Maxim/driver: Add driver for maxim ds26522

Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/wan/Kconfig

@@ -291,6 +291,17 @@ config FSL_UCC_HDLC
 	  To compile this driver as a module, choose M here: the
 	  module will be called fsl_ucc_hdlc.
 
+config SLIC_DS26522
+	tristate "Slic Maxim ds26522 card support"
+	depends on SPI
+	depends on FSL_SOC || ARCH_MXC || ARCH_LAYERSCAPE
+	help
+	  This module initializes and configures the slic maxim card
+	  in T1 or E1 mode.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called slic_ds26522.
+
 config DSCC4_PCISYNC
 	bool "Etinc PCISYNC features"
 	depends on DSCC4

drivers/net/wan/Makefile

@@ -33,6 +33,7 @@ obj-$(CONFIG_PCI200SYN)		+= pci200syn.o
 obj-$(CONFIG_PC300TOO)		+= pc300too.o
 obj-$(CONFIG_IXP4XX_HSS)	+= ixp4xx_hss.o
 obj-$(CONFIG_FSL_UCC_HDLC)	+= fsl_ucc_hdlc.o
+obj-$(CONFIG_SLIC_DS26522)	+= slic_ds26522.o
 
 clean-files := wanxlfw.inc
 $(obj)/wanxl.o:	$(obj)/wanxlfw.inc

drivers/net/wan/slic_ds26522.c

@@ -0,0 +1,255 @@
+/*
+ * drivers/net/wan/slic_ds26522.c
+ *
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ *
+ * Author:Zhao Qiang<qiang.zhao@nxp.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/bitrev.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/kthread.h>
+#include <linux/spi/spi.h>
+#include <linux/wait.h>
+#include <linux/param.h>
+#include <linux/delay.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/io.h>
+#include "slic_ds26522.h"
+
+#define DRV_NAME "ds26522"
+
+#define SLIC_TRANS_LEN 1
+#define SLIC_TWO_LEN 2
+#define SLIC_THREE_LEN 3
+
+static struct spi_device *g_spi;
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Zhao Qiang<B45475@freescale.com>");
+
+/* the read/write format of address is
+ * w/r|A13|A12|A11|A10|A9|A8|A7|A6|A5|A4|A3|A2|A1|A0|x
+ */
+static void slic_write(struct spi_device *spi, u16 addr,
+		       u8 data)
+{
+	u8 temp[3];
+
+	addr = bitrev16(addr) >> 1;
+	data = bitrev8(data);
+	temp[0] = (u8)((addr >> 8) & 0x7f);
+	temp[1] = (u8)(addr & 0xfe);
+	temp[2] = data;
+
+	/* write spi addr and value */
+	spi_write(spi, &temp[0], SLIC_THREE_LEN);
+}
+
+static u8 slic_read(struct spi_device *spi, u16 addr)
+{
+	u8 temp[2];
+	u8 data;
+
+	addr = bitrev16(addr) >> 1;
+	temp[0] = (u8)(((addr >> 8) & 0x7f) | 0x80);
+	temp[1] = (u8)(addr & 0xfe);
+
+	spi_write_then_read(spi, &temp[0], SLIC_TWO_LEN, &data,
+			    SLIC_TRANS_LEN);
+
+	data = bitrev8(data);
+	return data;
+}
+
+static bool get_slic_product_code(struct spi_device *spi)
