Merge branches 'fixes-for-linus', 'generic', 'cavium', 'module.h-fixes', 'next/ath79' and 'next/lantiq' into mips-for-linux-next

Documentation/devicetree/bindings/gpio/gpio-mm-lantiq.txt

@@ -0,0 +1,38 @@
+Lantiq SoC External Bus memory mapped GPIO controller
+
+By attaching hardware latches to the EBU it is possible to create output
+only gpios. This driver configures a special memory address, which when
+written to outputs 16 bit to the latches.
+
+The node describing the memory mapped GPIOs needs to be a child of the node
+describing the "lantiq,localbus".
+
+Required properties:
+- compatible : Should be "lantiq,gpio-mm-lantiq"
+- reg : Address and length of the register set for the device
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- gpio-controller : Marks the device node as a gpio controller.
+
+Optional properties:
+- lantiq,shadow : The default value that we shall assume as already set on the
+  shift register cascade.
+
+Example:
+
+localbus@0 {
+	#address-cells = <2>;
+	#size-cells = <1>;
+	ranges = <0 0 0x0 0x3ffffff /* addrsel0 */
+		1 0 0x4000000 0x4000010>; /* addsel1 */
+	compatible = "lantiq,localbus", "simple-bus";
+
+	gpio_mm0: gpio@4000000 {
+		compatible = "lantiq,gpio-mm";
+		reg = <1 0x0 0x10>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		lantiq,shadow = <0x77f>
+	};
+}

Documentation/devicetree/bindings/gpio/gpio-stp-xway.txt

@@ -0,0 +1,42 @@
+Lantiq SoC Serial To Parallel (STP) GPIO controller
+
+The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a
+peripheral controller used to drive external shift register cascades. At most
+3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem
+to drive the 2 LSBs of the cascade automatically.
+
+
+Required properties:
+- compatible : Should be "lantiq,gpio-stp-xway"
+- reg : Address and length of the register set for the device
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- gpio-controller : Marks the device node as a gpio controller.
+
+Optional properties:
+- lantiq,shadow : The default value that we shall assume as already set on the
+  shift register cascade.
+- lantiq,groups : Set the 3 bit mask to select which of the 3 groups are enabled
+  in the shift register cascade.
+- lantiq,dsl : The dsl core can control the 2 LSBs of the gpio cascade. This 2 bit
+  property can enable this feature.
+- lantiq,phy1 : The gphy1 core can control 3 bits of the gpio cascade.
+- lantiq,phy2 : The gphy2 core can control 3 bits of the gpio cascade.
+- lantiq,rising : use rising instead of falling edge for the shift register
+
+Example:
+
+gpio1: stp@E100BB0 {
+	compatible = "lantiq,gpio-stp-xway";
+	reg = <0xE100BB0 0x40>;
+	#gpio-cells = <2>;
+	gpio-controller;
+
+	lantiq,shadow = <0xffff>;
+	lantiq,groups = <0x7>;
+	lantiq,dsl = <0x3>;
+	lantiq,phy1 = <0x7>;
+	lantiq,phy2 = <0x7>;
+	/* lantiq,rising; */
+};

arch/mips/Kconfig

@@ -228,8 +228,9 @@ config LANTIQ
 	select ARCH_REQUIRE_GPIOLIB
 	select SWAP_IO_SPACE
 	select BOOT_RAW
-	select HAVE_CLK
-	select MIPS_MACHINE
+	select HAVE_MACH_CLKDEV
+	select CLKDEV_LOOKUP
+	select USE_OF
 
 config LASAT
 	bool "LASAT Networks platforms"

arch/mips/alchemy/devboards/db1200.c

@@ -22,6 +22,7 @@
 #include <linux/gpio.h>
 #include <linux/i2c.h>
 #include <linux/init.h>
+#include <linux/module.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/leds.h>

arch/mips/ath79/Kconfig

@@ -26,6 +26,18 @@ config ATH79_MACH_AP81
 	  Say 'Y' here if you want your kernel to support the
 	  Atheros AP81 reference board.
 
+config ATH79_MACH_DB120
+	bool "Atheros DB120 reference board"
+	select SOC_AR934X
+	select ATH79_DEV_GPIO_BUTTONS
+	select ATH79_DEV_LEDS_GPIO
+	select ATH79_DEV_SPI
+	select ATH79_DEV_USB
+	select ATH79_DEV_WMAC
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  Atheros DB120 reference board.
+
 config ATH79_MACH_PB44
 	bool "Atheros PB44 reference board"
 	select SOC_AR71XX
@@ -52,12 +64,14 @@ endmenu
 config SOC_AR71XX
 	select USB_ARCH_HAS_EHCI
 	select USB_ARCH_HAS_OHCI
+	select HW_HAS_PCI
 	def_bool n
 
 config SOC_AR724X
 	select USB_ARCH_HAS_EHCI
 	select USB_ARCH_HAS_OHCI
 	select HW_HAS_PCI
+	select PCI_AR724X if PCI
 	def_bool n
 
 config SOC_AR913X
@@ -68,6 +82,15 @@ config SOC_AR933X
 	select USB_ARCH_HAS_EHCI
 	def_bool n
 
+config SOC_AR934X
+	select USB_ARCH_HAS_EHCI
+	select HW_HAS_PCI
+	select PCI_AR724X if PCI
+	def_bool n
+
+config PCI_AR724X
+	def_bool n
+
 config ATH79_DEV_GPIO_BUTTONS
 	def_bool n
 
@@ -81,7 +104,7 @@ config ATH79_DEV_USB
 	def_bool n
 
 config ATH79_DEV_WMAC
-	depends on (SOC_AR913X || SOC_AR933X)
+	depends on (SOC_AR913X || SOC_AR933X || SOC_AR934X)
 	def_bool n
 
 endif

arch/mips/ath79/Makefile

@@ -11,6 +11,7 @@
 obj-y	:= prom.o setup.o irq.o common.o clock.o gpio.o
 
 obj-$(CONFIG_EARLY_PRINTK)		+= early_printk.o
+obj-$(CONFIG_PCI)			+= pci.o
 
 #
 # Devices
@@ -27,5 +28,6 @@ obj-$(CONFIG_ATH79_DEV_WMAC)		+= dev-wmac.o
 #
 obj-$(CONFIG_ATH79_MACH_AP121)		+= mach-ap121.o
 obj-$(CONFIG_ATH79_MACH_AP81)		+= mach-ap81.o
+obj-$(CONFIG_ATH79_MACH_DB120)		+= mach-db120.o
 obj-$(CONFIG_ATH79_MACH_PB44)		+= mach-pb44.o
 obj-$(CONFIG_ATH79_MACH_UBNT_XM)	+= mach-ubnt-xm.o

arch/mips/ath79/clock.c

@@ -1,8 +1,11 @@
 /*
  *  Atheros AR71XX/AR724X/AR913X common routines
  *
+ *  Copyright (C) 2010-2011 Jaiganesh Narayanan <jnarayanan@atheros.com>
  *  Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
  *
+ *  Parts of this file are based on Atheros' 2.6.15/2.6.31 BSP
+ *
  *  This program is free software; you can redistribute it and/or modify it
  *  under the terms of the GNU General Public License version 2 as published
  *  by the Free Software Foundation.
@@ -163,6 +166,82 @@ static void __init ar933x_clocks_init(void)
 	ath79_uart_clk.rate = ath79_ref_clk.rate;
 }
 
+static void __init ar934x_clocks_init(void)
+{
+	u32 pll, out_div, ref_div, nint, frac, clk_ctrl, postdiv;
+	u32 cpu_pll, ddr_pll;
+	u32 bootstrap;
+
+	bootstrap = ath79_reset_rr(AR934X_RESET_REG_BOOTSTRAP);
+	if (bootstrap &	AR934X_BOOTSTRAP_REF_CLK_40)
+		ath79_ref_clk.rate = 40 * 1000 * 1000;
+	else
+		ath79_ref_clk.rate = 25 * 1000 * 1000;
+
+	pll = ath79_pll_rr(AR934X_PLL_CPU_CONFIG_REG);
+	out_div = (pll >> AR934X_PLL_CPU_CONFIG_OUTDIV_SHIFT) &
+		  AR934X_PLL_CPU_CONFIG_OUTDIV_MASK;
+	ref_div = (pll >> AR934X_PLL_CPU_CONFIG_REFDIV_SHIFT) &
+		  AR934X_PLL_CPU_CONFIG_REFDIV_MASK;
+	nint = (pll >> AR934X_PLL_CPU_CONFIG_NINT_SHIFT) &
+	       AR934X_PLL_CPU_CONFIG_NINT_MASK;
+	frac = (pll >> AR934X_PLL_CPU_CONFIG_NFRAC_SHIFT) &
+	       AR934X_PLL_CPU_CONFIG_NFRAC_MASK;
+
+	cpu_pll = nint * ath79_ref_clk.rate / ref_div;
+	cpu_pll += frac * ath79_ref_clk.rate / (ref_div * (2 << 6));
+	cpu_pll /= (1 << out_div);
+
+	pll = ath79_pll_rr(AR934X_PLL_DDR_CONFIG_REG);
+	out_div = (pll >> AR934X_PLL_DDR_CONFIG_OUTDIV_SHIFT) &
+		  AR934X_PLL_DDR_CONFIG_OUTDIV_MASK;
+	ref_div = (pll >> AR934X_PLL_DDR_CONFIG_REFDIV_SHIFT) &
+		  AR934X_PLL_DDR_CONFIG_REFDIV_MASK;
+	nint = (pll >> AR934X_PLL_DDR_CONFIG_NINT_SHIFT) &
+	       AR934X_PLL_DDR_CONFIG_NINT_MASK;
+	frac = (pll >> AR934X_PLL_DDR_CONFIG_NFRAC_SHIFT) &
+	       AR934X_PLL_DDR_CONFIG_NFRAC_MASK;
+
+	ddr_pll = nint * ath79_ref_clk.rate / ref_div;
+	ddr_pll += frac * ath79_ref_clk.rate / (ref_div * (2 << 10));
+	ddr_pll /= (1 << out_div);
+
+	clk_ctrl = ath79_pll_rr(AR934X_PLL_CPU_DDR_CLK_CTRL_REG);
+
+	postdiv = (clk_ctrl >> AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_POST_DIV_SHIFT) &
+		  AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_POST_DIV_MASK;
+
+	if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_PLL_BYPASS)
+		ath79_cpu_clk.rate = ath79_ref_clk.rate;
+	else if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_CPUCLK_FROM_CPUPLL)
+		ath79_cpu_clk.rate = cpu_pll / (postdiv + 1);
+	else
+		ath79_cpu_clk.rate = ddr_pll / (postdiv + 1);
+
+	postdiv = (clk_ctrl >> AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_POST_DIV_SHIFT) &
+		  AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_POST_DIV_MASK;
+
+	if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_PLL_BYPASS)
+		ath79_ddr_clk.rate = ath79_ref_clk.rate;
+	else if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_DDRCLK_FROM_DDRPLL)
+		ath79_ddr_clk.rate = ddr_pll / (postdiv + 1);
+	else
+		ath79_ddr_clk.rate = cpu_pll / (postdiv + 1);
+
+	postdiv = (clk_ctrl >> AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_POST_DIV_SHIFT) &
+		  AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_POST_DIV_MASK;
+
+	if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_PLL_BYPASS)
+		ath79_ahb_clk.rate = ath79_ref_clk.rate;
+	else if (clk_ctrl & AR934X_PLL_CPU_DDR_CLK_CTRL_AHBCLK_FROM_DDRPLL)
+		ath79_ahb_clk.rate = ddr_pll / (postdiv + 1);
+	else
+		ath79_ahb_clk.rate = cpu_pll / (postdiv + 1);
+
+	ath79_wdt_clk.rate = ath79_ref_clk.rate;
+	ath79_uart_clk.rate = ath79_ref_clk.rate;
+}
+
 void __init ath79_clocks_init(void)
 {
 	if (soc_is_ar71xx())
@@ -173,6 +252,8 @@ void __init ath79_clocks_init(void)
 		ar913x_clocks_init();
 	else if (soc_is_ar933x())
 		ar933x_clocks_init();
+	else if (soc_is_ar934x())
+		ar934x_clocks_init();
 	else
 		BUG();
 

arch/mips/ath79/common.c

@@ -1,9 +1,12 @@
 /*
  *  Atheros AR71XX/AR724X/AR913X common routines
  *
- *  Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2010-2011 Jaiganesh Narayanan <jnarayanan@atheros.com>
+ *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
  *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
  *
+ *  Parts of this file are based on Atheros' 2.6.15/2.6.31 BSP
+ *
  *  This program is free software; you can redistribute it and/or modify it
  *  under the terms of the GNU General Public License version 2 as published
  *  by the Free Software Foundation.
@@ -67,6 +70,8 @@ void ath79_device_reset_set(u32 mask)
 		reg = AR913X_RESET_REG_RESET_MODULE;
 	else if (soc_is_ar933x())
 		reg = AR933X_RESET_REG_RESET_MODULE;
+	else if (soc_is_ar934x())
+		reg = AR934X_RESET_REG_RESET_MODULE;
 	else
 		BUG();
 
@@ -91,6 +96,8 @@ void ath79_device_reset_clear(u32 mask)
 		reg = AR913X_RESET_REG_RESET_MODULE;
 	else if (soc_is_ar933x())
 		reg = AR933X_RESET_REG_RESET_MODULE;
+	else if (soc_is_ar934x())
+		reg = AR934X_RESET_REG_RESET_MODULE;
 	else
 		BUG();
 

arch/mips/ath79/dev-common.c

@@ -89,7 +89,8 @@ void __init ath79_register_uart(void)
 
 	if (soc_is_ar71xx() ||
 	    soc_is_ar724x() ||
-	    soc_is_ar913x()) {
+	    soc_is_ar913x() ||
+	    soc_is_ar934x()) {
 		ath79_uart_data[0].uartclk = clk_get_rate(clk);
 		platform_device_register(&ath79_uart_device);
 	} else if (soc_is_ar933x()) {

arch/mips/ath79/dev-gpio-buttons.c

@@ -25,12 +25,10 @@ void __init ath79_register_gpio_keys_polled(int id,
 	struct gpio_keys_button *p;
 	int err;
 
-	p = kmalloc(nbuttons * sizeof(*p), GFP_KERNEL);
+	p = kmemdup(buttons, nbuttons * sizeof(*p), GFP_KERNEL);
 	if (!p)
 		return;
 
-	memcpy(p, buttons, nbuttons * sizeof(*p));
-
 	pdev = platform_device_alloc("gpio-keys-polled", id);
 	if (!pdev)
 		goto err_free_buttons;

arch/mips/ath79/dev-leds-gpio.c

@@ -24,12 +24,10 @@ void __init ath79_register_leds_gpio(int id,
 	struct gpio_led *p;
 	int err;
 
-	p = kmalloc(num_leds * sizeof(*p), GFP_KERNEL);
+	p = kmemdup(leds, num_leds * sizeof(*p), GFP_KERNEL);
 	if (!p)
 		return;
 
-	memcpy(p, leds, num_leds * sizeof(*p));
-
 	pdev = platform_device_alloc("leds-gpio", id);
 	if (!pdev)
 		goto err_free_leds;

arch/mips/ath79/dev-wmac.c

@@ -1,9 +1,12 @@
 /*
  *  Atheros AR913X/AR933X SoC built-in WMAC device support
  *
+ *  Copyright (C) 2010-2011 Jaiganesh Narayanan <jnarayanan@atheros.com>
  *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
  *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
  *
+ *  Parts of this file are based on Atheros 2.6.15/2.6.31 BSP
+ *
  *  This program is free software; you can redistribute it and/or modify it
  *  under the terms of the GNU General Public License version 2 as published
  *  by the Free Software Foundation.
@@ -26,8 +29,7 @@ static struct resource ath79_wmac_resources[] = {
 		/* .start and .end fields are filled dynamically */
 		.flags	= IORESOURCE_MEM,
 	}, {
-		.start	= ATH79_CPU_IRQ_IP2,
-		.end	= ATH79_CPU_IRQ_IP2,
+		/* .start and .end fields are filled dynamically */
 		.flags	= IORESOURCE_IRQ,
 	},
 };
@@ -53,6 +55,8 @@ static void __init ar913x_wmac_setup(void)
 
 	ath79_wmac_resources[0].start = AR913X_WMAC_BASE;
 	ath79_wmac_resources[0].end = AR913X_WMAC_BASE + AR913X_WMAC_SIZE - 1;
+	ath79_wmac_resources[1].start = ATH79_CPU_IRQ_IP2;
+	ath79_wmac_resources[1].end = ATH79_CPU_IRQ_IP2;
 }
 
 
@@ -79,6 +83,8 @@ static void __init ar933x_wmac_setup(void)
 
 	ath79_wmac_resources[0].start = AR933X_WMAC_BASE;
 	ath79_wmac_resources[0].end = AR933X_WMAC_BASE + AR933X_WMAC_SIZE - 1;
+	ath79_wmac_resources[1].start = ATH79_CPU_IRQ_IP2;
+	ath79_wmac_resources[1].end = ATH79_CPU_IRQ_IP2;
 
 	t = ath79_reset_rr(AR933X_RESET_REG_BOOTSTRAP);
 	if (t & AR933X_BOOTSTRAP_REF_CLK_40)
@@ -92,12 +98,32 @@ static void __init ar933x_wmac_setup(void)
 	ath79_wmac_data.external_reset = ar933x_wmac_reset;
 }
 
+static void ar934x_wmac_setup(void)
+{
+	u32 t;
+
+	ath79_wmac_device.name = "ar934x_wmac";
+
+	ath79_wmac_resources[0].start = AR934X_WMAC_BASE;
+	ath79_wmac_resources[0].end = AR934X_WMAC_BASE + AR934X_WMAC_SIZE - 1;
+	ath79_wmac_resources[1].start = ATH79_IP2_IRQ(1);
+	ath79_wmac_resources[1].start = ATH79_IP2_IRQ(1);
+
+	t = ath79_reset_rr(AR934X_RESET_REG_BOOTSTRAP);
+	if (t & AR934X_BOOTSTRAP_REF_CLK_40)
+		ath79_wmac_data.is_clk_25mhz = false;
+	else
+		ath79_wmac_data.is_clk_25mhz = true;
+}
+
 void __init ath79_register_wmac(u8 *cal_data)
 {
 	if (soc_is_ar913x())
 		ar913x_wmac_setup();
 	else if (soc_is_ar933x())
 		ar933x_wmac_setup();
+	else if (soc_is_ar934x())
+		ar934x_wmac_setup();
 	else
 		BUG();
 

arch/mips/ath79/early_printk.c

@@ -71,6 +71,9 @@ static void prom_putchar_init(void)
 	case REV_ID_MAJOR_AR7241:
 	case REV_ID_MAJOR_AR7242:
 	case REV_ID_MAJOR_AR913X:
+	case REV_ID_MAJOR_AR9341:
+	case REV_ID_MAJOR_AR9342:
+	case REV_ID_MAJOR_AR9344:
 		_prom_putchar = prom_putchar_ar71xx;
 		break;
 

arch/mips/ath79/gpio.c

@@ -1,9 +1,12 @@
 /*
  *  Atheros AR71XX/AR724X/AR913X GPIO API support
  *
- *  Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2010-2011 Jaiganesh Narayanan <jnarayanan@atheros.com>
+ *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
  *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
  *
+ *  Parts of this file are based on Atheros' 2.6.15/2.6.31 BSP
+ *
  *  This program is free software; you can redistribute it and/or modify it
  *  under the terms of the GNU General Public License version 2 as published
  *  by the Free Software Foundation.
@@ -89,6 +92,42 @@ static int ath79_gpio_direction_output(struct gpio_chip *chip,
 	return 0;
 }
 
+static int ar934x_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	void __iomem *base = ath79_gpio_base;
+	unsigned long flags;
+
+	spin_lock_irqsave(&ath79_gpio_lock, flags);
+
+	__raw_writel(__raw_readl(base + AR71XX_GPIO_REG_OE) | (1 << offset),
+		     base + AR71XX_GPIO_REG_OE);
+
+	spin_unlock_irqrestore(&ath79_gpio_lock, flags);
+
+	return 0;
+}
+
+static int ar934x_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
+					int value)
+{
+	void __iomem *base = ath79_gpio_base;
+	unsigned long flags;
+
+	spin_lock_irqsave(&ath79_gpio_lock, flags);
+
+	if (value)
+		__raw_writel(1 << offset, base + AR71XX_GPIO_REG_SET);
+	else
+		__raw_writel(1 << offset, base + AR71XX_GPIO_REG_CLEAR);
+
+	__raw_writel(__raw_readl(base + AR71XX_GPIO_REG_OE) & ~(1 << offset),
+		     base + AR71XX_GPIO_REG_OE);
+
+	spin_unlock_irqrestore(&ath79_gpio_lock, flags);
+
+	return 0;
+}
+
 static struct gpio_chip ath79_gpio_chip = {
 	.label			= "ath79",
 	.get			= ath79_gpio_get_value,
@@ -155,11 +194,17 @@ void __init ath79_gpio_init(void)
 		ath79_gpio_count = AR913X_GPIO_COUNT;
 	else if (soc_is_ar933x())
 		ath79_gpio_count = AR933X_GPIO_COUNT;
+	else if (soc_is_ar934x())
+		ath79_gpio_count = AR934X_GPIO_COUNT;
 	else
 		BUG();
 
 	ath79_gpio_base = ioremap_nocache(AR71XX_GPIO_BASE, AR71XX_GPIO_SIZE);
 	ath79_gpio_chip.ngpio = ath79_gpio_count;
+	if (soc_is_ar934x()) {
+		ath79_gpio_chip.direction_input = ar934x_gpio_direction_input;
+		ath79_gpio_chip.direction_output = ar934x_gpio_direction_output;
+	}
 
 	err = gpiochip_add(&ath79_gpio_chip);
 	if (err)

arch/mips/ath79/irq.c

@@ -1,10 +1,11 @@
 /*
  *  Atheros AR71xx/AR724x/AR913x specific interrupt handling
  *
- *  Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2010-2011 Jaiganesh Narayanan <jnarayanan@atheros.com>
+ *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
  *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
  *
- *  Parts of this file are based on Atheros' 2.6.15 BSP
+ *  Parts of this file are based on Atheros' 2.6.15/2.6.31 BSP
  *
  *  This program is free software; you can redistribute it and/or modify it
  *  under the terms of the GNU General Public License version 2 as published
@@ -23,8 +24,8 @@
 #include <asm/mach-ath79/ar71xx_regs.h>
 #include "common.h"
 
-static unsigned int ath79_ip2_flush_reg;
-static unsigned int ath79_ip3_flush_reg;
+static void (*ath79_ip2_handler)(void);
+static void (*ath79_ip3_handler)(void);
 
 static void ath79_misc_irq_handler(unsigned int irq, struct irq_desc *desc)
 {
@@ -129,7 +130,7 @@ static void __init ath79_misc_irq_init(void)
 
 	if (soc_is_ar71xx() || soc_is_ar913x())
 		ath79_misc_irq_chip.irq_mask_ack = ar71xx_misc_irq_mask;
-	else if (soc_is_ar724x() || soc_is_ar933x())
+	else if (soc_is_ar724x() || soc_is_ar933x() || soc_is_ar934x())
 		ath79_misc_irq_chip.irq_ack = ar724x_misc_irq_ack;
 	else
 		BUG();
@@ -143,6 +144,39 @@ static void __init ath79_misc_irq_init(void)
 	irq_set_chained_handler(ATH79_CPU_IRQ_MISC, ath79_misc_irq_handler);
 }
 
+static void ar934x_ip2_irq_dispatch(unsigned int irq, struct irq_desc *desc)
+{
+	u32 status;
+
+	disable_irq_nosync(irq);
+
+	status = ath79_reset_rr(AR934X_RESET_REG_PCIE_WMAC_INT_STATUS);
+
+	if (status & AR934X_PCIE_WMAC_INT_PCIE_ALL) {
+		ath79_ddr_wb_flush(AR934X_DDR_REG_FLUSH_PCIE);
+		generic_handle_irq(ATH79_IP2_IRQ(0));
+	} else if (status & AR934X_PCIE_WMAC_INT_WMAC_ALL) {
+		ath79_ddr_wb_flush(AR934X_DDR_REG_FLUSH_WMAC);
+		generic_handle_irq(ATH79_IP2_IRQ(1));
+	} else {
+		spurious_interrupt();
+	}
+
+	enable_irq(irq);
+}
+
+static void ar934x_ip2_irq_init(void)
+{
+	int i;
+
+	for (i = ATH79_IP2_IRQ_BASE;
+	     i < ATH79_IP2_IRQ_BASE + ATH79_IP2_IRQ_COUNT; i++)
+		irq_set_chip_and_handler(i, &dummy_irq_chip,
+					 handle_level_irq);
+
+	irq_set_chained_handler(ATH79_CPU_IRQ_IP2, ar934x_ip2_irq_dispatch);
+}
+
 asmlinkage void plat_irq_dispatch(void)
 {
 	unsigned long pending;
@@ -152,10 +186,8 @@ asmlinkage void plat_irq_dispatch(void)
 	if (pending & STATUSF_IP7)
 		do_IRQ(ATH79_CPU_IRQ_TIMER);
 
-	else if (pending & STATUSF_IP2) {
-		ath79_ddr_wb_flush(ath79_ip2_flush_reg);
-		do_IRQ(ATH79_CPU_IRQ_IP2);
-	}
+	else if (pending & STATUSF_IP2)
+		ath79_ip2_handler();
 
 	else if (pending & STATUSF_IP4)
 		do_IRQ(ATH79_CPU_IRQ_GE0);
@@ -163,10 +195,8 @@ asmlinkage void plat_irq_dispatch(void)
 	else if (pending & STATUSF_IP5)
 		do_IRQ(ATH79_CPU_IRQ_GE1);
 
-	else if (pending & STATUSF_IP3) {
-		ath79_ddr_wb_flush(ath79_ip3_flush_reg);
-		do_IRQ(ATH79_CPU_IRQ_USB);
-	}
+	else if (pending & STATUSF_IP3)
+		ath79_ip3_handler();
 
 	else if (pending & STATUSF_IP6)
 		do_IRQ(ATH79_CPU_IRQ_MISC);
@@ -175,24 +205,97 @@ asmlinkage void plat_irq_dispatch(void)
 		spurious_interrupt();
 }
 
