Merge tag 'ib-mfd-pwm-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into for-next

Immutable branch between MFD and PWM due for the v4.18 merge window (v2)

Documentation/devicetree/bindings/mfd/stm32-timers.txt

@@ -19,6 +19,11 @@ Required parameters:
 Optional parameters:
 - resets:		Phandle to the parent reset controller.
 			See ../reset/st,stm32-rcc.txt
+- dmas:			List of phandle to dma channels that can be used for
+			this timer instance. There may be up to 7 dma channels.
+- dma-names:		List of dma names. Must match 'dmas' property. Valid
+			names are: "ch1", "ch2", "ch3", "ch4", "up", "trig",
+			"com".
 
 Optional subnodes:
 - pwm:			See ../pwm/pwm-stm32.txt
@@ -44,3 +49,18 @@ Example:
 			reg = <0>;
 		};
 	};
+
+Example with all dmas:
+	timer@40010000 {
+		...
+		dmas = <&dmamux1 11 0x400 0x0>,
+		       <&dmamux1 12 0x400 0x0>,
+		       <&dmamux1 13 0x400 0x0>,
+		       <&dmamux1 14 0x400 0x0>,
+		       <&dmamux1 15 0x400 0x0>,
+		       <&dmamux1 16 0x400 0x0>,
+		       <&dmamux1 17 0x400 0x0>;
+		dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig", "com";
+		...
+		child nodes...
+	};

drivers/mfd/stm32-timers.c

@@ -4,16 +4,156 @@
  * Author: Benjamin Gaignard <benjamin.gaignard@st.com>
  */
 
+#include <linux/bitfield.h>
 #include <linux/mfd/stm32-timers.h>
 #include <linux/module.h>
 #include <linux/of_platform.h>
 #include <linux/reset.h>
 
