Merge 4.17-rc6 into usb-next

We want the bug fixes and this resolves the merge issues with the usbip
driver.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/ABI/testing/sysfs-class-cxl

@@ -244,3 +244,11 @@ Description:    read only
                 Returns 1 if the psl timebase register is synchronized
                 with the core timebase register, 0 otherwise.
 Users:          https://github.com/ibm-capi/libcxl
+
+What:           /sys/class/cxl/<card>/tunneled_ops_supported
+Date:           May 2018
+Contact:        linuxppc-dev@lists.ozlabs.org
+Description:    read only
+                Returns 1 if tunneled operations are supported in capi mode,
+                0 otherwise.
+Users:          https://github.com/ibm-capi/libcxl

Documentation/admin-guide/pm/intel_pstate.rst

@@ -145,7 +145,7 @@ feature enabled.]
 
 In this mode ``intel_pstate`` registers utilization update callbacks with the
 CPU scheduler in order to run a P-state selection algorithm, either
-``powersave`` or ``performance``, depending on the ``scaling_cur_freq`` policy
+``powersave`` or ``performance``, depending on the ``scaling_governor`` policy
 setting in ``sysfs``.  The current CPU frequency information to be made
 available from the ``scaling_cur_freq`` policy attribute in ``sysfs`` is
 periodically updated by those utilization update callbacks too.

Documentation/admin-guide/pm/sleep-states.rst

@@ -15,7 +15,7 @@ Sleep States That Can Be Supported
 ==================================
 
 Depending on its configuration and the capabilities of the platform it runs on,
-the Linux kernel can support up to four system sleep states, includig
+the Linux kernel can support up to four system sleep states, including
 hibernation and up to three variants of system suspend.  The sleep states that
 can be supported by the kernel are listed below.
 

Documentation/device-mapper/thin-provisioning.txt

@@ -264,7 +264,10 @@ i) Constructor
 			   data device, but just remove the mapping.
 
       read_only: Don't allow any changes to be made to the pool
-		 metadata.
+		 metadata.  This mode is only available after the
+		 thin-pool has been created and first used in full
+		 read/write mode.  It cannot be specified on initial
+		 thin-pool creation.
 
       error_if_no_space: Error IOs, instead of queueing, if no space.
 

Documentation/devicetree/bindings/ata/ahci-platform.txt

@@ -30,7 +30,6 @@ compatible:
 Optional properties:
 - dma-coherent      : Present if dma operations are coherent
 - clocks            : a list of phandle + clock specifier pairs
-- resets            : a list of phandle + reset specifier pairs
 - target-supply     : regulator for SATA target power
 - phys              : reference to the SATA PHY node
 - phy-names         : must be "sata-phy"

Documentation/devicetree/bindings/display/panel/panel-common.txt

@@ -38,7 +38,7 @@ Display Timings
   require specific display timings. The panel-timing subnode expresses those
   timings as specified in the timing subnode section of the display timing
   bindings defined in
-  Documentation/devicetree/bindings/display/display-timing.txt.
+  Documentation/devicetree/bindings/display/panel/display-timing.txt.
 
 
 Connectivity

Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt

@@ -26,6 +26,7 @@ Required Properties:
 		- "renesas,dmac-r8a7794" (R-Car E2)
 		- "renesas,dmac-r8a7795" (R-Car H3)
 		- "renesas,dmac-r8a7796" (R-Car M3-W)
+		- "renesas,dmac-r8a77965" (R-Car M3-N)
 		- "renesas,dmac-r8a77970" (R-Car V3M)
 		- "renesas,dmac-r8a77980" (R-Car V3H)
 

Documentation/devicetree/bindings/net/can/rcar_canfd.txt

@@ -5,7 +5,9 @@ Required properties:
 - compatible: Must contain one or more of the following:
   - "renesas,rcar-gen3-canfd" for R-Car Gen3 compatible controller.
   - "renesas,r8a7795-canfd" for R8A7795 (R-Car H3) compatible controller.
-  - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3) compatible controller.
+  - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3-W) compatible controller.
+  - "renesas,r8a77970-canfd" for R8A77970 (R-Car V3M) compatible controller.
+  - "renesas,r8a77980-canfd" for R8A77980 (R-Car V3H) compatible controller.
 
   When compatible with the generic version, nodes must list the
   SoC-specific version corresponding to the platform first, followed by the

Documentation/devicetree/bindings/net/marvell-pp2.txt

@@ -21,9 +21,10 @@ Required properties:
 	- main controller clock (for both armada-375-pp2 and armada-7k-pp2)
 	- GOP clock (for both armada-375-pp2 and armada-7k-pp2)
 	- MG clock (only for armada-7k-pp2)
+	- MG Core clock (only for armada-7k-pp2)
 	- AXI clock (only for armada-7k-pp2)
-- clock-names: names of used clocks, must be "pp_clk", "gop_clk", "mg_clk"
-  and "axi_clk" (the 2 latter only for armada-7k-pp2).
+- clock-names: names of used clocks, must be "pp_clk", "gop_clk", "mg_clk",
+  "mg_core_clk" and "axi_clk" (the 3 latter only for armada-7k-pp2).
 
 The ethernet ports are represented by subnodes. At least one port is
 required.
@@ -80,8 +81,8 @@ cpm_ethernet: ethernet@0 {
 	compatible = "marvell,armada-7k-pp22";
 	reg = <0x0 0x100000>, <0x129000 0xb000>;
 	clocks = <&cpm_syscon0 1 3>, <&cpm_syscon0 1 9>,
-		 <&cpm_syscon0 1 5>, <&cpm_syscon0 1 18>;
-	clock-names = "pp_clk", "gop_clk", "gp_clk", "axi_clk";
+		 <&cpm_syscon0 1 5>, <&cpm_syscon0 1 6>, <&cpm_syscon0 1 18>;
+	clock-names = "pp_clk", "gop_clk", "mg_clk", "mg_core_clk", "axi_clk";
 
 	eth0: eth0 {
 		interrupts = <ICU_GRP_NSR 39 IRQ_TYPE_LEVEL_HIGH>,

Documentation/devicetree/bindings/net/renesas,ravb.txt

@@ -18,6 +18,7 @@ Required properties:
 
       - "renesas,etheravb-r8a7795" for the R8A7795 SoC.
       - "renesas,etheravb-r8a7796" for the R8A7796 SoC.
+      - "renesas,etheravb-r8a77965" for the R8A77965 SoC.
       - "renesas,etheravb-r8a77970" for the R8A77970 SoC.
       - "renesas,etheravb-r8a77980" for the R8A77980 SoC.
       - "renesas,etheravb-r8a77995" for the R8A77995 SoC.

Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt

@@ -56,9 +56,9 @@ pins it needs, and how they should be configured, with regard to muxer
 configuration, drive strength and pullups. If one of these options is
 not set, its actual value will be unspecified.
 
-This driver supports the generic pin multiplexing and configuration
-bindings. For details on each properties, you can refer to
-./pinctrl-bindings.txt.
+Allwinner A1X Pin Controller supports the generic pin multiplexing and
+configuration bindings. For details on each properties, you can refer to
+ ./pinctrl-bindings.txt.
 
 Required sub-node properties:
   - pins

Documentation/devicetree/bindings/serial/renesas,sci-serial.txt

@@ -43,6 +43,8 @@ Required properties:
     - "renesas,hscif-r8a7795" for R8A7795 (R-Car H3) HSCIF compatible UART.
     - "renesas,scif-r8a7796" for R8A7796 (R-Car M3-W) SCIF compatible UART.
     - "renesas,hscif-r8a7796" for R8A7796 (R-Car M3-W) HSCIF compatible UART.
+    - "renesas,scif-r8a77965" for R8A77965 (R-Car M3-N) SCIF compatible UART.
+    - "renesas,hscif-r8a77965" for R8A77965 (R-Car M3-N) HSCIF compatible UART.
     - "renesas,scif-r8a77970" for R8A77970 (R-Car V3M) SCIF compatible UART.
     - "renesas,hscif-r8a77970" for R8A77970 (R-Car V3M) HSCIF compatible UART.
     - "renesas,scif-r8a77980" for R8A77980 (R-Car V3H) SCIF compatible UART.

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -182,6 +182,7 @@ karo	Ka-Ro electronics GmbH
 keithkoep	Keith & Koep GmbH
 keymile	Keymile GmbH
 khadas	Khadas
+kiebackpeter    Kieback & Peter GmbH
 kinetic Kinetic Technologies
 kingnovel	Kingnovel Technology Co., Ltd.
 kosagi	Sutajio Ko-Usagi PTE Ltd.

Documentation/devicetree/overlay-notes.txt

@@ -98,6 +98,14 @@ Finally, if you need to remove all overlays in one-go, just call
 of_overlay_remove_all() which will remove every single one in the correct
 order.
 
+In addition, there is the option to register notifiers that get called on
+overlay operations. See of_overlay_notifier_register/unregister and
+enum of_overlay_notify_action for details.
+
+Note that a notifier callback is not supposed to store pointers to a device
+tree node or its content beyond OF_OVERLAY_POST_REMOVE corresponding to the
+respective node it received.
+
 Overlay DTS Format
 ------------------
 

Documentation/virtual/kvm/cpuid.txt

@@ -72,8 +72,8 @@ KVM_FEATURE_CLOCKSOURCE_STABLE_BIT ||    24 || host will warn if no guest-side
 
 flag                               || value || meaning
 ==================================================================================
-KVM_HINTS_DEDICATED                ||     0 || guest checks this feature bit to
-                                   ||       || determine if there is vCPU pinning
-                                   ||       || and there is no vCPU over-commitment,
+KVM_HINTS_REALTIME                 ||     0 || guest checks this feature bit to
+                                   ||       || determine that vCPUs are never
+                                   ||       || preempted for an unlimited time,
                                    ||       || allowing optimizations
 ----------------------------------------------------------------------------------

MAINTAINERS

@@ -137,9 +137,9 @@ Maintainers List (try to look for most precise areas first)
 		-----------------------------------
 
 3C59X NETWORK DRIVER
-M:	Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
+M:	Steffen Klassert <klassert@kernel.org>
 L:	netdev@vger.kernel.org
-S:	Maintained
+S:	Odd Fixes
 F:	Documentation/networking/vortex.txt
 F:	drivers/net/ethernet/3com/3c59x.c
 
@@ -3691,7 +3691,6 @@ F:	drivers/cpufreq/arm_big_little_dt.c
 
 CPU POWER MONITORING SUBSYSTEM
 M:	Thomas Renninger <trenn@suse.com>
-M:	Shuah Khan <shuahkh@osg.samsung.com>
 M:	Shuah Khan <shuah@kernel.org>
 L:	linux-pm@vger.kernel.org
 S:	Maintained
@@ -4310,7 +4309,7 @@ F:	Documentation/driver-api/dma-buf.rst
 T:	git git://anongit.freedesktop.org/drm/drm-misc
 
 DMA GENERIC OFFLOAD ENGINE SUBSYSTEM
-M:	Vinod Koul <vinod.koul@intel.com>
+M:	Vinod Koul <vkoul@kernel.org>
 L:	dmaengine@vger.kernel.org
 Q:	https://patchwork.kernel.org/project/linux-dmaengine/list/
 S:	Maintained
@@ -7696,10 +7695,10 @@ F:	include/linux/sunrpc/
 F:	include/uapi/linux/sunrpc/
 
 KERNEL SELFTEST FRAMEWORK
-M:	Shuah Khan <shuahkh@osg.samsung.com>
 M:	Shuah Khan <shuah@kernel.org>
 L:	linux-kselftest@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest.git
+Q:	https://patchwork.kernel.org/project/linux-kselftest/list/
 S:	Maintained
 F:	tools/testing/selftests/
 F:	Documentation/dev-tools/kselftest*
@@ -9873,7 +9872,7 @@ F:	include/linux/platform_data/nxp-nci.h
 F:	Documentation/devicetree/bindings/net/nfc/
 
 NFS, SUNRPC, AND LOCKD CLIENTS
-M:	Trond Myklebust <trond.myklebust@primarydata.com>
+M:	Trond Myklebust <trond.myklebust@hammerspace.com>
 M:	Anna Schumaker <anna.schumaker@netapp.com>
 L:	linux-nfs@vger.kernel.org
 W:	http://client.linux-nfs.org
@@ -12223,7 +12222,7 @@ F:	Documentation/s390/vfio-ccw.txt
 F:	include/uapi/linux/vfio_ccw.h
 
 S390 ZCRYPT DRIVER
-M:	Harald Freudenberger <freude@de.ibm.com>
+M:	Harald Freudenberger <freude@linux.ibm.com>
 L:	linux-s390@vger.kernel.org
 W:	http://www.ibm.com/developerworks/linux/linux390/
 S:	Supported
@@ -13267,6 +13266,12 @@ M:	Jan-Benedict Glaw <jbglaw@lug-owl.de>
 S:	Maintained
 F:	arch/alpha/kernel/srm_env.c
 
+ST STM32 I2C/SMBUS DRIVER
+M:	Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
+L:	linux-i2c@vger.kernel.org
+S:	Maintained
+F:	drivers/i2c/busses/i2c-stm32*
+
 STABLE BRANCH
 M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 L:	stable@vger.kernel.org
@@ -14651,7 +14656,6 @@ F:	drivers/usb/common/usb-otg-fsm.c
 
 USB OVER IP DRIVER
 M:	Valentina Manea <valentina.manea.m@gmail.com>
-M:	Shuah Khan <shuahkh@osg.samsung.com>
 M:	Shuah Khan <shuah@kernel.org>
 L:	linux-usb@vger.kernel.org
 S:	Maintained

Makefile

@@ -2,7 +2,7 @@
 VERSION = 4
 PATCHLEVEL = 17
 SUBLEVEL = 0
-EXTRAVERSION = -rc4
+EXTRAVERSION = -rc6
 NAME = Merciless Moray
 
 # *DOCUMENTATION*

arch/Kconfig

@@ -464,6 +464,10 @@ config GCC_PLUGIN_LATENT_ENTROPY
 config GCC_PLUGIN_STRUCTLEAK
 	bool "Force initialization of variables containing userspace addresses"
 	depends on GCC_PLUGINS
+	# Currently STRUCTLEAK inserts initialization out of live scope of
+	# variables from KASAN point of view. This leads to KASAN false
+	# positive reports. Prohibit this combination for now.
+	depends on !KASAN_EXTRA
 	help
 	  This plugin zero-initializes any structures containing a
 	  __user attribute. This can prevent some classes of information

arch/arm/boot/compressed/Makefile

@@ -117,11 +117,9 @@ ccflags-y := -fpic -mno-single-pic-base -fno-builtin -I$(obj)
 asflags-y := -DZIMAGE
 
 # Supply kernel BSS size to the decompressor via a linker symbol.
-KBSS_SZ = $(shell $(CROSS_COMPILE)nm $(obj)/../../../../vmlinux | \
-		perl -e 'while (<>) { \
-			$$bss_start=hex($$1) if /^([[:xdigit:]]+) B __bss_start$$/; \
-			$$bss_end=hex($$1) if /^([[:xdigit:]]+) B __bss_stop$$/; \
-		}; printf "%d\n", $$bss_end - $$bss_start;')
+KBSS_SZ = $(shell echo $$(($$($(CROSS_COMPILE)nm $(obj)/../../../../vmlinux | \
+		sed -n -e 's/^\([^ ]*\) [AB] __bss_start$$/-0x\1/p' \
+		       -e 's/^\([^ ]*\) [AB] __bss_stop$$/+0x\1/p') )) )
 LDFLAGS_vmlinux = --defsym _kernel_bss_size=$(KBSS_SZ)
 # Supply ZRELADDR to the decompressor via a linker symbol.
 ifneq ($(CONFIG_AUTO_ZRELADDR),y)

arch/arm/boot/compressed/head.S

@@ -29,19 +29,19 @@
 #if defined(CONFIG_DEBUG_ICEDCC)
 
