net-next: New ax88796 platform driver for Amiga X-Surf 100 Zorro board (m68k)

Add platform device driver to populate the ax88796 platform data from
information provided by the XSurf100 zorro device driver. The ax88796
module will be loaded through this module's probe function.

Signed-off-by: Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/8390/Kconfig

@@ -29,8 +29,8 @@ config PCMCIA_AXNET
 	  called axnet_cs.  If unsure, say N.
 
 config AX88796
-	tristate "ASIX AX88796 NE2000 clone support"
-	depends on (ARM || MIPS || SUPERH)
+	tristate "ASIX AX88796 NE2000 clone support" if !ZORRO
+	depends on (ARM || MIPS || SUPERH || ZORRO || COMPILE_TEST)
 	select CRC32
 	select PHYLIB
 	select MDIO_BITBANG
@@ -45,6 +45,19 @@ config AX88796_93CX6
 	---help---
 	  Select this if your platform comes with an external 93CX6 eeprom.
 
+config XSURF100
+	tristate "Amiga XSurf 100 AX88796/NE2000 clone support"
+	depends on ZORRO
+	select AX88796
+	select ASIX_PHY
+	help
+	  This driver is for the Individual Computers X-Surf 100 Ethernet
+	  card (based on the Asix AX88796 chip). If you have such a card,
+	  say Y. Otherwise, say N.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called xsurf100.
+
 config HYDRA
 	tristate "Hydra support"
 	depends on ZORRO

drivers/net/ethernet/8390/Makefile

@@ -16,4 +16,5 @@ obj-$(CONFIG_PCMCIA_PCNET) += pcnet_cs.o 8390.o
 obj-$(CONFIG_STNIC) += stnic.o 8390.o
 obj-$(CONFIG_ULTRA) += smc-ultra.o 8390.o
 obj-$(CONFIG_WD80x3) += wd.o 8390.o
+obj-$(CONFIG_XSURF100) += xsurf100.o
 obj-$(CONFIG_ZORRO8390) += zorro8390.o

