Merge tag 'fixes-for-v4.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v4.15-rc4

We have a few fixes on dwc3:

- one fix which only happens with some implementations where we need to
  wait longer for some commands to finish.

- Another fix for high-bandwidth isochronous endpoint programming making
  sure that we send the correct DATA tokens in the correct sequence

- A couple PM fixes on dwc3-of-simple

The other synopsys controller driver (dwc2) got a fix for FIFO size
programming.

Other than these, we have a couple Kconfig fixes making sure that
dependencies are properly setup.

Documentation/devicetree/bindings/arm/ccn.txt

@@ -15,7 +15,7 @@ Required properties:
 
 Example:
 
-	ccn@0x2000000000 {
+	ccn@2000000000 {
 		compatible = "arm,ccn-504";
 		reg = <0x20 0x00000000 0 0x1000000>;
 		interrupts = <0 181 4>;

Documentation/devicetree/bindings/arm/omap/crossbar.txt

@@ -49,7 +49,7 @@ An interrupt consumer on an SoC using crossbar will use:
 	interrupts = <GIC_SPI request_number interrupt_level>
 
 Example:
-	device_x@0x4a023000 {
+	device_x@4a023000 {
 		/* Crossbar 8 used */
 		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 		...

Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-mc.txt

@@ -8,7 +8,7 @@ Required properties:
 - interrupts : Should contain MC General interrupt.
 
 Example:
-	memory-controller@0x7000f000 {
+	memory-controller@7000f000 {
 		compatible = "nvidia,tegra20-mc";
 		reg = <0x7000f000 0x024
 		       0x7000f03c 0x3c4>;

Documentation/devicetree/bindings/clock/axi-clkgen.txt

@@ -17,7 +17,7 @@ Optional properties:
 - clock-output-names : From common clock binding.
 
 Example:
-	clock@0xff000000 {
+	clock@ff000000 {
 		compatible = "adi,axi-clkgen";
 		#clock-cells = <0>;
 		reg = <0xff000000 0x1000>;

Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt

@@ -23,7 +23,7 @@ Example:
 		clocks = <&clk_osc>;
 	};
 
-	aux: aux@0x7e215004 {
+	aux: aux@7e215004 {
 		compatible = "brcm,bcm2835-aux";
 		#clock-cells = <1>;
 		reg = <0x7e215000 0x8>;

Documentation/devicetree/bindings/clock/exynos4-clock.txt

@@ -24,7 +24,7 @@ tree sources.
 
 Example 1: An example of a clock controller node is listed below.
 
-	clock: clock-controller@0x10030000 {
+	clock: clock-controller@10030000 {
 		compatible = "samsung,exynos4210-clock";
 		reg = <0x10030000 0x20000>;
 		#clock-cells = <1>;

Documentation/devicetree/bindings/clock/exynos5250-clock.txt

@@ -22,7 +22,7 @@ tree sources.
 
 Example 1: An example of a clock controller node is listed below.
 
-	clock: clock-controller@0x10010000 {
+	clock: clock-controller@10010000 {
 		compatible = "samsung,exynos5250-clock";
 		reg = <0x10010000 0x30000>;
 		#clock-cells = <1>;

Documentation/devicetree/bindings/clock/exynos5410-clock.txt

@@ -30,7 +30,7 @@ Example 1: An example of a clock controller node is listed below.
 		#clock-cells = <0>;
 	};
 
-	clock: clock-controller@0x10010000 {
+	clock: clock-controller@10010000 {
 		compatible = "samsung,exynos5410-clock";
 		reg = <0x10010000 0x30000>;
 		#clock-cells = <1>;

Documentation/devicetree/bindings/clock/exynos5420-clock.txt

@@ -23,7 +23,7 @@ tree sources.
 
 Example 1: An example of a clock controller node is listed below.
 
-	clock: clock-controller@0x10010000 {
+	clock: clock-controller@10010000 {
 		compatible = "samsung,exynos5420-clock";
 		reg = <0x10010000 0x30000>;
 		#clock-cells = <1>;

Documentation/devicetree/bindings/clock/exynos5440-clock.txt

@@ -21,7 +21,7 @@ tree sources.
 
 Example: An example of a clock controller node is listed below.
 
-	clock: clock-controller@0x10010000 {
+	clock: clock-controller@10010000 {
 		compatible = "samsung,exynos5440-clock";
 		reg = <0x160000 0x10000>;
 		#clock-cells = <1>;

Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt

@@ -14,7 +14,7 @@ Required properties:
 
 Example:
 
-pllctrl: pll-controller@0x02310000 {
+pllctrl: pll-controller@02310000 {
 	compatible = "ti,keystone-pllctrl", "syscon";
 	reg = <0x02310000 0x200>;
 };

Documentation/devicetree/bindings/clock/zx296702-clk.txt

@@ -20,13 +20,13 @@ ID in its "clocks" phandle cell. See include/dt-bindings/clock/zx296702-clock.h
 for the full list of zx296702 clock IDs.
 
 
-topclk: topcrm@0x09800000 {
+topclk: topcrm@09800000 {
         compatible = "zte,zx296702-topcrm-clk";
         reg = <0x09800000 0x1000>;
         #clock-cells = <1>;
 };
 
-uart0: serial@0x09405000 {
+uart0: serial@09405000 {
         compatible = "zte,zx296702-uart";
         reg = <0x09405000 0x1000>;
         interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;

Documentation/devicetree/bindings/crypto/fsl-sec4.txt

@@ -456,7 +456,7 @@ System ON/OFF key driver
       Definition: this is phandle to the register map node.
 
 EXAMPLE:
-	snvs-pwrkey@0x020cc000 {
+	snvs-pwrkey@020cc000 {
 		compatible = "fsl,sec-v4.0-pwrkey";
 		regmap = <&snvs>;
 		interrupts = <0 4 0x4>
@@ -545,7 +545,7 @@ FULL EXAMPLE
 			interrupts = <93 2>;
 		};
 
-		snvs-pwrkey@0x020cc000 {
+		snvs-pwrkey@020cc000 {
 			compatible = "fsl,sec-v4.0-pwrkey";
 			regmap = <&sec_mon>;
 			interrupts = <0 4 0x4>;

Documentation/devicetree/bindings/devfreq/event/rockchip-dfi.txt

@@ -9,7 +9,7 @@ Required properties:
 - clock-names : the name of clock used by the DFI, must be "pclk_ddr_mon";
 
 Example:
-	dfi: dfi@0xff630000 {
+	dfi: dfi@ff630000 {
 		compatible = "rockchip,rk3399-dfi";
 		reg = <0x00 0xff630000 0x00 0x4000>;
 		rockchip,pmu = <&pmugrf>;

Documentation/devicetree/bindings/display/atmel,lcdc.txt

@@ -27,7 +27,7 @@ Optional properties:
 
 Example:
 
-	fb0: fb@0x00500000 {
+	fb0: fb@00500000 {
 		compatible = "atmel,at91sam9g45-lcdc";
 		reg = <0x00500000 0x1000>;
 		interrupts = <23 3 0>;
@@ -41,7 +41,7 @@ Example:
 
 Example for fixed framebuffer memory:
 
-	fb0: fb@0x00500000 {
+	fb0: fb@00500000 {
 		compatible = "atmel,at91sam9263-lcdc";
 		reg = <0x00700000 0x1000 0x70000000 0x200000>;
 		[...]

Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt

@@ -73,7 +73,7 @@ Hypervisor OS configuration:
 		max-read-transactions = <31>;
 		channel-reset-timeout-cycles = <0x500>;
 
-		hidma_24: dma-controller@0x5c050000 {
+		hidma_24: dma-controller@5c050000 {
 			compatible = "qcom,hidma-1.0";
 			reg = <0 0x5c050000 0x0 0x1000>,
 			      <0 0x5c0b0000 0x0 0x1000>;
@@ -85,7 +85,7 @@ Hypervisor OS configuration:
 
 Guest OS configuration:
 
-	hidma_24: dma-controller@0x5c050000 {
+	hidma_24: dma-controller@5c050000 {
 		compatible = "qcom,hidma-1.0";
 		reg = <0 0x5c050000 0x0 0x1000>,
 		      <0 0x5c0b0000 0x0 0x1000>;

Documentation/devicetree/bindings/dma/zxdma.txt

@@ -13,7 +13,7 @@ Required properties:
 Example:
 
 Controller:
-	dma: dma-controller@0x09c00000{
+	dma: dma-controller@09c00000{
 		compatible = "zte,zx296702-dma";
 		reg = <0x09c00000 0x1000>;
 		clocks = <&topclk ZX296702_DMA_ACLK>;

Documentation/devicetree/bindings/eeprom/at25.txt

@@ -1,7 +1,12 @@
 EEPROMs (SPI) compatible with Atmel at25.
 
 Required properties:
-- compatible : "atmel,at25".
+- compatible : Should be "<vendor>,<type>", and generic value "atmel,at25".
+  Example "<vendor>,<type>" values:
+    "microchip,25lc040"
+    "st,m95m02"
+    "st,m95256"
+
 - reg : chip select number
 - spi-max-frequency : max spi frequency to use
 - pagesize : size of the eeprom page
@@ -13,7 +18,7 @@ Optional properties:
 - spi-cpol : SPI inverse clock polarity, as per spi-bus bindings.
 - read-only : this parameter-less property disables writes to the eeprom
 
-Obsolete legacy properties are can be used in place of "size", "pagesize",
+Obsolete legacy properties can be used in place of "size", "pagesize",
 "address-width", and "read-only":
 - at25,byte-len : total eeprom size in bytes
 - at25,addr-mode : addr-mode flags, as defined in include/linux/spi/eeprom.h
@@ -22,8 +27,8 @@ Obsolete legacy properties are can be used in place of "size", "pagesize",
 Additional compatible properties are also allowed.
 
 Example:
-	at25@0 {
-		compatible = "atmel,at25", "st,m95256";
+	eeprom@0 {
+		compatible = "st,m95256", "atmel,at25";
 		reg = <0>
 		spi-max-frequency = <5000000>;
 		spi-cpha;

Documentation/devicetree/bindings/gpio/gpio-altera.txt

@@ -30,7 +30,7 @@ Optional properties:
 
 Example:
 
-gpio_altr: gpio@0xff200000 {
+gpio_altr: gpio@ff200000 {
 	compatible = "altr,pio-1.0";
 	reg = <0xff200000 0x10>;
 	interrupts = <0 45 4>;

Documentation/devicetree/bindings/i2c/i2c-jz4780.txt

@@ -18,7 +18,7 @@ Optional properties:
 Example
 
 / {
-	i2c4: i2c4@0x10054000 {
+	i2c4: i2c4@10054000 {
 		compatible = "ingenic,jz4780-i2c";
 		reg = <0x10054000 0x1000>;
 

Documentation/devicetree/bindings/iio/pressure/hp03.txt

@@ -10,7 +10,7 @@ Required properties:
 
 Example:
 
-hp03@0x77 {
+hp03@77 {
 	compatible = "hoperf,hp03";
 	reg = <0x77>;
 	xclr-gpio = <&portc 0 0x0>;

Documentation/devicetree/bindings/input/touchscreen/bu21013.txt

@@ -15,7 +15,7 @@ Optional properties:
 Example:
 
 	i2c@80110000 {
-		bu21013_tp@0x5c {
+		bu21013_tp@5c {
 			compatible = "rohm,bu21013_tp";
 			reg = <0x5c>;
 			touch-gpio = <&gpio2 20 0x4>;

Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt

@@ -155,7 +155,7 @@ Example:
 		      <0x0 0xe112f000 0 0x02000>,
 		      <0x0 0xe1140000 0 0x10000>,
 		      <0x0 0xe1160000 0 0x10000>;
-		v2m0: v2m@0x8000 {
+		v2m0: v2m@8000 {
 			compatible = "arm,gic-v2m-frame";
 			msi-controller;
 			reg = <0x0 0x80000 0 0x1000>;
@@ -163,7 +163,7 @@ Example:
 
 		....
 
-		v2mN: v2m@0x9000 {
+		v2mN: v2m@9000 {
 			compatible = "arm,gic-v2m-frame";
 			msi-controller;
 			reg = <0x0 0x90000 0 0x1000>;

Documentation/devicetree/bindings/interrupt-controller/img,meta-intc.txt

@@ -71,7 +71,7 @@ Example 2:
 	 * An interrupt generating device that is wired to a Meta external
 	 * trigger block.
 	 */
-	uart1: uart@0x02004c00 {
+	uart1: uart@02004c00 {
 		// Interrupt source '5' that is level-sensitive.
 		// Note that there are only two cells as specified in the
 		// interrupt parent's '#interrupt-cells' property.

Documentation/devicetree/bindings/interrupt-controller/img,pdc-intc.txt

@@ -51,7 +51,7 @@ Example 1:
 	/*
 	 * TZ1090 PDC block
 	 */
-	pdc: pdc@0x02006000 {
+	pdc: pdc@02006000 {
 		// This is an interrupt controller node.
 		interrupt-controller;
 

Documentation/devicetree/bindings/interrupt-controller/st,spear3xx-shirq.txt

@@ -39,7 +39,7 @@ Example:
 
 The following is an example from the SPEAr320 SoC dtsi file.
 
-shirq: interrupt-controller@0xb3000000 {
+shirq: interrupt-controller@b3000000 {
 	compatible = "st,spear320-shirq";
 	reg = <0xb3000000 0x1000>;
 	interrupts = <28 29 30 1>;

Documentation/devicetree/bindings/mailbox/altera-mailbox.txt

@@ -14,7 +14,7 @@ Optional properties:
 			depends on the interrupt controller parent.
 
