brcmfmac: fix setting AP channel with new firmwares

Firmware for new chipsets is based on a new major version of code
internally maintained at Broadcom. E.g. brcmfmac4366b-pcie.bin (used for
BCM4366B1) is based on 10.10.69.3309 while brcmfmac43602-pcie.ap.bin was
based on 7.35.177.56.

Currently setting AP 5 GHz channel doesn't work reliably with BCM4366B1.
When setting e.g. 36 control channel with VHT80 (center channel 42)
firmware may randomly pick one of:
1) 52 control channel with 58 as center one
2) 100 control channel with 106 as center one
3) 116 control channel with 122 as center one
4) 149 control channel with 155 as center one

It seems new firmwares require setting AP mode (BRCMF_C_SET_AP) before
specifying a channel. Changing an order of firmware calls fixes the
problem. This requirement resulted in two separated "chanspec" calls,
one in AP code path and one in P2P path.

This fix was verified with BCM4366B1 and tested for regressions on
BCM43602.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.c

@@ -4442,7 +4442,7 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev,
 	struct brcmf_join_params join_params;
 	enum nl80211_iftype dev_role;
 	struct brcmf_fil_bss_enable_le bss_enable;
-	u16 chanspec;
+	u16 chanspec = chandef_to_chanspec(&cfg->d11inf, &settings->chandef);
 	bool mbss;
 	int is_11d;
 
@@ -4518,16 +4518,8 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev,
 
 	brcmf_config_ap_mgmt_ie(ifp->vif, &settings->beacon);
 
+	/* Parameters shared by all radio interfaces */
 	if (!mbss) {
-		chanspec = chandef_to_chanspec(&cfg->d11inf,
-					       &settings->chandef);
-		err = brcmf_fil_iovar_int_set(ifp, "chanspec", chanspec);
-		if (err < 0) {
-			brcmf_err("Set Channel failed: chspec=%d, %d\n",
-				  chanspec, err);
-			goto exit;
-		}
-
 		if (is_11d != ifp->vif->is_11d) {
 			err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_SET_REGULATORY,
 						    is_11d);
@@ -4575,6 +4567,8 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev,
 		err = -EINVAL;
 		goto exit;
 	}
+
+	/* Interface specific setup */
 	if (dev_role == NL80211_IFTYPE_AP) {
 		if ((brcmf_feat_is_enabled(ifp, BRCMF_FEAT_MBSS)) && (!mbss))
 			brcmf_fil_iovar_int_set(ifp, "mbss", 1);
@@ -4584,6 +4578,17 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev,
 			brcmf_err("setting AP mode failed %d\n", err);
 			goto exit;
 		}
+		if (!mbss) {
+			/* Firmware 10.x requires setting channel after enabling
+			 * AP and before bringing interface up.
+			 */
+			err = brcmf_fil_iovar_int_set(ifp, "chanspec", chanspec);
+			if (err < 0) {
+				brcmf_err("Set Channel failed: chspec=%d, %d\n",
+					  chanspec, err);
+				goto exit;
+			}
+		}
 		err = brcmf_fil_cmd_int_set(ifp, BRCMF_C_UP, 1);
 		if (err < 0) {
 			brcmf_err("BRCMF_C_UP error (%d)\n", err);
@@ -4605,7 +4610,13 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev,
 			goto exit;
 		}
 		brcmf_dbg(TRACE, "AP mode configuration complete\n");
-	} else {
+	} else if (dev_role == NL80211_IFTYPE_P2P_GO) {
+		err = brcmf_fil_iovar_int_set(ifp, "chanspec", chanspec);
+		if (err < 0) {
+			brcmf_err("Set Channel failed: chspec=%d, %d\n",
+				  chanspec, err);
+			goto exit;
+		}
 		err = brcmf_fil_bsscfg_data_set(ifp, "ssid", &ssid_le,
 						sizeof(ssid_le));
 		if (err < 0) {
@@ -4622,7 +4633,10 @@ brcmf_cfg80211_start_ap(struct wiphy *wiphy, struct net_device *ndev,
 		}
 
 		brcmf_dbg(TRACE, "GO mode configuration complete\n");
+	} else {
+		WARN_ON(1);
 	}
+
 	set_bit(BRCMF_VIF_STATUS_AP_CREATED, &ifp->vif->sme_state);
 	brcmf_net_setcarrier(ifp, true);