Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC cleanups from Olof Johansson:
 "A large cleanup branch this release, with a healthy 10k negative line
  delta.

  Most of this is removal of legacy (non-DT) support of shmobile
  platforms.  There is also removal of two non-DT platforms on OMAP, and
  the plat-samsung directory is cleaned out by moving most of the
  previously shared-location-but-not-actually-shared files from there to
  the appropriate mach directories instead.

  There are other sets of changes in here as well:

   - Rob Herring removed use of set_irq_flags under all platforms and
     moved to genirq alternatives

   - a series of timer API conversions to set-state interface

   - ep93xx, nomadik and ux500 cleanups from Linus Walleij

   - __init annotation fixes from Nicolas Pitre

   + a bunch of other changes that all add up to a nice set of cleanups"

* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (108 commits)
  ARM/fb: ep93xx: switch framebuffer to use modedb only
  ARM: gemini: Setup timer3 as free running timer
  ARM: gemini: Use timer1 for clockevent
  ARM: gemini: Add missing register definitions for gemini timer
  ARM: ep93xx/timer: Migrate to new 'set-state' interface
  ARM: nomadik: push accelerometer down to boards
  ARM: nomadik: move l2x0 setup to device tree
  ARM: nomadik: selectively enable UART0 on boards
  ARM: nomadik: move hog code to use DT hogs
  ARM: shmobile: Fix mismerges
  ARM: ux500: simplify secondary CPU boot
  ARM: SAMSUNG: remove keypad-core header in plat-samsung
  ARM: SAMSUNG: local watchdog-reset header in mach-s3c64xx
  ARM: SAMSUNG: local onenand-core header in mach-s3c64xx
  ARM: SAMSUNG: local irq-uart header in mach-s3c64xx
  ARM: SAMSUNG: local backlight header in mach-s3c64xx
  ARM: SAMSUNG: local ata-core header in mach-s3c64xx
  ARM: SAMSUNG: local regs-usb-hsotg-phy header in mach-s3c64xx
  ARM: SAMSUNG: local spi-core header in mach-s3c24xx
  ARM: SAMSUNG: local nand-core header in mach-s3c24xx
  ...

Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt

@@ -8,10 +8,10 @@ Required properties:
 - interrupts : The interrupt from the HDA controller.
 - clocks : Must contain an entry for each required entry in clock-names.
   See ../clocks/clock-bindings.txt for details.
-- clock-names : Must include the following entries: hda, hdacodec_2x, hda2hdmi
+- clock-names : Must include the following entries: hda, hda2hdmi, hda2codec_2x
 - resets : Must contain an entry for each entry in reset-names.
   See ../reset/reset.txt for details.
-- reset-names : Must include the following entries: hda, hdacodec_2x, hda2hdmi
+- reset-names : Must include the following entries: hda, hda2hdmi, hda2codec_2x
 
 Example:
 
@@ -24,7 +24,7 @@ hda@0,70030000 {
 		 <&tegra_car TEGRA124_CLK_HDA2CODEC_2X>;
 	clock-names = "hda", "hda2hdmi", "hda2codec_2x";
 	resets = <&tegra_car 125>, /* hda */
-		 <&tegra_car 128>; /* hda2hdmi */
-		 <&tegra_car 111>, /* hda2codec_2x */
+		 <&tegra_car 128>, /* hda2hdmi */
+		 <&tegra_car 111>; /* hda2codec_2x */
 	reset-names = "hda", "hda2hdmi", "hda2codec_2x";
 };

MAINTAINERS

@@ -1471,9 +1471,7 @@ F:	arch/arm/boot/dts/emev2*
 F:	arch/arm/boot/dts/r7s*
 F:	arch/arm/boot/dts/r8a*
 F:	arch/arm/boot/dts/sh*
-F:	arch/arm/configs/armadillo800eva_defconfig
 F:	arch/arm/configs/bockw_defconfig
-F:	arch/arm/configs/kzm9g_defconfig
 F:	arch/arm/configs/marzen_defconfig
 F:	arch/arm/configs/shmobile_defconfig
 F:	arch/arm/include/debug/renesas-scif.S

arch/arm/Kconfig

@@ -268,7 +268,6 @@ config PHYS_OFFSET
 	depends on !ARM_PATCH_PHYS_VIRT
 	default DRAM_BASE if !MMU
 	default 0x00000000 if ARCH_EBSA110 || \
-			EP93XX_SDCE3_SYNC_PHYS_OFFSET || \
 			ARCH_FOOTBRIDGE || \
 			ARCH_INTEGRATOR || \
 			ARCH_IOP13XX || \
@@ -277,10 +276,7 @@ config PHYS_OFFSET
 	default 0x10000000 if ARCH_OMAP1 || ARCH_RPC
 	default 0x20000000 if ARCH_S5PV210
 	default 0x70000000 if REALVIEW_HIGH_PHYS_OFFSET
-	default 0xc0000000 if EP93XX_SDCE0_PHYS_OFFSET || ARCH_SA1100
-	default 0xd0000000 if EP93XX_SDCE1_PHYS_OFFSET
-	default 0xe0000000 if EP93XX_SDCE2_PHYS_OFFSET
-	default 0xf0000000 if EP93XX_SDCE3_ASYNC_PHYS_OFFSET
+	default 0xc0000000 if ARCH_SA1100
 	help
 	  Please provide the physical address corresponding to the
 	  location of main memory in your system.
@@ -418,11 +414,14 @@ config ARCH_EP93XX
 	bool "EP93xx-based"
 	select ARCH_HAS_HOLES_MEMORYMODEL
 	select ARCH_REQUIRE_GPIOLIB
-	select ARCH_USES_GETTIMEOFFSET
 	select ARM_AMBA
+	select ARM_PATCH_PHYS_VIRT
 	select ARM_VIC
+	select AUTO_ZRELADDR
 	select CLKDEV_LOOKUP
+	select CLKSRC_MMIO
 	select CPU_ARM920T
+	select GENERIC_CLOCKEVENTS
 	help
 	  This enables support for the Cirrus EP93xx series of CPUs.
 

arch/arm/boot/compressed/Makefile

@@ -51,10 +51,6 @@ else
 endif
 endif
 
-ifeq ($(CONFIG_ARCH_SHMOBILE_LEGACY),y)
-OBJS		+= head-shmobile.o
-endif
-
 #
 # We now have a PIC decompressor implementation.  Decompressors running
 # from RAM should not define ZTEXTADDR.  Decompressors running directly

arch/arm/boot/compressed/head-shmobile.S

@@ -1,71 +0,0 @@
-/*
- * The head-file for SH-Mobile ARM platforms
- *
- * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
- * Simon Horman <horms@verge.net.au>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; version 2 of the License.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
- */
-
-#ifdef CONFIG_ZBOOT_ROM
-
-	.section	".start", "ax"
-
-	/* load board-specific initialization code */
-#include <mach/zboot.h>
-
-	adr	r0, dtb_info
-	ldmia	r0, {r1, r3, r4, r5, r7}
-
-	sub	r0, r0, r1		@ calculate the delta offset
-	add	r5, r5, r0		@ _edata
-
-	ldr	lr, [r5, #0]		@ check if valid DTB is present
-	cmp	lr, r3
-	bne	0f
-
-	add	r9, r7, #31		@ rounded up to a multiple
-	bic	r9, r9, #31		@ ... of 32 bytes
-
-	add	r6, r9, r5		@ copy from _edata
-	add	r9, r9, r4		@ to MEMORY_START
-
-1:	ldmdb	r6!, {r0 - r3, r10 - r12, lr}
-	cmp	r6, r5
-	stmdb	r9!, {r0 - r3, r10 - r12, lr}
-	bhi	1b
-
-	/* Success: Zero board ID, pointer to start of memory for atag/dtb */
-	mov	r7, #0
-	mov	r8, r4
-	b	2f
-
-	.align	2
-dtb_info:
-	.word	dtb_info
-#ifndef __ARMEB__
-	.word	0xedfe0dd0		@ sig is 0xd00dfeed big endian
-#else
-	.word	0xd00dfeed
-#endif
-	.word	MEMORY_START
-	.word	_edata
-	.word	0x4000			@ maximum DTB size
-0:
-	/* Failure: Zero board ID, NULL atag/dtb */
-	mov 	r7, #0
-	mov	r8, #0			@ pass null pointer as atag
-2 :
-
-#endif /* CONFIG_ZBOOT_ROM */

arch/arm/boot/dts/Makefile

@@ -501,11 +501,8 @@ dtb-$(CONFIG_ARCH_S5PV210) += \
 	s5pv210-smdkv210.dtb \
 	s5pv210-torbreck.dtb
 dtb-$(CONFIG_ARCH_SHMOBILE_LEGACY) += \
-	r8a7740-armadillo800eva.dtb \
 	r8a7778-bockw.dtb \
-	r8a7778-bockw-reference.dtb \
-	r8a7779-marzen.dtb \
-	sh73a0-kzm9g.dtb
+	r8a7778-bockw-reference.dtb
 dtb-$(CONFIG_ARCH_SHMOBILE_MULTI) += \
 	emev2-kzm9d.dtb \
 	r7s72100-genmai.dtb \

arch/arm/boot/dts/ste-nomadik-nhk15.dts

@@ -17,12 +17,22 @@
 	};
 
 	aliases {
+		serial0 = &uart0;
 		serial1 = &uart1;
 		stmpe-i2c0 = &stmpe0;
 		stmpe-i2c1 = &stmpe1;
 	};
 
 	pinctrl {
+		uart0 {
+			uart0_nhk_mode: uart0_mux {
+				u0_default_mux {
+					function = "u0";
+					groups = "u0txrx_a_1", "u0ctsrts_a_1";
+				};
+			};
+		};
+
 		stmpe2401_1 {
 			stmpe2401_1_nhk_mode: stmpe2401_1_nhk {
 				nhk_cfg1 {
@@ -73,6 +83,11 @@
 	};
 
 	i2c0 {
+		lis3lv02dl@1d {
+			/* Accelerometer */
+			compatible = "st,lis3lv02dl-accel";
+			reg = <0x1d>;
+		};
 		stmpe0: stmpe2401@43 {
 			compatible = "st,stmpe2401";
 			reg = <0x43>;
@@ -131,22 +146,30 @@
 				#gpio-cells = <2>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
+				/*
+				 * This will turn off SATA so that MMC/SD
+				 * can thrive
+				 */
+				mmcsd-gpio {
+					gpio-hog;
+					gpios = <2 0x0>;
+					output-low;
+					line-name = "SATA EN";
+				};
 			};
 		};
 	};
 
 	amba {
+		/* Activate RX/TX and CTS/RTS on UART 0 */
+		uart0: uart@101fd000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_nhk_mode>;
+			status = "okay";
+		};
 		mmcsd: sdi@101f6000 {
 			cd-gpios = <&stmpe_gpio44 7 GPIO_ACTIVE_LOW>;
 			wp-gpios = <&stmpe_gpio44 18 GPIO_ACTIVE_HIGH>;
 		};
 	};
-
-	/* Custom board node with GPIO pins to active etc */
-	usb-s8815 {
-		/* This will turn off SATA so that MMC/SD can thrive */
-		mmcsd-gpio {
-			gpios = <&stmpe_gpio44 2 0x1>;
-		};
-	};
 };

arch/arm/boot/dts/ste-nomadik-s8815.dts

@@ -16,9 +16,20 @@
 	};
 
 	aliases {
+		serial0 = &uart0;
 		serial1 = &uart1;
 	};
 
+	gpio3: gpio@101e7000 {
+		/* This hog will bias the MMC/SD card detect line */
+		mmcsd-gpio {
+			gpio-hog;
+			gpios = <16 0x0>;
+			output-low;
+			line-name = "card detect bias";
+		};
+	};
+
 	src@101e0000 {
 		/* These chrystal drivers are not used on this board */
 		disable-sxtalo;
@@ -30,6 +41,15 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&cd_default_mode>;
 
+		uart0 {
+			/* Only use RX/TX pins */
+			uart0_s8815_mode: uart0_mux {
+				u0_default_mux {
+					function = "u0";
+					groups = "u0txrx_a_1";
+				};
+			};
+		};
 		mmcsd-cd {
 			cd_default_mode: cd_default {
 				cd_default_cfg1 {
@@ -85,6 +105,14 @@
 		};
 	};
 
+	i2c1 {
+		lis3lv02dl@1d {
+			/* Accelerometer */
+			compatible = "st,lis3lv02dl-accel";
+			reg = <0x1d>;
+		};
+	};
+
 	/* GPIO I2C connected to the USB portions of the STw4811 only */
 	gpio-i2c {
 		compatible = "i2c-gpio";
@@ -102,21 +130,19 @@
 	};
 
 
-	/* Configure card detect for the uSD slot */
 	amba {
+		/* Activate RXTX on UART 0 */
+		uart0: uart@101fd000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_s8815_mode>;
+			status = "okay";
+		};
+		/* Configure card detect for the uSD slot */
 		mmcsd: sdi@101f6000 {
 			cd-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
 		};
 	};
 
-	/* Custom board node with GPIO pins to active etc */
-	usb-s8815 {
-		/* This will bias the MMC/SD card detect line */
-		mmcsd-gpio {
-			gpios = <&gpio3 16 0x1>;
-		};
-	};
-
 	/* The user LED on the board is set up to be used for heartbeat */
 	leds {
 		compatible = "gpio-leds";

arch/arm/boot/dts/ste-nomadik-stn8815.dtsi

@@ -21,6 +21,13 @@
 		interrupts = <30>;
 		cache-unified;
 		cache-level = <2>;
+		cache-size = <131072>;
+		cache-sets = <512>;
+		cache-line-size = <32>;
+		/* At full speed latency must be >=2 */
+		arm,tag-latency = <2>;
+		arm,data-latency = <2 2>;
+		arm,dirty-latency = <2>;
 	};
 
 	mtu0: mtu@101e2000 {
@@ -97,14 +104,6 @@
 	pinctrl {
 		compatible = "stericsson,stn8815-pinctrl";
 		/* Pin configurations */
-		uart0 {
-			uart0_default_mux: uart0_mux {
-				u0_default_mux {
-					function = "u0";
-					groups = "u0_a_1";
-				};
-			};
-		};
 		uart1 {
 			uart1_default_mux: uart1_mux {
 				u1_default_mux {
@@ -721,11 +720,6 @@
 			   compatible = "st,stw5095";
 			   reg = <0x1a>;
 		};
-		lis3lv02dl@1d {
-			/* Accelerometer */
-			compatible = "st,lis3lv02dl-accel";
-			reg = <0x1d>;
-		};
 	};
 
 	amba {
@@ -755,8 +749,6 @@
 			interrupts = <12>;
 			clocks = <&uart0clk>, <&pclkuart0>;
 			clock-names = "uartclk", "apb_pclk";
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart0_default_mux>;
 			status = "disabled";
 		};
 

arch/arm/common/it8152.c

@@ -91,7 +91,7 @@ void it8152_init_irq(void)
 	for (irq = IT8152_IRQ(0); irq <= IT8152_LAST_IRQ; irq++) {
 		irq_set_chip_and_handler(irq, &it8152_irq_chip,
 					 handle_level_irq);
-		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+		irq_clear_status_flags(irq, IRQ_NOREQUEST | IRQ_NOPROBE);
 	}
 }
 

arch/arm/common/locomo.c

@@ -138,9 +138,9 @@ static struct locomo_dev_info locomo_devices[] = {
 	},
 };
 
-static void locomo_handler(unsigned int irq, struct irq_desc *desc)
+static void locomo_handler(unsigned int __irq, struct irq_desc *desc)
 {
-	struct locomo *lchip = irq_get_chip_data(irq);
+	struct locomo *lchip = irq_desc_get_chip_data(desc);
 	int req, i;
 
 	/* Acknowledge the parent IRQ */
@@ -150,6 +150,8 @@ static void locomo_handler(unsigned int irq, struct irq_desc *desc)
 	req = locomo_readl(lchip->base + LOCOMO_ICR) & 0x0f00;
 
 	if (req) {
+		unsigned int irq;
+
 		/* generate the next interrupt(s) */
 		irq = lchip->irq_base;
 		for (i = 0; i <= 3; i++, irq++) {
@@ -205,7 +207,7 @@ static void locomo_setup_irq(struct locomo *lchip)
 	for ( ; irq <= lchip->irq_base + 3; irq++) {
 		irq_set_chip_and_handler(irq, &locomo_chip, handle_level_irq);
 		irq_set_chip_data(irq, lchip);
-		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+		irq_clear_status_flags(irq, IRQ_NOREQUEST | IRQ_NOPROBE);
 	}
 }
 
@@ -475,8 +477,7 @@ static void __locomo_remove(struct locomo *lchip)
 	device_for_each_child(lchip->dev, NULL, locomo_remove_child);
 
 	if (lchip->irq != NO_IRQ) {
-		irq_set_chained_handler(lchip->irq, NULL);
-		irq_set_handler_data(lchip->irq, NULL);
+		irq_set_chained_handler_and_data(lchip->irq, NULL, NULL);
 	}
 
 	iounmap(lchip->base);

arch/arm/common/sa1111.c

@@ -197,10 +197,11 @@ static struct sa1111_dev_info sa1111_devices[] = {
  * will call us again if there are more interrupts to process.
  */
 static void
-sa1111_irq_handler(unsigned int irq, struct irq_desc *desc)
+sa1111_irq_handler(unsigned int __irq, struct irq_desc *desc)
 {
+	unsigned int irq = irq_desc_get_irq(desc);
 	unsigned int stat0, stat1, i;
-	struct sa1111 *sachip = irq_get_handler_data(irq);
+	struct sa1111 *sachip = irq_desc_get_handler_data(desc);
 	void __iomem *mapbase = sachip->base + SA1111_INTC;
 
 	stat0 = sa1111_readl(mapbase + SA1111_INTSTATCLR0);
@@ -486,7 +487,7 @@ static int sa1111_setup_irq(struct sa1111 *sachip, unsigned irq_base)
 		irq_set_chip_and_handler(irq, &sa1111_low_chip,
 					 handle_edge_irq);
 		irq_set_chip_data(irq, sachip);
-		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+		irq_clear_status_flags(irq, IRQ_NOREQUEST | IRQ_NOPROBE);
 	}
 
 	for (i = AUDXMTDMADONEA; i <= IRQ_S1_BVD1_STSCHG; i++) {
@@ -494,7 +495,7 @@ static int sa1111_setup_irq(struct sa1111 *sachip, unsigned irq_base)
 		irq_set_chip_and_handler(irq, &sa1111_high_chip,
 					 handle_edge_irq);
 		irq_set_chip_data(irq, sachip);
-		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+		irq_clear_status_flags(irq, IRQ_NOREQUEST | IRQ_NOPROBE);
 	}
 
 	/*

arch/arm/configs/armadillo800eva_defconfig

@@ -1,162 +0,0 @@
-CONFIG_EXPERIMENTAL=y
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=16
-# CONFIG_UTS_NS is not set
-# CONFIG_IPC_NS is not set
-# CONFIG_PID_NS is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_PERF_EVENTS=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_SHMOBILE_LEGACY=y
-CONFIG_ARCH_R8A7740=y
-CONFIG_MACH_ARMADILLO800EVA=y
-# CONFIG_SH_TIMER_TMU is not set
-CONFIG_ARM_THUMB=y
-CONFIG_CACHE_L2X0=y
-CONFIG_ARM_ERRATA_430973=y
-CONFIG_ARM_ERRATA_458693=y
-CONFIG_ARM_ERRATA_460075=y
-CONFIG_PL310_ERRATA_588369=y
-CONFIG_ARM_ERRATA_720789=y
-CONFIG_PL310_ERRATA_727915=y
-CONFIG_ARM_ERRATA_743622=y
-CONFIG_ARM_ERRATA_751472=y
-CONFIG_PL310_ERRATA_753970=y
-CONFIG_ARM_ERRATA_754322=y
-CONFIG_PL310_ERRATA_769419=y
-CONFIG_ARM_ERRATA_775420=y
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-CONFIG_FORCE_MAX_ZONEORDER=13
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_KEXEC=y
-CONFIG_VFP=y
-CONFIG_NEON=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-CONFIG_PM=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_MD=y
-CONFIG_BLK_DEV_DM=y
-CONFIG_NETDEVICES=y
-# CONFIG_NET_VENDOR_BROADCOM is not set
-# CONFIG_NET_VENDOR_CHELSIO is not set
-# CONFIG_NET_VENDOR_CIRRUS is not set
-# CONFIG_NET_VENDOR_FARADAY is not set
-# CONFIG_NET_VENDOR_INTEL is not set
-# CONFIG_NET_VENDOR_MARVELL is not set
-# CONFIG_NET_VENDOR_MICREL is not set
-# CONFIG_NET_VENDOR_NATSEMI is not set
-CONFIG_SH_ETH=y
-# CONFIG_NET_VENDOR_SEEQ is not set
-# CONFIG_NET_VENDOR_SMSC is not set
-# CONFIG_NET_VENDOR_STMICRO is not set
-# CONFIG_WLAN is not set
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_KEYBOARD_GPIO=y
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_ST1232=y
-# CONFIG_SERIO is not set
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_SH_SCI=y
-CONFIG_SERIAL_SH_SCI_NR_UARTS=9
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-CONFIG_I2C_GPIO=y
-CONFIG_I2C_SH_MOBILE=y
-# CONFIG_HWMON is not set
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_GPIO=y
-CONFIG_MEDIA_SUPPORT=y
-CONFIG_VIDEO_DEV=y
-CONFIG_MEDIA_CAMERA_SUPPORT=y
-CONFIG_V4L_PLATFORM_DRIVERS=y
-CONFIG_SOC_CAMERA=y
-CONFIG_SOC_CAMERA_MT9T112=y
-CONFIG_VIDEO_SH_MOBILE_CEU=y
-CONFIG_FB=y
-CONFIG_FB_SH_MOBILE_LCDC=y
-CONFIG_FB_SH_MOBILE_HDMI=y
-CONFIG_LCD_CLASS_DEVICE=y
-CONFIG_BACKLIGHT_PWM=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
-CONFIG_LOGO=y
-# CONFIG_LOGO_LINUX_MONO is not set
-# CONFIG_LOGO_LINUX_VGA16 is not set
-# CONFIG_SND_SUPPORT_OLD_API is not set
-# CONFIG_SND_VERBOSE_PROCFS is not set
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_ARM is not set
-CONFIG_SND_SOC_SH4_FSI=y
-# CONFIG_HID_SUPPORT is not set
-CONFIG_USB=y
-CONFIG_USB_RENESAS_USBHS=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_RENESAS_USBHS_UDC=y
-CONFIG_USB_ETH=m
-CONFIG_MMC=y
-CONFIG_MMC_SDHI=y
-CONFIG_MMC_SH_MMCIF=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_S35390A=y
-CONFIG_DMADEVICES=y
-CONFIG_SH_DMAE=y
-CONFIG_UIO=y
-CONFIG_UIO_PDRV_GENIRQ=y
-CONFIG_PWM=y
-CONFIG_PWM_RENESAS_TPU=y
-# CONFIG_DNOTIFY is not set
-CONFIG_MSDOS_FS=y
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-# CONFIG_MISC_FILESYSTEMS is not set
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_V4_1=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_ISO8859_1=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_ENABLE_MUST_CHECK is not set
-# CONFIG_ARM_UNWIND is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_MD5=y
-CONFIG_CRYPTO_DES=y
-CONFIG_CRYPTO_ANSI_CPRNG=y
-CONFIG_XZ_DEC=y