+#define STM32_TIMERS_MAX_REGISTERS	0x3fc
+
+/* DIER register DMA enable bits */
+static const u32 stm32_timers_dier_dmaen[STM32_TIMERS_MAX_DMAS] = {
+	TIM_DIER_CC1DE,
+	TIM_DIER_CC2DE,
+	TIM_DIER_CC3DE,
+	TIM_DIER_CC4DE,
+	TIM_DIER_UIE,
+	TIM_DIER_TDE,
+	TIM_DIER_COMDE
+};
+
+static void stm32_timers_dma_done(void *p)
+{
+	struct stm32_timers_dma *dma = p;
+	struct dma_tx_state state;
+	enum dma_status status;
+
+	status = dmaengine_tx_status(dma->chan, dma->chan->cookie, &state);
+	if (status == DMA_COMPLETE)
+		complete(&dma->completion);
+}
+
+/**
+ * stm32_timers_dma_burst_read - Read from timers registers using DMA.
+ *
+ * Read from STM32 timers registers using DMA on a single event.
+ * @dev: reference to stm32_timers MFD device
+ * @buf: DMA'able destination buffer
+ * @id: stm32_timers_dmas event identifier (ch[1..4], up, trig or com)
+ * @reg: registers start offset for DMA to read from (like CCRx for capture)
+ * @num_reg: number of registers to read upon each DMA request, starting @reg.
+ * @bursts: number of bursts to read (e.g. like two for pwm period capture)
+ * @tmo_ms: timeout (milliseconds)
+ */
+int stm32_timers_dma_burst_read(struct device *dev, u32 *buf,
+				enum stm32_timers_dmas id, u32 reg,
+				unsigned int num_reg, unsigned int bursts,
+				unsigned long tmo_ms)
+{
+	struct stm32_timers *ddata = dev_get_drvdata(dev);
+	unsigned long timeout = msecs_to_jiffies(tmo_ms);
+	struct regmap *regmap = ddata->regmap;
+	struct stm32_timers_dma *dma = &ddata->dma;
+	size_t len = num_reg * bursts * sizeof(u32);
+	struct dma_async_tx_descriptor *desc;
+	struct dma_slave_config config;
+	dma_cookie_t cookie;
+	dma_addr_t dma_buf;
+	u32 dbl, dba;
+	long err;
+	int ret;
+
+	/* Sanity check */
+	if (id < STM32_TIMERS_DMA_CH1 || id >= STM32_TIMERS_MAX_DMAS)
+		return -EINVAL;
+
+	if (!num_reg || !bursts || reg > STM32_TIMERS_MAX_REGISTERS ||
+	    (reg + num_reg * sizeof(u32)) > STM32_TIMERS_MAX_REGISTERS)
+		return -EINVAL;
+
+	if (!dma->chans[id])
+		return -ENODEV;
+	mutex_lock(&dma->lock);
+
+	/* Select DMA channel in use */
+	dma->chan = dma->chans[id];
+	dma_buf = dma_map_single(dev, buf, len, DMA_FROM_DEVICE);
+	if (dma_mapping_error(dev, dma_buf)) {
+		ret = -ENOMEM;
+		goto unlock;
+	}
+
+	/* Prepare DMA read from timer registers, using DMA burst mode */
+	memset(&config, 0, sizeof(config));
+	config.src_addr = (dma_addr_t)dma->phys_base + TIM_DMAR;
+	config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
+	ret = dmaengine_slave_config(dma->chan, &config);
+	if (ret)
+		goto unmap;
+
+	desc = dmaengine_prep_slave_single(dma->chan, dma_buf, len,
+					   DMA_DEV_TO_MEM, DMA_PREP_INTERRUPT);
+	if (!desc) {
+		ret = -EBUSY;
+		goto unmap;
+	}
+
+	desc->callback = stm32_timers_dma_done;
+	desc->callback_param = dma;
+	cookie = dmaengine_submit(desc);
+	ret = dma_submit_error(cookie);
+	if (ret)
+		goto dma_term;
+
+	reinit_completion(&dma->completion);
+	dma_async_issue_pending(dma->chan);
+
+	/* Setup and enable timer DMA burst mode */
+	dbl = FIELD_PREP(TIM_DCR_DBL, bursts - 1);
+	dba = FIELD_PREP(TIM_DCR_DBA, reg >> 2);
+	ret = regmap_write(regmap, TIM_DCR, dbl | dba);
+	if (ret)
+		goto dma_term;
+
+	/* Clear pending flags before enabling DMA request */
+	ret = regmap_write(regmap, TIM_SR, 0);
+	if (ret)
+		goto dcr_clr;
+
+	ret = regmap_update_bits(regmap, TIM_DIER, stm32_timers_dier_dmaen[id],
+				 stm32_timers_dier_dmaen[id]);
+	if (ret)
+		goto dcr_clr;
+
+	err = wait_for_completion_interruptible_timeout(&dma->completion,
+							timeout);
+	if (err == 0)
+		ret = -ETIMEDOUT;
+	else if (err < 0)
+		ret = err;
+
+	regmap_update_bits(regmap, TIM_DIER, stm32_timers_dier_dmaen[id], 0);
+	regmap_write(regmap, TIM_SR, 0);
+dcr_clr:
+	regmap_write(regmap, TIM_DCR, 0);
+dma_term:
+	dmaengine_terminate_all(dma->chan);
+unmap:
+	dma_unmap_single(dev, dma_buf, len, DMA_FROM_DEVICE);
+unlock:
+	dma->chan = NULL;
+	mutex_unlock(&dma->lock);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(stm32_timers_dma_burst_read);
+
 static const struct regmap_config stm32_timers_regmap_cfg = {
 	.reg_bits = 32,
 	.val_bits = 32,
 	.reg_stride = sizeof(u32),
-	.max_register = 0x3fc,
+	.max_register = STM32_TIMERS_MAX_REGISTERS,
 };
 
 static void stm32_timers_get_arr_size(struct stm32_timers *ddata)
@@ -27,12 +167,45 @@ static void stm32_timers_get_arr_size(struct stm32_timers *ddata)
 	regmap_write(ddata->regmap, TIM_ARR, 0x0);
 }
 
