Merge tag 'mailbox-v4.19' of git://git.linaro.org/landing-teams/working/fujitsu/integration

Pull mailbox updates from Jassi Brar:

 - xgene: potential null pointer fix

 - omap: switch to spdx license and use of_device_get_match_data() to
   match data

 - ti-msgmgr: cleanup and optimisation. New TI specific feature - secure
   proxy thread.

 - mediatek: add driver for CMDQ controller.

 - nxp: add driver for MU controller

* tag 'mailbox-v4.19' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
  mailbox: Add support for i.MX messaging unit
  dt-bindings: mailbox: imx-mu: add generic MU channel support
  dt-bindings: arm: fsl: add mu binding doc
  mailbox: add MODULE_LICENSE() for mtk-cmdq-mailbox.c
  mailbox: mediatek: Add Mediatek CMDQ driver
  dt-bindings: soc: Add documentation for the MediaTek GCE unit
  mailbox: ti-msgmgr: Add support for Secure Proxy
  dt-bindings: mailbox: Add support for secure proxy threads
  mailbox: ti-msgmgr: Move the memory region name to descriptor
  mailbox: ti-msgmgr: Change message count mask to be descriptor based
  mailbox: ti-msgmgr: Allocate Rx channel resources only on request
  mailbox: ti-msgmgr: Get rid of unused structure members
  mailbox/omap: use of_device_get_match_data() to get match data
  mailbox/omap: switch to SPDX license identifier
  mailbox: xgene-slimpro: Fix potential NULL pointer dereference

Documentation/devicetree/bindings/mailbox/fsl,mu.txt

@@ -0,0 +1,54 @@
+NXP i.MX Messaging Unit (MU)
+--------------------------------------------------------------------
+
+The Messaging Unit module enables two processors within the SoC to
+communicate and coordinate by passing messages (e.g. data, status
+and control) through the MU interface. The MU also provides the ability
+for one processor to signal the other processor using interrupts.
+
+Because the MU manages the messaging between processors, the MU uses
+different clocks (from each side of the different peripheral buses).
+Therefore, the MU must synchronize the accesses from one side to the
+other. The MU accomplishes synchronization using two sets of matching
+registers (Processor A-facing, Processor B-facing).
+
+Messaging Unit Device Node:
+=============================
+
+Required properties:
+-------------------
+- compatible :	should be "fsl,<chip>-mu", the supported chips include
+		imx6sx, imx7s, imx8qxp, imx8qm.
+		The "fsl,imx6sx-mu" compatible is seen as generic and should
+		be included together with SoC specific compatible.
+- reg :		Should contain the registers location and length
+- interrupts :	Interrupt number. The interrupt specifier format depends
+		on the interrupt controller parent.
+- #mbox-cells:  Must be 2.
+			  <&phandle type channel>
+			    phandle   : Label name of controller
+			    type      : Channel type
+			    channel   : Channel number
+
+		This MU support 4 type of unidirectional channels, each type
+		has 4 channels. A total of 16 channels. Following types are
+		supported:
+		0 - TX channel with 32bit transmit register and IRQ transmit
+		acknowledgment support.
+		1 - RX channel with 32bit receive register and IRQ support
+		2 - TX doorbell channel. Without own register and no ACK support.
+		3 - RX doorbell channel.
+
+Optional properties:
+-------------------
+- clocks :	phandle to the input clock.
+- fsl,mu-side-b : Should be set for side B MU.
+
+Examples:
+--------
+lsio_mu0: mailbox@5d1b0000 {
+	compatible = "fsl,imx8qxp-mu";
+	reg = <0x0 0x5d1b0000 0x0 0x10000>;
+	interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+	#mbox-cells = <2>;
+};

Documentation/devicetree/bindings/mailbox/mtk-gce.txt

@@ -0,0 +1,57 @@
+MediaTek GCE
+===============
+
+The Global Command Engine (GCE) is used to help read/write registers with
+critical time limitation, such as updating display configuration during the
+vblank. The GCE can be used to implement the Command Queue (CMDQ) driver.
+
+CMDQ driver uses mailbox framework for communication. Please refer to
+mailbox.txt for generic information about mailbox device-tree bindings.
+
+Required properties:
+- compatible: Must be "mediatek,mt8173-gce"
+- reg: Address range of the GCE unit
+- interrupts: The interrupt signal from the GCE block
+- clock: Clocks according to the common clock binding
+- clock-names: Must be "gce" to stand for GCE clock
+- #mbox-cells: Should be 3.
+	<&phandle channel priority atomic_exec>
+	phandle: Label name of a gce node.
+	channel: Channel of mailbox. Be equal to the thread id of GCE.
+	priority: Priority of GCE thread.
+	atomic_exec: GCE processing continuous packets of commands in atomic
+		way.
+
+Required properties for a client device:
+- mboxes: Client use mailbox to communicate with GCE, it should have this
+  property and list of phandle, mailbox specifiers.
+- mediatek,gce-subsys: u32, specify the sub-system id which is corresponding
+  to the register address.
+
+Some vaules of properties are defined in 'dt-bindings/gce/mt8173-gce.h'. Such as
+sub-system ids, thread priority, event ids.
+
+Example:
+
+	gce: gce@10212000 {
+		compatible = "mediatek,mt8173-gce";
+		reg = <0 0x10212000 0 0x1000>;
+		interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&infracfg CLK_INFRA_GCE>;
+		clock-names = "gce";
+		thread-num = CMDQ_THR_MAX_COUNT;
+		#mbox-cells = <3>;
+	};
+
+Example for a client device:
+
+	mmsys: clock-controller@14000000 {
+		compatible = "mediatek,mt8173-mmsys";
+		mboxes = <&gce 0 CMDQ_THR_PRIO_LOWEST 1>,
+			 <&gce 1 CMDQ_THR_PRIO_LOWEST 1>;
+		mediatek,gce-subsys = <SUBSYS_1400XXXX>;
+		mutex-event-eof = <CMDQ_EVENT_MUTEX0_STREAM_EOF
+				CMDQ_EVENT_MUTEX1_STREAM_EOF>;
+
+		...
+	};

Documentation/devicetree/bindings/mailbox/ti,secure-proxy.txt

@@ -0,0 +1,50 @@
+Texas Instruments' Secure Proxy
+========================================
+
+The Texas Instruments' secure proxy is a mailbox controller that has
+configurable queues selectable at SoC(System on Chip) integration. The
+Message manager is broken up into different address regions that are
+called "threads" or "proxies" - each instance is unidirectional and is
+instantiated at SoC integration level by system controller to indicate
+receive or transmit path.
+
+Message Manager Device Node:
+===========================
+Required properties:
+--------------------
+- compatible:		Shall be "ti,am654-secure-proxy"
+- reg-names 		target_data - Map the proxy data region
+			rt - Map the realtime status region
+			scfg - Map the configuration region
+- reg:			Contains the register map per reg-names.
+- #mbox-cells		Shall be 1 and shall refer to the transfer path
+			called thread.
+- interrupt-names:	Contains interrupt names matching the rx transfer path
+			for a given SoC. Receive interrupts shall be of the
+			format: "rx_<PID>".
+- interrupts:		Contains the interrupt information corresponding to
+			interrupt-names property.
+
+Example(AM654):
+------------
+
+	secure_proxy: mailbox@32c00000 {
+		compatible = "ti,am654-secure-proxy";
+		#mbox-cells = <1>;
+		reg-names = "target_data", "rt", "scfg";
+		reg = <0x0 0x32c00000 0x0 0x100000>,
+		      <0x0 0x32400000 0x0 0x100000>,
+		      <0x0 0x32800000 0x0 0x100000>;
+		interrupt-names = "rx_011";
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	dmsc: dmsc {
+		[...]
+		mbox-names = "rx", "tx";
+		# RX Thread ID is 11
+		# TX Thread ID is 13
+		mboxes= <&secure_proxy 11>,
+			<&secure_proxy 13>;
+		[...]
+	};

drivers/mailbox/Kconfig

@@ -15,6 +15,12 @@ config ARM_MHU
 	  The controller has 3 mailbox channels, the last of which can be
 	  used in Secure mode only.
 
+config IMX_MBOX
+	tristate "i.MX Mailbox"
+	depends on ARCH_MXC || COMPILE_TEST
+	help
+	  Mailbox implementation for i.MX Messaging Unit (MU).
+
 config PLATFORM_MHU
 	tristate "Platform MHU Mailbox"
 	depends on OF
@@ -189,4 +195,14 @@ config STM32_IPCC
 	  Mailbox implementation for STMicroelectonics STM32 family chips
 	  with hardware for Inter-Processor Communication Controller (IPCC)
 	  between processors. Say Y here if you want to have this support.
+
+config MTK_CMDQ_MBOX
+	tristate "MediaTek CMDQ Mailbox Support"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
+	select MTK_INFRACFG
+	help
+	  Say yes here to add support for the MediaTek Command Queue (CMDQ)
+	  mailbox driver. The CMDQ is used to help read/write registers with
+	  critical time limitation, such as updating display configuration
+	  during the vblank.
 endif

drivers/mailbox/Makefile

@@ -7,6 +7,8 @@ obj-$(CONFIG_MAILBOX_TEST)	+= mailbox-test.o
 
 obj-$(CONFIG_ARM_MHU)	+= arm_mhu.o
 
+obj-$(CONFIG_IMX_MBOX)	+= imx-mailbox.o
+
 obj-$(CONFIG_PLATFORM_MHU)	+= platform_mhu.o
 
 obj-$(CONFIG_PL320_MBOX)	+= pl320-ipc.o
@@ -40,3 +42,5 @@ obj-$(CONFIG_QCOM_APCS_IPC)	+= qcom-apcs-ipc-mailbox.o
 obj-$(CONFIG_TEGRA_HSP_MBOX)	+= tegra-hsp.o
 