drivers/net/ethernet/8390/xsurf100.c

@@ -0,0 +1,382 @@
+// SPDX-License-Identifier: GPL-2.0
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/platform_device.h>
+#include <linux/zorro.h>
+#include <net/ax88796.h>
+#include <asm/amigaints.h>
+
+#define ZORRO_PROD_INDIVIDUAL_COMPUTERS_X_SURF100 \
+		ZORRO_ID(INDIVIDUAL_COMPUTERS, 0x64, 0)
+
+#define XS100_IRQSTATUS_BASE 0x40
+#define XS100_8390_BASE 0x800
+
+/* Longword-access area. Translated to 2 16-bit access cycles by the
+ * X-Surf 100 FPGA
+ */
+#define XS100_8390_DATA32_BASE 0x8000
+#define XS100_8390_DATA32_SIZE 0x2000
+/* Sub-Areas for fast data register access; addresses relative to area begin */
+#define XS100_8390_DATA_READ32_BASE 0x0880
+#define XS100_8390_DATA_WRITE32_BASE 0x0C80
+#define XS100_8390_DATA_AREA_SIZE 0x80
+
+#define __NS8390_init ax_NS8390_init
+
+/* force unsigned long back to 'void __iomem *' */
+#define ax_convert_addr(_a) ((void __force __iomem *)(_a))
+
+#define ei_inb(_a) z_readb(ax_convert_addr(_a))
+#define ei_outb(_v, _a) z_writeb(_v, ax_convert_addr(_a))
+
+#define ei_inw(_a) z_readw(ax_convert_addr(_a))
+#define ei_outw(_v, _a) z_writew(_v, ax_convert_addr(_a))
+
+#define ei_inb_p(_a) ei_inb(_a)
+#define ei_outb_p(_v, _a) ei_outb(_v, _a)
+
+/* define EI_SHIFT() to take into account our register offsets */
+#define EI_SHIFT(x) (ei_local->reg_offset[(x)])
+
+/* Ensure we have our RCR base value */
+#define AX88796_PLATFORM
+
+static unsigned char version[] =
+		"ax88796.c: Copyright 2005,2007 Simtec Electronics\n";
+
+#include "lib8390.c"
+
+/* from ne.c */
+#define NE_CMD		EI_SHIFT(0x00)
+#define NE_RESET	EI_SHIFT(0x1f)
+#define NE_DATAPORT	EI_SHIFT(0x10)
+
+struct xsurf100_ax_plat_data {
+	struct ax_plat_data ax;
+	void __iomem *base_regs;
+	void __iomem *data_area;
+};
+
+static int is_xsurf100_network_irq(struct platform_device *pdev)
+{
+	struct xsurf100_ax_plat_data *xs100 = dev_get_platdata(&pdev->dev);
+
+	return (readw(xs100->base_regs + XS100_IRQSTATUS_BASE) & 0xaaaa) != 0;
+}
+
+/* These functions guarantee that the iomem is accessed with 32 bit
+ * cycles only. z_memcpy_fromio / z_memcpy_toio don't
+ */
+static void z_memcpy_fromio32(void *dst, const void __iomem *src, size_t bytes)
+{
+	while (bytes > 32) {
+		asm __volatile__
+		   ("movem.l (%0)+,%%d0-%%d7\n"
+		    "movem.l %%d0-%%d7,(%1)\n"
+		    "adda.l #32,%1" : "=a"(src), "=a"(dst)
+		    : "0"(src), "1"(dst) : "d0", "d1", "d2", "d3", "d4",
+					   "d5", "d6", "d7", "memory");
+		bytes -= 32;
+	}
+	while (bytes) {
+		*(uint32_t *)dst = z_readl(src);
+		src += 4;
+		dst += 4;
+		bytes -= 4;
+	}
+}
+
+static void z_memcpy_toio32(void __iomem *dst, const void *src, size_t bytes)
+{
+	while (bytes) {
+		z_writel(*(const uint32_t *)src, dst);
+		src += 4;
+		dst += 4;
+		bytes -= 4;
+	}
+}
+
+static void xs100_write(struct net_device *dev, const void *src,
+			unsigned int count)
+{
+	struct ei_device *ei_local = netdev_priv(dev);
+	struct platform_device *pdev = to_platform_device(dev->dev.parent);
+	struct xsurf100_ax_plat_data *xs100 = dev_get_platdata(&pdev->dev);
+
+	/* copy whole blocks */
+	while (count > XS100_8390_DATA_AREA_SIZE) {
+		z_memcpy_toio32(xs100->data_area +
+				XS100_8390_DATA_WRITE32_BASE, src,
+				XS100_8390_DATA_AREA_SIZE);
+		src += XS100_8390_DATA_AREA_SIZE;
+		count -= XS100_8390_DATA_AREA_SIZE;
+	}
+	/* copy whole dwords */
+	z_memcpy_toio32(xs100->data_area + XS100_8390_DATA_WRITE32_BASE,
+			src, count & ~3);
+	src += count & ~3;
+	if (count & 2) {
+		ei_outw(*(uint16_t *)src, ei_local->mem + NE_DATAPORT);
+		src += 2;
+	}
+	if (count & 1)
+		ei_outb(*(uint8_t *)src, ei_local->mem + NE_DATAPORT);
+}
+
+static void xs100_read(struct net_device *dev, void *dst, unsigned int count)