+static void stm32_timers_dma_probe(struct device *dev,
+				   struct stm32_timers *ddata)
+{
+	int i;
+	char name[4];
+
+	init_completion(&ddata->dma.completion);
+	mutex_init(&ddata->dma.lock);
+
+	/* Optional DMA support: get valid DMA channel(s) or NULL */
+	for (i = STM32_TIMERS_DMA_CH1; i <= STM32_TIMERS_DMA_CH4; i++) {
+		snprintf(name, ARRAY_SIZE(name), "ch%1d", i + 1);
+		ddata->dma.chans[i] = dma_request_slave_channel(dev, name);
+	}
+	ddata->dma.chans[STM32_TIMERS_DMA_UP] =
+		dma_request_slave_channel(dev, "up");
+	ddata->dma.chans[STM32_TIMERS_DMA_TRIG] =
+		dma_request_slave_channel(dev, "trig");
+	ddata->dma.chans[STM32_TIMERS_DMA_COM] =
+		dma_request_slave_channel(dev, "com");
+}
+
+static void stm32_timers_dma_remove(struct device *dev,
+				    struct stm32_timers *ddata)
+{
+	int i;
+
+	for (i = STM32_TIMERS_DMA_CH1; i < STM32_TIMERS_MAX_DMAS; i++)
+		if (ddata->dma.chans[i])
+			dma_release_channel(ddata->dma.chans[i]);
+}
+
 static int stm32_timers_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct stm32_timers *ddata;
 	struct resource *res;
 	void __iomem *mmio;
+	int ret;
 
 	ddata = devm_kzalloc(dev, sizeof(*ddata), GFP_KERNEL);
 	if (!ddata)
@@ -43,6 +216,9 @@ static int stm32_timers_probe(struct platform_device *pdev)
 	if (IS_ERR(mmio))
 		return PTR_ERR(mmio);
 
+	/* Timer physical addr for DMA */
+	ddata->dma.phys_base = res->start;
+
 	ddata->regmap = devm_regmap_init_mmio_clk(dev, "int", mmio,
 						  &stm32_timers_regmap_cfg);
 	if (IS_ERR(ddata->regmap))
@@ -54,9 +230,29 @@ static int stm32_timers_probe(struct platform_device *pdev)
 
 	stm32_timers_get_arr_size(ddata);
 
+	stm32_timers_dma_probe(dev, ddata);
+
 	platform_set_drvdata(pdev, ddata);
 
-	return devm_of_platform_populate(&pdev->dev);
+	ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+	if (ret)
+		stm32_timers_dma_remove(dev, ddata);
+
+	return ret;
+}
+
+static int stm32_timers_remove(struct platform_device *pdev)
+{
+	struct stm32_timers *ddata = platform_get_drvdata(pdev);
+
+	/*
+	 * Don't use devm_ here: enfore of_platform_depopulate() happens before
+	 * DMA are released, to avoid race on DMA.
+	 */
+	of_platform_depopulate(&pdev->dev);
+	stm32_timers_dma_remove(&pdev->dev, ddata);
+
+	return 0;
 }
 
 static const struct of_device_id stm32_timers_of_match[] = {
@@ -67,6 +263,7 @@ MODULE_DEVICE_TABLE(of, stm32_timers_of_match);
 
 static struct platform_driver stm32_timers_driver = {
 	.probe = stm32_timers_probe,
+	.remove = stm32_timers_remove,
 	.driver	= {
 		.name = "stm32-timers",
 		.of_match_table = stm32_timers_of_match,

drivers/pwm/pwm-stm32.c

@@ -8,6 +8,7 @@
  *             pwm-atmel.c from Bo Shen
  */
 
+#include <linux/bitfield.h>
 #include <linux/mfd/stm32-timers.h>
 #include <linux/module.h>
 #include <linux/of.h>
@@ -25,6 +26,7 @@ struct stm32_pwm {
 	struct regmap *regmap;
 	u32 max_arr;
 	bool have_complementary_output;
+	u32 capture[4] ____cacheline_aligned; /* DMA'able buffer */
 };
 
 struct stm32_breakinput {
@@ -62,6 +64,258 @@ static int write_ccrx(struct stm32_pwm *dev, int ch, u32 value)
 	return -EINVAL;
 }
 
