Merge branch 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson

* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  mach-ux500: configure board for the TPS61052 regulator v2
  mach-ux500: provide ab8500 init vector
  mach-ux500: board support for AB8500 GPIO driver
  gpio: driver for 42 AB8500 GPIO pins

arch/arm/mach-ux500/Kconfig

@@ -23,6 +23,7 @@ menu "Ux500 target platform"
 config MACH_U8500
 	bool "U8500 Development platform"
 	depends on UX500_SOC_DB8500
+	select TPS6105X
 	help
 	  Include support for the mop500 development platform.
 

arch/arm/mach-ux500/board-mop500-regulators.c

@@ -13,6 +13,30 @@
 #include <linux/regulator/ab8500.h>
 #include "board-mop500-regulators.h"
 
+/*
+ * TPS61052 regulator
+ */
+static struct regulator_consumer_supply tps61052_vaudio_consumers[] = {
+	/*
+	 * Boost converter supply to raise voltage on audio speaker, this
+	 * is actually connected to three pins, VInVhfL (left amplifier)
+	 * VInVhfR (right amplifier) and VIntDClassInt - all three must
+	 * be connected to the same voltage.
+	 */
+	REGULATOR_SUPPLY("vintdclassint", "ab8500-codec.0"),
+};
+
+struct regulator_init_data tps61052_regulator = {
+	.constraints = {
+		.name = "vaudio-hf",
+		.min_uV = 4500000,
+		.max_uV = 4500000,
+		.valid_ops_mask = REGULATOR_CHANGE_STATUS,
+	},
+	.num_consumer_supplies = ARRAY_SIZE(tps61052_vaudio_consumers),
+	.consumer_supplies = tps61052_vaudio_consumers,
+};
+
 static struct regulator_consumer_supply ab8500_vaux1_consumers[] = {
 	/* External displays, connector on board 2v5 power supply */
 	REGULATOR_SUPPLY("vaux12v5", "mcde.0"),
@@ -62,6 +86,182 @@ static struct regulator_consumer_supply ab8500_vana_consumers[] = {
 	REGULATOR_SUPPLY("vsmps2", "mcde.0"),
 };
 
