Merge tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt

First batch of DT changes for 4.5:
- addition of nodes for sama5d2 & sama5d4
- some fixes for i2c hold time, compatible stings
- addition of a new patform by DENX: the MA5D4 SoM and EVK

* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
  ARM: at91/dt: sama5d2 Xplained: pmic needs a specific sda hold time
  ARM: at91/dt: sama5d4: update i2c compatible string
  ARM: at91/dt: sama5d4 master clock can run at 200MHz now
  ARM: at91/dt: sama5d2: add watchdog node
  ARM: at91/dt: sama5d4: Add support for DENX MA5D4 SoM and EVK
  ARM: at91/dt: sama5d4: Add pinmux for 8-bit MMC0 bus
  ARM: at91/dt: sama5d4: Fix mmc0 pinmux comments

Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/Makefile

@@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
 	sama5d34ek.dtb \
 	sama5d35ek.dtb \
 	sama5d36ek.dtb \
+	at91-sama5d4_ma5d4evk.dtb \
 	at91-sama5d4_xplained.dtb \
 	at91-sama5d4ek.dtb
 dtb-$(CONFIG_ARCH_ATLAS6) += \

arch/arm/boot/dts/at91-sama5d2_xplained.dts

@@ -129,6 +129,7 @@
 				dmas = <0>, <0>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_i2c0_default>;
+				i2c-sda-hold-time-ns = <350>;
 				status = "okay";
 
 				pmic: act8865@5b {
@@ -206,6 +207,10 @@
 				};
 			};
 
+			watchdog@f8048040 {
+				status = "okay";
+			};
+
 			uart3: serial@fc008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart3_default>;

arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi

@@ -0,0 +1,127 @@
+/*
+ * Copyright (C) 2015 Marek Vasut <marex@denx.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include "sama5d4.dtsi"
+
+/ {
+	model = "DENX MA5D4";
+	compatible = "denx,ma5d4", "atmel,sama5d4", "atmel,sama5";
+
+	memory {
+		reg = <0x20000000 0x10000000>;
+	};
+
+	clocks {
+		main_clock: main_clock {
+			compatible = "atmel,osc", "fixed-clock";
+			clock-frequency = <12000000>;
+		};
+
+		clk20m: clk20m {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <20000000>;
+			clock-output-names = "clk20m";
+		};
+	};
+
+	ahb {
+		apb {
+			mmc0: mmc@f8000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_dat4_7>;
+				vmmc-supply = <&vcc_mmc0_reg>;
+				vqmmc-supply = <&vcc_3v3_reg>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <8>;
+					broken-cd;
+				};
+			};
+
+			spi0: spi@f8010000 {
+				cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
+				status = "okay";
+
+				m25p80@0 {
+					compatible = "atmel,at25df321a";
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+				};
+			};
+
+			i2c0: i2c@f8014000 {
+				status = "okay";
+			};
+
+			spi1: spi@fc018000 {
+				cs-gpios = <&pioB 22 0>, <&pioB 23 0>, <0>, <0>;
+				status = "okay";
+
+				can0: can@0 {
+					compatible = "microchip,mcp2515";
+					reg = <0>;
+					clocks = <&clk20m>;
+					interrupt-parent = <&pioE>;
+					interrupts = <6 GPIO_ACTIVE_LOW>;
+					spi-max-frequency = <10000000>;
+				};
+
+				can1: can@1 {
+					compatible = "microchip,mcp2515";
+					reg = <1>;
+					clocks = <&clk20m>;
+					interrupt-parent = <&pioE>;
+					interrupts = <7 GPIO_ACTIVE_LOW>;
+					spi-max-frequency = <10000000>;
+				};
+			};
+
+			adc0: adc@fc034000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <
+					/* external trigger conflicts with USBA_VBUS */
+					&pinctrl_adc0_ad0
+					&pinctrl_adc0_ad1
+					&pinctrl_adc0_ad2
+					&pinctrl_adc0_ad3
+					&pinctrl_adc0_ad4
+					>;
+				atmel,adc-vref = <3300>;
+				status = "okay";
+			};
+
+			watchdog@fc068640 {
+				status = "okay";
+			};
+		};
+	};
+
+	vcc_3v3_reg: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC 3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vcc_mmc0_reg: fixedregulator@1 {
+		compatible = "regulator-fixed";
+		gpio = <&pioE 15 GPIO_ACTIVE_HIGH>;
+		regulator-name = "RST_n MCI0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3_reg>;
+		regulator-boot-on;
+	};
+};

