i2c: designware: add SLAVE mode functions

- Changes in Kconfig to enable I2C_DESIGNWARE_SLAVE support
- Slave functions added to core library file
- Slave abort sources added to common source file
- New driver: i2c-designware-slave added
- Changes in the Makefile to compile the I2C_DESIGNWARE_SLAVE module
  when supported by the architecture.

All the SLAVE flow is added but it is not enabled via platform
driver.

Signed-off-by: Luis Oliveira <lolivei@synopsys.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: made a function static and one-lined a message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

drivers/i2c/busses/Kconfig

@@ -483,14 +483,26 @@ config I2C_DESIGNWARE_CORE
 config I2C_DESIGNWARE_PLATFORM
 	tristate "Synopsys DesignWare Platform"
 	select I2C_DESIGNWARE_CORE
+	select I2C_DESIGNWARE_SLAVE
 	depends on (ACPI && COMMON_CLK) || !ACPI
 	help
 	  If you say yes to this option, support will be included for the
-	  Synopsys DesignWare I2C adapter. Only master mode is supported.
+	  Synopsys DesignWare I2C adapter.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-designware-platform.
 
+config I2C_DESIGNWARE_SLAVE
+	bool "Synopsys DesignWare Slave"
+	select I2C_SLAVE
+	depends on I2C_DESIGNWARE_PLATFORM
+	help
+	  If you say yes to this option, support will be included for the
+	  Synopsys DesignWare I2C slave adapter.
+
+	  This is not a standalone module, this module compiles together with
+	  i2c-designware-core.
+
 config I2C_DESIGNWARE_PCI
 	tristate "Synopsys DesignWare PCI"
 	depends on PCI

drivers/i2c/busses/Makefile

@@ -42,6 +42,9 @@ obj-$(CONFIG_I2C_CPM)		+= i2c-cpm.o
 obj-$(CONFIG_I2C_DAVINCI)	+= i2c-davinci.o
 obj-$(CONFIG_I2C_DESIGNWARE_CORE)	+= i2c-designware-core.o
 i2c-designware-core-objs := i2c-designware-common.o i2c-designware-master.o
+ifeq ($(CONFIG_I2C_DESIGNWARE_SLAVE),y)
+i2c-designware-core-objs += i2c-designware-slave.o
+endif
 obj-$(CONFIG_I2C_DESIGNWARE_PLATFORM)	+= i2c-designware-platform.o
 i2c-designware-platform-objs := i2c-designware-platdrv.o
 i2c-designware-platform-$(CONFIG_I2C_DESIGNWARE_BAYTRAIL) += i2c-designware-baytrail.o

drivers/i2c/busses/i2c-designware-common.c

@@ -56,6 +56,12 @@ static char *abort_sources[] = {
 		"trying to use disabled adapter",
 	[ARB_LOST] =
 		"lost arbitration",
+	[ABRT_SLAVE_FLUSH_TXFIFO] =
+		"read command so flush old data in the TX FIFO",
+	[ABRT_SLAVE_ARBLOST] =
+		"slave lost the bus while transmitting data to a remote master",
+	[ABRT_SLAVE_RD_INTX] =
+		"incorrect slave-transmitter mode configuration",
 };
 
 u32 dw_readl(struct dw_i2c_dev *dev, int offset)

drivers/i2c/busses/i2c-designware-core.h

@@ -305,9 +305,11 @@ u32 i2c_dw_func(struct i2c_adapter *adap);
 void i2c_dw_disable(struct dw_i2c_dev *dev);
 void i2c_dw_disable_int(struct dw_i2c_dev *dev);
 int i2c_dw_init(struct dw_i2c_dev *dev);
+int i2c_dw_init_slave(struct dw_i2c_dev *dev);
 
 extern u32 i2c_dw_read_comp_param(struct dw_i2c_dev *dev);
 extern int i2c_dw_probe(struct dw_i2c_dev *dev);
+extern int i2c_dw_probe_slave(struct dw_i2c_dev *dev);
 