 Example:
-	mbox_tx: mailbox@0x100 {
+	mbox_tx: mailbox@100 {
 		compatible = "altr,mailbox-1.0";
 		reg = <0x100 0x8>;
 		interrupt-parent = < &gic_0 >;
@@ -22,7 +22,7 @@ Example:
 		#mbox-cells = <1>;
 	};
 
-	mbox_rx: mailbox@0x200 {
+	mbox_rx: mailbox@200 {
 		compatible = "altr,mailbox-1.0";
 		reg = <0x200 0x8>;
 		interrupt-parent = < &gic_0 >;
@@ -40,7 +40,7 @@ support only one channel).The equivalent "mbox-names" property value can be
 used to give a name to the communication channel to be used by the client user.
 
 Example:
-	mclient0: mclient0@0x400 {
+	mclient0: mclient0@400 {
 		compatible = "client-1.0";
 		reg = <0x400 0x10>;
 		mbox-names = "mbox-tx", "mbox-rx";

Documentation/devicetree/bindings/mailbox/brcm,iproc-pdc-mbox.txt

@@ -15,7 +15,7 @@ Optional properties:
 - brcm,use-bcm-hdr:  present if a BCM header precedes each frame.
 
 Example:
-	pdc0: iproc-pdc0@0x612c0000 {
+	pdc0: iproc-pdc0@612c0000 {
 		compatible = "brcm,iproc-pdc-mbox";
 		reg = <0 0x612c0000 0 0x445>;  /* PDC FS0 regs */
 		interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;

Documentation/devicetree/bindings/media/exynos5-gsc.txt

@@ -17,7 +17,7 @@ Optional properties:
 
 Example:
 
-gsc_0:  gsc@0x13e00000 {
+gsc_0:  gsc@13e00000 {
 	compatible = "samsung,exynos5250-gsc";
 	reg = <0x13e00000 0x1000>;
 	interrupts = <0 85 0>;

Documentation/devicetree/bindings/media/mediatek-vcodec.txt

@@ -68,7 +68,7 @@ vcodec_dec: vcodec@16000000 {
                   "vdec_bus_clk_src";
   };
 
-  vcodec_enc: vcodec@0x18002000 {
+  vcodec_enc: vcodec@18002000 {
     compatible = "mediatek,mt8173-vcodec-enc";
     reg = <0 0x18002000 0 0x1000>,    /*VENC_SYS*/
           <0 0x19002000 0 0x1000>;    /*VENC_LT_SYS*/

Documentation/devicetree/bindings/media/rcar_vin.txt

@@ -44,7 +44,7 @@ Device node example
 	       vin0 = &vin0;
 	};
 
-        vin0: vin@0xe6ef0000 {
+        vin0: vin@e6ef0000 {
                 compatible = "renesas,vin-r8a7790", "renesas,rcar-gen2-vin";
                 clocks = <&mstp8_clks R8A7790_CLK_VIN0>;
                 reg = <0 0xe6ef0000 0 0x1000>;

Documentation/devicetree/bindings/media/samsung-fimc.txt

@@ -138,7 +138,7 @@ Example:
 		};
 
 		/* MIPI CSI-2 bus IF sensor */
-		s5c73m3: sensor@0x1a {
+		s5c73m3: sensor@1a {
 			compatible = "samsung,s5c73m3";
 			reg = <0x1a>;
 			vddio-supply = <...>;

Documentation/devicetree/bindings/media/sh_mobile_ceu.txt

@@ -8,7 +8,7 @@ Bindings, specific for the sh_mobile_ceu_camera.c driver:
 
 Example:
 
-ceu0: ceu@0xfe910000 {
+ceu0: ceu@fe910000 {
 	compatible = "renesas,sh-mobile-ceu";
 	reg = <0xfe910000 0xa0>;
 	interrupt-parent = <&intcs>;

Documentation/devicetree/bindings/media/video-interfaces.txt

@@ -154,7 +154,7 @@ imx074 is linked to ceu0 through the MIPI CSI-2 receiver (csi2). ceu0 has a
 'port' node which may indicate that at any time only one of the following data
 pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0.
 
-	ceu0: ceu@0xfe910000 {
+	ceu0: ceu@fe910000 {
 		compatible = "renesas,sh-mobile-ceu";
 		reg = <0xfe910000 0xa0>;
 		interrupts = <0x880>;
@@ -193,9 +193,9 @@ pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0.
 		};
 	};
 
-	i2c0: i2c@0xfff20000 {
+	i2c0: i2c@fff20000 {
 		...
-		ov772x_1: camera@0x21 {
+		ov772x_1: camera@21 {
 			compatible = "ovti,ov772x";
 			reg = <0x21>;
 			vddio-supply = <&regulator1>;
@@ -219,7 +219,7 @@ pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0.
 			};
 		};
 
-		imx074: camera@0x1a {
+		imx074: camera@1a {
 			compatible = "sony,imx074";
 			reg = <0x1a>;
 			vddio-supply = <&regulator1>;
@@ -239,7 +239,7 @@ pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0.
 		};
 	};
 
-	csi2: csi2@0xffc90000 {
+	csi2: csi2@ffc90000 {
 		compatible = "renesas,sh-mobile-csi2";
 		reg = <0xffc90000 0x1000>;
 		interrupts = <0x17a0>;

Documentation/devicetree/bindings/memory-controllers/ti/emif.txt

@@ -46,7 +46,7 @@ Optional properties:
 
 Example:
 
-emif1: emif@0x4c000000 {
+emif1: emif@4c000000 {
 	compatible	= "ti,emif-4d";
 	ti,hwmods	= "emif2";
 	phy-type	= <1>;

Documentation/devicetree/bindings/mfd/ti-keystone-devctrl.txt

@@ -13,7 +13,7 @@ Required properties:
 
 Example:
 
-devctrl: device-state-control@0x02620000 {
+devctrl: device-state-control@02620000 {
 	compatible = "ti,keystone-devctrl", "syscon";
 	reg = <0x02620000 0x1000>;
 };

Documentation/devicetree/bindings/misc/brcm,kona-smc.txt

@@ -9,7 +9,7 @@ Required properties:
 - reg : Location and size of bounce buffer
 
 Example:
-	smc@0x3404c000 {
+	smc@3404c000 {
 		compatible = "brcm,bcm11351-smc", "brcm,kona-smc";
 		reg = <0x3404c000 0x400>; //1 KiB in SRAM
 	};

Documentation/devicetree/bindings/mmc/brcm,kona-sdhci.txt

@@ -12,7 +12,7 @@ Refer to clocks/clock-bindings.txt for generic clock consumer properties.
 
