drm/omap: fix YUV422 rotation with TILER

TILER rotation with YUV422 pixelformats does not work at the moment. All
other pixel formats work, because the pixelformat's pixel size is equal
to tiler unit size (e.g. XR24's pixel size is 32 bits, and the TILER
unit size that has to be used is 32 bits).

For YUV422 formats this is not the case, as the TILER unit size has to
be 32 bits, but the pixel size is 16 bits. The end result is OCP errors
and sync losts.

This patch adds the code to adjust the variables for YUV422 formats.

We could make the code more generic by passing around the pixel format,
rotation type, angle and the tiler unit size, which would allow us to do
calculations without special case for YUV422. However, this would make
the code more complex, and at least for now this is much more easier to
handle with these two special cases for YUV422.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

drivers/gpu/drm/omapdrm/dss/dispc.c

@@ -1919,7 +1919,8 @@ static s32 pixinc(int pixels, u8 ps)
 static void calc_offset(u16 screen_width, u16 width,
 		u32 fourcc, bool fieldmode,
 		unsigned int field_offset, unsigned *offset0, unsigned *offset1,
-		s32 *row_inc, s32 *pix_inc, int x_predecim, int y_predecim)
+		s32 *row_inc, s32 *pix_inc, int x_predecim, int y_predecim,
+		enum omap_dss_rotation_type rotation_type, u8 rotation)
 {
 	u8 ps;
 
@@ -1927,6 +1928,20 @@ static void calc_offset(u16 screen_width, u16 width,
 
 	DSSDBG("scrw %d, width %d\n", screen_width, width);
 
+	if (rotation_type == OMAP_DSS_ROT_TILER &&
+	    (fourcc == DRM_FORMAT_UYVY || fourcc == DRM_FORMAT_YUYV) &&
+	    drm_rotation_90_or_270(rotation)) {
+		/*
+		 * HACK: ROW_INC needs to be calculated with TILER units.
+		 * We get such 'screen_width' that multiplying it with the
+		 * YUV422 pixel size gives the correct TILER container width.
+		 * However, 'width' is in pixels and multiplying it with YUV422
+		 * pixel size gives incorrect result. We thus multiply it here
+		 * with 2 to match the 32 bit TILER unit size.
+		 */
+		width *= 2;
+	}
+
 	/*
 	 * field 0 = even field = bottom field
 	 * field 1 = odd field = top field
@@ -2475,7 +2490,8 @@ static int dispc_ovl_setup_common(enum omap_plane_id plane,
 	calc_offset(screen_width, frame_width,
 			fourcc, fieldmode, field_offset,
 			&offset0, &offset1, &row_inc, &pix_inc,
-			x_predecim, y_predecim);
+			x_predecim, y_predecim,
+			rotation_type, rotation);
 
 	DSSDBG("offset0 %u, offset1 %u, row_inc %d, pix_inc %d\n",
 			offset0, offset1, row_inc, pix_inc);

drivers/gpu/drm/omapdrm/omap_fb.c

@@ -184,16 +184,30 @@ void omap_framebuffer_update_scanout(struct drm_framebuffer *fb,
 
 		orient = drm_rotation_to_tiler(state->rotation);
 
+		/*
+		 * omap_gem_rotated_paddr() wants the x & y in tiler units.
+		 * Usually tiler unit size is the same as the pixel size, except
+		 * for YUV422 formats, for which the tiler unit size is 32 bits
+		 * and pixel size is 16 bits.
+		 */
+		if (fb->format->format == DRM_FORMAT_UYVY ||
+				fb->format->format == DRM_FORMAT_YUYV) {
+			x /= 2;
+			w /= 2;
+		}
+
 		/* adjust x,y offset for invert: */
 		if (orient & MASK_Y_INVERT)
 			y += h - 1;
 		if (orient & MASK_X_INVERT)
 			x += w - 1;
 
+		/* Note: x and y are in TILER units, not pixels */
 		omap_gem_rotated_dma_addr(plane->bo, orient, x, y,
 					  &info->paddr);
 		info->rotation_type = OMAP_DSS_ROT_TILER;
 		info->rotation = state->rotation ?: DRM_MODE_ROTATE_0;
+		/* Note: stride in TILER units, not pixels */
 		info->screen_width  = omap_gem_tiled_stride(plane->bo, orient);
 	} else {
 		switch (state->rotation & DRM_MODE_ROTATE_MASK) {