 #if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_V6K) || defined(CONFIG_CPU_V7)
-		.macro	loadsp, rb, tmp
+		.macro	loadsp, rb, tmp1, tmp2
 		.endm
 		.macro	writeb, ch, rb
 		mcr	p14, 0, \ch, c0, c5, 0
 		.endm
 #elif defined(CONFIG_CPU_XSCALE)
-		.macro	loadsp, rb, tmp
+		.macro	loadsp, rb, tmp1, tmp2
 		.endm
 		.macro	writeb, ch, rb
 		mcr	p14, 0, \ch, c8, c0, 0
 		.endm
 #else
-		.macro	loadsp, rb, tmp
+		.macro	loadsp, rb, tmp1, tmp2
 		.endm
 		.macro	writeb, ch, rb
 		mcr	p14, 0, \ch, c1, c0, 0
@@ -57,7 +57,7 @@
 		.endm
 
 #if defined(CONFIG_ARCH_SA1100)
-		.macro	loadsp, rb, tmp
+		.macro	loadsp, rb, tmp1, tmp2
 		mov	\rb, #0x80000000	@ physical base address
 #ifdef CONFIG_DEBUG_LL_SER3
 		add	\rb, \rb, #0x00050000	@ Ser3
@@ -66,8 +66,8 @@
 #endif
 		.endm
 #else
-		.macro	loadsp,	rb, tmp
-		addruart \rb, \tmp
+		.macro	loadsp,	rb, tmp1, tmp2
+		addruart \rb, \tmp1, \tmp2
 		.endm
 #endif
 #endif
@@ -561,8 +561,6 @@ not_relocated:	mov	r0, #0
 		bl	decompress_kernel
 		bl	cache_clean_flush
 		bl	cache_off
-		mov	r1, r7			@ restore architecture number
-		mov	r2, r8			@ restore atags pointer
 
 #ifdef CONFIG_ARM_VIRT_EXT
 		mrs	r0, spsr		@ Get saved CPU boot mode
@@ -1297,7 +1295,7 @@ phex:		adr	r3, phexbuf
 		b	1b
 
 @ puts corrupts {r0, r1, r2, r3}
-puts:		loadsp	r3, r1
+puts:		loadsp	r3, r2, r1
 1:		ldrb	r2, [r0], #1
 		teq	r2, #0
 		moveq	pc, lr
@@ -1314,8 +1312,8 @@ puts:		loadsp	r3, r1
 @ putc corrupts {r0, r1, r2, r3}
 putc:
 		mov	r2, r0
+		loadsp	r3, r1, r0
 		mov	r0, #0
-		loadsp	r3, r1
 		b	2b
 
 @ memdump corrupts {r0, r1, r2, r3, r10, r11, r12, lr}
@@ -1365,6 +1363,8 @@ __hyp_reentry_vectors:
 
 __enter_kernel:
 		mov	r0, #0			@ must be 0
+		mov	r1, r7			@ restore architecture number
+		mov	r2, r8			@ restore atags pointer
  ARM(		mov	pc, r4		)	@ call kernel
  M_CLASS(	add	r4, r4, #1	)	@ enter in Thumb mode for M class
  THUMB(		bx	r4		)	@ entry point is always ARM for A/R classes

arch/arm/boot/dts/bcm-cygnus.dtsi

@@ -69,7 +69,7 @@
 		timer@20200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x20200 0x100>;
-			interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_PPI 11 IRQ_TYPE_EDGE_RISING>;
 			clocks = <&periph_clk>;
 		};
 

arch/arm/boot/dts/da850-lcdk.dts

@@ -21,8 +21,8 @@
 		stdout-path = "serial2:115200n8";
 	};
 
-	memory {
-		device_type = "memory";
+	memory@c0000000 {
+		/* 128 MB DDR2 SDRAM @ 0xc0000000 */
 		reg = <0xc0000000 0x08000000>;
 	};
 

arch/arm/boot/dts/da850.dtsi

@@ -7,10 +7,19 @@
  * Free Software Foundation;  either version 2 of the  License, or (at your
  * option) any later version.
  */
-#include "skeleton.dtsi"
 #include <dt-bindings/interrupt-controller/irq.h>
 
 / {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	chosen { };
+	aliases { };
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x0>;
+	};
+
 	arm {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -46,8 +55,6 @@
 		pmx_core: pinmux@14120 {
 			compatible = "pinctrl-single";
 			reg = <0x14120 0x50>;
-			#address-cells = <1>;
-			#size-cells = <0>;
 			#pinctrl-cells = <2>;
 			pinctrl-single,bit-per-mux;
 			pinctrl-single,register-width = <32>;

arch/arm/boot/dts/dm8148-evm.dts

@@ -10,7 +10,7 @@
 
 / {
 	model = "DM8148 EVM";
-	compatible = "ti,dm8148-evm", "ti,dm8148";
+	compatible = "ti,dm8148-evm", "ti,dm8148", "ti,dm814";
 
 	memory@80000000 {
 		device_type = "memory";

arch/arm/boot/dts/dm8148-t410.dts

@@ -9,7 +9,7 @@
 
 / {
 	model = "HP t410 Smart Zero Client";
-	compatible = "hp,t410", "ti,dm8148";
+	compatible = "hp,t410", "ti,dm8148", "ti,dm814";
 
 	memory@80000000 {
 		device_type = "memory";

arch/arm/boot/dts/dm8168-evm.dts

@@ -10,7 +10,7 @@
 
 / {
 	model = "DM8168 EVM";
-	compatible = "ti,dm8168-evm", "ti,dm8168";
+	compatible = "ti,dm8168-evm", "ti,dm8168", "ti,dm816";
 
 	memory@80000000 {
 		device_type = "memory";

arch/arm/boot/dts/dra62x-j5eco-evm.dts

@@ -10,7 +10,7 @@
 
 / {
 	model = "DRA62x J5 Eco EVM";
-	compatible = "ti,dra62x-j5eco-evm", "ti,dra62x", "ti,dm8148";
+	compatible = "ti,dra62x-j5eco-evm", "ti,dra62x", "ti,dm8148", "ti,dm814";
 
 	memory@80000000 {
 		device_type = "memory";

arch/arm/boot/dts/imx35.dtsi

@@ -303,7 +303,7 @@
 			};
 
 			can1: can@53fe4000 {
-				compatible = "fsl,imx35-flexcan";
+				compatible = "fsl,imx35-flexcan", "fsl,imx25-flexcan";
 				reg = <0x53fe4000 0x1000>;
 				clocks = <&clks 33>, <&clks 33>;
 				clock-names = "ipg", "per";
@@ -312,7 +312,7 @@
 			};
 
 			can2: can@53fe8000 {
-				compatible = "fsl,imx35-flexcan";
+				compatible = "fsl,imx35-flexcan", "fsl,imx25-flexcan";
 				reg = <0x53fe8000 0x1000>;
 				clocks = <&clks 34>, <&clks 34>;
 				clock-names = "ipg", "per";

arch/arm/boot/dts/imx51-zii-rdu1.dts

@@ -523,7 +523,7 @@
 	};
 
 	touchscreen@20 {
-		compatible = "syna,rmi4_i2c";
+		compatible = "syna,rmi4-i2c";
 		reg = <0x20>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_ts>;
@@ -541,8 +541,8 @@
 
 		rmi4-f11@11 {
 			reg = <0x11>;
-			touch-inverted-y;
-			touch-swapped-x-y;
+			touchscreen-inverted-y;
+			touchscreen-swapped-x-y;
 			syna,sensor-type = <1>;
 		};
 	};

arch/arm/boot/dts/imx53.dtsi

@@ -551,7 +551,7 @@
 			};
 
 			can1: can@53fc8000 {
-				compatible = "fsl,imx53-flexcan";
+				compatible = "fsl,imx53-flexcan", "fsl,imx25-flexcan";
 				reg = <0x53fc8000 0x4000>;
 				interrupts = <82>;
 				clocks = <&clks IMX5_CLK_CAN1_IPG_GATE>,
@@ -561,7 +561,7 @@
 			};
 
 			can2: can@53fcc000 {
-				compatible = "fsl,imx53-flexcan";
+				compatible = "fsl,imx53-flexcan", "fsl,imx25-flexcan";
 				reg = <0x53fcc000 0x4000>;
 				interrupts = <83>;
 				clocks = <&clks IMX5_CLK_CAN2_IPG_GATE>,

arch/arm/boot/dts/imx7s.dtsi

@@ -868,6 +868,7 @@
 
 			crypto: caam@30900000 {
 				compatible = "fsl,sec-v4.0";
+				fsl,sec-era = <8>;
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0x30900000 0x40000>;

arch/arm/boot/dts/logicpd-som-lv.dtsi

@@ -26,7 +26,7 @@
 		gpio = <&gpio1 3 0>;   /* gpio_3 */
 		startup-delay-us = <70000>;
 		enable-active-high;
-		vin-supply = <&vmmc2>;
+		vin-supply = <&vaux3>;
 	};
 
 	/* HS USB Host PHY on PORT 1 */
@@ -82,6 +82,7 @@
 		twl_audio: audio {
 			compatible = "ti,twl4030-audio";
 			codec {
+				ti,hs_extmute_gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
 			};
 		};
 	};
@@ -199,6 +200,7 @@
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0)        /* i2c1_scl.i2c1_scl */
 			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0)        /* i2c1_sda.i2c1_sda */
+			OMAP3_CORE1_IOPAD(0x20ba, PIN_OUTPUT | MUX_MODE4)        /* gpmc_ncs6.gpio_57 */
 		>;
 	};
 };
@@ -213,7 +215,7 @@
 	};
 	wl127x_gpio: pinmux_wl127x_gpio_pin {
 		pinctrl-single,pins = <
-			OMAP3_WKUP_IOPAD(0x2a0c, PIN_INPUT | MUX_MODE4)		/* sys_boot0.gpio_2 */
+			OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT | MUX_MODE4)		/* sys_boot0.gpio_2 */
 			OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4)	/* sys_boot1.gpio_3 */
 		>;
 	};
@@ -260,6 +262,11 @@
 #include "twl4030.dtsi"
 #include "twl4030_omap3.dtsi"
 
+&vaux3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+};
+
 &twl {
 	twl_power: power {
 		compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";

arch/arm/boot/dts/r8a7790-lager.dts

@@ -379,7 +379,7 @@
 				port@0 {
 					reg = <0>;
 					adv7511_in: endpoint {
-						remote-endpoint = <&du_out_lvds0>;
+						remote-endpoint = <&lvds0_out>;
 					};
 				};
 
@@ -467,10 +467,8 @@
 	status = "okay";
 
 	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
-		 <&cpg CPG_MOD 726>, <&cpg CPG_MOD 725>,
 		 <&x13_clk>, <&x2_clk>;
-	clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1",
-		      "dclkin.0", "dclkin.1";
+	clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1";
 
 	ports {
 		port@0 {
@@ -478,12 +476,26 @@
 				remote-endpoint = <&adv7123_in>;
 			};
 		};
+	};
+};
+
+&lvds0 {
+	status = "okay";
+
+	ports {
 		port@1 {
 			endpoint {
 				remote-endpoint = <&adv7511_in>;
 			};
 		};
-		port@2 {
+	};
+};
+
+&lvds1 {
+	status = "okay";
+
+	ports {
+		port@1 {
 			lvds_connector: endpoint {
 			};
 		};

arch/arm/boot/dts/r8a7790.dtsi

@@ -1627,18 +1627,13 @@
 
 		du: display@feb00000 {
 			compatible = "renesas,du-r8a7790";
-			reg = <0 0xfeb00000 0 0x70000>,
-			      <0 0xfeb90000 0 0x1c>,
-			      <0 0xfeb94000 0 0x1c>;
-			reg-names = "du", "lvds.0", "lvds.1";
+			reg = <0 0xfeb00000 0 0x70000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>,
-				 <&cpg CPG_MOD 722>, <&cpg CPG_MOD 726>,
-				 <&cpg CPG_MOD 725>;
-			clock-names = "du.0", "du.1", "du.2", "lvds.0",
-				      "lvds.1";
+				 <&cpg CPG_MOD 722>;
+			clock-names = "du.0", "du.1", "du.2";
 			status = "disabled";
 
 			ports {
@@ -1653,11 +1648,65 @@
 				port@1 {
 					reg = <1>;
 					du_out_lvds0: endpoint {
+						remote-endpoint = <&lvds0_in>;
 					};
 				};
 				port@2 {
 					reg = <2>;
 					du_out_lvds1: endpoint {
+						remote-endpoint = <&lvds1_in>;
+					};
+				};
+			};
+		};
+
+		lvds0: lvds@feb90000 {
+			compatible = "renesas,r8a7790-lvds";
+			reg = <0 0xfeb90000 0 0x1c>;
+			clocks = <&cpg CPG_MOD 726>;
+			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+			resets = <&cpg 726>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					lvds0_in: endpoint {
+						remote-endpoint = <&du_out_lvds0>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					lvds0_out: endpoint {
+					};
+				};
+			};
+		};
+
+		lvds1: lvds@feb94000 {
+			compatible = "renesas,r8a7790-lvds";
+			reg = <0 0xfeb94000 0 0x1c>;
+			clocks = <&cpg CPG_MOD 725>;
+			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
+			resets = <&cpg 725>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					lvds1_in: endpoint {
+						remote-endpoint = <&du_out_lvds1>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					lvds1_out: endpoint {
 					};
 				};
 			};

arch/arm/boot/dts/r8a7791-koelsch.dts

@@ -468,10 +468,9 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 726>,
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>,
 		 <&x13_clk>, <&x2_clk>;
-	clock-names = "du.0", "du.1", "lvds.0",
-		      "dclkin.0", "dclkin.1";
+	clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1";
 
 	ports {
 		port@0 {
@@ -479,6 +478,13 @@
 				remote-endpoint = <&adv7511_in>;
 			};
 		};
+	};
+};
+
+&lvds0 {
+	status = "okay";
+
+	ports {
 		port@1 {
 			lvds_connector: endpoint {
 			};

arch/arm/boot/dts/r8a7791-porter.dts

@@ -441,10 +441,9 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 726>,
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>,
 		 <&x3_clk>, <&x16_clk>;
-	clock-names = "du.0", "du.1", "lvds.0",
-		      "dclkin.0", "dclkin.1";
+	clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1";
 
 	ports {
 		port@0 {
@@ -455,6 +454,17 @@
 	};
 };
 
