Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Resolve conflict between commit 264640fc2c5f4f ("ipv6: distinguish frag
queues by device for multicast and link-local packets") from the net
tree and commit 029f7f3b8701c ("netfilter: ipv6: nf_defrag: avoid/free
clone operations") from the nf-next tree.

Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Conflicts:
	net/ipv6/netfilter/nf_conntrack_reasm.c

Documentation/ABI/testing/sysfs-class-net-cdc_ncm

@@ -19,6 +19,25 @@ Description:
 		Set to 0 to pad all frames. Set greater than tx_max to
 		disable all padding.
 
+What:		/sys/class/net/<iface>/cdc_ncm/ndp_to_end
+Date:		Dec 2015
+KernelVersion:	4.5
+Contact:	Bjørn Mork <bjorn@mork.no>
+Description:
+		Boolean attribute showing the status of the "NDP to
+		end" quirk.  Defaults to 'N', except for devices
+		already known to need it enabled.
+
+		The "NDP to end" quirk makes the driver place the NDP
+		(the packet index table) after the payload.  The NCM
+		specification does not mandate this, but some devices
+		are known to be more restrictive. Write 'Y' to this
+		attribute for temporary testing of a suspect device
+		failing to work with the default driver settings.
+
+		A device entry should be added to the driver if this
+		quirk is found to be required.
+
 What:		/sys/class/net/<iface>/cdc_ncm/rx_max
 Date:		May 2014
 KernelVersion:	3.16

Documentation/ABI/testing/sysfs-class-net-qmi

@@ -0,0 +1,23 @@
+What:		/sys/class/net/<iface>/qmi/raw_ip
+Date:		Dec 2015
+KernelVersion:	4.4
+Contact:	Bjørn Mork <bjorn@mork.no>
+Description:
+		Boolean.  Default: 'N'
+
+		Set this to 'Y' to change the network device link
+		framing from '802.3' to 'raw-ip'.
+
+		The netdev will change to reflect the link framing
+		mode.  The netdev is an ordinary ethernet device in
+		'802.3' mode, and the driver expects to exchange
+		frames with an ethernet header over the USB link. The
+		netdev is a headerless p-t-p device in 'raw-ip' mode,
+		and the driver expects to echange IPv4 or IPv6 packets
+		without any L2 header over the USB link.
+
+		Userspace is in full control of firmware configuration
+		through the delegation of the QMI protocol. Userspace
+		is responsible for coordination of driver and firmware
+		link framing mode, changing this setting to 'Y' if the
+		firmware is configured for 'raw-ip' mode.

Documentation/IPMI.txt

@@ -587,7 +587,7 @@ used to control it:
 
   modprobe ipmi_watchdog timeout=<t> pretimeout=<t> action=<action type>
       preaction=<preaction type> preop=<preop type> start_now=x
-      nowayout=x ifnum_to_use=n
+      nowayout=x ifnum_to_use=n panic_wdt_timeout=<t>
 
 ifnum_to_use specifies which interface the watchdog timer should use.
 The default is -1, which means to pick the first one registered.
@@ -597,7 +597,9 @@ is the amount of seconds before the reset that the pre-timeout panic will
 occur (if pretimeout is zero, then pretimeout will not be enabled).  Note
 that the pretimeout is the time before the final timeout.  So if the
 timeout is 50 seconds and the pretimeout is 10 seconds, then the pretimeout
-will occur in 40 second (10 seconds before the timeout).
+will occur in 40 second (10 seconds before the timeout). The panic_wdt_timeout
+is the value of timeout which is set on kernel panic, in order to let actions
+such as kdump to occur during panic.
 
 The action may be "reset", "power_cycle", or "power_off", and
 specifies what to do when the timer times out, and defaults to
@@ -634,6 +636,7 @@ for configuring the watchdog:
 	ipmi_watchdog.preop=<preop type>
 	ipmi_watchdog.start_now=x
 	ipmi_watchdog.nowayout=x
+	ipmi_watchdog.panic_wdt_timeout=<t>
 
 The options are the same as the module parameter options.
 

Documentation/arm/keystone/Overview.txt

@@ -49,24 +49,6 @@ specified through DTS. Following are the DTS used:-
 The device tree documentation for the keystone machines are located at
         Documentation/devicetree/bindings/arm/keystone/keystone.txt
 
-Known issues & workaround
--------------------------
-
-Some of the device drivers used on keystone are re-used from that from
-DaVinci and other TI SoCs. These device drivers may use clock APIs directly.
-Some of the keystone specific drivers such as netcp uses run time power
-management API instead to enable clock. As this API has limitations on
-keystone, following workaround is needed to boot Linux.
-
-   Add 'clk_ignore_unused' to the bootargs env variable in u-boot. Otherwise
-   clock frameworks will try to disable clocks that are unused and disable
-   the hardware. This is because netcp related power domain and clock
-   domains are enabled in u-boot as run time power management API currently
-   doesn't enable clocks for netcp due to a limitation. This workaround is
-   expected to be removed in the future when proper API support becomes
-   available. Until then, this work around is needed.
-
-
 Document Author
 ---------------
 Murali Karicheri <m-karicheri2@ti.com>

Documentation/block/null_blk.txt

@@ -70,3 +70,6 @@ use_per_node_hctx=[0/1]: Default: 0
      parameter.
   1: The multi-queue block layer is instantiated with a hardware dispatch
      queue for each CPU node in the system.
+
+use_lightnvm=[0/1]: Default: 0
+  Register device with LightNVM. Requires blk-mq to be used.

Documentation/devicetree/bindings/net/dsa/dsa.txt

@@ -31,6 +31,8 @@ A switch child node has the following optional property:
 			  switch. Must be set if the switch can not detect
 			  the presence and/or size of a connected EEPROM,
 			  otherwise optional.
+- reset-gpios		: phandle and specifier to a gpio line connected to
+			  reset pin of the switch chip.
 
 A switch may have multiple "port" children nodes
 
@@ -114,6 +116,7 @@ Example:
 			#size-cells = <0>;
 			reg = <17 1>;	/* MDIO address 17, switch 1 in tree */
 			mii-bus = <&mii_bus1>;
+			reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
 
 			switch1port0: port@0 {
 				reg = <0>;

Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt

@@ -8,6 +8,11 @@ Required properties:
 - phy-mode: See ethernet.txt file in the same directory
 - clocks: a pointer to the reference clock for this device.
 
+Optional properties:
+- tx-csum-limit: maximum mtu supported by port that allow TX checksum.
+  Value is presented in bytes. If not used, by default 1600B is set for
+  "marvell,armada-370-neta" and 9800B for others.
+
 Example:
 
 ethernet@d0070000 {
@@ -15,6 +20,7 @@ ethernet@d0070000 {
 	reg = <0xd0070000 0x2500>;
 	interrupts = <8>;
 	clocks = <&gate_clk 4>;
+	tx-csum-limit = <9800>
 	status = "okay";
 	phy = <&phy0>;
 	phy-mode = "rgmii-id";

Documentation/devicetree/bindings/net/micrel-ksz90x1.txt

@@ -1,8 +1,9 @@
 Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY
 
-Some boards require special tuning values, particularly when it comes to
-clock delays. You can specify clock delay values by adding
-micrel-specific properties to an Ethernet OF device node.
+Some boards require special tuning values, particularly when it comes
+to clock delays. You can specify clock delay values in the PHY OF
+device node. Deprecated, but still supported, these properties can
+also be added to an Ethernet OF device node.
 
 Note that these settings are applied after any phy-specific fixup from
 phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c),
@@ -57,16 +58,6 @@ KSZ9031:
 
 Examples:
 
-	/* Attach to an Ethernet device with autodetected PHY */
-	&enet {
-		rxc-skew-ps = <3000>;
-		rxdv-skew-ps = <0>;
-		txc-skew-ps = <3000>;
-		txen-skew-ps = <0>;
-		status = "okay";
-	};
-
-	/* Attach to an explicitly-specified PHY */
 	mdio {
 		phy0: ethernet-phy@0 {
 			rxc-skew-ps = <3000>;

Documentation/devicetree/bindings/net/renesas,ravb.txt

@@ -5,8 +5,18 @@ interface contains.
 
 Required properties:
 - compatible: "renesas,etheravb-r8a7790" if the device is a part of R8A7790 SoC.
+	      "renesas,etheravb-r8a7791" if the device is a part of R8A7791 SoC.
+	      "renesas,etheravb-r8a7792" if the device is a part of R8A7792 SoC.
+	      "renesas,etheravb-r8a7793" if the device is a part of R8A7793 SoC.
 	      "renesas,etheravb-r8a7794" if the device is a part of R8A7794 SoC.
 	      "renesas,etheravb-r8a7795" if the device is a part of R8A7795 SoC.
+	      "renesas,etheravb-rcar-gen2" for generic R-Car Gen 2 compatible interface.
+	      "renesas,etheravb-rcar-gen3" for generic R-Car Gen 3 compatible interface.
+
+	      When compatible with the generic version, nodes must list the
+	      SoC-specific version corresponding to the platform first
+	      followed by the generic version.
+
 - reg: offset and length of (1) the register block and (2) the stream buffer.
 - interrupts: A list of interrupt-specifiers, one for each entry in
 	      interrupt-names.
@@ -37,7 +47,7 @@ Optional properties:
 Example:
 
 	ethernet@e6800000 {
-		compatible = "renesas,etheravb-r8a7795";
+		compatible = "renesas,etheravb-r8a7795", "renesas,etheravb-rcar-gen3";
 		reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>;
 		interrupt-parent = <&gic>;
 		interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,

Documentation/devicetree/bindings/thermal/rockchip-thermal.txt

@@ -1,7 +1,9 @@
 * Temperature Sensor ADC (TSADC) on rockchip SoCs
 
 Required properties:
-- compatible : "rockchip,rk3288-tsadc"
+- compatible : should be "rockchip,<name>-tsadc"
+   "rockchip,rk3288-tsadc": found on RK3288 SoCs
+   "rockchip,rk3368-tsadc": found on RK3368 SoCs
 - reg : physical base address of the controller and length of memory mapped
 	region.
 - interrupts : The interrupt number to the cpu. The interrupt specifier format

Documentation/fault-injection/notifier-error-inject.txt

@@ -10,6 +10,7 @@ modules that can be used to test the following notifiers.
  * PM notifier
  * Memory hotplug notifier
  * powerpc pSeries reconfig notifier
+ * Netdevice notifier
 
 CPU notifier error injection module
 -----------------------------------
@@ -87,6 +88,30 @@ Possible pSeries reconfig notifier events to be failed are:
  * PSERIES_DRCONF_MEM_ADD
  * PSERIES_DRCONF_MEM_REMOVE
 
+Netdevice notifier error injection module
+----------------------------------------------
+This feature is controlled through debugfs interface
+/sys/kernel/debug/notifier-error-inject/netdev/actions/<notifier event>/error
+
+Netdevice notifier events which can be failed are:
+
+ * NETDEV_REGISTER
+ * NETDEV_CHANGEMTU
+ * NETDEV_CHANGENAME
+ * NETDEV_PRE_UP
+ * NETDEV_PRE_TYPE_CHANGE
+ * NETDEV_POST_INIT
+ * NETDEV_PRECHANGEMTU
+ * NETDEV_PRECHANGEUPPER
+ * NETDEV_CHANGEUPPER
+
+Example: Inject netdevice mtu change error (-22 == -EINVAL)
+
+	# cd /sys/kernel/debug/notifier-error-inject/netdev
+	# echo -22 > actions/NETDEV_CHANGEMTU/error
+	# ip link set eth0 mtu 1024
+	RTNETLINK answers: Invalid argument
+
 For more usage examples
 -----------------------
 There are tools/testing/selftests using the notifier error injection features

Documentation/i2c/busses/i2c-i801

@@ -32,6 +32,7 @@ Supported adapters:
   * Intel Sunrise Point-LP (PCH)
   * Intel DNV (SOC)
   * Intel Broxton (SOC)
+  * Intel Lewisburg (PCH)
    Datasheets: Publicly available at the Intel website
 
 On Intel Patsburg and later chipsets, both the normal host SMBus controller

Documentation/kernel-parameters.txt

@@ -1583,9 +1583,6 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 		hwp_only
 			Only load intel_pstate on systems which support
 			hardware P state control (HWP) if available.
-		no_acpi
-			Don't use ACPI processor performance control objects
-			_PSS and _PPC specified limits.
 
 	intremap=	[X86-64, Intel-IOMMU]
 			on	enable Interrupt Remapping (default)