arch/arm/configs/kzm9g_defconfig

@@ -1,154 +0,0 @@
-# CONFIG_ARM_PATCH_PHYS_VIRT is not set
-CONFIG_EXPERIMENTAL=y
-# CONFIG_LOCALVERSION_AUTO is not set
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=16
-CONFIG_NAMESPACES=y
-# CONFIG_UTS_NS is not set
-# CONFIG_IPC_NS is not set
-# CONFIG_USER_NS is not set
-# CONFIG_PID_NS is not set
-# CONFIG_NET_NS is not set
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-CONFIG_SYSCTL_SYSCALL=y
-CONFIG_EMBEDDED=y
-CONFIG_PERF_EVENTS=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_FORCE_LOAD=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_SHMOBILE_LEGACY=y
-CONFIG_ARCH_SH73A0=y
-CONFIG_MACH_KZM9G=y
-CONFIG_MEMORY_START=0x41000000
-CONFIG_MEMORY_SIZE=0x1f000000
-CONFIG_ARM_ERRATA_743622=y
-CONFIG_ARM_ERRATA_754322=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_SMP=y
-CONFIG_SCHED_MC=y
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-CONFIG_HIGHMEM=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_KEXEC=y
-CONFIG_VFP=y
-CONFIG_NEON=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-CONFIG_PM=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_INET_DIAG is not set
-# CONFIG_IPV6 is not set
-CONFIG_IRDA=y
-CONFIG_SH_IRDA=y
-# CONFIG_WIRELESS is not set
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_SCSI=y
-CONFIG_BLK_DEV_SD=y
-CONFIG_NETDEVICES=y
-CONFIG_SMSC911X=y
-# CONFIG_WLAN is not set
-CONFIG_INPUT_SPARSEKMAP=y
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_KEYBOARD_GPIO=y
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_ST1232=y
-CONFIG_INPUT_MISC=y
-CONFIG_INPUT_ADXL34X=y
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_SH_SCI=y
-CONFIG_SERIAL_SH_SCI_NR_UARTS=9
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_SH_MOBILE=y
-CONFIG_GPIO_PCF857X=y
-# CONFIG_HWMON is not set
-CONFIG_MFD_AS3711=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_AS3711=y
-CONFIG_FB=y
-CONFIG_FB_SH_MOBILE_LCDC=y
-CONFIG_BACKLIGHT_AS3711=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_LOGO=y
-CONFIG_FB_SH_MOBILE_MERAM=y
-CONFIG_SOUND=y
-CONFIG_SND=y
-# CONFIG_SND_SUPPORT_OLD_API is not set
-# CONFIG_SND_VERBOSE_PROCFS is not set
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_ARM is not set
-# CONFIG_SND_USB is not set
-CONFIG_SND_SOC=y
-CONFIG_SND_SOC_SH4_FSI=y
-# CONFIG_HID_SUPPORT is not set
-CONFIG_USB=y
-CONFIG_USB_R8A66597_HCD=y
-CONFIG_USB_RENESAS_USBHS=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_RENESAS_USBHS_UDC=y
-CONFIG_USB_ETH=m
-CONFIG_USB_MASS_STORAGE=m
-CONFIG_MMC=y
-# CONFIG_MMC_BLOCK_BOUNCE is not set
-CONFIG_MMC_SDHI=y
-CONFIG_MMC_SH_MMCIF=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_RS5C372=y
-CONFIG_DMADEVICES=y
-CONFIG_SH_DMAE=y
-CONFIG_ASYNC_TX_DMA=y
-CONFIG_STAGING=y
-CONFIG_IIO=y
-CONFIG_AK8975=y
-# CONFIG_DNOTIFY is not set
-CONFIG_VFAT_FS=y
-CONFIG_TMPFS=y
-# CONFIG_MISC_FILESYSTEMS is not set
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFS_V4=y
-CONFIG_NFS_V4_1=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_CODEPAGE_437=y
-CONFIG_NLS_ISO8859_1=y
-# CONFIG_ENABLE_WARN_DEPRECATED is not set
-# CONFIG_ENABLE_MUST_CHECK is not set
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_DEBUG_PREEMPT is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
-# CONFIG_FTRACE is not set
-# CONFIG_ARM_UNWIND is not set
-CONFIG_CRYPTO=y
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_MD5=y
-CONFIG_CRYPTO_DES=y
-CONFIG_CRC16=y

arch/arm/kernel/irq.c

@@ -140,7 +140,7 @@ int __init arch_probe_nr_irqs(void)
 static bool migrate_one_irq(struct irq_desc *desc)
 {
 	struct irq_data *d = irq_desc_get_irq_data(desc);
-	const struct cpumask *affinity = d->affinity;
+	const struct cpumask *affinity = irq_data_get_affinity_mask(d);
 	struct irq_chip *c;
 	bool ret = false;
 
@@ -160,7 +160,7 @@ static bool migrate_one_irq(struct irq_desc *desc)
 	if (!c->irq_set_affinity)
 		pr_debug("IRQ%u: unable to set affinity\n", d->irq);
 	else if (c->irq_set_affinity(d, affinity, false) == IRQ_SET_MASK_OK && ret)
-		cpumask_copy(d->affinity, affinity);
+		cpumask_copy(irq_data_get_affinity_mask(d), affinity);
 
 	return ret;
 }

arch/arm/kernel/psci.c

@@ -278,7 +278,7 @@ out_put_node:
 	return err;
 }
 
-static const struct of_device_id psci_of_match[] __initconst = {
+static const struct of_device_id const psci_of_match[] __initconst = {
 	{ .compatible = "arm,psci", .data = psci_0_1_init},
 	{ .compatible = "arm,psci-0.2", .data = psci_0_2_init},
 	{},

arch/arm/kernel/smp_twd.c

@@ -36,29 +36,30 @@ static DEFINE_PER_CPU(bool, percpu_setup_called);
 static struct clock_event_device __percpu *twd_evt;
 static int twd_ppi;
 
-static void twd_set_mode(enum clock_event_mode mode,
-			struct clock_event_device *clk)
+static int twd_shutdown(struct clock_event_device *clk)
 {
-	unsigned long ctrl;
-
-	switch (mode) {
-	case CLOCK_EVT_MODE_PERIODIC:
-		ctrl = TWD_TIMER_CONTROL_ENABLE | TWD_TIMER_CONTROL_IT_ENABLE
-			| TWD_TIMER_CONTROL_PERIODIC;
-		writel_relaxed(DIV_ROUND_CLOSEST(twd_timer_rate, HZ),
-			twd_base + TWD_TIMER_LOAD);
-		break;
-	case CLOCK_EVT_MODE_ONESHOT:
-		/* period set, and timer enabled in 'next_event' hook */
-		ctrl = TWD_TIMER_CONTROL_IT_ENABLE | TWD_TIMER_CONTROL_ONESHOT;
-		break;
-	case CLOCK_EVT_MODE_UNUSED:
-	case CLOCK_EVT_MODE_SHUTDOWN:
-	default:
-		ctrl = 0;
-	}
+	writel_relaxed(0, twd_base + TWD_TIMER_CONTROL);
+	return 0;
+}
 
+static int twd_set_oneshot(struct clock_event_device *clk)
+{
+	/* period set, and timer enabled in 'next_event' hook */
+	writel_relaxed(TWD_TIMER_CONTROL_IT_ENABLE | TWD_TIMER_CONTROL_ONESHOT,
+		       twd_base + TWD_TIMER_CONTROL);
+	return 0;
+}
+
+static int twd_set_periodic(struct clock_event_device *clk)
+{
+	unsigned long ctrl = TWD_TIMER_CONTROL_ENABLE |
+			     TWD_TIMER_CONTROL_IT_ENABLE |
+			     TWD_TIMER_CONTROL_PERIODIC;
+
+	writel_relaxed(DIV_ROUND_CLOSEST(twd_timer_rate, HZ),
+		       twd_base + TWD_TIMER_LOAD);
 	writel_relaxed(ctrl, twd_base + TWD_TIMER_CONTROL);
+	return 0;
 }
 
 static int twd_set_next_event(unsigned long evt,
@@ -94,7 +95,7 @@ static void twd_timer_stop(void)
 {
 	struct clock_event_device *clk = raw_cpu_ptr(twd_evt);
 
-	twd_set_mode(CLOCK_EVT_MODE_UNUSED, clk);
+	twd_shutdown(clk);
 	disable_percpu_irq(clk->irq);
 }
 
@@ -296,7 +297,10 @@ static void twd_timer_setup(void)
 	clk->features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT |
 			CLOCK_EVT_FEAT_C3STOP;
 	clk->rating = 350;
-	clk->set_mode = twd_set_mode;
+	clk->set_state_shutdown = twd_shutdown;
+	clk->set_state_periodic = twd_set_periodic;
+	clk->set_state_oneshot = twd_set_oneshot;
+	clk->tick_resume = twd_shutdown;
 	clk->set_next_event = twd_set_next_event;
 	clk->irq = twd_ppi;
 	clk->cpumask = cpumask_of(cpu);

arch/arm/mach-at91/at91rm9200.c

@@ -37,7 +37,7 @@ static void __init at91rm9200_dt_device_init(void)
 	at91rm9200_pm_init();
 }
 
-static const char *at91rm9200_dt_board_compat[] __initconst = {
+static const char *const at91rm9200_dt_board_compat[] __initconst = {
 	"atmel,at91rm9200",
 	NULL
 };

arch/arm/mach-at91/at91sam9.c

@@ -72,7 +72,7 @@ static void __init at91sam9_dt_device_init(void)
 	at91sam9260_pm_init();
 }
 
-static const char *at91_dt_board_compat[] __initconst = {
+static const char *const at91_dt_board_compat[] __initconst = {
 	"atmel,at91sam9",
 	NULL
 };
@@ -89,7 +89,7 @@ static void __init at91sam9g45_dt_device_init(void)
 	at91sam9g45_pm_init();
 }
 
-static const char *at91sam9g45_board_compat[] __initconst = {
+static const char *const at91sam9g45_board_compat[] __initconst = {
 	"atmel,at91sam9g45",
 	NULL
 };
@@ -106,7 +106,7 @@ static void __init at91sam9x5_dt_device_init(void)
 	at91sam9x5_pm_init();
 }
 
-static const char *at91sam9x5_board_compat[] __initconst = {
+static const char *const at91sam9x5_board_compat[] __initconst = {
 	"atmel,at91sam9x5",
 	"atmel,at91sam9n12",
 	NULL

arch/arm/mach-at91/pm.c

@@ -311,7 +311,7 @@ static void at91sam9_sdram_standby(void)
 		at91_ramc_write(1, AT91_SDRAMC_LPR, saved_lpr1);
 }
 
-static const struct of_device_id ramc_ids[] __initconst = {
+static const struct of_device_id const ramc_ids[] __initconst = {
 	{ .compatible = "atmel,at91rm9200-sdramc", .data = at91rm9200_standby },
 	{ .compatible = "atmel,at91sam9260-sdramc", .data = at91sam9_sdram_standby },
 	{ .compatible = "atmel,at91sam9g45-ddramc", .data = at91_ddr_standby },

arch/arm/mach-at91/sama5.c

@@ -52,7 +52,7 @@ static void __init sama5_dt_device_init(void)
 	at91sam9x5_pm_init();
 }
 
-static const char *sama5_dt_board_compat[] __initconst = {
+static const char *const sama5_dt_board_compat[] __initconst = {
 	"atmel,sama5",
 	NULL
 };
@@ -63,7 +63,7 @@ DT_MACHINE_START(sama5_dt, "Atmel SAMA5")
 	.dt_compat	= sama5_dt_board_compat,
 MACHINE_END
 
-static const char *sama5_alt_dt_board_compat[] __initconst = {
+static const char *const sama5_alt_dt_board_compat[] __initconst = {
 	"atmel,sama5d4",
 	NULL
 };

arch/arm/mach-bcm/Makefile

@@ -39,10 +39,8 @@ obj-$(CONFIG_ARCH_BCM_5301X)	+= bcm_5301x.o
 
 # BCM63XXx
 ifeq ($(CONFIG_ARCH_BCM_63XX),y)
-CFLAGS_bcm63xx_headsmp.o	+= -march=armv7-a
 obj-y				+= bcm63xx.o
-obj-$(CONFIG_SMP)		+= bcm63xx_smp.o bcm63xx_headsmp.o \
-				   bcm63xx_pmb.o
+obj-$(CONFIG_SMP)		+= bcm63xx_smp.o bcm63xx_pmb.o
 endif
 
 ifeq ($(CONFIG_ARCH_BRCMSTB),y)

arch/arm/mach-bcm/bcm63xx_headsmp.S

@@ -1,23 +0,0 @@
-/*
- *  Copyright (C) 2015, Broadcom Corporation
- *  All Rights Reserved
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/linkage.h>
-#include <linux/init.h>
-#include <asm/assembler.h>
-
-ENTRY(bcm63138_secondary_startup)
- ARM_BE8(setend	be)
-	/*
-	 * L1 cache does have unpredictable contents at power-up clean its
-	 * contents without flushing
-	 */
-	bl      v7_invalidate_l1
-	nop
-
-	b	secondary_startup
-ENDPROC(bcm63138_secondary_startup)

arch/arm/mach-bcm/bcm63xx_smp.c

@@ -127,7 +127,7 @@ static int bcm63138_smp_boot_secondary(unsigned int cpu,
 	}
 
 	/* Locate the secondary CPU node */
-	dn = of_get_cpu_node(cpu_logical_map(cpu), NULL);
+	dn = of_get_cpu_node(cpu, NULL);
 	if (!dn) {
 		pr_err("SMP: failed to locate secondary CPU%d node\n", cpu);
 		ret = -ENODEV;
@@ -135,7 +135,7 @@ static int bcm63138_smp_boot_secondary(unsigned int cpu,
 	}
 
 	/* Write the secondary init routine to the BootLUT reset vector */
-	val = virt_to_phys(bcm63138_secondary_startup);
+	val = virt_to_phys(secondary_startup);
 	writel_relaxed(val, bootlut_base + BOOTLUT_RESET_VECT);
 
 	/* Power up the core, will jump straight to its reset vector when we

arch/arm/mach-bcm/bcm63xx_smp.h

@@ -3,7 +3,6 @@
 
 struct device_node;
 
-extern void bcm63138_secondary_startup(void);
 extern int bcm63xx_pmb_power_on_cpu(struct device_node *dn);
 
 #endif /* __BCM63XX_SMP_H */

arch/arm/mach-bcm/bcm_5301x.c

@@ -44,7 +44,7 @@ static void __init bcm5301x_init_early(void)
 			"imprecise external abort");
 }
 
-static const char __initconst *bcm5301x_dt_compat[] = {
+static const char *const bcm5301x_dt_compat[] __initconst = {
 	"brcm,bcm4708",
 	NULL,
 };

arch/arm/mach-bcm/bcm_kona_smc.c

@@ -33,7 +33,7 @@ struct bcm_kona_smc_data {
 	unsigned result;
 };
 
-static const struct of_device_id bcm_kona_smc_ids[] __initconst = {
+static const struct of_device_id const bcm_kona_smc_ids[] __initconst = {
 	{.compatible = "brcm,kona-smc"},
 	{.compatible = "bcm,kona-smc"}, /* deprecated name */
 	{},

arch/arm/mach-clps711x/board-autcpu12.c

@@ -160,7 +160,7 @@ static struct platform_device autcpu12_mmgpio_pdev __initdata = {
 	},
 };
 
-static const struct gpio autcpu12_gpios[] __initconst = {
+static const struct gpio const autcpu12_gpios[] __initconst = {
 	{ AUTCPU12_DPOT_CS,	GPIOF_OUT_INIT_HIGH,	"DPOT CS" },
 	{ AUTCPU12_DPOT_CLK,	GPIOF_OUT_INIT_LOW,	"DPOT CLK" },
 	{ AUTCPU12_DPOT_UD,	GPIOF_OUT_INIT_LOW,	"DPOT UD" },

arch/arm/mach-cns3xxx/core.c

@@ -113,30 +113,33 @@ void cns3xxx_power_off(void)
  */
 static void __iomem *cns3xxx_tmr1;
 
-static void cns3xxx_timer_set_mode(enum clock_event_mode mode,
-				   struct clock_event_device *clk)
+static int cns3xxx_shutdown(struct clock_event_device *clk)
+{
+	writel(0, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+	return 0;
+}
+
+static int cns3xxx_set_oneshot(struct clock_event_device *clk)
+{
+	unsigned long ctrl = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+
+	/* period set, and timer enabled in 'next_event' hook */
+	ctrl |= (1 << 2) | (1 << 9);
+	writel(ctrl, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+	return 0;
+}
+
+static int cns3xxx_set_periodic(struct clock_event_device *clk)
 {
 	unsigned long ctrl = readl(cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
 	int pclk = cns3xxx_cpu_clock() / 8;
 	int reload;
 
-	switch (mode) {
-	case CLOCK_EVT_MODE_PERIODIC:
-		reload = pclk * 20 / (3 * HZ) * 0x25000;
-		writel(reload, cns3xxx_tmr1 + TIMER1_AUTO_RELOAD_OFFSET);
-		ctrl |= (1 << 0) | (1 << 2) | (1 << 9);
-		break;
-	case CLOCK_EVT_MODE_ONESHOT:
-		/* period set, and timer enabled in 'next_event' hook */
-		ctrl |= (1 << 2) | (1 << 9);
-		break;
-	case CLOCK_EVT_MODE_UNUSED:
-	case CLOCK_EVT_MODE_SHUTDOWN:
-	default:
-		ctrl = 0;
-	}
-
+	reload = pclk * 20 / (3 * HZ) * 0x25000;
+	writel(reload, cns3xxx_tmr1 + TIMER1_AUTO_RELOAD_OFFSET);
+	ctrl |= (1 << 0) | (1 << 2) | (1 << 9);
 	writel(ctrl, cns3xxx_tmr1 + TIMER1_2_CONTROL_OFFSET);
+	return 0;
 }
 
 static int cns3xxx_timer_set_next_event(unsigned long evt,
@@ -151,12 +154,16 @@ static int cns3xxx_timer_set_next_event(unsigned long evt,
 }
 
 static struct clock_event_device cns3xxx_tmr1_clockevent = {
-	.name		= "cns3xxx timer1",
-	.features       = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
-	.set_mode	= cns3xxx_timer_set_mode,
-	.set_next_event	= cns3xxx_timer_set_next_event,
-	.rating		= 350,
-	.cpumask	= cpu_all_mask,
+	.name			= "cns3xxx timer1",
+	.features		= CLOCK_EVT_FEAT_PERIODIC |
+				  CLOCK_EVT_FEAT_ONESHOT,
+	.set_state_shutdown	= cns3xxx_shutdown,
+	.set_state_periodic	= cns3xxx_set_periodic,
+	.set_state_oneshot	= cns3xxx_set_oneshot,
+	.tick_resume		= cns3xxx_shutdown,
+	.set_next_event		= cns3xxx_timer_set_next_event,
+	.rating			= 350,
+	.cpumask		= cpu_all_mask,
 };
 
 static void __init cns3xxx_clockevents_init(unsigned int timer_irq)
@@ -339,7 +346,7 @@ static struct usb_ohci_pdata cns3xxx_usb_ohci_pdata = {
 	.power_off	= csn3xxx_usb_power_off,
 };
 
-static struct of_dev_auxdata cns3xxx_auxdata[] __initconst = {
+static const struct of_dev_auxdata const cns3xxx_auxdata[] __initconst = {
 	{ "intel,usb-ehci", CNS3XXX_USB_BASE, "ehci-platform", &cns3xxx_usb_ehci_pdata },
 	{ "intel,usb-ohci", CNS3XXX_USB_OHCI_BASE, "ohci-platform", &cns3xxx_usb_ohci_pdata },
 	{ "cavium,cns3420-ahci", CNS3XXX_SATA2_BASE, "ahci", NULL },
@@ -392,7 +399,7 @@ static void __init cns3xxx_init(void)
                         cns3xxx_auxdata, NULL);
 }
 
-static const char *cns3xxx_dt_compat[] __initdata = {
+static const char *const cns3xxx_dt_compat[] __initconst = {
 	"cavium,cns3410",
 	"cavium,cns3420",
 	NULL,

arch/arm/mach-davinci/cp_intc.c

@@ -112,7 +112,7 @@ static int cp_intc_host_map(struct irq_domain *h, unsigned int virq,
 	pr_debug("cp_intc_host_map(%d, 0x%lx)\n", virq, hw);
 
 	irq_set_chip(virq, &cp_intc_irq_chip);
-	set_irq_flags(virq, IRQF_VALID | IRQF_PROBE);
+	irq_set_probe(virq);
 	irq_set_handler(virq, handle_edge_irq);
 	return 0;
 }

arch/arm/mach-davinci/da850.c

@@ -715,7 +715,7 @@ const short da850_lcdcntl_pins[] __initconst = {
 	-1
 };
 