+#define TIM_CCER_CC12P (TIM_CCER_CC1P | TIM_CCER_CC2P)
+#define TIM_CCER_CC12E (TIM_CCER_CC1E | TIM_CCER_CC2E)
+#define TIM_CCER_CC34P (TIM_CCER_CC3P | TIM_CCER_CC4P)
+#define TIM_CCER_CC34E (TIM_CCER_CC3E | TIM_CCER_CC4E)
+
+/*
+ * Capture using PWM input mode:
+ *                              ___          ___
+ * TI[1, 2, 3 or 4]: ........._|   |________|
+ *                             ^0  ^1       ^2
+ *                              .   .        .
+ *                              .   .        XXXXX
+ *                              .   .   XXXXX     |
+ *                              .  XXXXX     .    |
+ *                            XXXXX .        .    |
+ * COUNTER:        ______XXXXX  .   .        .    |_XXX
+ *                 start^       .   .        .        ^stop
+ *                      .       .   .        .
+ *                      v       v   .        v
+ *                                  v
+ * CCR1/CCR3:       tx..........t0...........t2
+ * CCR2/CCR4:       tx..............t1.........
+ *
+ * DMA burst transfer:          |            |
+ *                              v            v
+ * DMA buffer:                  { t0, tx }   { t2, t1 }
+ * DMA done:                                 ^
+ *
+ * 0: IC1/3 snapchot on rising edge: counter value -> CCR1/CCR3
+ *    + DMA transfer CCR[1/3] & CCR[2/4] values (t0, tx: doesn't care)
+ * 1: IC2/4 snapchot on falling edge: counter value -> CCR2/CCR4
+ * 2: IC1/3 snapchot on rising edge: counter value -> CCR1/CCR3
+ *    + DMA transfer CCR[1/3] & CCR[2/4] values (t2, t1)
+ *
+ * DMA done, compute:
+ * - Period     = t2 - t0
+ * - Duty cycle = t1 - t0
+ */
+static int stm32_pwm_raw_capture(struct stm32_pwm *priv, struct pwm_device *pwm,
+				 unsigned long tmo_ms, u32 *raw_prd,
+				 u32 *raw_dty)
+{
+	struct device *parent = priv->chip.dev->parent;
+	enum stm32_timers_dmas dma_id;
+	u32 ccen, ccr;
+	int ret;
+
+	/* Ensure registers have been updated, enable counter and capture */
+	regmap_update_bits(priv->regmap, TIM_EGR, TIM_EGR_UG, TIM_EGR_UG);
+	regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN, TIM_CR1_CEN);
+
+	/* Use cc1 or cc3 DMA resp for PWM input channels 1 & 2 or 3 & 4 */
+	dma_id = pwm->hwpwm < 2 ? STM32_TIMERS_DMA_CH1 : STM32_TIMERS_DMA_CH3;
+	ccen = pwm->hwpwm < 2 ? TIM_CCER_CC12E : TIM_CCER_CC34E;
+	ccr = pwm->hwpwm < 2 ? TIM_CCR1 : TIM_CCR3;
+	regmap_update_bits(priv->regmap, TIM_CCER, ccen, ccen);
+
+	/*
+	 * Timer DMA burst mode. Request 2 registers, 2 bursts, to get both
+	 * CCR1 & CCR2 (or CCR3 & CCR4) on each capture event.
+	 * We'll get two capture snapchots: { CCR1, CCR2 }, { CCR1, CCR2 }
+	 * or { CCR3, CCR4 }, { CCR3, CCR4 }
+	 */
+	ret = stm32_timers_dma_burst_read(parent, priv->capture, dma_id, ccr, 2,
+					  2, tmo_ms);
+	if (ret)
+		goto stop;
+
+	/* Period: t2 - t0 (take care of counter overflow) */
+	if (priv->capture[0] <= priv->capture[2])
+		*raw_prd = priv->capture[2] - priv->capture[0];
+	else
+		*raw_prd = priv->max_arr - priv->capture[0] + priv->capture[2];
