Merge branches 'pci/host-designware', 'pci/host-imx6', 'pci/host-mvebu' and 'pci/host-tegra' into next

* pci/host-designware:
  PCI: designware: Remove unnecessary use of 'conf_lock' spinlock
  PCI: designware: Use new OF interrupt mapping when possible
  PCI: designware: Fix iATU programming for cfg1, io and mem viewport
  PCI: designware: Fix comment for setting number of lanes

* pci/host-imx6:
  PCI: designware: Split Exynos and i.MX bindings

* pci/host-mvebu:
  PCI: mvebu: Use '%pa' for printing 'phys_addr_t' type
  PCI: mvebu: Remove unnecessary use of 'conf_lock' spinlock
  PCI: mvebu: split PCIe BARs into multiple MBus windows when needed
  bus: mvebu-mbus: allow several windows with the same target/attribute
  bus: mvebu-mbus: Avoid setting an undefined window size
  PCI: mvebu: fix off-by-one in the computed size of the mbus windows

* pci/host-tegra:
  PCI: tegra: Use new OF interrupt mapping when possible

Documentation/devicetree/bindings/pci/designware-pcie.txt

@@ -1,15 +1,7 @@
 * Synopsys Designware PCIe interface
 
 Required properties:
-- compatible: should contain "snps,dw-pcie" to identify the
-	core, plus an identifier for the specific instance, such
-	as "samsung,exynos5440-pcie" or "fsl,imx6q-pcie".
-- reg: base addresses and lengths of the pcie controller,
-	the phy controller, additional register for the phy controller.
-- interrupts: interrupt values for level interrupt,
-	pulse interrupt, special interrupt.
-- clocks: from common clock binding: handle to pci clock.
-- clock-names: from common clock binding: should be "pcie" and "pcie_bus".
+- compatible: should contain "snps,dw-pcie" to identify the core.
 - #address-cells: set to <3>
 - #size-cells: set to <2>
 - device_type: set to "pci"
@@ -19,65 +11,11 @@ Required properties:
 	to define the mapping of the PCIe interface to interrupt
 	numbers.
 - num-lanes: number of lanes to use
+- clocks: Must contain an entry for each entry in clock-names.
+	See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+	- "pcie"
+	- "pcie_bus"
 
 Optional properties:
 - reset-gpio: gpio pin number of power good signal
-
-Optional properties for fsl,imx6q-pcie
-- power-on-gpio: gpio pin number of power-enable signal
-- wake-up-gpio: gpio pin number of incoming wakeup signal
-- disable-gpio: gpio pin number of outgoing rfkill/endpoint disable signal
-
-Example:
-
-SoC specific DT Entry:
-
-	pcie@290000 {
-		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
-		reg = <0x290000 0x1000
-			0x270000 0x1000
-			0x271000 0x40>;
-		interrupts = <0 20 0>, <0 21 0>, <0 22 0>;
-		clocks = <&clock 28>, <&clock 27>;
-		clock-names = "pcie", "pcie_bus";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000   /* configuration space */
-			  0x81000000 0 0	  0x40001000 0 0x00010000   /* downstream I/O */
-			  0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0x0 0 &gic 53>;
-		num-lanes = <4>;
-	};
-
-	pcie@2a0000 {
-		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
-		reg = <0x2a0000 0x1000
-			0x272000 0x1000
-			0x271040 0x40>;
-		interrupts = <0 23 0>, <0 24 0>, <0 25 0>;
-		clocks = <&clock 29>, <&clock 27>;
-		clock-names = "pcie", "pcie_bus";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000   /* configuration space */
-			  0x81000000 0 0	  0x60001000 0 0x00010000   /* downstream I/O */
-			  0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0x0 0 &gic 56>;
-		num-lanes = <4>;
-	};
-
-Board specific DT Entry:
-
-	pcie@290000 {
-		reset-gpio = <&pin_ctrl 5 0>;
-	};
-
-	pcie@2a0000 {
-		reset-gpio = <&pin_ctrl 22 0>;
-	};

Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt

@@ -0,0 +1,38 @@
+* Freescale i.MX6 PCIe interface
+
+This PCIe host controller is based on the Synopsis Designware PCIe IP
+and thus inherits all the common properties defined in designware-pcie.txt.
+
+Required properties:
+- compatible: "fsl,imx6q-pcie"
+- reg: base addresse and length of the pcie controller
+- interrupts: A list of interrupt outputs of the controller. Must contain an
+  entry for each entry in the interrupt-names property.
+- interrupt-names: Must include the following entries:
+	- "msi": The interrupt that is asserted when an MSI is received
+- clock-names: Must include the following additional entries:
+	- "pcie_phy"
+
+Example:
+
+	pcie@0x01000000 {
+		compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
+		reg = <0x01ffc000 0x4000>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000
+			  0x81000000 0 0          0x01f80000 0 0x00010000
+			  0x82000000 0 0x01000000 0x01000000 0 0x00f00000>;
+		num-lanes = <1>;
+		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "msi";
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0x7>;
+		interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+		                <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+		                <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+		                <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&clks 144>, <&clks 206>, <&clks 189>;
+		clock-names = "pcie", "pcie_bus", "pcie_phy";
+	};

Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt

@@ -0,0 +1,65 @@
+* Samsung Exynos 5440 PCIe interface
+
+This PCIe host controller is based on the Synopsis Designware PCIe IP
+and thus inherits all the common properties defined in designware-pcie.txt.
+
+Required properties:
+- compatible: "samsung,exynos5440-pcie"
+- reg: base addresses and lengths of the pcie controller,
+	the phy controller, additional register for the phy controller.
+- interrupts: A list of interrupt outputs for level interrupt,
+	pulse interrupt, special interrupt.
+
+Example:
+
+SoC specific DT Entry:
+
+	pcie@290000 {
+		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
+		reg = <0x290000 0x1000
+			0x270000 0x1000
+			0x271000 0x40>;
+		interrupts = <0 20 0>, <0 21 0>, <0 22 0>;
+		clocks = <&clock 28>, <&clock 27>;
+		clock-names = "pcie", "pcie_bus";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000   /* configuration space */
+			  0x81000000 0 0	  0x40001000 0 0x00010000   /* downstream I/O */
+			  0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+		num-lanes = <4>;
+	};
+
+	pcie@2a0000 {
+		compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
+		reg = <0x2a0000 0x1000
+			0x272000 0x1000
+			0x271040 0x40>;
+		interrupts = <0 23 0>, <0 24 0>, <0 25 0>;
+		clocks = <&clock 29>, <&clock 27>;
+		clock-names = "pcie", "pcie_bus";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000   /* configuration space */
+			  0x81000000 0 0	  0x60001000 0 0x00010000   /* downstream I/O */
+			  0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+		num-lanes = <4>;
+	};
+
+Board specific DT Entry:
+
+	pcie@290000 {
+		reset-gpio = <&pin_ctrl 5 0>;
+	};
+
+	pcie@2a0000 {
+		reset-gpio = <&pin_ctrl 22 0>;
+	};

drivers/bus/mvebu-mbus.c

@@ -56,6 +56,7 @@
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/debugfs.h>
+#include <linux/log2.h>
 
 /*
  * DDR target is the same on all platforms.
@@ -222,12 +223,6 @@ static int mvebu_mbus_window_conflicts(struct mvebu_mbus_state *mbus,
 		 */
 		if ((u64)base < wend && end > wbase)
 			return 0;
-
-		/*
-		 * Check if target/attribute conflicts
-		 */
-		if (target == wtarget && attr == wattr)
-			return 0;
 	}
 
 	return 1;
@@ -266,6 +261,17 @@ static int mvebu_mbus_setup_window(struct mvebu_mbus_state *mbus,
 		mbus->soc->win_cfg_offset(win);
 	u32 ctrl, remap_addr;
 
+	if (!is_power_of_2(size)) {
+		WARN(true, "Invalid MBus window size: 0x%zx\n", size);
+		return -EINVAL;
+	}
+
+	if ((base & (phys_addr_t)(size - 1)) != 0) {
+		WARN(true, "Invalid MBus base/size: %pa len 0x%zx\n", &base,
+		     size);
+		return -EINVAL;
+	}
+
 	ctrl = ((size - 1) & WIN_CTRL_SIZE_MASK) |
 		(attr << WIN_CTRL_ATTR_SHIFT)    |
 		(target << WIN_CTRL_TGT_SHIFT)   |
@@ -413,6 +419,10 @@ static int mvebu_devs_debug_show(struct seq_file *seq, void *v)
 			   win, (unsigned long long)wbase,
 			   (unsigned long long)(wbase + wsize), wtarget, wattr);
 
