Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM soc driver specific changes from Olof Johansson:
 - A long-coming conversion of various platforms to a common LED
   infrastructure
 - AT91 is moved over to use the newer MCI driver for MMC
 - Pincontrol conversions for samsung platforms
 - DT bindings for gscaler on samsung
 - i2c driver fixes for tegra, acked by i2c maintainer

Fix up conflicts as per Olof.

* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
  drivers: bus: omap_l3: use resources instead of hardcoded irqs
  pinctrl: exynos: Fix wakeup IRQ domain registration check
  pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
  pinctrl: exynos: Correct the detection of wakeup-eint node
  pinctrl: exynos: Mark exynos_irq_demux_eint as inline
  pinctrl: exynos: Handle only unmasked wakeup interrupts
  pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
  pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
  drivers: bus: Move the OMAP interconnect driver to drivers/bus/
  i2c: tegra: dynamically control fast clk
  i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
  ARM: tegra: clock: remove unused clock entry for i2c
  ARM: tegra: clock: add connection name in i2c clock entry
  i2c: tegra: pass proper name for getting clock
  ARM: tegra: clock: add i2c fast clock entry in clock table
  ARM: EXYNOS: Adds G-Scaler device from Device Tree
  ARM: EXYNOS: Add clock support for G-Scaler
  ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
  ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
  ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
  ...

Documentation/devicetree/bindings/bus/omap-ocp2scp.txt

@@ -0,0 +1,10 @@
+* OMAP OCP2SCP - ocp interface to scp interface
+
+properties:
+- compatible : Should be "ti,omap-ocp2scp"
+- #address-cells, #size-cells : Must be present if the device has sub-nodes
+- ranges : the child address space are mapped 1:1 onto the parent address space
+- ti,hwmods : must be "ocp2scp_usb_phy"
+
+Sub-nodes:
+All the devices connected to ocp2scp are described using sub-node to ocp2scp

Documentation/devicetree/bindings/media/exynos5-gsc.txt

@@ -0,0 +1,30 @@
+* Samsung Exynos5 G-Scaler device
+
+G-Scaler is used for scaling and color space conversion on EXYNOS5 SoCs.
+
+Required properties:
+- compatible: should be "samsung,exynos5-gsc"
+- reg: should contain G-Scaler physical address location and length.
+- interrupts: should contain G-Scaler interrupt number
+
+Example:
+
+gsc_0:  gsc@0x13e00000 {
+	compatible = "samsung,exynos5-gsc";
+	reg = <0x13e00000 0x1000>;
+	interrupts = <0 85 0>;
+};
+
+Aliases:
+Each G-Scaler node should have a numbered alias in the aliases node,
+in the form of gscN, N = 0...3. G-Scaler driver uses these aliases
+to retrieve the device IDs using "of_alias_get_id()" call.
+
+Example:
+
+aliases {
+	gsc0 =&gsc_0;
+	gsc1 =&gsc_1;
+	gsc2 =&gsc_2;
+	gsc3 =&gsc_3;
+};

Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt

@@ -0,0 +1,196 @@
+Samsung GPIO and Pin Mux/Config controller
+
+Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware
+controller. It controls the input/output settings on the available pads/pins
+and also provides ability to multiplex and configure the output of various
+on-chip controllers onto these pads.
+
+Required Properties:
+- compatible: should be one of the following.
+  - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller.
+  - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller.
+
+- reg: Base address of the pin controller hardware module and length of
+  the address space it occupies.
+
+- interrupts: interrupt specifier for the controller. The format and value of
+  the interrupt specifier depends on the interrupt parent for the controller.
+
+- Pin mux/config groups as child nodes: The pin mux (selecting pin function
+  mode) and pin config (pull up/down, driver strength) settings are represented
+  as child nodes of the pin-controller node. There should be atleast one
+  child node and there is no limit on the count of these child nodes.
+
+  The child node should contain a list of pin(s) on which a particular pin
+  function selection or pin configuration (or both) have to applied. This
+  list of pins is specified using the property name "samsung,pins". There
+  should be atleast one pin specfied for this property and there is no upper
+  limit on the count of pins that can be specified. The pins are specified
+  using pin names which are derived from the hardware manual of the SoC. As
+  an example, the pins in GPA0 bank of the pin controller can be represented
+  as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case.
+  The format of the pin names should be (as per the hardware manual)
+  "[pin bank name]-[pin number within the bank]".
+
+  The pin function selection that should be applied on the pins listed in the
+  child node is specified using the "samsung,pin-function" property. The value
+  of this property that should be applied to each of the pins listed in the
+  "samsung,pins" property should be picked from the hardware manual of the SoC
+  for the specified pin group. This property is optional in the child node if
+  no specific function selection is desired for the pins listed in the child
+  node. The value of this property is used as-is to program the pin-controller
+  function selector register of the pin-bank.
+
+  The child node can also optionally specify one or more of the pin
+  configuration that should be applied on all the pins listed in the
+  "samsung,pins" property of the child node. The following pin configuration
+  properties are supported.
+
+  - samsung,pin-pud: Pull up/down configuration.
+  - samsung,pin-drv: Drive strength configuration.
+  - samsung,pin-pud-pdn: Pull up/down configuration in power down mode.
+  - samsung,pin-drv-pdn: Drive strength configuration in power down mode.
+
+  The values specified by these config properties should be derived from the
+  hardware manual and these values are programmed as-is into the pin
+  pull up/down and driver strength register of the pin-controller.
+
+  Note: A child should include atleast a pin function selection property or
+  pin configuration property (one or more) or both.
+
+  The client nodes that require a particular pin function selection and/or
+  pin configuration should use the bindings listed in the "pinctrl-bindings.txt"
+  file.
+
+External GPIO and Wakeup Interrupts:
+
+The controller supports two types of external interrupts over gpio. The first
+is the external gpio interrupt and second is the external wakeup interrupts.
+The difference between the two is that the external wakeup interrupts can be
+used as system wakeup events.
+
+A. External GPIO Interrupts: For supporting external gpio interrupts, the
+   following properties should be specified in the pin-controller device node.
+
+- interrupt-controller: identifies the controller node as interrupt-parent.
+- #interrupt-cells: the value of this property should be 2.
+  - First Cell: represents the external gpio interrupt number local to the
+    external gpio interrupt space of the controller.
+  - Second Cell: flags to identify the type of the interrupt
+    - 1 = rising edge triggered
+    - 2 = falling edge triggered
+    - 3 = rising and falling edge triggered
+    - 4 = high level triggered
+    - 8 = low level triggered
+
+B. External Wakeup Interrupts: For supporting external wakeup interrupts, a
+   child node representing the external wakeup interrupt controller should be
+   included in the pin-controller device node. This child node should include
+   the following properties.
+
+   - compatible: identifies the type of the external wakeup interrupt controller
+     The possible values are:
+     - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller
+       found on Samsung Exynos4210 SoC.
+   - interrupt-parent: phandle of the interrupt parent to which the external
+     wakeup interrupts are forwarded to.
+   - interrupt-controller: identifies the node as interrupt-parent.
+   - #interrupt-cells: the value of this property should be 2
+     - First Cell: represents the external wakeup interrupt number local to
+       the external wakeup interrupt space of the controller.
+     - Second Cell: flags to identify the type of the interrupt
+       - 1 = rising edge triggered
+       - 2 = falling edge triggered
+       - 3 = rising and falling edge triggered
+       - 4 = high level triggered
+       - 8 = low level triggered
+
+Aliases:
+
+All the pin controller nodes should be represented in the aliases node using
+the following format 'pinctrl{n}' where n is a unique number for the alias.
+
+Example 1: A pin-controller node with pin groups.
+
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+
+		uart0_data: uart0-data {
+			samsung,pins = "gpa0-0", "gpa0-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart0_fctl: uart0-fctl {
+			samsung,pins = "gpa0-2", "gpa0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_data: uart1-data {
+			samsung,pins = "gpa0-4", "gpa0-5";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_fctl: uart1-fctl {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c2_bus: i2c2-bus {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+	};
+
+Example 2: A pin-controller node with external wakeup interrupt controller node.
+
+	pinctrl_1: pinctrl@11000000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11000000 0x1000>;
+		interrupts = <0 46 0>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		wakup_eint: wakeup-interrupt-controller {
+			compatible = "samsung,exynos4210-wakeup-eint";
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+					<0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
+					<0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
+					<0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>,
+					<0 32 0>;
+		};
+	};
+
+Example 3: A uart client node that supports 'default' and 'flow-control' states.
+
+	uart@13800000 {
+		compatible = "samsung,exynos4210-uart";
+		reg = <0x13800000 0x100>;
+		interrupts = <0 52 0>;
+		pinctrl-names = "default", "flow-control;
+		pinctrl-0 = <&uart0_data>;
+		pinctrl-1 = <&uart0_data &uart0_fctl>;
+	};
+
+Example 4: Set up the default pin state for uart controller.
+
+	static int s3c24xx_serial_probe(struct platform_device *pdev) {
+		struct pinctrl *pinctrl;
+		...
+		...
+		pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
+	}

arch/arm/Kconfig

@@ -1768,59 +1768,6 @@ config FORCE_MAX_ZONEORDER
 	  This config option is actually maximum order plus one. For example,
 	  a value of 11 means that the largest free memory block is 2^10 pages.
 
-config LEDS
-	bool "Timer and CPU usage LEDs"
-	depends on ARCH_CDB89712 || ARCH_EBSA110 || \
-		   ARCH_EBSA285 || ARCH_INTEGRATOR || \
-		   ARCH_LUBBOCK || MACH_MAINSTONE || ARCH_NETWINDER || \
-		   ARCH_OMAP || ARCH_P720T || ARCH_PXA_IDP || \
-		   ARCH_SA1100 || ARCH_SHARK || ARCH_VERSATILE || \
-		   ARCH_AT91 || ARCH_DAVINCI || \
-		   ARCH_KS8695 || MACH_RD88F5182 || ARCH_REALVIEW
-	help
-	  If you say Y here, the LEDs on your machine will be used
-	  to provide useful information about your current system status.
-
-	  If you are compiling a kernel for a NetWinder or EBSA-285, you will
-	  be able to select which LEDs are active using the options below. If
-	  you are compiling a kernel for the EBSA-110 or the LART however, the
-	  red LED will simply flash regularly to indicate that the system is
-	  still functional. It is safe to say Y here if you have a CATS
-	  system, but the driver will do nothing.
-
-config LEDS_TIMER
-	bool "Timer LED" if (!ARCH_CDB89712 && !ARCH_OMAP) || \
-			    OMAP_OSK_MISTRAL || MACH_OMAP_H2 \
-			    || MACH_OMAP_PERSEUS2
-	depends on LEDS
-	depends on !GENERIC_CLOCKEVENTS
-	default y if ARCH_EBSA110
-	help
-	  If you say Y here, one of the system LEDs (the green one on the
-	  NetWinder, the amber one on the EBSA285, or the red one on the LART)
-	  will flash regularly to indicate that the system is still
-	  operational. This is mainly useful to kernel hackers who are
-	  debugging unstable kernels.
-
-	  The LART uses the same LED for both Timer LED and CPU usage LED
-	  functions. You may choose to use both, but the Timer LED function
-	  will overrule the CPU usage LED.
-
-config LEDS_CPU
-	bool "CPU usage LED" if (!ARCH_CDB89712 && !ARCH_EBSA110 && \
-			!ARCH_OMAP) \
-			|| OMAP_OSK_MISTRAL || MACH_OMAP_H2 \
-			|| MACH_OMAP_PERSEUS2
-	depends on LEDS
-	help
-	  If you say Y here, the red LED will be used to give a good real
-	  time indication of CPU usage, by lighting whenever the idle task
-	  is not currently executing.
-
-	  The LART uses the same LED for both Timer LED and CPU usage LED
-	  functions. You may choose to use both, but the Timer LED function
-	  will overrule the CPU usage LED.
-
 config ALIGNMENT_TRAP
 	bool
 	depends on CPU_CP15_MMU

arch/arm/boot/dts/exynos4210-pinctrl.dtsi

@@ -0,0 +1,457 @@
+/*
+ * Samsung's Exynos4210 SoC pin-mux and pin-config device tree source
+ *
+ * Copyright (c) 2011-2012 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2011-2012 Linaro Ltd.
+ *		www.linaro.org
+ *
+ * Samsung's Exynos4210 SoC pin-mux and pin-config optiosn are listed as device
+ * tree nodes are listed in this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/ {
+	pinctrl@11400000 {
+		uart0_data: uart0-data {
+			samsung,pins = "gpa0-0", "gpa0-1";
+			samsung,pin-function = <0x2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart0_fctl: uart0-fctl {
+			samsung,pins = "gpa0-2", "gpa0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_data: uart1-data {
+			samsung,pins = "gpa0-4", "gpa0-5";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart1_fctl: uart1-fctl {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c2_bus: i2c2-bus {
+			samsung,pins = "gpa0-6", "gpa0-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart2_data: uart2-data {
+			samsung,pins = "gpa1-0", "gpa1-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart2_fctl: uart2-fctl {
+			samsung,pins = "gpa1-2", "gpa1-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart_audio_a: uart-audio-a {
+			samsung,pins = "gpa1-0", "gpa1-1";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c3_bus: i2c3-bus {
+			samsung,pins = "gpa1-2", "gpa1-3";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart3_data: uart3-data {
+			samsung,pins = "gpa1-4", "gpa1-5";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		uart_audio_b: uart-audio-b {
+			samsung,pins = "gpa1-4", "gpa1-5";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		spi0_bus: spi0-bus {
+			samsung,pins = "gpb-0", "gpb-2", "gpb-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c4_bus: i2c4-bus {
+			samsung,pins = "gpb-2", "gpb-3";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		spi1_bus: spi1-bus {
+			samsung,pins = "gpb-4", "gpb-6", "gpb-7";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c5_bus: i2c5-bus {
+			samsung,pins = "gpb-6", "gpb-7";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2s1_bus: i2s1-bus {
+			samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
+					"gpc0-4";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		pcm1_bus: pcm1-bus {
+			samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
+					"gpc0-4";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		ac97_bus: ac97-bus {
+			samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
+					"gpc0-4";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2s2_bus: i2s2-bus {
+			samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
+					"gpc1-4";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		pcm2_bus: pcm2-bus {
+			samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
+					"gpc1-4";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		spdif_bus: spdif-bus {
+			samsung,pins = "gpc1-0", "gpc1-1";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c6_bus: i2c6-bus {
+			samsung,pins = "gpc1-3", "gpc1-4";
+			samsung,pin-function = <4>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		spi2_bus: spi2-bus {
+			samsung,pins = "gpc1-1", "gpc1-2", "gpc1-3", "gpc1-4";
+			samsung,pin-function = <5>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c7_bus: i2c7-bus {
+			samsung,pins = "gpd0-2", "gpd0-3";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c0_bus: i2c0-bus {
+			samsung,pins = "gpd1-0", "gpd1-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		i2c1_bus: i2c1-bus {
+			samsung,pins = "gpd1-2", "gpd1-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+	};
+
+	pinctrl@11000000 {
+		sd0_clk: sd0-clk {
+			samsung,pins = "gpk0-0";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd0_cmd: sd0-cmd {
+			samsung,pins = "gpk0-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd0_cd: sd0-cd {
+			samsung,pins = "gpk0-2";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd0_bus1: sd0-bus-width1 {
+			samsung,pins = "gpk0-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd0_bus4: sd0-bus-width4 {
+			samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd0_bus8: sd0-bus-width8 {
+			samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd4_clk: sd4-clk {
+			samsung,pins = "gpk0-0";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd4_cmd: sd4-cmd {
+			samsung,pins = "gpk0-1";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd4_cd: sd4-cd {
+			samsung,pins = "gpk0-2";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd4_bus1: sd4-bus-width1 {
+			samsung,pins = "gpk0-3";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd4_bus4: sd4-bus-width4 {
+			samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd4_bus8: sd4-bus-width8 {
+			samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <4>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd1_clk: sd1-clk {
+			samsung,pins = "gpk1-0";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd1_cmd: sd1-cmd {
+			samsung,pins = "gpk1-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd1_cd: sd1-cd {
+			samsung,pins = "gpk1-2";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd1_bus1: sd1-bus-width1 {
+			samsung,pins = "gpk1-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd1_bus4: sd1-bus-width4 {
+			samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd2_clk: sd2-clk {
+			samsung,pins = "gpk2-0";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd2_cmd: sd2-cmd {
+			samsung,pins = "gpk2-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd2_cd: sd2-cd {
+			samsung,pins = "gpk2-2";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd2_bus1: sd2-bus-width1 {
+			samsung,pins = "gpk2-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd2_bus4: sd2-bus-width4 {
+			samsung,pins = "gpk2-3", "gpk2-4", "gpk2-5", "gpk2-6";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd2_bus8: sd2-bus-width8 {
+			samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
+			samsung,pin-function = <3>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd3_clk: sd3-clk {
+			samsung,pins = "gpk3-0";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd3_cmd: sd3-cmd {
+			samsung,pins = "gpk3-1";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd3_cd: sd3-cd {
+			samsung,pins = "gpk3-2";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd3_bus1: sd3-bus-width1 {
+			samsung,pins = "gpk3-3";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		sd3_bus4: sd3-bus-width4 {
+			samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
+			samsung,pin-function = <2>;
+			samsung,pin-pud = <3>;
+			samsung,pin-drv = <0>;
+		};
+
+		eint0: ext-int0 {
+			samsung,pins = "gpx0-0";
+			samsung,pin-function = <0xf>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		eint8: ext-int8 {
+			samsung,pins = "gpx1-0";
+			samsung,pin-function = <0xf>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		eint15: ext-int15 {
+			samsung,pins = "gpx1-7";
+			samsung,pin-function = <0xf>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		eint16: ext-int16 {
+			samsung,pins = "gpx2-0";
+			samsung,pin-function = <0xf>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		eint31: ext-int31 {
+			samsung,pins = "gpx3-7";
+			samsung,pin-function = <0xf>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+	};
+
+	pinctrl@03860000 {
+		i2s0_bus: i2s0-bus {
+			samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
+					"gpz-4", "gpz-5", "gpz-6";
+			samsung,pin-function = <0x2>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+
+		pcm0_bus: pcm0-bus {
+			samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
+					"gpz-4";
+			samsung,pin-function = <0x3>;
+			samsung,pin-pud = <0>;
+			samsung,pin-drv = <0>;
+		};
+	};
+};

arch/arm/boot/dts/exynos4210.dtsi

@@ -20,6 +20,7 @@
 */
 
 /include/ "skeleton.dtsi"
+/include/ "exynos4210-pinctrl.dtsi"
 
 / {
 	compatible = "samsung,exynos4210";
@@ -29,6 +30,9 @@
 		spi0 = &spi_0;
 		spi1 = &spi_1;
 		spi2 = &spi_2;
+		pinctrl0 = &pinctrl_0;
+		pinctrl1 = &pinctrl_1;
+		pinctrl2 = &pinctrl_2;
 	};
 
 	gic:interrupt-controller@10490000 {
@@ -50,6 +54,39 @@
 			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
 	};
 