MAINTAINERS

@@ -388,7 +388,7 @@ ADM8211 WIRELESS DRIVER
 L:	linux-wireless@vger.kernel.org
 W:	http://wireless.kernel.org/
 S:	Orphan
-F:	drivers/net/wireless/adm8211.*
+F:	drivers/net/wireless/admtek/adm8211.*
 
 ADP1653 FLASH CONTROLLER DRIVER
 M:	Sakari Ailus <sakari.ailus@iki.fi>
@@ -1847,7 +1847,7 @@ S:	Supported
 F:	drivers/net/wireless/ath/ath6kl/
 
 WILOCITY WIL6210 WIRELESS DRIVER
-M:	Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
+M:	Maya Erez <qca_merez@qca.qualcomm.com>
 L:	linux-wireless@vger.kernel.org
 L:	wil6210@qca.qualcomm.com
 S:	Supported
@@ -1931,7 +1931,7 @@ S:	Supported
 F:	drivers/i2c/busses/i2c-at91.c
 
 ATMEL ISI DRIVER
-M:	Josh Wu <josh.wu@atmel.com>
+M:	Ludovic Desroches <ludovic.desroches@atmel.com>
 L:	linux-media@vger.kernel.org
 S:	Supported
 F:	drivers/media/platform/soc_camera/atmel-isi.c
@@ -1950,7 +1950,8 @@ S:	Supported
 F:	drivers/net/ethernet/cadence/
 
 ATMEL NAND DRIVER
-M:	Josh Wu <josh.wu@atmel.com>
+M:	Wenyou Yang <wenyou.yang@atmel.com>
+M:	Josh Wu <rainyfeeling@outlook.com>
 L:	linux-mtd@lists.infradead.org
 S:	Supported
 F:	drivers/mtd/nand/atmel_nand*
@@ -1992,7 +1993,7 @@ L:	linux-wireless@vger.kernel.org
 W:	http://www.thekelleys.org.uk/atmel
 W:	http://atmelwlandriver.sourceforge.net/
 S:	Maintained
-F:	drivers/net/wireless/atmel*
+F:	drivers/net/wireless/atmel/atmel*
 
 ATMEL MAXTOUCH DRIVER
 M:	Nick Dyer <nick.dyer@itdev.co.uk>
@@ -2081,7 +2082,7 @@ L:	linux-wireless@vger.kernel.org
 L:	b43-dev@lists.infradead.org
 W:	http://wireless.kernel.org/en/users/Drivers/b43
 S:	Odd Fixes
-F:	drivers/net/wireless/b43/
+F:	drivers/net/wireless/broadcom/b43/
 
 B43LEGACY WIRELESS DRIVER
 M:	Larry Finger <Larry.Finger@lwfinger.net>
@@ -2089,7 +2090,7 @@ L:	linux-wireless@vger.kernel.org
 L:	b43-dev@lists.infradead.org
 W:	http://wireless.kernel.org/en/users/Drivers/b43
 S:	Maintained
-F:	drivers/net/wireless/b43legacy/
+F:	drivers/net/wireless/broadcom/b43legacy/
 
 BACKLIGHT CLASS/SUBSYSTEM
 M:	Jingoo Han <jingoohan1@gmail.com>
@@ -2391,7 +2392,7 @@ M:	Hante Meuleman <meuleman@broadcom.com>
 L:	linux-wireless@vger.kernel.org
 L:	brcm80211-dev-list@broadcom.com
 S:	Supported
-F:	drivers/net/wireless/brcm80211/
+F:	drivers/net/wireless/broadcom/brcm80211/
 
 BROADCOM BNX2FC 10 GIGABIT FCOE DRIVER
 M:	QLogic-Storage-Upstream@qlogic.com
@@ -2449,7 +2450,9 @@ F:	drivers/firmware/broadcom/*
 
 BROADCOM STB NAND FLASH DRIVER
 M:	Brian Norris <computersforpeace@gmail.com>
+M:	Kamal Dasu <kdasu.kdev@gmail.com>
 L:	linux-mtd@lists.infradead.org
+L:	bcm-kernel-feedback-list@broadcom.com
 S:	Maintained
 F:	drivers/mtd/nand/brcmnand/
 
@@ -2929,10 +2932,9 @@ S:	Maintained
 F:	drivers/platform/x86/compal-laptop.c
 
 CONEXANT ACCESSRUNNER USB DRIVER
-M:	Simon Arlott <cxacru@fire.lp0.eu>
 L:	accessrunner-general@lists.sourceforge.net
 W:	http://accessrunner.sourceforge.net/
-S:	Maintained
+S:	Orphan
 F:	drivers/usb/atm/cxacru.c
 
 CONFIGFS
@@ -3101,7 +3103,7 @@ F:	sound/pci/cs5535audio/
 CW1200 WLAN driver
 M:	Solomon Peachy <pizza@shaftnet.org>
 S:	Maintained
-F:	drivers/net/wireless/cw1200/
+F:	drivers/net/wireless/st/cw1200/
 
 CX18 VIDEO4LINUX DRIVER
 M:	Andy Walls <awalls@md.metrocast.net>
@@ -4409,6 +4411,7 @@ K:	fmc_d.*register
 
 FPGA MANAGER FRAMEWORK
 M:	Alan Tull <atull@opensource.altera.com>
+R:	Moritz Fischer <moritz.fischer@ettus.com>
 S:	Maintained
 F:	drivers/fpga/
 F:	include/linux/fpga/fpga-mgr.h
@@ -5041,7 +5044,7 @@ L:	hostap@shmoo.com (subscribers-only)
 L:	linux-wireless@vger.kernel.org
 W:	http://hostap.epitest.fi/
 S:	Maintained
-F:	drivers/net/wireless/hostap/
+F:	drivers/net/wireless/intersil/hostap/
 
 HP COMPAQ TC1100 TABLET WMI EXTRAS DRIVER
 L:	platform-driver-x86@vger.kernel.org
@@ -5609,7 +5612,7 @@ L:	linux-wireless@vger.kernel.org
 S:	Maintained
 F:	Documentation/networking/README.ipw2100
 F:	Documentation/networking/README.ipw2200
-F:	drivers/net/wireless/ipw2x00/
+F:	drivers/net/wireless/intel/ipw2x00/
 
 INTEL(R) TRACE HUB
 M:	Alexander Shishkin <alexander.shishkin@linux.intel.com>
@@ -5643,7 +5646,7 @@ INTEL WIRELESS 3945ABG/BG, 4965AGN (iwlegacy)
 M:	Stanislaw Gruszka <sgruszka@redhat.com>
 L:	linux-wireless@vger.kernel.org
 S:	Supported
-F:	drivers/net/wireless/iwlegacy/
+F:	drivers/net/wireless/intel/iwlegacy/
 
 INTEL WIRELESS WIFI LINK (iwlwifi)
 M:	Johannes Berg <johannes.berg@intel.com>
@@ -5653,7 +5656,7 @@ L:	linux-wireless@vger.kernel.org
 W:	http://intellinuxwireless.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi.git
 S:	Supported
-F:	drivers/net/wireless/iwlwifi/
+F:	drivers/net/wireless/intel/iwlwifi/
 
 INTEL MANAGEMENT ENGINE (mei)
 M:	Tomas Winkler <tomas.winkler@intel.com>
@@ -6364,6 +6367,7 @@ F:	arch/*/include/asm/pmem.h
 LIGHTNVM PLATFORM SUPPORT
 M:	Matias Bjorling <mb@lightnvm.io>
 W:	http://github/OpenChannelSSD
+L:	linux-block@vger.kernel.org
 S:	Maintained
 F:	drivers/lightnvm/
 F:	include/linux/lightnvm.h
@@ -6703,7 +6707,7 @@ F:	drivers/net/ethernet/marvell/sk*
 MARVELL LIBERTAS WIRELESS DRIVER
 L:	libertas-dev@lists.infradead.org
 S:	Orphan
-F:	drivers/net/wireless/libertas/
+F:	drivers/net/wireless/marvell/libertas/
 
 MARVELL MV643XX ETHERNET DRIVER
 M:	Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
@@ -6723,13 +6727,13 @@ M:	Amitkumar Karwar <akarwar@marvell.com>
 M:	Nishant Sarmukadam <nishants@marvell.com>
 L:	linux-wireless@vger.kernel.org
 S:	Maintained
-F:	drivers/net/wireless/mwifiex/
+F:	drivers/net/wireless/marvell/mwifiex/
 
 MARVELL MWL8K WIRELESS DRIVER
 M:	Lennert Buytenhek <buytenh@wantstofly.org>
 L:	linux-wireless@vger.kernel.org
 S:	Odd Fixes
-F:	drivers/net/wireless/mwl8k.c
+F:	drivers/net/wireless/marvell/mwl8k.c
 
 MARVELL SOC MMC/SD/SDIO CONTROLLER DRIVER
 M:	Nicolas Pitre <nico@fluxnic.net>
@@ -7364,6 +7368,13 @@ F:	include/net/netrom.h
 F:	include/uapi/linux/netrom.h
 F:	net/netrom/
 
+NETRONOME ETHERNET DRIVERS
+M:	Jakub Kicinski <jakub.kicinski@netronome.com>
+M:	Rolf Neugebauer <rolf.neugebauer@netronome.com>
+L:	oss-drivers@netronome.com
+S:	Maintained
+F:	drivers/net/ethernet/netronome/
+
 NETWORK BLOCK DEVICE (NBD)
 M:	Markus Pargmann <mpa@pengutronix.de>
 S:	Maintained
@@ -7902,6 +7913,18 @@ S:	Maintained
 F:	net/openvswitch/
 F:	include/uapi/linux/openvswitch.h
 
+OPERATING PERFORMANCE POINTS (OPP)
+M:	Viresh Kumar <vireshk@kernel.org>
+M:	Nishanth Menon <nm@ti.com>
+M:	Stephen Boyd <sboyd@codeaurora.org>
+L:	linux-pm@vger.kernel.org
+S:	Maintained
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm.git
+F:	drivers/base/power/opp/
+F:	include/linux/pm_opp.h
+F:	Documentation/power/opp.txt
+F:	Documentation/devicetree/bindings/opp/
+
 OPL4 DRIVER
 M:	Clemens Ladisch <clemens@ladisch.de>
 L:	alsa-devel@alsa-project.org (moderated for non-subscribers)
@@ -7933,7 +7956,7 @@ L:	linux-wireless@vger.kernel.org
 W:	http://wireless.kernel.org/en/users/Drivers/orinoco
 W:	http://www.nongnu.org/orinoco/
 S:	Orphan
-F:	drivers/net/wireless/orinoco/
+F:	drivers/net/wireless/intersil/orinoco/
 
 OSD LIBRARY and FILESYSTEM
 M:	Boaz Harrosh <ooo@electrozaur.com>
@@ -7959,7 +7982,7 @@ M:	Christian Lamparter <chunkeey@googlemail.com>
 L:	linux-wireless@vger.kernel.org
 W:	http://wireless.kernel.org/en/users/Drivers/p54
 S:	Maintained
-F:	drivers/net/wireless/p54/
+F:	drivers/net/wireless/intersil/p54/
 
 PA SEMI ETHERNET DRIVER
 M:	Olof Johansson <olof@lixom.net>
@@ -8501,7 +8524,7 @@ M:	"Luis R. Rodriguez" <mcgrof@gmail.com>
 L:	linux-wireless@vger.kernel.org
 W:	http://wireless.kernel.org/en/users/Drivers/p54
 S:	Obsolete
-F:	drivers/net/wireless/prism54/
+F:	drivers/net/wireless/intersil/prism54/
 
 PS3 NETWORK SUPPORT
 M:	Geoff Levand <geoff@infradead.org>
@@ -8804,7 +8827,7 @@ M:	Stanislaw Gruszka <sgruszka@redhat.com>
 M:	Helmut Schaa <helmut.schaa@googlemail.com>
 L:	linux-wireless@vger.kernel.org
 S:	Maintained
-F:	drivers/net/wireless/rt2x00/
+F:	drivers/net/wireless/ralink/rt2x00/
 
 RAMDISK RAM BLOCK DEVICE DRIVER
 M:	Jens Axboe <axboe@kernel.dk>
@@ -9038,7 +9061,7 @@ L:	linux-wireless@vger.kernel.org
 W:	http://wireless.kernel.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-testing.git
 S:	Orphan
-F:	drivers/net/wireless/rtl818x/rtl8180/
+F:	drivers/net/wireless/realtek/rtl818x/rtl8180/
 