-const short da850_vpif_capture_pins[] __initdata = {
+const short da850_vpif_capture_pins[] __initconst = {
 	DA850_VPIF_DIN0, DA850_VPIF_DIN1, DA850_VPIF_DIN2, DA850_VPIF_DIN3,
 	DA850_VPIF_DIN4, DA850_VPIF_DIN5, DA850_VPIF_DIN6, DA850_VPIF_DIN7,
 	DA850_VPIF_DIN8, DA850_VPIF_DIN9, DA850_VPIF_DIN10, DA850_VPIF_DIN11,
@@ -725,7 +725,7 @@ const short da850_vpif_capture_pins[] __initdata = {
 	-1
 };
 
-const short da850_vpif_display_pins[] __initdata = {
+const short da850_vpif_display_pins[] __initconst = {
 	DA850_VPIF_DOUT0, DA850_VPIF_DOUT1, DA850_VPIF_DOUT2, DA850_VPIF_DOUT3,
 	DA850_VPIF_DOUT4, DA850_VPIF_DOUT5, DA850_VPIF_DOUT6, DA850_VPIF_DOUT7,
 	DA850_VPIF_DOUT8, DA850_VPIF_DOUT9, DA850_VPIF_DOUT10,

arch/arm/mach-davinci/da8xx-dt.c

@@ -20,7 +20,7 @@
 
 #define DA8XX_NUM_UARTS	3
 
-static const struct of_device_id da8xx_irq_match[] __initconst = {
+static const struct of_device_id const da8xx_irq_match[] __initconst = {
 	{ .compatible = "ti,cp-intc", .data = cp_intc_of_init, },
 	{ }
 };
@@ -59,7 +59,7 @@ static void __init da850_init_machine(void)
 
 }
 
-static const char *da850_boards_compat[] __initdata = {
+static const char *const da850_boards_compat[] __initconst = {
 	"enbw,cmc",
 	"ti,da850-evm",
 	"ti,da850",

arch/arm/mach-davinci/time.c

@@ -303,36 +303,42 @@ static int davinci_set_next_event(unsigned long cycles,
 	return 0;
 }
 
-static void davinci_set_mode(enum clock_event_mode mode,
-			     struct clock_event_device *evt)
+static int davinci_shutdown(struct clock_event_device *evt)
 {
 	struct timer_s *t = &timers[TID_CLOCKEVENT];
 
-	switch (mode) {
-	case CLOCK_EVT_MODE_PERIODIC:
-		t->period = davinci_clock_tick_rate / (HZ);
-		t->opts &= ~TIMER_OPTS_STATE_MASK;
-		t->opts |= TIMER_OPTS_PERIODIC;
-		timer32_config(t);
-		break;
-	case CLOCK_EVT_MODE_ONESHOT:
-		t->opts &= ~TIMER_OPTS_STATE_MASK;
-		t->opts |= TIMER_OPTS_ONESHOT;
-		break;
-	case CLOCK_EVT_MODE_UNUSED:
-	case CLOCK_EVT_MODE_SHUTDOWN:
-		t->opts &= ~TIMER_OPTS_STATE_MASK;
-		t->opts |= TIMER_OPTS_DISABLED;
-		break;
-	case CLOCK_EVT_MODE_RESUME:
-		break;
-	}
+	t->opts &= ~TIMER_OPTS_STATE_MASK;
+	t->opts |= TIMER_OPTS_DISABLED;
+	return 0;
+}
+
+static int davinci_set_oneshot(struct clock_event_device *evt)
+{
+	struct timer_s *t = &timers[TID_CLOCKEVENT];
+
+	t->opts &= ~TIMER_OPTS_STATE_MASK;
+	t->opts |= TIMER_OPTS_ONESHOT;
+	return 0;
+}
+
+static int davinci_set_periodic(struct clock_event_device *evt)
+{
+	struct timer_s *t = &timers[TID_CLOCKEVENT];
+
+	t->period = davinci_clock_tick_rate / (HZ);
+	t->opts &= ~TIMER_OPTS_STATE_MASK;
+	t->opts |= TIMER_OPTS_PERIODIC;
+	timer32_config(t);
+	return 0;
 }
 
 static struct clock_event_device clockevent_davinci = {
-	.features       = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
-	.set_next_event	= davinci_set_next_event,
-	.set_mode	= davinci_set_mode,
+	.features		= CLOCK_EVT_FEAT_PERIODIC |
+				  CLOCK_EVT_FEAT_ONESHOT,
+	.set_next_event		= davinci_set_next_event,
+	.set_state_shutdown	= davinci_shutdown,
+	.set_state_periodic	= davinci_set_periodic,
+	.set_state_oneshot	= davinci_set_oneshot,
 };
 
 

arch/arm/mach-digicolor/digicolor.c

@@ -8,7 +8,7 @@
 
 #include <asm/mach/arch.h>
 
-static const char *digicolor_dt_compat[] __initconst = {
+static const char *const digicolor_dt_compat[] __initconst = {
 	"cnxt,cx92755",
 	NULL,
 };

arch/arm/mach-dove/irq.c

@@ -69,8 +69,9 @@ static struct irq_chip pmu_irq_chip = {
 	.irq_ack	= pmu_irq_ack,
 };
 
-static void pmu_irq_handler(unsigned int irq, struct irq_desc *desc)
+static void pmu_irq_handler(unsigned int __irq, struct irq_desc *desc)
 {
+	unsigned int irq = irq_desc_get_irq(desc);
 	unsigned long cause = readl(PMU_INTERRUPT_CAUSE);
 
 	cause &= readl(PMU_INTERRUPT_MASK);
@@ -172,7 +173,7 @@ void __init dove_init_irq(void)
 	for (i = IRQ_DOVE_PMU_START; i < NR_IRQS; i++) {
 		irq_set_chip_and_handler(i, &pmu_irq_chip, handle_level_irq);
 		irq_set_status_flags(i, IRQ_LEVEL);
-		set_irq_flags(i, IRQF_VALID);
+		irq_clear_status_flags(i, IRQ_NOREQUEST);
 	}
 	irq_set_chained_handler(IRQ_DOVE_PMU, pmu_irq_handler);
 }

arch/arm/mach-ebsa110/core.c

@@ -65,7 +65,7 @@ static void __init ebsa110_init_irq(void)
 	for (irq = 0; irq < NR_IRQS; irq++) {
 		irq_set_chip_and_handler(irq, &ebsa110_irq_chip,
 					 handle_level_irq);
-		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+		irq_clear_status_flags(irq, IRQ_NOREQUEST | IRQ_NOPROBE);
 	}
 }
 

arch/arm/mach-ep93xx/Kconfig

@@ -15,45 +15,8 @@ config CRUNCH
 
 comment "EP93xx Platforms"
 
-choice
-	prompt "EP93xx first SDRAM bank selection"
-	default EP93XX_SDCE3_SYNC_PHYS_OFFSET
-
-config EP93XX_SDCE3_SYNC_PHYS_OFFSET
-	bool "0x00000000 - SDCE3/SyncBoot"
-	help
-	  Select this option if you want support for EP93xx boards with the
-	  first SDRAM bank at 0x00000000.
-
-config EP93XX_SDCE0_PHYS_OFFSET
-	bool "0xc0000000 - SDCEO"
-	help
-	  Select this option if you want support for EP93xx boards with the
-	  first SDRAM bank at 0xc0000000.
-
-config EP93XX_SDCE1_PHYS_OFFSET
-	bool "0xd0000000 - SDCE1"
-	help
-	  Select this option if you want support for EP93xx boards with the
-	  first SDRAM bank at 0xd0000000.
-
-config EP93XX_SDCE2_PHYS_OFFSET
-	bool "0xe0000000 - SDCE2"
-	help
-	  Select this option if you want support for EP93xx boards with the
-	  first SDRAM bank at 0xe0000000.
-
-config EP93XX_SDCE3_ASYNC_PHYS_OFFSET
-	bool "0xf0000000 - SDCE3/AsyncBoot"
-	help
-	  Select this option if you want support for EP93xx boards with the
-	  first SDRAM bank at 0xf0000000.
-
-endchoice
-
 config MACH_ADSSPHERE
 	bool "Support ADS Sphere"
-	depends on EP93XX_SDCE3_SYNC_PHYS_OFFSET
 	help
 	  Say 'Y' here if you want your kernel to support the ADS
 	  Sphere board.
@@ -63,7 +26,6 @@ config MACH_EDB93XX
 
 config MACH_EDB9301
 	bool "Support Cirrus Logic EDB9301"
-	depends on EP93XX_SDCE3_SYNC_PHYS_OFFSET
 	select MACH_EDB93XX
 	help
 	  Say 'Y' here if you want your kernel to support the Cirrus
@@ -71,7 +33,6 @@ config MACH_EDB9301
 
 config MACH_EDB9302
 	bool "Support Cirrus Logic EDB9302"
-	depends on EP93XX_SDCE3_SYNC_PHYS_OFFSET
 	select MACH_EDB93XX
 	help
 	  Say 'Y' here if you want your kernel to support the Cirrus
@@ -79,7 +40,6 @@ config MACH_EDB9302
 
 config MACH_EDB9302A
 	bool "Support Cirrus Logic EDB9302A"
-	depends on EP93XX_SDCE0_PHYS_OFFSET
 	select MACH_EDB93XX
 	help
 	  Say 'Y' here if you want your kernel to support the Cirrus
@@ -87,7 +47,6 @@ config MACH_EDB9302A
 
 config MACH_EDB9307
 	bool "Support Cirrus Logic EDB9307"
-	depends on EP93XX_SDCE3_SYNC_PHYS_OFFSET
 	select MACH_EDB93XX
 	help
 	  Say 'Y' here if you want your kernel to support the Cirrus
@@ -95,7 +54,6 @@ config MACH_EDB9307
 
 config MACH_EDB9307A
 	bool "Support Cirrus Logic EDB9307A"
-	depends on EP93XX_SDCE0_PHYS_OFFSET
 	select MACH_EDB93XX
 	help
 	  Say 'Y' here if you want your kernel to support the Cirrus
@@ -103,7 +61,6 @@ config MACH_EDB9307A
 
 config MACH_EDB9312
 	bool "Support Cirrus Logic EDB9312"
-	depends on EP93XX_SDCE3_SYNC_PHYS_OFFSET
 	select MACH_EDB93XX
 	help
 	  Say 'Y' here if you want your kernel to support the Cirrus
@@ -111,7 +68,6 @@ config MACH_EDB9312
 
 config MACH_EDB9315
 	bool "Support Cirrus Logic EDB9315"
-	depends on EP93XX_SDCE3_SYNC_PHYS_OFFSET
 	select MACH_EDB93XX
 	help
 	  Say 'Y' here if you want your kernel to support the Cirrus
@@ -119,14 +75,12 @@ config MACH_EDB9315
 
 config MACH_EDB9315A
 	bool "Support Cirrus Logic EDB9315A"
-	depends on EP93XX_SDCE0_PHYS_OFFSET
 	select MACH_EDB93XX
 	help
 	  Say 'Y' here if you want your kernel to support the Cirrus
 	  Logic EDB9315A Evaluation Board.
 
 config MACH_GESBC9312
-	depends on EP93XX_SDCE3_SYNC_PHYS_OFFSET
 	bool "Support Glomation GESBC-9312-sx"
 	help
 	  Say 'Y' here if you want your kernel to support the Glomation
@@ -137,7 +91,6 @@ config MACH_MICRO9
 
 config MACH_MICRO9H
 	bool "Support Contec Micro9-High"
-	depends on EP93XX_SDCE3_SYNC_PHYS_OFFSET
 	select MACH_MICRO9
 	help
 	  Say 'Y' here if you want your kernel to support the
@@ -145,7 +98,6 @@ config MACH_MICRO9H
 
 config MACH_MICRO9M
 	bool "Support Contec Micro9-Mid"
-	depends on EP93XX_SDCE3_ASYNC_PHYS_OFFSET
 	select MACH_MICRO9
 	help
 	  Say 'Y' here if you want your kernel to support the
@@ -153,7 +105,6 @@ config MACH_MICRO9M
 
 config MACH_MICRO9L
 	bool "Support Contec Micro9-Lite"
-	depends on EP93XX_SDCE3_SYNC_PHYS_OFFSET
 	select MACH_MICRO9
 	help
 	  Say 'Y' here if you want your kernel to support the
@@ -161,7 +112,6 @@ config MACH_MICRO9L
 
 config MACH_MICRO9S
 	bool "Support Contec Micro9-Slim"
-	depends on EP93XX_SDCE3_ASYNC_PHYS_OFFSET
 	select MACH_MICRO9
 	help
 	  Say 'Y' here if you want your kernel to support the
@@ -169,28 +119,24 @@ config MACH_MICRO9S
 
 config MACH_SIM_ONE
         bool "Support Simplemachines Sim.One board"
-        depends on EP93XX_SDCE0_PHYS_OFFSET
         help
           Say 'Y' here if you want your kernel to support the
           Simplemachines Sim.One board.
 
 config MACH_SNAPPER_CL15
 	bool "Support Bluewater Systems Snapper CL15 Module"
-	depends on EP93XX_SDCE0_PHYS_OFFSET
 	help
 	  Say 'Y' here if you want your kernel to support the Bluewater
 	  Systems Snapper CL15 Module.
 
 config MACH_TS72XX
 	bool "Support Technologic Systems TS-72xx SBC"
-	depends on EP93XX_SDCE3_SYNC_PHYS_OFFSET
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Technologic Systems TS-72xx board.
 
 config MACH_VISION_EP9307
 	bool "Support Vision Engraving Systems EP9307 SoM"
-	depends on EP93XX_SDCE0_PHYS_OFFSET
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Vision Engraving Systems EP9307 SoM.

arch/arm/mach-ep93xx/Makefile

@@ -1,7 +1,7 @@
 #
 # Makefile for the linux kernel.
 #
-obj-y			:= core.o clock.o
+obj-y			:= core.o clock.o timer-ep93xx.o
 
 obj-$(CONFIG_EP93XX_DMA)	+= dma.o
 

arch/arm/mach-ep93xx/Makefile.boot

@@ -1,14 +1 @@
-   zreladdr-$(CONFIG_EP93XX_SDCE3_SYNC_PHYS_OFFSET)	+= 0x00008000
-params_phys-$(CONFIG_EP93XX_SDCE3_SYNC_PHYS_OFFSET)	:= 0x00000100
-
-   zreladdr-$(CONFIG_EP93XX_SDCE0_PHYS_OFFSET)		+= 0xc0008000
-params_phys-$(CONFIG_EP93XX_SDCE0_PHYS_OFFSET)		:= 0xc0000100
-
-   zreladdr-$(CONFIG_EP93XX_SDCE1_PHYS_OFFSET)		+= 0xd0008000
-params_phys-$(CONFIG_EP93XX_SDCE1_PHYS_OFFSET)		:= 0xd0000100
-
-   zreladdr-$(CONFIG_EP93XX_SDCE2_PHYS_OFFSET)		+= 0xe0008000
-params_phys-$(CONFIG_EP93XX_SDCE2_PHYS_OFFSET)		:= 0xe0000100
-
-   zreladdr-$(CONFIG_EP93XX_SDCE3_ASYNC_PHYS_OFFSET)	+= 0xf0008000
-params_phys-$(CONFIG_EP93XX_SDCE3_ASYNC_PHYS_OFFSET)	:= 0xf0000100
+# Empty file waiting for deletion once Makefile.boot isn't needed any more.

arch/arm/mach-ep93xx/core.c

@@ -22,7 +22,6 @@
 #include <linux/interrupt.h>
 #include <linux/dma-mapping.h>
 #include <linux/sys_soc.h>
-#include <linux/timex.h>
 #include <linux/irq.h>
 #include <linux/io.h>
 #include <linux/gpio.h>
@@ -38,6 +37,7 @@
 #include <linux/irqchip/arm-vic.h>
 #include <linux/reboot.h>
 #include <linux/usb/ohci_pdriver.h>
+#include <linux/random.h>
 
 #include <mach/hardware.h>
 #include <linux/platform_data/video-ep93xx.h>
@@ -47,7 +47,6 @@
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
-#include <asm/mach/time.h>
 
 #include "soc.h"
 
@@ -73,113 +72,6 @@ void __init ep93xx_map_io(void)
 	iotable_init(ep93xx_io_desc, ARRAY_SIZE(ep93xx_io_desc));
 }
 
-
-/*************************************************************************
- * Timer handling for EP93xx
- *************************************************************************
- * The ep93xx has four internal timers.  Timers 1, 2 (both 16 bit) and
- * 3 (32 bit) count down at 508 kHz, are self-reloading, and can generate
- * an interrupt on underflow.  Timer 4 (40 bit) counts down at 983.04 kHz,
- * is free-running, and can't generate interrupts.
- *
- * The 508 kHz timers are ideal for use for the timer interrupt, as the
- * most common values of HZ divide 508 kHz nicely.  We pick one of the 16
- * bit timers (timer 1) since we don't need more than 16 bits of reload
- * value as long as HZ >= 8.
- *
- * The higher clock rate of timer 4 makes it a better choice than the
- * other timers for use in gettimeoffset(), while the fact that it can't
- * generate interrupts means we don't have to worry about not being able
- * to use this timer for something else.  We also use timer 4 for keeping
- * track of lost jiffies.
- */
-#define EP93XX_TIMER_REG(x)		(EP93XX_TIMER_BASE + (x))
-#define EP93XX_TIMER1_LOAD		EP93XX_TIMER_REG(0x00)
-#define EP93XX_TIMER1_VALUE		EP93XX_TIMER_REG(0x04)
-#define EP93XX_TIMER1_CONTROL		EP93XX_TIMER_REG(0x08)
-#define EP93XX_TIMER123_CONTROL_ENABLE	(1 << 7)
-#define EP93XX_TIMER123_CONTROL_MODE	(1 << 6)
-#define EP93XX_TIMER123_CONTROL_CLKSEL	(1 << 3)
-#define EP93XX_TIMER1_CLEAR		EP93XX_TIMER_REG(0x0c)
-#define EP93XX_TIMER2_LOAD		EP93XX_TIMER_REG(0x20)
-#define EP93XX_TIMER2_VALUE		EP93XX_TIMER_REG(0x24)
-#define EP93XX_TIMER2_CONTROL		EP93XX_TIMER_REG(0x28)
-#define EP93XX_TIMER2_CLEAR		EP93XX_TIMER_REG(0x2c)
-#define EP93XX_TIMER4_VALUE_LOW		EP93XX_TIMER_REG(0x60)
-#define EP93XX_TIMER4_VALUE_HIGH	EP93XX_TIMER_REG(0x64)
-#define EP93XX_TIMER4_VALUE_HIGH_ENABLE	(1 << 8)
-#define EP93XX_TIMER3_LOAD		EP93XX_TIMER_REG(0x80)
-#define EP93XX_TIMER3_VALUE		EP93XX_TIMER_REG(0x84)
-#define EP93XX_TIMER3_CONTROL		EP93XX_TIMER_REG(0x88)
-#define EP93XX_TIMER3_CLEAR		EP93XX_TIMER_REG(0x8c)
-
-#define EP93XX_TIMER123_CLOCK		508469
-#define EP93XX_TIMER4_CLOCK		983040
-
-#define TIMER1_RELOAD			((EP93XX_TIMER123_CLOCK / HZ) - 1)
-#define TIMER4_TICKS_PER_JIFFY		DIV_ROUND_CLOSEST(EP93XX_TIMER4_CLOCK, HZ)
-
-static unsigned int last_jiffy_time;
-
-static irqreturn_t ep93xx_timer_interrupt(int irq, void *dev_id)
-{
-	/* Writing any value clears the timer interrupt */
-	__raw_writel(1, EP93XX_TIMER1_CLEAR);
-
-	/* Recover lost jiffies */
-	while ((signed long)
-		(__raw_readl(EP93XX_TIMER4_VALUE_LOW) - last_jiffy_time)
-						>= TIMER4_TICKS_PER_JIFFY) {
-		last_jiffy_time += TIMER4_TICKS_PER_JIFFY;
-		timer_tick();
-	}
-
-	return IRQ_HANDLED;
-}
-
-static struct irqaction ep93xx_timer_irq = {
-	.name		= "ep93xx timer",
-	.flags		= IRQF_TIMER | IRQF_IRQPOLL,
-	.handler	= ep93xx_timer_interrupt,
-};
-
-static u32 ep93xx_gettimeoffset(void)
-{
-	int offset;
-
-	offset = __raw_readl(EP93XX_TIMER4_VALUE_LOW) - last_jiffy_time;
-
-	/*
-	 * Timer 4 is based on a 983.04 kHz reference clock,
-	 * so dividing by 983040 gives the fraction of a second,
-	 * so dividing by 0.983040 converts to uS.
-	 * Refactor the calculation to avoid overflow.
-	 * Finally, multiply by 1000 to give nS.
-	 */
-	return (offset + (53 * offset / 3072)) * 1000;
-}
-
-void __init ep93xx_timer_init(void)
-{
-	u32 tmode = EP93XX_TIMER123_CONTROL_MODE |
-		    EP93XX_TIMER123_CONTROL_CLKSEL;
-
-	arch_gettimeoffset = ep93xx_gettimeoffset;
-
-	/* Enable periodic HZ timer.  */
-	__raw_writel(tmode, EP93XX_TIMER1_CONTROL);
-	__raw_writel(TIMER1_RELOAD, EP93XX_TIMER1_LOAD);
-	__raw_writel(tmode | EP93XX_TIMER123_CONTROL_ENABLE,
-			EP93XX_TIMER1_CONTROL);
-
-	/* Enable lost jiffy timer.  */
-	__raw_writel(EP93XX_TIMER4_VALUE_HIGH_ENABLE,
-			EP93XX_TIMER4_VALUE_HIGH);
-
-	setup_irq(IRQ_EP93XX_TIMER1, &ep93xx_timer_irq);
-}
-
-
 /*************************************************************************
  * EP93xx IRQ handling
  *************************************************************************/
@@ -971,6 +863,12 @@ static const char __init *ep93xx_get_soc_id(void)
 	if (id != id2)
 		return "invalid";
 