+
+	/* Duty cycle capture requires at least two capture units */
+	if (pwm->chip->npwm < 2)
+		*raw_dty = 0;
+	else if (priv->capture[0] <= priv->capture[3])
+		*raw_dty = priv->capture[3] - priv->capture[0];
+	else
+		*raw_dty = priv->max_arr - priv->capture[0] + priv->capture[3];
+
+	if (*raw_dty > *raw_prd) {
+		/*
+		 * Race beetween PWM input and DMA: it may happen
+		 * falling edge triggers new capture on TI2/4 before DMA
+		 * had a chance to read CCR2/4. It means capture[1]
+		 * contains period + duty_cycle. So, subtract period.
+		 */
+		*raw_dty -= *raw_prd;
+	}
+
+stop:
+	regmap_update_bits(priv->regmap, TIM_CCER, ccen, 0);
+	regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN, 0);
+
+	return ret;
+}
+
+static int stm32_pwm_capture(struct pwm_chip *chip, struct pwm_device *pwm,
+			     struct pwm_capture *result, unsigned long tmo_ms)
+{
+	struct stm32_pwm *priv = to_stm32_pwm_dev(chip);
+	unsigned long long prd, div, dty;
+	unsigned long rate;
+	unsigned int psc = 0, icpsc, scale;
+	u32 raw_prd, raw_dty;
+	int ret = 0;
+
+	mutex_lock(&priv->lock);
+
+	if (active_channels(priv)) {
+		ret = -EBUSY;
+		goto unlock;
+	}
+
+	ret = clk_enable(priv->clk);
+	if (ret) {
+		dev_err(priv->chip.dev, "failed to enable counter clock\n");
+		goto unlock;
+	}
+
+	rate = clk_get_rate(priv->clk);
+	if (!rate) {
+		ret = -EINVAL;
+		goto clk_dis;
+	}
+
+	/* prescaler: fit timeout window provided by upper layer */
+	div = (unsigned long long)rate * (unsigned long long)tmo_ms;
+	do_div(div, MSEC_PER_SEC);
+	prd = div;
+	while ((div > priv->max_arr) && (psc < MAX_TIM_PSC)) {
+		psc++;
+		div = prd;
+		do_div(div, psc + 1);
+	}
+	regmap_write(priv->regmap, TIM_ARR, priv->max_arr);
+	regmap_write(priv->regmap, TIM_PSC, psc);
+
+	/* Map TI1 or TI2 PWM input to IC1 & IC2 (or TI3/4 to IC3 & IC4) */
+	regmap_update_bits(priv->regmap,
+			   pwm->hwpwm < 2 ? TIM_CCMR1 : TIM_CCMR2,
+			   TIM_CCMR_CC1S | TIM_CCMR_CC2S, pwm->hwpwm & 0x1 ?
+			   TIM_CCMR_CC1S_TI2 | TIM_CCMR_CC2S_TI2 :
+			   TIM_CCMR_CC1S_TI1 | TIM_CCMR_CC2S_TI1);
+
+	/* Capture period on IC1/3 rising edge, duty cycle on IC2/4 falling. */
+	regmap_update_bits(priv->regmap, TIM_CCER, pwm->hwpwm < 2 ?
+			   TIM_CCER_CC12P : TIM_CCER_CC34P, pwm->hwpwm < 2 ?
+			   TIM_CCER_CC2P : TIM_CCER_CC4P);
+
+	ret = stm32_pwm_raw_capture(priv, pwm, tmo_ms, &raw_prd, &raw_dty);
+	if (ret)
+		goto stop;
+
+	/*
+	 * Got a capture. Try to improve accuracy at high rates:
+	 * - decrease counter clock prescaler, scale up to max rate.
+	 * - use input prescaler, capture once every /2 /4 or /8 edges.
+	 */
+	if (raw_prd) {
+		u32 max_arr = priv->max_arr - 0x1000; /* arbitrary margin */
+
+		scale = max_arr / min(max_arr, raw_prd);
+	} else {
+		scale = priv->max_arr; /* bellow resolution, use max scale */
+	}
+
+	if (psc && scale > 1) {
+		/* 2nd measure with new scale */
+		psc /= scale;
+		regmap_write(priv->regmap, TIM_PSC, psc);
+		ret = stm32_pwm_raw_capture(priv, pwm, tmo_ms, &raw_prd,
+					    &raw_dty);
+		if (ret)