+/*
+ * The IP2/IP3 lines are tied to a PCI/WMAC/USB device. Drivers for
+ * these devices typically allocate coherent DMA memory, however the
+ * DMA controller may still have some unsynchronized data in the FIFO.
+ * Issue a flush in the handlers to ensure that the driver sees
+ * the update.
+ */
+static void ar71xx_ip2_handler(void)
+{
+	ath79_ddr_wb_flush(AR71XX_DDR_REG_FLUSH_PCI);
+	do_IRQ(ATH79_CPU_IRQ_IP2);
+}
+
+static void ar724x_ip2_handler(void)
+{
+	ath79_ddr_wb_flush(AR724X_DDR_REG_FLUSH_PCIE);
+	do_IRQ(ATH79_CPU_IRQ_IP2);
+}
+
+static void ar913x_ip2_handler(void)
+{
+	ath79_ddr_wb_flush(AR913X_DDR_REG_FLUSH_WMAC);
+	do_IRQ(ATH79_CPU_IRQ_IP2);
+}
+
+static void ar933x_ip2_handler(void)
+{
+	ath79_ddr_wb_flush(AR933X_DDR_REG_FLUSH_WMAC);
+	do_IRQ(ATH79_CPU_IRQ_IP2);
+}
+
+static void ar934x_ip2_handler(void)
+{
+	do_IRQ(ATH79_CPU_IRQ_IP2);
+}
+
+static void ar71xx_ip3_handler(void)
+{
+	ath79_ddr_wb_flush(AR71XX_DDR_REG_FLUSH_USB);
+	do_IRQ(ATH79_CPU_IRQ_USB);
+}
+
+static void ar724x_ip3_handler(void)
+{
+	ath79_ddr_wb_flush(AR724X_DDR_REG_FLUSH_USB);
+	do_IRQ(ATH79_CPU_IRQ_USB);
+}
+
+static void ar913x_ip3_handler(void)
+{
+	ath79_ddr_wb_flush(AR913X_DDR_REG_FLUSH_USB);
+	do_IRQ(ATH79_CPU_IRQ_USB);
+}
+
+static void ar933x_ip3_handler(void)
+{
+	ath79_ddr_wb_flush(AR933X_DDR_REG_FLUSH_USB);
+	do_IRQ(ATH79_CPU_IRQ_USB);
+}
+
+static void ar934x_ip3_handler(void)
+{
+	ath79_ddr_wb_flush(AR934X_DDR_REG_FLUSH_USB);
+	do_IRQ(ATH79_CPU_IRQ_USB);
+}
+
 void __init arch_init_irq(void)
 {
 	if (soc_is_ar71xx()) {
-		ath79_ip2_flush_reg = AR71XX_DDR_REG_FLUSH_PCI;
-		ath79_ip3_flush_reg = AR71XX_DDR_REG_FLUSH_USB;
+		ath79_ip2_handler = ar71xx_ip2_handler;
+		ath79_ip3_handler = ar71xx_ip3_handler;
 	} else if (soc_is_ar724x()) {
-		ath79_ip2_flush_reg = AR724X_DDR_REG_FLUSH_PCIE;
-		ath79_ip3_flush_reg = AR724X_DDR_REG_FLUSH_USB;
+		ath79_ip2_handler = ar724x_ip2_handler;
+		ath79_ip3_handler = ar724x_ip3_handler;
 	} else if (soc_is_ar913x()) {
-		ath79_ip2_flush_reg = AR913X_DDR_REG_FLUSH_WMAC;
-		ath79_ip3_flush_reg = AR913X_DDR_REG_FLUSH_USB;
+		ath79_ip2_handler = ar913x_ip2_handler;
+		ath79_ip3_handler = ar913x_ip3_handler;
 	} else if (soc_is_ar933x()) {
-		ath79_ip2_flush_reg = AR933X_DDR_REG_FLUSH_WMAC;
-		ath79_ip3_flush_reg = AR933X_DDR_REG_FLUSH_USB;
-	} else
+		ath79_ip2_handler = ar933x_ip2_handler;
+		ath79_ip3_handler = ar933x_ip3_handler;
+	} else if (soc_is_ar934x()) {
+		ath79_ip2_handler = ar934x_ip2_handler;
+		ath79_ip3_handler = ar934x_ip3_handler;
+	} else {
 		BUG();
+	}
 
 	cp0_perfcount_irq = ATH79_MISC_IRQ_PERFC;
 	mips_cpu_irq_init();
 	ath79_misc_irq_init();
+
+	if (soc_is_ar934x())
+		ar934x_ip2_irq_init();
 }

arch/mips/ath79/mach-db120.c

@@ -0,0 +1,134 @@
+/*
+ * Atheros DB120 reference board support
+ *
+ * Copyright (c) 2011 Qualcomm Atheros
+ * Copyright (c) 2011 Gabor Juhos <juhosg@openwrt.org>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include <linux/pci.h>
+#include <linux/ath9k_platform.h>
+
+#include "machtypes.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-spi.h"
+#include "dev-wmac.h"
+#include "pci.h"
+
+#define DB120_GPIO_LED_WLAN_5G		12
+#define DB120_GPIO_LED_WLAN_2G		13
+#define DB120_GPIO_LED_STATUS		14
+#define DB120_GPIO_LED_WPS		15
+
+#define DB120_GPIO_BTN_WPS		16
+
+#define DB120_KEYS_POLL_INTERVAL	20	/* msecs */
+#define DB120_KEYS_DEBOUNCE_INTERVAL	(3 * DB120_KEYS_POLL_INTERVAL)
+
+#define DB120_WMAC_CALDATA_OFFSET 0x1000
+#define DB120_PCIE_CALDATA_OFFSET 0x5000
+
+static struct gpio_led db120_leds_gpio[] __initdata = {
+	{
+		.name		= "db120:green:status",
+		.gpio		= DB120_GPIO_LED_STATUS,
+		.active_low	= 1,
+	},
+	{
+		.name		= "db120:green:wps",
+		.gpio		= DB120_GPIO_LED_WPS,
+		.active_low	= 1,
+	},
+	{
+		.name		= "db120:green:wlan-5g",
+		.gpio		= DB120_GPIO_LED_WLAN_5G,
+		.active_low	= 1,
+	},
+	{
+		.name		= "db120:green:wlan-2g",
+		.gpio		= DB120_GPIO_LED_WLAN_2G,
+		.active_low	= 1,
+	},
+};
+
+static struct gpio_keys_button db120_gpio_keys[] __initdata = {
+	{
+		.desc		= "WPS button",
+		.type		= EV_KEY,
+		.code		= KEY_WPS_BUTTON,
+		.debounce_interval = DB120_KEYS_DEBOUNCE_INTERVAL,
+		.gpio		= DB120_GPIO_BTN_WPS,
+		.active_low	= 1,
+	},
+};
+
+static struct spi_board_info db120_spi_info[] = {
+	{
+		.bus_num	= 0,
+		.chip_select	= 0,
+		.max_speed_hz	= 25000000,
+		.modalias	= "s25sl064a",
+	}
+};
+
+static struct ath79_spi_platform_data db120_spi_data = {
+	.bus_num	= 0,
+	.num_chipselect	= 1,
+};
+
+#ifdef CONFIG_PCI
+static struct ath9k_platform_data db120_ath9k_data;
+
+static int db120_pci_plat_dev_init(struct pci_dev *dev)
+{
+	switch (PCI_SLOT(dev->devfn)) {
+	case 0:
+		dev->dev.platform_data = &db120_ath9k_data;
+		break;
+	}
+
+	return 0;
+}
+
+static void __init db120_pci_init(u8 *eeprom)
+{
+	memcpy(db120_ath9k_data.eeprom_data, eeprom,
+	       sizeof(db120_ath9k_data.eeprom_data));
+
+	ath79_pci_set_plat_dev_init(db120_pci_plat_dev_init);
+	ath79_register_pci();
+}
+#else
+static inline void db120_pci_init(void) {}
+#endif /* CONFIG_PCI */
+
+static void __init db120_setup(void)
+{
+	u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
+
+	ath79_register_leds_gpio(-1, ARRAY_SIZE(db120_leds_gpio),
+				 db120_leds_gpio);
+	ath79_register_gpio_keys_polled(-1, DB120_KEYS_POLL_INTERVAL,
+					ARRAY_SIZE(db120_gpio_keys),
+					db120_gpio_keys);
+	ath79_register_spi(&db120_spi_data, db120_spi_info,
+			   ARRAY_SIZE(db120_spi_info));
+	ath79_register_wmac(art + DB120_WMAC_CALDATA_OFFSET);
+	db120_pci_init(art + DB120_PCIE_CALDATA_OFFSET);
+}
+
+MIPS_MACHINE(ATH79_MACH_DB120, "DB120", "Atheros DB120 reference board",
+	     db120_setup);

arch/mips/ath79/mach-pb44.c

@@ -19,6 +19,7 @@
 #include "dev-leds-gpio.h"
 #include "dev-spi.h"
 #include "dev-usb.h"
+#include "pci.h"
 
 #define PB44_GPIO_I2C_SCL	0
 #define PB44_GPIO_I2C_SDA	1
@@ -114,6 +115,7 @@ static void __init pb44_init(void)
 	ath79_register_spi(&pb44_spi_data, pb44_spi_info,
 			   ARRAY_SIZE(pb44_spi_info));
 	ath79_register_usb();
+	ath79_register_pci();
 }
 
 MIPS_MACHINE(ATH79_MACH_PB44, "PB44", "Atheros PB44 reference board",

arch/mips/ath79/mach-ubnt-xm.c

@@ -12,16 +12,15 @@
 
 #include <linux/init.h>
 #include <linux/pci.h>
-
-#ifdef CONFIG_PCI
 #include <linux/ath9k_platform.h>
-#include <asm/mach-ath79/pci-ath724x.h>
-#endif /* CONFIG_PCI */
+
+#include <asm/mach-ath79/irq.h>
 
 #include "machtypes.h"
 #include "dev-gpio-buttons.h"
 #include "dev-leds-gpio.h"
 #include "dev-spi.h"
+#include "pci.h"
 
 #define UBNT_XM_GPIO_LED_L1		0
 #define UBNT_XM_GPIO_LED_L2		1
@@ -33,7 +32,6 @@
 #define UBNT_XM_KEYS_POLL_INTERVAL	20
 #define UBNT_XM_KEYS_DEBOUNCE_INTERVAL	(3 * UBNT_XM_KEYS_POLL_INTERVAL)
 
-#define UBNT_XM_PCI_IRQ			48
 #define UBNT_XM_EEPROM_ADDR		(u8 *) KSEG1ADDR(0x1fff1000)
 
 static struct gpio_led ubnt_xm_leds_gpio[] __initdata = {
@@ -84,12 +82,27 @@ static struct ath79_spi_platform_data ubnt_xm_spi_data = {
 #ifdef CONFIG_PCI
 static struct ath9k_platform_data ubnt_xm_eeprom_data;
 
-static struct ath724x_pci_data ubnt_xm_pci_data[] = {
-	{
-		.irq	= UBNT_XM_PCI_IRQ,
-		.pdata	= &ubnt_xm_eeprom_data,
-	},
-};
+static int ubnt_xm_pci_plat_dev_init(struct pci_dev *dev)
+{
+	switch (PCI_SLOT(dev->devfn)) {
+	case 0:
+		dev->dev.platform_data = &ubnt_xm_eeprom_data;
+		break;
+	}
+
+	return 0;
+}
+
+static void __init ubnt_xm_pci_init(void)
+{
+	memcpy(ubnt_xm_eeprom_data.eeprom_data, UBNT_XM_EEPROM_ADDR,
+	       sizeof(ubnt_xm_eeprom_data.eeprom_data));
+
+	ath79_pci_set_plat_dev_init(ubnt_xm_pci_plat_dev_init);
+	ath79_register_pci();
+}
+#else
+static inline void ubnt_xm_pci_init(void) {}
 #endif /* CONFIG_PCI */
 
 static void __init ubnt_xm_init(void)
@@ -104,13 +117,7 @@ static void __init ubnt_xm_init(void)
 	ath79_register_spi(&ubnt_xm_spi_data, ubnt_xm_spi_info,
 			   ARRAY_SIZE(ubnt_xm_spi_info));
 
-#ifdef CONFIG_PCI
-	memcpy(ubnt_xm_eeprom_data.eeprom_data, UBNT_XM_EEPROM_ADDR,
-	       sizeof(ubnt_xm_eeprom_data.eeprom_data));
-
-	ath724x_pci_add_data(ubnt_xm_pci_data, ARRAY_SIZE(ubnt_xm_pci_data));
-#endif /* CONFIG_PCI */
-
+	ubnt_xm_pci_init();
 }
 
 MIPS_MACHINE(ATH79_MACH_UBNT_XM,

arch/mips/ath79/machtypes.h

@@ -18,6 +18,7 @@ enum ath79_mach_type {
 	ATH79_MACH_GENERIC = 0,
 	ATH79_MACH_AP121,		/* Atheros AP121 reference board */
 	ATH79_MACH_AP81,		/* Atheros AP81 reference board */
+	ATH79_MACH_DB120,		/* Atheros DB120 reference board */
 	ATH79_MACH_PB44,		/* Atheros PB44 reference board */
 	ATH79_MACH_UBNT_XM,		/* Ubiquiti Networks XM board rev 1.0 */
 };

arch/mips/ath79/pci.c

@@ -0,0 +1,130 @@
+/*
+ *  Atheros AR71XX/AR724X specific PCI setup code
+ *
+ *  Copyright (C) 2011 René Bolldorf <xsecute@googlemail.com>
+ *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *  Parts of this file are based on Atheros' 2.6.15 BSP
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/pci.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/irq.h>
+#include <asm/mach-ath79/pci.h>
+#include "pci.h"
+
+static int (*ath79_pci_plat_dev_init)(struct pci_dev *dev);
+static const struct ath79_pci_irq *ath79_pci_irq_map __initdata;
+static unsigned ath79_pci_nr_irqs __initdata;
+
+static const struct ath79_pci_irq ar71xx_pci_irq_map[] __initconst = {
+	{
+		.slot	= 17,
+		.pin	= 1,
+		.irq	= ATH79_PCI_IRQ(0),
+	}, {
+		.slot	= 18,
+		.pin	= 1,
+		.irq	= ATH79_PCI_IRQ(1),
+	}, {
+		.slot	= 19,
+		.pin	= 1,
+		.irq	= ATH79_PCI_IRQ(2),
+	}
+};
+
+static const struct ath79_pci_irq ar724x_pci_irq_map[] __initconst = {
+	{
+		.slot	= 0,
+		.pin	= 1,
+		.irq	= ATH79_PCI_IRQ(0),
+	}
+};
+
+int __init pcibios_map_irq(const struct pci_dev *dev, uint8_t slot, uint8_t pin)
+{
+	int irq = -1;
+	int i;
+
+	if (ath79_pci_nr_irqs == 0 ||
+	    ath79_pci_irq_map == NULL) {
+		if (soc_is_ar71xx()) {
+			ath79_pci_irq_map = ar71xx_pci_irq_map;
+			ath79_pci_nr_irqs = ARRAY_SIZE(ar71xx_pci_irq_map);
+		} else if (soc_is_ar724x() ||
+			   soc_is_ar9342() ||
+			   soc_is_ar9344()) {
+			ath79_pci_irq_map = ar724x_pci_irq_map;
+			ath79_pci_nr_irqs = ARRAY_SIZE(ar724x_pci_irq_map);
+		} else {
+			pr_crit("pci %s: invalid irq map\n",
+				pci_name((struct pci_dev *) dev));
+			return irq;
+		}
+	}
+
+	for (i = 0; i < ath79_pci_nr_irqs; i++) {
+		const struct ath79_pci_irq *entry;
+
+		entry = &ath79_pci_irq_map[i];
+		if (entry->slot == slot && entry->pin == pin) {
+			irq = entry->irq;
+			break;
+		}
+	}
+
+	if (irq < 0)
+		pr_crit("pci %s: no irq found for pin %u\n",
+			pci_name((struct pci_dev *) dev), pin);
+	else
+		pr_info("pci %s: using irq %d for pin %u\n",
+			pci_name((struct pci_dev *) dev), irq, pin);
+
+	return irq;
+}
+
+int pcibios_plat_dev_init(struct pci_dev *dev)
+{
+	if (ath79_pci_plat_dev_init)
+		return ath79_pci_plat_dev_init(dev);
+
+	return 0;
+}
+
+void __init ath79_pci_set_irq_map(unsigned nr_irqs,
+				  const struct ath79_pci_irq *map)
+{
+	ath79_pci_nr_irqs = nr_irqs;
+	ath79_pci_irq_map = map;
+}
+
+void __init ath79_pci_set_plat_dev_init(int (*func)(struct pci_dev *dev))
+{
+	ath79_pci_plat_dev_init = func;
+}
+
+int __init ath79_register_pci(void)
+{
+	if (soc_is_ar71xx())
+		return ar71xx_pcibios_init();
+
+	if (soc_is_ar724x())
+		return ar724x_pcibios_init(ATH79_CPU_IRQ_IP2);
+
+	if (soc_is_ar9342() || soc_is_ar9344()) {
+		u32 bootstrap;
+
+		bootstrap = ath79_reset_rr(AR934X_RESET_REG_BOOTSTRAP);
+		if (bootstrap & AR934X_BOOTSTRAP_PCIE_RC)
+			return ar724x_pcibios_init(ATH79_IP2_IRQ(0));
+	}
+
+	return -ENODEV;
+}

arch/mips/ath79/pci.h

@@ -0,0 +1,34 @@
+/*
+ *  Atheros AR71XX/AR724X PCI support
+ *
+ *  Copyright (C) 2011 René Bolldorf <xsecute@googlemail.com>
+ *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+
+#ifndef _ATH79_PCI_H
+#define _ATH79_PCI_H
+
+struct ath79_pci_irq {
+	u8	slot;
+	u8	pin;
+	int	irq;
+};
+
+#ifdef CONFIG_PCI
+void ath79_pci_set_irq_map(unsigned nr_irqs, const struct ath79_pci_irq *map);
+void ath79_pci_set_plat_dev_init(int (*func)(struct pci_dev *dev));
+int ath79_register_pci(void);
+#else
+static inline void
+ath79_pci_set_irq_map(unsigned nr_irqs, const struct ath79_pci_irq *map) {}
+static inline void
+ath79_pci_set_plat_dev_init(int (*func)(struct pci_dev *)) {}
+static inline int ath79_register_pci(void) { return 0; }
+#endif
+
+#endif /* _ATH79_PCI_H */

arch/mips/ath79/setup.c

@@ -1,10 +1,11 @@
 /*
  *  Atheros AR71XX/AR724X/AR913X specific setup
  *
+ *  Copyright (C) 2010-2011 Jaiganesh Narayanan <jnarayanan@atheros.com>
  *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
  *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
  *
- *  Parts of this file are based on Atheros' 2.6.15 BSP
+ *  Parts of this file are based on Atheros' 2.6.15/2.6.31 BSP
  *
  *  This program is free software; you can redistribute it and/or modify it
  *  under the terms of the GNU General Public License version 2 as published
@@ -116,18 +117,6 @@ static void __init ath79_detect_sys_type(void)
 		rev = id & AR724X_REV_ID_REVISION_MASK;
 		break;
 
-	case REV_ID_MAJOR_AR9330:
-		ath79_soc = ATH79_SOC_AR9330;
-		chip = "9330";
-		rev = id & AR933X_REV_ID_REVISION_MASK;
-		break;
-
-	case REV_ID_MAJOR_AR9331:
-		ath79_soc = ATH79_SOC_AR9331;
-		chip = "9331";
-		rev = id & AR933X_REV_ID_REVISION_MASK;
-		break;
-
 	case REV_ID_MAJOR_AR913X:
 		minor = id & AR913X_REV_ID_MINOR_MASK;
 		rev = id >> AR913X_REV_ID_REVISION_SHIFT;
@@ -145,6 +134,36 @@ static void __init ath79_detect_sys_type(void)
 		}
 		break;
 
+	case REV_ID_MAJOR_AR9330:
+		ath79_soc = ATH79_SOC_AR9330;
+		chip = "9330";
+		rev = id & AR933X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_AR9331:
+		ath79_soc = ATH79_SOC_AR9331;
+		chip = "9331";
+		rev = id & AR933X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_AR9341:
+		ath79_soc = ATH79_SOC_AR9341;
+		chip = "9341";
+		rev = id & AR934X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_AR9342:
+		ath79_soc = ATH79_SOC_AR9342;
+		chip = "9342";
+		rev = id & AR934X_REV_ID_REVISION_MASK;
+		break;
+
+	case REV_ID_MAJOR_AR9344:
+		ath79_soc = ATH79_SOC_AR9344;
+		chip = "9344";
+		rev = id & AR934X_REV_ID_REVISION_MASK;
+		break;
+
 	default:
 		panic("ath79: unknown SoC, id:0x%08x", id);
 	}

arch/mips/bcm63xx/boards/Makefile

@@ -1,3 +1 @@
 obj-$(CONFIG_BOARD_BCM963XX)		+= board_bcm963xx.o
-
-ccflags-y := -Werror

arch/mips/cavium-octeon/setup.c

@@ -9,6 +9,7 @@
 #include <linux/init.h>
 #include <linux/console.h>
 #include <linux/delay.h>
+#include <linux/export.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/serial.h>

arch/mips/cavium-octeon/smp.c

@@ -257,8 +257,6 @@ DEFINE_PER_CPU(int, cpu_state);
 
 extern void fixup_irqs(void);
 
-static DEFINE_SPINLOCK(smp_reserve_lock);
-
 static int octeon_cpu_disable(void)
 {
 	unsigned int cpu = smp_processor_id();
@@ -266,8 +264,6 @@ static int octeon_cpu_disable(void)
 	if (cpu == 0)
 		return -EBUSY;
 
-	spin_lock(&smp_reserve_lock);
-
 	set_cpu_online(cpu, false);
 	cpu_clear(cpu, cpu_callin_map);
 	local_irq_disable();
@@ -277,8 +273,6 @@ static int octeon_cpu_disable(void)
 	flush_cache_all();
 	local_flush_tlb_all();
 
-	spin_unlock(&smp_reserve_lock);
-
 	return 0;
 }
 

arch/mips/fw/arc/Makefile

@@ -8,5 +8,3 @@ lib-y				+= cmdline.o env.o file.o identify.o init.o \
 lib-$(CONFIG_ARC_MEMORY)	+= memory.o
 lib-$(CONFIG_ARC_CONSOLE)	+= arc_con.o
 lib-$(CONFIG_ARC_PROMLIB)	+= promlib.o
-
-ccflags-y			:= -Werror

arch/mips/include/asm/clkdev.h

@@ -0,0 +1,25 @@
+/*
+ *  based on arch/arm/include/asm/clkdev.h
+ *
+ *  Copyright (C) 2008 Russell King.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Helper for the clk API to assist looking up a struct clk.
+ */
+#ifndef __ASM_CLKDEV_H
+#define __ASM_CLKDEV_H
+
+#include <linux/slab.h>
+
+#define __clk_get(clk)	({ 1; })
+#define __clk_put(clk)	do { } while (0)
+
+static inline struct clk_lookup_alloc *__clkdev_alloc(size_t size)
+{
+	return kzalloc(size, GFP_KERNEL);
+}
+
+#endif

arch/mips/include/asm/mach-ath79/ar71xx_regs.h

@@ -1,10 +1,11 @@
 /*
  *  Atheros AR71XX/AR724X/AR913X SoC register definitions
  *
+ *  Copyright (C) 2010-2011 Jaiganesh Narayanan <jnarayanan@atheros.com>
  *  Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org>
  *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
  *
- *  Parts of this file are based on Atheros' 2.6.15 BSP
+ *  Parts of this file are based on Atheros' 2.6.15/2.6.31 BSP
  *
  *  This program is free software; you can redistribute it and/or modify it
  *  under the terms of the GNU General Public License version 2 as published
@@ -60,6 +61,9 @@
 #define AR933X_EHCI_BASE	0x1b000000
 #define AR933X_EHCI_SIZE	0x1000
 
+#define AR934X_WMAC_BASE	(AR71XX_APB_BASE + 0x00100000)
+#define AR934X_WMAC_SIZE	0x20000
+
 /*
  * DDR_CTRL block
  */
@@ -91,6 +95,12 @@
 #define AR933X_DDR_REG_FLUSH_USB	0x84
 #define AR933X_DDR_REG_FLUSH_WMAC	0x88
 
+#define AR934X_DDR_REG_FLUSH_GE0	0x9c
+#define AR934X_DDR_REG_FLUSH_GE1	0xa0
+#define AR934X_DDR_REG_FLUSH_USB	0xa4
+#define AR934X_DDR_REG_FLUSH_PCIE	0xa8
+#define AR934X_DDR_REG_FLUSH_WMAC	0xac
+
 /*
  * PLL block
  */
@@ -150,6 +160,41 @@
 #define AR933X_PLL_CLOCK_CTRL_AHB_DIV_SHIFT	15
 #define AR933X_PLL_CLOCK_CTRL_AHB_DIV_MASK	0x7
 
+#define AR934X_PLL_CPU_CONFIG_REG		0x00
+#define AR934X_PLL_DDR_CONFIG_REG		0x04
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_REG		0x08
+
+#define AR934X_PLL_CPU_CONFIG_NFRAC_SHIFT	0
+#define AR934X_PLL_CPU_CONFIG_NFRAC_MASK	0x3f
+#define AR934X_PLL_CPU_CONFIG_NINT_SHIFT	6
+#define AR934X_PLL_CPU_CONFIG_NINT_MASK		0x3f
+#define AR934X_PLL_CPU_CONFIG_REFDIV_SHIFT	12
+#define AR934X_PLL_CPU_CONFIG_REFDIV_MASK	0x1f
+#define AR934X_PLL_CPU_CONFIG_OUTDIV_SHIFT	19
+#define AR934X_PLL_CPU_CONFIG_OUTDIV_MASK	0x3
+
+#define AR934X_PLL_DDR_CONFIG_NFRAC_SHIFT	0
+#define AR934X_PLL_DDR_CONFIG_NFRAC_MASK	0x3ff
+#define AR934X_PLL_DDR_CONFIG_NINT_SHIFT	10
+#define AR934X_PLL_DDR_CONFIG_NINT_MASK		0x3f
+#define AR934X_PLL_DDR_CONFIG_REFDIV_SHIFT	16
+#define AR934X_PLL_DDR_CONFIG_REFDIV_MASK	0x1f
+#define AR934X_PLL_DDR_CONFIG_OUTDIV_SHIFT	23
+#define AR934X_PLL_DDR_CONFIG_OUTDIV_MASK	0x7
+
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_PLL_BYPASS	BIT(2)
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_PLL_BYPASS	BIT(3)
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_PLL_BYPASS	BIT(4)
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_POST_DIV_SHIFT	5
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_CPU_POST_DIV_MASK	0x1f
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_POST_DIV_SHIFT	10
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_DDR_POST_DIV_MASK	0x1f
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_POST_DIV_SHIFT	15
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_AHB_POST_DIV_MASK	0x1f
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_CPUCLK_FROM_CPUPLL	BIT(20)
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_DDRCLK_FROM_DDRPLL	BIT(21)
+#define AR934X_PLL_CPU_DDR_CLK_CTRL_AHBCLK_FROM_DDRPLL	BIT(24)
+
 /*
  * USB_CONFIG block
  */
@@ -185,6 +230,10 @@
 #define AR933X_RESET_REG_RESET_MODULE		0x1c
 #define AR933X_RESET_REG_BOOTSTRAP		0xac
 
+#define AR934X_RESET_REG_RESET_MODULE		0x1c
+#define AR934X_RESET_REG_BOOTSTRAP		0xb0
+#define AR934X_RESET_REG_PCIE_WMAC_INT_STATUS	0xac
+
 #define MISC_INT_ETHSW			BIT(12)
 #define MISC_INT_TIMER4			BIT(10)
 #define MISC_INT_TIMER3			BIT(9)
@@ -241,6 +290,40 @@
 
 #define AR933X_BOOTSTRAP_REF_CLK_40	BIT(0)
 
+#define AR934X_BOOTSTRAP_SW_OPTION8	BIT(23)
+#define AR934X_BOOTSTRAP_SW_OPTION7	BIT(22)
+#define AR934X_BOOTSTRAP_SW_OPTION6	BIT(21)
+#define AR934X_BOOTSTRAP_SW_OPTION5	BIT(20)
+#define AR934X_BOOTSTRAP_SW_OPTION4	BIT(19)
+#define AR934X_BOOTSTRAP_SW_OPTION3	BIT(18)
+#define AR934X_BOOTSTRAP_SW_OPTION2	BIT(17)
+#define AR934X_BOOTSTRAP_SW_OPTION1	BIT(16)
+#define AR934X_BOOTSTRAP_USB_MODE_DEVICE BIT(7)
+#define AR934X_BOOTSTRAP_PCIE_RC	BIT(6)
+#define AR934X_BOOTSTRAP_EJTAG_MODE	BIT(5)
+#define AR934X_BOOTSTRAP_REF_CLK_40	BIT(4)
+#define AR934X_BOOTSTRAP_BOOT_FROM_SPI	BIT(2)
+#define AR934X_BOOTSTRAP_SDRAM_DISABLED	BIT(1)
+#define AR934X_BOOTSTRAP_DDR1		BIT(0)
+
+#define AR934X_PCIE_WMAC_INT_WMAC_MISC		BIT(0)
+#define AR934X_PCIE_WMAC_INT_WMAC_TX		BIT(1)
+#define AR934X_PCIE_WMAC_INT_WMAC_RXLP		BIT(2)
+#define AR934X_PCIE_WMAC_INT_WMAC_RXHP		BIT(3)
+#define AR934X_PCIE_WMAC_INT_PCIE_RC		BIT(4)
+#define AR934X_PCIE_WMAC_INT_PCIE_RC0		BIT(5)
+#define AR934X_PCIE_WMAC_INT_PCIE_RC1		BIT(6)
+#define AR934X_PCIE_WMAC_INT_PCIE_RC2		BIT(7)
+#define AR934X_PCIE_WMAC_INT_PCIE_RC3		BIT(8)
+#define AR934X_PCIE_WMAC_INT_WMAC_ALL \
+	(AR934X_PCIE_WMAC_INT_WMAC_MISC | AR934X_PCIE_WMAC_INT_WMAC_TX | \
+	 AR934X_PCIE_WMAC_INT_WMAC_RXLP | AR934X_PCIE_WMAC_INT_WMAC_RXHP)
+
+#define AR934X_PCIE_WMAC_INT_PCIE_ALL \
+	(AR934X_PCIE_WMAC_INT_PCIE_RC | AR934X_PCIE_WMAC_INT_PCIE_RC0 | \
+	 AR934X_PCIE_WMAC_INT_PCIE_RC1 | AR934X_PCIE_WMAC_INT_PCIE_RC2 | \
+	 AR934X_PCIE_WMAC_INT_PCIE_RC3)
+
 #define REV_ID_MAJOR_MASK		0xfff0
 #define REV_ID_MAJOR_AR71XX		0x00a0
 #define REV_ID_MAJOR_AR913X		0x00b0
@@ -249,6 +332,9 @@
 #define REV_ID_MAJOR_AR7242		0x1100
 #define REV_ID_MAJOR_AR9330		0x0110
 #define REV_ID_MAJOR_AR9331		0x1110
+#define REV_ID_MAJOR_AR9341		0x0120
+#define REV_ID_MAJOR_AR9342		0x1120
+#define REV_ID_MAJOR_AR9344		0x2120
 
 #define AR71XX_REV_ID_MINOR_MASK	0x3
 #define AR71XX_REV_ID_MINOR_AR7130	0x0
@@ -267,6 +353,8 @@
 
 #define AR724X_REV_ID_REVISION_MASK	0x3
 
+#define AR934X_REV_ID_REVISION_MASK     0xf
+
 /*
  * SPI block
  */
@@ -308,5 +396,6 @@
 #define AR724X_GPIO_COUNT		18
 #define AR913X_GPIO_COUNT		22
 #define AR933X_GPIO_COUNT		30
+#define AR934X_GPIO_COUNT		23
 
 #endif /* __ASM_MACH_AR71XX_REGS_H */

arch/mips/include/asm/mach-ath79/ath79.h

@@ -29,6 +29,9 @@ enum ath79_soc_type {
 	ATH79_SOC_AR9132,
 	ATH79_SOC_AR9330,
 	ATH79_SOC_AR9331,
+	ATH79_SOC_AR9341,
+	ATH79_SOC_AR9342,
+	ATH79_SOC_AR9344,
 };
 
 extern enum ath79_soc_type ath79_soc;
@@ -75,6 +78,26 @@ static inline int soc_is_ar933x(void)
 		ath79_soc == ATH79_SOC_AR9331);
 }
 
