USB: serial: mos7840.c: remove dbg() usage

dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.

CC: Johan Hovold <jhovold@gmail.com>
CC: Mark Ferrell <mferrell@uplogix.com>
CC: Donald Lee <donald@asix.com.tw>
CC: Tony Zelenoff <antonz@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/serial/mos7840.c

@@ -265,7 +265,7 @@ static int mos7840_set_reg_sync(struct usb_serial_port *port, __u16 reg,
 {
 	struct usb_device *dev = port->serial->dev;
 	val = val & 0x00ff;
-	dbg("mos7840_set_reg_sync offset is %x, value %x", reg, val);
+	dev_dbg(&port->dev, "mos7840_set_reg_sync offset is %x, value %x\n", reg, val);
 
 	return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), MCS_WRREQ,
 			       MCS_WR_RTYPE, val, reg, NULL, 0,
@@ -293,7 +293,7 @@ static int mos7840_get_reg_sync(struct usb_serial_port *port, __u16 reg,
 			      MCS_RD_RTYPE, 0, reg, buf, VENDOR_READ_LENGTH,
 			      MOS_WDR_TIMEOUT);
 	*val = buf[0];
-	dbg("mos7840_get_reg_sync offset is %x, return val %x", reg, *val);
+	dev_dbg(&port->dev, "%s offset is %x, return val %x\n", __func__, reg, *val);
 
 	kfree(buf);
 	return ret;
@@ -316,21 +316,16 @@ static int mos7840_set_uart_reg(struct usb_serial_port *port, __u16 reg,
 	if (port->serial->num_ports == 4) {
 		val |= (((__u16) port->number -
 				(__u16) (port->serial->minor)) + 1) << 8;
-		dbg("mos7840_set_uart_reg application number is %x", val);
 	} else {
 		if (((__u16) port->number - (__u16) (port->serial->minor)) == 0) {
 			val |= (((__u16) port->number -
 			      (__u16) (port->serial->minor)) + 1) << 8;
-			dbg("mos7840_set_uart_reg application number is %x",
-			    val);
 		} else {
-			val |=
-			    (((__u16) port->number -
+			val |= (((__u16) port->number -
 			      (__u16) (port->serial->minor)) + 2) << 8;
-			dbg("mos7840_set_uart_reg application number is %x",
-			    val);
 		}
 	}
+	dev_dbg(&port->dev, "%s application number is %x\n", __func__, val);
 	return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), MCS_WRREQ,
 			       MCS_WR_RTYPE, val, reg, NULL, 0,
 			       MOS_WDR_TIMEOUT);
@@ -354,27 +349,21 @@ static int mos7840_get_uart_reg(struct usb_serial_port *port, __u16 reg,
 	if (!buf)
 		return -ENOMEM;
 
-	/* dbg("application number is %4x",
-	    (((__u16)port->number - (__u16)(port->serial->minor))+1)<<8); */
 	/* Wval  is same as application number */
 	if (port->serial->num_ports == 4) {
 		Wval =
 		    (((__u16) port->number - (__u16) (port->serial->minor)) +
 		     1) << 8;
-		dbg("mos7840_get_uart_reg application number is %x", Wval);
 	} else {
 		if (((__u16) port->number - (__u16) (port->serial->minor)) == 0) {
 			Wval = (((__u16) port->number -
 			      (__u16) (port->serial->minor)) + 1) << 8;
-			dbg("mos7840_get_uart_reg application number is %x",
-			    Wval);
 		} else {
 			Wval = (((__u16) port->number -
 			      (__u16) (port->serial->minor)) + 2) << 8;
-			dbg("mos7840_get_uart_reg application number is %x",
-			    Wval);
 		}
 	}
+	dev_dbg(&port->dev, "%s application number is %x\n", __func__, Wval);
 	ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), MCS_RDREQ,
 			      MCS_RD_RTYPE, Wval, reg, buf, VENDOR_READ_LENGTH,
 			      MOS_WDR_TIMEOUT);
@@ -384,14 +373,13 @@ static int mos7840_get_uart_reg(struct usb_serial_port *port, __u16 reg,
 	return ret;
 }
 
-static void mos7840_dump_serial_port(struct moschip_port *mos7840_port)
+static void mos7840_dump_serial_port(struct usb_serial_port *port,
+				     struct moschip_port *mos7840_port)
 {
 
-	dbg("***************************************");
-	dbg("SpRegOffset is %2x", mos7840_port->SpRegOffset);
-	dbg("ControlRegOffset is %2x", mos7840_port->ControlRegOffset);
-	dbg("DCRRegOffset is %2x", mos7840_port->DcrRegOffset);
-	dbg("***************************************");
+	dev_dbg(&port->dev, "SpRegOffset is %2x\n", mos7840_port->SpRegOffset);
+	dev_dbg(&port->dev, "ControlRegOffset is %2x\n", mos7840_port->ControlRegOffset);
+	dev_dbg(&port->dev, "DCRRegOffset is %2x\n", mos7840_port->DcrRegOffset);
 
 }
 
@@ -450,8 +438,6 @@ static void mos7840_handle_new_lsr(struct moschip_port *port, __u8 new_lsr)
 {
 	struct async_icount *icount;
 
-	dbg("%s - %02x", __func__, new_lsr);
-
 	if (new_lsr & SERIAL_LSR_BI) {
 		/*
 		 * Parity and Framing errors only count if they
@@ -492,6 +478,7 @@ static void mos7840_control_callback(struct urb *urb)
 {
 	unsigned char *data;
 	struct moschip_port *mos7840_port;
+	struct device *dev = &urb->dev->dev;
 	__u8 regval = 0x0;
 	int result = 0;
 	int status = urb->status;
@@ -506,21 +493,19 @@ static void mos7840_control_callback(struct urb *urb)
 	case -ENOENT:
 	case -ESHUTDOWN:
 		/* this urb is terminated, clean up */
-		dbg("%s - urb shutting down with status: %d", __func__,
-		    status);
+		dev_dbg(dev, "%s - urb shutting down with status: %d\n", __func__, status);
 		return;
 	default:
-		dbg("%s - nonzero urb status received: %d", __func__,
-		    status);
+		dev_dbg(dev, "%s - nonzero urb status received: %d\n", __func__, status);
 		goto exit;
 	}
 
-	dbg("%s urb buffer size is %d", __func__, urb->actual_length);
-	dbg("%s mos7840_port->MsrLsr is %d port %d", __func__,
-	    mos7840_port->MsrLsr, mos7840_port->port_num);
+	dev_dbg(dev, "%s urb buffer size is %d\n", __func__, urb->actual_length);
+	dev_dbg(dev, "%s mos7840_port->MsrLsr is %d port %d\n", __func__,
+		mos7840_port->MsrLsr, mos7840_port->port_num);
 	data = urb->transfer_buffer;
 	regval = (__u8) data[0];
-	dbg("%s data is %x", __func__, regval);
+	dev_dbg(dev, "%s data is %x\n", __func__, regval);
 	if (mos7840_port->MsrLsr == 0)
 		mos7840_handle_new_msr(mos7840_port, regval);
 	else if (mos7840_port->MsrLsr == 1)
@@ -532,8 +517,7 @@ exit:
 		result = usb_submit_urb(mos7840_port->int_urb, GFP_ATOMIC);
 	spin_unlock(&mos7840_port->pool_lock);
 	if (result) {
-		dev_err(&urb->dev->dev,
-			"%s - Error %d submitting interrupt urb\n",
+		dev_err(dev, "%s - Error %d submitting interrupt urb\n",
 			__func__, result);
 	}
 }
@@ -570,12 +554,12 @@ static void mos7840_set_led_callback(struct urb *urb)
 	case -ENOENT:
 	case -ESHUTDOWN:
 		/* This urb is terminated, clean up */
-		dbg("%s - urb shutting down with status: %d", __func__,
-			urb->status);
+		dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d",
+			__func__, urb->status);
 		break;
 	default:
-		dbg("%s - nonzero urb status received: %d", __func__,
-			urb->status);
+		dev_dbg(&urb->dev->dev, "%s - nonzero urb status received: %d",
+			__func__, urb->status);
 	}
 }
 
