Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Arnd Bergmann:
 "A few patches have come up since the merge window.  The largest one is
  a rewrite of the PXA lubbock/mainstone IRQ handling.  This was already
  broken in 2011 by a change to the GPIO code and only noticed now.

  The other changes contained here are:

  MAINTAINERS file updates:

   - Ray Jui and Scott Branden are now co-maintainers for some of the
     mach-bcm chips, while Christian Daudt and Marc Carino have stepped
     down.

   - Andrew Victor is no longer maintaining at91.  Instead, Alexandre
     Belloni now becomes an official maintainer, after having done a
     bulk of the work for a while.

   - Baruch Siach, who added the mach-digicolor platform in 4.1 is now
     listed as maintainer

   - The git URL for mach-socfpga has changed

  Bug fixes:

   - Three bug fixes for new rockchip rk3288 code

   - A regression fix to make SD card support work on certain ux500
     boards

   - multiple smaller dts fixes for imx, omap, mvebu, and shmobile

   - a regression fiix for omap3 power consumption

   - a fix for regression in the ARM CCI bus driver

  Configuration changes:

   - more imx platforms are now enabled in multi_v7_defconfig"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
  MAINTAINERS: add Conexant Digicolor machines entry
  MAINTAINERS: socfpga: update the git repo for SoCFPGA
  ARM: multi_v7_defconfig: Select more FSL SoCs
  MAINTAINERS: replace an AT91 maintainer
  drivers: CCI: fix used_mask init in validate_group()
  bus: omap_l3_noc: Fix master id address decoding for OMAP5
  bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
  ARM: dts: dra7: Fix efuse register size for ABB
  ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
  ARM: dts: am57xx-beagle-x15: Switch UART mux pins
  ARM: dts: am437x-sk: reduce col-scan-delay-us
  ARM: dts: am437x-sk: fix for new newhaven display module revision
  ARM: dts: am57xx-beagle-x15: Fix RTC aliases
  ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
  ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
  ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
  ARM: dts: OMAP3-N900: Add microphone bias voltages
  ARM: OMAP2+: Fix omap off idle power consumption creeping up
  MAINTAINERS: Update brcmstb entry
  MAINTAINERS: Remove Christian Daudt for mach-bcm
  ...

CREDITS

@@ -3709,6 +3709,13 @@ N: Dirk Verworner
 D: Co-author of German book ``Linux-Kernel-Programmierung''
 D: Co-founder of Berlin Linux User Group
 
+N: Andrew Victor
+E: linux@maxim.org.za
+W: http://maxim.org.za/at91_26.html
+D: First maintainer of Atmel ARM-based SoC, aka AT91
+D: Introduced support for at91rm9200, the first chip of AT91 family
+S: South Africa
+
 N: Riku Voipio
 E: riku.voipio@iki.fi
 D: Author of PCA9532 LED and Fintek f75375s hwmon driver

Documentation/devicetree/bindings/arm/omap/l3-noc.txt

@@ -6,6 +6,7 @@ provided by Arteris.
 Required properties:
 - compatible : Should be "ti,omap3-l3-smx" for OMAP3 family
                Should be "ti,omap4-l3-noc" for OMAP4 family
+               Should be "ti,omap5-l3-noc" for OMAP5 family
 	       Should be "ti,dra7-l3-noc" for DRA7 family
                Should be "ti,am4372-l3-noc" for AM43 family
 - reg:	Contains L3 register address range for each noc domain.

Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt

@@ -38,7 +38,7 @@ dma_apbx: dma-apbx@80024000 {
 		      80 81 68 69
 		      70 71 72 73
 		      74 75 76 77>;
-	interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty",
+	interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty",
 			  "saif0", "saif1", "i2c0", "i2c1",
 			  "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
 			  "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";

MAINTAINERS

@@ -892,11 +892,10 @@ S:	Maintained
 F:	arch/arm/mach-alpine/
 
 ARM/ATMEL AT91RM9200 AND AT91SAM ARM ARCHITECTURES
-M:	Andrew Victor <linux@maxim.org.za>
 M:	Nicolas Ferre <nicolas.ferre@atmel.com>
+M:	Alexandre Belloni <alexandre.belloni@free-electrons.com>
 M:	Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
-W:	http://maxim.org.za/at91_26.html
 W:	http://www.linux4sam.org
 S:	Supported
 F:	arch/arm/mach-at91/
@@ -990,6 +989,12 @@ F:	drivers/clocksource/timer-prima2.c
 F:	drivers/clocksource/timer-atlas7.c
 N:	[^a-z]sirf
 
+ARM/CONEXANT DIGICOLOR MACHINE SUPPORT
+M:	Baruch Siach <baruch@tkos.co.il>
+L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S:	Maintained
+N:	digicolor
+
 ARM/EBSA110 MACHINE SUPPORT
 M:	Russell King <linux@arm.linux.org.uk>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -1439,9 +1444,10 @@ ARM/SOCFPGA ARCHITECTURE
 M:	Dinh Nguyen <dinguyen@opensource.altera.com>
 S:	Maintained
 F:	arch/arm/mach-socfpga/
+F:	arch/arm/boot/dts/socfpga*
+F:	arch/arm/configs/socfpga_defconfig
 W:	http://www.rocketboards.org
-T:	git://git.rocketboards.org/linux-socfpga.git
-T:	git://git.rocketboards.org/linux-socfpga-next.git
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux.git
 
 ARM/SOCFPGA CLOCK FRAMEWORK SUPPORT
 M:	Dinh Nguyen <dinguyen@opensource.altera.com>
@@ -2116,8 +2122,9 @@ S:	Supported
 F:	drivers/net/ethernet/broadcom/bnx2x/
 
 BROADCOM BCM281XX/BCM11XXX/BCM216XX ARM ARCHITECTURE
-M:	Christian Daudt <bcm@fixthebug.org>
 M:	Florian Fainelli <f.fainelli@gmail.com>
+M:	Ray Jui <rjui@broadcom.com>
+M:	Scott Branden <sbranden@broadcom.com>
 L:	bcm-kernel-feedback-list@broadcom.com
 T:	git git://github.com/broadcom/mach-bcm
 S:	Maintained
@@ -2168,7 +2175,6 @@ S:	Maintained
 F:	drivers/usb/gadget/udc/bcm63xx_udc.*
 
 BROADCOM BCM7XXX ARM ARCHITECTURE
-M:	Marc Carino <marc.ceeeee@gmail.com>
 M:	Brian Norris <computersforpeace@gmail.com>
 M:	Gregory Fong <gregory.0xf0@gmail.com>
 M:	Florian Fainelli <f.fainelli@gmail.com>

arch/arm/boot/dts/am437x-sk-evm.dts

@@ -49,7 +49,7 @@
 		pinctrl-0 = <&matrix_keypad_pins>;
 
 		debounce-delay-ms = <5>;
-		col-scan-delay-us = <1500>;
+		col-scan-delay-us = <5>;
 
 		row-gpios = <&gpio5 5 GPIO_ACTIVE_HIGH		/* Bank5, pin5 */
 				&gpio5 6 GPIO_ACTIVE_HIGH>;	/* Bank5, pin6 */
@@ -473,7 +473,7 @@
 		interrupt-parent = <&gpio0>;
 		interrupts = <31 0>;
 