+static inline int soc_is_ar9341(void)
+{
+	return (ath79_soc == ATH79_SOC_AR9341);
+}
+
+static inline int soc_is_ar9342(void)
+{
+	return (ath79_soc == ATH79_SOC_AR9342);
+}
+
+static inline int soc_is_ar9344(void)
+{
+	return (ath79_soc == ATH79_SOC_AR9344);
+}
+
+static inline int soc_is_ar934x(void)
+{
+	return soc_is_ar9341() || soc_is_ar9342() || soc_is_ar9344();
+}
+
 extern void __iomem *ath79_ddr_base;
 extern void __iomem *ath79_pll_base;
 extern void __iomem *ath79_reset_base;

arch/mips/include/asm/mach-ath79/irq.h

@@ -10,11 +10,19 @@
 #define __ASM_MACH_ATH79_IRQ_H
 
 #define MIPS_CPU_IRQ_BASE	0
-#define NR_IRQS			40
+#define NR_IRQS			48
 
 #define ATH79_MISC_IRQ_BASE	8
 #define ATH79_MISC_IRQ_COUNT	32
 
+#define ATH79_PCI_IRQ_BASE	(ATH79_MISC_IRQ_BASE + ATH79_MISC_IRQ_COUNT)
+#define ATH79_PCI_IRQ_COUNT	6
+#define ATH79_PCI_IRQ(_x)	(ATH79_PCI_IRQ_BASE + (_x))
+
+#define ATH79_IP2_IRQ_BASE	(ATH79_PCI_IRQ_BASE + ATH79_PCI_IRQ_COUNT)
+#define ATH79_IP2_IRQ_COUNT	2
+#define ATH79_IP2_IRQ(_x)	(ATH79_IP2_IRQ_BASE + (_x))
+
 #define ATH79_CPU_IRQ_IP2	(MIPS_CPU_IRQ_BASE + 2)
 #define ATH79_CPU_IRQ_USB	(MIPS_CPU_IRQ_BASE + 3)
 #define ATH79_CPU_IRQ_GE0	(MIPS_CPU_IRQ_BASE + 4)

arch/mips/include/asm/mach-ath79/pci-ath724x.h

@@ -1,21 +0,0 @@
-/*
- *  Atheros 724x PCI support
- *
- *  Copyright (C) 2011 René Bolldorf <xsecute@googlemail.com>
- *
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- */
-
-#ifndef __ASM_MACH_ATH79_PCI_ATH724X_H
-#define __ASM_MACH_ATH79_PCI_ATH724X_H
-
-struct ath724x_pci_data {
-	int irq;
-	void *pdata;
-};
-
-void ath724x_pci_add_data(struct ath724x_pci_data *data, int size);
-
-#endif /* __ASM_MACH_ATH79_PCI_ATH724X_H */

arch/mips/include/asm/mach-ath79/pci.h

@@ -0,0 +1,28 @@
+/*
+ *  Atheros AR71XX/AR724X PCI support
+ *
+ *  Copyright (C) 2011 René Bolldorf <xsecute@googlemail.com>
+ *  Copyright (C) 2008-2011 Gabor Juhos <juhosg@openwrt.org>
+ *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
+ *
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ */
+
+#ifndef __ASM_MACH_ATH79_PCI_H
+#define __ASM_MACH_ATH79_PCI_H
+
+#if defined(CONFIG_PCI) && defined(CONFIG_SOC_AR71XX)
+int ar71xx_pcibios_init(void);
+#else
+static inline int ar71xx_pcibios_init(void) { return 0; }
+#endif
+
+#if defined(CONFIG_PCI_AR724X)
+int ar724x_pcibios_init(int irq);
+#else
+static inline int ar724x_pcibios_init(int irq) { return 0; }
+#endif
+
+#endif /* __ASM_MACH_ATH79_PCI_H */

arch/mips/include/asm/mach-lantiq/falcon/falcon_irq.h

@@ -0,0 +1,23 @@
+/*
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ *
+ *  Copyright (C) 2010 Thomas Langer <thomas.langer@lantiq.com>
+ */
+
+#ifndef _FALCON_IRQ__
+#define _FALCON_IRQ__
+
+#define INT_NUM_IRQ0			8
+#define INT_NUM_IM0_IRL0		(INT_NUM_IRQ0 + 0)
+#define INT_NUM_IM1_IRL0		(INT_NUM_IM0_IRL0 + 32)
+#define INT_NUM_IM2_IRL0		(INT_NUM_IM1_IRL0 + 32)
+#define INT_NUM_IM3_IRL0		(INT_NUM_IM2_IRL0 + 32)
+#define INT_NUM_IM4_IRL0		(INT_NUM_IM3_IRL0 + 32)
+#define INT_NUM_EXTRA_START		(INT_NUM_IM4_IRL0 + 32)
+#define INT_NUM_IM_OFFSET		(INT_NUM_IM1_IRL0 - INT_NUM_IM0_IRL0)
+
+#define MIPS_CPU_TIMER_IRQ			7
+
+#endif /* _FALCON_IRQ__ */

arch/mips/include/asm/mach-lantiq/falcon/irq.h

@@ -0,0 +1,18 @@
+/*
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ *
+ *  Copyright (C) 2011 Thomas Langer <thomas.langer@lantiq.com>
+ */
+
+#ifndef __FALCON_IRQ_H
+#define __FALCON_IRQ_H
+
+#include <falcon_irq.h>
+
+#define NR_IRQS 328
+
+#include_next <irq.h>
+
+#endif

arch/mips/include/asm/mach-lantiq/falcon/lantiq_soc.h

@@ -0,0 +1,67 @@
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * Copyright (C) 2010 John Crispin <blogic@openwrt.org>
+ */
+
+#ifndef _LTQ_FALCON_H__
+#define _LTQ_FALCON_H__
+
+#ifdef CONFIG_SOC_FALCON
+
+#include <linux/pinctrl/pinctrl.h>
+#include <lantiq.h>
+
+/* Chip IDs */
+#define SOC_ID_FALCON		0x01B8
+
+/* SoC Types */
+#define SOC_TYPE_FALCON		0x01
+
+/*
+ * during early_printk no ioremap possible at this early stage
+ * lets use KSEG1 instead
+ */
+#define LTQ_ASC0_BASE_ADDR	0x1E100C00
+#define LTQ_EARLY_ASC		KSEG1ADDR(LTQ_ASC0_BASE_ADDR)
+
+/* WDT */
+#define LTQ_RST_CAUSE_WDTRST	0x0002
+
+/* CHIP ID */
+#define LTQ_STATUS_BASE_ADDR	0x1E802000
+
+#define FALCON_CHIPID		((u32 *)(KSEG1 + LTQ_STATUS_BASE_ADDR + 0x0c))
+#define FALCON_CHIPTYPE		((u32 *)(KSEG1 + LTQ_STATUS_BASE_ADDR + 0x38))
+#define FALCON_CHIPCONF		((u32 *)(KSEG1 + LTQ_STATUS_BASE_ADDR + 0x40))
+
+/* SYSCTL - start/stop/restart/configure/... different parts of the Soc */
+#define SYSCTL_SYS1		0
+#define SYSCTL_SYSETH		1
+#define SYSCTL_SYSGPE		2
+
+/* BOOT_SEL - find what boot media we have */
+#define BS_FLASH		0x1
+#define BS_SPI                  0x4
+
+/* global register ranges */
+extern __iomem void *ltq_ebu_membase;
+extern __iomem void *ltq_sys1_membase;
+#define ltq_ebu_w32(x, y)	ltq_w32((x), ltq_ebu_membase + (y))
+#define ltq_ebu_r32(x)		ltq_r32(ltq_ebu_membase + (x))
+
+#define ltq_sys1_w32(x, y)	ltq_w32((x), ltq_sys1_membase + (y))
+#define ltq_sys1_r32(x)		ltq_r32(ltq_sys1_membase + (x))
+#define ltq_sys1_w32_mask(clear, set, reg)   \
+	ltq_sys1_w32((ltq_sys1_r32(reg) & ~(clear)) | (set), reg)
+
+/*
+ * to keep the irq code generic we need to define this to 0 as falcon
+ * has no EIU/EBU
+ */
+#define LTQ_EBU_PCC_ISTAT	0
+
+#endif /* CONFIG_SOC_FALCON */
+#endif /* _LTQ_XWAY_H__ */

arch/mips/include/asm/mach-lantiq/gpio.h

@@ -0,0 +1,16 @@
+#ifndef __ASM_MIPS_MACH_LANTIQ_GPIO_H
+#define __ASM_MIPS_MACH_LANTIQ_GPIO_H
+
+static inline int gpio_to_irq(unsigned int gpio)
+{
+	return -1;
+}
+
+#define gpio_get_value __gpio_get_value
+#define gpio_set_value __gpio_set_value
+
+#define gpio_cansleep __gpio_cansleep
+
+#include <asm-generic/gpio.h>
+
+#endif

arch/mips/include/asm/mach-lantiq/lantiq.h

@@ -9,6 +9,8 @@
 #define _LANTIQ_H__
 
 #include <linux/irq.h>
+#include <linux/device.h>
+#include <linux/clk.h>
 
 /* generic reg access functions */
 #define ltq_r32(reg)		__raw_readl(reg)
@@ -21,25 +23,9 @@
 /* register access macros for EBU and CGU */
 #define ltq_ebu_w32(x, y)	ltq_w32((x), ltq_ebu_membase + (y))
 #define ltq_ebu_r32(x)		ltq_r32(ltq_ebu_membase + (x))
-#define ltq_cgu_w32(x, y)	ltq_w32((x), ltq_cgu_membase + (y))
-#define ltq_cgu_r32(x)		ltq_r32(ltq_cgu_membase + (x))
-
+#define ltq_ebu_w32_mask(x, y, z) \
+	ltq_w32_mask(x, y, ltq_ebu_membase + (z))
 extern __iomem void *ltq_ebu_membase;
-extern __iomem void *ltq_cgu_membase;
-
-extern unsigned int ltq_get_cpu_ver(void);
-extern unsigned int ltq_get_soc_type(void);
-
-/* clock speeds */
-#define CLOCK_60M	60000000
-#define CLOCK_83M	83333333
-#define CLOCK_111M	111111111
-#define CLOCK_133M	133333333
-#define CLOCK_167M	166666667
-#define CLOCK_200M	200000000
-#define CLOCK_266M	266666666
-#define CLOCK_333M	333333333
-#define CLOCK_400M	400000000
 
 /* spinlock all ebu i/o */
 extern spinlock_t ebu_lock;
@@ -49,15 +35,21 @@ extern void ltq_disable_irq(struct irq_data *data);
 extern void ltq_mask_and_ack_irq(struct irq_data *data);
 extern void ltq_enable_irq(struct irq_data *data);
 
+/* clock handling */
+extern int clk_activate(struct clk *clk);
+extern void clk_deactivate(struct clk *clk);
+extern struct clk *clk_get_cpu(void);
+extern struct clk *clk_get_fpi(void);
+extern struct clk *clk_get_io(void);
+
+/* find out what bootsource we have */
+extern unsigned char ltq_boot_select(void);
 /* find out what caused the last cpu reset */
 extern int ltq_reset_cause(void);
-#define LTQ_RST_CAUSE_WDTRST	0x20
 
 #define IOPORT_RESOURCE_START	0x10000000
 #define IOPORT_RESOURCE_END	0xffffffff
 #define IOMEM_RESOURCE_START	0x10000000
 #define IOMEM_RESOURCE_END	0xffffffff
-#define LTQ_FLASH_START		0x10000000
-#define LTQ_FLASH_MAX		0x04000000
 
 #endif

arch/mips/include/asm/mach-lantiq/lantiq_platform.h

@@ -9,41 +9,8 @@
 #ifndef _LANTIQ_PLATFORM_H__
 #define _LANTIQ_PLATFORM_H__
 
-#include <linux/mtd/partitions.h>
 #include <linux/socket.h>
 
-/* struct used to pass info to the pci core */
-enum {
-	PCI_CLOCK_INT = 0,
-	PCI_CLOCK_EXT
-};
-
-#define PCI_EXIN0	0x0001
-#define PCI_EXIN1	0x0002
-#define PCI_EXIN2	0x0004
-#define PCI_EXIN3	0x0008
-#define PCI_EXIN4	0x0010
-#define PCI_EXIN5	0x0020
-#define PCI_EXIN_MAX	6
-
-#define PCI_GNT1	0x0040
-#define PCI_GNT2	0x0080
-#define PCI_GNT3	0x0100
-#define PCI_GNT4	0x0200
-
-#define PCI_REQ1	0x0400
-#define PCI_REQ2	0x0800
-#define PCI_REQ3	0x1000
-#define PCI_REQ4	0x2000
-#define PCI_REQ_SHIFT	10
-#define PCI_REQ_MASK	0xf
-
-struct ltq_pci_data {
-	int clock;
-	int gpio;
-	int irq[16];
-};
-
 /* struct used to pass info to network drivers */
 struct ltq_eth_data {
 	struct sockaddr mac;

arch/mips/include/asm/mach-lantiq/xway/lantiq_irq.h

@@ -17,50 +17,8 @@
 #define INT_NUM_IM4_IRL0	(INT_NUM_IRQ0 + 128)
 #define INT_NUM_IM_OFFSET	(INT_NUM_IM1_IRL0 - INT_NUM_IM0_IRL0)
 
-#define LTQ_ASC_TIR(x)		(INT_NUM_IM3_IRL0 + (x * 8))
-#define LTQ_ASC_RIR(x)		(INT_NUM_IM3_IRL0 + (x * 8) + 1)
-#define LTQ_ASC_EIR(x)		(INT_NUM_IM3_IRL0 + (x * 8) + 2)
-
-#define LTQ_ASC_ASE_TIR		INT_NUM_IM2_IRL0
-#define LTQ_ASC_ASE_RIR		(INT_NUM_IM2_IRL0 + 2)
-#define LTQ_ASC_ASE_EIR		(INT_NUM_IM2_IRL0 + 3)
-
-#define LTQ_SSC_TIR		(INT_NUM_IM0_IRL0 + 15)
-#define LTQ_SSC_RIR		(INT_NUM_IM0_IRL0 + 14)
-#define LTQ_SSC_EIR		(INT_NUM_IM0_IRL0 + 16)
-
-#define LTQ_MEI_DYING_GASP_INT	(INT_NUM_IM1_IRL0 + 21)
-#define LTQ_MEI_INT		(INT_NUM_IM1_IRL0 + 23)
-
-#define LTQ_TIMER6_INT		(INT_NUM_IM1_IRL0 + 23)
-#define LTQ_USB_INT		(INT_NUM_IM1_IRL0 + 22)
-#define LTQ_USB_OC_INT		(INT_NUM_IM4_IRL0 + 23)
-
-#define MIPS_CPU_TIMER_IRQ		7
-
 #define LTQ_DMA_CH0_INT		(INT_NUM_IM2_IRL0)
-#define LTQ_DMA_CH1_INT		(INT_NUM_IM2_IRL0 + 1)
-#define LTQ_DMA_CH2_INT		(INT_NUM_IM2_IRL0 + 2)
-#define LTQ_DMA_CH3_INT		(INT_NUM_IM2_IRL0 + 3)
-#define LTQ_DMA_CH4_INT		(INT_NUM_IM2_IRL0 + 4)
-#define LTQ_DMA_CH5_INT		(INT_NUM_IM2_IRL0 + 5)
-#define LTQ_DMA_CH6_INT		(INT_NUM_IM2_IRL0 + 6)
-#define LTQ_DMA_CH7_INT		(INT_NUM_IM2_IRL0 + 7)
-#define LTQ_DMA_CH8_INT		(INT_NUM_IM2_IRL0 + 8)
-#define LTQ_DMA_CH9_INT		(INT_NUM_IM2_IRL0 + 9)
-#define LTQ_DMA_CH10_INT	(INT_NUM_IM2_IRL0 + 10)
-#define LTQ_DMA_CH11_INT	(INT_NUM_IM2_IRL0 + 11)
-#define LTQ_DMA_CH12_INT	(INT_NUM_IM2_IRL0 + 25)
-#define LTQ_DMA_CH13_INT	(INT_NUM_IM2_IRL0 + 26)
-#define LTQ_DMA_CH14_INT	(INT_NUM_IM2_IRL0 + 27)
-#define LTQ_DMA_CH15_INT	(INT_NUM_IM2_IRL0 + 28)
-#define LTQ_DMA_CH16_INT	(INT_NUM_IM2_IRL0 + 29)
-#define LTQ_DMA_CH17_INT	(INT_NUM_IM2_IRL0 + 30)
-#define LTQ_DMA_CH18_INT	(INT_NUM_IM2_IRL0 + 16)
-#define LTQ_DMA_CH19_INT	(INT_NUM_IM2_IRL0 + 21)
-
-#define LTQ_PPE_MBOX_INT	(INT_NUM_IM2_IRL0 + 24)
 
-#define INT_NUM_IM4_IRL14	(INT_NUM_IM4_IRL0 + 14)
+#define MIPS_CPU_TIMER_IRQ	7
 
 #endif

arch/mips/include/asm/mach-lantiq/xway/lantiq_soc.h

@@ -17,38 +17,56 @@
 #define SOC_ID_DANUBE1		0x129
 #define SOC_ID_DANUBE2		0x12B
 #define SOC_ID_TWINPASS		0x12D
-#define SOC_ID_AMAZON_SE	0x152
+#define SOC_ID_AMAZON_SE_1	0x152 /* 50601 */
+#define SOC_ID_AMAZON_SE_2	0x153 /* 50600 */
 #define SOC_ID_ARX188		0x16C
-#define SOC_ID_ARX168		0x16D
+#define SOC_ID_ARX168_1		0x16D
+#define SOC_ID_ARX168_2		0x16E
 #define SOC_ID_ARX182		0x16F
-
-/* SoC Types */
+#define SOC_ID_GRX188		0x170
+#define SOC_ID_GRX168		0x171
+
+#define SOC_ID_VRX288		0x1C0 /* v1.1 */
+#define SOC_ID_VRX282		0x1C1 /* v1.1 */
+#define SOC_ID_VRX268		0x1C2 /* v1.1 */
+#define SOC_ID_GRX268		0x1C8 /* v1.1 */
+#define SOC_ID_GRX288		0x1C9 /* v1.1 */
+#define SOC_ID_VRX288_2		0x00B /* v1.2 */
+#define SOC_ID_VRX268_2		0x00C /* v1.2 */
+#define SOC_ID_GRX288_2		0x00D /* v1.2 */
+#define SOC_ID_GRX282_2		0x00E /* v1.2 */
+
+ /* SoC Types */
 #define SOC_TYPE_DANUBE		0x01
 #define SOC_TYPE_TWINPASS	0x02
 #define SOC_TYPE_AR9		0x03
-#define SOC_TYPE_VR9		0x04
-#define SOC_TYPE_AMAZON_SE	0x05
+#define SOC_TYPE_VR9		0x04 /* v1.1 */
+#define SOC_TYPE_VR9_2		0x05 /* v1.2 */
+#define SOC_TYPE_AMAZON_SE	0x06
+
+/* BOOT_SEL - find what boot media we have */
+#define BS_EXT_ROM		0x0
+#define BS_FLASH		0x1
+#define BS_MII0			0x2
+#define BS_PCI			0x3
+#define BS_UART1		0x4
+#define BS_SPI			0x5
+#define BS_NAND			0x6
+#define BS_RMII0		0x7
+
+/* helpers used to access the cgu */
+#define ltq_cgu_w32(x, y)	ltq_w32((x), ltq_cgu_membase + (y))
+#define ltq_cgu_r32(x)		ltq_r32(ltq_cgu_membase + (x))
+extern __iomem void *ltq_cgu_membase;
 
-/* ASC0/1 - serial port */
-#define LTQ_ASC0_BASE_ADDR	0x1E100400
+/*
+ * during early_printk no ioremap is possible
+ * lets use KSEG1 instead
+ */
 #define LTQ_ASC1_BASE_ADDR	0x1E100C00
-#define LTQ_ASC_SIZE		0x400
-
-/* RCU - reset control unit */
-#define LTQ_RCU_BASE_ADDR	0x1F203000
-#define LTQ_RCU_SIZE		0x1000
-
-/* GPTU - general purpose timer unit */
-#define LTQ_GPTU_BASE_ADDR	0x18000300
-#define LTQ_GPTU_SIZE		0x100
+#define LTQ_EARLY_ASC		KSEG1ADDR(LTQ_ASC1_BASE_ADDR)
 
 /* EBU - external bus unit */
-#define LTQ_EBU_GPIO_START	0x14000000
-#define LTQ_EBU_GPIO_SIZE	0x1000
-
-#define LTQ_EBU_BASE_ADDR	0x1E105300
-#define LTQ_EBU_SIZE		0x100
-
 #define LTQ_EBU_BUSCON0		0x0060
 #define LTQ_EBU_PCC_CON		0x0090
 #define LTQ_EBU_PCC_IEN		0x00A4
@@ -57,85 +75,17 @@
 #define LTQ_EBU_ADDRSEL1	0x0024
 #define EBU_WRDIS		0x80000000
 
-/* CGU - clock generation unit */
-#define LTQ_CGU_BASE_ADDR	0x1F103000
-#define LTQ_CGU_SIZE		0x1000
-
-/* ICU - interrupt control unit */
-#define LTQ_ICU_BASE_ADDR	0x1F880200
-#define LTQ_ICU_SIZE		0x100
-
-/* EIU - external interrupt unit */
-#define LTQ_EIU_BASE_ADDR	0x1F101000
-#define LTQ_EIU_SIZE		0x1000
-
-/* PMU - power management unit */
-#define LTQ_PMU_BASE_ADDR	0x1F102000
-#define LTQ_PMU_SIZE		0x1000
-
-#define PMU_DMA			0x0020
-#define PMU_USB			0x8041
-#define PMU_LED			0x0800
-#define PMU_GPT			0x1000
-#define PMU_PPE			0x2000
-#define PMU_FPI			0x4000
-#define PMU_SWITCH		0x10000000
-
-/* ETOP - ethernet */
-#define LTQ_ETOP_BASE_ADDR	0x1E180000
-#define LTQ_ETOP_SIZE		0x40000
-
-/* DMA */
-#define LTQ_DMA_BASE_ADDR	0x1E104100
-#define LTQ_DMA_SIZE		0x800
-
-/* PCI */
-#define PCI_CR_BASE_ADDR	0x1E105400
-#define PCI_CR_SIZE		0x400
-
 /* WDT */
-#define LTQ_WDT_BASE_ADDR	0x1F8803F0
-#define LTQ_WDT_SIZE		0x10
-
-/* STP - serial to parallel conversion unit */
-#define LTQ_STP_BASE_ADDR	0x1E100BB0
-#define LTQ_STP_SIZE		0x40
-
-/* GPIO */
-#define LTQ_GPIO0_BASE_ADDR	0x1E100B10
-#define LTQ_GPIO1_BASE_ADDR	0x1E100B40
-#define LTQ_GPIO2_BASE_ADDR	0x1E100B70
-#define LTQ_GPIO_SIZE		0x30
-
-/* SSC */
-#define LTQ_SSC_BASE_ADDR	0x1e100800
-#define LTQ_SSC_SIZE		0x100
-
-/* MEI - dsl core */
-#define LTQ_MEI_BASE_ADDR	0x1E116000
-
-/* DEU - data encryption unit */
-#define LTQ_DEU_BASE_ADDR	0x1E103100
+#define LTQ_RST_CAUSE_WDTRST	0x20
 
 /* MPS - multi processor unit (voice) */
 #define LTQ_MPS_BASE_ADDR	(KSEG1 + 0x1F107000)
 #define LTQ_MPS_CHIPID		((u32 *)(LTQ_MPS_BASE_ADDR + 0x0344))
 
 /* request a non-gpio and set the PIO config */
-extern int  ltq_gpio_request(unsigned int pin, unsigned int alt0,
-	unsigned int alt1, unsigned int dir, const char *name);
+#define PMU_PPE			 BIT(13)
 extern void ltq_pmu_enable(unsigned int module);
 extern void ltq_pmu_disable(unsigned int module);
 
-static inline int ltq_is_ar9(void)
-{
-	return (ltq_get_soc_type() == SOC_TYPE_AR9);
-}
-
-static inline int ltq_is_vr9(void)
-{
-	return (ltq_get_soc_type() == SOC_TYPE_VR9);
-}
-
 #endif /* CONFIG_SOC_TYPE_XWAY */
 #endif /* _LTQ_XWAY_H__ */

arch/mips/include/asm/mips-boards/generic.h

@@ -93,8 +93,4 @@ extern void mips_pcibios_init(void);
 #define mips_pcibios_init() do { } while (0)
 #endif
 
-#ifdef CONFIG_KGDB
-extern void kgdb_config(void);
-#endif
-
 #endif  /* __ASM_MIPS_BOARDS_GENERIC_H */

arch/mips/include/asm/module.h

@@ -2,6 +2,7 @@
 #define _ASM_MODULE_H
 
 #include <linux/list.h>
+#include <linux/elf.h>
 #include <asm/uaccess.h>
 
 struct mod_arch_specific {

arch/mips/include/asm/pci.h

@@ -17,6 +17,7 @@
  */
 
 #include <linux/ioport.h>
+#include <linux/of.h>
 
 /*
  * Each pci channel is a top-level PCI bus seem by CPU.  A machine  with
@@ -26,6 +27,7 @@
 struct pci_controller {
 	struct pci_controller *next;
 	struct pci_bus *bus;
+	struct device_node *of_node;
 
 	struct pci_ops *pci_ops;
 	struct resource *mem_resource;
@@ -142,4 +144,8 @@ static inline int pci_get_legacy_ide_irq(struct pci_dev *dev, int channel)
 
 extern char * (*pcibios_plat_setup)(char *str);
 
+/* this function parses memory ranges from a device node */
+extern void __devinit pci_load_of_ranges(struct pci_controller *hose,
+					 struct device_node *node);
+
 #endif /* _ASM_PCI_H */

arch/mips/include/asm/prom.h

@@ -12,6 +12,9 @@
 #define __ASM_PROM_H
 
 #ifdef CONFIG_OF
+#include <linux/bug.h>
+#include <linux/io.h>
+#include <linux/types.h>
 #include <asm/bootinfo.h>
 
 extern int early_init_dt_scan_memory_arch(unsigned long node,
@@ -21,6 +24,29 @@ extern int reserve_mem_mach(unsigned long addr, unsigned long size);
 extern void free_mem_mach(unsigned long addr, unsigned long size);
 
 extern void device_tree_init(void);
+
+static inline unsigned long pci_address_to_pio(phys_addr_t address)
+{
+	/*
+	 * The ioport address can be directly used by inX() / outX()
+	 */
+	BUG_ON(address > IO_SPACE_LIMIT);
+
+	return (unsigned long) address;
+}
+#define pci_address_to_pio pci_address_to_pio
+
+struct boot_param_header;
+
+extern void __dt_setup_arch(struct boot_param_header *bph);
+
+#define dt_setup_arch(sym)						\
+({									\
+	extern struct boot_param_header __dtb_##sym##_begin;		\
+									\
+	__dt_setup_arch(&__dtb_##sym##_begin);				\
+})
+
 #else /* CONFIG_OF */
 static inline void device_tree_init(void) { }
 #endif /* CONFIG_OF */

arch/mips/include/asm/setup.h

@@ -14,7 +14,8 @@ extern void *set_vi_handler(int n, vi_handler_t addr);
 
 extern void *set_except_vector(int n, void *addr);
 extern unsigned long ebase;
-extern void per_cpu_trap_init(void);
+extern void per_cpu_trap_init(bool);
+extern void cpu_cache_init(void);
 
 #endif /* __KERNEL__ */
 

arch/mips/include/asm/termios.h

@@ -60,7 +60,7 @@ struct termio {
 };
 