@@ -650,12 +634,12 @@ static void mos7840_interrupt_callback(struct urb *urb)
 	case -ENOENT:
 	case -ESHUTDOWN:
 		/* this urb is terminated, clean up */
-		dbg("%s - urb shutting down with status: %d", __func__,
-		    status);
+		dev_dbg(&urb->dev->dev, "%s - urb shutting down with status: %d\n",
+			__func__, status);
 		return;
 	default:
-		dbg("%s - nonzero urb status received: %d", __func__,
-		    status);
+		dev_dbg(&urb->dev->dev, "%s - nonzero urb status received: %d\n",
+			__func__, status);
 		goto exit;
 	}
 
@@ -672,7 +656,7 @@ static void mos7840_interrupt_callback(struct urb *urb)
 	 * Byte 5 FIFO status for both */
 
 	if (length && length > 5) {
-		dbg("%s", "Wrong data !!!");
+		dev_dbg(&urb->dev->dev, "%s", "Wrong data !!!\n");
 		return;
 	}
 
@@ -689,17 +673,17 @@ static void mos7840_interrupt_callback(struct urb *urb)
 		      (__u16) (serial->minor)) + 1) << 8;
 		if (mos7840_port->open) {
 			if (sp[i] & 0x01) {
-				dbg("SP%d No Interrupt !!!", i);
+				dev_dbg(&urb->dev->dev, "SP%d No Interrupt !!!\n", i);
 			} else {
 				switch (sp[i] & 0x0f) {
 				case SERIAL_IIR_RLS:
-					dbg("Serial Port %d: Receiver status error or ", i);
-					dbg("address bit detected in 9-bit mode");
+					dev_dbg(&urb->dev->dev, "Serial Port %d: Receiver status error or \n", i);
+					dev_dbg(&urb->dev->dev, "address bit detected in 9-bit mode\n");
 					mos7840_port->MsrLsr = 1;
 					wreg = LINE_STATUS_REGISTER;
 					break;
 				case SERIAL_IIR_MS:
-					dbg("Serial Port %d: Modem status change", i);
+					dev_dbg(&urb->dev->dev, "Serial Port %d: Modem status change\n", i);
 					mos7840_port->MsrLsr = 0;
 					wreg = MODEM_STATUS_REGISTER;
 					break;
@@ -731,11 +715,11 @@ static int mos7840_port_paranoia_check(struct usb_serial_port *port,
 				       const char *function)
 {
 	if (!port) {
-		dbg("%s - port == NULL", function);
+		pr_debug("%s - port == NULL\n", function);
 		return -1;
 	}
 	if (!port->serial) {
-		dbg("%s - port->serial == NULL", function);
+		pr_debug("%s - port->serial == NULL\n", function);
 		return -1;
 	}
 
@@ -747,11 +731,11 @@ static int mos7840_serial_paranoia_check(struct usb_serial *serial,
 					 const char *function)
 {
 	if (!serial) {
-		dbg("%s - serial == NULL", function);
+		pr_debug("%s - serial == NULL\n", function);
 		return -1;
 	}
 	if (!serial->type) {
-		dbg("%s - serial->type == NULL!", function);
+		pr_debug("%s - serial->type == NULL!\n", function);
 		return -1;
 	}
 
@@ -790,49 +774,44 @@ static void mos7840_bulk_in_callback(struct urb *urb)
 	int status = urb->status;
 
 	mos7840_port = urb->context;
-	if (!mos7840_port) {
-		dbg("%s", "NULL mos7840_port pointer");
+	if (!mos7840_port)
 		return;
-	}
 
 	if (status) {
-		dbg("nonzero read bulk status received: %d", status);
+		dev_dbg(&urb->dev->dev, "nonzero read bulk status received: %d\n", status);
 		mos7840_port->read_urb_busy = false;
 		return;
 	}
 
-	port = (struct usb_serial_port *)mos7840_port->port;
+	port = mos7840_port->port;
 	if (mos7840_port_paranoia_check(port, __func__)) {
-		dbg("%s", "Port Paranoia failed");
 		mos7840_port->read_urb_busy = false;
 		return;
 	}
 
 	serial = mos7840_get_usb_serial(port, __func__);
 	if (!serial) {
-		dbg("%s", "Bad serial pointer");
 		mos7840_port->read_urb_busy = false;
 		return;
 	}
 
 	data = urb->transfer_buffer;
+	usb_serial_debug_data(debug, &port->dev, __func__, urb->actual_length, data);
 
 	if (urb->actual_length) {
 		tty = tty_port_tty_get(&mos7840_port->port->port);
 		if (tty) {
 			tty_insert_flip_string(tty, data, urb->actual_length);
-			dbg(" %s ", data);
 			tty_flip_buffer_push(tty);
 			tty_kref_put(tty);
 		}
 		mos7840_port->icount.rx += urb->actual_length;
 		smp_wmb();
-		dbg("mos7840_port->icount.rx is %d:",
-		    mos7840_port->icount.rx);
+		dev_dbg(&port->dev, "mos7840_port->icount.rx is %d:\n", mos7840_port->icount.rx);
 	}
 
 	if (!mos7840_port->read_urb) {
-		dbg("%s", "URB KILLED !!!");
+		dev_dbg(&port->dev, "%s", "URB KILLED !!!\n");
 		mos7840_port->read_urb_busy = false;
 		return;
 	}
@@ -850,7 +829,7 @@ static void mos7840_bulk_in_callback(struct urb *urb)
 	retval = usb_submit_urb(mos7840_port->read_urb, GFP_ATOMIC);
 
 	if (retval) {
-		dbg("usb_submit_urb(read bulk) failed, retval = %d", retval);
+		dev_dbg(&port->dev, "usb_submit_urb(read bulk) failed, retval = %d\n", retval);
 		mos7840_port->read_urb_busy = false;
 	}
 }
@@ -864,11 +843,13 @@ static void mos7840_bulk_in_callback(struct urb *urb)
 static void mos7840_bulk_out_data_callback(struct urb *urb)
 {
 	struct moschip_port *mos7840_port;
+	struct usb_serial_port *port;
 	struct tty_struct *tty;
 	int status = urb->status;
 	int i;
 
 	mos7840_port = urb->context;
+	port = mos7840_port->port;
 	spin_lock(&mos7840_port->pool_lock);
 	for (i = 0; i < NUM_URBS; i++) {
 		if (urb == mos7840_port->write_urb_pool[i]) {
@@ -879,16 +860,14 @@ static void mos7840_bulk_out_data_callback(struct urb *urb)
 	spin_unlock(&mos7840_port->pool_lock);
 
 	if (status) {
-		dbg("nonzero write bulk status received:%d", status);
+		dev_dbg(&port->dev, "nonzero write bulk status received:%d\n", status);
 		return;
 	}
 
-	if (mos7840_port_paranoia_check(mos7840_port->port, __func__)) {
-		dbg("%s", "Port Paranoia failed");
+	if (mos7840_port_paranoia_check(port, __func__))
 		return;
-	}
 
-	tty = tty_port_tty_get(&mos7840_port->port->port);
+	tty = tty_port_tty_get(&port->port);
 	if (tty && mos7840_port->open)
 		tty_wakeup(tty);
 	tty_kref_put(tty);
@@ -929,17 +908,13 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port)
 	struct moschip_port *mos7840_port;
 	struct moschip_port *port0;
 