 Example:
 
-sdio2: sdio@0x3f1a0000 {
+sdio2: sdio@3f1a0000 {
 	compatible = "brcm,kona-sdhci";
 	reg = <0x3f1a0000 0x10000>;
 	clocks = <&sdio3_clk>;

Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt

@@ -24,7 +24,7 @@ Optional properties:
 
 Example:
 
-sdhci0: sdhci@0x18041000 {
+sdhci0: sdhci@18041000 {
 	compatible = "brcm,sdhci-iproc-cygnus";
 	reg = <0x18041000 0x100>;
 	interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;

Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt

@@ -55,7 +55,7 @@ Examples:
 
 [hwmod populated DMA resources]
 
-	mmc1: mmc@0x4809c000 {
+	mmc1: mmc@4809c000 {
 		compatible = "ti,omap4-hsmmc";
 		reg = <0x4809c000 0x400>;
 		ti,hwmods = "mmc1";
@@ -67,7 +67,7 @@ Examples:
 
 [generic DMA request binding]
 
-	mmc1: mmc@0x4809c000 {
+	mmc1: mmc@4809c000 {
 		compatible = "ti,omap4-hsmmc";
 		reg = <0x4809c000 0x400>;
 		ti,hwmods = "mmc1";

Documentation/devicetree/bindings/mtd/gpmc-nor.txt

@@ -82,15 +82,15 @@ gpmc: gpmc@6e000000 {
 			label = "bootloader-nor";
 			reg = <0 0x40000>;
 		};
-		partition@0x40000 {
+		partition@40000 {
 			label = "params-nor";
 			reg = <0x40000 0x40000>;
 		};
-		partition@0x80000 {
+		partition@80000 {
 			label = "kernel-nor";
 			reg = <0x80000 0x200000>;
 		};
-		partition@0x280000 {
+		partition@280000 {
 			label = "filesystem-nor";
 			reg = <0x240000 0x7d80000>;
 		};

Documentation/devicetree/bindings/mtd/mtk-nand.txt

@@ -131,7 +131,7 @@ Example:
 				read-only;
 				reg = <0x00000000 0x00400000>;
 			};
-			android@0x00400000 {
+			android@00400000 {
 				label = "android";
 				reg = <0x00400000 0x12c00000>;
 			};

Documentation/devicetree/bindings/net/altera_tse.txt

@@ -52,7 +52,7 @@ Optional properties:
 
 Example:
 
-	tse_sub_0_eth_tse_0: ethernet@0x1,00000000 {
+	tse_sub_0_eth_tse_0: ethernet@1,00000000 {
 		compatible = "altr,tse-msgdma-1.0";
 		reg =	<0x00000001 0x00000000 0x00000400>,
 			<0x00000001 0x00000460 0x00000020>,
@@ -90,7 +90,7 @@ Example:
 		};
 	};
 
-	tse_sub_1_eth_tse_0: ethernet@0x1,00001000 {
+	tse_sub_1_eth_tse_0: ethernet@1,00001000 {
 		compatible = "altr,tse-msgdma-1.0";
 		reg = 	<0x00000001 0x00001000 0x00000400>,
 			<0x00000001 0x00001460 0x00000020>,

Documentation/devicetree/bindings/net/mdio.txt

@@ -18,7 +18,7 @@ Example :
 This example shows these optional properties, plus other properties
 required for the TI Davinci MDIO driver.
 
-	davinci_mdio: ethernet@0x5c030000 {
+	davinci_mdio: ethernet@5c030000 {
 		compatible = "ti,davinci_mdio";
 		reg = <0x5c030000 0x1000>;
 		#address-cells = <1>;

Documentation/devicetree/bindings/net/socfpga-dwmac.txt

@@ -28,7 +28,7 @@ Required properties:
 
 Example:
 
-gmii_to_sgmii_converter: phy@0x100000240 {
+gmii_to_sgmii_converter: phy@100000240 {
 	compatible = "altr,gmii-to-sgmii-2.0";
 	reg = <0x00000001 0x00000240 0x00000008>,
 		<0x00000001 0x00000200 0x00000040>;

Documentation/devicetree/bindings/nios2/nios2.txt

@@ -36,7 +36,7 @@ Optional properties:
 
 Example:
 
-cpu@0x0 {
+cpu@0 {
 	device_type = "cpu";
 	compatible = "altr,nios2-1.0";
 	reg = <0>;

Documentation/devicetree/bindings/pci/altera-pcie.txt

@@ -25,7 +25,7 @@ Optional properties:
 - bus-range:	PCI bus numbers covered
 
 Example
-	pcie_0: pcie@0xc00000000 {
+	pcie_0: pcie@c00000000 {
 		compatible = "altr,pcie-root-port-1.0";
 		reg = <0xc0000000 0x20000000>,
 			<0xff220000 0x00004000>;

Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt

@@ -52,7 +52,7 @@ Additional required properties for imx7d-pcie:
 
 Example:
 
-	pcie@0x01000000 {
+	pcie@01000000 {
 		compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
 		reg = <0x01ffc000 0x04000>,
 		      <0x01f00000 0x80000>;

Documentation/devicetree/bindings/pci/hisilicon-pcie.txt

@@ -21,7 +21,7 @@ Optional properties:
 - dma-coherent: Present if DMA operations are coherent.
 
 Hip05 Example (note that Hip06 is the same except compatible):
-	pcie@0xb0080000 {
+	pcie@b0080000 {
 		compatible = "hisilicon,hip05-pcie", "snps,dw-pcie";
 		reg = <0 0xb0080000 0 0x10000>, <0x220 0x00000000 0 0x2000>;
 		reg-names = "rc_dbi", "config";

Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt

@@ -45,7 +45,7 @@ Optional properties:
 - usb3_vbus-supply : regulator phandle for controller usb3 vbus
 
 Example:
-	usbphy: phy@0x01c13400 {
+	usbphy: phy@01c13400 {
 		#phy-cells = <1>;
 		compatible = "allwinner,sun4i-a10-usb-phy";
 		/* phy base regs, phy1 pmu reg, phy2 pmu reg */

Documentation/devicetree/bindings/pinctrl/brcm,cygnus-pinmux.txt

@@ -25,7 +25,7 @@ Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
 
 For example:
 
-	pinmux: pinmux@0x0301d0c8 {
+	pinmux: pinmux@0301d0c8 {
 		compatible = "brcm,cygnus-pinmux";
 		reg = <0x0301d0c8 0x1b0>;
 

Documentation/devicetree/bindings/pinctrl/pinctrl-atlas7.txt

@@ -96,14 +96,14 @@ For example, pinctrl might have subnodes like the following:
 
 For a specific board, if it wants to use sd1,
 it can add the following to its board-specific .dts file.
-sd1: sd@0x12340000 {
+sd1: sd@12340000 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&sd1_pmx0>;
 }
 
 or
 
-sd1: sd@0x12340000 {
+sd1: sd@12340000 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&sd1_pmx1>;
 }

Documentation/devicetree/bindings/pinctrl/pinctrl-sirf.txt

@@ -41,7 +41,7 @@ For example, pinctrl might have subnodes like the following:
 
 For a specific board, if it wants to use uart2 without hardware flow control,
 it can add the following to its board-specific .dts file.
-uart2: uart@0xb0070000 {
+uart2: uart@b0070000 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart2_noflow_pins_a>;
 }

Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt

@@ -136,7 +136,7 @@ Example for rk3188:
 		#size-cells = <1>;
 		ranges;
 
-		gpio0: gpio0@0x2000a000 {
+		gpio0: gpio0@2000a000 {
 			compatible = "rockchip,rk3188-gpio-bank0";
 			reg = <0x2000a000 0x100>;
 			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
@@ -149,7 +149,7 @@ Example for rk3188:
 			#interrupt-cells = <2>;
 		};
 