+&lvds0 {
+	status = "okay";
+
+	ports {
+		port@1 {
+			lvds_connector: endpoint {
+			};
+		};
+	};
+};
+
 &rcar_sound {
 	pinctrl-0 = <&ssi_pins &audio_clk_pins>;
 	pinctrl-names = "default";

arch/arm/boot/dts/r8a7791.dtsi

@@ -1633,15 +1633,12 @@
 
 		du: display@feb00000 {
 			compatible = "renesas,du-r8a7791";
-			reg = <0 0xfeb00000 0 0x40000>,
-			      <0 0xfeb90000 0 0x1c>;
-			reg-names = "du", "lvds.0";
+			reg = <0 0xfeb00000 0 0x40000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 724>,
-				 <&cpg CPG_MOD 723>,
-				 <&cpg CPG_MOD 726>;
-			clock-names = "du.0", "du.1", "lvds.0";
+				 <&cpg CPG_MOD 723>;
+			clock-names = "du.0", "du.1";
 			status = "disabled";
 
 			ports {
@@ -1656,6 +1653,33 @@
 				port@1 {
 					reg = <1>;
 					du_out_lvds0: endpoint {
+						remote-endpoint = <&lvds0_in>;
+					};
+				};
+			};
+		};
+
+		lvds0: lvds@feb90000 {
+			compatible = "renesas,r8a7791-lvds";
+			reg = <0 0xfeb90000 0 0x1c>;
+			clocks = <&cpg CPG_MOD 726>;
+			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
+			resets = <&cpg 726>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					lvds0_in: endpoint {
+						remote-endpoint = <&du_out_lvds0>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					lvds0_out: endpoint {
 					};
 				};
 			};

arch/arm/boot/dts/r8a7793-gose.dts

@@ -447,10 +447,9 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 726>,
+	clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>,
 		 <&x13_clk>, <&x2_clk>;
-	clock-names = "du.0", "du.1", "lvds.0",
-		      "dclkin.0", "dclkin.1";
+	clock-names = "du.0", "du.1", "dclkin.0", "dclkin.1";
 
 	ports {
 		port@0 {
@@ -458,6 +457,11 @@
 				remote-endpoint = <&adv7511_in>;
 			};
 		};
+	};
+};
+
+&lvds0 {
+	ports {
 		port@1 {
 			lvds_connector: endpoint {
 			};

arch/arm/boot/dts/r8a7793.dtsi

@@ -1292,15 +1292,12 @@
 
 		du: display@feb00000 {
 			compatible = "renesas,du-r8a7793";
-			reg = <0 0xfeb00000 0 0x40000>,
-			      <0 0xfeb90000 0 0x1c>;
-			reg-names = "du", "lvds.0";
+			reg = <0 0xfeb00000 0 0x40000>;
 			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 724>,
-				 <&cpg CPG_MOD 723>,
-				 <&cpg CPG_MOD 726>;
-			clock-names = "du.0", "du.1", "lvds.0";
+				 <&cpg CPG_MOD 723>;
+			clock-names = "du.0", "du.1";
 			status = "disabled";
 
 			ports {
@@ -1315,6 +1312,34 @@
 				port@1 {
 					reg = <1>;
 					du_out_lvds0: endpoint {
+						remote-endpoint = <&lvds0_in>;
+					};
+				};
+			};
+		};
+
+		lvds0: lvds@feb90000 {
+			compatible = "renesas,r8a7793-lvds";
+			reg = <0 0xfeb90000 0 0x1c>;
+			clocks = <&cpg CPG_MOD 726>;
+			power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
+			resets = <&cpg 726>;
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					lvds0_in: endpoint {
+						remote-endpoint = <&du_out_lvds0>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					lvds0_out: endpoint {
 					};
 				};
 			};

arch/arm/boot/dts/tegra20.dtsi

@@ -741,7 +741,7 @@
 		phy_type = "ulpi";
 		clocks = <&tegra_car TEGRA20_CLK_USB2>,
 			 <&tegra_car TEGRA20_CLK_PLL_U>,
-			 <&tegra_car TEGRA20_CLK_PLL_P_OUT4>;
+			 <&tegra_car TEGRA20_CLK_CDEV2>;
 		clock-names = "reg", "pll_u", "ulpi-link";
 		resets = <&tegra_car 58>, <&tegra_car 22>;
 		reset-names = "usb", "utmi-pads";

arch/arm/include/asm/assembler.h

@@ -536,4 +536,14 @@ THUMB(	orr	\reg , \reg , #PSR_T_BIT	)
 #endif
 	.endm
 
+#ifdef CONFIG_KPROBES
+#define _ASM_NOKPROBE(entry)				\
+	.pushsection "_kprobe_blacklist", "aw" ;	\
+	.balign 4 ;					\
+	.long entry;					\
+	.popsection
+#else
+#define _ASM_NOKPROBE(entry)
+#endif
+
 #endif /* __ASM_ASSEMBLER_H__ */

arch/arm/include/asm/kvm_mmu.h

@@ -309,6 +309,22 @@ static inline unsigned int kvm_get_vmid_bits(void)
 	return 8;
 }
 
+/*
+ * We are not in the kvm->srcu critical section most of the time, so we take
+ * the SRCU read lock here. Since we copy the data from the user page, we
+ * can immediately drop the lock again.
+ */
+static inline int kvm_read_guest_lock(struct kvm *kvm,
+				      gpa_t gpa, void *data, unsigned long len)
+{
+	int srcu_idx = srcu_read_lock(&kvm->srcu);
+	int ret = kvm_read_guest(kvm, gpa, data, len);
+
+	srcu_read_unlock(&kvm->srcu, srcu_idx);
+
+	return ret;
+}
+
 static inline void *kvm_get_hyp_vector(void)
 {
 	return kvm_ksym_ref(__kvm_hyp_vector);

arch/arm/include/uapi/asm/siginfo.h

@@ -1,13 +0,0 @@
-#ifndef __ASM_SIGINFO_H
-#define __ASM_SIGINFO_H
-
-#include <asm-generic/siginfo.h>
-
-/*
- * SIGFPE si_codes
- */
-#ifdef __KERNEL__
-#define FPE_FIXME	0	/* Broken dup of SI_USER */
-#endif /* __KERNEL__ */
-
-#endif

arch/arm/kernel/machine_kexec.c

@@ -83,7 +83,7 @@ void machine_crash_nonpanic_core(void *unused)
 {
 	struct pt_regs regs;
 
-	crash_setup_regs(&regs, NULL);
+	crash_setup_regs(&regs, get_irq_regs());
 	printk(KERN_DEBUG "CPU %u will stop doing anything useful since another CPU has crashed\n",
 	       smp_processor_id());
 	crash_save_cpu(&regs, smp_processor_id());
@@ -95,6 +95,27 @@ void machine_crash_nonpanic_core(void *unused)
 		cpu_relax();
 }
 
+void crash_smp_send_stop(void)
+{
+	static int cpus_stopped;
+	unsigned long msecs;
+
+	if (cpus_stopped)
+		return;
+
+	atomic_set(&waiting_for_crash_ipi, num_online_cpus() - 1);
+	smp_call_function(machine_crash_nonpanic_core, NULL, false);
+	msecs = 1000; /* Wait at most a second for the other cpus to stop */
+	while ((atomic_read(&waiting_for_crash_ipi) > 0) && msecs) {
+		mdelay(1);
+		msecs--;
+	}
+	if (atomic_read(&waiting_for_crash_ipi) > 0)
+		pr_warn("Non-crashing CPUs did not react to IPI\n");
+
+	cpus_stopped = 1;
+}
+
 static void machine_kexec_mask_interrupts(void)
 {
 	unsigned int i;
@@ -120,19 +141,8 @@ static void machine_kexec_mask_interrupts(void)
 
 void machine_crash_shutdown(struct pt_regs *regs)
 {
-	unsigned long msecs;
-
 	local_irq_disable();
-
-	atomic_set(&waiting_for_crash_ipi, num_online_cpus() - 1);
-	smp_call_function(machine_crash_nonpanic_core, NULL, false);
-	msecs = 1000; /* Wait at most a second for the other cpus to stop */
-	while ((atomic_read(&waiting_for_crash_ipi) > 0) && msecs) {
-		mdelay(1);
-		msecs--;
-	}
-	if (atomic_read(&waiting_for_crash_ipi) > 0)
-		pr_warn("Non-crashing CPUs did not react to IPI\n");
+	crash_smp_send_stop();
 
 	crash_save_cpu(regs, smp_processor_id());
 	machine_kexec_mask_interrupts();

arch/arm/kernel/traps.c

@@ -19,6 +19,7 @@
 #include <linux/uaccess.h>
 #include <linux/hardirq.h>
 #include <linux/kdebug.h>
+#include <linux/kprobes.h>
 #include <linux/module.h>
 #include <linux/kexec.h>
 #include <linux/bug.h>
@@ -417,7 +418,8 @@ void unregister_undef_hook(struct undef_hook *hook)
 	raw_spin_unlock_irqrestore(&undef_lock, flags);
 }
 
-static int call_undef_hook(struct pt_regs *regs, unsigned int instr)
+static nokprobe_inline
+int call_undef_hook(struct pt_regs *regs, unsigned int instr)
 {
 	struct undef_hook *hook;
 	unsigned long flags;
@@ -490,6 +492,7 @@ die_sig:
 
 	arm_notify_die("Oops - undefined instruction", regs, &info, 0, 6);
 }
+NOKPROBE_SYMBOL(do_undefinstr)
 
 /*
  * Handle FIQ similarly to NMI on x86 systems.

arch/arm/lib/getuser.S

@@ -38,6 +38,7 @@ ENTRY(__get_user_1)
 	mov	r0, #0
 	ret	lr
 ENDPROC(__get_user_1)
+_ASM_NOKPROBE(__get_user_1)
 
 ENTRY(__get_user_2)
 	check_uaccess r0, 2, r1, r2, __get_user_bad
@@ -58,6 +59,7 @@ rb	.req	r0
 	mov	r0, #0
 	ret	lr
 ENDPROC(__get_user_2)
+_ASM_NOKPROBE(__get_user_2)
 
 ENTRY(__get_user_4)
 	check_uaccess r0, 4, r1, r2, __get_user_bad
@@ -65,6 +67,7 @@ ENTRY(__get_user_4)
 	mov	r0, #0
 	ret	lr
 ENDPROC(__get_user_4)
+_ASM_NOKPROBE(__get_user_4)
 
 ENTRY(__get_user_8)
 	check_uaccess r0, 8, r1, r2, __get_user_bad8
@@ -78,6 +81,7 @@ ENTRY(__get_user_8)
 	mov	r0, #0
 	ret	lr
 ENDPROC(__get_user_8)
+_ASM_NOKPROBE(__get_user_8)
 
 #ifdef __ARMEB__
 ENTRY(__get_user_32t_8)
@@ -91,6 +95,7 @@ ENTRY(__get_user_32t_8)
 	mov	r0, #0
 	ret	lr
 ENDPROC(__get_user_32t_8)
+_ASM_NOKPROBE(__get_user_32t_8)
 
 ENTRY(__get_user_64t_1)
 	check_uaccess r0, 1, r1, r2, __get_user_bad8
@@ -98,6 +103,7 @@ ENTRY(__get_user_64t_1)
 	mov	r0, #0
 	ret	lr
 ENDPROC(__get_user_64t_1)
+_ASM_NOKPROBE(__get_user_64t_1)
 
 ENTRY(__get_user_64t_2)
 	check_uaccess r0, 2, r1, r2, __get_user_bad8
@@ -114,6 +120,7 @@ rb	.req	r0
 	mov	r0, #0
 	ret	lr
 ENDPROC(__get_user_64t_2)
+_ASM_NOKPROBE(__get_user_64t_2)
 
 ENTRY(__get_user_64t_4)
 	check_uaccess r0, 4, r1, r2, __get_user_bad8
@@ -121,6 +128,7 @@ ENTRY(__get_user_64t_4)
 	mov	r0, #0
 	ret	lr
 ENDPROC(__get_user_64t_4)
+_ASM_NOKPROBE(__get_user_64t_4)
 #endif
 
 __get_user_bad8:
@@ -131,6 +139,8 @@ __get_user_bad:
 	ret	lr
 ENDPROC(__get_user_bad)
 ENDPROC(__get_user_bad8)
+_ASM_NOKPROBE(__get_user_bad)
+_ASM_NOKPROBE(__get_user_bad8)
 
 .pushsection __ex_table, "a"
 	.long	1b, __get_user_bad

arch/arm/mach-davinci/board-da830-evm.c

@@ -205,12 +205,17 @@ static const short da830_evm_mmc_sd_pins[] = {
 	-1
 };
 
+#define DA830_MMCSD_WP_PIN		GPIO_TO_PIN(2, 1)
+#define DA830_MMCSD_CD_PIN		GPIO_TO_PIN(2, 2)
+
 static struct gpiod_lookup_table mmc_gpios_table = {
 	.dev_id = "da830-mmc.0",
 	.table = {
 		/* gpio chip 1 contains gpio range 32-63 */
-		GPIO_LOOKUP("davinci_gpio.1", 2, "cd", GPIO_ACTIVE_LOW),
-		GPIO_LOOKUP("davinci_gpio.1", 1, "wp", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.0", DA830_MMCSD_CD_PIN, "cd",
+			    GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.0", DA830_MMCSD_WP_PIN, "wp",
+			    GPIO_ACTIVE_LOW),
 	},
 };
 

arch/arm/mach-davinci/board-da850-evm.c

@@ -763,12 +763,17 @@ static const short da850_evm_mcasp_pins[] __initconst = {
 	-1
 };
 
+#define DA850_MMCSD_CD_PIN		GPIO_TO_PIN(4, 0)
+#define DA850_MMCSD_WP_PIN		GPIO_TO_PIN(4, 1)
+
 static struct gpiod_lookup_table mmc_gpios_table = {
 	.dev_id = "da830-mmc.0",
 	.table = {
 		/* gpio chip 2 contains gpio range 64-95 */
-		GPIO_LOOKUP("davinci_gpio.2", 0, "cd", GPIO_ACTIVE_LOW),
-		GPIO_LOOKUP("davinci_gpio.2", 1, "wp", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.0", DA850_MMCSD_CD_PIN, "cd",
+			    GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.0", DA850_MMCSD_WP_PIN, "wp",
+			    GPIO_ACTIVE_LOW),
 	},
 };
 

arch/arm/mach-davinci/board-dm355-evm.c

@@ -19,6 +19,7 @@
 #include <linux/gpio.h>
 #include <linux/gpio/machine.h>
 #include <linux/clk.h>
+#include <linux/dm9000.h>
 #include <linux/videodev2.h>
 #include <media/i2c/tvp514x.h>
 #include <linux/spi/spi.h>
@@ -109,12 +110,15 @@ static struct platform_device davinci_nand_device = {
 	},
 };
 
+#define DM355_I2C_SDA_PIN	GPIO_TO_PIN(0, 15)
+#define DM355_I2C_SCL_PIN	GPIO_TO_PIN(0, 14)
+
 static struct gpiod_lookup_table i2c_recovery_gpiod_table = {
-	.dev_id = "i2c_davinci",
+	.dev_id = "i2c_davinci.1",
 	.table = {
-		GPIO_LOOKUP("davinci_gpio", 15, "sda",
+		GPIO_LOOKUP("davinci_gpio.0", DM355_I2C_SDA_PIN, "sda",
 			    GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
-		GPIO_LOOKUP("davinci_gpio", 14, "scl",
+		GPIO_LOOKUP("davinci_gpio.0", DM355_I2C_SCL_PIN, "scl",
 			    GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
 	},
 };
@@ -179,11 +183,16 @@ static struct resource dm355evm_dm9000_rsrc[] = {
 	},
 };
 