+	/* Toss the unique ID into the entropy pool */
+	add_device_randomness(&id2, 4);
+	add_device_randomness(&id3, 4);
+	add_device_randomness(&id4, 4);
+	add_device_randomness(&id5, 4);
+
 	snprintf(ep93xx_soc_id, sizeof(ep93xx_soc_id),
 		 "%08x%08x%08x%08x", id2, id3, id4, id5);
 

arch/arm/mach-ep93xx/edb93xx.c

@@ -205,8 +205,6 @@ static void __init edb93xx_register_pwm(void)
  * EDB93xx framebuffer
  *************************************************************************/
 static struct ep93xxfb_mach_info __initdata edb93xxfb_info = {
-	.num_modes	= EP93XXFB_USE_MODEDB,
-	.bpp		= 16,
 	.flags		= 0,
 };
 

arch/arm/mach-ep93xx/simone.c

@@ -40,8 +40,6 @@ static struct ep93xx_eth_data __initdata simone_eth_data = {
 };
 
 static struct ep93xxfb_mach_info __initdata simone_fb_info = {
-	.num_modes	= EP93XXFB_USE_MODEDB,
-	.bpp		= 16,
 	.flags		= EP93XXFB_USE_SDCSN0 | EP93XXFB_PCLK_FALLING,
 };
 
@@ -169,6 +167,7 @@ static struct spi_board_info simone_spi_devices[] __initdata = {
 
 static struct ep93xx_spi_info simone_spi_info __initdata = {
 	.num_chipselect	= ARRAY_SIZE(simone_spi_devices),
+	.use_dma = 1,
 };
 
 static struct i2c_gpio_platform_data __initdata simone_i2c_gpio_data = {

arch/arm/mach-ep93xx/snappercl15.c

@@ -144,8 +144,6 @@ static struct i2c_board_info __initdata snappercl15_i2c_data[] = {
 };
 
 static struct ep93xxfb_mach_info __initdata snappercl15_fb_info = {
-	.num_modes		= EP93XXFB_USE_MODEDB,
-	.bpp			= 16,
 };
 
 static struct platform_device snappercl15_audio_device = {

arch/arm/mach-ep93xx/timer-ep93xx.c

@@ -0,0 +1,143 @@
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/clocksource.h>
+#include <linux/clockchips.h>
+#include <linux/sched_clock.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+#include <asm/mach/time.h>
+#include "soc.h"
+
+/*************************************************************************
+ * Timer handling for EP93xx
+ *************************************************************************
+ * The ep93xx has four internal timers.  Timers 1, 2 (both 16 bit) and
+ * 3 (32 bit) count down at 508 kHz, are self-reloading, and can generate
+ * an interrupt on underflow.  Timer 4 (40 bit) counts down at 983.04 kHz,
+ * is free-running, and can't generate interrupts.
+ *
+ * The 508 kHz timers are ideal for use for the timer interrupt, as the
+ * most common values of HZ divide 508 kHz nicely.  We pick the 32 bit
+ * timer (timer 3) to get as long sleep intervals as possible when using
+ * CONFIG_NO_HZ.
+ *
+ * The higher clock rate of timer 4 makes it a better choice than the
+ * other timers for use as clock source and for sched_clock(), providing
+ * a stable 40 bit time base.
+ *************************************************************************
+ */
+#define EP93XX_TIMER_REG(x)		(EP93XX_TIMER_BASE + (x))
+#define EP93XX_TIMER1_LOAD		EP93XX_TIMER_REG(0x00)
+#define EP93XX_TIMER1_VALUE		EP93XX_TIMER_REG(0x04)
+#define EP93XX_TIMER1_CONTROL		EP93XX_TIMER_REG(0x08)
+#define EP93XX_TIMER123_CONTROL_ENABLE	(1 << 7)
+#define EP93XX_TIMER123_CONTROL_MODE	(1 << 6)
+#define EP93XX_TIMER123_CONTROL_CLKSEL	(1 << 3)
+#define EP93XX_TIMER1_CLEAR		EP93XX_TIMER_REG(0x0c)
+#define EP93XX_TIMER2_LOAD		EP93XX_TIMER_REG(0x20)
+#define EP93XX_TIMER2_VALUE		EP93XX_TIMER_REG(0x24)
+#define EP93XX_TIMER2_CONTROL		EP93XX_TIMER_REG(0x28)
+#define EP93XX_TIMER2_CLEAR		EP93XX_TIMER_REG(0x2c)
+#define EP93XX_TIMER4_VALUE_LOW		EP93XX_TIMER_REG(0x60)
+#define EP93XX_TIMER4_VALUE_HIGH	EP93XX_TIMER_REG(0x64)
+#define EP93XX_TIMER4_VALUE_HIGH_ENABLE	(1 << 8)
+#define EP93XX_TIMER3_LOAD		EP93XX_TIMER_REG(0x80)
+#define EP93XX_TIMER3_VALUE		EP93XX_TIMER_REG(0x84)
+#define EP93XX_TIMER3_CONTROL		EP93XX_TIMER_REG(0x88)
+#define EP93XX_TIMER3_CLEAR		EP93XX_TIMER_REG(0x8c)
+
+#define EP93XX_TIMER123_RATE		508469
+#define EP93XX_TIMER4_RATE		983040
+
+static u64 notrace ep93xx_read_sched_clock(void)
+{
+	u64 ret;
+
+	ret = readl(EP93XX_TIMER4_VALUE_LOW);
+	ret |= ((u64) (readl(EP93XX_TIMER4_VALUE_HIGH) & 0xff) << 32);
+	return ret;
+}
+
+cycle_t ep93xx_clocksource_read(struct clocksource *c)
+{
+	u64 ret;
+
+	ret = readl(EP93XX_TIMER4_VALUE_LOW);
+	ret |= ((u64) (readl(EP93XX_TIMER4_VALUE_HIGH) & 0xff) << 32);
+	return (cycle_t) ret;
+}
+
+static int ep93xx_clkevt_set_next_event(unsigned long next,
+					struct clock_event_device *evt)
+{
+	/* Default mode: periodic, off, 508 kHz */
+	u32 tmode = EP93XX_TIMER123_CONTROL_MODE |
+		    EP93XX_TIMER123_CONTROL_CLKSEL;
+
+	/* Clear timer */
+	writel(tmode, EP93XX_TIMER3_CONTROL);
+
+	/* Set next event */
+	writel(next, EP93XX_TIMER3_LOAD);
+	writel(tmode | EP93XX_TIMER123_CONTROL_ENABLE,
+	       EP93XX_TIMER3_CONTROL);
+        return 0;
+}
+
+
+static int ep93xx_clkevt_shutdown(struct clock_event_device *evt)
+{
+	/* Disable timer */
+	writel(0, EP93XX_TIMER3_CONTROL);
+
+	return 0;
+}
+
+static struct clock_event_device ep93xx_clockevent = {
+	.name			= "timer1",
+	.features		= CLOCK_EVT_FEAT_ONESHOT,
+	.set_state_shutdown	= ep93xx_clkevt_shutdown,
+	.set_state_oneshot	= ep93xx_clkevt_shutdown,
+	.tick_resume		= ep93xx_clkevt_shutdown,
+	.set_next_event		= ep93xx_clkevt_set_next_event,
+	.rating			= 300,
+};
+
+static irqreturn_t ep93xx_timer_interrupt(int irq, void *dev_id)
+{
+	struct clock_event_device *evt = dev_id;
+
+	/* Writing any value clears the timer interrupt */
+	writel(1, EP93XX_TIMER3_CLEAR);
+
+	evt->event_handler(evt);
+
+	return IRQ_HANDLED;
+}
+
+static struct irqaction ep93xx_timer_irq = {
+	.name		= "ep93xx timer",
+	.flags		= IRQF_TIMER | IRQF_IRQPOLL,
+	.handler	= ep93xx_timer_interrupt,
+	.dev_id		= &ep93xx_clockevent,
+};
+
+void __init ep93xx_timer_init(void)
+{
+	/* Enable and register clocksource and sched_clock on timer 4 */
+	writel(EP93XX_TIMER4_VALUE_HIGH_ENABLE,
+	       EP93XX_TIMER4_VALUE_HIGH);
+	clocksource_mmio_init(NULL, "timer4",
+			      EP93XX_TIMER4_RATE, 200, 40,
+			      ep93xx_clocksource_read);
+	sched_clock_register(ep93xx_read_sched_clock, 40,
+			     EP93XX_TIMER4_RATE);
+
+	/* Set up clockevent on timer 3 */
+	setup_irq(IRQ_EP93XX_TIMER3, &ep93xx_timer_irq);
+	clockevents_config_and_register(&ep93xx_clockevent,
+					EP93XX_TIMER123_RATE,
+					1,
+					0xffffffffU);
+}

arch/arm/mach-ep93xx/vision_ep9307.c

@@ -29,6 +29,8 @@
 #include <linux/spi/mmc_spi.h>
 #include <linux/mmc/host.h>
 
+#include <sound/cs4271.h>
+
 #include <mach/hardware.h>
 #include <linux/platform_data/video-ep93xx.h>
 #include <linux/platform_data/spi-ep93xx.h>
@@ -104,8 +106,6 @@ static void vision_lcd_blank(int blank_mode, struct fb_info *info)
 }
 
 static struct ep93xxfb_mach_info ep93xxfb_info __initdata = {
-	.num_modes	= EP93XXFB_USE_MODEDB,
-	.bpp		= 16,
 	.flags		= EP93XXFB_USE_SDCSN0 | EP93XXFB_PCLK_FALLING,
 	.setup		= vision_lcd_setup,
 	.teardown	= vision_lcd_teardown,
@@ -168,6 +168,35 @@ static struct i2c_board_info vision_i2c_info[] __initdata = {
 	},
 };
 
+/*************************************************************************
+ * SPI CS4271 Audio Codec
+ *************************************************************************/
+static struct cs4271_platform_data vision_cs4271_data = {
+	.gpio_nreset	= EP93XX_GPIO_LINE_H(2),
+};
+
+static int vision_cs4271_hw_setup(struct spi_device *spi)
+{
+	return gpio_request_one(EP93XX_GPIO_LINE_EGPIO6,
+				GPIOF_OUT_INIT_HIGH, spi->modalias);
+}
+
+static void vision_cs4271_hw_cleanup(struct spi_device *spi)
+{
+	gpio_free(EP93XX_GPIO_LINE_EGPIO6);
+}
+
+static void vision_cs4271_hw_cs_control(struct spi_device *spi, int value)
+{
+	gpio_set_value(EP93XX_GPIO_LINE_EGPIO6, value);
+}
+
+static struct ep93xx_spi_chip_ops vision_cs4271_hw = {
+	.setup		= vision_cs4271_hw_setup,
+	.cleanup	= vision_cs4271_hw_cleanup,
+	.cs_control	= vision_cs4271_hw_cs_control,
+};
+
 /*************************************************************************
  * SPI Flash
  *************************************************************************/
@@ -262,12 +291,20 @@ static struct ep93xx_spi_chip_ops vision_spi_mmc_hw = {
  *************************************************************************/
 static struct spi_board_info vision_spi_board_info[] __initdata = {
 	{
+		.modalias		= "cs4271",
+		.platform_data		= &vision_cs4271_data,
+		.controller_data	= &vision_cs4271_hw,
+		.max_speed_hz		= 6000000,
+		.bus_num		= 0,
+		.chip_select		= 0,
+		.mode			= SPI_MODE_3,
+	}, {
 		.modalias		= "sst25l",
 		.platform_data		= &vision_spi_flash_data,
 		.controller_data	= &vision_spi_flash_hw,
 		.max_speed_hz		= 20000000,
 		.bus_num		= 0,
-		.chip_select		= 0,
+		.chip_select		= 1,
 		.mode			= SPI_MODE_3,
 	}, {
 		.modalias		= "mmc_spi",
@@ -275,15 +312,30 @@ static struct spi_board_info vision_spi_board_info[] __initdata = {
 		.controller_data	= &vision_spi_mmc_hw,
 		.max_speed_hz		= 20000000,
 		.bus_num		= 0,
-		.chip_select		= 1,
+		.chip_select		= 2,
 		.mode			= SPI_MODE_3,
 	},
 };
 
 static struct ep93xx_spi_info vision_spi_master __initdata = {
-	.num_chipselect		= ARRAY_SIZE(vision_spi_board_info),
+	.num_chipselect	= ARRAY_SIZE(vision_spi_board_info),
+	.use_dma	= 1,
 };
 
+/*************************************************************************
+ * I2S Audio
+ *************************************************************************/
+static struct platform_device vision_audio_device = {
+	.name		= "edb93xx-audio",
+	.id		= -1,
+};
+
+static void __init vision_register_i2s(void)
+{
+	ep93xx_register_i2s();
+	platform_device_register(&vision_audio_device);
+}
+
 /*************************************************************************
  * Machine Initialization
  *************************************************************************/
@@ -309,6 +361,7 @@ static void __init vision_init_machine(void)
 				ARRAY_SIZE(vision_i2c_info));
 	ep93xx_register_spi(&vision_spi_master, vision_spi_board_info,
 				ARRAY_SIZE(vision_spi_board_info));
+	vision_register_i2s();
 }
 
 MACHINE_START(VISION_EP9307, "Vision Engraving Systems EP9307")

arch/arm/mach-exynos/Kconfig

@@ -30,6 +30,11 @@ menuconfig ARCH_EXYNOS
 
 if ARCH_EXYNOS
 
+config S5P_DEV_MFC
+	bool
+	help
+	  Compile in setup memory (init) code for MFC
+
 config ARCH_EXYNOS3
 	bool "SAMSUNG EXYNOS3"
 	select ARM_CPU_SUSPEND if PM

arch/arm/mach-exynos/Makefile

@@ -23,3 +23,5 @@ AFLAGS_sleep.o			:=-Wa,-march=armv7-a$(plus_sec)
 
 obj-$(CONFIG_EXYNOS5420_MCPM)	+= mcpm-exynos.o
 CFLAGS_mcpm-exynos.o		+= -march=armv7-a
+
+obj-$(CONFIG_S5P_DEV_MFC)	+= s5p-dev-mfc.o

arch/arm/mach-exynos/common.h

@@ -128,6 +128,12 @@ void exynos_firmware_init(void);
 
 /* CPU BOOT mode flag for Exynos3250 SoC bootloader */
 #define C2_STATE	(1 << 3)
+/*
+ * Magic values for bootloader indicating chosen low power mode.
+ * See also Documentation/arm/Samsung/Bootloader-interface.txt
+ */
+#define EXYNOS_SLEEP_MAGIC	0x00000bad
+#define EXYNOS_AFTR_MAGIC	0xfcba0d10
 
 void exynos_set_boot_flag(unsigned int cpu, unsigned int mode);
 void exynos_clear_boot_flag(unsigned int cpu, unsigned int mode);

arch/arm/mach-exynos/firmware.c

@@ -25,8 +25,6 @@
 #include "common.h"
 #include "smc.h"
 
-#define EXYNOS_SLEEP_MAGIC	0x00000bad
-#define EXYNOS_AFTR_MAGIC	0xfcba0d10
 #define EXYNOS_BOOT_ADDR	0x8
 #define EXYNOS_BOOT_FLAG	0xc
 

arch/arm/mach-exynos/pmu.c

@@ -698,7 +698,7 @@ static void exynos_power_off(void)
 		;
 }
 
-void exynos5420_powerdown_conf(enum sys_powerdown mode)
+static void exynos5420_powerdown_conf(enum sys_powerdown mode)
 {
 	u32 this_cluster;
 
@@ -991,7 +991,6 @@ static int exynos_pmu_probe(struct platform_device *pdev)
 static struct platform_driver exynos_pmu_driver = {
 	.driver  = {
 		.name   = "exynos-pmu",
-		.owner	= THIS_MODULE,
 		.of_match_table = exynos_pmu_of_device_ids,
 	},
 	.probe = exynos_pmu_probe,

arch/arm/plat-samsung/include/plat/regs-srom.h → arch/arm/mach-exynos/regs-srom.h

@@ -1,5 +1,4 @@
-/* linux/arch/arm/plat-samsung/include/plat/regs-srom.h
- *
+/*
  * Copyright (c) 2010 Samsung Electronics Co., Ltd.
  *		http://www.samsung.com
  *

arch/arm/mach-exynos/suspend.c

@@ -32,13 +32,11 @@
 #include <asm/suspend.h>
 
 #include <plat/pm-common.h>
-#include <plat/regs-srom.h>
 
 #include "common.h"
-#include "regs-pmu.h"
 #include "exynos-pmu.h"
-
-#define S5P_CHECK_SLEEP 0x00000BAD
+#include "regs-pmu.h"
+#include "regs-srom.h"
 
 #define REG_TABLE_END (-1U)
 
@@ -331,7 +329,7 @@ static void exynos_pm_enter_sleep_mode(void)
 {
 	/* Set value of power down register for sleep mode */
 	exynos_sys_powerdown_conf(SYS_SLEEP);
-	pmu_raw_writel(S5P_CHECK_SLEEP, S5P_INFORM1);
+	pmu_raw_writel(EXYNOS_SLEEP_MAGIC, S5P_INFORM1);
 }
 
 static void exynos_pm_prepare(void)

arch/arm/mach-footbridge/common.c

@@ -106,7 +106,7 @@ static void __init __fb_init_irq(void)
 
 	for (irq = _DC21285_IRQ(0); irq < _DC21285_IRQ(20); irq++) {
 		irq_set_chip_and_handler(irq, &fb_chip, handle_level_irq);
-		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+		irq_clear_status_flags(irq, IRQ_NOREQUEST | IRQ_NOPROBE);
 	}
 }
 

arch/arm/mach-footbridge/dc21285-timer.c

@@ -57,34 +57,32 @@ static int ckevt_dc21285_set_next_event(unsigned long delta,
 	return 0;
 }
 
-static void ckevt_dc21285_set_mode(enum clock_event_mode mode,
-	struct clock_event_device *c)
+static int ckevt_dc21285_shutdown(struct clock_event_device *c)
 {
-	switch (mode) {
-	case CLOCK_EVT_MODE_RESUME:
-	case CLOCK_EVT_MODE_PERIODIC:
-		*CSR_TIMER1_CLR = 0;
-		*CSR_TIMER1_LOAD = (mem_fclk_21285 + 8 * HZ) / (16 * HZ);
-		*CSR_TIMER1_CNTL = TIMER_CNTL_ENABLE | TIMER_CNTL_AUTORELOAD |
-				   TIMER_CNTL_DIV16;
-		break;
-
-	case CLOCK_EVT_MODE_ONESHOT:
-	case CLOCK_EVT_MODE_UNUSED:
-	case CLOCK_EVT_MODE_SHUTDOWN:
-		*CSR_TIMER1_CNTL = 0;
-		break;
-	}
+	*CSR_TIMER1_CNTL = 0;
+	return 0;
+}
+
+static int ckevt_dc21285_set_periodic(struct clock_event_device *c)
+{
+	*CSR_TIMER1_CLR = 0;
+	*CSR_TIMER1_LOAD = (mem_fclk_21285 + 8 * HZ) / (16 * HZ);
+	*CSR_TIMER1_CNTL = TIMER_CNTL_ENABLE | TIMER_CNTL_AUTORELOAD |
+			   TIMER_CNTL_DIV16;
+	return 0;
 }
 
 static struct clock_event_device ckevt_dc21285 = {
-	.name		= "dc21285_timer1",
-	.features	= CLOCK_EVT_FEAT_PERIODIC |
-			  CLOCK_EVT_FEAT_ONESHOT,
-	.rating		= 200,
-	.irq		= IRQ_TIMER1,
-	.set_next_event	= ckevt_dc21285_set_next_event,
-	.set_mode	= ckevt_dc21285_set_mode,
+	.name			= "dc21285_timer1",
+	.features		= CLOCK_EVT_FEAT_PERIODIC |
+				  CLOCK_EVT_FEAT_ONESHOT,
+	.rating			= 200,
+	.irq			= IRQ_TIMER1,
+	.set_next_event		= ckevt_dc21285_set_next_event,
+	.set_state_shutdown	= ckevt_dc21285_shutdown,
+	.set_state_periodic	= ckevt_dc21285_set_periodic,
+	.set_state_oneshot	= ckevt_dc21285_shutdown,
+	.tick_resume		= ckevt_dc21285_set_periodic,
 };
 
 static irqreturn_t timer1_interrupt(int irq, void *dev_id)
@@ -94,7 +92,7 @@ static irqreturn_t timer1_interrupt(int irq, void *dev_id)
 	*CSR_TIMER1_CLR = 0;
 