+/* ab8500 regulator register initialization */
+struct ab8500_regulator_reg_init
+ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS] = {
+	/*
+	 * VanaRequestCtrl          = HP/LP depending on VxRequest
+	 * VextSupply1RequestCtrl   = HP/LP depending on VxRequest
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL2, 0x00),
+	/*
+	 * VextSupply2RequestCtrl   = HP/LP depending on VxRequest
+	 * VextSupply3RequestCtrl   = HP/LP depending on VxRequest
+	 * Vaux1RequestCtrl         = HP/LP depending on VxRequest
+	 * Vaux2RequestCtrl         = HP/LP depending on VxRequest
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL3, 0x00),
+	/*
+	 * Vaux3RequestCtrl         = HP/LP depending on VxRequest
+	 * SwHPReq                  = Control through SWValid disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUREQUESTCTRL4, 0x00),
+	/*
+	 * VanaSysClkReq1HPValid    = disabled
+	 * Vaux1SysClkReq1HPValid   = disabled
+	 * Vaux2SysClkReq1HPValid   = disabled
+	 * Vaux3SysClkReq1HPValid   = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQ1HPVALID1, 0x00),
+	/*
+	 * VextSupply1SysClkReq1HPValid = disabled
+	 * VextSupply2SysClkReq1HPValid = disabled
+	 * VextSupply3SysClkReq1HPValid = SysClkReq1 controlled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQ1HPVALID2, 0x40),
+	/*
+	 * VanaHwHPReq1Valid        = disabled
+	 * Vaux1HwHPreq1Valid       = disabled
+	 * Vaux2HwHPReq1Valid       = disabled
+	 * Vaux3HwHPReqValid        = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ1VALID1, 0x00),
+	/*
+	 * VextSupply1HwHPReq1Valid = disabled
+	 * VextSupply2HwHPReq1Valid = disabled
+	 * VextSupply3HwHPReq1Valid = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ1VALID2, 0x00),
+	/*
+	 * VanaHwHPReq2Valid        = disabled
+	 * Vaux1HwHPReq2Valid       = disabled
+	 * Vaux2HwHPReq2Valid       = disabled
+	 * Vaux3HwHPReq2Valid       = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ2VALID1, 0x00),
+	/*
+	 * VextSupply1HwHPReq2Valid = disabled
+	 * VextSupply2HwHPReq2Valid = disabled
+	 * VextSupply3HwHPReq2Valid = HWReq2 controlled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUHWHPREQ2VALID2, 0x04),
+	/*
+	 * VanaSwHPReqValid         = disabled
+	 * Vaux1SwHPReqValid        = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUSWHPREQVALID1, 0x00),
+	/*
+	 * Vaux2SwHPReqValid        = disabled
+	 * Vaux3SwHPReqValid        = disabled
+	 * VextSupply1SwHPReqValid  = disabled
+	 * VextSupply2SwHPReqValid  = disabled
+	 * VextSupply3SwHPReqValid  = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUSWHPREQVALID2, 0x00),
+	/*
+	 * SysClkReq2Valid1         = SysClkReq2 controlled
+	 * SysClkReq3Valid1         = disabled
+	 * SysClkReq4Valid1         = SysClkReq4 controlled
+	 * SysClkReq5Valid1         = disabled
+	 * SysClkReq6Valid1         = SysClkReq6 controlled
+	 * SysClkReq7Valid1         = disabled
+	 * SysClkReq8Valid1         = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQVALID1, 0x2a),
+	/*
+	 * SysClkReq2Valid2         = disabled
+	 * SysClkReq3Valid2         = disabled
+	 * SysClkReq4Valid2         = disabled
+	 * SysClkReq5Valid2         = disabled
+	 * SysClkReq6Valid2         = SysClkReq6 controlled
+	 * SysClkReq7Valid2         = disabled
+	 * SysClkReq8Valid2         = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUSYSCLKREQVALID2, 0x20),
+	/*
+	 * VTVoutEna                = disabled
+	 * Vintcore12Ena            = disabled
+	 * Vintcore12Sel            = 1.25 V
+	 * Vintcore12LP             = inactive (HP)
+	 * VTVoutLP                 = inactive (HP)
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUMISC1, 0x10),
+	/*
+	 * VaudioEna                = disabled
+	 * VdmicEna                 = disabled
+	 * Vamic1Ena                = disabled
+	 * Vamic2Ena                = disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VAUDIOSUPPLY, 0x00),
+	/*
+	 * Vamic1_dzout             = high-Z when Vamic1 is disabled
+	 * Vamic2_dzout             = high-Z when Vamic2 is disabled
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUCTRL1VAMIC, 0x00),
+	/*
+	 * VPll                     = Hw controlled
+	 * VanaRegu                 = force off
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VPLLVANAREGU, 0x02),
+	/*
+	 * VrefDDREna               = disabled
+	 * VrefDDRSleepMode         = inactive (no pulldown)
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VREFDDR, 0x00),
+	/*
+	 * VextSupply1Regu          = HW control
+	 * VextSupply2Regu          = HW control
+	 * VextSupply3Regu          = HW control
+	 * ExtSupply2Bypass         = ExtSupply12LPn ball is 0 when Ena is 0
+	 * ExtSupply3Bypass         = ExtSupply3LPn ball is 0 when Ena is 0
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_EXTSUPPLYREGU, 0x2a),
+	/*
+	 * Vaux1Regu                = force HP
+	 * Vaux2Regu                = force off
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VAUX12REGU, 0x01),
+	/*
+	 * Vaux3regu                = force off
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VRF1VAUX3REGU, 0x00),
+	/*
+	 * Vsmps1                   = 1.15V
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VSMPS1SEL1, 0x24),
+	/*
+	 * Vaux1Sel                 = 2.5 V
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VAUX1SEL, 0x08),
+	/*
+	 * Vaux2Sel                 = 2.9 V
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VAUX2SEL, 0x0d),
+	/*
+	 * Vaux3Sel                 = 2.91 V
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_VRF1VAUX3SEL, 0x07),
+	/*
+	 * VextSupply12LP           = disabled (no LP)
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUCTRL2SPARE, 0x00),
+	/*
+	 * Vaux1Disch               = short discharge time
+	 * Vaux2Disch               = short discharge time
+	 * Vaux3Disch               = short discharge time
+	 * Vintcore12Disch          = short discharge time
+	 * VTVoutDisch              = short discharge time
+	 * VaudioDisch              = short discharge time
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUCTRLDISCH, 0x00),
+	/*
+	 * VanaDisch                = short discharge time
+	 * VdmicPullDownEna         = pulldown disabled when Vdmic is disabled
+	 * VdmicDisch               = short discharge time
+	 */
+	INIT_REGULATOR_REGISTER(AB8500_REGUCTRLDISCH2, 0x00),
+};
+
 /* AB8500 regulators */
 struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = {
 	/* supplies to the display/camera */
@@ -72,6 +272,7 @@ struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS] = {
 			.max_uV = 2900000,
 			.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
 					  REGULATOR_CHANGE_STATUS,
+			.boot_on = 1, /* must be on for display */
 		},
 		.num_consumer_supplies = ARRAY_SIZE(ab8500_vaux1_consumers),
 		.consumer_supplies = ab8500_vaux1_consumers,

arch/arm/mach-ux500/board-mop500-regulators.h

@@ -17,5 +17,6 @@
 extern struct ab8500_regulator_reg_init
 ab8500_regulator_reg_init[AB8500_NUM_REGULATOR_REGISTERS];
 extern struct regulator_init_data ab8500_regulators[AB8500_NUM_REGULATORS];
+extern struct regulator_init_data tps61052_regulator;
 
 #endif

arch/arm/mach-ux500/board-mop500.c

@@ -22,6 +22,8 @@
 #include <linux/mfd/ab8500.h>
 #include <linux/regulator/ab8500.h>
 #include <linux/mfd/tc3589x.h>
+#include <linux/mfd/tps6105x.h>
+#include <linux/mfd/ab8500/gpio.h>
 #include <linux/leds-lp5521.h>
 #include <linux/input.h>
 #include <linux/gpio_keys.h>
@@ -42,10 +44,35 @@
 #include "board-mop500.h"
 #include "board-mop500-regulators.h"
 
