|
|
@@ -0,0 +1,655 @@
|
|
|
+/*
|
|
|
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
|
|
|
+ *
|
|
|
+ * This program is free software; you can redistribute it and/or modify
|
|
|
+ * it under the terms of the GNU General Public License version 2 as
|
|
|
+ * published by the Free Software Foundation.
|
|
|
+ */
|
|
|
+#include "omap5.dtsi"
|
|
|
+#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
+#include <dt-bindings/interrupt-controller/arm-gic.h>
|
|
|
+
|
|
|
+/ {
|
|
|
+ aliases {
|
|
|
+ display0 = &hdmi0;
|
|
|
+ };
|
|
|
+
|
|
|
+ vmmcsd_fixed: fixedregulator-mmcsd {
|
|
|
+ compatible = "regulator-fixed";
|
|
|
+ regulator-name = "vmmcsd_fixed";
|
|
|
+ regulator-min-microvolt = <3000000>;
|
|
|
+ regulator-max-microvolt = <3000000>;
|
|
|
+ };
|
|
|
+
|
|
|
+ mmc3_pwrseq: sdhci0_pwrseq {
|
|
|
+ compatible = "mmc-pwrseq-simple";
|
|
|
+ clocks = <&clk32kgaudio>;
|
|
|
+ clock-names = "ext_clock";
|
|
|
+ };
|
|
|
+
|
|
|
+ vmmcsdio_fixed: fixedregulator-mmcsdio {
|
|
|
+ compatible = "regulator-fixed";
|
|
|
+ regulator-name = "vmmcsdio_fixed";
|
|
|
+ regulator-min-microvolt = <1800000>;
|
|
|
+ regulator-max-microvolt = <1800000>;
|
|
|
+ gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>; /* gpio140 WLAN_EN */
|
|
|
+ enable-active-high;
|
|
|
+ startup-delay-us = <70000>;
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <&wlan_pins>;
|
|
|
+ };
|
|
|
+
|
|
|
+ /* HS USB Host PHY on PORT 2 */
|
|
|
+ hsusb2_phy: hsusb2_phy {
|
|
|
+ compatible = "usb-nop-xceiv";
|
|
|
+ reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
|
|
|
+ clocks = <&auxclk1_ck>;
|
|
|
+ clock-names = "main_clk";
|
|
|
+ clock-frequency = <19200000>;
|
|
|
+ };
|
|
|
+
|
|
|
+ /* HS USB Host PHY on PORT 3 */
|
|
|
+ hsusb3_phy: hsusb3_phy {
|
|
|
+ compatible = "usb-nop-xceiv";
|
|
|
+ reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
|
|
|
+ };
|
|
|
+
|
|
|
+ leds {
|
|
|
+ compatible = "gpio-leds";
|
|
|
+ led@1 {
|
|
|
+ label = "omap5:blue:usr1";
|
|
|
+ gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
|
|
|
+ linux,default-trigger = "heartbeat";
|
|
|
+ default-state = "off";
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ tpd12s015: encoder@0 {
|
|
|
+ compatible = "ti,tpd12s015";
|
|
|
+
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <&tpd12s015_pins>;
|
|
|
+
|
|
|
+ /* gpios defined in the board specific dts */
|
|
|
+
|
|
|
+ ports {
|
|
|
+ #address-cells = <1>;
|
|
|
+ #size-cells = <0>;
|
|
|
+
|
|
|
+ port@0 {
|
|
|
+ reg = <0>;
|
|
|
+
|
|
|
+ tpd12s015_in: endpoint@0 {
|
|
|
+ remote-endpoint = <&hdmi_out>;
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ port@1 {
|
|
|
+ reg = <1>;
|
|
|
+
|
|
|
+ tpd12s015_out: endpoint@0 {
|
|
|
+ remote-endpoint = <&hdmi_connector_in>;
|
|
|
+ };
|
|
|
+ };
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ hdmi0: connector@0 {
|
|
|
+ compatible = "hdmi-connector";
|
|
|
+ label = "hdmi";
|
|
|
+
|
|
|
+ type = "b";
|
|
|
+
|
|
|
+ port {
|
|
|
+ hdmi_connector_in: endpoint {
|
|
|
+ remote-endpoint = <&tpd12s015_out>;