-		gpio1: gpio1@0x2003c000 {
+		gpio1: gpio1@2003c000 {
 			compatible = "rockchip,gpio-bank";
 			reg = <0x2003c000 0x100>;
 			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;

Documentation/devicetree/bindings/regulator/regulator.txt

@@ -107,7 +107,7 @@ regulators (twl_reg1 and twl_reg2),
 		...
 	};
 
-	mmc: mmc@0x0 {
+	mmc: mmc@0 {
 		...
 		...
 		vmmc-supply = <&twl_reg1>;

Documentation/devicetree/bindings/serial/efm32-uart.txt

@@ -12,7 +12,7 @@ Optional properties:
 
 Example:
 
-uart@0x4000c400 {
+uart@4000c400 {
 	compatible = "energymicro,efm32-uart";
 	reg = <0x4000c400 0x400>;
 	interrupts = <15>;

Documentation/devicetree/bindings/serio/allwinner,sun4i-ps2.txt

@@ -14,7 +14,7 @@ Required properties:
 
 
 Example:
-	ps20: ps2@0x01c2a000 {
+	ps20: ps2@01c2a000 {
 		compatible = "allwinner,sun4i-a10-ps2";
 		reg = <0x01c2a000 0x400>;
 		interrupts = <0 62 4>;

Documentation/devicetree/bindings/soc/ti/keystone-navigator-qmss.txt

@@ -220,7 +220,7 @@ qmss: qmss@2a40000 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;
-		pdsp0@0x2a10000 {
+		pdsp0@2a10000 {
 			reg = <0x2a10000 0x1000>,
 			      <0x2a0f000 0x100>,
 			      <0x2a0c000 0x3c8>,

Documentation/devicetree/bindings/sound/adi,axi-i2s.txt

@@ -21,7 +21,7 @@ please check:
 
 Example:
 
-	i2s: i2s@0x77600000 {
+	i2s: i2s@77600000 {
 		compatible = "adi,axi-i2s-1.00.a";
 		reg = <0x77600000 0x1000>;
 		clocks = <&clk 15>, <&audio_clock>;

Documentation/devicetree/bindings/sound/adi,axi-spdif-tx.txt

@@ -20,7 +20,7 @@ please check:
 
 Example:
 
-	spdif: spdif@0x77400000 {
+	spdif: spdif@77400000 {
 		compatible = "adi,axi-spdif-tx-1.00.a";
 		reg = <0x77600000 0x1000>;
 		clocks = <&clk 15>, <&audio_clock>;

Documentation/devicetree/bindings/sound/ak4613.txt

@@ -20,7 +20,7 @@ Optional properties:
 Example:
 
 &i2c {
-	ak4613: ak4613@0x10 {
+	ak4613: ak4613@10 {
 		compatible = "asahi-kasei,ak4613";
 		reg = <0x10>;
 	};

Documentation/devicetree/bindings/sound/ak4642.txt

@@ -17,7 +17,7 @@ Optional properties:
 Example 1:
 
 &i2c {
-	ak4648: ak4648@0x12 {
+	ak4648: ak4648@12 {
 		compatible = "asahi-kasei,ak4642";
 		reg = <0x12>;
 	};

Documentation/devicetree/bindings/sound/max98371.txt

@@ -10,7 +10,7 @@ Required properties:
 Example:
 
 &i2c {
-	max98371: max98371@0x31 {
+	max98371: max98371@31 {
 		compatible = "maxim,max98371";
 		reg = <0x31>;
 	};

Documentation/devicetree/bindings/sound/max9867.txt

@@ -10,7 +10,7 @@ Required properties:
 Example:
 
 &i2c {
-	max9867: max9867@0x18 {
+	max9867: max9867@18 {
 		compatible = "maxim,max9867";
 		reg = <0x18>;
 	};

Documentation/devicetree/bindings/sound/renesas,fsi.txt

@@ -20,7 +20,7 @@ Required properties:
 
 Example:
 
-sh_fsi2: sh_fsi2@0xec230000 {
+sh_fsi2: sh_fsi2@ec230000 {
 	compatible = "renesas,sh_fsi2";
 	reg = <0xec230000 0x400>;
 	interrupts = <0 146 0x4>;

Documentation/devicetree/bindings/sound/rockchip-spdif.txt

@@ -33,7 +33,7 @@ Required properties on RK3288:
 
 Example for the rk3188 SPDIF controller:
 
-spdif: spdif@0x1011e000 {
+spdif: spdif@1011e000 {
 	compatible = "rockchip,rk3188-spdif", "rockchip,rk3066-spdif";
 	reg = <0x1011e000 0x2000>;
 	interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;

Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt

@@ -51,7 +51,7 @@ Optional properties:
 
 Example:
 
-	sti_uni_player1: sti-uni-player@0x8D81000 {
+	sti_uni_player1: sti-uni-player@8D81000 {
 		compatible = "st,stih407-uni-player-hdmi";
 		#sound-dai-cells = <0>;
 		st,syscfg = <&syscfg_core>;
@@ -63,7 +63,7 @@ Example:
 		st,tdm-mode = <1>;
 	};
 
-	sti_uni_player2: sti-uni-player@0x8D82000 {
+	sti_uni_player2: sti-uni-player@8D82000 {
 		compatible = "st,stih407-uni-player-pcm-out";
 		#sound-dai-cells = <0>;
 		st,syscfg = <&syscfg_core>;
@@ -74,7 +74,7 @@ Example:
 		dma-names = "tx";
 	};
 
-	sti_uni_player3: sti-uni-player@0x8D85000 {
+	sti_uni_player3: sti-uni-player@8D85000 {
 		compatible = "st,stih407-uni-player-spdif";
 		#sound-dai-cells = <0>;
 		st,syscfg = <&syscfg_core>;
@@ -85,7 +85,7 @@ Example:
 		dma-names = "tx";
 	};
 
-	sti_uni_reader1: sti-uni-reader@0x8D84000 {
+	sti_uni_reader1: sti-uni-reader@8D84000 {
 		compatible = "st,stih407-uni-reader-hdmi";
 		#sound-dai-cells = <0>;
 		st,syscfg = <&syscfg_core>;

Documentation/devicetree/bindings/spi/efm32-spi.txt

@@ -19,7 +19,7 @@ Recommended properties :
 
 Example:
 
-spi1: spi@0x4000c400 { /* USART1 */
+spi1: spi@4000c400 { /* USART1 */
 	#address-cells = <1>;
 	#size-cells = <0>;
 	compatible = "energymicro,efm32-spi";