 #ifdef __KERNEL__
-#include <linux/module.h>
+#include <asm/uaccess.h>
 
 /*
  *	intr=^C		quit=^\		erase=del	kill=^U

arch/mips/include/asm/traps.h

@@ -25,6 +25,7 @@ extern void (*board_nmi_handler_setup)(void);
 extern void (*board_ejtag_handler_setup)(void);
 extern void (*board_bind_eic_interrupt)(int irq, int regset);
 extern void (*board_ebase_setup)(void);
+extern void (*board_cache_error_setup)(void);
 
 extern int register_nmi_notifier(struct notifier_block *nb);
 

arch/mips/include/asm/uasm.h

@@ -11,7 +11,7 @@
 #include <linux/types.h>
 
 #ifdef CONFIG_EXPORT_UASM
-#include <linux/module.h>
+#include <linux/export.h>
 #define __uasminit
 #define __uasminitdata
 #define UASM_EXPORT_SYMBOL(sym) EXPORT_SYMBOL(sym)

arch/mips/jz4740/Makefile

@@ -16,5 +16,3 @@ obj-$(CONFIG_JZ4740_QI_LB60)	+= board-qi_lb60.o
 # PM support
 
 obj-$(CONFIG_PM) += pm.o
-
-ccflags-y := -Werror -Wall

arch/mips/kernel/cpu-probe.c

@@ -340,7 +340,7 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "R2000";
 		c->isa_level = MIPS_CPU_ISA_I;
 		c->options = MIPS_CPU_TLB | MIPS_CPU_3K_CACHE |
-		             MIPS_CPU_NOFPUEX;
+			     MIPS_CPU_NOFPUEX;
 		if (__cpu_has_fpu())
 			c->options |= MIPS_CPU_FPU;
 		c->tlbsize = 64;
@@ -361,7 +361,7 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		}
 		c->isa_level = MIPS_CPU_ISA_I;
 		c->options = MIPS_CPU_TLB | MIPS_CPU_3K_CACHE |
-		             MIPS_CPU_NOFPUEX;
+			     MIPS_CPU_NOFPUEX;
 		if (__cpu_has_fpu())
 			c->options |= MIPS_CPU_FPU;
 		c->tlbsize = 64;
@@ -387,8 +387,8 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 
 		c->isa_level = MIPS_CPU_ISA_III;
 		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
-		             MIPS_CPU_WATCH | MIPS_CPU_VCE |
-		             MIPS_CPU_LLSC;
+			     MIPS_CPU_WATCH | MIPS_CPU_VCE |
+			     MIPS_CPU_LLSC;
 		c->tlbsize = 48;
 		break;
 	case PRID_IMP_VR41XX:
@@ -434,7 +434,7 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "R4300";
 		c->isa_level = MIPS_CPU_ISA_III;
 		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
-		             MIPS_CPU_LLSC;
+			     MIPS_CPU_LLSC;
 		c->tlbsize = 32;
 		break;
 	case PRID_IMP_R4600:
@@ -446,7 +446,7 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		c->tlbsize = 48;
 		break;
 	#if 0
- 	case PRID_IMP_R4650:
+	case PRID_IMP_R4650:
 		/*
 		 * This processor doesn't have an MMU, so it's not
 		 * "real easy" to run Linux on it. It is left purely
@@ -455,9 +455,9 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		 */
 		c->cputype = CPU_R4650;
 		__cpu_name[cpu] = "R4650";
-	 	c->isa_level = MIPS_CPU_ISA_III;
+		c->isa_level = MIPS_CPU_ISA_III;
 		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_LLSC;
-	        c->tlbsize = 48;
+		c->tlbsize = 48;
 		break;
 	#endif
 	case PRID_IMP_TX39:
@@ -488,7 +488,7 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "R4700";
 		c->isa_level = MIPS_CPU_ISA_III;
 		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
-		             MIPS_CPU_LLSC;
+			     MIPS_CPU_LLSC;
 		c->tlbsize = 48;
 		break;
 	case PRID_IMP_TX49:
@@ -505,7 +505,7 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "R5000";
 		c->isa_level = MIPS_CPU_ISA_IV;
 		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
-		             MIPS_CPU_LLSC;
+			     MIPS_CPU_LLSC;
 		c->tlbsize = 48;
 		break;
 	case PRID_IMP_R5432:
@@ -513,7 +513,7 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "R5432";
 		c->isa_level = MIPS_CPU_ISA_IV;
 		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
-		             MIPS_CPU_WATCH | MIPS_CPU_LLSC;
+			     MIPS_CPU_WATCH | MIPS_CPU_LLSC;
 		c->tlbsize = 48;
 		break;
 	case PRID_IMP_R5500:
@@ -521,7 +521,7 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "R5500";
 		c->isa_level = MIPS_CPU_ISA_IV;
 		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
-		             MIPS_CPU_WATCH | MIPS_CPU_LLSC;
+			     MIPS_CPU_WATCH | MIPS_CPU_LLSC;
 		c->tlbsize = 48;
 		break;
 	case PRID_IMP_NEVADA:
@@ -529,7 +529,7 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "Nevada";
 		c->isa_level = MIPS_CPU_ISA_IV;
 		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
-		             MIPS_CPU_DIVEC | MIPS_CPU_LLSC;
+			     MIPS_CPU_DIVEC | MIPS_CPU_LLSC;
 		c->tlbsize = 48;
 		break;
 	case PRID_IMP_R6000:
@@ -537,7 +537,7 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "R6000";
 		c->isa_level = MIPS_CPU_ISA_II;
 		c->options = MIPS_CPU_TLB | MIPS_CPU_FPU |
-		             MIPS_CPU_LLSC;
+			     MIPS_CPU_LLSC;
 		c->tlbsize = 32;
 		break;
 	case PRID_IMP_R6000A:
@@ -545,7 +545,7 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "R6000A";
 		c->isa_level = MIPS_CPU_ISA_II;
 		c->options = MIPS_CPU_TLB | MIPS_CPU_FPU |
-		             MIPS_CPU_LLSC;
+			     MIPS_CPU_LLSC;
 		c->tlbsize = 32;
 		break;
 	case PRID_IMP_RM7000:
@@ -553,7 +553,7 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "RM7000";
 		c->isa_level = MIPS_CPU_ISA_IV;
 		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
-		             MIPS_CPU_LLSC;
+			     MIPS_CPU_LLSC;
 		/*
 		 * Undocumented RM7000:  Bit 29 in the info register of
 		 * the RM7000 v2.0 indicates if the TLB has 48 or 64
@@ -569,7 +569,7 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "RM9000";
 		c->isa_level = MIPS_CPU_ISA_IV;
 		c->options = R4K_OPTS | MIPS_CPU_FPU | MIPS_CPU_32FPR |
-		             MIPS_CPU_LLSC;
+			     MIPS_CPU_LLSC;
 		/*
 		 * Bit 29 in the info register of the RM9000
 		 * indicates if the TLB has 48 or 64 entries.
@@ -584,8 +584,8 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "RM8000";
 		c->isa_level = MIPS_CPU_ISA_IV;
 		c->options = MIPS_CPU_TLB | MIPS_CPU_4KEX |
-		             MIPS_CPU_FPU | MIPS_CPU_32FPR |
-		             MIPS_CPU_LLSC;
+			     MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_LLSC;
 		c->tlbsize = 384;      /* has weird TLB: 3-way x 128 */
 		break;
 	case PRID_IMP_R10000:
@@ -593,9 +593,9 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "R10000";
 		c->isa_level = MIPS_CPU_ISA_IV;
 		c->options = MIPS_CPU_TLB | MIPS_CPU_4K_CACHE | MIPS_CPU_4KEX |
-		             MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_FPU | MIPS_CPU_32FPR |
 			     MIPS_CPU_COUNTER | MIPS_CPU_WATCH |
-		             MIPS_CPU_LLSC;
+			     MIPS_CPU_LLSC;
 		c->tlbsize = 64;
 		break;
 	case PRID_IMP_R12000:
@@ -603,9 +603,9 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "R12000";
 		c->isa_level = MIPS_CPU_ISA_IV;
 		c->options = MIPS_CPU_TLB | MIPS_CPU_4K_CACHE | MIPS_CPU_4KEX |
-		             MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_FPU | MIPS_CPU_32FPR |
 			     MIPS_CPU_COUNTER | MIPS_CPU_WATCH |
-		             MIPS_CPU_LLSC;
+			     MIPS_CPU_LLSC;
 		c->tlbsize = 64;
 		break;
 	case PRID_IMP_R14000:
@@ -613,9 +613,9 @@ static inline void cpu_probe_legacy(struct cpuinfo_mips *c, unsigned int cpu)
 		__cpu_name[cpu] = "R14000";
 		c->isa_level = MIPS_CPU_ISA_IV;
 		c->options = MIPS_CPU_TLB | MIPS_CPU_4K_CACHE | MIPS_CPU_4KEX |
-		             MIPS_CPU_FPU | MIPS_CPU_32FPR |
+			     MIPS_CPU_FPU | MIPS_CPU_32FPR |
 			     MIPS_CPU_COUNTER | MIPS_CPU_WATCH |
-		             MIPS_CPU_LLSC;
+			     MIPS_CPU_LLSC;
 		c->tlbsize = 64;
 		break;
 	case PRID_IMP_LOONGSON2:
@@ -739,7 +739,7 @@ static inline unsigned int decode_config3(struct cpuinfo_mips *c)
 	if (config3 & MIPS_CONF3_VEIC)
 		c->options |= MIPS_CPU_VEIC;
 	if (config3 & MIPS_CONF3_MT)
-	        c->ases |= MIPS_ASE_MIPSMT;
+		c->ases |= MIPS_ASE_MIPSMT;
 	if (config3 & MIPS_CONF3_ULRI)
 		c->options |= MIPS_CPU_ULRI;
 
@@ -767,7 +767,7 @@ static void __cpuinit decode_configs(struct cpuinfo_mips *c)
 
 	/* MIPS32 or MIPS64 compliant CPU.  */
 	c->options = MIPS_CPU_4KEX | MIPS_CPU_4K_CACHE | MIPS_CPU_COUNTER |
-	             MIPS_CPU_DIVEC | MIPS_CPU_LLSC | MIPS_CPU_MCHECK;
+		     MIPS_CPU_DIVEC | MIPS_CPU_LLSC | MIPS_CPU_MCHECK;
 
 	c->scache.flags = MIPS_CACHE_NOT_PRESENT;
 

arch/mips/kernel/perf_event_mipsxx.c

@@ -1532,7 +1532,8 @@ init_hw_perf_events(void)
 		irq = MSC01E_INT_BASE + MSC01E_INT_PERFCTR;
 	} else {
 #endif
-		if (cp0_perfcount_irq >= 0)
+		if ((cp0_perfcount_irq >= 0) &&
+				(cp0_compare_irq != cp0_perfcount_irq))
 			irq = MIPS_CPU_IRQ_BASE + cp0_perfcount_irq;
 		else
 			irq = -1;

arch/mips/kernel/proc.c

@@ -41,27 +41,27 @@ static int show_cpuinfo(struct seq_file *m, void *v)
 
 	seq_printf(m, "processor\t\t: %ld\n", n);
 	sprintf(fmt, "cpu model\t\t: %%s V%%d.%%d%s\n",
-	        cpu_data[n].options & MIPS_CPU_FPU ? "  FPU V%d.%d" : "");
+		      cpu_data[n].options & MIPS_CPU_FPU ? "  FPU V%d.%d" : "");
 	seq_printf(m, fmt, __cpu_name[n],
-	                           (version >> 4) & 0x0f, version & 0x0f,
-	                           (fp_vers >> 4) & 0x0f, fp_vers & 0x0f);
+		      (version >> 4) & 0x0f, version & 0x0f,
+		      (fp_vers >> 4) & 0x0f, fp_vers & 0x0f);
 	seq_printf(m, "BogoMIPS\t\t: %u.%02u\n",
-	              cpu_data[n].udelay_val / (500000/HZ),
-	              (cpu_data[n].udelay_val / (5000/HZ)) % 100);
+		      cpu_data[n].udelay_val / (500000/HZ),
+		      (cpu_data[n].udelay_val / (5000/HZ)) % 100);
 	seq_printf(m, "wait instruction\t: %s\n", cpu_wait ? "yes" : "no");
 	seq_printf(m, "microsecond timers\t: %s\n",
-	              cpu_has_counter ? "yes" : "no");
+		      cpu_has_counter ? "yes" : "no");
 	seq_printf(m, "tlb_entries\t\t: %d\n", cpu_data[n].tlbsize);
 	seq_printf(m, "extra interrupt vector\t: %s\n",
-	              cpu_has_divec ? "yes" : "no");
+		      cpu_has_divec ? "yes" : "no");
 	seq_printf(m, "hardware watchpoint\t: %s",
-		   cpu_has_watch ? "yes, " : "no\n");
+		      cpu_has_watch ? "yes, " : "no\n");
 	if (cpu_has_watch) {
 		seq_printf(m, "count: %d, address/irw mask: [",
-			   cpu_data[n].watch_reg_count);
+		      cpu_data[n].watch_reg_count);
 		for (i = 0; i < cpu_data[n].watch_reg_count; i++)
 			seq_printf(m, "%s0x%04x", i ? ", " : "" ,
-				   cpu_data[n].watch_reg_masks[i]);
+				cpu_data[n].watch_reg_masks[i]);
 		seq_printf(m, "]\n");
 	}
 	seq_printf(m, "ASEs implemented\t:%s%s%s%s%s%s\n",
@@ -73,13 +73,13 @@ static int show_cpuinfo(struct seq_file *m, void *v)
 		      cpu_has_mipsmt ? " mt" : ""
 		);
 	seq_printf(m, "shadow register sets\t: %d\n",
-		       cpu_data[n].srsets);
+		      cpu_data[n].srsets);
 	seq_printf(m, "kscratch registers\t: %d\n",
-		   hweight8(cpu_data[n].kscratch_mask));
+		      hweight8(cpu_data[n].kscratch_mask));
 	seq_printf(m, "core\t\t\t: %d\n", cpu_data[n].core);
 
 	sprintf(fmt, "VCE%%c exceptions\t\t: %s\n",
-	        cpu_has_vce ? "%u" : "not available");
+		      cpu_has_vce ? "%u" : "not available");
 	seq_printf(m, fmt, 'D', vced_count);
 	seq_printf(m, fmt, 'I', vcei_count);
 	seq_printf(m, "\n");

arch/mips/kernel/prom.c

@@ -95,3 +95,16 @@ void __init device_tree_init(void)
 	/* free the space reserved for the dt blob */
 	free_mem_mach(base, size);
 }
+
+void __init __dt_setup_arch(struct boot_param_header *bph)
+{
+	if (be32_to_cpu(bph->magic) != OF_DT_HEADER) {
+		pr_err("DTB has bad magic, ignoring builtin OF DTB\n");
+
+		return;
+	}
+
+	initial_boot_params = bph;
+
+	early_init_devtree(initial_boot_params);
+}

arch/mips/kernel/setup.c

@@ -605,6 +605,8 @@ void __init setup_arch(char **cmdline_p)
 
 	resource_init();
 	plat_smp_setup();
+
+	cpu_cache_init();
 }
 
 unsigned long kernelsp[NR_CPUS];

arch/mips/kernel/smp.c

@@ -106,7 +106,7 @@ asmlinkage __cpuinit void start_secondary(void)
 #endif /* CONFIG_MIPS_MT_SMTC */
 	cpu_probe();
 	cpu_report();
-	per_cpu_trap_init();
+	per_cpu_trap_init(false);
 	mips_clockevent_init();
 	mp_ops->init_secondary();
 

arch/mips/kernel/traps.c

@@ -15,6 +15,7 @@
 #include <linux/compiler.h>
 #include <linux/init.h>
 #include <linux/kernel.h>
+#include <linux/module.h>
 #include <linux/mm.h>
 #include <linux/sched.h>
 #include <linux/smp.h>
@@ -91,7 +92,7 @@ void (*board_nmi_handler_setup)(void);
 void (*board_ejtag_handler_setup)(void);
 void (*board_bind_eic_interrupt)(int irq, int regset);
 void (*board_ebase_setup)(void);
-
+void __cpuinitdata(*board_cache_error_setup)(void);
 
 static void show_raw_backtrace(unsigned long reg29)
 {
@@ -1490,7 +1491,6 @@ void *set_vi_handler(int n, vi_handler_t addr)
 	return set_vi_srs_handler(n, addr, 0);
 }
 
-extern void cpu_cache_init(void);
 extern void tlb_init(void);
 extern void flush_tlb_handlers(void);
 
@@ -1517,7 +1517,7 @@ static int __init ulri_disable(char *s)
 }
 __setup("noulri", ulri_disable);
 
-void __cpuinit per_cpu_trap_init(void)
+void __cpuinit per_cpu_trap_init(bool is_boot_cpu)
 {
 	unsigned int cpu = smp_processor_id();
 	unsigned int status_set = ST0_CU0;
@@ -1616,7 +1616,9 @@ void __cpuinit per_cpu_trap_init(void)
 #ifdef CONFIG_MIPS_MT_SMTC
 	if (bootTC) {
 #endif /* CONFIG_MIPS_MT_SMTC */
-		cpu_cache_init();
+		/* Boot CPU's cache setup in setup_arch(). */
+		if (!is_boot_cpu)
+			cpu_cache_init();
 		tlb_init();
 #ifdef CONFIG_MIPS_MT_SMTC
 	} else if (!secondaryTC) {
@@ -1632,7 +1634,7 @@ void __cpuinit per_cpu_trap_init(void)
 }
 
 /* Install CPU exception handler */
-void __init set_handler(unsigned long offset, void *addr, unsigned long size)
+void __cpuinit set_handler(unsigned long offset, void *addr, unsigned long size)
 {
 	memcpy((void *)(ebase + offset), addr, size);
 	local_flush_icache_range(ebase + offset, ebase + offset + size);
@@ -1693,7 +1695,7 @@ void __init trap_init(void)
 
 	if (board_ebase_setup)
 		board_ebase_setup();
-	per_cpu_trap_init();
+	per_cpu_trap_init(true);
 
 	/*
 	 * Copy the generic exception handlers to their final destination.
@@ -1797,6 +1799,9 @@ void __init trap_init(void)
 
 	set_except_vector(26, handle_dsp);
 
+	if (board_cache_error_setup)
+		board_cache_error_setup();
+
 	if (cpu_has_vce)
 		/* Special exception: R4[04]00 uses also the divec space. */
 		memcpy((void *)(ebase + 0x180), &except_vec3_r4000, 0x100);

arch/mips/lantiq/Kconfig

@@ -16,8 +16,22 @@ config SOC_XWAY
 	bool "XWAY"
 	select SOC_TYPE_XWAY
 	select HW_HAS_PCI
+
+config SOC_FALCON
+	bool "FALCON"
+
+endchoice
+
+choice
+	prompt "Devicetree"
+
+config DT_EASY50712
+	bool "Easy50712"
+	depends on SOC_XWAY
 endchoice
 
-source "arch/mips/lantiq/xway/Kconfig"
+config PCI_LANTIQ
+	bool "PCI Support"
+	depends on SOC_XWAY && PCI
 
 endif

arch/mips/lantiq/Makefile

@@ -4,8 +4,11 @@
 # under the terms of the GNU General Public License version 2 as published
 # by the Free Software Foundation.
 
-obj-y := irq.o setup.o clk.o prom.o devices.o
+obj-y := irq.o clk.o prom.o
+
+obj-y += dts/
 
 obj-$(CONFIG_EARLY_PRINTK) += early_printk.o
 
 obj-$(CONFIG_SOC_TYPE_XWAY) += xway/
+obj-$(CONFIG_SOC_FALCON) += falcon/

arch/mips/lantiq/Platform

@@ -6,3 +6,4 @@ platform-$(CONFIG_LANTIQ)	+= lantiq/
 cflags-$(CONFIG_LANTIQ)		+= -I$(srctree)/arch/mips/include/asm/mach-lantiq
 load-$(CONFIG_LANTIQ)		= 0xffffffff80002000
 cflags-$(CONFIG_SOC_TYPE_XWAY)	+= -I$(srctree)/arch/mips/include/asm/mach-lantiq/xway
+cflags-$(CONFIG_SOC_FALCON)	+= -I$(srctree)/arch/mips/include/asm/mach-lantiq/falcon

arch/mips/lantiq/clk.c

@@ -12,6 +12,7 @@
 #include <linux/kernel.h>
 #include <linux/types.h>
 #include <linux/clk.h>
+#include <linux/clkdev.h>
 #include <linux/err.h>
 #include <linux/list.h>
 
@@ -22,44 +23,32 @@
 #include <lantiq_soc.h>
 
 #include "clk.h"
+#include "prom.h"
 
-struct clk {
-	const char *name;
-	unsigned long rate;
-	unsigned long (*get_rate) (void);
-};
+/* lantiq socs have 3 static clocks */
+static struct clk cpu_clk_generic[3];
 
-static struct clk *cpu_clk;
-static int cpu_clk_cnt;
+void clkdev_add_static(unsigned long cpu, unsigned long fpi, unsigned long io)
+{
+	cpu_clk_generic[0].rate = cpu;
+	cpu_clk_generic[1].rate = fpi;
+	cpu_clk_generic[2].rate = io;
+}
 
-/* lantiq socs have 3 static clocks */
-static struct clk cpu_clk_generic[] = {
-	{
-		.name = "cpu",
-		.get_rate = ltq_get_cpu_hz,
-	}, {
-		.name = "fpi",
-		.get_rate = ltq_get_fpi_hz,
-	}, {
-		.name = "io",
-		.get_rate = ltq_get_io_region_clock,
-	},
-};
-
-static struct resource ltq_cgu_resource = {
-	.name	= "cgu",
-	.start	= LTQ_CGU_BASE_ADDR,
-	.end	= LTQ_CGU_BASE_ADDR + LTQ_CGU_SIZE - 1,
-	.flags	= IORESOURCE_MEM,
-};
-
-/* remapped clock register range */
-void __iomem *ltq_cgu_membase;
-
-void clk_init(void)
+struct clk *clk_get_cpu(void)
+{
+	return &cpu_clk_generic[0];
+}
+
+struct clk *clk_get_fpi(void)
+{
+	return &cpu_clk_generic[1];
+}
+EXPORT_SYMBOL_GPL(clk_get_fpi);
+
+struct clk *clk_get_io(void)
 {
-	cpu_clk = cpu_clk_generic;
-	cpu_clk_cnt = ARRAY_SIZE(cpu_clk_generic);
+	return &cpu_clk_generic[2];
 }
 
 static inline int clk_good(struct clk *clk)
@@ -82,38 +71,71 @@ unsigned long clk_get_rate(struct clk *clk)
 }
 EXPORT_SYMBOL(clk_get_rate);
 
-struct clk *clk_get(struct device *dev, const char *id)
+int clk_set_rate(struct clk *clk, unsigned long rate)
 {
-	int i;
-
-	for (i = 0; i < cpu_clk_cnt; i++)
-		if (!strcmp(id, cpu_clk[i].name))
-			return &cpu_clk[i];
-	BUG();
-	return ERR_PTR(-ENOENT);
-}
-EXPORT_SYMBOL(clk_get);
-
-void clk_put(struct clk *clk)
-{
-	/* not used */
+	if (unlikely(!clk_good(clk)))
+		return 0;
+	if (clk->rates && *clk->rates) {
+		unsigned long *r = clk->rates;
+
+		while (*r && (*r != rate))
+			r++;
+		if (!*r) {
+			pr_err("clk %s.%s: trying to set invalid rate %ld\n",
+				clk->cl.dev_id, clk->cl.con_id, rate);
+			return -1;
+		}
+	}
+	clk->rate = rate;
+	return 0;
 }
-EXPORT_SYMBOL(clk_put);
+EXPORT_SYMBOL(clk_set_rate);
 
 int clk_enable(struct clk *clk)
 {
-	/* not used */
-	return 0;
+	if (unlikely(!clk_good(clk)))
+		return -1;
+
+	if (clk->enable)
+		return clk->enable(clk);
+
+	return -1;
 }
 EXPORT_SYMBOL(clk_enable);
 
 void clk_disable(struct clk *clk)
 {
-	/* not used */
+	if (unlikely(!clk_good(clk)))
+		return;
+
+	if (clk->disable)
+		clk->disable(clk);
 }
 EXPORT_SYMBOL(clk_disable);
 
-static inline u32 ltq_get_counter_resolution(void)
+int clk_activate(struct clk *clk)
+{
+	if (unlikely(!clk_good(clk)))
+		return -1;
+
+	if (clk->activate)
+		return clk->activate(clk);
+
+	return -1;
+}
+EXPORT_SYMBOL(clk_activate);
+
+void clk_deactivate(struct clk *clk)
+{
+	if (unlikely(!clk_good(clk)))
+		return;
+
+	if (clk->deactivate)
+		clk->deactivate(clk);
+}
+EXPORT_SYMBOL(clk_deactivate);
+
+static inline u32 get_counter_resolution(void)
 {
 	u32 res;
 
@@ -133,21 +155,11 @@ void __init plat_time_init(void)
 {
 	struct clk *clk;
 
-	if (insert_resource(&iomem_resource, &ltq_cgu_resource) < 0)
-		panic("Failed to insert cgu memory");
+	ltq_soc_init();
 
-	if (request_mem_region(ltq_cgu_resource.start,
-			resource_size(&ltq_cgu_resource), "cgu") < 0)
-		panic("Failed to request cgu memory");
-
-	ltq_cgu_membase = ioremap_nocache(ltq_cgu_resource.start,
-				resource_size(&ltq_cgu_resource));
-	if (!ltq_cgu_membase) {
-		pr_err("Failed to remap cgu memory\n");
-		unreachable();
-	}
-	clk = clk_get(0, "cpu");
-	mips_hpt_frequency = clk_get_rate(clk) / ltq_get_counter_resolution();
+	clk = clk_get_cpu();
+	mips_hpt_frequency = clk_get_rate(clk) / get_counter_resolution();
 	write_c0_compare(read_c0_count());
+	pr_info("CPU Clock: %ldMHz\n", clk_get_rate(clk) / 1000000);
 	clk_put(clk);
 }

arch/mips/lantiq/clk.h

@@ -9,10 +9,70 @@
 #ifndef _LTQ_CLK_H__
 #define _LTQ_CLK_H__
 
-extern void clk_init(void);
+#include <linux/clkdev.h>
 
-extern unsigned long ltq_get_cpu_hz(void);
-extern unsigned long ltq_get_fpi_hz(void);
-extern unsigned long ltq_get_io_region_clock(void);
+/* clock speeds */
+#define CLOCK_33M	33333333
+#define CLOCK_60M	60000000
+#define CLOCK_62_5M	62500000
+#define CLOCK_83M	83333333
+#define CLOCK_83_5M	83500000
+#define CLOCK_98_304M	98304000
+#define CLOCK_100M	100000000
+#define CLOCK_111M	111111111
+#define CLOCK_125M	125000000
+#define CLOCK_133M	133333333
+#define CLOCK_150M	150000000
+#define CLOCK_166M	166666666
+#define CLOCK_167M	166666667
+#define CLOCK_196_608M	196608000
+#define CLOCK_200M	200000000
+#define CLOCK_250M	250000000
+#define CLOCK_266M	266666666
+#define CLOCK_300M	300000000
+#define CLOCK_333M	333333333
+#define CLOCK_393M	393215332
+#define CLOCK_400M	400000000
+#define CLOCK_500M	500000000
+#define CLOCK_600M	600000000
+
+/* clock out speeds */
+#define CLOCK_32_768K	32768
+#define CLOCK_1_536M	1536000
+#define CLOCK_2_5M	2500000
+#define CLOCK_12M	12000000
+#define CLOCK_24M	24000000
+#define CLOCK_25M	25000000
+#define CLOCK_30M	30000000
+#define CLOCK_40M	40000000
+#define CLOCK_48M	48000000
+#define CLOCK_50M	50000000
+#define CLOCK_60M	60000000
+
+struct clk {
+	struct clk_lookup cl;
+	unsigned long rate;
+	unsigned long *rates;
+	unsigned int module;
+	unsigned int bits;
+	unsigned long (*get_rate) (void);
+	int (*enable) (struct clk *clk);
+	void (*disable) (struct clk *clk);
+	int (*activate) (struct clk *clk);
+	void (*deactivate) (struct clk *clk);
+	void (*reboot) (struct clk *clk);
+};
+
+extern void clkdev_add_static(unsigned long cpu, unsigned long fpi,
+				unsigned long io);
+
+extern unsigned long ltq_danube_cpu_hz(void);
+extern unsigned long ltq_danube_fpi_hz(void);
+
+extern unsigned long ltq_ar9_cpu_hz(void);
+extern unsigned long ltq_ar9_fpi_hz(void);
+
+extern unsigned long ltq_vr9_cpu_hz(void);
+extern unsigned long ltq_vr9_fpi_hz(void);
 
 #endif

arch/mips/lantiq/devices.c

@@ -1,120 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
- */
-
-#include <linux/init.h>
-#include <linux/export.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/kernel.h>
-#include <linux/reboot.h>
-#include <linux/platform_device.h>
-#include <linux/leds.h>
-#include <linux/etherdevice.h>
-#include <linux/time.h>
-#include <linux/io.h>
-#include <linux/gpio.h>
-
-#include <asm/bootinfo.h>
-#include <asm/irq.h>
-
-#include <lantiq_soc.h>
-
-#include "devices.h"
-
-/* nor flash */
-static struct resource ltq_nor_resource = {
-	.name	= "nor",
-	.start	= LTQ_FLASH_START,
-	.end	= LTQ_FLASH_START + LTQ_FLASH_MAX - 1,
-	.flags  = IORESOURCE_MEM,
-};
-
-static struct platform_device ltq_nor = {
-	.name		= "ltq_nor",
-	.resource	= &ltq_nor_resource,
-	.num_resources	= 1,
-};
-
-void __init ltq_register_nor(struct physmap_flash_data *data)
-{
-	ltq_nor.dev.platform_data = data;
-	platform_device_register(&ltq_nor);
-}
-
-/* watchdog */
-static struct resource ltq_wdt_resource = {
-	.name	= "watchdog",
-	.start  = LTQ_WDT_BASE_ADDR,
-	.end    = LTQ_WDT_BASE_ADDR + LTQ_WDT_SIZE - 1,
-	.flags  = IORESOURCE_MEM,
-};
-
-void __init ltq_register_wdt(void)
-{
-	platform_device_register_simple("ltq_wdt", 0, &ltq_wdt_resource, 1);
-}
-
-/* asc ports */
-static struct resource ltq_asc0_resources[] = {
-	{
-		.name	= "asc0",
-		.start  = LTQ_ASC0_BASE_ADDR,
-		.end    = LTQ_ASC0_BASE_ADDR + LTQ_ASC_SIZE - 1,
-		.flags  = IORESOURCE_MEM,
-	},
-	IRQ_RES(tx, LTQ_ASC_TIR(0)),
-	IRQ_RES(rx, LTQ_ASC_RIR(0)),
-	IRQ_RES(err, LTQ_ASC_EIR(0)),
-};
-
-static struct resource ltq_asc1_resources[] = {
-	{
-		.name	= "asc1",
-		.start  = LTQ_ASC1_BASE_ADDR,
-		.end    = LTQ_ASC1_BASE_ADDR + LTQ_ASC_SIZE - 1,
-		.flags  = IORESOURCE_MEM,
-	},
-	IRQ_RES(tx, LTQ_ASC_TIR(1)),
-	IRQ_RES(rx, LTQ_ASC_RIR(1)),
-	IRQ_RES(err, LTQ_ASC_EIR(1)),
-};
-
-void __init ltq_register_asc(int port)
-{
-	switch (port) {
-	case 0:
-		platform_device_register_simple("ltq_asc", 0,
-			ltq_asc0_resources, ARRAY_SIZE(ltq_asc0_resources));
-		break;
-	case 1:
-		platform_device_register_simple("ltq_asc", 1,
-			ltq_asc1_resources, ARRAY_SIZE(ltq_asc1_resources));
-		break;
-	default:
-		break;
-	}
-}
-
-#ifdef CONFIG_PCI
-/* pci */
-static struct platform_device ltq_pci = {
-	.name		= "ltq_pci",
-	.num_resources	= 0,
-};
-
-void __init ltq_register_pci(struct ltq_pci_data *data)
-{
-	ltq_pci.dev.platform_data = data;
-	platform_device_register(&ltq_pci);
-}
-#else
-void __init ltq_register_pci(struct ltq_pci_data *data)
-{
-	pr_err("kernel is compiled without PCI support\n");
-}
-#endif

arch/mips/lantiq/devices.h

@@ -1,23 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
- */
-
-#ifndef _LTQ_DEVICES_H__
-#define _LTQ_DEVICES_H__
-
-#include <lantiq_platform.h>
-#include <linux/mtd/physmap.h>
-
-#define IRQ_RES(resname, irq) \
-	{.name = #resname, .start = (irq), .flags = IORESOURCE_IRQ}
-
-extern void ltq_register_nor(struct physmap_flash_data *data);
-extern void ltq_register_wdt(void);
-extern void ltq_register_asc(int port);
-extern void ltq_register_pci(struct ltq_pci_data *data);
-
-#endif

arch/mips/lantiq/dts/Makefile

@@ -0,0 +1,4 @@
+obj-$(CONFIG_DT_EASY50712) := easy50712.dtb.o
+
+$(obj)/%.dtb: $(obj)/%.dts
+	$(call if_changed,dtc)