 RTL8187 WIRELESS DRIVER
 M:	Herton Ronaldo Krzesinski <herton@canonical.com>
@@ -9048,7 +9071,7 @@ L:	linux-wireless@vger.kernel.org
 W:	http://wireless.kernel.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-testing.git
 S:	Maintained
-F:	drivers/net/wireless/rtl818x/rtl8187/
+F:	drivers/net/wireless/realtek/rtl818x/rtl8187/
 
 RTL8192CE WIRELESS DRIVER
 M:	Larry Finger <Larry.Finger@lwfinger.net>
@@ -9057,8 +9080,8 @@ L:	linux-wireless@vger.kernel.org
 W:	http://wireless.kernel.org/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-testing.git
 S:	Maintained
-F:	drivers/net/wireless/rtlwifi/
-F:	drivers/net/wireless/rtlwifi/rtl8192ce/
+F:	drivers/net/wireless/realtek/rtlwifi/
+F:	drivers/net/wireless/realtek/rtlwifi/rtl8192ce/
 
 RTL8XXXU WIRELESS DRIVER (rtl8xxxu)
 M:	Jes Sorensen <Jes.Sorensen@redhat.com>
@@ -9315,7 +9338,6 @@ F:	drivers/i2c/busses/i2c-designware-*
 F:	include/linux/platform_data/i2c-designware.h
 
 SYNOPSYS DESIGNWARE MMC/SD/SDIO DRIVER
-M:	Seungwon Jeon <tgih.jun@samsung.com>
 M:	Jaehoon Chung <jh80.chung@samsung.com>
 L:	linux-mmc@vger.kernel.org
 S:	Maintained
@@ -10888,9 +10910,9 @@ S:	Maintained
 F:	drivers/media/tuners/tua9001*
 
 TULIP NETWORK DRIVERS
-M:	Grant Grundler <grundler@parisc-linux.org>
 L:	netdev@vger.kernel.org
-S:	Maintained
+L:	linux-parisc@vger.kernel.org
+S:	Orphan
 F:	drivers/net/ethernet/dec/tulip/
 
 TUN/TAP driver
@@ -11159,6 +11181,13 @@ L:	linux-usb@vger.kernel.org
 S:	Supported
 F:	drivers/usb/class/usblp.c
 
+USB QMI WWAN NETWORK DRIVER
+M:	Bjørn Mork <bjorn@mork.no>
+L:	netdev@vger.kernel.org
+S:	Maintained
+F:	Documentation/ABI/testing/sysfs-class-net-qmi
+F:	drivers/net/usb/qmi_wwan.c
+
 USB RTL8150 DRIVER
 M:	Petko Manolov <petkan@nucleusys.com>
 L:	linux-usb@vger.kernel.org
@@ -11255,7 +11284,7 @@ USB ZD1201 DRIVER
 L:	linux-wireless@vger.kernel.org
 W:	http://linux-lc100020.sourceforge.net
 S:	Orphan
-F:	drivers/net/wireless/zd1201.*
+F:	drivers/net/wireless/zydas/zd1201.*
 
 USB ZR364XX DRIVER
 M:	Antoine Jacquet <royale@zerezo.com>
@@ -11886,7 +11915,7 @@ W:	http://zd1211.ath.cx/wiki/DriverRewrite
 L:	linux-wireless@vger.kernel.org
 L:	zd1211-devs@lists.sourceforge.net (subscribers-only)
 S:	Maintained
-F:	drivers/net/wireless/zd1211rw/
+F:	drivers/net/wireless/zydas/zd1211rw/
 
 ZPOOL COMPRESSED PAGE STORAGE API
 M:	Dan Streetman <ddstreet@ieee.org>

Makefile

@@ -1,7 +1,7 @@
 VERSION = 4
 PATCHLEVEL = 4
 SUBLEVEL = 0
-EXTRAVERSION = -rc1
+EXTRAVERSION = -rc3
 NAME = Blurry Fish Butt
 
 # *DOCUMENTATION*

arch/arc/configs/axs101_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y

arch/arc/configs/axs103_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y

arch/arc/configs/axs103_smp_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y

arch/arc/configs/nsim_hs_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set

arch/arc/configs/nsim_hs_smp_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set

arch/arc/configs/nsimosci_hs_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set

arch/arc/configs/nsimosci_hs_smp_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y

arch/arc/configs/vdk_hs38_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_CROSS_MEMORY_ATTACH is not set

arch/arc/configs/vdk_hs38_smp_defconfig

@@ -1,4 +1,4 @@
-CONFIG_CROSS_COMPILE="arc-linux-uclibc-"
+CONFIG_CROSS_COMPILE="arc-linux-"
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_DEFAULT_HOSTNAME="ARCLinux"
 # CONFIG_CROSS_MEMORY_ATTACH is not set

arch/arc/include/asm/irqflags-arcv2.h

@@ -37,6 +37,9 @@
 #define ISA_INIT_STATUS_BITS	(STATUS_IE_MASK | STATUS_AD_MASK | \
 					(ARCV2_IRQ_DEF_PRIO << 1))
 
+/* SLEEP needs default irq priority (<=) which can interrupt the doze */
+#define ISA_SLEEP_ARG		(0x10 | ARCV2_IRQ_DEF_PRIO)
+
 #ifndef __ASSEMBLY__
 
 /*

arch/arc/include/asm/irqflags-compact.h

@@ -43,6 +43,8 @@
 
 #define ISA_INIT_STATUS_BITS	STATUS_IE_MASK
 
+#define ISA_SLEEP_ARG		0x3
+
 #ifndef __ASSEMBLY__
 
 /******************************************************************

arch/arc/kernel/ctx_sw.c

@@ -58,8 +58,6 @@ __switch_to(struct task_struct *prev_task, struct task_struct *next_task)
 		"st      sp, [r24]       \n\t"
 #endif
 
-		"sync   \n\t"
-
 		/*
 		 * setup _current_task with incoming tsk.
 		 * optionally, set r25 to that as well

arch/arc/kernel/ctx_sw_asm.S

@@ -44,9 +44,6 @@ __switch_to:
 	* don't need to do anything special to return it
 	*/
 
-	/* hardware memory barrier */
-	sync
-
 	/*
 	 * switch to new task, contained in r1
 	 * Temp reg r3 is required to get the ptr to store val

arch/arc/kernel/process.c

@@ -44,11 +44,10 @@ SYSCALL_DEFINE0(arc_gettls)
 void arch_cpu_idle(void)
 {
 	/* sleep, but enable all interrupts before committing */
-	if (is_isa_arcompact()) {
-		__asm__("sleep 0x3");
-	} else {
-		__asm__("sleep 0x10");
-	}
+	__asm__ __volatile__(
+		"sleep %0	\n"
+		:
+		:"I"(ISA_SLEEP_ARG)); /* can't be "r" has to be embedded const */
 }
 
 asmlinkage void ret_from_fork(void);

arch/arc/kernel/unwind.c

@@ -986,42 +986,13 @@ int arc_unwind(struct unwind_frame_info *frame)
 							    (const u8 *)(fde +
 									 1) +
 							    *fde, ptrType);
-				if (pc >= endLoc)
+				if (pc >= endLoc) {
 					fde = NULL;
-			} else
-				fde = NULL;
-		}
-		if (fde == NULL) {
-			for (fde = table->address, tableSize = table->size;
-			     cie = NULL, tableSize > sizeof(*fde)
-			     && tableSize - sizeof(*fde) >= *fde;
-			     tableSize -= sizeof(*fde) + *fde,
-			     fde += 1 + *fde / sizeof(*fde)) {
-				cie = cie_for_fde(fde, table);
-				if (cie == &bad_cie) {
 					cie = NULL;
-					break;
 				}
-				if (cie == NULL
-				    || cie == &not_fde
-				    || (ptrType = fde_pointer_type(cie)) < 0)
-					continue;
-				ptr = (const u8 *)(fde + 2);
-				startLoc = read_pointer(&ptr,
-							(const u8 *)(fde + 1) +
-							*fde, ptrType);
-				if (!startLoc)
-					continue;
-				if (!(ptrType & DW_EH_PE_indirect))
-					ptrType &=
-					    DW_EH_PE_FORM | DW_EH_PE_signed;
-				endLoc =
-				    startLoc + read_pointer(&ptr,
-							    (const u8 *)(fde +
-									 1) +
-							    *fde, ptrType);
-				if (pc >= startLoc && pc < endLoc)
-					break;
+			} else {
+				fde = NULL;
+				cie = NULL;
 			}
 		}
 	}

arch/arc/mm/tlb.c

@@ -619,10 +619,10 @@ void update_mmu_cache(struct vm_area_struct *vma, unsigned long vaddr_unaligned,
 
 		int dirty = !test_and_set_bit(PG_dc_clean, &page->flags);
 		if (dirty) {
-			/* wback + inv dcache lines */
+			/* wback + inv dcache lines (K-mapping) */
 			__flush_dcache_page(paddr, paddr);
 
-			/* invalidate any existing icache lines */
+			/* invalidate any existing icache lines (U-mapping) */
 			if (vma->vm_flags & VM_EXEC)
 				__inv_icache_page(paddr, vaddr);
 		}

arch/arm/Kconfig

@@ -76,6 +76,8 @@ config ARM
 	select IRQ_FORCED_THREADING
 	select MODULES_USE_ELF_REL
 	select NO_BOOTMEM
+	select OF_EARLY_FLATTREE if OF
+	select OF_RESERVED_MEM if OF
 	select OLD_SIGACTION
 	select OLD_SIGSUSPEND3
 	select PERF_USE_VMALLOC
@@ -1822,8 +1824,6 @@ config USE_OF
 	bool "Flattened Device Tree support"
 	select IRQ_DOMAIN
 	select OF
-	select OF_EARLY_FLATTREE
-	select OF_RESERVED_MEM
 	help
 	  Include support for flattened device tree machine descriptions.
 

arch/arm/boot/dts/am57xx-beagle-x15.dts

@@ -604,6 +604,7 @@
 		reg = <0x6f>;
 		interrupts-extended = <&crossbar_mpu GIC_SPI 2 IRQ_TYPE_EDGE_RISING>,
 				      <&dra7_pmx_core 0x424>;
+		interrupt-names = "irq", "wakeup";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&mcp79410_pins_default>;

arch/arm/boot/dts/animeo_ip.dts

@@ -155,21 +155,21 @@
 			label = "keyswitch_in";
 			gpios = <&pioB 1 GPIO_ACTIVE_HIGH>;
 			linux,code = <28>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		error_in {
 			label = "error_in";
 			gpios = <&pioB 2 GPIO_ACTIVE_HIGH>;
 			linux,code = <29>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		btn {
 			label = "btn";
 			gpios = <&pioC 23 GPIO_ACTIVE_HIGH>;
 			linux,code = <31>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 };

arch/arm/boot/dts/armada-38x.dtsi

@@ -498,6 +498,7 @@
 				reg = <0x70000 0x4000>;
 				interrupts-extended = <&mpic 8>;
 				clocks = <&gateclk 4>;
+				tx-csum-limit = <9800>;
 				status = "disabled";
 			};
 

arch/arm/boot/dts/at91-foxg20.dts

@@ -159,7 +159,7 @@
 			label = "Button";
 			gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 };

arch/arm/boot/dts/at91-kizbox.dts

@@ -24,15 +24,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <18432000>;
-		};
-
 		main_xtal {
 			clock-frequency = <18432000>;
 		};
@@ -94,14 +85,14 @@
 			label = "PB_RST";
 			gpios = <&pioB 30 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x100>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		user {
 			label = "PB_USER";
 			gpios = <&pioB 31 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x101>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91-kizbox2.dts

@@ -171,21 +171,21 @@
 			label = "PB_PROG";
 			gpios = <&pioE 27 GPIO_ACTIVE_LOW>;
 			linux,code = <0x102>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		reset {
 			label = "PB_RST";
 			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
 			linux,code = <0x100>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		user {
 			label = "PB_USER";
 			gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x101>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91-kizboxmini.dts

@@ -98,14 +98,14 @@
 			label = "PB_PROG";
 			gpios = <&pioC 17 GPIO_ACTIVE_LOW>;
 			linux,code = <0x102>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		reset {
 			label = "PB_RST";
 			gpios = <&pioC 16 GPIO_ACTIVE_LOW>;
 			linux,code = <0x100>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91-qil_a9260.dts

@@ -183,7 +183,7 @@
 			label = "user_pb";
 			gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91-sama5d2_xplained.dts

@@ -45,6 +45,7 @@
 /dts-v1/;
 #include "sama5d2.dtsi"
 #include "sama5d2-pinfunc.h"
+#include <dt-bindings/mfd/atmel-flexcom.h>
 
