Merge tag 'mvebu-soc-orion5x-3.16' of git://git.infradead.org/linux-mvebu into next/soc

Merge "ARM: mvebu: SoC orion5x DT conversion for v3.16" from Jason Cooper:

mvebu SoC orion5x DT conversion for v3.16

 - orion5x
    - convert to DT

* tag 'mvebu-soc-orion5x-3.16' of git://git.infradead.org/linux-mvebu: (29 commits)
  ARM: orion: remove no longer needed gpio DT code
  ARM: orion: remove no longer needed DT IRQ code
  ARM: orion5x: convert Maxtor Shared Storage II to the Device Tree
  ARM: orion5x: convert d2net to Device Tree
  ARM: orion5x: convert RD-88F5182 to Device Tree
  ARM: orion5x: remove unneeded code for edmini_v2
  ARM: orion5x: keep TODO list in edmini_v2 DT
  ARM: orion5x: use DT to describe NOR on edmini_v2
  ARM: orion5x: use DT to describe EHCI on edmini_v2
  ARM: orion5x: use DT to describe I2C devices on edmini_v2
  ARM: orion5x: convert edmini_v2 to DT pinctrl
  ARM: orion5x: add standard pinctrl configs for sata0 and sata1
  ARM: orion5x: add Device Bus description at SoC level
  ARM: orion5x: update I2C description at SoC level
  ARM: orion5x: enable pinctrl driver at SoC level
  ARM: orion5x: switch to DT interrupts and timer
  ARM: orion: switch to a per-platform handle_irq() function
  ARM: orion5x: convert to use 'clocks' property for UART controllers
  ARM: orion5x: switch to use the clock driver for DT platforms
  ARM: orion5x: add interrupt for Ethernet in Device Tree
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/Makefile

@@ -289,7 +289,10 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	am43x-epos-evm.dtb \
 	am437x-gp-evm.dtb \
 	dra7-evm.dtb
-dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
+dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-d2-network.dtb \
+	orion5x-lacie-ethernet-disk-mini-v2.dtb \
+	orion5x-maxtor-shared-storage-2.dtb \
+	orion5x-rd88f5182-nas.dtb
 dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
 dtb-$(CONFIG_ARCH_QCOM) += qcom-msm8660-surf.dtb \
 	qcom-msm8960-cdp.dtb \

arch/arm/boot/dts/orion5x-lacie-d2-network.dts

@@ -0,0 +1,236 @@
+/*
+ * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "orion5x-mv88f5182.dtsi"
+
+/ {
+	model = "LaCie d2 Network";
+	compatible = "lacie,d2-network", "marvell,orion5x-88f5182", "marvell,orion5x";
+
+	memory {
+		reg = <0x00000000 0x4000000>; /* 64 MB */
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		linux,stdout-path = &uart0;
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>,
+			 <MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>,
+			 <MBUS_ID(0x01, 0x0f) 0 0xfff80000 0x80000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&pmx_buttons>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		front_button {
+			label = "Front Push Button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_rocker_sw_on {
+			label = "Power rocker switch (on|auto)";
+			linux,input-type = <5>; /* EV_SW */
+			linux,code = <1>; /* D2NET_SWITCH_POWER_ON */
+			gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		power_rocker_sw_off {
+			label = "Power rocker switch (auto|off)";
+			linux,input-type = <5>; /* EV_SW */
+			linux,code = <2>; /* D2NET_SWITCH_POWER_OFF */
+			gpios = <&gpio0 9 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-0 = <&pmx_sata0_power &pmx_sata1_power>;
+		pinctrl-names = "default";
+
+		sata0_power: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "SATA0 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 3 GPIO_ACTIVE_HIGH>;
+		};
+
+		sata1_power: regulator@1 {
+			compatible = "regulator-fixed";
+			reg = <1>;
+			regulator-name = "SATA1 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&devbus_bootcs {
+	status = "okay";
+
+	devbus,keep-config;
+
+	/*
+	 * Currently the MTD code does not recognize the MX29LV400CBCT
+	 * as a bottom-type device. This could cause risks of
+	 * accidentally erasing critical flash sectors. We thus define
+	 * a single, write-protected partition covering the whole
+	 * flash.  TODO: once the flash part TOP/BOTTOM detection
+	 * issue is sorted out in the MTD code, break this into at
+	 * least three partitions: 'u-boot code', 'u-boot environment'
+	 * and 'whatever is left'.
+	 */
+	flash@0 {
+		compatible = "cfi-flash";
+		reg = <0 0x80000>;
+		bank-width = <1>;
+                #address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "Full512Kb";
+			reg = <0 0x80000>;
+			read-only;
+		};
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy: ethernet-phy {
+		reg = <8>;
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	ethernet-port@0 {
+		phy-handle = <&ethphy>;
+	};
+};
+
+&i2c {
+	status = "okay";
+	clock-frequency = <100000>;
+	#address-cells = <1>;
+
+	rtc@32 {
+		compatible = "ricoh,rs5c372b";
+		reg = <0x32>;
+	};
+
+	fan@3e {
+		compatible = "gmt,g762";
+		reg = <0x3e>;
+
+		/* Not enough HW info */
+		status = "disabled";
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c08";
+		reg = <0x50>;
+	};
+};
+
+&pinctrl {
+	pinctrl-0 = <&pmx_leds &pmx_board_id &pmx_fan_fail>;
+	pinctrl-names = "default";
+
+	pmx_board_id: pmx-board-id {
+		marvell,pins = "mpp0", "mpp1", "mpp2";
+		marvell,function = "gpio";
+	};
+
+	pmx_buttons: pmx-buttons {
+		marvell,pins = "mpp8", "mpp9", "mpp18";
+		marvell,function = "gpio";
+	};
+
+	pmx_fan_fail: pmx-fan-fail {
+		marvell,pins = "mpp5";
+		marvell,function = "gpio";
+	};
+
+	/*
+	 * MPP6: Red front LED
+	 * MPP16: Blue front LED blink control
+	 */
+	pmx_leds: pmx-leds {
+		marvell,pins = "mpp6", "mpp16";
+		marvell,function = "gpio";
+	};
+
+	pmx_sata0_led_active: pmx-sata0-led-active {
+		marvell,pins = "mpp14";
+		marvell,function = "sata0";
+	};
+
+	pmx_sata0_power: pmx-sata0-power {
+		marvell,pins = "mpp3";
+		marvell,function = "gpio";
+	};
+
+	pmx_sata1_led_active: pmx-sata1-led-active {
+		marvell,pins = "mpp15";
+		marvell,function = "sata1";
+	};
+
+	pmx_sata1_power: pmx-sata1-power {
+		marvell,pins = "mpp12";
+		marvell,function = "gpio";
+	};
+
+	/*
+	 * Non MPP GPIOs:
+	 *  GPIO 22: USB port 1 fuse (0 = Fail, 1 = Ok)
+	 *  GPIO 23: Blue front LED off
+	 *  GPIO 24: Inhibit board power off (0 = Disabled, 1 = Enabled)
+	 */
+};
+
+&sata {
+	pinctrl-0 = <&pmx_sata0_led_active
+		     &pmx_sata1_led_active>;
+	pinctrl-names = "default";
+	status = "okay";
+	nr-ports = <2>;
+};
+
+&uart0 {
+	status = "okay";
+};

arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts

@@ -6,8 +6,19 @@
  * warranty of any kind, whether express or implied.
  */
 
+/*
+ * TODO: add Orion USB device port init when kernel.org support is added.
+ * TODO: add flash write support: see below.
+ * TODO: add power-off support.
+ * TODO: add I2C EEPROM support.
+ */
+
 /dts-v1/;
-/include/ "orion5x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "orion5x-mv88f5182.dtsi"
 
 / {
 	model = "LaCie Ethernet Disk mini V2";
@@ -19,49 +30,84 @@
 
 	chosen {
 		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		linux,stdout-path = &uart0;
 	};
 
-	ocp@f1000000 {
-		serial@12000 {
-			clock-frequency = <166666667>;
-			status = "okay";
-		};
-
-		sata@80000 {
-			status = "okay";
-			nr-ports = <2>;
-		};
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>,
+			 <MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>,
+			 <MBUS_ID(0x01, 0x0f) 0 0xfff80000 0x80000>;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
+		pinctrl-0 = <&pmx_power_button>;
+		pinctrl-names = "default";
 		#address-cells = <1>;
 		#size-cells = <0>;
 		button@1 {
 			label = "Power-on Switch";
-			linux,code = <116>; /* KEY_POWER */
-			gpios = <&gpio0 18 0>;
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
 		};
 	};
 
-	gpio_leds {
+	gpio-leds {
 		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_power_led>;
+		pinctrl-names = "default";
 
 		led@1 {
 			label = "power:blue";
-			gpios = <&gpio0 16 1>;
+			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
 		};
 	};
 };
 
-&mdio {
+&devbus_bootcs {
 	status = "okay";
 
-	ethphy: ethernet-phy {
-		reg = <8>;
+	/* Read parameters */
+	devbus,bus-width    = <8>;
+	devbus,turn-off-ps  = <90000>;
+	devbus,badr-skew-ps = <0>;
+	devbus,acc-first-ps = <186000>;
+	devbus,acc-next-ps  = <186000>;
+
+	/* Write parameters */
+	devbus,wr-high-ps  = <90000>;
+	devbus,wr-low-ps   = <90000>;
+	devbus,ale-wr-ps   = <90000>;
+
+	/*
+	 * Currently the MTD code does not recognize the MX29LV400CBCT
+	 * as a bottom-type device. This could cause risks of
+	 * accidentally erasing critical flash sectors. We thus define
+	 * a single, write-protected partition covering the whole
+	 * flash.  TODO: once the flash part TOP/BOTTOM detection
+	 * issue is sorted out in the MTD code, break this into at
+	 * least three partitions: 'u-boot code', 'u-boot environment'
+	 * and 'whatever is left'.
+	 */
+	flash@0 {
+		compatible = "cfi-flash";
+		reg = <0 0x80000>;
+		bank-width = <1>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "Full512Kb";
+			reg = <0 0x80000>;
+			read-only;
+		};
 	};
 };
 
+&ehci0 {
+	status = "okay";
+};
+
 &eth {
 	status = "okay";
 