arch/mips/lantiq/dts/danube.dtsi

@@ -0,0 +1,105 @@
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "lantiq,xway", "lantiq,danube";
+
+	cpus {
+		cpu@0 {
+			compatible = "mips,mips24Kc";
+		};
+	};
+
+	biu@1F800000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "lantiq,biu", "simple-bus";
+		reg = <0x1F800000 0x800000>;
+		ranges = <0x0 0x1F800000 0x7FFFFF>;
+
+		icu0: icu@80200 {
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			compatible = "lantiq,icu";
+			reg = <0x80200 0x120>;
+		};
+
+		watchdog@803F0 {
+			compatible = "lantiq,wdt";
+			reg = <0x803F0 0x10>;
+		};
+	};
+
+	sram@1F000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "lantiq,sram";
+		reg = <0x1F000000 0x800000>;
+		ranges = <0x0 0x1F000000 0x7FFFFF>;
+
+		eiu0: eiu@101000 {
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			interrupt-parent;
+			compatible = "lantiq,eiu-xway";
+			reg = <0x101000 0x1000>;
+		};
+
+		pmu0: pmu@102000 {
+			compatible = "lantiq,pmu-xway";
+			reg = <0x102000 0x1000>;
+		};
+
+		cgu0: cgu@103000 {
+			compatible = "lantiq,cgu-xway";
+			reg = <0x103000 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		rcu0: rcu@203000 {
+			compatible = "lantiq,rcu-xway";
+			reg = <0x203000 0x1000>;
+		};
+	};
+
+	fpi@10000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "lantiq,fpi", "simple-bus";
+		ranges = <0x0 0x10000000 0xEEFFFFF>;
+		reg = <0x10000000 0xEF00000>;
+
+		gptu@E100A00 {
+			compatible = "lantiq,gptu-xway";
+			reg = <0xE100A00 0x100>;
+		};
+
+		serial@E100C00 {
+			compatible = "lantiq,asc";
+			reg = <0xE100C00 0x400>;
+			interrupt-parent = <&icu0>;
+			interrupts = <112 113 114>;
+		};
+
+		dma0: dma@E104100 {
+			compatible = "lantiq,dma-xway";
+			reg = <0xE104100 0x800>;
+		};
+
+		ebu0: ebu@E105300 {
+			compatible = "lantiq,ebu-xway";
+			reg = <0xE105300 0x100>;
+		};
+
+		pci0: pci@E105400 {
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			compatible = "lantiq,pci-xway";
+			bus-range = <0x0 0x0>;
+			ranges = <0x2000000 0 0x8000000 0x8000000 0 0x2000000	/* pci memory */
+				  0x1000000 0 0x00000000 0xAE00000 0 0x200000>;	/* io space */
+			reg = <0x7000000 0x8000		/* config space */
+				0xE105400 0x400>;	/* pci bridge */
+		};
+	};
+};

arch/mips/lantiq/dts/easy50712.dts

@@ -0,0 +1,113 @@
+/dts-v1/;
+
+/include/ "danube.dtsi"
+
+/ {
+	chosen {
+		bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
+	};
+
+	memory@0 {
+		reg = <0x0 0x2000000>;
+	};
+
+	fpi@10000000 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		localbus@0 {
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <0 0 0x0 0x3ffffff /* addrsel0 */
+				1 0 0x4000000 0x4000010>; /* addsel1 */
+			compatible = "lantiq,localbus", "simple-bus";
+
+			nor-boot@0 {
+				compatible = "lantiq,nor";
+				bank-width = <2>;
+				reg = <0 0x0 0x2000000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				partition@0 {
+					label = "uboot";
+					reg = <0x00000 0x10000>; /* 64 KB */
+				};
+
+				partition@10000 {
+					label = "uboot_env";
+					reg = <0x10000 0x10000>; /* 64 KB */
+				};
+
+				partition@20000 {
+					label = "linux";
+					reg = <0x20000 0x3d0000>;
+				};
+
+				partition@400000 {
+					label = "rootfs";
+					reg = <0x400000 0x400000>;
+				};
+			};
+		};
+
+		gpio: pinmux@E100B10 {
+			compatible = "lantiq,pinctrl-xway";
+			pinctrl-names = "default";
+			pinctrl-0 = <&state_default>;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+			reg = <0xE100B10 0xA0>;
+
+			state_default: pinmux {
+				stp {
+					lantiq,groups = "stp";
+					lantiq,function = "stp";
+				};
+				exin {
+					lantiq,groups = "exin1";
+					lantiq,function = "exin";
+				};
+				pci {
+					lantiq,groups = "gnt1";
+					lantiq,function = "pci";
+				};
+				conf_out {
+					lantiq,pins = "io4", "io5", "io6"; /* stp */
+					lantiq,open-drain;
+					lantiq,pull = <0>;
+				};
+			};
+		};
+
+		etop@E180000 {
+			compatible = "lantiq,etop-xway";
+			reg = <0xE180000 0x40000>;
+			interrupt-parent = <&icu0>;
+			interrupts = <73 78>;
+			phy-mode = "rmii";
+			mac-address = [ 00 11 22 33 44 55 ];
+		};
+
+		stp0: stp@E100BB0 {
+			#gpio-cells = <2>;
+			compatible = "lantiq,gpio-stp-xway";
+			gpio-controller;
+			reg = <0xE100BB0 0x40>;
+
+			lantiq,shadow = <0xfff>;
+			lantiq,groups = <0x3>;
+		};
+
+		pci@E105400 {
+			lantiq,bus-clock = <33333333>;
+			interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+			interrupt-map = <
+                                0x7000 0 0 1 &icu0 29 1 // slot 14, irq 29
+			>;
+			gpios-reset = <&gpio 21 0>;
+			req-mask = <0x1>;		/* GNT1 */
+		};
+
+	};
+};

arch/mips/lantiq/early_printk.c

@@ -6,17 +6,16 @@
  *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
  */
 
-#include <linux/init.h>
 #include <linux/cpu.h>
-
-#include <lantiq.h>
 #include <lantiq_soc.h>
 
-/* no ioremap possible at this early stage, lets use KSEG1 instead  */
-#define LTQ_ASC_BASE	KSEG1ADDR(LTQ_ASC1_BASE_ADDR)
 #define ASC_BUF		1024
-#define LTQ_ASC_FSTAT	((u32 *)(LTQ_ASC_BASE + 0x0048))
-#define LTQ_ASC_TBUF	((u32 *)(LTQ_ASC_BASE + 0x0020))
+#define LTQ_ASC_FSTAT	((u32 *)(LTQ_EARLY_ASC + 0x0048))
+#ifdef __BIG_ENDIAN
+#define LTQ_ASC_TBUF	((u32 *)(LTQ_EARLY_ASC + 0x0020 + 3))
+#else
+#define LTQ_ASC_TBUF	((u32 *)(LTQ_EARLY_ASC + 0x0020))
+#endif
 #define TXMASK		0x3F00
 #define TXOFFSET	8
 
@@ -27,7 +26,7 @@ void prom_putchar(char c)
 	local_irq_save(flags);
 	do { } while ((ltq_r32(LTQ_ASC_FSTAT) & TXMASK) >> TXOFFSET);
 	if (c == '\n')
-		ltq_w32('\r', LTQ_ASC_TBUF);
-	ltq_w32(c, LTQ_ASC_TBUF);
+		ltq_w8('\r', LTQ_ASC_TBUF);
+	ltq_w8(c, LTQ_ASC_TBUF);
 	local_irq_restore(flags);
 }

arch/mips/lantiq/falcon/Makefile

@@ -0,0 +1 @@
+obj-y := prom.o reset.o sysctrl.o

arch/mips/lantiq/falcon/prom.c

@@ -0,0 +1,87 @@
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * Copyright (C) 2012 Thomas Langer <thomas.langer@lantiq.com>
+ * Copyright (C) 2012 John Crispin <blogic@openwrt.org>
+ */
+
+#include <linux/kernel.h>
+#include <asm/io.h>
+
+#include <lantiq_soc.h>
+
+#include "../prom.h"
+
+#define SOC_FALCON	"Falcon"
+#define SOC_FALCON_D	"Falcon-D"
+#define SOC_FALCON_V	"Falcon-V"
+#define SOC_FALCON_M	"Falcon-M"
+
+#define COMP_FALCON	"lantiq,falcon"
+
+#define PART_SHIFT	12
+#define PART_MASK	0x0FFFF000
+#define REV_SHIFT	28
+#define REV_MASK	0xF0000000
+#define SREV_SHIFT	22
+#define SREV_MASK	0x03C00000
+#define TYPE_SHIFT	26
+#define TYPE_MASK	0x3C000000
+
+/* reset, nmi and ejtag exception vectors */
+#define BOOT_REG_BASE	(KSEG1 | 0x1F200000)
+#define BOOT_RVEC	(BOOT_REG_BASE | 0x00)
+#define BOOT_NVEC	(BOOT_REG_BASE | 0x04)
+#define BOOT_EVEC	(BOOT_REG_BASE | 0x08)
+
+void __init ltq_soc_nmi_setup(void)
+{
+	extern void (*nmi_handler)(void);
+
+	ltq_w32((unsigned long)&nmi_handler, (void *)BOOT_NVEC);
+}
+
+void __init ltq_soc_ejtag_setup(void)
+{
+	extern void (*ejtag_debug_handler)(void);
+
+	ltq_w32((unsigned long)&ejtag_debug_handler, (void *)BOOT_EVEC);
+}
+
+void __init ltq_soc_detect(struct ltq_soc_info *i)
+{
+	u32 type;
+	i->partnum = (ltq_r32(FALCON_CHIPID) & PART_MASK) >> PART_SHIFT;
+	i->rev = (ltq_r32(FALCON_CHIPID) & REV_MASK) >> REV_SHIFT;
+	i->srev = ((ltq_r32(FALCON_CHIPCONF) & SREV_MASK) >> SREV_SHIFT);
+	i->compatible = COMP_FALCON;
+	i->type = SOC_TYPE_FALCON;
+	sprintf(i->rev_type, "%c%d%d", (i->srev & 0x4) ? ('B') : ('A'),
+		i->rev & 0x7, (i->srev & 0x3) + 1);
+
+	switch (i->partnum) {
+	case SOC_ID_FALCON:
+		type = (ltq_r32(FALCON_CHIPTYPE) & TYPE_MASK) >> TYPE_SHIFT;
+		switch (type) {
+		case 0:
+			i->name = SOC_FALCON_D;
+			break;
+		case 1:
+			i->name = SOC_FALCON_V;
+			break;
+		case 2:
+			i->name = SOC_FALCON_M;
+			break;
+		default:
+			i->name = SOC_FALCON;
+			break;
+		}
+		break;
+
+	default:
+		unreachable();
+		break;
+	}
+}

arch/mips/lantiq/falcon/reset.c

@@ -0,0 +1,90 @@
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * Copyright (C) 2012 Thomas Langer <thomas.langer@lantiq.com>
+ * Copyright (C) 2012 John Crispin <blogic@openwrt.org>
+ */
+
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/pm.h>
+#include <asm/reboot.h>
+#include <linux/export.h>
+
+#include <lantiq_soc.h>
+
+/* CPU0 Reset Source Register */
+#define SYS1_CPU0RS		0x0040
+/* reset cause mask */
+#define CPU0RS_MASK		0x0003
+/* CPU0 Boot Mode Register */
+#define SYS1_BM			0x00a0
+/* boot mode mask */
+#define BM_MASK			0x0005
+
+/* allow platform code to find out what surce we booted from */
+unsigned char ltq_boot_select(void)
+{
+	return ltq_sys1_r32(SYS1_BM) & BM_MASK;
+}
+
+/* allow the watchdog driver to find out what the boot reason was */
+int ltq_reset_cause(void)
+{
+	return ltq_sys1_r32(SYS1_CPU0RS) & CPU0RS_MASK;
+}
+EXPORT_SYMBOL_GPL(ltq_reset_cause);
+
+#define BOOT_REG_BASE	(KSEG1 | 0x1F200000)
+#define BOOT_PW1_REG	(BOOT_REG_BASE | 0x20)
+#define BOOT_PW2_REG	(BOOT_REG_BASE | 0x24)
+#define BOOT_PW1	0x4C545100
+#define BOOT_PW2	0x0051544C
+
+#define WDT_REG_BASE	(KSEG1 | 0x1F8803F0)
+#define WDT_PW1		0x00BE0000
+#define WDT_PW2		0x00DC0000
+
+static void machine_restart(char *command)
+{
+	local_irq_disable();
+
+	/* reboot magic */
+	ltq_w32(BOOT_PW1, (void *)BOOT_PW1_REG); /* 'LTQ\0' */
+	ltq_w32(BOOT_PW2, (void *)BOOT_PW2_REG); /* '\0QTL' */
+	ltq_w32(0, (void *)BOOT_REG_BASE); /* reset Bootreg RVEC */
+
+	/* watchdog magic */
+	ltq_w32(WDT_PW1, (void *)WDT_REG_BASE);
+	ltq_w32(WDT_PW2 |
+		(0x3 << 26) | /* PWL */
+		(0x2 << 24) | /* CLKDIV */
+		(0x1 << 31) | /* enable */
+		(1), /* reload */
+		(void *)WDT_REG_BASE);
+	unreachable();
+}
+
+static void machine_halt(void)
+{
+	local_irq_disable();
+	unreachable();
+}
+
+static void machine_power_off(void)
+{
+	local_irq_disable();
+	unreachable();
+}
+
+static int __init mips_reboot_setup(void)
+{
+	_machine_restart = machine_restart;
+	_machine_halt = machine_halt;
+	pm_power_off = machine_power_off;
+	return 0;
+}
+
+arch_initcall(mips_reboot_setup);

arch/mips/lantiq/falcon/sysctrl.c

@@ -0,0 +1,260 @@
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ *
+ * Copyright (C) 2011 Thomas Langer <thomas.langer@lantiq.com>
+ * Copyright (C) 2011 John Crispin <blogic@openwrt.org>
+ */
+
+#include <linux/ioport.h>
+#include <linux/export.h>
+#include <linux/clkdev.h>
+#include <linux/of_address.h>
+#include <asm/delay.h>
+
+#include <lantiq_soc.h>
+
+#include "../clk.h"
+
+/* infrastructure control register */
+#define SYS1_INFRAC		0x00bc
+/* Configuration fuses for drivers and pll */
+#define STATUS_CONFIG		0x0040
+
+/* GPE frequency selection */
+#define GPPC_OFFSET		24
+#define GPEFREQ_MASK		0x00000C0
+#define GPEFREQ_OFFSET		10
+/* Clock status register */
+#define SYSCTL_CLKS		0x0000
+/* Clock enable register */
+#define SYSCTL_CLKEN		0x0004
+/* Clock clear register */
+#define SYSCTL_CLKCLR		0x0008
+/* Activation Status Register */
+#define SYSCTL_ACTS		0x0020
+/* Activation Register */
+#define SYSCTL_ACT		0x0024
+/* Deactivation Register */
+#define SYSCTL_DEACT		0x0028
+/* reboot Register */
+#define SYSCTL_RBT		0x002c
+/* CPU0 Clock Control Register */
+#define SYS1_CPU0CC		0x0040
+/* HRST_OUT_N Control Register */
+#define SYS1_HRSTOUTC		0x00c0
+/* clock divider bit */
+#define CPU0CC_CPUDIV		0x0001
+
+/* Activation Status Register */
+#define ACTS_ASC1_ACT	0x00000800
+#define ACTS_I2C_ACT	0x00004000
+#define ACTS_P0		0x00010000
+#define ACTS_P1		0x00010000
+#define ACTS_P2		0x00020000
+#define ACTS_P3		0x00020000
+#define ACTS_P4		0x00040000
+#define ACTS_PADCTRL0	0x00100000
+#define ACTS_PADCTRL1	0x00100000
+#define ACTS_PADCTRL2	0x00200000
+#define ACTS_PADCTRL3	0x00200000
+#define ACTS_PADCTRL4	0x00400000
+
+#define sysctl_w32(m, x, y)	ltq_w32((x), sysctl_membase[m] + (y))
+#define sysctl_r32(m, x)	ltq_r32(sysctl_membase[m] + (x))
+#define sysctl_w32_mask(m, clear, set, reg)	\
+		sysctl_w32(m, (sysctl_r32(m, reg) & ~(clear)) | (set), reg)
+
+#define status_w32(x, y)	ltq_w32((x), status_membase + (y))
+#define status_r32(x)		ltq_r32(status_membase + (x))
+
+static void __iomem *sysctl_membase[3], *status_membase;
+void __iomem *ltq_sys1_membase, *ltq_ebu_membase;
+
+void falcon_trigger_hrst(int level)
+{
+	sysctl_w32(SYSCTL_SYS1, level & 1, SYS1_HRSTOUTC);
+}
+
+static inline void sysctl_wait(struct clk *clk,
+		unsigned int test, unsigned int reg)
+{
+	int err = 1000000;
+
+	do {} while (--err && ((sysctl_r32(clk->module, reg)
+					& clk->bits) != test));
+	if (!err)
+		pr_err("module de/activation failed %d %08X %08X %08X\n",
+			clk->module, clk->bits, test,
+			sysctl_r32(clk->module, reg) & clk->bits);
+}
+
+static int sysctl_activate(struct clk *clk)
+{
+	sysctl_w32(clk->module, clk->bits, SYSCTL_CLKEN);
+	sysctl_w32(clk->module, clk->bits, SYSCTL_ACT);
+	sysctl_wait(clk, clk->bits, SYSCTL_ACTS);
+	return 0;
+}
+
+static void sysctl_deactivate(struct clk *clk)
+{
+	sysctl_w32(clk->module, clk->bits, SYSCTL_CLKCLR);
+	sysctl_w32(clk->module, clk->bits, SYSCTL_DEACT);
+	sysctl_wait(clk, 0, SYSCTL_ACTS);
+}
+
+static int sysctl_clken(struct clk *clk)
+{
+	sysctl_w32(clk->module, clk->bits, SYSCTL_CLKEN);
+	sysctl_wait(clk, clk->bits, SYSCTL_CLKS);
+	return 0;
+}
+
+static void sysctl_clkdis(struct clk *clk)
+{
+	sysctl_w32(clk->module, clk->bits, SYSCTL_CLKCLR);
+	sysctl_wait(clk, 0, SYSCTL_CLKS);
+}
+
+static void sysctl_reboot(struct clk *clk)
+{
+	unsigned int act;
+	unsigned int bits;
+
+	act = sysctl_r32(clk->module, SYSCTL_ACT);
+	bits = ~act & clk->bits;
+	if (bits != 0) {
+		sysctl_w32(clk->module, bits, SYSCTL_CLKEN);
+		sysctl_w32(clk->module, bits, SYSCTL_ACT);
+		sysctl_wait(clk, bits, SYSCTL_ACTS);
+	}
+	sysctl_w32(clk->module, act & clk->bits, SYSCTL_RBT);
+	sysctl_wait(clk, clk->bits, SYSCTL_ACTS);
+}
+
+/* enable the ONU core */
+static void falcon_gpe_enable(void)
+{
+	unsigned int freq;
+	unsigned int status;
+
+	/* if if the clock is already enabled */
+	status = sysctl_r32(SYSCTL_SYS1, SYS1_INFRAC);
+	if (status & (1 << (GPPC_OFFSET + 1)))
+		return;
+
+	if (status_r32(STATUS_CONFIG) == 0)
+		freq = 1; /* use 625MHz on unfused chip */
+	else
+		freq = (status_r32(STATUS_CONFIG) &
+			GPEFREQ_MASK) >>
+			GPEFREQ_OFFSET;
+
+	/* apply new frequency */
+	sysctl_w32_mask(SYSCTL_SYS1, 7 << (GPPC_OFFSET + 1),
+		freq << (GPPC_OFFSET + 2) , SYS1_INFRAC);
+	udelay(1);
+
+	/* enable new frequency */
+	sysctl_w32_mask(SYSCTL_SYS1, 0, 1 << (GPPC_OFFSET + 1), SYS1_INFRAC);
+	udelay(1);
+}
+
+static inline void clkdev_add_sys(const char *dev, unsigned int module,
+					unsigned int bits)
+{
+	struct clk *clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
+
+	clk->cl.dev_id = dev;
+	clk->cl.con_id = NULL;
+	clk->cl.clk = clk;
+	clk->module = module;
+	clk->activate = sysctl_activate;
+	clk->deactivate = sysctl_deactivate;
+	clk->enable = sysctl_clken;
+	clk->disable = sysctl_clkdis;
+	clk->reboot = sysctl_reboot;
+	clkdev_add(&clk->cl);
+}
+
+void __init ltq_soc_init(void)
+{
+	struct device_node *np_status =
+		of_find_compatible_node(NULL, NULL, "lantiq,status-falcon");
+	struct device_node *np_ebu =
+		of_find_compatible_node(NULL, NULL, "lantiq,ebu-falcon");
+	struct device_node *np_sys1 =
+		of_find_compatible_node(NULL, NULL, "lantiq,sys1-falcon");
+	struct device_node *np_syseth =
+		of_find_compatible_node(NULL, NULL, "lantiq,syseth-falcon");
+	struct device_node *np_sysgpe =
+		of_find_compatible_node(NULL, NULL, "lantiq,sysgpe-falcon");
+	struct resource res_status, res_ebu, res_sys[3];
+	int i;
+
+	/* check if all the core register ranges are available */
+	if (!np_status || !np_ebu || !np_sys1 || !np_syseth || !np_sysgpe)
+		panic("Failed to load core nodes from devicetree");
+
+	if (of_address_to_resource(np_status, 0, &res_status) ||
+			of_address_to_resource(np_ebu, 0, &res_ebu) ||
+			of_address_to_resource(np_sys1, 0, &res_sys[0]) ||
+			of_address_to_resource(np_syseth, 0, &res_sys[1]) ||
+			of_address_to_resource(np_sysgpe, 0, &res_sys[2]))
+		panic("Failed to get core resources");
+
+	if ((request_mem_region(res_status.start, resource_size(&res_status),
+				res_status.name) < 0) ||
+		(request_mem_region(res_ebu.start, resource_size(&res_ebu),
+				res_ebu.name) < 0) ||
+		(request_mem_region(res_sys[0].start,
+				resource_size(&res_sys[0]),
+				res_sys[0].name) < 0) ||
+		(request_mem_region(res_sys[1].start,
+				resource_size(&res_sys[1]),
+				res_sys[1].name) < 0) ||
+		(request_mem_region(res_sys[2].start,
+				resource_size(&res_sys[2]),
+				res_sys[2].name) < 0))
+		pr_err("Failed to request core reources");
+
+	status_membase = ioremap_nocache(res_status.start,
+					resource_size(&res_status));
+	ltq_ebu_membase = ioremap_nocache(res_ebu.start,
+					resource_size(&res_ebu));
+
+	if (!status_membase || !ltq_ebu_membase)
+		panic("Failed to remap core resources");
+
+	for (i = 0; i < 3; i++) {
+		sysctl_membase[i] = ioremap_nocache(res_sys[i].start,
+						resource_size(&res_sys[i]));
+		if (!sysctl_membase[i])
+			panic("Failed to remap sysctrl resources");
+	}
+	ltq_sys1_membase = sysctl_membase[0];
+
+	falcon_gpe_enable();
+
+	/* get our 3 static rates for cpu, fpi and io clocks */
+	if (ltq_sys1_r32(SYS1_CPU0CC) & CPU0CC_CPUDIV)
+		clkdev_add_static(CLOCK_200M, CLOCK_100M, CLOCK_200M);
+	else
+		clkdev_add_static(CLOCK_400M, CLOCK_100M, CLOCK_200M);
+
+	/* add our clock domains */
+	clkdev_add_sys("1d810000.gpio", SYSCTL_SYSETH, ACTS_P0);
+	clkdev_add_sys("1d810100.gpio", SYSCTL_SYSETH, ACTS_P2);
+	clkdev_add_sys("1e800100.gpio", SYSCTL_SYS1, ACTS_P1);
+	clkdev_add_sys("1e800200.gpio", SYSCTL_SYS1, ACTS_P3);
+	clkdev_add_sys("1e800300.gpio", SYSCTL_SYS1, ACTS_P4);
+	clkdev_add_sys("1db01000.pad", SYSCTL_SYSETH, ACTS_PADCTRL0);
+	clkdev_add_sys("1db02000.pad", SYSCTL_SYSETH, ACTS_PADCTRL2);
+	clkdev_add_sys("1e800400.pad", SYSCTL_SYS1, ACTS_PADCTRL1);
+	clkdev_add_sys("1e800500.pad", SYSCTL_SYS1, ACTS_PADCTRL3);
+	clkdev_add_sys("1e800600.pad", SYSCTL_SYS1, ACTS_PADCTRL4);
+	clkdev_add_sys("1e100C00.serial", SYSCTL_SYS1, ACTS_ASC1_ACT);
+	clkdev_add_sys("1e200000.i2c", SYSCTL_SYS1, ACTS_I2C_ACT);
+}

arch/mips/lantiq/irq.c

@@ -9,6 +9,11 @@
 
 #include <linux/interrupt.h>
 #include <linux/ioport.h>
+#include <linux/sched.h>
+#include <linux/irqdomain.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
 
 #include <asm/bootinfo.h>
 #include <asm/irq_cpu.h>
@@ -16,7 +21,7 @@
 #include <lantiq_soc.h>
 #include <irq.h>
 
-/* register definitions */
+/* register definitions - internal irqs */
 #define LTQ_ICU_IM0_ISR		0x0000
 #define LTQ_ICU_IM0_IER		0x0008
 #define LTQ_ICU_IM0_IOSR	0x0010
@@ -25,6 +30,7 @@
 #define LTQ_ICU_IM1_ISR		0x0028
 #define LTQ_ICU_OFFSET		(LTQ_ICU_IM1_ISR - LTQ_ICU_IM0_ISR)
 
+/* register definitions - external irqs */
 #define LTQ_EIU_EXIN_C		0x0000
 #define LTQ_EIU_EXIN_INIC	0x0004
 #define LTQ_EIU_EXIN_INEN	0x000C
@@ -37,10 +43,14 @@
 #define LTQ_EIU_IR4		(INT_NUM_IM1_IRL0 + 1)
 #define LTQ_EIU_IR5		(INT_NUM_IM1_IRL0 + 2)
 #define LTQ_EIU_IR6		(INT_NUM_IM2_IRL0 + 30)
-
+#define XWAY_EXIN_COUNT		3
 #define MAX_EIU			6
 
-/* irqs generated by device attached to the EBU need to be acked in
+/* the performance counter */
+#define LTQ_PERF_IRQ		(INT_NUM_IM4_IRL0 + 31)
+
+/*
+ * irqs generated by devices attached to the EBU need to be acked in
  * a special manner
  */
 #define LTQ_ICU_EBU_IRQ		22
@@ -51,6 +61,17 @@
 #define ltq_eiu_w32(x, y)	ltq_w32((x), ltq_eiu_membase + (y))
 #define ltq_eiu_r32(x)		ltq_r32(ltq_eiu_membase + (x))
 
+/* our 2 ipi interrupts for VSMP */
+#define MIPS_CPU_IPI_RESCHED_IRQ	0
+#define MIPS_CPU_IPI_CALL_IRQ		1
+
+/* we have a cascade of 8 irqs */
+#define MIPS_CPU_IRQ_CASCADE		8
+
+#if defined(CONFIG_MIPS_MT_SMP) || defined(CONFIG_MIPS_MT_SMTC)
+int gic_present;
+#endif
+
 static unsigned short ltq_eiu_irq[MAX_EIU] = {
 	LTQ_EIU_IR0,
 	LTQ_EIU_IR1,
@@ -60,64 +81,51 @@ static unsigned short ltq_eiu_irq[MAX_EIU] = {
 	LTQ_EIU_IR5,
 };
 
-static struct resource ltq_icu_resource = {
-	.name	= "icu",
-	.start	= LTQ_ICU_BASE_ADDR,
-	.end	= LTQ_ICU_BASE_ADDR + LTQ_ICU_SIZE - 1,
-	.flags	= IORESOURCE_MEM,
-};
-
-static struct resource ltq_eiu_resource = {
-	.name	= "eiu",
-	.start	= LTQ_EIU_BASE_ADDR,
-	.end	= LTQ_EIU_BASE_ADDR + LTQ_ICU_SIZE - 1,
-	.flags	= IORESOURCE_MEM,
-};
-
+static int exin_avail;
 static void __iomem *ltq_icu_membase;
 static void __iomem *ltq_eiu_membase;
 
 void ltq_disable_irq(struct irq_data *d)
 {
 	u32 ier = LTQ_ICU_IM0_IER;
-	int irq_nr = d->irq - INT_NUM_IRQ0;
+	int offset = d->hwirq - MIPS_CPU_IRQ_CASCADE;
 
-	ier += LTQ_ICU_OFFSET * (irq_nr / INT_NUM_IM_OFFSET);
-	irq_nr %= INT_NUM_IM_OFFSET;
-	ltq_icu_w32(ltq_icu_r32(ier) & ~(1 << irq_nr), ier);
+	ier += LTQ_ICU_OFFSET * (offset / INT_NUM_IM_OFFSET);
+	offset %= INT_NUM_IM_OFFSET;
+	ltq_icu_w32(ltq_icu_r32(ier) & ~BIT(offset), ier);
 }
 
 void ltq_mask_and_ack_irq(struct irq_data *d)
 {
 	u32 ier = LTQ_ICU_IM0_IER;
 	u32 isr = LTQ_ICU_IM0_ISR;
-	int irq_nr = d->irq - INT_NUM_IRQ0;
+	int offset = d->hwirq - MIPS_CPU_IRQ_CASCADE;
 
-	ier += LTQ_ICU_OFFSET * (irq_nr / INT_NUM_IM_OFFSET);
-	isr += LTQ_ICU_OFFSET * (irq_nr / INT_NUM_IM_OFFSET);
-	irq_nr %= INT_NUM_IM_OFFSET;
-	ltq_icu_w32(ltq_icu_r32(ier) & ~(1 << irq_nr), ier);
-	ltq_icu_w32((1 << irq_nr), isr);
+	ier += LTQ_ICU_OFFSET * (offset / INT_NUM_IM_OFFSET);
+	isr += LTQ_ICU_OFFSET * (offset / INT_NUM_IM_OFFSET);
+	offset %= INT_NUM_IM_OFFSET;
+	ltq_icu_w32(ltq_icu_r32(ier) & ~BIT(offset), ier);
+	ltq_icu_w32(BIT(offset), isr);
 }
 
 static void ltq_ack_irq(struct irq_data *d)
 {
 	u32 isr = LTQ_ICU_IM0_ISR;
-	int irq_nr = d->irq - INT_NUM_IRQ0;
+	int offset = d->hwirq - MIPS_CPU_IRQ_CASCADE;
 
-	isr += LTQ_ICU_OFFSET * (irq_nr / INT_NUM_IM_OFFSET);
-	irq_nr %= INT_NUM_IM_OFFSET;
-	ltq_icu_w32((1 << irq_nr), isr);
+	isr += LTQ_ICU_OFFSET * (offset / INT_NUM_IM_OFFSET);
+	offset %= INT_NUM_IM_OFFSET;
+	ltq_icu_w32(BIT(offset), isr);
 }
 
 void ltq_enable_irq(struct irq_data *d)
 {
 	u32 ier = LTQ_ICU_IM0_IER;
-	int irq_nr = d->irq - INT_NUM_IRQ0;
+	int offset = d->hwirq - MIPS_CPU_IRQ_CASCADE;
 