 / {
 	model = "Atmel SAMA5D2 Xplained";
@@ -59,15 +60,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <12000000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -91,6 +83,22 @@
 			status = "okay";
 		};
 
+		sdmmc0: sdio-host@a0000000 {
+			bus-width = <8>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc0_default>;
+			non-removable;
+			mmc-ddr-1_8v;
+			status = "okay";
+		};
+
+		sdmmc1: sdio-host@b0000000 {
+			bus-width = <4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sdmmc1_default>;
+			status = "okay"; /* conflict with qspi0 */
+		};
+
 		apb {
 			spi0: spi@f8000000 {
 				pinctrl-names = "default";
@@ -181,12 +189,49 @@
 				};
 			};
 
+			flx0: flexcom@f8034000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+				status = "disabled"; /* conflict with ISC_D2 & ISC_D3 data pins */
+
+				uart5: serial@200 {
+					compatible = "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&flx0_clk>;
+					clock-names = "usart";
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx0_default>;
+					atmel,fifo-size = <32>;
+					status = "okay";
+				};
+			};
+
 			uart3: serial@fc008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart3_default>;
 				status = "okay";
 			};
 
+			flx4: flexcom@fc018000 {
+				atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+				status = "okay";
+
+				i2c2: i2c@600 {
+					compatible = "atmel,sama5d2-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <0>, <0>;
+					dma-names = "tx", "rx";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					clocks = <&flx4_clk>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_flx4_default>;
+					atmel,fifo-size = <16>;
+					status = "okay";
+				};
+			};
+
 			i2c1: i2c@fc028000 {
 				dmas = <0>, <0>;
 				pinctrl-names = "default";
@@ -201,6 +246,18 @@
 			};
 
 			pinctrl@fc038000 {
+				pinctrl_flx0_default: flx0_default {
+					pinmux = <PIN_PB28__FLEXCOM0_IO0>,
+						 <PIN_PB29__FLEXCOM0_IO1>;
+					bias-disable;
+				};
+
+				pinctrl_flx4_default: flx4_default {
+					pinmux = <PIN_PD12__FLEXCOM4_IO0>,
+						 <PIN_PD13__FLEXCOM4_IO1>;
+					bias-disable;
+				};
+
 				pinctrl_i2c0_default: i2c0_default {
 					pinmux = <PIN_PD21__TWD0>,
 						 <PIN_PD22__TWCK0>;
@@ -227,6 +284,46 @@
 					bias-disable;
 				};
 
+				pinctrl_sdmmc0_default: sdmmc0_default {
+					cmd_data {
+						pinmux = <PIN_PA1__SDMMC0_CMD>,
+							 <PIN_PA2__SDMMC0_DAT0>,
+							 <PIN_PA3__SDMMC0_DAT1>,
+							 <PIN_PA4__SDMMC0_DAT2>,
+							 <PIN_PA5__SDMMC0_DAT3>,
+							 <PIN_PA6__SDMMC0_DAT4>,
+							 <PIN_PA7__SDMMC0_DAT5>,
+							 <PIN_PA8__SDMMC0_DAT6>,
+							 <PIN_PA9__SDMMC0_DAT7>;
+						bias-pull-up;
+					};
+
+					ck_cd_rstn_vddsel {
+						pinmux = <PIN_PA0__SDMMC0_CK>,
+							 <PIN_PA10__SDMMC0_RSTN>,
+							 <PIN_PA11__SDMMC0_VDDSEL>,
+							 <PIN_PA13__SDMMC0_CD>;
+						bias-disable;
+					};
+				};
+
+				pinctrl_sdmmc1_default: sdmmc1_default {
+					cmd_data {
+						pinmux = <PIN_PA28__SDMMC1_CMD>,
+							 <PIN_PA18__SDMMC1_DAT0>,
+							 <PIN_PA19__SDMMC1_DAT1>,
+							 <PIN_PA20__SDMMC1_DAT2>,
+							 <PIN_PA21__SDMMC1_DAT3>;
+						bias-pull-up;
+					};
+
+					conf-ck_cd {
+						pinmux = <PIN_PA22__SDMMC1_CK>,
+							 <PIN_PA30__SDMMC1_CD>;
+						bias-disable;
+					};
+				};
+
 				pinctrl_spi0_default: spi0_default {
 					pinmux = <PIN_PA14__SPI0_SPCK>,
 						 <PIN_PA15__SPI0_MOSI>,

arch/arm/boot/dts/at91-sama5d3_xplained.dts

@@ -315,7 +315,7 @@
 			label = "PB_USER";
 			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
 			linux,code = <0x104>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91-sama5d4_xplained.dts

@@ -50,7 +50,6 @@
 	compatible = "atmel,sama5d4-xplained", "atmel,sama5d4", "atmel,sama5";
 
 	chosen {
-		bootargs = "ignore_loglevel earlyprintk";
 		stdout-path = "serial0:115200n8";
 	};
 
@@ -59,15 +58,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <12000000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -235,7 +225,7 @@
 			label = "pb_user1";
 			gpios = <&pioE 8 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x100>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91-sama5d4ek.dts

@@ -50,7 +50,6 @@
 	compatible = "atmel,sama5d4ek", "atmel,sama5d4", "atmel,sama5";
 
 	chosen {
-		bootargs = "ignore_loglevel earlyprintk";
 		stdout-path = "serial0:115200n8";
 	};
 
@@ -59,15 +58,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <12000000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -304,7 +294,7 @@
 			label = "pb_user1";
 			gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x100>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91rm9200ek.dts

@@ -21,15 +21,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <18432000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};

arch/arm/boot/dts/at91sam9261ek.dts

@@ -22,15 +22,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <18432000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -149,7 +140,7 @@
 					ti,debounce-tol = /bits/ 16 <65535>;
 					ti,debounce-max = /bits/ 16 <1>;
 
-					linux,wakeup;
+					wakeup-source;
 				};
 			};
 
@@ -193,28 +184,28 @@
 			label = "button_0";
 			gpios = <&pioA 27 GPIO_ACTIVE_LOW>;
 			linux,code = <256>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		button_1 {
 			label = "button_1";
 			gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
 			linux,code = <257>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		button_2 {
 			label = "button_2";
 			gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
 			linux,code = <258>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		button_3 {
 			label = "button_3";
 			gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
 			linux,code = <259>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 };

arch/arm/boot/dts/at91sam9263ek.dts

@@ -22,15 +22,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <16367660>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -213,14 +204,14 @@
 			label = "left_click";
 			gpios = <&pioC 5 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		right_click {
 			label = "right_click";
 			gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91sam9g20ek_common.dtsi

@@ -19,15 +19,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <18432000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -206,14 +197,14 @@
 			label = "Button 3";
 			gpios = <&pioA 30 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		btn4 {
 			label = "Button 4";
 			gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
 			linux,code = <0x104>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91sam9m10g45ek.dts

@@ -24,15 +24,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <12000000>;
-		};
-
 		slow_xtal {
 		      clock-frequency = <32768>;
 		};
@@ -323,14 +314,14 @@
 			label = "left_click";
 			gpios = <&pioB 6 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		right_click {
 			label = "right_click";
 			gpios = <&pioB 7 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		left {

arch/arm/boot/dts/at91sam9n12ek.dts

@@ -23,15 +23,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <16000000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -219,7 +210,7 @@
 			label = "Enter";
 			gpios = <&pioB 3 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91sam9rlek.dts

@@ -22,15 +22,6 @@
 	};
 
 	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <12000000>;
-		};
-
 		slow_xtal {
 			clock-frequency = <32768>;
 		};
@@ -225,14 +216,14 @@
 			label = "right_click";
 			gpios = <&pioB 0 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 
 		left_click {
 			label = "left_click";
 			gpios = <&pioB 1 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/at91sam9x5cm.dtsi

@@ -12,17 +12,6 @@
 		reg = <0x20000000 0x8000000>;
 	};
 
-	clocks {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		main_clock: clock@0 {
-			compatible = "atmel,osc", "fixed-clock";
-			clock-frequency = <12000000>;
-		};
-	};
-
 	clocks {
 		slow_xtal {
 			clock-frequency = <32768>;

arch/arm/boot/dts/dra7.dtsi

@@ -1459,8 +1459,8 @@
 			interrupt-names = "tx", "rx";
 			dmas = <&sdma_xbar 133>, <&sdma_xbar 132>;
 			dma-names = "tx", "rx";
-			clocks = <&mcasp3_ahclkx_mux>;
-			clock-names = "fck";
+			clocks = <&mcasp3_aux_gfclk_mux>, <&mcasp3_ahclkx_mux>;
+			clock-names = "fck", "ahclkx";
 			status = "disabled";
 		};
 

arch/arm/boot/dts/imx27.dtsi

@@ -486,7 +486,10 @@
 				compatible = "fsl,imx27-usb";
 				reg = <0x10024000 0x200>;
 				interrupts = <56>;
-				clocks = <&clks IMX27_CLK_USB_IPG_GATE>;
+				clocks = <&clks IMX27_CLK_USB_IPG_GATE>,
+					<&clks IMX27_CLK_USB_AHB_GATE>,
+					<&clks IMX27_CLK_USB_DIV>;
+				clock-names = "ipg", "ahb", "per";
 				fsl,usbmisc = <&usbmisc 0>;
 				status = "disabled";
 			};
@@ -495,7 +498,10 @@
 				compatible = "fsl,imx27-usb";
 				reg = <0x10024200 0x200>;
 				interrupts = <54>;
-				clocks = <&clks IMX27_CLK_USB_IPG_GATE>;
+				clocks = <&clks IMX27_CLK_USB_IPG_GATE>,
+					<&clks IMX27_CLK_USB_AHB_GATE>,
+					<&clks IMX27_CLK_USB_DIV>;
+				clock-names = "ipg", "ahb", "per";
 				fsl,usbmisc = <&usbmisc 1>;
 				dr_mode = "host";
 				status = "disabled";
@@ -505,7 +511,10 @@
 				compatible = "fsl,imx27-usb";
 				reg = <0x10024400 0x200>;
 				interrupts = <55>;
-				clocks = <&clks IMX27_CLK_USB_IPG_GATE>;
+				clocks = <&clks IMX27_CLK_USB_IPG_GATE>,
+					<&clks IMX27_CLK_USB_AHB_GATE>,
+					<&clks IMX27_CLK_USB_DIV>;
+				clock-names = "ipg", "ahb", "per";
 				fsl,usbmisc = <&usbmisc 2>;
 				dr_mode = "host";
 				status = "disabled";
@@ -515,7 +524,6 @@
 				#index-cells = <1>;
 				compatible = "fsl,imx27-usbmisc";
 				reg = <0x10024600 0x200>;
-				clocks = <&clks IMX27_CLK_USB_AHB_GATE>;
 			};
 
 			sahara2: sahara@10025000 {

arch/arm/boot/dts/k2l-netcp.dtsi

@@ -137,7 +137,7 @@ netcp: netcp@26000000 {
 	/* NetCP address range */
 	ranges = <0 0x26000000 0x1000000>;
 
-	clocks = <&papllclk>, <&clkcpgmac>, <&chipclk12>;
+	clocks = <&clkosr>, <&papllclk>, <&clkcpgmac>, <&chipclk12>;
 	dma-coherent;
 
 	ti,navigator-dmas = <&dma_gbe 0>,

arch/arm/boot/dts/kirkwood-ts219.dtsi

@@ -40,7 +40,7 @@
 		};
 		poweroff@12100 {
 			compatible = "qnap,power-off";
-			reg = <0x12000 0x100>;
+			reg = <0x12100 0x100>;
 			clocks = <&gate_clk 7>;
 		};
 		spi@10600 {

arch/arm/boot/dts/rk3288-veyron-minnie.dts

@@ -86,6 +86,10 @@
 	};
 };
 