+	pinctrl_0: pinctrl@11400000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11400000 0x1000>;
+		interrupts = <0 47 0>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	pinctrl_1: pinctrl@11000000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x11000000 0x1000>;
+		interrupts = <0 46 0>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		wakup_eint: wakeup-interrupt-controller {
+			compatible = "samsung,exynos4210-wakeup-eint";
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>,
+					<0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>,
+					<0 24 0>, <0 25 0>, <0 26 0>, <0 27 0>,
+					<0 28 0>, <0 29 0>, <0 30 0>, <0 31 0>,
+					<0 32 0>;
+		};
+	};
+
+	pinctrl_2: pinctrl@03860000 {
+		compatible = "samsung,pinctrl-exynos4210";
+		reg = <0x03860000 0x1000>;
+	};
+
 	watchdog@10060000 {
 		compatible = "samsung,s3c2410-wdt";
 		reg = <0x10060000 0x100>;

arch/arm/boot/dts/exynos5250.dtsi

@@ -27,6 +27,10 @@
 		spi0 = &spi_0;
 		spi1 = &spi_1;
 		spi2 = &spi_2;
+		gsc0 = &gsc_0;
+		gsc1 = &gsc_1;
+		gsc2 = &gsc_2;
+		gsc3 = &gsc_3;
 	};
 
 	gic:interrupt-controller@10481000 {
@@ -460,4 +464,28 @@
 			#gpio-cells = <4>;
 		};
 	};
+
+	gsc_0:  gsc@0x13e00000 {
+		compatible = "samsung,exynos5-gsc";
+		reg = <0x13e00000 0x1000>;
+		interrupts = <0 85 0>;
+	};
+
+	gsc_1:  gsc@0x13e10000 {
+		compatible = "samsung,exynos5-gsc";
+		reg = <0x13e10000 0x1000>;
+		interrupts = <0 86 0>;
+	};
+
+	gsc_2:  gsc@0x13e20000 {
+		compatible = "samsung,exynos5-gsc";
+		reg = <0x13e20000 0x1000>;
+		interrupts = <0 87 0>;
+	};
+
+	gsc_3:  gsc@0x13e30000 {
+		compatible = "samsung,exynos5-gsc";
+		reg = <0x13e30000 0x1000>;
+		interrupts = <0 88 0>;
+	};
 };

arch/arm/boot/dts/omap4.dtsi

@@ -430,5 +430,13 @@
 			hw-caps-ll-interface;
 			hw-caps-temp-alert;
 		};
+
+		ocp2scp {
+			compatible = "ti,omap-ocp2scp";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			ti,hwmods = "ocp2scp_usb_phy";
+		};
 	};
 };

arch/arm/configs/afeb9260_defconfig

@@ -39,7 +39,6 @@ CONFIG_MTD_BLOCK=y
 CONFIG_MTD_DATAFLASH=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_ATMEL=y
-CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=8192
 CONFIG_ATMEL_SSC=y

arch/arm/configs/at91rm9200_defconfig

@@ -232,7 +232,7 @@ CONFIG_USB_GADGET=y
 CONFIG_USB_ETH=m
 CONFIG_USB_MASS_STORAGE=m
 CONFIG_MMC=y
-CONFIG_MMC_AT91=y
+CONFIG_MMC_ATMELMCI=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_GPIO=y

arch/arm/configs/at91sam9261_defconfig

@@ -128,7 +128,7 @@ CONFIG_USB_GADGETFS=m
 CONFIG_USB_FILE_STORAGE=m
 CONFIG_USB_G_SERIAL=m
 CONFIG_MMC=y
-CONFIG_MMC_AT91=m
+CONFIG_MMC_ATMELMCI=m
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_GPIO=y

arch/arm/configs/at91sam9263_defconfig

@@ -61,7 +61,6 @@ CONFIG_MTD_DATAFLASH=y
 CONFIG_MTD_BLOCK2MTD=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_ATMEL=y
-CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
 CONFIG_MTD_UBI=y
 CONFIG_MTD_UBI_GLUEBI=y
 CONFIG_BLK_DEV_LOOP=y
@@ -138,7 +137,7 @@ CONFIG_USB_FILE_STORAGE=m
 CONFIG_USB_G_SERIAL=m
 CONFIG_MMC=y
 CONFIG_SDIO_UART=m
-CONFIG_MMC_AT91=m
+CONFIG_MMC_ATMELMCI=m
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_ATMEL_PWM=y

arch/arm/configs/at91sam9g20_defconfig

@@ -99,7 +99,7 @@ CONFIG_USB_GADGETFS=m
 CONFIG_USB_FILE_STORAGE=m
 CONFIG_USB_G_SERIAL=m
 CONFIG_MMC=y
-CONFIG_MMC_AT91=m
+CONFIG_MMC_ATMELMCI=m
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_GPIO=y

arch/arm/configs/at91sam9rl_defconfig

@@ -60,7 +60,7 @@ CONFIG_AT91SAM9X_WATCHDOG=y
 CONFIG_FB=y
 CONFIG_FB_ATMEL=y
 CONFIG_MMC=y
-CONFIG_MMC_AT91=m
+CONFIG_MMC_ATMELMCI=m
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_AT91SAM9=y
 CONFIG_EXT2_FS=y

arch/arm/configs/cpu9260_defconfig

@@ -82,7 +82,7 @@ CONFIG_USB_STORAGE=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_ETH=m
 CONFIG_MMC=y
-CONFIG_MMC_AT91=m
+CONFIG_MMC_ATMELMCI=m
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_GPIO=y

arch/arm/configs/cpu9g20_defconfig

@@ -82,7 +82,7 @@ CONFIG_USB_STORAGE=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_ETH=m
 CONFIG_MMC=y
-CONFIG_MMC_AT91=m
+CONFIG_MMC_ATMELMCI=m
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_GPIO=y

arch/arm/configs/qil-a9260_defconfig

@@ -50,7 +50,6 @@ CONFIG_MTD_BLOCK=y
 CONFIG_MTD_DATAFLASH=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_ATMEL=y
-CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
 CONFIG_BLK_DEV_LOOP=y
 # CONFIG_MISC_DEVICES is not set
 CONFIG_SCSI=y
@@ -87,7 +86,7 @@ CONFIG_USB_STORAGE=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_ETH=m
 CONFIG_MMC=y
-CONFIG_MMC_AT91=m
+CONFIG_MMC_ATMELMCI=m
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_GPIO=y

arch/arm/configs/stamp9g20_defconfig

@@ -100,7 +100,6 @@ CONFIG_USB_ETH=m
 CONFIG_USB_FILE_STORAGE=m
 CONFIG_USB_G_SERIAL=m
 CONFIG_MMC=y
-# CONFIG_MMC_AT91 is not set
 CONFIG_MMC_ATMELMCI=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y

arch/arm/configs/usb-a9260_defconfig

@@ -49,7 +49,6 @@ CONFIG_MTD_BLOCK=y
 CONFIG_MTD_DATAFLASH=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_ATMEL=y
-CONFIG_MTD_NAND_ATMEL_ECC_SOFT=y
 CONFIG_BLK_DEV_LOOP=y
 # CONFIG_MISC_DEVICES is not set
 CONFIG_SCSI=y

arch/arm/include/asm/leds.h

@@ -1,50 +0,0 @@
-/*
- *  arch/arm/include/asm/leds.h
- *
- *  Copyright (C) 1998 Russell King
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- *  Event-driven interface for LEDs on machines
- *  Added led_start and led_stop- Alex Holden, 28th Dec 1998.
- */
-#ifndef ASM_ARM_LEDS_H
-#define ASM_ARM_LEDS_H
-
-
-typedef enum {
-	led_idle_start,
-	led_idle_end,
-	led_timer,
-	led_start,
-	led_stop,
-	led_claim,		/* override idle & timer leds */
-	led_release,		/* restore idle & timer leds */
-	led_start_timer_mode,
-	led_stop_timer_mode,
-	led_green_on,
-	led_green_off,
-	led_amber_on,
-	led_amber_off,
-	led_red_on,
-	led_red_off,
-	led_blue_on,
-	led_blue_off,
-	/*
-	 * I want this between led_timer and led_start, but
-	 * someone has decided to export this to user space
-	 */
-	led_halted
-} led_event_t;
-
-/* Use this routine to handle LEDs */
-
-#ifdef CONFIG_LEDS
-extern void (*leds_event)(led_event_t);
-#else
-#define leds_event(e)
-#endif
-
-#endif

arch/arm/kernel/Makefile

@@ -21,7 +21,6 @@ obj-y		:= elf.o entry-armv.o entry-common.o irq.o opcodes.o \
 
 obj-$(CONFIG_DEPRECATED_PARAM_STRUCT) += compat.o
 
-obj-$(CONFIG_LEDS)		+= leds.o
 obj-$(CONFIG_OC_ETM)		+= etm.o
 obj-$(CONFIG_CPU_IDLE)		+= cpuidle.o
 obj-$(CONFIG_ISA_DMA_API)	+= dma.o

arch/arm/kernel/leds.c

@@ -1,121 +0,0 @@
-/*
- * LED support code, ripped out of arch/arm/kernel/time.c
- *
- *  Copyright (C) 1994-2001 Russell King
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/export.h>
-#include <linux/init.h>
-#include <linux/device.h>
-#include <linux/syscore_ops.h>
-#include <linux/string.h>
-
-#include <asm/leds.h>
-
-static void dummy_leds_event(led_event_t evt)
-{
-}
-
-void (*leds_event)(led_event_t) = dummy_leds_event;
-
-struct leds_evt_name {
-	const char	name[8];
-	int		on;
-	int		off;
-};
-
-static const struct leds_evt_name evt_names[] = {
-	{ "amber", led_amber_on, led_amber_off },
-	{ "blue",  led_blue_on,  led_blue_off  },
-	{ "green", led_green_on, led_green_off },
-	{ "red",   led_red_on,   led_red_off   },
-};
-
-static ssize_t leds_store(struct device *dev,
-			struct device_attribute *attr,
-			const char *buf, size_t size)
-{
-	int ret = -EINVAL, len = strcspn(buf, " ");
-
-	if (len > 0 && buf[len] == '\0')
-		len--;
-
-	if (strncmp(buf, "claim", len) == 0) {
-		leds_event(led_claim);
-		ret = size;
-	} else if (strncmp(buf, "release", len) == 0) {
-		leds_event(led_release);
-		ret = size;
-	} else {
-		int i;
-
-		for (i = 0; i < ARRAY_SIZE(evt_names); i++) {
-			if (strlen(evt_names[i].name) != len ||
-			    strncmp(buf, evt_names[i].name, len) != 0)
-				continue;
-			if (strncmp(buf+len, " on", 3) == 0) {
-				leds_event(evt_names[i].on);
-				ret = size;
-			} else if (strncmp(buf+len, " off", 4) == 0) {
-				leds_event(evt_names[i].off);
-				ret = size;
-			}
-			break;
-		}
-	}
-	return ret;
-}
-
-static DEVICE_ATTR(event, 0200, NULL, leds_store);
-
-static struct bus_type leds_subsys = {
-	.name		= "leds",
-	.dev_name	= "leds",
-};
-
-static struct device leds_device = {
-	.id		= 0,
-	.bus		= &leds_subsys,
-};
-
-static int leds_suspend(void)
-{
-	leds_event(led_stop);
-	return 0;
-}
-
-static void leds_resume(void)
-{
-	leds_event(led_start);
-}
-
-static void leds_shutdown(void)
-{
-	leds_event(led_halted);
-}
-
-static struct syscore_ops leds_syscore_ops = {
-	.shutdown	= leds_shutdown,
-	.suspend	= leds_suspend,
-	.resume		= leds_resume,
-};
-
-static int __init leds_init(void)
-{
-	int ret;
-	ret = subsys_system_register(&leds_subsys, NULL);
-	if (ret == 0)
-		ret = device_register(&leds_device);
-	if (ret == 0)
-		ret = device_create_file(&leds_device, &dev_attr_event);
-	if (ret == 0)
-		register_syscore_ops(&leds_syscore_ops);
-	return ret;
-}
-
-device_initcall(leds_init);
-
-EXPORT_SYMBOL(leds_event);

arch/arm/kernel/process.c

@@ -31,9 +31,9 @@
 #include <linux/random.h>
 #include <linux/hw_breakpoint.h>
 #include <linux/cpuidle.h>
+#include <linux/leds.h>
 
 #include <asm/cacheflush.h>
-#include <asm/leds.h>
 #include <asm/processor.h>
 #include <asm/thread_notify.h>
 #include <asm/stacktrace.h>
@@ -189,7 +189,7 @@ void cpu_idle(void)
 	while (1) {
 		tick_nohz_idle_enter();
 		rcu_idle_enter();
-		leds_event(led_idle_start);
+		ledtrig_cpu(CPU_LED_IDLE_START);
 		while (!need_resched()) {
 #ifdef CONFIG_HOTPLUG_CPU
 			if (cpu_is_offline(smp_processor_id()))
@@ -220,7 +220,7 @@ void cpu_idle(void)
 			} else
 				local_irq_enable();
 		}
-		leds_event(led_idle_end);
+		ledtrig_cpu(CPU_LED_IDLE_END);
 		rcu_idle_exit();
 		tick_nohz_idle_exit();
 		schedule_preempt_disabled();

arch/arm/kernel/time.c

@@ -25,7 +25,6 @@
 #include <linux/timer.h>
 #include <linux/irq.h>
 
-#include <asm/leds.h>
 #include <asm/thread_info.h>
 #include <asm/sched_clock.h>
 #include <asm/stacktrace.h>
@@ -80,21 +79,6 @@ u32 arch_gettimeoffset(void)
 }
 #endif /* CONFIG_ARCH_USES_GETTIMEOFFSET */
 
-#ifdef CONFIG_LEDS_TIMER
-static inline void do_leds(void)
-{
-	static unsigned int count = HZ/2;
-
-	if (--count == 0) {
-		count = HZ/2;
-		leds_event(led_timer);
-	}
-}
-#else
-#define	do_leds()
-#endif
-
-
 #ifndef CONFIG_GENERIC_CLOCKEVENTS
 /*
  * Kernel system timer support.
@@ -102,7 +86,6 @@ static inline void do_leds(void)
 void timer_tick(void)
 {
 	profile_tick(CPU_PROFILING);
-	do_leds();
 	xtime_update(1);
 #ifndef CONFIG_SMP
 	update_process_times(user_mode(get_irq_regs()));

arch/arm/mach-at91/at91rm9200_devices.c

@@ -294,9 +294,9 @@ void __init at91_add_device_cf(struct at91_cf_data *data) {}
  *  MMC / SD
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
+#if IS_ENABLED(CONFIG_MMC_ATMELMCI)
 static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct at91_mmc_data mmc_data;
+static struct mci_platform_data mmc_data;
 
 static struct resource mmc_resources[] = {
 	[0] = {
@@ -312,7 +312,7 @@ static struct resource mmc_resources[] = {
 };
 
 static struct platform_device at91rm9200_mmc_device = {
-	.name		= "at91_mci",
+	.name		= "atmel_mci",
 	.id		= -1,
 	.dev		= {
 				.dma_mask		= &mmc_dmamask,
@@ -323,53 +323,69 @@ static struct platform_device at91rm9200_mmc_device = {
 	.num_resources	= ARRAY_SIZE(mmc_resources),
 };
 
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
+void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 {
+	unsigned int i;
+	unsigned int slot_count = 0;
+
 	if (!data)
 		return;
 
-	/* input/irq */
-	if (gpio_is_valid(data->det_pin)) {
-		at91_set_gpio_input(data->det_pin, 1);
-		at91_set_deglitch(data->det_pin, 1);
-	}
-	if (gpio_is_valid(data->wp_pin))
-		at91_set_gpio_input(data->wp_pin, 1);
-	if (gpio_is_valid(data->vcc_pin))
-		at91_set_gpio_output(data->vcc_pin, 0);
-
-	/* CLK */
-	at91_set_A_periph(AT91_PIN_PA27, 0);
+	for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
 
-	if (data->slot_b) {
-		/* CMD */
-		at91_set_B_periph(AT91_PIN_PA8, 1);
+		if (!data->slot[i].bus_width)
+			continue;
 
-		/* DAT0, maybe DAT1..DAT3 */
-		at91_set_B_periph(AT91_PIN_PA9, 1);
-		if (data->wire4) {
-			at91_set_B_periph(AT91_PIN_PA10, 1);
-			at91_set_B_periph(AT91_PIN_PA11, 1);
-			at91_set_B_periph(AT91_PIN_PA12, 1);
+		/* input/irq */
+		if (gpio_is_valid(data->slot[i].detect_pin)) {
+			at91_set_gpio_input(data->slot[i].detect_pin, 1);
+			at91_set_deglitch(data->slot[i].detect_pin, 1);
 		}
-	} else {
-		/* CMD */
-		at91_set_A_periph(AT91_PIN_PA28, 1);
-
-		/* DAT0, maybe DAT1..DAT3 */
-		at91_set_A_periph(AT91_PIN_PA29, 1);
-		if (data->wire4) {
-			at91_set_B_periph(AT91_PIN_PB3, 1);
-			at91_set_B_periph(AT91_PIN_PB4, 1);
-			at91_set_B_periph(AT91_PIN_PB5, 1);
+		if (gpio_is_valid(data->slot[i].wp_pin))
+			at91_set_gpio_input(data->slot[i].wp_pin, 1);
+
+		switch (i) {
+		case 0:					/* slot A */
+			/* CMD */
+			at91_set_A_periph(AT91_PIN_PA28, 1);
+			/* DAT0, maybe DAT1..DAT3 */
+			at91_set_A_periph(AT91_PIN_PA29, 1);
+			if (data->slot[i].bus_width == 4) {
+				at91_set_B_periph(AT91_PIN_PB3, 1);
+				at91_set_B_periph(AT91_PIN_PB4, 1);
+				at91_set_B_periph(AT91_PIN_PB5, 1);
+			}
+			slot_count++;
+			break;
+		case 1:					/* slot B */
+			/* CMD */
+			at91_set_B_periph(AT91_PIN_PA8, 1);
+			/* DAT0, maybe DAT1..DAT3 */
+			at91_set_B_periph(AT91_PIN_PA9, 1);
+			if (data->slot[i].bus_width == 4) {
+				at91_set_B_periph(AT91_PIN_PA10, 1);
+				at91_set_B_periph(AT91_PIN_PA11, 1);
+				at91_set_B_periph(AT91_PIN_PA12, 1);
+			}
+			slot_count++;
+			break;
+		default:
+			printk(KERN_ERR
+			       "AT91: SD/MMC slot %d not available\n", i);
+			break;
+		}
+		if (slot_count) {
+			/* CLK */
+			at91_set_A_periph(AT91_PIN_PA27, 0);
+
+			mmc_data = *data;
+			platform_device_register(&at91rm9200_mmc_device);
 		}
 	}
 
-	mmc_data = *data;
-	platform_device_register(&at91rm9200_mmc_device);
 }
 #else
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
+void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {}
 #endif
 
 

arch/arm/mach-at91/at91sam9260_devices.c

@@ -208,93 +208,11 @@ void __init at91_add_device_eth(struct macb_platform_data *data) {}
 #endif
 
 
-/* --------------------------------------------------------------------
- *  MMC / SD
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
-static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct at91_mmc_data mmc_data;
-
-static struct resource mmc_resources[] = {
-	[0] = {
-		.start	= AT91SAM9260_BASE_MCI,
-		.end	= AT91SAM9260_BASE_MCI + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= NR_IRQS_LEGACY + AT91SAM9260_ID_MCI,
-		.end	= NR_IRQS_LEGACY + AT91SAM9260_ID_MCI,
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device at91sam9260_mmc_device = {
-	.name		= "at91_mci",
-	.id		= -1,
-	.dev		= {
-				.dma_mask		= &mmc_dmamask,
-				.coherent_dma_mask	= DMA_BIT_MASK(32),
-				.platform_data		= &mmc_data,
-	},
-	.resource	= mmc_resources,
-	.num_resources	= ARRAY_SIZE(mmc_resources),
-};
-
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
-{
-	if (!data)
-		return;
-
-	/* input/irq */
-	if (gpio_is_valid(data->det_pin)) {
-		at91_set_gpio_input(data->det_pin, 1);
-		at91_set_deglitch(data->det_pin, 1);
-	}
-	if (gpio_is_valid(data->wp_pin))
-		at91_set_gpio_input(data->wp_pin, 1);
-	if (gpio_is_valid(data->vcc_pin))
-		at91_set_gpio_output(data->vcc_pin, 0);
-
-	/* CLK */
-	at91_set_A_periph(AT91_PIN_PA8, 0);
-
-	if (data->slot_b) {
-		/* CMD */
-		at91_set_B_periph(AT91_PIN_PA1, 1);
-
-		/* DAT0, maybe DAT1..DAT3 */
-		at91_set_B_periph(AT91_PIN_PA0, 1);
-		if (data->wire4) {
-			at91_set_B_periph(AT91_PIN_PA5, 1);
-			at91_set_B_periph(AT91_PIN_PA4, 1);
-			at91_set_B_periph(AT91_PIN_PA3, 1);
-		}
-	} else {
-		/* CMD */
-		at91_set_A_periph(AT91_PIN_PA7, 1);
-
-		/* DAT0, maybe DAT1..DAT3 */
-		at91_set_A_periph(AT91_PIN_PA6, 1);
-		if (data->wire4) {
-			at91_set_A_periph(AT91_PIN_PA9, 1);
-			at91_set_A_periph(AT91_PIN_PA10, 1);
-			at91_set_A_periph(AT91_PIN_PA11, 1);
-		}
-	}
-
-	mmc_data = *data;
-	platform_device_register(&at91sam9260_mmc_device);
-}
-#else
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
-#endif
-
 /* --------------------------------------------------------------------
  *  MMC / SD Slot for Atmel MCI Driver
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
+#if IS_ENABLED(CONFIG_MMC_ATMELMCI)
 static u64 mmc_dmamask = DMA_BIT_MASK(32);
 static struct mci_platform_data mmc_data;
 

arch/arm/mach-at91/at91sam9261_devices.c

@@ -137,9 +137,9 @@ void __init at91_add_device_udc(struct at91_udc_data *data) {}
  *  MMC / SD
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
+#if IS_ENABLED(CONFIG_MMC_ATMELMCI)
 static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct at91_mmc_data mmc_data;
+static struct mci_platform_data mmc_data;
 
 static struct resource mmc_resources[] = {
 	[0] = {
@@ -155,7 +155,7 @@ static struct resource mmc_resources[] = {
 };
 
 static struct platform_device at91sam9261_mmc_device = {
-	.name		= "at91_mci",
+	.name		= "atmel_mci",
 	.id		= -1,
 	.dev		= {
 				.dma_mask		= &mmc_dmamask,
@@ -166,40 +166,40 @@ static struct platform_device at91sam9261_mmc_device = {
 	.num_resources	= ARRAY_SIZE(mmc_resources),
 };
 