 obj-$(CONFIG_STM32_IPCC) 	+= stm32-ipcc.o
+
+obj-$(CONFIG_MTK_CMDQ_MBOX)	+= mtk-cmdq-mailbox.o

drivers/mailbox/imx-mailbox.c

@@ -0,0 +1,358 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018 Pengutronix, Oleksij Rempel <o.rempel@pengutronix.de>
+ */
+
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mailbox_controller.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/slab.h>
+
+/* Transmit Register */
+#define IMX_MU_xTRn(x)		(0x00 + 4 * (x))
+/* Receive Register */
+#define IMX_MU_xRRn(x)		(0x10 + 4 * (x))
+/* Status Register */
+#define IMX_MU_xSR		0x20
+#define IMX_MU_xSR_GIPn(x)	BIT(28 + (3 - (x)))
+#define IMX_MU_xSR_RFn(x)	BIT(24 + (3 - (x)))
+#define IMX_MU_xSR_TEn(x)	BIT(20 + (3 - (x)))
+#define IMX_MU_xSR_BRDIP	BIT(9)
+
+/* Control Register */
+#define IMX_MU_xCR		0x24
+/* General Purpose Interrupt Enable */
+#define IMX_MU_xCR_GIEn(x)	BIT(28 + (3 - (x)))
+/* Receive Interrupt Enable */
+#define IMX_MU_xCR_RIEn(x)	BIT(24 + (3 - (x)))
+/* Transmit Interrupt Enable */
+#define IMX_MU_xCR_TIEn(x)	BIT(20 + (3 - (x)))
+/* General Purpose Interrupt Request */
+#define IMX_MU_xCR_GIRn(x)	BIT(16 + (3 - (x)))
+
+#define IMX_MU_CHANS		16
+#define IMX_MU_CHAN_NAME_SIZE	20
+
+enum imx_mu_chan_type {
+	IMX_MU_TYPE_TX,		/* Tx */
+	IMX_MU_TYPE_RX,		/* Rx */
+	IMX_MU_TYPE_TXDB,	/* Tx doorbell */
+	IMX_MU_TYPE_RXDB,	/* Rx doorbell */
+};
+
+struct imx_mu_con_priv {
+	unsigned int		idx;
+	char			irq_desc[IMX_MU_CHAN_NAME_SIZE];
+	enum imx_mu_chan_type	type;
+	struct mbox_chan	*chan;
+	struct tasklet_struct	txdb_tasklet;
+};
+
+struct imx_mu_priv {
+	struct device		*dev;
+	void __iomem		*base;
+	spinlock_t		xcr_lock; /* control register lock */
+
+	struct mbox_controller	mbox;
+	struct mbox_chan	mbox_chans[IMX_MU_CHANS];
+
+	struct imx_mu_con_priv  con_priv[IMX_MU_CHANS];
+	struct clk		*clk;
+	int			irq;
+
+	bool			side_b;
+};
+
+static struct imx_mu_priv *to_imx_mu_priv(struct mbox_controller *mbox)
+{
+	return container_of(mbox, struct imx_mu_priv, mbox);
+}
+
+static void imx_mu_write(struct imx_mu_priv *priv, u32 val, u32 offs)
+{
+	iowrite32(val, priv->base + offs);
+}
+
+static u32 imx_mu_read(struct imx_mu_priv *priv, u32 offs)
+{
+	return ioread32(priv->base + offs);
+}
+
+static u32 imx_mu_xcr_rmw(struct imx_mu_priv *priv, u32 set, u32 clr)
+{
+	unsigned long flags;
+	u32 val;
+
+	spin_lock_irqsave(&priv->xcr_lock, flags);
+	val = imx_mu_read(priv, IMX_MU_xCR);
+	val &= ~clr;
+	val |= set;
+	imx_mu_write(priv, val, IMX_MU_xCR);
+	spin_unlock_irqrestore(&priv->xcr_lock, flags);
+
+	return val;
+}
+
+static void imx_mu_txdb_tasklet(unsigned long data)
+{
+	struct imx_mu_con_priv *cp = (struct imx_mu_con_priv *)data;
+
+	mbox_chan_txdone(cp->chan, 0);
+}
+
+static irqreturn_t imx_mu_isr(int irq, void *p)
+{
+	struct mbox_chan *chan = p;
+	struct imx_mu_priv *priv = to_imx_mu_priv(chan->mbox);
+	struct imx_mu_con_priv *cp = chan->con_priv;
+	u32 val, ctrl, dat;
+
+	ctrl = imx_mu_read(priv, IMX_MU_xCR);
+	val = imx_mu_read(priv, IMX_MU_xSR);
+
+	switch (cp->type) {
+	case IMX_MU_TYPE_TX:
+		val &= IMX_MU_xSR_TEn(cp->idx) &
+			(ctrl & IMX_MU_xCR_TIEn(cp->idx));
+		break;
+	case IMX_MU_TYPE_RX:
+		val &= IMX_MU_xSR_RFn(cp->idx) &
+			(ctrl & IMX_MU_xCR_RIEn(cp->idx));
+		break;
+	case IMX_MU_TYPE_RXDB:
+		val &= IMX_MU_xSR_GIPn(cp->idx) &
+			(ctrl & IMX_MU_xCR_GIEn(cp->idx));
+		break;
+	default:
+		break;
+	}
+
+	if (!val)
+		return IRQ_NONE;
+
+	if (val == IMX_MU_xSR_TEn(cp->idx)) {
+		imx_mu_xcr_rmw(priv, 0, IMX_MU_xCR_TIEn(cp->idx));
+		mbox_chan_txdone(chan, 0);
+	} else if (val == IMX_MU_xSR_RFn(cp->idx)) {
+		dat = imx_mu_read(priv, IMX_MU_xRRn(cp->idx));
+		mbox_chan_received_data(chan, (void *)&dat);
+	} else if (val == IMX_MU_xSR_GIPn(cp->idx)) {
+		imx_mu_write(priv, IMX_MU_xSR_GIPn(cp->idx), IMX_MU_xSR);
+		mbox_chan_received_data(chan, NULL);
+	} else {
+		dev_warn_ratelimited(priv->dev, "Not handled interrupt\n");
+		return IRQ_NONE;
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int imx_mu_send_data(struct mbox_chan *chan, void *data)
+{
+	struct imx_mu_priv *priv = to_imx_mu_priv(chan->mbox);
+	struct imx_mu_con_priv *cp = chan->con_priv;
+	u32 *arg = data;
+
+	switch (cp->type) {
+	case IMX_MU_TYPE_TX:
+		imx_mu_write(priv, *arg, IMX_MU_xTRn(cp->idx));
+		imx_mu_xcr_rmw(priv, IMX_MU_xCR_TIEn(cp->idx), 0);
+		break;
+	case IMX_MU_TYPE_TXDB:
+		imx_mu_xcr_rmw(priv, IMX_MU_xCR_GIRn(cp->idx), 0);
+		tasklet_schedule(&cp->txdb_tasklet);
+		break;
+	default:
+		dev_warn_ratelimited(priv->dev, "Send data on wrong channel type: %d\n", cp->type);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int imx_mu_startup(struct mbox_chan *chan)
+{
+	struct imx_mu_priv *priv = to_imx_mu_priv(chan->mbox);
+	struct imx_mu_con_priv *cp = chan->con_priv;
+	int ret;
+
+	if (cp->type == IMX_MU_TYPE_TXDB) {
+		/* Tx doorbell don't have ACK support */
+		tasklet_init(&cp->txdb_tasklet, imx_mu_txdb_tasklet,
+			     (unsigned long)cp);
+		return 0;
+	}
+
+	ret = request_irq(priv->irq, imx_mu_isr, IRQF_SHARED, cp->irq_desc,
+			  chan);
+	if (ret) {
+		dev_err(priv->dev,
+			"Unable to acquire IRQ %d\n", priv->irq);
+		return ret;
+	}
+
+	switch (cp->type) {
+	case IMX_MU_TYPE_RX:
+		imx_mu_xcr_rmw(priv, IMX_MU_xCR_RIEn(cp->idx), 0);
+		break;
+	case IMX_MU_TYPE_RXDB:
+		imx_mu_xcr_rmw(priv, IMX_MU_xCR_GIEn(cp->idx), 0);
+		break;
+	default:
+		break;
+	}
+
+	return 0;
+}
+
+static void imx_mu_shutdown(struct mbox_chan *chan)
+{
+	struct imx_mu_priv *priv = to_imx_mu_priv(chan->mbox);
+	struct imx_mu_con_priv *cp = chan->con_priv;
+
+	if (cp->type == IMX_MU_TYPE_TXDB)
+		tasklet_kill(&cp->txdb_tasklet);
+
+	imx_mu_xcr_rmw(priv, 0,
+		   IMX_MU_xCR_TIEn(cp->idx) | IMX_MU_xCR_RIEn(cp->idx));
+
+	free_irq(priv->irq, chan);
+}
+
+static const struct mbox_chan_ops imx_mu_ops = {
+	.send_data = imx_mu_send_data,
+	.startup = imx_mu_startup,
+	.shutdown = imx_mu_shutdown,
+};
+
+static struct mbox_chan * imx_mu_xlate(struct mbox_controller *mbox,
+				       const struct of_phandle_args *sp)
+{
+	u32 type, idx, chan;
+
+	if (sp->args_count != 2) {
+		dev_err(mbox->dev, "Invalid argument count %d\n", sp->args_count);
+		return ERR_PTR(-EINVAL);
+	}
+
+	type = sp->args[0]; /* channel type */
+	idx = sp->args[1]; /* index */
+	chan = type * 4 + idx;
+
+	if (chan >= mbox->num_chans) {
+		dev_err(mbox->dev, "Not supported channel number: %d. (type: %d, idx: %d)\n", chan, type, idx);
+		return ERR_PTR(-EINVAL);
+	}
+
+	return &mbox->chans[chan];
+}
+
+static void imx_mu_init_generic(struct imx_mu_priv *priv)
+{
+	if (priv->side_b)
+		return;
+
+	/* Set default MU configuration */
+	imx_mu_write(priv, 0, IMX_MU_xCR);
+}
+
+static int imx_mu_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct resource *iomem;
+	struct imx_mu_priv *priv;
+	unsigned int i;
+	int ret;
+
+	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = dev;
+
+	iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	priv->base = devm_ioremap_resource(&pdev->dev, iomem);
+	if (IS_ERR(priv->base))
+		return PTR_ERR(priv->base);
+
+	priv->irq = platform_get_irq(pdev, 0);
+	if (priv->irq < 0)
+		return priv->irq;
+
+	priv->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(priv->clk)) {
+		if (PTR_ERR(priv->clk) != -ENOENT)
+			return PTR_ERR(priv->clk);
+
+		priv->clk = NULL;
+	}
+
+	ret = clk_prepare_enable(priv->clk);
+	if (ret) {
+		dev_err(dev, "Failed to enable clock\n");
+		return ret;
+	}
+
+	for (i = 0; i < IMX_MU_CHANS; i++) {
+		struct imx_mu_con_priv *cp = &priv->con_priv[i];
+
+		cp->idx = i % 4;
+		cp->type = i >> 2;
+		cp->chan = &priv->mbox_chans[i];
+		priv->mbox_chans[i].con_priv = cp;
+		snprintf(cp->irq_desc, sizeof(cp->irq_desc),
+			 "imx_mu_chan[%i-%i]", cp->type, cp->idx);
+	}
+
+	priv->side_b = of_property_read_bool(np, "fsl,mu-side-b");
+
+	spin_lock_init(&priv->xcr_lock);
+
+	priv->mbox.dev = dev;
+	priv->mbox.ops = &imx_mu_ops;
+	priv->mbox.chans = priv->mbox_chans;
+	priv->mbox.num_chans = IMX_MU_CHANS;
+	priv->mbox.of_xlate = imx_mu_xlate;
+	priv->mbox.txdone_irq = true;
+
+	platform_set_drvdata(pdev, priv);
+
+	imx_mu_init_generic(priv);
+
+	return mbox_controller_register(&priv->mbox);
+}
+
+static int imx_mu_remove(struct platform_device *pdev)
+{
+	struct imx_mu_priv *priv = platform_get_drvdata(pdev);
+
+	mbox_controller_unregister(&priv->mbox);
+	clk_disable_unprepare(priv->clk);
+
+	return 0;
+}
+
+static const struct of_device_id imx_mu_dt_ids[] = {
+	{ .compatible = "fsl,imx6sx-mu" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, imx_mu_dt_ids);
+
+static struct platform_driver imx_mu_driver = {
+	.probe		= imx_mu_probe,
+	.remove		= imx_mu_remove,
+	.driver = {
+		.name	= "imx_mu",
+		.of_match_table = imx_mu_dt_ids,
+	},
+};
+module_platform_driver(imx_mu_driver);
+
+MODULE_AUTHOR("Oleksij Rempel <o.rempel@pengutronix.de>");
+MODULE_DESCRIPTION("Message Unit driver for i.MX");
+MODULE_LICENSE("GPL v2");