+{
+	struct ei_device *ei_local = netdev_priv(dev);
+	struct platform_device *pdev = to_platform_device(dev->dev.parent);
+	struct xsurf100_ax_plat_data *xs100 = dev_get_platdata(&pdev->dev);
+
+	/* copy whole blocks */
+	while (count > XS100_8390_DATA_AREA_SIZE) {
+		z_memcpy_fromio32(dst, xs100->data_area +
+				  XS100_8390_DATA_READ32_BASE,
+				  XS100_8390_DATA_AREA_SIZE);
+		dst += XS100_8390_DATA_AREA_SIZE;
+		count -= XS100_8390_DATA_AREA_SIZE;
+	}
+	/* copy whole dwords */
+	z_memcpy_fromio32(dst, xs100->data_area + XS100_8390_DATA_READ32_BASE,
+			  count & ~3);
+	dst += count & ~3;
+	if (count & 2) {
+		*(uint16_t *)dst = ei_inw(ei_local->mem + NE_DATAPORT);
+		dst += 2;
+	}
+	if (count & 1)
+		*(uint8_t *)dst = ei_inb(ei_local->mem + NE_DATAPORT);
+}
+
+/* Block input and output, similar to the Crynwr packet driver. If
+ * you are porting to a new ethercard, look at the packet driver
+ * source for hints. The NEx000 doesn't share the on-board packet
+ * memory -- you have to put the packet out through the "remote DMA"
+ * dataport using ei_outb.
+ */
+static void xs100_block_input(struct net_device *dev, int count,
+			      struct sk_buff *skb, int ring_offset)
+{
+	struct ei_device *ei_local = netdev_priv(dev);
+	void __iomem *nic_base = ei_local->mem;
+	char *buf = skb->data;
+
+	if (ei_local->dmaing) {
+		netdev_err(dev,
+			   "DMAing conflict in %s [DMAstat:%d][irqlock:%d]\n",
+			   __func__,
+			   ei_local->dmaing, ei_local->irqlock);
+		return;
+	}
+
+	ei_local->dmaing |= 0x01;
+
+	ei_outb(E8390_NODMA + E8390_PAGE0 + E8390_START, nic_base + NE_CMD);
+	ei_outb(count & 0xff, nic_base + EN0_RCNTLO);
+	ei_outb(count >> 8, nic_base + EN0_RCNTHI);
+	ei_outb(ring_offset & 0xff, nic_base + EN0_RSARLO);
+	ei_outb(ring_offset >> 8, nic_base + EN0_RSARHI);
+	ei_outb(E8390_RREAD + E8390_START, nic_base + NE_CMD);
+
+	xs100_read(dev, buf, count);
+
+	ei_local->dmaing &= ~1;
+}
+
+static void xs100_block_output(struct net_device *dev, int count,
+			       const unsigned char *buf, const int start_page)
+{
+	struct ei_device *ei_local = netdev_priv(dev);
+	void __iomem *nic_base = ei_local->mem;
+	unsigned long dma_start;
+
+	/* Round the count up for word writes. Do we need to do this?
+	 * What effect will an odd byte count have on the 8390?  I
+	 * should check someday.
+	 */
+	if (ei_local->word16 && (count & 0x01))
+		count++;
+
+	/* This *shouldn't* happen. If it does, it's the last thing
+	 * you'll see
+	 */
+	if (ei_local->dmaing) {
+		netdev_err(dev,
+			   "DMAing conflict in %s [DMAstat:%d][irqlock:%d]\n",
+			   __func__,
+			   ei_local->dmaing, ei_local->irqlock);
+		return;
+	}
+
+	ei_local->dmaing |= 0x01;
+	/* We should already be in page 0, but to be safe... */
+	ei_outb(E8390_PAGE0 + E8390_START + E8390_NODMA, nic_base + NE_CMD);
+
+	ei_outb(ENISR_RDC, nic_base + EN0_ISR);
+
+	/* Now the normal output. */
+	ei_outb(count & 0xff, nic_base + EN0_RCNTLO);
+	ei_outb(count >> 8, nic_base + EN0_RCNTHI);
+	ei_outb(0x00, nic_base + EN0_RSARLO);
+	ei_outb(start_page, nic_base + EN0_RSARHI);
+
+	ei_outb(E8390_RWRITE + E8390_START, nic_base + NE_CMD);
+
+	xs100_write(dev, buf, count);
+
+	dma_start = jiffies;
+
+	while ((ei_inb(nic_base + EN0_ISR) & ENISR_RDC) == 0) {
+		if (jiffies - dma_start > 2 * HZ / 100) {	/* 20ms */
+			netdev_warn(dev, "timeout waiting for Tx RDC.\n");
+			ei_local->reset_8390(dev);
+			ax_NS8390_init(dev, 1);
+			break;
+		}
+	}
+
+	ei_outb(ENISR_RDC, nic_base + EN0_ISR);	/* Ack intr. */
+	ei_local->dmaing &= ~0x01;
+}
+
+static int xsurf100_probe(struct zorro_dev *zdev,
+			  const struct zorro_device_id *ent)
+{
+	struct platform_device *pdev;
+	struct xsurf100_ax_plat_data ax88796_data;
+	struct resource res[2] = {