|
|
|
+ };
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ sound: sound {
|
|
|
+ compatible = "ti,abe-twl6040";
|
|
|
+ ti,model = "omap5-uevm";
|
|
|
+
|
|
|
+ ti,mclk-freq = <19200000>;
|
|
|
+
|
|
|
+ ti,mcpdm = <&mcpdm>;
|
|
|
+
|
|
|
+ ti,twl6040 = <&twl6040>;
|
|
|
+
|
|
|
+ /* Audio routing */
|
|
|
+ ti,audio-routing =
|
|
|
+ "Headset Stereophone", "HSOL",
|
|
|
+ "Headset Stereophone", "HSOR",
|
|
|
+ "Line Out", "AUXL",
|
|
|
+ "Line Out", "AUXR",
|
|
|
+ "HSMIC", "Headset Mic",
|
|
|
+ "Headset Mic", "Headset Mic Bias",
|
|
|
+ "AFML", "Line In",
|
|
|
+ "AFMR", "Line In";
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+&omap5_pmx_core {
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <
|
|
|
+ &usbhost_pins
|
|
|
+ &led_gpio_pins
|
|
|
+ >;
|
|
|
+
|
|
|
+ twl6040_pins: pinmux_twl6040_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0x17e (PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ mcpdm_pins: pinmux_mcpdm_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
|
|
|
+ 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */
|
|
|
+ 0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */
|
|
|
+ 0x160 (PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */
|
|
|
+ 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ mcbsp1_pins: pinmux_mcbsp1_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */
|
|
|
+ 0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */
|
|
|
+ 0x150 (PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */
|
|
|
+ 0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ mcbsp2_pins: pinmux_mcbsp2_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */
|
|
|
+ 0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */
|
|
|
+ 0x158 (PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */
|
|
|
+ 0x15a (PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ i2c1_pins: pinmux_i2c1_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
|
|
|
+ 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ mcspi2_pins: pinmux_mcspi2_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
|
|
|
+ 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
|
|
|
+ 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */
|
|
|
+ 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ mcspi3_pins: pinmux_mcspi3_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi3_somi */
|
|
|
+ 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */
|
|
|
+ 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi3_simo */
|
|
|
+ 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi3_clk */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ mmc3_pins: pinmux_mmc3_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
|
|
|
+ OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
|
|
|
+ OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
|
|
|
+ OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
|
|
|
+ OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
|
|
|
+ OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ wlan_pins: pinmux_wlan_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ usbhost_pins: pinmux_usbhost_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0x84 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
|
|
|
+ 0x86 (PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
|
|
|
+
|
|
|
+ 0x19e (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
|
|
|
+ 0x1a0 (PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
|
|
|
+
|
|
|
+ 0x70 (PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */
|
|
|
+ 0x6e (PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ led_gpio_pins: pinmux_led_gpio_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0x196 (PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ uart1_pins: pinmux_uart1_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0x60 (PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */
|
|
|
+ 0x62 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */
|
|
|
+ 0x64 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */
|
|
|
+ 0x66 (PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ uart3_pins: pinmux_uart3_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0x19a (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */
|
|
|
+ 0x19c (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ uart5_pins: pinmux_uart5_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */
|
|
|
+ 0x172 (PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */
|
|
|
+ 0x174 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */
|
|
|
+ 0x176 (PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ dss_hdmi_pins: pinmux_dss_hdmi_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0x0fc (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */
|
|
|
+ 0x100 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */
|
|
|
+ 0x102 (PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ tpd12s015_pins: pinmux_tpd12s015_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0x0fe (PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+&omap5_pmx_wkup {
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <
|
|
|
+ &usbhost_wkup_pins
|
|
|
+ >;
|
|
|
+
|
|
|
+ usbhost_wkup_pins: pinmux_usbhost_wkup_pins {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ 0x1A (PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+
|
|
|
+ wlcore_irq_pin: pinmux_wlcore_irq_pin {
|
|
|
+ pinctrl-single,pins = <
|
|
|
+ OMAP5_IOPAD(0x040, WAKEUP_EN | PIN_INPUT_PULLUP | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */
|
|
|
+ >;
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+&mmc1 {
|
|
|
+ vmmc-supply = <&ldo9_reg>;
|
|
|
+ bus-width = <4>;
|
|
|
+};
|
|
|
+
|
|
|
+&mmc2 {
|
|
|
+ vmmc-supply = <&vmmcsd_fixed>;
|
|
|
+ bus-width = <8>;
|
|
|
+ ti,non-removable;
|
|
|
+};
|
|
|
+
|
|
|
+&mmc3 {
|
|
|
+ vmmc-supply = <&vmmcsdio_fixed>;
|
|
|
+ mmc-pwrseq = <&mmc3_pwrseq>;
|
|
|
+ bus-width = <4>;
|
|
|
+ non-removable;
|
|
|
+ cap-power-off-card;
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>;
|
|
|
+ interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
|
|
|
+ &omap5_pmx_core 0x168>;
|
|
|
+