+static struct ab8500_gpio_platform_data ab8500_gpio_pdata = {
+	.gpio_base		= MOP500_AB8500_GPIO(0),
+	.irq_base		= MOP500_AB8500_VIR_GPIO_IRQ_BASE,
+	/* config_reg is the initial configuration of ab8500 pins.
+	 * The pins can be configured as GPIO or alt functions based
+	 * on value present in GpioSel1 to GpioSel6 and AlternatFunction
+	 * register. This is the array of 7 configuration settings.
+	 * One has to compile time decide these settings. Below is the
+	 * explaination of these setting
+	 * GpioSel1 = 0x00 => Pins GPIO1 to GPIO8 are not used as GPIO
+	 * GpioSel2 = 0x1E => Pins GPIO10 to GPIO13 are configured as GPIO
+	 * GpioSel3 = 0x80 => Pin GPIO24 is configured as GPIO
+	 * GpioSel4 = 0x01 => Pin GPIo25 is configured as GPIO
+	 * GpioSel5 = 0x7A => Pins GPIO34, GPIO36 to GPIO39 are conf as GPIO
+	 * GpioSel6 = 0x00 => Pins GPIO41 & GPIo42 are not configured as GPIO
+	 * AlternaFunction = 0x00 => If Pins GPIO10 to 13 are not configured
+	 * as GPIO then this register selectes the alternate fucntions
+	 */
+	.config_reg		= {0x00, 0x1E, 0x80, 0x01,
+					0x7A, 0x00, 0x00},
+};
+
 static struct ab8500_platform_data ab8500_platdata = {
 	.irq_base	= MOP500_AB8500_IRQ_BASE,
+	.regulator_reg_init = ab8500_regulator_reg_init,
+	.num_regulator_reg_init	= ARRAY_SIZE(ab8500_regulator_reg_init),
 	.regulator	= ab8500_regulators,
 	.num_regulator	= ARRAY_SIZE(ab8500_regulators),
+	.gpio		= &ab8500_gpio_pdata,
 };
 
 static struct resource ab8500_resources[] = {
@@ -66,6 +93,15 @@ struct platform_device ab8500_device = {
 	.resource = ab8500_resources,
 };
 
+/*
+ * TPS61052
+ */
+
+static struct tps6105x_platform_data mop500_tps61052_data = {
+	.mode = TPS6105X_MODE_VOLTAGE,
+	.regulator_data = &tps61052_regulator,
+};
+
 /*
  * TC35892
  */
@@ -136,7 +172,7 @@ static struct lp5521_platform_data __initdata lp5521_sec_data = {
        .clock_mode     = LP5521_CLOCK_EXT,
 };
 
-static struct i2c_board_info mop500_i2c0_devices[] = {
+static struct i2c_board_info __initdata mop500_i2c0_devices[] = {
 	{
 		I2C_BOARD_INFO("tc3589x", 0x42),
 		.irq		= NOMADIK_GPIO_TO_IRQ(217),
@@ -144,6 +180,14 @@ static struct i2c_board_info mop500_i2c0_devices[] = {
 	},
 };
 
+/* I2C0 devices only available prior to HREFv60 */
+static struct i2c_board_info __initdata mop500_i2c0_old_devices[] = {
+	{
+		I2C_BOARD_INFO("tps61052", 0x33),
+		.platform_data  = &mop500_tps61052_data,
+	},
+};
+
 static struct i2c_board_info __initdata mop500_i2c2_devices[] = {
 	{
 		/* lp5521 LED driver, 1st device */
@@ -406,6 +450,9 @@ static void __init mop500_init_machine(void)
 
 	i2c_register_board_info(0, mop500_i2c0_devices,
 				ARRAY_SIZE(mop500_i2c0_devices));
+	if (!machine_is_hrefv60())
+		i2c_register_board_info(0, mop500_i2c0_old_devices,
+					ARRAY_SIZE(mop500_i2c0_old_devices));
 	i2c_register_board_info(2, mop500_i2c2_devices,
 				ARRAY_SIZE(mop500_i2c2_devices));
 }

arch/arm/mach-ux500/board-mop500.h

@@ -27,6 +27,10 @@
 #define GPIO_BU21013_CS			MOP500_EGPIO(13)
 #define GPIO_SDMMC_EN			MOP500_EGPIO(17)
 #define GPIO_SDMMC_1V8_3V_SEL		MOP500_EGPIO(18)
+#define MOP500_EGPIO_END		MOP500_EGPIO(24)
+
+/* GPIOs on the AB8500 mixed-signals circuit */
+#define MOP500_AB8500_GPIO(x)		(MOP500_EGPIO_END + (x))
 
 struct i2c_board_info;
 

arch/arm/mach-ux500/include/mach/irqs-board-mop500.h

@@ -35,9 +35,20 @@
 #define MOP500_STMPE1601_IRQBASE        MOP500_EGPIO_IRQ_END
 #define MOP500_STMPE1601_IRQ(x)         (MOP500_STMPE1601_IRQBASE + (x))
 
-#define MOP500_NR_IRQS          MOP500_STMPE1601_IRQ(STMPE_NR_INTERNAL_IRQS)
+#define MOP500_STMPE1601_IRQ_END	\
+	MOP500_STMPE1601_IRQ(STMPE_NR_INTERNAL_IRQS)
 