 	/* Stop the timer if in one-shot mode */
-	if (ce->mode == CLOCK_EVT_MODE_ONESHOT)
+	if (clockevent_state_oneshot(ce))
 		*CSR_TIMER1_CNTL = 0;
 
 	ce->event_handler(ce);

arch/arm/mach-footbridge/isa-irq.c

@@ -153,13 +153,13 @@ void __init isa_init_irq(unsigned int host_irq)
 		for (irq = _ISA_IRQ(0); irq < _ISA_IRQ(8); irq++) {
 			irq_set_chip_and_handler(irq, &isa_lo_chip,
 						 handle_level_irq);
-			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+			irq_clear_status_flags(irq, IRQ_NOREQUEST | IRQ_NOPROBE);
 		}
 
 		for (irq = _ISA_IRQ(8); irq < _ISA_IRQ(16); irq++) {
 			irq_set_chip_and_handler(irq, &isa_hi_chip,
 						 handle_level_irq);
-			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+			irq_clear_status_flags(irq, IRQ_NOREQUEST | IRQ_NOPROBE);
 		}
 
 		request_resource(&ioport_resource, &pic1_resource);
@@ -175,8 +175,8 @@ void __init isa_init_irq(unsigned int host_irq)
 		 * resistor on this line.
 		 */
 		if (machine_is_netwinder())
-			set_irq_flags(_ISA_IRQ(11), IRQF_VALID |
-				      IRQF_PROBE | IRQF_NOAUTOEN);
+			irq_modify_status(_ISA_IRQ(11),
+				IRQ_NOREQUEST | IRQ_NOPROBE, IRQ_NOAUTOEN);
 	}
 }
 

arch/arm/mach-gemini/gpio.c

@@ -220,7 +220,7 @@ void __init gemini_gpio_init(void)
 		     j < GPIO_IRQ_BASE + (i + 1) * 32; j++) {
 			irq_set_chip_and_handler(j, &gpio_irq_chip,
 						 handle_edge_irq);
-			set_irq_flags(j, IRQF_VALID);
+			irq_clear_status_flags(j, IRQ_NOREQUEST);
 		}
 
 		irq_set_chained_handler_and_data(IRQ_GPIO(i), gpio_irq_handler,

arch/arm/mach-gemini/include/mach/hardware.h

@@ -57,9 +57,6 @@
 #define GEMINI_USB1_BASE	0x69000000
 #define GEMINI_BIG_ENDIAN_BASE	0x80000000
 
-#define GEMINI_TIMER1_BASE	GEMINI_TIMER_BASE
-#define GEMINI_TIMER2_BASE	(GEMINI_TIMER_BASE + 0x10)
-#define GEMINI_TIMER3_BASE	(GEMINI_TIMER_BASE + 0x20)
 
 /*
  * UART Clock when System clk is 150MHz

arch/arm/mach-gemini/irq.c

@@ -92,7 +92,7 @@ void __init gemini_init_irq(void)
 		} else {			
 			irq_set_handler(i, handle_level_irq);
 		}
-		set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
+		irq_clear_status_flags(i, IRQ_NOREQUEST | IRQ_NOPROBE);
 	}
 
 	/* Disable all interrupts */

arch/arm/mach-gemini/time.c

@@ -15,93 +15,147 @@
 #include <asm/mach/time.h>
 #include <linux/clockchips.h>
 #include <linux/clocksource.h>
+#include <linux/sched_clock.h>
 
 /*
  * Register definitions for the timers
  */
-#define TIMER_COUNT(BASE_ADDR)		(BASE_ADDR  + 0x00)
-#define TIMER_LOAD(BASE_ADDR)		(BASE_ADDR  + 0x04)
-#define TIMER_MATCH1(BASE_ADDR)		(BASE_ADDR  + 0x08)
-#define TIMER_MATCH2(BASE_ADDR)		(BASE_ADDR  + 0x0C)
-#define TIMER_CR(BASE_ADDR)		(BASE_ADDR  + 0x30)
-
-#define TIMER_1_CR_ENABLE		(1 << 0)
-#define TIMER_1_CR_CLOCK		(1 << 1)
-#define TIMER_1_CR_INT			(1 << 2)
-#define TIMER_2_CR_ENABLE		(1 << 3)
-#define TIMER_2_CR_CLOCK		(1 << 4)
-#define TIMER_2_CR_INT			(1 << 5)
-#define TIMER_3_CR_ENABLE		(1 << 6)
-#define TIMER_3_CR_CLOCK		(1 << 7)
-#define TIMER_3_CR_INT			(1 << 8)
+
+#define TIMER1_BASE		GEMINI_TIMER_BASE
+#define TIMER2_BASE		(GEMINI_TIMER_BASE + 0x10)
+#define TIMER3_BASE		(GEMINI_TIMER_BASE + 0x20)
+
+#define TIMER_COUNT(BASE)	(IO_ADDRESS(BASE) + 0x00)
+#define TIMER_LOAD(BASE)	(IO_ADDRESS(BASE) + 0x04)
+#define TIMER_MATCH1(BASE)	(IO_ADDRESS(BASE) + 0x08)
+#define TIMER_MATCH2(BASE)	(IO_ADDRESS(BASE) + 0x0C)
+#define TIMER_CR		(IO_ADDRESS(GEMINI_TIMER_BASE) + 0x30)
+#define TIMER_INTR_STATE	(IO_ADDRESS(GEMINI_TIMER_BASE) + 0x34)
+#define TIMER_INTR_MASK		(IO_ADDRESS(GEMINI_TIMER_BASE) + 0x38)
+
+#define TIMER_1_CR_ENABLE	(1 << 0)
+#define TIMER_1_CR_CLOCK	(1 << 1)
+#define TIMER_1_CR_INT		(1 << 2)
+#define TIMER_2_CR_ENABLE	(1 << 3)
+#define TIMER_2_CR_CLOCK	(1 << 4)
+#define TIMER_2_CR_INT		(1 << 5)
+#define TIMER_3_CR_ENABLE	(1 << 6)
+#define TIMER_3_CR_CLOCK	(1 << 7)
+#define TIMER_3_CR_INT		(1 << 8)
+#define TIMER_1_CR_UPDOWN	(1 << 9)
+#define TIMER_2_CR_UPDOWN	(1 << 10)
+#define TIMER_3_CR_UPDOWN	(1 << 11)
+#define TIMER_DEFAULT_FLAGS	(TIMER_1_CR_UPDOWN | \
+				 TIMER_3_CR_ENABLE | \
+				 TIMER_3_CR_UPDOWN)
+
+#define TIMER_1_INT_MATCH1	(1 << 0)
+#define TIMER_1_INT_MATCH2	(1 << 1)
+#define TIMER_1_INT_OVERFLOW	(1 << 2)
+#define TIMER_2_INT_MATCH1	(1 << 3)
+#define TIMER_2_INT_MATCH2	(1 << 4)
+#define TIMER_2_INT_OVERFLOW	(1 << 5)
+#define TIMER_3_INT_MATCH1	(1 << 6)
+#define TIMER_3_INT_MATCH2	(1 << 7)
+#define TIMER_3_INT_OVERFLOW	(1 << 8)
+#define TIMER_INT_ALL_MASK	0x1ff
+
 
 static unsigned int tick_rate;
 
+static u64 notrace gemini_read_sched_clock(void)
+{
+	return readl(TIMER_COUNT(TIMER3_BASE));
+}
+
 static int gemini_timer_set_next_event(unsigned long cycles,
 				       struct clock_event_device *evt)
 {
 	u32 cr;
 
-	cr = readl(TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
+	/* Setup the match register */
+	cr = readl(TIMER_COUNT(TIMER1_BASE));
+	writel(cr + cycles, TIMER_MATCH1(TIMER1_BASE));
+	if (readl(TIMER_COUNT(TIMER1_BASE)) - cr > cycles)
+		return -ETIME;
 
-	/* This may be overdoing it, feel free to test without this */
-	cr &= ~TIMER_2_CR_ENABLE;
-	cr &= ~TIMER_2_CR_INT;
-	writel(cr, TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
+	return 0;
+}
 
-	/* Set next event */
-	writel(cycles, TIMER_COUNT(IO_ADDRESS(GEMINI_TIMER2_BASE)));
-	writel(cycles, TIMER_LOAD(IO_ADDRESS(GEMINI_TIMER2_BASE)));
-	cr |= TIMER_2_CR_ENABLE;
-	cr |= TIMER_2_CR_INT;
-	writel(cr, TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
+static int gemini_timer_shutdown(struct clock_event_device *evt)
+{
+	u32 cr;
+
+	/*
+	 * Disable also for oneshot: the set_next() call will arm the timer
+	 * instead.
+	 */
+	/* Stop timer and interrupt. */
+	cr = readl(TIMER_CR);
+	cr &= ~(TIMER_1_CR_ENABLE | TIMER_1_CR_INT);
+	writel(cr, TIMER_CR);
+
+	/* Setup counter start from 0 */
+	writel(0, TIMER_COUNT(TIMER1_BASE));
+	writel(0, TIMER_LOAD(TIMER1_BASE));
+
+	/* enable interrupt */
+	cr = readl(TIMER_INTR_MASK);
+	cr &= ~(TIMER_1_INT_OVERFLOW | TIMER_1_INT_MATCH2);
+	cr |= TIMER_1_INT_MATCH1;
+	writel(cr, TIMER_INTR_MASK);
+
+	/* start the timer */
+	cr = readl(TIMER_CR);
+	cr |= TIMER_1_CR_ENABLE;
+	writel(cr, TIMER_CR);
 
 	return 0;
 }
 
-static void gemini_timer_set_mode(enum clock_event_mode mode,
-				  struct clock_event_device *evt)
+static int gemini_timer_set_periodic(struct clock_event_device *evt)
 {
 	u32 period = DIV_ROUND_CLOSEST(tick_rate, HZ);
 	u32 cr;
 
-	switch (mode) {
-        case CLOCK_EVT_MODE_PERIODIC:
-		/* Start the timer */
-		writel(period,
-		       TIMER_COUNT(IO_ADDRESS(GEMINI_TIMER2_BASE)));
-		writel(period,
-		       TIMER_LOAD(IO_ADDRESS(GEMINI_TIMER2_BASE)));
-		cr = readl(TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
-		cr |= TIMER_2_CR_ENABLE;
-		cr |= TIMER_2_CR_INT;
-		writel(cr, TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
-		break;
-	case CLOCK_EVT_MODE_ONESHOT:
-	case CLOCK_EVT_MODE_UNUSED:
-        case CLOCK_EVT_MODE_SHUTDOWN:
-	case CLOCK_EVT_MODE_RESUME:
-		/*
-		 * Disable also for oneshot: the set_next() call will
-		 * arm the timer instead.
-		 */
-		cr = readl(TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
-		cr &= ~TIMER_2_CR_ENABLE;
-		cr &= ~TIMER_2_CR_INT;
-		writel(cr, TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
-		break;
-	default:
-                break;
-	}
+	/* Stop timer and interrupt */
+	cr = readl(TIMER_CR);
+	cr &= ~(TIMER_1_CR_ENABLE | TIMER_1_CR_INT);
+	writel(cr, TIMER_CR);
+
+	/* Setup timer to fire at 1/HT intervals. */
+	cr = 0xffffffff - (period - 1);
+	writel(cr, TIMER_COUNT(TIMER1_BASE));
+	writel(cr, TIMER_LOAD(TIMER1_BASE));
+
+	/* enable interrupt on overflow */
+	cr = readl(TIMER_INTR_MASK);
+	cr &= ~(TIMER_1_INT_MATCH1 | TIMER_1_INT_MATCH2);
+	cr |= TIMER_1_INT_OVERFLOW;
+	writel(cr, TIMER_INTR_MASK);
+
+	/* Start the timer */
+	cr = readl(TIMER_CR);
+	cr |= TIMER_1_CR_ENABLE;
+	cr |= TIMER_1_CR_INT;
+	writel(cr, TIMER_CR);
+
+	return 0;
 }
 
-/* Use TIMER2 as clock event */
+/* Use TIMER1 as clock event */
 static struct clock_event_device gemini_clockevent = {
-	.name		= "TIMER2",
-	.rating		= 300, /* Reasonably fast and accurate clock event */
-	.features	= CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
-	.set_next_event	= gemini_timer_set_next_event,
-	.set_mode	= gemini_timer_set_mode,
+	.name			= "TIMER1",
+	/* Reasonably fast and accurate clock event */
+	.rating			= 300,
+	.shift                  = 32,
+	.features		= CLOCK_EVT_FEAT_PERIODIC |
+				  CLOCK_EVT_FEAT_ONESHOT,
+	.set_next_event		= gemini_timer_set_next_event,
+	.set_state_shutdown	= gemini_timer_shutdown,
+	.set_state_periodic	= gemini_timer_set_periodic,
+	.set_state_oneshot	= gemini_timer_shutdown,
+	.tick_resume		= gemini_timer_shutdown,
 };
 
 /*
@@ -151,20 +205,35 @@ void __init gemini_timer_init(void)
 	}
 
 	/*
-	 * Make irqs happen for the system timer
+	 * Reset the interrupt mask and status
 	 */
-	setup_irq(IRQ_TIMER2, &gemini_timer_irq);
-
-	/* Enable and use TIMER1 as clock source */
-	writel(0xffffffff, TIMER_COUNT(IO_ADDRESS(GEMINI_TIMER1_BASE)));
-	writel(0xffffffff, TIMER_LOAD(IO_ADDRESS(GEMINI_TIMER1_BASE)));
-	writel(TIMER_1_CR_ENABLE, TIMER_CR(IO_ADDRESS(GEMINI_TIMER_BASE)));
-	if (clocksource_mmio_init(TIMER_COUNT(IO_ADDRESS(GEMINI_TIMER1_BASE)),
-				  "TIMER1", tick_rate, 300, 32,
-				  clocksource_mmio_readl_up))
-		pr_err("timer: failed to initialize gemini clock source\n");
-
-	/* Configure and register the clockevent */
+	writel(TIMER_INT_ALL_MASK, TIMER_INTR_MASK);
+	writel(0, TIMER_INTR_STATE);
+	writel(TIMER_DEFAULT_FLAGS, TIMER_CR);
+
+	/*
+	 * Setup free-running clocksource timer (interrupts
+	 * disabled.)
+	 */
+	writel(0, TIMER_COUNT(TIMER3_BASE));
+	writel(0, TIMER_LOAD(TIMER3_BASE));
+	writel(0, TIMER_MATCH1(TIMER3_BASE));
+	writel(0, TIMER_MATCH2(TIMER3_BASE));
+	clocksource_mmio_init(TIMER_COUNT(TIMER3_BASE),
+			      "gemini_clocksource", tick_rate,
+			      300, 32, clocksource_mmio_readl_up);
+	sched_clock_register(gemini_read_sched_clock, 32, tick_rate);
+
+	/*
+	 * Setup clockevent timer (interrupt-driven.)
+	*/
+	writel(0, TIMER_COUNT(TIMER1_BASE));
+	writel(0, TIMER_LOAD(TIMER1_BASE));
+	writel(0, TIMER_MATCH1(TIMER1_BASE));
+	writel(0, TIMER_MATCH2(TIMER1_BASE));
+	setup_irq(IRQ_TIMER1, &gemini_timer_irq);
+	gemini_clockevent.cpumask = cpumask_of(0);
 	clockevents_config_and_register(&gemini_clockevent, tick_rate,
 					1, 0xffffffff);
+
 }

arch/arm/mach-imx/3ds_debugboard.c

@@ -195,7 +195,7 @@ int __init mxc_expio_init(u32 base, u32 intr_gpio)
 
 	for (i = irq_base; i < irq_base + MXC_MAX_EXP_IO_LINES; i++) {
 		irq_set_chip_and_handler(i, &expio_irq_chip, handle_level_irq);
-		set_irq_flags(i, IRQF_VALID);
+		irq_clear_status_flags(i, IRQ_NOREQUEST);
 	}
 	irq_set_irq_type(p_irq, IRQF_TRIGGER_LOW);
 	irq_set_chained_handler(p_irq, mxc_expio_irq_handler);

arch/arm/mach-imx/epit.c

@@ -57,7 +57,6 @@
 #include "hardware.h"
 
 static struct clock_event_device clockevent_epit;
-static enum clock_event_mode clockevent_mode = CLOCK_EVT_MODE_UNUSED;
 
 static void __iomem *timer_base;
 
@@ -106,8 +105,8 @@ static int epit_set_next_event(unsigned long evt,
 	return 0;
 }
 
-static void epit_set_mode(enum clock_event_mode mode,
-				struct clock_event_device *evt)
+/* Left event sources disabled, no more interrupts appear */
+static int epit_shutdown(struct clock_event_device *evt)
 {
 	unsigned long flags;
 
@@ -120,39 +119,41 @@ static void epit_set_mode(enum clock_event_mode mode,
 	/* Disable interrupt in GPT module */
 	epit_irq_disable();
 
-	if (mode != clockevent_mode) {
-		/* Set event time into far-far future */
-
-		/* Clear pending interrupt */
-		epit_irq_acknowledge();
-	}
+	/* Clear pending interrupt */
+	epit_irq_acknowledge();
 
-	/* Remember timer mode */
-	clockevent_mode = mode;
 	local_irq_restore(flags);
 
-	switch (mode) {
-	case CLOCK_EVT_MODE_PERIODIC:
-		printk(KERN_ERR "epit_set_mode: Periodic mode is not "
-				"supported for i.MX EPIT\n");
-		break;
-	case CLOCK_EVT_MODE_ONESHOT:
+	return 0;
+}
+
+static int epit_set_oneshot(struct clock_event_device *evt)
+{
+	unsigned long flags;
+
+	/*
+	 * The timer interrupt generation is disabled at least
+	 * for enough time to call epit_set_next_event()
+	 */
+	local_irq_save(flags);
+
+	/* Disable interrupt in GPT module */
+	epit_irq_disable();
+
+	/* Clear pending interrupt, only while switching mode */
+	if (!clockevent_state_oneshot(evt))
+		epit_irq_acknowledge();
+
 	/*
 	 * Do not put overhead of interrupt enable/disable into
 	 * epit_set_next_event(), the core has about 4 minutes
 	 * to call epit_set_next_event() or shutdown clock after
 	 * mode switching
 	 */
-		local_irq_save(flags);
-		epit_irq_enable();
-		local_irq_restore(flags);
-		break;
-	case CLOCK_EVT_MODE_SHUTDOWN:
-	case CLOCK_EVT_MODE_UNUSED:
-	case CLOCK_EVT_MODE_RESUME:
-		/* Left event sources disabled, no more interrupts appear */
-		break;
-	}
+	epit_irq_enable();
+	local_irq_restore(flags);
+
+	return 0;
 }
 
 /*
@@ -176,11 +177,13 @@ static struct irqaction epit_timer_irq = {
 };
 
 static struct clock_event_device clockevent_epit = {
-	.name		= "epit",
-	.features	= CLOCK_EVT_FEAT_ONESHOT,
-	.set_mode	= epit_set_mode,
-	.set_next_event	= epit_set_next_event,
-	.rating		= 200,
+	.name			= "epit",
+	.features		= CLOCK_EVT_FEAT_ONESHOT,
+	.set_state_shutdown	= epit_shutdown,
+	.tick_resume		= epit_shutdown,
+	.set_state_oneshot	= epit_set_oneshot,
+	.set_next_event		= epit_set_next_event,
+	.rating			= 200,
 };
 
 static int __init epit_clockevent_init(struct clk *timer_clk)

arch/arm/mach-imx/mach-imx7d.c

@@ -31,7 +31,7 @@ static void __init imx7d_init_irq(void)
 	irqchip_init();
 }
 
-static const char *imx7d_dt_compat[] __initconst = {
+static const char *const imx7d_dt_compat[] __initconst = {
 	"fsl,imx7d",
 	NULL,
 };

arch/arm/mach-imx/mach-mx31ads.c

@@ -238,7 +238,7 @@ static void __init mx31ads_init_expio(void)
 
 	for (i = irq_base; i < irq_base + MXC_MAX_EXP_IO_LINES; i++) {
 		irq_set_chip_and_handler(i, &expio_irq_chip, handle_level_irq);
-		set_irq_flags(i, IRQF_VALID);
+		irq_clear_status_flags(i, IRQ_NOREQUEST);
 	}
 	irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_4));
 	irq_set_irq_type(irq, IRQ_TYPE_LEVEL_HIGH);

arch/arm/mach-iop13xx/irq.c

@@ -233,7 +233,7 @@ void __init iop13xx_init_irq(void)
 			irq_set_chip(i, &iop13xx_irqchip4);
 
 		irq_set_handler(i, handle_level_irq);
-		set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
+		irq_clear_status_flags(i, IRQ_NOREQUEST | IRQ_NOPROBE);
 	}
 
 	iop13xx_msi_init();

arch/arm/mach-iop32x/irq.c

@@ -69,6 +69,6 @@ void __init iop32x_init_irq(void)
 
 	for (i = 0; i < NR_IRQS; i++) {
 		irq_set_chip_and_handler(i, &ext_chip, handle_level_irq);
-		set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
+		irq_clear_status_flags(i, IRQ_NOREQUEST | IRQ_NOPROBE);
 	}
 }

arch/arm/mach-iop33x/irq.c

@@ -113,6 +113,6 @@ void __init iop33x_init_irq(void)
 		irq_set_chip_and_handler(i,
 					 (i < 32) ? &iop33x_irqchip1 : &iop33x_irqchip2,
 					 handle_level_irq);
-		set_irq_flags(i, IRQF_VALID | IRQF_PROBE);
+		irq_clear_status_flags(i, IRQ_NOREQUEST | IRQ_NOPROBE);
 	}
 }

arch/arm/mach-ixp4xx/common.c

@@ -296,7 +296,7 @@ void __init ixp4xx_init_irq(void)
 	for(i = 0; i < NR_IRQS; i++) {
 		irq_set_chip_and_handler(i, &ixp4xx_irq_chip,
 					 handle_level_irq);
-		set_irq_flags(i, IRQF_VALID);
+		irq_clear_status_flags(i, IRQ_NOREQUEST);
 	}
 }
 
@@ -521,43 +521,55 @@ static int ixp4xx_set_next_event(unsigned long evt,
 	return 0;
 }
 
-static void ixp4xx_set_mode(enum clock_event_mode mode,
-			    struct clock_event_device *evt)
+static int ixp4xx_shutdown(struct clock_event_device *evt)
 {
 	unsigned long opts = *IXP4XX_OSRT1 & IXP4XX_OST_RELOAD_MASK;
 	unsigned long osrt = *IXP4XX_OSRT1 & ~IXP4XX_OST_RELOAD_MASK;
 