drivers/mailbox/mailbox-xgene-slimpro.c

@@ -195,9 +195,9 @@ static int slimpro_mbox_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, ctx);
 
 	regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	mb_base = devm_ioremap(&pdev->dev, regs->start, resource_size(regs));
-	if (!mb_base)
-		return -ENOMEM;
+	mb_base = devm_ioremap_resource(&pdev->dev, regs);
+	if (IS_ERR(mb_base))
+		return PTR_ERR(mb_base);
 
 	/* Setup mailbox links */
 	for (i = 0; i < MBOX_CNT; i++) {

drivers/mailbox/mtk-cmdq-mailbox.c

@@ -0,0 +1,571 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (c) 2018 MediaTek Inc.
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/dma-mapping.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/mailbox_controller.h>
+#include <linux/mailbox/mtk-cmdq-mailbox.h>
+#include <linux/of_device.h>
+
+#define CMDQ_OP_CODE_MASK		(0xff << CMDQ_OP_CODE_SHIFT)
+#define CMDQ_IRQ_MASK			0xffff
+#define CMDQ_NUM_CMD(t)			(t->cmd_buf_size / CMDQ_INST_SIZE)
+
+#define CMDQ_CURR_IRQ_STATUS		0x10
+#define CMDQ_THR_SLOT_CYCLES		0x30
+#define CMDQ_THR_BASE			0x100
+#define CMDQ_THR_SIZE			0x80
+#define CMDQ_THR_WARM_RESET		0x00
+#define CMDQ_THR_ENABLE_TASK		0x04
+#define CMDQ_THR_SUSPEND_TASK		0x08
+#define CMDQ_THR_CURR_STATUS		0x0c
+#define CMDQ_THR_IRQ_STATUS		0x10
+#define CMDQ_THR_IRQ_ENABLE		0x14
+#define CMDQ_THR_CURR_ADDR		0x20
+#define CMDQ_THR_END_ADDR		0x24
+#define CMDQ_THR_WAIT_TOKEN		0x30
+#define CMDQ_THR_PRIORITY		0x40
+
+#define CMDQ_THR_ACTIVE_SLOT_CYCLES	0x3200
+#define CMDQ_THR_ENABLED		0x1
+#define CMDQ_THR_DISABLED		0x0
+#define CMDQ_THR_SUSPEND		0x1
+#define CMDQ_THR_RESUME			0x0
+#define CMDQ_THR_STATUS_SUSPENDED	BIT(1)
+#define CMDQ_THR_DO_WARM_RESET		BIT(0)
+#define CMDQ_THR_IRQ_DONE		0x1
+#define CMDQ_THR_IRQ_ERROR		0x12
+#define CMDQ_THR_IRQ_EN			(CMDQ_THR_IRQ_ERROR | CMDQ_THR_IRQ_DONE)
+#define CMDQ_THR_IS_WAITING		BIT(31)
+
+#define CMDQ_JUMP_BY_OFFSET		0x10000000
+#define CMDQ_JUMP_BY_PA			0x10000001
+
+struct cmdq_thread {
+	struct mbox_chan	*chan;
+	void __iomem		*base;
+	struct list_head	task_busy_list;
+	u32			priority;
+	bool			atomic_exec;
+};
+
+struct cmdq_task {
+	struct cmdq		*cmdq;
+	struct list_head	list_entry;
+	dma_addr_t		pa_base;
+	struct cmdq_thread	*thread;
+	struct cmdq_pkt		*pkt; /* the packet sent from mailbox client */
+};
+
+struct cmdq {
+	struct mbox_controller	mbox;
+	void __iomem		*base;
+	u32			irq;
+	u32			thread_nr;
+	struct cmdq_thread	*thread;
+	struct clk		*clock;
+	bool			suspended;
+};
+
+static int cmdq_thread_suspend(struct cmdq *cmdq, struct cmdq_thread *thread)
+{
+	u32 status;
+
+	writel(CMDQ_THR_SUSPEND, thread->base + CMDQ_THR_SUSPEND_TASK);
+
+	/* If already disabled, treat as suspended successful. */
+	if (!(readl(thread->base + CMDQ_THR_ENABLE_TASK) & CMDQ_THR_ENABLED))
+		return 0;
+
+	if (readl_poll_timeout_atomic(thread->base + CMDQ_THR_CURR_STATUS,
+			status, status & CMDQ_THR_STATUS_SUSPENDED, 0, 10)) {
+		dev_err(cmdq->mbox.dev, "suspend GCE thread 0x%x failed\n",
+			(u32)(thread->base - cmdq->base));
+		return -EFAULT;
+	}
+
+	return 0;
+}
+
+static void cmdq_thread_resume(struct cmdq_thread *thread)
+{
+	writel(CMDQ_THR_RESUME, thread->base + CMDQ_THR_SUSPEND_TASK);
+}
+
+static void cmdq_init(struct cmdq *cmdq)
+{
+	WARN_ON(clk_enable(cmdq->clock) < 0);
+	writel(CMDQ_THR_ACTIVE_SLOT_CYCLES, cmdq->base + CMDQ_THR_SLOT_CYCLES);
+	clk_disable(cmdq->clock);
+}
+
+static int cmdq_thread_reset(struct cmdq *cmdq, struct cmdq_thread *thread)
+{
+	u32 warm_reset;
+
+	writel(CMDQ_THR_DO_WARM_RESET, thread->base + CMDQ_THR_WARM_RESET);
+	if (readl_poll_timeout_atomic(thread->base + CMDQ_THR_WARM_RESET,
+			warm_reset, !(warm_reset & CMDQ_THR_DO_WARM_RESET),
+			0, 10)) {
+		dev_err(cmdq->mbox.dev, "reset GCE thread 0x%x failed\n",
+			(u32)(thread->base - cmdq->base));
+		return -EFAULT;
+	}
+
+	return 0;
+}
+
+static void cmdq_thread_disable(struct cmdq *cmdq, struct cmdq_thread *thread)
+{
+	cmdq_thread_reset(cmdq, thread);
+	writel(CMDQ_THR_DISABLED, thread->base + CMDQ_THR_ENABLE_TASK);
+}
+
+/* notify GCE to re-fetch commands by setting GCE thread PC */
+static void cmdq_thread_invalidate_fetched_data(struct cmdq_thread *thread)
+{
+	writel(readl(thread->base + CMDQ_THR_CURR_ADDR),
+	       thread->base + CMDQ_THR_CURR_ADDR);
+}
+
+static void cmdq_task_insert_into_thread(struct cmdq_task *task)
+{
+	struct device *dev = task->cmdq->mbox.dev;
+	struct cmdq_thread *thread = task->thread;
+	struct cmdq_task *prev_task = list_last_entry(
+			&thread->task_busy_list, typeof(*task), list_entry);
+	u64 *prev_task_base = prev_task->pkt->va_base;
+
+	/* let previous task jump to this task */
+	dma_sync_single_for_cpu(dev, prev_task->pa_base,
+				prev_task->pkt->cmd_buf_size, DMA_TO_DEVICE);
+	prev_task_base[CMDQ_NUM_CMD(prev_task->pkt) - 1] =
+		(u64)CMDQ_JUMP_BY_PA << 32 | task->pa_base;
+	dma_sync_single_for_device(dev, prev_task->pa_base,
+				   prev_task->pkt->cmd_buf_size, DMA_TO_DEVICE);
+
+	cmdq_thread_invalidate_fetched_data(thread);
+}
+
+static bool cmdq_command_is_wfe(u64 cmd)
+{
+	u64 wfe_option = CMDQ_WFE_UPDATE | CMDQ_WFE_WAIT | CMDQ_WFE_WAIT_VALUE;
+	u64 wfe_op = (u64)(CMDQ_CODE_WFE << CMDQ_OP_CODE_SHIFT) << 32;
+	u64 wfe_mask = (u64)CMDQ_OP_CODE_MASK << 32 | 0xffffffff;
+
+	return ((cmd & wfe_mask) == (wfe_op | wfe_option));
+}
+
+/* we assume tasks in the same display GCE thread are waiting the same event. */
+static void cmdq_task_remove_wfe(struct cmdq_task *task)
+{
+	struct device *dev = task->cmdq->mbox.dev;
+	u64 *base = task->pkt->va_base;
+	int i;
+
+	dma_sync_single_for_cpu(dev, task->pa_base, task->pkt->cmd_buf_size,
+				DMA_TO_DEVICE);
+	for (i = 0; i < CMDQ_NUM_CMD(task->pkt); i++)
+		if (cmdq_command_is_wfe(base[i]))
+			base[i] = (u64)CMDQ_JUMP_BY_OFFSET << 32 |
+				  CMDQ_JUMP_PASS;
+	dma_sync_single_for_device(dev, task->pa_base, task->pkt->cmd_buf_size,
+				   DMA_TO_DEVICE);
+}
+
+static bool cmdq_thread_is_in_wfe(struct cmdq_thread *thread)
+{
+	return readl(thread->base + CMDQ_THR_WAIT_TOKEN) & CMDQ_THR_IS_WAITING;
+}
+
+static void cmdq_thread_wait_end(struct cmdq_thread *thread,
+				 unsigned long end_pa)
+{
+	struct device *dev = thread->chan->mbox->dev;
+	unsigned long curr_pa;
+
+	if (readl_poll_timeout_atomic(thread->base + CMDQ_THR_CURR_ADDR,
+			curr_pa, curr_pa == end_pa, 1, 20))
+		dev_err(dev, "GCE thread cannot run to end.\n");
+}
+
+static void cmdq_task_exec_done(struct cmdq_task *task, enum cmdq_cb_status sta)
+{
+	struct cmdq_task_cb *cb = &task->pkt->async_cb;
+	struct cmdq_cb_data data;
+
+	WARN_ON(cb->cb == (cmdq_async_flush_cb)NULL);
+	data.sta = sta;
+	data.data = cb->data;
+	cb->cb(data);
+
+	list_del(&task->list_entry);
+}
+
+static void cmdq_task_handle_error(struct cmdq_task *task)
+{
+	struct cmdq_thread *thread = task->thread;
+	struct cmdq_task *next_task;
+
+	dev_err(task->cmdq->mbox.dev, "task 0x%p error\n", task);
+	WARN_ON(cmdq_thread_suspend(task->cmdq, thread) < 0);
+	next_task = list_first_entry_or_null(&thread->task_busy_list,
+			struct cmdq_task, list_entry);
+	if (next_task)
+		writel(next_task->pa_base, thread->base + CMDQ_THR_CURR_ADDR);
+	cmdq_thread_resume(thread);
+}
+
+static void cmdq_thread_irq_handler(struct cmdq *cmdq,
+				    struct cmdq_thread *thread)
+{
+	struct cmdq_task *task, *tmp, *curr_task = NULL;
+	u32 curr_pa, irq_flag, task_end_pa;
+	bool err;
+
+	irq_flag = readl(thread->base + CMDQ_THR_IRQ_STATUS);
+	writel(~irq_flag, thread->base + CMDQ_THR_IRQ_STATUS);
+
+	/*
+	 * When ISR call this function, another CPU core could run
+	 * "release task" right before we acquire the spin lock, and thus
+	 * reset / disable this GCE thread, so we need to check the enable
+	 * bit of this GCE thread.
+	 */
+	if (!(readl(thread->base + CMDQ_THR_ENABLE_TASK) & CMDQ_THR_ENABLED))
+		return;
+
+	if (irq_flag & CMDQ_THR_IRQ_ERROR)
+		err = true;
+	else if (irq_flag & CMDQ_THR_IRQ_DONE)
+		err = false;
+	else
+		return;
+
+	curr_pa = readl(thread->base + CMDQ_THR_CURR_ADDR);
+
+	list_for_each_entry_safe(task, tmp, &thread->task_busy_list,
+				 list_entry) {