-		wake-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
 
 		touchscreen-size-x = <480>;
 		touchscreen-size-y = <272>;

arch/arm/boot/dts/am57xx-beagle-x15.dts

@@ -18,6 +18,7 @@
 	aliases {
 		rtc0 = &mcp_rtc;
 		rtc1 = &tps659038_rtc;
+		rtc2 = &rtc;
 	};
 
 	memory {
@@ -83,7 +84,7 @@
 	gpio_fan: gpio_fan {
 		/* Based on 5v 500mA AFB02505HHB */
 		compatible = "gpio-fan";
-		gpios =  <&tps659038_gpio 1 GPIO_ACTIVE_HIGH>;
+		gpios =  <&tps659038_gpio 2 GPIO_ACTIVE_HIGH>;
 		gpio-fan,speed-map = <0     0>,
 				     <13000 1>;
 		#cooling-cells = <2>;
@@ -130,8 +131,8 @@
 
 	uart3_pins_default: uart3_pins_default {
 		pinctrl-single,pins = <
-			0x248 (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_rxd.rxd */
-			0x24c (PIN_INPUT_SLEW | MUX_MODE0) /* uart3_txd.txd */
+			0x3f8 (PIN_INPUT_SLEW | MUX_MODE2) /* uart2_ctsn.uart3_rxd */
+			0x3fc (PIN_INPUT_SLEW | MUX_MODE1) /* uart2_rtsn.uart3_txd */
 		>;
 	};
 
@@ -455,7 +456,7 @@
 	mcp_rtc: rtc@6f {
 		compatible = "microchip,mcp7941x";
 		reg = <0x6f>;
-		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_LOW>;  /* IRQ_SYS_1N */
+		interrupts = <GIC_SPI 2 IRQ_TYPE_EDGE_RISING>;  /* IRQ_SYS_1N */
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&mcp79410_pins_default>;
@@ -478,7 +479,7 @@
 &uart3 {
 	status = "okay";
 	interrupts-extended = <&crossbar_mpu GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
-			      <&dra7_pmx_core 0x248>;
+			      <&dra7_pmx_core 0x3f8>;
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart3_pins_default>;

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts

@@ -105,6 +105,10 @@
 		};
 
 		internal-regs {
+			rtc@10300 {
+				/* No crystal connected to the internal RTC */
+				status = "disabled";
+			};
 			serial@12000 {
 				status = "okay";
 			};

arch/arm/boot/dts/dra7.dtsi

@@ -911,7 +911,7 @@
 			ti,clock-cycles = <16>;
 
 			reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
-			      <0x4ae06014 0x4>, <0x4a003b20 0x8>,
+			      <0x4ae06014 0x4>, <0x4a003b20 0xc>,
 			      <0x4ae0c158 0x4>;
 			reg-names = "setup-address", "control-address",
 				    "int-address", "efuse-address",
@@ -944,7 +944,7 @@
 			ti,clock-cycles = <16>;
 
 			reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
-			      <0x4ae06010 0x4>, <0x4a0025cc 0x8>,
+			      <0x4ae06010 0x4>, <0x4a0025cc 0xc>,
 			      <0x4a002470 0x4>;
 			reg-names = "setup-address", "control-address",
 				    "int-address", "efuse-address",
@@ -977,7 +977,7 @@
 			ti,clock-cycles = <16>;
 
 			reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
-			      <0x4ae06010 0x4>, <0x4a0025e0 0x8>,
+			      <0x4ae06010 0x4>, <0x4a0025e0 0xc>,
 			      <0x4a00246c 0x4>;
 			reg-names = "setup-address", "control-address",
 				    "int-address", "efuse-address",
@@ -1010,7 +1010,7 @@
 			ti,clock-cycles = <16>;
 
 			reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
-			      <0x4ae06010 0x4>, <0x4a003b08 0x8>,
+			      <0x4ae06010 0x4>, <0x4a003b08 0xc>,
 			      <0x4ae0c154 0x4>;
 			reg-names = "setup-address", "control-address",
 				    "int-address", "efuse-address",
@@ -1203,7 +1203,7 @@
 			status = "disabled";
 		};
 
-		rtc@48838000 {
+		rtc: rtc@48838000 {
 			compatible = "ti,am3352-rtc";
 			reg = <0x48838000 0x100>;
 			interrupts = <GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH>,

arch/arm/boot/dts/imx23-olinuxino.dts

@@ -12,6 +12,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "imx23.dtsi"
 
 / {
@@ -93,6 +94,7 @@
 
 	ahb@80080000 {
 		usb0: usb@80080000 {
+			dr_mode = "host";
 			vbus-supply = <&reg_usb0_vbus>;
 			status = "okay";
 		};
@@ -122,7 +124,7 @@
 
 		user {
 			label = "green";
-			gpios = <&gpio2 1 1>;
+			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
 		};
 	};
 };

arch/arm/boot/dts/imx25.dtsi

@@ -428,6 +428,7 @@
 
 			pwm4: pwm@53fc8000 {
 				compatible = "fsl,imx25-pwm", "fsl,imx27-pwm";
+				#pwm-cells = <2>;
 				reg = <0x53fc8000 0x4000>;
 				clocks = <&clks 108>, <&clks 52>;
 				clock-names = "ipg", "per";

arch/arm/boot/dts/imx28.dtsi

@@ -913,7 +913,7 @@
 					      80 81 68 69
 					      70 71 72 73
 					      74 75 76 77>;
-				interrupt-names = "auart4-rx", "aurat4-tx", "spdif-tx", "empty",
+				interrupt-names = "auart4-rx", "auart4-tx", "spdif-tx", "empty",
 						  "saif0", "saif1", "i2c0", "i2c1",
 						  "auart0-rx", "auart0-tx", "auart1-rx", "auart1-tx",
 						  "auart2-rx", "auart2-tx", "auart3-rx", "auart3-tx";

arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi

@@ -31,6 +31,7 @@
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio4 15 0>;
+			enable-active-high;
 		};
 
 		reg_usb_h1_vbus: regulator@1 {
@@ -40,6 +41,7 @@
 			regulator-min-microvolt = <5000000>;
 			regulator-max-microvolt = <5000000>;
 			gpio = <&gpio1 0 0>;
+			enable-active-high;
 		};
 	};
 

arch/arm/boot/dts/imx6qdl-sabreauto.dtsi

@@ -185,7 +185,6 @@
 &i2c3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c3>;
-	pinctrl-assert-gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 
 	max7310_a: gpio@30 {

arch/arm/boot/dts/omap3-n900.dts

@@ -498,6 +498,8 @@
 		DRVDD-supply = <&vmmc2>;
 		IOVDD-supply = <&vio>;
 		DVDD-supply = <&vio>;
+
+		ai3x-micbias-vg = <1>;
 	};
 
 	tlv320aic3x_aux: tlv320aic3x@19 {
@@ -509,6 +511,8 @@
 		DRVDD-supply = <&vmmc2>;
 		IOVDD-supply = <&vio>;
 		DVDD-supply = <&vio>;
+
+		ai3x-micbias-vg = <2>;
 	};
 