-	if (mos7840_port_paranoia_check(port, __func__)) {
-		dbg("%s", "Port Paranoia failed");
+	if (mos7840_port_paranoia_check(port, __func__))
 		return -ENODEV;
-	}
 
 	serial = port->serial;
 
-	if (mos7840_serial_paranoia_check(serial, __func__)) {
-		dbg("%s", "Serial Paranoia failed");
+	if (mos7840_serial_paranoia_check(serial, __func__))
 		return -ENODEV;
-	}
 
 	mos7840_port = mos7840_get_port_private(port);
 	port0 = mos7840_get_port_private(serial->port[0]);
@@ -990,20 +965,20 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port)
 	Data = 0x0;
 	status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset, &Data);
 	if (status < 0) {
-		dbg("Reading Spreg failed");
+		dev_dbg(&port->dev, "Reading Spreg failed\n");
 		return -1;
 	}
 	Data |= 0x80;
 	status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data);
 	if (status < 0) {
-		dbg("writing Spreg failed");
+		dev_dbg(&port->dev, "writing Spreg failed\n");
 		return -1;
 	}
 
 	Data &= ~0x80;
 	status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset, Data);
 	if (status < 0) {
-		dbg("writing Spreg failed");
+		dev_dbg(&port->dev, "writing Spreg failed\n");
 		return -1;
 	}
 	/* End of block to be checked */
@@ -1012,7 +987,7 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port)
 	status = mos7840_get_reg_sync(port, mos7840_port->ControlRegOffset,
 									&Data);
 	if (status < 0) {
-		dbg("Reading Controlreg failed");
+		dev_dbg(&port->dev, "Reading Controlreg failed\n");
 		return -1;
 	}
 	Data |= 0x08;		/* Driver done bit */
@@ -1020,7 +995,7 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port)
 	status = mos7840_set_reg_sync(port,
 				mos7840_port->ControlRegOffset, Data);
 	if (status < 0) {
-		dbg("writing Controlreg failed");
+		dev_dbg(&port->dev, "writing Controlreg failed\n");
 		return -1;
 	}
 	/* do register settings here */
@@ -1031,21 +1006,21 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port)
 	Data = 0x00;
 	status = mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
 	if (status < 0) {
-		dbg("disabling interrupts failed");
+		dev_dbg(&port->dev, "disabling interrupts failed\n");
 		return -1;
 	}
 	/* Set FIFO_CONTROL_REGISTER to the default value */
 	Data = 0x00;
 	status = mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
 	if (status < 0) {
-		dbg("Writing FIFO_CONTROL_REGISTER  failed");
+		dev_dbg(&port->dev, "Writing FIFO_CONTROL_REGISTER  failed\n");
 		return -1;
 	}
 
 	Data = 0xcf;
 	status = mos7840_set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
 	if (status < 0) {
-		dbg("Writing FIFO_CONTROL_REGISTER  failed");
+		dev_dbg(&port->dev, "Writing FIFO_CONTROL_REGISTER  failed\n");
 		return -1;
 	}
 
@@ -1142,12 +1117,12 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port)
 	 * (can't set it up in mos7840_startup as the  *
 	 * structures were not set up at that time.)   */
 
-	dbg("port number is %d", port->number);
-	dbg("serial number is %d", port->serial->minor);
-	dbg("Bulkin endpoint is %d", port->bulk_in_endpointAddress);
-	dbg("BulkOut endpoint is %d", port->bulk_out_endpointAddress);
-	dbg("Interrupt endpoint is %d", port->interrupt_in_endpointAddress);
-	dbg("port's number in the device is %d", mos7840_port->port_num);
+	dev_dbg(&port->dev, "port number is %d\n", port->number);
+	dev_dbg(&port->dev, "serial number is %d\n", port->serial->minor);
+	dev_dbg(&port->dev, "Bulkin endpoint is %d\n", port->bulk_in_endpointAddress);
+	dev_dbg(&port->dev, "BulkOut endpoint is %d\n", port->bulk_out_endpointAddress);
+	dev_dbg(&port->dev, "Interrupt endpoint is %d\n", port->interrupt_in_endpointAddress);
+	dev_dbg(&port->dev, "port's number in the device is %d\n", mos7840_port->port_num);
 	mos7840_port->read_urb = port->read_urb;
 
 	/* set up our bulk in urb */
@@ -1171,8 +1146,7 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port)
 			mos7840_bulk_in_callback, mos7840_port);
 	}
 
-	dbg("mos7840_open: bulkin endpoint is %d",
-	    port->bulk_in_endpointAddress);
+	dev_dbg(&port->dev, "%s: bulkin endpoint is %d\n", __func__, port->bulk_in_endpointAddress);
 	mos7840_port->read_urb_busy = true;
 	response = usb_submit_urb(mos7840_port->read_urb, GFP_KERNEL);
 	if (response) {
@@ -1197,9 +1171,6 @@ static int mos7840_open(struct tty_struct *tty, struct usb_serial_port *port)
 	mos7840_port->icount.tx = 0;
 	mos7840_port->icount.rx = 0;
 
-	dbg("usb_serial serial:%p       mos7840_port:%p\n      usb_serial_port port:%p",
-				serial, mos7840_port, port);
-
 	return 0;
 }
 
@@ -1221,10 +1192,8 @@ static int mos7840_chars_in_buffer(struct tty_struct *tty)
 	unsigned long flags;
 	struct moschip_port *mos7840_port;
 
-	if (mos7840_port_paranoia_check(port, __func__)) {
-		dbg("%s", "Invalid port");
+	if (mos7840_port_paranoia_check(port, __func__))
 		return 0;
-	}
 
 	mos7840_port = mos7840_get_port_private(port);
 	if (mos7840_port == NULL)
@@ -1238,7 +1207,7 @@ static int mos7840_chars_in_buffer(struct tty_struct *tty)
 		}
 	}
 	spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);
-	dbg("%s - returns %d", __func__, chars);
+	dev_dbg(&port->dev, "%s - returns %d\n", __func__, chars);
 	return chars;
 
 }
@@ -1256,16 +1225,12 @@ static void mos7840_close(struct usb_serial_port *port)
 	int j;
 	__u16 Data;
 
-	if (mos7840_port_paranoia_check(port, __func__)) {
-		dbg("%s", "Port Paranoia failed");
+	if (mos7840_port_paranoia_check(port, __func__))
 		return;
-	}
 
 	serial = mos7840_get_usb_serial(port, __func__);
-	if (!serial) {
-		dbg("%s", "Serial Paranoia failed");
+	if (!serial)
 		return;
-	}
 