Documentation/devicetree/bindings/thermal/thermal.txt

@@ -239,7 +239,7 @@ cpus {
 	 * A simple fan controller which supports 10 speeds of operation
 	 * (represented as 0-9).
 	 */
-	fan0: fan@0x48 {
+	fan0: fan@48 {
 		...
 		cooling-min-level = <0>;
 		cooling-max-level = <9>;
@@ -252,7 +252,7 @@ ocp {
 	/*
 	 * A simple IC with a single bandgap temperature sensor.
 	 */
-	bandgap0: bandgap@0x0000ED00 {
+	bandgap0: bandgap@0000ED00 {
 		...
 		#thermal-sensor-cells = <0>;
 	};
@@ -330,7 +330,7 @@ ocp {
 	/*
 	 * A simple IC with several bandgap temperature sensors.
 	 */
-	bandgap0: bandgap@0x0000ED00 {
+	bandgap0: bandgap@0000ED00 {
 		...
 		#thermal-sensor-cells = <1>;
 	};
@@ -447,7 +447,7 @@ one thermal zone.
 	/*
 	 * A simple IC with a single temperature sensor.
 	 */
-	adc: sensor@0x49 {
+	adc: sensor@49 {
 		...
 		#thermal-sensor-cells = <0>;
 	};
@@ -458,7 +458,7 @@ ocp {
 	/*
 	 * A simple IC with a single bandgap temperature sensor.
 	 */
-	bandgap0: bandgap@0x0000ED00 {
+	bandgap0: bandgap@0000ED00 {
 		...
 		#thermal-sensor-cells = <0>;
 	};
@@ -516,7 +516,7 @@ with many sensors and many cooling devices.
 	/*
 	 * An IC with several temperature sensor.
 	 */
-	adc_dummy: sensor@0x50 {
+	adc_dummy: sensor@50 {
 		...
 		#thermal-sensor-cells = <1>; /* sensor internal ID */
 	};

Documentation/devicetree/bindings/ufs/ufs-qcom.txt

@@ -32,7 +32,7 @@ Optional properties:
 
 Example:
 
-	ufsphy1: ufsphy@0xfc597000 {
+	ufsphy1: ufsphy@fc597000 {
 		compatible = "qcom,ufs-phy-qmp-20nm";
 		reg = <0xfc597000 0x800>;
 		reg-names = "phy_mem";
@@ -53,7 +53,7 @@ Example:
 			<&clock_gcc clk_gcc_ufs_rx_cfg_clk>;
 	};
 
-	ufshc@0xfc598000 {
+	ufshc@fc598000 {
 		...
 		phys = <&ufsphy1>;
 		phy-names = "ufsphy";

Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt

@@ -46,7 +46,7 @@ Note: If above properties are not defined it can be assumed that the supply
 regulators or clocks are always on.
 
 Example:
-	ufshc@0xfc598000 {
+	ufshc@fc598000 {
 		compatible = "jedec,ufs-1.1";
 		reg = <0xfc598000 0x800>;
 		interrupts = <0 28 0>;

Documentation/devicetree/bindings/usb/am33xx-usb.txt

@@ -95,6 +95,7 @@ usb: usb@47400000 {
 		reg = <0x47401300 0x100>;
 		reg-names = "phy";
 		ti,ctrl_mod = <&ctrl_mod>;
+		#phy-cells = <0>;
 	};
 
 	usb0: usb@47401000 {
@@ -141,6 +142,7 @@ usb: usb@47400000 {
 		reg = <0x47401b00 0x100>;
 		reg-names = "phy";
 		ti,ctrl_mod = <&ctrl_mod>;
+		#phy-cells = <0>;
 	};
 
 	usb1: usb@47401800 {

Documentation/devicetree/bindings/usb/ehci-st.txt

@@ -22,7 +22,7 @@ See: Documentation/devicetree/bindings/reset/reset.txt
 
 Example:
 
-	ehci1: usb@0xfe203e00 {
+	ehci1: usb@fe203e00 {
 		compatible = "st,st-ehci-300x";
 		reg = <0xfe203e00 0x100>;
 		interrupts = <GIC_SPI 148 IRQ_TYPE_NONE>;

Documentation/devicetree/bindings/usb/ohci-st.txt

@@ -20,7 +20,7 @@ See: Documentation/devicetree/bindings/reset/reset.txt
 
 Example:
 
-	ohci0: usb@0xfe1ffc00 {
+	ohci0: usb@fe1ffc00 {
 		compatible = "st,st-ohci-300x";
 		reg = <0xfe1ffc00 0x100>;
 		interrupts = <GIC_SPI 149 IRQ_TYPE_NONE>;

Documentation/devicetree/bindings/watchdog/ingenic,jz4740-wdt.txt

@@ -6,7 +6,7 @@ reg: Register address and length for watchdog registers
 
 Example:
 
-watchdog: jz4740-watchdog@0x10002000 {
+watchdog: jz4740-watchdog@10002000 {
 	compatible = "ingenic,jz4740-watchdog";
 	reg = <0x10002000 0x100>;
 };

Documentation/media/dvb-drivers/frontends.rst

@@ -0,0 +1,30 @@
+****************
+Frontend drivers
+****************
+
+Frontend attach headers
+***********************
+
+.. Keep it on alphabetic order
+
+.. kernel-doc:: drivers/media/dvb-frontends/a8293.h
+.. kernel-doc:: drivers/media/dvb-frontends/af9013.h
+.. kernel-doc:: drivers/media/dvb-frontends/ascot2e.h
+.. kernel-doc:: drivers/media/dvb-frontends/cxd2820r.h
+.. kernel-doc:: drivers/media/dvb-frontends/drxk.h
+.. kernel-doc:: drivers/media/dvb-frontends/dvb-pll.h
+.. kernel-doc:: drivers/media/dvb-frontends/helene.h
+.. kernel-doc:: drivers/media/dvb-frontends/horus3a.h
+.. kernel-doc:: drivers/media/dvb-frontends/ix2505v.h
+.. kernel-doc:: drivers/media/dvb-frontends/m88ds3103.h
+.. kernel-doc:: drivers/media/dvb-frontends/mb86a20s.h
+.. kernel-doc:: drivers/media/dvb-frontends/mn88472.h
+.. kernel-doc:: drivers/media/dvb-frontends/rtl2830.h
+.. kernel-doc:: drivers/media/dvb-frontends/rtl2832.h
+.. kernel-doc:: drivers/media/dvb-frontends/rtl2832_sdr.h
+.. kernel-doc:: drivers/media/dvb-frontends/stb6000.h
+.. kernel-doc:: drivers/media/dvb-frontends/tda10071.h
+.. kernel-doc:: drivers/media/dvb-frontends/tda826x.h
+.. kernel-doc:: drivers/media/dvb-frontends/zd1301_demod.h
+.. kernel-doc:: drivers/media/dvb-frontends/zl10036.h
+

Documentation/media/dvb-drivers/index.rst

@@ -41,4 +41,5 @@ For more details see the file COPYING in the source distribution of Linux.
 	technisat
 	ttusb-dec
 	udev
+	frontends
 	contributors

Documentation/virtual/kvm/api.txt

@@ -2901,14 +2901,19 @@ userspace buffer and its length:
 
 struct kvm_s390_irq_state {
 	__u64 buf;
-	__u32 flags;
+	__u32 flags;        /* will stay unused for compatibility reasons */
 	__u32 len;
-	__u32 reserved[4];
+	__u32 reserved[4];  /* will stay unused for compatibility reasons */
 };
 
 Userspace passes in the above struct and for each pending interrupt a
 struct kvm_s390_irq is copied to the provided buffer.
 