@@ -69,3 +115,60 @@
 		phy-handle = <&ethphy>;
 	};
 };
+
+&i2c {
+	status = "okay";
+	clock-frequency = <100000>;
+	#address-cells = <1>;
+
+	rtc@32 {
+		compatible = "ricoh,rs5c372a";
+		reg = <0x32>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy: ethernet-phy {
+		reg = <8>;
+	};
+};
+
+&pinctrl {
+	pinctrl-0 = <&pmx_rtc &pmx_power_led_ctrl>;
+	pinctrl-names = "default";
+
+	pmx_power_button: pmx-power-button {
+		marvell,pins = "mpp18";
+		marvell,function = "gpio";
+	};
+
+	pmx_power_led: pmx-power-led {
+		marvell,pins = "mpp16";
+		marvell,function = "gpio";
+	};
+
+	pmx_power_led_ctrl: pmx-power-led-ctrl {
+		marvell,pins = "mpp17";
+		marvell,function = "gpio";
+	};
+
+	pmx_rtc: pmx-rtc {
+		marvell,pins = "mpp3";
+		marvell,function = "gpio";
+	};
+};
+
+&sata {
+	pinctrl-0 = <&pmx_sata0 &pmx_sata1>;
+	pinctrl-names = "default";
+	status = "okay";
+	nr-ports = <2>;
+};
+
+&uart0 {
+	status = "okay";
+};

arch/arm/boot/dts/orion5x-maxtor-shared-storage-2.dts

@@ -0,0 +1,178 @@
+/*
+ * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ * Copyright (C) Sylver Bruneau <sylver.bruneau@googlemail.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "orion5x-mv88f5182.dtsi"
+
+/ {
+	model = "Maxtor Shared Storage II";
+	compatible = "maxtor,shared-storage-2", "marvell,orion5x-88f5182", "marvell,orion5x";
+
+	memory {
+		reg = <0x00000000 0x4000000>; /* 64 MB */
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		linux,stdout-path = &uart0;
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>,
+			 <MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>,
+			 <MBUS_ID(0x01, 0x0f) 0 0xff800000 0x40000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&pmx_buttons>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power {
+			label = "Power";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+		};
+
+		reset {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&devbus_bootcs {
+	status = "okay";
+
+	devbus,keep-config;
+
+	/*
+	 * Currently the MTD code does not recognize the MX29LV400CBCT
+	 * as a bottom-type device. This could cause risks of
+	 * accidentally erasing critical flash sectors. We thus define
+	 * a single, write-protected partition covering the whole
+	 * flash.  TODO: once the flash part TOP/BOTTOM detection
+	 * issue is sorted out in the MTD code, break this into at
+	 * least three partitions: 'u-boot code', 'u-boot environment'
+	 * and 'whatever is left'.
+	 */
+	flash@0 {
+		compatible = "cfi-flash";
+		reg = <0 0x40000>;
+		bank-width = <1>;
+                #address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy: ethernet-phy {
+		reg = <8>;
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	ethernet-port@0 {
+		phy-handle = <&ethphy>;
+	};
+};
+
+&i2c {
+	status = "okay";
+	clock-frequency = <100000>;
+	#address-cells = <1>;
+
+	rtc@68 {
+		compatible = "st,m41t81";
+		reg = <0x68>;
+		pinctrl-0 = <&pmx_rtc>;
+		pinctrl-names = "default";
+		interrupt-parent = <&gpio0>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&pinctrl {
+	pinctrl-0 = <&pmx_leds &pmx_misc>;
+	pinctrl-names = "default";
+
+	pmx_buttons: pmx-buttons {
+		marvell,pins = "mpp11", "mpp12";
+		marvell,function = "gpio";
+	};
+
+	/*
+	 * MPP0: Power LED
+	 * MPP1: Error LED
+	 */
+	pmx_leds: pmx-leds {
+		marvell,pins = "mpp0", "mpp1";
+		marvell,function = "gpio";
+	};
+
+	/*
+	 * MPP4: HDD ind. (Single/Dual)
+	 * MPP5: HD0 5V control
+	 * MPP6: HD0 12V control
+	 * MPP7: HD1 5V control
+	 * MPP8: HD1 12V control
+	 */
+	pmx_misc: pmx-misc {
+		marvell,pins = "mpp4", "mpp5", "mpp6", "mpp7", "mpp8", "mpp10";
+		marvell,function = "gpio";
+	};
+
+	pmx_rtc: pmx-rtc {
+		marvell,pins = "mpp3";
+		marvell,function = "gpio";
+	};
+
+	pmx_sata0_led_active: pmx-sata0-led-active {
+		marvell,pins = "mpp14";
+		marvell,function = "sata0";
+	};
+
+	pmx_sata1_led_active: pmx-sata1-led-active {
+		marvell,pins = "mpp15";
+		marvell,function = "sata1";
+	};
+
+	/*
+	 * Non MPP GPIOs:
+	 *  GPIO 22: USB port 1 fuse (0 = Fail, 1 = Ok)
+	 *  GPIO 23: Blue front LED off
+	 *  GPIO 24: Inhibit board power off (0 = Disabled, 1 = Enabled)
+	 */
+};
+
+&sata {
+	pinctrl-0 = <&pmx_sata0_led_active
+		     &pmx_sata1_led_active>;
+	pinctrl-names = "default";
+	status = "okay";
+	nr-ports = <2>;
+};
+
+&uart0 {
+	status = "okay";
+};

arch/arm/boot/dts/orion5x-mv88f5182.dtsi

@@ -0,0 +1,45 @@
+/*
+ * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include "orion5x.dtsi"
+
+/ {
+	compatible = "marvell,orion5x-88f5182", "marvell,orion5x";
+
+	soc {
+		compatible = "marvell,orion5x-88f5182-mbus", "simple-bus";
+
+		internal-regs {
+			pinctrl: pinctrl@10000 {
+				compatible = "marvell,88f5182-pinctrl";
+				reg = <0x10000 0x8>, <0x10050 0x4>;
+
+				pmx_sata0: pmx-sata0 {
+					marvell,pins = "mpp12", "mpp14";
+					marvell,function = "sata0";
+				};
+
+				pmx_sata1: pmx-sata1 {
+					marvell,pins = "mpp13", "mpp15";
+					marvell,function = "sata1";
+				};
+			};
+
+			core_clk: core-clocks@10030 {
+				compatible = "marvell,mv88f5182-core-clock";
+				reg = <0x10010 0x4>;
+				#clock-cells = <1>;
+			};
+
+			mbusc: mbus-controller@20000 {
+				compatible = "marvell,mbus-controller";
+				reg = <0x20000 0x100>, <0x1500 0x20>;
+			};
+		};
+	};
+};

arch/arm/boot/dts/orion5x-rd88f5182-nas.dts

@@ -0,0 +1,177 @@
+/*
+ * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "orion5x-mv88f5182.dtsi"
+
+/ {
+	model = "Marvell Reference Design 88F5182 NAS";
+	compatible = "marvell,rd-88f5182-nas", "marvell,orion5x-88f5182", "marvell,orion5x";
+
+	memory {
+		reg = <0x00000000 0x4000000>; /* 64 MB */
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		linux,stdout-path = &uart0;
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>,
+		         <MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>,
+			 <MBUS_ID(0x01, 0x0f) 0 0xf4000000 0x80000>,
+			 <MBUS_ID(0x01, 0x1d) 0 0xfc000000 0x1000000>;
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_debug_led>;
+		pinctrl-names = "default";
+
+		led@0 {
+			label = "rd88f5182:cpu";
+			linux,default-trigger = "heartbeat";
+			gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};
+
+&devbus_bootcs {
+	status = "okay";
+
+	/* Read parameters */
+	devbus,bus-width    = <8>;
+	devbus,turn-off-ps  = <90000>;
+	devbus,badr-skew-ps = <0>;
+	devbus,acc-first-ps = <186000>;
+	devbus,acc-next-ps  = <186000>;
+
+	/* Write parameters */
+	devbus,wr-high-ps  = <90000>;
+	devbus,wr-low-ps   = <90000>;
+	devbus,ale-wr-ps   = <90000>;
+
+	flash@0 {
+		compatible = "cfi-flash";
+		reg = <0 0x80000>;
+		bank-width = <1>;
+	};
+};
+
+&devbus_cs1 {
+	status = "okay";
+
+	/* Read parameters */
+	devbus,bus-width    = <8>;
+	devbus,turn-off-ps  = <90000>;
+	devbus,badr-skew-ps = <0>;
+	devbus,acc-first-ps = <186000>;
+	devbus,acc-next-ps  = <186000>;
+
+	/* Write parameters */
+	devbus,wr-high-ps  = <90000>;
+	devbus,wr-low-ps   = <90000>;
+	devbus,ale-wr-ps   = <90000>;
+
+	flash@0 {
+		compatible = "cfi-flash";
+		reg = <0 0x1000000>;
+		bank-width = <1>;
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	ethernet-port@0 {
+		phy-handle = <&ethphy>;
+	};
+};
+
+&i2c {
+	status = "okay";
+	clock-frequency = <100000>;
+	#address-cells = <1>;
+
+	rtc@68 {
+		pinctrl-0 = <&pmx_rtc>;
+		pinctrl-names = "default";
+		compatible = "dallas,ds1338";
+		reg = <0x68>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy: ethernet-phy {
+		reg = <8>;
+	};
+};
+
+&pinctrl {
+	pinctrl-0 = <&pmx_reset_switch &pmx_misc_gpios
+		&pmx_pci_gpios>;
+	pinctrl-names = "default";
+
+	/*
+	 * MPP[20] PCI Clock to MV88F5182
+	 * MPP[21] PCI Clock to mini PCI CON11
+	 * MPP[22] USB 0 over current indication
+	 * MPP[23] USB 1 over current indication
+	 * MPP[24] USB 1 over current enable
+	 * MPP[25] USB 0 over current enable
+	 */
+
+	pmx_debug_led: pmx-debug_led {
+		marvell,pins = "mpp0";
+		marvell,function = "gpio";
+	};
+
+	pmx_reset_switch: pmx-reset-switch {
+		marvell,pins = "mpp1";
+		marvell,function = "gpio";
+	};
+
+	pmx_rtc: pmx-rtc {
+		marvell,pins = "mpp3";
+		marvell,function = "gpio";
+	};
+
+	pmx_misc_gpios: pmx-misc-gpios {
+		marvell,pins = "mpp4", "mpp5";
+		marvell,function = "gpio";
+	};
+
+	pmx_pci_gpios: pmx-pci-gpios {
+		marvell,pins = "mpp6", "mpp7";
+		marvell,function = "gpio";
+	};
+};
+
+&sata {
+	pinctrl-0 = <&pmx_sata0 &pmx_sata1>;
+	pinctrl-names = "default";
+	status = "okay";
+	nr-ports = <2>;
+};
+
+&uart0 {
+	status = "okay";
+};

arch/arm/boot/dts/orion5x.dtsi

@@ -6,7 +6,9 @@
  * warranty of any kind, whether express or implied.
  */
 
-/include/ "skeleton.dtsi"
+#include "skeleton.dtsi"
+
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
 