 	mos7840_port = mos7840_get_port_private(port);
 	port0 = mos7840_get_port_private(serial->port[0]);
@@ -1291,27 +1256,26 @@ static void mos7840_close(struct usb_serial_port *port)
 	 * and interrupt read if they exists                  */
 	if (serial->dev) {
 		if (mos7840_port->write_urb) {
-			dbg("%s", "Shutdown bulk write");
+			dev_dbg(&port->dev, "%s", "Shutdown bulk write\n");
 			usb_kill_urb(mos7840_port->write_urb);
 		}
 		if (mos7840_port->read_urb) {
-			dbg("%s", "Shutdown bulk read");
+			dev_dbg(&port->dev, "%s", "Shutdown bulk read\n");
 			usb_kill_urb(mos7840_port->read_urb);
 			mos7840_port->read_urb_busy = false;
 		}
 		if ((&mos7840_port->control_urb)) {
-			dbg("%s", "Shutdown control read");
+			dev_dbg(&port->dev, "%s", "Shutdown control read\n");
 			/*/      usb_kill_urb (mos7840_port->control_urb); */
 		}
 	}
 /*      if(mos7840_port->ctrl_buf != NULL) */
 /*              kfree(mos7840_port->ctrl_buf); */
 	port0->open_ports--;
-	dbg("mos7840_num_open_ports in close%d:in port%d",
-	    port0->open_ports, port->number);
+	dev_dbg(&port->dev, "%s in close%d:in port%d\n", __func__, port0->open_ports, port->number);
 	if (port0->open_ports == 0) {
 		if (serial->port[0]->interrupt_in_urb) {
-			dbg("%s", "Shutdown interrupt_in_urb");
+			dev_dbg(&port->dev, "Shutdown interrupt_in_urb\n");
 			usb_kill_urb(serial->port[0]->interrupt_in_urb);
 		}
 	}
@@ -1363,7 +1327,7 @@ static void mos7840_block_until_chase_response(struct tty_struct *tty,
 		/* No activity.. count down section */
 		wait--;
 		if (wait == 0) {
-			dbg("%s - TIMEOUT", __func__);
+			dev_dbg(&mos7840_port->port->dev, "%s - TIMEOUT\n", __func__);
 			return;
 		} else {
 			/* Reset timeout value back to seconds */
@@ -1384,16 +1348,12 @@ static void mos7840_break(struct tty_struct *tty, int break_state)
 	struct usb_serial *serial;
 	struct moschip_port *mos7840_port;
 
-	if (mos7840_port_paranoia_check(port, __func__)) {
-		dbg("%s", "Port Paranoia failed");
+	if (mos7840_port_paranoia_check(port, __func__))
 		return;
-	}
 
 	serial = mos7840_get_usb_serial(port, __func__);
-	if (!serial) {
-		dbg("%s", "Serial Paranoia failed");
+	if (!serial)
 		return;
-	}
 
 	mos7840_port = mos7840_get_port_private(port);
 
@@ -1411,8 +1371,7 @@ static void mos7840_break(struct tty_struct *tty, int break_state)
 
 	/* FIXME: no locking on shadowLCR anywhere in driver */
 	mos7840_port->shadowLCR = data;
-	dbg("mcs7840_break mos7840_port->shadowLCR is %x",
-	    mos7840_port->shadowLCR);
+	dev_dbg(&port->dev, "%s mos7840_port->shadowLCR is %x\n", __func__, mos7840_port->shadowLCR);
 	mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER,
 			     mos7840_port->shadowLCR);
 }
@@ -1433,17 +1392,12 @@ static int mos7840_write_room(struct tty_struct *tty)
 	unsigned long flags;
 	struct moschip_port *mos7840_port;
 
-	if (mos7840_port_paranoia_check(port, __func__)) {
-		dbg("%s", "Invalid port");
-		dbg("%s", " mos7840_write_room:leaving ...........");
+	if (mos7840_port_paranoia_check(port, __func__))
 		return -1;
-	}
 
 	mos7840_port = mos7840_get_port_private(port);
-	if (mos7840_port == NULL) {
-		dbg("%s", "mos7840_break:leaving ...........");
+	if (mos7840_port == NULL)
 		return -1;
-	}
 
 	spin_lock_irqsave(&mos7840_port->pool_lock, flags);
 	for (i = 0; i < NUM_URBS; ++i) {
@@ -1453,7 +1407,7 @@ static int mos7840_write_room(struct tty_struct *tty)
 	spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);
 
 	room = (room == 0) ? 0 : room - URB_TRANSFER_BUFFER_SIZE + 1;
-	dbg("%s - returns %d", __func__, room);
+	dev_dbg(&mos7840_port->port->dev, "%s - returns %d\n", __func__, room);
 	return room;
 
 }
@@ -1486,9 +1440,8 @@ static int mos7840_write(struct tty_struct *tty, struct usb_serial_port *port,
 	Data = 0x00;
 	status = mos7840_get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);
 	mos7840_port->shadowLCR = Data;
-	dbg("mos7840_write: LINE_CONTROL_REGISTER is %x", Data);
-	dbg("mos7840_write: mos7840_port->shadowLCR is %x",
-	    mos7840_port->shadowLCR);
+	dev_dbg(&port->dev, "%s: LINE_CONTROL_REGISTER is %x\n", __func__, Data);
+	dev_dbg(&port->dev, "%s: mos7840_port->shadowLCR is %x\n", __func__, mos7840_port->shadowLCR);
 
 	/* Data = 0x03; */
 	/* status = mos7840_set_uart_reg(port,LINE_CONTROL_REGISTER,Data); */
@@ -1501,34 +1454,27 @@ static int mos7840_write(struct tty_struct *tty, struct usb_serial_port *port,
 	/* status = mos7840_set_uart_reg(port,DIVISOR_LATCH_LSB,Data); */
 	Data = 0x00;
 	status = mos7840_get_uart_reg(port, DIVISOR_LATCH_LSB, &Data);
-	dbg("mos7840_write:DLL value is %x", Data);
+	dev_dbg(&port->dev, "%s: DLL value is %x\n", __func__, Data);
 
 	Data = 0x0;
 	status = mos7840_get_uart_reg(port, DIVISOR_LATCH_MSB, &Data);
-	dbg("mos7840_write:DLM value is %x", Data);
+	dev_dbg(&port->dev, "%s: DLM value is %x\n", __func__, Data);
 
 	Data = Data & ~SERIAL_LCR_DLAB;
-	dbg("mos7840_write: mos7840_port->shadowLCR is %x",
-	    mos7840_port->shadowLCR);
+	dev_dbg(&port->dev, "%s: mos7840_port->shadowLCR is %x\n", __func__, mos7840_port->shadowLCR);
 	status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
 #endif
 
-	if (mos7840_port_paranoia_check(port, __func__)) {
-		dbg("%s", "Port Paranoia failed");
+	if (mos7840_port_paranoia_check(port, __func__))
 		return -1;
-	}
 
 	serial = port->serial;
-	if (mos7840_serial_paranoia_check(serial, __func__)) {
-		dbg("%s", "Serial Paranoia failed");
+	if (mos7840_serial_paranoia_check(serial, __func__))
 		return -1;
-	}
 
 	mos7840_port = mos7840_get_port_private(port);
-	if (mos7840_port == NULL) {
-		dbg("%s", "mos7840_port is NULL");
+	if (mos7840_port == NULL)
 		return -1;
-	}
 
 	/* try to find a free urb in the list */
 	urb = NULL;
@@ -1538,14 +1484,14 @@ static int mos7840_write(struct tty_struct *tty, struct usb_serial_port *port,
 		if (!mos7840_port->busy[i]) {
 			mos7840_port->busy[i] = 1;
 			urb = mos7840_port->write_urb_pool[i];
-			dbg("URB:%d", i);
+			dev_dbg(&port->dev, "URB:%d\n", i);
 			break;
 		}
 	}
 	spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);
 
 	if (urb == NULL) {
-		dbg("%s - no more free urbs", __func__);
+		dev_dbg(&port->dev, "%s - no more free urbs\n", __func__);
 		goto exit;
 	}
 
@@ -1585,7 +1531,7 @@ static int mos7840_write(struct tty_struct *tty, struct usb_serial_port *port,
 	}
 
 	data1 = urb->transfer_buffer;
-	dbg("bulkout endpoint is %d", port->bulk_out_endpointAddress);
+	dev_dbg(&port->dev, "bulkout endpoint is %d\n", port->bulk_out_endpointAddress);
 