-#define MOP500_IRQ_END          MOP500_NR_IRQS
+/* AB8500 virtual gpio IRQ */
+#define AB8500_VIR_GPIO_NR_IRQS			16
+
+#define MOP500_AB8500_VIR_GPIO_IRQ_BASE		\
+	MOP500_STMPE1601_IRQ_END
+#define MOP500_AB8500_VIR_GPIO_IRQ_END		\
+	(MOP500_AB8500_VIR_GPIO_IRQ_BASE + AB8500_VIR_GPIO_NR_IRQS)
+
+#define MOP500_NR_IRQS		MOP500_AB8500_VIR_GPIO_IRQ_END
+
+#define MOP500_IRQ_END		MOP500_NR_IRQS
 
 #if MOP500_IRQ_END > IRQ_BOARD_END
 #undef IRQ_BOARD_END

drivers/gpio/Kconfig

@@ -414,4 +414,9 @@ config GPIO_JANZ_TTL
 	  This driver provides support for driving the pins in output
 	  mode only. Input mode is not supported.
 
+config AB8500_GPIO
+	bool "ST-Ericsson AB8500 Mixed Signal Circuit gpio functions"
+	depends on AB8500_CORE
+	help
+	  Select this to enable the AB8500 IC GPIO driver
 endif

drivers/gpio/Makefile

@@ -42,3 +42,4 @@ obj-$(CONFIG_GPIO_JANZ_TTL)	+= janz-ttl.o
 obj-$(CONFIG_GPIO_SX150X)	+= sx150x.o
 obj-$(CONFIG_GPIO_VX855)	+= vx855_gpio.o
 obj-$(CONFIG_GPIO_ML_IOH)	+= ml_ioh_gpio.o
+obj-$(CONFIG_AB8500_GPIO)       += ab8500-gpio.o