 	tsl2563: tsl2563@29 {

arch/arm/boot/dts/omap3.dtsi

@@ -456,6 +456,7 @@
 		};
 
 		mmu_isp: mmu@480bd400 {
+			#iommu-cells = <0>;
 			compatible = "ti,omap2-iommu";
 			reg = <0x480bd400 0x80>;
 			interrupts = <24>;
@@ -464,6 +465,7 @@
 		};
 
 		mmu_iva: mmu@5d000000 {
+			#iommu-cells = <0>;
 			compatible = "ti,omap2-iommu";
 			reg = <0x5d000000 0x80>;
 			interrupts = <28>;

arch/arm/boot/dts/omap5.dtsi

@@ -128,7 +128,7 @@
 	 * hierarchy.
 	 */
 	ocp {
-		compatible = "ti,omap4-l3-noc", "simple-bus";
+		compatible = "ti,omap5-l3-noc", "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges;

arch/arm/boot/dts/r8a7791-koelsch.dts

@@ -545,7 +545,7 @@
 		compatible = "adi,adv7511w";
 		reg = <0x39>;
 		interrupt-parent = <&gpio3>;
-		interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
 
 		adi,input-depth = <8>;
 		adi,input-colorspace = "rgb";

arch/arm/boot/dts/ste-dbx5x0.dtsi

@@ -1017,23 +1017,6 @@
 			status = "disabled";
 		};
 
-		vmmci: regulator-gpio {
-			compatible = "regulator-gpio";
-
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <2900000>;
-			regulator-name = "mmci-reg";
-			regulator-type = "voltage";
-
-			startup-delay-us = <100>;
-			enable-active-high;
-
-			states = <1800000 0x1
-				  2900000 0x0>;
-
-			status = "disabled";
-		};
-
 		mcde@a0350000 {
 			compatible = "stericsson,mcde";
 			reg = <0xa0350000 0x1000>, /* MCDE */

arch/arm/boot/dts/ste-href.dtsi

@@ -111,6 +111,21 @@
 			pinctrl-1 = <&i2c3_sleep_mode>;
 		};
 
+		vmmci: regulator-gpio {
+			compatible = "regulator-gpio";
+
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2900000>;
+			regulator-name = "mmci-reg";
+			regulator-type = "voltage";
+
+			startup-delay-us = <100>;
+			enable-active-high;
+
+			states = <1800000 0x1
+				  2900000 0x0>;
+		};
+
 		// External Micro SD slot
 		sdi0_per1@80126000 {
 			arm,primecell-periphid = <0x10480180>;

arch/arm/boot/dts/ste-snowball.dts

@@ -146,8 +146,21 @@
 		};
 
 		vmmci: regulator-gpio {
+			compatible = "regulator-gpio";
+
 			gpios = <&gpio7 4 0x4>;
 			enable-gpio = <&gpio6 25 0x4>;
+
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2900000>;
+			regulator-name = "mmci-reg";
+			regulator-type = "voltage";
+
+			startup-delay-us = <100>;
+			enable-active-high;
+
+			states = <1800000 0x1
+				  2900000 0x0>;
 		};
 
 		// External Micro SD slot

arch/arm/configs/multi_v7_defconfig

@@ -39,11 +39,14 @@ CONFIG_ARCH_HIP04=y
 CONFIG_ARCH_KEYSTONE=y
 CONFIG_ARCH_MESON=y
 CONFIG_ARCH_MXC=y
+CONFIG_SOC_IMX50=y
 CONFIG_SOC_IMX51=y
 CONFIG_SOC_IMX53=y
 CONFIG_SOC_IMX6Q=y
 CONFIG_SOC_IMX6SL=y
+CONFIG_SOC_IMX6SX=y
 CONFIG_SOC_VF610=y
+CONFIG_SOC_LS1021A=y
 CONFIG_ARCH_OMAP3=y
 CONFIG_ARCH_OMAP4=y
 CONFIG_SOC_OMAP5=y

arch/arm/configs/omap2plus_defconfig

@@ -393,7 +393,7 @@ CONFIG_TI_EDMA=y
 CONFIG_DMA_OMAP=y
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_EXTCON=m
-CONFIG_EXTCON_GPIO=m
+CONFIG_EXTCON_USB_GPIO=m
 CONFIG_EXTCON_PALMAS=m
 CONFIG_TI_EMIF=m
 CONFIG_PWM=y

arch/arm/mach-imx/devices/platform-sdhci-esdhc-imx.c

@@ -1,5 +1,5 @@
 /*
- * Copyright (C) 2010 Pengutronix, Wolfram Sang <w.sang@pengutronix.de>
+ * Copyright (C) 2010 Pengutronix, Wolfram Sang <kernel@pengutronix.de>
  *
  * This program is free software; you can redistribute it and/or modify it under
  * the terms of the GNU General Public License version 2 as published by the

arch/arm/mach-omap2/prm-regbits-34xx.h

@@ -112,6 +112,7 @@
 #define OMAP3430_VC_CMD_ONLP_SHIFT			16
 #define OMAP3430_VC_CMD_RET_SHIFT			8
 #define OMAP3430_VC_CMD_OFF_SHIFT			0
+#define OMAP3430_SREN_MASK				(1 << 4)
 #define OMAP3430_HSEN_MASK				(1 << 3)
 #define OMAP3430_MCODE_MASK				(0x7 << 0)
 #define OMAP3430_VALID_MASK				(1 << 24)

arch/arm/mach-omap2/prm-regbits-44xx.h

@@ -35,6 +35,7 @@
 #define OMAP4430_GLOBAL_WARM_SW_RST_SHIFT				1
 #define OMAP4430_GLOBAL_WUEN_MASK					(1 << 16)
 #define OMAP4430_HSMCODE_MASK						(0x7 << 0)
+#define OMAP4430_SRMODEEN_MASK						(1 << 4)
 #define OMAP4430_HSMODEEN_MASK						(1 << 3)
 #define OMAP4430_HSSCLL_SHIFT						24
 #define OMAP4430_ICEPICK_RST_SHIFT					9

arch/arm/mach-omap2/vc.c

@@ -316,7 +316,8 @@ static void __init omap3_vc_init_pmic_signaling(struct voltagedomain *voltdm)
 	 * idle. And we can also scale voltages to zero for off-idle.
 	 * Note that no actual voltage scaling during off-idle will
 	 * happen unless the board specific twl4030 PMIC scripts are
-	 * loaded.
+	 * loaded. See also omap_vc_i2c_init for comments regarding
+	 * erratum i531.
 	 */
 	val = voltdm->read(OMAP3_PRM_VOLTCTRL_OFFSET);
 	if (!(val & OMAP3430_PRM_VOLTCTRL_SEL_OFF)) {
@@ -704,9 +705,16 @@ static void __init omap_vc_i2c_init(struct voltagedomain *voltdm)
 		return;
 	}
 