+		if (!is_power_of_2(wsize) ||
+		    ((wbase & (u64)(wsize - 1)) != 0))
+			seq_puts(seq, " (Invalid base/size!!)");
+
 		if (win < mbus->soc->num_remappable_wins) {
 			seq_printf(seq, " (remap %016llx)\n",
 				   (unsigned long long)wremap);

drivers/pci/host/pci-exynos.c

@@ -545,7 +545,6 @@ static int __init add_pcie_port(struct pcie_port *pp,
 	pp->root_bus_nr = -1;
 	pp->ops = &exynos_pcie_host_ops;
 
-	spin_lock_init(&pp->conf_lock);
 	ret = dw_pcie_host_init(pp);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to initialize host\n");

drivers/pci/host/pci-imx6.c

@@ -507,7 +507,6 @@ static int __init imx6_add_pcie_port(struct pcie_port *pp,
 	pp->root_bus_nr = -1;
 	pp->ops = &imx6_pcie_host_ops;
 
-	spin_lock_init(&pp->conf_lock);
 	ret = dw_pcie_host_init(pp);
 	if (ret) {
 		dev_err(&pdev->dev, "failed to initialize host\n");

drivers/pci/host/pci-mvebu.c

@@ -113,7 +113,6 @@ struct mvebu_pcie {
 struct mvebu_pcie_port {
 	char *name;
 	void __iomem *base;
-	spinlock_t conf_lock;
 	u32 port;
 	u32 lane;
 	int devfn;
@@ -293,6 +292,60 @@ static int mvebu_pcie_hw_wr_conf(struct mvebu_pcie_port *port,
 	return PCIBIOS_SUCCESSFUL;
 }
 
+/*
+ * Remove windows, starting from the largest ones to the smallest
+ * ones.
+ */
+static void mvebu_pcie_del_windows(struct mvebu_pcie_port *port,
+				   phys_addr_t base, size_t size)
+{
+	while (size) {
+		size_t sz = 1 << (fls(size) - 1);
+
+		mvebu_mbus_del_window(base, sz);
+		base += sz;
+		size -= sz;
+	}
+}
+
+/*
+ * MBus windows can only have a power of two size, but PCI BARs do not
+ * have this constraint. Therefore, we have to split the PCI BAR into
+ * areas each having a power of two size. We start from the largest
+ * one (i.e highest order bit set in the size).
+ */
+static void mvebu_pcie_add_windows(struct mvebu_pcie_port *port,
+				   unsigned int target, unsigned int attribute,
+				   phys_addr_t base, size_t size,
+				   phys_addr_t remap)
+{
+	size_t size_mapped = 0;
+
+	while (size) {
+		size_t sz = 1 << (fls(size) - 1);
+		int ret;
+
+		ret = mvebu_mbus_add_window_remap_by_id(target, attribute, base,
+							sz, remap);
+		if (ret) {
+			phys_addr_t end = base + sz - 1;
+
+			dev_err(&port->pcie->pdev->dev,
+				"Could not create MBus window at [mem %pa-%pa]: %d\n",
+				&base, &end, ret);
+			mvebu_pcie_del_windows(port, base - size_mapped,
+					       size_mapped);
+			return;
+		}
+
+		size -= sz;
+		size_mapped += sz;
+		base += sz;
+		if (remap != MVEBU_MBUS_NO_REMAP)
+			remap += sz;
+	}
+}
+
 static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
 {
 	phys_addr_t iobase;
@@ -304,8 +357,8 @@ static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
 
 		/* If a window was configured, remove it */
 		if (port->iowin_base) {
-			mvebu_mbus_del_window(port->iowin_base,
-					      port->iowin_size);
+			mvebu_pcie_del_windows(port, port->iowin_base,
+					       port->iowin_size);
 			port->iowin_base = 0;
 			port->iowin_size = 0;
 		}
@@ -331,11 +384,11 @@ static void mvebu_pcie_handle_iobase_change(struct mvebu_pcie_port *port)
 	port->iowin_base = port->pcie->io.start + iobase;
 	port->iowin_size = ((0xFFF | ((port->bridge.iolimit & 0xF0) << 8) |
 			    (port->bridge.iolimitupper << 16)) -
-			    iobase);
+			    iobase) + 1;
 