drivers/gpio/ab8500-gpio.c

@@ -0,0 +1,522 @@
+/*
+ * Copyright (C) ST-Ericsson SA 2011
+ *
+ * Author: BIBEK BASU <bibek.basu@stericsson.com>
+ * License terms: GNU General Public License (GPL) version 2
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/gpio.h>
+#include <linux/irq.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/ab8500.h>
+#include <linux/mfd/abx500.h>
+#include <linux/mfd/ab8500/gpio.h>
+
+/*
+ * GPIO registers offset
+ * Bank: 0x10
+ */
+#define AB8500_GPIO_SEL1_REG	0x00
+#define AB8500_GPIO_SEL2_REG	0x01
+#define AB8500_GPIO_SEL3_REG	0x02
+#define AB8500_GPIO_SEL4_REG	0x03
+#define AB8500_GPIO_SEL5_REG	0x04
+#define AB8500_GPIO_SEL6_REG	0x05
+
+#define AB8500_GPIO_DIR1_REG	0x10
+#define AB8500_GPIO_DIR2_REG	0x11
+#define AB8500_GPIO_DIR3_REG	0x12
+#define AB8500_GPIO_DIR4_REG	0x13
+#define AB8500_GPIO_DIR5_REG	0x14
+#define AB8500_GPIO_DIR6_REG	0x15
+
+#define AB8500_GPIO_OUT1_REG	0x20
+#define AB8500_GPIO_OUT2_REG	0x21
+#define AB8500_GPIO_OUT3_REG	0x22
+#define AB8500_GPIO_OUT4_REG	0x23
+#define AB8500_GPIO_OUT5_REG	0x24
+#define AB8500_GPIO_OUT6_REG	0x25
+
+#define AB8500_GPIO_PUD1_REG	0x30
+#define AB8500_GPIO_PUD2_REG	0x31
+#define AB8500_GPIO_PUD3_REG	0x32
+#define AB8500_GPIO_PUD4_REG	0x33
+#define AB8500_GPIO_PUD5_REG	0x34
+#define AB8500_GPIO_PUD6_REG	0x35
+
+#define AB8500_GPIO_IN1_REG	0x40
+#define AB8500_GPIO_IN2_REG	0x41
+#define AB8500_GPIO_IN3_REG	0x42
+#define AB8500_GPIO_IN4_REG	0x43
+#define AB8500_GPIO_IN5_REG	0x44
+#define AB8500_GPIO_IN6_REG	0x45
+#define AB8500_GPIO_ALTFUN_REG	0x45
+#define ALTFUN_REG_INDEX	6
+#define AB8500_NUM_GPIO		42
+#define AB8500_NUM_VIR_GPIO_IRQ	16
+
+enum ab8500_gpio_action {
+	NONE,
+	STARTUP,
+	SHUTDOWN,
+	MASK,
+	UNMASK
+};
+
+struct ab8500_gpio {
+	struct gpio_chip chip;
+	struct ab8500 *parent;
+	struct device *dev;
+	struct mutex lock;
+	u32 irq_base;
+	enum ab8500_gpio_action irq_action;
+	u16 rising;
+	u16 falling;
+};
+/**
+ * to_ab8500_gpio() - get the pointer to ab8500_gpio
+ * @chip:	Member of the structure ab8500_gpio
+ */
+static inline struct ab8500_gpio *to_ab8500_gpio(struct gpio_chip *chip)
+{
+	return container_of(chip, struct ab8500_gpio, chip);
+}
+
+static int ab8500_gpio_set_bits(struct gpio_chip *chip, u8 reg,
+					unsigned offset, int val)
+{
+	struct ab8500_gpio *ab8500_gpio = to_ab8500_gpio(chip);
+	u8 pos = offset % 8;
+	int ret;
+
+	reg = reg + (offset / 8);
+	ret = abx500_mask_and_set_register_interruptible(ab8500_gpio->dev,
+				AB8500_MISC, reg, 1 << pos, val << pos);
+	if (ret < 0)
+		dev_err(ab8500_gpio->dev, "%s write failed\n", __func__);
+	return ret;
+}
+/**
+ * ab8500_gpio_get() - Get the particular GPIO value
+ * @chip: Gpio device
+ * @offset: GPIO number to read
+ */
+static int ab8500_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+	struct ab8500_gpio *ab8500_gpio = to_ab8500_gpio(chip);
+	u8 mask = 1 << (offset % 8);
+	u8 reg = AB8500_GPIO_OUT1_REG + (offset / 8);
+	int ret;
+	u8 data;
+	ret = abx500_get_register_interruptible(ab8500_gpio->dev, AB8500_MISC,
+						reg, &data);
+	if (ret < 0) {
+		dev_err(ab8500_gpio->dev, "%s read failed\n", __func__);
+		return ret;
+	}
+	return (data & mask) >> (offset % 8);
+}
+
+static void ab8500_gpio_set(struct gpio_chip *chip, unsigned offset, int val)
+{
+	struct ab8500_gpio *ab8500_gpio = to_ab8500_gpio(chip);
+	int ret;
+	/* Write the data */
+	ret = ab8500_gpio_set_bits(chip, AB8500_GPIO_OUT1_REG, offset, 1);
+	if (ret < 0)
+		dev_err(ab8500_gpio->dev, "%s write failed\n", __func__);
+}
+
+static int ab8500_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
+					int val)
+{
+	int ret;
+	/* set direction as output */
+	ret = ab8500_gpio_set_bits(chip, AB8500_GPIO_DIR1_REG, offset, 1);
+	if (ret < 0)
+		return ret;
+	/* disable pull down */
+	ret = ab8500_gpio_set_bits(chip, AB8500_GPIO_PUD1_REG, offset, 1);
+	if (ret < 0)
+		return ret;
+	/* set the output as 1 or 0 */
+	return ab8500_gpio_set_bits(chip, AB8500_GPIO_OUT1_REG, offset, val);
+
+}
+
+static int ab8500_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	/* set the register as input */
+	return ab8500_gpio_set_bits(chip, AB8500_GPIO_DIR1_REG, offset, 0);
+}
+
+static int ab8500_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+	/*
+	 * Only some GPIOs are interrupt capable, and they are
+	 * organized in discontiguous clusters:
+	 *
+	 *	GPIO6 to GPIO13
+	 *	GPIO24 and GPIO25
+	 *	GPIO36 to GPIO41
+	 */
+	static struct ab8500_gpio_irq_cluster {
+		int start;
+		int end;
+	} clusters[] = {