+&emmc {
+	/delete-property/mmc-hs200-1_8v;
+};
+
 &gpio_keys {
 	pinctrl-0 = <&pwr_key_l &ap_lid_int_l &volum_down_l &volum_up_l>;
 

arch/arm/boot/dts/rk3288.dtsi

@@ -452,8 +452,10 @@
 		clock-names = "tsadc", "apb_pclk";
 		resets = <&cru SRST_TSADC>;
 		reset-names = "tsadc-apb";
-		pinctrl-names = "default";
-		pinctrl-0 = <&otp_out>;
+		pinctrl-names = "init", "default", "sleep";
+		pinctrl-0 = <&otp_gpio>;
+		pinctrl-1 = <&otp_out>;
+		pinctrl-2 = <&otp_gpio>;
 		#thermal-sensor-cells = <1>;
 		rockchip,hw-tshut-temp = <95000>;
 		status = "disabled";
@@ -1395,6 +1397,10 @@
 		};
 
 		tsadc {
+			otp_gpio: otp-gpio {
+				rockchip,pins = <0 10 RK_FUNC_GPIO &pcfg_pull_none>;
+			};
+
 			otp_out: otp-out {
 				rockchip,pins = <0 10 RK_FUNC_1 &pcfg_pull_none>;
 			};

arch/arm/boot/dts/sama5d35ek.dts

@@ -49,7 +49,7 @@
 			label = "pb_user1";
 			gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x100>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 };

arch/arm/boot/dts/sama5d4.dtsi

@@ -1300,7 +1300,7 @@
 			};
 
 			watchdog@fc068640 {
-				compatible = "atmel,at91sam9260-wdt";
+				compatible = "atmel,sama5d4-wdt";
 				reg = <0xfc068640 0x10>;
 				clocks = <&clk32k>;
 				status = "disabled";

arch/arm/boot/dts/usb_a9260_common.dtsi

@@ -115,7 +115,7 @@
 			label = "user_pb";
 			gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/usb_a9263.dts

@@ -143,7 +143,7 @@
 			label = "user_pb";
 			gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
-			gpio-key,wakeup;
+			wakeup-source;
 		};
 	};
 

arch/arm/boot/dts/vfxxx.dtsi

@@ -158,7 +158,7 @@
 				interrupts = <67 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_DSPI0>;
 				clock-names = "dspi";
-				spi-num-chipselects = <5>;
+				spi-num-chipselects = <6>;
 				status = "disabled";
 			};
 
@@ -170,7 +170,7 @@
 				interrupts = <68 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks VF610_CLK_DSPI1>;
 				clock-names = "dspi";
-				spi-num-chipselects = <5>;
+				spi-num-chipselects = <4>;
 				status = "disabled";
 			};
 
@@ -461,6 +461,8 @@
 				clock-names = "adc";
 				#io-channel-cells = <1>;
 				status = "disabled";
+				fsl,adck-max-frequency = <30000000>, <40000000>,
+							<20000000>;
 			};
 
 			esdhc0: esdhc@400b1000 {
@@ -472,8 +474,6 @@
 					<&clks VF610_CLK_ESDHC0>;
 				clock-names = "ipg", "ahb", "per";
 				status = "disabled";
-				fsl,adck-max-frequency = <30000000>, <40000000>,
-							<20000000>;
 			};
 
 			esdhc1: esdhc@400b2000 {

arch/arm/configs/at91_dt_defconfig

@@ -125,7 +125,6 @@ CONFIG_POWER_RESET=y
 # CONFIG_HWMON is not set
 CONFIG_WATCHDOG=y
 CONFIG_AT91SAM9X_WATCHDOG=y
-CONFIG_SSB=m
 CONFIG_MFD_ATMEL_HLCDC=y
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y

arch/arm/configs/sama5_defconfig

@@ -129,7 +129,6 @@ CONFIG_GPIO_SYSFS=y
 CONFIG_POWER_SUPPLY=y
 CONFIG_POWER_RESET=y
 # CONFIG_HWMON is not set
-CONFIG_SSB=m
 CONFIG_MFD_ATMEL_FLEXCOM=y
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y

arch/arm/include/asm/irq.h

@@ -40,6 +40,11 @@ extern void arch_trigger_all_cpu_backtrace(bool);
 #define arch_trigger_all_cpu_backtrace(x) arch_trigger_all_cpu_backtrace(x)
 #endif
 
+static inline int nr_legacy_irqs(void)
+{
+	return NR_IRQS_LEGACY;
+}
+
 #endif
 
 #endif

arch/arm/include/uapi/asm/unistd.h

@@ -416,6 +416,7 @@
 #define __NR_execveat			(__NR_SYSCALL_BASE+387)
 #define __NR_userfaultfd		(__NR_SYSCALL_BASE+388)
 #define __NR_membarrier			(__NR_SYSCALL_BASE+389)
+#define __NR_mlock2			(__NR_SYSCALL_BASE+390)
 
 /*
  * The following SWIs are ARM private.

arch/arm/kernel/bios32.c

@@ -17,11 +17,6 @@
 #include <asm/mach/pci.h>
 
 static int debug_pci;
-static resource_size_t (*align_resource)(struct pci_dev *dev,
-		  const struct resource *res,
-		  resource_size_t start,
-		  resource_size_t size,
-		  resource_size_t align) = NULL;
 
 /*
  * We can't use pci_get_device() here since we are
@@ -461,7 +456,6 @@ static void pcibios_init_hw(struct device *parent, struct hw_pci *hw,
 		sys->busnr   = busnr;
 		sys->swizzle = hw->swizzle;
 		sys->map_irq = hw->map_irq;
-		align_resource = hw->align_resource;
 		INIT_LIST_HEAD(&sys->resources);
 
 		if (hw->private_data)
@@ -470,6 +464,8 @@ static void pcibios_init_hw(struct device *parent, struct hw_pci *hw,
 		ret = hw->setup(nr, sys);
 
 		if (ret > 0) {
+			struct pci_host_bridge *host_bridge;
+
 			ret = pcibios_init_resources(nr, sys);
 			if (ret)  {
 				kfree(sys);
@@ -491,6 +487,9 @@ static void pcibios_init_hw(struct device *parent, struct hw_pci *hw,
 			busnr = sys->bus->busn_res.end + 1;
 
 			list_add(&sys->node, head);
+
+			host_bridge = pci_find_host_bridge(sys->bus);
+			host_bridge->align_resource = hw->align_resource;
 		} else {
 			kfree(sys);
 			if (ret < 0)
@@ -578,14 +577,18 @@ resource_size_t pcibios_align_resource(void *data, const struct resource *res,
 {
 	struct pci_dev *dev = data;
 	resource_size_t start = res->start;
+	struct pci_host_bridge *host_bridge;
 
 	if (res->flags & IORESOURCE_IO && start & 0x300)
 		start = (start + 0x3ff) & ~0x3ff;
 
 	start = (start + align - 1) & ~(align - 1);
 
-	if (align_resource)
-		return align_resource(dev, res, start, size, align);
+	host_bridge = pci_find_host_bridge(dev->bus);
+
+	if (host_bridge->align_resource)
+		return host_bridge->align_resource(dev, res,
+				start, size, align);
 
 	return start;
 }

arch/arm/kernel/calls.S

@@ -399,6 +399,7 @@
 		CALL(sys_execveat)
 		CALL(sys_userfaultfd)
 		CALL(sys_membarrier)
+		CALL(sys_mlock2)
 #ifndef syscalls_counted
 .equ syscalls_padding, ((NR_syscalls + 3) & ~3) - NR_syscalls
 #define syscalls_counted

arch/arm/kvm/arm.c

@@ -563,18 +563,13 @@ int kvm_arch_vcpu_ioctl_run(struct kvm_vcpu *vcpu, struct kvm_run *run)
 		if (vcpu->arch.power_off || vcpu->arch.pause)
 			vcpu_sleep(vcpu);
 
-		/*
-		 * Disarming the background timer must be done in a
-		 * preemptible context, as this call may sleep.
-		 */
-		kvm_timer_flush_hwstate(vcpu);
-
 		/*
 		 * Preparing the interrupts to be injected also
 		 * involves poking the GIC, which must be done in a
 		 * non-preemptible context.
 		 */
 		preempt_disable();
+		kvm_timer_flush_hwstate(vcpu);
 		kvm_vgic_flush_hwstate(vcpu);
 
 		local_irq_disable();

arch/arm/kvm/mmu.c

@@ -98,6 +98,11 @@ static void kvm_flush_dcache_pud(pud_t pud)
 	__kvm_flush_dcache_pud(pud);
 }
 
+static bool kvm_is_device_pfn(unsigned long pfn)
+{
+	return !pfn_valid(pfn);
+}
+
 /**
  * stage2_dissolve_pmd() - clear and flush huge PMD entry
  * @kvm:	pointer to kvm structure.
@@ -213,7 +218,7 @@ static void unmap_ptes(struct kvm *kvm, pmd_t *pmd,
 			kvm_tlb_flush_vmid_ipa(kvm, addr);
 
 			/* No need to invalidate the cache for device mappings */
-			if ((pte_val(old_pte) & PAGE_S2_DEVICE) != PAGE_S2_DEVICE)
+			if (!kvm_is_device_pfn(__phys_to_pfn(addr)))
 				kvm_flush_dcache_pte(old_pte);
 
 			put_page(virt_to_page(pte));
@@ -305,8 +310,7 @@ static void stage2_flush_ptes(struct kvm *kvm, pmd_t *pmd,
 
 	pte = pte_offset_kernel(pmd, addr);
 	do {
-		if (!pte_none(*pte) &&
-		    (pte_val(*pte) & PAGE_S2_DEVICE) != PAGE_S2_DEVICE)
+		if (!pte_none(*pte) && !kvm_is_device_pfn(__phys_to_pfn(addr)))
 			kvm_flush_dcache_pte(*pte);
 	} while (pte++, addr += PAGE_SIZE, addr != end);
 }
@@ -1037,11 +1041,6 @@ static bool kvm_is_write_fault(struct kvm_vcpu *vcpu)
 	return kvm_vcpu_dabt_iswrite(vcpu);
 }
 
-static bool kvm_is_device_pfn(unsigned long pfn)
-{
-	return !pfn_valid(pfn);
-}
-
 /**
  * stage2_wp_ptes - write protect PMD range
  * @pmd:	pointer to pmd entry

arch/arm/mach-dove/include/mach/entry-macro.S

@@ -18,13 +18,13 @@
 	@ check low interrupts
 	ldr	\irqstat, [\base, #IRQ_CAUSE_LOW_OFF]
 	ldr	\tmp, [\base, #IRQ_MASK_LOW_OFF]
-	mov	\irqnr, #31
+	mov	\irqnr, #32
 	ands	\irqstat, \irqstat, \tmp
 
 	@ if no low interrupts set, check high interrupts
 	ldreq	\irqstat, [\base, #IRQ_CAUSE_HIGH_OFF]
 	ldreq	\tmp, [\base, #IRQ_MASK_HIGH_OFF]
-	moveq	\irqnr, #63
+	moveq	\irqnr, #64
 	andeqs	\irqstat, \irqstat, \tmp
 
 	@ find first active interrupt source

arch/arm/mach-imx/gpc.c

@@ -177,6 +177,7 @@ static struct irq_chip imx_gpc_chip = {
 	.irq_unmask		= imx_gpc_irq_unmask,
 	.irq_retrigger		= irq_chip_retrigger_hierarchy,
 	.irq_set_wake		= imx_gpc_irq_set_wake,
+	.irq_set_type           = irq_chip_set_type_parent,
 #ifdef CONFIG_SMP
 	.irq_set_affinity	= irq_chip_set_affinity_parent,
 #endif

arch/arm/mach-omap2/omap-smp.c

@@ -143,9 +143,9 @@ static int omap4_boot_secondary(unsigned int cpu, struct task_struct *idle)
 		 * Ensure that CPU power state is set to ON to avoid CPU
 		 * powerdomain transition on wfi
 		 */
-		clkdm_wakeup(cpu1_clkdm);
-		omap_set_pwrdm_state(cpu1_pwrdm, PWRDM_POWER_ON);
-		clkdm_allow_idle(cpu1_clkdm);
+		clkdm_wakeup_nolock(cpu1_clkdm);
+		pwrdm_set_next_pwrst(cpu1_pwrdm, PWRDM_POWER_ON);
+		clkdm_allow_idle_nolock(cpu1_clkdm);
 
 		if (IS_PM44XX_ERRATUM(PM_OMAP4_ROM_SMP_BOOT_ERRATUM_GICD)) {
 			while (gic_dist_disabled()) {

arch/arm/mach-omap2/omap_hwmod.c

@@ -890,6 +890,36 @@ static int _init_opt_clks(struct omap_hwmod *oh)
 	return ret;
 }
 
