Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Arnd Bergmann:
 "Here are a couple last-minute fixes for ARM SoCs.  Most of them are
  for the OMAP platforms, the rest are all for different platforms.

  OMAP:
     All dts fixes, mostly affecting voltages and pinctrl for various
     device drivers:

      - Regulator minimum voltage fixes for omap5
      - ISP syscon register offset fix for omap3
      - Fix regulator initial modes for n900
      - Fix omap5 pinctrl wkup instance size

  Allwinner:
     Remove incorrect constraints from a dcdc1 regulator

  Alltera SoCFPGA:
     Fix compilation in thumb2 mode

  Samsung exynos:
     Fix a potential oops in the pm-domain error handling

  Davinci:
     Avoid a link error if NVMEM is disabled

  Renesas:
     Do not mark an external uart clock as disabled, to allow probing
     the uarts"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: davinci: only use NVMEM when available
  ARM: SoCFPGA: Fix secondary CPU startup in thumb2 kernel
  ARM: dts: omap5: fix range of permitted wakeup pinmux registers
  ARM: dts: omap3-n900: Specify peripherals LDO regulators initial mode
  ARM: dts: omap3: Fix ISP syscon register offset
  ARM: dts: omap5-cm-t54: fix ldo1_reg and ldo4_reg ranges
  ARM: dts: omap5-board-common: fix ldo1_reg and ldo4_reg ranges
  arm64: dts: r8a7795: Don't disable referenced optional scif clock
  ARM: EXYNOS: Properly skip unitialized parent clock in power domain on
  ARM: dts: sun8i-q8-common: Do not set constraints on dc1sw regulator

arch/arm/boot/dts/omap3-n900.dts

@@ -329,6 +329,7 @@
 	regulator-name = "V28";
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <2800000>;
+	regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 	regulator-always-on; /* due to battery cover sensor */
 };
 
@@ -336,30 +337,35 @@
 	regulator-name = "VCSI";
 	regulator-min-microvolt = <1800000>;
 	regulator-max-microvolt = <1800000>;
+	regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 };
 
 &vaux3 {
 	regulator-name = "VMMC2_30";
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <3000000>;
+	regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 };
 
 &vaux4 {
 	regulator-name = "VCAM_ANA_28";
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <2800000>;
+	regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 };
 
 &vmmc1 {
 	regulator-name = "VMMC1";
 	regulator-min-microvolt = <1850000>;
 	regulator-max-microvolt = <3150000>;
+	regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 };
 
 &vmmc2 {
 	regulator-name = "V28_A";
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <3000000>;
+	regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 	regulator-always-on; /* due VIO leak to AIC34 VDDs */
 };
 
@@ -367,6 +373,7 @@
 	regulator-name = "VPLL";
 	regulator-min-microvolt = <1800000>;
 	regulator-max-microvolt = <1800000>;
+	regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 	regulator-always-on;
 };
 
@@ -374,6 +381,7 @@
 	regulator-name = "VSDI_CSI";
 	regulator-min-microvolt = <1800000>;
 	regulator-max-microvolt = <1800000>;
+	regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 	regulator-always-on;
 };
 
@@ -381,6 +389,7 @@
 	regulator-name = "VMMC2_IO_18";
 	regulator-min-microvolt = <1800000>;
 	regulator-max-microvolt = <1800000>;
+	regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
 };
 
 &vio {

arch/arm/boot/dts/omap34xx.dtsi

@@ -46,7 +46,7 @@
 			       0x480bd800 0x017c>;
 			interrupts = <24>;
 			iommus = <&mmu_isp>;
-			syscon = <&scm_conf 0xdc>;
+			syscon = <&scm_conf 0x6c>;
 			ti,phy-type = <OMAP3ISP_PHY_TYPE_COMPLEX_IO>;
 			#clock-cells = <1>;
 			ports {

arch/arm/boot/dts/omap5-board-common.dtsi

@@ -472,7 +472,7 @@
 				ldo1_reg: ldo1 {
 					/* VDDAPHY_CAM: vdda_csiport */
 					regulator-name = "ldo1";
-					regulator-min-microvolt = <1500000>;
+					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
 				};
 