arch/arm/boot/dts/at91-sama5d4_ma5d4evk.dts

@@ -0,0 +1,170 @@
+/*
+ * Copyright (C) 2015 Marek Vasut <marex@denx.de>
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+#include "at91-sama5d4_ma5d4.dtsi"
+
+/ {
+	model = "DENX MA5D4EVK";
+	compatible = "denx,ma5d4evk", "atmel,sama5d4", "atmel,sama5";
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+
+	ahb {
+		usb0: gadget@00400000 {
+			atmel,vbus-gpio = <&pioE 31 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+
+		usb1: ohci@00500000 {
+			num-ports = <3>;
+			atmel,vbus-gpio = <0
+					   &pioE 11 GPIO_ACTIVE_LOW
+					   &pioE 14 GPIO_ACTIVE_LOW
+					  >;
+			status = "okay";
+		};
+
+		usb2: ehci@00600000 {
+			status = "okay";
+		};
+
+		apb {
+			hlcdc: hlcdc@f0000000 {
+				status = "okay";
+
+				hlcdc-display-controller {
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_lcd_base &pinctrl_lcd_rgb888>;
+
+					port@0 {
+						hlcdc_panel_output: endpoint@0 {
+							reg = <0>;
+							remote-endpoint = <&panel_input>;
+						};
+					};
+				};
+
+			};
+
+			macb0: ethernet@f8020000 {
+				phy-mode = "rmii";
+				status = "okay";
+
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+			};
+
+			usart0: serial@f802c000 {
+				status = "okay";
+			};
+
+			usart1: serial@f8030000 {
+				status = "okay";
+			};
+
+			mmc1: mmc@fc000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+				vmmc-supply = <&vcc_mmc1_reg>;
+				vqmmc-supply = <&vcc_3v3_reg>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioE 5 0>;
+				};
+			};
+
+			adc0: adc@fc034000 {
+				atmel,adc-ts-wires = <4>;
+				atmel,adc-ts-pressure-threshold = <10000>;
+			};
+
+
+			pinctrl@fc06a000 {
+				board {
+					pinctrl_mmc1_cd: mmc1_cd {
+						atmel,pins = <AT91_PIOE 5 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+					};
+					pinctrl_usba_vbus: usba_vbus {
+						atmel,pins =
+							<AT91_PIOE 31 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+					};
+				};
+			};
+		};
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&hlcdc_pwm 0 50000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		status = "okay";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		status = "okay";
+
+		user1 {
+			label = "user1";
+			gpios = <&pioD 28 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		user2 {
+			label = "user2";
+			gpios = <&pioD 29 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		user3 {
+			label = "user3";
+			gpios = <&pioD 30 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	panel: panel {
+		/* Actually Ampire 800480R2 */
+		compatible = "foxlink,fl500wvr00-a0t", "simple-panel";
+		backlight = <&backlight>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		port@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			panel_input: endpoint@0 {
+				reg = <0>;
+				remote-endpoint = <&hlcdc_panel_output>;
+			};
+		};
+	};
+
+	vcc_mmc1_reg: fixedregulator@2 {
+		compatible = "regulator-fixed";
+		gpio = <&pioE 17 GPIO_ACTIVE_LOW>;
+		regulator-name = "VDD MCI1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3_reg>;
+	};
+};

arch/arm/boot/dts/sama5d2.dtsi

@@ -929,6 +929,13 @@
 				clocks = <&h32ck>;
 			};
 