 / {
 	model = "Marvell Orion5x SoC";
@@ -17,149 +19,214 @@
 		gpio0 = &gpio0;
 	};
 
-	intc: interrupt-controller {
-		compatible = "marvell,orion-intc";
-		interrupt-controller;
-		#interrupt-cells = <1>;
-		reg = <0xf1020200 0x08>;
-	};
-
-	ocp@f1000000 {
-		compatible = "simple-bus";
-		ranges = <0x00000000 0xf1000000 0x4000000
-		          0xf2200000 0xf2200000 0x0000800>;
-		#address-cells = <1>;
+	soc {
+		#address-cells = <2>;
 		#size-cells = <1>;
+		controller = <&mbusc>;
 
-		gpio0: gpio@10100 {
-			compatible = "marvell,orion-gpio";
-			#gpio-cells = <2>;
-			gpio-controller;
-			reg = <0x10100 0x40>;
-			ngpios = <32>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			interrupts = <6>, <7>, <8>, <9>;
-		};
-
-		spi@10600 {
-			compatible = "marvell,orion-spi";
+		devbus_bootcs: devbus-bootcs {
+			compatible = "marvell,orion-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x1046C 0x4>;
+			ranges = <0 MBUS_ID(0x01, 0x0f) 0 0xffffffff>;
 			#address-cells = <1>;
-			#size-cells = <0>;
-			cell-index = <0>;
-			reg = <0x10600 0x28>;
+			#size-cells = <1>;
+			clocks = <&core_clk 0>;
 			status = "disabled";
 		};
 
-		i2c@11000 {
-			compatible = "marvell,mv64xxx-i2c";
-			reg = <0x11000 0x20>;
+		devbus_cs0: devbus-cs0 {
+			compatible = "marvell,orion-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x1045C 0x4>;
+			ranges = <0 MBUS_ID(0x01, 0x1e) 0 0xffffffff>;
 			#address-cells = <1>;
-			#size-cells = <0>;
-			interrupts = <5>;
-			clock-frequency = <100000>;
+			#size-cells = <1>;
+			clocks = <&core_clk 0>;
 			status = "disabled";
 		};
 
-		serial@12000 {
-			compatible = "ns16550a";
-			reg = <0x12000 0x100>;
-			reg-shift = <2>;
-			interrupts = <3>;
-			/* set clock-frequency in board dts */
+		devbus_cs1: devbus-cs1 {
+			compatible = "marvell,orion-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10460 0x4>;
+			ranges = <0 MBUS_ID(0x01, 0x1d) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&core_clk 0>;
 			status = "disabled";
 		};
 
-		serial@12100 {
-			compatible = "ns16550a";
-			reg = <0x12100 0x100>;
-			reg-shift = <2>;
-			interrupts = <4>;
-			/* set clock-frequency in board dts */
+		devbus_cs2: devbus-cs2 {
+			compatible = "marvell,orion-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10464 0x4>;
+			ranges = <0 MBUS_ID(0x01, 0x1b) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&core_clk 0>;
 			status = "disabled";
 		};
 
-		wdt@20300 {
-			compatible = "marvell,orion-wdt";
-			reg = <0x20300 0x28>;
-			status = "okay";
-		};
+		internal-regs {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
+
+			gpio0: gpio@10100 {
+				compatible = "marvell,orion-gpio";
+				#gpio-cells = <2>;
+				gpio-controller;
+				reg = <0x10100 0x40>;
+				ngpios = <32>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <6>, <7>, <8>, <9>;
+			};
 
-		ehci@50000 {
-			compatible = "marvell,orion-ehci";
-			reg = <0x50000 0x1000>;
-			interrupts = <17>;
-			status = "disabled";
-		};
+			spi: spi@10600 {
+				compatible = "marvell,orion-spi";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				cell-index = <0>;
+				reg = <0x10600 0x28>;
+				status = "disabled";
+			};
 
-		xor@60900 {
-			compatible = "marvell,orion-xor";
-			reg = <0x60900 0x100
-			       0x60b00 0x100>;
-			status = "okay";
+			i2c: i2c@11000 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11000 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <5>;
+				clocks = <&core_clk 0>;
+				status = "disabled";
+			};
 
-			xor00 {
-			      interrupts = <30>;
-			      dmacap,memcpy;
-			      dmacap,xor;
+			uart0: serial@12000 {
+				compatible = "ns16550a";
+				reg = <0x12000 0x100>;
+				reg-shift = <2>;
+				interrupts = <3>;
+				clocks = <&core_clk 0>;
+				status = "disabled";
 			};
-			xor01 {
-			      interrupts = <31>;
-			      dmacap,memcpy;
-			      dmacap,xor;
-			      dmacap,memset;
+
+			uart1: serial@12100 {
+				compatible = "ns16550a";
+				reg = <0x12100 0x100>;
+				reg-shift = <2>;
+				interrupts = <4>;
+				clocks = <&core_clk 0>;
+				status = "disabled";
 			};
-		};
 
-		eth: ethernet-controller@72000 {
-			compatible = "marvell,orion-eth";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x72000 0x4000>;
-			marvell,tx-checksum-limit = <1600>;
-			status = "disabled";
+			bridge_intc: bridge-interrupt-ctrl@20110 {
+				compatible = "marvell,orion-bridge-intc";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				reg = <0x20110 0x8>;
+				interrupts = <0>;
+				marvell,#interrupts = <4>;
+			};
 
-			ethernet-port@0 {
-				compatible = "marvell,orion-eth-port";
-				reg = <0>;
-				/* overwrite MAC address in bootloader */
-				local-mac-address = [00 00 00 00 00 00];
-				/* set phy-handle property in board file */
+			intc: interrupt-controller@20200 {
+				compatible = "marvell,orion-intc";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				reg = <0x20200 0x08>;
 			};
-		};
 
-		mdio: mdio-bus@72004 {
-			compatible = "marvell,orion-mdio";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0x72004 0x84>;
-			interrupts = <22>;
-			status = "disabled";
+			timer: timer@20300 {
+				compatible = "marvell,orion-timer";
+				reg = <0x20300 0x20>;
+				interrupt-parent = <&bridge_intc>;
+				interrupts = <1>, <2>;
+				clocks = <&core_clk 0>;
+			};
 
-			/* add phy nodes in board file */
-		};
+			wdt: wdt@20300 {
+				compatible = "marvell,orion-wdt";
+				reg = <0x20300 0x28>;
+				interrupt-parent = <&bridge_intc>;
+				interrupts = <3>;
+				status = "okay";
+			};
 
-		sata@80000 {
-			compatible = "marvell,orion-sata";
-			reg = <0x80000 0x5000>;
-			interrupts = <29>;
-			status = "disabled";
+			ehci0: ehci@50000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x50000 0x1000>;
+				interrupts = <17>;
+				status = "disabled";
+			};
+
+			xor: dma-controller@60900 {
+				compatible = "marvell,orion-xor";
+				reg = <0x60900 0x100
+				       0x60b00 0x100>;
+				status = "okay";
+
+				xor00 {
+				      interrupts = <30>;
+				      dmacap,memcpy;
+				      dmacap,xor;
+				};
+				xor01 {
+				      interrupts = <31>;
+				      dmacap,memcpy;
+				      dmacap,xor;
+				      dmacap,memset;
+				};
+			};
+
+			eth: ethernet-controller@72000 {
+				compatible = "marvell,orion-eth";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x72000 0x4000>;
+				marvell,tx-checksum-limit = <1600>;
+				status = "disabled";
+
+				ethport: ethernet-port@0 {
+					compatible = "marvell,orion-eth-port";
+					reg = <0>;
+					interrupts = <21>;
+					/* overwrite MAC address in bootloader */
+					local-mac-address = [00 00 00 00 00 00];
+					/* set phy-handle property in board file */
+				};
+			};
+
+			mdio: mdio-bus@72004 {
+				compatible = "marvell,orion-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0x72004 0x84>;
+				interrupts = <22>;
+				status = "disabled";
+
+				/* add phy nodes in board file */
+			};
+
+			sata: sata@80000 {
+				compatible = "marvell,orion-sata";
+				reg = <0x80000 0x5000>;
+				interrupts = <29>;
+				status = "disabled";
+			};
+
+			ehci1: ehci@a0000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0xa0000 0x1000>;
+				interrupts = <12>;
+				status = "disabled";
+			};
 		};
 
-		crypto@90000 {
+		cesa: crypto@90000 {
 			compatible = "marvell,orion-crypto";
-			reg = <0x90000 0x10000>,
-			      <0xf2200000 0x800>;
+			reg = <MBUS_ID(0xf0, 0x01) 0x90000 0x10000>,
+			      <MBUS_ID(0x09, 0x00) 0x0 0x800>;
 			reg-names = "regs", "sram";
 			interrupts = <28>;
 			status = "okay";
 		};
-
-		ehci@a0000 {
-			compatible = "marvell,orion-ehci";
-			reg = <0xa0000 0x1000>;
-			interrupts = <12>;
-			status = "disabled";
-		};
 	};
 };

arch/arm/mach-dove/irq.c

@@ -108,6 +108,38 @@ static int __initdata gpio2_irqs[4] = {
 	0,
 };
 
+#ifdef CONFIG_MULTI_IRQ_HANDLER
+/*
+ * Compiling with both non-DT and DT support enabled, will
+ * break asm irq handler used by non-DT boards. Therefore,
+ * we provide a C-style irq handler even for non-DT boards,
+ * if MULTI_IRQ_HANDLER is set.
+ */
+
+static void __iomem *dove_irq_base = IRQ_VIRT_BASE;
+
+static asmlinkage void
+__exception_irq_entry dove_legacy_handle_irq(struct pt_regs *regs)
+{
+	u32 stat;
+
+	stat = readl_relaxed(dove_irq_base + IRQ_CAUSE_LOW_OFF);
+	stat &= readl_relaxed(dove_irq_base + IRQ_MASK_LOW_OFF);
+	if (stat) {
+		unsigned int hwirq = __fls(stat);
+		handle_IRQ(hwirq, regs);
+		return;
+	}
+	stat = readl_relaxed(dove_irq_base + IRQ_CAUSE_HIGH_OFF);
+	stat &= readl_relaxed(dove_irq_base + IRQ_MASK_HIGH_OFF);
+	if (stat) {
+		unsigned int hwirq = 32 + __fls(stat);
+		handle_IRQ(hwirq, regs);
+		return;
+	}
+}
+#endif
+
 void __init dove_init_irq(void)
 {
 	int i;
@@ -115,6 +147,10 @@ void __init dove_init_irq(void)
 	orion_irq_init(0, IRQ_VIRT_BASE + IRQ_MASK_LOW_OFF);
 	orion_irq_init(32, IRQ_VIRT_BASE + IRQ_MASK_HIGH_OFF);
 