-	switch (mode) {
-	case CLOCK_EVT_MODE_PERIODIC:
-		osrt = IXP4XX_LATCH & ~IXP4XX_OST_RELOAD_MASK;
- 		opts = IXP4XX_OST_ENABLE;
-		break;
-	case CLOCK_EVT_MODE_ONESHOT:
-		/* period set by 'set next_event' */
-		osrt = 0;
-		opts = IXP4XX_OST_ENABLE | IXP4XX_OST_ONE_SHOT;
-		break;
-	case CLOCK_EVT_MODE_SHUTDOWN:
-		opts &= ~IXP4XX_OST_ENABLE;
-		break;
-	case CLOCK_EVT_MODE_RESUME:
-		opts |= IXP4XX_OST_ENABLE;
-		break;
-	case CLOCK_EVT_MODE_UNUSED:
-	default:
-		osrt = opts = 0;
-		break;
-	}
+	opts &= ~IXP4XX_OST_ENABLE;
+	*IXP4XX_OSRT1 = osrt | opts;
+	return 0;
+}
 
+static int ixp4xx_set_oneshot(struct clock_event_device *evt)
+{
+	unsigned long opts = IXP4XX_OST_ENABLE | IXP4XX_OST_ONE_SHOT;
+	unsigned long osrt = 0;
+
+	/* period set by 'set next_event' */
 	*IXP4XX_OSRT1 = osrt | opts;
+	return 0;
+}
+
+static int ixp4xx_set_periodic(struct clock_event_device *evt)
+{
+	unsigned long opts = IXP4XX_OST_ENABLE;
+	unsigned long osrt = IXP4XX_LATCH & ~IXP4XX_OST_RELOAD_MASK;
+
+	*IXP4XX_OSRT1 = osrt | opts;
+	return 0;
+}
+
+static int ixp4xx_resume(struct clock_event_device *evt)
+{
+	unsigned long opts = *IXP4XX_OSRT1 & IXP4XX_OST_RELOAD_MASK;
+	unsigned long osrt = *IXP4XX_OSRT1 & ~IXP4XX_OST_RELOAD_MASK;
+
+	opts |= IXP4XX_OST_ENABLE;
+	*IXP4XX_OSRT1 = osrt | opts;
+	return 0;
 }
 
 static struct clock_event_device clockevent_ixp4xx = {
-	.name		= "ixp4xx timer1",
-	.features       = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
-	.rating         = 200,
-	.set_mode	= ixp4xx_set_mode,
-	.set_next_event	= ixp4xx_set_next_event,
+	.name			= "ixp4xx timer1",
+	.features		= CLOCK_EVT_FEAT_PERIODIC |
+				  CLOCK_EVT_FEAT_ONESHOT,
+	.rating			= 200,
+	.set_state_shutdown	= ixp4xx_shutdown,
+	.set_state_periodic	= ixp4xx_set_periodic,
+	.set_state_oneshot	= ixp4xx_set_oneshot,
+	.tick_resume		= ixp4xx_resume,
+	.set_next_event		= ixp4xx_set_next_event,
 };
 
 static void __init ixp4xx_clockevent_init(void)

arch/arm/mach-ks8695/irq.c

@@ -172,6 +172,6 @@ void __init ks8695_init_irq(void)
 							 handle_edge_irq);
 		}
 
-		set_irq_flags(irq, IRQF_VALID);
+		irq_clear_status_flags(irq, IRQ_NOREQUEST);
 	}
 }

arch/arm/mach-ks8695/time.c

@@ -54,28 +54,25 @@
 /* Timer0 Timeout Counter Register */
 #define T0TC_WATCHDOG		(0xff)		/* Enable watchdog mode */
 
-static void ks8695_set_mode(enum clock_event_mode mode,
-			    struct clock_event_device *evt)
+static int ks8695_set_periodic(struct clock_event_device *evt)
 {
+	u32 rate = DIV_ROUND_CLOSEST(KS8695_CLOCK_RATE, HZ);
+	u32 half = DIV_ROUND_CLOSEST(rate, 2);
 	u32 tmcon;
 
-	if (mode == CLOCK_EVT_FEAT_PERIODIC) {
-		u32 rate = DIV_ROUND_CLOSEST(KS8695_CLOCK_RATE, HZ);
-		u32 half = DIV_ROUND_CLOSEST(rate, 2);
-
-		/* Disable timer 1 */
-		tmcon = readl_relaxed(KS8695_TMR_VA + KS8695_TMCON);
-		tmcon &= ~TMCON_T1EN;
-		writel_relaxed(tmcon, KS8695_TMR_VA + KS8695_TMCON);
+	/* Disable timer 1 */
+	tmcon = readl_relaxed(KS8695_TMR_VA + KS8695_TMCON);
+	tmcon &= ~TMCON_T1EN;
+	writel_relaxed(tmcon, KS8695_TMR_VA + KS8695_TMCON);
 
-		/* Both registers need to count down */
-		writel_relaxed(half, KS8695_TMR_VA + KS8695_T1TC);
-		writel_relaxed(half, KS8695_TMR_VA + KS8695_T1PD);
+	/* Both registers need to count down */
+	writel_relaxed(half, KS8695_TMR_VA + KS8695_T1TC);
+	writel_relaxed(half, KS8695_TMR_VA + KS8695_T1PD);
 
-		/* Re-enable timer1 */
-		tmcon |= TMCON_T1EN;
-		writel_relaxed(tmcon, KS8695_TMR_VA + KS8695_TMCON);
-	}
+	/* Re-enable timer1 */
+	tmcon |= TMCON_T1EN;
+	writel_relaxed(tmcon, KS8695_TMR_VA + KS8695_TMCON);
+	return 0;
 }
 
 static int ks8695_set_next_event(unsigned long cycles,
@@ -102,11 +99,13 @@ static int ks8695_set_next_event(unsigned long cycles,
 }
 
 static struct clock_event_device clockevent_ks8695 = {
-	.name		= "ks8695_t1tc",
-	.rating		= 300, /* Reasonably fast and accurate clock event */
-	.features	= CLOCK_EVT_FEAT_ONESHOT | CLOCK_EVT_FEAT_PERIODIC,
-	.set_next_event	= ks8695_set_next_event,
-	.set_mode	= ks8695_set_mode,
+	.name			= "ks8695_t1tc",
+	/* Reasonably fast and accurate clock event */
+	.rating			= 300,
+	.features		= CLOCK_EVT_FEAT_ONESHOT |
+				  CLOCK_EVT_FEAT_PERIODIC,
+	.set_next_event		= ks8695_set_next_event,
+	.set_state_periodic	= ks8695_set_periodic,
 };
 
 /*

arch/arm/mach-lpc32xx/irq.c

@@ -283,25 +283,25 @@ static int lpc32xx_set_irq_type(struct irq_data *d, unsigned int type)
 	case IRQ_TYPE_EDGE_RISING:
 		/* Rising edge sensitive */
 		__lpc32xx_set_irq_type(d->hwirq, 1, 1);
-		__irq_set_handler_locked(d->irq, handle_edge_irq);
+		irq_set_handler_locked(d, handle_edge_irq);
 		break;
 
 	case IRQ_TYPE_EDGE_FALLING:
 		/* Falling edge sensitive */
 		__lpc32xx_set_irq_type(d->hwirq, 0, 1);
-		__irq_set_handler_locked(d->irq, handle_edge_irq);
+		irq_set_handler_locked(d, handle_edge_irq);
 		break;
 
 	case IRQ_TYPE_LEVEL_LOW:
 		/* Low level sensitive */
 		__lpc32xx_set_irq_type(d->hwirq, 0, 0);
-		__irq_set_handler_locked(d->irq, handle_level_irq);
+		irq_set_handler_locked(d, handle_level_irq);
 		break;
 
 	case IRQ_TYPE_LEVEL_HIGH:
 		/* High level sensitive */
 		__lpc32xx_set_irq_type(d->hwirq, 1, 0);
-		__irq_set_handler_locked(d->irq, handle_level_irq);
+		irq_set_handler_locked(d, handle_level_irq);
 		break;
 
 	/* Other modes are not supported */
@@ -434,7 +434,7 @@ void __init lpc32xx_init_irq(void)
 	for (i = 0; i < NR_IRQS; i++) {
 		irq_set_chip_and_handler(i, &lpc32xx_irq_chip,
 					 handle_level_irq);
-		set_irq_flags(i, IRQF_VALID);
+		irq_clear_status_flags(i, IRQ_NOREQUEST);
 	}
 
 	/* Set default mappings */

arch/arm/mach-lpc32xx/phy3250.c

@@ -212,7 +212,7 @@ static struct lpc32xx_mlc_platform_data lpc32xx_mlc_data = {
 	.dma_filter = pl08x_filter_id,
 };
 
-static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = {
+static const struct of_dev_auxdata const lpc32xx_auxdata_lookup[] __initconst = {
 	OF_DEV_AUXDATA("arm,pl022", 0x20084000, "dev:ssp0", NULL),
 	OF_DEV_AUXDATA("arm,pl022", 0x2008C000, "dev:ssp1", NULL),
 	OF_DEV_AUXDATA("arm,pl110", 0x31040000, "dev:clcd", &lpc32xx_clcd_data),
@@ -248,7 +248,7 @@ static void __init lpc3250_machine_init(void)
 			     lpc32xx_auxdata_lookup, NULL);
 }
 
-static char const *lpc32xx_dt_compat[] __initdata = {
+static const char *const lpc32xx_dt_compat[] __initconst = {
 	"nxp,lpc3220",
 	"nxp,lpc3230",
 	"nxp,lpc3240",

arch/arm/mach-lpc32xx/timer.c

@@ -43,36 +43,24 @@ static int lpc32xx_clkevt_next_event(unsigned long delta,
 	return 0;
 }
 
-static void lpc32xx_clkevt_mode(enum clock_event_mode mode,
-    struct clock_event_device *dev)
+static int lpc32xx_shutdown(struct clock_event_device *evt)
 {
-	switch (mode) {
-	case CLOCK_EVT_MODE_PERIODIC:
-		WARN_ON(1);
-		break;
-
-	case CLOCK_EVT_MODE_ONESHOT:
-	case CLOCK_EVT_MODE_SHUTDOWN:
-		/*
-		 * Disable the timer. When using oneshot, we must also
-		 * disable the timer to wait for the first call to
-		 * set_next_event().
-		 */
-		__raw_writel(0, LPC32XX_TIMER_TCR(LPC32XX_TIMER0_BASE));
-		break;
-
-	case CLOCK_EVT_MODE_UNUSED:
-	case CLOCK_EVT_MODE_RESUME:
-		break;
-	}
+	/*
+	 * Disable the timer. When using oneshot, we must also
+	 * disable the timer to wait for the first call to
+	 * set_next_event().
+	 */
+	__raw_writel(0, LPC32XX_TIMER_TCR(LPC32XX_TIMER0_BASE));
+	return 0;
 }
 
 static struct clock_event_device lpc32xx_clkevt = {
-	.name		= "lpc32xx_clkevt",
-	.features	= CLOCK_EVT_FEAT_ONESHOT,
-	.rating		= 300,
-	.set_next_event	= lpc32xx_clkevt_next_event,
-	.set_mode	= lpc32xx_clkevt_mode,
+	.name			= "lpc32xx_clkevt",
+	.features		= CLOCK_EVT_FEAT_ONESHOT,
+	.rating			= 300,
+	.set_next_event		= lpc32xx_clkevt_next_event,
+	.set_state_shutdown	= lpc32xx_shutdown,
+	.set_state_oneshot	= lpc32xx_shutdown,
 };
 
 static irqreturn_t lpc32xx_timer_interrupt(int irq, void *dev_id)

arch/arm/mach-mmp/mmp-dt.c

@@ -20,12 +20,12 @@
 
 extern void __init mmp_dt_init_timer(void);
 
-static const char *pxa168_dt_board_compat[] __initdata = {
+static const char *const pxa168_dt_board_compat[] __initconst = {
 	"mrvl,pxa168-aspenite",
 	NULL,
 };
 
-static const char *pxa910_dt_board_compat[] __initdata = {
+static const char *const pxa910_dt_board_compat[] __initconst = {
 	"mrvl,pxa910-dkb",
 	NULL,
 };

arch/arm/mach-mmp/mmp2-dt.c

@@ -30,7 +30,7 @@ static void __init mmp_init_time(void)
 	of_clk_init(NULL);
 }
 
-static const char *mmp2_dt_board_compat[] __initdata = {
+static const char *const mmp2_dt_board_compat[] __initconst = {
 	"mrvl,mmp2-brownstone",
 	NULL,
 };

arch/arm/mach-mmp/time.c

@@ -124,32 +124,25 @@ static int timer_set_next_event(unsigned long delta,
 	return 0;
 }
 
-static void timer_set_mode(enum clock_event_mode mode,
-			   struct clock_event_device *dev)
+static int timer_set_shutdown(struct clock_event_device *evt)
 {
 	unsigned long flags;
 
 	local_irq_save(flags);
-	switch (mode) {
-	case CLOCK_EVT_MODE_ONESHOT:
-	case CLOCK_EVT_MODE_UNUSED:
-	case CLOCK_EVT_MODE_SHUTDOWN:
-		/* disable the matching interrupt */
-		__raw_writel(0x00, mmp_timer_base + TMR_IER(0));
-		break;
-	case CLOCK_EVT_MODE_RESUME:
-	case CLOCK_EVT_MODE_PERIODIC:
-		break;
-	}
+	/* disable the matching interrupt */
+	__raw_writel(0x00, mmp_timer_base + TMR_IER(0));
 	local_irq_restore(flags);
+
+	return 0;
 }
 
 static struct clock_event_device ckevt = {
-	.name		= "clockevent",
-	.features	= CLOCK_EVT_FEAT_ONESHOT,
-	.rating		= 200,
-	.set_next_event	= timer_set_next_event,
-	.set_mode	= timer_set_mode,
+	.name			= "clockevent",
+	.features		= CLOCK_EVT_FEAT_ONESHOT,
+	.rating			= 200,
+	.set_next_event		= timer_set_next_event,
+	.set_state_shutdown	= timer_set_shutdown,
+	.set_state_oneshot	= timer_set_shutdown,
 };
 
 static cycle_t clksrc_read(struct clocksource *cs)

arch/arm/mach-mvebu/pmsu.c

@@ -415,7 +415,7 @@ static __init int armada_38x_cpuidle_init(void)
 	void __iomem *mpsoc_base;
 	u32 reg;
 
-	pr_warn("CPU idle is currently broken on Armada 38x: disabling");
+	pr_warn("CPU idle is currently broken on Armada 38x: disabling\n");
 	return 0;
 
 	np = of_find_compatible_node(NULL, NULL,
@@ -486,7 +486,7 @@ static int __init mvebu_v7_cpu_pm_init(void)
 	 */
 	if (of_machine_is_compatible("marvell,armada380")) {
 		cpu_hotplug_disable();
-		pr_warn("CPU hotplug support is currently broken on Armada 38x: disabling");
+		pr_warn("CPU hotplug support is currently broken on Armada 38x: disabling\n");
 	}
 
 	if (of_machine_is_compatible("marvell,armadaxp"))

arch/arm/mach-mxs/mach-mxs.c

@@ -282,7 +282,7 @@ static void __init apx4devkit_init(void)
 #define TX28_FEC_PHY_RESET	MXS_GPIO_NR(4, 13)
 #define TX28_FEC_nINT		MXS_GPIO_NR(4, 5)
 
-static const struct gpio tx28_gpios[] __initconst = {
+static const struct gpio const tx28_gpios[] __initconst = {
 	{ ENET0_MDC__GPIO_4_0, GPIOF_OUT_INIT_LOW, "GPIO_4_0" },
 	{ ENET0_MDIO__GPIO_4_1, GPIOF_OUT_INIT_LOW, "GPIO_4_1" },
 	{ ENET0_RX_EN__GPIO_4_2, GPIOF_OUT_INIT_LOW, "GPIO_4_2" },
@@ -528,7 +528,7 @@ static void mxs_restart(enum reboot_mode mode, const char *cmd)
 	soft_restart(0);
 }
 
-static const char *mxs_dt_compat[] __initdata = {
+static const char *const mxs_dt_compat[] __initconst = {
 	"fsl,imx28",
 	"fsl,imx23",
 	NULL,

arch/arm/mach-netx/generic.c

@@ -174,7 +174,7 @@ void __init netx_init_irq(void)
 	for (irq = NETX_IRQ_HIF_CHAINED(0); irq <= NETX_IRQ_HIF_LAST; irq++) {
 		irq_set_chip_and_handler(irq, &netx_hif_chip,
 					 handle_level_irq);
-		set_irq_flags(irq, IRQF_VALID);
+		irq_clear_status_flags(irq, IRQ_NOREQUEST);
 	}
 
 	writel(NETX_DPMAS_INT_EN_GLB_EN, NETX_DPMAS_INT_EN);

arch/arm/mach-netx/time.c

@@ -34,40 +34,40 @@
 #define TIMER_CLOCKEVENT 0
 #define TIMER_CLOCKSOURCE 1
 
-static void netx_set_mode(enum clock_event_mode mode,
-		struct clock_event_device *clk)
+static inline void timer_shutdown(struct clock_event_device *evt)
 {
-	u32 tmode;
-
 	/* disable timer */
 	writel(0, NETX_GPIO_COUNTER_CTRL(TIMER_CLOCKEVENT));
+}
+
+static int netx_shutdown(struct clock_event_device *evt)
+{
+	timer_shutdown(evt);
+
+	return 0;
+}
+
+static int netx_set_oneshot(struct clock_event_device *evt)
+{
+	u32 tmode = NETX_GPIO_COUNTER_CTRL_IRQ_EN | NETX_GPIO_COUNTER_CTRL_RUN;
+
+	timer_shutdown(evt);
+	writel(0, NETX_GPIO_COUNTER_MAX(TIMER_CLOCKEVENT));
+	writel(tmode, NETX_GPIO_COUNTER_CTRL(TIMER_CLOCKEVENT));
 
-	switch (mode) {
-	case CLOCK_EVT_MODE_PERIODIC:
-		writel(NETX_LATCH, NETX_GPIO_COUNTER_MAX(TIMER_CLOCKEVENT));
-		tmode = NETX_GPIO_COUNTER_CTRL_RST_EN |
-			NETX_GPIO_COUNTER_CTRL_IRQ_EN |
-			NETX_GPIO_COUNTER_CTRL_RUN;
-		break;
-
-	case CLOCK_EVT_MODE_ONESHOT:
-		writel(0, NETX_GPIO_COUNTER_MAX(TIMER_CLOCKEVENT));
-		tmode = NETX_GPIO_COUNTER_CTRL_IRQ_EN |
-			NETX_GPIO_COUNTER_CTRL_RUN;
-		break;
-
-	default:
-		WARN(1, "%s: unhandled mode %d\n", __func__, mode);
-		/* fall through */
-
-	case CLOCK_EVT_MODE_SHUTDOWN:
-	case CLOCK_EVT_MODE_UNUSED:
-	case CLOCK_EVT_MODE_RESUME:
-		tmode = 0;
-		break;
-	}
+	return 0;
+}
 
+static int netx_set_periodic(struct clock_event_device *evt)
+{
+	u32 tmode = NETX_GPIO_COUNTER_CTRL_RST_EN |
+		    NETX_GPIO_COUNTER_CTRL_IRQ_EN | NETX_GPIO_COUNTER_CTRL_RUN;
+
+	timer_shutdown(evt);
+	writel(NETX_LATCH, NETX_GPIO_COUNTER_MAX(TIMER_CLOCKEVENT));
 	writel(tmode, NETX_GPIO_COUNTER_CTRL(TIMER_CLOCKEVENT));
+
+	return 0;
 }
 
 static int netx_set_next_event(unsigned long evt,
@@ -81,7 +81,10 @@ static struct clock_event_device netx_clockevent = {
 	.name = "netx-timer" __stringify(TIMER_CLOCKEVENT),
 	.features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
 	.set_next_event = netx_set_next_event,
-	.set_mode = netx_set_mode,
+	.set_state_shutdown = netx_shutdown,
+	.set_state_periodic = netx_set_periodic,
+	.set_state_oneshot = netx_set_oneshot,
+	.tick_resume = netx_shutdown,
 };
 
 /*

arch/arm/mach-nomadik/cpu-8815.c

@@ -26,10 +26,8 @@
 #include <linux/irq.h>
 #include <linux/dma-mapping.h>
 #include <linux/of_irq.h>
-#include <linux/of_gpio.h>
 #include <linux/of_address.h>
 #include <linux/of_platform.h>
-#include <linux/gpio.h>
 
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
@@ -109,40 +107,6 @@ static void cpu8815_restart(enum reboot_mode mode, const char *cmd)
 	writel(1, srcbase + 0x18);
 }
 
-/*
- * This GPIO pin turns on a line that is used to detect card insertion
- * on this board.
- */
-static int __init cpu8815_mmcsd_init(void)
-{
-	struct device_node *cdbias;
-	int gpio, err;
-
-	cdbias = of_find_node_by_path("/usb-s8815/mmcsd-gpio");
-	if (!cdbias) {
-		pr_info("could not find MMC/SD card detect bias node\n");
-		return 0;
-	}
-	gpio = of_get_gpio(cdbias, 0);
-	if (gpio < 0) {
-		pr_info("could not obtain MMC/SD card detect bias GPIO\n");
-		return 0;
-	}
-	err = gpio_request(gpio, "card detect bias");
-	if (err) {
-		pr_info("failed to request card detect bias GPIO %d\n", gpio);
-		return -ENODEV;
-	}
-	err = gpio_direction_output(gpio, 0);
-	if (err){
-		pr_info("failed to set GPIO %d as output, low\n", gpio);
-		return err;
-	}
-	pr_info("enabled USB-S8815 CD bias GPIO %d, low\n", gpio);
-	return 0;
-}
-device_initcall(cpu8815_mmcsd_init);
-
 static const char * cpu8815_board_compat[] = {
 	"st,nomadik-nhk-15",
 	"calaosystems,usb-s8815",
@@ -150,9 +114,8 @@ static const char * cpu8815_board_compat[] = {
 };
 