+static struct dm9000_plat_data dm335evm_dm9000_platdata;
+
 static struct platform_device dm355evm_dm9000 = {
 	.name		= "dm9000",
 	.id		= -1,
 	.resource	= dm355evm_dm9000_rsrc,
 	.num_resources	= ARRAY_SIZE(dm355evm_dm9000_rsrc),
+	.dev		= {
+		.platform_data = &dm335evm_dm9000_platdata,
+	},
 };
 
 static struct tvp514x_platform_data tvp5146_pdata = {

arch/arm/mach-davinci/board-dm644x-evm.c

@@ -17,6 +17,7 @@
 #include <linux/i2c.h>
 #include <linux/platform_data/pcf857x.h>
 #include <linux/platform_data/at24.h>
+#include <linux/platform_data/gpio-davinci.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/rawnand.h>
 #include <linux/mtd/partitions.h>
@@ -596,12 +597,15 @@ static struct i2c_board_info __initdata i2c_info[] =  {
 	},
 };
 
+#define DM644X_I2C_SDA_PIN	GPIO_TO_PIN(2, 12)
+#define DM644X_I2C_SCL_PIN	GPIO_TO_PIN(2, 11)
+
 static struct gpiod_lookup_table i2c_recovery_gpiod_table = {
-	.dev_id = "i2c_davinci",
+	.dev_id = "i2c_davinci.1",
 	.table = {
-		GPIO_LOOKUP("davinci_gpio", 44, "sda",
+		GPIO_LOOKUP("davinci_gpio.0", DM644X_I2C_SDA_PIN, "sda",
 			    GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
-		GPIO_LOOKUP("davinci_gpio", 43, "scl",
+		GPIO_LOOKUP("davinci_gpio.0", DM644X_I2C_SCL_PIN, "scl",
 			    GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
 	},
 };

arch/arm/mach-davinci/board-dm646x-evm.c

@@ -532,11 +532,12 @@ static struct vpif_display_config dm646x_vpif_display_config = {
 	.set_clock	= set_vpif_clock,
 	.subdevinfo	= dm646x_vpif_subdev,
 	.subdev_count	= ARRAY_SIZE(dm646x_vpif_subdev),
+	.i2c_adapter_id = 1,
 	.chan_config[0] = {
 		.outputs = dm6467_ch0_outputs,
 		.output_count = ARRAY_SIZE(dm6467_ch0_outputs),
 	},
-	.card_name	= "DM646x EVM",
+	.card_name	= "DM646x EVM Video Display",
 };
 
 /**
@@ -674,6 +675,7 @@ static struct vpif_capture_config dm646x_vpif_capture_cfg = {
 	.setup_input_channel_mode = setup_vpif_input_channel_mode,
 	.subdev_info = vpif_capture_sdev_info,
 	.subdev_count = ARRAY_SIZE(vpif_capture_sdev_info),
+	.i2c_adapter_id = 1,
 	.chan_config[0] = {
 		.inputs = dm6467_ch0_inputs,
 		.input_count = ARRAY_SIZE(dm6467_ch0_inputs),
@@ -694,6 +696,7 @@ static struct vpif_capture_config dm646x_vpif_capture_cfg = {
 			.fid_pol = 0,
 		},
 	},
+	.card_name = "DM646x EVM Video Capture",
 };
 
 static void __init evm_init_video(void)

arch/arm/mach-davinci/board-omapl138-hawk.c

@@ -123,12 +123,16 @@ static const short hawk_mmcsd0_pins[] = {
 	-1
 };
 
+#define DA850_HAWK_MMCSD_CD_PIN		GPIO_TO_PIN(3, 12)
+#define DA850_HAWK_MMCSD_WP_PIN		GPIO_TO_PIN(3, 13)
+
 static struct gpiod_lookup_table mmc_gpios_table = {
 	.dev_id = "da830-mmc.0",
 	.table = {
-		/* CD: gpio3_12: gpio60: chip 1 contains gpio range 32-63*/
-		GPIO_LOOKUP("davinci_gpio.0", 28, "cd", GPIO_ACTIVE_LOW),
-		GPIO_LOOKUP("davinci_gpio.0", 29, "wp", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.0", DA850_HAWK_MMCSD_CD_PIN, "cd",
+			    GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("davinci_gpio.0", DA850_HAWK_MMCSD_WP_PIN, "wp",
+			    GPIO_ACTIVE_LOW),
 	},
 };
 

arch/arm/mach-davinci/dm646x.c

@@ -488,7 +488,8 @@ static u8 dm646x_default_priorities[DAVINCI_N_AINTC_IRQ] = {
 	[IRQ_DM646X_MCASP0TXINT]        = 7,
 	[IRQ_DM646X_MCASP0RXINT]        = 7,
 	[IRQ_DM646X_RESERVED_3]         = 7,
-	[IRQ_DM646X_MCASP1TXINT]        = 7,    /* clockevent */
+	[IRQ_DM646X_MCASP1TXINT]        = 7,
+	[IRQ_TINT0_TINT12]              = 7,    /* clockevent */
 	[IRQ_TINT0_TINT34]              = 7,    /* clocksource */
 	[IRQ_TINT1_TINT12]              = 7,    /* DSP timer */
 	[IRQ_TINT1_TINT34]              = 7,    /* system tick */

arch/arm/mach-keystone/pm_domain.c

@@ -29,6 +29,7 @@ static struct dev_pm_domain keystone_pm_domain = {
 
 static struct pm_clk_notifier_block platform_domain_notifier = {
 	.pm_domain = &keystone_pm_domain,
+	.con_ids = { NULL },
 };
 
 static const struct of_device_id of_keystone_table[] = {

arch/arm/mach-omap1/ams-delta-fiq.c

@@ -58,22 +58,24 @@ static irqreturn_t deferred_fiq(int irq, void *dev_id)
 		irq_num = gpio_to_irq(gpio);
 		fiq_count = fiq_buffer[FIQ_CNT_INT_00 + gpio];
 
-		while (irq_counter[gpio] < fiq_count) {
-			if (gpio != AMS_DELTA_GPIO_PIN_KEYBRD_CLK) {
-				struct irq_data *d = irq_get_irq_data(irq_num);
-
-				/*
-				 * It looks like handle_edge_irq() that
-				 * OMAP GPIO edge interrupts default to,
-				 * expects interrupt already unmasked.
-				 */
-				if (irq_chip && irq_chip->irq_unmask)
+		if (irq_counter[gpio] < fiq_count &&
+				gpio != AMS_DELTA_GPIO_PIN_KEYBRD_CLK) {
+			struct irq_data *d = irq_get_irq_data(irq_num);
+
+			/*
+			 * handle_simple_irq() that OMAP GPIO edge
+			 * interrupts default to since commit 80ac93c27441
+			 * requires interrupt already acked and unmasked.
+			 */
+			if (irq_chip) {
+				if (irq_chip->irq_ack)
+					irq_chip->irq_ack(d);
+				if (irq_chip->irq_unmask)
 					irq_chip->irq_unmask(d);
 			}
-			generic_handle_irq(irq_num);
-
-			irq_counter[gpio]++;
 		}
+		for (; irq_counter[gpio] < fiq_count; irq_counter[gpio]++)
+			generic_handle_irq(irq_num);
 	}
 	return IRQ_HANDLED;
 }

arch/arm/mach-omap2/powerdomain.c

@@ -188,7 +188,7 @@ static int _pwrdm_state_switch(struct powerdomain *pwrdm, int flag)
 				       ((prev & OMAP_POWERSTATE_MASK) << 0));
 			trace_power_domain_target_rcuidle(pwrdm->name,
 							  trace_state,
-							  smp_processor_id());
+							  raw_smp_processor_id());
 		}
 		break;
 	default:
@@ -518,7 +518,7 @@ int pwrdm_set_next_pwrst(struct powerdomain *pwrdm, u8 pwrst)
 	if (arch_pwrdm && arch_pwrdm->pwrdm_set_next_pwrst) {
 		/* Trace the pwrdm desired target state */
 		trace_power_domain_target_rcuidle(pwrdm->name, pwrst,
-						  smp_processor_id());
+						  raw_smp_processor_id());
 		/* Program the pwrdm desired target state */
 		ret = arch_pwrdm->pwrdm_set_next_pwrst(pwrdm, pwrst);
 	}

arch/arm/probes/kprobes/opt-arm.c

@@ -165,13 +165,14 @@ optimized_callback(struct optimized_kprobe *op, struct pt_regs *regs)
 {
 	unsigned long flags;
 	struct kprobe *p = &op->kp;
-	struct kprobe_ctlblk *kcb = get_kprobe_ctlblk();
+	struct kprobe_ctlblk *kcb;
 
 	/* Save skipped registers */
 	regs->ARM_pc = (unsigned long)op->kp.addr;
 	regs->ARM_ORIG_r0 = ~0UL;
 
 	local_irq_save(flags);
+	kcb = get_kprobe_ctlblk();
 
 	if (kprobe_running()) {
 		kprobes_inc_nmissed_count(&op->kp);
@@ -191,6 +192,7 @@ optimized_callback(struct optimized_kprobe *op, struct pt_regs *regs)
 
 	local_irq_restore(flags);
 }
+NOKPROBE_SYMBOL(optimized_callback)
 
 int arch_prepare_optimized_kprobe(struct optimized_kprobe *op, struct kprobe *orig)
 {

arch/arm/vfp/vfpmodule.c

@@ -257,7 +257,7 @@ static void vfp_raise_exceptions(u32 exceptions, u32 inst, u32 fpscr, struct pt_
 
 	if (exceptions == VFP_EXCEPTION_ERROR) {
 		vfp_panic("unhandled bounce", inst);
-		vfp_raise_sigfpe(FPE_FIXME, regs);
+		vfp_raise_sigfpe(FPE_FLTINV, regs);
 		return;
 	}
 

arch/arm64/boot/dts/exynos/exynos5433.dtsi

@@ -1317,7 +1317,7 @@
 			reg = <0x14d60000 0x100>;
 			dmas = <&pdma0 31 &pdma0 30>;
 			dma-names = "tx", "rx";
-			interrupts = <GIC_SPI 435 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 435 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cmu_peric CLK_PCLK_I2S1>,
 				 <&cmu_peric CLK_PCLK_I2S1>,
 				 <&cmu_peric CLK_SCLK_I2S1>;

arch/arm64/boot/dts/marvell/armada-cp110.dtsi

@@ -38,9 +38,10 @@
 			compatible = "marvell,armada-7k-pp22";
 			reg = <0x0 0x100000>, <0x129000 0xb000>;
 			clocks = <&CP110_LABEL(clk) 1 3>, <&CP110_LABEL(clk) 1 9>,
-				 <&CP110_LABEL(clk) 1 5>, <&CP110_LABEL(clk) 1 18>;
+				 <&CP110_LABEL(clk) 1 5>, <&CP110_LABEL(clk) 1 6>,
+				 <&CP110_LABEL(clk) 1 18>;
 			clock-names = "pp_clk", "gop_clk",
-				      "mg_clk", "axi_clk";
+				      "mg_clk", "mg_core_clk", "axi_clk";
 			marvell,system-controller = <&CP110_LABEL(syscon0)>;
 			status = "disabled";
 			dma-coherent;
@@ -141,6 +142,8 @@
 			#size-cells = <0>;
 			compatible = "marvell,xmdio";
 			reg = <0x12a600 0x10>;
+			clocks = <&CP110_LABEL(clk) 1 5>,
+				 <&CP110_LABEL(clk) 1 6>, <&CP110_LABEL(clk) 1 18>;
 			status = "disabled";
 		};
 

arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi

@@ -46,7 +46,7 @@
 				compatible = "ethernet-phy-ieee802.3-c22";
 				reg = <0x0>;
 				interrupt-parent = <&gpio>;
-				interrupts = <TEGRA_MAIN_GPIO(M, 5) IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <TEGRA_MAIN_GPIO(M, 5) IRQ_TYPE_LEVEL_LOW>;
 			};
 		};
 	};

arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi

@@ -414,7 +414,7 @@
 			mmc-ddr-1_8v;
 			mmc-hs200-1_8v;
 			mmc-pwrseq = <&emmc_pwrseq>;
-			cdns,phy-input-delay-legacy = <4>;
+			cdns,phy-input-delay-legacy = <9>;
 			cdns,phy-input-delay-mmc-highspeed = <2>;
 			cdns,phy-input-delay-mmc-ddr = <3>;
 			cdns,phy-dll-delay-sdclk = <21>;

arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts

@@ -67,3 +67,11 @@
 		reg = <0>;
 	};
 };
+
+&pinctrl_ether_rgmii {
+	tx {
+		pins = "RGMII_TXCLK", "RGMII_TXD0", "RGMII_TXD1",
+		       "RGMII_TXD2", "RGMII_TXD3", "RGMII_TXCTL";
+		drive-strength = <9>;
+	};
+};

arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi

@@ -519,7 +519,7 @@
 			mmc-ddr-1_8v;
 			mmc-hs200-1_8v;
 			mmc-pwrseq = <&emmc_pwrseq>;
-			cdns,phy-input-delay-legacy = <4>;
+			cdns,phy-input-delay-legacy = <9>;
 			cdns,phy-input-delay-mmc-highspeed = <2>;
 			cdns,phy-input-delay-mmc-ddr = <3>;
 			cdns,phy-dll-delay-sdclk = <21>;

arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi

@@ -334,7 +334,7 @@
 			mmc-ddr-1_8v;
 			mmc-hs200-1_8v;
 			mmc-pwrseq = <&emmc_pwrseq>;
-			cdns,phy-input-delay-legacy = <4>;
+			cdns,phy-input-delay-legacy = <9>;
 			cdns,phy-input-delay-mmc-highspeed = <2>;
 			cdns,phy-input-delay-mmc-ddr = <3>;
 			cdns,phy-dll-delay-sdclk = <21>;

arch/arm64/include/asm/cputype.h

@@ -75,6 +75,7 @@
 #define ARM_CPU_IMP_CAVIUM		0x43
 #define ARM_CPU_IMP_BRCM		0x42
 #define ARM_CPU_IMP_QCOM		0x51
+#define ARM_CPU_IMP_NVIDIA		0x4E
 
 #define ARM_CPU_PART_AEM_V8		0xD0F
 #define ARM_CPU_PART_FOUNDATION		0xD00
@@ -99,6 +100,9 @@
 #define QCOM_CPU_PART_FALKOR		0xC00
 #define QCOM_CPU_PART_KRYO		0x200
 
+#define NVIDIA_CPU_PART_DENVER		0x003
+#define NVIDIA_CPU_PART_CARMEL		0x004
+
 #define MIDR_CORTEX_A53 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A53)
 #define MIDR_CORTEX_A57 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A57)
 #define MIDR_CORTEX_A72 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A72)
@@ -114,6 +118,8 @@
 #define MIDR_QCOM_FALKOR_V1 MIDR_CPU_MODEL(ARM_CPU_IMP_QCOM, QCOM_CPU_PART_FALKOR_V1)
 #define MIDR_QCOM_FALKOR MIDR_CPU_MODEL(ARM_CPU_IMP_QCOM, QCOM_CPU_PART_FALKOR)
 #define MIDR_QCOM_KRYO MIDR_CPU_MODEL(ARM_CPU_IMP_QCOM, QCOM_CPU_PART_KRYO)
+#define MIDR_NVIDIA_DENVER MIDR_CPU_MODEL(ARM_CPU_IMP_NVIDIA, NVIDIA_CPU_PART_DENVER)
+#define MIDR_NVIDIA_CARMEL MIDR_CPU_MODEL(ARM_CPU_IMP_NVIDIA, NVIDIA_CPU_PART_CARMEL)
 