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
+void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 {
 	if (!data)
 		return;
 
-	/* input/irq */
-	if (gpio_is_valid(data->det_pin)) {
-		at91_set_gpio_input(data->det_pin, 1);
-		at91_set_deglitch(data->det_pin, 1);
-	}
-	if (gpio_is_valid(data->wp_pin))
-		at91_set_gpio_input(data->wp_pin, 1);
-	if (gpio_is_valid(data->vcc_pin))
-		at91_set_gpio_output(data->vcc_pin, 0);
-
-	/* CLK */
-	at91_set_B_periph(AT91_PIN_PA2, 0);
-
-	/* CMD */
-	at91_set_B_periph(AT91_PIN_PA1, 1);
-
-	/* DAT0, maybe DAT1..DAT3 */
-	at91_set_B_periph(AT91_PIN_PA0, 1);
-	if (data->wire4) {
-		at91_set_B_periph(AT91_PIN_PA4, 1);
-		at91_set_B_periph(AT91_PIN_PA5, 1);
-		at91_set_B_periph(AT91_PIN_PA6, 1);
-	}
+	if (data->slot[0].bus_width) {
+		/* input/irq */
+		if (gpio_is_valid(data->slot[0].detect_pin)) {
+			at91_set_gpio_input(data->slot[0].detect_pin, 1);
+			at91_set_deglitch(data->slot[0].detect_pin, 1);
+		}
+		if (gpio_is_valid(data->slot[0].wp_pin))
+			at91_set_gpio_input(data->slot[0].wp_pin, 1);
+
+		/* CLK */
+		at91_set_B_periph(AT91_PIN_PA2, 0);
 
-	mmc_data = *data;
-	platform_device_register(&at91sam9261_mmc_device);
+		/* CMD */
+		at91_set_B_periph(AT91_PIN_PA1, 1);
+
+		/* DAT0, maybe DAT1..DAT3 */
+		at91_set_B_periph(AT91_PIN_PA0, 1);
+		if (data->slot[0].bus_width == 4) {
+			at91_set_B_periph(AT91_PIN_PA4, 1);
+			at91_set_B_periph(AT91_PIN_PA5, 1);
+			at91_set_B_periph(AT91_PIN_PA6, 1);
+		}
+
+		mmc_data = *data;
+		platform_device_register(&at91sam9261_mmc_device);
+	}
 }
 #else
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
+void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {}
 #endif
 
 

arch/arm/mach-at91/at91sam9263.c

@@ -188,8 +188,8 @@ static struct clk_lookup periph_clocks_lookups[] = {
 	CLKDEV_CON_ID("hclk", &macb_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.0", &ssc0_clk),
 	CLKDEV_CON_DEV_ID("pclk", "ssc.1", &ssc1_clk),
-	CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.0", &mmc0_clk),
-	CLKDEV_CON_DEV_ID("mci_clk", "at91_mci.1", &mmc1_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.0", &mmc0_clk),
+	CLKDEV_CON_DEV_ID("mci_clk", "atmel_mci.1", &mmc1_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.0", &spi0_clk),
 	CLKDEV_CON_DEV_ID("spi_clk", "atmel_spi.1", &spi1_clk),
 	CLKDEV_CON_DEV_ID("t0_clk", "atmel_tcb.0", &tcb_clk),

arch/arm/mach-at91/at91sam9263_devices.c

@@ -218,9 +218,9 @@ void __init at91_add_device_eth(struct macb_platform_data *data) {}
  *  MMC / SD
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
+#if IS_ENABLED(CONFIG_MMC_ATMELMCI)
 static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct at91_mmc_data mmc0_data, mmc1_data;
+static struct mci_platform_data mmc0_data, mmc1_data;
 
 static struct resource mmc0_resources[] = {
 	[0] = {
@@ -236,7 +236,7 @@ static struct resource mmc0_resources[] = {
 };
 
 static struct platform_device at91sam9263_mmc0_device = {
-	.name		= "at91_mci",
+	.name		= "atmel_mci",
 	.id		= 0,
 	.dev		= {
 				.dma_mask		= &mmc_dmamask,
@@ -261,7 +261,7 @@ static struct resource mmc1_resources[] = {
 };
 
 static struct platform_device at91sam9263_mmc1_device = {
-	.name		= "at91_mci",
+	.name		= "atmel_mci",
 	.id		= 1,
 	.dev		= {
 				.dma_mask		= &mmc_dmamask,
@@ -272,85 +272,110 @@ static struct platform_device at91sam9263_mmc1_device = {
 	.num_resources	= ARRAY_SIZE(mmc1_resources),
 };
 
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
+void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 {
+	unsigned int i;
+	unsigned int slot_count = 0;
+
 	if (!data)
 		return;
 
-	/* input/irq */
-	if (gpio_is_valid(data->det_pin)) {
-		at91_set_gpio_input(data->det_pin, 1);
-		at91_set_deglitch(data->det_pin, 1);
-	}
-	if (gpio_is_valid(data->wp_pin))
-		at91_set_gpio_input(data->wp_pin, 1);
-	if (gpio_is_valid(data->vcc_pin))
-		at91_set_gpio_output(data->vcc_pin, 0);
+	for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
 
-	if (mmc_id == 0) {		/* MCI0 */
-		/* CLK */
-		at91_set_A_periph(AT91_PIN_PA12, 0);
+		if (!data->slot[i].bus_width)
+			continue;
 
-		if (data->slot_b) {
-			/* CMD */
-			at91_set_A_periph(AT91_PIN_PA16, 1);
+		/* input/irq */
+		if (gpio_is_valid(data->slot[i].detect_pin)) {
+			at91_set_gpio_input(data->slot[i].detect_pin,
+					1);
+			at91_set_deglitch(data->slot[i].detect_pin,
+					1);
+		}
+		if (gpio_is_valid(data->slot[i].wp_pin))
+			at91_set_gpio_input(data->slot[i].wp_pin, 1);
+
+		if (mmc_id == 0) {				/* MCI0 */
+			switch (i) {
+			case 0:					/* slot A */
+				/* CMD */
+				at91_set_A_periph(AT91_PIN_PA1, 1);
+				/* DAT0, maybe DAT1..DAT3 */
+				at91_set_A_periph(AT91_PIN_PA0, 1);
+				if (data->slot[i].bus_width == 4) {
+					at91_set_A_periph(AT91_PIN_PA3, 1);
+					at91_set_A_periph(AT91_PIN_PA4, 1);
+					at91_set_A_periph(AT91_PIN_PA5, 1);
+				}
+				slot_count++;
+				break;
+			case 1:					/* slot B */
+				/* CMD */
+				at91_set_A_periph(AT91_PIN_PA16, 1);
+				/* DAT0, maybe DAT1..DAT3 */
+				at91_set_A_periph(AT91_PIN_PA17, 1);
+				if (data->slot[i].bus_width == 4) {
+					at91_set_A_periph(AT91_PIN_PA18, 1);
+					at91_set_A_periph(AT91_PIN_PA19, 1);
+					at91_set_A_periph(AT91_PIN_PA20, 1);
+				}
+				slot_count++;
+				break;
+			default:
+				printk(KERN_ERR
+				       "AT91: SD/MMC slot %d not available\n", i);
+				break;
+			}
+			if (slot_count) {
+				/* CLK */
+				at91_set_A_periph(AT91_PIN_PA12, 0);
 
-			/* DAT0, maybe DAT1..DAT3 */
-			at91_set_A_periph(AT91_PIN_PA17, 1);
-			if (data->wire4) {
-				at91_set_A_periph(AT91_PIN_PA18, 1);
-				at91_set_A_periph(AT91_PIN_PA19, 1);
-				at91_set_A_periph(AT91_PIN_PA20, 1);
+				mmc0_data = *data;
+				platform_device_register(&at91sam9263_mmc0_device);
 			}
-		} else {
-			/* CMD */
-			at91_set_A_periph(AT91_PIN_PA1, 1);
-
-			/* DAT0, maybe DAT1..DAT3 */
-			at91_set_A_periph(AT91_PIN_PA0, 1);
-			if (data->wire4) {
-				at91_set_A_periph(AT91_PIN_PA3, 1);
-				at91_set_A_periph(AT91_PIN_PA4, 1);
-				at91_set_A_periph(AT91_PIN_PA5, 1);
+		} else if (mmc_id == 1) {			/* MCI1 */
+			switch (i) {
+			case 0:					/* slot A */
+				/* CMD */
+				at91_set_A_periph(AT91_PIN_PA7, 1);
+				/* DAT0, maybe DAT1..DAT3 */
+				at91_set_A_periph(AT91_PIN_PA8, 1);
+				if (data->slot[i].bus_width == 4) {
+					at91_set_A_periph(AT91_PIN_PA9, 1);
+					at91_set_A_periph(AT91_PIN_PA10, 1);
+					at91_set_A_periph(AT91_PIN_PA11, 1);
+				}
+				slot_count++;
+				break;
+			case 1:					/* slot B */
+				/* CMD */
+				at91_set_A_periph(AT91_PIN_PA21, 1);
+				/* DAT0, maybe DAT1..DAT3 */
+				at91_set_A_periph(AT91_PIN_PA22, 1);
+				if (data->slot[i].bus_width == 4) {
+					at91_set_A_periph(AT91_PIN_PA23, 1);
+					at91_set_A_periph(AT91_PIN_PA24, 1);
+					at91_set_A_periph(AT91_PIN_PA25, 1);
+				}
+				slot_count++;
+				break;
+			default:
+				printk(KERN_ERR
+				       "AT91: SD/MMC slot %d not available\n", i);
+				break;
 			}
-		}
+			if (slot_count) {
+				/* CLK */
+				at91_set_A_periph(AT91_PIN_PA6, 0);
 
-		mmc0_data = *data;
-		platform_device_register(&at91sam9263_mmc0_device);
-	} else {			/* MCI1 */
-		/* CLK */
-		at91_set_A_periph(AT91_PIN_PA6, 0);
-
-		if (data->slot_b) {
-			/* CMD */
-			at91_set_A_periph(AT91_PIN_PA21, 1);
-
-			/* DAT0, maybe DAT1..DAT3 */
-			at91_set_A_periph(AT91_PIN_PA22, 1);
-			if (data->wire4) {
-				at91_set_A_periph(AT91_PIN_PA23, 1);
-				at91_set_A_periph(AT91_PIN_PA24, 1);
-				at91_set_A_periph(AT91_PIN_PA25, 1);
-			}
-		} else {
-			/* CMD */
-			at91_set_A_periph(AT91_PIN_PA7, 1);
-
-			/* DAT0, maybe DAT1..DAT3 */
-			at91_set_A_periph(AT91_PIN_PA8, 1);
-			if (data->wire4) {
-				at91_set_A_periph(AT91_PIN_PA9, 1);
-				at91_set_A_periph(AT91_PIN_PA10, 1);
-				at91_set_A_periph(AT91_PIN_PA11, 1);
+				mmc1_data = *data;
+				platform_device_register(&at91sam9263_mmc1_device);
 			}
 		}
-
-		mmc1_data = *data;
-		platform_device_register(&at91sam9263_mmc1_device);
 	}
 }
 #else
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
+void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {}
 #endif
 
 /* --------------------------------------------------------------------

arch/arm/mach-at91/at91sam9rl_devices.c

@@ -161,9 +161,9 @@ void __init at91_add_device_usba(struct usba_platform_data *data) {}
  *  MMC / SD
  * -------------------------------------------------------------------- */
 
-#if defined(CONFIG_MMC_AT91) || defined(CONFIG_MMC_AT91_MODULE)
+#if IS_ENABLED(CONFIG_MMC_ATMELMCI)
 static u64 mmc_dmamask = DMA_BIT_MASK(32);
-static struct at91_mmc_data mmc_data;
+static struct mci_platform_data mmc_data;
 
 static struct resource mmc_resources[] = {
 	[0] = {
@@ -179,7 +179,7 @@ static struct resource mmc_resources[] = {
 };
 
 static struct platform_device at91sam9rl_mmc_device = {
-	.name		= "at91_mci",
+	.name		= "atmel_mci",
 	.id		= -1,
 	.dev		= {
 				.dma_mask		= &mmc_dmamask,
@@ -190,40 +190,40 @@ static struct platform_device at91sam9rl_mmc_device = {
 	.num_resources	= ARRAY_SIZE(mmc_resources),
 };
 
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data)
+void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 {
 	if (!data)
 		return;
 
-	/* input/irq */
-	if (gpio_is_valid(data->det_pin)) {
-		at91_set_gpio_input(data->det_pin, 1);
-		at91_set_deglitch(data->det_pin, 1);
-	}
-	if (gpio_is_valid(data->wp_pin))
-		at91_set_gpio_input(data->wp_pin, 1);
-	if (gpio_is_valid(data->vcc_pin))
-		at91_set_gpio_output(data->vcc_pin, 0);
-
-	/* CLK */
-	at91_set_A_periph(AT91_PIN_PA2, 0);
-
-	/* CMD */
-	at91_set_A_periph(AT91_PIN_PA1, 1);
-
-	/* DAT0, maybe DAT1..DAT3 */
-	at91_set_A_periph(AT91_PIN_PA0, 1);
-	if (data->wire4) {
-		at91_set_A_periph(AT91_PIN_PA3, 1);
-		at91_set_A_periph(AT91_PIN_PA4, 1);
-		at91_set_A_periph(AT91_PIN_PA5, 1);
+	if (data->slot[0].bus_width) {
+		/* input/irq */
+		if (gpio_is_valid(data->slot[0].detect_pin)) {
+			at91_set_gpio_input(data->slot[0].detect_pin, 1);
+			at91_set_deglitch(data->slot[0].detect_pin, 1);
+		}
+		if (gpio_is_valid(data->slot[0].wp_pin))
+			at91_set_gpio_input(data->slot[0].wp_pin, 1);
+
+		/* CLK */
+		at91_set_A_periph(AT91_PIN_PA2, 0);
+
+		/* CMD */
+		at91_set_A_periph(AT91_PIN_PA1, 1);
+
+		/* DAT0, maybe DAT1..DAT3 */
+		at91_set_A_periph(AT91_PIN_PA0, 1);
+		if (data->slot[0].bus_width == 4) {
+			at91_set_A_periph(AT91_PIN_PA3, 1);
+			at91_set_A_periph(AT91_PIN_PA4, 1);
+			at91_set_A_periph(AT91_PIN_PA5, 1);
+		}
+
+		mmc_data = *data;
+		platform_device_register(&at91sam9rl_mmc_device);
 	}
-
-	mmc_data = *data;
-	platform_device_register(&at91sam9rl_mmc_device);
 }
 #else
-void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data) {}
+void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {}
 #endif
 
 

arch/arm/mach-at91/board-afeb-9260v1.c

@@ -133,12 +133,12 @@ static struct atmel_nand_data __initdata afeb9260_nand_data = {
 /*
  * MCI (SD/MMC)
  */
-static struct at91_mmc_data __initdata afeb9260_mmc_data = {
-	.det_pin 	= AT91_PIN_PC9,
-	.wp_pin 	= AT91_PIN_PC4,
-	.slot_b		= 1,
-	.wire4		= 1,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata afeb9260_mci0_data = {
+	.slot[1] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PC9,
+		.wp_pin		= AT91_PIN_PC4,
+	},
 };
 
 
@@ -199,7 +199,7 @@ static void __init afeb9260_board_init(void)
 	at91_set_B_periph(AT91_PIN_PA10, 0);	/* ETX2 */
 	at91_set_B_periph(AT91_PIN_PA11, 0);	/* ETX3 */
 	/* MMC */
-	at91_add_device_mmc(0, &afeb9260_mmc_data);
+	at91_add_device_mci(0, &afeb9260_mci0_data);
 	/* I2C */
 	at91_add_device_i2c(afeb9260_i2c_devices,
 			ARRAY_SIZE(afeb9260_i2c_devices));

arch/arm/mach-at91/board-carmeva.c

@@ -71,12 +71,12 @@ static struct at91_udc_data __initdata carmeva_udc_data = {
 	// .vcc_pin	= -EINVAL,
 // };
 
-static struct at91_mmc_data __initdata carmeva_mmc_data = {
-	.slot_b		= 0,
-	.wire4		= 1,
-	.det_pin	= AT91_PIN_PB10,
-	.wp_pin		= AT91_PIN_PC14,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata carmeva_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PB10,
+		.wp_pin		= AT91_PIN_PC14,
+	},
 };
 
 static struct spi_board_info carmeva_spi_devices[] = {
@@ -150,7 +150,7 @@ static void __init carmeva_board_init(void)
 	/* Compact Flash */
 //	at91_add_device_cf(&carmeva_cf_data);
 	/* MMC */
-	at91_add_device_mmc(0, &carmeva_mmc_data);
+	at91_add_device_mci(0, &carmeva_mci0_data);
 	/* LEDs */
 	at91_gpio_leds(carmeva_leds, ARRAY_SIZE(carmeva_leds));
 }

arch/arm/mach-at91/board-cpu9krea.c

@@ -254,8 +254,7 @@ static struct gpio_led cpu9krea_leds[] = {
 
 static struct i2c_board_info __initdata cpu9krea_i2c_devices[] = {
 	{
-		I2C_BOARD_INFO("rtc-ds1307", 0x68),
-		.type	= "ds1339",
+		I2C_BOARD_INFO("ds1339", 0x68),
 	},
 };
 
@@ -312,12 +311,12 @@ static void __init cpu9krea_add_device_buttons(void)
 /*
  * MCI (SD/MMC)
  */
-static struct at91_mmc_data __initdata cpu9krea_mmc_data = {
-	.slot_b		= 0,
-	.wire4		= 1,
-	.det_pin	= AT91_PIN_PA29,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata cpu9krea_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PA29,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 static void __init cpu9krea_board_init(void)
@@ -359,7 +358,7 @@ static void __init cpu9krea_board_init(void)
 	/* Ethernet */
 	at91_add_device_eth(&cpu9krea_macb_data);
 	/* MMC */
-	at91_add_device_mmc(0, &cpu9krea_mmc_data);
+	at91_add_device_mci(0, &cpu9krea_mci0_data);
 	/* I2C */
 	at91_add_device_i2c(cpu9krea_i2c_devices,
 		ARRAY_SIZE(cpu9krea_i2c_devices));

arch/arm/mach-at91/board-cpuat91.c

@@ -78,11 +78,12 @@ static struct at91_udc_data __initdata cpuat91_udc_data = {
 	.pullup_pin	= AT91_PIN_PC14,
 };
 