+	/*
+	 * Note that for omap3 OMAP3430_SREN_MASK clears SREN to work around
+	 * erratum i531 "Extra Power Consumed When Repeated Start Operation
+	 * Mode Is Enabled on I2C Interface Dedicated for Smart Reflex (I2C4)".
+	 * Otherwise I2C4 eventually leads into about 23mW extra power being
+	 * consumed even during off idle using VMODE.
+	 */
 	i2c_high_speed = voltdm->pmic->i2c_high_speed;
 	if (i2c_high_speed)
-		voltdm->rmw(vc->common->i2c_cfg_hsen_mask,
+		voltdm->rmw(vc->common->i2c_cfg_clear_mask,
 			    vc->common->i2c_cfg_hsen_mask,
 			    vc->common->i2c_cfg_reg);
 

arch/arm/mach-omap2/vc.h

@@ -34,6 +34,7 @@ struct voltagedomain;
  * @cmd_ret_shift: RET field shift in PRM_VC_CMD_VAL_* register
  * @cmd_off_shift: OFF field shift in PRM_VC_CMD_VAL_* register
  * @i2c_cfg_reg: I2C configuration register offset
+ * @i2c_cfg_clear_mask: high-speed mode bit clear mask in I2C config register
  * @i2c_cfg_hsen_mask: high-speed mode bit field mask in I2C config register
  * @i2c_mcode_mask: MCODE field mask for I2C config register
  *
@@ -52,6 +53,7 @@ struct omap_vc_common {
 	u8 cmd_ret_shift;
 	u8 cmd_off_shift;
 	u8 i2c_cfg_reg;
+	u8 i2c_cfg_clear_mask;
 	u8 i2c_cfg_hsen_mask;
 	u8 i2c_mcode_mask;
 };

arch/arm/mach-omap2/vc3xxx_data.c

@@ -40,6 +40,7 @@ static struct omap_vc_common omap3_vc_common = {
 	.cmd_onlp_shift	 = OMAP3430_VC_CMD_ONLP_SHIFT,
 	.cmd_ret_shift	 = OMAP3430_VC_CMD_RET_SHIFT,
 	.cmd_off_shift	 = OMAP3430_VC_CMD_OFF_SHIFT,
+	.i2c_cfg_clear_mask = OMAP3430_SREN_MASK | OMAP3430_HSEN_MASK,
 	.i2c_cfg_hsen_mask = OMAP3430_HSEN_MASK,
 	.i2c_cfg_reg	 = OMAP3_PRM_VC_I2C_CFG_OFFSET,
 	.i2c_mcode_mask	 = OMAP3430_MCODE_MASK,

arch/arm/mach-omap2/vc44xx_data.c

@@ -42,6 +42,7 @@ static const struct omap_vc_common omap4_vc_common = {
 	.cmd_ret_shift = OMAP4430_RET_SHIFT,
 	.cmd_off_shift = OMAP4430_OFF_SHIFT,
 	.i2c_cfg_reg = OMAP4_PRM_VC_CFG_I2C_MODE_OFFSET,
+	.i2c_cfg_clear_mask = OMAP4430_SRMODEEN_MASK | OMAP4430_HSMODEEN_MASK,
 	.i2c_cfg_hsen_mask = OMAP4430_HSMODEEN_MASK,
 	.i2c_mcode_mask	 = OMAP4430_HSMCODE_MASK,
 };

arch/arm/mach-pxa/Kconfig

@@ -691,4 +691,13 @@ config SHARPSL_PM_MAX1111
 config PXA310_ULPI
 	bool
 
+config PXA_SYSTEMS_CPLDS
+	tristate "Motherboard cplds"
+	default ARCH_LUBBOCK || MACH_MAINSTONE
+	help
+	  This driver supports the Lubbock and Mainstone multifunction chip
+	  found on the pxa25x development platform system (Lubbock) and pxa27x
+	  development platform system (Mainstone). This IO board supports the
+	  interrupts handling, ethernet controller, flash chips, etc ...
+
 endif

arch/arm/mach-pxa/Makefile

@@ -90,4 +90,5 @@ obj-$(CONFIG_MACH_RAUMFELD_CONNECTOR)	+= raumfeld.o
 obj-$(CONFIG_MACH_RAUMFELD_SPEAKER)	+= raumfeld.o
 obj-$(CONFIG_MACH_ZIPIT2)	+= z2.o
 
+obj-$(CONFIG_PXA_SYSTEMS_CPLDS)	+= pxa_cplds_irqs.o
 obj-$(CONFIG_TOSA_BT)		+= tosa-bt.o

arch/arm/mach-pxa/include/mach/lubbock.h

@@ -37,7 +37,9 @@
 #define LUB_GP			__LUB_REG(LUBBOCK_FPGA_PHYS + 0x100)
 
 /* Board specific IRQs */
-#define LUBBOCK_IRQ(x)		(IRQ_BOARD_START + (x))
+#define LUBBOCK_NR_IRQS		IRQ_BOARD_START
+
+#define LUBBOCK_IRQ(x)		(LUBBOCK_NR_IRQS + (x))
 #define LUBBOCK_SD_IRQ		LUBBOCK_IRQ(0)
 #define LUBBOCK_SA1111_IRQ	LUBBOCK_IRQ(1)
 #define LUBBOCK_USB_IRQ		LUBBOCK_IRQ(2)  /* usb connect */
@@ -47,8 +49,7 @@
 #define LUBBOCK_USB_DISC_IRQ	LUBBOCK_IRQ(6)  /* usb disconnect */
 #define LUBBOCK_LAST_IRQ	LUBBOCK_IRQ(6)
 
-#define LUBBOCK_SA1111_IRQ_BASE	(IRQ_BOARD_START + 16)
-#define LUBBOCK_NR_IRQS		(IRQ_BOARD_START + 16 + 55)
+#define LUBBOCK_SA1111_IRQ_BASE	(LUBBOCK_NR_IRQS + 32)
 
 #ifndef __ASSEMBLY__
 extern void lubbock_set_misc_wr(unsigned int mask, unsigned int set);

arch/arm/mach-pxa/include/mach/mainstone.h

@@ -120,7 +120,9 @@
 #define MST_PCMCIA_PWR_VCC_50   0x4	   /* voltage VCC = 5.0V */
 
 /* board specific IRQs */
-#define MAINSTONE_IRQ(x)	(IRQ_BOARD_START + (x))
+#define MAINSTONE_NR_IRQS	IRQ_BOARD_START
+
+#define MAINSTONE_IRQ(x)	(MAINSTONE_NR_IRQS + (x))
 #define MAINSTONE_MMC_IRQ	MAINSTONE_IRQ(0)
 #define MAINSTONE_USIM_IRQ	MAINSTONE_IRQ(1)
 #define MAINSTONE_USBC_IRQ	MAINSTONE_IRQ(2)
@@ -136,6 +138,4 @@
 #define MAINSTONE_S1_STSCHG_IRQ	MAINSTONE_IRQ(14)
 #define MAINSTONE_S1_IRQ	MAINSTONE_IRQ(15)
 
-#define MAINSTONE_NR_IRQS	(IRQ_BOARD_START + 16)
-
 #endif

arch/arm/mach-pxa/lubbock.c

@@ -12,6 +12,7 @@
  *  published by the Free Software Foundation.
  */
 #include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -123,84 +124,6 @@ void lubbock_set_misc_wr(unsigned int mask, unsigned int set)
 }
 EXPORT_SYMBOL(lubbock_set_misc_wr);
 