-	ier += LTQ_ICU_OFFSET  * (irq_nr / INT_NUM_IM_OFFSET);
-	irq_nr %= INT_NUM_IM_OFFSET;
-	ltq_icu_w32(ltq_icu_r32(ier) | (1 << irq_nr), ier);
+	ier += LTQ_ICU_OFFSET  * (offset / INT_NUM_IM_OFFSET);
+	offset %= INT_NUM_IM_OFFSET;
+	ltq_icu_w32(ltq_icu_r32(ier) | BIT(offset), ier);
 }
 
 static unsigned int ltq_startup_eiu_irq(struct irq_data *d)
@@ -126,15 +134,15 @@ static unsigned int ltq_startup_eiu_irq(struct irq_data *d)
 
 	ltq_enable_irq(d);
 	for (i = 0; i < MAX_EIU; i++) {
-		if (d->irq == ltq_eiu_irq[i]) {
+		if (d->hwirq == ltq_eiu_irq[i]) {
 			/* low level - we should really handle set_type */
 			ltq_eiu_w32(ltq_eiu_r32(LTQ_EIU_EXIN_C) |
 				(0x6 << (i * 4)), LTQ_EIU_EXIN_C);
 			/* clear all pending */
-			ltq_eiu_w32(ltq_eiu_r32(LTQ_EIU_EXIN_INIC) & ~(1 << i),
+			ltq_eiu_w32(ltq_eiu_r32(LTQ_EIU_EXIN_INIC) & ~BIT(i),
 				LTQ_EIU_EXIN_INIC);
 			/* enable */
-			ltq_eiu_w32(ltq_eiu_r32(LTQ_EIU_EXIN_INEN) | (1 << i),
+			ltq_eiu_w32(ltq_eiu_r32(LTQ_EIU_EXIN_INEN) | BIT(i),
 				LTQ_EIU_EXIN_INEN);
 			break;
 		}
@@ -149,9 +157,9 @@ static void ltq_shutdown_eiu_irq(struct irq_data *d)
 
 	ltq_disable_irq(d);
 	for (i = 0; i < MAX_EIU; i++) {
-		if (d->irq == ltq_eiu_irq[i]) {
+		if (d->hwirq == ltq_eiu_irq[i]) {
 			/* disable */
-			ltq_eiu_w32(ltq_eiu_r32(LTQ_EIU_EXIN_INEN) & ~(1 << i),
+			ltq_eiu_w32(ltq_eiu_r32(LTQ_EIU_EXIN_INEN) & ~BIT(i),
 				LTQ_EIU_EXIN_INEN);
 			break;
 		}
@@ -188,14 +196,15 @@ static void ltq_hw_irqdispatch(int module)
 	if (irq == 0)
 		return;
 
-	/* silicon bug causes only the msb set to 1 to be valid. all
+	/*
+	 * silicon bug causes only the msb set to 1 to be valid. all
 	 * other bits might be bogus
 	 */
 	irq = __fls(irq);
-	do_IRQ((int)irq + INT_NUM_IM0_IRL0 + (INT_NUM_IM_OFFSET * module));
+	do_IRQ((int)irq + MIPS_CPU_IRQ_CASCADE + (INT_NUM_IM_OFFSET * module));
 
 	/* if this is a EBU irq, we need to ack it or get a deadlock */
-	if ((irq == LTQ_ICU_EBU_IRQ) && (module == 0))
+	if ((irq == LTQ_ICU_EBU_IRQ) && (module == 0) && LTQ_EBU_PCC_ISTAT)
 		ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_PCC_ISTAT) | 0x10,
 			LTQ_EBU_PCC_ISTAT);
 }
@@ -216,6 +225,47 @@ static void ltq_hw5_irqdispatch(void)
 	do_IRQ(MIPS_CPU_TIMER_IRQ);
 }
 
+#ifdef CONFIG_MIPS_MT_SMP
+void __init arch_init_ipiirq(int irq, struct irqaction *action)
+{
+	setup_irq(irq, action);
+	irq_set_handler(irq, handle_percpu_irq);
+}
+
+static void ltq_sw0_irqdispatch(void)
+{
+	do_IRQ(MIPS_CPU_IRQ_BASE + MIPS_CPU_IPI_RESCHED_IRQ);
+}
+
+static void ltq_sw1_irqdispatch(void)
+{
+	do_IRQ(MIPS_CPU_IRQ_BASE + MIPS_CPU_IPI_CALL_IRQ);
+}
+static irqreturn_t ipi_resched_interrupt(int irq, void *dev_id)
+{
+	scheduler_ipi();
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t ipi_call_interrupt(int irq, void *dev_id)
+{
+	smp_call_function_interrupt();
+	return IRQ_HANDLED;
+}
+
+static struct irqaction irq_resched = {
+	.handler	= ipi_resched_interrupt,
+	.flags		= IRQF_PERCPU,
+	.name		= "IPI_resched"
+};
+
+static struct irqaction irq_call = {
+	.handler	= ipi_call_interrupt,
+	.flags		= IRQF_PERCPU,
+	.name		= "IPI_call"
+};
+#endif
+
 asmlinkage void plat_irq_dispatch(void)
 {
 	unsigned int pending = read_c0_status() & read_c0_cause() & ST0_IM;
@@ -238,45 +288,75 @@ asmlinkage void plat_irq_dispatch(void)
 	return;
 }
 
+static int icu_map(struct irq_domain *d, unsigned int irq, irq_hw_number_t hw)
+{
+	struct irq_chip *chip = &ltq_irq_type;
+	int i;
+
+	for (i = 0; i < exin_avail; i++)
+		if (hw == ltq_eiu_irq[i])
+			chip = &ltq_eiu_type;
+
+	irq_set_chip_and_handler(hw, chip, handle_level_irq);
+
+	return 0;
+}
+
+static const struct irq_domain_ops irq_domain_ops = {
+	.xlate = irq_domain_xlate_onetwocell,
+	.map = icu_map,
+};
+
 static struct irqaction cascade = {
 	.handler = no_action,
 	.name = "cascade",
 };
 
-void __init arch_init_irq(void)
+int __init icu_of_init(struct device_node *node, struct device_node *parent)
 {
+	struct device_node *eiu_node;
+	struct resource res;
 	int i;
 
-	if (insert_resource(&iomem_resource, &ltq_icu_resource) < 0)
-		panic("Failed to insert icu memory");
+	if (of_address_to_resource(node, 0, &res))
+		panic("Failed to get icu memory range");
 
-	if (request_mem_region(ltq_icu_resource.start,
-			resource_size(&ltq_icu_resource), "icu") < 0)
-		panic("Failed to request icu memory");
+	if (request_mem_region(res.start, resource_size(&res), res.name) < 0)
+		pr_err("Failed to request icu memory");
 
-	ltq_icu_membase = ioremap_nocache(ltq_icu_resource.start,
-				resource_size(&ltq_icu_resource));
+	ltq_icu_membase = ioremap_nocache(res.start, resource_size(&res));
 	if (!ltq_icu_membase)
 		panic("Failed to remap icu memory");
 
-	if (insert_resource(&iomem_resource, &ltq_eiu_resource) < 0)
-		panic("Failed to insert eiu memory");
-
-	if (request_mem_region(ltq_eiu_resource.start,
-			resource_size(&ltq_eiu_resource), "eiu") < 0)
-		panic("Failed to request eiu memory");
-
-	ltq_eiu_membase = ioremap_nocache(ltq_eiu_resource.start,
-				resource_size(&ltq_eiu_resource));
-	if (!ltq_eiu_membase)
-		panic("Failed to remap eiu memory");
+	/* the external interrupts are optional and xway only */
+	eiu_node = of_find_compatible_node(NULL, NULL, "lantiq,eiu");
+	if (eiu_node && of_address_to_resource(eiu_node, 0, &res)) {
+		/* find out how many external irq sources we have */
+		const __be32 *count = of_get_property(node,
+							"lantiq,count",	NULL);
+
+		if (count)
+			exin_avail = *count;
+		if (exin_avail > MAX_EIU)
+			exin_avail = MAX_EIU;
+
+		if (request_mem_region(res.start, resource_size(&res),
+							res.name) < 0)
+			pr_err("Failed to request eiu memory");
+
+		ltq_eiu_membase = ioremap_nocache(res.start,
+							resource_size(&res));
+		if (!ltq_eiu_membase)
+			panic("Failed to remap eiu memory");
+	}
 
-	/* make sure all irqs are turned off by default */
-	for (i = 0; i < 5; i++)
+	/* turn off all irqs by default */
+	for (i = 0; i < 5; i++) {
+		/* make sure all irqs are turned off by default */
 		ltq_icu_w32(0, LTQ_ICU_IM0_IER + (i * LTQ_ICU_OFFSET));
-
-	/* clear all possibly pending interrupts */
-	ltq_icu_w32(~0, LTQ_ICU_IM0_ISR + (i * LTQ_ICU_OFFSET));
+		/* clear all possibly pending interrupts */
+		ltq_icu_w32(~0, LTQ_ICU_IM0_ISR + (i * LTQ_ICU_OFFSET));
+	}
 
 	mips_cpu_irq_init();
 
@@ -293,20 +373,19 @@ void __init arch_init_irq(void)
 		set_vi_handler(7, ltq_hw5_irqdispatch);
 	}
 
-	for (i = INT_NUM_IRQ0;
-		i <= (INT_NUM_IRQ0 + (5 * INT_NUM_IM_OFFSET)); i++)
-		if ((i == LTQ_EIU_IR0) || (i == LTQ_EIU_IR1) ||
-			(i == LTQ_EIU_IR2))
-			irq_set_chip_and_handler(i, &ltq_eiu_type,
-				handle_level_irq);
-		/* EIU3-5 only exist on ar9 and vr9 */
-		else if (((i == LTQ_EIU_IR3) || (i == LTQ_EIU_IR4) ||
-			(i == LTQ_EIU_IR5)) && (ltq_is_ar9() || ltq_is_vr9()))
-			irq_set_chip_and_handler(i, &ltq_eiu_type,
-				handle_level_irq);
-		else
-			irq_set_chip_and_handler(i, &ltq_irq_type,
-				handle_level_irq);
+	irq_domain_add_linear(node, 6 * INT_NUM_IM_OFFSET,
+		&irq_domain_ops, 0);
+
+#if defined(CONFIG_MIPS_MT_SMP)
+	if (cpu_has_vint) {
+		pr_info("Setting up IPI vectored interrupts\n");
+		set_vi_handler(MIPS_CPU_IPI_RESCHED_IRQ, ltq_sw0_irqdispatch);
+		set_vi_handler(MIPS_CPU_IPI_CALL_IRQ, ltq_sw1_irqdispatch);
+	}
+	arch_init_ipiirq(MIPS_CPU_IRQ_BASE + MIPS_CPU_IPI_RESCHED_IRQ,
+		&irq_resched);
+	arch_init_ipiirq(MIPS_CPU_IRQ_BASE + MIPS_CPU_IPI_CALL_IRQ, &irq_call);
+#endif
 
 #if !defined(CONFIG_MIPS_MT_SMP) && !defined(CONFIG_MIPS_MT_SMTC)
 	set_c0_status(IE_IRQ0 | IE_IRQ1 | IE_IRQ2 |
@@ -315,9 +394,23 @@ void __init arch_init_irq(void)
 	set_c0_status(IE_SW0 | IE_SW1 | IE_IRQ0 | IE_IRQ1 |
 		IE_IRQ2 | IE_IRQ3 | IE_IRQ4 | IE_IRQ5);
 #endif
+
+	/* tell oprofile which irq to use */
+	cp0_perfcount_irq = LTQ_PERF_IRQ;
+	return 0;
 }
 
 unsigned int __cpuinit get_c0_compare_int(void)
 {
 	return CP0_LEGACY_COMPARE_IRQ;
 }
+
+static struct of_device_id __initdata of_irq_ids[] = {
+	{ .compatible = "lantiq,icu", .data = icu_of_init },
+	{},
+};
+
+void __init arch_init_irq(void)
+{
+	of_irq_init(of_irq_ids);
+}

arch/mips/lantiq/machtypes.h

@@ -1,20 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
- */
-
-#ifndef _LANTIQ_MACH_H__
-#define _LANTIQ_MACH_H__
-
-#include <asm/mips_machine.h>
-
-enum lantiq_mach_type {
-	LTQ_MACH_GENERIC = 0,
-	LTQ_MACH_EASY50712,	/* Danube evaluation board */
-	LTQ_MACH_EASY50601,	/* Amazon SE evaluation board */
-};
-
-#endif

arch/mips/lantiq/prom.c

@@ -8,6 +8,7 @@
 
 #include <linux/export.h>
 #include <linux/clk.h>
+#include <linux/of_platform.h>
 #include <asm/bootinfo.h>
 #include <asm/time.h>
 
@@ -16,19 +17,15 @@
 #include "prom.h"
 #include "clk.h"
 
-static struct ltq_soc_info soc_info;
-
-unsigned int ltq_get_cpu_ver(void)
-{
-	return soc_info.rev;
-}
-EXPORT_SYMBOL(ltq_get_cpu_ver);
+/* access to the ebu needs to be locked between different drivers */
+DEFINE_SPINLOCK(ebu_lock);
+EXPORT_SYMBOL_GPL(ebu_lock);
 
-unsigned int ltq_get_soc_type(void)
-{
-	return soc_info.type;
-}
-EXPORT_SYMBOL(ltq_get_soc_type);
+/*
+ * this struct is filled by the soc specific detection code and holds
+ * information about the specific soc type, revision and name
+ */
+static struct ltq_soc_info soc_info;
 
 const char *get_system_type(void)
 {
@@ -45,27 +42,62 @@ static void __init prom_init_cmdline(void)
 	char **argv = (char **) KSEG1ADDR(fw_arg1);
 	int i;
 
+	arcs_cmdline[0] = '\0';
+
 	for (i = 0; i < argc; i++) {
-		char *p = (char *)  KSEG1ADDR(argv[i]);
+		char *p = (char *) KSEG1ADDR(argv[i]);
 
-		if (p && *p) {
+		if (CPHYSADDR(p) && *p) {
 			strlcat(arcs_cmdline, p, sizeof(arcs_cmdline));
 			strlcat(arcs_cmdline, " ", sizeof(arcs_cmdline));
 		}
 	}
 }
 
-void __init prom_init(void)
+void __init plat_mem_setup(void)
 {
-	struct clk *clk;
+	ioport_resource.start = IOPORT_RESOURCE_START;
+	ioport_resource.end = IOPORT_RESOURCE_END;
+	iomem_resource.start = IOMEM_RESOURCE_START;
+	iomem_resource.end = IOMEM_RESOURCE_END;
+
+	set_io_port_base((unsigned long) KSEG1);
 
+	/*
+	 * Load the builtin devicetree. This causes the chosen node to be
+	 * parsed resulting in our memory appearing
+	 */
+	__dt_setup_arch(&__dtb_start);
+}
+
+void __init prom_init(void)
+{
+	/* call the soc specific detetcion code and get it to fill soc_info */
 	ltq_soc_detect(&soc_info);
-	clk_init();
-	clk = clk_get(0, "cpu");
-	snprintf(soc_info.sys_type, LTQ_SYS_TYPE_LEN - 1, "%s rev1.%d",
-		soc_info.name, soc_info.rev);
-	clk_put(clk);
+	snprintf(soc_info.sys_type, LTQ_SYS_TYPE_LEN - 1, "%s rev %s",
+		soc_info.name, soc_info.rev_type);
 	soc_info.sys_type[LTQ_SYS_TYPE_LEN - 1] = '\0';
 	pr_info("SoC: %s\n", soc_info.sys_type);
 	prom_init_cmdline();
+
+#if defined(CONFIG_MIPS_MT_SMP)
+	if (register_vsmp_smp_ops())
+		panic("failed to register_vsmp_smp_ops()");
+#endif
 }
+
+int __init plat_of_setup(void)
+{
+	static struct of_device_id of_ids[3];
+
+	if (!of_have_populated_dt())
+		panic("device tree not present");
+
+	strncpy(of_ids[0].compatible, soc_info.compatible,
+		sizeof(of_ids[0].compatible));
+	strncpy(of_ids[1].compatible, "simple-bus",
+		sizeof(of_ids[1].compatible));
+	return of_platform_bus_probe(NULL, of_ids, NULL);
+}
+
+arch_initcall(plat_of_setup);

arch/mips/lantiq/prom.h

@@ -10,16 +10,22 @@
 #define _LTQ_PROM_H__
 
 #define LTQ_SYS_TYPE_LEN	0x100
+#define LTQ_SYS_REV_LEN         0x10
 
 struct ltq_soc_info {
 	unsigned char *name;
 	unsigned int rev;
+	unsigned char rev_type[LTQ_SYS_REV_LEN];
+	unsigned int srev;
 	unsigned int partnum;
 	unsigned int type;
 	unsigned char sys_type[LTQ_SYS_TYPE_LEN];
+	unsigned char *compatible;
 };
 
 extern void ltq_soc_detect(struct ltq_soc_info *i);
-extern void ltq_soc_setup(void);
+extern void ltq_soc_init(void);
+
+extern struct boot_param_header __dtb_start;
 
 #endif

arch/mips/lantiq/setup.c

@@ -1,66 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- * Copyright (C) 2010 John Crispin <blogic@openwrt.org>
- */
-
-#include <linux/kernel.h>
-#include <linux/export.h>
-#include <linux/io.h>
-#include <linux/ioport.h>
-#include <asm/bootinfo.h>
-
-#include <lantiq_soc.h>
-
-#include "machtypes.h"
-#include "devices.h"
-#include "prom.h"
-
-void __init plat_mem_setup(void)
-{
-	/* assume 16M as default incase uboot fails to pass proper ramsize */
-	unsigned long memsize = 16;
-	char **envp = (char **) KSEG1ADDR(fw_arg2);
-
-	ioport_resource.start = IOPORT_RESOURCE_START;
-	ioport_resource.end = IOPORT_RESOURCE_END;
-	iomem_resource.start = IOMEM_RESOURCE_START;
-	iomem_resource.end = IOMEM_RESOURCE_END;
-
-	set_io_port_base((unsigned long) KSEG1);
-
-	while (*envp) {
-		char *e = (char *)KSEG1ADDR(*envp);
-		if (!strncmp(e, "memsize=", 8)) {
-			e += 8;
-			if (strict_strtoul(e, 0, &memsize))
-				pr_warn("bad memsize specified\n");
-		}
-		envp++;
-	}
-	memsize *= 1024 * 1024;
-	add_memory_region(0x00000000, memsize, BOOT_MEM_RAM);
-}
-
-static int __init
-lantiq_setup(void)
-{
-	ltq_soc_setup();
-	mips_machine_setup();
-	return 0;
-}
-
-arch_initcall(lantiq_setup);
-
-static void __init
-lantiq_generic_init(void)
-{
-	/* Nothing to do */
-}
-
-MIPS_MACHINE(LTQ_MACH_GENERIC,
-	     "Generic",
-	     "Generic Lantiq based board",
-	     lantiq_generic_init);

arch/mips/lantiq/xway/Kconfig

@@ -1,23 +0,0 @@
-if SOC_XWAY
-
-menu "MIPS Machine"
-
-config LANTIQ_MACH_EASY50712
-	bool "Easy50712 - Danube"
-	default y
-
-endmenu
-
-endif
-
-if SOC_AMAZON_SE
-
-menu "MIPS Machine"
-
-config LANTIQ_MACH_EASY50601
-	bool "Easy50601 - Amazon SE"
-	default y
-
-endmenu
-
-endif

arch/mips/lantiq/xway/Makefile

@@ -1,7 +1 @@
-obj-y := pmu.o ebu.o reset.o gpio.o gpio_stp.o gpio_ebu.o devices.o dma.o
-
-obj-$(CONFIG_SOC_XWAY) += clk-xway.o prom-xway.o setup-xway.o
-obj-$(CONFIG_SOC_AMAZON_SE) += clk-ase.o prom-ase.o setup-ase.o
-
-obj-$(CONFIG_LANTIQ_MACH_EASY50712) += mach-easy50712.o
-obj-$(CONFIG_LANTIQ_MACH_EASY50601) += mach-easy50601.o
+obj-y := prom.o sysctrl.o clk.o reset.o gpio.o dma.o

arch/mips/lantiq/xway/clk-ase.c

@@ -1,48 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2011 John Crispin <blogic@openwrt.org>
- */
-
-#include <linux/io.h>
-#include <linux/export.h>
-#include <linux/init.h>
-#include <linux/clk.h>
-
-#include <asm/time.h>
-#include <asm/irq.h>
-#include <asm/div64.h>
-
-#include <lantiq_soc.h>
-
-/* cgu registers */
-#define LTQ_CGU_SYS	0x0010
-
-unsigned int ltq_get_io_region_clock(void)
-{
-	return CLOCK_133M;
-}
-EXPORT_SYMBOL(ltq_get_io_region_clock);
-
-unsigned int ltq_get_fpi_bus_clock(int fpi)
-{
-	return CLOCK_133M;
-}
-EXPORT_SYMBOL(ltq_get_fpi_bus_clock);
-
-unsigned int ltq_get_cpu_hz(void)
-{
-	if (ltq_cgu_r32(LTQ_CGU_SYS) & (1 << 5))
-		return CLOCK_266M;
-	else
-		return CLOCK_133M;
-}
-EXPORT_SYMBOL(ltq_get_cpu_hz);
-
-unsigned int ltq_get_fpi_hz(void)
-{
-	return CLOCK_133M;
-}
-EXPORT_SYMBOL(ltq_get_fpi_hz);

arch/mips/lantiq/xway/clk-xway.c

@@ -1,223 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
- */
-
-#include <linux/io.h>
-#include <linux/export.h>
-#include <linux/init.h>
-#include <linux/clk.h>
-
-#include <asm/time.h>
-#include <asm/irq.h>
-#include <asm/div64.h>
-
-#include <lantiq_soc.h>
-
-static unsigned int ltq_ram_clocks[] = {
-	CLOCK_167M, CLOCK_133M, CLOCK_111M, CLOCK_83M };
-#define DDR_HZ ltq_ram_clocks[ltq_cgu_r32(LTQ_CGU_SYS) & 0x3]
-
-#define BASIC_FREQUENCY_1	35328000
-#define BASIC_FREQUENCY_2	36000000
-#define BASIS_REQUENCY_USB	12000000
-
-#define GET_BITS(x, msb, lsb) \
-	(((x) & ((1 << ((msb) + 1)) - 1)) >> (lsb))
-
-#define LTQ_CGU_PLL0_CFG	0x0004
-#define LTQ_CGU_PLL1_CFG	0x0008
-#define LTQ_CGU_PLL2_CFG	0x000C
-#define LTQ_CGU_SYS		0x0010
-#define LTQ_CGU_UPDATE		0x0014
-#define LTQ_CGU_IF_CLK		0x0018
-#define LTQ_CGU_OSC_CON		0x001C
-#define LTQ_CGU_SMD		0x0020
-#define LTQ_CGU_CT1SR		0x0028
-#define LTQ_CGU_CT2SR		0x002C
-#define LTQ_CGU_PCMCR		0x0030
-#define LTQ_CGU_PCI_CR		0x0034
-#define LTQ_CGU_PD_PC		0x0038
-#define LTQ_CGU_FMR		0x003C
-
-#define CGU_PLL0_PHASE_DIVIDER_ENABLE	\
-	(ltq_cgu_r32(LTQ_CGU_PLL0_CFG) & (1 << 31))
-#define CGU_PLL0_BYPASS			\
-	(ltq_cgu_r32(LTQ_CGU_PLL0_CFG) & (1 << 30))
-#define CGU_PLL0_CFG_DSMSEL		\
-	(ltq_cgu_r32(LTQ_CGU_PLL0_CFG) & (1 << 28))
-#define CGU_PLL0_CFG_FRAC_EN		\
-	(ltq_cgu_r32(LTQ_CGU_PLL0_CFG) & (1 << 27))
-#define CGU_PLL1_SRC			\
-	(ltq_cgu_r32(LTQ_CGU_PLL1_CFG) & (1 << 31))
-#define CGU_PLL2_PHASE_DIVIDER_ENABLE	\
-	(ltq_cgu_r32(LTQ_CGU_PLL2_CFG) & (1 << 20))
-#define CGU_SYS_FPI_SEL			(1 << 6)
-#define CGU_SYS_DDR_SEL			0x3
-#define CGU_PLL0_SRC			(1 << 29)
-
-#define CGU_PLL0_CFG_PLLK	GET_BITS(ltq_cgu_r32(LTQ_CGU_PLL0_CFG), 26, 17)
-#define CGU_PLL0_CFG_PLLN	GET_BITS(ltq_cgu_r32(LTQ_CGU_PLL0_CFG), 12, 6)
-#define CGU_PLL0_CFG_PLLM	GET_BITS(ltq_cgu_r32(LTQ_CGU_PLL0_CFG), 5, 2)
-#define CGU_PLL2_SRC		GET_BITS(ltq_cgu_r32(LTQ_CGU_PLL2_CFG), 18, 17)
-#define CGU_PLL2_CFG_INPUT_DIV	GET_BITS(ltq_cgu_r32(LTQ_CGU_PLL2_CFG), 16, 13)
-
-static unsigned int ltq_get_pll0_fdiv(void);
-
-static inline unsigned int get_input_clock(int pll)
-{
-	switch (pll) {
-	case 0:
-		if (ltq_cgu_r32(LTQ_CGU_PLL0_CFG) & CGU_PLL0_SRC)
-			return BASIS_REQUENCY_USB;
-		else if (CGU_PLL0_PHASE_DIVIDER_ENABLE)
-			return BASIC_FREQUENCY_1;
-		else
-			return BASIC_FREQUENCY_2;
-	case 1:
-		if (CGU_PLL1_SRC)
-			return BASIS_REQUENCY_USB;
-		else if (CGU_PLL0_PHASE_DIVIDER_ENABLE)
-			return BASIC_FREQUENCY_1;
-		else
-			return BASIC_FREQUENCY_2;
-	case 2:
-		switch (CGU_PLL2_SRC) {
-		case 0:
-			return ltq_get_pll0_fdiv();
-		case 1:
-			return CGU_PLL2_PHASE_DIVIDER_ENABLE ?
-				BASIC_FREQUENCY_1 :
-				BASIC_FREQUENCY_2;
-		case 2:
-			return BASIS_REQUENCY_USB;
-		}
-	default:
-		return 0;
-	}
-}
-
-static inline unsigned int cal_dsm(int pll, unsigned int num, unsigned int den)
-{
-	u64 res, clock = get_input_clock(pll);
-
-	res = num * clock;
-	do_div(res, den);
-	return res;
-}
-
-static inline unsigned int mash_dsm(int pll, unsigned int M, unsigned int N,
-	unsigned int K)
-{
-	unsigned int num = ((N + 1) << 10) + K;
-	unsigned int den = (M + 1) << 10;
-
-	return cal_dsm(pll, num, den);
-}
-
-static inline unsigned int ssff_dsm_1(int pll, unsigned int M, unsigned int N,
-	unsigned int K)
-{
-	unsigned int num = ((N + 1) << 11) + K + 512;
-	unsigned int den = (M + 1) << 11;
-
-	return cal_dsm(pll, num, den);
-}
-
-static inline unsigned int ssff_dsm_2(int pll, unsigned int M, unsigned int N,
-	unsigned int K)
-{
-	unsigned int num = K >= 512 ?
-		((N + 1) << 12) + K - 512 : ((N + 1) << 12) + K + 3584;
-	unsigned int den = (M + 1) << 12;
-
-	return cal_dsm(pll, num, den);
-}
-
-static inline unsigned int dsm(int pll, unsigned int M, unsigned int N,
-	unsigned int K, unsigned int dsmsel, unsigned int phase_div_en)
-{
-	if (!dsmsel)
-		return mash_dsm(pll, M, N, K);
-	else if (!phase_div_en)
-		return mash_dsm(pll, M, N, K);
-	else
-		return ssff_dsm_2(pll, M, N, K);
-}
-
-static inline unsigned int ltq_get_pll0_fosc(void)
-{
-	if (CGU_PLL0_BYPASS)
-		return get_input_clock(0);
-	else
-		return !CGU_PLL0_CFG_FRAC_EN
-			? dsm(0, CGU_PLL0_CFG_PLLM, CGU_PLL0_CFG_PLLN, 0,
-				CGU_PLL0_CFG_DSMSEL,
-				CGU_PLL0_PHASE_DIVIDER_ENABLE)
-			: dsm(0, CGU_PLL0_CFG_PLLM, CGU_PLL0_CFG_PLLN,
-				CGU_PLL0_CFG_PLLK, CGU_PLL0_CFG_DSMSEL,
-				CGU_PLL0_PHASE_DIVIDER_ENABLE);
-}
-
-static unsigned int ltq_get_pll0_fdiv(void)
-{
-	unsigned int div = CGU_PLL2_CFG_INPUT_DIV + 1;
-
-	return (ltq_get_pll0_fosc() + (div >> 1)) / div;
-}
-
-unsigned int ltq_get_io_region_clock(void)
-{
-	unsigned int ret = ltq_get_pll0_fosc();
-
-	switch (ltq_cgu_r32(LTQ_CGU_PLL2_CFG) & CGU_SYS_DDR_SEL) {
-	default:
-	case 0:
-		return (ret + 1) / 2;
-	case 1:
-		return (ret * 2 + 2) / 5;
-	case 2:
-		return (ret + 1) / 3;
-	case 3:
-		return (ret + 2) / 4;
-	}
-}
-EXPORT_SYMBOL(ltq_get_io_region_clock);
-
-unsigned int ltq_get_fpi_bus_clock(int fpi)
-{
-	unsigned int ret = ltq_get_io_region_clock();
-
-	if ((fpi == 2) && (ltq_cgu_r32(LTQ_CGU_SYS) & CGU_SYS_FPI_SEL))
-		ret >>= 1;
-	return ret;
-}
-EXPORT_SYMBOL(ltq_get_fpi_bus_clock);
-
-unsigned int ltq_get_cpu_hz(void)
-{
-	switch (ltq_cgu_r32(LTQ_CGU_SYS) & 0xc) {
-	case 0:
-		return CLOCK_333M;
-	case 4:
-		return DDR_HZ;
-	case 8:
-		return DDR_HZ << 1;
-	default:
-		return DDR_HZ >> 1;
-	}
-}
-EXPORT_SYMBOL(ltq_get_cpu_hz);
-
-unsigned int ltq_get_fpi_hz(void)
-{
-	unsigned int ddr_clock = DDR_HZ;
-
-	if (ltq_cgu_r32(LTQ_CGU_SYS) & 0x40)
-		return ddr_clock >> 1;
-	return ddr_clock;
-}
-EXPORT_SYMBOL(ltq_get_fpi_hz);