+static void _enable_optional_clocks(struct omap_hwmod *oh)
+{
+	struct omap_hwmod_opt_clk *oc;
+	int i;
+
+	pr_debug("omap_hwmod: %s: enabling optional clocks\n", oh->name);
+
+	for (i = oh->opt_clks_cnt, oc = oh->opt_clks; i > 0; i--, oc++)
+		if (oc->_clk) {
+			pr_debug("omap_hwmod: enable %s:%s\n", oc->role,
+				 __clk_get_name(oc->_clk));
+			clk_enable(oc->_clk);
+		}
+}
+
+static void _disable_optional_clocks(struct omap_hwmod *oh)
+{
+	struct omap_hwmod_opt_clk *oc;
+	int i;
+
+	pr_debug("omap_hwmod: %s: disabling optional clocks\n", oh->name);
+
+	for (i = oh->opt_clks_cnt, oc = oh->opt_clks; i > 0; i--, oc++)
+		if (oc->_clk) {
+			pr_debug("omap_hwmod: disable %s:%s\n", oc->role,
+				 __clk_get_name(oc->_clk));
+			clk_disable(oc->_clk);
+		}
+}
+
 /**
  * _enable_clocks - enable hwmod main clock and interface clocks
  * @oh: struct omap_hwmod *
@@ -917,6 +947,9 @@ static int _enable_clocks(struct omap_hwmod *oh)
 			clk_enable(os->_clk);
 	}
 
+	if (oh->flags & HWMOD_OPT_CLKS_NEEDED)
+		_enable_optional_clocks(oh);
+
 	/* The opt clocks are controlled by the device driver. */
 
 	return 0;
@@ -948,41 +981,14 @@ static int _disable_clocks(struct omap_hwmod *oh)
 			clk_disable(os->_clk);
 	}
 
+	if (oh->flags & HWMOD_OPT_CLKS_NEEDED)
+		_disable_optional_clocks(oh);
+
 	/* The opt clocks are controlled by the device driver. */
 
 	return 0;
 }
 
-static void _enable_optional_clocks(struct omap_hwmod *oh)
-{
-	struct omap_hwmod_opt_clk *oc;
-	int i;
-
-	pr_debug("omap_hwmod: %s: enabling optional clocks\n", oh->name);
-
-	for (i = oh->opt_clks_cnt, oc = oh->opt_clks; i > 0; i--, oc++)
-		if (oc->_clk) {
-			pr_debug("omap_hwmod: enable %s:%s\n", oc->role,
-				 __clk_get_name(oc->_clk));
-			clk_enable(oc->_clk);
-		}
-}
-
-static void _disable_optional_clocks(struct omap_hwmod *oh)
-{
-	struct omap_hwmod_opt_clk *oc;
-	int i;
-
-	pr_debug("omap_hwmod: %s: disabling optional clocks\n", oh->name);
-
-	for (i = oh->opt_clks_cnt, oc = oh->opt_clks; i > 0; i--, oc++)
-		if (oc->_clk) {
-			pr_debug("omap_hwmod: disable %s:%s\n", oc->role,
-				 __clk_get_name(oc->_clk));
-			clk_disable(oc->_clk);
-		}
-}
-
 /**
  * _omap4_enable_module - enable CLKCTRL modulemode on OMAP4
  * @oh: struct omap_hwmod *

arch/arm/mach-omap2/omap_hwmod.h

@@ -523,6 +523,8 @@ struct omap_hwmod_omap4_prcm {
  * HWMOD_RECONFIG_IO_CHAIN: omap_hwmod code needs to reconfigure wake-up 
  *     events by calling _reconfigure_io_chain() when a device is enabled
  *     or idled.
+ * HWMOD_OPT_CLKS_NEEDED: The optional clocks are needed for the module to
+ *     operate and they need to be handled at the same time as the main_clk.
  */
 #define HWMOD_SWSUP_SIDLE			(1 << 0)
 #define HWMOD_SWSUP_MSTANDBY			(1 << 1)
@@ -538,6 +540,7 @@ struct omap_hwmod_omap4_prcm {
 #define HWMOD_FORCE_MSTANDBY			(1 << 11)
 #define HWMOD_SWSUP_SIDLE_ACT			(1 << 12)
 #define HWMOD_RECONFIG_IO_CHAIN			(1 << 13)
+#define HWMOD_OPT_CLKS_NEEDED			(1 << 14)
 
 /*
  * omap_hwmod._int_flags definitions

arch/arm/mach-omap2/omap_hwmod_7xx_data.c

@@ -1297,6 +1297,44 @@ static struct omap_hwmod dra7xx_mcspi4_hwmod = {
 	.dev_attr	= &mcspi4_dev_attr,
 };
 
+/*
+ * 'mcasp' class
+ *
+ */
+static struct omap_hwmod_class_sysconfig dra7xx_mcasp_sysc = {
+	.sysc_offs	= 0x0004,
+	.sysc_flags	= SYSC_HAS_SIDLEMODE,
+	.idlemodes	= (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART),
+	.sysc_fields	= &omap_hwmod_sysc_type3,
+};
+
+static struct omap_hwmod_class dra7xx_mcasp_hwmod_class = {
+	.name	= "mcasp",
+	.sysc	= &dra7xx_mcasp_sysc,
+};
+
+/* mcasp3 */
+static struct omap_hwmod_opt_clk mcasp3_opt_clks[] = {
+	{ .role = "ahclkx", .clk = "mcasp3_ahclkx_mux" },
+};
+
+static struct omap_hwmod dra7xx_mcasp3_hwmod = {
+	.name		= "mcasp3",
+	.class		= &dra7xx_mcasp_hwmod_class,
+	.clkdm_name	= "l4per2_clkdm",
+	.main_clk	= "mcasp3_aux_gfclk_mux",
+	.flags		= HWMOD_OPT_CLKS_NEEDED,
+	.prcm = {
+		.omap4 = {
+			.clkctrl_offs = DRA7XX_CM_L4PER2_MCASP3_CLKCTRL_OFFSET,
+			.context_offs = DRA7XX_RM_L4PER2_MCASP3_CONTEXT_OFFSET,
+			.modulemode   = MODULEMODE_SWCTRL,
+		},
+	},
+	.opt_clks	= mcasp3_opt_clks,
+	.opt_clks_cnt	= ARRAY_SIZE(mcasp3_opt_clks),
+};
+
 /*
  * 'mmc' class
  *
@@ -2566,6 +2604,22 @@ static struct omap_hwmod_ocp_if dra7xx_l3_main_1__hdmi = {
 	.user		= OCP_USER_MPU | OCP_USER_SDMA,
 };
 
+/* l4_per2 -> mcasp3 */
+static struct omap_hwmod_ocp_if dra7xx_l4_per2__mcasp3 = {
+	.master		= &dra7xx_l4_per2_hwmod,
+	.slave		= &dra7xx_mcasp3_hwmod,
+	.clk		= "l4_root_clk_div",
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
+/* l3_main_1 -> mcasp3 */
+static struct omap_hwmod_ocp_if dra7xx_l3_main_1__mcasp3 = {
+	.master		= &dra7xx_l3_main_1_hwmod,
+	.slave		= &dra7xx_mcasp3_hwmod,
+	.clk		= "l3_iclk_div",
+	.user		= OCP_USER_MPU | OCP_USER_SDMA,
+};
+
 /* l4_per1 -> elm */
 static struct omap_hwmod_ocp_if dra7xx_l4_per1__elm = {
 	.master		= &dra7xx_l4_per1_hwmod,
@@ -3308,6 +3362,8 @@ static struct omap_hwmod_ocp_if *dra7xx_hwmod_ocp_ifs[] __initdata = {
 	&dra7xx_l4_wkup__dcan1,
 	&dra7xx_l4_per2__dcan2,
 	&dra7xx_l4_per2__cpgmac0,
+	&dra7xx_l4_per2__mcasp3,
+	&dra7xx_l3_main_1__mcasp3,
 	&dra7xx_gmac__mdio,
 	&dra7xx_l4_cfg__dma_system,
 	&dra7xx_l3_main_1__dss,

arch/arm/mach-omap2/omap_hwmod_81xx_data.c

@@ -144,6 +144,7 @@ static struct omap_hwmod dm81xx_l4_ls_hwmod = {
 	.name		= "l4_ls",
 	.clkdm_name	= "alwon_l3s_clkdm",
 	.class		= &l4_hwmod_class,
+	.flags		= HWMOD_NO_IDLEST,
 };
 
 /*
@@ -155,6 +156,7 @@ static struct omap_hwmod dm81xx_l4_hs_hwmod = {
 	.name		= "l4_hs",
 	.clkdm_name	= "alwon_l3_med_clkdm",
 	.class		= &l4_hwmod_class,
+	.flags		= HWMOD_NO_IDLEST,
 };
 
 /* L3 slow -> L4 ls peripheral interface running at 125MHz */
@@ -850,6 +852,7 @@ static struct omap_hwmod dm816x_emac0_hwmod = {
 	.name		= "emac0",
 	.clkdm_name	= "alwon_ethernet_clkdm",
 	.class		= &dm816x_emac_hwmod_class,
+	.flags		= HWMOD_NO_IDLEST,
 };
 
 static struct omap_hwmod_ocp_if dm81xx_l4_hs__emac0 = {

arch/arm/mach-omap2/pdata-quirks.c

@@ -24,9 +24,6 @@
 #include <linux/platform_data/iommu-omap.h>
 #include <linux/platform_data/wkup_m3.h>
 
-#include <asm/siginfo.h>
-#include <asm/signal.h>
-
 #include "common.h"
 #include "common-board-devices.h"
 #include "dss-common.h"
@@ -385,29 +382,6 @@ static void __init omap3_pandora_legacy_init(void)
 }
 #endif /* CONFIG_ARCH_OMAP3 */
 
-#ifdef CONFIG_SOC_TI81XX
-static int fault_fixed_up;
-
-static int t410_abort_handler(unsigned long addr, unsigned int fsr,
-			      struct pt_regs *regs)
-{
-	if ((fsr == 0x406 || fsr == 0xc06) && !fault_fixed_up) {
-		pr_warn("External imprecise Data abort at addr=%#lx, fsr=%#x ignored.\n",
-			addr, fsr);
-		fault_fixed_up = 1;
-		return 0;
-	}
-
-	return 1;
-}
-
-static void __init t410_abort_init(void)
-{
-	hook_fault_code(16 + 6, t410_abort_handler, SIGBUS, BUS_OBJERR,
-			"imprecise external abort");
-}
-#endif
-
 #if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5)
 static struct iommu_platform_data omap4_iommu_pdata = {
 	.reset_name = "mmu_cache",
@@ -536,9 +510,6 @@ static struct pdata_init pdata_quirks[] __initdata = {
 	{ "openpandora,omap3-pandora-600mhz", omap3_pandora_legacy_init, },
 	{ "openpandora,omap3-pandora-1ghz", omap3_pandora_legacy_init, },
 #endif
-#ifdef CONFIG_SOC_TI81XX
-	{ "hp,t410", t410_abort_init, },
-#endif
 #ifdef CONFIG_SOC_OMAP5
 	{ "ti,omap5-uevm", omap5_uevm_legacy_init, },
 #endif

arch/arm/mach-omap2/pm34xx.c

@@ -301,11 +301,11 @@ static void omap3_pm_idle(void)
 	if (omap_irq_pending())
 		return;
 
-	trace_cpu_idle(1, smp_processor_id());
+	trace_cpu_idle_rcuidle(1, smp_processor_id());
 
 	omap_sram_idle();
 
-	trace_cpu_idle(PWR_EVENT_EXIT, smp_processor_id());
+	trace_cpu_idle_rcuidle(PWR_EVENT_EXIT, smp_processor_id());
 }
 
 #ifdef CONFIG_SUSPEND

arch/arm/mach-orion5x/include/mach/entry-macro.S

@@ -21,5 +21,5 @@
 	@ find cause bits that are unmasked
 	ands	\irqstat, \irqstat, \tmp	@ clear Z flag if any
 	clzne	\irqnr,	\irqstat		@ calc irqnr
-	rsbne	\irqnr, \irqnr, #31
+	rsbne	\irqnr, \irqnr, #32
 	.endm

arch/arm/mach-pxa/palm27x.c

@@ -344,7 +344,7 @@ void __init palm27x_pwm_init(int bl, int lcd)
 {
 	palm_bl_power	= bl;
 	palm_lcd_power	= lcd;
-	pwm_add_lookup(palm27x_pwm_lookup, ARRAY_SIZE(palm27x_pwm_lookup));
+	pwm_add_table(palm27x_pwm_lookup, ARRAY_SIZE(palm27x_pwm_lookup));
 	platform_device_register(&palm27x_backlight);
 }
 #endif

arch/arm/mach-pxa/palmtc.c

@@ -169,7 +169,7 @@ static inline void palmtc_keys_init(void) {}
 #if defined(CONFIG_BACKLIGHT_PWM) || defined(CONFIG_BACKLIGHT_PWM_MODULE)
 static struct pwm_lookup palmtc_pwm_lookup[] = {
 	PWM_LOOKUP("pxa25x-pwm.1", 0, "pwm-backlight.0", NULL, PALMTC_PERIOD_NS,
-		   PWM_PERIOD_NORMAL),
+		   PWM_POLARITY_NORMAL),
 };
 
 static struct platform_pwm_backlight_data palmtc_backlight_data = {

arch/arm/mach-shmobile/setup-r8a7793.c

@@ -19,7 +19,7 @@
 #include "common.h"
 #include "rcar-gen2.h"
 