 #if IS_ENABLED(CONFIG_I2C_DESIGNWARE_BAYTRAIL)
 extern int i2c_dw_probe_lock_support(struct dw_i2c_dev *dev);

drivers/i2c/busses/i2c-designware-slave.c

@@ -0,0 +1,394 @@
+/*
+ * Synopsys DesignWare I2C adapter driver (slave only).
+ *
+ * Based on the Synopsys DesignWare I2C adapter driver (master).
+ *
+ * Copyright (C) 2016 Synopsys Inc.
+ *
+ * ----------------------------------------------------------------------------
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ * ----------------------------------------------------------------------------
+ *
+ */
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+
+#include "i2c-designware-core.h"
+
+static void i2c_dw_configure_fifo_slave(struct dw_i2c_dev *dev)
+{
+	/* Configure Tx/Rx FIFO threshold levels. */
+	dw_writel(dev, 0, DW_IC_TX_TL);
+	dw_writel(dev, 0, DW_IC_RX_TL);
+
+	/* Configure the I2C slave. */
+	dw_writel(dev, dev->slave_cfg, DW_IC_CON);
+	dw_writel(dev, DW_IC_INTR_SLAVE_MASK, DW_IC_INTR_MASK);
+}
+
+/**
+ * i2c_dw_init_slave() - Initialize the designware i2c slave hardware
+ * @dev: device private data
+ *
+ * This function configures and enables the I2C in slave mode.
+ * This function is called during I2C init function, and in case of timeout at
+ * run time.
+ */
+int i2c_dw_init_slave(struct dw_i2c_dev *dev)
+{
+	u32 sda_falling_time, scl_falling_time;
+	u32 reg, comp_param1;
+	u32 hcnt, lcnt;
+	int ret;
+
+	ret = i2c_dw_acquire_lock(dev);
+	if (ret)
+		return ret;
+
+	reg = dw_readl(dev, DW_IC_COMP_TYPE);
+	if (reg == ___constant_swab32(DW_IC_COMP_TYPE_VALUE)) {
+		/* Configure register endianness access. */
+		dev->flags |= ACCESS_SWAP;
+	} else if (reg == (DW_IC_COMP_TYPE_VALUE & 0x0000ffff)) {
+		/* Configure register access mode 16bit. */
+		dev->flags |= ACCESS_16BIT;
+	} else if (reg != DW_IC_COMP_TYPE_VALUE) {
+		dev_err(dev->dev,
+			"Unknown Synopsys component type: 0x%08x\n", reg);
+		i2c_dw_release_lock(dev);
+		return -ENODEV;
+	}
+
+	comp_param1 = dw_readl(dev, DW_IC_COMP_PARAM_1);
+
+	/* Disable the adapter. */
+	__i2c_dw_enable_and_wait(dev, false);
+
+	/* Set standard and fast speed deviders for high/low periods. */
+	sda_falling_time = dev->sda_falling_time ?: 300; /* ns */
+	scl_falling_time = dev->scl_falling_time ?: 300; /* ns */
+
+	/* Set SCL timing parameters for standard-mode. */
+	if (dev->ss_hcnt && dev->ss_lcnt) {
+		hcnt = dev->ss_hcnt;
+		lcnt = dev->ss_lcnt;
+	} else {
+		hcnt = i2c_dw_scl_hcnt(i2c_dw_clk_rate(dev),
+				       4000,	/* tHD;STA = tHIGH = 4.0 us */
+				       sda_falling_time,
+				       0,	/* 0: DW default, 1: Ideal */
+				       0);	/* No offset */
+		lcnt = i2c_dw_scl_lcnt(i2c_dw_clk_rate(dev),
+				       4700,	/* tLOW = 4.7 us */
+				       scl_falling_time,
+				       0);	/* No offset */
+	}
+	dw_writel(dev, hcnt, DW_IC_SS_SCL_HCNT);