+#ifdef CONFIG_MULTI_IRQ_HANDLER
+	set_handle_irq(dove_legacy_handle_irq);
+#endif
+
 	/*
 	 * Initialize gpiolib for GPIOs 0-71.
 	 */

arch/arm/mach-kirkwood/irq.c

@@ -7,6 +7,7 @@
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
  */
+#include <asm/exception.h>
 #include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/irq.h>
@@ -30,11 +31,47 @@ static int __initdata gpio1_irqs[4] = {
 	0,
 };
 
+#ifdef CONFIG_MULTI_IRQ_HANDLER
+/*
+ * Compiling with both non-DT and DT support enabled, will
+ * break asm irq handler used by non-DT boards. Therefore,
+ * we provide a C-style irq handler even for non-DT boards,
+ * if MULTI_IRQ_HANDLER is set.
+ */
+
+static void __iomem *kirkwood_irq_base = IRQ_VIRT_BASE;
+
+asmlinkage void
+__exception_irq_entry kirkwood_legacy_handle_irq(struct pt_regs *regs)
+{
+	u32 stat;
+
+	stat = readl_relaxed(kirkwood_irq_base + IRQ_CAUSE_LOW_OFF);
+	stat &= readl_relaxed(kirkwood_irq_base + IRQ_MASK_LOW_OFF);
+	if (stat) {
+		unsigned int hwirq = __fls(stat);
+		handle_IRQ(hwirq, regs);
+		return;
+	}
+	stat = readl_relaxed(kirkwood_irq_base + IRQ_CAUSE_HIGH_OFF);
+	stat &= readl_relaxed(kirkwood_irq_base + IRQ_MASK_HIGH_OFF);
+	if (stat) {
+		unsigned int hwirq = 32 + __fls(stat);
+		handle_IRQ(hwirq, regs);
+		return;
+	}
+}
+#endif
+
 void __init kirkwood_init_irq(void)
 {
 	orion_irq_init(0, IRQ_VIRT_BASE + IRQ_MASK_LOW_OFF);
 	orion_irq_init(32, IRQ_VIRT_BASE + IRQ_MASK_HIGH_OFF);
 
+#ifdef CONFIG_MULTI_IRQ_HANDLER
+	set_handle_irq(kirkwood_legacy_handle_irq);
+#endif
+
 	/*
 	 * Initialize gpiolib for GPIOs 0-49.
 	 */

arch/arm/mach-orion5x/Kconfig

@@ -5,6 +5,11 @@ menu "Orion Implementations"
 config ARCH_ORION5X_DT
 	bool "Marvell Orion5x Flattened Device Tree"
 	select USE_OF
+	select ORION_CLK
+	select ORION_IRQCHIP
+	select ORION_TIMER
+	select PINCTRL
+	select PINCTRL_ORION
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell Orion5x using flattened device tree.
@@ -23,6 +28,14 @@ config MACH_RD88F5182
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell Orion-NAS (88F5182) RD2
 
+config MACH_RD88F5182_DT
+	bool "Marvell Orion-NAS Reference Design (Flattened Device Tree)"
+	select ARCH_ORION5X_DT
+	select I2C_BOARDINFO
+	help
+	  Say 'Y' here if you want your kernel to support the Marvell
+	  Orion-NAS (88F5182) RD2, Flattened Device Tree.
+
 config MACH_KUROBOX_PRO
 	bool "KuroBox Pro"
 	select I2C_BOARDINFO
@@ -102,28 +115,13 @@ config MACH_MV2120
 	  Say 'Y' here if you want your kernel to support the
 	  HP Media Vault mv2120 or mv5100.
 
-config MACH_EDMINI_V2_DT
-	bool "LaCie Ethernet Disk mini V2 (Flattened Device Tree)"
-	select I2C_BOARDINFO
+config MACH_D2NET_DT
+	bool "LaCie d2 Network / Big Disk Network (Flattened Device Tree)"
 	select ARCH_ORION5X_DT
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  LaCie Ethernet Disk mini V2 (Flattened Device Tree).
-
-config MACH_D2NET
-	bool "LaCie d2 Network"
-	select I2C_BOARDINFO
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  LaCie d2 Network NAS.
 
-config MACH_BIGDISK
-	bool "LaCie Big Disk Network"
-	select I2C_BOARDINFO
-	help
-	  Say 'Y' here if you want your kernel to support the
-	  LaCie Big Disk Network NAS.
-
 config MACH_NET2BIG
 	bool "LaCie 2Big Network"
 	select I2C_BOARDINFO
@@ -131,8 +129,9 @@ config MACH_NET2BIG
 	  Say 'Y' here if you want your kernel to support the
 	  LaCie 2Big Network NAS.
 
-config MACH_MSS2
-	bool "Maxtor Shared Storage II"
+config MACH_MSS2_DT
+	bool "Maxtor Shared Storage II (Flattened Device Tree)"
+	select ARCH_ORION5X_DT
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Maxtor Shared Storage II platform.

arch/arm/mach-orion5x/Makefile

@@ -12,10 +12,7 @@ obj-$(CONFIG_MACH_TS409)	+= ts409-setup.o tsx09-common.o
 obj-$(CONFIG_MACH_WRT350N_V2)	+= wrt350n-v2-setup.o
 obj-$(CONFIG_MACH_TS78XX)	+= ts78xx-setup.o
 obj-$(CONFIG_MACH_MV2120)	+= mv2120-setup.o
-obj-$(CONFIG_MACH_D2NET)	+= d2net-setup.o
-obj-$(CONFIG_MACH_BIGDISK)	+= d2net-setup.o
 obj-$(CONFIG_MACH_NET2BIG)	+= net2big-setup.o
-obj-$(CONFIG_MACH_MSS2)		+= mss2-setup.o
 obj-$(CONFIG_MACH_WNR854T)	+= wnr854t-setup.o
 obj-$(CONFIG_MACH_RD88F5181L_GE)	+= rd88f5181l-ge-setup.o
 obj-$(CONFIG_MACH_RD88F5181L_FXO)	+= rd88f5181l-fxo-setup.o
@@ -23,4 +20,6 @@ obj-$(CONFIG_MACH_RD88F6183AP_GE)	+= rd88f6183ap-ge-setup.o
 obj-$(CONFIG_MACH_LINKSTATION_LSCHL)	+= ls-chl-setup.o
 
 obj-$(CONFIG_ARCH_ORION5X_DT)		+= board-dt.o
-obj-$(CONFIG_MACH_EDMINI_V2_DT)	+= edmini_v2-setup.o
+obj-$(CONFIG_MACH_D2NET_DT)	+= board-d2net.o
+obj-$(CONFIG_MACH_MSS2_DT)	+= board-mss2.o
+obj-$(CONFIG_MACH_RD88F5182_DT)	+= board-rd88f5182.o

arch/arm/mach-orion5x/board-d2net.c

@@ -0,0 +1,109 @@
+/*
+ * arch/arm/mach-orion5x/board-d2net.c
+ *
+ * LaCie d2Network and Big Disk Network NAS setup
+ *
+ * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/pci.h>
+#include <linux/irq.h>
+#include <linux/leds.h>
+#include <linux/gpio.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/pci.h>
+#include <mach/orion5x.h>
+#include <plat/orion-gpio.h>
+#include "common.h"
+
+/*****************************************************************************
+ * LaCie d2 Network Info
+ ****************************************************************************/
+
+/*****************************************************************************
+ * GPIO LED's
+ ****************************************************************************/
+
+/*
+ * The blue front LED is wired to the CPLD and can blink in relation with the
+ * SATA activity.
+ *
+ * The following array detail the different LED registers and the combination
+ * of their possible values:
+ *
+ * led_off   | blink_ctrl | SATA active | LED state
+ *           |            |             |
+ *    1      |     x      |      x      |  off
+ *    0      |     0      |      0      |  off
+ *    0      |     1      |      0      |  blink (rate 300ms)
+ *    0      |     x      |      1      |  on
+ *
+ * Notes: The blue and the red front LED's can't be on at the same time.
+ *        Red LED have priority.
+ */
+
+#define D2NET_GPIO_RED_LED		6
+#define D2NET_GPIO_BLUE_LED_BLINK_CTRL	16
+#define D2NET_GPIO_BLUE_LED_OFF		23
+
+static struct gpio_led d2net_leds[] = {
+	{
+		.name = "d2net:blue:sata",
+		.default_trigger = "default-on",
+		.gpio = D2NET_GPIO_BLUE_LED_OFF,
+		.active_low = 1,
+	},
+	{
+		.name = "d2net:red:fail",
+		.gpio = D2NET_GPIO_RED_LED,
+	},
+};
+
+static struct gpio_led_platform_data d2net_led_data = {
+	.num_leds = ARRAY_SIZE(d2net_leds),
+	.leds = d2net_leds,
+};
+
+static struct platform_device d2net_gpio_leds = {
+	.name           = "leds-gpio",
+	.id             = -1,
+	.dev            = {
+		.platform_data  = &d2net_led_data,
+	},
+};
+
+static void __init d2net_gpio_leds_init(void)
+{
+	int err;
+
+	/* Configure register blink_ctrl to allow SATA activity LED blinking. */
+	err = gpio_request(D2NET_GPIO_BLUE_LED_BLINK_CTRL, "blue LED blink");
+	if (err == 0) {
+		err = gpio_direction_output(D2NET_GPIO_BLUE_LED_BLINK_CTRL, 1);
+		if (err)
+			gpio_free(D2NET_GPIO_BLUE_LED_BLINK_CTRL);
+	}
+	if (err)
+		pr_err("d2net: failed to configure blue LED blink GPIO\n");
+
+	platform_device_register(&d2net_gpio_leds);
+}
+
+/*****************************************************************************
+ * General Setup
+ ****************************************************************************/
+
+void __init d2net_init(void)
+{
+	d2net_gpio_leds_init();
+
+	pr_notice("d2net: Flash write are not yet supported.\n");
+}

arch/arm/mach-orion5x/board-dt.c

@@ -15,10 +15,16 @@
 #include <linux/of.h>
 #include <linux/of_platform.h>
 #include <linux/cpu.h>
+#include <linux/mbus.h>
+#include <linux/clk-provider.h>
+#include <linux/clocksource.h>
 #include <asm/system_misc.h>
 #include <asm/mach/arch.h>
+#include <asm/mach/map.h>
 #include <mach/orion5x.h>
+#include <mach/bridge-regs.h>
 #include <plat/irq.h>
+#include <plat/time.h>
 #include "common.h"
 
 static struct of_dev_auxdata orion5x_auxdata_lookup[] __initdata = {
@@ -39,14 +45,13 @@ static void __init orion5x_dt_init(void)
 	orion5x_id(&dev, &rev, &dev_name);
 	printk(KERN_INFO "Orion ID: %s. TCLK=%d.\n", dev_name, orion5x_tclk);
 