arch/mips/lantiq/xway/clk.c

@@ -0,0 +1,151 @@
+/*
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ *
+ *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
+ */
+
+#include <linux/io.h>
+#include <linux/export.h>
+#include <linux/init.h>
+#include <linux/clk.h>
+
+#include <asm/time.h>
+#include <asm/irq.h>
+#include <asm/div64.h>
+
+#include <lantiq_soc.h>
+
+#include "../clk.h"
+
+static unsigned int ram_clocks[] = {
+	CLOCK_167M, CLOCK_133M, CLOCK_111M, CLOCK_83M };
+#define DDR_HZ ram_clocks[ltq_cgu_r32(CGU_SYS) & 0x3]
+
+/* legacy xway clock */
+#define CGU_SYS			0x10
+
+/* vr9 clock */
+#define CGU_SYS_VR9		0x0c
+#define CGU_IF_CLK_VR9		0x24
+
+unsigned long ltq_danube_fpi_hz(void)
+{
+	unsigned long ddr_clock = DDR_HZ;
+
+	if (ltq_cgu_r32(CGU_SYS) & 0x40)
+		return ddr_clock >> 1;
+	return ddr_clock;
+}
+
+unsigned long ltq_danube_cpu_hz(void)
+{
+	switch (ltq_cgu_r32(CGU_SYS) & 0xc) {
+	case 0:
+		return CLOCK_333M;
+	case 4:
+		return DDR_HZ;
+	case 8:
+		return DDR_HZ << 1;
+	default:
+		return DDR_HZ >> 1;
+	}
+}
+
+unsigned long ltq_ar9_sys_hz(void)
+{
+	if (((ltq_cgu_r32(CGU_SYS) >> 3) & 0x3) == 0x2)
+		return CLOCK_393M;
+	return CLOCK_333M;
+}
+
+unsigned long ltq_ar9_fpi_hz(void)
+{
+	unsigned long sys = ltq_ar9_sys_hz();
+
+	if (ltq_cgu_r32(CGU_SYS) & BIT(0))
+		return sys;
+	return sys >> 1;
+}
+
+unsigned long ltq_ar9_cpu_hz(void)
+{
+	if (ltq_cgu_r32(CGU_SYS) & BIT(2))
+		return ltq_ar9_fpi_hz();
+	else
+		return ltq_ar9_sys_hz();
+}
+
+unsigned long ltq_vr9_cpu_hz(void)
+{
+	unsigned int cpu_sel;
+	unsigned long clk;
+
+	cpu_sel = (ltq_cgu_r32(CGU_SYS_VR9) >> 4) & 0xf;
+
+	switch (cpu_sel) {
+	case 0:
+		clk = CLOCK_600M;
+		break;
+	case 1:
+		clk = CLOCK_500M;
+		break;
+	case 2:
+		clk = CLOCK_393M;
+		break;
+	case 3:
+		clk = CLOCK_333M;
+		break;
+	case 5:
+	case 6:
+		clk = CLOCK_196_608M;
+		break;
+	case 7:
+		clk = CLOCK_167M;
+		break;
+	case 4:
+	case 8:
+	case 9:
+		clk = CLOCK_125M;
+		break;
+	default:
+		clk = 0;
+		break;
+	}
+
+	return clk;
+}
+
+unsigned long ltq_vr9_fpi_hz(void)
+{
+	unsigned int ocp_sel, cpu_clk;
+	unsigned long clk;
+
+	cpu_clk = ltq_vr9_cpu_hz();
+	ocp_sel = ltq_cgu_r32(CGU_SYS_VR9) & 0x3;
+
+	switch (ocp_sel) {
+	case 0:
+		/* OCP ratio 1 */
+		clk = cpu_clk;
+		break;
+	case 2:
+		/* OCP ratio 2 */
+		clk = cpu_clk / 2;
+		break;
+	case 3:
+		/* OCP ratio 2.5 */
+		clk = (cpu_clk * 2) / 5;
+		break;
+	case 4:
+		/* OCP ratio 3 */
+		clk = cpu_clk / 3;
+		break;
+	default:
+		clk = 0;
+		break;
+	}
+
+	return clk;
+}

arch/mips/lantiq/xway/devices.c

@@ -1,119 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
- */
-
-#include <linux/init.h>
-#include <linux/export.h>
-#include <linux/types.h>
-#include <linux/string.h>
-#include <linux/mtd/physmap.h>
-#include <linux/kernel.h>
-#include <linux/reboot.h>
-#include <linux/platform_device.h>
-#include <linux/leds.h>
-#include <linux/etherdevice.h>
-#include <linux/time.h>
-#include <linux/io.h>
-#include <linux/gpio.h>
-
-#include <asm/bootinfo.h>
-#include <asm/irq.h>
-
-#include <lantiq_soc.h>
-#include <lantiq_irq.h>
-#include <lantiq_platform.h>
-
-#include "devices.h"
-
-/* gpio */
-static struct resource ltq_gpio_resource[] = {
-	{
-		.name	= "gpio0",
-		.start  = LTQ_GPIO0_BASE_ADDR,
-		.end    = LTQ_GPIO0_BASE_ADDR + LTQ_GPIO_SIZE - 1,
-		.flags  = IORESOURCE_MEM,
-	}, {
-		.name	= "gpio1",
-		.start  = LTQ_GPIO1_BASE_ADDR,
-		.end    = LTQ_GPIO1_BASE_ADDR + LTQ_GPIO_SIZE - 1,
-		.flags  = IORESOURCE_MEM,
-	}, {
-		.name	= "gpio2",
-		.start  = LTQ_GPIO2_BASE_ADDR,
-		.end    = LTQ_GPIO2_BASE_ADDR + LTQ_GPIO_SIZE - 1,
-		.flags  = IORESOURCE_MEM,
-	}
-};
-
-void __init ltq_register_gpio(void)
-{
-	platform_device_register_simple("ltq_gpio", 0,
-		&ltq_gpio_resource[0], 1);
-	platform_device_register_simple("ltq_gpio", 1,
-		&ltq_gpio_resource[1], 1);
-
-	/* AR9 and VR9 have an extra gpio block */
-	if (ltq_is_ar9() || ltq_is_vr9()) {
-		platform_device_register_simple("ltq_gpio", 2,
-			&ltq_gpio_resource[2], 1);
-	}
-}
-
-/* serial to parallel conversion */
-static struct resource ltq_stp_resource = {
-	.name   = "stp",
-	.start  = LTQ_STP_BASE_ADDR,
-	.end    = LTQ_STP_BASE_ADDR + LTQ_STP_SIZE - 1,
-	.flags  = IORESOURCE_MEM,
-};
-
-void __init ltq_register_gpio_stp(void)
-{
-	platform_device_register_simple("ltq_stp", 0, &ltq_stp_resource, 1);
-}
-
-/* asc ports - amazon se has its own serial mapping */
-static struct resource ltq_ase_asc_resources[] = {
-	{
-		.name	= "asc0",
-		.start  = LTQ_ASC1_BASE_ADDR,
-		.end    = LTQ_ASC1_BASE_ADDR + LTQ_ASC_SIZE - 1,
-		.flags  = IORESOURCE_MEM,
-	},
-	IRQ_RES(tx, LTQ_ASC_ASE_TIR),
-	IRQ_RES(rx, LTQ_ASC_ASE_RIR),
-	IRQ_RES(err, LTQ_ASC_ASE_EIR),
-};
-
-void __init ltq_register_ase_asc(void)
-{
-	platform_device_register_simple("ltq_asc", 0,
-		ltq_ase_asc_resources, ARRAY_SIZE(ltq_ase_asc_resources));
-}
-
-/* ethernet */
-static struct resource ltq_etop_resources = {
-	.name	= "etop",
-	.start	= LTQ_ETOP_BASE_ADDR,
-	.end	= LTQ_ETOP_BASE_ADDR + LTQ_ETOP_SIZE - 1,
-	.flags	= IORESOURCE_MEM,
-};
-
-static struct platform_device ltq_etop = {
-	.name		= "ltq_etop",
-	.resource	= &ltq_etop_resources,
-	.num_resources	= 1,
-};
-
-void __init
-ltq_register_etop(struct ltq_eth_data *eth)
-{
-	if (eth) {
-		ltq_etop.dev.platform_data = eth;
-		platform_device_register(&ltq_etop);
-	}
-}

arch/mips/lantiq/xway/devices.h

@@ -1,20 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
- */
-
-#ifndef _LTQ_DEVICES_XWAY_H__
-#define _LTQ_DEVICES_XWAY_H__
-
-#include "../devices.h"
-#include <linux/phy.h>
-
-extern void ltq_register_gpio(void);
-extern void ltq_register_gpio_stp(void);
-extern void ltq_register_ase_asc(void);
-extern void ltq_register_etop(struct ltq_eth_data *eth);
-
-#endif

arch/mips/lantiq/xway/dma.c

@@ -19,7 +19,8 @@
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/dma-mapping.h>
-#include <linux/export.h>
+#include <linux/module.h>
+#include <linux/clk.h>
 
 #include <lantiq_soc.h>
 #include <xway_dma.h>
@@ -55,13 +56,6 @@
 #define ltq_dma_w32_mask(x, y, z)	ltq_w32_mask(x, y, \
 						ltq_dma_membase + (z))
 
-static struct resource ltq_dma_resource = {
-	.name	= "dma",
-	.start	= LTQ_DMA_BASE_ADDR,
-	.end	= LTQ_DMA_BASE_ADDR + LTQ_DMA_SIZE - 1,
-	.flags  = IORESOURCE_MEM,
-};
-
 static void __iomem *ltq_dma_membase;
 
 void
@@ -215,27 +209,28 @@ ltq_dma_init_port(int p)
 }
 EXPORT_SYMBOL_GPL(ltq_dma_init_port);
 
-int __init
-ltq_dma_init(void)
+static int __devinit
+ltq_dma_init(struct platform_device *pdev)
 {
+	struct clk *clk;
+	struct resource *res;
 	int i;
 
-	/* insert and request the memory region */
-	if (insert_resource(&iomem_resource, &ltq_dma_resource) < 0)
-		panic("Failed to insert dma memory");
-
-	if (request_mem_region(ltq_dma_resource.start,
-			resource_size(&ltq_dma_resource), "dma") < 0)
-		panic("Failed to request dma memory");
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		panic("Failed to get dma resource");
 
 	/* remap dma register range */
-	ltq_dma_membase = ioremap_nocache(ltq_dma_resource.start,
-				resource_size(&ltq_dma_resource));
+	ltq_dma_membase = devm_request_and_ioremap(&pdev->dev, res);
 	if (!ltq_dma_membase)
-		panic("Failed to remap dma memory");
+		panic("Failed to remap dma resource");
 
 	/* power up and reset the dma engine */
-	ltq_pmu_enable(PMU_DMA);
+	clk = clk_get(&pdev->dev, NULL);
+	if (IS_ERR(clk))
+		panic("Failed to get dma clock");
+
+	clk_enable(clk);
 	ltq_dma_w32_mask(0, DMA_RESET, LTQ_DMA_CTRL);
 
 	/* disable all interrupts */
@@ -248,7 +243,29 @@ ltq_dma_init(void)
 		ltq_dma_w32(DMA_POLL | DMA_CLK_DIV4, LTQ_DMA_CPOLL);
 		ltq_dma_w32_mask(DMA_CHAN_ON, 0, LTQ_DMA_CCTRL);
 	}
+	dev_info(&pdev->dev, "init done\n");
 	return 0;
 }
 
-postcore_initcall(ltq_dma_init);
+static const struct of_device_id dma_match[] = {
+	{ .compatible = "lantiq,dma-xway" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, dma_match);
+
+static struct platform_driver dma_driver = {
+	.probe = ltq_dma_init,
+	.driver = {
+		.name = "dma-xway",
+		.owner = THIS_MODULE,
+		.of_match_table = dma_match,
+	},
+};
+
+int __init
+dma_init(void)
+{
+	return platform_driver_register(&dma_driver);
+}
+
+postcore_initcall(dma_init);

arch/mips/lantiq/xway/ebu.c

@@ -1,52 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  EBU - the external bus unit attaches PCI, NOR and NAND
- *
- *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/ioport.h>
-
-#include <lantiq_soc.h>
-
-/* all access to the ebu must be locked */
-DEFINE_SPINLOCK(ebu_lock);
-EXPORT_SYMBOL_GPL(ebu_lock);
-
-static struct resource ltq_ebu_resource = {
-	.name	= "ebu",
-	.start	= LTQ_EBU_BASE_ADDR,
-	.end	= LTQ_EBU_BASE_ADDR + LTQ_EBU_SIZE - 1,
-	.flags	= IORESOURCE_MEM,
-};
-
-/* remapped base addr of the clock unit and external bus unit */
-void __iomem *ltq_ebu_membase;
-
-static int __init lantiq_ebu_init(void)
-{
-	/* insert and request the memory region */
-	if (insert_resource(&iomem_resource, &ltq_ebu_resource) < 0)
-		panic("Failed to insert ebu memory");
-
-	if (request_mem_region(ltq_ebu_resource.start,
-			resource_size(&ltq_ebu_resource), "ebu") < 0)
-		panic("Failed to request ebu memory");
-
-	/* remap ebu register range */
-	ltq_ebu_membase = ioremap_nocache(ltq_ebu_resource.start,
-				resource_size(&ltq_ebu_resource));
-	if (!ltq_ebu_membase)
-		panic("Failed to remap ebu memory");
-
-	/* make sure to unprotect the memory region where flash is located */
-	ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_BUSCON0) & ~EBU_WRDIS, LTQ_EBU_BUSCON0);
-	return 0;
-}
-
-postcore_initcall(lantiq_ebu_init);

arch/mips/lantiq/xway/gpio.c

@@ -36,18 +36,6 @@ struct ltq_gpio {
 
 static struct ltq_gpio ltq_gpio_port[MAX_PORTS];
 
-int gpio_to_irq(unsigned int gpio)
-{
-	return -EINVAL;
-}
-EXPORT_SYMBOL(gpio_to_irq);
-
-int irq_to_gpio(unsigned int gpio)
-{
-	return -EINVAL;
-}
-EXPORT_SYMBOL(irq_to_gpio);
-
 int ltq_gpio_request(unsigned int pin, unsigned int alt0,
 	unsigned int alt1, unsigned int dir, const char *name)
 {

arch/mips/lantiq/xway/gpio_ebu.c

@@ -1,126 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
- */
-
-#include <linux/init.h>
-#include <linux/export.h>
-#include <linux/types.h>
-#include <linux/platform_device.h>
-#include <linux/mutex.h>
-#include <linux/gpio.h>
-#include <linux/io.h>
-
-#include <lantiq_soc.h>
-
-/*
- * By attaching hardware latches to the EBU it is possible to create output
- * only gpios. This driver configures a special memory address, which when
- * written to outputs 16 bit to the latches.
- */
-
-#define LTQ_EBU_BUSCON	0x1e7ff		/* 16 bit access, slowest timing */
-#define LTQ_EBU_WP	0x80000000	/* write protect bit */
-
-/* we keep a shadow value of the last value written to the ebu */
-static int ltq_ebu_gpio_shadow = 0x0;
-static void __iomem *ltq_ebu_gpio_membase;
-
-static void ltq_ebu_apply(void)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&ebu_lock, flags);
-	ltq_ebu_w32(LTQ_EBU_BUSCON, LTQ_EBU_BUSCON1);
-	*((__u16 *)ltq_ebu_gpio_membase) = ltq_ebu_gpio_shadow;
-	ltq_ebu_w32(LTQ_EBU_BUSCON | LTQ_EBU_WP, LTQ_EBU_BUSCON1);
-	spin_unlock_irqrestore(&ebu_lock, flags);
-}
-
-static void ltq_ebu_set(struct gpio_chip *chip, unsigned offset, int value)
-{
-	if (value)
-		ltq_ebu_gpio_shadow |= (1 << offset);
-	else
-		ltq_ebu_gpio_shadow &= ~(1 << offset);
-	ltq_ebu_apply();
-}
-
-static int ltq_ebu_direction_output(struct gpio_chip *chip, unsigned offset,
-	int value)
-{
-	ltq_ebu_set(chip, offset, value);
-
-	return 0;
-}
-
-static struct gpio_chip ltq_ebu_chip = {
-	.label = "ltq_ebu",
-	.direction_output = ltq_ebu_direction_output,
-	.set = ltq_ebu_set,
-	.base = 72,
-	.ngpio = 16,
-	.can_sleep = 1,
-	.owner = THIS_MODULE,
-};
-
-static int ltq_ebu_probe(struct platform_device *pdev)
-{
-	int ret = 0;
-	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-
-	if (!res) {
-		dev_err(&pdev->dev, "failed to get memory resource\n");
-		return -ENOENT;
-	}
-
-	res = devm_request_mem_region(&pdev->dev, res->start,
-		resource_size(res), dev_name(&pdev->dev));
-	if (!res) {
-		dev_err(&pdev->dev, "failed to request memory resource\n");
-		return -EBUSY;
-	}
-
-	ltq_ebu_gpio_membase = devm_ioremap_nocache(&pdev->dev, res->start,
-		resource_size(res));
-	if (!ltq_ebu_gpio_membase) {
-		dev_err(&pdev->dev, "Failed to ioremap mem region\n");
-		return -ENOMEM;
-	}
-
-	/* grab the default shadow value passed form the platform code */
-	ltq_ebu_gpio_shadow = (unsigned int) pdev->dev.platform_data;
-
-	/* tell the ebu controller which memory address we will be using */
-	ltq_ebu_w32(pdev->resource->start | 0x1, LTQ_EBU_ADDRSEL1);
-
-	/* write protect the region */
-	ltq_ebu_w32(LTQ_EBU_BUSCON | LTQ_EBU_WP, LTQ_EBU_BUSCON1);
-
-	ret = gpiochip_add(&ltq_ebu_chip);
-	if (!ret)
-		ltq_ebu_apply();
-	return ret;
-}
-
-static struct platform_driver ltq_ebu_driver = {
-	.probe = ltq_ebu_probe,
-	.driver = {
-		.name = "ltq_ebu",
-		.owner = THIS_MODULE,
-	},
-};
-
-static int __init ltq_ebu_init(void)
-{
-	int ret = platform_driver_register(&ltq_ebu_driver);
-
-	if (ret)
-		pr_info("ltq_ebu : Error registering platfom driver!");
-	return ret;
-}
-
-postcore_initcall(ltq_ebu_init);

arch/mips/lantiq/xway/gpio_stp.c

@@ -1,157 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2007 John Crispin <blogic@openwrt.org>
- *
- */
-
-#include <linux/slab.h>
-#include <linux/init.h>
-#include <linux/export.h>
-#include <linux/types.h>
-#include <linux/platform_device.h>
-#include <linux/mutex.h>
-#include <linux/io.h>
-#include <linux/gpio.h>
-
-#include <lantiq_soc.h>
-
-#define LTQ_STP_CON0		0x00
-#define LTQ_STP_CON1		0x04
-#define LTQ_STP_CPU0		0x08
-#define LTQ_STP_CPU1		0x0C
-#define LTQ_STP_AR		0x10
-
-#define LTQ_STP_CON_SWU		(1 << 31)
-#define LTQ_STP_2HZ		0
-#define LTQ_STP_4HZ		(1 << 23)
-#define LTQ_STP_8HZ		(2 << 23)
-#define LTQ_STP_10HZ		(3 << 23)
-#define LTQ_STP_SPEED_MASK	(0xf << 23)
-#define LTQ_STP_UPD_FPI		(1 << 31)
-#define LTQ_STP_UPD_MASK	(3 << 30)
-#define LTQ_STP_ADSL_SRC	(3 << 24)
-
-#define LTQ_STP_GROUP0		(1 << 0)
-
-#define LTQ_STP_RISING		0
-#define LTQ_STP_FALLING		(1 << 26)
-#define LTQ_STP_EDGE_MASK	(1 << 26)
-
-#define ltq_stp_r32(reg)	__raw_readl(ltq_stp_membase + reg)
-#define ltq_stp_w32(val, reg)	__raw_writel(val, ltq_stp_membase + reg)
-#define ltq_stp_w32_mask(clear, set, reg) \
-		ltq_w32((ltq_r32(ltq_stp_membase + reg) & ~(clear)) | (set), \
-		ltq_stp_membase + (reg))
-
-static int ltq_stp_shadow = 0xffff;
-static void __iomem *ltq_stp_membase;
-
-static void ltq_stp_set(struct gpio_chip *chip, unsigned offset, int value)
-{
-	if (value)
-		ltq_stp_shadow |= (1 << offset);
-	else
-		ltq_stp_shadow &= ~(1 << offset);
-	ltq_stp_w32(ltq_stp_shadow, LTQ_STP_CPU0);
-}
-
-static int ltq_stp_direction_output(struct gpio_chip *chip, unsigned offset,
-	int value)
-{
-	ltq_stp_set(chip, offset, value);
-
-	return 0;
-}
-
-static struct gpio_chip ltq_stp_chip = {
-	.label = "ltq_stp",
-	.direction_output = ltq_stp_direction_output,
-	.set = ltq_stp_set,
-	.base = 48,
-	.ngpio = 24,
-	.can_sleep = 1,
-	.owner = THIS_MODULE,
-};
-
-static int ltq_stp_hw_init(void)
-{
-	/* the 3 pins used to control the external stp */
-	ltq_gpio_request(4, 1, 0, 1, "stp-st");
-	ltq_gpio_request(5, 1, 0, 1, "stp-d");
-	ltq_gpio_request(6, 1, 0, 1, "stp-sh");
-
-	/* sane defaults */
-	ltq_stp_w32(0, LTQ_STP_AR);
-	ltq_stp_w32(0, LTQ_STP_CPU0);
-	ltq_stp_w32(0, LTQ_STP_CPU1);
-	ltq_stp_w32(LTQ_STP_CON_SWU, LTQ_STP_CON0);
-	ltq_stp_w32(0, LTQ_STP_CON1);
-
-	/* rising or falling edge */
-	ltq_stp_w32_mask(LTQ_STP_EDGE_MASK, LTQ_STP_FALLING, LTQ_STP_CON0);
-
-	/* per default stp 15-0 are set */
-	ltq_stp_w32_mask(0, LTQ_STP_GROUP0, LTQ_STP_CON1);
-
-	/* stp are update periodically by the FPI bus */
-	ltq_stp_w32_mask(LTQ_STP_UPD_MASK, LTQ_STP_UPD_FPI, LTQ_STP_CON1);
-
-	/* set stp update speed */
-	ltq_stp_w32_mask(LTQ_STP_SPEED_MASK, LTQ_STP_8HZ, LTQ_STP_CON1);
-
-	/* tell the hardware that pin (led) 0 and 1 are controlled
-	 *  by the dsl arc
-	 */
-	ltq_stp_w32_mask(0, LTQ_STP_ADSL_SRC, LTQ_STP_CON0);
-
-	ltq_pmu_enable(PMU_LED);
-	return 0;
-}
-
-static int __devinit ltq_stp_probe(struct platform_device *pdev)
-{
-	struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	int ret = 0;
-
-	if (!res)
-		return -ENOENT;
-	res = devm_request_mem_region(&pdev->dev, res->start,
-		resource_size(res), dev_name(&pdev->dev));
-	if (!res) {
-		dev_err(&pdev->dev, "failed to request STP memory\n");
-		return -EBUSY;
-	}
-	ltq_stp_membase = devm_ioremap_nocache(&pdev->dev, res->start,
-		resource_size(res));
-	if (!ltq_stp_membase) {
-		dev_err(&pdev->dev, "failed to remap STP memory\n");
-		return -ENOMEM;
-	}
-	ret = gpiochip_add(&ltq_stp_chip);
-	if (!ret)
-		ret = ltq_stp_hw_init();
-
-	return ret;
-}
-
-static struct platform_driver ltq_stp_driver = {
-	.probe = ltq_stp_probe,
-	.driver = {
-		.name = "ltq_stp",
-		.owner = THIS_MODULE,
-	},
-};
-
-int __init ltq_stp_init(void)
-{
-	int ret = platform_driver_register(&ltq_stp_driver);
-
-	if (ret)
-		pr_info("ltq_stp: error registering platfom driver");
-	return ret;
-}
-
-postcore_initcall(ltq_stp_init);

arch/mips/lantiq/xway/mach-easy50601.c

@@ -1,57 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/input.h>
-
-#include <lantiq.h>
-
-#include "../machtypes.h"
-#include "devices.h"
-
-static struct mtd_partition easy50601_partitions[] = {
-	{
-		.name	= "uboot",
-		.offset	= 0x0,
-		.size	= 0x10000,
-	},
-	{
-		.name	= "uboot_env",
-		.offset	= 0x10000,
-		.size	= 0x10000,
-	},
-	{
-		.name	= "linux",
-		.offset	= 0x20000,
-		.size	= 0xE0000,
-	},
-	{
-		.name	= "rootfs",
-		.offset	= 0x100000,
-		.size	= 0x300000,
-	},
-};
-
-static struct physmap_flash_data easy50601_flash_data = {
-	.nr_parts	= ARRAY_SIZE(easy50601_partitions),
-	.parts		= easy50601_partitions,
-};
-
-static void __init easy50601_init(void)
-{
-	ltq_register_nor(&easy50601_flash_data);
-}
-
-MIPS_MACHINE(LTQ_MACH_EASY50601,
-			"EASY50601",
-			"EASY50601 Eval Board",
-			easy50601_init);

arch/mips/lantiq/xway/mach-easy50712.c

@@ -1,74 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/input.h>
-#include <linux/phy.h>
-
-#include <lantiq_soc.h>
-#include <irq.h>
-
-#include "../machtypes.h"
-#include "devices.h"
-
-static struct mtd_partition easy50712_partitions[] = {
-	{
-		.name	= "uboot",
-		.offset	= 0x0,
-		.size	= 0x10000,
-	},
-	{
-		.name	= "uboot_env",
-		.offset	= 0x10000,
-		.size	= 0x10000,
-	},
-	{
-		.name	= "linux",
-		.offset	= 0x20000,
-		.size	= 0xe0000,
-	},
-	{
-		.name	= "rootfs",
-		.offset	= 0x100000,
-		.size	= 0x300000,
-	},
-};
-
-static struct physmap_flash_data easy50712_flash_data = {
-	.nr_parts	= ARRAY_SIZE(easy50712_partitions),
-	.parts		= easy50712_partitions,
-};
-
-static struct ltq_pci_data ltq_pci_data = {
-	.clock	= PCI_CLOCK_INT,
-	.gpio	= PCI_GNT1 | PCI_REQ1,
-	.irq	= {
-		[14] = INT_NUM_IM0_IRL0 + 22,
-	},
-};
-
-static struct ltq_eth_data ltq_eth_data = {
-	.mii_mode = PHY_INTERFACE_MODE_MII,
-};
-
-static void __init easy50712_init(void)
-{
-	ltq_register_gpio_stp();
-	ltq_register_nor(&easy50712_flash_data);
-	ltq_register_pci(&ltq_pci_data);
-	ltq_register_etop(&ltq_eth_data);
-}
-
-MIPS_MACHINE(LTQ_MACH_EASY50712,
-	     "EASY50712",
-	     "EASY50712 Eval Board",
-	      easy50712_init);

arch/mips/lantiq/xway/pmu.c

@@ -1,69 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/ioport.h>
-
-#include <lantiq_soc.h>
-
-/* PMU - the power management unit allows us to turn part of the core
- * on and off
- */
-
-/* the enable / disable registers */
-#define LTQ_PMU_PWDCR	0x1C
-#define LTQ_PMU_PWDSR	0x20
-
-#define ltq_pmu_w32(x, y)	ltq_w32((x), ltq_pmu_membase + (y))
-#define ltq_pmu_r32(x)		ltq_r32(ltq_pmu_membase + (x))
-
-static struct resource ltq_pmu_resource = {
-	.name	= "pmu",
-	.start	= LTQ_PMU_BASE_ADDR,
-	.end	= LTQ_PMU_BASE_ADDR + LTQ_PMU_SIZE - 1,
-	.flags	= IORESOURCE_MEM,
-};
-
-static void __iomem *ltq_pmu_membase;
-
-void ltq_pmu_enable(unsigned int module)
-{
-	int err = 1000000;
-
-	ltq_pmu_w32(ltq_pmu_r32(LTQ_PMU_PWDCR) & ~module, LTQ_PMU_PWDCR);
-	do {} while (--err && (ltq_pmu_r32(LTQ_PMU_PWDSR) & module));
-
-	if (!err)
-		panic("activating PMU module failed!");
-}
-EXPORT_SYMBOL(ltq_pmu_enable);
-
-void ltq_pmu_disable(unsigned int module)
-{
-	ltq_pmu_w32(ltq_pmu_r32(LTQ_PMU_PWDCR) | module, LTQ_PMU_PWDCR);
-}
-EXPORT_SYMBOL(ltq_pmu_disable);
-
-int __init ltq_pmu_init(void)
-{
-	if (insert_resource(&iomem_resource, &ltq_pmu_resource) < 0)
-		panic("Failed to insert pmu memory");
-
-	if (request_mem_region(ltq_pmu_resource.start,
-			resource_size(&ltq_pmu_resource), "pmu") < 0)
-		panic("Failed to request pmu memory");
-
-	ltq_pmu_membase = ioremap_nocache(ltq_pmu_resource.start,
-				resource_size(&ltq_pmu_resource));
-	if (!ltq_pmu_membase)
-		panic("Failed to remap pmu memory");
-	return 0;
-}
-
-core_initcall(ltq_pmu_init);