 DT_MACHINE_START(NOMADIK_DT, "Nomadik STn8815")
-	/* At full speed latency must be >=2, so 0x249 in low bits */
-	.l2c_aux_val	= 0x00700249,
-	.l2c_aux_mask	= 0xfe0fefff,
+	.l2c_aux_val	= 0,
+	.l2c_aux_mask	= ~0,
 	.map_io		= cpu8815_map_io,
 	.restart	= cpu8815_restart,
 	.dt_compat      = cpu8815_board_compat,

arch/arm/mach-omap1/fpga.c

@@ -169,7 +169,7 @@ void omap1510_fpga_init_irq(void)
 		}
 
 		irq_set_handler(i, handle_edge_irq);
-		set_irq_flags(i, IRQF_VALID);
+		irq_clear_status_flags(i, IRQ_NOREQUEST);
 	}
 
 	/*

arch/arm/mach-omap1/irq.c

@@ -262,7 +262,7 @@ void __init omap1_init_irq(void)
 
 			irq_trigger = irq_banks[i].trigger_map >> IRQ_BIT(j);
 			omap_irq_set_cfg(j, 0, 0, irq_trigger);
-			set_irq_flags(j, IRQF_VALID);
+			irq_clear_status_flags(j, IRQ_NOREQUEST);
 		}
 		omap_alloc_gc(irq_banks[i].va, irq_base + i * 32, 32);
 	}

arch/arm/mach-omap1/time.c

@@ -124,29 +124,26 @@ static int omap_mpu_set_next_event(unsigned long cycles,
 	return 0;
 }
 
-static void omap_mpu_set_mode(enum clock_event_mode mode,
-			      struct clock_event_device *evt)
+static int omap_mpu_set_oneshot(struct clock_event_device *evt)
 {
-	switch (mode) {
-	case CLOCK_EVT_MODE_PERIODIC:
-		omap_mpu_set_autoreset(0);
-		break;
-	case CLOCK_EVT_MODE_ONESHOT:
-		omap_mpu_timer_stop(0);
-		omap_mpu_remove_autoreset(0);
-		break;
-	case CLOCK_EVT_MODE_UNUSED:
-	case CLOCK_EVT_MODE_SHUTDOWN:
-	case CLOCK_EVT_MODE_RESUME:
-		break;
-	}
+	omap_mpu_timer_stop(0);
+	omap_mpu_remove_autoreset(0);
+	return 0;
+}
+
+static int omap_mpu_set_periodic(struct clock_event_device *evt)
+{
+	omap_mpu_set_autoreset(0);
+	return 0;
 }
 
 static struct clock_event_device clockevent_mpu_timer1 = {
-	.name		= "mpu_timer1",
-	.features       = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
-	.set_next_event	= omap_mpu_set_next_event,
-	.set_mode	= omap_mpu_set_mode,
+	.name			= "mpu_timer1",
+	.features		= CLOCK_EVT_FEAT_PERIODIC |
+				  CLOCK_EVT_FEAT_ONESHOT,
+	.set_next_event		= omap_mpu_set_next_event,
+	.set_state_periodic	= omap_mpu_set_periodic,
+	.set_state_oneshot	= omap_mpu_set_oneshot,
 };
 
 static irqreturn_t omap_mpu_timer1_interrupt(int irq, void *dev_id)

arch/arm/mach-omap1/timer32k.c

@@ -114,29 +114,28 @@ static int omap_32k_timer_set_next_event(unsigned long delta,
 	return 0;
 }
 
-static void omap_32k_timer_set_mode(enum clock_event_mode mode,
-				    struct clock_event_device *evt)
+static int omap_32k_timer_shutdown(struct clock_event_device *evt)
 {
 	omap_32k_timer_stop();
+	return 0;
+}
 
-	switch (mode) {
-	case CLOCK_EVT_MODE_PERIODIC:
-		omap_32k_timer_start(OMAP_32K_TIMER_TICK_PERIOD);
-		break;
-	case CLOCK_EVT_MODE_ONESHOT:
-	case CLOCK_EVT_MODE_UNUSED:
-	case CLOCK_EVT_MODE_SHUTDOWN:
-		break;
-	case CLOCK_EVT_MODE_RESUME:
-		break;
-	}
+static int omap_32k_timer_set_periodic(struct clock_event_device *evt)
+{
+	omap_32k_timer_stop();
+	omap_32k_timer_start(OMAP_32K_TIMER_TICK_PERIOD);
+	return 0;
 }
 
 static struct clock_event_device clockevent_32k_timer = {
-	.name		= "32k-timer",
-	.features       = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
-	.set_next_event	= omap_32k_timer_set_next_event,
-	.set_mode	= omap_32k_timer_set_mode,
+	.name			= "32k-timer",
+	.features		= CLOCK_EVT_FEAT_PERIODIC |
+				  CLOCK_EVT_FEAT_ONESHOT,
+	.set_next_event		= omap_32k_timer_set_next_event,
+	.set_state_shutdown	= omap_32k_timer_shutdown,
+	.set_state_periodic	= omap_32k_timer_set_periodic,
+	.set_state_oneshot	= omap_32k_timer_shutdown,
+	.tick_resume		= omap_32k_timer_shutdown,
 };
 
 static irqreturn_t omap_32k_timer_interrupt(int irq, void *dev_id)

arch/arm/mach-omap2/Kconfig

@@ -178,26 +178,6 @@ config MACH_OMAP_LDP
 	default y
 	select OMAP_PACKAGE_CBB
 
-config MACH_OMAP3530_LV_SOM
-	bool "OMAP3 Logic 3530 LV SOM board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-	help
-	 Support for the LogicPD OMAP3530 SOM Development kit
-	 for full description please see the products webpage at
-	 http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap35x-development-kit
-
-config MACH_OMAP3_TORPEDO
-	bool "OMAP3 Logic 35x Torpedo board"
-	depends on ARCH_OMAP3
-	default y
-	select OMAP_PACKAGE_CBB
-	help
-	 Support for the LogicPD OMAP35x Torpedo Development kit
-	 for full description please see the products webpage at
-	 http://www.logicpd.com/products/development-kits/zoom-omap35x-torpedo-development-kit
-
 config MACH_OMAP3517EVM
 	bool "OMAP3517/ AM3517 EVM board"
 	depends on ARCH_OMAP3

arch/arm/mach-omap2/Makefile

@@ -235,9 +235,6 @@ obj-$(CONFIG_SOC_OMAP2420)		+= msdi.o
 # Specific board support
 obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o pdata-quirks.o
 obj-$(CONFIG_MACH_OMAP_LDP)		+= board-ldp.o
-obj-$(CONFIG_MACH_OMAP3530_LV_SOM)      += board-omap3logic.o
-obj-$(CONFIG_MACH_OMAP3_TORPEDO)        += board-omap3logic.o
-obj-$(CONFIG_MACH_OMAP3_PANDORA)	+= board-omap3pandora.o
 obj-$(CONFIG_MACH_NOKIA_N8X0)		+= board-n8x0.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51.o sdram-nokia.o
 obj-$(CONFIG_MACH_NOKIA_RX51)		+= board-rx51-peripherals.o

arch/arm/mach-omap2/board-omap3logic.c

@@ -1,249 +0,0 @@
-/*
- * linux/arch/arm/mach-omap2/board-omap3logic.c
- *
- * Copyright (C) 2010 Li-Pro.Net
- * Stephan Linz <linz@li-pro.net>
- *
- * Copyright (C) 2010-2012 Logic Product Development, Inc.
- * Peter Barada <peter.barada@logicpd.com>
- * Ashwin BIhari <ashwin.bihari@logicpd.com>
- *
- * Modified from Beagle, EVM, and RX51
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/delay.h>
-#include <linux/err.h>
-#include <linux/clk.h>
-#include <linux/io.h>
-#include <linux/gpio.h>
-
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-
-#include <linux/i2c/twl.h>
-#include <linux/mmc/host.h>
-#include <linux/usb/phy.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include "mux.h"
-#include "hsmmc.h"
-#include "control.h"
-#include "common-board-devices.h"
-#include "gpmc.h"
-#include "gpmc-smsc911x.h"
-
-#define OMAP3LOGIC_SMSC911X_CS			1
-
-#define OMAP3530_LV_SOM_MMC_GPIO_CD		110
-#define OMAP3530_LV_SOM_MMC_GPIO_WP		126
-#define OMAP3530_LV_SOM_SMSC911X_GPIO_IRQ	152
-
-#define OMAP3_TORPEDO_MMC_GPIO_CD		127
-#define OMAP3_TORPEDO_SMSC911X_GPIO_IRQ		129
-
-static struct regulator_consumer_supply omap3logic_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data omap3logic_vmmc1 = {
-	.constraints = {
-		.name			= "VMMC1",
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies  = ARRAY_SIZE(omap3logic_vmmc1_supply),
-	.consumer_supplies      = omap3logic_vmmc1_supply,
-};
-
-static struct twl4030_gpio_platform_data omap3logic_gpio_data = {
-	.use_leds	= true,
-	.pullups	= BIT(1),
-	.pulldowns	= BIT(2)  | BIT(6)  | BIT(7)  | BIT(8)
-			| BIT(13) | BIT(15) | BIT(16) | BIT(17),
-};
-
-static struct twl4030_usb_data omap3logic_usb_data = {
-	.usb_mode	= T2_USB_MODE_ULPI,
-};
-
-
-static struct twl4030_platform_data omap3logic_twldata = {
-	/* platform_data for children goes here */
-	.gpio		= &omap3logic_gpio_data,
-	.vmmc1		= &omap3logic_vmmc1,
-	.usb		= &omap3logic_usb_data,
-};
-
-static int __init omap3logic_i2c_init(void)
-{
-	omap3_pmic_init("twl4030", &omap3logic_twldata);
-	return 0;
-}
-
-static struct omap2_hsmmc_info __initdata board_mmc_info[] = {
-	{
-		.name		= "external",
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= -EINVAL,
-	},
-	{}      /* Terminator */
-};
-
-static void __init board_mmc_init(void)
-{
-	if (machine_is_omap3530_lv_som()) {
-		/* OMAP3530 LV SOM board */
-		board_mmc_info[0].gpio_cd = OMAP3530_LV_SOM_MMC_GPIO_CD;
-		board_mmc_info[0].gpio_wp = OMAP3530_LV_SOM_MMC_GPIO_WP;
-		omap_mux_init_signal("gpio_110", OMAP_PIN_OUTPUT);
-		omap_mux_init_signal("gpio_126", OMAP_PIN_OUTPUT);
-	} else if (machine_is_omap3_torpedo()) {
-		/* OMAP3 Torpedo board */
-		board_mmc_info[0].gpio_cd = OMAP3_TORPEDO_MMC_GPIO_CD;
-		omap_mux_init_signal("gpio_127", OMAP_PIN_OUTPUT);
-	} else {
-		/* unsupported board */
-		printk(KERN_ERR "%s(): unknown machine type\n", __func__);
-		return;
-	}
-
-	omap_hsmmc_init(board_mmc_info);
-}
-
-static struct omap_smsc911x_platform_data __initdata board_smsc911x_data = {
-	.cs             = OMAP3LOGIC_SMSC911X_CS,
-	.gpio_irq       = -EINVAL,
-	.gpio_reset     = -EINVAL,
-};
-
-/* TODO/FIXME (comment by Peter Barada, LogicPD):
- * Fix the PBIAS voltage for Torpedo MMC1 pins that
- * are used for other needs (IRQs, etc).            */
-static void omap3torpedo_fix_pbias_voltage(void)
-{
-	u16 control_pbias_offset = OMAP343X_CONTROL_PBIAS_LITE;
-	u32 reg;
-
-	if (machine_is_omap3_torpedo())
-	{
-		/* Set the bias for the pin */
-		reg = omap_ctrl_readl(control_pbias_offset);
-
-		reg &= ~OMAP343X_PBIASLITEPWRDNZ1;
-		omap_ctrl_writel(reg, control_pbias_offset);
-
-		/* 100ms delay required for PBIAS configuration */
-		msleep(100);
-
-		reg |= OMAP343X_PBIASLITEVMODE1;
-		reg |= OMAP343X_PBIASLITEPWRDNZ1;
-		omap_ctrl_writel(reg | 0x300, control_pbias_offset);
-	}
-}
-
-static inline void __init board_smsc911x_init(void)
-{
-	if (machine_is_omap3530_lv_som()) {
-		/* OMAP3530 LV SOM board */
-		board_smsc911x_data.gpio_irq =
-					OMAP3530_LV_SOM_SMSC911X_GPIO_IRQ;
-		omap_mux_init_signal("gpio_152", OMAP_PIN_INPUT);
-	} else if (machine_is_omap3_torpedo()) {
-		/* OMAP3 Torpedo board */
-		board_smsc911x_data.gpio_irq = OMAP3_TORPEDO_SMSC911X_GPIO_IRQ;
-		omap_mux_init_signal("gpio_129", OMAP_PIN_INPUT);
-	} else {
-		/* unsupported board */
-		printk(KERN_ERR "%s(): unknown machine type\n", __func__);
-		return;
-	}
-
-	gpmc_smsc911x_init(&board_smsc911x_data);
-}
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	/* mUSB */
-	OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
-	OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-	OMAP3_MUX(HSUSB0_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
-
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static struct regulator_consumer_supply dummy_supplies[] = {
-	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
-	REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
-};
-
-static void __init omap3logic_init(void)
-{
-	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-	omap3torpedo_fix_pbias_voltage();
-	omap3logic_i2c_init();
-	omap_serial_init();
-	omap_sdrc_init(NULL, NULL);
-	board_mmc_init();
-	board_smsc911x_init();
-
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-
-	/* Ensure SDRC pins are mux'd for self-refresh */
-	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(OMAP3_TORPEDO, "Logic OMAP3 Torpedo board")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap35xx_init_early,
-	.init_irq	= omap3_init_irq,
-	.init_machine	= omap3logic_init,
-	.init_late	= omap35xx_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END
-
-MACHINE_START(OMAP3530_LV_SOM, "OMAP Logic 3530 LV SOM board")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap35xx_init_early,
-	.init_irq	= omap3_init_irq,
-	.init_machine	= omap3logic_init,
-	.init_late	= omap35xx_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END