-	mvebu_mbus_add_window_remap_by_id(port->io_target, port->io_attr,
-					  port->iowin_base, port->iowin_size,
-					  iobase);
+	mvebu_pcie_add_windows(port, port->io_target, port->io_attr,
+			       port->iowin_base, port->iowin_size,
+			       iobase);
 }
 
 static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
@@ -346,8 +399,8 @@ static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
 
 		/* If a window was configured, remove it */
 		if (port->memwin_base) {
-			mvebu_mbus_del_window(port->memwin_base,
-					      port->memwin_size);
+			mvebu_pcie_del_windows(port, port->memwin_base,
+					       port->memwin_size);
 			port->memwin_base = 0;
 			port->memwin_size = 0;
 		}
@@ -364,10 +417,11 @@ static void mvebu_pcie_handle_membase_change(struct mvebu_pcie_port *port)
 	port->memwin_base  = ((port->bridge.membase & 0xFFF0) << 16);
 	port->memwin_size  =
 		(((port->bridge.memlimit & 0xFFF0) << 16) | 0xFFFFF) -
-		port->memwin_base;
+		port->memwin_base + 1;
 
-	mvebu_mbus_add_window_by_id(port->mem_target, port->mem_attr,
-				    port->memwin_base, port->memwin_size);
+	mvebu_pcie_add_windows(port, port->mem_target, port->mem_attr,
+			       port->memwin_base, port->memwin_size,
+			       MVEBU_MBUS_NO_REMAP);
 }
 
 /*
@@ -585,7 +639,6 @@ static int mvebu_pcie_wr_conf(struct pci_bus *bus, u32 devfn,
 {
 	struct mvebu_pcie *pcie = sys_to_pcie(bus->sysdata);
 	struct mvebu_pcie_port *port;
-	unsigned long flags;
 	int ret;
 
 	port = mvebu_pcie_find_port(pcie, bus, devfn);
@@ -611,10 +664,8 @@ static int mvebu_pcie_wr_conf(struct pci_bus *bus, u32 devfn,
 		return PCIBIOS_DEVICE_NOT_FOUND;
 
 	/* Access the real PCIe interface */
-	spin_lock_irqsave(&port->conf_lock, flags);
 	ret = mvebu_pcie_hw_wr_conf(port, bus, devfn,
 				    where, size, val);
-	spin_unlock_irqrestore(&port->conf_lock, flags);
 
 	return ret;
 }
@@ -625,7 +676,6 @@ static int mvebu_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
 {
 	struct mvebu_pcie *pcie = sys_to_pcie(bus->sysdata);
 	struct mvebu_pcie_port *port;
-	unsigned long flags;
 	int ret;
 
 	port = mvebu_pcie_find_port(pcie, bus, devfn);
@@ -657,10 +707,8 @@ static int mvebu_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
 	}
 
 	/* Access the real PCIe interface */
-	spin_lock_irqsave(&port->conf_lock, flags);
 	ret = mvebu_pcie_hw_rd_conf(port, bus, devfn,
 				    where, size, val);
-	spin_unlock_irqrestore(&port->conf_lock, flags);
 
 	return ret;
 }
@@ -743,14 +791,21 @@ static resource_size_t mvebu_pcie_align_resource(struct pci_dev *dev,
 
 	/*
 	 * On the PCI-to-PCI bridge side, the I/O windows must have at
-	 * least a 64 KB size and be aligned on their size, and the
-	 * memory windows must have at least a 1 MB size and be
-	 * aligned on their size
+	 * least a 64 KB size and the memory windows must have at
+	 * least a 1 MB size. Moreover, MBus windows need to have a
+	 * base address aligned on their size, and their size must be
+	 * a power of two. This means that if the BAR doesn't have a
+	 * power of two size, several MBus windows will actually be
+	 * created. We need to ensure that the biggest MBus window
+	 * (which will be the first one) is aligned on its size, which
+	 * explains the rounddown_pow_of_two() being done here.
 	 */
 	if (res->flags & IORESOURCE_IO)
-		return round_up(start, max_t(resource_size_t, SZ_64K, size));
+		return round_up(start, max_t(resource_size_t, SZ_64K,
+					     rounddown_pow_of_two(size)));
 	else if (res->flags & IORESOURCE_MEM)
-		return round_up(start, max_t(resource_size_t, SZ_1M, size));
+		return round_up(start, max_t(resource_size_t, SZ_1M,
+					     rounddown_pow_of_two(size)));
 	else
 		return start;
 }
@@ -1000,7 +1055,6 @@ static int mvebu_pcie_probe(struct platform_device *pdev)
 		mvebu_pcie_set_local_dev_nr(port, 1);
 