 #ifndef __ASSEMBLY__
 

arch/arm64/include/asm/kvm_mmu.h

@@ -360,6 +360,22 @@ static inline unsigned int kvm_get_vmid_bits(void)
 	return (cpuid_feature_extract_unsigned_field(reg, ID_AA64MMFR1_VMIDBITS_SHIFT) == 2) ? 16 : 8;
 }
 
+/*
+ * We are not in the kvm->srcu critical section most of the time, so we take
+ * the SRCU read lock here. Since we copy the data from the user page, we
+ * can immediately drop the lock again.
+ */
+static inline int kvm_read_guest_lock(struct kvm *kvm,
+				      gpa_t gpa, void *data, unsigned long len)
+{
+	int srcu_idx = srcu_read_lock(&kvm->srcu);
+	int ret = kvm_read_guest(kvm, gpa, data, len);
+
+	srcu_read_unlock(&kvm->srcu, srcu_idx);
+
+	return ret;
+}
+
 #ifdef CONFIG_KVM_INDIRECT_VECTORS
 /*
  * EL2 vectors can be mapped and rerouted in a number of ways,

arch/arm64/kernel/cpu_errata.c

@@ -316,6 +316,7 @@ static const struct midr_range arm64_bp_harden_smccc_cpus[] = {
 	MIDR_ALL_VERSIONS(MIDR_CAVIUM_THUNDERX2),
 	MIDR_ALL_VERSIONS(MIDR_QCOM_FALKOR_V1),
 	MIDR_ALL_VERSIONS(MIDR_QCOM_FALKOR),
+	MIDR_ALL_VERSIONS(MIDR_NVIDIA_DENVER),
 	{},
 };
 

arch/arm64/mm/init.c

@@ -646,8 +646,10 @@ static int keep_initrd __initdata;
 
 void __init free_initrd_mem(unsigned long start, unsigned long end)
 {
-	if (!keep_initrd)
+	if (!keep_initrd) {
 		free_reserved_area((void *)start, (void *)end, 0, "initrd");
+		memblock_free(__virt_to_phys(start), end - start);
+	}
 }
 
 static int __init keepinitrd_setup(char *__unused)

arch/parisc/kernel/drivers.c

@@ -268,7 +268,7 @@ static struct parisc_device *find_device_by_addr(unsigned long hpa)
  * Walks up the device tree looking for a device of the specified type.
  * If it finds it, it returns it.  If not, it returns NULL.
  */
-const struct parisc_device * __init
+const struct parisc_device *
 find_pa_parent_type(const struct parisc_device *padev, int type)
 {
 	const struct device *dev = &padev->dev;

arch/parisc/kernel/smp.c

@@ -423,8 +423,7 @@ int __cpu_up(unsigned int cpu, struct task_struct *tidle)
 }
 
 #ifdef CONFIG_PROC_FS
-int __init
-setup_profiling_timer(unsigned int multiplier)
+int setup_profiling_timer(unsigned int multiplier)
 {
 	return -EINVAL;
 }

arch/powerpc/include/asm/ftrace.h

@@ -69,17 +69,30 @@ struct dyn_arch_ftrace {
 #endif
 
 #if defined(CONFIG_FTRACE_SYSCALLS) && !defined(__ASSEMBLY__)
-#ifdef PPC64_ELF_ABI_v1
+/*
+ * Some syscall entry functions on powerpc start with "ppc_" (fork and clone,
+ * for instance) or ppc32_/ppc64_. We should also match the sys_ variant with
+ * those.
+ */
 #define ARCH_HAS_SYSCALL_MATCH_SYM_NAME
+#ifdef PPC64_ELF_ABI_v1
+static inline bool arch_syscall_match_sym_name(const char *sym, const char *name)
+{
+	/* We need to skip past the initial dot, and the __se_sys alias */
+	return !strcmp(sym + 1, name) ||
+		(!strncmp(sym, ".__se_sys", 9) && !strcmp(sym + 6, name)) ||
+		(!strncmp(sym, ".ppc_", 5) && !strcmp(sym + 5, name + 4)) ||
+		(!strncmp(sym, ".ppc32_", 7) && !strcmp(sym + 7, name + 4)) ||
+		(!strncmp(sym, ".ppc64_", 7) && !strcmp(sym + 7, name + 4));
+}
+#else
 static inline bool arch_syscall_match_sym_name(const char *sym, const char *name)
 {
-	/*
-	 * Compare the symbol name with the system call name. Skip the .sys or .SyS
-	 * prefix from the symbol name and the sys prefix from the system call name and
-	 * just match the rest. This is only needed on ppc64 since symbol names on
-	 * 32bit do not start with a period so the generic function will work.
-	 */
-	return !strcmp(sym + 4, name + 3);
+	return !strcmp(sym, name) ||
+		(!strncmp(sym, "__se_sys", 8) && !strcmp(sym + 5, name)) ||
+		(!strncmp(sym, "ppc_", 4) && !strcmp(sym + 4, name + 4)) ||
+		(!strncmp(sym, "ppc32_", 6) && !strcmp(sym + 6, name + 4)) ||
+		(!strncmp(sym, "ppc64_", 6) && !strcmp(sym + 6, name + 4));
 }
 #endif
 #endif /* CONFIG_FTRACE_SYSCALLS && !__ASSEMBLY__ */

arch/powerpc/include/asm/paca.h

@@ -165,7 +165,6 @@ struct paca_struct {
 	u64 saved_msr;			/* MSR saved here by enter_rtas */
 	u16 trap_save;			/* Used when bad stack is encountered */
 	u8 irq_soft_mask;		/* mask for irq soft masking */
-	u8 soft_enabled;		/* irq soft-enable flag */
 	u8 irq_happened;		/* irq happened while soft-disabled */
 	u8 io_sync;			/* writel() needs spin_unlock sync */
 	u8 irq_work_pending;		/* IRQ_WORK interrupt while soft-disable */

arch/powerpc/include/asm/topology.h

@@ -91,6 +91,7 @@ extern int start_topology_update(void);
 extern int stop_topology_update(void);
 extern int prrn_is_enabled(void);
 extern int find_and_online_cpu_nid(int cpu);
+extern int timed_topology_update(int nsecs);
 #else
 static inline int start_topology_update(void)
 {
@@ -108,16 +109,12 @@ static inline int find_and_online_cpu_nid(int cpu)
 {
 	return 0;
 }
+static inline int timed_topology_update(int nsecs)
+{
+	return 0;
+}
 #endif /* CONFIG_NUMA && CONFIG_PPC_SPLPAR */
 
-#if defined(CONFIG_HOTPLUG_CPU) || defined(CONFIG_NEED_MULTIPLE_NODES)
-#if defined(CONFIG_PPC_SPLPAR)
-extern int timed_topology_update(int nsecs);
-#else
-#define	timed_topology_update(nsecs)
-#endif /* CONFIG_PPC_SPLPAR */
-#endif /* CONFIG_HOTPLUG_CPU || CONFIG_NEED_MULTIPLE_NODES */
-
 #include <asm-generic/topology.h>
 
 #ifdef CONFIG_SMP

arch/powerpc/platforms/powernv/opal-nvram.c

@@ -44,6 +44,10 @@ static ssize_t opal_nvram_read(char *buf, size_t count, loff_t *index)
 	return count;
 }
 
+/*
+ * This can be called in the panic path with interrupts off, so use
+ * mdelay in that case.
+ */
 static ssize_t opal_nvram_write(char *buf, size_t count, loff_t *index)
 {
 	s64 rc = OPAL_BUSY;
@@ -58,10 +62,16 @@ static ssize_t opal_nvram_write(char *buf, size_t count, loff_t *index)
 	while (rc == OPAL_BUSY || rc == OPAL_BUSY_EVENT) {
 		rc = opal_write_nvram(__pa(buf), count, off);
 		if (rc == OPAL_BUSY_EVENT) {
-			msleep(OPAL_BUSY_DELAY_MS);
+			if (in_interrupt() || irqs_disabled())
+				mdelay(OPAL_BUSY_DELAY_MS);
+			else
+				msleep(OPAL_BUSY_DELAY_MS);
 			opal_poll_events(NULL);
 		} else if (rc == OPAL_BUSY) {
-			msleep(OPAL_BUSY_DELAY_MS);
+			if (in_interrupt() || irqs_disabled())
+				mdelay(OPAL_BUSY_DELAY_MS);
+			else
+				msleep(OPAL_BUSY_DELAY_MS);
 		}
 	}
 

arch/s390/configs/debug_defconfig

@@ -261,9 +261,9 @@ CONFIG_IP_VS_NQ=m
 CONFIG_IP_VS_FTP=m
 CONFIG_IP_VS_PE_SIP=m
 CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_NF_TABLES_IPV4=m
+CONFIG_NF_TABLES_IPV4=y
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
-CONFIG_NF_TABLES_ARP=m
+CONFIG_NF_TABLES_ARP=y
 CONFIG_NFT_CHAIN_NAT_IPV4=m
 CONFIG_IP_NF_IPTABLES=m
 CONFIG_IP_NF_MATCH_AH=m
@@ -284,7 +284,7 @@ CONFIG_IP_NF_ARPTABLES=m
 CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
 CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_NF_TABLES_IPV6=m
+CONFIG_NF_TABLES_IPV6=y
 CONFIG_NFT_CHAIN_ROUTE_IPV6=m
 CONFIG_NFT_CHAIN_NAT_IPV6=m
 CONFIG_IP6_NF_IPTABLES=m
@@ -305,7 +305,7 @@ CONFIG_IP6_NF_RAW=m
 CONFIG_IP6_NF_SECURITY=m
 CONFIG_IP6_NF_NAT=m
 CONFIG_IP6_NF_TARGET_MASQUERADE=m
-CONFIG_NF_TABLES_BRIDGE=m
+CONFIG_NF_TABLES_BRIDGE=y
 CONFIG_RDS=m
 CONFIG_RDS_RDMA=m
 CONFIG_RDS_TCP=m
@@ -604,7 +604,6 @@ CONFIG_DETECT_HUNG_TASK=y
 CONFIG_WQ_WATCHDOG=y
 CONFIG_PANIC_ON_OOPS=y
 CONFIG_DEBUG_TIMEKEEPING=y
-CONFIG_DEBUG_WW_MUTEX_SLOWPATH=y
 CONFIG_PROVE_LOCKING=y
 CONFIG_LOCK_STAT=y
 CONFIG_DEBUG_LOCKDEP=y

arch/s390/configs/performance_defconfig

@@ -259,9 +259,9 @@ CONFIG_IP_VS_NQ=m
 CONFIG_IP_VS_FTP=m
 CONFIG_IP_VS_PE_SIP=m
 CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_NF_TABLES_IPV4=m
+CONFIG_NF_TABLES_IPV4=y
 CONFIG_NFT_CHAIN_ROUTE_IPV4=m
-CONFIG_NF_TABLES_ARP=m
+CONFIG_NF_TABLES_ARP=y
 CONFIG_NFT_CHAIN_NAT_IPV4=m
 CONFIG_IP_NF_IPTABLES=m
 CONFIG_IP_NF_MATCH_AH=m
@@ -282,7 +282,7 @@ CONFIG_IP_NF_ARPTABLES=m
 CONFIG_IP_NF_ARPFILTER=m
 CONFIG_IP_NF_ARP_MANGLE=m
 CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_NF_TABLES_IPV6=m
+CONFIG_NF_TABLES_IPV6=y
 CONFIG_NFT_CHAIN_ROUTE_IPV6=m
 CONFIG_NFT_CHAIN_NAT_IPV6=m
 CONFIG_IP6_NF_IPTABLES=m
@@ -303,7 +303,7 @@ CONFIG_IP6_NF_RAW=m
 CONFIG_IP6_NF_SECURITY=m
 CONFIG_IP6_NF_NAT=m
 CONFIG_IP6_NF_TARGET_MASQUERADE=m
-CONFIG_NF_TABLES_BRIDGE=m
+CONFIG_NF_TABLES_BRIDGE=y
 CONFIG_RDS=m
 CONFIG_RDS_RDMA=m
 CONFIG_RDS_TCP=m

arch/s390/crypto/crc32be-vx.S

@@ -13,6 +13,7 @@
  */
 
 #include <linux/linkage.h>
+#include <asm/nospec-insn.h>
 #include <asm/vx-insn.h>
 
 /* Vector register range containing CRC-32 constants */
@@ -67,6 +68,8 @@
 
 .previous
 
+	GEN_BR_THUNK %r14
+
 .text
 /*
  * The CRC-32 function(s) use these calling conventions:
@@ -203,6 +206,6 @@ ENTRY(crc32_be_vgfm_16)
 
 .Ldone:
 	VLGVF	%r2,%v2,3
-	br	%r14
+	BR_EX	%r14
 
 .previous

arch/s390/crypto/crc32le-vx.S

@@ -14,6 +14,7 @@
  */
 
 #include <linux/linkage.h>
+#include <asm/nospec-insn.h>
 #include <asm/vx-insn.h>
 
 /* Vector register range containing CRC-32 constants */
@@ -76,6 +77,7 @@
 
 .previous
 
+	GEN_BR_THUNK %r14
 
 .text
 
@@ -264,6 +266,6 @@ crc32_le_vgfm_generic:
 