@@ -498,7 +498,7 @@
 				ldo4_reg: ldo4 {
 					/* VDDAPHY_DISP: vdda_dsiport/hdmi */
 					regulator-name = "ldo4";
-					regulator-min-microvolt = <1500000>;
+					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
 				};
 

arch/arm/boot/dts/omap5-cm-t54.dts

@@ -513,7 +513,7 @@
 				ldo1_reg: ldo1 {
 					/* VDDAPHY_CAM: vdda_csiport */
 					regulator-name = "ldo1";
-					regulator-min-microvolt = <1500000>;
+					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
 				};
 
@@ -537,7 +537,7 @@
 				ldo4_reg: ldo4 {
 					/* VDDAPHY_DISP: vdda_dsiport/hdmi */
 					regulator-name = "ldo4";
-					regulator-min-microvolt = <1500000>;
+					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
 				};
 

arch/arm/boot/dts/omap5.dtsi

@@ -269,7 +269,7 @@
 			omap5_pmx_wkup: pinmux@c840 {
 				compatible = "ti,omap5-padconf",
 					     "pinctrl-single";
-				reg = <0xc840 0x0038>;
+				reg = <0xc840 0x003c>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 				#interrupt-cells = <1>;

arch/arm/boot/dts/sun8i-q8-common.dtsi

@@ -125,8 +125,6 @@
 };
 
 &reg_dc1sw {
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
 	regulator-name = "vcc-lcd";
 };
 

arch/arm/mach-davinci/board-mityomapl138.c

@@ -121,6 +121,11 @@ static void read_factory_config(struct nvmem_device *nvmem, void *context)
 	const char *partnum = NULL;
 	struct davinci_soc_info *soc_info = &davinci_soc_info;
 
+	if (!IS_BUILTIN(CONFIG_NVMEM)) {
+		pr_warn("Factory Config not available without CONFIG_NVMEM\n");
+		goto bad_config;
+	}
+
 	ret = nvmem_device_read(nvmem, 0, sizeof(factory_config),
 				&factory_config);
 	if (ret != sizeof(struct factory_config)) {

arch/arm/mach-davinci/common.c

@@ -33,6 +33,11 @@ void davinci_get_mac_addr(struct nvmem_device *nvmem, void *context)
 	char *mac_addr = davinci_soc_info.emac_pdata->mac_addr;
 	off_t offset = (off_t)context;
 
+	if (!IS_BUILTIN(CONFIG_NVMEM)) {
+		pr_warn("Cannot read MAC addr from EEPROM without CONFIG_NVMEM\n");
+		return;
+	}
+
 	/* Read MAC addr from EEPROM */
 	if (nvmem_device_read(nvmem, offset, ETH_ALEN, mac_addr) == ETH_ALEN)
 		pr_info("Read MAC addr from EEPROM: %pM\n", mac_addr);

arch/arm/mach-exynos/pm_domains.c

@@ -92,7 +92,7 @@ static int exynos_pd_power(struct generic_pm_domain *domain, bool power_on)
 			if (IS_ERR(pd->clk[i]))
 				break;
 
-			if (IS_ERR(pd->clk[i]))
+			if (IS_ERR(pd->pclk[i]))
 				continue; /* Skip on first power up */
 			if (clk_set_parent(pd->clk[i], pd->pclk[i]))
 				pr_err("%s: error setting parent to clock%d\n",

arch/arm/mach-socfpga/headsmp.S

@@ -13,6 +13,7 @@
 #include <asm/assembler.h>
 
 	.arch	armv7-a
+	.arm
 
 ENTRY(secondary_trampoline)
 	/* CPU1 will always fetch from 0x0 when it is brought out of reset.

arch/arm64/boot/dts/renesas/r8a7795.dtsi

@@ -120,7 +120,6 @@
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <0>;
-		status = "disabled";
 	};
 
 	soc {