+	dw_writel(dev, lcnt, DW_IC_SS_SCL_LCNT);
+	dev_dbg(dev->dev, "Standard-mode HCNT:LCNT = %d:%d\n", hcnt, lcnt);
+
+	/* Set SCL timing parameters for fast-mode or fast-mode plus. */
+	if ((dev->clk_freq == 1000000) && dev->fp_hcnt && dev->fp_lcnt) {
+		hcnt = dev->fp_hcnt;
+		lcnt = dev->fp_lcnt;
+	} else if (dev->fs_hcnt && dev->fs_lcnt) {
+		hcnt = dev->fs_hcnt;
+		lcnt = dev->fs_lcnt;
+	} else {
+		hcnt = i2c_dw_scl_hcnt(i2c_dw_clk_rate(dev),
+				       600,	/* tHD;STA = tHIGH = 0.6 us */
+				       sda_falling_time,
+				       0,	/* 0: DW default, 1: Ideal */
+				       0);	/* No offset */
+		lcnt = i2c_dw_scl_lcnt(i2c_dw_clk_rate(dev),
+				       1300,	/* tLOW = 1.3 us */
+				       scl_falling_time,
+				       0);	/* No offset */
+	}
+	dw_writel(dev, hcnt, DW_IC_FS_SCL_HCNT);
+	dw_writel(dev, lcnt, DW_IC_FS_SCL_LCNT);
+	dev_dbg(dev->dev, "Fast-mode HCNT:LCNT = %d:%d\n", hcnt, lcnt);
+
+	if ((dev->slave_cfg & DW_IC_CON_SPEED_MASK) ==
+		DW_IC_CON_SPEED_HIGH) {
+		if ((comp_param1 & DW_IC_COMP_PARAM_1_SPEED_MODE_MASK)
+			!= DW_IC_COMP_PARAM_1_SPEED_MODE_HIGH) {
+			dev_err(dev->dev, "High Speed not supported!\n");
+			dev->slave_cfg &= ~DW_IC_CON_SPEED_MASK;
+			dev->slave_cfg |= DW_IC_CON_SPEED_FAST;
+		} else if (dev->hs_hcnt && dev->hs_lcnt) {
+			hcnt = dev->hs_hcnt;
+			lcnt = dev->hs_lcnt;
+			dw_writel(dev, hcnt, DW_IC_HS_SCL_HCNT);
+			dw_writel(dev, lcnt, DW_IC_HS_SCL_LCNT);
+			dev_dbg(dev->dev, "HighSpeed-mode HCNT:LCNT = %d:%d\n",
+				hcnt, lcnt);
+		}
+	}
+
+	/* Configure SDA Hold Time if required. */
+	reg = dw_readl(dev, DW_IC_COMP_VERSION);
+	if (reg >= DW_IC_SDA_HOLD_MIN_VERS) {
+		if (!dev->sda_hold_time) {
+			/* Keep previous hold time setting if no one set it. */
+			dev->sda_hold_time = dw_readl(dev, DW_IC_SDA_HOLD);
+		}
+		/*
+		 * Workaround for avoiding TX arbitration lost in case I2C
+		 * slave pulls SDA down "too quickly" after falling egde of
+		 * SCL by enabling non-zero SDA RX hold. Specification says it
+		 * extends incoming SDA low to high transition while SCL is
+		 * high but it apprears to help also above issue.
+		 */
+		if (!(dev->sda_hold_time & DW_IC_SDA_HOLD_RX_MASK))
+			dev->sda_hold_time |= 1 << DW_IC_SDA_HOLD_RX_SHIFT;
+		dw_writel(dev, dev->sda_hold_time, DW_IC_SDA_HOLD);
+	} else {
+		dev_warn(dev->dev,
+			 "Hardware too old to adjust SDA hold time.\n");
+	}
+
+	i2c_dw_configure_fifo_slave(dev);
+	i2c_dw_release_lock(dev);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(i2c_dw_init_slave);
+
+static int i2c_dw_reg_slave(struct i2c_client *slave)
+{
+	struct dw_i2c_dev *dev = i2c_get_adapdata(slave->adapter);
+
+	if (dev->slave)
+		return -EBUSY;
+	if (slave->flags & I2C_CLIENT_TEN)
+		return -EAFNOSUPPORT;
+	/*
+	 * Set slave address in the IC_SAR register,
+	 * the address to which the DW_apb_i2c responds.