+		task_end_pa = task->pa_base + task->pkt->cmd_buf_size;
+		if (curr_pa >= task->pa_base && curr_pa < task_end_pa)
+			curr_task = task;
+
+		if (!curr_task || curr_pa == task_end_pa - CMDQ_INST_SIZE) {
+			cmdq_task_exec_done(task, CMDQ_CB_NORMAL);
+			kfree(task);
+		} else if (err) {
+			cmdq_task_exec_done(task, CMDQ_CB_ERROR);
+			cmdq_task_handle_error(curr_task);
+			kfree(task);
+		}
+
+		if (curr_task)
+			break;
+	}
+
+	if (list_empty(&thread->task_busy_list)) {
+		cmdq_thread_disable(cmdq, thread);
+		clk_disable(cmdq->clock);
+	}
+}
+
+static irqreturn_t cmdq_irq_handler(int irq, void *dev)
+{
+	struct cmdq *cmdq = dev;
+	unsigned long irq_status, flags = 0L;
+	int bit;
+
+	irq_status = readl(cmdq->base + CMDQ_CURR_IRQ_STATUS) & CMDQ_IRQ_MASK;
+	if (!(irq_status ^ CMDQ_IRQ_MASK))
+		return IRQ_NONE;
+
+	for_each_clear_bit(bit, &irq_status, fls(CMDQ_IRQ_MASK)) {
+		struct cmdq_thread *thread = &cmdq->thread[bit];
+
+		spin_lock_irqsave(&thread->chan->lock, flags);
+		cmdq_thread_irq_handler(cmdq, thread);
+		spin_unlock_irqrestore(&thread->chan->lock, flags);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int cmdq_suspend(struct device *dev)
+{
+	struct cmdq *cmdq = dev_get_drvdata(dev);
+	struct cmdq_thread *thread;
+	int i;
+	bool task_running = false;
+
+	cmdq->suspended = true;
+
+	for (i = 0; i < cmdq->thread_nr; i++) {
+		thread = &cmdq->thread[i];
+		if (!list_empty(&thread->task_busy_list)) {
+			task_running = true;
+			break;
+		}
+	}
+
+	if (task_running)
+		dev_warn(dev, "exist running task(s) in suspend\n");
+
+	clk_unprepare(cmdq->clock);
+
+	return 0;
+}
+
+static int cmdq_resume(struct device *dev)
+{
+	struct cmdq *cmdq = dev_get_drvdata(dev);
+
+	WARN_ON(clk_prepare(cmdq->clock) < 0);
+	cmdq->suspended = false;
+	return 0;
+}
+
+static int cmdq_remove(struct platform_device *pdev)
+{
+	struct cmdq *cmdq = platform_get_drvdata(pdev);
+
+	mbox_controller_unregister(&cmdq->mbox);
+	clk_unprepare(cmdq->clock);
+
+	if (cmdq->mbox.chans)
+		devm_kfree(&pdev->dev, cmdq->mbox.chans);
+
+	if (cmdq->thread)
+		devm_kfree(&pdev->dev, cmdq->thread);
+
+	devm_kfree(&pdev->dev, cmdq);
+
+	return 0;
+}
+
+static int cmdq_mbox_send_data(struct mbox_chan *chan, void *data)
+{
+	struct cmdq_pkt *pkt = (struct cmdq_pkt *)data;
+	struct cmdq_thread *thread = (struct cmdq_thread *)chan->con_priv;
+	struct cmdq *cmdq = dev_get_drvdata(chan->mbox->dev);
+	struct cmdq_task *task;
+	unsigned long curr_pa, end_pa;
+
+	/* Client should not flush new tasks if suspended. */
+	WARN_ON(cmdq->suspended);
+
+	task = kzalloc(sizeof(*task), GFP_ATOMIC);
+	task->cmdq = cmdq;
+	INIT_LIST_HEAD(&task->list_entry);
+	task->pa_base = pkt->pa_base;
+	task->thread = thread;
+	task->pkt = pkt;
+
+	if (list_empty(&thread->task_busy_list)) {
+		WARN_ON(clk_enable(cmdq->clock) < 0);
+		WARN_ON(cmdq_thread_reset(cmdq, thread) < 0);
+
+		writel(task->pa_base, thread->base + CMDQ_THR_CURR_ADDR);
+		writel(task->pa_base + pkt->cmd_buf_size,
+		       thread->base + CMDQ_THR_END_ADDR);
+		writel(thread->priority, thread->base + CMDQ_THR_PRIORITY);
+		writel(CMDQ_THR_IRQ_EN, thread->base + CMDQ_THR_IRQ_ENABLE);
+		writel(CMDQ_THR_ENABLED, thread->base + CMDQ_THR_ENABLE_TASK);
+	} else {
+		WARN_ON(cmdq_thread_suspend(cmdq, thread) < 0);
+		curr_pa = readl(thread->base + CMDQ_THR_CURR_ADDR);
+		end_pa = readl(thread->base + CMDQ_THR_END_ADDR);
+
+		/*
+		 * Atomic execution should remove the following wfe, i.e. only
+		 * wait event at first task, and prevent to pause when running.
+		 */
+		if (thread->atomic_exec) {
+			/* GCE is executing if command is not WFE */
+			if (!cmdq_thread_is_in_wfe(thread)) {
+				cmdq_thread_resume(thread);
+				cmdq_thread_wait_end(thread, end_pa);
+				WARN_ON(cmdq_thread_suspend(cmdq, thread) < 0);
+				/* set to this task directly */
+				writel(task->pa_base,
+				       thread->base + CMDQ_THR_CURR_ADDR);
+			} else {
+				cmdq_task_insert_into_thread(task);
+				cmdq_task_remove_wfe(task);
+				smp_mb(); /* modify jump before enable thread */
+			}
+		} else {
+			/* check boundary */
+			if (curr_pa == end_pa - CMDQ_INST_SIZE ||
+			    curr_pa == end_pa) {
+				/* set to this task directly */
+				writel(task->pa_base,
+				       thread->base + CMDQ_THR_CURR_ADDR);
+			} else {
+				cmdq_task_insert_into_thread(task);
+				smp_mb(); /* modify jump before enable thread */
+			}
+		}
+		writel(task->pa_base + pkt->cmd_buf_size,
+		       thread->base + CMDQ_THR_END_ADDR);
+		cmdq_thread_resume(thread);
+	}
+	list_move_tail(&task->list_entry, &thread->task_busy_list);
+
+	return 0;
+}
+
+static int cmdq_mbox_startup(struct mbox_chan *chan)
+{
+	return 0;
+}
+
+static void cmdq_mbox_shutdown(struct mbox_chan *chan)
+{
+}
+
+static const struct mbox_chan_ops cmdq_mbox_chan_ops = {
+	.send_data = cmdq_mbox_send_data,
+	.startup = cmdq_mbox_startup,
+	.shutdown = cmdq_mbox_shutdown,
+};
+
+static struct mbox_chan *cmdq_xlate(struct mbox_controller *mbox,
+		const struct of_phandle_args *sp)
+{
+	int ind = sp->args[0];
+	struct cmdq_thread *thread;
+
+	if (ind >= mbox->num_chans)
+		return ERR_PTR(-EINVAL);
+
+	thread = (struct cmdq_thread *)mbox->chans[ind].con_priv;
+	thread->priority = sp->args[1];
+	thread->atomic_exec = (sp->args[2] != 0);
+	thread->chan = &mbox->chans[ind];
+
+	return &mbox->chans[ind];
+}
+
+static int cmdq_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	struct cmdq *cmdq;
+	int err, i;
+
+	cmdq = devm_kzalloc(dev, sizeof(*cmdq), GFP_KERNEL);
+	if (!cmdq)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	cmdq->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(cmdq->base)) {
+		dev_err(dev, "failed to ioremap gce\n");
+		return PTR_ERR(cmdq->base);
+	}
+
+	cmdq->irq = platform_get_irq(pdev, 0);
+	if (!cmdq->irq) {
+		dev_err(dev, "failed to get irq\n");
+		return -EINVAL;
+	}
+	err = devm_request_irq(dev, cmdq->irq, cmdq_irq_handler, IRQF_SHARED,
+			       "mtk_cmdq", cmdq);
+	if (err < 0) {
+		dev_err(dev, "failed to register ISR (%d)\n", err);
+		return err;
+	}
+
+	dev_dbg(dev, "cmdq device: addr:0x%p, va:0x%p, irq:%d\n",
+		dev, cmdq->base, cmdq->irq);
+
+	cmdq->clock = devm_clk_get(dev, "gce");
+	if (IS_ERR(cmdq->clock)) {
+		dev_err(dev, "failed to get gce clk\n");
+		return PTR_ERR(cmdq->clock);
+	}
+
+	cmdq->thread_nr = (u32)(unsigned long)of_device_get_match_data(dev);
+	cmdq->mbox.dev = dev;
+	cmdq->mbox.chans = devm_kcalloc(dev, cmdq->thread_nr,
+					sizeof(*cmdq->mbox.chans), GFP_KERNEL);
+	if (!cmdq->mbox.chans)
+		return -ENOMEM;
+
+	cmdq->mbox.num_chans = cmdq->thread_nr;
+	cmdq->mbox.ops = &cmdq_mbox_chan_ops;
+	cmdq->mbox.of_xlate = cmdq_xlate;
+
+	/* make use of TXDONE_BY_ACK */
+	cmdq->mbox.txdone_irq = false;
+	cmdq->mbox.txdone_poll = false;
+
+	cmdq->thread = devm_kcalloc(dev, cmdq->thread_nr,
+					sizeof(*cmdq->thread), GFP_KERNEL);
+	if (!cmdq->thread)
+		return -ENOMEM;
+
+	for (i = 0; i < cmdq->thread_nr; i++) {
+		cmdq->thread[i].base = cmdq->base + CMDQ_THR_BASE +
+				CMDQ_THR_SIZE * i;
+		INIT_LIST_HEAD(&cmdq->thread[i].task_busy_list);
+		cmdq->mbox.chans[i].con_priv = (void *)&cmdq->thread[i];
+	}
+
+	err = mbox_controller_register(&cmdq->mbox);
+	if (err < 0) {
+		dev_err(dev, "failed to register mailbox: %d\n", err);
+		return err;
+	}
+
+	platform_set_drvdata(pdev, cmdq);
+	WARN_ON(clk_prepare(cmdq->clock) < 0);
+
+	cmdq_init(cmdq);
+
+	return 0;
+}
+
+static const struct dev_pm_ops cmdq_pm_ops = {
+	.suspend = cmdq_suspend,
+	.resume = cmdq_resume,
+};
+
+static const struct of_device_id cmdq_of_ids[] = {
+	{.compatible = "mediatek,mt8173-gce", .data = (void *)16},
+	{}
+};
+
+static struct platform_driver cmdq_drv = {
+	.probe = cmdq_probe,
+	.remove = cmdq_remove,
+	.driver = {
+		.name = "mtk_cmdq",
+		.pm = &cmdq_pm_ops,
+		.of_match_table = cmdq_of_ids,
+	}
+};
+
+static int __init cmdq_drv_init(void)
+{
+	return platform_driver_register(&cmdq_drv);
+}
+
+static void __exit cmdq_drv_exit(void)
+{
+	platform_driver_unregister(&cmdq_drv);
+}
+
+subsys_initcall(cmdq_drv_init);
+module_exit(cmdq_drv_exit);
+
+MODULE_LICENSE("GPL v2");