-static struct at91_mmc_data __initdata cpuat91_mmc_data = {
-	.det_pin	= AT91_PIN_PC2,
-	.wire4		= 1,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata cpuat91_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PC2,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 static struct physmap_flash_data cpuat91_flash_data = {
@@ -168,7 +169,7 @@ static void __init cpuat91_board_init(void)
 	/* USB Device */
 	at91_add_device_udc(&cpuat91_udc_data);
 	/* MMC */
-	at91_add_device_mmc(0, &cpuat91_mmc_data);
+	at91_add_device_mci(0, &cpuat91_mci0_data);
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* Platform devices */

arch/arm/mach-at91/board-csb337.c

@@ -87,12 +87,12 @@ static struct at91_cf_data __initdata csb337_cf_data = {
 	.rst_pin	= AT91_PIN_PD2,
 };
 
-static struct at91_mmc_data __initdata csb337_mmc_data = {
-	.det_pin	= AT91_PIN_PD5,
-	.slot_b		= 0,
-	.wire4		= 1,
-	.wp_pin		= AT91_PIN_PD6,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata csb337_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PD5,
+		.wp_pin		= AT91_PIN_PD6,
+	},
 };
 
 static struct spi_board_info csb337_spi_devices[] = {
@@ -220,8 +220,6 @@ static struct gpio_led csb_leds[] = {
 
 static void __init csb337_board_init(void)
 {
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
 	/* Serial */
 	/* DBGU on ttyS0 */
 	at91_register_uart(0, 0, 0);
@@ -240,7 +238,7 @@ static void __init csb337_board_init(void)
 	/* SPI */
 	at91_add_device_spi(csb337_spi_devices, ARRAY_SIZE(csb337_spi_devices));
 	/* MMC */
-	at91_add_device_mmc(0, &csb337_mmc_data);
+	at91_add_device_mci(0, &csb337_mci0_data);
 	/* NOR flash */
 	platform_device_register(&csb_flash);
 	/* LEDs */

arch/arm/mach-at91/board-eb9200.c

@@ -70,12 +70,12 @@ static struct at91_cf_data __initdata eb9200_cf_data = {
 	.rst_pin	= AT91_PIN_PC5,
 };
 
-static struct at91_mmc_data __initdata eb9200_mmc_data = {
-	.slot_b		= 0,
-	.wire4		= 1,
-	.det_pin	= -EINVAL,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata eb9200_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= -EINVAL,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 static struct i2c_board_info __initdata eb9200_i2c_devices[] = {
@@ -113,7 +113,7 @@ static void __init eb9200_board_init(void)
 	at91_add_device_spi(NULL, 0);
 	/* MMC */
 	/* only supports 1 or 4 bit interface, not wired through to SPI */
-	at91_add_device_mmc(0, &eb9200_mmc_data);
+	at91_add_device_mci(0, &eb9200_mci0_data);
 }
 
 MACHINE_START(ATEB9200, "Embest ATEB9200")

arch/arm/mach-at91/board-ecbat91.c

@@ -64,12 +64,12 @@ static struct at91_usbh_data __initdata ecb_at91usbh_data = {
 	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
-static struct at91_mmc_data __initdata ecb_at91mmc_data = {
-	.slot_b		= 0,
-	.wire4		= 1,
-	.det_pin	= -EINVAL,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata ecbat91_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= -EINVAL,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 
@@ -138,11 +138,20 @@ static struct spi_board_info __initdata ecb_at91spi_devices[] = {
 	},
 };
 
+/*
+ * LEDs
+ */
+static struct gpio_led ecb_leds[] = {
+	{	/* D1 */
+		.name			= "led1",
+		.gpio			= AT91_PIN_PC7,
+		.active_low		= 1,
+		.default_trigger	= "heartbeat",
+	}
+};
+
 static void __init ecb_at91board_init(void)
 {
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PC7, AT91_PIN_PC7);
-
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
@@ -161,10 +170,13 @@ static void __init ecb_at91board_init(void)
 	at91_add_device_i2c(NULL, 0);
 
 	/* MMC */
-	at91_add_device_mmc(0, &ecb_at91mmc_data);
+	at91_add_device_mci(0, &ecbat91_mci0_data);
 
 	/* SPI */
 	at91_add_device_spi(ecb_at91spi_devices, ARRAY_SIZE(ecb_at91spi_devices));
+
+	/* LEDs */
+	at91_gpio_leds(ecb_leds, ARRAY_SIZE(ecb_leds));
 }
 
 MACHINE_START(ECBAT91, "emQbit's ECB_AT91")

arch/arm/mach-at91/board-eco920.c

@@ -56,12 +56,12 @@ static struct at91_udc_data __initdata eco920_udc_data = {
 	.pullup_pin	= AT91_PIN_PB13,
 };
 
-static struct at91_mmc_data __initdata eco920_mmc_data = {
-	.slot_b		= 0,
-	.wire4		= 0,
-	.det_pin	= -EINVAL,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata eco920_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 1,
+		.detect_pin	= -EINVAL,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 static struct physmap_flash_data eco920_flash_data = {
@@ -93,10 +93,26 @@ static struct spi_board_info eco920_spi_devices[] = {
 	},
 };
 
+/*
+ * LEDs
+ */
+static struct gpio_led eco920_leds[] = {
+	{       /* D1 */
+		.name                   = "led1",
+		.gpio                   = AT91_PIN_PB0,
+		.active_low             = 1,
+		.default_trigger        = "heartbeat",
+	},
+	{       /* D2 */
+		.name                   = "led2",
+		.gpio                   = AT91_PIN_PB1,
+		.active_low             = 1,
+		.default_trigger        = "timer",
+	}
+};
+
 static void __init eco920_board_init(void)
 {
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB0, AT91_PIN_PB1);
 	/* DBGU on ttyS0. (Rx & Tx only */
 	at91_register_uart(0, 0, 0);
 	at91_add_device_serial();
@@ -104,7 +120,7 @@ static void __init eco920_board_init(void)
 	at91_add_device_usbh(&eco920_usbh_data);
 	at91_add_device_udc(&eco920_udc_data);
 
-	at91_add_device_mmc(0, &eco920_mmc_data);
+	at91_add_device_mci(0, &eco920_mci0_data);
 	platform_device_register(&eco920_flash);
 
 	at91_ramc_write(0, AT91_SMC_CSR(7),	AT91_SMC_RWHOLD_(1)
@@ -127,6 +143,8 @@ static void __init eco920_board_init(void)
 	);
 
 	at91_add_device_spi(eco920_spi_devices, ARRAY_SIZE(eco920_spi_devices));
+	/* LEDs */
+	at91_gpio_leds(eco920_leds, ARRAY_SIZE(eco920_leds));
 }
 
 MACHINE_START(ECO920, "eco920")

arch/arm/mach-at91/board-flexibity.c

@@ -75,12 +75,12 @@ static struct spi_board_info flexibity_spi_devices[] = {
 };
 
 /* MCI (SD/MMC) */
-static struct at91_mmc_data __initdata flexibity_mmc_data = {
-	.slot_b		= 0,
-	.wire4		= 1,
-	.det_pin	= AT91_PIN_PC9,
-	.wp_pin		= AT91_PIN_PC4,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata flexibity_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PC9,
+		.wp_pin		= AT91_PIN_PC4,
+	},
 };
 
 /* LEDs */
@@ -152,7 +152,7 @@ static void __init flexibity_board_init(void)
 	at91_add_device_spi(flexibity_spi_devices,
 		ARRAY_SIZE(flexibity_spi_devices));
 	/* MMC */
-	at91_add_device_mmc(0, &flexibity_mmc_data);
+	at91_add_device_mci(0, &flexibity_mci0_data);
 	/* LEDs */
 	at91_gpio_leds(flexibity_leds, ARRAY_SIZE(flexibity_leds));
 }

arch/arm/mach-at91/board-foxg20.c

@@ -86,7 +86,7 @@ static struct at91_udc_data __initdata foxg20_udc_data = {
  * SPI devices.
  */
 static struct spi_board_info foxg20_spi_devices[] = {
-#if !defined(CONFIG_MMC_AT91)
+#if !IS_ENABLED(CONFIG_MMC_ATMELMCI)
 	{
 		.modalias	= "mtd_dataflash",
 		.chip_select	= 1,
@@ -109,12 +109,12 @@ static struct macb_platform_data __initdata foxg20_macb_data = {
  * MCI (SD/MMC)
  * det_pin, wp_pin and vcc_pin are not connected
  */
-static struct at91_mmc_data __initdata foxg20_mmc_data = {
-	.slot_b		= 1,
-	.wire4		= 1,
-	.det_pin	= -EINVAL,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata foxg20_mci0_data = {
+	.slot[1] = {
+		.bus_width	= 4,
+		.detect_pin	= -EINVAL,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 
@@ -247,7 +247,7 @@ static void __init foxg20_board_init(void)
 	/* Ethernet */
 	at91_add_device_eth(&foxg20_macb_data);
 	/* MMC */
-	at91_add_device_mmc(0, &foxg20_mmc_data);
+	at91_add_device_mci(0, &foxg20_mci0_data);
 	/* I2C */
 	at91_add_device_i2c(foxg20_i2c_devices, ARRAY_SIZE(foxg20_i2c_devices));
 	/* LEDs */

arch/arm/mach-at91/board-kafa.c

@@ -66,11 +66,20 @@ static struct at91_udc_data __initdata kafa_udc_data = {
 	.pullup_pin	= AT91_PIN_PB7,
 };
 
+/*
+ * LEDs
+ */
+static struct gpio_led kafa_leds[] = {
+	{	/* D1 */
+		.name			= "led1",
+		.gpio			= AT91_PIN_PB4,
+		.active_low		= 1,
+		.default_trigger	= "heartbeat",
+	},
+};
+
 static void __init kafa_board_init(void)
 {
-	/* Set up the LEDs */
-	at91_init_leds(AT91_PIN_PB4, AT91_PIN_PB4);
-
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
@@ -88,6 +97,8 @@ static void __init kafa_board_init(void)
 	at91_add_device_i2c(NULL, 0);
 	/* SPI */
 	at91_add_device_spi(NULL, 0);
+	/* LEDs */
+	at91_gpio_leds(kafa_leds, ARRAY_SIZE(kafa_leds));
 }
 
 MACHINE_START(KAFA, "Sperry-Sun KAFA")

arch/arm/mach-at91/board-kb9202.c

@@ -69,12 +69,12 @@ static struct at91_udc_data __initdata kb9202_udc_data = {
 	.pullup_pin	= AT91_PIN_PB22,
 };
 
-static struct at91_mmc_data __initdata kb9202_mmc_data = {
-	.det_pin	= AT91_PIN_PB2,
-	.slot_b		= 0,
-	.wire4		= 1,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata kb9202_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PB2,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 static struct mtd_partition __initdata kb9202_nand_partition[] = {
@@ -96,11 +96,26 @@ static struct atmel_nand_data __initdata kb9202_nand_data = {
 	.num_parts	= ARRAY_SIZE(kb9202_nand_partition),
 };
 
+/*
+ * LEDs
+ */
+static struct gpio_led kb9202_leds[] = {
+	{	/* D1 */
+		.name			= "led1",
+		.gpio			= AT91_PIN_PC19,
+		.active_low		= 1,
+		.default_trigger	= "heartbeat",
+	},
+	{	/* D2 */
+		.name			= "led2",
+		.gpio			= AT91_PIN_PC18,
+		.active_low		= 1,
+		.default_trigger	= "timer",
+	}
+};
+
 static void __init kb9202_board_init(void)
 {
-	/* Set up the LEDs */
-	at91_init_leds(AT91_PIN_PC19, AT91_PIN_PC18);
-
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
@@ -121,13 +136,15 @@ static void __init kb9202_board_init(void)
 	/* USB Device */
 	at91_add_device_udc(&kb9202_udc_data);
 	/* MMC */
-	at91_add_device_mmc(0, &kb9202_mmc_data);
+	at91_add_device_mci(0, &kb9202_mci0_data);
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
 	/* SPI */
 	at91_add_device_spi(NULL, 0);
 	/* NAND */
 	at91_add_device_nand(&kb9202_nand_data);
+	/* LEDs */
+	at91_gpio_leds(kb9202_leds, ARRAY_SIZE(kb9202_leds));
 }
 
 MACHINE_START(KB9200, "KB920x")

arch/arm/mach-at91/board-neocore926.c

@@ -138,11 +138,12 @@ static struct spi_board_info neocore926_spi_devices[] = {
 /*
  * MCI (SD/MMC)
  */
-static struct at91_mmc_data __initdata neocore926_mmc_data = {
-	.wire4		= 1,
-	.det_pin	= AT91_PIN_PE18,
-	.wp_pin		= AT91_PIN_PE19,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata neocore926_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PE18,
+		.wp_pin		= AT91_PIN_PE19,
+	},
 };
 
 
@@ -354,7 +355,7 @@ static void __init neocore926_board_init(void)
 	neocore926_add_device_ts();
 
 	/* MMC */
-	at91_add_device_mmc(1, &neocore926_mmc_data);
+	at91_add_device_mci(0, &neocore926_mci0_data);
 
 	/* Ethernet */
 	at91_add_device_eth(&neocore926_macb_data);

arch/arm/mach-at91/board-picotux200.c

@@ -62,12 +62,12 @@ static struct at91_usbh_data __initdata picotux200_usbh_data = {
 	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
-static struct at91_mmc_data __initdata picotux200_mmc_data = {
-	.det_pin	= AT91_PIN_PB27,
-	.slot_b		= 0,
-	.wire4		= 1,
-	.wp_pin		= AT91_PIN_PA17,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata picotux200_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PB27,
+		.wp_pin		= AT91_PIN_PA17,
+	},
 };
 
 #define PICOTUX200_FLASH_BASE	AT91_CHIPSELECT_0
@@ -112,7 +112,7 @@ static void __init picotux200_board_init(void)
 	at91_add_device_i2c(NULL, 0);
 	/* MMC */
 	at91_set_gpio_output(AT91_PIN_PB22, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
-	at91_add_device_mmc(0, &picotux200_mmc_data);
+	at91_add_device_mci(0, &picotux200_mci0_data);
 	/* NOR Flash */
 	platform_device_register(&picotux200_flash);
 }

arch/arm/mach-at91/board-qil-a9260.c

@@ -156,12 +156,12 @@ static void __init ek_add_device_nand(void)
 /*
  * MCI (SD/MMC)
  */
-static struct at91_mmc_data __initdata ek_mmc_data = {
-	.slot_b		= 0,
-	.wire4		= 1,
-	.det_pin	= -EINVAL,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata ek_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= -EINVAL,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 /*
@@ -245,7 +245,7 @@ static void __init ek_board_init(void)
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* MMC */
-	at91_add_device_mmc(0, &ek_mmc_data);
+	at91_add_device_mci(0, &ek_mci0_data);
 	/* Push Buttons */
 	ek_add_device_buttons();
 	/* LEDs */

arch/arm/mach-at91/board-rm9200dk.c

@@ -77,12 +77,12 @@ static struct at91_cf_data __initdata dk_cf_data = {
 };
 
 #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
-static struct at91_mmc_data __initdata dk_mmc_data = {
-	.slot_b		= 0,
-	.wire4		= 1,
-	.det_pin	= -EINVAL,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata dk_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= -EINVAL,
+		.wp_pin		= -EINVAL,
+	},
 };
 #endif
 
@@ -177,9 +177,6 @@ static struct gpio_led dk_leds[] = {
 
 static void __init dk_board_init(void)
 {
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB2, AT91_PIN_PB2);
-
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
@@ -208,7 +205,7 @@ static void __init dk_board_init(void)
 #else
 	/* MMC */
 	at91_set_gpio_output(AT91_PIN_PB7, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
-	at91_add_device_mmc(0, &dk_mmc_data);
+	at91_add_device_mci(0, &dk_mci0_data);
 #endif
 	/* NAND */
 	at91_add_device_nand(&dk_nand_data);

arch/arm/mach-at91/board-rm9200ek.c

@@ -70,12 +70,12 @@ static struct at91_udc_data __initdata ek_udc_data = {
 };
 
 #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
-static struct at91_mmc_data __initdata ek_mmc_data = {
-	.det_pin	= AT91_PIN_PB27,
-	.slot_b		= 0,
-	.wire4		= 1,
-	.wp_pin		= AT91_PIN_PA17,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata ek_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PB27,
+		.wp_pin		= AT91_PIN_PA17,
+	}
 };
 #endif
 
@@ -148,9 +148,6 @@ static struct gpio_led ek_leds[] = {
 
 static void __init ek_board_init(void)
 {
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB1, AT91_PIN_PB2);
-
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
@@ -177,7 +174,7 @@ static void __init ek_board_init(void)
 #else
 	/* MMC */
 	at91_set_gpio_output(AT91_PIN_PB22, 1);	/* this MMC card slot can optionally use SPI signaling (CS3). */
-	at91_add_device_mmc(0, &ek_mmc_data);
+	at91_add_device_mci(0, &ek_mci0_data);
 #endif
 	/* NOR Flash */
 	platform_device_register(&ek_flash);

arch/arm/mach-at91/board-rsi-ews.c

@@ -58,11 +58,12 @@ static struct at91_usbh_data rsi_ews_usbh_data __initdata = {
 /*
  * SD/MC
  */
-static struct at91_mmc_data rsi_ews_mmc_data __initdata = {
-	.slot_b		= 0,
-	.wire4		= 1,
-	.det_pin	= AT91_PIN_PB27,
-	.wp_pin		= AT91_PIN_PB29,
+static struct mci_platform_data __initdata rsi_ews_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PB27,
+		.wp_pin		= AT91_PIN_PB29,
+	},
 };
 
 /*
@@ -185,9 +186,6 @@ static struct platform_device rsiews_nor_flash = {
  */
 static void __init rsi_ews_board_init(void)
 {
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PB6, AT91_PIN_PB9);
-
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	/* This one is for debugging */
@@ -215,7 +213,7 @@ static void __init rsi_ews_board_init(void)
 	at91_add_device_spi(rsi_ews_spi_devices,
 			ARRAY_SIZE(rsi_ews_spi_devices));
 	/* MMC */
-	at91_add_device_mmc(0, &rsi_ews_mmc_data);
+	at91_add_device_mci(0, &rsi_ews_mci0_data);
 	/* NOR Flash */
 	platform_device_register(&rsiews_nor_flash);
 	/* LEDs */

arch/arm/mach-at91/board-sam9-l9260.c

@@ -73,7 +73,7 @@ static struct at91_udc_data __initdata ek_udc_data = {
  * SPI devices.
  */
 static struct spi_board_info ek_spi_devices[] = {
-#if !defined(CONFIG_MMC_AT91)
+#if !IS_ENABLED(CONFIG_MMC_ATMELMCI)
 	{	/* DataFlash chip */
 		.modalias	= "mtd_dataflash",
 		.chip_select	= 1,
@@ -158,19 +158,34 @@ static void __init ek_add_device_nand(void)
 /*
  * MCI (SD/MMC)
  */
-static struct at91_mmc_data __initdata ek_mmc_data = {
-	.slot_b		= 1,
-	.wire4		= 1,
-	.det_pin	= AT91_PIN_PC8,
-	.wp_pin		= AT91_PIN_PC4,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata ek_mci0_data = {
+	.slot[1] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PC8,
+		.wp_pin		= AT91_PIN_PC4,
+	},
+};
+
+/*
+ * LEDs
+ */
+static struct gpio_led ek_leds[] = {
+	{	/* D1 */
+		.name			= "led1",
+		.gpio			= AT91_PIN_PA9,
+		.active_low		= 1,
+		.default_trigger	= "heartbeat",
+	},
+	{	/* D2 */
+		.name			= "led2",
+		.gpio			= AT91_PIN_PA6,
+		.active_low		= 1,
+		.default_trigger	= "timer",
+	}
 };
 
 static void __init ek_board_init(void)
 {
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PA9, AT91_PIN_PA6);
-
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
@@ -194,9 +209,11 @@ static void __init ek_board_init(void)
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* MMC */
-	at91_add_device_mmc(0, &ek_mmc_data);
+	at91_add_device_mci(0, &ek_mci0_data);
 	/* I2C */
 	at91_add_device_i2c(NULL, 0);
+	/* LEDs */
+	at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
 }
 