+{
+	u8 device_id;
+
+	device_id = slic_read(spi, DS26522_IDR_ADDR);
+	if ((device_id & 0xf8) == 0x68)
+		return true;
+	else
+		return false;
+}
+
+static void ds26522_e1_spec_config(struct spi_device *spi)
+{
+	/* Receive E1 Mode, Framer Disabled */
+	slic_write(spi, DS26522_RMMR_ADDR, DS26522_RMMR_E1);
+
+	/* Transmit E1 Mode, Framer Disable */
+	slic_write(spi, DS26522_TMMR_ADDR, DS26522_TMMR_E1);
+
+	/* Receive E1 Mode Framer Enable */
+	slic_write(spi, DS26522_RMMR_ADDR,
+		   slic_read(spi, DS26522_RMMR_ADDR) | DS26522_RMMR_FRM_EN);
+
+	/* Transmit E1 Mode Framer Enable */
+	slic_write(spi, DS26522_TMMR_ADDR,
+		   slic_read(spi, DS26522_TMMR_ADDR) | DS26522_TMMR_FRM_EN);
+
+	/* RCR1, receive E1 B8zs & ESF */
+	slic_write(spi, DS26522_RCR1_ADDR,
+		   DS26522_RCR1_E1_HDB3 | DS26522_RCR1_E1_CCS);
+
+	/* RSYSCLK=2.048MHz, RSYNC-Output */
+	slic_write(spi, DS26522_RIOCR_ADDR,
+		   DS26522_RIOCR_2048KHZ | DS26522_RIOCR_RSIO_OUT);
+
+	/* TCR1 Transmit E1 b8zs */
+	slic_write(spi, DS26522_TCR1_ADDR, DS26522_TCR1_TB8ZS);
+
+	/* TSYSCLK=2.048MHz, TSYNC-Output */
+	slic_write(spi, DS26522_TIOCR_ADDR,
+		   DS26522_TIOCR_2048KHZ | DS26522_TIOCR_TSIO_OUT);
+
+	/* Set E1TAF */
+	slic_write(spi, DS26522_E1TAF_ADDR, DS26522_E1TAF_DEFAULT);
+
+	/* Set E1TNAF register */
+	slic_write(spi, DS26522_E1TNAF_ADDR, DS26522_E1TNAF_DEFAULT);
+
+	/* Receive E1 Mode Framer Enable & init Done */
+	slic_write(spi, DS26522_RMMR_ADDR, slic_read(spi, DS26522_RMMR_ADDR) |
+		   DS26522_RMMR_INIT_DONE);
+
+	/* Transmit E1 Mode Framer Enable & init Done */
+	slic_write(spi, DS26522_TMMR_ADDR, slic_read(spi, DS26522_TMMR_ADDR) |
+		   DS26522_TMMR_INIT_DONE);
+
+	/* Configure LIU E1 mode */
+	slic_write(spi, DS26522_LTRCR_ADDR, DS26522_LTRCR_E1);
+
+	/* E1 Mode default 75 ohm w/Transmit Impedance Matlinking */
+	slic_write(spi, DS26522_LTITSR_ADDR,
+		   DS26522_LTITSR_TLIS_75OHM | DS26522_LTITSR_LBOS_75OHM);
+
+	/* E1 Mode default 75 ohm Long Haul w/Receive Impedance Matlinking */
+	slic_write(spi, DS26522_LRISMR_ADDR,
+		   DS26522_LRISMR_75OHM | DS26522_LRISMR_MAX);
+
+	/* Enable Transmit output */
+	slic_write(spi, DS26522_LMCR_ADDR, DS26522_LMCR_TE);
+}
+
+static int slic_ds26522_init_configure(struct spi_device *spi)
+{
+	u16 addr;
+
+	/* set clock */
+	slic_write(spi, DS26522_GTCCR_ADDR, DS26522_GTCCR_BPREFSEL_REFCLKIN |
+			DS26522_GTCCR_BFREQSEL_2048KHZ |
+			DS26522_GTCCR_FREQSEL_2048KHZ);
+	slic_write(spi, DS26522_GTCR2_ADDR, DS26522_GTCR2_TSSYNCOUT);