-static unsigned long lubbock_irq_enabled;
-
-static void lubbock_mask_irq(struct irq_data *d)
-{
-	int lubbock_irq = (d->irq - LUBBOCK_IRQ(0));
-	LUB_IRQ_MASK_EN = (lubbock_irq_enabled &= ~(1 << lubbock_irq));
-}
-
-static void lubbock_unmask_irq(struct irq_data *d)
-{
-	int lubbock_irq = (d->irq - LUBBOCK_IRQ(0));
-	/* the irq can be acknowledged only if deasserted, so it's done here */
-	LUB_IRQ_SET_CLR &= ~(1 << lubbock_irq);
-	LUB_IRQ_MASK_EN = (lubbock_irq_enabled |= (1 << lubbock_irq));
-}
-
-static struct irq_chip lubbock_irq_chip = {
-	.name		= "FPGA",
-	.irq_ack	= lubbock_mask_irq,
-	.irq_mask	= lubbock_mask_irq,
-	.irq_unmask	= lubbock_unmask_irq,
-};
-
-static void lubbock_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
-	unsigned long pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
-	do {
-		/* clear our parent irq */
-		desc->irq_data.chip->irq_ack(&desc->irq_data);
-		if (likely(pending)) {
-			irq = LUBBOCK_IRQ(0) + __ffs(pending);
-			generic_handle_irq(irq);
-		}
-		pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
-	} while (pending);
-}
-
-static void __init lubbock_init_irq(void)
-{
-	int irq;
-
-	pxa25x_init_irq();
-
-	/* setup extra lubbock irqs */
-	for (irq = LUBBOCK_IRQ(0); irq <= LUBBOCK_LAST_IRQ; irq++) {
-		irq_set_chip_and_handler(irq, &lubbock_irq_chip,
-					 handle_level_irq);
-		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
-	}
-
-	irq_set_chained_handler(PXA_GPIO_TO_IRQ(0), lubbock_irq_handler);
-	irq_set_irq_type(PXA_GPIO_TO_IRQ(0), IRQ_TYPE_EDGE_FALLING);
-}
-
-#ifdef CONFIG_PM
-
-static void lubbock_irq_resume(void)
-{
-	LUB_IRQ_MASK_EN = lubbock_irq_enabled;
-}
-
-static struct syscore_ops lubbock_irq_syscore_ops = {
-	.resume = lubbock_irq_resume,
-};
-
-static int __init lubbock_irq_device_init(void)
-{
-	if (machine_is_lubbock()) {
-		register_syscore_ops(&lubbock_irq_syscore_ops);
-		return 0;
-	}
-	return -ENODEV;
-}
-
-device_initcall(lubbock_irq_device_init);
-
-#endif
-
 static int lubbock_udc_is_connected(void)
 {
 	return (LUB_MISC_RD & (1 << 9)) == 0;
@@ -383,11 +306,38 @@ static struct platform_device lubbock_flash_device[2] = {
 	},
 };
 
+static struct resource lubbock_cplds_resources[] = {
+	[0] = {
+		.start	= LUBBOCK_FPGA_PHYS + 0xc0,
+		.end	= LUBBOCK_FPGA_PHYS + 0xe0 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= PXA_GPIO_TO_IRQ(0),
+		.end	= PXA_GPIO_TO_IRQ(0),
+		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
+	},
+	[2] = {
+		.start	= LUBBOCK_IRQ(0),
+		.end	= LUBBOCK_IRQ(6),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device lubbock_cplds_device = {
+	.name		= "pxa_cplds_irqs",
+	.id		= -1,
+	.resource	= &lubbock_cplds_resources[0],
+	.num_resources	= 3,
+};
+
+
 static struct platform_device *devices[] __initdata = {
 	&sa1111_device,
 	&smc91x_device,
 	&lubbock_flash_device[0],
 	&lubbock_flash_device[1],
+	&lubbock_cplds_device,
 };
 
 static struct pxafb_mode_info sharp_lm8v31_mode = {
@@ -648,7 +598,7 @@ MACHINE_START(LUBBOCK, "Intel DBPXA250 Development Platform (aka Lubbock)")
 	/* Maintainer: MontaVista Software Inc. */
 	.map_io		= lubbock_map_io,
 	.nr_irqs	= LUBBOCK_NR_IRQS,
-	.init_irq	= lubbock_init_irq,
+	.init_irq	= pxa25x_init_irq,
 	.handle_irq	= pxa25x_handle_irq,
 	.init_time	= pxa_timer_init,
 	.init_machine	= lubbock_init,

arch/arm/mach-pxa/mainstone.c

@@ -13,6 +13,7 @@
  *  published by the Free Software Foundation.
  */
 #include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/init.h>
 #include <linux/platform_device.h>
 #include <linux/syscore_ops.h>
@@ -122,92 +123,6 @@ static unsigned long mainstone_pin_config[] = {
 	GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH,
 };
 
-static unsigned long mainstone_irq_enabled;
-
-static void mainstone_mask_irq(struct irq_data *d)
-{
-	int mainstone_irq = (d->irq - MAINSTONE_IRQ(0));
-	MST_INTMSKENA = (mainstone_irq_enabled &= ~(1 << mainstone_irq));
-}
-
-static void mainstone_unmask_irq(struct irq_data *d)
-{
-	int mainstone_irq = (d->irq - MAINSTONE_IRQ(0));
-	/* the irq can be acknowledged only if deasserted, so it's done here */
-	MST_INTSETCLR &= ~(1 << mainstone_irq);
-	MST_INTMSKENA = (mainstone_irq_enabled |= (1 << mainstone_irq));
-}
-
-static struct irq_chip mainstone_irq_chip = {
-	.name		= "FPGA",
-	.irq_ack	= mainstone_mask_irq,
-	.irq_mask	= mainstone_mask_irq,
-	.irq_unmask	= mainstone_unmask_irq,
-};
-
-static void mainstone_irq_handler(unsigned int irq, struct irq_desc *desc)
-{
-	unsigned long pending = MST_INTSETCLR & mainstone_irq_enabled;
-	do {
-		/* clear useless edge notification */
-		desc->irq_data.chip->irq_ack(&desc->irq_data);
-		if (likely(pending)) {
-			irq = MAINSTONE_IRQ(0) + __ffs(pending);
-			generic_handle_irq(irq);
-		}
-		pending = MST_INTSETCLR & mainstone_irq_enabled;
-	} while (pending);
-}
-
-static void __init mainstone_init_irq(void)
-{
-	int irq;
-
-	pxa27x_init_irq();
-
-	/* setup extra Mainstone irqs */
-	for(irq = MAINSTONE_IRQ(0); irq <= MAINSTONE_IRQ(15); irq++) {
-		irq_set_chip_and_handler(irq, &mainstone_irq_chip,
-					 handle_level_irq);
-		if (irq == MAINSTONE_IRQ(10) || irq == MAINSTONE_IRQ(14))
-			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE | IRQF_NOAUTOEN);
-		else
-			set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
-	}
-	set_irq_flags(MAINSTONE_IRQ(8), 0);
-	set_irq_flags(MAINSTONE_IRQ(12), 0);
-
-	MST_INTMSKENA = 0;
-	MST_INTSETCLR = 0;
-
-	irq_set_chained_handler(PXA_GPIO_TO_IRQ(0), mainstone_irq_handler);
-	irq_set_irq_type(PXA_GPIO_TO_IRQ(0), IRQ_TYPE_EDGE_FALLING);
-}
-
-#ifdef CONFIG_PM
-
-static void mainstone_irq_resume(void)
-{
-	MST_INTMSKENA = mainstone_irq_enabled;
-}
-
-static struct syscore_ops mainstone_irq_syscore_ops = {
-	.resume = mainstone_irq_resume,
-};
-
-static int __init mainstone_irq_device_init(void)
-{
-	if (machine_is_mainstone())
-		register_syscore_ops(&mainstone_irq_syscore_ops);
-
-	return 0;
-}
-
-device_initcall(mainstone_irq_device_init);
-
-#endif
-
-
 static struct resource smc91x_resources[] = {
 	[0] = {
 		.start	= (MST_ETH_PHYS + 0x300),
@@ -487,11 +402,37 @@ static struct platform_device mst_gpio_keys_device = {
 	},
 };
 