+	 */
+	__i2c_dw_enable(dev, false);
+	dw_writel(dev, slave->addr, DW_IC_SAR);
+	dev->slave = slave;
+
+	__i2c_dw_enable(dev, true);
+
+	dev->cmd_err = 0;
+	dev->msg_write_idx = 0;
+	dev->msg_read_idx = 0;
+	dev->msg_err = 0;
+	dev->status = STATUS_IDLE;
+	dev->abort_source = 0;
+	dev->rx_outstanding = 0;
+
+	return 0;
+}
+
+static int i2c_dw_unreg_slave(struct i2c_client *slave)
+{
+	struct dw_i2c_dev *dev = i2c_get_adapdata(slave->adapter);
+
+	dev->disable_int(dev);
+	dev->disable(dev);
+	dev->slave = NULL;
+
+	return 0;
+}
+
+static u32 i2c_dw_read_clear_intrbits_slave(struct dw_i2c_dev *dev)
+{
+	u32 stat;
+
+	/*
+	 * The IC_INTR_STAT register just indicates "enabled" interrupts.
+	 * Ths unmasked raw version of interrupt status bits are available
+	 * in the IC_RAW_INTR_STAT register.
+	 *
+	 * That is,
+	 *   stat = dw_readl(IC_INTR_STAT);
+	 * equals to,
+	 *   stat = dw_readl(IC_RAW_INTR_STAT) & dw_readl(IC_INTR_MASK);
+	 *
+	 * The raw version might be useful for debugging purposes.
+	 */
+	stat = dw_readl(dev, DW_IC_INTR_STAT);
+
+	/*
+	 * Do not use the IC_CLR_INTR register to clear interrupts, or
+	 * you'll miss some interrupts, triggered during the period from
+	 * dw_readl(IC_INTR_STAT) to dw_readl(IC_CLR_INTR).
+	 *
+	 * Instead, use the separately-prepared IC_CLR_* registers.
+	 */
+	if (stat & DW_IC_INTR_TX_ABRT)
+		dw_readl(dev, DW_IC_CLR_TX_ABRT);
+	if (stat & DW_IC_INTR_RX_UNDER)
+		dw_readl(dev, DW_IC_CLR_RX_UNDER);
+	if (stat & DW_IC_INTR_RX_OVER)
+		dw_readl(dev, DW_IC_CLR_RX_OVER);
+	if (stat & DW_IC_INTR_TX_OVER)
+		dw_readl(dev, DW_IC_CLR_TX_OVER);
+	if (stat & DW_IC_INTR_RX_DONE)
+		dw_readl(dev, DW_IC_CLR_RX_DONE);
+	if (stat & DW_IC_INTR_ACTIVITY)
+		dw_readl(dev, DW_IC_CLR_ACTIVITY);
+	if (stat & DW_IC_INTR_STOP_DET)
+		dw_readl(dev, DW_IC_CLR_STOP_DET);
+	if (stat & DW_IC_INTR_START_DET)
+		dw_readl(dev, DW_IC_CLR_START_DET);
+	if (stat & DW_IC_INTR_GEN_CALL)
+		dw_readl(dev, DW_IC_CLR_GEN_CALL);
+
+	return stat;
+}
+
+/*
+ * Interrupt service routine. This gets called whenever an I2C slave interrupt
+ * occurs.
+ */
+
+static int i2c_dw_irq_handler_slave(struct dw_i2c_dev *dev)
+{
+	u32 raw_stat, stat, enabled;
+	u8 val, slave_activity;
+
+	stat = dw_readl(dev, DW_IC_INTR_STAT);
+	enabled = dw_readl(dev, DW_IC_ENABLE);
+	raw_stat = dw_readl(dev, DW_IC_RAW_INTR_STAT);
+	slave_activity = ((dw_readl(dev, DW_IC_STATUS) &
+		DW_IC_STATUS_SLAVE_ACTIVITY) >> 6);
+
+	if (!enabled || !(raw_stat & ~DW_IC_INTR_ACTIVITY))
+		return 0;
+
+	dev_dbg(dev->dev,
+		"%#x STAUTS SLAVE_ACTTVITY=%#x : RAW_INTR_STAT=%#x : INTR_STAT=%#x\n",
+		enabled, slave_activity, raw_stat, stat);
+
+	if ((stat & DW_IC_INTR_RX_FULL) && (stat & DW_IC_INTR_STOP_DET))
+		i2c_slave_event(dev->slave, I2C_SLAVE_WRITE_REQUESTED, &val);
+
+	if (stat & DW_IC_INTR_RD_REQ) {