+The structure contains a flags and a reserved field for future extensions. As
+the kernel never checked for flags == 0 and QEMU never pre-zeroed flags and
+reserved, these fields can not be used in the future without breaking
+compatibility.
+
 If -ENOBUFS is returned the buffer provided was too small and userspace
 may retry with a bigger buffer.
 
@@ -2932,10 +2937,14 @@ containing a struct kvm_s390_irq_state:
 
 struct kvm_s390_irq_state {
 	__u64 buf;
+	__u32 flags;        /* will stay unused for compatibility reasons */
 	__u32 len;
-	__u32 pad;
+	__u32 reserved[4];  /* will stay unused for compatibility reasons */
 };
 
+The restrictions for flags and reserved apply as well.
+(see KVM_S390_GET_IRQ_STATE)
+
 The userspace memory referenced by buf contains a struct kvm_s390_irq
 for each interrupt to be injected into the guest.
 If one of the interrupts could not be injected for some reason the

MAINTAINERS

@@ -859,7 +859,8 @@ F:	kernel/configs/android*
 ANDROID DRIVERS
 M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 M:	Arve Hjønnevåg <arve@android.com>
-M:	Riley Andrews <riandrews@android.com>
+M:	Todd Kjos <tkjos@android.com>
+M:	Martijn Coenen <maco@android.com>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging.git
 L:	devel@driverdev.osuosl.org
 S:	Supported
@@ -2046,7 +2047,7 @@ F:	arch/arm/boot/dts/uniphier*
 F:	arch/arm/include/asm/hardware/cache-uniphier.h
 F:	arch/arm/mach-uniphier/
 F:	arch/arm/mm/cache-uniphier.c
-F:	arch/arm64/boot/dts/socionext/
+F:	arch/arm64/boot/dts/socionext/uniphier*
 F:	drivers/bus/uniphier-system-bus.c
 F:	drivers/clk/uniphier/
 F:	drivers/gpio/gpio-uniphier.c
@@ -7766,6 +7767,7 @@ F:	security/keys/
 
 KGDB / KDB /debug_core
 M:	Jason Wessel <jason.wessel@windriver.com>
+M:	Daniel Thompson <daniel.thompson@linaro.org>
 W:	http://kgdb.wiki.kernel.org/
 L:	kgdb-bugreport@lists.sourceforge.net
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb.git
@@ -12641,6 +12643,14 @@ S:	Maintained
 F:	drivers/ssb/
 F:	include/linux/ssb/
 
+SONY IMX274 SENSOR DRIVER
+M:	Leon Luo <leonl@leopardimaging.com>
+L:	linux-media@vger.kernel.org
+T:	git git://linuxtv.org/media_tree.git
+S:	Maintained
+F:	drivers/media/i2c/imx274.c
+F:	Documentation/devicetree/bindings/media/i2c/imx274.txt
+
 SONY MEMORYSTICK CARD SUPPORT
 M:	Alex Dubov <oakad@yahoo.com>
 W:	http://tifmxx.berlios.de/

Makefile

@@ -2,7 +2,7 @@
 VERSION = 4
 PATCHLEVEL = 15
 SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc3
 NAME = Fearless Coyote
 
 # *DOCUMENTATION*

arch/alpha/include/uapi/asm/Kbuild

@@ -1,2 +1,4 @@
 # UAPI Header export list
 include include/uapi/asm-generic/Kbuild.asm
+
+generic-y += bpf_perf_event.h

arch/arc/include/uapi/asm/Kbuild

@@ -3,6 +3,7 @@ include include/uapi/asm-generic/Kbuild.asm
 
 generic-y += auxvec.h
 generic-y += bitsperlong.h
+generic-y += bpf_perf_event.h
 generic-y += errno.h
 generic-y += fcntl.h
 generic-y += ioctl.h

arch/arm/boot/dts/am33xx.dtsi

@@ -630,6 +630,7 @@
 				reg-names = "phy";
 				status = "disabled";
 				ti,ctrl_mod = <&usb_ctrl_mod>;
+				#phy-cells = <0>;
 			};
 
 			usb0: usb@47401000 {
@@ -678,6 +679,7 @@
 				reg-names = "phy";
 				status = "disabled";
 				ti,ctrl_mod = <&usb_ctrl_mod>;
+				#phy-cells = <0>;
 			};
 
 			usb1: usb@47401800 {

arch/arm/boot/dts/am4372.dtsi

@@ -927,7 +927,8 @@
 			reg = <0x48038000 0x2000>,
 			      <0x46000000 0x400000>;
 			reg-names = "mpu", "dat";
-			interrupts = <80>, <81>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "tx", "rx";
 			status = "disabled";
 			dmas = <&edma 8 2>,
@@ -941,7 +942,8 @@
 			reg = <0x4803C000 0x2000>,
 			      <0x46400000 0x400000>;
 			reg-names = "mpu", "dat";
-			interrupts = <82>, <83>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "tx", "rx";
 			status = "disabled";
 			dmas = <&edma 10 2>,

arch/arm/boot/dts/am437x-cm-t43.dts

@@ -301,8 +301,8 @@
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0_pins>;
-	dmas = <&edma 16
-		&edma 17>;
+	dmas = <&edma 16 0
+		&edma 17 0>;
 	dma-names = "tx0", "rx0";
 
 	flash: w25q64cvzpig@0 {

arch/arm/boot/dts/armada-385-db-ap.dts

@@ -236,6 +236,7 @@
 	usb3_phy: usb3_phy {
 		compatible = "usb-nop-xceiv";
 		vcc-supply = <&reg_xhci0_vbus>;
+		#phy-cells = <0>;
 	};
 
 	reg_xhci0_vbus: xhci0-vbus {

arch/arm/boot/dts/armada-385-linksys.dtsi

@@ -66,6 +66,7 @@
 	usb3_1_phy: usb3_1-phy {
 		compatible = "usb-nop-xceiv";
 		vcc-supply = <&usb3_1_vbus>;
+		#phy-cells = <0>;
 	};
 
 	usb3_1_vbus: usb3_1-vbus {

arch/arm/boot/dts/armada-385-synology-ds116.dts

@@ -191,11 +191,13 @@
 	usb3_0_phy: usb3_0_phy {
 		compatible = "usb-nop-xceiv";
 		vcc-supply = <&reg_usb3_0_vbus>;
+		#phy-cells = <0>;
 	};
 
 	usb3_1_phy: usb3_1_phy {
 		compatible = "usb-nop-xceiv";
 		vcc-supply = <&reg_usb3_1_vbus>;
+		#phy-cells = <0>;
 	};
 
 	reg_usb3_0_vbus: usb3-vbus0 {

arch/arm/boot/dts/armada-388-gp.dts

@@ -276,11 +276,13 @@
 	usb2_1_phy: usb2_1_phy {
 		compatible = "usb-nop-xceiv";
 		vcc-supply = <&reg_usb2_1_vbus>;
+		#phy-cells = <0>;
 	};
 
 	usb3_phy: usb3_phy {
 		compatible = "usb-nop-xceiv";
 		vcc-supply = <&reg_usb3_vbus>;
+		#phy-cells = <0>;
 	};
 
 	reg_usb3_vbus: usb3-vbus {

arch/arm/boot/dts/bcm-nsp.dtsi

@@ -85,7 +85,7 @@
 		timer@20200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x20200 0x100>;
-			interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
 			clocks = <&periph_clk>;
 		};
 