+static struct resource mst_cplds_resources[] = {
+	[0] = {
+		.start	= MST_FPGA_PHYS + 0xc0,
+		.end	= MST_FPGA_PHYS + 0xe0 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= PXA_GPIO_TO_IRQ(0),
+		.end	= PXA_GPIO_TO_IRQ(0),
+		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
+	},
+	[2] = {
+		.start	= MAINSTONE_IRQ(0),
+		.end	= MAINSTONE_IRQ(15),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device mst_cplds_device = {
+	.name		= "pxa_cplds_irqs",
+	.id		= -1,
+	.resource	= &mst_cplds_resources[0],
+	.num_resources	= 3,
+};
+
 static struct platform_device *platform_devices[] __initdata = {
 	&smc91x_device,
 	&mst_flash_device[0],
 	&mst_flash_device[1],
 	&mst_gpio_keys_device,
+	&mst_cplds_device,
 };
 
 static struct pxaohci_platform_data mainstone_ohci_platform_data = {
@@ -718,7 +659,7 @@ MACHINE_START(MAINSTONE, "Intel HCDDBBVA0 Development Platform (aka Mainstone)")
 	.atag_offset	= 0x100,	/* BLOB boot parameter setting */
 	.map_io		= mainstone_map_io,
 	.nr_irqs	= MAINSTONE_NR_IRQS,
-	.init_irq	= mainstone_init_irq,
+	.init_irq	= pxa27x_init_irq,
 	.handle_irq	= pxa27x_handle_irq,
 	.init_time	= pxa_timer_init,
 	.init_machine	= mainstone_init,

arch/arm/mach-pxa/pxa_cplds_irqs.c

@@ -0,0 +1,200 @@
+/*
+ * Intel Reference Systems cplds
+ *
+ * Copyright (C) 2014 Robert Jarzmik
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Cplds motherboard driver, supporting lubbock and mainstone SoC board.
+ */
+
+#include <linux/bitops.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/mfd/core.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+
+#define FPGA_IRQ_MASK_EN 0x0
+#define FPGA_IRQ_SET_CLR 0x10
+
+#define CPLDS_NB_IRQ	32
+
+struct cplds {
+	void __iomem *base;
+	int irq;
+	unsigned int irq_mask;
+	struct gpio_desc *gpio0;
+	struct irq_domain *irqdomain;
+};
+
+static irqreturn_t cplds_irq_handler(int in_irq, void *d)
+{
+	struct cplds *fpga = d;
+	unsigned long pending;
+	unsigned int bit;
+
+	pending = readl(fpga->base + FPGA_IRQ_SET_CLR) & fpga->irq_mask;
+	for_each_set_bit(bit, &pending, CPLDS_NB_IRQ)
+		generic_handle_irq(irq_find_mapping(fpga->irqdomain, bit));
+
+	return IRQ_HANDLED;
+}
+
+static void cplds_irq_mask_ack(struct irq_data *d)
+{
+	struct cplds *fpga = irq_data_get_irq_chip_data(d);
+	unsigned int cplds_irq = irqd_to_hwirq(d);
+	unsigned int set, bit = BIT(cplds_irq);
+
+	fpga->irq_mask &= ~bit;
+	writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN);
+	set = readl(fpga->base + FPGA_IRQ_SET_CLR);
+	writel(set & ~bit, fpga->base + FPGA_IRQ_SET_CLR);
+}
+
+static void cplds_irq_unmask(struct irq_data *d)
+{
+	struct cplds *fpga = irq_data_get_irq_chip_data(d);
+	unsigned int cplds_irq = irqd_to_hwirq(d);
+	unsigned int bit = BIT(cplds_irq);
+
+	fpga->irq_mask |= bit;
+	writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN);
+}
+
+static struct irq_chip cplds_irq_chip = {
+	.name		= "pxa_cplds",
+	.irq_mask_ack	= cplds_irq_mask_ack,
+	.irq_unmask	= cplds_irq_unmask,
+	.flags		= IRQCHIP_MASK_ON_SUSPEND | IRQCHIP_SKIP_SET_WAKE,
+};
+
+static int cplds_irq_domain_map(struct irq_domain *d, unsigned int irq,
+				   irq_hw_number_t hwirq)
+{
+	struct cplds *fpga = d->host_data;
+
+	irq_set_chip_and_handler(irq, &cplds_irq_chip, handle_level_irq);
+	irq_set_chip_data(irq, fpga);
+
+	return 0;
+}
+
+static const struct irq_domain_ops cplds_irq_domain_ops = {
+	.xlate = irq_domain_xlate_twocell,
+	.map = cplds_irq_domain_map,
+};
+
+static int cplds_resume(struct platform_device *pdev)
+{
+	struct cplds *fpga = platform_get_drvdata(pdev);
+
+	writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN);
+
+	return 0;
+}
+
+static int cplds_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	struct cplds *fpga;
+	int ret;
+	unsigned int base_irq = 0;
+	unsigned long irqflags = 0;
+
+	fpga = devm_kzalloc(&pdev->dev, sizeof(*fpga), GFP_KERNEL);
+	if (!fpga)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	if (res) {
+		fpga->irq = (unsigned int)res->start;
+		irqflags = res->flags;
+	}
+	if (!fpga->irq)
+		return -ENODEV;
+
+	base_irq = platform_get_irq(pdev, 1);
+	if (base_irq < 0)
+		base_irq = 0;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	fpga->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(fpga->base))
+		return PTR_ERR(fpga->base);
+
+	platform_set_drvdata(pdev, fpga);
+
+	writel(fpga->irq_mask, fpga->base + FPGA_IRQ_MASK_EN);
+	writel(0, fpga->base + FPGA_IRQ_SET_CLR);
+
+	ret = devm_request_irq(&pdev->dev, fpga->irq, cplds_irq_handler,
+			       irqflags, dev_name(&pdev->dev), fpga);
+	if (ret == -ENOSYS)
+		return -EPROBE_DEFER;
+
+	if (ret) {
+		dev_err(&pdev->dev, "couldn't request main irq%d: %d\n",
+			fpga->irq, ret);
+		return ret;
+	}
+
+	irq_set_irq_wake(fpga->irq, 1);
+	fpga->irqdomain = irq_domain_add_linear(pdev->dev.of_node,
+					       CPLDS_NB_IRQ,
+					       &cplds_irq_domain_ops, fpga);
+	if (!fpga->irqdomain)
+		return -ENODEV;
+
+	if (base_irq) {
+		ret = irq_create_strict_mappings(fpga->irqdomain, base_irq, 0,
+						 CPLDS_NB_IRQ);
+		if (ret) {
+			dev_err(&pdev->dev, "couldn't create the irq mapping %d..%d\n",
+				base_irq, base_irq + CPLDS_NB_IRQ);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int cplds_remove(struct platform_device *pdev)
+{
+	struct cplds *fpga = platform_get_drvdata(pdev);
+
+	irq_set_chip_and_handler(fpga->irq, NULL, NULL);
+
+	return 0;
+}
+
+static const struct of_device_id cplds_id_table[] = {
+	{ .compatible = "intel,lubbock-cplds-irqs", },
+	{ .compatible = "intel,mainstone-cplds-irqs", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, cplds_id_table);
+
+static struct platform_driver cplds_driver = {
+	.driver		= {
+		.name	= "pxa_cplds_irqs",
+		.of_match_table = of_match_ptr(cplds_id_table),
+	},
+	.probe		= cplds_probe,
+	.remove		= cplds_remove,
+	.resume		= cplds_resume,
+};
+
+module_platform_driver(cplds_driver);
+
+MODULE_DESCRIPTION("PXA Cplds interrupts driver");
+MODULE_AUTHOR("Robert Jarzmik <robert.jarzmik@free.fr>");
+MODULE_LICENSE("GPL");