 .Ldone:
 	VLGVF	%r2,%v2,2
-	br	%r14
+	BR_EX	%r14
 
 .previous

arch/s390/include/asm/nospec-insn.h

@@ -0,0 +1,196 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _ASM_S390_NOSPEC_ASM_H
+#define _ASM_S390_NOSPEC_ASM_H
+
+#include <asm/alternative-asm.h>
+#include <asm/asm-offsets.h>
+#include <asm/dwarf.h>
+
+#ifdef __ASSEMBLY__
+
+#ifdef CONFIG_EXPOLINE
+
+_LC_BR_R1 = __LC_BR_R1
+
+/*
+ * The expoline macros are used to create thunks in the same format
+ * as gcc generates them. The 'comdat' section flag makes sure that
+ * the various thunks are merged into a single copy.
+ */
+	.macro __THUNK_PROLOG_NAME name
+	.pushsection .text.\name,"axG",@progbits,\name,comdat
+	.globl \name
+	.hidden \name
+	.type \name,@function
+\name:
+	CFI_STARTPROC
+	.endm
+
+	.macro __THUNK_EPILOG
+	CFI_ENDPROC
+	.popsection
+	.endm
+
+	.macro __THUNK_PROLOG_BR r1,r2
+	__THUNK_PROLOG_NAME __s390x_indirect_jump_r\r2\()use_r\r1
+	.endm
+
+	.macro __THUNK_PROLOG_BC d0,r1,r2
+	__THUNK_PROLOG_NAME __s390x_indirect_branch_\d0\()_\r2\()use_\r1
+	.endm
+
+	.macro __THUNK_BR r1,r2
+	jg	__s390x_indirect_jump_r\r2\()use_r\r1
+	.endm
+
+	.macro __THUNK_BC d0,r1,r2
+	jg	__s390x_indirect_branch_\d0\()_\r2\()use_\r1
+	.endm
+
+	.macro __THUNK_BRASL r1,r2,r3
+	brasl	\r1,__s390x_indirect_jump_r\r3\()use_r\r2
+	.endm
+
+	.macro	__DECODE_RR expand,reg,ruse
+	.set __decode_fail,1
+	.irp r1,0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
+	.ifc \reg,%r\r1
+	.irp r2,0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
+	.ifc \ruse,%r\r2
+	\expand \r1,\r2
+	.set __decode_fail,0
+	.endif
+	.endr
+	.endif
+	.endr
+	.if __decode_fail == 1
+	.error "__DECODE_RR failed"
+	.endif
+	.endm
+
+	.macro	__DECODE_RRR expand,rsave,rtarget,ruse
+	.set __decode_fail,1
+	.irp r1,0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
+	.ifc \rsave,%r\r1
+	.irp r2,0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
+	.ifc \rtarget,%r\r2
+	.irp r3,0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
+	.ifc \ruse,%r\r3
+	\expand \r1,\r2,\r3
+	.set __decode_fail,0
+	.endif
+	.endr
+	.endif
+	.endr
+	.endif
+	.endr
+	.if __decode_fail == 1
+	.error "__DECODE_RRR failed"
+	.endif
+	.endm
+
+	.macro	__DECODE_DRR expand,disp,reg,ruse
+	.set __decode_fail,1
+	.irp r1,0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
+	.ifc \reg,%r\r1
+	.irp r2,0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
+	.ifc \ruse,%r\r2
+	\expand \disp,\r1,\r2
+	.set __decode_fail,0
+	.endif
+	.endr
+	.endif
+	.endr
+	.if __decode_fail == 1
+	.error "__DECODE_DRR failed"
+	.endif
+	.endm
+
+	.macro __THUNK_EX_BR reg,ruse
+	# Be very careful when adding instructions to this macro!
+	# The ALTERNATIVE replacement code has a .+10 which targets
+	# the "br \reg" after the code has been patched.
+#ifdef CONFIG_HAVE_MARCH_Z10_FEATURES
+	exrl	0,555f
+	j	.
+#else
+	.ifc \reg,%r1
+	ALTERNATIVE "ex %r0,_LC_BR_R1", ".insn ril,0xc60000000000,0,.+10", 35
+	j	.
+	.else
+	larl	\ruse,555f
+	ex	0,0(\ruse)
+	j	.
+	.endif
+#endif
+555:	br	\reg
+	.endm
+
+	.macro __THUNK_EX_BC disp,reg,ruse
+#ifdef CONFIG_HAVE_MARCH_Z10_FEATURES
+	exrl	0,556f
+	j	.
+#else
+	larl	\ruse,556f
+	ex	0,0(\ruse)
+	j	.
+#endif
+556:	b	\disp(\reg)
+	.endm
+
+	.macro GEN_BR_THUNK reg,ruse=%r1
+	__DECODE_RR __THUNK_PROLOG_BR,\reg,\ruse
+	__THUNK_EX_BR \reg,\ruse
+	__THUNK_EPILOG
+	.endm
+
+	.macro GEN_B_THUNK disp,reg,ruse=%r1
+	__DECODE_DRR __THUNK_PROLOG_BC,\disp,\reg,\ruse
+	__THUNK_EX_BC \disp,\reg,\ruse
+	__THUNK_EPILOG
+	.endm
+
+	.macro BR_EX reg,ruse=%r1
+557:	__DECODE_RR __THUNK_BR,\reg,\ruse
+	.pushsection .s390_indirect_branches,"a",@progbits
+	.long	557b-.
+	.popsection
+	.endm
+
+	 .macro B_EX disp,reg,ruse=%r1
+558:	__DECODE_DRR __THUNK_BC,\disp,\reg,\ruse
+	.pushsection .s390_indirect_branches,"a",@progbits
+	.long	558b-.
+	.popsection
+	.endm
+
+	.macro BASR_EX rsave,rtarget,ruse=%r1
+559:	__DECODE_RRR __THUNK_BRASL,\rsave,\rtarget,\ruse
+	.pushsection .s390_indirect_branches,"a",@progbits
+	.long	559b-.
+	.popsection
+	.endm
+
+#else
+	.macro GEN_BR_THUNK reg,ruse=%r1
+	.endm
+
+	.macro GEN_B_THUNK disp,reg,ruse=%r1
+	.endm
+
+	 .macro BR_EX reg,ruse=%r1
+	br	\reg
+	.endm
+
+	 .macro B_EX disp,reg,ruse=%r1
+	b	\disp(\reg)
+	.endm
+
+	.macro BASR_EX rsave,rtarget,ruse=%r1
+	basr	\rsave,\rtarget
+	.endm
+#endif
+
+#endif /* __ASSEMBLY__ */
+
+#endif /* _ASM_S390_NOSPEC_ASM_H */

arch/s390/include/asm/purgatory.h

@@ -13,5 +13,11 @@
 
 int verify_sha256_digest(void);
 
+extern u64 kernel_entry;
+extern u64 kernel_type;
+
+extern u64 crash_start;
+extern u64 crash_size;
+
 #endif	/* __ASSEMBLY__ */
 #endif /* _S390_PURGATORY_H_ */

arch/s390/kernel/Makefile

@@ -65,6 +65,7 @@ obj-y	+= nospec-branch.o
 
 extra-y				+= head.o head64.o vmlinux.lds
 
+obj-$(CONFIG_SYSFS)		+= nospec-sysfs.o
 CFLAGS_REMOVE_nospec-branch.o	+= $(CC_FLAGS_EXPOLINE)
 
 obj-$(CONFIG_MODULES)		+= module.o

arch/s390/kernel/asm-offsets.c

@@ -181,6 +181,7 @@ int main(void)
 	OFFSET(__LC_MACHINE_FLAGS, lowcore, machine_flags);
 	OFFSET(__LC_PREEMPT_COUNT, lowcore, preempt_count);
 	OFFSET(__LC_GMAP, lowcore, gmap);
+	OFFSET(__LC_BR_R1, lowcore, br_r1_trampoline);
 	/* software defined ABI-relevant lowcore locations 0xe00 - 0xe20 */
 	OFFSET(__LC_DUMP_REIPL, lowcore, ipib);
 	/* hardware defined lowcore locations 0x1000 - 0x18ff */

arch/s390/kernel/base.S

@@ -9,18 +9,22 @@
 
 #include <linux/linkage.h>
 #include <asm/asm-offsets.h>
+#include <asm/nospec-insn.h>
 #include <asm/ptrace.h>
 #include <asm/sigp.h>
 
+	GEN_BR_THUNK %r9
+	GEN_BR_THUNK %r14
+
 ENTRY(s390_base_mcck_handler)
 	basr	%r13,0
 0:	lg	%r15,__LC_PANIC_STACK	# load panic stack
 	aghi	%r15,-STACK_FRAME_OVERHEAD
 	larl	%r1,s390_base_mcck_handler_fn
-	lg	%r1,0(%r1)
-	ltgr	%r1,%r1
+	lg	%r9,0(%r1)
+	ltgr	%r9,%r9
 	jz	1f
-	basr	%r14,%r1
+	BASR_EX	%r14,%r9
 1:	la	%r1,4095
 	lmg	%r0,%r15,__LC_GPREGS_SAVE_AREA-4095(%r1)
 	lpswe	__LC_MCK_OLD_PSW
@@ -37,10 +41,10 @@ ENTRY(s390_base_ext_handler)
 	basr	%r13,0
 0:	aghi	%r15,-STACK_FRAME_OVERHEAD
 	larl	%r1,s390_base_ext_handler_fn
-	lg	%r1,0(%r1)
-	ltgr	%r1,%r1
+	lg	%r9,0(%r1)
+	ltgr	%r9,%r9
 	jz	1f
-	basr	%r14,%r1
+	BASR_EX	%r14,%r9
 1:	lmg	%r0,%r15,__LC_SAVE_AREA_ASYNC
 	ni	__LC_EXT_OLD_PSW+1,0xfd	# clear wait state bit
 	lpswe	__LC_EXT_OLD_PSW
@@ -57,10 +61,10 @@ ENTRY(s390_base_pgm_handler)
 	basr	%r13,0
 0:	aghi	%r15,-STACK_FRAME_OVERHEAD
 	larl	%r1,s390_base_pgm_handler_fn
-	lg	%r1,0(%r1)
-	ltgr	%r1,%r1
+	lg	%r9,0(%r1)
+	ltgr	%r9,%r9
 	jz	1f
-	basr	%r14,%r1
+	BASR_EX	%r14,%r9
 	lmg	%r0,%r15,__LC_SAVE_AREA_SYNC
 	lpswe	__LC_PGM_OLD_PSW
 1:	lpswe	disabled_wait_psw-0b(%r13)
@@ -117,7 +121,7 @@ ENTRY(diag308_reset)
 	larl	%r4,.Lcontinue_psw	# Restore PSW flags
 	lpswe	0(%r4)
 .Lcontinue:
-	br	%r14
+	BR_EX	%r14
 .align 16
 .Lrestart_psw:
 	.long	0x00080000,0x80000000 + .Lrestart_part2

arch/s390/kernel/entry.S

@@ -28,6 +28,7 @@
 #include <asm/setup.h>
 #include <asm/nmi.h>
 #include <asm/export.h>
+#include <asm/nospec-insn.h>
 
 __PT_R0      =	__PT_GPRS
 __PT_R1      =	__PT_GPRS + 8
@@ -183,67 +184,9 @@ _LPP_OFFSET	= __LC_LPP
 		    "jnz .+8; .long 0xb2e8d000", 82
 	.endm
 
-#ifdef CONFIG_EXPOLINE
-
-	.macro GEN_BR_THUNK name,reg,tmp
-	.section .text.\name,"axG",@progbits,\name,comdat
-	.globl \name
-	.hidden \name
-	.type \name,@function
-\name:
-	CFI_STARTPROC
-#ifdef CONFIG_HAVE_MARCH_Z10_FEATURES
-	exrl	0,0f
-#else
-	larl	\tmp,0f
-	ex	0,0(\tmp)
-#endif
-	j	.
-0:	br	\reg
-	CFI_ENDPROC
-	.endm
-
-	GEN_BR_THUNK __s390x_indirect_jump_r1use_r9,%r9,%r1
-	GEN_BR_THUNK __s390x_indirect_jump_r1use_r14,%r14,%r1
-	GEN_BR_THUNK __s390x_indirect_jump_r11use_r14,%r14,%r11
-
-	.macro BASR_R14_R9
-0:	brasl	%r14,__s390x_indirect_jump_r1use_r9
-	.pushsection .s390_indirect_branches,"a",@progbits
-	.long	0b-.
-	.popsection
-	.endm
-
-	.macro BR_R1USE_R14
-0:	jg	__s390x_indirect_jump_r1use_r14
-	.pushsection .s390_indirect_branches,"a",@progbits
-	.long	0b-.
-	.popsection
-	.endm
-
-	.macro BR_R11USE_R14
-0:	jg	__s390x_indirect_jump_r11use_r14
-	.pushsection .s390_indirect_branches,"a",@progbits
-	.long	0b-.
-	.popsection
-	.endm
-
-#else	/* CONFIG_EXPOLINE */
-
-	.macro BASR_R14_R9
-	basr	%r14,%r9
-	.endm
-
-	.macro BR_R1USE_R14
-	br	%r14
-	.endm
-
-	.macro BR_R11USE_R14
-	br	%r14
-	.endm
-
-#endif /* CONFIG_EXPOLINE */
-
+	GEN_BR_THUNK %r9
+	GEN_BR_THUNK %r14
+	GEN_BR_THUNK %r14,%r11
 
 	.section .kprobes.text, "ax"
 .Ldummy:
@@ -260,7 +203,7 @@ _LPP_OFFSET	= __LC_LPP
 ENTRY(__bpon)
 	.globl __bpon
 	BPON
-	BR_R1USE_R14
+	BR_EX	%r14
 
 /*
  * Scheduler resume function, called by switch_to
@@ -284,7 +227,7 @@ ENTRY(__switch_to)
 	mvc	__LC_CURRENT_PID(4,%r0),0(%r3)	# store pid of next
 	lmg	%r6,%r15,__SF_GPRS(%r15)	# load gprs of next task
 	ALTERNATIVE "", ".insn s,0xb2800000,_LPP_OFFSET", 40
-	BR_R1USE_R14
+	BR_EX	%r14
 
 .L__critical_start:
 
@@ -351,7 +294,7 @@ sie_exit:
 	xgr	%r5,%r5
 	lmg	%r6,%r14,__SF_GPRS(%r15)	# restore kernel registers
 	lg	%r2,__SF_SIE_REASON(%r15)	# return exit reason code
-	BR_R1USE_R14
+	BR_EX	%r14
 .Lsie_fault:
 	lghi	%r14,-EFAULT
 	stg	%r14,__SF_SIE_REASON(%r15)	# set exit reason code
@@ -410,7 +353,7 @@ ENTRY(system_call)
 	lgf	%r9,0(%r8,%r10)			# get system call add.
 	TSTMSK	__TI_flags(%r12),_TIF_TRACE
 	jnz	.Lsysc_tracesys
-	BASR_R14_R9				# call sys_xxxx
+	BASR_EX	%r14,%r9			# call sys_xxxx
 	stg	%r2,__PT_R2(%r11)		# store return value
 
 .Lsysc_return:
@@ -595,7 +538,7 @@ ENTRY(system_call)
 	lmg	%r3,%r7,__PT_R3(%r11)
 	stg	%r7,STACK_FRAME_OVERHEAD(%r15)
 	lg	%r2,__PT_ORIG_GPR2(%r11)
-	BASR_R14_R9			# call sys_xxx
+	BASR_EX	%r14,%r9		# call sys_xxx
 	stg	%r2,__PT_R2(%r11)	# store return value
 .Lsysc_tracenogo:
 	TSTMSK	__TI_flags(%r12),_TIF_TRACE
@@ -619,7 +562,7 @@ ENTRY(ret_from_fork)
 	lmg	%r9,%r10,__PT_R9(%r11)	# load gprs
 ENTRY(kernel_thread_starter)
 	la	%r2,0(%r10)
-	BASR_R14_R9
+	BASR_EX	%r14,%r9
 	j	.Lsysc_tracenogo
 
 /*
@@ -701,7 +644,7 @@ ENTRY(pgm_check_handler)
 	je	.Lpgm_return
 	lgf	%r9,0(%r10,%r1)		# load address of handler routine
 	lgr	%r2,%r11		# pass pointer to pt_regs
-	BASR_R14_R9			# branch to interrupt-handler
+	BASR_EX	%r14,%r9		# branch to interrupt-handler
 .Lpgm_return:
 	LOCKDEP_SYS_EXIT
 	tm	__PT_PSW+1(%r11),0x01	# returning to user ?
@@ -1019,7 +962,7 @@ ENTRY(psw_idle)
 	stpt	__TIMER_IDLE_ENTER(%r2)
 .Lpsw_idle_lpsw:
 	lpswe	__SF_EMPTY(%r15)
-	BR_R1USE_R14
+	BR_EX	%r14
 .Lpsw_idle_end:
 
 /*
@@ -1061,7 +1004,7 @@ ENTRY(save_fpu_regs)
 .Lsave_fpu_regs_done:
 	oi	__LC_CPU_FLAGS+7,_CIF_FPU
 .Lsave_fpu_regs_exit:
-	BR_R1USE_R14
+	BR_EX	%r14
 .Lsave_fpu_regs_end:
 EXPORT_SYMBOL(save_fpu_regs)
 
@@ -1107,7 +1050,7 @@ load_fpu_regs:
 .Lload_fpu_regs_done:
 	ni	__LC_CPU_FLAGS+7,255-_CIF_FPU
 .Lload_fpu_regs_exit:
-	BR_R1USE_R14
+	BR_EX	%r14
 .Lload_fpu_regs_end:
 