 	/* Turn on LED */
 	if (mos7840_port->has_led && !mos7840_port->led_flag) {
@@ -1608,7 +1554,7 @@ static int mos7840_write(struct tty_struct *tty, struct usb_serial_port *port,
 	bytes_sent = transfer_size;
 	mos7840_port->icount.tx += transfer_size;
 	smp_wmb();
-	dbg("mos7840_port->icount.tx is %d:", mos7840_port->icount.tx);
+	dev_dbg(&port->dev, "mos7840_port->icount.tx is %d:\n", mos7840_port->icount.tx);
 exit:
 	return bytes_sent;
 
@@ -1626,12 +1572,8 @@ static void mos7840_throttle(struct tty_struct *tty)
 	struct moschip_port *mos7840_port;
 	int status;
 
-	if (mos7840_port_paranoia_check(port, __func__)) {
-		dbg("%s", "Invalid port");
+	if (mos7840_port_paranoia_check(port, __func__))
 		return;
-	}
-
-	dbg("- port %d", port->number);
 
 	mos7840_port = mos7840_get_port_private(port);
 
@@ -1639,7 +1581,7 @@ static void mos7840_throttle(struct tty_struct *tty)
 		return;
 
 	if (!mos7840_port->open) {
-		dbg("%s", "port not opened");
+		dev_dbg(&port->dev, "%s", "port not opened\n");
 		return;
 	}
 
@@ -1672,16 +1614,14 @@ static void mos7840_unthrottle(struct tty_struct *tty)
 	int status;
 	struct moschip_port *mos7840_port = mos7840_get_port_private(port);
 
-	if (mos7840_port_paranoia_check(port, __func__)) {
-		dbg("%s", "Invalid port");
+	if (mos7840_port_paranoia_check(port, __func__))
 		return;
-	}
 
 	if (mos7840_port == NULL)
 		return;
 
 	if (!mos7840_port->open) {
-		dbg("%s - port not opened", __func__);
+		dev_dbg(&port->dev, "%s - port not opened\n", __func__);
 		return;
 	}
 
@@ -1726,7 +1666,7 @@ static int mos7840_tiocmget(struct tty_struct *tty)
 	    | ((msr & MOS7840_MSR_RI) ? TIOCM_RI : 0)
 	    | ((msr & MOS7840_MSR_DSR) ? TIOCM_DSR : 0);
 
-	dbg("%s - 0x%04X", __func__, result);
+	dev_dbg(&port->dev, "%s - 0x%04X\n", __func__, result);
 
 	return result;
 }
@@ -1764,7 +1704,7 @@ static int mos7840_tiocmset(struct tty_struct *tty,
 
 	status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER, mcr);
 	if (status < 0) {
-		dbg("setting MODEM_CONTROL_REGISTER Failed");
+		dev_dbg(&port->dev, "setting MODEM_CONTROL_REGISTER Failed\n");
 		return status;
 	}
 
@@ -1776,10 +1716,11 @@ static int mos7840_tiocmset(struct tty_struct *tty,
  *	this function calculates the proper baud rate divisor for the specified
  *	baud rate.
  *****************************************************************************/
-static int mos7840_calc_baud_rate_divisor(int baudRate, int *divisor,
+static int mos7840_calc_baud_rate_divisor(struct usb_serial_port *port,
+					  int baudRate, int *divisor,
 					  __u16 *clk_sel_val)
 {
-	dbg("%s - %d", __func__, baudRate);
+	dev_dbg(&port->dev, "%s - %d\n", __func__, baudRate);
 
 	if (baudRate <= 115200) {
 		*divisor = 115200 / baudRate;
@@ -1832,11 +1773,11 @@ static int mos7840_calc_baud_rate_divisor(int baudRate, int *divisor,
 			custom++;
 		*divisor = custom;
 
-		dbg(" Baud %d = %d", baudrate, custom);
+		dev_dbg(&port->dev, " Baud %d = %d\n", baudrate, custom);
 		return 0;
 	}
 
-	dbg("%s", " Baud calculation Failed...");
+	dev_dbg(&port->dev, "%s", " Baud calculation Failed...\n");
 	return -1;
 #endif
 }
@@ -1860,21 +1801,17 @@ static int mos7840_send_cmd_write_baud_rate(struct moschip_port *mos7840_port,
 	if (mos7840_port == NULL)
 		return -1;
 
-	port = (struct usb_serial_port *)mos7840_port->port;
-	if (mos7840_port_paranoia_check(port, __func__)) {
-		dbg("%s", "Invalid port");
+	port = mos7840_port->port;
+	if (mos7840_port_paranoia_check(port, __func__))
 		return -1;
-	}
 
-	if (mos7840_serial_paranoia_check(port->serial, __func__)) {
-		dbg("%s", "Invalid Serial");
+	if (mos7840_serial_paranoia_check(port->serial, __func__))
 		return -1;
-	}
 
 	number = mos7840_port->port->number - mos7840_port->port->serial->minor;
 
-	dbg("%s - port = %d, baud = %d", __func__,
-	    mos7840_port->port->number, baudRate);
+	dev_dbg(&port->dev, "%s - port = %d, baud = %d\n", __func__,
+		mos7840_port->port->number, baudRate);
 	/* reset clk_uart_sel in spregOffset */
 	if (baudRate > 115200) {
 #ifdef HW_flow_control
@@ -1885,7 +1822,7 @@ static int mos7840_send_cmd_write_baud_rate(struct moschip_port *mos7840_port,
 		status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
 									Data);
 		if (status < 0) {
-			dbg("Writing spreg failed in set_serial_baud");
+			dev_dbg(&port->dev, "Writing spreg failed in set_serial_baud\n");
 			return -1;
 		}
 #endif
@@ -1898,7 +1835,7 @@ static int mos7840_send_cmd_write_baud_rate(struct moschip_port *mos7840_port,
 		status = mos7840_set_uart_reg(port, MODEM_CONTROL_REGISTER,
 									Data);
 		if (status < 0) {
-			dbg("Writing spreg failed in set_serial_baud");
+			dev_dbg(&port->dev, "Writing spreg failed in set_serial_baud\n");
 			return -1;
 		}
 #endif
@@ -1908,19 +1845,19 @@ static int mos7840_send_cmd_write_baud_rate(struct moschip_port *mos7840_port,
 	if (1) {		/* baudRate <= 115200) */
 		clk_sel_val = 0x0;
 		Data = 0x0;
-		status = mos7840_calc_baud_rate_divisor(baudRate, &divisor,
+		status = mos7840_calc_baud_rate_divisor(port, baudRate, &divisor,
 						   &clk_sel_val);
 		status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset,
 								 &Data);
 		if (status < 0) {
-			dbg("reading spreg failed in set_serial_baud");
+			dev_dbg(&port->dev, "reading spreg failed in set_serial_baud\n");
 			return -1;
 		}
 		Data = (Data & 0x8f) | clk_sel_val;
 		status = mos7840_set_reg_sync(port, mos7840_port->SpRegOffset,
 								Data);
 		if (status < 0) {
-			dbg("Writing spreg failed in set_serial_baud");
+			dev_dbg(&port->dev, "Writing spreg failed in set_serial_baud\n");
 			return -1;
 		}
 		/* Calculate the Divisor */
@@ -1936,11 +1873,11 @@ static int mos7840_send_cmd_write_baud_rate(struct moschip_port *mos7840_port,
 
 		/* Write the divisor */
 		Data = (unsigned char)(divisor & 0xff);
-		dbg("set_serial_baud Value to write DLL is %x", Data);
+		dev_dbg(&port->dev, "set_serial_baud Value to write DLL is %x\n", Data);
 		mos7840_set_uart_reg(port, DIVISOR_LATCH_LSB, Data);
 