arch/arm/mach-rockchip/pm.c

@@ -44,9 +44,11 @@ static void __iomem *rk3288_bootram_base;
 static phys_addr_t rk3288_bootram_phy;
 
 static struct regmap *pmu_regmap;
+static struct regmap *grf_regmap;
 static struct regmap *sgrf_regmap;
 
 static u32 rk3288_pmu_pwr_mode_con;
+static u32 rk3288_grf_soc_con0;
 static u32 rk3288_sgrf_soc_con0;
 
 static inline u32 rk3288_l2_config(void)
@@ -70,11 +72,25 @@ static void rk3288_slp_mode_set(int level)
 {
 	u32 mode_set, mode_set1;
 
+	regmap_read(grf_regmap, RK3288_GRF_SOC_CON0, &rk3288_grf_soc_con0);
+
 	regmap_read(sgrf_regmap, RK3288_SGRF_SOC_CON0, &rk3288_sgrf_soc_con0);
 
 	regmap_read(pmu_regmap, RK3288_PMU_PWRMODE_CON,
 		    &rk3288_pmu_pwr_mode_con);
 
+	/*
+	 * We need set this bit GRF_FORCE_JTAG here, for the debug module,
+	 * otherwise, it may become inaccessible after resume.
+	 * This creates a potential security issue, as the sdmmc pins may
+	 * accept jtag data for a short time during resume if no card is
+	 * inserted.
+	 * But this is of course also true for the regular boot, before we
+	 * turn of the jtag/sdmmc autodetect.
+	 */
+	regmap_write(grf_regmap, RK3288_GRF_SOC_CON0, GRF_FORCE_JTAG |
+		     GRF_FORCE_JTAG_WRITE);
+
 	/*
 	 * SGRF_FAST_BOOT_EN - system to boot from FAST_BOOT_ADDR
 	 * PCLK_WDT_GATE - disable WDT during suspend.
@@ -83,6 +99,13 @@ static void rk3288_slp_mode_set(int level)
 		     SGRF_PCLK_WDT_GATE | SGRF_FAST_BOOT_EN
 		     | SGRF_PCLK_WDT_GATE_WRITE | SGRF_FAST_BOOT_EN_WRITE);
 
+	/*
+	 * The dapswjdp can not auto reset before resume, that cause it may
+	 * access some illegal address during resume. Let's disable it before
+	 * suspend, and the MASKROM will enable it back.
+	 */
+	regmap_write(sgrf_regmap, RK3288_SGRF_CPU_CON0, SGRF_DAPDEVICEEN_WRITE);
+
 	/* booting address of resuming system is from this register value */
 	regmap_write(sgrf_regmap, RK3288_SGRF_FAST_BOOT_ADDR,
 		     rk3288_bootram_phy);
@@ -128,6 +151,9 @@ static void rk3288_slp_mode_set_resume(void)
 	regmap_write(sgrf_regmap, RK3288_SGRF_SOC_CON0,
 		     rk3288_sgrf_soc_con0 | SGRF_PCLK_WDT_GATE_WRITE
 		     | SGRF_FAST_BOOT_EN_WRITE);
+
+	regmap_write(grf_regmap, RK3288_GRF_SOC_CON0, rk3288_grf_soc_con0 |
+		     GRF_FORCE_JTAG_WRITE);
 }
 
 static int rockchip_lpmode_enter(unsigned long arg)
@@ -186,6 +212,13 @@ static int rk3288_suspend_init(struct device_node *np)
 		return PTR_ERR(pmu_regmap);
 	}
 
+	grf_regmap = syscon_regmap_lookup_by_compatible(
+				"rockchip,rk3288-grf");
+	if (IS_ERR(grf_regmap)) {
+		pr_err("%s: could not find grf regmap\n", __func__);
+		return PTR_ERR(pmu_regmap);
+	}
+
 	sram_np = of_find_compatible_node(NULL, NULL,
 					  "rockchip,rk3288-pmu-sram");
 	if (!sram_np) {

arch/arm/mach-rockchip/pm.h

@@ -48,6 +48,10 @@ static inline void rockchip_suspend_init(void)
 #define RK3288_PMU_WAKEUP_RST_CLR_CNT	0x44
 #define RK3288_PMU_PWRMODE_CON1		0x90
 
+#define RK3288_GRF_SOC_CON0		0x244
+#define GRF_FORCE_JTAG			BIT(12)
+#define GRF_FORCE_JTAG_WRITE		BIT(28)
+
 #define RK3288_SGRF_SOC_CON0		(0x0000)
 #define RK3288_SGRF_FAST_BOOT_ADDR	(0x0120)
 #define SGRF_PCLK_WDT_GATE		BIT(6)
@@ -55,6 +59,10 @@ static inline void rockchip_suspend_init(void)
 #define SGRF_FAST_BOOT_EN		BIT(8)
 #define SGRF_FAST_BOOT_EN_WRITE		BIT(24)
 
+#define RK3288_SGRF_CPU_CON0		(0x40)
+#define SGRF_DAPDEVICEEN		BIT(0)
+#define SGRF_DAPDEVICEEN_WRITE		BIT(16)
+
 #define RK3288_CRU_MODE_CON		0x50
 #define RK3288_CRU_SEL0_CON		0x60
 #define RK3288_CRU_SEL1_CON		0x64

arch/arm/mach-rockchip/rockchip.c

@@ -30,11 +30,30 @@
 #include "pm.h"
 