+	slic_write(spi, DS26522_GFCR_ADDR, DS26522_GFCR_BPCLK_2048KHZ);
+
+	/* set gtcr */
+	slic_write(spi, DS26522_GTCR1_ADDR, DS26522_GTCR1);
+
+	/* Global LIU Software Reset Register */
+	slic_write(spi, DS26522_GLSRR_ADDR, DS26522_GLSRR_RESET);
+
+	/* Global Framer and BERT Software Reset Register */
+	slic_write(spi, DS26522_GFSRR_ADDR, DS26522_GFSRR_RESET);
+
+	usleep_range(100, 120);
+
+	slic_write(spi, DS26522_GLSRR_ADDR, DS26522_GLSRR_NORMAL);
+	slic_write(spi, DS26522_GFSRR_ADDR, DS26522_GFSRR_NORMAL);
+
+	/* Perform RX/TX SRESET,Reset receiver */
+	slic_write(spi, DS26522_RMMR_ADDR, DS26522_RMMR_SFTRST);
+
+	/* Reset tranceiver */
+	slic_write(spi, DS26522_TMMR_ADDR, DS26522_TMMR_SFTRST);
+
+	usleep_range(100, 120);
+
+	/* Zero all Framer Registers */
+	for (addr = DS26522_RF_ADDR_START; addr <= DS26522_RF_ADDR_END;
+	     addr++)
+		slic_write(spi, addr, 0);
+
+	for (addr = DS26522_TF_ADDR_START; addr <= DS26522_TF_ADDR_END;
+	     addr++)
+		slic_write(spi, addr, 0);
+
+	for (addr = DS26522_LIU_ADDR_START; addr <= DS26522_LIU_ADDR_END;
+	     addr++)
+		slic_write(spi, addr, 0);
+
+	for (addr = DS26522_BERT_ADDR_START; addr <= DS26522_BERT_ADDR_END;
+	     addr++)
+		slic_write(spi, addr, 0);
+
+	/* setup ds26522 for E1 specification */
+	ds26522_e1_spec_config(spi);
+
+	slic_write(spi, DS26522_GTCR1_ADDR, 0x00);
+
+	return 0;
+}
+
+static int slic_ds26522_remove(struct spi_device *spi)
+{
+	pr_info("DS26522 module uninstalled\n");
+	return 0;
+}
+
+static int slic_ds26522_probe(struct spi_device *spi)
+{
+	int ret = 0;
+
+	g_spi = spi;
+	spi->bits_per_word = 8;
+
+	if (!get_slic_product_code(spi))
+		return ret;
+
+	ret = slic_ds26522_init_configure(spi);
+	if (ret == 0)
+		pr_info("DS26522 cs%d configurated\n", spi->chip_select);
+
+	return ret;
+}
+
+static const struct of_device_id slic_ds26522_match[] = {
+	{
+	 .compatible = "maxim,ds26522",
+	 },
+	{},
+};
+
+static struct spi_driver slic_ds26522_driver = {
+	.driver = {
+		   .name = "ds26522",
+		   .bus = &spi_bus_type,
+		   .owner = THIS_MODULE,
+		   .of_match_table = slic_ds26522_match,
+		   },
+	.probe = slic_ds26522_probe,
+	.remove = slic_ds26522_remove,
+};
+
+static int __init slic_ds26522_init(void)
+{
+	return spi_register_driver(&slic_ds26522_driver);
+}
+
+static void __exit slic_ds26522_exit(void)
+{
+	spi_unregister_driver(&slic_ds26522_driver);
+}
+
+module_init(slic_ds26522_init);
+module_exit(slic_ds26522_exit);