+		DEFINE_RES_NAMED(IRQ_AMIGA_PORTS, 1, NULL,
+				 IORESOURCE_IRQ | IORESOURCE_IRQ_SHAREABLE),
+		DEFINE_RES_MEM(zdev->resource.start + XS100_8390_BASE,
+			       4 * 0x20)
+	};
+	int reg;
+	/* This table is referenced in the device structure, so it must
+	 * outlive the scope of xsurf100_probe.
+	 */
+	static u32 reg_offsets[32];
+	int ret = 0;
+
+	/* X-Surf 100 control and 32 bit ring buffer data access areas.
+	 * These resources are not used by the ax88796 driver, so must
+	 * be requested here and passed via platform data.
+	 */
+
+	if (!request_mem_region(zdev->resource.start, 0x100, zdev->name)) {
+		dev_err(&zdev->dev, "cannot reserve X-Surf 100 control registers\n");
+		return -ENXIO;
+	}
+
+	if (!request_mem_region(zdev->resource.start +
+				XS100_8390_DATA32_BASE,
+				XS100_8390_DATA32_SIZE,
+				"X-Surf 100 32-bit data access")) {
+		dev_err(&zdev->dev, "cannot reserve 32-bit area\n");
+		ret = -ENXIO;
+		goto exit_req;
+	}
+
+	for (reg = 0; reg < 0x20; reg++)
+		reg_offsets[reg] = 4 * reg;
+
+	memset(&ax88796_data, 0, sizeof(ax88796_data));
+	ax88796_data.ax.flags = AXFLG_HAS_EEPROM;
+	ax88796_data.ax.wordlength = 2;
+	ax88796_data.ax.dcr_val = 0x48;
+	ax88796_data.ax.rcr_val = 0x40;
+	ax88796_data.ax.reg_offsets = reg_offsets;
+	ax88796_data.ax.check_irq = is_xsurf100_network_irq;
+	ax88796_data.base_regs = ioremap(zdev->resource.start, 0x100);
+
+	/* error handling for ioremap regs */
+	if (!ax88796_data.base_regs) {
+		dev_err(&zdev->dev, "Cannot ioremap area %pR (registers)\n",
+			&zdev->resource);
+
+		ret = -ENXIO;
+		goto exit_req2;
+	}
+
+	ax88796_data.data_area = ioremap(zdev->resource.start +
+			XS100_8390_DATA32_BASE, XS100_8390_DATA32_SIZE);
+
+	/* error handling for ioremap data */
+	if (!ax88796_data.data_area) {
+		dev_err(&zdev->dev,
+			"Cannot ioremap area %pR offset %x (32-bit access)\n",
+			&zdev->resource,  XS100_8390_DATA32_BASE);
+
+		ret = -ENXIO;
+		goto exit_mem;
+	}
+
+	ax88796_data.ax.block_output = xs100_block_output;
+	ax88796_data.ax.block_input = xs100_block_input;
+
+	pdev = platform_device_register_resndata(&zdev->dev, "ax88796",
+						 zdev->slotaddr, res, 2,
+						 &ax88796_data,
+						 sizeof(ax88796_data));
+
+	if (IS_ERR(pdev)) {
+		dev_err(&zdev->dev, "cannot register platform device\n");
+		ret = -ENXIO;
+		goto exit_mem2;
+	}
+
+	zorro_set_drvdata(zdev, pdev);
+
+	if (!ret)
+		return 0;
+
+ exit_mem2:
+	iounmap(ax88796_data.data_area);
+
+ exit_mem:
+	iounmap(ax88796_data.base_regs);
+
+ exit_req2:
+	release_mem_region(zdev->resource.start + XS100_8390_DATA32_BASE,
+			   XS100_8390_DATA32_SIZE);
+
+ exit_req:
+	release_mem_region(zdev->resource.start, 0x100);
+
+	return ret;
+}
+
+static void xsurf100_remove(struct zorro_dev *zdev)
+{
+	struct platform_device *pdev = zorro_get_drvdata(zdev);
+	struct xsurf100_ax_plat_data *xs100 = dev_get_platdata(&pdev->dev);
+
+	platform_device_unregister(pdev);
+
+	iounmap(xs100->base_regs);
+	release_mem_region(zdev->resource.start, 0x100);
+	iounmap(xs100->data_area);
+	release_mem_region(zdev->resource.start + XS100_8390_DATA32_BASE,
+			   XS100_8390_DATA32_SIZE);
+}
+
+static const struct zorro_device_id xsurf100_zorro_tbl[] = {
+	{ ZORRO_PROD_INDIVIDUAL_COMPUTERS_X_SURF100, },
+	{ 0 }
+};
+
+MODULE_DEVICE_TABLE(zorro, xsurf100_zorro_tbl);
+
+static struct zorro_driver xsurf100_driver = {
+	.name           = "xsurf100",
+	.id_table       = xsurf100_zorro_tbl,
+	.probe          = xsurf100_probe,
+	.remove         = xsurf100_remove,
+};
+
+module_driver(xsurf100_driver, zorro_register_driver, zorro_unregister_driver);
+
+MODULE_DESCRIPTION("X-Surf 100 driver");
+MODULE_AUTHOR("Michael Karcher <kernel@mkarcher.dialup.fu-berlin.de>");
+MODULE_LICENSE("GPL v2");