|
|
|
+ #address-cells = <1>;
|
|
|
+ #size-cells = <0>;
|
|
|
+ wlcore: wlcore@2 {
|
|
|
+ compatible = "ti,wl1271";
|
|
|
+ reg = <2>;
|
|
|
+ interrupt-parent = <&gpio1>;
|
|
|
+ interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */
|
|
|
+ ref-clock-frequency = <26000000>;
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+&mmc4 {
|
|
|
+ status = "disabled";
|
|
|
+};
|
|
|
+
|
|
|
+&mmc5 {
|
|
|
+ status = "disabled";
|
|
|
+};
|
|
|
+
|
|
|
+&i2c1 {
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <&i2c1_pins>;
|
|
|
+
|
|
|
+ clock-frequency = <400000>;
|
|
|
+
|
|
|
+ palmas: palmas@48 {
|
|
|
+ compatible = "ti,palmas";
|
|
|
+ interrupts = <GIC_SPI 7 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
|
|
|
+ reg = <0x48>;
|
|
|
+ interrupt-controller;
|
|
|
+ #interrupt-cells = <2>;
|
|
|
+ ti,system-power-controller;
|
|
|
+
|
|
|
+ extcon_usb3: palmas_usb {
|
|
|
+ compatible = "ti,palmas-usb-vid";
|
|
|
+ ti,enable-vbus-detection;
|
|
|
+ ti,enable-id-detection;
|
|
|
+ ti,wakeup;
|
|
|
+ };
|
|
|
+
|
|
|
+ clk32kgaudio: palmas_clk32k@1 {
|
|
|
+ compatible = "ti,palmas-clk32kgaudio";
|
|
|
+ #clock-cells = <0>;
|
|
|
+ };
|
|
|
+
|
|
|
+ palmas_pmic {
|
|
|
+ compatible = "ti,palmas-pmic";
|
|
|
+ interrupt-parent = <&palmas>;
|
|
|
+ interrupts = <14 IRQ_TYPE_NONE>;
|
|
|
+ interrupt-name = "short-irq";
|
|
|
+
|
|
|
+ ti,ldo6-vibrator;
|
|
|
+
|
|
|
+ regulators {
|
|
|
+ smps123_reg: smps123 {
|
|
|
+ /* VDD_OPP_MPU */
|
|
|
+ regulator-name = "smps123";
|
|
|
+ regulator-min-microvolt = < 600000>;
|
|
|
+ regulator-max-microvolt = <1500000>;
|
|
|
+ regulator-always-on;
|
|
|
+ regulator-boot-on;
|
|
|
+ };
|
|
|
+
|
|
|
+ smps45_reg: smps45 {
|
|
|
+ /* VDD_OPP_MM */
|
|
|
+ regulator-name = "smps45";
|
|
|
+ regulator-min-microvolt = < 600000>;
|
|
|
+ regulator-max-microvolt = <1310000>;
|
|
|
+ regulator-always-on;
|
|
|
+ regulator-boot-on;
|
|
|
+ };
|
|
|
+
|
|
|
+ smps6_reg: smps6 {
|
|
|
+ /* VDD_DDR3 - over VDD_SMPS6 */
|
|
|
+ regulator-name = "smps6";
|
|
|
+ regulator-min-microvolt = <1200000>;
|
|
|
+ regulator-max-microvolt = <1200000>;
|
|
|
+ regulator-always-on;
|
|
|
+ regulator-boot-on;
|
|
|
+ };
|
|
|
+
|
|
|
+ smps7_reg: smps7 {
|
|
|
+ /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
|
|
|
+ regulator-name = "smps7";
|
|
|
+ regulator-min-microvolt = <1800000>;
|
|
|
+ regulator-max-microvolt = <1800000>;
|
|
|
+ regulator-always-on;
|
|
|
+ regulator-boot-on;
|
|
|
+ };
|
|
|
+
|
|
|
+ smps8_reg: smps8 {
|
|
|
+ /* VDD_OPP_CORE */
|
|
|
+ regulator-name = "smps8";
|
|
|
+ regulator-min-microvolt = < 600000>;
|
|
|
+ regulator-max-microvolt = <1310000>;
|
|
|
+ regulator-always-on;
|
|
|
+ regulator-boot-on;
|
|
|
+ };
|
|
|
+
|
|
|
+ smps9_reg: smps9 {
|
|
|
+ /* VDDA_2v1_AUD over VDD_2v1 */
|
|
|
+ regulator-name = "smps9";
|
|
|
+ regulator-min-microvolt = <2100000>;
|
|
|
+ regulator-max-microvolt = <2100000>;
|
|
|
+ ti,smps-range = <0x80>;
|
|
|
+ };
|
|
|
+
|
|
|
+ smps10_out2_reg: smps10_out2 {
|
|
|
+ /* VBUS_5V_OTG */
|
|
|