 .L__critical_end:
@@ -1322,7 +1265,7 @@ cleanup_critical:
 	jl	0f
 	clg	%r9,BASED(.Lcleanup_table+104)	# .Lload_fpu_regs_end
 	jl	.Lcleanup_load_fpu_regs
-0:	BR_R11USE_R14
+0:	BR_EX	%r14
 
 	.align	8
 .Lcleanup_table:
@@ -1358,7 +1301,7 @@ cleanup_critical:
 	ni	__SIE_PROG0C+3(%r9),0xfe	# no longer in SIE
 	lctlg	%c1,%c1,__LC_USER_ASCE		# load primary asce
 	larl	%r9,sie_exit			# skip forward to sie_exit
-	BR_R11USE_R14
+	BR_EX	%r14
 #endif
 
 .Lcleanup_system_call:
@@ -1412,7 +1355,7 @@ cleanup_critical:
 	stg	%r15,56(%r11)		# r15 stack pointer
 	# set new psw address and exit
 	larl	%r9,.Lsysc_do_svc
-	BR_R11USE_R14
+	BR_EX	%r14,%r11
 .Lcleanup_system_call_insn:
 	.quad	system_call
 	.quad	.Lsysc_stmg
@@ -1424,7 +1367,7 @@ cleanup_critical:
 
 .Lcleanup_sysc_tif:
 	larl	%r9,.Lsysc_tif
-	BR_R11USE_R14
+	BR_EX	%r14,%r11
 
 .Lcleanup_sysc_restore:
 	# check if stpt has been executed
@@ -1441,14 +1384,14 @@ cleanup_critical:
 	mvc	0(64,%r11),__PT_R8(%r9)
 	lmg	%r0,%r7,__PT_R0(%r9)
 1:	lmg	%r8,%r9,__LC_RETURN_PSW
-	BR_R11USE_R14
+	BR_EX	%r14,%r11
 .Lcleanup_sysc_restore_insn:
 	.quad	.Lsysc_exit_timer
 	.quad	.Lsysc_done - 4
 
 .Lcleanup_io_tif:
 	larl	%r9,.Lio_tif
-	BR_R11USE_R14
+	BR_EX	%r14,%r11
 
 .Lcleanup_io_restore:
 	# check if stpt has been executed
@@ -1462,7 +1405,7 @@ cleanup_critical:
 	mvc	0(64,%r11),__PT_R8(%r9)
 	lmg	%r0,%r7,__PT_R0(%r9)
 1:	lmg	%r8,%r9,__LC_RETURN_PSW
-	BR_R11USE_R14
+	BR_EX	%r14,%r11
 .Lcleanup_io_restore_insn:
 	.quad	.Lio_exit_timer
 	.quad	.Lio_done - 4
@@ -1515,17 +1458,17 @@ cleanup_critical:
 	# prepare return psw
 	nihh	%r8,0xfcfd		# clear irq & wait state bits
 	lg	%r9,48(%r11)		# return from psw_idle
-	BR_R11USE_R14
+	BR_EX	%r14,%r11
 .Lcleanup_idle_insn:
 	.quad	.Lpsw_idle_lpsw
 
 .Lcleanup_save_fpu_regs:
 	larl	%r9,save_fpu_regs
-	BR_R11USE_R14
+	BR_EX	%r14,%r11
 
 .Lcleanup_load_fpu_regs:
 	larl	%r9,load_fpu_regs
-	BR_R11USE_R14
+	BR_EX	%r14,%r11
 
 /*
  * Integer constants

arch/s390/kernel/irq.c

@@ -176,10 +176,9 @@ void do_softirq_own_stack(void)
 		new -= STACK_FRAME_OVERHEAD;
 		((struct stack_frame *) new)->back_chain = old;
 		asm volatile("   la    15,0(%0)\n"
-			     "   basr  14,%2\n"
+			     "   brasl 14,__do_softirq\n"
 			     "   la    15,0(%1)\n"
-			     : : "a" (new), "a" (old),
-			         "a" (__do_softirq)
+			     : : "a" (new), "a" (old)
 			     : "0", "1", "2", "3", "4", "5", "14",
 			       "cc", "memory" );
 	} else {

arch/s390/kernel/mcount.S

@@ -9,13 +9,17 @@
 #include <linux/linkage.h>
 #include <asm/asm-offsets.h>
 #include <asm/ftrace.h>
+#include <asm/nospec-insn.h>
 #include <asm/ptrace.h>
 #include <asm/export.h>
 
+	GEN_BR_THUNK %r1
+	GEN_BR_THUNK %r14
+
 	.section .kprobes.text, "ax"
 
 ENTRY(ftrace_stub)
-	br	%r14
+	BR_EX	%r14
 
 #define STACK_FRAME_SIZE  (STACK_FRAME_OVERHEAD + __PT_SIZE)
 #define STACK_PTREGS	  (STACK_FRAME_OVERHEAD)
@@ -23,7 +27,7 @@ ENTRY(ftrace_stub)
 #define STACK_PTREGS_PSW  (STACK_PTREGS + __PT_PSW)
 
 ENTRY(_mcount)
-	br	%r14
+	BR_EX	%r14
 
 EXPORT_SYMBOL(_mcount)
 
@@ -53,7 +57,7 @@ ENTRY(ftrace_caller)
 #endif
 	lgr	%r3,%r14
 	la	%r5,STACK_PTREGS(%r15)
-	basr	%r14,%r1
+	BASR_EX	%r14,%r1
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
 # The j instruction gets runtime patched to a nop instruction.
 # See ftrace_enable_ftrace_graph_caller.
@@ -68,7 +72,7 @@ ftrace_graph_caller_end:
 #endif
 	lg	%r1,(STACK_PTREGS_PSW+8)(%r15)
 	lmg	%r2,%r15,(STACK_PTREGS_GPRS+2*8)(%r15)
-	br	%r1
+	BR_EX	%r1
 
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
 
@@ -81,6 +85,6 @@ ENTRY(return_to_handler)
 	aghi	%r15,STACK_FRAME_OVERHEAD
 	lgr	%r14,%r2
 	lmg	%r2,%r5,32(%r15)
-	br	%r14
+	BR_EX	%r14
 
 #endif

arch/s390/kernel/nospec-branch.c

@@ -1,7 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <linux/module.h>
 #include <linux/device.h>
-#include <linux/cpu.h>
 #include <asm/nospec-branch.h>
 
 static int __init nobp_setup_early(char *str)
@@ -44,24 +43,6 @@ static int __init nospec_report(void)
 }
 arch_initcall(nospec_report);
 
-#ifdef CONFIG_SYSFS
-ssize_t cpu_show_spectre_v1(struct device *dev,
-			    struct device_attribute *attr, char *buf)
-{
-	return sprintf(buf, "Mitigation: __user pointer sanitization\n");
-}
-
-ssize_t cpu_show_spectre_v2(struct device *dev,
-			    struct device_attribute *attr, char *buf)
-{
-	if (IS_ENABLED(CC_USING_EXPOLINE) && !nospec_disable)
-		return sprintf(buf, "Mitigation: execute trampolines\n");
-	if (__test_facility(82, S390_lowcore.alt_stfle_fac_list))
-		return sprintf(buf, "Mitigation: limited branch prediction.\n");
-	return sprintf(buf, "Vulnerable\n");
-}
-#endif
-
 #ifdef CONFIG_EXPOLINE
 
 int nospec_disable = IS_ENABLED(CONFIG_EXPOLINE_OFF);
@@ -112,7 +93,6 @@ static void __init_or_module __nospec_revert(s32 *start, s32 *end)
 	s32 *epo;
 
 	/* Second part of the instruction replace is always a nop */
-	memcpy(insnbuf + 2, (char[]) { 0x47, 0x00, 0x00, 0x00 }, 4);
 	for (epo = start; epo < end; epo++) {
 		instr = (u8 *) epo + *epo;
 		if (instr[0] == 0xc0 && (instr[1] & 0x0f) == 0x04)
@@ -133,18 +113,34 @@ static void __init_or_module __nospec_revert(s32 *start, s32 *end)
 			br = thunk + (*(int *)(thunk + 2)) * 2;
 		else
 			continue;
-		if (br[0] != 0x07 || (br[1] & 0xf0) != 0xf0)
+		/* Check for unconditional branch 0x07f? or 0x47f???? */
+		if ((br[0] & 0xbf) != 0x07 || (br[1] & 0xf0) != 0xf0)
 			continue;
+
+		memcpy(insnbuf + 2, (char[]) { 0x47, 0x00, 0x07, 0x00 }, 4);
 		switch (type) {
 		case BRCL_EXPOLINE:
-			/* brcl to thunk, replace with br + nop */
 			insnbuf[0] = br[0];
 			insnbuf[1] = (instr[1] & 0xf0) | (br[1] & 0x0f);
+			if (br[0] == 0x47) {
+				/* brcl to b, replace with bc + nopr */
+				insnbuf[2] = br[2];
+				insnbuf[3] = br[3];
+			} else {
+				/* brcl to br, replace with bcr + nop */
+			}
 			break;
 		case BRASL_EXPOLINE:
-			/* brasl to thunk, replace with basr + nop */
-			insnbuf[0] = 0x0d;
 			insnbuf[1] = (instr[1] & 0xf0) | (br[1] & 0x0f);
+			if (br[0] == 0x47) {
+				/* brasl to b, replace with bas + nopr */
+				insnbuf[0] = 0x4d;
+				insnbuf[2] = br[2];
+				insnbuf[3] = br[3];
+			} else {
+				/* brasl to br, replace with basr + nop */
+				insnbuf[0] = 0x0d;
+			}
 			break;
 		}
 

arch/s390/kernel/nospec-sysfs.c

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/device.h>
+#include <linux/cpu.h>
+#include <asm/facility.h>
+#include <asm/nospec-branch.h>
+
+ssize_t cpu_show_spectre_v1(struct device *dev,
+			    struct device_attribute *attr, char *buf)
+{
+	return sprintf(buf, "Mitigation: __user pointer sanitization\n");
+}
+
+ssize_t cpu_show_spectre_v2(struct device *dev,
+			    struct device_attribute *attr, char *buf)
+{
+	if (IS_ENABLED(CC_USING_EXPOLINE) && !nospec_disable)
+		return sprintf(buf, "Mitigation: execute trampolines\n");
+	if (__test_facility(82, S390_lowcore.alt_stfle_fac_list))
+		return sprintf(buf, "Mitigation: limited branch prediction\n");
+	return sprintf(buf, "Vulnerable\n");
+}

arch/s390/kernel/perf_cpum_sf.c

@@ -753,6 +753,10 @@ static int __hw_perf_event_init(struct perf_event *event)
 	 */
 	rate = 0;
 	if (attr->freq) {
+		if (!attr->sample_freq) {
+			err = -EINVAL;
+			goto out;
+		}
 		rate = freq_to_sample_rate(&si, attr->sample_freq);
 		rate = hw_limit_rate(&si, rate);
 		attr->freq = 0;

arch/s390/kernel/reipl.S

@@ -7,8 +7,11 @@
 
 #include <linux/linkage.h>
 #include <asm/asm-offsets.h>
+#include <asm/nospec-insn.h>
 #include <asm/sigp.h>
 
+	GEN_BR_THUNK %r9
+
 #
 # Issue "store status" for the current CPU to its prefix page
 # and call passed function afterwards
@@ -67,9 +70,9 @@ ENTRY(store_status)
 	st	%r4,0(%r1)
 	st	%r5,4(%r1)
 	stg	%r2,8(%r1)
-	lgr	%r1,%r2
+	lgr	%r9,%r2
 	lgr	%r2,%r3
-	br	%r1
+	BR_EX	%r9
 
 	.section .bss
 	.align	8

arch/s390/kernel/swsusp.S

@@ -13,6 +13,7 @@
 #include <asm/ptrace.h>
 #include <asm/thread_info.h>
 #include <asm/asm-offsets.h>
+#include <asm/nospec-insn.h>
 #include <asm/sigp.h>
 
 /*
@@ -24,6 +25,8 @@
  * (see below) in the resume process.
  * This function runs with disabled interrupts.
  */
+	GEN_BR_THUNK %r14
+
 	.section .text
 ENTRY(swsusp_arch_suspend)
 	stmg	%r6,%r15,__SF_GPRS(%r15)
@@ -103,7 +106,7 @@ ENTRY(swsusp_arch_suspend)
 	spx	0x318(%r1)
 	lmg	%r6,%r15,STACK_FRAME_OVERHEAD + __SF_GPRS(%r15)
 	lghi	%r2,0
-	br	%r14
+	BR_EX	%r14
 
 /*
  * Restore saved memory image to correct place and restore register context.
@@ -197,11 +200,10 @@ pgm_check_entry:
 	larl	%r15,init_thread_union
 	ahi	%r15,1<<(PAGE_SHIFT+THREAD_SIZE_ORDER)
 	larl	%r2,.Lpanic_string
-	larl	%r3,sclp_early_printk
 	lghi	%r1,0
 	sam31
 	sigp	%r1,%r0,SIGP_SET_ARCHITECTURE
-	basr	%r14,%r3
+	brasl	%r14,sclp_early_printk
 	larl	%r3,.Ldisabled_wait_31
 	lpsw	0(%r3)
 4:
@@ -267,7 +269,7 @@ restore_registers:
 	/* Return 0 */
 	lmg	%r6,%r15,STACK_FRAME_OVERHEAD + __SF_GPRS(%r15)
 	lghi	%r2,0
-	br	%r14
+	BR_EX	%r14
 
 	.section .data..nosave,"aw",@progbits
 	.align	8

arch/s390/lib/mem.S

@@ -7,6 +7,9 @@
 
 #include <linux/linkage.h>
 #include <asm/export.h>
+#include <asm/nospec-insn.h>
+
+	GEN_BR_THUNK %r14
 
 /*
  * void *memmove(void *dest, const void *src, size_t n)
@@ -33,14 +36,14 @@ ENTRY(memmove)
 .Lmemmove_forward_remainder:
 	larl	%r5,.Lmemmove_mvc
 	ex	%r4,0(%r5)
-	br	%r14
+	BR_EX	%r14
 .Lmemmove_reverse:
 	ic	%r0,0(%r4,%r3)
 	stc	%r0,0(%r4,%r1)
 	brctg	%r4,.Lmemmove_reverse
 	ic	%r0,0(%r4,%r3)
 	stc	%r0,0(%r4,%r1)
-	br	%r14
+	BR_EX	%r14
 .Lmemmove_mvc:
 	mvc	0(1,%r1),0(%r3)
 EXPORT_SYMBOL(memmove)
@@ -77,7 +80,7 @@ ENTRY(memset)
 .Lmemset_clear_remainder:
 	larl	%r3,.Lmemset_xc
 	ex	%r4,0(%r3)
-	br	%r14
+	BR_EX	%r14
 .Lmemset_fill:
 	cghi	%r4,1
 	lgr	%r1,%r2
@@ -95,10 +98,10 @@ ENTRY(memset)
 	stc	%r3,0(%r1)
 	larl	%r5,.Lmemset_mvc
 	ex	%r4,0(%r5)
-	br	%r14
+	BR_EX	%r14
 .Lmemset_fill_exit:
 	stc	%r3,0(%r1)
-	br	%r14
+	BR_EX	%r14
 .Lmemset_xc:
 	xc	0(1,%r1),0(%r1)
 .Lmemset_mvc:
@@ -121,7 +124,7 @@ ENTRY(memcpy)
 .Lmemcpy_remainder:
 	larl	%r5,.Lmemcpy_mvc
 	ex	%r4,0(%r5)
-	br	%r14
+	BR_EX	%r14
 .Lmemcpy_loop:
 	mvc	0(256,%r1),0(%r3)
 	la	%r1,256(%r1)
@@ -159,10 +162,10 @@ ENTRY(__memset\bits)
 	\insn	%r3,0(%r1)
 	larl	%r5,.L__memset_mvc\bits
 	ex	%r4,0(%r5)
-	br	%r14
+	BR_EX	%r14
 .L__memset_exit\bits:
 	\insn	%r3,0(%r2)
-	br	%r14
+	BR_EX	%r14
 .L__memset_mvc\bits:
 	mvc	\bytes(1,%r1),0(%r1)
 .endm

arch/s390/net/bpf_jit.S

@@ -9,6 +9,7 @@
  */
 
 #include <linux/linkage.h>
+#include <asm/nospec-insn.h>
 #include "bpf_jit.h"
 