-static const char *r8a7793_boards_compat_dt[] __initconst = {
+static const char * const r8a7793_boards_compat_dt[] __initconst = {
 	"renesas,r8a7793",
 	NULL,
 };

arch/arm/mach-zx/Kconfig

@@ -13,7 +13,7 @@ config SOC_ZX296702
 	select ARM_GLOBAL_TIMER
 	select HAVE_ARM_SCU if SMP
 	select HAVE_ARM_TWD if SMP
-	select PM_GENERIC_DOMAINS
+	select PM_GENERIC_DOMAINS if PM
 	help
 	  Support for ZTE ZX296702 SoC which is a dual core CortexA9MP
 endif

arch/arm64/Kconfig

@@ -49,7 +49,7 @@ config ARM64
 	select HAVE_ARCH_AUDITSYSCALL
 	select HAVE_ARCH_BITREVERSE
 	select HAVE_ARCH_JUMP_LABEL
-	select HAVE_ARCH_KASAN if SPARSEMEM_VMEMMAP
+	select HAVE_ARCH_KASAN if SPARSEMEM_VMEMMAP && !(ARM64_16K_PAGES && ARM64_VA_BITS_48)
 	select HAVE_ARCH_KGDB
 	select HAVE_ARCH_SECCOMP_FILTER
 	select HAVE_ARCH_TRACEHOOK
@@ -316,6 +316,27 @@ config ARM64_ERRATUM_832075
 
 	  If unsure, say Y.
 
+config ARM64_ERRATUM_834220
+	bool "Cortex-A57: 834220: Stage 2 translation fault might be incorrectly reported in presence of a Stage 1 fault"
+	depends on KVM
+	default y
+	help
+	  This option adds an alternative code sequence to work around ARM
+	  erratum 834220 on Cortex-A57 parts up to r1p2.
+
+	  Affected Cortex-A57 parts might report a Stage 2 translation
+	  fault as the result of a Stage 1 fault for load crossing a
+	  page boundary when there is a permission or device memory
+	  alignment fault at Stage 1 and a translation fault at Stage 2.
+
+	  The workaround is to verify that the Stage 1 translation
+	  doesn't generate a fault before handling the Stage 2 fault.
+	  Please note that this does not necessarily enable the workaround,
+	  as it depends on the alternative framework, which will only patch
+	  the kernel if an affected CPU is detected.
+
+	  If unsure, say Y.
+
 config ARM64_ERRATUM_845719
 	bool "Cortex-A53: 845719: a load might read incorrect data"
 	depends on COMPAT

arch/arm64/crypto/aes-ce-cipher.c

@@ -237,7 +237,7 @@ EXPORT_SYMBOL(ce_aes_setkey);
 static struct crypto_alg aes_alg = {
 	.cra_name		= "aes",
 	.cra_driver_name	= "aes-ce",
-	.cra_priority		= 300,
+	.cra_priority		= 250,
 	.cra_flags		= CRYPTO_ALG_TYPE_CIPHER,
 	.cra_blocksize		= AES_BLOCK_SIZE,
 	.cra_ctxsize		= sizeof(struct crypto_aes_ctx),

arch/arm64/include/asm/barrier.h

@@ -64,27 +64,31 @@ do {									\
 
 #define smp_load_acquire(p)						\
 ({									\
-	typeof(*p) ___p1;						\
+	union { typeof(*p) __val; char __c[1]; } __u;			\
 	compiletime_assert_atomic_type(*p);				\
 	switch (sizeof(*p)) {						\
 	case 1:								\
 		asm volatile ("ldarb %w0, %1"				\
-			: "=r" (___p1) : "Q" (*p) : "memory");		\
+			: "=r" (*(__u8 *)__u.__c)			\
+			: "Q" (*p) : "memory");				\
 		break;							\
 	case 2:								\
 		asm volatile ("ldarh %w0, %1"				\
-			: "=r" (___p1) : "Q" (*p) : "memory");		\
+			: "=r" (*(__u16 *)__u.__c)			\
+			: "Q" (*p) : "memory");				\
 		break;							\
 	case 4:								\
 		asm volatile ("ldar %w0, %1"				\
-			: "=r" (___p1) : "Q" (*p) : "memory");		\
+			: "=r" (*(__u32 *)__u.__c)			\
+			: "Q" (*p) : "memory");				\
 		break;							\
 	case 8:								\
 		asm volatile ("ldar %0, %1"				\
-			: "=r" (___p1) : "Q" (*p) : "memory");		\
+			: "=r" (*(__u64 *)__u.__c)			\
+			: "Q" (*p) : "memory");				\
 		break;							\
 	}								\
-	___p1;								\
+	__u.__val;							\
 })
 
 #define read_barrier_depends()		do { } while(0)

arch/arm64/include/asm/compat.h

@@ -23,7 +23,6 @@
  */
 #include <linux/types.h>
 #include <linux/sched.h>
-#include <linux/ptrace.h>
 
 #define COMPAT_USER_HZ		100
 #ifdef __AARCH64EB__
@@ -234,7 +233,7 @@ static inline compat_uptr_t ptr_to_compat(void __user *uptr)
 	return (u32)(unsigned long)uptr;
 }
 
-#define compat_user_stack_pointer() (user_stack_pointer(current_pt_regs()))
+#define compat_user_stack_pointer() (user_stack_pointer(task_pt_regs(current)))
 
 static inline void __user *arch_compat_alloc_user_space(long len)
 {

arch/arm64/include/asm/cpufeature.h

@@ -29,8 +29,9 @@
 #define ARM64_HAS_PAN				4
 #define ARM64_HAS_LSE_ATOMICS			5
 #define ARM64_WORKAROUND_CAVIUM_23154		6
+#define ARM64_WORKAROUND_834220			7
 
-#define ARM64_NCAPS				7
+#define ARM64_NCAPS				8
 
 #ifndef __ASSEMBLY__
 
@@ -46,8 +47,12 @@ enum ftr_type {
 #define FTR_STRICT	true	/* SANITY check strict matching required */
 #define FTR_NONSTRICT	false	/* SANITY check ignored */
 
+#define FTR_SIGNED	true	/* Value should be treated as signed */
+#define FTR_UNSIGNED	false	/* Value should be treated as unsigned */
+
 struct arm64_ftr_bits {
-	bool		strict;	  /* CPU Sanity check: strict matching required ? */
+	bool		sign;	/* Value is signed ? */
+	bool		strict;	/* CPU Sanity check: strict matching required ? */
 	enum ftr_type	type;
 	u8		shift;
 	u8		width;
@@ -123,6 +128,18 @@ cpuid_feature_extract_field(u64 features, int field)
 	return cpuid_feature_extract_field_width(features, field, 4);
 }
 
+static inline unsigned int __attribute_const__
+cpuid_feature_extract_unsigned_field_width(u64 features, int field, int width)
+{
+	return (u64)(features << (64 - width - field)) >> (64 - width);
+}
+
+static inline unsigned int __attribute_const__
+cpuid_feature_extract_unsigned_field(u64 features, int field)
+{
+	return cpuid_feature_extract_unsigned_field_width(features, field, 4);
+}
+
 static inline u64 arm64_ftr_mask(struct arm64_ftr_bits *ftrp)
 {
 	return (u64)GENMASK(ftrp->shift + ftrp->width - 1, ftrp->shift);
@@ -130,7 +147,9 @@ static inline u64 arm64_ftr_mask(struct arm64_ftr_bits *ftrp)
 
 static inline s64 arm64_ftr_value(struct arm64_ftr_bits *ftrp, u64 val)
 {
-	return cpuid_feature_extract_field_width(val, ftrp->shift, ftrp->width);
+	return ftrp->sign ?
+		cpuid_feature_extract_field_width(val, ftrp->shift, ftrp->width) :
+		cpuid_feature_extract_unsigned_field_width(val, ftrp->shift, ftrp->width);
 }
 
 static inline bool id_aa64mmfr0_mixed_endian_el0(u64 mmfr0)

arch/arm64/include/asm/dma-mapping.h

@@ -18,7 +18,6 @@
 
 #ifdef __KERNEL__
 
-#include <linux/acpi.h>
 #include <linux/types.h>
 #include <linux/vmalloc.h>
 
@@ -26,22 +25,16 @@
 #include <asm/xen/hypervisor.h>
 
 #define DMA_ERROR_CODE	(~(dma_addr_t)0)
-extern struct dma_map_ops *dma_ops;
 extern struct dma_map_ops dummy_dma_ops;
 
 static inline struct dma_map_ops *__generic_dma_ops(struct device *dev)
 {
-	if (unlikely(!dev))
-		return dma_ops;
-	else if (dev->archdata.dma_ops)
+	if (dev && dev->archdata.dma_ops)
 		return dev->archdata.dma_ops;
-	else if (acpi_disabled)
-		return dma_ops;
 
 	/*
-	 * When ACPI is enabled, if arch_set_dma_ops is not called,
-	 * we will disable device DMA capability by setting it
-	 * to dummy_dma_ops.
+	 * We expect no ISA devices, and all other DMA masters are expected to
+	 * have someone call arch_setup_dma_ops at device creation time.
 	 */
 	return &dummy_dma_ops;
 }

arch/arm64/include/asm/hw_breakpoint.h

@@ -138,16 +138,18 @@ extern struct pmu perf_ops_bp;
 /* Determine number of BRP registers available. */
 static inline int get_num_brps(void)
 {
+	u64 dfr0 = read_system_reg(SYS_ID_AA64DFR0_EL1);
 	return 1 +
-		cpuid_feature_extract_field(read_system_reg(SYS_ID_AA64DFR0_EL1),
+		cpuid_feature_extract_unsigned_field(dfr0,
 						ID_AA64DFR0_BRPS_SHIFT);
 }
 
 /* Determine number of WRP registers available. */
 static inline int get_num_wrps(void)
 {
+	u64 dfr0 = read_system_reg(SYS_ID_AA64DFR0_EL1);
 	return 1 +
-		cpuid_feature_extract_field(read_system_reg(SYS_ID_AA64DFR0_EL1),
+		cpuid_feature_extract_unsigned_field(dfr0,
 						ID_AA64DFR0_WRPS_SHIFT);
 }
 

arch/arm64/include/asm/irq.h

@@ -7,4 +7,9 @@ struct pt_regs;
 
 extern void set_handle_irq(void (*handle_irq)(struct pt_regs *));
 
+static inline int nr_legacy_irqs(void)
+{
+	return 0;
+}
+
 #endif

arch/arm64/include/asm/kvm_emulate.h

@@ -99,11 +99,13 @@ static inline void vcpu_set_thumb(struct kvm_vcpu *vcpu)
 	*vcpu_cpsr(vcpu) |= COMPAT_PSR_T_BIT;
 }
 
+/*
+ * vcpu_reg should always be passed a register number coming from a
+ * read of ESR_EL2. Otherwise, it may give the wrong result on AArch32
+ * with banked registers.
+ */
 static inline unsigned long *vcpu_reg(const struct kvm_vcpu *vcpu, u8 reg_num)
 {
-	if (vcpu_mode_is_32bit(vcpu))
-		return vcpu_reg32(vcpu, reg_num);
-
 	return (unsigned long *)&vcpu_gp_regs(vcpu)->regs.regs[reg_num];
 }
 

arch/arm64/include/asm/mmu_context.h

@@ -101,7 +101,7 @@ static inline void cpu_set_default_tcr_t0sz(void)
 #define destroy_context(mm)		do { } while(0)
 void check_and_switch_context(struct mm_struct *mm, unsigned int cpu);
 
-#define init_new_context(tsk,mm)	({ atomic64_set(&mm->context.id, 0); 0; })
+#define init_new_context(tsk,mm)	({ atomic64_set(&(mm)->context.id, 0); 0; })
 
 /*
  * This is called when "tsk" is about to enter lazy TLB mode.

arch/arm64/include/asm/pgtable.h

@@ -81,6 +81,7 @@ extern void __pgd_error(const char *file, int line, unsigned long val);
 
