
 		};
 	};
 
+	i2c@121D0000 {
+		status = "okay";
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <40000>;
+		samsung,i2c-slave-addr = <0x38>;
+
+		sata_phy_i2c:sata-phy@38 {
+			compatible = "samsung,exynos-sataphy-i2c";
+			reg = <0x38>;
+		};
+	};
+
+	sata@122F0000 {
+		status = "okay";
+	};
+
+	sata-phy@12170000 {
+		status = "okay";
+		samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>;
+	};
+
 	mmc_0: mmc@12200000 {
 		status = "okay";
 		num-slots = <1>;

arch/arm/boot/dts/exynos5250-smdk5250.dts

@@ -242,16 +242,12 @@
 		samsung,i2c-slave-addr = <0x38>;
 		status = "okay";
 
-		sata-phy {
-			compatible = "samsung,sata-phy";
+		sata_phy_i2c:sata-phy@38 {
+			compatible = "samsung,exynos-sataphy-i2c";
 			reg = <0x38>;
 		};
 	};
 
-	sata@122F0000 {
-		samsung,sata-freq = <66>;
-	};
-
 	i2c@12C80000 {
 		samsung,i2c-sda-delay = <100>;
 		samsung,i2c-max-bus-freq = <66000>;
@@ -274,6 +270,15 @@
 		};
 	};
 
+	sata@122F0000 {
+		status = "okay";
+	};
+
+	sata-phy@12170000 {
+		status = "okay";
+		samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>;
+	};
+
 	mmc@12200000 {
 		status = "okay";
 		num-slots = <1>;
@@ -310,10 +315,6 @@
 		};
 	};
 
-	spi_0: spi@12d20000 {
-		status = "disabled";
-	};
-
 	spi_1: spi@12d30000 {
 		status = "okay";
 

arch/arm/boot/dts/exynos5250.dtsi

@@ -47,6 +47,7 @@
 		i2c6 = &i2c_6;
 		i2c7 = &i2c_7;
 		i2c8 = &i2c_8;
+		i2c9 = &i2c_9;
 		pinctrl0 = &pinctrl_0;
 		pinctrl1 = &pinctrl_1;
 		pinctrl2 = &pinctrl_2;
@@ -235,16 +236,25 @@
 	};
 
 	sata@122F0000 {
-		compatible = "samsung,exynos5-sata-ahci";
+		compatible = "snps,dwc-ahci";
+		samsung,sata-freq = <66>;
 		reg = <0x122F0000 0x1ff>;
 		interrupts = <0 115 0>;
 		clocks = <&clock CLK_SATA>, <&clock CLK_SCLK_SATA>;
 		clock-names = "sata", "sclk_sata";
+		phys = <&sata_phy>;
+		phy-names = "sata-phy";
+		status = "disabled";
 	};
 
-	sata-phy@12170000 {
-		compatible = "samsung,exynos5-sata-phy";
+	sata_phy: sata-phy@12170000 {
+		compatible = "samsung,exynos5250-sata-phy";
 		reg = <0x12170000 0x1ff>;
+		clocks = <&clock 287>;
+		clock-names = "sata_phyctrl";
+		#phy-cells = <0>;
+		samsung,syscon-phandle = <&pmu_system_controller>;
+		status = "disabled";
 	};
 
 	i2c_0: i2c@12C60000 {
@@ -362,7 +372,7 @@
 		status = "disabled";
 	};
 
-	i2c@121D0000 {
+	i2c_9: i2c@121D0000 {
                 compatible = "samsung,exynos5-sata-phy-i2c";
                 reg = <0x121D0000 0x100>;
                 #address-cells = <1>;
@@ -718,4 +728,12 @@
 		io-channel-ranges;
 		status = "disabled";
 	};
+
+	sss@10830000 {
+		compatible = "samsung,exynos4210-secss";
+		reg = <0x10830000 0x10000>;
+		interrupts = <0 112 0>;
+		clocks = <&clock 348>;
+		clock-names = "secss";
+	};
 };

arch/arm/boot/dts/exynos5420.dtsi

@@ -723,4 +723,13 @@
 		clock-names = "watchdog";
 		samsung,syscon-phandle = <&pmu_system_controller>;
         };
+
+	sss@10830000 {
+		compatible = "samsung,exynos4210-secss";
+		reg = <0x10830000 0x10000>;
+		interrupts = <0 112 0>;
+		clocks = <&clock 471>;
+		clock-names = "secss";
+		samsung,power-domain = <&g2d_pd>;
+	};
 };