arch/mips/lantiq/xway/prom-ase.c

@@ -1,39 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
- */
-
-#include <linux/export.h>
-#include <linux/clk.h>
-#include <asm/bootinfo.h>
-#include <asm/time.h>
-
-#include <lantiq_soc.h>
-
-#include "../prom.h"
-
-#define SOC_AMAZON_SE	"Amazon_SE"
-
-#define PART_SHIFT	12
-#define PART_MASK	0x0FFFFFFF
-#define REV_SHIFT	28
-#define REV_MASK	0xF0000000
-
-void __init ltq_soc_detect(struct ltq_soc_info *i)
-{
-	i->partnum = (ltq_r32(LTQ_MPS_CHIPID) & PART_MASK) >> PART_SHIFT;
-	i->rev = (ltq_r32(LTQ_MPS_CHIPID) & REV_MASK) >> REV_SHIFT;
-	switch (i->partnum) {
-	case SOC_ID_AMAZON_SE:
-		i->name = SOC_AMAZON_SE;
-		i->type = SOC_TYPE_AMAZON_SE;
-		break;
-
-	default:
-		unreachable();
-		break;
-	}
-}

arch/mips/lantiq/xway/prom-xway.c

@@ -1,54 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
- */
-
-#include <linux/export.h>
-#include <linux/clk.h>
-#include <asm/bootinfo.h>
-#include <asm/time.h>
-
-#include <lantiq_soc.h>
-
-#include "../prom.h"
-
-#define SOC_DANUBE	"Danube"
-#define SOC_TWINPASS	"Twinpass"
-#define SOC_AR9		"AR9"
-
-#define PART_SHIFT	12
-#define PART_MASK	0x0FFFFFFF
-#define REV_SHIFT	28
-#define REV_MASK	0xF0000000
-
-void __init ltq_soc_detect(struct ltq_soc_info *i)
-{
-	i->partnum = (ltq_r32(LTQ_MPS_CHIPID) & PART_MASK) >> PART_SHIFT;
-	i->rev = (ltq_r32(LTQ_MPS_CHIPID) & REV_MASK) >> REV_SHIFT;
-	switch (i->partnum) {
-	case SOC_ID_DANUBE1:
-	case SOC_ID_DANUBE2:
-		i->name = SOC_DANUBE;
-		i->type = SOC_TYPE_DANUBE;
-		break;
-
-	case SOC_ID_TWINPASS:
-		i->name = SOC_TWINPASS;
-		i->type = SOC_TYPE_DANUBE;
-		break;
-
-	case SOC_ID_ARX188:
-	case SOC_ID_ARX168:
-	case SOC_ID_ARX182:
-		i->name = SOC_AR9;
-		i->type = SOC_TYPE_AR9;
-		break;
-
-	default:
-		unreachable();
-		break;
-	}
-}

arch/mips/lantiq/xway/prom.c

@@ -0,0 +1,115 @@
+/*
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ *
+ *  Copyright (C) 2010 John Crispin <blogic@openwrt.org>
+ */
+
+#include <linux/export.h>
+#include <linux/clk.h>
+#include <asm/bootinfo.h>
+#include <asm/time.h>
+
+#include <lantiq_soc.h>
+
+#include "../prom.h"
+
+#define SOC_DANUBE	"Danube"
+#define SOC_TWINPASS	"Twinpass"
+#define SOC_AMAZON_SE	"Amazon_SE"
+#define SOC_AR9		"AR9"
+#define SOC_GR9		"GR9"
+#define SOC_VR9		"VR9"
+
+#define COMP_DANUBE	"lantiq,danube"
+#define COMP_TWINPASS	"lantiq,twinpass"
+#define COMP_AMAZON_SE	"lantiq,ase"
+#define COMP_AR9	"lantiq,ar9"
+#define COMP_GR9	"lantiq,gr9"
+#define COMP_VR9	"lantiq,vr9"
+
+#define PART_SHIFT	12
+#define PART_MASK	0x0FFFFFFF
+#define REV_SHIFT	28
+#define REV_MASK	0xF0000000
+
+void __init ltq_soc_detect(struct ltq_soc_info *i)
+{
+	i->partnum = (ltq_r32(LTQ_MPS_CHIPID) & PART_MASK) >> PART_SHIFT;
+	i->rev = (ltq_r32(LTQ_MPS_CHIPID) & REV_MASK) >> REV_SHIFT;
+	sprintf(i->rev_type, "1.%d", i->rev);
+	switch (i->partnum) {
+	case SOC_ID_DANUBE1:
+	case SOC_ID_DANUBE2:
+		i->name = SOC_DANUBE;
+		i->type = SOC_TYPE_DANUBE;
+		i->compatible = COMP_DANUBE;
+		break;
+
+	case SOC_ID_TWINPASS:
+		i->name = SOC_TWINPASS;
+		i->type = SOC_TYPE_DANUBE;
+		i->compatible = COMP_TWINPASS;
+		break;
+
+	case SOC_ID_ARX188:
+	case SOC_ID_ARX168_1:
+	case SOC_ID_ARX168_2:
+	case SOC_ID_ARX182:
+		i->name = SOC_AR9;
+		i->type = SOC_TYPE_AR9;
+		i->compatible = COMP_AR9;
+		break;
+
+	case SOC_ID_GRX188:
+	case SOC_ID_GRX168:
+		i->name = SOC_GR9;
+		i->type = SOC_TYPE_AR9;
+		i->compatible = COMP_GR9;
+		break;
+
+	case SOC_ID_AMAZON_SE_1:
+	case SOC_ID_AMAZON_SE_2:
+#ifdef CONFIG_PCI
+		panic("ase is only supported for non pci kernels");
+#endif
+		i->name = SOC_AMAZON_SE;
+		i->type = SOC_TYPE_AMAZON_SE;
+		i->compatible = COMP_AMAZON_SE;
+		break;
+
+	case SOC_ID_VRX282:
+	case SOC_ID_VRX268:
+	case SOC_ID_VRX288:
+		i->name = SOC_VR9;
+		i->type = SOC_TYPE_VR9;
+		i->compatible = COMP_VR9;
+		break;
+
+	case SOC_ID_GRX268:
+	case SOC_ID_GRX288:
+		i->name = SOC_GR9;
+		i->type = SOC_TYPE_VR9;
+		i->compatible = COMP_GR9;
+		break;
+
+	case SOC_ID_VRX268_2:
+	case SOC_ID_VRX288_2:
+		i->name = SOC_VR9;
+		i->type = SOC_TYPE_VR9_2;
+		i->compatible = COMP_VR9;
+		break;
+
+	case SOC_ID_GRX282_2:
+	case SOC_ID_GRX288_2:
+		i->name = SOC_GR9;
+		i->type = SOC_TYPE_VR9_2;
+		i->compatible = COMP_GR9;
+		break;
+
+	default:
+		unreachable();
+		break;
+	}
+}

arch/mips/lantiq/xway/reset.c

@@ -11,26 +11,31 @@
 #include <linux/ioport.h>
 #include <linux/pm.h>
 #include <linux/export.h>
+#include <linux/delay.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+
 #include <asm/reboot.h>
 
 #include <lantiq_soc.h>
 
+#include "../prom.h"
+
 #define ltq_rcu_w32(x, y)	ltq_w32((x), ltq_rcu_membase + (y))
 #define ltq_rcu_r32(x)		ltq_r32(ltq_rcu_membase + (x))
 
-/* register definitions */
-#define LTQ_RCU_RST		0x0010
-#define LTQ_RCU_RST_ALL		0x40000000
-
-#define LTQ_RCU_RST_STAT	0x0014
-#define LTQ_RCU_STAT_SHIFT	26
+/* reset request register */
+#define RCU_RST_REQ		0x0010
+/* reset status register */
+#define RCU_RST_STAT		0x0014
 
-static struct resource ltq_rcu_resource = {
-	.name   = "rcu",
-	.start  = LTQ_RCU_BASE_ADDR,
-	.end    = LTQ_RCU_BASE_ADDR + LTQ_RCU_SIZE - 1,
-	.flags  = IORESOURCE_MEM,
-};
+/* reboot bit */
+#define RCU_RD_SRST		BIT(30)
+/* reset cause */
+#define RCU_STAT_SHIFT		26
+/* boot selection */
+#define RCU_BOOT_SEL_SHIFT	26
+#define RCU_BOOT_SEL_MASK	0x7
 
 /* remapped base addr of the reset control unit */
 static void __iomem *ltq_rcu_membase;
@@ -38,48 +43,64 @@ static void __iomem *ltq_rcu_membase;
 /* This function is used by the watchdog driver */
 int ltq_reset_cause(void)
 {
-	u32 val = ltq_rcu_r32(LTQ_RCU_RST_STAT);
-	return val >> LTQ_RCU_STAT_SHIFT;
+	u32 val = ltq_rcu_r32(RCU_RST_STAT);
+	return val >> RCU_STAT_SHIFT;
 }
 EXPORT_SYMBOL_GPL(ltq_reset_cause);
 
+/* allow platform code to find out what source we booted from */
+unsigned char ltq_boot_select(void)
+{
+	u32 val = ltq_rcu_r32(RCU_RST_STAT);
+	return (val >> RCU_BOOT_SEL_SHIFT) & RCU_BOOT_SEL_MASK;
+}
+
+/* reset a io domain for u micro seconds */
+void ltq_reset_once(unsigned int module, ulong u)
+{
+	ltq_rcu_w32(ltq_rcu_r32(RCU_RST_REQ) | module, RCU_RST_REQ);
+	udelay(u);
+	ltq_rcu_w32(ltq_rcu_r32(RCU_RST_REQ) & ~module, RCU_RST_REQ);
+}
+
 static void ltq_machine_restart(char *command)
 {
-	pr_notice("System restart\n");
 	local_irq_disable();
-	ltq_rcu_w32(ltq_rcu_r32(LTQ_RCU_RST) | LTQ_RCU_RST_ALL, LTQ_RCU_RST);
+	ltq_rcu_w32(ltq_rcu_r32(RCU_RST_REQ) | RCU_RD_SRST, RCU_RST_REQ);
 	unreachable();
 }
 
 static void ltq_machine_halt(void)
 {
-	pr_notice("System halted.\n");
 	local_irq_disable();
 	unreachable();
 }
 
 static void ltq_machine_power_off(void)
 {
-	pr_notice("Please turn off the power now.\n");
 	local_irq_disable();
 	unreachable();
 }
 
 static int __init mips_reboot_setup(void)
 {
-	/* insert and request the memory region */
-	if (insert_resource(&iomem_resource, &ltq_rcu_resource) < 0)
-		panic("Failed to insert rcu memory");
+	struct resource res;
+	struct device_node *np =
+		of_find_compatible_node(NULL, NULL, "lantiq,rcu-xway");
+
+	/* check if all the reset register range is available */
+	if (!np)
+		panic("Failed to load reset resources from devicetree");
+
+	if (of_address_to_resource(np, 0, &res))
+		panic("Failed to get rcu memory range");
 
-	if (request_mem_region(ltq_rcu_resource.start,
-			resource_size(&ltq_rcu_resource), "rcu") < 0)
-		panic("Failed to request rcu memory");
+	if (request_mem_region(res.start, resource_size(&res), res.name) < 0)
+		pr_err("Failed to request rcu memory");
 
-	/* remap rcu register range */
-	ltq_rcu_membase = ioremap_nocache(ltq_rcu_resource.start,
-				resource_size(&ltq_rcu_resource));
+	ltq_rcu_membase = ioremap_nocache(res.start, resource_size(&res));
 	if (!ltq_rcu_membase)
-		panic("Failed to remap rcu memory");
+		panic("Failed to remap core memory");
 
 	_machine_restart = ltq_machine_restart;
 	_machine_halt = ltq_machine_halt;

arch/mips/lantiq/xway/setup-ase.c

@@ -1,19 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2011 John Crispin <blogic@openwrt.org>
- */
-
-#include <lantiq_soc.h>
-
-#include "../prom.h"
-#include "devices.h"
-
-void __init ltq_soc_setup(void)
-{
-	ltq_register_ase_asc();
-	ltq_register_gpio();
-	ltq_register_wdt();
-}

arch/mips/lantiq/xway/setup-xway.c

@@ -1,20 +0,0 @@
-/*
- *  This program is free software; you can redistribute it and/or modify it
- *  under the terms of the GNU General Public License version 2 as published
- *  by the Free Software Foundation.
- *
- *  Copyright (C) 2011 John Crispin <blogic@openwrt.org>
- */
-
-#include <lantiq_soc.h>
-
-#include "../prom.h"
-#include "devices.h"
-
-void __init ltq_soc_setup(void)
-{
-	ltq_register_asc(0);
-	ltq_register_asc(1);
-	ltq_register_gpio();
-	ltq_register_wdt();
-}

arch/mips/lantiq/xway/sysctrl.c

@@ -0,0 +1,371 @@
+/*
+ *  This program is free software; you can redistribute it and/or modify it
+ *  under the terms of the GNU General Public License version 2 as published
+ *  by the Free Software Foundation.
+ *
+ *  Copyright (C) 2011-2012 John Crispin <blogic@openwrt.org>
+ */
+
+#include <linux/ioport.h>
+#include <linux/export.h>
+#include <linux/clkdev.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+
+#include <lantiq_soc.h>
+
+#include "../clk.h"
+#include "../prom.h"
+
+/* clock control register */
+#define CGU_IFCCR	0x0018
+/* system clock register */
+#define CGU_SYS		0x0010
+/* pci control register */
+#define CGU_PCICR	0x0034
+/* ephy configuration register */
+#define CGU_EPHY	0x10
+/* power control register */
+#define PMU_PWDCR	0x1C
+/* power status register */
+#define PMU_PWDSR	0x20
+/* power control register */
+#define PMU_PWDCR1	0x24
+/* power status register */
+#define PMU_PWDSR1	0x28
+/* power control register */
+#define PWDCR(x) ((x) ? (PMU_PWDCR1) : (PMU_PWDCR))
+/* power status register */
+#define PWDSR(x) ((x) ? (PMU_PWDSR1) : (PMU_PWDSR))
+
+/* clock gates that we can en/disable */
+#define PMU_USB0_P	BIT(0)
+#define PMU_PCI		BIT(4)
+#define PMU_DMA		BIT(5)
+#define PMU_USB0	BIT(6)
+#define PMU_ASC0	BIT(7)
+#define PMU_EPHY	BIT(7)	/* ase */
+#define PMU_SPI		BIT(8)
+#define PMU_DFE		BIT(9)
+#define PMU_EBU		BIT(10)
+#define PMU_STP		BIT(11)
+#define PMU_GPT		BIT(12)
+#define PMU_AHBS	BIT(13) /* vr9 */
+#define PMU_FPI		BIT(14)
+#define PMU_AHBM	BIT(15)
+#define PMU_ASC1	BIT(17)
+#define PMU_PPE_QSB	BIT(18)
+#define PMU_PPE_SLL01	BIT(19)
+#define PMU_PPE_TC	BIT(21)
+#define PMU_PPE_EMA	BIT(22)
+#define PMU_PPE_DPLUM	BIT(23)
+#define PMU_PPE_DPLUS	BIT(24)
+#define PMU_USB1_P	BIT(26)
+#define PMU_USB1	BIT(27)
+#define PMU_SWITCH	BIT(28)
+#define PMU_PPE_TOP	BIT(29)
+#define PMU_GPHY	BIT(30)
+#define PMU_PCIE_CLK	BIT(31)
+
+#define PMU1_PCIE_PHY	BIT(0)
+#define PMU1_PCIE_CTL	BIT(1)
+#define PMU1_PCIE_PDI	BIT(4)
+#define PMU1_PCIE_MSI	BIT(5)
+
+#define pmu_w32(x, y)	ltq_w32((x), pmu_membase + (y))
+#define pmu_r32(x)	ltq_r32(pmu_membase + (x))
+
+static void __iomem *pmu_membase;
+void __iomem *ltq_cgu_membase;
+void __iomem *ltq_ebu_membase;
+
+/* legacy function kept alive to ease clkdev transition */
+void ltq_pmu_enable(unsigned int module)
+{
+	int err = 1000000;
+
+	pmu_w32(pmu_r32(PMU_PWDCR) & ~module, PMU_PWDCR);
+	do {} while (--err && (pmu_r32(PMU_PWDSR) & module));
+
+	if (!err)
+		panic("activating PMU module failed!");
+}
+EXPORT_SYMBOL(ltq_pmu_enable);
+
+/* legacy function kept alive to ease clkdev transition */
+void ltq_pmu_disable(unsigned int module)
+{
+	pmu_w32(pmu_r32(PMU_PWDCR) | module, PMU_PWDCR);
+}
+EXPORT_SYMBOL(ltq_pmu_disable);
+
+/* enable a hw clock */
+static int cgu_enable(struct clk *clk)
+{
+	ltq_cgu_w32(ltq_cgu_r32(CGU_IFCCR) | clk->bits, CGU_IFCCR);
+	return 0;
+}
+
+/* disable a hw clock */
+static void cgu_disable(struct clk *clk)
+{
+	ltq_cgu_w32(ltq_cgu_r32(CGU_IFCCR) & ~clk->bits, CGU_IFCCR);
+}
+
+/* enable a clock gate */
+static int pmu_enable(struct clk *clk)
+{
+	int retry = 1000000;
+
+	pmu_w32(pmu_r32(PWDCR(clk->module)) & ~clk->bits,
+		PWDCR(clk->module));
+	do {} while (--retry && (pmu_r32(PWDSR(clk->module)) & clk->bits));
+
+	if (!retry)
+		panic("activating PMU module failed!\n");
+
+	return 0;
+}
+
+/* disable a clock gate */
+static void pmu_disable(struct clk *clk)
+{
+	pmu_w32(pmu_r32(PWDCR(clk->module)) | clk->bits,
+		PWDCR(clk->module));
+}
+
+/* the pci enable helper */
+static int pci_enable(struct clk *clk)
+{
+	unsigned int ifccr = ltq_cgu_r32(CGU_IFCCR);
+	/* set bus clock speed */
+	if (of_machine_is_compatible("lantiq,ar9")) {
+		ifccr &= ~0x1f00000;
+		if (clk->rate == CLOCK_33M)
+			ifccr |= 0xe00000;
+		else
+			ifccr |= 0x700000; /* 62.5M */
+	} else {
+		ifccr &= ~0xf00000;
+		if (clk->rate == CLOCK_33M)
+			ifccr |= 0x800000;
+		else
+			ifccr |= 0x400000; /* 62.5M */
+	}
+	ltq_cgu_w32(ifccr, CGU_IFCCR);
+	pmu_enable(clk);
+	return 0;
+}
+
+/* enable the external clock as a source */
+static int pci_ext_enable(struct clk *clk)
+{
+	ltq_cgu_w32(ltq_cgu_r32(CGU_IFCCR) & ~(1 << 16),
+		CGU_IFCCR);
+	ltq_cgu_w32((1 << 30), CGU_PCICR);
+	return 0;
+}
+
+/* disable the external clock as a source */
+static void pci_ext_disable(struct clk *clk)
+{
+	ltq_cgu_w32(ltq_cgu_r32(CGU_IFCCR) | (1 << 16),
+		CGU_IFCCR);
+	ltq_cgu_w32((1 << 31) | (1 << 30), CGU_PCICR);
+}
+
+/* enable a clockout source */
+static int clkout_enable(struct clk *clk)
+{
+	int i;
+
+	/* get the correct rate */
+	for (i = 0; i < 4; i++) {
+		if (clk->rates[i] == clk->rate) {
+			int shift = 14 - (2 * clk->module);
+			unsigned int ifccr = ltq_cgu_r32(CGU_IFCCR);
+
+			ifccr &= ~(3 << shift);
+			ifccr |= i << shift;
+			ltq_cgu_w32(ifccr, CGU_IFCCR);
+			return 0;
+		}
+	}
+	return -1;
+}
+
+/* manage the clock gates via PMU */
+static void clkdev_add_pmu(const char *dev, const char *con,
+					unsigned int module, unsigned int bits)
+{
+	struct clk *clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
+
+	clk->cl.dev_id = dev;
+	clk->cl.con_id = con;
+	clk->cl.clk = clk;
+	clk->enable = pmu_enable;
+	clk->disable = pmu_disable;
+	clk->module = module;
+	clk->bits = bits;
+	clkdev_add(&clk->cl);
+}
+
+/* manage the clock generator */
+static void clkdev_add_cgu(const char *dev, const char *con,
+					unsigned int bits)
+{
+	struct clk *clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
+
+	clk->cl.dev_id = dev;
+	clk->cl.con_id = con;
+	clk->cl.clk = clk;
+	clk->enable = cgu_enable;
+	clk->disable = cgu_disable;
+	clk->bits = bits;
+	clkdev_add(&clk->cl);
+}
+
+/* pci needs its own enable function as the setup is a bit more complex */
+static unsigned long valid_pci_rates[] = {CLOCK_33M, CLOCK_62_5M, 0};
+
+static void clkdev_add_pci(void)
+{
+	struct clk *clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
+	struct clk *clk_ext = kzalloc(sizeof(struct clk), GFP_KERNEL);
+
+	/* main pci clock */
+	clk->cl.dev_id = "17000000.pci";
+	clk->cl.con_id = NULL;
+	clk->cl.clk = clk;
+	clk->rate = CLOCK_33M;
+	clk->rates = valid_pci_rates;
+	clk->enable = pci_enable;
+	clk->disable = pmu_disable;
+	clk->module = 0;
+	clk->bits = PMU_PCI;
+	clkdev_add(&clk->cl);
+
+	/* use internal/external bus clock */
+	clk_ext->cl.dev_id = "17000000.pci";
+	clk_ext->cl.con_id = "external";
+	clk_ext->cl.clk = clk_ext;
+	clk_ext->enable = pci_ext_enable;
+	clk_ext->disable = pci_ext_disable;
+	clkdev_add(&clk_ext->cl);
+}
+
+/* xway socs can generate clocks on gpio pins */
+static unsigned long valid_clkout_rates[4][5] = {
+	{CLOCK_32_768K, CLOCK_1_536M, CLOCK_2_5M, CLOCK_12M, 0},
+	{CLOCK_40M, CLOCK_12M, CLOCK_24M, CLOCK_48M, 0},
+	{CLOCK_25M, CLOCK_40M, CLOCK_30M, CLOCK_60M, 0},
+	{CLOCK_12M, CLOCK_50M, CLOCK_32_768K, CLOCK_25M, 0},
+};
+
+static void clkdev_add_clkout(void)
+{
+	int i;
+
+	for (i = 0; i < 4; i++) {
+		struct clk *clk;
+		char *name;
+
+		name = kzalloc(sizeof("clkout0"), GFP_KERNEL);
+		sprintf(name, "clkout%d", i);
+
+		clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
+		clk->cl.dev_id = "1f103000.cgu";
+		clk->cl.con_id = name;
+		clk->cl.clk = clk;
+		clk->rate = 0;
+		clk->rates = valid_clkout_rates[i];
+		clk->enable = clkout_enable;
+		clk->module = i;
+		clkdev_add(&clk->cl);
+	}
+}
+
+/* bring up all register ranges that we need for basic system control */
+void __init ltq_soc_init(void)
+{
+	struct resource res_pmu, res_cgu, res_ebu;
+	struct device_node *np_pmu =
+			of_find_compatible_node(NULL, NULL, "lantiq,pmu-xway");
+	struct device_node *np_cgu =
+			of_find_compatible_node(NULL, NULL, "lantiq,cgu-xway");
+	struct device_node *np_ebu =
+			of_find_compatible_node(NULL, NULL, "lantiq,ebu-xway");
+
+	/* check if all the core register ranges are available */
+	if (!np_pmu || !np_cgu || !np_ebu)
+		panic("Failed to load core nodess from devicetree");
+
+	if (of_address_to_resource(np_pmu, 0, &res_pmu) ||
+			of_address_to_resource(np_cgu, 0, &res_cgu) ||
+			of_address_to_resource(np_ebu, 0, &res_ebu))
+		panic("Failed to get core resources");
+
+	if ((request_mem_region(res_pmu.start, resource_size(&res_pmu),
+				res_pmu.name) < 0) ||
+		(request_mem_region(res_cgu.start, resource_size(&res_cgu),
+				res_cgu.name) < 0) ||
+		(request_mem_region(res_ebu.start, resource_size(&res_ebu),
+				res_ebu.name) < 0))
+		pr_err("Failed to request core reources");
+
+	pmu_membase = ioremap_nocache(res_pmu.start, resource_size(&res_pmu));
+	ltq_cgu_membase = ioremap_nocache(res_cgu.start,
+						resource_size(&res_cgu));
+	ltq_ebu_membase = ioremap_nocache(res_ebu.start,
+						resource_size(&res_ebu));
+	if (!pmu_membase || !ltq_cgu_membase || !ltq_ebu_membase)
+		panic("Failed to remap core resources");
+
+	/* make sure to unprotect the memory region where flash is located */
+	ltq_ebu_w32(ltq_ebu_r32(LTQ_EBU_BUSCON0) & ~EBU_WRDIS, LTQ_EBU_BUSCON0);
+
+	/* add our generic xway clocks */
+	clkdev_add_pmu("10000000.fpi", NULL, 0, PMU_FPI);
+	clkdev_add_pmu("1e100400.serial", NULL, 0, PMU_ASC0);
+	clkdev_add_pmu("1e100a00.gptu", NULL, 0, PMU_GPT);
+	clkdev_add_pmu("1e100bb0.stp", NULL, 0, PMU_STP);
+	clkdev_add_pmu("1e104100.dma", NULL, 0, PMU_DMA);
+	clkdev_add_pmu("1e100800.spi", NULL, 0, PMU_SPI);
+	clkdev_add_pmu("1e105300.ebu", NULL, 0, PMU_EBU);
+	clkdev_add_clkout();
+
+	/* add the soc dependent clocks */
+	if (!of_machine_is_compatible("lantiq,vr9"))
+		clkdev_add_pmu("1e180000.etop", NULL, 0, PMU_PPE);
+
+	if (!of_machine_is_compatible("lantiq,ase")) {
+		clkdev_add_pmu("1e100c00.serial", NULL, 0, PMU_ASC1);
+		clkdev_add_pci();
+	}
+
+	if (of_machine_is_compatible("lantiq,ase")) {
+		if (ltq_cgu_r32(CGU_SYS) & (1 << 5))
+			clkdev_add_static(CLOCK_266M, CLOCK_133M, CLOCK_133M);
+		else
+			clkdev_add_static(CLOCK_133M, CLOCK_133M, CLOCK_133M);
+		clkdev_add_cgu("1e180000.etop", "ephycgu", CGU_EPHY),
+		clkdev_add_pmu("1e180000.etop", "ephy", 0, PMU_EPHY);
+	} else if (of_machine_is_compatible("lantiq,vr9")) {
+		clkdev_add_static(ltq_vr9_cpu_hz(), ltq_vr9_fpi_hz(),
+				ltq_vr9_fpi_hz());
+		clkdev_add_pmu("1d900000.pcie", "phy", 1, PMU1_PCIE_PHY);
+		clkdev_add_pmu("1d900000.pcie", "bus", 0, PMU_PCIE_CLK);
+		clkdev_add_pmu("1d900000.pcie", "msi", 1, PMU1_PCIE_MSI);
+		clkdev_add_pmu("1d900000.pcie", "pdi", 1, PMU1_PCIE_PDI);
+		clkdev_add_pmu("1d900000.pcie", "ctl", 1, PMU1_PCIE_CTL);
+		clkdev_add_pmu("1d900000.pcie", "ahb", 0, PMU_AHBM | PMU_AHBS);
+	} else if (of_machine_is_compatible("lantiq,ar9")) {
+		clkdev_add_static(ltq_ar9_cpu_hz(), ltq_ar9_fpi_hz(),
+				ltq_ar9_fpi_hz());
+		clkdev_add_pmu("1e180000.etop", "switch", 0, PMU_SWITCH);
+	} else {
+		clkdev_add_static(ltq_danube_cpu_hz(), ltq_danube_fpi_hz(),
+				ltq_danube_fpi_hz());
+	}
+}

arch/mips/mm/c-octeon.c

@@ -21,6 +21,7 @@
 #include <asm/page.h>
 #include <asm/pgtable.h>
 #include <asm/r4kcache.h>
+#include <asm/traps.h>
 #include <asm/mmu_context.h>
 #include <asm/war.h>
 
@@ -248,6 +249,11 @@ static void __cpuinit probe_octeon(void)
 	}
 }
 
+static void  __cpuinit octeon_cache_error_setup(void)
+{
+	extern char except_vec2_octeon;
+	set_handler(0x100, &except_vec2_octeon, 0x80);
+}
 
 /**
  * Setup the Octeon cache flush routines
@@ -255,12 +261,6 @@ static void __cpuinit probe_octeon(void)
  */
 void __cpuinit octeon_cache_init(void)
 {
-	extern unsigned long ebase;
-	extern char except_vec2_octeon;
-
-	memcpy((void *)(ebase + 0x100), &except_vec2_octeon, 0x80);
-	octeon_flush_cache_sigtramp(ebase + 0x100);
-
 	probe_octeon();
 
 	shm_align_mask = PAGE_SIZE - 1;
@@ -280,6 +280,8 @@ void __cpuinit octeon_cache_init(void)
 
 	build_clear_page();
 	build_copy_page();
+
+	board_cache_error_setup = octeon_cache_error_setup;
 }
 
 /**

arch/mips/mm/c-r4k.c

@@ -32,7 +32,7 @@
 #include <asm/mmu_context.h>
 #include <asm/war.h>
 #include <asm/cacheflush.h> /* for run_uncached() */
-
+#include <asm/traps.h>
 
 /*
  * Special Variant of smp_call_function for use by cache functions:
@@ -1385,10 +1385,8 @@ static int __init setcoherentio(char *str)
 __setup("coherentio", setcoherentio);
 #endif
 
-void __cpuinit r4k_cache_init(void)
+static void __cpuinit r4k_cache_error_setup(void)
 {
-	extern void build_clear_page(void);
-	extern void build_copy_page(void);
 	extern char __weak except_vec2_generic;
 	extern char __weak except_vec2_sb1;
 	struct cpuinfo_mips *c = &current_cpu_data;
@@ -1403,6 +1401,13 @@ void __cpuinit r4k_cache_init(void)
 		set_uncached_handler(0x100, &except_vec2_generic, 0x80);
 		break;
 	}
+}
+
+void __cpuinit r4k_cache_init(void)
+{
+	extern void build_clear_page(void);
+	extern void build_copy_page(void);
+	struct cpuinfo_mips *c = &current_cpu_data;
 
 	probe_pcache();
 	setup_scache();
@@ -1465,4 +1470,5 @@ void __cpuinit r4k_cache_init(void)
 	local_r4k___flush_cache_all(NULL);
 #endif
 	coherency_setup();
+	board_cache_error_setup = r4k_cache_error_setup;
 }