 		Data = (unsigned char)((divisor & 0xff00) >> 8);
-		dbg("set_serial_baud Value to write DLM is %x", Data);
+		dev_dbg(&port->dev, "set_serial_baud Value to write DLM is %x\n", Data);
 		mos7840_set_uart_reg(port, DIVISOR_LATCH_MSB, Data);
 
 		/* Disable access to divisor latch */
@@ -1975,24 +1912,18 @@ static void mos7840_change_port_settings(struct tty_struct *tty,
 	if (mos7840_port == NULL)
 		return;
 
-	port = (struct usb_serial_port *)mos7840_port->port;
+	port = mos7840_port->port;
 
-	if (mos7840_port_paranoia_check(port, __func__)) {
-		dbg("%s", "Invalid port");
+	if (mos7840_port_paranoia_check(port, __func__))
 		return;
-	}
 
-	if (mos7840_serial_paranoia_check(port->serial, __func__)) {
-		dbg("%s", "Invalid Serial");
+	if (mos7840_serial_paranoia_check(port->serial, __func__))
 		return;
-	}
 
 	serial = port->serial;
 
-	dbg("%s - port %d", __func__, mos7840_port->port->number);
-
 	if (!mos7840_port->open) {
-		dbg("%s - port not opened", __func__);
+		dev_dbg(&port->dev, "%s - port not opened\n", __func__);
 		return;
 	}
 
@@ -2027,14 +1958,14 @@ static void mos7840_change_port_settings(struct tty_struct *tty,
 	if (cflag & PARENB) {
 		if (cflag & PARODD) {
 			lParity = LCR_PAR_ODD;
-			dbg("%s - parity = odd", __func__);
+			dev_dbg(&port->dev, "%s - parity = odd\n", __func__);
 		} else {
 			lParity = LCR_PAR_EVEN;
-			dbg("%s - parity = even", __func__);
+			dev_dbg(&port->dev, "%s - parity = even\n", __func__);
 		}
 
 	} else {
-		dbg("%s - parity = none", __func__);
+		dev_dbg(&port->dev, "%s - parity = none\n", __func__);
 	}
 
 	if (cflag & CMSPAR)
@@ -2043,10 +1974,10 @@ static void mos7840_change_port_settings(struct tty_struct *tty,
 	/* Change the Stop bit */
 	if (cflag & CSTOPB) {
 		lStop = LCR_STOP_2;
-		dbg("%s - stop bits = 2", __func__);
+		dev_dbg(&port->dev, "%s - stop bits = 2\n", __func__);
 	} else {
 		lStop = LCR_STOP_1;
-		dbg("%s - stop bits = 1", __func__);
+		dev_dbg(&port->dev, "%s - stop bits = 1\n", __func__);
 	}
 
 	/* Update the LCR with the correct value */
@@ -2054,8 +1985,8 @@ static void mos7840_change_port_settings(struct tty_struct *tty,
 	    ~(LCR_BITS_MASK | LCR_STOP_MASK | LCR_PAR_MASK);
 	mos7840_port->shadowLCR |= (lData | lParity | lStop);
 
-	dbg("mos7840_change_port_settings mos7840_port->shadowLCR is %x",
-	    mos7840_port->shadowLCR);
+	dev_dbg(&port->dev, "%s - mos7840_port->shadowLCR is %x\n", __func__,
+		mos7840_port->shadowLCR);
 	/* Disable Interrupts */
 	Data = 0x00;
 	mos7840_set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
@@ -2096,11 +2027,11 @@ static void mos7840_change_port_settings(struct tty_struct *tty,
 
 	if (!baud) {
 		/* pick a default, any default... */
-		dbg("%s", "Picked default baud...");
+		dev_dbg(&port->dev, "%s", "Picked default baud...\n");
 		baud = 9600;
 	}
 
-	dbg("%s - baud rate = %d", __func__, baud);
+	dev_dbg(&port->dev, "%s - baud rate = %d\n", __func__, baud);
 	status = mos7840_send_cmd_write_baud_rate(mos7840_port, baud);
 
 	/* Enable Interrupts */
@@ -2111,15 +2042,15 @@ static void mos7840_change_port_settings(struct tty_struct *tty,
 		mos7840_port->read_urb_busy = true;
 		status = usb_submit_urb(mos7840_port->read_urb, GFP_ATOMIC);
 		if (status) {
-			dbg("usb_submit_urb(read bulk) failed, status = %d",
+			dev_dbg(&port->dev, "usb_submit_urb(read bulk) failed, status = %d\n",
 			    status);
 			mos7840_port->read_urb_busy = false;
 		}
 	}
 	wake_up(&mos7840_port->delta_msr_wait);
 	mos7840_port->delta_msr_cond = 1;
-	dbg("mos7840_change_port_settings mos7840_port->shadowLCR is End %x",
-	    mos7840_port->shadowLCR);
+	dev_dbg(&port->dev, "%s - mos7840_port->shadowLCR is End %x\n", __func__,
+		mos7840_port->shadowLCR);
 }
 
 /*****************************************************************************
@@ -2137,17 +2068,13 @@ static void mos7840_set_termios(struct tty_struct *tty,
 	struct usb_serial *serial;
 	struct moschip_port *mos7840_port;
 
-	if (mos7840_port_paranoia_check(port, __func__)) {
-		dbg("%s", "Invalid port");
+	if (mos7840_port_paranoia_check(port, __func__))
 		return;
-	}
 
 	serial = port->serial;
 
-	if (mos7840_serial_paranoia_check(serial, __func__)) {
-		dbg("%s", "Invalid Serial");
+	if (mos7840_serial_paranoia_check(serial, __func__))
 		return;
-	}
 
 	mos7840_port = mos7840_get_port_private(port);
 
@@ -2155,26 +2082,26 @@ static void mos7840_set_termios(struct tty_struct *tty,
 		return;
 
 	if (!mos7840_port->open) {
-		dbg("%s - port not opened", __func__);
+		dev_dbg(&port->dev, "%s - port not opened\n", __func__);
 		return;
 	}
 
-	dbg("%s", "setting termios - ");
+	dev_dbg(&port->dev, "%s", "setting termios - \n");
 
 	cflag = tty->termios->c_cflag;
 
-	dbg("%s - clfag %08x iflag %08x", __func__,
-	    tty->termios->c_cflag, RELEVANT_IFLAG(tty->termios->c_iflag));
-	dbg("%s - old clfag %08x old iflag %08x", __func__,
-	    old_termios->c_cflag, RELEVANT_IFLAG(old_termios->c_iflag));
-	dbg("%s - port %d", __func__, port->number);
+	dev_dbg(&port->dev, "%s - clfag %08x iflag %08x\n", __func__,
+		tty->termios->c_cflag, RELEVANT_IFLAG(tty->termios->c_iflag));
+	dev_dbg(&port->dev, "%s - old clfag %08x old iflag %08x\n", __func__,
+		old_termios->c_cflag, RELEVANT_IFLAG(old_termios->c_iflag));
+	dev_dbg(&port->dev, "%s - port %d\n", __func__, port->number);
 
 	/* change the port settings to the new ones specified */
 
 	mos7840_change_port_settings(tty, mos7840_port, old_termios);
 
 	if (!mos7840_port->read_urb) {
-		dbg("%s", "URB KILLED !!!!!");
+		dev_dbg(&port->dev, "%s", "URB KILLED !!!!!\n");
 		return;
 	}
 