+			goto stop;
+	}
+
+	/* Compute intermediate period not to exceed timeout at low rates */
+	prd = (unsigned long long)raw_prd * (psc + 1) * NSEC_PER_SEC;
+	do_div(prd, rate);
+
+	for (icpsc = 0; icpsc < MAX_TIM_ICPSC ; icpsc++) {
+		/* input prescaler: also keep arbitrary margin */
+		if (raw_prd >= (priv->max_arr - 0x1000) >> (icpsc + 1))
+			break;
+		if (prd >= (tmo_ms * NSEC_PER_MSEC) >> (icpsc + 2))
+			break;
+	}
+
+	if (!icpsc)
+		goto done;
+
+	/* Last chance to improve period accuracy, using input prescaler */
+	regmap_update_bits(priv->regmap,
+			   pwm->hwpwm < 2 ? TIM_CCMR1 : TIM_CCMR2,
+			   TIM_CCMR_IC1PSC | TIM_CCMR_IC2PSC,
+			   FIELD_PREP(TIM_CCMR_IC1PSC, icpsc) |
+			   FIELD_PREP(TIM_CCMR_IC2PSC, icpsc));
+
+	ret = stm32_pwm_raw_capture(priv, pwm, tmo_ms, &raw_prd, &raw_dty);
+	if (ret)
+		goto stop;
+
+	if (raw_dty >= (raw_prd >> icpsc)) {
+		/*
+		 * We may fall here using input prescaler, when input
+		 * capture starts on high side (before falling edge).
+		 * Example with icpsc to capture on each 4 events:
+		 *
+		 *       start   1st capture                     2nd capture
+		 *         v     v                               v
+		 *         ___   _____   _____   _____   _____   ____
+		 * TI1..4     |__|    |__|    |__|    |__|    |__|
+		 *            v  v    .  .    .  .    .       v  v
+		 * icpsc1/3:  .  0    .  1    .  2    .  3    .  0
+		 * icpsc2/4:  0       1       2       3       0
+		 *            v  v                            v  v
+		 * CCR1/3  ......t0..............................t2
+		 * CCR2/4  ..t1..............................t1'...
+		 *               .                            .  .
+		 * Capture0:     .<----------------------------->.
+		 * Capture1:     .<-------------------------->.  .
+		 *               .                            .  .
+		 * Period:       .<------>                    .  .
+		 * Low side:                                  .<>.
+		 *
+		 * Result:
+		 * - Period = Capture0 / icpsc
+		 * - Duty = Period - Low side = Period - (Capture0 - Capture1)
+		 */
+		raw_dty = (raw_prd >> icpsc) - (raw_prd - raw_dty);
+	}
+
+done:
+	prd = (unsigned long long)raw_prd * (psc + 1) * NSEC_PER_SEC;
+	result->period = DIV_ROUND_UP_ULL(prd, rate << icpsc);
+	dty = (unsigned long long)raw_dty * (psc + 1) * NSEC_PER_SEC;
+	result->duty_cycle = DIV_ROUND_UP_ULL(dty, rate);
+stop:
+	regmap_write(priv->regmap, TIM_CCER, 0);
+	regmap_write(priv->regmap, pwm->hwpwm < 2 ? TIM_CCMR1 : TIM_CCMR2, 0);
+	regmap_write(priv->regmap, TIM_PSC, 0);
+clk_dis:
+	clk_disable(priv->clk);
+unlock:
+	mutex_unlock(&priv->lock);
+
+	return ret;
+}
+
 static int stm32_pwm_config(struct stm32_pwm *priv, int ch,
 			    int duty_ns, int period_ns)
 {
@@ -230,6 +484,9 @@ static int stm32_pwm_apply_locked(struct pwm_chip *chip, struct pwm_device *pwm,
 static const struct pwm_ops stm32pwm_ops = {
 	.owner = THIS_MODULE,
 	.apply = stm32_pwm_apply_locked,
+#if IS_ENABLED(CONFIG_DMA_ENGINE)
+	.capture = stm32_pwm_capture,
+#endif
 };
 