+		{.start = 6,  .end = 13},
+		{.start = 24, .end = 25},
+		{.start = 36, .end = 41},
+	};
+	struct ab8500_gpio *ab8500_gpio = to_ab8500_gpio(chip);
+	int base = ab8500_gpio->irq_base;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(clusters); i++) {
+		struct ab8500_gpio_irq_cluster *cluster = &clusters[i];
+
+		if (offset >= cluster->start && offset <= cluster->end)
+			return base + offset - cluster->start;
+
+		/* Advance by the number of gpios in this cluster */
+		base += cluster->end - cluster->start + 1;
+	}
+
+	return -EINVAL;
+}
+
+static struct gpio_chip ab8500gpio_chip = {
+	.label			= "ab8500_gpio",
+	.owner			= THIS_MODULE,
+	.direction_input	= ab8500_gpio_direction_input,
+	.get			= ab8500_gpio_get,
+	.direction_output	= ab8500_gpio_direction_output,
+	.set			= ab8500_gpio_set,
+	.to_irq			= ab8500_gpio_to_irq,
+};
+
+static unsigned int irq_to_rising(unsigned int irq)
+{
+	struct ab8500_gpio *ab8500_gpio = get_irq_chip_data(irq);
+	int offset = irq - ab8500_gpio->irq_base;
+	int new_irq = offset +  AB8500_INT_GPIO6R
+			+ ab8500_gpio->parent->irq_base;
+	return new_irq;
+}
+
+static unsigned int irq_to_falling(unsigned int irq)
+{
+	struct ab8500_gpio *ab8500_gpio = get_irq_chip_data(irq);
+	int offset = irq - ab8500_gpio->irq_base;
+	int new_irq = offset +  AB8500_INT_GPIO6F
+			+  ab8500_gpio->parent->irq_base;
+	return new_irq;
+
+}
+
+static unsigned int rising_to_irq(unsigned int irq, void *dev)
+{
+	struct ab8500_gpio *ab8500_gpio = dev;
+	int offset = irq - AB8500_INT_GPIO6R
+			- ab8500_gpio->parent->irq_base ;
+	int new_irq = offset + ab8500_gpio->irq_base;
+	return new_irq;
+}
+
+static unsigned int falling_to_irq(unsigned int irq, void *dev)
+{
+	struct ab8500_gpio *ab8500_gpio = dev;
+	int offset = irq - AB8500_INT_GPIO6F
+			- ab8500_gpio->parent->irq_base ;
+	int new_irq = offset + ab8500_gpio->irq_base;
+	return new_irq;
+
+}
+
+/*
+ * IRQ handler
+ */
+
+static irqreturn_t handle_rising(int irq, void *dev)
+{
+
+	handle_nested_irq(rising_to_irq(irq , dev));
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t handle_falling(int irq, void *dev)
+{
+
+	handle_nested_irq(falling_to_irq(irq, dev));
+	return IRQ_HANDLED;
+}
+
+static void ab8500_gpio_irq_lock(unsigned int irq)
+{
+	struct ab8500_gpio *ab8500_gpio = get_irq_chip_data(irq);
+	mutex_lock(&ab8500_gpio->lock);
+}
+
+static void ab8500_gpio_irq_sync_unlock(unsigned int irq)
+{
+	struct ab8500_gpio *ab8500_gpio = get_irq_chip_data(irq);
+	int offset = irq - ab8500_gpio->irq_base;
+	bool rising = ab8500_gpio->rising & BIT(offset);
+	bool falling = ab8500_gpio->falling & BIT(offset);
+	int ret;
+
+	switch (ab8500_gpio->irq_action)	{
+	case STARTUP:
+		if (rising)
+			ret = request_threaded_irq(irq_to_rising(irq),
+					NULL, handle_rising,
+					IRQF_TRIGGER_RISING,
+					"ab8500-gpio-r", ab8500_gpio);
+		if (falling)
+			ret = request_threaded_irq(irq_to_falling(irq),
+				       NULL, handle_falling,
+				       IRQF_TRIGGER_FALLING,
+				       "ab8500-gpio-f", ab8500_gpio);
+		break;
+	case SHUTDOWN:
+		if (rising)
+			free_irq(irq_to_rising(irq), ab8500_gpio);
+		if (falling)
+			free_irq(irq_to_falling(irq), ab8500_gpio);
+		break;
+	case MASK:
+		if (rising)
+			disable_irq(irq_to_rising(irq));
+		if (falling)
+			disable_irq(irq_to_falling(irq));
+		break;
+	case UNMASK:
+		if (rising)
+			enable_irq(irq_to_rising(irq));
+		if (falling)
+			enable_irq(irq_to_falling(irq));
+		break;
+	case NONE:
+		break;
+	}
+	ab8500_gpio->irq_action = NONE;
+	ab8500_gpio->rising &= ~(BIT(offset));
+	ab8500_gpio->falling &= ~(BIT(offset));
+	mutex_unlock(&ab8500_gpio->lock);
+}
+
+
+static void ab8500_gpio_irq_mask(unsigned int irq)
+{
+	struct ab8500_gpio *ab8500_gpio = get_irq_chip_data(irq);
+	ab8500_gpio->irq_action = MASK;
+}
+
+static void ab8500_gpio_irq_unmask(unsigned int irq)
+{
+	struct ab8500_gpio *ab8500_gpio = get_irq_chip_data(irq);
+	ab8500_gpio->irq_action = UNMASK;
+}
+
+static int ab8500_gpio_irq_set_type(unsigned int irq, unsigned int type)
+{
+	struct ab8500_gpio *ab8500_gpio = get_irq_chip_data(irq);
+	int offset = irq - ab8500_gpio->irq_base;
+
+	if (type == IRQ_TYPE_EDGE_BOTH) {
+		ab8500_gpio->rising =  BIT(offset);
+		ab8500_gpio->falling = BIT(offset);
+	} else if (type == IRQ_TYPE_EDGE_RISING) {
+		ab8500_gpio->rising =  BIT(offset);
+	} else  {
+		ab8500_gpio->falling = BIT(offset);
+	}
+	return 0;
+}
+
+unsigned int ab8500_gpio_irq_startup(unsigned int irq)
+{
+	struct ab8500_gpio *ab8500_gpio = get_irq_chip_data(irq);