drivers/mailbox/omap-mailbox.c

@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0
 /*
  * OMAP mailbox driver
  *
@@ -6,15 +7,6 @@
  *
  * Contact: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
  *          Suman Anna <s-anna@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
  */
 
 #include <linux/interrupt.h>
@@ -77,6 +69,10 @@ struct omap_mbox_queue {
 	bool full;
 };
 
+struct omap_mbox_match_data {
+	u32 intr_type;
+};
+
 struct omap_mbox_device {
 	struct device *dev;
 	struct mutex cfg_lock;
@@ -646,18 +642,21 @@ static const struct dev_pm_ops omap_mbox_pm_ops = {
 	SET_SYSTEM_SLEEP_PM_OPS(omap_mbox_suspend, omap_mbox_resume)
 };
 
+static const struct omap_mbox_match_data omap2_data = { MBOX_INTR_CFG_TYPE1 };
+static const struct omap_mbox_match_data omap4_data = { MBOX_INTR_CFG_TYPE2 };
+
 static const struct of_device_id omap_mailbox_of_match[] = {
 	{
 		.compatible	= "ti,omap2-mailbox",
-		.data		= (void *)MBOX_INTR_CFG_TYPE1,
+		.data		= &omap2_data,
 	},
 	{
 		.compatible	= "ti,omap3-mailbox",
-		.data		= (void *)MBOX_INTR_CFG_TYPE1,
+		.data		= &omap2_data,
 	},
 	{
 		.compatible	= "ti,omap4-mailbox",
-		.data		= (void *)MBOX_INTR_CFG_TYPE2,
+		.data		= &omap4_data,
 	},
 	{
 		/* end */
@@ -700,7 +699,7 @@ static int omap_mbox_probe(struct platform_device *pdev)
 	struct omap_mbox_fifo *fifo;
 	struct device_node *node = pdev->dev.of_node;
 	struct device_node *child;
-	const struct of_device_id *match;
+	const struct omap_mbox_match_data *match_data;
 	u32 intr_type, info_count;
 	u32 num_users, num_fifos;
 	u32 tmp[3];
@@ -712,10 +711,10 @@ static int omap_mbox_probe(struct platform_device *pdev)
 		return -ENODEV;
 	}
 
-	match = of_match_device(omap_mailbox_of_match, &pdev->dev);
-	if (!match)
+	match_data = of_device_get_match_data(&pdev->dev);
+	if (!match_data)
 		return -ENODEV;
-	intr_type = (u32)match->data;
+	intr_type = match_data->intr_type;
 
 	if (of_property_read_u32(node, "ti,mbox-num-users", &num_users))
 		return -ENODEV;

drivers/mailbox/ti-msgmgr.c

@@ -25,6 +25,17 @@
 #define Q_STATE_OFFSET(queue)			((queue) * 0x4)
 #define Q_STATE_ENTRY_COUNT_MASK		(0xFFF000)
 