 #define RK3288_GRF_SOC_CON0 0x244
+#define RK3288_TIMER6_7_PHYS 0xff810000
 
 static void __init rockchip_timer_init(void)
 {
 	if (of_machine_is_compatible("rockchip,rk3288")) {
 		struct regmap *grf;
+		void __iomem *reg_base;
+
+		/*
+		 * Most/all uboot versions for rk3288 don't enable timer7
+		 * which is needed for the architected timer to work.
+		 * So make sure it is running during early boot.
+		 */
+		reg_base = ioremap(RK3288_TIMER6_7_PHYS, SZ_16K);
+		if (reg_base) {
+			writel(0, reg_base + 0x30);
+			writel(0xffffffff, reg_base + 0x20);
+			writel(0xffffffff, reg_base + 0x24);
+			writel(1, reg_base + 0x30);
+			dsb();
+			iounmap(reg_base);
+		} else {
+			pr_err("rockchip: could not map timer7 registers\n");
+		}
 
 		/*
 		 * Disable auto jtag/sdmmc switching that causes issues

drivers/bus/arm-cci.c

@@ -660,7 +660,7 @@ validate_group(struct perf_event *event)
 		 * Initialise the fake PMU. We only need to populate the
 		 * used_mask for the purposes of validation.
 		 */
-		.used_mask = CPU_BITS_NONE,
+		.used_mask = { 0 },
 	};
 
 	if (!validate_event(event->pmu, &fake_pmu, leader))

drivers/bus/omap_l3_noc.c

@@ -1,7 +1,7 @@
 /*
  * OMAP L3 Interconnect error handling driver
  *
- * Copyright (C) 2011-2014 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2015 Texas Instruments Incorporated - http://www.ti.com/
  *	Santosh Shilimkar <santosh.shilimkar@ti.com>
  *	Sricharan <r.sricharan@ti.com>
  *
@@ -233,7 +233,8 @@ static irqreturn_t l3_interrupt_handler(int irq, void *_l3)
 }
 
 static const struct of_device_id l3_noc_match[] = {
-	{.compatible = "ti,omap4-l3-noc", .data = &omap_l3_data},
+	{.compatible = "ti,omap4-l3-noc", .data = &omap4_l3_data},
+	{.compatible = "ti,omap5-l3-noc", .data = &omap5_l3_data},
 	{.compatible = "ti,dra7-l3-noc", .data = &dra_l3_data},
 	{.compatible = "ti,am4372-l3-noc", .data = &am4372_l3_data},
 	{},

drivers/bus/omap_l3_noc.h

@@ -1,7 +1,7 @@
 /*
  * OMAP L3 Interconnect  error handling driver header
  *
- * Copyright (C) 2011-2014 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2011-2015 Texas Instruments Incorporated - http://www.ti.com/
  *	Santosh Shilimkar <santosh.shilimkar@ti.com>
  *	sricharan <r.sricharan@ti.com>
  *
@@ -175,16 +175,14 @@ static struct l3_flagmux_data omap_l3_flagmux_clk2 = {
 };
 
 
-static struct l3_target_data omap_l3_target_data_clk3[] = {
-	{0x0100, "EMUSS",},
-	{0x0300, "DEBUG SOURCE",},
-	{0x0,	"HOST CLK3",},
+static struct l3_target_data omap4_l3_target_data_clk3[] = {
+	{0x0100, "DEBUGSS",},
 };
 
-static struct l3_flagmux_data omap_l3_flagmux_clk3 = {
+static struct l3_flagmux_data omap4_l3_flagmux_clk3 = {
 	.offset = 0x0200,
-	.l3_targ = omap_l3_target_data_clk3,
-	.num_targ_data = ARRAY_SIZE(omap_l3_target_data_clk3),
+	.l3_targ = omap4_l3_target_data_clk3,
+	.num_targ_data = ARRAY_SIZE(omap4_l3_target_data_clk3),
 };
 
 static struct l3_masters_data omap_l3_masters[] = {
@@ -215,21 +213,49 @@ static struct l3_masters_data omap_l3_masters[] = {
 	{ 0x32, "USBHOSTFS"}
 };
 
-static struct l3_flagmux_data *omap_l3_flagmux[] = {
+static struct l3_flagmux_data *omap4_l3_flagmux[] = {
 	&omap_l3_flagmux_clk1,
 	&omap_l3_flagmux_clk2,
-	&omap_l3_flagmux_clk3,
+	&omap4_l3_flagmux_clk3,
 };
 
-static const struct omap_l3 omap_l3_data = {
-	.l3_flagmux = omap_l3_flagmux,
-	.num_modules = ARRAY_SIZE(omap_l3_flagmux),
+static const struct omap_l3 omap4_l3_data = {
+	.l3_flagmux = omap4_l3_flagmux,
+	.num_modules = ARRAY_SIZE(omap4_l3_flagmux),
 	.l3_masters = omap_l3_masters,
 	.num_masters = ARRAY_SIZE(omap_l3_masters),
 	/* The 6 MSBs of register field used to distinguish initiator */
 	.mst_addr_mask = 0xFC,
 };
 
+/* OMAP5 data */
+static struct l3_target_data omap5_l3_target_data_clk3[] = {
+	{0x0100, "L3INSTR",},
+	{0x0300, "DEBUGSS",},
+	{0x0,	 "HOSTCLK3",},
+};
+
+static struct l3_flagmux_data omap5_l3_flagmux_clk3 = {
+	.offset = 0x0200,
+	.l3_targ = omap5_l3_target_data_clk3,
+	.num_targ_data = ARRAY_SIZE(omap5_l3_target_data_clk3),
+};
+
+static struct l3_flagmux_data *omap5_l3_flagmux[] = {
+	&omap_l3_flagmux_clk1,
+	&omap_l3_flagmux_clk2,
+	&omap5_l3_flagmux_clk3,
+};
+
+static const struct omap_l3 omap5_l3_data = {
+	.l3_flagmux = omap5_l3_flagmux,
+	.num_modules = ARRAY_SIZE(omap5_l3_flagmux),
+	.l3_masters = omap_l3_masters,
+	.num_masters = ARRAY_SIZE(omap_l3_masters),
+	/* The 6 MSBs of register field used to distinguish initiator */
+	.mst_addr_mask = 0x7E0,
+};
+
 /* DRA7 data */
 static struct l3_target_data dra_l3_target_data_clk1[] = {
 	{0x2a00, "AES1",},
@@ -274,7 +300,7 @@ static struct l3_flagmux_data dra_l3_flagmux_clk1 = {
 
 static struct l3_target_data dra_l3_target_data_clk2[] = {
 	{0x0,	"HOST CLK1",},
-	{0x0,	"HOST CLK2",},
+	{0x800000, "HOST CLK2",},
 	{0xdead, L3_TARGET_NOT_SUPPORTED,},
 	{0x3400, "SHA2_2",},
 	{0x0900, "BB2D",},