+	BUG_ON(mvebu_mbus_dt_init());
+
 	/*
 	 * Setup Orion address map
 	 */
 	orion5x_setup_wins();
 
-	/* Setup root of clk tree */
-	clk_init();
-
 	/*
 	 * Don't issue "Wait for Interrupt" instruction if we are
 	 * running on D0 5281 silicon.
@@ -56,8 +61,8 @@ static void __init orion5x_dt_init(void)
 		cpu_idle_poll_ctrl(true);
 	}
 
-	if (of_machine_is_compatible("lacie,ethernet-disk-mini-v2"))
-		edmini_v2_init();
+	if (of_machine_is_compatible("maxtor,shared-storage-2"))
+		mss2_init();
 
 	of_platform_populate(NULL, of_default_bus_match_table,
 			     orion5x_auxdata_lookup, NULL);
@@ -71,9 +76,6 @@ static const char *orion5x_dt_compat[] = {
 DT_MACHINE_START(ORION5X_DT, "Marvell Orion5x (Flattened Device Tree)")
 	/* Maintainer: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> */
 	.map_io		= orion5x_map_io,
-	.init_early	= orion5x_init_early,
-	.init_irq	= orion_dt_init_irq,
-	.init_time	= orion5x_timer_init,
 	.init_machine	= orion5x_dt_init,
 	.restart	= orion5x_restart,
 	.dt_compat	= orion5x_dt_compat,

arch/arm/mach-orion5x/board-mss2.c

@@ -0,0 +1,90 @@
+/*
+ * Maxtor Shared Storage II Board Setup
+ *
+ * Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/pci.h>
+#include <linux/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/pci.h>
+#include <mach/orion5x.h>
+#include <mach/bridge-regs.h>
+#include "common.h"
+
+/*****************************************************************************
+ * Maxtor Shared Storage II Info
+ ****************************************************************************/
+
+/****************************************************************************
+ * PCI setup
+ ****************************************************************************/
+static int __init mss2_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	int irq;
+
+	/*
+	 * Check for devices with hard-wired IRQs.
+	 */
+	irq = orion5x_pci_map_irq(dev, slot, pin);
+	if (irq != -1)
+		return irq;
+
+	return -1;
+}
+
+static struct hw_pci mss2_pci __initdata = {
+	.nr_controllers = 2,
+	.setup		= orion5x_pci_sys_setup,
+	.scan		= orion5x_pci_sys_scan_bus,
+	.map_irq	= mss2_pci_map_irq,
+};
+
+static int __init mss2_pci_init(void)
+{
+	if (machine_is_mss2())
+		pci_common_init(&mss2_pci);
+
+	return 0;
+}
+subsys_initcall(mss2_pci_init);
+
+/*****************************************************************************
+ * MSS2 power off method
+ ****************************************************************************/
+/*
+ * On the Maxtor Shared Storage II, the shutdown process is the following :
+ * - Userland modifies U-boot env to tell U-boot to go idle at next boot
+ * - The board reboots
+ * - U-boot starts and go into an idle mode until the user press "power"
+ */
+static void mss2_power_off(void)
+{
+	u32 reg;
+
+	/*
+	 * Enable and issue soft reset
+	 */
+	reg = readl(RSTOUTn_MASK);
+	reg |= 1 << 2;
+	writel(reg, RSTOUTn_MASK);
+
+	reg = readl(CPU_SOFT_RESET);
+	reg |= 1;
+	writel(reg, CPU_SOFT_RESET);
+}
+
+void __init mss2_init(void)
+{
+	/* register mss2 specific power-off method */
+	pm_power_off = mss2_power_off;
+}

arch/arm/mach-orion5x/board-rd88f5182.c

@@ -0,0 +1,116 @@
+/*
+ * arch/arm/mach-orion5x/rd88f5182-setup.c
+ *
+ * Marvell Orion-NAS Reference Design Setup
+ *
+ * Maintainer: Ronen Shitrit <rshitrit@marvell.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <linux/gpio.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/pci.h>
+#include <linux/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/pci.h>
+#include <mach/orion5x.h>
+#include "common.h"
+
+/*****************************************************************************
+ * RD-88F5182 Info
+ ****************************************************************************/
+
+/*
+ * PCI
+ */
+
+#define RD88F5182_PCI_SLOT0_OFFS	7
+#define RD88F5182_PCI_SLOT0_IRQ_A_PIN	7
+#define RD88F5182_PCI_SLOT0_IRQ_B_PIN	6
+
+/*****************************************************************************
+ * PCI
+ ****************************************************************************/
+
+static void __init rd88f5182_pci_preinit(void)
+{
+	int pin;
+
+	/*
+	 * Configure PCI GPIO IRQ pins
+	 */
+	pin = RD88F5182_PCI_SLOT0_IRQ_A_PIN;
+	if (gpio_request(pin, "PCI IntA") == 0) {
+		if (gpio_direction_input(pin) == 0) {
+			irq_set_irq_type(gpio_to_irq(pin), IRQ_TYPE_LEVEL_LOW);
+		} else {
+			printk(KERN_ERR "rd88f5182_pci_preinit failed to "
+					"set_irq_type pin %d\n", pin);
+			gpio_free(pin);
+		}
+	} else {
+		printk(KERN_ERR "rd88f5182_pci_preinit failed to request gpio %d\n", pin);
+	}
+
+	pin = RD88F5182_PCI_SLOT0_IRQ_B_PIN;
+	if (gpio_request(pin, "PCI IntB") == 0) {
+		if (gpio_direction_input(pin) == 0) {
+			irq_set_irq_type(gpio_to_irq(pin), IRQ_TYPE_LEVEL_LOW);
+		} else {
+			printk(KERN_ERR "rd88f5182_pci_preinit failed to "
+					"set_irq_type pin %d\n", pin);
+			gpio_free(pin);
+		}
+	} else {
+		printk(KERN_ERR "rd88f5182_pci_preinit failed to gpio_request %d\n", pin);
+	}
+}
+
+static int __init rd88f5182_pci_map_irq(const struct pci_dev *dev, u8 slot,
+	u8 pin)
+{
+	int irq;
+
+	/*
+	 * Check for devices with hard-wired IRQs.
+	 */
+	irq = orion5x_pci_map_irq(dev, slot, pin);
+	if (irq != -1)
+		return irq;
+
+	/*
+	 * PCI IRQs are connected via GPIOs
+	 */
+	switch (slot - RD88F5182_PCI_SLOT0_OFFS) {
+	case 0:
+		if (pin == 1)
+			return gpio_to_irq(RD88F5182_PCI_SLOT0_IRQ_A_PIN);
+		else
+			return gpio_to_irq(RD88F5182_PCI_SLOT0_IRQ_B_PIN);
+	default:
+		return -1;
+	}
+}
+
+static struct hw_pci rd88f5182_pci __initdata = {
+	.nr_controllers	= 2,
+	.preinit	= rd88f5182_pci_preinit,
+	.setup		= orion5x_pci_sys_setup,
+	.scan		= orion5x_pci_sys_scan_bus,
+	.map_irq	= rd88f5182_pci_map_irq,
+};
+
+static int __init rd88f5182_pci_init(void)
+{
+	if (of_machine_is_compatible("marvell,rd-88f5182-nas"))
+		pci_common_init(&rd88f5182_pci);
+
+	return 0;
+}
+
+subsys_initcall(rd88f5182_pci_init);

arch/arm/mach-orion5x/common.h

@@ -64,17 +64,16 @@ int orion5x_pci_sys_setup(int nr, struct pci_sys_data *sys);
 struct pci_bus *orion5x_pci_sys_scan_bus(int nr, struct pci_sys_data *sys);
 int orion5x_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin);
 
-/* board init functions for boards not fully converted to fdt */
-#ifdef CONFIG_MACH_EDMINI_V2_DT
-void edmini_v2_init(void);
-#else
-static inline void edmini_v2_init(void) {};
-#endif
-
 struct meminfo;
 struct tag;
 extern void __init tag_fixup_mem32(struct tag *, char **, struct meminfo *);
 
+#ifdef CONFIG_MACH_MSS2_DT
+extern void mss2_init(void);
+#else
+static inline void mss2_init(void) {}
+#endif
+
 /*****************************************************************************
  * Helpers to access Orion registers
  ****************************************************************************/