 MACHINE_START(SAM9_L9260, "Olimex SAM9-L9260")

arch/arm/mach-at91/board-sam9260ek.c

@@ -108,7 +108,7 @@ static void __init at73c213_set_clk(struct at73c213_board_info *info) {}
  * SPI devices.
  */
 static struct spi_board_info ek_spi_devices[] = {
-#if !defined(CONFIG_MMC_AT91)
+#if !IS_ENABLED(CONFIG_MMC_ATMELMCI)
 	{	/* DataFlash chip */
 		.modalias	= "mtd_dataflash",
 		.chip_select	= 1,
@@ -211,12 +211,12 @@ static void __init ek_add_device_nand(void)
 /*
  * MCI (SD/MMC)
  */
-static struct at91_mmc_data __initdata ek_mmc_data = {
-	.slot_b		= 1,
-	.wire4		= 1,
-	.det_pin	= -EINVAL,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata ek_mci0_data = {
+	.slot[1] = {
+		.bus_width	= 4,
+		.detect_pin	= -EINVAL,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 
@@ -329,7 +329,7 @@ static void __init ek_board_init(void)
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* MMC */
-	at91_add_device_mmc(0, &ek_mmc_data);
+	at91_add_device_mci(0, &ek_mci0_data);
 	/* I2C */
 	at91_add_device_i2c(ek_i2c_devices, ARRAY_SIZE(ek_i2c_devices));
 	/* SSC (to AT73C213) */

arch/arm/mach-at91/board-sam9261ek.c

@@ -340,11 +340,12 @@ static struct spi_board_info ek_spi_devices[] = {
  * MCI (SD/MMC)
  * det_pin, wp_pin and vcc_pin are not connected
  */
-static struct at91_mmc_data __initdata ek_mmc_data = {
-	.wire4		= 1,
-	.det_pin	= -EINVAL,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= -EINVAL,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 #endif /* CONFIG_SPI_ATMEL_* */
@@ -569,9 +570,6 @@ static struct gpio_led ek_leds[] = {
 
 static void __init ek_board_init(void)
 {
-	/* Setup the LEDs */
-	at91_init_leds(AT91_PIN_PA13, AT91_PIN_PA14);
-
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
@@ -598,7 +596,7 @@ static void __init ek_board_init(void)
 	at91_add_device_ssc(AT91SAM9261_ID_SSC1, ATMEL_SSC_TX);
 #else
 	/* MMC */
-	at91_add_device_mmc(0, &ek_mmc_data);
+	at91_add_device_mci(0, &mci0_data);
 #endif
 	/* LCD Controller */
 	at91_add_device_lcdc(&ek_lcdc_data);

arch/arm/mach-at91/board-sam9263ek.c

@@ -141,11 +141,12 @@ static struct spi_board_info ek_spi_devices[] = {
 /*
  * MCI (SD/MMC)
  */
-static struct at91_mmc_data __initdata ek_mmc_data = {
-	.wire4		= 1,
-	.det_pin	= AT91_PIN_PE18,
-	.wp_pin		= AT91_PIN_PE19,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata mci1_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PE18,
+		.wp_pin		= AT91_PIN_PE19,
+	},
 };
 
 
@@ -420,7 +421,7 @@ static void __init ek_board_init(void)
 	/* Touchscreen */
 	ek_add_device_ts();
 	/* MMC */
-	at91_add_device_mmc(1, &ek_mmc_data);
+	at91_add_device_mci(1, &mci1_data);
 	/* Ethernet */
 	at91_add_device_eth(&ek_macb_data);
 	/* NAND */

arch/arm/mach-at91/board-sam9g20ek.c

@@ -92,7 +92,7 @@ static struct at91_udc_data __initdata ek_udc_data = {
  * SPI devices.
  */
 static struct spi_board_info ek_spi_devices[] = {
-#if !(defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_AT91))
+#if !IS_ENABLED(CONFIG_MMC_ATMELMCI)
 	{	/* DataFlash chip */
 		.modalias	= "mtd_dataflash",
 		.chip_select	= 1,
@@ -199,7 +199,6 @@ static void __init ek_add_device_nand(void)
  * MCI (SD/MMC)
  * wp_pin and vcc_pin are not connected
  */
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
 static struct mci_platform_data __initdata ek_mmc_data = {
 	.slot[1] = {
 		.bus_width	= 4,
@@ -208,28 +207,15 @@ static struct mci_platform_data __initdata ek_mmc_data = {
 	},
 
 };
-#else
-static struct at91_mmc_data __initdata ek_mmc_data = {
-	.slot_b		= 1,	/* Only one slot so use slot B */
-	.wire4		= 1,
-	.det_pin	= AT91_PIN_PC9,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
-};
-#endif
 
 static void __init ek_add_device_mmc(void)
 {
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
 	if (ek_have_2mmc()) {
 		ek_mmc_data.slot[0].bus_width = 4;
 		ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2;
 		ek_mmc_data.slot[0].wp_pin = -1;
 	}
 	at91_add_device_mci(0, &ek_mmc_data);
-#else
-	at91_add_device_mmc(0, &ek_mmc_data);
-#endif
 }
 
 /*

arch/arm/mach-at91/board-sam9rlek.c

@@ -56,11 +56,12 @@ static struct usba_platform_data __initdata ek_usba_udc_data = {
 /*
  * MCI (SD/MMC)
  */
-static struct at91_mmc_data __initdata ek_mmc_data = {
-	.wire4		= 1,
-	.det_pin	= AT91_PIN_PA15,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PA15,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 
@@ -303,7 +304,7 @@ static void __init ek_board_init(void)
 	/* SPI */
 	at91_add_device_spi(ek_spi_devices, ARRAY_SIZE(ek_spi_devices));
 	/* MMC */
-	at91_add_device_mmc(0, &ek_mmc_data);
+	at91_add_device_mci(0, &mci0_data);
 	/* LCD Controller */
 	at91_add_device_lcdc(&ek_lcdc_data);
 	/* AC97 */

arch/arm/mach-at91/board-stamp9g20.c

@@ -83,7 +83,6 @@ static void __init add_device_nand(void)
  * MCI (SD/MMC)
  * det_pin, wp_pin and vcc_pin are not connected
  */
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
 static struct mci_platform_data __initdata mmc_data = {
 	.slot[0] = {
 		.bus_width	= 4,
@@ -91,15 +90,6 @@ static struct mci_platform_data __initdata mmc_data = {
 		.wp_pin		= -1,
 	},
 };
-#else
-static struct at91_mmc_data __initdata mmc_data = {
-	.slot_b		= 0,
-	.wire4		= 1,
-	.det_pin	= -EINVAL,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
-};
-#endif
 
 
 /*
@@ -223,11 +213,7 @@ void __init stamp9g20_board_init(void)
 	/* NAND */
 	add_device_nand();
 	/* MMC */
-#if defined(CONFIG_MMC_ATMELMCI) || defined(CONFIG_MMC_ATMELMCI_MODULE)
 	at91_add_device_mci(0, &mmc_data);
-#else
-	at91_add_device_mmc(0, &mmc_data);
-#endif
 	/* W1 */
 	add_w1();
 }

arch/arm/mach-at91/board-usb-a926x.c

@@ -109,14 +109,12 @@ static struct mmc_spi_platform_data at91_mmc_spi_pdata = {
  * SPI devices.
  */
 static struct spi_board_info usb_a9263_spi_devices[] = {
-#if !defined(CONFIG_MMC_AT91)
 	{	/* DataFlash chip */
 		.modalias	= "mtd_dataflash",
 		.chip_select	= 0,
 		.max_speed_hz	= 15 * 1000 * 1000,
 		.bus_num	= 0,
 	}
-#endif
 };
 
 static struct spi_board_info usb_a9g20_spi_devices[] = {

arch/arm/mach-at91/board-yl-9200.c

@@ -119,11 +119,12 @@ static struct at91_udc_data __initdata yl9200_udc_data = {
 /*
  * MMC
  */
-static struct at91_mmc_data __initdata yl9200_mmc_data = {
-	.det_pin	= AT91_PIN_PB9,
-	.wire4		= 1,
-	.wp_pin		= -EINVAL,
-	.vcc_pin	= -EINVAL,
+static struct mci_platform_data __initdata yl9200_mci0_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PB9,
+		.wp_pin		= -EINVAL,
+	},
 };
 
 /*
@@ -541,9 +542,6 @@ void __init yl9200_add_device_video(void) {}
 
 static void __init yl9200_board_init(void)
 {
-	/* Setup the LEDs D2=PB17 (timer), D3=PB16 (cpu) */
-	at91_init_leds(AT91_PIN_PB16, AT91_PIN_PB17);
-
 	/* Serial */
 	/* DBGU on ttyS0. (Rx & Tx only) */
 	at91_register_uart(0, 0, 0);
@@ -568,7 +566,7 @@ static void __init yl9200_board_init(void)
 	/* I2C */
 	at91_add_device_i2c(yl9200_i2c_devices, ARRAY_SIZE(yl9200_i2c_devices));
 	/* MMC */
-	at91_add_device_mmc(0, &yl9200_mmc_data);
+	at91_add_device_mci(0, &yl9200_mci0_data);
 	/* NAND */
 	at91_add_device_nand(&yl9200_nand_data);
 	/* NOR Flash */

arch/arm/mach-at91/include/mach/board.h

@@ -187,7 +187,6 @@ struct at91_can_data {
 extern void __init at91_add_device_can(struct at91_can_data *data);
 
  /* LEDs */
-extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
 extern void __init at91_gpio_leds(struct gpio_led *leds, int nr);
 extern void __init at91_pwm_leds(struct gpio_led *leds, int nr);
 

arch/arm/mach-at91/leds.c

@@ -90,108 +90,3 @@ void __init at91_pwm_leds(struct gpio_led *leds, int nr)
 #else
 void __init at91_pwm_leds(struct gpio_led *leds, int nr){}
 #endif
-
-
-/* ------------------------------------------------------------------------- */
-
-#if defined(CONFIG_LEDS)
-
-#include <asm/leds.h>
-
-/*
- * Old ARM-specific LED framework; not fully functional when generic time is
- * in use.
- */
-
-static u8 at91_leds_cpu;
-static u8 at91_leds_timer;
-
-static inline void at91_led_on(unsigned int led)
-{
-	at91_set_gpio_value(led, 0);
-}
-
-static inline void at91_led_off(unsigned int led)
-{
-	at91_set_gpio_value(led, 1);
-}
-
-static inline void at91_led_toggle(unsigned int led)
-{
-	unsigned long is_off = at91_get_gpio_value(led);
-	if (is_off)
-		at91_led_on(led);
-	else
-		at91_led_off(led);
-}
-
-
-/*
- * Handle LED events.
- */
-static void at91_leds_event(led_event_t evt)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-
-	switch(evt) {
-	case led_start:		/* System startup */
-		at91_led_on(at91_leds_cpu);
-		break;
-
-	case led_stop:		/* System stop / suspend */
-		at91_led_off(at91_leds_cpu);
-		break;
-
-#ifdef CONFIG_LEDS_TIMER
-	case led_timer:		/* Every 50 timer ticks */
-		at91_led_toggle(at91_leds_timer);
-		break;
-#endif
-
-#ifdef CONFIG_LEDS_CPU
-	case led_idle_start:	/* Entering idle state */
-		at91_led_off(at91_leds_cpu);
-		break;
-
-	case led_idle_end:	/* Exit idle state */
-		at91_led_on(at91_leds_cpu);
-		break;
-#endif
-
-	default:
-		break;
-	}
-
-	local_irq_restore(flags);
-}
-
-
-static int __init leds_init(void)
-{
-	if (!at91_leds_timer || !at91_leds_cpu)
-		return -ENODEV;
-
-	leds_event = at91_leds_event;
-
-	leds_event(led_start);
-	return 0;
-}
-
-__initcall(leds_init);
-
-
-void __init at91_init_leds(u8 cpu_led, u8 timer_led)
-{
-	/* Enable GPIO to access the LEDs */
-	at91_set_gpio_output(cpu_led, 1);
-	at91_set_gpio_output(timer_led, 1);
-
-	at91_leds_cpu	= cpu_led;
-	at91_leds_timer	= timer_led;
-}
-
-#else
-void __init at91_init_leds(u8 cpu_led, u8 timer_led) {}
-#endif

arch/arm/mach-clps711x/Makefile

@@ -15,5 +15,3 @@ obj-$(CONFIG_ARCH_CLEP7312) += clep7312.o
 obj-$(CONFIG_ARCH_EDB7211)  += edb7211-arch.o edb7211-mm.o
 obj-$(CONFIG_ARCH_FORTUNET) += fortunet.o
 obj-$(CONFIG_ARCH_P720T)    += p720t.o
-leds-$(CONFIG_ARCH_P720T)   += p720t-leds.o
-obj-$(CONFIG_LEDS)          += $(leds-y)

arch/arm/mach-clps711x/p720t-leds.c

@@ -1,63 +0,0 @@
-/*
- *  linux/arch/arm/mach-clps711x/leds.c
- *
- *  Integrator LED control routines
- *
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/io.h>
-
-#include <mach/hardware.h>
-#include <asm/leds.h>
-#include <asm/mach-types.h>
-
-static void p720t_leds_event(led_event_t ledevt)
-{
-	unsigned long flags;
-	u32 pddr;
-
-	local_irq_save(flags);
-	switch(ledevt) {
-	case led_idle_start:
-		break;
-
-	case led_idle_end:
-		break;
-
-	case led_timer:
-		pddr = clps_readb(PDDR);
-		clps_writeb(pddr ^ 1, PDDR);
-		break;
-
-	default:
-		break;
-	}
-
-	local_irq_restore(flags);
-}
-
-static int __init leds_init(void)
-{
-	if (machine_is_p720t())
-		leds_event = p720t_leds_event;
-
-	return 0;
-}
-
-arch_initcall(leds_init);

arch/arm/mach-clps711x/p720t.c

@@ -23,6 +23,8 @@
 #include <linux/string.h>
 #include <linux/mm.h>
 #include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/leds.h>
 
 #include <mach/hardware.h>
 #include <asm/pgtable.h>
@@ -34,6 +36,8 @@
 #include <asm/mach/map.h>
 #include <mach/syspld.h>
 
+#include <asm/hardware/clps7111.h>
+
 #include "common.h"
 
 /*
@@ -107,6 +111,64 @@ static void __init p720t_init_early(void)
 	}
 }
 
+/*
+ * LED controled by CPLD
+ */
+#if defined(CONFIG_NEW_LEDS) && defined(CONFIG_LEDS_CLASS)
+static void p720t_led_set(struct led_classdev *cdev,
+			      enum led_brightness b)
+{
+	u8 reg = clps_readb(PDDR);
+
+	if (b != LED_OFF)
+		reg |= 0x1;
+	else
+		reg &= ~0x1;
+
+	clps_writeb(reg, PDDR);
+}
+
+static enum led_brightness p720t_led_get(struct led_classdev *cdev)
+{
+	u8 reg = clps_readb(PDDR);
+
+	return (reg & 0x1) ? LED_FULL : LED_OFF;
+}
+
+static int __init p720t_leds_init(void)
+{
+
+	struct led_classdev *cdev;
+	int ret;
+
+	if (!machine_is_p720t())
+		return -ENODEV;
+
+	cdev = kzalloc(sizeof(*cdev), GFP_KERNEL);
+	if (!cdev)
+		return -ENOMEM;
+
+	cdev->name = "p720t:0";
+	cdev->brightness_set = p720t_led_set;
+	cdev->brightness_get = p720t_led_get;
+	cdev->default_trigger = "heartbeat";
+
+	ret = led_classdev_register(NULL, cdev);
+	if (ret	< 0) {
+		kfree(cdev);
+		return ret;
+	}
+
+	return 0;
+}
+
+/*
+ * Since we may have triggers on any subsystem, defer registration
+ * until after subsystem_init.
+ */
+fs_initcall(p720t_leds_init);
+#endif
+
 MACHINE_START(P720T, "ARM-Prospector720T")
 	/* Maintainer: ARM Ltd/Deep Blue Solutions Ltd */
 	.atag_offset	= 0x100,

arch/arm/mach-ebsa110/Makefile

@@ -4,9 +4,7 @@
 
 # Object file lists.
 
-obj-y			:= core.o io.o
+obj-y			:= core.o io.o leds.o
 obj-m			:=
 obj-n			:=
 obj-			:=
-
-obj-$(CONFIG_LEDS)	+= leds.o

arch/arm/mach-ebsa110/leds.c

@@ -1,52 +1,71 @@
 /*
- *  linux/arch/arm/mach-ebsa110/leds.c
+ * Driver for the LED found on the EBSA110 machine
+ * Based on Versatile and RealView machine LED code
  *
- *  Copyright (C) 1998 Russell King
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- *  EBSA-110 LED control routines.  We use the led as follows:
- *
- *   - Red - toggles state every 50 timer interrupts
+ * License terms: GNU General Public License (GPL) version 2
+ * Author: Bryan Wu <bryan.wu@canonical.com>
  */
-#include <linux/module.h>
-#include <linux/spinlock.h>
+#include <linux/kernel.h>
 #include <linux/init.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/leds.h>
 
-#include <mach/hardware.h>
-#include <asm/leds.h>
 #include <asm/mach-types.h>
 
 #include "core.h"
 
-static spinlock_t leds_lock;
-
-static void ebsa110_leds_event(led_event_t ledevt)
+#if defined(CONFIG_NEW_LEDS) && defined(CONFIG_LEDS_CLASS)
+static void ebsa110_led_set(struct led_classdev *cdev,
+			      enum led_brightness b)
 {
-	unsigned long flags;
+	u8 reg = __raw_readb(SOFT_BASE);
 
-	spin_lock_irqsave(&leds_lock, flags);
+	if (b != LED_OFF)
+		reg |= 0x80;
+	else
+		reg &= ~0x80;
 
-	switch(ledevt) {
-	case led_timer:
-		*(volatile unsigned char *)SOFT_BASE ^= 128;
-		break;
+	__raw_writeb(reg, SOFT_BASE);
+}
 
-	default:
-		break;
-	}
+static enum led_brightness ebsa110_led_get(struct led_classdev *cdev)
+{
+	u8 reg = __raw_readb(SOFT_BASE);
 
-	spin_unlock_irqrestore(&leds_lock, flags);
+	return (reg & 0x80) ? LED_FULL : LED_OFF;
 }
 
-static int __init leds_init(void)
+static int __init ebsa110_leds_init(void)
 {
-	if (machine_is_ebsa110())
-		leds_event = ebsa110_leds_event;
+
+	struct led_classdev *cdev;
+	int ret;
+
+	if (!machine_is_ebsa110())
+		return -ENODEV;
+
+	cdev = kzalloc(sizeof(*cdev), GFP_KERNEL);
+	if (!cdev)
+		return -ENOMEM;
+
+	cdev->name = "ebsa110:0";
+	cdev->brightness_set = ebsa110_led_set;
+	cdev->brightness_get = ebsa110_led_get;
+	cdev->default_trigger = "heartbeat";
+
+	ret = led_classdev_register(NULL, cdev);
+	if (ret	< 0) {
+		kfree(cdev);
+		return ret;
+	}
 
 	return 0;
 }
 
-__initcall(leds_init);
+/*
+ * Since we may have triggers on any subsystem, defer registration
+ * until after subsystem_init.
+ */
+fs_initcall(ebsa110_leds_init);
+#endif

arch/arm/mach-exynos/Kconfig

@@ -405,6 +405,8 @@ config MACH_EXYNOS4_DT
 	select USE_OF
 	select ARM_AMBA
 	select HAVE_SAMSUNG_KEYPAD if INPUT_KEYBOARD
+	select PINCTRL
+	select PINCTRL_EXYNOS4
 	help
 	  Machine support for Samsung Exynos4 machine with device tree enabled.
 	  Select this if a fdt blob is available for the Exynos4 SoC based board.

arch/arm/mach-exynos/clock-exynos5.c

@@ -547,6 +547,68 @@ static struct clksrc_clk exynos5_clk_aclk_66 = {
 	.reg_div = { .reg = EXYNOS5_CLKDIV_TOP0, .shift = 0, .size = 3 },
 };
 