@@ -2182,7 +2109,7 @@ static void mos7840_set_termios(struct tty_struct *tty,
 		mos7840_port->read_urb_busy = true;
 		status = usb_submit_urb(mos7840_port->read_urb, GFP_ATOMIC);
 		if (status) {
-			dbg("usb_submit_urb(read bulk) failed, status = %d",
+			dev_dbg(&port->dev, "usb_submit_urb(read bulk) failed, status = %d\n",
 			    status);
 			mos7840_port->read_urb_busy = false;
 		}
@@ -2207,10 +2134,8 @@ static int mos7840_get_lsr_info(struct tty_struct *tty,
 	unsigned int result = 0;
 
 	count = mos7840_chars_in_buffer(tty);
-	if (count == 0) {
-		dbg("%s -- Empty", __func__);
+	if (count == 0)
 		result = TIOCSER_TEMT;
-	}
 
 	if (copy_to_user(value, &result, sizeof(int)))
 		return -EFAULT;
@@ -2273,8 +2198,8 @@ static int mos7840_get_icount(struct tty_struct *tty,
 	icount->brk = cnow.brk;
 	icount->buf_overrun = cnow.buf_overrun;
 
-	dbg("%s (%d) TIOCGICOUNT RX=%d, TX=%d", __func__,
-		port->number, icount->rx, icount->tx);
+	dev_dbg(&port->dev, "%s TIOCGICOUNT RX=%d, TX=%d\n", __func__,
+		icount->rx, icount->tx);
 	return 0;
 }
 
@@ -2293,35 +2218,33 @@ static int mos7840_ioctl(struct tty_struct *tty,
 	struct async_icount cnow;
 	struct async_icount cprev;
 
-	if (mos7840_port_paranoia_check(port, __func__)) {
-		dbg("%s", "Invalid port");
+	if (mos7840_port_paranoia_check(port, __func__))
 		return -1;
-	}
 
 	mos7840_port = mos7840_get_port_private(port);
 
 	if (mos7840_port == NULL)
 		return -1;
 
-	dbg("%s - port %d, cmd = 0x%x", __func__, port->number, cmd);
+	dev_dbg(&port->dev, "%s - cmd = 0x%x\n", __func__, cmd);
 
 	switch (cmd) {
 		/* return number of bytes available */
 
 	case TIOCSERGETLSR:
-		dbg("%s (%d) TIOCSERGETLSR", __func__, port->number);
+		dev_dbg(&port->dev, "%s TIOCSERGETLSR\n", __func__);
 		return mos7840_get_lsr_info(tty, argp);
 
 	case TIOCGSERIAL:
-		dbg("%s (%d) TIOCGSERIAL", __func__, port->number);
+		dev_dbg(&port->dev, "%s TIOCGSERIAL\n", __func__);
 		return mos7840_get_serial_info(mos7840_port, argp);
 
 	case TIOCSSERIAL:
-		dbg("%s (%d) TIOCSSERIAL", __func__, port->number);
+		dev_dbg(&port->dev, "%s TIOCSSERIAL\n", __func__);
 		break;
 
 	case TIOCMIWAIT:
-		dbg("%s (%d) TIOCMIWAIT", __func__, port->number);
+		dev_dbg(&port->dev, "%s  TIOCMIWAIT\n", __func__);
 		cprev = mos7840_port->icount;
 		while (1) {
 			/* interruptible_sleep_on(&mos7840_port->delta_msr_wait); */
@@ -2437,11 +2360,6 @@ static int mos7840_startup(struct usb_serial *serial)
 	int i, status;
 	__u16 Data;
 
-	if (!serial) {
-		dbg("%s", "Invalid Handler");
-		return -1;
-	}
-
 	dev = serial->dev;
 
 	/* we set up the pointers to the endpoints in the mos7840_open *
@@ -2449,7 +2367,7 @@ static int mos7840_startup(struct usb_serial *serial)
 
 	/* set up port private structures */
 	for (i = 0; i < serial->num_ports; ++i) {
-		dbg ("mos7840_startup: configuring port %d............", i);
+		dev_dbg(&dev->dev, "mos7840_startup: configuring port %d............\n", i);
 		mos7840_port = kzalloc(sizeof(struct moschip_port), GFP_KERNEL);
 		if (mos7840_port == NULL) {
 			dev_err(&dev->dev, "%s - Out of memory\n", __func__);
@@ -2470,10 +2388,10 @@ static int mos7840_startup(struct usb_serial *serial)
 		 * usb-serial.c:get_free_serial() and cannot therefore be used
 		 * to index device instances */
 		mos7840_port->port_num = i + 1;
-		dbg ("serial->port[i]->number = %d", serial->port[i]->number);
-		dbg ("serial->port[i]->serial->minor = %d", serial->port[i]->serial->minor);
-		dbg ("mos7840_port->port_num = %d", mos7840_port->port_num);
-		dbg ("serial->minor = %d", serial->minor);
+		dev_dbg(&dev->dev, "serial->port[i]->number = %d\n", serial->port[i]->number);
+		dev_dbg(&dev->dev, "serial->port[i]->serial->minor = %d\n", serial->port[i]->serial->minor);
+		dev_dbg(&dev->dev, "mos7840_port->port_num = %d\n", mos7840_port->port_num);
+		dev_dbg(&dev->dev, "serial->minor = %d\n", serial->minor);
 
 		if (mos7840_port->port_num == 1) {
 			mos7840_port->SpRegOffset = 0x0;
@@ -2500,18 +2418,17 @@ static int mos7840_startup(struct usb_serial *serial)
 			mos7840_port->ControlRegOffset = 0xd;
 			mos7840_port->DcrRegOffset = 0x1c;
 		}
-		mos7840_dump_serial_port(mos7840_port);
+		mos7840_dump_serial_port(serial->port[i], mos7840_port);
 		mos7840_set_port_private(serial->port[i], mos7840_port);
 
 		/* enable rx_disable bit in control register */
 		status = mos7840_get_reg_sync(serial->port[i],
 				 mos7840_port->ControlRegOffset, &Data);
 		if (status < 0) {
-			dbg("Reading ControlReg failed status-0x%x", status);
+			dev_dbg(&dev->dev, "Reading ControlReg failed status-0x%x\n", status);
 			break;
 		} else
-			dbg("ControlReg Reading success val is %x, status%d",
-			    Data, status);
+			dev_dbg(&dev->dev, "ControlReg Reading success val is %x, status%d\n", Data, status);
 		Data |= 0x08;	/* setting driver done bit */
 		Data |= 0x04;	/* sp1_bit to have cts change reflect in
 				   modem status reg */
@@ -2520,11 +2437,10 @@ static int mos7840_startup(struct usb_serial *serial)
 		status = mos7840_set_reg_sync(serial->port[i],
 					 mos7840_port->ControlRegOffset, Data);
 		if (status < 0) {
-			dbg("Writing ControlReg failed(rx_disable) status-0x%x", status);
+			dev_dbg(&dev->dev, "Writing ControlReg failed(rx_disable) status-0x%x\n", status);
 			break;
 		} else
-			dbg("ControlReg Writing success(rx_disable) status%d",
-			    status);
+			dev_dbg(&dev->dev, "ControlReg Writing success(rx_disable) status%d\n", status);
 
 		/* Write default values in DCR (i.e 0x01 in DCR0, 0x05 in DCR2
 		   and 0x24 in DCR3 */
@@ -2532,61 +2448,57 @@ static int mos7840_startup(struct usb_serial *serial)
 		status = mos7840_set_reg_sync(serial->port[i],
 			 (__u16) (mos7840_port->DcrRegOffset + 0), Data);
 		if (status < 0) {
-			dbg("Writing DCR0 failed status-0x%x", status);
+			dev_dbg(&dev->dev, "Writing DCR0 failed status-0x%x\n", status);
 			break;
 		} else
-			dbg("DCR0 Writing success status%d", status);
+			dev_dbg(&dev->dev, "DCR0 Writing success status%d\n", status);
 