+			watchdog@f8048040 {
+				compatible = "atmel,sama5d4-wdt";
+				reg = <0xf8048040 0x10>;
+				interrupts = <4 IRQ_TYPE_LEVEL_HIGH 7>;
+				status = "disabled";
+			};
+
 			sckc@f8048050 {
 				compatible = "atmel,at91sam9x5-sckc";
 				reg = <0xf8048050 0x4>;

arch/arm/boot/dts/sama5d4.dtsi

@@ -451,7 +451,7 @@
 					interrupt-parent = <&pmc>;
 					interrupts = <AT91_PMC_MCKRDY>;
 					clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>;
-					atmel,clk-output-range = <125000000 177000000>;
+					atmel,clk-output-range = <125000000 200000000>;
 					atmel,clk-divisors = <1 2 4 3>;
 				};
 
@@ -916,7 +916,7 @@
 			};
 
 			i2c0: i2c@f8014000 {
-				compatible = "atmel,at91sam9x5-i2c";
+				compatible = "atmel,sama5d4-i2c";
 				reg = <0xf8014000 0x4000>;
 				interrupts = <32 IRQ_TYPE_LEVEL_HIGH 6>;
 				dmas = <&dma1
@@ -935,7 +935,7 @@
 			};
 
 			i2c1: i2c@f8018000 {
-				compatible = "atmel,at91sam9x5-i2c";
+				compatible = "atmel,sama5d4-i2c";
 				reg = <0xf8018000 0x4000>;
 				interrupts = <33 IRQ_TYPE_LEVEL_HIGH 6>;
 				dmas = <&dma1
@@ -975,7 +975,7 @@
 			};
 
 			i2c2: i2c@f8024000 {
-				compatible = "atmel,at91sam9x5-i2c";
+				compatible = "atmel,sama5d4-i2c";
 				reg = <0xf8024000 0x4000>;
 				interrupts = <34 IRQ_TYPE_LEVEL_HIGH 6>;
 				dmas = <&dma1
@@ -1669,15 +1669,23 @@
 					pinctrl_mmc0_clk_cmd_dat0: mmc0_clk_cmd_dat0 {
 						atmel,pins =
 							<AT91_PIOC 4 AT91_PERIPH_B AT91_PINCTRL_NONE	/* MCI0_CK, conflict with PCK1(ISI_MCK) */
-							 AT91_PIOC 5 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* MCI0_CDB, conflict with NAND_D0 */
-							 AT91_PIOC 6 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* MCI0_DB0, conflict with NAND_D1 */
+							 AT91_PIOC 5 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* MCI0_CDA, conflict with NAND_D0 */
+							 AT91_PIOC 6 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* MCI0_DA0, conflict with NAND_D1 */
 							>;
 					};
 					pinctrl_mmc0_dat1_3: mmc0_dat1_3 {
 						atmel,pins =
-							<AT91_PIOC 7 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* MCI0_DB1, conflict with NAND_D2 */
-							 AT91_PIOC 8 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* MCI0_DB2, conflict with NAND_D3 */
-							 AT91_PIOC 9 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* MCI0_DB3, conflict with NAND_D4 */
+							<AT91_PIOC 7 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* MCI0_DA1, conflict with NAND_D2 */
+							 AT91_PIOC 8 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* MCI0_DA2, conflict with NAND_D3 */
+							 AT91_PIOC 9 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* MCI0_DA3, conflict with NAND_D4 */
+							>;
+					};
+					pinctrl_mmc0_dat4_7: mmc0_dat4_7 {
+						atmel,pins =
+							<AT91_PIOC 10 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* MCI0_DA4, conflict with NAND_D5 */
+							 AT91_PIOC 11 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* MCI0_DA5, conflict with NAND_D6 */
+							 AT91_PIOC 12 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* MCI0_DA6, conflict with NAND_D7 */
+							 AT91_PIOC 13 AT91_PERIPH_B AT91_PINCTRL_PULL_UP	/* MCI0_DA7, conflict with NAND_OE */
 							>;
 					};
 				};