+static struct clksrc_clk exynos5_clk_mout_aclk_300_gscl_mid = {
+	.clk	= {
+		.name		= "mout_aclk_300_gscl_mid",
+	},
+	.sources = &exynos5_clkset_aclk,
+	.reg_src = { .reg = EXYNOS5_CLKSRC_TOP0, .shift = 24, .size = 1 },
+};
+
+static struct clk *exynos5_clkset_aclk_300_mid1_list[] = {
+	[0] = &exynos5_clk_sclk_vpll.clk,
+	[1] = &exynos5_clk_mout_cpll.clk,
+};
+
+static struct clksrc_sources exynos5_clkset_aclk_300_gscl_mid1 = {
+	.sources	= exynos5_clkset_aclk_300_mid1_list,
+	.nr_sources	= ARRAY_SIZE(exynos5_clkset_aclk_300_mid1_list),
+};
+
+static struct clksrc_clk exynos5_clk_mout_aclk_300_gscl_mid1 = {
+	.clk	= {
+		.name		= "mout_aclk_300_gscl_mid1",
+	},
+	.sources = &exynos5_clkset_aclk_300_gscl_mid1,
+	.reg_src = { .reg = EXYNOS5_CLKSRC_TOP1, .shift = 12, .size = 1 },
+};
+
+static struct clk *exynos5_clkset_aclk_300_gscl_list[] = {
+	[0] = &exynos5_clk_mout_aclk_300_gscl_mid.clk,
+	[1] = &exynos5_clk_mout_aclk_300_gscl_mid1.clk,
+};
+
+static struct clksrc_sources exynos5_clkset_aclk_300_gscl = {
+	.sources	= exynos5_clkset_aclk_300_gscl_list,
+	.nr_sources	= ARRAY_SIZE(exynos5_clkset_aclk_300_gscl_list),
+};
+
+static struct clksrc_clk exynos5_clk_mout_aclk_300_gscl = {
+	.clk	= {
+		.name		= "mout_aclk_300_gscl",
+	},
+	.sources = &exynos5_clkset_aclk_300_gscl,
+	.reg_src = { .reg = EXYNOS5_CLKSRC_TOP0, .shift = 25, .size = 1 },
+};
+
+static struct clk *exynos5_clk_src_gscl_300_list[] = {
+	[0] = &clk_ext_xtal_mux,
+	[1] = &exynos5_clk_mout_aclk_300_gscl.clk,
+};
+
+static struct clksrc_sources exynos5_clk_src_gscl_300 = {
+	.sources	= exynos5_clk_src_gscl_300_list,
+	.nr_sources	= ARRAY_SIZE(exynos5_clk_src_gscl_300_list),
+};
+
+static struct clksrc_clk exynos5_clk_aclk_300_gscl = {
+	.clk	= {
+		.name		= "aclk_300_gscl",
+	},
+	.sources = &exynos5_clk_src_gscl_300,
+	.reg_src = { .reg = EXYNOS5_CLKSRC_TOP3, .shift = 10, .size = 1 },
+};
+
 static struct clk exynos5_init_clocks_off[] = {
 	{
 		.name		= "timers",
@@ -754,6 +816,26 @@ static struct clk exynos5_init_clocks_off[] = {
 		.parent		= &exynos5_clk_aclk_66.clk,
 		.enable		= exynos5_clk_ip_peric_ctrl,
 		.ctrlbit	= (1 << 18),
+	}, {
+		.name		= "gscl",
+		.devname	= "exynos-gsc.0",
+		.enable		= exynos5_clk_ip_gscl_ctrl,
+		.ctrlbit	= (1 << 0),
+	}, {
+		.name		= "gscl",
+		.devname	= "exynos-gsc.1",
+		.enable		= exynos5_clk_ip_gscl_ctrl,
+		.ctrlbit	= (1 << 1),
+	}, {
+		.name		= "gscl",
+		.devname	= "exynos-gsc.2",
+		.enable		= exynos5_clk_ip_gscl_ctrl,
+		.ctrlbit	= (1 << 2),
+	}, {
+		.name		= "gscl",
+		.devname	= "exynos-gsc.3",
+		.enable		= exynos5_clk_ip_gscl_ctrl,
+		.ctrlbit	= (1 << 3),
 	}, {
 		.name		= SYSMMU_CLOCK_NAME,
 		.devname	= SYSMMU_CLOCK_DEVNAME(mfc_l, 0),
@@ -1225,6 +1307,10 @@ static struct clksrc_clk *exynos5_sysclks[] = {
 	&exynos5_clk_aclk_266,
 	&exynos5_clk_aclk_200,
 	&exynos5_clk_aclk_166,
+	&exynos5_clk_aclk_300_gscl,
+	&exynos5_clk_mout_aclk_300_gscl,
+	&exynos5_clk_mout_aclk_300_gscl_mid,
+	&exynos5_clk_mout_aclk_300_gscl_mid1,
 	&exynos5_clk_aclk_66_pre,
 	&exynos5_clk_aclk_66,
 	&exynos5_clk_dout_mmc0,

arch/arm/mach-exynos/common.c

@@ -980,6 +980,32 @@ static int __init exynos_init_irq_eint(void)
 {
 	int irq;
 
+#ifdef CONFIG_PINCTRL_SAMSUNG
+	/*
+	 * The Samsung pinctrl driver provides an integrated gpio/pinmux/pinconf
+	 * functionality along with support for external gpio and wakeup
+	 * interrupts. If the samsung pinctrl driver is enabled and includes
+	 * the wakeup interrupt support, then the setting up external wakeup
+	 * interrupts here can be skipped. This check here is temporary to
+	 * allow exynos4 platforms that do not use Samsung pinctrl driver to
+	 * co-exist with platforms that do. When all of the Samsung Exynos4
+	 * platforms switch over to using the pinctrl driver, the wakeup
+	 * interrupt support code here can be completely removed.
+	 */
+	struct device_node *pctrl_np, *wkup_np;
+	const char *pctrl_compat = "samsung,pinctrl-exynos4210";
+	const char *wkup_compat = "samsung,exynos4210-wakeup-eint";
+
+	for_each_compatible_node(pctrl_np, NULL, pctrl_compat) {
+		if (of_device_is_available(pctrl_np)) {
+			wkup_np = of_find_compatible_node(pctrl_np, NULL,
+							wkup_compat);
+			if (wkup_np)
+				return -ENODEV;
+		}
+	}
+#endif
+
 	if (soc_is_exynos5250())
 		exynos_eint_base = ioremap(EXYNOS5_PA_GPIO1, SZ_4K);
 	else

arch/arm/mach-exynos/include/mach/map.h

@@ -121,6 +121,11 @@
 #define EXYNOS4_PA_SYSMMU_MFC_L		0x13620000
 #define EXYNOS4_PA_SYSMMU_MFC_R		0x13630000
 
+#define EXYNOS5_PA_GSC0			0x13E00000
+#define EXYNOS5_PA_GSC1			0x13E10000
+#define EXYNOS5_PA_GSC2			0x13E20000
+#define EXYNOS5_PA_GSC3			0x13E30000
+
 #define EXYNOS5_PA_SYSMMU_MDMA1		0x10A40000
 #define EXYNOS5_PA_SYSMMU_SSS		0x10A50000
 #define EXYNOS5_PA_SYSMMU_2D		0x10A60000

arch/arm/mach-exynos/mach-exynos5-dt.c

@@ -56,6 +56,14 @@ static const struct of_dev_auxdata exynos5250_auxdata_lookup[] __initconst = {
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS5_PA_PDMA0, "dma-pl330.0", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS5_PA_PDMA1, "dma-pl330.1", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS5_PA_MDMA1, "dma-pl330.2", NULL),
+	OF_DEV_AUXDATA("samsung,exynos5-gsc", EXYNOS5_PA_GSC0,
+				"exynos-gsc.0", NULL),
+	OF_DEV_AUXDATA("samsung,exynos5-gsc", EXYNOS5_PA_GSC1,
+				"exynos-gsc.1", NULL),
+	OF_DEV_AUXDATA("samsung,exynos5-gsc", EXYNOS5_PA_GSC2,
+				"exynos-gsc.2", NULL),
+	OF_DEV_AUXDATA("samsung,exynos5-gsc", EXYNOS5_PA_GSC3,
+				"exynos-gsc.3", NULL),
 	{},
 };
 

arch/arm/mach-footbridge/Makefile

@@ -14,15 +14,11 @@ pci-$(CONFIG_ARCH_EBSA285_HOST) += ebsa285-pci.o
 pci-$(CONFIG_ARCH_NETWINDER) += netwinder-pci.o
 pci-$(CONFIG_ARCH_PERSONAL_SERVER) += personal-pci.o
 
-leds-$(CONFIG_ARCH_EBSA285) += ebsa285-leds.o
-leds-$(CONFIG_ARCH_NETWINDER) += netwinder-leds.o
-
 obj-$(CONFIG_ARCH_CATS) += cats-hw.o isa-timer.o
 obj-$(CONFIG_ARCH_EBSA285) += ebsa285.o dc21285-timer.o
 obj-$(CONFIG_ARCH_NETWINDER) += netwinder-hw.o isa-timer.o
 obj-$(CONFIG_ARCH_PERSONAL_SERVER) += personal.o dc21285-timer.o
 
 obj-$(CONFIG_PCI)	+=$(pci-y)
-obj-$(CONFIG_LEDS)	+=$(leds-y)
 
 obj-$(CONFIG_ISA)	+= isa.o isa-rtc.o

arch/arm/mach-footbridge/ebsa285-leds.c

@@ -1,138 +0,0 @@
-/*
- *  linux/arch/arm/mach-footbridge/ebsa285-leds.c
- *
- *  Copyright (C) 1998-1999 Russell King
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- * EBSA-285 control routines.
- *
- * The EBSA-285 uses the leds as follows:
- *  - Green - toggles state every 50 timer interrupts
- *  - Amber - On if system is not idle
- *  - Red   - currently unused
- *
- * Changelog:
- *   02-05-1999	RMK	Various cleanups
- */
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-
-#include <mach/hardware.h>
-#include <asm/leds.h>
-#include <asm/mach-types.h>
-
-#define LED_STATE_ENABLED	1
-#define LED_STATE_CLAIMED	2
-static char led_state;
-static char hw_led_state;
-
-static DEFINE_SPINLOCK(leds_lock);
-
-static void ebsa285_leds_event(led_event_t evt)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&leds_lock, flags);
-
-	switch (evt) {
-	case led_start:
-		hw_led_state = XBUS_LED_RED | XBUS_LED_GREEN;
-#ifndef CONFIG_LEDS_CPU
-		hw_led_state |= XBUS_LED_AMBER;
-#endif
-		led_state |= LED_STATE_ENABLED;
-		break;
-
-	case led_stop:
-		led_state &= ~LED_STATE_ENABLED;
-		break;
-
-	case led_claim:
-		led_state |= LED_STATE_CLAIMED;
-		hw_led_state = XBUS_LED_RED | XBUS_LED_GREEN | XBUS_LED_AMBER;
-		break;
-
-	case led_release:
-		led_state &= ~LED_STATE_CLAIMED;
-		hw_led_state = XBUS_LED_RED | XBUS_LED_GREEN | XBUS_LED_AMBER;
-		break;
-
-#ifdef CONFIG_LEDS_TIMER
-	case led_timer:
-		if (!(led_state & LED_STATE_CLAIMED))
-			hw_led_state ^= XBUS_LED_GREEN;
-		break;
-#endif
-
-#ifdef CONFIG_LEDS_CPU
-	case led_idle_start:
-		if (!(led_state & LED_STATE_CLAIMED))
-			hw_led_state |= XBUS_LED_AMBER;
-		break;
-
-	case led_idle_end:
-		if (!(led_state & LED_STATE_CLAIMED))
-			hw_led_state &= ~XBUS_LED_AMBER;
-		break;
-#endif
-
-	case led_halted:
-		if (!(led_state & LED_STATE_CLAIMED))
-			hw_led_state &= ~XBUS_LED_RED;
-		break;
-
-	case led_green_on:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state &= ~XBUS_LED_GREEN;
-		break;
-
-	case led_green_off:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state |= XBUS_LED_GREEN;
-		break;
-
-	case led_amber_on:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state &= ~XBUS_LED_AMBER;
-		break;
-
-	case led_amber_off:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state |= XBUS_LED_AMBER;
-		break;
-
-	case led_red_on:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state &= ~XBUS_LED_RED;
-		break;
-
-	case led_red_off:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state |= XBUS_LED_RED;
-		break;
-
-	default:
-		break;
-	}
-
-	if  (led_state & LED_STATE_ENABLED)
-		*XBUS_LEDS = hw_led_state;
-
-	spin_unlock_irqrestore(&leds_lock, flags);
-}
-
-static int __init leds_init(void)
-{
-	if (machine_is_ebsa285())
-		leds_event = ebsa285_leds_event;
-
-	leds_event(led_start);
-
-	return 0;
-}
-
-__initcall(leds_init);

arch/arm/mach-footbridge/ebsa285.c

@@ -5,6 +5,8 @@
  */
 #include <linux/init.h>
 #include <linux/spinlock.h>
+#include <linux/slab.h>
+#include <linux/leds.h>
 
 #include <asm/hardware/dec21285.h>
 #include <asm/mach-types.h>
@@ -13,6 +15,85 @@
 
 #include "common.h"
 
+/* LEDs */
+#if defined(CONFIG_NEW_LEDS) && defined(CONFIG_LEDS_CLASS)
+struct ebsa285_led {
+	struct led_classdev     cdev;
+	u8                      mask;
+};
+
+/*
+ * The triggers lines up below will only be used if the
+ * LED triggers are compiled in.
+ */
+static const struct {
+	const char *name;
+	const char *trigger;
+} ebsa285_leds[] = {
+	{ "ebsa285:amber", "heartbeat", },
+	{ "ebsa285:green", "cpu0", },
+	{ "ebsa285:red",},
+};
+
+static void ebsa285_led_set(struct led_classdev *cdev,
+		enum led_brightness b)
+{
+	struct ebsa285_led *led = container_of(cdev,
+			struct ebsa285_led, cdev);
+
+	if (b != LED_OFF)
+		*XBUS_LEDS |= led->mask;
+	else
+		*XBUS_LEDS &= ~led->mask;
+}
+
+static enum led_brightness ebsa285_led_get(struct led_classdev *cdev)
+{
+	struct ebsa285_led *led = container_of(cdev,
+			struct ebsa285_led, cdev);
+
+	return (*XBUS_LEDS & led->mask) ? LED_FULL : LED_OFF;
+}
+
+static int __init ebsa285_leds_init(void)
+{
+	int i;
+
+	if (machine_is_ebsa285())
+		return -ENODEV;
+
+	/* 3 LEDS All ON */
+	*XBUS_LEDS |= XBUS_LED_AMBER | XBUS_LED_GREEN | XBUS_LED_RED;
+
+	for (i = 0; i < ARRAY_SIZE(ebsa285_leds); i++) {
+		struct ebsa285_led *led;
+
+		led = kzalloc(sizeof(*led), GFP_KERNEL);
+		if (!led)
+			break;
+
+		led->cdev.name = ebsa285_leds[i].name;
+		led->cdev.brightness_set = ebsa285_led_set;
+		led->cdev.brightness_get = ebsa285_led_get;
+		led->cdev.default_trigger = ebsa285_leds[i].trigger;
+		led->mask = BIT(i);
+
+		if (led_classdev_register(NULL, &led->cdev) < 0) {
+			kfree(led);
+			break;
+		}
+	}
+
+	return 0;
+}
+
+/*
+ * Since we may have triggers on any subsystem, defer registration
+ * until after subsystem_init.
+ */
+fs_initcall(ebsa285_leds_init);
+#endif
+
 MACHINE_START(EBSA285, "EBSA285")
 	/* Maintainer: Russell King */
 	.atag_offset	= 0x100,

arch/arm/mach-footbridge/netwinder-hw.c

@@ -12,9 +12,10 @@
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/spinlock.h>
+#include <linux/slab.h>
+#include <linux/leds.h>
 
 #include <asm/hardware/dec21285.h>
-#include <asm/leds.h>
 #include <asm/mach-types.h>
 #include <asm/setup.h>
 #include <asm/system_misc.h>
@@ -27,13 +28,6 @@
 #define GP1_IO_BASE		0x338
 #define GP2_IO_BASE		0x33a
 
-
-#ifdef CONFIG_LEDS
-#define DEFAULT_LEDS	0
-#else
-#define DEFAULT_LEDS	GPIO_GREEN_LED
-#endif
-
 /*
  * Winbond WB83977F accessibility stuff
  */
@@ -611,15 +605,9 @@ static void __init rwa010_init(void)
 static int __init nw_hw_init(void)
 {
 	if (machine_is_netwinder()) {
-		unsigned long flags;
-
 		wb977_init();
 		cpld_init();
 		rwa010_init();
-
-		raw_spin_lock_irqsave(&nw_gpio_lock, flags);
-		nw_gpio_modify_op(GPIO_RED_LED|GPIO_GREEN_LED, DEFAULT_LEDS);
-		raw_spin_unlock_irqrestore(&nw_gpio_lock, flags);
 	}
 	return 0;
 }
@@ -672,6 +660,102 @@ static void netwinder_restart(char mode, const char *cmd)
 	}
 }
 
+/* LEDs */
+#if defined(CONFIG_NEW_LEDS) && defined(CONFIG_LEDS_CLASS)
+struct netwinder_led {
+	struct led_classdev     cdev;
+	u8                      mask;
+};
+
+/*
+ * The triggers lines up below will only be used if the
+ * LED triggers are compiled in.
+ */
+static const struct {
+	const char *name;
+	const char *trigger;
+} netwinder_leds[] = {
+	{ "netwinder:green", "heartbeat", },
+	{ "netwinder:red", "cpu0", },
+};
+
+/*
+ * The LED control in Netwinder is reversed:
+ *  - setting bit means turn off LED
+ *  - clearing bit means turn on LED
+ */
+static void netwinder_led_set(struct led_classdev *cdev,
+		enum led_brightness b)
+{
+	struct netwinder_led *led = container_of(cdev,
+			struct netwinder_led, cdev);
+	unsigned long flags;
+	u32 reg;
+
+	spin_lock_irqsave(&nw_gpio_lock, flags);
+	reg = nw_gpio_read();
+	if (b != LED_OFF)
+		reg &= ~led->mask;
+	else
+		reg |= led->mask;
+	nw_gpio_modify_op(led->mask, reg);
+	spin_unlock_irqrestore(&nw_gpio_lock, flags);
+}
+
+static enum led_brightness netwinder_led_get(struct led_classdev *cdev)
+{
+	struct netwinder_led *led = container_of(cdev,
+			struct netwinder_led, cdev);
+	unsigned long flags;
+	u32 reg;
+
+	spin_lock_irqsave(&nw_gpio_lock, flags);
+	reg = nw_gpio_read();
+	spin_unlock_irqrestore(&nw_gpio_lock, flags);
+
+	return (reg & led->mask) ? LED_OFF : LED_FULL;
+}
+
+static int __init netwinder_leds_init(void)
+{
+	int i;
+
+	if (!machine_is_netwinder())
+		return -ENODEV;
+
+	for (i = 0; i < ARRAY_SIZE(netwinder_leds); i++) {
+		struct netwinder_led *led;
+
+		led = kzalloc(sizeof(*led), GFP_KERNEL);
+		if (!led)
+			break;
+
+		led->cdev.name = netwinder_leds[i].name;
+		led->cdev.brightness_set = netwinder_led_set;
+		led->cdev.brightness_get = netwinder_led_get;
+		led->cdev.default_trigger = netwinder_leds[i].trigger;
+
+		if (i == 0)
+			led->mask = GPIO_GREEN_LED;
+		else
+			led->mask = GPIO_RED_LED;
+
+		if (led_classdev_register(NULL, &led->cdev) < 0) {
+			kfree(led);
+			break;
+		}
+	}
+
+	return 0;
+}
+
+/*
+ * Since we may have triggers on any subsystem, defer registration
+ * until after subsystem_init.
+ */
+fs_initcall(netwinder_leds_init);
+#endif
+
 MACHINE_START(NETWINDER, "Rebel-NetWinder")
 	/* Maintainer: Russell King/Rebel.com */
 	.atag_offset	= 0x100,