@@ -93,7 +93,7 @@
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x20600 0x20>;
 			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) |
-						  IRQ_TYPE_LEVEL_HIGH)>;
+						  IRQ_TYPE_EDGE_RISING)>;
 			clocks = <&periph_clk>;
 		};
 

arch/arm/boot/dts/bcm283x.dtsi

@@ -639,5 +639,6 @@
 
 	usbphy: phy {
 		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
 	};
 };

arch/arm/boot/dts/bcm958623hr.dts

@@ -141,10 +141,6 @@
 	status = "okay";
 };
 
-&sata {
-	status = "okay";
-};
-
 &qspi {
 	bspi-sel = <0>;
 	flash: m25p80@0 {

arch/arm/boot/dts/bcm958625hr.dts

@@ -177,10 +177,6 @@
 	status = "okay";
 };
 
-&sata {
-	status = "okay";
-};
-
 &srab {
 	compatible = "brcm,bcm58625-srab", "brcm,nsp-srab";
 	status = "okay";

arch/arm/boot/dts/dm814x.dtsi

@@ -75,6 +75,7 @@
 				reg = <0x47401300 0x100>;
 				reg-names = "phy";
 				ti,ctrl_mod = <&usb_ctrl_mod>;
+				#phy-cells = <0>;
 			};
 
 			usb0: usb@47401000 {
@@ -385,6 +386,7 @@
 					reg = <0x1b00 0x100>;
 					reg-names = "phy";
 					ti,ctrl_mod = <&usb_ctrl_mod>;
+					#phy-cells = <0>;
 				};
 			};
 

arch/arm/boot/dts/imx53.dtsi

@@ -433,15 +433,6 @@
 				clock-names = "ipg", "per";
 			};
 
-			srtc: srtc@53fa4000 {
-				compatible = "fsl,imx53-rtc", "fsl,imx25-rtc";
-				reg = <0x53fa4000 0x4000>;
-				interrupts = <24>;
-				interrupt-parent = <&tzic>;
-				clocks = <&clks IMX5_CLK_SRTC_GATE>;
-				clock-names = "ipg";
-			};
-
 			iomuxc: iomuxc@53fa8000 {
 				compatible = "fsl,imx53-iomuxc";
 				reg = <0x53fa8000 0x4000>;

arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts

@@ -72,7 +72,8 @@
 };
 
 &gpmc {
-	ranges = <1 0 0x08000000 0x1000000>;	/* CS1: 16MB for LAN9221 */
+	ranges = <0 0 0x30000000 0x1000000	/* CS0: 16MB for NAND */
+		  1 0 0x2c000000 0x1000000>;	/* CS1: 16MB for LAN9221 */
 
 	ethernet@gpmc {
 		pinctrl-names = "default";

arch/arm/boot/dts/logicpd-som-lv.dtsi

@@ -33,11 +33,12 @@
 	hsusb2_phy: hsusb2_phy {
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
+		#phy-cells = <0>;
 	};
 };
 
 &gpmc {
-	ranges = <0 0 0x00000000 0x1000000>;	/* CS0: 16MB for NAND */
+	ranges = <0 0 0x30000000 0x1000000>;	/* CS0: 16MB for NAND */
 
 	nand@0,0 {
 		compatible = "ti,omap2-nand";
@@ -121,7 +122,7 @@
 
 &mmc3 {
 	interrupts-extended = <&intc 94 &omap3_pmx_core2 0x46>;
-	pinctrl-0 = <&mmc3_pins>;
+	pinctrl-0 = <&mmc3_pins &wl127x_gpio>;
 	pinctrl-names = "default";
 	vmmc-supply = <&wl12xx_vmmc>;
 	non-removable;
@@ -132,8 +133,8 @@
 	wlcore: wlcore@2 {
 		compatible = "ti,wl1273";
 		reg = <2>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <24 IRQ_TYPE_LEVEL_HIGH>; /* gpio 152 */
+		interrupt-parent = <&gpio1>;
+		interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; /* gpio 2 */
 		ref-clock-frequency = <26000000>;
 	};
 };
@@ -157,8 +158,6 @@
 			OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat5.sdmmc3_dat1 */
 			OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat2 */
 			OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3)	/* sdmmc2_dat6.sdmmc3_dat3 */
-			OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4)	/* mcbsp4_clkx.gpio_152 */
-			OMAP3_CORE1_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)	/* sys_boot1.gpio_3 */
 			OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
 			OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3)	/* mcspi1_cs2.sdmmc_clk */
 		>;
@@ -228,6 +227,12 @@
 			OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4)	/* sys_boot2.gpio_4 */
 		>;
 	};
+	wl127x_gpio: pinmux_wl127x_gpio_pin {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a0c, PIN_INPUT | MUX_MODE4)		/* sys_boot0.gpio_2 */
+			OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)	/* sys_boot1.gpio_3 */
+		>;
+	};
 };
 
 &omap3_pmx_core2 {

arch/arm/boot/dts/meson.dtsi

@@ -85,15 +85,6 @@
 				reg = <0x7c00 0x200>;
 			};
 
-			gpio_intc: interrupt-controller@9880 {
-				compatible = "amlogic,meson-gpio-intc";
-				reg = <0xc1109880 0x10>;
-				interrupt-controller;
-				#interrupt-cells = <2>;
-				amlogic,channel-interrupts = <64 65 66 67 68 69 70 71>;
-				status = "disabled";
-			};
-
 			hwrng: rng@8100 {
 				compatible = "amlogic,meson-rng";
 				reg = <0x8100 0x8>;
@@ -191,6 +182,15 @@
 				status = "disabled";
 			};
 
+			gpio_intc: interrupt-controller@9880 {
+				compatible = "amlogic,meson-gpio-intc";
+				reg = <0x9880 0x10>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				amlogic,channel-interrupts = <64 65 66 67 68 69 70 71>;
+				status = "disabled";
+			};
+
 			wdt: watchdog@9900 {
 				compatible = "amlogic,meson6-wdt";
 				reg = <0x9900 0x8>;

arch/arm/boot/dts/nspire.dtsi

@@ -56,6 +56,7 @@
 
 	usb_phy: usb_phy {
 		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
 	};
 
 	vbus_reg: vbus_reg {

arch/arm/boot/dts/omap3-beagle-xm.dts

@@ -90,6 +90,7 @@
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; /* gpio_147 */
 		vcc-supply = <&hsusb2_power>;
+		#phy-cells = <0>;
 	};
 
 	tfp410: encoder0 {