+		if (slave_activity) {
+			if (stat & DW_IC_INTR_RX_FULL) {
+				val = dw_readl(dev, DW_IC_DATA_CMD);
+
+				if (!i2c_slave_event(dev->slave,
+						     I2C_SLAVE_WRITE_RECEIVED,
+						     &val)) {
+					dev_vdbg(dev->dev, "Byte %X acked!",
+						 val);
+				}
+				dw_readl(dev, DW_IC_CLR_RD_REQ);
+				stat = i2c_dw_read_clear_intrbits_slave(dev);
+			} else {
+				dw_readl(dev, DW_IC_CLR_RD_REQ);
+				dw_readl(dev, DW_IC_CLR_RX_UNDER);
+				stat = i2c_dw_read_clear_intrbits_slave(dev);
+			}
+			if (!i2c_slave_event(dev->slave,
+					     I2C_SLAVE_READ_REQUESTED,
+					     &val))
+				dw_writel(dev, val, DW_IC_DATA_CMD);
+		}
+	}
+
+	if (stat & DW_IC_INTR_RX_DONE) {
+		if (!i2c_slave_event(dev->slave, I2C_SLAVE_READ_PROCESSED,
+				     &val))
+			dw_readl(dev, DW_IC_CLR_RX_DONE);
+
+		i2c_slave_event(dev->slave, I2C_SLAVE_STOP, &val);
+		stat = i2c_dw_read_clear_intrbits_slave(dev);
+		return 1;
+	}
+
+	if (stat & DW_IC_INTR_RX_FULL) {
+		val = dw_readl(dev, DW_IC_DATA_CMD);
+		if (!i2c_slave_event(dev->slave, I2C_SLAVE_WRITE_RECEIVED,
+				     &val))
+			dev_vdbg(dev->dev, "Byte %X acked!", val);
+	} else {
+		i2c_slave_event(dev->slave, I2C_SLAVE_STOP, &val);
+		stat = i2c_dw_read_clear_intrbits_slave(dev);
+	}
+
+	return 1;
+}
+
+static irqreturn_t i2c_dw_isr_slave(int this_irq, void *dev_id)
+{
+	struct dw_i2c_dev *dev = dev_id;
+	int ret;
+
+	i2c_dw_read_clear_intrbits_slave(dev);
+	ret = i2c_dw_irq_handler_slave(dev);
+	if (ret > 0)
+		complete(&dev->cmd_complete);
+
+	return IRQ_RETVAL(ret);
+}
+
+static struct i2c_algorithm i2c_dw_algo = {
+	.functionality = i2c_dw_func,
+	.reg_slave = i2c_dw_reg_slave,
+	.unreg_slave = i2c_dw_unreg_slave,
+};
+
+int i2c_dw_probe_slave(struct dw_i2c_dev *dev)
+{
+	struct i2c_adapter *adap = &dev->adapter;
+	int ret;
+
+	init_completion(&dev->cmd_complete);
+
+	dev->init = i2c_dw_init_slave;
+	dev->disable = i2c_dw_disable;
+	dev->disable_int = i2c_dw_disable_int;
+
+	ret = dev->init(dev);
+	if (ret)
+		return ret;
+
+	snprintf(adap->name, sizeof(adap->name),
+		 "Synopsys DesignWare I2C Slave adapter");
+	adap->retries = 3;
+	adap->algo = &i2c_dw_algo;
+	adap->dev.parent = dev->dev;
+	i2c_set_adapdata(adap, dev);
+
+	ret = devm_request_irq(dev->dev, dev->irq, i2c_dw_isr_slave,
+			       IRQF_SHARED, dev_name(dev->dev), dev);
+	if (ret) {
+		dev_err(dev->dev, "failure requesting irq %i: %d\n",
+			dev->irq, ret);
+		return ret;
+	}
+
+	ret = i2c_add_numbered_adapter(adap);
+	if (ret)
+		dev_err(dev->dev, "failure adding adapter: %d\n", ret);
+	pm_runtime_put_noidle(dev->dev);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(i2c_dw_probe_slave);
+
+MODULE_AUTHOR("Luis Oliveira <lolivei@synopsys.com>");
+MODULE_DESCRIPTION("Synopsys DesignWare I2C bus slave adapter");
+MODULE_LICENSE("GPL v2");