 static int stm32_pwm_set_breakinput(struct stm32_pwm *priv,

include/linux/mfd/stm32-timers.h

@@ -8,6 +8,8 @@
 #define _LINUX_STM32_GPTIMER_H_
 
 #include <linux/clk.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
 #include <linux/regmap.h>
 
 #define TIM_CR1		0x00	/* Control Register 1      */
@@ -27,6 +29,8 @@
 #define TIM_CCR3	0x3C	/* Capt/Comp Register 3    */
 #define TIM_CCR4	0x40	/* Capt/Comp Register 4    */
 #define TIM_BDTR	0x44	/* Break and Dead-Time Reg */
+#define TIM_DCR		0x48	/* DMA control register    */
+#define TIM_DMAR	0x4C	/* DMA register for transfer */
 
 #define TIM_CR1_CEN	BIT(0)	/* Counter Enable	   */
 #define TIM_CR1_DIR	BIT(4)  /* Counter Direction	   */
@@ -36,17 +40,35 @@
 #define TIM_SMCR_SMS	(BIT(0) | BIT(1) | BIT(2)) /* Slave mode selection */
 #define TIM_SMCR_TS	(BIT(4) | BIT(5) | BIT(6)) /* Trigger selection */
 #define TIM_DIER_UIE	BIT(0)	/* Update interrupt	   */
+#define TIM_DIER_UDE	BIT(8)  /* Update DMA request Enable */
+#define TIM_DIER_CC1DE	BIT(9)  /* CC1 DMA request Enable  */
+#define TIM_DIER_CC2DE	BIT(10) /* CC2 DMA request Enable  */
+#define TIM_DIER_CC3DE	BIT(11) /* CC3 DMA request Enable  */
+#define TIM_DIER_CC4DE	BIT(12) /* CC4 DMA request Enable  */
+#define TIM_DIER_COMDE	BIT(13) /* COM DMA request Enable  */
+#define TIM_DIER_TDE	BIT(14) /* Trigger DMA request Enable */
 #define TIM_SR_UIF	BIT(0)	/* Update interrupt flag   */
 #define TIM_EGR_UG	BIT(0)	/* Update Generation       */
 #define TIM_CCMR_PE	BIT(3)	/* Channel Preload Enable  */
 #define TIM_CCMR_M1	(BIT(6) | BIT(5))  /* Channel PWM Mode 1 */
+#define TIM_CCMR_CC1S		(BIT(0) | BIT(1)) /* Capture/compare 1 sel */
+#define TIM_CCMR_IC1PSC		GENMASK(3, 2)	/* Input capture 1 prescaler */
+#define TIM_CCMR_CC2S		(BIT(8) | BIT(9)) /* Capture/compare 2 sel */
+#define TIM_CCMR_IC2PSC		GENMASK(11, 10)	/* Input capture 2 prescaler */
+#define TIM_CCMR_CC1S_TI1	BIT(0)	/* IC1/IC3 selects TI1/TI3 */
+#define TIM_CCMR_CC1S_TI2	BIT(1)	/* IC1/IC3 selects TI2/TI4 */
+#define TIM_CCMR_CC2S_TI2	BIT(8)	/* IC2/IC4 selects TI2/TI4 */
+#define TIM_CCMR_CC2S_TI1	BIT(9)	/* IC2/IC4 selects TI1/TI3 */
 #define TIM_CCER_CC1E	BIT(0)	/* Capt/Comp 1  out Ena    */
 #define TIM_CCER_CC1P	BIT(1)	/* Capt/Comp 1  Polarity   */
 #define TIM_CCER_CC1NE	BIT(2)	/* Capt/Comp 1N out Ena    */
 #define TIM_CCER_CC1NP	BIT(3)	/* Capt/Comp 1N Polarity   */
 #define TIM_CCER_CC2E	BIT(4)	/* Capt/Comp 2  out Ena    */
+#define TIM_CCER_CC2P	BIT(5)	/* Capt/Comp 2  Polarity   */
 #define TIM_CCER_CC3E	BIT(8)	/* Capt/Comp 3  out Ena    */
+#define TIM_CCER_CC3P	BIT(9)	/* Capt/Comp 3  Polarity   */
 #define TIM_CCER_CC4E	BIT(12)	/* Capt/Comp 4  out Ena    */
+#define TIM_CCER_CC4P	BIT(13)	/* Capt/Comp 4  Polarity   */
 #define TIM_CCER_CCXE	(BIT(0) | BIT(4) | BIT(8) | BIT(12))
 #define TIM_BDTR_BKE	BIT(12) /* Break input enable	   */
 #define TIM_BDTR_BKP	BIT(13) /* Break input polarity	   */
@@ -56,8 +78,11 @@
 #define TIM_BDTR_BK2F	(BIT(20) | BIT(21) | BIT(22) | BIT(23))
 #define TIM_BDTR_BK2E	BIT(24) /* Break 2 input enable	   */
 #define TIM_BDTR_BK2P	BIT(25) /* Break 2 input polarity  */
+#define TIM_DCR_DBA	GENMASK(4, 0)	/* DMA base addr */
+#define TIM_DCR_DBL	GENMASK(12, 8)	/* DMA burst len */
 