arch/arm/mach-orion5x/d2net-setup.c

@@ -1,365 +0,0 @@
-/*
- * arch/arm/mach-orion5x/d2net-setup.c
- *
- * LaCie d2Network and Big Disk Network NAS setup
- *
- * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/pci.h>
-#include <linux/irq.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/leds.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/i2c.h>
-#include <linux/ata_platform.h>
-#include <linux/gpio.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-#include <mach/orion5x.h>
-#include <plat/orion-gpio.h>
-#include "common.h"
-#include "mpp.h"
-
-/*****************************************************************************
- * LaCie d2 Network Info
- ****************************************************************************/
-
-/*
- * 512KB NOR flash Device bus boot chip select
- */
-
-#define D2NET_NOR_BOOT_BASE		0xfff80000
-#define D2NET_NOR_BOOT_SIZE		SZ_512K
-
-/*****************************************************************************
- * 512KB NOR Flash on Boot Device
- ****************************************************************************/
-
-/*
- * TODO: Check write support on flash MX29LV400CBTC-70G
- */
-
-static struct mtd_partition d2net_partitions[] = {
-	{
-		.name		= "Full512kb",
-		.size		= MTDPART_SIZ_FULL,
-		.offset		= 0,
-		.mask_flags	= MTD_WRITEABLE,
-	},
-};
-
-static struct physmap_flash_data d2net_nor_flash_data = {
-	.width		= 1,
-	.parts		= d2net_partitions,
-	.nr_parts	= ARRAY_SIZE(d2net_partitions),
-};
-
-static struct resource d2net_nor_flash_resource = {
-	.flags			= IORESOURCE_MEM,
-	.start			= D2NET_NOR_BOOT_BASE,
-	.end			= D2NET_NOR_BOOT_BASE
-					+ D2NET_NOR_BOOT_SIZE - 1,
-};
-
-static struct platform_device d2net_nor_flash = {
-	.name			= "physmap-flash",
-	.id			= 0,
-	.dev		= {
-		.platform_data	= &d2net_nor_flash_data,
-	},
-	.num_resources		= 1,
-	.resource		= &d2net_nor_flash_resource,
-};
-
-/*****************************************************************************
- * Ethernet
- ****************************************************************************/
-
-static struct mv643xx_eth_platform_data d2net_eth_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-/*****************************************************************************
- * I2C devices
- ****************************************************************************/
-
-/*
- * i2c addr | chip         | description
- * 0x32     | Ricoh 5C372b | RTC
- * 0x3e     | GMT G762     | PWM fan controller
- * 0x50     | HT24LC08     | eeprom (1kB)
- *
- * TODO: Add G762 support to the g760a driver.
- */
-static struct i2c_board_info __initdata d2net_i2c_devices[] = {
-	{
-		I2C_BOARD_INFO("rs5c372b", 0x32),
-	}, {
-		I2C_BOARD_INFO("24c08", 0x50),
-	},
-};
-
-/*****************************************************************************
- * SATA
- ****************************************************************************/
-
-static struct mv_sata_platform_data d2net_sata_data = {
-	.n_ports	= 2,
-};
-
-#define D2NET_GPIO_SATA0_POWER	3
-#define D2NET_GPIO_SATA1_POWER	12
-
-static void __init d2net_sata_power_init(void)
-{
-	int err;
-
-	err = gpio_request(D2NET_GPIO_SATA0_POWER, "SATA0 power");
-	if (err == 0) {
-		err = gpio_direction_output(D2NET_GPIO_SATA0_POWER, 1);
-		if (err)
-			gpio_free(D2NET_GPIO_SATA0_POWER);
-	}
-	if (err)
-		pr_err("d2net: failed to configure SATA0 power GPIO\n");
-
-	err = gpio_request(D2NET_GPIO_SATA1_POWER, "SATA1 power");
-	if (err == 0) {
-		err = gpio_direction_output(D2NET_GPIO_SATA1_POWER, 1);
-		if (err)
-			gpio_free(D2NET_GPIO_SATA1_POWER);
-	}
-	if (err)
-		pr_err("d2net: failed to configure SATA1 power GPIO\n");
-}
-
-/*****************************************************************************
- * GPIO LED's
- ****************************************************************************/
-
-/*
- * The blue front LED is wired to the CPLD and can blink in relation with the
- * SATA activity.
- *
- * The following array detail the different LED registers and the combination
- * of their possible values:
- *
- * led_off   | blink_ctrl | SATA active | LED state
- *           |            |             |
- *    1      |     x      |      x      |  off
- *    0      |     0      |      0      |  off
- *    0      |     1      |      0      |  blink (rate 300ms)
- *    0      |     x      |      1      |  on
- *
- * Notes: The blue and the red front LED's can't be on at the same time.
- *        Red LED have priority.
- */
-
-#define D2NET_GPIO_RED_LED		6
-#define D2NET_GPIO_BLUE_LED_BLINK_CTRL	16
-#define D2NET_GPIO_BLUE_LED_OFF		23
-
-static struct gpio_led d2net_leds[] = {
-	{
-		.name = "d2net:blue:sata",
-		.default_trigger = "default-on",
-		.gpio = D2NET_GPIO_BLUE_LED_OFF,
-		.active_low = 1,
-	},
-	{
-		.name = "d2net:red:fail",
-		.gpio = D2NET_GPIO_RED_LED,
-	},
-};
-
-static struct gpio_led_platform_data d2net_led_data = {
-	.num_leds = ARRAY_SIZE(d2net_leds),
-	.leds = d2net_leds,
-};
-
-static struct platform_device d2net_gpio_leds = {
-	.name           = "leds-gpio",
-	.id             = -1,
-	.dev            = {
-		.platform_data  = &d2net_led_data,
-	},
-};
-
-static void __init d2net_gpio_leds_init(void)
-{
-	int err;
-
-	/* Configure GPIO over MPP max number. */
-	orion_gpio_set_valid(D2NET_GPIO_BLUE_LED_OFF, 1);
-
-	/* Configure register blink_ctrl to allow SATA activity LED blinking. */
-	err = gpio_request(D2NET_GPIO_BLUE_LED_BLINK_CTRL, "blue LED blink");
-	if (err == 0) {
-		err = gpio_direction_output(D2NET_GPIO_BLUE_LED_BLINK_CTRL, 1);
-		if (err)
-			gpio_free(D2NET_GPIO_BLUE_LED_BLINK_CTRL);
-	}
-	if (err)
-		pr_err("d2net: failed to configure blue LED blink GPIO\n");
-
-	platform_device_register(&d2net_gpio_leds);
-}
-
-/****************************************************************************
- * GPIO keys
- ****************************************************************************/
-
-#define D2NET_GPIO_PUSH_BUTTON		18
-#define D2NET_GPIO_POWER_SWITCH_ON	8
-#define D2NET_GPIO_POWER_SWITCH_OFF	9
-
-#define D2NET_SWITCH_POWER_ON		0x1
-#define D2NET_SWITCH_POWER_OFF		0x2
-
-static struct gpio_keys_button d2net_buttons[] = {
-	{
-		.type		= EV_SW,
-		.code		= D2NET_SWITCH_POWER_OFF,
-		.gpio		= D2NET_GPIO_POWER_SWITCH_OFF,
-		.desc		= "Power rocker switch (auto|off)",
-		.active_low	= 0,
-	},
-	{
-		.type		= EV_SW,
-		.code		= D2NET_SWITCH_POWER_ON,
-		.gpio		= D2NET_GPIO_POWER_SWITCH_ON,
-		.desc		= "Power rocker switch (on|auto)",
-		.active_low	= 0,
-	},
-	{
-		.type		= EV_KEY,
-		.code		= KEY_POWER,
-		.gpio		= D2NET_GPIO_PUSH_BUTTON,
-		.desc		= "Front Push Button",
-		.active_low	= 0,
-	},
-};
-
-static struct gpio_keys_platform_data d2net_button_data = {
-	.buttons	= d2net_buttons,
-	.nbuttons	= ARRAY_SIZE(d2net_buttons),
-};
-
-static struct platform_device d2net_gpio_buttons = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &d2net_button_data,
-	},
-};
-
-/*****************************************************************************
- * General Setup
- ****************************************************************************/
-
-static unsigned int d2net_mpp_modes[] __initdata = {
-	MPP0_GPIO,	/* Board ID (bit 0) */
-	MPP1_GPIO,	/* Board ID (bit 1) */
-	MPP2_GPIO,	/* Board ID (bit 2) */
-	MPP3_GPIO,	/* SATA 0 power */
-	MPP4_UNUSED,
-	MPP5_GPIO,	/* Fan fail detection */
-	MPP6_GPIO,	/* Red front LED */
-	MPP7_UNUSED,
-	MPP8_GPIO,	/* Rear power switch (on|auto) */
-	MPP9_GPIO,	/* Rear power switch (auto|off) */
-	MPP10_UNUSED,
-	MPP11_UNUSED,
-	MPP12_GPIO,	/* SATA 1 power */
-	MPP13_UNUSED,
-	MPP14_SATA_LED,	/* SATA 0 active */
-	MPP15_SATA_LED,	/* SATA 1 active */
-	MPP16_GPIO,	/* Blue front LED blink control */
-	MPP17_UNUSED,
-	MPP18_GPIO,	/* Front button (0 = Released, 1 = Pushed ) */
-	MPP19_UNUSED,
-	0,
-	/* 22: USB port 1 fuse (0 = Fail, 1 = Ok) */
-	/* 23: Blue front LED off */
-	/* 24: Inhibit board power off (0 = Disabled, 1 = Enabled) */
-};
-
-#define D2NET_GPIO_INHIBIT_POWER_OFF    24
-
-static void __init d2net_init(void)
-{
-	/*
-	 * Setup basic Orion functions. Need to be called early.
-	 */
-	orion5x_init();
-
-	orion5x_mpp_conf(d2net_mpp_modes);
-
-	/*
-	 * Configure peripherals.
-	 */
-	orion5x_ehci0_init();
-	orion5x_eth_init(&d2net_eth_data);
-	orion5x_i2c_init();
-	orion5x_uart0_init();
-
-	d2net_sata_power_init();
-	orion5x_sata_init(&d2net_sata_data);
-
-	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
-				    ORION_MBUS_DEVBUS_BOOT_ATTR,
-				    D2NET_NOR_BOOT_BASE,
-				    D2NET_NOR_BOOT_SIZE);
-	platform_device_register(&d2net_nor_flash);
-
-	platform_device_register(&d2net_gpio_buttons);
-
-	d2net_gpio_leds_init();
-
-	pr_notice("d2net: Flash write are not yet supported.\n");
-
-	i2c_register_board_info(0, d2net_i2c_devices,
-				ARRAY_SIZE(d2net_i2c_devices));
-
-	orion_gpio_set_valid(D2NET_GPIO_INHIBIT_POWER_OFF, 1);
-}
-
-/* Warning: LaCie use a wrong mach-type (0x20e=526) in their bootloader. */
-
-#ifdef CONFIG_MACH_D2NET
-MACHINE_START(D2NET, "LaCie d2 Network")
-	.atag_offset	= 0x100,
-	.init_machine	= d2net_init,
-	.map_io		= orion5x_map_io,
-	.init_early	= orion5x_init_early,
-	.init_irq	= orion5x_init_irq,
-	.init_time	= orion5x_timer_init,
-	.fixup		= tag_fixup_mem32,
-	.restart	= orion5x_restart,
-MACHINE_END
-#endif
-
-#ifdef CONFIG_MACH_BIGDISK
-MACHINE_START(BIGDISK, "LaCie Big Disk Network")
-	.atag_offset	= 0x100,
-	.init_machine	= d2net_init,
-	.map_io		= orion5x_map_io,
-	.init_early	= orion5x_init_early,
-	.init_irq	= orion5x_init_irq,
-	.init_time	= orion5x_timer_init,
-	.fixup		= tag_fixup_mem32,
-	.restart	= orion5x_restart,
-MACHINE_END
-#endif
-