+	ab8500_gpio->irq_action = STARTUP;
+	return 0;
+}
+
+void ab8500_gpio_irq_shutdown(unsigned int irq)
+{
+	struct ab8500_gpio *ab8500_gpio = get_irq_chip_data(irq);
+	ab8500_gpio->irq_action = SHUTDOWN;
+}
+
+static struct irq_chip ab8500_gpio_irq_chip = {
+	.name			= "ab8500-gpio",
+	.startup		= ab8500_gpio_irq_startup,
+	.shutdown		= ab8500_gpio_irq_shutdown,
+	.bus_lock		= ab8500_gpio_irq_lock,
+	.bus_sync_unlock	= ab8500_gpio_irq_sync_unlock,
+	.mask			= ab8500_gpio_irq_mask,
+	.unmask			= ab8500_gpio_irq_unmask,
+	.set_type		= ab8500_gpio_irq_set_type,
+};
+
+static int ab8500_gpio_irq_init(struct ab8500_gpio *ab8500_gpio)
+{
+	u32 base = ab8500_gpio->irq_base;
+	int irq;
+
+	for (irq = base; irq < base + AB8500_NUM_VIR_GPIO_IRQ ; irq++) {
+		set_irq_chip_data(irq, ab8500_gpio);
+		set_irq_chip_and_handler(irq, &ab8500_gpio_irq_chip,
+				handle_simple_irq);
+		set_irq_nested_thread(irq, 1);
+#ifdef CONFIG_ARM
+		set_irq_flags(irq, IRQF_VALID);
+#else
+		set_irq_noprobe(irq);
+#endif
+	}
+
+	return 0;
+}
+
+static void ab8500_gpio_irq_remove(struct ab8500_gpio *ab8500_gpio)
+{
+	int base = ab8500_gpio->irq_base;
+	int irq;
+
+	for (irq = base; irq < base + AB8500_NUM_VIR_GPIO_IRQ; irq++) {
+#ifdef CONFIG_ARM
+		set_irq_flags(irq, 0);
+#endif
+		set_irq_chip_and_handler(irq, NULL, NULL);
+		set_irq_chip_data(irq, NULL);
+	}
+}
+
+static int __devinit ab8500_gpio_probe(struct platform_device *pdev)
+{
+	struct ab8500_platform_data *ab8500_pdata =
+				dev_get_platdata(pdev->dev.parent);
+	struct ab8500_gpio_platform_data *pdata;
+	struct ab8500_gpio *ab8500_gpio;
+	int ret;
+	int i;
+
+	pdata = ab8500_pdata->gpio;
+	if (!pdata)	{
+		dev_err(&pdev->dev, "gpio platform data missing\n");
+		return -ENODEV;
+	}
+
+	ab8500_gpio = kzalloc(sizeof(struct ab8500_gpio), GFP_KERNEL);
+	if (ab8500_gpio == NULL) {
+		dev_err(&pdev->dev, "failed to allocate memory\n");
+		return -ENOMEM;
+	}
+	ab8500_gpio->dev = &pdev->dev;
+	ab8500_gpio->parent = dev_get_drvdata(pdev->dev.parent);
+	ab8500_gpio->chip = ab8500gpio_chip;
+	ab8500_gpio->chip.ngpio = AB8500_NUM_GPIO;
+	ab8500_gpio->chip.dev = &pdev->dev;
+	ab8500_gpio->chip.base = pdata->gpio_base;
+	ab8500_gpio->irq_base = pdata->irq_base;
+	/* initialize the lock */
+	mutex_init(&ab8500_gpio->lock);
+	/*
+	 * AB8500 core will handle and clear the IRQ
+	 * configre GPIO based on config-reg value.
+	 * These values are for selecting the PINs as
+	 * GPIO or alternate function
+	 */
+	for (i = AB8500_GPIO_SEL1_REG; i <= AB8500_GPIO_SEL6_REG; i++)	{
+		ret = abx500_set_register_interruptible(ab8500_gpio->dev,
+				AB8500_MISC, i,
+				pdata->config_reg[i]);
+		if (ret < 0)
+			goto out_free;
+	}
+	ret = abx500_set_register_interruptible(ab8500_gpio->dev, AB8500_MISC,
+				AB8500_GPIO_ALTFUN_REG,
+				pdata->config_reg[ALTFUN_REG_INDEX]);
+	if (ret < 0)
+		goto out_free;
+
+	ret = ab8500_gpio_irq_init(ab8500_gpio);
+	if (ret)
+		goto out_free;
+	ret = gpiochip_add(&ab8500_gpio->chip);
+	if (ret) {
+		dev_err(&pdev->dev, "unable to add gpiochip: %d\n",
+				ret);
+		goto out_rem_irq;
+	}
+	platform_set_drvdata(pdev, ab8500_gpio);
+	return 0;
+
+out_rem_irq:
+	ab8500_gpio_irq_remove(ab8500_gpio);
+out_free:
+	mutex_destroy(&ab8500_gpio->lock);
+	kfree(ab8500_gpio);
+	return ret;
+}
+
+/*
+ * ab8500_gpio_remove() - remove Ab8500-gpio driver
+ * @pdev :	Platform device registered
+ */
+static int __devexit ab8500_gpio_remove(struct platform_device *pdev)
+{
+	struct ab8500_gpio *ab8500_gpio = platform_get_drvdata(pdev);
+	int ret;
+
+	ret = gpiochip_remove(&ab8500_gpio->chip);
+	if (ret < 0) {
+		dev_err(ab8500_gpio->dev, "unable to remove gpiochip:\
+				%d\n", ret);
+		return ret;
+	}
+
+	platform_set_drvdata(pdev, NULL);
+	mutex_destroy(&ab8500_gpio->lock);
+	kfree(ab8500_gpio);
+
+	return 0;
+}
+
+static struct platform_driver ab8500_gpio_driver = {
+	.driver = {
+		.name = "ab8500-gpio",
+		.owner = THIS_MODULE,
+	},
+	.probe = ab8500_gpio_probe,
+	.remove = __devexit_p(ab8500_gpio_remove),
+};
+
+static int __init ab8500_gpio_init(void)
+{
+	return platform_driver_register(&ab8500_gpio_driver);
+}
+arch_initcall(ab8500_gpio_init);
+
+static void __exit ab8500_gpio_exit(void)
+{
+	platform_driver_unregister(&ab8500_gpio_driver);
+}
+module_exit(ab8500_gpio_exit);
+
+MODULE_AUTHOR("BIBEK BASU <bibek.basu@stericsson.com>");
+MODULE_DESCRIPTION("Driver allows to use AB8500 unused pins\
+			to be used as GPIO");
+MODULE_ALIAS("AB8500 GPIO driver");
+MODULE_LICENSE("GPL v2");