 		port->dn = child;
-		spin_lock_init(&port->conf_lock);
 		mvebu_sw_pci_bridge_init(port);
 		i++;
 	}

drivers/pci/host/pci-tegra.c

@@ -639,10 +639,15 @@ static int tegra_pcie_setup(int nr, struct pci_sys_data *sys)
 static int tegra_pcie_map_irq(const struct pci_dev *pdev, u8 slot, u8 pin)
 {
 	struct tegra_pcie *pcie = sys_to_pcie(pdev->bus->sysdata);
+	int irq;
 
 	tegra_cpuidle_pcie_irqs_in_use();
 
-	return pcie->irq;
+	irq = of_irq_parse_and_map_pci(pdev, slot, pin);
+	if (!irq)
+		irq = pcie->irq;
+
+	return irq;
 }
 
 static void tegra_pcie_add_bus(struct pci_bus *bus)

drivers/pci/host/pcie-designware.c

@@ -17,6 +17,7 @@
 #include <linux/module.h>
 #include <linux/msi.h>
 #include <linux/of_address.h>
+#include <linux/of_pci.h>
 #include <linux/pci.h>
 #include <linux/pci_regs.h>
 #include <linux/types.h>
@@ -494,7 +495,7 @@ int __init dw_pcie_host_init(struct pcie_port *pp)
 	dw_pci.nr_controllers = 1;
 	dw_pci.private_data = (void **)&pp;
 
-	pci_common_init(&dw_pci);
+	pci_common_init_dev(pp->dev, &dw_pci);
 	pci_assign_unassigned_resources();
 #ifdef CONFIG_PCI_DOMAINS
 	dw_pci.domain++;
@@ -524,13 +525,13 @@ static void dw_pcie_prog_viewport_cfg1(struct pcie_port *pp, u32 busdev)
 	dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1,
 			  PCIE_ATU_VIEWPORT);
 	dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_CFG1, PCIE_ATU_CR1);
-	dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2);
 	dw_pcie_writel_rc(pp, pp->cfg1_base, PCIE_ATU_LOWER_BASE);
 	dw_pcie_writel_rc(pp, (pp->cfg1_base >> 32), PCIE_ATU_UPPER_BASE);
 	dw_pcie_writel_rc(pp, pp->cfg1_base + pp->config.cfg1_size - 1,
 			  PCIE_ATU_LIMIT);
 	dw_pcie_writel_rc(pp, busdev, PCIE_ATU_LOWER_TARGET);
 	dw_pcie_writel_rc(pp, 0, PCIE_ATU_UPPER_TARGET);
+	dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2);
 }
 
 static void dw_pcie_prog_viewport_mem_outbound(struct pcie_port *pp)
@@ -539,7 +540,6 @@ static void dw_pcie_prog_viewport_mem_outbound(struct pcie_port *pp)
 	dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX0,
 			  PCIE_ATU_VIEWPORT);
 	dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_MEM, PCIE_ATU_CR1);
-	dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2);
 	dw_pcie_writel_rc(pp, pp->mem_base, PCIE_ATU_LOWER_BASE);
 	dw_pcie_writel_rc(pp, (pp->mem_base >> 32), PCIE_ATU_UPPER_BASE);
 	dw_pcie_writel_rc(pp, pp->mem_base + pp->config.mem_size - 1,
@@ -547,6 +547,7 @@ static void dw_pcie_prog_viewport_mem_outbound(struct pcie_port *pp)
 	dw_pcie_writel_rc(pp, pp->config.mem_bus_addr, PCIE_ATU_LOWER_TARGET);
 	dw_pcie_writel_rc(pp, upper_32_bits(pp->config.mem_bus_addr),
 			  PCIE_ATU_UPPER_TARGET);
+	dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2);
 }
 