arch/arm/mach-footbridge/netwinder-leds.c

@@ -1,138 +0,0 @@
-/*
- *  linux/arch/arm/mach-footbridge/netwinder-leds.c
- *
- *  Copyright (C) 1998-1999 Russell King
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * NetWinder LED control routines.
- *
- * The Netwinder uses the leds as follows:
- *  - Green - toggles state every 50 timer interrupts
- *  - Red   - On if the system is not idle
- *
- * Changelog:
- *   02-05-1999	RMK	Various cleanups
- */
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/spinlock.h>
-
-#include <mach/hardware.h>
-#include <asm/leds.h>
-#include <asm/mach-types.h>
-
-#define LED_STATE_ENABLED	1
-#define LED_STATE_CLAIMED	2
-static char led_state;
-static char hw_led_state;
-
-static DEFINE_RAW_SPINLOCK(leds_lock);
-
-static void netwinder_leds_event(led_event_t evt)
-{
-	unsigned long flags;
-
-	raw_spin_lock_irqsave(&leds_lock, flags);
-
-	switch (evt) {
-	case led_start:
-		led_state |= LED_STATE_ENABLED;
-		hw_led_state = GPIO_GREEN_LED;
-		break;
-
-	case led_stop:
-		led_state &= ~LED_STATE_ENABLED;
-		break;
-
-	case led_claim:
-		led_state |= LED_STATE_CLAIMED;
-		hw_led_state = 0;
-		break;
-
-	case led_release:
-		led_state &= ~LED_STATE_CLAIMED;
-		hw_led_state = 0;
-		break;
-
-#ifdef CONFIG_LEDS_TIMER
-	case led_timer:
-		if (!(led_state & LED_STATE_CLAIMED))
-			hw_led_state ^= GPIO_GREEN_LED;
-		break;
-#endif
-
-#ifdef CONFIG_LEDS_CPU
-	case led_idle_start:
-		if (!(led_state & LED_STATE_CLAIMED))
-			hw_led_state &= ~GPIO_RED_LED;
-		break;
-
-	case led_idle_end:
-		if (!(led_state & LED_STATE_CLAIMED))
-			hw_led_state |= GPIO_RED_LED;
-		break;
-#endif
-
-	case led_halted:
-		if (!(led_state & LED_STATE_CLAIMED))
-			hw_led_state |= GPIO_RED_LED;
-		break;
-
-	case led_green_on:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state |= GPIO_GREEN_LED;
-		break;
-
-	case led_green_off:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state &= ~GPIO_GREEN_LED;
-		break;
-
-	case led_amber_on:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state |= GPIO_GREEN_LED | GPIO_RED_LED;
-		break;
-
-	case led_amber_off:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state &= ~(GPIO_GREEN_LED | GPIO_RED_LED);
-		break;
-
-	case led_red_on:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state |= GPIO_RED_LED;
-		break;
-
-	case led_red_off:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state &= ~GPIO_RED_LED;
-		break;
-
-	default:
-		break;
-	}
-
-	raw_spin_unlock_irqrestore(&leds_lock, flags);
-
-	if  (led_state & LED_STATE_ENABLED) {
-		raw_spin_lock_irqsave(&nw_gpio_lock, flags);
-		nw_gpio_modify_op(GPIO_RED_LED | GPIO_GREEN_LED, hw_led_state);
-		raw_spin_unlock_irqrestore(&nw_gpio_lock, flags);
-	}
-}
-
-static int __init leds_init(void)
-{
-	if (machine_is_netwinder())
-		leds_event = netwinder_leds_event;
-
-	leds_event(led_start);
-
-	return 0;
-}
-
-__initcall(leds_init);

arch/arm/mach-integrator/Makefile

@@ -4,11 +4,10 @@
 
 # Object file lists.
 
-obj-y					:= core.o lm.o
+obj-y					:= core.o lm.o leds.o
 obj-$(CONFIG_ARCH_INTEGRATOR_AP)	+= integrator_ap.o
 obj-$(CONFIG_ARCH_INTEGRATOR_CP)	+= integrator_cp.o
 
-obj-$(CONFIG_LEDS)			+= leds.o
 obj-$(CONFIG_PCI)			+= pci_v3.o pci.o
 obj-$(CONFIG_CPU_FREQ_INTEGRATOR)	+= cpu.o
 obj-$(CONFIG_INTEGRATOR_IMPD1)		+= impd1.o

arch/arm/mach-integrator/core.c

@@ -28,7 +28,6 @@
 #include <mach/cm.h>
 #include <mach/irqs.h>
 
-#include <asm/leds.h>
 #include <asm/mach-types.h>
 #include <asm/mach/time.h>
 #include <asm/pgtable.h>
@@ -128,8 +127,6 @@ static struct amba_pl010_data integrator_uart_data = {
 	.set_mctrl = integrator_uart_set_mctrl,
 };
 
-#define CM_CTRL	IO_ADDRESS(INTEGRATOR_HDR_CTRL)
-
 static DEFINE_RAW_SPINLOCK(cm_lock);
 
 /**

arch/arm/mach-integrator/include/mach/cm.h

@@ -3,6 +3,8 @@
  */
 void cm_control(u32, u32);
 
+#define CM_CTRL	IO_ADDRESS(INTEGRATOR_HDR_CTRL)
+
 #define CM_CTRL_LED			(1 << 0)
 #define CM_CTRL_nMBDET			(1 << 1)
 #define CM_CTRL_REMAP			(1 << 2)

arch/arm/mach-integrator/leds.c

@@ -1,90 +1,125 @@
 /*
- *  linux/arch/arm/mach-integrator/leds.c
+ * Driver for the 4 user LEDs found on the Integrator AP/CP baseboard
+ * Based on Versatile and RealView machine LED code
  *
- *  Integrator/AP and Integrator/CP LED control routines
- *
- *  Copyright (C) 1999 ARM Limited
- *  Copyright (C) 2000 Deep Blue Solutions Ltd
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ * License terms: GNU General Public License (GPL) version 2
+ * Author: Bryan Wu <bryan.wu@canonical.com>
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
-#include <linux/smp.h>
-#include <linux/spinlock.h>
 #include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/leds.h>
 
+#include <mach/cm.h>
 #include <mach/hardware.h>
 #include <mach/platform.h>
-#include <asm/leds.h>
-#include <asm/mach-types.h>
-#include <mach/cm.h>
 
-static int saved_leds;
+#if defined(CONFIG_NEW_LEDS) && defined(CONFIG_LEDS_CLASS)
+
+#define ALPHA_REG __io_address(INTEGRATOR_DBG_BASE)
+#define LEDREG	(__io_address(INTEGRATOR_DBG_BASE) + INTEGRATOR_DBG_LEDS_OFFSET)
 
-static void integrator_leds_event(led_event_t ledevt)
+struct integrator_led {
+	struct led_classdev	cdev;
+	u8			mask;
+};
+
+/*
+ * The triggers lines up below will only be used if the
+ * LED triggers are compiled in.
+ */
+static const struct {
+	const char *name;
+	const char *trigger;
+} integrator_leds[] = {
+	{ "integrator:green0", "heartbeat", },
+	{ "integrator:yellow", },
+	{ "integrator:red", },
+	{ "integrator:green1", },
+	{ "integrator:core_module", "cpu0", },
+};
+
+static void integrator_led_set(struct led_classdev *cdev,
+			      enum led_brightness b)
 {
-	unsigned long flags;
-	const unsigned int dbg_base = IO_ADDRESS(INTEGRATOR_DBG_BASE);
-	unsigned int update_alpha_leds;
+	struct integrator_led *led = container_of(cdev,
+						 struct integrator_led, cdev);
+	u32 reg = __raw_readl(LEDREG);
 
-	// yup, change the LEDs
-	local_irq_save(flags);
-	update_alpha_leds = 0;
+	if (b != LED_OFF)
+		reg |= led->mask;
+	else
+		reg &= ~led->mask;
 
-	switch(ledevt) {
-	case led_idle_start:
-		cm_control(CM_CTRL_LED, 0);
-		break;
+	while (__raw_readl(ALPHA_REG) & 1)
+		cpu_relax();
 
-	case led_idle_end:
-		cm_control(CM_CTRL_LED, CM_CTRL_LED);
-		break;
+	__raw_writel(reg, LEDREG);
+}
 
-	case led_timer:
-		saved_leds ^= GREEN_LED;
-		update_alpha_leds = 1;
-		break;
+static enum led_brightness integrator_led_get(struct led_classdev *cdev)
+{
+	struct integrator_led *led = container_of(cdev,
+						 struct integrator_led, cdev);
+	u32 reg = __raw_readl(LEDREG);
 
-	case led_red_on:
-		saved_leds |= RED_LED;
-		update_alpha_leds = 1;
-		break;
+	return (reg & led->mask) ? LED_FULL : LED_OFF;
+}
 
-	case led_red_off:
-		saved_leds &= ~RED_LED;
-		update_alpha_leds = 1;
-		break;
+static void cm_led_set(struct led_classdev *cdev,
+			      enum led_brightness b)
+{
+	if (b != LED_OFF)
+		cm_control(CM_CTRL_LED, CM_CTRL_LED);
+	else
+		cm_control(CM_CTRL_LED, 0);
+}
 
-	default:
-		break;
-	}
+static enum led_brightness cm_led_get(struct led_classdev *cdev)
+{
+	u32 reg = readl(CM_CTRL);
 
-	if (update_alpha_leds) {
-		while (__raw_readl(dbg_base + INTEGRATOR_DBG_ALPHA_OFFSET) & 1);
-		__raw_writel(saved_leds, dbg_base + INTEGRATOR_DBG_LEDS_OFFSET);
-	}
-	local_irq_restore(flags);
+	return (reg & CM_CTRL_LED) ? LED_FULL : LED_OFF;
 }
 
-static int __init leds_init(void)
+static int __init integrator_leds_init(void)
 {
-	if (machine_is_integrator() || machine_is_cintegrator())
-		leds_event = integrator_leds_event;
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(integrator_leds); i++) {
+		struct integrator_led *led;
+
+		led = kzalloc(sizeof(*led), GFP_KERNEL);
+		if (!led)
+			break;
+
+
+		led->cdev.name = integrator_leds[i].name;
+
+		if (i == 4) { /* Setting for LED in core module */
+			led->cdev.brightness_set = cm_led_set;
+			led->cdev.brightness_get = cm_led_get;
+		} else {
+			led->cdev.brightness_set = integrator_led_set;
+			led->cdev.brightness_get = integrator_led_get;
+		}
+
+		led->cdev.default_trigger = integrator_leds[i].trigger;
+		led->mask = BIT(i);
+
+		if (led_classdev_register(NULL, &led->cdev) < 0) {
+			kfree(led);
+			break;
+		}
+	}
 
 	return 0;
 }
 
-core_initcall(leds_init);
+/*
+ * Since we may have triggers on any subsystem, defer registration
+ * until after subsystem_init.
+ */
+fs_initcall(integrator_leds_init);
+#endif

arch/arm/mach-ks8695/Makefile

@@ -11,9 +11,6 @@ obj-				:=
 # PCI support is optional
 obj-$(CONFIG_PCI)		+= pci.o
 
-# LEDs
-obj-$(CONFIG_LEDS)		+= leds.o
-
 # Board-specific support
 obj-$(CONFIG_MACH_KS8695)	+= board-micrel.o
 obj-$(CONFIG_MACH_DSM320)	+= board-dsm320.o

arch/arm/mach-ks8695/devices.c

@@ -182,27 +182,6 @@ static void __init ks8695_add_device_watchdog(void)
 }
 
 
-/* --------------------------------------------------------------------
- *  LEDs
- * -------------------------------------------------------------------- */
-
-#if defined(CONFIG_LEDS)
-short ks8695_leds_cpu = -1;
-short ks8695_leds_timer = -1;
-
-void __init ks8695_init_leds(u8 cpu_led, u8 timer_led)
-{
-	/* Enable GPIO to access the LEDs */
-	gpio_direction_output(cpu_led, 1);
-	gpio_direction_output(timer_led, 1);
-
-	ks8695_leds_cpu	  = cpu_led;
-	ks8695_leds_timer = timer_led;
-}
-#else
-void __init ks8695_init_leds(u8 cpu_led, u8 timer_led) {}
-#endif
-
 /* -------------------------------------------------------------------- */
 
 /*

arch/arm/mach-ks8695/include/mach/devices.h

@@ -18,11 +18,6 @@ extern void __init ks8695_add_device_wan(void);
 extern void __init ks8695_add_device_lan(void);
 extern void __init ks8695_add_device_hpna(void);
 
- /* LEDs */
-extern short ks8695_leds_cpu;
-extern short ks8695_leds_timer;
-extern void __init ks8695_init_leds(u8 cpu_led, u8 timer_led);
-
  /* PCI */
 #define KS8695_MODE_PCI		0
 #define KS8695_MODE_MINIPCI	1

arch/arm/mach-ks8695/leds.c

@@ -1,92 +0,0 @@
-/*
- * LED driver for KS8695-based boards.
- *
- * Copyright (C) Andrew Victor
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/init.h>
-
-#include <asm/leds.h>
-#include <mach/devices.h>
-
-
-static inline void ks8695_led_on(unsigned int led)
-{
-	gpio_set_value(led, 0);
-}
-
-static inline void ks8695_led_off(unsigned int led)
-{
-	gpio_set_value(led, 1);
-}
-
-static inline void ks8695_led_toggle(unsigned int led)
-{
-	unsigned long is_off = gpio_get_value(led);
-	if (is_off)
-		ks8695_led_on(led);
-	else
-		ks8695_led_off(led);
-}
-
-
-/*
- * Handle LED events.
- */
-static void ks8695_leds_event(led_event_t evt)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-
-	switch(evt) {
-	case led_start:		/* System startup */
-		ks8695_led_on(ks8695_leds_cpu);
-		break;
-
-	case led_stop:		/* System stop / suspend */
-		ks8695_led_off(ks8695_leds_cpu);
-		break;
-
-#ifdef CONFIG_LEDS_TIMER
-	case led_timer:		/* Every 50 timer ticks */
-		ks8695_led_toggle(ks8695_leds_timer);
-		break;
-#endif
-
-#ifdef CONFIG_LEDS_CPU
-	case led_idle_start:	/* Entering idle state */
-		ks8695_led_off(ks8695_leds_cpu);
-		break;
-
-	case led_idle_end:	/* Exit idle state */
-		ks8695_led_on(ks8695_leds_cpu);
-		break;
-#endif
-
-	default:
-		break;
-	}
-
-	local_irq_restore(flags);
-}
-
-
-static int __init leds_init(void)
-{
-	if ((ks8695_leds_timer == -1) || (ks8695_leds_cpu == -1))
-		return -ENODEV;
-
-	leds_event = ks8695_leds_event;
-
-	leds_event(led_start);
-	return 0;
-}
-
-__initcall(leds_init);

arch/arm/mach-omap1/Makefile

@@ -61,14 +61,6 @@ obj-$(CONFIG_ARCH_OMAP850)		+= gpio7xx.o
 obj-$(CONFIG_ARCH_OMAP15XX)		+= gpio15xx.o
 obj-$(CONFIG_ARCH_OMAP16XX)		+= gpio16xx.o
 
-# LEDs support
-led-$(CONFIG_MACH_OMAP_H2)		+= leds-h2p2-debug.o
-led-$(CONFIG_MACH_OMAP_H3)		+= leds-h2p2-debug.o
-led-$(CONFIG_MACH_OMAP_INNOVATOR)	+= leds-innovator.o
-led-$(CONFIG_MACH_OMAP_PERSEUS2)	+= leds-h2p2-debug.o
-led-$(CONFIG_MACH_OMAP_OSK)		+= leds-osk.o
-obj-$(CONFIG_LEDS)			+= $(led-y)
-
 ifneq ($(CONFIG_FB_OMAP),)
 obj-y += lcd_dma.o
 endif

arch/arm/mach-omap1/board-h2.c

@@ -32,6 +32,7 @@
 #include <linux/smc91x.h>
 #include <linux/omapfb.h>
 #include <linux/platform_data/gpio-omap.h>
+#include <linux/leds.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -307,12 +308,39 @@ static struct platform_device h2_irda_device = {
 	.resource	= h2_irda_resources,
 };
 
+static struct gpio_led h2_gpio_led_pins[] = {
+	{
+		.name		= "h2:red",
+		.default_trigger = "heartbeat",
+		.gpio		= 3,
+	},
+	{
+		.name		= "h2:green",
+		.default_trigger = "cpu0",
+		.gpio		= OMAP_MPUIO(4),
+	},
+};
+
+static struct gpio_led_platform_data h2_gpio_led_data = {
+	.leds		= h2_gpio_led_pins,
+	.num_leds	= ARRAY_SIZE(h2_gpio_led_pins),
+};
+
+static struct platform_device h2_gpio_leds = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data = &h2_gpio_led_data,
+	},
+};
+
 static struct platform_device *h2_devices[] __initdata = {
 	&h2_nor_device,
 	&h2_nand_device,
 	&h2_smc91x_device,
 	&h2_irda_device,
 	&h2_kp_device,
+	&h2_gpio_leds,
 };
 
 static void __init h2_init_smc91x(void)
@@ -407,6 +435,10 @@ static void __init h2_init(void)
 	omap_cfg_reg(E19_1610_KBR4);
 	omap_cfg_reg(N19_1610_KBR5);
 
+	/* GPIO based LEDs */
+	omap_cfg_reg(P18_1610_GPIO3);
+	omap_cfg_reg(MPUIO4);
+
 	h2_smc91x_resources[1].start = gpio_to_irq(0);
 	h2_smc91x_resources[1].end = gpio_to_irq(0);
 	platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));

arch/arm/mach-omap1/board-h3.c

@@ -32,6 +32,7 @@
 #include <linux/smc91x.h>
 #include <linux/omapfb.h>
 #include <linux/platform_data/gpio-omap.h>
+#include <linux/leds.h>
 
 #include <asm/setup.h>
 #include <asm/page.h>
@@ -325,6 +326,32 @@ static struct spi_board_info h3_spi_board_info[] __initdata = {
 	},
 };
 
+static struct gpio_led h3_gpio_led_pins[] = {
+	{
+		.name		= "h3:red",
+		.default_trigger = "heartbeat",
+		.gpio		= 3,
+	},
+	{
+		.name		= "h3:green",
+		.default_trigger = "cpu0",
+		.gpio		= OMAP_MPUIO(4),
+	},
+};
+
+static struct gpio_led_platform_data h3_gpio_led_data = {
+	.leds		= h3_gpio_led_pins,
+	.num_leds	= ARRAY_SIZE(h3_gpio_led_pins),
+};
+
+static struct platform_device h3_gpio_leds = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data = &h3_gpio_led_data,
+	},
+};
+
 static struct platform_device *devices[] __initdata = {
 	&nor_device,
 	&nand_device,
@@ -332,6 +359,7 @@ static struct platform_device *devices[] __initdata = {
 	&intlat_device,
 	&h3_kp_device,
 	&h3_lcd_device,
+	&h3_gpio_leds,
 };
 
 static struct omap_usb_config h3_usb_config __initdata = {
@@ -399,6 +427,10 @@ static void __init h3_init(void)
 	omap_cfg_reg(E19_1610_KBR4);
 	omap_cfg_reg(N19_1610_KBR5);
 
+	/* GPIO based LEDs */
+	omap_cfg_reg(P18_1610_GPIO3);
+	omap_cfg_reg(MPUIO4);
+
 	smc91x_resources[1].start = gpio_to_irq(40);
 	smc91x_resources[1].end = gpio_to_irq(40);
 	platform_add_devices(devices, ARRAY_SIZE(devices));

arch/arm/mach-omap1/board-osk.c

@@ -382,10 +382,37 @@ static struct platform_device osk5912_lcd_device = {
 	.id		= -1,
 };
 
+static struct gpio_led mistral_gpio_led_pins[] = {
+	{
+		.name		= "mistral:red",
+		.default_trigger = "heartbeat",
+		.gpio		= 3,
+	},
+	{
+		.name		= "mistral:green",
+		.default_trigger = "cpu0",
+		.gpio		= OMAP_MPUIO(4),
+	},
+};
+
+static struct gpio_led_platform_data mistral_gpio_led_data = {
+	.leds		= mistral_gpio_led_pins,
+	.num_leds	= ARRAY_SIZE(mistral_gpio_led_pins),
+};
+
+static struct platform_device mistral_gpio_leds = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data = &mistral_gpio_led_data,
+	},
+};
+
 static struct platform_device *mistral_devices[] __initdata = {
 	&osk5912_kp_device,
 	&mistral_bl_device,
 	&osk5912_lcd_device,
+	&mistral_gpio_leds,
 };
 
 static int mistral_get_pendown_state(void)
@@ -510,6 +537,12 @@ static void __init osk_mistral_init(void)
 	if (gpio_request(2, "lcd_pwr") == 0)
 		gpio_direction_output(2, 1);
 