+#define SPROXY_THREAD_OFFSET(tid) (0x1000 * (tid))
+#define SPROXY_THREAD_DATA_OFFSET(tid, reg) \
+	(SPROXY_THREAD_OFFSET(tid) + ((reg) * 0x4) + 0x4)
+
+#define SPROXY_THREAD_STATUS_OFFSET(tid) (SPROXY_THREAD_OFFSET(tid))
+
+#define SPROXY_THREAD_STATUS_COUNT_MASK (0xFF)
+
+#define SPROXY_THREAD_CTRL_OFFSET(tid) (0x1000 + SPROXY_THREAD_OFFSET(tid))
+#define SPROXY_THREAD_CTRL_DIR_MASK (0x1 << 31)
+
 /**
  * struct ti_msgmgr_valid_queue_desc - SoC valid queues meant for this processor
  * @queue_id:	Queue Number for this path
@@ -42,14 +53,18 @@ struct ti_msgmgr_valid_queue_desc {
  * @queue_count:	Number of Queues
  * @max_message_size:	Message size in bytes
  * @max_messages:	Number of messages
- * @q_slices:		Number of queue engines
- * @q_proxies:		Number of queue proxies per page
  * @data_first_reg:	First data register for proxy data region
  * @data_last_reg:	Last data register for proxy data region
+ * @status_cnt_mask:	Mask for getting the status value
+ * @status_err_mask:	Mask for getting the error value, if applicable
  * @tx_polled:		Do I need to use polled mechanism for tx
  * @tx_poll_timeout_ms: Timeout in ms if polled
  * @valid_queues:	List of Valid queues that the processor can access
+ * @data_region_name:	Name of the proxy data region
+ * @status_region_name:	Name of the proxy status region
+ * @ctrl_region_name:	Name of the proxy control region
  * @num_valid_queues:	Number of valid queues
+ * @is_sproxy:		Is this an Secure Proxy instance?
  *
  * This structure is used in of match data to describe how integration
  * for a specific compatible SoC is done.
@@ -58,14 +73,18 @@ struct ti_msgmgr_desc {
 	u8 queue_count;
 	u8 max_message_size;
 	u8 max_messages;
-	u8 q_slices;
-	u8 q_proxies;
 	u8 data_first_reg;
 	u8 data_last_reg;
+	u32 status_cnt_mask;
+	u32 status_err_mask;
 	bool tx_polled;
 	int tx_poll_timeout_ms;
 	const struct ti_msgmgr_valid_queue_desc *valid_queues;
+	const char *data_region_name;
+	const char *status_region_name;
+	const char *ctrl_region_name;
 	int num_valid_queues;
+	bool is_sproxy;
 };
 
 /**
@@ -78,6 +97,7 @@ struct ti_msgmgr_desc {
  * @queue_buff_start: First register of Data Buffer
  * @queue_buff_end: Last (or confirmation) register of Data buffer
  * @queue_state: Queue status register
+ * @queue_ctrl: Queue Control register
  * @chan:	Mailbox channel
  * @rx_buff:	Receive buffer pointer allocated at probe, max_message_size
  */
@@ -90,6 +110,7 @@ struct ti_queue_inst {
 	void __iomem *queue_buff_start;
 	void __iomem *queue_buff_end;
 	void __iomem *queue_state;
+	void __iomem *queue_ctrl;
 	struct mbox_chan *chan;
 	u32 *rx_buff;
 };
@@ -100,6 +121,7 @@ struct ti_queue_inst {
  * @desc:	Description of the SoC integration
  * @queue_proxy_region:	Queue proxy region where queue buffers are located
  * @queue_state_debug_region:	Queue status register regions
+ * @queue_ctrl_region:	Queue Control register regions
  * @num_valid_queues:	Number of valid queues defined for the processor
  *		Note: other queues are probably reserved for other processors
  *		in the SoC.
@@ -112,6 +134,7 @@ struct ti_msgmgr_inst {
 	const struct ti_msgmgr_desc *desc;
 	void __iomem *queue_proxy_region;
 	void __iomem *queue_state_debug_region;
+	void __iomem *queue_ctrl_region;
 	u8 num_valid_queues;
 	struct ti_queue_inst *qinsts;
 	struct mbox_controller mbox;
@@ -120,24 +143,53 @@ struct ti_msgmgr_inst {
 
 /**
  * ti_msgmgr_queue_get_num_messages() - Get the number of pending messages
+ * @d:		Description of message manager
  * @qinst:	Queue instance for which we check the number of pending messages
  *
  * Return: number of messages pending in the queue (0 == no pending messages)
  */
-static inline int ti_msgmgr_queue_get_num_messages(struct ti_queue_inst *qinst)
+static inline int
+ti_msgmgr_queue_get_num_messages(const struct ti_msgmgr_desc *d,
+				 struct ti_queue_inst *qinst)
 {
 	u32 val;
+	u32 status_cnt_mask = d->status_cnt_mask;
 
 	/*
 	 * We cannot use relaxed operation here - update may happen
 	 * real-time.
 	 */
-	val = readl(qinst->queue_state) & Q_STATE_ENTRY_COUNT_MASK;
-	val >>= __ffs(Q_STATE_ENTRY_COUNT_MASK);
+	val = readl(qinst->queue_state) & status_cnt_mask;
+	val >>= __ffs(status_cnt_mask);
 
 	return val;
 }
 
+/**
+ * ti_msgmgr_queue_is_error() - Check to see if there is queue error
+ * @d:		Description of message manager
+ * @qinst:	Queue instance for which we check the number of pending messages
+ *
+ * Return: true if error, else false
+ */
+static inline bool ti_msgmgr_queue_is_error(const struct ti_msgmgr_desc *d,
+					    struct ti_queue_inst *qinst)
+{
+	u32 val;
+
+	/* Msgmgr has no error detection */
+	if (!d->is_sproxy)
+		return false;
+
+	/*
+	 * We cannot use relaxed operation here - update may happen
+	 * real-time.
+	 */
+	val = readl(qinst->queue_state) & d->status_err_mask;
+
+	return val ? true : false;
+}
+
 /**
  * ti_msgmgr_queue_rx_interrupt() - Interrupt handler for receive Queue
  * @irq:	Interrupt number
@@ -171,8 +223,14 @@ static irqreturn_t ti_msgmgr_queue_rx_interrupt(int irq, void *p)
 		return IRQ_NONE;
 	}
 
+	desc = inst->desc;
+	if (ti_msgmgr_queue_is_error(desc, qinst)) {
+		dev_err(dev, "Error on Rx channel %s\n", qinst->name);
+		return IRQ_NONE;
+	}
+
 	/* Do I actually have messages to read? */
-	msg_count = ti_msgmgr_queue_get_num_messages(qinst);
+	msg_count = ti_msgmgr_queue_get_num_messages(desc, qinst);
 	if (!msg_count) {
 		/* Shared IRQ? */
 		dev_dbg(dev, "Spurious event - 0 pending data!\n");
@@ -185,7 +243,6 @@ static irqreturn_t ti_msgmgr_queue_rx_interrupt(int irq, void *p)
 	 * of how many bytes I should be reading. Let the client figure this
 	 * out.. I just read the full message and pass it on..
 	 */
-	desc = inst->desc;
 	message.len = desc->max_message_size;
 	message.buf = (u8 *)qinst->rx_buff;
 
@@ -228,12 +285,20 @@ static irqreturn_t ti_msgmgr_queue_rx_interrupt(int irq, void *p)
 static bool ti_msgmgr_queue_peek_data(struct mbox_chan *chan)
 {
 	struct ti_queue_inst *qinst = chan->con_priv;
+	struct device *dev = chan->mbox->dev;
+	struct ti_msgmgr_inst *inst = dev_get_drvdata(dev);
+	const struct ti_msgmgr_desc *desc = inst->desc;
 	int msg_count;
 
 	if (qinst->is_tx)
 		return false;
 
-	msg_count = ti_msgmgr_queue_get_num_messages(qinst);
+	if (ti_msgmgr_queue_is_error(desc, qinst)) {
+		dev_err(dev, "Error on channel %s\n", qinst->name);
+		return false;
+	}
+
+	msg_count = ti_msgmgr_queue_get_num_messages(desc, qinst);
 
 	return msg_count ? true : false;
 }
@@ -247,12 +312,25 @@ static bool ti_msgmgr_queue_peek_data(struct mbox_chan *chan)
 static bool ti_msgmgr_last_tx_done(struct mbox_chan *chan)
 {
 	struct ti_queue_inst *qinst = chan->con_priv;
+	struct device *dev = chan->mbox->dev;
+	struct ti_msgmgr_inst *inst = dev_get_drvdata(dev);
+	const struct ti_msgmgr_desc *desc = inst->desc;
 	int msg_count;
 
 	if (!qinst->is_tx)
 		return false;
 
-	msg_count = ti_msgmgr_queue_get_num_messages(qinst);
+	if (ti_msgmgr_queue_is_error(desc, qinst)) {
+		dev_err(dev, "Error on channel %s\n", qinst->name);
+		return false;
+	}
+
+	msg_count = ti_msgmgr_queue_get_num_messages(desc, qinst);
+
+	if (desc->is_sproxy) {
+		/* In secure proxy, msg_count indicates how many we can send */
+		return msg_count ? true : false;
+	}
 
 	/* if we have any messages pending.. */
 	return msg_count ? false : true;
@@ -282,6 +360,11 @@ static int ti_msgmgr_send_data(struct mbox_chan *chan, void *data)
 	}
 	desc = inst->desc;
 
+	if (ti_msgmgr_queue_is_error(desc, qinst)) {
+		dev_err(dev, "Error on channel %s\n", qinst->name);
+		return false;
+	}
+
 	if (desc->max_message_size < message->len) {
 		dev_err(dev, "Queue %s message length %zu > max %d\n",
 			qinst->name, message->len, desc->max_message_size);
@@ -314,6 +397,53 @@ static int ti_msgmgr_send_data(struct mbox_chan *chan, void *data)
 	return 0;
 }
 