drivers/net/wan/slic_ds26522.h

@@ -0,0 +1,134 @@
+/*
+ * drivers/tdm/line_ctrl/slic_ds26522.h
+ *
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * Author: Zhao Qiang <B45475@freescale.com>
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#define DS26522_RF_ADDR_START	0x00
+#define DS26522_RF_ADDR_END	0xef
+#define DS26522_GLB_ADDR_START	0xf0
+#define DS26522_GLB_ADDR_END	0xff
+#define DS26522_TF_ADDR_START	0x100
+#define DS26522_TF_ADDR_END	0x1ef
+#define DS26522_LIU_ADDR_START	0x1000
+#define DS26522_LIU_ADDR_END	0x101f
+#define DS26522_TEST_ADDR_START	0x1008
+#define DS26522_TEST_ADDR_END	0x101f
+#define DS26522_BERT_ADDR_START	0x1100
+#define DS26522_BERT_ADDR_END	0x110f
+
+#define DS26522_RMMR_ADDR	0x80
+#define DS26522_RCR1_ADDR	0x81
+#define DS26522_RCR3_ADDR	0x83
+#define DS26522_RIOCR_ADDR	0x84
+
+#define DS26522_GTCR1_ADDR	0xf0
+#define DS26522_GFCR_ADDR	0xf1
+#define DS26522_GTCR2_ADDR	0xf2
+#define DS26522_GTCCR_ADDR	0xf3
+#define DS26522_GLSRR_ADDR	0xf5
+#define DS26522_GFSRR_ADDR	0xf6
+#define DS26522_IDR_ADDR	0xf8
+
+#define DS26522_E1TAF_ADDR	0x164
+#define DS26522_E1TNAF_ADDR	0x165
+#define DS26522_TMMR_ADDR	0x180
+#define DS26522_TCR1_ADDR	0x181
+#define DS26522_TIOCR_ADDR	0x184
+
+#define DS26522_LTRCR_ADDR	0x1000
+#define DS26522_LTITSR_ADDR	0x1001
+#define DS26522_LMCR_ADDR	0x1002
+#define DS26522_LRISMR_ADDR	0x1007
+
+#define MAX_NUM_OF_CHANNELS	8
+#define PQ_MDS_8E1T1_BRD_REV	0x00
+#define PQ_MDS_8E1T1_PLD_REV	0x00
+
+#define DS26522_GTCCR_BPREFSEL_REFCLKIN	0xa0
+#define DS26522_GTCCR_BFREQSEL_1544KHZ	0x08
+#define DS26522_GTCCR_FREQSEL_1544KHZ	0x04
+#define DS26522_GTCCR_BFREQSEL_2048KHZ	0x00
+#define DS26522_GTCCR_FREQSEL_2048KHZ	0x00
+
+#define DS26522_GFCR_BPCLK_2048KHZ	0x00
+
+#define DS26522_GTCR2_TSSYNCOUT	0x02
+#define DS26522_GTCR1	0x00
+
+#define DS26522_GFSRR_RESET	0x01
+#define DS26522_GFSRR_NORMAL	0x00
+
+#define DS26522_GLSRR_RESET	0x01
+#define DS26522_GLSRR_NORMAL	0x00
+
+#define DS26522_RMMR_SFTRST	0x02
+#define DS26522_RMMR_FRM_EN	0x80
+#define DS26522_RMMR_INIT_DONE	0x40
+#define DS26522_RMMR_T1		0x00
+#define DS26522_RMMR_E1		0x01
+
+#define DS26522_E1TAF_DEFAULT	0x1b
+#define DS26522_E1TNAF_DEFAULT	0x40
+
+#define DS26522_TMMR_SFTRST	0x02
+#define DS26522_TMMR_FRM_EN	0x80
+#define DS26522_TMMR_INIT_DONE	0x40
+#define DS26522_TMMR_T1		0x00
+#define DS26522_TMMR_E1		0x01
+
+#define DS26522_RCR1_T1_SYNCT	0x80
+#define DS26522_RCR1_T1_RB8ZS	0x40
+#define DS26522_RCR1_T1_SYNCC	0x08
+
+#define DS26522_RCR1_E1_HDB3	0x40
+#define DS26522_RCR1_E1_CCS	0x20
+
+#define DS26522_RIOCR_1544KHZ	0x00
+#define DS26522_RIOCR_2048KHZ	0x10
+#define DS26522_RIOCR_RSIO_OUT	0x00
+
+#define DS26522_RCR3_FLB	0x01
+
+#define DS26522_TIOCR_1544KHZ	0x00
+#define DS26522_TIOCR_2048KHZ	0x10
+#define DS26522_TIOCR_TSIO_OUT	0x04
+
+#define DS26522_TCR1_TB8ZS	0x04
+
+#define DS26522_LTRCR_T1	0x02
+#define DS26522_LTRCR_E1	0x00
+
+#define DS26522_LTITSR_TLIS_75OHM	0x00
+#define DS26522_LTITSR_LBOS_75OHM	0x00
+#define DS26522_LTITSR_TLIS_100OHM	0x10
+#define DS26522_LTITSR_TLIS_0DB_CSU	0x00
+
+#define DS26522_LRISMR_75OHM	0x00
+#define DS26522_LRISMR_100OHM	0x10
+#define DS26522_LRISMR_MAX	0x03
+
+#define DS26522_LMCR_TE	0x01
+
+enum line_rate {
+	LINE_RATE_T1,	/* T1 line rate (1.544 Mbps)      */
+	LINE_RATE_E1	/* E1 line rate (2.048 Mbps)     */
+};
+
+enum tdm_trans_mode {
+	NORMAL = 0,
+	FRAMER_LB
+};
+
+enum card_support_type {
+	LM_CARD = 0,
+	DS26522_CARD,
+	NO_CARD
+};