arch/arm/mach-omap2/board-omap3pandora.c

@@ -1,633 +0,0 @@
-/*
- * board-omap3pandora.c (Pandora Handheld Console)
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
- * 02110-1301 USA
- *
- */
-
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-
-#include <linux/spi/spi.h>
-#include <linux/regulator/machine.h>
-#include <linux/i2c/twl.h>
-#include <linux/omap-gpmc.h>
-#include <linux/wl12xx.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/nand.h>
-#include <linux/leds.h>
-#include <linux/input.h>
-#include <linux/input/matrix_keypad.h>
-#include <linux/gpio.h>
-#include <linux/gpio_keys.h>
-#include <linux/mmc/host.h>
-#include <linux/mmc/card.h>
-#include <linux/regulator/fixed.h>
-#include <linux/usb/phy.h>
-#include <linux/platform_data/spi-omap2-mcspi.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-
-#include "common.h"
-#include <video/omapdss.h>
-#include <video/omap-panel-data.h>
-#include <linux/platform_data/mtd-nand-omap2.h>
-
-#include "mux.h"
-#include "sdram-micron-mt46h32m32lf-6.h"
-#include "hsmmc.h"
-#include "common-board-devices.h"
-
-#define PANDORA_WIFI_IRQ_GPIO		21
-#define PANDORA_WIFI_NRESET_GPIO	23
-#define OMAP3_PANDORA_TS_GPIO		94
-
-static struct mtd_partition omap3pandora_nand_partitions[] = {
-	{
-		.name           = "xloader",
-		.offset         = 0,
-		.size           = 4 * NAND_BLOCK_SIZE,
-		.mask_flags     = MTD_WRITEABLE
-	}, {
-		.name           = "uboot",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = 15 * NAND_BLOCK_SIZE,
-	}, {
-		.name           = "uboot-env",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = 1 * NAND_BLOCK_SIZE,
-	}, {
-		.name           = "boot",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = 80 * NAND_BLOCK_SIZE,
-	}, {
-		.name           = "rootfs",
-		.offset         = MTDPART_OFS_APPEND,
-		.size           = MTDPART_SIZ_FULL,
-	},
-};
-
-static struct omap_nand_platform_data pandora_nand_data = {
-	.cs		= 0,
-	.devsize	= NAND_BUSWIDTH_16,
-	.xfer_type	= NAND_OMAP_PREFETCH_DMA,
-	.parts		= omap3pandora_nand_partitions,
-	.nr_parts	= ARRAY_SIZE(omap3pandora_nand_partitions),
-};
-
-static struct gpio_led pandora_gpio_leds[] = {
-	{
-		.name			= "pandora::sd1",
-		.default_trigger	= "mmc0",
-		.gpio			= 128,
-	}, {
-		.name			= "pandora::sd2",
-		.default_trigger	= "mmc1",
-		.gpio			= 129,
-	}, {
-		.name			= "pandora::bluetooth",
-		.gpio			= 158,
-	}, {
-		.name			= "pandora::wifi",
-		.gpio			= 159,
-	},
-};
-
-static struct gpio_led_platform_data pandora_gpio_led_data = {
-	.leds		= pandora_gpio_leds,
-	.num_leds	= ARRAY_SIZE(pandora_gpio_leds),
-};
-
-static struct platform_device pandora_leds_gpio = {
-	.name	= "leds-gpio",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &pandora_gpio_led_data,
-	},
-};
-
-static struct platform_device pandora_backlight = {
-	.name	= "pandora-backlight",
-	.id	= -1,
-};
-
-#define GPIO_BUTTON(gpio_num, ev_type, ev_code, act_low, descr)	\
-{								\
-	.gpio		= gpio_num,				\
-	.type		= ev_type,				\
-	.code		= ev_code,				\
-	.active_low	= act_low,				\
-	.debounce_interval = 4,					\
-	.desc		= "btn " descr,				\
-}
-
-#define GPIO_BUTTON_LOW(gpio_num, event_code, description)	\
-	GPIO_BUTTON(gpio_num, EV_KEY, event_code, 1, description)
-
-static struct gpio_keys_button pandora_gpio_keys[] = {
-	GPIO_BUTTON_LOW(110,	KEY_UP,		"up"),
-	GPIO_BUTTON_LOW(103,	KEY_DOWN,	"down"),
-	GPIO_BUTTON_LOW(96,	KEY_LEFT,	"left"),
-	GPIO_BUTTON_LOW(98,	KEY_RIGHT,	"right"),
-	GPIO_BUTTON_LOW(109,	KEY_PAGEUP,	"game 1"),
-	GPIO_BUTTON_LOW(111,	KEY_END,	"game 2"),
-	GPIO_BUTTON_LOW(106,	KEY_PAGEDOWN,	"game 3"),
-	GPIO_BUTTON_LOW(101,	KEY_HOME,	"game 4"),
-	GPIO_BUTTON_LOW(102,	KEY_RIGHTSHIFT,	"l"),
-	GPIO_BUTTON_LOW(97,	KEY_KPPLUS,	"l2"),
-	GPIO_BUTTON_LOW(105,	KEY_RIGHTCTRL,	"r"),
-	GPIO_BUTTON_LOW(107,	KEY_KPMINUS,	"r2"),
-	GPIO_BUTTON_LOW(104,	KEY_LEFTCTRL,	"ctrl"),
-	GPIO_BUTTON_LOW(99,	KEY_MENU,	"menu"),
-	GPIO_BUTTON_LOW(176,	KEY_COFFEE,	"hold"),
-	GPIO_BUTTON(100, EV_KEY, KEY_LEFTALT, 0, "alt"),
-	GPIO_BUTTON(108, EV_SW, SW_LID, 1, "lid"),
-};
-
-static struct gpio_keys_platform_data pandora_gpio_key_info = {
-	.buttons	= pandora_gpio_keys,
-	.nbuttons	= ARRAY_SIZE(pandora_gpio_keys),
-};
-
-static struct platform_device pandora_keys_gpio = {
-	.name	= "gpio-keys",
-	.id	= -1,
-	.dev	= {
-		.platform_data	= &pandora_gpio_key_info,
-	},
-};
-
-static const uint32_t board_keymap[] = {
-	/* row, col, code */
-	KEY(0, 0, KEY_9),
-	KEY(0, 1, KEY_8),
-	KEY(0, 2, KEY_I),
-	KEY(0, 3, KEY_J),
-	KEY(0, 4, KEY_N),
-	KEY(0, 5, KEY_M),
-	KEY(1, 0, KEY_0),
-	KEY(1, 1, KEY_7),
-	KEY(1, 2, KEY_U),
-	KEY(1, 3, KEY_H),
-	KEY(1, 4, KEY_B),
-	KEY(1, 5, KEY_SPACE),
-	KEY(2, 0, KEY_BACKSPACE),
-	KEY(2, 1, KEY_6),
-	KEY(2, 2, KEY_Y),
-	KEY(2, 3, KEY_G),
-	KEY(2, 4, KEY_V),
-	KEY(2, 5, KEY_FN),
-	KEY(3, 0, KEY_O),
-	KEY(3, 1, KEY_5),
-	KEY(3, 2, KEY_T),
-	KEY(3, 3, KEY_F),
-	KEY(3, 4, KEY_C),
-	KEY(4, 0, KEY_P),
-	KEY(4, 1, KEY_4),
-	KEY(4, 2, KEY_R),
-	KEY(4, 3, KEY_D),
-	KEY(4, 4, KEY_X),
-	KEY(5, 0, KEY_K),
-	KEY(5, 1, KEY_3),
-	KEY(5, 2, KEY_E),
-	KEY(5, 3, KEY_S),
-	KEY(5, 4, KEY_Z),
-	KEY(6, 0, KEY_L),
-	KEY(6, 1, KEY_2),
-	KEY(6, 2, KEY_W),
-	KEY(6, 3, KEY_A),
-	KEY(6, 4, KEY_DOT),
-	KEY(7, 0, KEY_ENTER),
-	KEY(7, 1, KEY_1),
-	KEY(7, 2, KEY_Q),
-	KEY(7, 3, KEY_LEFTSHIFT),
-	KEY(7, 4, KEY_COMMA),
-};
-
-static struct matrix_keymap_data board_map_data = {
-	.keymap			= board_keymap,
-	.keymap_size		= ARRAY_SIZE(board_keymap),
-};
-
-static struct twl4030_keypad_data pandora_kp_data = {
-	.keymap_data	= &board_map_data,
-	.rows		= 8,
-	.cols		= 6,
-	.rep		= 1,
-};
-
-static struct connector_atv_platform_data pandora_tv_pdata = {
-	.name = "tv",
-	.source = "venc.0",
-	.connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
-	.invert_polarity = false,
-};
-
-static struct platform_device pandora_tv_connector_device = {
-	.name                   = "connector-analog-tv",
-	.id                     = 0,
-	.dev.platform_data      = &pandora_tv_pdata,
-};
-
-static struct omap_dss_board_info pandora_dss_data = {
-	.default_display_name = "lcd",
-};
-
-static void pandora_wl1251_init_card(struct mmc_card *card)
-{
-	/*
-	 * We have TI wl1251 attached to MMC3. Pass this information to
-	 * SDIO core because it can't be probed by normal methods.
-	 */
-	if (card->type == MMC_TYPE_SDIO || card->type == MMC_TYPE_SD_COMBO) {
-		card->quirks |= MMC_QUIRK_NONSTD_SDIO;
-		card->cccr.wide_bus = 1;
-		card->cis.vendor = 0x104c;
-		card->cis.device = 0x9066;
-		card->cis.blksize = 512;
-		card->cis.max_dtr = 20000000;
-	}
-}
-
-static struct omap2_hsmmc_info omap3pandora_mmc[] = {
-	{
-		.mmc		= 1,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= 126,
-		.ext_clock	= 0,
-		.deferred	= true,
-	},
-	{
-		.mmc		= 2,
-		.caps		= MMC_CAP_4_BIT_DATA,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= 127,
-		.ext_clock	= 1,
-		.transceiver	= true,
-		.deferred	= true,
-	},
-	{
-		.mmc		= 3,
-		.caps		= MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD,
-		.gpio_cd	= -EINVAL,
-		.gpio_wp	= -EINVAL,
-		.init_card	= pandora_wl1251_init_card,
-	},
-	{}	/* Terminator */
-};
-
-static int omap3pandora_twl_gpio_setup(struct device *dev,
-		unsigned gpio, unsigned ngpio)
-{
-	int ret, gpio_32khz;
-
-	/* gpio + {0,1} is "mmc{0,1}_cd" (input/IRQ) */
-	omap3pandora_mmc[0].gpio_cd = gpio + 0;
-	omap3pandora_mmc[1].gpio_cd = gpio + 1;
-	omap_hsmmc_late_init(omap3pandora_mmc);
-
-	/* gpio + 13 drives 32kHz buffer for wifi module */
-	gpio_32khz = gpio + 13;
-	ret = gpio_request_one(gpio_32khz, GPIOF_OUT_INIT_HIGH, "wifi 32kHz");
-	if (ret < 0) {
-		pr_err("Cannot get GPIO line %d, ret=%d\n", gpio_32khz, ret);
-		return -ENODEV;
-	}
-
-	return 0;
-}
-
-static struct twl4030_gpio_platform_data omap3pandora_gpio_data = {
-	.setup		= omap3pandora_twl_gpio_setup,
-};
-
-static struct regulator_consumer_supply pandora_vmmc1_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-static struct regulator_consumer_supply pandora_vmmc2_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1")
-};
-
-static struct regulator_consumer_supply pandora_vmmc3_supply[] = {
-	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.2"),
-};
-
-static struct regulator_consumer_supply pandora_vdds_supplies[] = {
-	REGULATOR_SUPPLY("vdds_sdi", "omapdss"),
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss_dpi.0"),
-	REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.0"),
-};
-
-static struct regulator_consumer_supply pandora_vcc_lcd_supply[] = {
-	REGULATOR_SUPPLY("vcc", "spi1.1"),
-};
-
-static struct regulator_consumer_supply pandora_usb_phy_supply[] = {
-	REGULATOR_SUPPLY("vcc", "usb_phy_gen_xceiv.2"),	/* hsusb port 2 */
-};
-
-/* ads7846 on SPI and 2 nub controllers on I2C */
-static struct regulator_consumer_supply pandora_vaux4_supplies[] = {
-	REGULATOR_SUPPLY("vcc", "spi1.0"),
-	REGULATOR_SUPPLY("vcc", "3-0066"),
-	REGULATOR_SUPPLY("vcc", "3-0067"),
-};
-
-static struct regulator_consumer_supply pandora_adac_supply[] = {
-	REGULATOR_SUPPLY("vcc", "soc-audio"),
-};
-
-/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
-static struct regulator_init_data pandora_vmmc1 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(pandora_vmmc1_supply),
-	.consumer_supplies	= pandora_vmmc1_supply,
-};
-
-/* VMMC2 for MMC2 pins CMD, CLK, DAT0..DAT3 (max 100 mA) */
-static struct regulator_init_data pandora_vmmc2 = {
-	.constraints = {
-		.min_uV			= 1850000,
-		.max_uV			= 3150000,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
-					| REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(pandora_vmmc2_supply),
-	.consumer_supplies	= pandora_vmmc2_supply,
-};
-
-/* VAUX1 for LCD */
-static struct regulator_init_data pandora_vaux1 = {
-	.constraints = {
-		.min_uV			= 3000000,
-		.max_uV			= 3000000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(pandora_vcc_lcd_supply),
-	.consumer_supplies	= pandora_vcc_lcd_supply,
-};
-
-/* VAUX2 for USB host PHY */
-static struct regulator_init_data pandora_vaux2 = {
-	.constraints = {
-		.min_uV			= 1800000,
-		.max_uV			= 1800000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(pandora_usb_phy_supply),
-	.consumer_supplies	= pandora_usb_phy_supply,
-};
-
-/* VAUX4 for ads7846 and nubs */
-static struct regulator_init_data pandora_vaux4 = {
-	.constraints = {
-		.min_uV			= 2800000,
-		.max_uV			= 2800000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(pandora_vaux4_supplies),
-	.consumer_supplies	= pandora_vaux4_supplies,
-};
-
-/* VSIM for audio DAC */
-static struct regulator_init_data pandora_vsim = {
-	.constraints = {
-		.min_uV			= 2800000,
-		.max_uV			= 2800000,
-		.apply_uV		= true,
-		.valid_modes_mask	= REGULATOR_MODE_NORMAL
-					| REGULATOR_MODE_STANDBY,
-		.valid_ops_mask		= REGULATOR_CHANGE_MODE
-					| REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(pandora_adac_supply),
-	.consumer_supplies	= pandora_adac_supply,
-};
-
-/* Fixed regulator internal to Wifi module */
-static struct regulator_init_data pandora_vmmc3 = {
-	.constraints = {
-		.valid_ops_mask		= REGULATOR_CHANGE_STATUS,
-	},
-	.num_consumer_supplies	= ARRAY_SIZE(pandora_vmmc3_supply),
-	.consumer_supplies	= pandora_vmmc3_supply,
-};
-
-static struct fixed_voltage_config pandora_vwlan = {
-	.supply_name		= "vwlan",
-	.microvolts		= 1800000, /* 1.8V */
-	.gpio			= PANDORA_WIFI_NRESET_GPIO,
-	.startup_delay		= 50000, /* 50ms */
-	.enable_high		= 1,
-	.enabled_at_boot	= 0,
-	.init_data		= &pandora_vmmc3,
-};
-
-static struct platform_device pandora_vwlan_device = {
-	.name		= "reg-fixed-voltage",
-	.id		= 1,
-	.dev = {
-		.platform_data = &pandora_vwlan,
-	},
-};
-
-static struct twl4030_bci_platform_data pandora_bci_data;
-
-static struct twl4030_power_data pandora_power_data = {
-	.use_poweroff	= true,
-};
-
-static struct twl4030_platform_data omap3pandora_twldata = {
-	.gpio		= &omap3pandora_gpio_data,
-	.vmmc1		= &pandora_vmmc1,
-	.vmmc2		= &pandora_vmmc2,
-	.vaux1		= &pandora_vaux1,
-	.vaux2		= &pandora_vaux2,
-	.vaux4		= &pandora_vaux4,
-	.vsim		= &pandora_vsim,
-	.keypad		= &pandora_kp_data,
-	.bci		= &pandora_bci_data,
-	.power		= &pandora_power_data,
-};
-
-static struct i2c_board_info __initdata omap3pandora_i2c3_boardinfo[] = {
-	{
-		I2C_BOARD_INFO("bq27500", 0x55),
-		.flags = I2C_CLIENT_WAKE,
-	},
-};
-
-static int __init omap3pandora_i2c_init(void)
-{
-	omap3_pmic_get_config(&omap3pandora_twldata,
-			TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO,
-			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
-
-	omap3pandora_twldata.vdac->constraints.apply_uV = true;
-
-	omap3pandora_twldata.vpll2->constraints.apply_uV = true;
-	omap3pandora_twldata.vpll2->num_consumer_supplies =
-					ARRAY_SIZE(pandora_vdds_supplies);
-	omap3pandora_twldata.vpll2->consumer_supplies = pandora_vdds_supplies;
-
-	omap3_pmic_init("tps65950", &omap3pandora_twldata);
-	/* i2c2 pins are not connected */
-	omap_register_i2c_bus(3, 100, omap3pandora_i2c3_boardinfo,
-			ARRAY_SIZE(omap3pandora_i2c3_boardinfo));
-	return 0;
-}
-
-static struct panel_tpo_td043mtea1_platform_data pandora_lcd_pdata = {
-	.name                   = "lcd",
-	.source                 = "dpi.0",
-
-	.data_lines		= 24,
-	.nreset_gpio		= 157,
-};
-
-static struct spi_board_info omap3pandora_spi_board_info[] __initdata = {
-	{
-		.modalias		= "panel-tpo-td043mtea1",
-		.bus_num		= 1,
-		.chip_select		= 1,
-		.max_speed_hz		= 375000,
-		.platform_data		= &pandora_lcd_pdata,
-	}
-};
-
-static void __init pandora_wl1251_init(void)
-{
-	struct wl1251_platform_data pandora_wl1251_pdata;
-	int ret;
-
-	memset(&pandora_wl1251_pdata, 0, sizeof(pandora_wl1251_pdata));
-
-	pandora_wl1251_pdata.power_gpio = -1;
-
-	ret = gpio_request_one(PANDORA_WIFI_IRQ_GPIO, GPIOF_IN, "wl1251 irq");
-	if (ret < 0)
-		goto fail;
-
-	pandora_wl1251_pdata.irq = gpio_to_irq(PANDORA_WIFI_IRQ_GPIO);
-	if (pandora_wl1251_pdata.irq < 0)
-		goto fail_irq;
-
-	pandora_wl1251_pdata.use_eeprom = true;
-	ret = wl1251_set_platform_data(&pandora_wl1251_pdata);
-	if (ret < 0)
-		goto fail_irq;
-
-	return;
-
-fail_irq:
-	gpio_free(PANDORA_WIFI_IRQ_GPIO);
-fail:
-	printk(KERN_ERR "wl1251 board initialisation failed\n");
-}
-
-static struct usbhs_phy_data phy_data[] __initdata = {
-	{
-		.port = 2,
-		.reset_gpio = 16,
-		.vcc_gpio = -EINVAL,
-	},
-};
-
-static struct platform_device *omap3pandora_devices[] __initdata = {
-	&pandora_leds_gpio,
-	&pandora_keys_gpio,
-	&pandora_vwlan_device,
-	&pandora_backlight,
-	&pandora_tv_connector_device,
-};
-
-static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
-	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
-};
-
-#ifdef CONFIG_OMAP_MUX
-static struct omap_board_mux board_mux[] __initdata = {
-	{ .reg_offset = OMAP_MUX_TERMINATOR },
-};
-#endif
-
-static void __init omap3pandora_init(void)
-{
-	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
-	omap_hsmmc_init(omap3pandora_mmc);
-	omap3pandora_i2c_init();
-	pandora_wl1251_init();
-	platform_add_devices(omap3pandora_devices,
-			ARRAY_SIZE(omap3pandora_devices));
-	omap_display_init(&pandora_dss_data);
-	omap_serial_init();
-	omap_sdrc_init(mt46h32m32lf6_sdrc_params,
-				  mt46h32m32lf6_sdrc_params);
-	spi_register_board_info(omap3pandora_spi_board_info,
-			ARRAY_SIZE(omap3pandora_spi_board_info));
-	omap_ads7846_init(1, OMAP3_PANDORA_TS_GPIO, 0, NULL);
-
-	usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
-	usbhs_init(&usbhs_bdata);
-
-	usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
-	usb_musb_init(NULL);
-	gpmc_nand_init(&pandora_nand_data, NULL);
-
-	/* Ensure SDRC pins are mux'd for self-refresh */
-	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
-	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
-}
-
-MACHINE_START(OMAP3_PANDORA, "Pandora Handheld Console")
-	.atag_offset	= 0x100,
-	.reserve	= omap_reserve,
-	.map_io		= omap3_map_io,
-	.init_early	= omap35xx_init_early,
-	.init_irq	= omap3_init_irq,
-	.init_machine	= omap3pandora_init,
-	.init_late	= omap35xx_init_late,
-	.init_time	= omap3_sync32k_timer_init,
-	.restart	= omap3xxx_restart,
-MACHINE_END

arch/arm/mach-omap2/prm_common.c

@@ -705,7 +705,7 @@ static struct omap_prcm_init_data scrm_data __initdata = {
 };
 #endif
 
-static const struct of_device_id omap_prcm_dt_match_table[] __initconst = {
+static const struct of_device_id const omap_prcm_dt_match_table[] __initconst = {
 #ifdef CONFIG_SOC_AM33XX
 	{ .compatible = "ti,am3-prcm", .data = &am3_prm_data },
 #endif

arch/arm/mach-omap2/timer.c

@@ -102,38 +102,38 @@ static int omap2_gp_timer_set_next_event(unsigned long cycles,
 	return 0;
 }
 
-static void omap2_gp_timer_set_mode(enum clock_event_mode mode,
-				    struct clock_event_device *evt)
+static int omap2_gp_timer_shutdown(struct clock_event_device *evt)
+{
+	__omap_dm_timer_stop(&clkev, OMAP_TIMER_POSTED, clkev.rate);
+	return 0;
+}
+
+static int omap2_gp_timer_set_periodic(struct clock_event_device *evt)
 {
 	u32 period;
 
 	__omap_dm_timer_stop(&clkev, OMAP_TIMER_POSTED, clkev.rate);
 
-	switch (mode) {
-	case CLOCK_EVT_MODE_PERIODIC:
-		period = clkev.rate / HZ;
-		period -= 1;
-		/* Looks like we need to first set the load value separately */
-		__omap_dm_timer_write(&clkev, OMAP_TIMER_LOAD_REG,
-				      0xffffffff - period, OMAP_TIMER_POSTED);
-		__omap_dm_timer_load_start(&clkev,
-					OMAP_TIMER_CTRL_AR | OMAP_TIMER_CTRL_ST,
-					0xffffffff - period, OMAP_TIMER_POSTED);
-		break;
-	case CLOCK_EVT_MODE_ONESHOT:
-		break;
-	case CLOCK_EVT_MODE_UNUSED:
-	case CLOCK_EVT_MODE_SHUTDOWN:
-	case CLOCK_EVT_MODE_RESUME:
-		break;
-	}
+	period = clkev.rate / HZ;
+	period -= 1;
+	/* Looks like we need to first set the load value separately */
+	__omap_dm_timer_write(&clkev, OMAP_TIMER_LOAD_REG, 0xffffffff - period,
+			      OMAP_TIMER_POSTED);
+	__omap_dm_timer_load_start(&clkev,
+				   OMAP_TIMER_CTRL_AR | OMAP_TIMER_CTRL_ST,
+				   0xffffffff - period, OMAP_TIMER_POSTED);
+	return 0;
 }
 
 static struct clock_event_device clockevent_gpt = {
-	.features       = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
-	.rating		= 300,
-	.set_next_event	= omap2_gp_timer_set_next_event,
-	.set_mode	= omap2_gp_timer_set_mode,
+	.features		= CLOCK_EVT_FEAT_PERIODIC |
+				  CLOCK_EVT_FEAT_ONESHOT,
+	.rating			= 300,
+	.set_next_event		= omap2_gp_timer_set_next_event,
+	.set_state_shutdown	= omap2_gp_timer_shutdown,
+	.set_state_periodic	= omap2_gp_timer_set_periodic,
+	.set_state_oneshot	= omap2_gp_timer_shutdown,
+	.tick_resume		= omap2_gp_timer_shutdown,
 };
 
 static struct property device_disabled = {

arch/arm/mach-omap2/vc.c

@@ -563,7 +563,7 @@ struct i2c_init_data {
 	u8 hsscll_12;
 };
 
-static const __initdata struct i2c_init_data omap4_i2c_timing_data[] = {
+static const struct i2c_init_data const omap4_i2c_timing_data[] __initconst = {
 	{
 		.load = 50,
 		.loadbits = 0x3,

arch/arm/mach-omap2/voltagedomains3xxx_data.c

@@ -95,7 +95,7 @@ static struct voltagedomain *voltagedomains_am35xx[] __initdata = {
 };
 
 
-static const char *sys_clk_name __initdata = "sys_ck";
+static const char *const sys_clk_name __initconst = "sys_ck";
 
 void __init omap3xxx_voltagedomains_init(void)
 {

arch/arm/mach-omap2/voltagedomains44xx_data.c

@@ -92,7 +92,7 @@ static struct voltagedomain *voltagedomains_omap4[] __initdata = {
 	NULL,
 };
 
-static const char *sys_clk_name __initdata = "sys_clkin_ck";
+static const char *const sys_clk_name __initconst = "sys_clkin_ck";
 
 void __init omap44xx_voltagedomains_init(void)
 {

arch/arm/mach-omap2/voltagedomains54xx_data.c

@@ -78,7 +78,7 @@ static struct voltagedomain *voltagedomains_omap5[] __initdata = {
 	NULL,
 };
 
-static const char *sys_clk_name __initdata = "sys_clkin";
+static const char *const sys_clk_name __initconst = "sys_clkin";
 
 void __init omap54xx_voltagedomains_init(void)
 {

arch/arm/mach-orion5x/dns323-setup.c

@@ -236,9 +236,7 @@ static int __init dns323_read_mac_addr(void)
 	}
 
 	iounmap(mac_page);
-	printk("DNS-323: Found ethernet MAC address: ");
-	for (i = 0; i < 6; i++)
-		printk("%.2x%s", addr[i], (i < 5) ? ":" : ".\n");
+	printk("DNS-323: Found ethernet MAC address: %pM\n", addr);
 
 	memcpy(dns323_eth_data.mac_addr, addr, 6);
 

arch/arm/mach-orion5x/tsx09-common.c

@@ -101,9 +101,7 @@ static int __init qnap_tsx09_check_mac_addr(const char *addr_str)
 		addr[i] = byte;
 	}
 
-	printk(KERN_INFO "tsx09: found ethernet mac address ");
-	for (i = 0; i < 6; i++)
-		printk("%.2x%s", addr[i], (i < 5) ? ":" : ".\n");
+	printk(KERN_INFO "tsx09: found ethernet mac address %pM\n", addr);
 
 	memcpy(qnap_tsx09_eth_data.mac_addr, addr, 6);
 

arch/arm/mach-pxa/balloon3.c

@@ -496,18 +496,18 @@ static struct irq_chip balloon3_irq_chip = {
 	.irq_unmask	= balloon3_unmask_irq,
 };
 
-static void balloon3_irq_handler(unsigned int irq, struct irq_desc *desc)
+static void balloon3_irq_handler(unsigned int __irq, struct irq_desc *desc)
 {
 	unsigned long pending = __raw_readl(BALLOON3_INT_CONTROL_REG) &
 					balloon3_irq_enabled;
 	do {
-		/* clear useless edge notification */
-		if (desc->irq_data.chip->irq_ack) {
-			struct irq_data *d;
+		struct irq_data *d = irq_desc_get_irq_data(desc);
+		struct irq_chip *chip = irq_data_get_chip(d);
+		unsigned int irq;
 
-			d = irq_get_irq_data(BALLOON3_AUX_NIRQ);
-			desc->irq_data.chip->irq_ack(d);
-		}
+		/* clear useless edge notification */
+		if (chip->irq_ack)
+			chip->irq_ack(d);
 
 		while (pending) {
 			irq = BALLOON3_IRQ(0) + __ffs(pending);
@@ -528,7 +528,7 @@ static void __init balloon3_init_irq(void)
 	for (irq = BALLOON3_IRQ(0); irq <= BALLOON3_IRQ(7); irq++) {
 		irq_set_chip_and_handler(irq, &balloon3_irq_chip,
 					 handle_level_irq);
-		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+		irq_clear_status_flags(irq, IRQ_NOREQUEST | IRQ_NOPROBE);
 	}
 
 	irq_set_chained_handler(BALLOON3_AUX_NIRQ, balloon3_irq_handler);

arch/arm/mach-pxa/cm-x2xx-pci.c

@@ -29,8 +29,9 @@
 void __iomem *it8152_base_address;
 static int cmx2xx_it8152_irq_gpio;
 
-static void cmx2xx_it8152_irq_demux(unsigned int irq, struct irq_desc *desc)
+static void cmx2xx_it8152_irq_demux(unsigned int __irq, struct irq_desc *desc)
 {
+	unsigned int irq = irq_desc_get_irq(desc);
 	/* clear our parent irq */
 	desc->irq_data.chip->irq_ack(&desc->irq_data);
 

arch/arm/mach-pxa/irq.c

@@ -133,7 +133,6 @@ static int pxa_irq_map(struct irq_domain *h, unsigned int virq,
 	irq_set_chip_and_handler(virq, &pxa_internal_irq_chip,
 				 handle_level_irq);
 	irq_set_chip_data(virq, base);
-	set_irq_flags(virq, IRQF_VALID);
 
 	return 0;
 }