+/**
+ *  ti_msgmgr_queue_rx_irq_req() - RX IRQ request
+ *  @dev:	device pointer
+ *  @d:		descriptor for ti_msgmgr
+ *  @qinst:	Queue instance
+ *  @chan:	Channel pointer
+ */
+static int ti_msgmgr_queue_rx_irq_req(struct device *dev,
+				      const struct ti_msgmgr_desc *d,
+				      struct ti_queue_inst *qinst,
+				      struct mbox_chan *chan)
+{
+	int ret = 0;
+	char of_rx_irq_name[7];
+	struct device_node *np;
+
+	snprintf(of_rx_irq_name, sizeof(of_rx_irq_name),
+		 "rx_%03d", d->is_sproxy ? qinst->proxy_id : qinst->queue_id);
+
+	/* Get the IRQ if not found */
+	if (qinst->irq < 0) {
+		np = of_node_get(dev->of_node);
+		if (!np)
+			return -ENODATA;
+		qinst->irq = of_irq_get_byname(np, of_rx_irq_name);
+		of_node_put(np);
+
+		if (qinst->irq < 0) {
+			dev_err(dev,
+				"QID %d PID %d:No IRQ[%s]: %d\n",
+				qinst->queue_id, qinst->proxy_id,
+				of_rx_irq_name, qinst->irq);
+			return qinst->irq;
+		}
+	}
+
+	/* With the expectation that the IRQ might be shared in SoC */
+	ret = request_irq(qinst->irq, ti_msgmgr_queue_rx_interrupt,
+			  IRQF_SHARED, qinst->name, chan);
+	if (ret) {
+		dev_err(dev, "Unable to get IRQ %d on %s(res=%d)\n",
+			qinst->irq, qinst->name, ret);
+	}
+
+	return ret;
+}
+
 /**
  * ti_msgmgr_queue_startup() - Startup queue
  * @chan:	Channel pointer
@@ -322,19 +452,39 @@ static int ti_msgmgr_send_data(struct mbox_chan *chan, void *data)
  */
 static int ti_msgmgr_queue_startup(struct mbox_chan *chan)
 {
-	struct ti_queue_inst *qinst = chan->con_priv;
 	struct device *dev = chan->mbox->dev;
+	struct ti_msgmgr_inst *inst = dev_get_drvdata(dev);
+	struct ti_queue_inst *qinst = chan->con_priv;
+	const struct ti_msgmgr_desc *d = inst->desc;
 	int ret;
+	int msg_count;
+
+	/*
+	 * If sproxy is starting and can send messages, we are a Tx thread,
+	 * else Rx
+	 */
+	if (d->is_sproxy) {
+		qinst->is_tx = (readl(qinst->queue_ctrl) &
+				SPROXY_THREAD_CTRL_DIR_MASK) ? false : true;
+
+		msg_count = ti_msgmgr_queue_get_num_messages(d, qinst);
+
+		if (!msg_count && qinst->is_tx) {
+			dev_err(dev, "%s: Cannot transmit with 0 credits!\n",
+				qinst->name);
+			return -EINVAL;
+		}
+	}
 
 	if (!qinst->is_tx) {
-		/*
-		 * With the expectation that the IRQ might be shared in SoC
-		 */
-		ret = request_irq(qinst->irq, ti_msgmgr_queue_rx_interrupt,
-				  IRQF_SHARED, qinst->name, chan);
+		/* Allocate usage buffer for rx */
+		qinst->rx_buff = kzalloc(d->max_message_size, GFP_KERNEL);
+		if (!qinst->rx_buff)
+			return -ENOMEM;
+		/* Request IRQ */
+		ret = ti_msgmgr_queue_rx_irq_req(dev, d, qinst, chan);
 		if (ret) {
-			dev_err(dev, "Unable to get IRQ %d on %s(res=%d)\n",
-				qinst->irq, qinst->name, ret);
+			kfree(qinst->rx_buff);
 			return ret;
 		}
 	}
@@ -350,8 +500,10 @@ static void ti_msgmgr_queue_shutdown(struct mbox_chan *chan)
 {
 	struct ti_queue_inst *qinst = chan->con_priv;
 
-	if (!qinst->is_tx)
+	if (!qinst->is_tx) {
 		free_irq(qinst->irq, chan);
+		kfree(qinst->rx_buff);
+	}
 }
 
 /**
@@ -368,20 +520,38 @@ static struct mbox_chan *ti_msgmgr_of_xlate(struct mbox_controller *mbox,
 	struct ti_msgmgr_inst *inst;
 	int req_qid, req_pid;
 	struct ti_queue_inst *qinst;
-	int i;
+	const struct ti_msgmgr_desc *d;
+	int i, ncells;
 
 	inst = container_of(mbox, struct ti_msgmgr_inst, mbox);
 	if (WARN_ON(!inst))
 		return ERR_PTR(-EINVAL);
 
-	/* #mbox-cells is 2 */
-	if (p->args_count != 2) {
-		dev_err(inst->dev, "Invalid arguments in dt[%d] instead of 2\n",
-			p->args_count);
+	d = inst->desc;
+
+	if (d->is_sproxy)
+		ncells = 1;
+	else
+		ncells = 2;
+	if (p->args_count != ncells) {
+		dev_err(inst->dev, "Invalid arguments in dt[%d]. Must be %d\n",
+			p->args_count, ncells);
 		return ERR_PTR(-EINVAL);
 	}
-	req_qid = p->args[0];
-	req_pid = p->args[1];
+	if (ncells == 1) {
+		req_qid = 0;
+		req_pid = p->args[0];
+	} else {
+		req_qid = p->args[0];
+		req_pid = p->args[1];
+	}
+
+	if (d->is_sproxy) {
+		if (req_pid > d->num_valid_queues)
+			goto err;
+		qinst = &inst->qinsts[req_pid];
+		return qinst->chan;
+	}
 
 	for (qinst = inst->qinsts, i = 0; i < inst->num_valid_queues;
 	     i++, qinst++) {
@@ -389,6 +559,7 @@ static struct mbox_chan *ti_msgmgr_of_xlate(struct mbox_controller *mbox,
 			return qinst->chan;
 	}
 
+err:
 	dev_err(inst->dev, "Queue ID %d, Proxy ID %d is wrong on %s\n",
 		req_qid, req_pid, p->np->name);
 	return ERR_PTR(-ENOENT);
@@ -415,6 +586,8 @@ static int ti_msgmgr_queue_setup(int idx, struct device *dev,
 				 struct ti_queue_inst *qinst,
 				 struct mbox_chan *chan)
 {
+	char *dir;
+
 	qinst->proxy_id = qd->proxy_id;
 	qinst->queue_id = qd->queue_id;
 
@@ -424,40 +597,43 @@ static int ti_msgmgr_queue_setup(int idx, struct device *dev,
 		return -ERANGE;
 	}
 
-	qinst->is_tx = qd->is_tx;
-	snprintf(qinst->name, sizeof(qinst->name), "%s %s_%03d_%03d",
-		 dev_name(dev), qinst->is_tx ? "tx" : "rx", qinst->queue_id,
-		 qinst->proxy_id);
-
-	if (!qinst->is_tx) {
-		char of_rx_irq_name[7];
-
-		snprintf(of_rx_irq_name, sizeof(of_rx_irq_name),
-			 "rx_%03d", qinst->queue_id);
-
-		qinst->irq = of_irq_get_byname(np, of_rx_irq_name);
-		if (qinst->irq < 0) {
-			dev_crit(dev,
-				 "[%d]QID %d PID %d:No IRQ[%s]: %d\n",
-				 idx, qinst->queue_id, qinst->proxy_id,
-				 of_rx_irq_name, qinst->irq);
-			return qinst->irq;
-		}
-		/* Allocate usage buffer for rx */
-		qinst->rx_buff = devm_kzalloc(dev,
-					      d->max_message_size, GFP_KERNEL);
-		if (!qinst->rx_buff)
-			return -ENOMEM;
+	if (d->is_sproxy) {
+		qinst->queue_buff_start = inst->queue_proxy_region +
+		    SPROXY_THREAD_DATA_OFFSET(qinst->proxy_id,
+					      d->data_first_reg);
+		qinst->queue_buff_end = inst->queue_proxy_region +
+		    SPROXY_THREAD_DATA_OFFSET(qinst->proxy_id,
+					      d->data_last_reg);
+		qinst->queue_state = inst->queue_state_debug_region +
+		    SPROXY_THREAD_STATUS_OFFSET(qinst->proxy_id);
+		qinst->queue_ctrl = inst->queue_ctrl_region +
+		    SPROXY_THREAD_CTRL_OFFSET(qinst->proxy_id);
+
+		/* XXX: DONOT read registers here!.. Some may be unusable */
+		dir = "thr";
+		snprintf(qinst->name, sizeof(qinst->name), "%s %s_%03d",
+			 dev_name(dev), dir, qinst->proxy_id);
+	} else {
+		qinst->queue_buff_start = inst->queue_proxy_region +
+		    Q_DATA_OFFSET(qinst->proxy_id, qinst->queue_id,
+				  d->data_first_reg);
+		qinst->queue_buff_end = inst->queue_proxy_region +
+		    Q_DATA_OFFSET(qinst->proxy_id, qinst->queue_id,
+				  d->data_last_reg);
+		qinst->queue_state =
+		    inst->queue_state_debug_region +
+		    Q_STATE_OFFSET(qinst->queue_id);
+		qinst->is_tx = qd->is_tx;
+		dir = qinst->is_tx ? "tx" : "rx";
+		snprintf(qinst->name, sizeof(qinst->name), "%s %s_%03d_%03d",
+			 dev_name(dev), dir, qinst->queue_id, qinst->proxy_id);
 	}
 
-	qinst->queue_buff_start = inst->queue_proxy_region +
-	    Q_DATA_OFFSET(qinst->proxy_id, qinst->queue_id, d->data_first_reg);
-	qinst->queue_buff_end = inst->queue_proxy_region +
-	    Q_DATA_OFFSET(qinst->proxy_id, qinst->queue_id, d->data_last_reg);
-	qinst->queue_state = inst->queue_state_debug_region +
-	    Q_STATE_OFFSET(qinst->queue_id);
 	qinst->chan = chan;
 