 #define MAX_TIM_PSC		0xFFFF
+#define MAX_TIM_ICPSC		0x3
 #define TIM_CR2_MMS_SHIFT	4
 #define TIM_CR2_MMS2_SHIFT	20
 #define TIM_SMCR_TS_SHIFT	4
@@ -65,9 +90,42 @@
 #define TIM_BDTR_BKF_SHIFT	16
 #define TIM_BDTR_BK2F_SHIFT	20
 
+enum stm32_timers_dmas {
+	STM32_TIMERS_DMA_CH1,
+	STM32_TIMERS_DMA_CH2,
+	STM32_TIMERS_DMA_CH3,
+	STM32_TIMERS_DMA_CH4,
+	STM32_TIMERS_DMA_UP,
+	STM32_TIMERS_DMA_TRIG,
+	STM32_TIMERS_DMA_COM,
+	STM32_TIMERS_MAX_DMAS,
+};
+
+/**
+ * struct stm32_timers_dma - STM32 timer DMA handling.
+ * @completion:		end of DMA transfer completion
+ * @phys_base:		control registers physical base address
+ * @lock:		protect DMA access
+ * @chan:		DMA channel in use
+ * @chans:		DMA channels available for this timer instance
+ */
+struct stm32_timers_dma {
+	struct completion completion;
+	phys_addr_t phys_base;
+	struct mutex lock;
+	struct dma_chan *chan;
+	struct dma_chan *chans[STM32_TIMERS_MAX_DMAS];
+};
+
 struct stm32_timers {
 	struct clk *clk;
 	struct regmap *regmap;
 	u32 max_arr;
+	struct stm32_timers_dma dma; /* Only to be used by the parent */
 };
+
+int stm32_timers_dma_burst_read(struct device *dev, u32 *buf,
+				enum stm32_timers_dmas id, u32 reg,
+				unsigned int num_reg, unsigned int bursts,
+				unsigned long tmo_ms);
 #endif