 static void dw_pcie_prog_viewport_io_outbound(struct pcie_port *pp)
@@ -555,7 +556,6 @@ static void dw_pcie_prog_viewport_io_outbound(struct pcie_port *pp)
 	dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | PCIE_ATU_REGION_INDEX1,
 			  PCIE_ATU_VIEWPORT);
 	dw_pcie_writel_rc(pp, PCIE_ATU_TYPE_IO, PCIE_ATU_CR1);
-	dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2);
 	dw_pcie_writel_rc(pp, pp->io_base, PCIE_ATU_LOWER_BASE);
 	dw_pcie_writel_rc(pp, (pp->io_base >> 32), PCIE_ATU_UPPER_BASE);
 	dw_pcie_writel_rc(pp, pp->io_base + pp->config.io_size - 1,
@@ -563,6 +563,7 @@ static void dw_pcie_prog_viewport_io_outbound(struct pcie_port *pp)
 	dw_pcie_writel_rc(pp, pp->config.io_bus_addr, PCIE_ATU_LOWER_TARGET);
 	dw_pcie_writel_rc(pp, upper_32_bits(pp->config.io_bus_addr),
 			  PCIE_ATU_UPPER_TARGET);
+	dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2);
 }
 
 static int dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
@@ -642,7 +643,6 @@ static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
 			int size, u32 *val)
 {
 	struct pcie_port *pp = sys_to_pcie(bus->sysdata);
-	unsigned long flags;
 	int ret;
 
 	if (!pp) {
@@ -655,13 +655,11 @@ static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
 		return PCIBIOS_DEVICE_NOT_FOUND;
 	}
 
-	spin_lock_irqsave(&pp->conf_lock, flags);
 	if (bus->number != pp->root_bus_nr)
 		ret = dw_pcie_rd_other_conf(pp, bus, devfn,
 						where, size, val);
 	else
 		ret = dw_pcie_rd_own_conf(pp, where, size, val);
-	spin_unlock_irqrestore(&pp->conf_lock, flags);
 
 	return ret;
 }
@@ -670,7 +668,6 @@ static int dw_pcie_wr_conf(struct pci_bus *bus, u32 devfn,
 			int where, int size, u32 val)
 {
 	struct pcie_port *pp = sys_to_pcie(bus->sysdata);
-	unsigned long flags;
 	int ret;
 
 	if (!pp) {
@@ -681,13 +678,11 @@ static int dw_pcie_wr_conf(struct pci_bus *bus, u32 devfn,
 	if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0)
 		return PCIBIOS_DEVICE_NOT_FOUND;
 
-	spin_lock_irqsave(&pp->conf_lock, flags);
 	if (bus->number != pp->root_bus_nr)
 		ret = dw_pcie_wr_other_conf(pp, bus, devfn,
 						where, size, val);
 	else
 		ret = dw_pcie_wr_own_conf(pp, where, size, val);
-	spin_unlock_irqrestore(&pp->conf_lock, flags);
 
 	return ret;
 }
@@ -727,7 +722,7 @@ static struct pci_bus *dw_pcie_scan_bus(int nr, struct pci_sys_data *sys)
 
 	if (pp) {
 		pp->root_bus_nr = sys->busnr;
-		bus = pci_scan_root_bus(NULL, sys->busnr, &dw_pcie_ops,
+		bus = pci_scan_root_bus(pp->dev, sys->busnr, &dw_pcie_ops,
 					sys, &sys->resources);
 	} else {
 		bus = NULL;
@@ -740,8 +735,13 @@ static struct pci_bus *dw_pcie_scan_bus(int nr, struct pci_sys_data *sys)
 static int dw_pcie_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
 {
 	struct pcie_port *pp = sys_to_pcie(dev->bus->sysdata);
+	int irq;
+
+	irq = of_irq_parse_and_map_pci(dev, slot, pin);
+	if (!irq)
+		irq = pp->irq;
 
-	return pp->irq;
+	return irq;
 }
 
 static void dw_pcie_add_bus(struct pci_bus *bus)
@@ -768,7 +768,7 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
 	u32 membase;
 	u32 memlimit;
 
-	/* set the number of lines as 4 */
+	/* set the number of lanes */
 	dw_pcie_readl_rc(pp, PCIE_PORT_LINK_CONTROL, &val);
 	val &= ~PORT_LINK_MODE_MASK;
 	switch (pp->lanes) {

drivers/pci/host/pcie-designware.h

@@ -41,7 +41,6 @@ struct pcie_port {
 	void __iomem		*va_cfg1_base;
 	u64			io_base;
 	u64			mem_base;
-	spinlock_t		conf_lock;
 	struct resource		cfg;
 	struct resource		io;
 	struct resource		mem;