+	/* Setup an error value for IRQ - Lazy allocation */
+	qinst->irq = -EINVAL;
+
 	chan->con_priv = qinst;
 
 	dev_dbg(dev, "[%d] qidx=%d pidx=%d irq=%d q_s=%p q_e = %p\n",
@@ -494,19 +670,37 @@ static const struct ti_msgmgr_desc k2g_desc = {
 	.queue_count = 64,
 	.max_message_size = 64,
 	.max_messages = 128,
-	.q_slices = 1,
-	.q_proxies = 1,
+	.data_region_name = "queue_proxy_region",
+	.status_region_name = "queue_state_debug_region",
 	.data_first_reg = 16,
 	.data_last_reg = 31,
+	.status_cnt_mask = Q_STATE_ENTRY_COUNT_MASK,
 	.tx_polled = false,
 	.valid_queues = k2g_valid_queues,
 	.num_valid_queues = ARRAY_SIZE(k2g_valid_queues),
+	.is_sproxy = false,
+};
+
+static const struct ti_msgmgr_desc am654_desc = {
+	.queue_count = 190,
+	.num_valid_queues = 190,
+	.max_message_size = 60,
+	.data_region_name = "target_data",
+	.status_region_name = "rt",
+	.ctrl_region_name = "scfg",
+	.data_first_reg = 0,
+	.data_last_reg = 14,
+	.status_cnt_mask = SPROXY_THREAD_STATUS_COUNT_MASK,
+	.tx_polled = false,
+	.is_sproxy = true,
 };
 
 static const struct of_device_id ti_msgmgr_of_match[] = {
 	{.compatible = "ti,k2g-message-manager", .data = &k2g_desc},
+	{.compatible = "ti,am654-secure-proxy", .data = &am654_desc},
 	{ /* Sentinel */ }
 };
+
 MODULE_DEVICE_TABLE(of, ti_msgmgr_of_match);
 
 static int ti_msgmgr_probe(struct platform_device *pdev)
@@ -546,17 +740,25 @@ static int ti_msgmgr_probe(struct platform_device *pdev)
 	inst->desc = desc;
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-					   "queue_proxy_region");
+					   desc->data_region_name);
 	inst->queue_proxy_region = devm_ioremap_resource(dev, res);
 	if (IS_ERR(inst->queue_proxy_region))
 		return PTR_ERR(inst->queue_proxy_region);
 
 	res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-					   "queue_state_debug_region");
+					   desc->status_region_name);
 	inst->queue_state_debug_region = devm_ioremap_resource(dev, res);
 	if (IS_ERR(inst->queue_state_debug_region))
 		return PTR_ERR(inst->queue_state_debug_region);
 
+	if (desc->is_sproxy) {
+		res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
+						   desc->ctrl_region_name);
+		inst->queue_ctrl_region = devm_ioremap_resource(dev, res);
+		if (IS_ERR(inst->queue_ctrl_region))
+			return PTR_ERR(inst->queue_ctrl_region);
+	}
+
 	dev_dbg(dev, "proxy region=%p, queue_state=%p\n",
 		inst->queue_proxy_region, inst->queue_state_debug_region);
 
@@ -578,12 +780,29 @@ static int ti_msgmgr_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	inst->chans = chans;
 
-	for (i = 0, queue_desc = desc->valid_queues;
-	     i < queue_count; i++, qinst++, chans++, queue_desc++) {
-		ret = ti_msgmgr_queue_setup(i, dev, np, inst,
-					    desc, queue_desc, qinst, chans);
-		if (ret)
-			return ret;
+	if (desc->is_sproxy) {
+		struct ti_msgmgr_valid_queue_desc sproxy_desc;
+
+		/* All proxies may be valid in Secure Proxy instance */
+		for (i = 0; i < queue_count; i++, qinst++, chans++) {
+			sproxy_desc.queue_id = 0;
+			sproxy_desc.proxy_id = i;
+			ret = ti_msgmgr_queue_setup(i, dev, np, inst,
+						    desc, &sproxy_desc, qinst,
+						    chans);
+			if (ret)
+				return ret;
+		}
+	} else {
+		/* Only Some proxies are valid in Message Manager */
+		for (i = 0, queue_desc = desc->valid_queues;
+		     i < queue_count; i++, qinst++, chans++, queue_desc++) {
+			ret = ti_msgmgr_queue_setup(i, dev, np, inst,
+						    desc, queue_desc, qinst,
+						    chans);
+			if (ret)
+				return ret;
+		}
 	}
 
 	mbox = &inst->mbox;

include/dt-bindings/gce/mt8173-gce.h

@@ -0,0 +1,44 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2018 MediaTek Inc.
+ * Author: Houlong Wei <houlong.wei@mediatek.com>
+ *
+ */
+
+#ifndef _DT_BINDINGS_GCE_MT8173_H
+#define _DT_BINDINGS_GCE_MT8173_H
+
+/* GCE HW thread priority */
+#define CMDQ_THR_PRIO_LOWEST	0
+#define CMDQ_THR_PRIO_HIGHEST	1
+
+/* GCE SUBSYS */
+#define SUBSYS_1400XXXX		1
+#define SUBSYS_1401XXXX		2
+#define SUBSYS_1402XXXX		3
+
+/* GCE HW EVENT */
+#define CMDQ_EVENT_DISP_OVL0_SOF		11
+#define CMDQ_EVENT_DISP_OVL1_SOF		12
+#define CMDQ_EVENT_DISP_RDMA0_SOF		13
+#define CMDQ_EVENT_DISP_RDMA1_SOF		14
+#define CMDQ_EVENT_DISP_RDMA2_SOF		15
+#define CMDQ_EVENT_DISP_WDMA0_SOF		16
+#define CMDQ_EVENT_DISP_WDMA1_SOF		17
+#define CMDQ_EVENT_DISP_OVL0_EOF		39
+#define CMDQ_EVENT_DISP_OVL1_EOF		40
+#define CMDQ_EVENT_DISP_RDMA0_EOF		41
+#define CMDQ_EVENT_DISP_RDMA1_EOF		42
+#define CMDQ_EVENT_DISP_RDMA2_EOF		43
+#define CMDQ_EVENT_DISP_WDMA0_EOF		44
+#define CMDQ_EVENT_DISP_WDMA1_EOF		45
+#define CMDQ_EVENT_MUTEX0_STREAM_EOF		53
+#define CMDQ_EVENT_MUTEX1_STREAM_EOF		54
+#define CMDQ_EVENT_MUTEX2_STREAM_EOF		55
+#define CMDQ_EVENT_MUTEX3_STREAM_EOF		56
+#define CMDQ_EVENT_MUTEX4_STREAM_EOF		57
+#define CMDQ_EVENT_DISP_RDMA0_UNDERRUN		63
+#define CMDQ_EVENT_DISP_RDMA1_UNDERRUN		64
+#define CMDQ_EVENT_DISP_RDMA2_UNDERRUN		65
+
+#endif

include/linux/mailbox/mtk-cmdq-mailbox.h

@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2018 MediaTek Inc.
+ *
+ */
+
+#ifndef __MTK_CMDQ_MAILBOX_H__
+#define __MTK_CMDQ_MAILBOX_H__
+
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/types.h>
+
+#define CMDQ_INST_SIZE			8 /* instruction is 64-bit */
+#define CMDQ_SUBSYS_SHIFT		16
+#define CMDQ_OP_CODE_SHIFT		24
+#define CMDQ_JUMP_PASS			CMDQ_INST_SIZE
+
+#define CMDQ_WFE_UPDATE			BIT(31)
+#define CMDQ_WFE_WAIT			BIT(15)
+#define CMDQ_WFE_WAIT_VALUE		0x1
+
+/*
+ * CMDQ_CODE_MASK:
+ *   set write mask
+ *   format: op mask
+ * CMDQ_CODE_WRITE:
+ *   write value into target register
+ *   format: op subsys address value
+ * CMDQ_CODE_JUMP:
+ *   jump by offset
+ *   format: op offset
+ * CMDQ_CODE_WFE:
+ *   wait for event and clear
+ *   it is just clear if no wait
+ *   format: [wait]  op event update:1 to_wait:1 wait:1
+ *           [clear] op event update:1 to_wait:0 wait:0
+ * CMDQ_CODE_EOC:
+ *   end of command
+ *   format: op irq_flag
+ */
+enum cmdq_code {
+	CMDQ_CODE_MASK = 0x02,
+	CMDQ_CODE_WRITE = 0x04,
+	CMDQ_CODE_JUMP = 0x10,
+	CMDQ_CODE_WFE = 0x20,
+	CMDQ_CODE_EOC = 0x40,
+};
+
+enum cmdq_cb_status {
+	CMDQ_CB_NORMAL = 0,
+	CMDQ_CB_ERROR
+};
+
+struct cmdq_cb_data {
+	enum cmdq_cb_status	sta;
+	void			*data;
+};
+
+typedef void (*cmdq_async_flush_cb)(struct cmdq_cb_data data);
+
+struct cmdq_task_cb {
+	cmdq_async_flush_cb	cb;
+	void			*data;
+};
+
+struct cmdq_pkt {
+	void			*va_base;
+	dma_addr_t		pa_base;
+	size_t			cmd_buf_size; /* command occupied size */
+	size_t			buf_size; /* real buffer size */
+	struct cmdq_task_cb	cb;
+	struct cmdq_task_cb	async_cb;
+	void			*cl;
+};
+
+#endif /* __MTK_CMDQ_MAILBOX_H__ */

include/linux/omap-mailbox.h

@@ -1,9 +1,6 @@
+/* SPDX-License-Identifier: GPL-2.0 */
 /*
  * omap-mailbox: interprocessor communication module for OMAP
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 #ifndef OMAP_MAILBOX_H