drivers/mfd/ab8500-core.c

@@ -362,6 +362,15 @@ static void ab8500_irq_remove(struct ab8500 *ab8500)
 	}
 }
 
+static struct resource ab8500_gpio_resources[] = {
+	{
+		.name	= "GPIO_INT6",
+		.start	= AB8500_INT_GPIO6R,
+		.end	= AB8500_INT_GPIO41F,
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
 static struct resource ab8500_gpadc_resources[] = {
 	{
 		.name	= "HW_CONV_END",
@@ -595,6 +604,11 @@ static struct mfd_cell ab8500_devs[] = {
 	{
 		.name = "ab8500-regulator",
 	},
+	{
+		.name = "ab8500-gpio",
+		.num_resources = ARRAY_SIZE(ab8500_gpio_resources),
+		.resources = ab8500_gpio_resources,
+	},
 	{
 		.name = "ab8500-gpadc",
 		.num_resources = ARRAY_SIZE(ab8500_gpadc_resources),

drivers/mfd/ab8500-i2c.c

@@ -97,7 +97,7 @@ static void __exit ab8500_i2c_exit(void)
 {
 	platform_driver_unregister(&ab8500_i2c_driver);
 }
-subsys_initcall(ab8500_i2c_init);
+arch_initcall(ab8500_i2c_init);
 module_exit(ab8500_i2c_exit);
 
 MODULE_AUTHOR("Mattias WALLIN <mattias.wallin@stericsson.com");

include/linux/mfd/ab8500.h

@@ -74,6 +74,45 @@
 #define AB8500_INT_ACC_DETECT_21DB_F	37
 #define AB8500_INT_ACC_DETECT_21DB_R	38
 #define AB8500_INT_GP_SW_ADC_CONV_END	39
+#define AB8500_INT_ACC_DETECT_1DB_F	33
+#define AB8500_INT_ACC_DETECT_1DB_R	34
+#define AB8500_INT_ACC_DETECT_22DB_F	35
+#define AB8500_INT_ACC_DETECT_22DB_R	36
+#define AB8500_INT_ACC_DETECT_21DB_F	37
+#define AB8500_INT_ACC_DETECT_21DB_R	38
+#define AB8500_INT_GP_SW_ADC_CONV_END	39
+#define AB8500_INT_GPIO6R		40
+#define AB8500_INT_GPIO7R		41
+#define AB8500_INT_GPIO8R		42
+#define AB8500_INT_GPIO9R		43
+#define AB8500_INT_GPIO10R		44
+#define AB8500_INT_GPIO11R		45
+#define AB8500_INT_GPIO12R		46
+#define AB8500_INT_GPIO13R		47
+#define AB8500_INT_GPIO24R		48
+#define AB8500_INT_GPIO25R		49
+#define AB8500_INT_GPIO36R		50
+#define AB8500_INT_GPIO37R		51
+#define AB8500_INT_GPIO38R		52
+#define AB8500_INT_GPIO39R		53
+#define AB8500_INT_GPIO40R		54
+#define AB8500_INT_GPIO41R		55
+#define AB8500_INT_GPIO6F		56
+#define AB8500_INT_GPIO7F		57
+#define AB8500_INT_GPIO8F		58
+#define AB8500_INT_GPIO9F		59
+#define AB8500_INT_GPIO10F		60
+#define AB8500_INT_GPIO11F		61
+#define AB8500_INT_GPIO12F		62
+#define AB8500_INT_GPIO13F		63
+#define AB8500_INT_GPIO24F		64
+#define AB8500_INT_GPIO25F		65
+#define AB8500_INT_GPIO36F		66
+#define AB8500_INT_GPIO37F		67
+#define AB8500_INT_GPIO38F		68
+#define AB8500_INT_GPIO39F		69
+#define AB8500_INT_GPIO40F		70
+#define AB8500_INT_GPIO41F		71
 #define AB8500_INT_ADP_SOURCE_ERROR	72
 #define AB8500_INT_ADP_SINK_ERROR	73
 #define AB8500_INT_ADP_PROBE_PLUG	74
@@ -141,6 +180,7 @@ struct ab8500 {
 
 struct regulator_reg_init;
 struct regulator_init_data;
+struct ab8500_gpio_platform_data;
 
 /**
  * struct ab8500_platform_data - AB8500 platform data
@@ -158,6 +198,7 @@ struct ab8500_platform_data {
 	struct ab8500_regulator_reg_init *regulator_reg_init;
 	int num_regulator;
 	struct regulator_init_data *regulator;
+	struct ab8500_gpio_platform_data *gpio;
 };
 
 extern int __devinit ab8500_init(struct ab8500 *ab8500);

include/linux/mfd/ab8500/gpio.h

@@ -0,0 +1,21 @@
+/*
+ * Copyright ST-Ericsson 2010.
+ *
+ * Author: Bibek Basu <bibek.basu@stericsson.com>
+ * Licensed under GPLv2.
+ */
+
+#ifndef _AB8500_GPIO_H
+#define _AB8500_GPIO_H
+
+/*
+ * Platform data to register a block: only the initial gpio/irq number.
+ */
+
+struct ab8500_gpio_platform_data {
+	int gpio_base;
+	u32 irq_base;
+	u8  config_reg[7];
+};
+
+#endif /* _AB8500_GPIO_H */