 /*
@@ -54,7 +55,7 @@ ENTRY(sk_load_##NAME##_pos);						\
 	clg	%r3,STK_OFF_HLEN(%r15);	/* Offset + SIZE > hlen? */	\
 	jh	sk_load_##NAME##_slow;					\
 	LOAD	%r14,-SIZE(%r3,%r12);	/* Get data from skb */		\
-	b	OFF_OK(%r6);		/* Return */			\
+	B_EX	OFF_OK,%r6;		/* Return */			\
 									\
 sk_load_##NAME##_slow:;							\
 	lgr	%r2,%r7;		/* Arg1 = skb pointer */	\
@@ -64,11 +65,14 @@ sk_load_##NAME##_slow:;							\
 	brasl	%r14,skb_copy_bits;	/* Get data from skb */		\
 	LOAD	%r14,STK_OFF_TMP(%r15);	/* Load from temp bufffer */	\
 	ltgr	%r2,%r2;		/* Set cc to (%r2 != 0) */	\
-	br	%r6;			/* Return */
+	BR_EX	%r6;			/* Return */
 
 sk_load_common(word, 4, llgf)	/* r14 = *(u32 *) (skb->data+offset) */
 sk_load_common(half, 2, llgh)	/* r14 = *(u16 *) (skb->data+offset) */
 
+	GEN_BR_THUNK %r6
+	GEN_B_THUNK OFF_OK,%r6
+
 /*
  * Load 1 byte from SKB (optimized version)
  */
@@ -80,7 +84,7 @@ ENTRY(sk_load_byte_pos)
 	clg	%r3,STK_OFF_HLEN(%r15)	# Offset >= hlen?
 	jnl	sk_load_byte_slow
 	llgc	%r14,0(%r3,%r12)	# Get byte from skb
-	b	OFF_OK(%r6)		# Return OK
+	B_EX	OFF_OK,%r6		# Return OK
 
 sk_load_byte_slow:
 	lgr	%r2,%r7			# Arg1 = skb pointer
@@ -90,7 +94,7 @@ sk_load_byte_slow:
 	brasl	%r14,skb_copy_bits	# Get data from skb
 	llgc	%r14,STK_OFF_TMP(%r15)	# Load result from temp buffer
 	ltgr	%r2,%r2			# Set cc to (%r2 != 0)
-	br	%r6			# Return cc
+	BR_EX	%r6			# Return cc
 
 #define sk_negative_common(NAME, SIZE, LOAD)				\
 sk_load_##NAME##_slow_neg:;						\
@@ -104,7 +108,7 @@ sk_load_##NAME##_slow_neg:;						\
 	jz	bpf_error;						\
 	LOAD	%r14,0(%r2);		/* Get data from pointer */	\
 	xr	%r3,%r3;		/* Set cc to zero */		\
-	br	%r6;			/* Return cc */
+	BR_EX	%r6;			/* Return cc */
 
 sk_negative_common(word, 4, llgf)
 sk_negative_common(half, 2, llgh)
@@ -113,4 +117,4 @@ sk_negative_common(byte, 1, llgc)
 bpf_error:
 # force a return 0 from jit handler
 	ltgr	%r15,%r15	# Set condition code
-	br	%r6
+	BR_EX	%r6

arch/s390/net/bpf_jit_comp.c

@@ -25,6 +25,8 @@
 #include <linux/bpf.h>
 #include <asm/cacheflush.h>
 #include <asm/dis.h>
+#include <asm/facility.h>
+#include <asm/nospec-branch.h>
 #include <asm/set_memory.h>
 #include "bpf_jit.h"
 
@@ -41,6 +43,8 @@ struct bpf_jit {
 	int base_ip;		/* Base address for literal pool */
 	int ret0_ip;		/* Address of return 0 */
 	int exit_ip;		/* Address of exit */
+	int r1_thunk_ip;	/* Address of expoline thunk for 'br %r1' */
+	int r14_thunk_ip;	/* Address of expoline thunk for 'br %r14' */
 	int tail_call_start;	/* Tail call start offset */
 	int labels[1];		/* Labels for local jumps */
 };
@@ -250,6 +254,19 @@ static inline void reg_set_seen(struct bpf_jit *jit, u32 b1)
 	REG_SET_SEEN(b2);					\
 })
 
+#define EMIT6_PCREL_RILB(op, b, target)				\
+({								\
+	int rel = (target - jit->prg) / 2;			\
+	_EMIT6(op | reg_high(b) << 16 | rel >> 16, rel & 0xffff);	\
+	REG_SET_SEEN(b);					\
+})
+
+#define EMIT6_PCREL_RIL(op, target)				\
+({								\
+	int rel = (target - jit->prg) / 2;			\
+	_EMIT6(op | rel >> 16, rel & 0xffff);			\
+})
+
 #define _EMIT6_IMM(op, imm)					\
 ({								\
 	unsigned int __imm = (imm);				\
@@ -469,8 +486,45 @@ static void bpf_jit_epilogue(struct bpf_jit *jit, u32 stack_depth)
 	EMIT4(0xb9040000, REG_2, BPF_REG_0);
 	/* Restore registers */
 	save_restore_regs(jit, REGS_RESTORE, stack_depth);
+	if (IS_ENABLED(CC_USING_EXPOLINE) && !nospec_disable) {
+		jit->r14_thunk_ip = jit->prg;
+		/* Generate __s390_indirect_jump_r14 thunk */
+		if (test_facility(35)) {
+			/* exrl %r0,.+10 */
+			EMIT6_PCREL_RIL(0xc6000000, jit->prg + 10);
+		} else {
+			/* larl %r1,.+14 */
+			EMIT6_PCREL_RILB(0xc0000000, REG_1, jit->prg + 14);
+			/* ex 0,0(%r1) */
+			EMIT4_DISP(0x44000000, REG_0, REG_1, 0);
+		}
+		/* j . */
+		EMIT4_PCREL(0xa7f40000, 0);
+	}
 	/* br %r14 */
 	_EMIT2(0x07fe);
+
+	if (IS_ENABLED(CC_USING_EXPOLINE) && !nospec_disable &&
+	    (jit->seen & SEEN_FUNC)) {
+		jit->r1_thunk_ip = jit->prg;
+		/* Generate __s390_indirect_jump_r1 thunk */
+		if (test_facility(35)) {
+			/* exrl %r0,.+10 */
+			EMIT6_PCREL_RIL(0xc6000000, jit->prg + 10);
+			/* j . */
+			EMIT4_PCREL(0xa7f40000, 0);
+			/* br %r1 */
+			_EMIT2(0x07f1);
+		} else {
+			/* larl %r1,.+14 */
+			EMIT6_PCREL_RILB(0xc0000000, REG_1, jit->prg + 14);
+			/* ex 0,S390_lowcore.br_r1_tampoline */
+			EMIT4_DISP(0x44000000, REG_0, REG_0,
+				   offsetof(struct lowcore, br_r1_trampoline));
+			/* j . */
+			EMIT4_PCREL(0xa7f40000, 0);
+		}
+	}
 }
 
 /*
@@ -966,8 +1020,13 @@ static noinline int bpf_jit_insn(struct bpf_jit *jit, struct bpf_prog *fp, int i
 		/* lg %w1,<d(imm)>(%l) */
 		EMIT6_DISP_LH(0xe3000000, 0x0004, REG_W1, REG_0, REG_L,
 			      EMIT_CONST_U64(func));
-		/* basr %r14,%w1 */
-		EMIT2(0x0d00, REG_14, REG_W1);
+		if (IS_ENABLED(CC_USING_EXPOLINE) && !nospec_disable) {
+			/* brasl %r14,__s390_indirect_jump_r1 */
+			EMIT6_PCREL_RILB(0xc0050000, REG_14, jit->r1_thunk_ip);
+		} else {
+			/* basr %r14,%w1 */
+			EMIT2(0x0d00, REG_14, REG_W1);
+		}
 		/* lgr %b0,%r2: load return value into %b0 */
 		EMIT4(0xb9040000, BPF_REG_0, REG_2);
 		if ((jit->seen & SEEN_SKB) &&

arch/sh/Kconfig

@@ -9,6 +9,7 @@ config SUPERH
 	select HAVE_IDE if HAS_IOPORT_MAP
 	select HAVE_MEMBLOCK
 	select HAVE_MEMBLOCK_NODE_MAP
+	select NO_BOOTMEM
 	select ARCH_DISCARD_MEMBLOCK
 	select HAVE_OPROFILE
 	select HAVE_GENERIC_DMA_COHERENT

arch/sh/kernel/cpu/sh2/probe.c

@@ -43,7 +43,11 @@ void __ref cpu_probe(void)
 #endif
 
 #if defined(CONFIG_CPU_J2)
+#if defined(CONFIG_SMP)
 	unsigned cpu = hard_smp_processor_id();
+#else
+	unsigned cpu = 0;
+#endif
 	if (cpu == 0) of_scan_flat_dt(scan_cache, NULL);
 	if (j2_ccr_base) __raw_writel(0x80000303, j2_ccr_base + 4*cpu);
 	if (cpu != 0) return;

arch/sh/kernel/setup.c

@@ -11,7 +11,6 @@
 #include <linux/ioport.h>
 #include <linux/init.h>
 #include <linux/initrd.h>
-#include <linux/bootmem.h>
 #include <linux/console.h>
 #include <linux/root_dev.h>
 #include <linux/utsname.h>

arch/sh/mm/consistent.c

@@ -59,7 +59,9 @@ void *dma_generic_alloc_coherent(struct device *dev, size_t size,
 
 	split_page(pfn_to_page(virt_to_phys(ret) >> PAGE_SHIFT), order);
 
-	*dma_handle = virt_to_phys(ret) - PFN_PHYS(dev->dma_pfn_offset);
+	*dma_handle = virt_to_phys(ret);
+	if (!WARN_ON(!dev))
+		*dma_handle -= PFN_PHYS(dev->dma_pfn_offset);
 
 	return ret_nocache;
 }
@@ -69,9 +71,12 @@ void dma_generic_free_coherent(struct device *dev, size_t size,
 			       unsigned long attrs)
 {
 	int order = get_order(size);
-	unsigned long pfn = (dma_handle >> PAGE_SHIFT) + dev->dma_pfn_offset;
+	unsigned long pfn = dma_handle >> PAGE_SHIFT;
 	int k;
 
+	if (!WARN_ON(!dev))
+		pfn += dev->dma_pfn_offset;
+
 	for (k = 0; k < (1 << order); k++)
 		__free_pages(pfn_to_page(pfn + k), 0);
 
@@ -143,7 +148,7 @@ int __init platform_resource_setup_memory(struct platform_device *pdev,
 	if (!memsize)
 		return 0;
 
-	buf = dma_alloc_coherent(NULL, memsize, &dma_handle, GFP_KERNEL);
+	buf = dma_alloc_coherent(&pdev->dev, memsize, &dma_handle, GFP_KERNEL);
 	if (!buf) {
 		pr_warning("%s: unable to allocate memory\n", name);
 		return -ENOMEM;

arch/sh/mm/init.c

@@ -211,59 +211,15 @@ void __init allocate_pgdat(unsigned int nid)
 
 	NODE_DATA(nid) = __va(phys);
 	memset(NODE_DATA(nid), 0, sizeof(struct pglist_data));
-
-	NODE_DATA(nid)->bdata = &bootmem_node_data[nid];
 #endif
 
 	NODE_DATA(nid)->node_start_pfn = start_pfn;
 	NODE_DATA(nid)->node_spanned_pages = end_pfn - start_pfn;
 }
 
-static void __init bootmem_init_one_node(unsigned int nid)
-{
-	unsigned long total_pages, paddr;
-	unsigned long end_pfn;
-	struct pglist_data *p;
-
-	p = NODE_DATA(nid);
-
-	/* Nothing to do.. */
-	if (!p->node_spanned_pages)
-		return;
-
-	end_pfn = pgdat_end_pfn(p);
-
-	total_pages = bootmem_bootmap_pages(p->node_spanned_pages);
-
-	paddr = memblock_alloc(total_pages << PAGE_SHIFT, PAGE_SIZE);
-	if (!paddr)
-		panic("Can't allocate bootmap for nid[%d]\n", nid);
-
-	init_bootmem_node(p, paddr >> PAGE_SHIFT, p->node_start_pfn, end_pfn);
-
-	free_bootmem_with_active_regions(nid, end_pfn);
-
-	/*
-	 * XXX Handle initial reservations for the system memory node
-	 * only for the moment, we'll refactor this later for handling
-	 * reservations in other nodes.
-	 */
-	if (nid == 0) {
-		struct memblock_region *reg;
-
-		/* Reserve the sections we're already using. */
-		for_each_memblock(reserved, reg) {
-			reserve_bootmem(reg->base, reg->size, BOOTMEM_DEFAULT);
-		}
-	}
-
-	sparse_memory_present_with_active_regions(nid);
-}
-
 static void __init do_init_bootmem(void)
 {
 	struct memblock_region *reg;
-	int i;
 
 	/* Add active regions with valid PFNs. */
 	for_each_memblock(memory, reg) {
@@ -279,9 +235,12 @@ static void __init do_init_bootmem(void)
 
 	plat_mem_setup();
 
-	for_each_online_node(i)
-		bootmem_init_one_node(i);
+	for_each_memblock(memory, reg) {
+		int nid = memblock_get_region_node(reg);
 
+		memory_present(nid, memblock_region_memory_base_pfn(reg),
+			memblock_region_memory_end_pfn(reg));
+	}
 	sparse_init();
 }
 
@@ -322,7 +281,6 @@ void __init paging_init(void)
 {
 	unsigned long max_zone_pfns[MAX_NR_ZONES];
 	unsigned long vaddr, end;
-	int nid;
 
 	sh_mv.mv_mem_init();
 
@@ -377,21 +335,7 @@ void __init paging_init(void)
 	kmap_coherent_init();
 
 	memset(max_zone_pfns, 0, sizeof(max_zone_pfns));
-
-	for_each_online_node(nid) {
-		pg_data_t *pgdat = NODE_DATA(nid);
-		unsigned long low, start_pfn;
-
-		start_pfn = pgdat->bdata->node_min_pfn;
-		low = pgdat->bdata->node_low_pfn;
-
-		if (max_zone_pfns[ZONE_NORMAL] < low)
-			max_zone_pfns[ZONE_NORMAL] = low;
-
-		printk("Node %u: start_pfn = 0x%lx, low = 0x%lx\n",
-		       nid, start_pfn, low);
-	}
-
+	max_zone_pfns[ZONE_NORMAL] = max_low_pfn;
 	free_area_init_nodes(max_zone_pfns);
 }