arch/arm/mach-orion5x/edmini_v2-setup.c

@@ -1,169 +0,0 @@
-/*
- * arch/arm/mach-orion5x/edmini_v2-setup.c
- *
- * LaCie Ethernet Disk mini V2 Setup
- *
- * Copyright (C) 2008 Christopher Moore <moore@free.fr>
- * Copyright (C) 2008 Albert Aribaud <albert.aribaud@free.fr>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-/*
- * TODO: add Orion USB device port init when kernel.org support is added.
- * TODO: add flash write support: see below.
- * TODO: add power-off support.
- * TODO: add I2C EEPROM support.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/pci.h>
-#include <linux/irq.h>
-#include <linux/mbus.h>
-#include <linux/mtd/physmap.h>
-#include <linux/leds.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/i2c.h>
-#include <linux/ata_platform.h>
-#include <linux/gpio.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-#include <mach/orion5x.h>
-#include "common.h"
-#include "mpp.h"
-
-/*****************************************************************************
- * EDMINI_V2 Info
- ****************************************************************************/
-
-/*
- * 512KB NOR flash Device bus boot chip select
- */
-
-#define EDMINI_V2_NOR_BOOT_BASE		0xfff80000
-#define EDMINI_V2_NOR_BOOT_SIZE		SZ_512K
-
-/*****************************************************************************
- * 512KB NOR Flash on BOOT Device
- ****************************************************************************/
-
-/*
- * Currently the MTD code does not recognize the MX29LV400CBCT as a bottom
- * -type device. This could cause risks of accidentally erasing critical
- * flash sectors. We thus define a single, write-protected partition covering
- * the whole flash.
- * TODO: once the flash part TOP/BOTTOM detection issue is sorted out in the MTD
- * code, break this into at least three partitions: 'u-boot code', 'u-boot
- * environment' and 'whatever is left'.
- */
-
-static struct mtd_partition edmini_v2_partitions[] = {
-	{
-		.name		= "Full512kb",
-		.size		= 0x00080000,
-		.offset		= 0x00000000,
-		.mask_flags	= MTD_WRITEABLE,
-	},
-};
-
-static struct physmap_flash_data edmini_v2_nor_flash_data = {
-	.width		= 1,
-	.parts		= edmini_v2_partitions,
-	.nr_parts	= ARRAY_SIZE(edmini_v2_partitions),
-};
-
-static struct resource edmini_v2_nor_flash_resource = {
-	.flags			= IORESOURCE_MEM,
-	.start			= EDMINI_V2_NOR_BOOT_BASE,
-	.end			= EDMINI_V2_NOR_BOOT_BASE
-		+ EDMINI_V2_NOR_BOOT_SIZE - 1,
-};
-
-static struct platform_device edmini_v2_nor_flash = {
-	.name			= "physmap-flash",
-	.id			= 0,
-	.dev		= {
-		.platform_data	= &edmini_v2_nor_flash_data,
-	},
-	.num_resources		= 1,
-	.resource		= &edmini_v2_nor_flash_resource,
-};
-
-/*****************************************************************************
- * RTC 5C372a on I2C bus
- ****************************************************************************/
-
-#define EDMINIV2_RTC_GPIO	3
-
-static struct i2c_board_info __initdata edmini_v2_i2c_rtc = {
-	I2C_BOARD_INFO("rs5c372a", 0x32),
-	.irq = 0,
-};
-
-/*****************************************************************************
- * General Setup
- ****************************************************************************/
-static unsigned int edminiv2_mpp_modes[] __initdata = {
-	MPP0_UNUSED,
-	MPP1_UNUSED,
-	MPP2_UNUSED,
-	MPP3_GPIO,	/* RTC interrupt */
-	MPP4_UNUSED,
-	MPP5_UNUSED,
-	MPP6_UNUSED,
-	MPP7_UNUSED,
-	MPP8_UNUSED,
-	MPP9_UNUSED,
-	MPP10_UNUSED,
-	MPP11_UNUSED,
-	MPP12_SATA_LED,	/* SATA 0 presence */
-	MPP13_SATA_LED,	/* SATA 1 presence */
-	MPP14_SATA_LED,	/* SATA 0 active */
-	MPP15_SATA_LED,	/* SATA 1 active */
-	/* 16: Power LED control (0 = On, 1 = Off) */
-	MPP16_GPIO,
-	/* 17: Power LED control select (0 = CPLD, 1 = GPIO16) */
-	MPP17_GPIO,
-	/* 18: Power button status (0 = Released, 1 = Pressed) */
-	MPP18_GPIO,
-	MPP19_UNUSED,
-	0,
-};
-
-void __init edmini_v2_init(void)
-{
-	orion5x_mpp_conf(edminiv2_mpp_modes);
-
-	/*
-	 * Configure peripherals.
-	 */
-	orion5x_ehci0_init();
-
-	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
-				    ORION_MBUS_DEVBUS_BOOT_ATTR,
-				    EDMINI_V2_NOR_BOOT_BASE,
-				    EDMINI_V2_NOR_BOOT_SIZE);
-	platform_device_register(&edmini_v2_nor_flash);
-
-	pr_notice("edmini_v2: USB device port, flash write and power-off "
-		  "are not yet supported.\n");
-
-	/* Get RTC IRQ and register the chip */
-	if (gpio_request(EDMINIV2_RTC_GPIO, "rtc") == 0) {
-		if (gpio_direction_input(EDMINIV2_RTC_GPIO) == 0)
-			edmini_v2_i2c_rtc.irq = gpio_to_irq(EDMINIV2_RTC_GPIO);
-		else
-			gpio_free(EDMINIV2_RTC_GPIO);
-	}
-
-	if (edmini_v2_i2c_rtc.irq == 0)
-		pr_warning("edmini_v2: failed to get RTC IRQ\n");
-
-	i2c_register_board_info(0, &edmini_v2_i2c_rtc, 1);
-}

arch/arm/mach-orion5x/irq.c

@@ -16,6 +16,7 @@
 #include <mach/bridge-regs.h>
 #include <plat/orion-gpio.h>
 #include <plat/irq.h>
+#include <asm/exception.h>
 #include "common.h"
 
 static int __initdata gpio0_irqs[4] = {
@@ -25,10 +26,37 @@ static int __initdata gpio0_irqs[4] = {
 	IRQ_ORION5X_GPIO_24_31,
 };
 
+#ifdef CONFIG_MULTI_IRQ_HANDLER
+/*
+ * Compiling with both non-DT and DT support enabled, will
+ * break asm irq handler used by non-DT boards. Therefore,
+ * we provide a C-style irq handler even for non-DT boards,
+ * if MULTI_IRQ_HANDLER is set.
+ */
+
+asmlinkage void
+__exception_irq_entry orion5x_legacy_handle_irq(struct pt_regs *regs)
+{
+	u32 stat;
+
+	stat = readl_relaxed(MAIN_IRQ_CAUSE);
+	stat &= readl_relaxed(MAIN_IRQ_MASK);
+	if (stat) {
+		unsigned int hwirq = __fls(stat);
+		handle_IRQ(hwirq, regs);
+		return;
+	}
+}
+#endif
+
 void __init orion5x_init_irq(void)
 {
 	orion_irq_init(0, MAIN_IRQ_MASK);
 
+#ifdef CONFIG_MULTI_IRQ_HANDLER
+	set_handle_irq(orion5x_legacy_handle_irq);
+#endif
+
 	/*
 	 * Initialize gpiolib for GPIOs 0-31.
 	 */