+ regulator-name = "smps10_out2";
|
|
|
+ regulator-min-microvolt = <5000000>;
|
|
|
+ regulator-max-microvolt = <5000000>;
|
|
|
+ regulator-always-on;
|
|
|
+ regulator-boot-on;
|
|
|
+ };
|
|
|
+
|
|
|
+ smps10_out1_reg: smps10_out1 {
|
|
|
+ /* VBUS_5V_OTG */
|
|
|
+ regulator-name = "smps10_out1";
|
|
|
+ regulator-min-microvolt = <5000000>;
|
|
|
+ regulator-max-microvolt = <5000000>;
|
|
|
+ };
|
|
|
+
|
|
|
+ ldo1_reg: ldo1 {
|
|
|
+ /* VDDAPHY_CAM: vdda_csiport */
|
|
|
+ regulator-name = "ldo1";
|
|
|
+ regulator-min-microvolt = <1500000>;
|
|
|
+ regulator-max-microvolt = <1800000>;
|
|
|
+ };
|
|
|
+
|
|
|
+ ldo2_reg: ldo2 {
|
|
|
+ /* VCC_2V8_DISP: Does not go anywhere */
|
|
|
+ regulator-name = "ldo2";
|
|
|
+ regulator-min-microvolt = <2800000>;
|
|
|
+ regulator-max-microvolt = <2800000>;
|
|
|
+ /* Unused */
|
|
|
+ status = "disabled";
|
|
|
+ };
|
|
|
+
|
|
|
+ ldo3_reg: ldo3 {
|
|
|
+ /* VDDAPHY_MDM: vdda_lli */
|
|
|
+ regulator-name = "ldo3";
|
|
|
+ regulator-min-microvolt = <1500000>;
|
|
|
+ regulator-max-microvolt = <1500000>;
|
|
|
+ regulator-boot-on;
|
|
|
+ /* Only if Modem is used */
|
|
|
+ status = "disabled";
|
|
|
+ };
|
|
|
+
|
|
|
+ ldo4_reg: ldo4 {
|
|
|
+ /* VDDAPHY_DISP: vdda_dsiport/hdmi */
|
|
|
+ regulator-name = "ldo4";
|
|
|
+ regulator-min-microvolt = <1500000>;
|
|
|
+ regulator-max-microvolt = <1800000>;
|
|
|
+ };
|
|
|
+
|
|
|
+ ldo5_reg: ldo5 {
|
|
|
+ /* VDDA_1V8_PHY: usb/sata/hdmi.. */
|
|
|
+ regulator-name = "ldo5";
|
|
|
+ regulator-min-microvolt = <1800000>;
|
|
|
+ regulator-max-microvolt = <1800000>;
|
|
|
+ regulator-always-on;
|
|
|
+ regulator-boot-on;
|
|
|
+ };
|
|
|
+
|
|
|
+ ldo6_reg: ldo6 {
|
|
|
+ /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
|
|
|
+ regulator-name = "ldo6";
|
|
|
+ regulator-min-microvolt = <1200000>;
|
|
|
+ regulator-max-microvolt = <1200000>;
|
|
|
+ regulator-always-on;
|
|
|
+ regulator-boot-on;
|
|
|
+ };
|
|
|
+
|
|
|
+ ldo7_reg: ldo7 {
|
|
|
+ /* VDD_VPP: vpp1 */
|
|
|
+ regulator-name = "ldo7";
|
|
|
+ regulator-min-microvolt = <2000000>;
|
|
|
+ regulator-max-microvolt = <2000000>;
|
|
|
+ /* Only for efuse reprograming! */
|
|
|
+ status = "disabled";
|
|
|
+ };
|
|
|
+
|
|
|
+ ldo8_reg: ldo8 {
|
|
|
+ /* VDD_3v0: Does not go anywhere */
|
|
|
+ regulator-name = "ldo8";
|
|
|
+ regulator-min-microvolt = <3000000>;
|
|
|
+ regulator-max-microvolt = <3000000>;
|
|
|
+ regulator-boot-on;
|
|
|
+ /* Unused */
|
|
|
+ status = "disabled";
|
|
|
+ };
|
|
|
+
|
|
|
+ ldo9_reg: ldo9 {
|
|
|
+ /* VCC_DV_SDIO: vdds_sdcard */
|
|
|
+ regulator-name = "ldo9";
|
|
|
+ regulator-min-microvolt = <1800000>;
|
|
|
+ regulator-max-microvolt = <3000000>;
|
|
|
+ regulator-boot-on;
|
|
|
+ };
|
|
|
+
|
|
|
+ ldoln_reg: ldoln {
|
|
|
+ /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
|
|
|
+ regulator-name = "ldoln";
|
|
|
+ regulator-min-microvolt = <1800000>;
|
|
|
+ regulator-max-microvolt = <1800000>;
|
|
|
+ regulator-always-on;
|
|
|
+ regulator-boot-on;
|
|
|
+ };
|
|
|
+
|
|
|
+ ldousb_reg: ldousb {
|
|
|