 #define PAGE_KERNEL		__pgprot(_PAGE_DEFAULT | PTE_PXN | PTE_UXN | PTE_DIRTY | PTE_WRITE)
 #define PAGE_KERNEL_RO		__pgprot(_PAGE_DEFAULT | PTE_PXN | PTE_UXN | PTE_DIRTY | PTE_RDONLY)
+#define PAGE_KERNEL_ROX	__pgprot(_PAGE_DEFAULT | PTE_UXN | PTE_DIRTY | PTE_RDONLY)
 #define PAGE_KERNEL_EXEC	__pgprot(_PAGE_DEFAULT | PTE_UXN | PTE_DIRTY | PTE_WRITE)
 #define PAGE_KERNEL_EXEC_CONT	__pgprot(_PAGE_DEFAULT | PTE_UXN | PTE_DIRTY | PTE_WRITE | PTE_CONT)
 

arch/arm64/kernel/cpu_errata.c

@@ -75,6 +75,15 @@ const struct arm64_cpu_capabilities arm64_errata[] = {
 			   (1 << MIDR_VARIANT_SHIFT) | 2),
 	},
 #endif
+#ifdef CONFIG_ARM64_ERRATUM_834220
+	{
+	/* Cortex-A57 r0p0 - r1p2 */
+		.desc = "ARM erratum 834220",
+		.capability = ARM64_WORKAROUND_834220,
+		MIDR_RANGE(MIDR_CORTEX_A57, 0x00,
+			   (1 << MIDR_VARIANT_SHIFT) | 2),
+	},
+#endif
 #ifdef CONFIG_ARM64_ERRATUM_845719
 	{
 	/* Cortex-A53 r0p[01234] */

arch/arm64/kernel/cpufeature.c

@@ -44,8 +44,9 @@ unsigned int compat_elf_hwcap2 __read_mostly;
 
 DECLARE_BITMAP(cpu_hwcaps, ARM64_NCAPS);
 
-#define ARM64_FTR_BITS(STRICT, TYPE, SHIFT, WIDTH, SAFE_VAL) \
+#define __ARM64_FTR_BITS(SIGNED, STRICT, TYPE, SHIFT, WIDTH, SAFE_VAL) \
 	{						\
+		.sign = SIGNED,				\
 		.strict = STRICT,			\
 		.type = TYPE,				\
 		.shift = SHIFT,				\
@@ -53,6 +54,14 @@ DECLARE_BITMAP(cpu_hwcaps, ARM64_NCAPS);
 		.safe_val = SAFE_VAL,			\
 	}
 
+/* Define a feature with signed values */
+#define ARM64_FTR_BITS(STRICT, TYPE, SHIFT, WIDTH, SAFE_VAL) \
+	__ARM64_FTR_BITS(FTR_SIGNED, STRICT, TYPE, SHIFT, WIDTH, SAFE_VAL)
+
+/* Define a feature with unsigned value */
+#define U_ARM64_FTR_BITS(STRICT, TYPE, SHIFT, WIDTH, SAFE_VAL) \
+	__ARM64_FTR_BITS(FTR_UNSIGNED, STRICT, TYPE, SHIFT, WIDTH, SAFE_VAL)
+
 #define ARM64_FTR_END					\
 	{						\
 		.width = 0,				\
@@ -99,7 +108,7 @@ static struct arm64_ftr_bits ftr_id_aa64mmfr0[] = {
 	 * Differing PARange is fine as long as all peripherals and memory are mapped
 	 * within the minimum PARange of all CPUs
 	 */
-	ARM64_FTR_BITS(FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_PARANGE_SHIFT, 4, 0),
+	U_ARM64_FTR_BITS(FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_PARANGE_SHIFT, 4, 0),
 	ARM64_FTR_END,
 };
 
@@ -115,18 +124,18 @@ static struct arm64_ftr_bits ftr_id_aa64mmfr1[] = {
 };
 
 static struct arm64_ftr_bits ftr_ctr[] = {
-	ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, 31, 1, 1),	/* RAO */
+	U_ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, 31, 1, 1),	/* RAO */
 	ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, 28, 3, 0),
-	ARM64_FTR_BITS(FTR_STRICT, FTR_HIGHER_SAFE, 24, 4, 0),	/* CWG */
-	ARM64_FTR_BITS(FTR_STRICT, FTR_LOWER_SAFE, 20, 4, 0),	/* ERG */
-	ARM64_FTR_BITS(FTR_STRICT, FTR_LOWER_SAFE, 16, 4, 1),	/* DminLine */
+	U_ARM64_FTR_BITS(FTR_STRICT, FTR_HIGHER_SAFE, 24, 4, 0),	/* CWG */
+	U_ARM64_FTR_BITS(FTR_STRICT, FTR_LOWER_SAFE, 20, 4, 0),	/* ERG */
+	U_ARM64_FTR_BITS(FTR_STRICT, FTR_LOWER_SAFE, 16, 4, 1),	/* DminLine */
 	/*
 	 * Linux can handle differing I-cache policies. Userspace JITs will
 	 * make use of *minLine
 	 */
-	ARM64_FTR_BITS(FTR_NONSTRICT, FTR_EXACT, 14, 2, 0),	/* L1Ip */
+	U_ARM64_FTR_BITS(FTR_NONSTRICT, FTR_EXACT, 14, 2, 0),	/* L1Ip */
 	ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, 4, 10, 0),	/* RAZ */
-	ARM64_FTR_BITS(FTR_STRICT, FTR_LOWER_SAFE, 0, 4, 0),	/* IminLine */
+	U_ARM64_FTR_BITS(FTR_STRICT, FTR_LOWER_SAFE, 0, 4, 0),	/* IminLine */
 	ARM64_FTR_END,
 };
 
@@ -144,12 +153,12 @@ static struct arm64_ftr_bits ftr_id_mmfr0[] = {
 
 static struct arm64_ftr_bits ftr_id_aa64dfr0[] = {
 	ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, 32, 32, 0),
-	ARM64_FTR_BITS(FTR_STRICT, FTR_LOWER_SAFE, ID_AA64DFR0_CTX_CMPS_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_STRICT, FTR_LOWER_SAFE, ID_AA64DFR0_WRPS_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_STRICT, FTR_LOWER_SAFE, ID_AA64DFR0_BRPS_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, ID_AA64DFR0_PMUVER_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, ID_AA64DFR0_TRACEVER_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, ID_AA64DFR0_DEBUGVER_SHIFT, 4, 0x6),
+	U_ARM64_FTR_BITS(FTR_STRICT, FTR_LOWER_SAFE, ID_AA64DFR0_CTX_CMPS_SHIFT, 4, 0),
+	U_ARM64_FTR_BITS(FTR_STRICT, FTR_LOWER_SAFE, ID_AA64DFR0_WRPS_SHIFT, 4, 0),
+	U_ARM64_FTR_BITS(FTR_STRICT, FTR_LOWER_SAFE, ID_AA64DFR0_BRPS_SHIFT, 4, 0),
+	U_ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, ID_AA64DFR0_PMUVER_SHIFT, 4, 0),
+	U_ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, ID_AA64DFR0_TRACEVER_SHIFT, 4, 0),
+	U_ARM64_FTR_BITS(FTR_STRICT, FTR_EXACT, ID_AA64DFR0_DEBUGVER_SHIFT, 4, 0x6),
 	ARM64_FTR_END,
 };
 

arch/arm64/kernel/cpuinfo.c

@@ -30,6 +30,7 @@
 #include <linux/seq_file.h>
 #include <linux/sched.h>
 #include <linux/smp.h>
+#include <linux/delay.h>
 
 /*
  * In case the boot CPU is hotpluggable, we record its initial state and
@@ -112,6 +113,10 @@ static int c_show(struct seq_file *m, void *v)
 		 */
 		seq_printf(m, "processor\t: %d\n", i);
 
+		seq_printf(m, "BogoMIPS\t: %lu.%02lu\n",
+			   loops_per_jiffy / (500000UL/HZ),
+			   loops_per_jiffy / (5000UL/HZ) % 100);
+
 		/*
 		 * Dump out the common processor features in a single line.
 		 * Userspace should read the hwcaps with getauxval(AT_HWCAP)

arch/arm64/kernel/efi.c

@@ -127,7 +127,11 @@ static int __init uefi_init(void)
 	table_size = sizeof(efi_config_table_64_t) * efi.systab->nr_tables;
 	config_tables = early_memremap(efi_to_phys(efi.systab->tables),
 				       table_size);
-
+	if (config_tables == NULL) {
+		pr_warn("Unable to map EFI config table array.\n");
+		retval = -ENOMEM;
+		goto out;
+	}
 	retval = efi_config_parse_tables(config_tables, efi.systab->nr_tables,
 					 sizeof(efi_config_table_64_t), NULL);
 
@@ -209,6 +213,14 @@ void __init efi_init(void)
 			 PAGE_ALIGN(params.mmap_size + (params.mmap & ~PAGE_MASK)));
 	memmap.phys_map = params.mmap;
 	memmap.map = early_memremap(params.mmap, params.mmap_size);
+	if (memmap.map == NULL) {
+		/*
+		* If we are booting via UEFI, the UEFI memory map is the only
+		* description of memory we have, so there is little point in
+		* proceeding if we cannot access it.
+		*/
+		panic("Unable to map EFI memory map.\n");
+	}
 	memmap.map_end = memmap.map + params.mmap_size;
 	memmap.desc_size = params.desc_size;
 	memmap.desc_version = params.desc_ver;
@@ -224,8 +236,9 @@ static bool __init efi_virtmap_init(void)
 {
 	efi_memory_desc_t *md;
 
+	init_new_context(NULL, &efi_mm);
+
 	for_each_efi_memory_desc(&memmap, md) {
-		u64 paddr, npages, size;
 		pgprot_t prot;
 
 		if (!(md->attribute & EFI_MEMORY_RUNTIME))
@@ -233,11 +246,6 @@ static bool __init efi_virtmap_init(void)
 		if (md->virt_addr == 0)
 			return false;
 
-		paddr = md->phys_addr;
-		npages = md->num_pages;
-		memrange_efi_to_native(&paddr, &npages);
-		size = npages << PAGE_SHIFT;
-
 		pr_info("  EFI remap 0x%016llx => %p\n",
 			md->phys_addr, (void *)md->virt_addr);
 
@@ -254,7 +262,9 @@ static bool __init efi_virtmap_init(void)
 		else
 			prot = PAGE_KERNEL;
 
-		create_pgd_mapping(&efi_mm, paddr, md->virt_addr, size, prot);
+		create_pgd_mapping(&efi_mm, md->phys_addr, md->virt_addr,
+				   md->num_pages << EFI_PAGE_SHIFT, 
+				   __pgprot(pgprot_val(prot) | PTE_NG));
 	}
 	return true;
 }
@@ -270,12 +280,12 @@ static int __init arm64_enable_runtime_services(void)
 
 	if (!efi_enabled(EFI_BOOT)) {
 		pr_info("EFI services will not be available.\n");
-		return -1;
+		return 0;
 	}
 
 	if (efi_runtime_disabled()) {
 		pr_info("EFI runtime services will be disabled.\n");
-		return -1;
+		return 0;
 	}
 
 	pr_info("Remapping and enabling EFI services.\n");
@@ -285,7 +295,7 @@ static int __init arm64_enable_runtime_services(void)
 						   mapsize);
 	if (!memmap.map) {
 		pr_err("Failed to remap EFI memory map\n");
-		return -1;
+		return -ENOMEM;
 	}
 	memmap.map_end = memmap.map + mapsize;
 	efi.memmap = &memmap;
@@ -294,13 +304,13 @@ static int __init arm64_enable_runtime_services(void)
 						   sizeof(efi_system_table_t));
 	if (!efi.systab) {
 		pr_err("Failed to remap EFI System Table\n");
-		return -1;
+		return -ENOMEM;
 	}
 	set_bit(EFI_SYSTEM_TABLES, &efi.flags);
 
 	if (!efi_virtmap_init()) {
 		pr_err("No UEFI virtual mapping was installed -- runtime services will not be available\n");
-		return -1;
+		return -ENOMEM;
 	}
 
 	/* Set up runtime services function pointers */
@@ -329,14 +339,7 @@ core_initcall(arm64_dmi_init);
 
 static void efi_set_pgd(struct mm_struct *mm)
 {
-	if (mm == &init_mm)
-		cpu_set_reserved_ttbr0();
-	else
-		cpu_switch_mm(mm->pgd, mm);
-
-	local_flush_tlb_all();
-	if (icache_is_aivivt())
-		__local_flush_icache_all();
+	switch_mm(NULL, mm, NULL);
 }
 
 void efi_virtmap_load(void)