arch/arm/mach-orion5x/mss2-setup.c

@@ -1,274 +0,0 @@
-/*
- * Maxtor Shared Storage II Board Setup
- *
- * Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/pci.h>
-#include <linux/irq.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/leds.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/i2c.h>
-#include <linux/ata_platform.h>
-#include <linux/gpio.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-#include <mach/orion5x.h>
-#include <mach/bridge-regs.h>
-#include "common.h"
-#include "mpp.h"
-
-#define MSS2_NOR_BOOT_BASE	0xff800000
-#define MSS2_NOR_BOOT_SIZE	SZ_256K
-
-/*****************************************************************************
- * Maxtor Shared Storage II Info
- ****************************************************************************/
-
-/*
- * Maxtor Shared Storage II hardware :
- * - Marvell 88F5182-A2 C500
- * - Marvell 88E1111 Gigabit Ethernet PHY
- * - RTC M41T81 (@0x68) on I2C bus
- * - 256KB NOR flash
- * - 64MB of RAM
- */
-
-/*****************************************************************************
- * 256KB NOR Flash on BOOT Device
- ****************************************************************************/
-
-static struct physmap_flash_data mss2_nor_flash_data = {
-	.width		= 1,
-};
-
-static struct resource mss2_nor_flash_resource = {
-	.flags		= IORESOURCE_MEM,
-	.start		= MSS2_NOR_BOOT_BASE,
-	.end		= MSS2_NOR_BOOT_BASE + MSS2_NOR_BOOT_SIZE - 1,
-};
-
-static struct platform_device mss2_nor_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &mss2_nor_flash_data,
-	},
-	.resource	= &mss2_nor_flash_resource,
-	.num_resources	= 1,
-};
-
-/****************************************************************************
- * PCI setup
- ****************************************************************************/
-static int __init mss2_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
-	int irq;
-
-	/*
-	 * Check for devices with hard-wired IRQs.
-	 */
-	irq = orion5x_pci_map_irq(dev, slot, pin);
-	if (irq != -1)
-		return irq;
-
-	return -1;
-}
-
-static struct hw_pci mss2_pci __initdata = {
-	.nr_controllers = 2,
-	.setup		= orion5x_pci_sys_setup,
-	.scan		= orion5x_pci_sys_scan_bus,
-	.map_irq	= mss2_pci_map_irq,
-};
-
-static int __init mss2_pci_init(void)
-{
-	if (machine_is_mss2())
-		pci_common_init(&mss2_pci);
-
-	return 0;
-}
-subsys_initcall(mss2_pci_init);
-
-
-/*****************************************************************************
- * Ethernet
- ****************************************************************************/
-
-static struct mv643xx_eth_platform_data mss2_eth_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-/*****************************************************************************
- * SATA
- ****************************************************************************/
-
-static struct mv_sata_platform_data mss2_sata_data = {
-	.n_ports	= 2,
-};
-
-/*****************************************************************************
- * GPIO buttons
- ****************************************************************************/
-
-#define MSS2_GPIO_KEY_RESET	12
-#define MSS2_GPIO_KEY_POWER	11
-
-static struct gpio_keys_button mss2_buttons[] = {
-	{
-		.code		= KEY_POWER,
-		.gpio		= MSS2_GPIO_KEY_POWER,
-		.desc		= "Power",
-		.active_low	= 1,
-	}, {
-		.code		= KEY_RESTART,
-		.gpio		= MSS2_GPIO_KEY_RESET,
-		.desc		= "Reset",
-		.active_low	= 1,
-	},
-};
-
-static struct gpio_keys_platform_data mss2_button_data = {
-	.buttons	= mss2_buttons,
-	.nbuttons	= ARRAY_SIZE(mss2_buttons),
-};
-
-static struct platform_device mss2_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &mss2_button_data,
-	},
-};
-
-/*****************************************************************************
- * RTC m41t81 on I2C bus
- ****************************************************************************/
-
-#define MSS2_GPIO_RTC_IRQ	3
-
-static struct i2c_board_info __initdata mss2_i2c_rtc = {
-	I2C_BOARD_INFO("m41t81", 0x68),
-};
-
-/*****************************************************************************
- * MSS2 power off method
- ****************************************************************************/
-/*
- * On the Maxtor Shared Storage II, the shutdown process is the following :
- * - Userland modifies U-boot env to tell U-boot to go idle at next boot
- * - The board reboots
- * - U-boot starts and go into an idle mode until the user press "power"
- */
-static void mss2_power_off(void)
-{
-	u32 reg;
-
-	/*
-	 * Enable and issue soft reset
-	 */
-	reg = readl(RSTOUTn_MASK);
-	reg |= 1 << 2;
-	writel(reg, RSTOUTn_MASK);
-
-	reg = readl(CPU_SOFT_RESET);
-	reg |= 1;
-	writel(reg, CPU_SOFT_RESET);
-}
-
-/****************************************************************************
- * General Setup
- ****************************************************************************/
-static unsigned int mss2_mpp_modes[] __initdata = {
-	MPP0_GPIO,		/* Power LED */
-	MPP1_GPIO,		/* Error LED */
-	MPP2_UNUSED,
-	MPP3_GPIO,		/* RTC interrupt */
-	MPP4_GPIO,		/* HDD ind. (Single/Dual)*/
-	MPP5_GPIO,		/* HD0 5V control */
-	MPP6_GPIO,		/* HD0 12V control */
-	MPP7_GPIO,		/* HD1 5V control */
-	MPP8_GPIO,		/* HD1 12V control */
-	MPP9_UNUSED,
-	MPP10_GPIO,		/* Fan control */
-	MPP11_GPIO,		/* Power button */
-	MPP12_GPIO,		/* Reset button */
-	MPP13_UNUSED,
-	MPP14_SATA_LED,		/* SATA 0 active */
-	MPP15_SATA_LED,		/* SATA 1 active */
-	MPP16_UNUSED,
-	MPP17_UNUSED,
-	MPP18_UNUSED,
-	MPP19_UNUSED,
-	0,
-};
-
-static void __init mss2_init(void)
-{
-	/* Setup basic Orion functions. Need to be called early. */
-	orion5x_init();
-
-	orion5x_mpp_conf(mss2_mpp_modes);
-
-	/*
-	 * MPP[20] Unused
-	 * MPP[21] PCI clock
-	 * MPP[22] USB 0 over current
-	 * MPP[23] USB 1 over current
-	 */
-
-	/*
-	 * Configure peripherals.
-	 */
-	orion5x_ehci0_init();
-	orion5x_ehci1_init();
-	orion5x_eth_init(&mss2_eth_data);
-	orion5x_i2c_init();
-	orion5x_sata_init(&mss2_sata_data);
-	orion5x_uart0_init();
-	orion5x_xor_init();
-
-	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
-				    ORION_MBUS_DEVBUS_BOOT_ATTR,
-				    MSS2_NOR_BOOT_BASE,
-				    MSS2_NOR_BOOT_SIZE);
-	platform_device_register(&mss2_nor_flash);
-
-	platform_device_register(&mss2_button_device);
-
-	if (gpio_request(MSS2_GPIO_RTC_IRQ, "rtc") == 0) {
-		if (gpio_direction_input(MSS2_GPIO_RTC_IRQ) == 0)
-			mss2_i2c_rtc.irq = gpio_to_irq(MSS2_GPIO_RTC_IRQ);
-		else
-			gpio_free(MSS2_GPIO_RTC_IRQ);
-	}
-	i2c_register_board_info(0, &mss2_i2c_rtc, 1);
-
-	/* register mss2 specific power-off method */
-	pm_power_off = mss2_power_off;
-}
-
-MACHINE_START(MSS2, "Maxtor Shared Storage II")
-	/* Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com> */
-	.atag_offset	= 0x100,
-	.init_machine	= mss2_init,
-	.map_io		= orion5x_map_io,
-	.init_early	= orion5x_init_early,
-	.init_irq	= orion5x_init_irq,
-	.init_time	= orion5x_timer_init,
-	.fixup		= tag_fixup_mem32,
-	.restart	= orion5x_restart,
-MACHINE_END

arch/arm/plat-orion/gpio.c

@@ -597,51 +597,3 @@ void __init orion_gpio_init(struct device_node *np,
 
 	orion_gpio_chip_count++;
 }
-
-#ifdef CONFIG_OF
-static void __init orion_gpio_of_init_one(struct device_node *np,
-					  int irq_gpio_base)
-{
-	int ngpio, gpio_base, mask_offset;
-	void __iomem *base;
-	int ret, i;
-	int irqs[4];
-	int secondary_irq_base;
-
-	ret = of_property_read_u32(np, "ngpio", &ngpio);
-	if (ret)
-		goto out;
-	ret = of_property_read_u32(np, "mask-offset", &mask_offset);
-	if (ret == -EINVAL)
-		mask_offset = 0;
-	else
-		goto out;
-	base = of_iomap(np, 0);
-	if (!base)
-		goto out;
-
-	secondary_irq_base = irq_gpio_base + (32 * orion_gpio_chip_count);
-	gpio_base = 32 * orion_gpio_chip_count;
-
-	/* Get the interrupt numbers. Each chip can have up to 4
-	 * interrupt handlers, with each handler dealing with 8 GPIO
-	 * pins. */
-
-	for (i = 0; i < 4; i++)
-		irqs[i] = irq_of_parse_and_map(np, i);
-
-	orion_gpio_init(np, gpio_base, ngpio, base, mask_offset,
-			secondary_irq_base, irqs);
-	return;
-out:
-	pr_err("%s: %s: missing mandatory property\n", __func__, np->name);
-}
-
-void __init orion_gpio_of_init(int irq_gpio_base)
-{
-	struct device_node *np;
-
-	for_each_compatible_node(np, NULL, "marvell,orion-gpio")
-		orion_gpio_of_init_one(np, irq_gpio_base);
-}
-#endif

arch/arm/plat-orion/include/plat/irq.h

@@ -12,5 +12,4 @@
 #define __PLAT_IRQ_H
 
 void orion_irq_init(unsigned int irq_start, void __iomem *maskaddr);
-void __init orion_dt_init_irq(void);
 #endif

arch/arm/plat-orion/include/plat/orion-gpio.h

@@ -33,5 +33,4 @@ void __init orion_gpio_init(struct device_node *np,
 			    int secondary_irq_base,
 			    int irq[4]);
 
-void __init orion_gpio_of_init(int irq_gpio_base);
 #endif

arch/arm/plat-orion/irq.c

@@ -20,47 +20,6 @@
 #include <plat/orion-gpio.h>
 #include <mach/bridge-regs.h>
 
-#ifdef CONFIG_MULTI_IRQ_HANDLER
-/*
- * Compiling with both non-DT and DT support enabled, will
- * break asm irq handler used by non-DT boards. Therefore,
- * we provide a C-style irq handler even for non-DT boards,
- * if MULTI_IRQ_HANDLER is set.
- *
- * Notes:
- * - this is prepared for Kirkwood and Dove only, update
- *   accordingly if you add Orion5x or MV78x00.
- * - Orion5x uses different macro names and has only one
- *   set of CAUSE/MASK registers.
- * - MV78x00 uses the same macro names but has a third
- *   set of CAUSE/MASK registers.
- *
- */
-
-static void __iomem *orion_irq_base = IRQ_VIRT_BASE;
-
-asmlinkage void
-__exception_irq_entry orion_legacy_handle_irq(struct pt_regs *regs)
-{
-	u32 stat;
-
-	stat = readl_relaxed(orion_irq_base + IRQ_CAUSE_LOW_OFF);
-	stat &= readl_relaxed(orion_irq_base + IRQ_MASK_LOW_OFF);
-	if (stat) {
-		unsigned int hwirq = __fls(stat);
-		handle_IRQ(hwirq, regs);
-		return;
-	}
-	stat = readl_relaxed(orion_irq_base + IRQ_CAUSE_HIGH_OFF);
-	stat &= readl_relaxed(orion_irq_base + IRQ_MASK_HIGH_OFF);
-	if (stat) {
-		unsigned int hwirq = 32 + __fls(stat);
-		handle_IRQ(hwirq, regs);
-		return;
-	}
-}
-#endif
-
 void __init orion_irq_init(unsigned int irq_start, void __iomem *maskaddr)
 {
 	struct irq_chip_generic *gc;
@@ -78,40 +37,4 @@ void __init orion_irq_init(unsigned int irq_start, void __iomem *maskaddr)
 	ct->chip.irq_unmask = irq_gc_mask_set_bit;
 	irq_setup_generic_chip(gc, IRQ_MSK(32), IRQ_GC_INIT_MASK_CACHE,
 			       IRQ_NOREQUEST, IRQ_LEVEL | IRQ_NOPROBE);
-
-#ifdef CONFIG_MULTI_IRQ_HANDLER
-	set_handle_irq(orion_legacy_handle_irq);
-#endif
-}
-
-#ifdef CONFIG_OF
-static int __init orion_add_irq_domain(struct device_node *np,
-				       struct device_node *interrupt_parent)
-{
-	int i = 0;
-	void __iomem *base;
-
-	do {
-		base = of_iomap(np, i);
-		if (base) {
-			orion_irq_init(i * 32, base + 0x04);
-			i++;
-		}
-	} while (base);
-
-	irq_domain_add_legacy(np, i * 32, 0, 0,
-			      &irq_domain_simple_ops, NULL);
-	return 0;
-}
-
-static const struct of_device_id orion_irq_match[] = {
-	{ .compatible = "marvell,orion-intc",
-	  .data = orion_add_irq_domain, },
-	{},
-};
-
-void __init orion_dt_init_irq(void)
-{
-	of_irq_init(orion_irq_match);
 }
-#endif