+ /* VDDA_3V_USB: VDDA_USBHS33 */
|
|
|
+ regulator-name = "ldousb";
|
|
|
+ regulator-min-microvolt = <3250000>;
|
|
|
+ regulator-max-microvolt = <3250000>;
|
|
|
+ regulator-always-on;
|
|
|
+ regulator-boot-on;
|
|
|
+ };
|
|
|
+
|
|
|
+ regen3_reg: regen3 {
|
|
|
+ /* REGEN3 controls LDO9 supply to card */
|
|
|
+ regulator-name = "regen3";
|
|
|
+ regulator-always-on;
|
|
|
+ regulator-boot-on;
|
|
|
+ };
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ palmas_power_button: palmas_power_button {
|
|
|
+ compatible = "ti,palmas-pwrbutton";
|
|
|
+ interrupt-parent = <&palmas>;
|
|
|
+ interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
|
|
|
+ wakeup-source;
|
|
|
+ };
|
|
|
+ };
|
|
|
+
|
|
|
+ twl6040: twl@4b {
|
|
|
+ compatible = "ti,twl6040";
|
|
|
+ reg = <0x4b>;
|
|
|
+
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <&twl6040_pins>;
|
|
|
+
|
|
|
+ interrupts = <GIC_SPI 119 IRQ_TYPE_NONE>; /* IRQ_SYS_2N cascaded to gic */
|
|
|
+ ti,audpwron-gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>; /* gpio line 141 */
|
|
|
+
|
|
|
+ vio-supply = <&smps7_reg>;
|
|
|
+ v2v1-supply = <&smps9_reg>;
|
|
|
+ enable-active-high;
|
|
|
+
|
|
|
+ clocks = <&clk32kgaudio>;
|
|
|
+ clock-names = "clk32k";
|
|
|
+ };
|
|
|
+};
|
|
|
+
|
|
|
+&mcpdm {
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <&mcpdm_pins>;
|
|
|
+ status = "okay";
|
|
|
+};
|
|
|
+
|
|
|
+&mcbsp1 {
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <&mcbsp1_pins>;
|
|
|
+ status = "okay";
|
|
|
+};
|
|
|
+
|
|
|
+&mcbsp2 {
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <&mcbsp2_pins>;
|
|
|
+ status = "okay";
|
|
|
+};
|
|
|
+
|
|
|
+&usbhshost {
|
|
|
+ port2-mode = "ehci-hsic";
|
|
|
+ port3-mode = "ehci-hsic";
|
|
|
+};
|
|
|
+
|
|
|
+&usbhsehci {
|
|
|
+ phys = <0 &hsusb2_phy &hsusb3_phy>;
|
|
|
+};
|
|
|
+
|
|
|
+&usb3 {
|
|
|
+ extcon = <&extcon_usb3>;
|
|
|
+ vbus-supply = <&smps10_out1_reg>;
|
|
|
+};
|
|
|
+
|
|
|
+&mcspi1 {
|
|
|
+
|
|
|
+};
|
|
|
+
|
|
|
+&mcspi2 {
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <&mcspi2_pins>;
|
|
|
+};
|
|
|
+
|
|
|
+&mcspi3 {
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <&mcspi3_pins>;
|
|
|
+};
|
|
|
+
|
|
|
+&uart1 {
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <&uart1_pins>;
|
|
|
+};
|
|
|
+
|
|
|
+&uart3 {
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <&uart3_pins>;
|
|
|
+ interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
|
|
|
+ <&omap5_pmx_core 0x19c>;
|
|
|
+};
|
|
|
+
|
|
|
+&uart5 {
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <&uart5_pins>;
|
|
|
+};
|
|
|
+
|
|
|
+&cpu0 {
|
|
|
+ cpu0-supply = <&smps123_reg>;
|
|
|
+};
|
|
|
+
|
|
|
+&dss {
|
|
|
+ status = "ok";
|
|
|
+};
|
|
|
+
|
|
|
+&hdmi {
|
|
|
+ status = "ok";
|
|
|
+
|
|
|
+ /* vdda-supply populated in board specific dts file */
|
|
|
+
|
|
|
+ pinctrl-names = "default";
|
|
|
+ pinctrl-0 = <&dss_hdmi_pins>;
|
|
|
+
|
|
|
+ port {
|
|
|
+ hdmi_out: endpoint {
|
|
|
+ remote-endpoint = <&tpd12s015_in>;
|
|
|
+ };
|
|
|
+ };
|
|
|
+};
|
Arnd Bergmann