 		Data = 0x05;
 		status = mos7840_set_reg_sync(serial->port[i],
 			 (__u16) (mos7840_port->DcrRegOffset + 1), Data);
 		if (status < 0) {
-			dbg("Writing DCR1 failed status-0x%x", status);
+			dev_dbg(&dev->dev, "Writing DCR1 failed status-0x%x\n", status);
 			break;
 		} else
-			dbg("DCR1 Writing success status%d", status);
+			dev_dbg(&dev->dev, "DCR1 Writing success status%d\n", status);
 
 		Data = 0x24;
 		status = mos7840_set_reg_sync(serial->port[i],
 			 (__u16) (mos7840_port->DcrRegOffset + 2), Data);
 		if (status < 0) {
-			dbg("Writing DCR2 failed status-0x%x", status);
+			dev_dbg(&dev->dev, "Writing DCR2 failed status-0x%x\n", status);
 			break;
 		} else
-			dbg("DCR2 Writing success status%d", status);
+			dev_dbg(&dev->dev, "DCR2 Writing success status%d\n", status);
 
 		/* write values in clkstart0x0 and clkmulti 0x20 */
 		Data = 0x0;
 		status = mos7840_set_reg_sync(serial->port[i],
 					 CLK_START_VALUE_REGISTER, Data);
 		if (status < 0) {
-			dbg("Writing CLK_START_VALUE_REGISTER failed status-0x%x", status);
+			dev_dbg(&dev->dev, "Writing CLK_START_VALUE_REGISTER failed status-0x%x\n", status);
 			break;
 		} else
-			dbg("CLK_START_VALUE_REGISTER Writing success status%d", status);
+			dev_dbg(&dev->dev, "CLK_START_VALUE_REGISTER Writing success status%d\n", status);
 
 		Data = 0x20;
 		status = mos7840_set_reg_sync(serial->port[i],
 					CLK_MULTI_REGISTER, Data);
 		if (status < 0) {
-			dbg("Writing CLK_MULTI_REGISTER failed status-0x%x",
-			    status);
+			dev_dbg(&dev->dev, "Writing CLK_MULTI_REGISTER failed status-0x%x\n", status);
 			goto error;
 		} else
-			dbg("CLK_MULTI_REGISTER Writing success status%d",
-			    status);
+			dev_dbg(&dev->dev, "CLK_MULTI_REGISTER Writing success status%d\n", status);
 
 		/* write value 0x0 to scratchpad register */
 		Data = 0x00;
 		status = mos7840_set_uart_reg(serial->port[i],
 						SCRATCH_PAD_REGISTER, Data);
 		if (status < 0) {
-			dbg("Writing SCRATCH_PAD_REGISTER failed status-0x%x",
-			    status);
+			dev_dbg(&dev->dev, "Writing SCRATCH_PAD_REGISTER failed status-0x%x\n", status);
 			break;
 		} else
-			dbg("SCRATCH_PAD_REGISTER Writing success status%d",
-			    status);
+			dev_dbg(&dev->dev, "SCRATCH_PAD_REGISTER Writing success status%d\n", status);
 
 		/* Zero Length flag register */
 		if ((mos7840_port->port_num != 1)
@@ -2596,31 +2508,25 @@ static int mos7840_startup(struct usb_serial *serial)
 			status = mos7840_set_reg_sync(serial->port[i],
 				      (__u16) (ZLP_REG1 +
 				      ((__u16)mos7840_port->port_num)), Data);
-			dbg("ZLIP offset %x",
-			    (__u16) (ZLP_REG1 +
-					((__u16) mos7840_port->port_num)));
+			dev_dbg(&dev->dev, "ZLIP offset %x\n",
+				(__u16)(ZLP_REG1 + ((__u16) mos7840_port->port_num)));
 			if (status < 0) {
-				dbg("Writing ZLP_REG%d failed status-0x%x",
-				    i + 2, status);
+				dev_dbg(&dev->dev, "Writing ZLP_REG%d failed status-0x%x\n", i + 2, status);
 				break;
 			} else
-				dbg("ZLP_REG%d Writing success status%d",
-				    i + 2, status);
+				dev_dbg(&dev->dev, "ZLP_REG%d Writing success status%d\n", i + 2, status);
 		} else {
 			Data = 0xff;
 			status = mos7840_set_reg_sync(serial->port[i],
 			      (__u16) (ZLP_REG1 +
 			      ((__u16)mos7840_port->port_num) - 0x1), Data);
-			dbg("ZLIP offset %x",
-			    (__u16) (ZLP_REG1 +
-				     ((__u16) mos7840_port->port_num) - 0x1));
+			dev_dbg(&dev->dev, "ZLIP offset %x\n",
+				(__u16)(ZLP_REG1 + ((__u16) mos7840_port->port_num) - 0x1));
 			if (status < 0) {
-				dbg("Writing ZLP_REG%d failed status-0x%x",
-				    i + 1, status);
+				dev_dbg(&dev->dev, "Writing ZLP_REG%d failed status-0x%x\n", i + 1, status);
 				break;
 			} else
-				dbg("ZLP_REG%d Writing success status%d",
-				    i + 1, status);
+				dev_dbg(&dev->dev, "ZLP_REG%d Writing success status%d\n", i + 1, status);
 
 		}
 		mos7840_port->control_urb = usb_alloc_urb(0, GFP_KERNEL);
@@ -2661,16 +2567,15 @@ static int mos7840_startup(struct usb_serial *serial)
 						MODEM_CONTROL_REGISTER, 0x0300);
 		}
 	}
-	dbg ("mos7840_startup: all ports configured...........");
 
 	/* Zero Length flag enable */
 	Data = 0x0f;
 	status = mos7840_set_reg_sync(serial->port[0], ZLP_REG5, Data);
 	if (status < 0) {
-		dbg("Writing ZLP_REG5 failed status-0x%x", status);
+		dev_dbg(&dev->dev, "Writing ZLP_REG5 failed status-0x%x\n", status);
 		goto error;
 	} else
-		dbg("ZLP_REG5 Writing success status%d", status);
+		dev_dbg(&dev->dev, "ZLP_REG5 Writing success status%d\n", status);
 
 	/* setting configuration feature to one */
 	usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
@@ -2700,11 +2605,6 @@ static void mos7840_disconnect(struct usb_serial *serial)
 	unsigned long flags;
 	struct moschip_port *mos7840_port;
 
-	if (!serial) {
-		dbg("%s", "Invalid Handler");
-		return;
-	}
-
 	/* check for the ports to be closed,close the ports and disconnect */
 
 	/* free private structure allocated for serial port  *
@@ -2712,7 +2612,6 @@ static void mos7840_disconnect(struct usb_serial *serial)
 
 	for (i = 0; i < serial->num_ports; ++i) {
 		mos7840_port = mos7840_get_port_private(serial->port[i]);
-		dbg ("mos7840_port %d = %p", i, mos7840_port);
 		if (mos7840_port) {
 			spin_lock_irqsave(&mos7840_port->pool_lock, flags);
 			mos7840_port->zombie = 1;
@@ -2732,11 +2631,6 @@ static void mos7840_release(struct usb_serial *serial)
 	int i;
 	struct moschip_port *mos7840_port;
 
-	if (!serial) {
-		dbg("%s", "Invalid Handler");
-		return;
-	}
-
 	/* check for the ports to be closed,close the ports and disconnect */
 
 	/* free private structure allocated for serial port  *
@@ -2744,7 +2638,6 @@ static void mos7840_release(struct usb_serial *serial)
 
 	for (i = 0; i < serial->num_ports; ++i) {
 		mos7840_port = mos7840_get_port_private(serial->port[i]);
-		dbg("mos7840_port %d = %p", i, mos7840_port);
 		if (mos7840_port) {
 			if (mos7840_port->has_led) {
 				/* Turn off LED */