+	/*
+	 * GPIO based LEDs
+	 */
+	omap_cfg_reg(P18_1610_GPIO3);
+	omap_cfg_reg(MPUIO4);
+
 	i2c_register_board_info(1, mistral_i2c_board_info,
 			ARRAY_SIZE(mistral_i2c_board_info));
 

arch/arm/mach-omap1/leds-h2p2-debug.c

@@ -1,169 +0,0 @@
-/*
- * linux/arch/arm/mach-omap1/leds-h2p2-debug.c
- *
- * Copyright 2003 by Texas Instruments Incorporated
- *
- * There are 16 LEDs on the debug board (all green); four may be used
- * for logical 'green', 'amber', 'red', and 'blue' (after "claiming").
- *
- * The "surfer" expansion board and H2 sample board also have two-color
- * green+red LEDs (in parallel), used here for timer and idle indicators.
- */
-#include <linux/gpio.h>
-#include <linux/init.h>
-#include <linux/kernel_stat.h>
-#include <linux/sched.h>
-#include <linux/io.h>
-#include <linux/platform_data/gpio-omap.h>
-
-#include <mach/hardware.h>
-#include <asm/leds.h>
-#include <asm/mach-types.h>
-
-#include <plat/fpga.h>
-
-#include "leds.h"
-
-
-#define GPIO_LED_RED		3
-#define GPIO_LED_GREEN		OMAP_MPUIO(4)
-
-
-#define LED_STATE_ENABLED	0x01
-#define LED_STATE_CLAIMED	0x02
-#define LED_TIMER_ON		0x04
-
-#define GPIO_IDLE		GPIO_LED_GREEN
-#define GPIO_TIMER		GPIO_LED_RED
-
-
-void h2p2_dbg_leds_event(led_event_t evt)
-{
-	unsigned long flags;
-
-	static struct h2p2_dbg_fpga __iomem *fpga;
-	static u16 led_state, hw_led_state;
-
-	local_irq_save(flags);
-
-	if (!(led_state & LED_STATE_ENABLED) && evt != led_start)
-		goto done;
-
-	switch (evt) {
-	case led_start:
-		if (!fpga)
-			fpga = ioremap(H2P2_DBG_FPGA_START,
-						H2P2_DBG_FPGA_SIZE);
-		if (fpga) {
-			led_state |= LED_STATE_ENABLED;
-			__raw_writew(~0, &fpga->leds);
-		}
-		break;
-
-	case led_stop:
-	case led_halted:
-		/* all leds off during suspend or shutdown */
-
-		if (! machine_is_omap_perseus2()) {
-			gpio_set_value(GPIO_TIMER, 0);
-			gpio_set_value(GPIO_IDLE, 0);
-		}
-
-		led_state &= ~LED_STATE_ENABLED;
-		if (fpga) {
-			__raw_writew(~0, &fpga->leds);
-			if (evt == led_halted) {
-				iounmap(fpga);
-				fpga = NULL;
-			}
-		}
-
-		goto done;
-
-	case led_claim:
-		led_state |= LED_STATE_CLAIMED;
-		hw_led_state = 0;
-		break;
-
-	case led_release:
-		led_state &= ~LED_STATE_CLAIMED;
-		break;
-
-#ifdef CONFIG_LEDS_TIMER
-	case led_timer:
-		led_state ^= LED_TIMER_ON;
-
-		if (machine_is_omap_perseus2())
-			hw_led_state ^= H2P2_DBG_FPGA_P2_LED_TIMER;
-		else {
-			gpio_set_value(GPIO_TIMER, led_state & LED_TIMER_ON);
-			goto done;
-		}
-
-		break;
-#endif
-
-#ifdef CONFIG_LEDS_CPU
-	case led_idle_start:
-		if (machine_is_omap_perseus2())
-			hw_led_state |= H2P2_DBG_FPGA_P2_LED_IDLE;
-		else {
-			gpio_set_value(GPIO_IDLE, 1);
-			goto done;
-		}
-
-		break;
-
-	case led_idle_end:
-		if (machine_is_omap_perseus2())
-			hw_led_state &= ~H2P2_DBG_FPGA_P2_LED_IDLE;
-		else {
-			gpio_set_value(GPIO_IDLE, 0);
-			goto done;
-		}
-
-		break;
-#endif
-
-	case led_green_on:
-		hw_led_state |= H2P2_DBG_FPGA_LED_GREEN;
-		break;
-	case led_green_off:
-		hw_led_state &= ~H2P2_DBG_FPGA_LED_GREEN;
-		break;
-
-	case led_amber_on:
-		hw_led_state |= H2P2_DBG_FPGA_LED_AMBER;
-		break;
-	case led_amber_off:
-		hw_led_state &= ~H2P2_DBG_FPGA_LED_AMBER;
-		break;
-
-	case led_red_on:
-		hw_led_state |= H2P2_DBG_FPGA_LED_RED;
-		break;
-	case led_red_off:
-		hw_led_state &= ~H2P2_DBG_FPGA_LED_RED;
-		break;
-
-	case led_blue_on:
-		hw_led_state |= H2P2_DBG_FPGA_LED_BLUE;
-		break;
-	case led_blue_off:
-		hw_led_state &= ~H2P2_DBG_FPGA_LED_BLUE;
-		break;
-
-	default:
-		break;
-	}
-
-
-	/*
-	 *  Actually burn the LEDs
-	 */
-	if (led_state & LED_STATE_ENABLED && fpga)
-		__raw_writew(~hw_led_state, &fpga->leds);
-
-done:
-	local_irq_restore(flags);
-}

arch/arm/mach-omap1/leds-innovator.c

@@ -1,98 +0,0 @@
-/*
- * linux/arch/arm/mach-omap1/leds-innovator.c
- */
-#include <linux/init.h>
-
-#include <mach/hardware.h>
-#include <asm/leds.h>
-
-#include "leds.h"
-
-
-#define LED_STATE_ENABLED	1
-#define LED_STATE_CLAIMED	2
-
-static unsigned int led_state;
-static unsigned int hw_led_state;
-
-void innovator_leds_event(led_event_t evt)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-
-	switch (evt) {
-	case led_start:
-		hw_led_state = 0;
-		led_state = LED_STATE_ENABLED;
-		break;
-
-	case led_stop:
-		led_state &= ~LED_STATE_ENABLED;
-		hw_led_state = 0;
-		break;
-
-	case led_claim:
-		led_state |= LED_STATE_CLAIMED;
-		hw_led_state = 0;
-		break;
-
-	case led_release:
-		led_state &= ~LED_STATE_CLAIMED;
-		hw_led_state = 0;
-		break;
-
-#ifdef CONFIG_LEDS_TIMER
-	case led_timer:
-		if (!(led_state & LED_STATE_CLAIMED))
-			hw_led_state ^= 0;
-		break;
-#endif
-
-#ifdef CONFIG_LEDS_CPU
-	case led_idle_start:
-		if (!(led_state & LED_STATE_CLAIMED))
-			hw_led_state |= 0;
-		break;
-
-	case led_idle_end:
-		if (!(led_state & LED_STATE_CLAIMED))
-			hw_led_state &= ~0;
-		break;
-#endif
-
-	case led_halted:
-		break;
-
-	case led_green_on:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state &= ~0;
-		break;
-
-	case led_green_off:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state |= 0;
-		break;
-
-	case led_amber_on:
-		break;
-
-	case led_amber_off:
-		break;
-
-	case led_red_on:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state &= ~0;
-		break;
-
-	case led_red_off:
-		if (led_state & LED_STATE_CLAIMED)
-			hw_led_state |= 0;
-		break;
-
-	default:
-		break;
-	}
-
-	local_irq_restore(flags);
-}

arch/arm/mach-omap1/leds-osk.c

@@ -1,113 +0,0 @@
-/*
- * linux/arch/arm/mach-omap1/leds-osk.c
- *
- * LED driver for OSK with optional Mistral QVGA board
- */
-#include <linux/gpio.h>
-#include <linux/init.h>
-
-#include <mach/hardware.h>
-#include <asm/leds.h>
-
-#include "leds.h"
-
-
-#define LED_STATE_ENABLED	(1 << 0)
-#define LED_STATE_CLAIMED	(1 << 1)
-static u8 led_state;
-
-#define	TIMER_LED		(1 << 3)	/* Mistral board */
-#define	IDLE_LED		(1 << 4)	/* Mistral board */
-static u8 hw_led_state;
-
-
-#ifdef	CONFIG_OMAP_OSK_MISTRAL
-
-/* For now, all system indicators require the Mistral board, since that
- * LED can be manipulated without a task context.  This LED is either red,
- * or green, but not both; it can't give the full "disco led" effect.
- */
-
-#define GPIO_LED_RED		3
-#define GPIO_LED_GREEN		OMAP_MPUIO(4)
-
-static void mistral_setled(void)
-{
-	int	red = 0;
-	int	green = 0;
-
-	if (hw_led_state & TIMER_LED)
-		red = 1;
-	else if (hw_led_state & IDLE_LED)
-		green = 1;
-	/* else both sides are disabled */
-
-	gpio_set_value(GPIO_LED_GREEN, green);
-	gpio_set_value(GPIO_LED_RED, red);
-}
-
-#endif
-
-void osk_leds_event(led_event_t evt)
-{
-	unsigned long	flags;
-	u16		leds;
-
-	local_irq_save(flags);
-
-	if (!(led_state & LED_STATE_ENABLED) && evt != led_start)
-		goto done;
-
-	leds = hw_led_state;
-	switch (evt) {
-	case led_start:
-		led_state |= LED_STATE_ENABLED;
-		hw_led_state = 0;
-		leds = ~0;
-		break;
-
-	case led_halted:
-	case led_stop:
-		led_state &= ~LED_STATE_ENABLED;
-		hw_led_state = 0;
-		break;
-
-	case led_claim:
-		led_state |= LED_STATE_CLAIMED;
-		hw_led_state = 0;
-		leds = ~0;
-		break;
-
-	case led_release:
-		led_state &= ~LED_STATE_CLAIMED;
-		hw_led_state = 0;
-		break;
-
-#ifdef	CONFIG_OMAP_OSK_MISTRAL
-
-	case led_timer:
-		hw_led_state ^= TIMER_LED;
-		mistral_setled();
-		break;
-
-	case led_idle_start:	/* idle == off */
-		hw_led_state &= ~IDLE_LED;
-		mistral_setled();
-		break;
-
-	case led_idle_end:
-		hw_led_state |= IDLE_LED;
-		mistral_setled();
-		break;
-
-#endif	/* CONFIG_OMAP_OSK_MISTRAL */
-
-	default:
-		break;
-	}
-
-	leds ^= hw_led_state;
-
-done:
-	local_irq_restore(flags);
-}

arch/arm/mach-omap1/leds.c

@@ -1,70 +0,0 @@
-/*
- * linux/arch/arm/mach-omap1/leds.c
- *
- * OMAP LEDs dispatcher
- */
-#include <linux/gpio.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_data/gpio-omap.h>
-
-#include <asm/leds.h>
-#include <asm/mach-types.h>
-
-#include <mach/mux.h>
-
-#include "leds.h"
-
-static int __init
-omap_leds_init(void)
-{
-	if (!cpu_class_is_omap1())
-		return -ENODEV;
-
-	if (machine_is_omap_innovator())
-		leds_event = innovator_leds_event;
-
-	else if (machine_is_omap_h2()
-			|| machine_is_omap_h3()
-			|| machine_is_omap_perseus2())
-		leds_event = h2p2_dbg_leds_event;
-
-	else if (machine_is_omap_osk())
-		leds_event = osk_leds_event;
-
-	else
-		return -1;
-
-	if (machine_is_omap_h2()
-			|| machine_is_omap_h3()
-#ifdef	CONFIG_OMAP_OSK_MISTRAL
-			|| machine_is_omap_osk()
-#endif
-			) {
-
-		/* LED1/LED2 pins can be used as GPIO (as done here), or by
-		 * the LPG (works even in deep sleep!), to drive a bicolor
-		 * LED on the H2 sample board, and another on the H2/P2
-		 * "surfer" expansion board.
-		 *
-		 * The same pins drive a LED on the OSK Mistral board, but
-		 * that's a different kind of LED (just one color at a time).
-		 */
-		omap_cfg_reg(P18_1610_GPIO3);
-		if (gpio_request(3, "LED red") == 0)
-			gpio_direction_output(3, 1);
-		else
-			printk(KERN_WARNING "LED: can't get GPIO3/red?\n");
-
-		omap_cfg_reg(MPUIO4);
-		if (gpio_request(OMAP_MPUIO(4), "LED green") == 0)
-			gpio_direction_output(OMAP_MPUIO(4), 1);
-		else
-			printk(KERN_WARNING "LED: can't get MPUIO4/green?\n");
-	}
-
-	leds_event(led_start);
-	return 0;
-}
-
-__initcall(omap_leds_init);

arch/arm/mach-omap1/leds.h

@@ -1,3 +0,0 @@
-extern void innovator_leds_event(led_event_t evt);
-extern void h2p2_dbg_leds_event(led_event_t evt);
-extern void osk_leds_event(led_event_t evt);

arch/arm/mach-omap1/time.c

@@ -44,7 +44,6 @@
 #include <linux/clockchips.h>
 #include <linux/io.h>
 
-#include <asm/leds.h>
 #include <asm/irq.h>
 #include <asm/sched_clock.h>
 

arch/arm/mach-omap1/timer32k.c

@@ -46,7 +46,6 @@
 #include <linux/clockchips.h>
 #include <linux/io.h>
 
-#include <asm/leds.h>
 #include <asm/irq.h>
 #include <asm/mach/irq.h>
 #include <asm/mach/time.h>

arch/arm/mach-omap2/Kconfig

@@ -48,6 +48,7 @@ config ARCH_OMAP3
 	select ARM_CPU_SUSPEND if PM
 	select MULTI_IRQ_HANDLER
 	select SOC_HAS_OMAP2_SDRC
+	select OMAP_INTERCONNECT
 
 config ARCH_OMAP4
 	bool "TI OMAP4"
@@ -67,6 +68,7 @@ config ARCH_OMAP4
 	select USB_ARCH_HAS_EHCI if USB_SUPPORT
 	select ARM_CPU_SUSPEND if PM
 	select ARCH_NEEDS_CPU_IDLE_COUPLED if SMP
+	select OMAP_INTERCONNECT
 
 config SOC_OMAP5
 	bool "TI OMAP5"

arch/arm/mach-omap2/Makefile

@@ -180,11 +180,6 @@ obj-$(CONFIG_ARCH_OMAP4)		+= omap_hwmod_44xx_data.o
 # EMU peripherals
 obj-$(CONFIG_OMAP3_EMU)			+= emu.o
 
-# L3 interconnect
-obj-$(CONFIG_ARCH_OMAP3)		+= omap_l3_smx.o
-obj-$(CONFIG_ARCH_OMAP4)		+= omap_l3_noc.o
-obj-$(CONFIG_SOC_OMAP5)			+= omap_l3_noc.o
-
 obj-$(CONFIG_OMAP_MBOX_FWK)		+= mailbox_mach.o
 mailbox_mach-objs			:= mailbox.o
 

arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c

@@ -18,7 +18,6 @@
 #include <linux/ethtool.h>
 #include <net/dsa.h>
 #include <asm/mach-types.h>
-#include <asm/leds.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
 #include <mach/orion5x.h>

arch/arm/mach-orion5x/rd88f5181l-ge-setup.c

@@ -19,7 +19,6 @@
 #include <linux/i2c.h>
 #include <net/dsa.h>
 #include <asm/mach-types.h>
-#include <asm/leds.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
 #include <mach/orion5x.h>

arch/arm/mach-orion5x/rd88f5182-setup.c

@@ -19,8 +19,8 @@
 #include <linux/mv643xx_eth.h>
 #include <linux/ata_platform.h>
 #include <linux/i2c.h>
+#include <linux/leds.h>
 #include <asm/mach-types.h>
-#include <asm/leds.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
 #include <mach/orion5x.h>
@@ -53,12 +53,6 @@
 #define RD88F5182_PCI_SLOT0_IRQ_A_PIN	7
 #define RD88F5182_PCI_SLOT0_IRQ_B_PIN	6
 
-/*
- * GPIO Debug LED
- */
-
-#define RD88F5182_GPIO_DBG_LED		0
-
 /*****************************************************************************
  * 16M NOR Flash on Device bus CS1
  ****************************************************************************/
@@ -83,55 +77,32 @@ static struct platform_device rd88f5182_nor_flash = {
 	.resource		= &rd88f5182_nor_flash_resource,
 };
 
-#ifdef CONFIG_LEDS
-
 /*****************************************************************************
- * Use GPIO debug led as CPU active indication
+ * Use GPIO LED as CPU active indication
  ****************************************************************************/
 
-static void rd88f5182_dbgled_event(led_event_t evt)
-{
-	int val;
-
-	if (evt == led_idle_end)
-		val = 1;
-	else if (evt == led_idle_start)
-		val = 0;
-	else
-		return;
-
-	gpio_set_value(RD88F5182_GPIO_DBG_LED, val);
-}
-
-static int __init rd88f5182_dbgled_init(void)
-{
-	int pin;
-
-	if (machine_is_rd88f5182()) {
-		pin = RD88F5182_GPIO_DBG_LED;
+#define RD88F5182_GPIO_LED		0
 
-		if (gpio_request(pin, "DBGLED") == 0) {
-			if (gpio_direction_output(pin, 0) != 0) {
-				printk(KERN_ERR "rd88f5182_dbgled_init failed "
-						"to set output pin %d\n", pin);
-				gpio_free(pin);
-				return 0;
-			}
-		} else {
-			printk(KERN_ERR "rd88f5182_dbgled_init failed "
-					"to request gpio %d\n", pin);
-			return 0;
-		}
-
-		leds_event = rd88f5182_dbgled_event;
-	}
-
-	return 0;
-}
+static struct gpio_led rd88f5182_gpio_led_pins[] = {
+	{
+		.name		= "rd88f5182:cpu",
+		.default_trigger = "cpu0",
+		.gpio		= RD88F5182_GPIO_LED,
+	},
+};
 
-__initcall(rd88f5182_dbgled_init);
+static struct gpio_led_platform_data rd88f5182_gpio_led_data = {
+	.leds		= rd88f5182_gpio_led_pins,
+	.num_leds	= ARRAY_SIZE(rd88f5182_gpio_led_pins),
+};
 
-#endif
+static struct platform_device rd88f5182_gpio_leds = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data = &rd88f5182_gpio_led_data,
+	},
+};
 
 /*****************************************************************************
  * PCI
@@ -298,6 +269,7 @@ static void __init rd88f5182_init(void)
 
 	orion5x_setup_dev1_win(RD88F5182_NOR_BASE, RD88F5182_NOR_SIZE);
 	platform_device_register(&rd88f5182_nor_flash);
+	platform_device_register(&rd88f5182_gpio_leds);
 
 	i2c_register_board_info(0, &rd88f5182_i2c_rtc, 1);
 }

arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c

@@ -20,7 +20,6 @@
 #include <linux/ethtool.h>
 #include <net/dsa.h>
 #include <asm/mach-types.h>
-#include <asm/leds.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/pci.h>
 #include <mach/orion5x.h>

arch/arm/mach-pxa/Makefile

@@ -98,12 +98,4 @@ obj-$(CONFIG_MACH_RAUMFELD_CONNECTOR)	+= raumfeld.o
 obj-$(CONFIG_MACH_RAUMFELD_SPEAKER)	+= raumfeld.o
 obj-$(CONFIG_MACH_ZIPIT2)	+= z2.o
 
-# Support for blinky lights
-led-y := leds.o
-led-$(CONFIG_ARCH_LUBBOCK)	+= leds-lubbock.o
-led-$(CONFIG_MACH_MAINSTONE)	+= leds-mainstone.o
-led-$(CONFIG_ARCH_PXA_IDP)	+= leds-idp.o
-
-obj-$(CONFIG_LEDS)		+= $(led-y)
-
 obj-$(CONFIG_TOSA_BT)		+= tosa-bt.o