Merge 4.18-rc5 into char-misc-next

We want the char-misc fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/admin-guide/kernel-parameters.txt

@@ -4846,3 +4846,8 @@
 	xirc2ps_cs=	[NET,PCMCIA]
 			Format:
 			<irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
+
+	xhci-hcd.quirks		[USB,KNL]
+			A hex value specifying bitmask with supplemental xhci
+			host controller quirks. Meaning of each bit can be
+			consulted in header drivers/usb/host/xhci.h.

Documentation/admin-guide/pm/intel_pstate.rst

@@ -324,8 +324,7 @@ Global Attributes
 
 ``intel_pstate`` exposes several global attributes (files) in ``sysfs`` to
 control its functionality at the system level.  They are located in the
-``/sys/devices/system/cpu/cpufreq/intel_pstate/`` directory and affect all
-CPUs.
+``/sys/devices/system/cpu/intel_pstate/`` directory and affect all CPUs.
 
 Some of them are not present if the ``intel_pstate=per_cpu_perf_limits``
 argument is passed to the kernel in the command line.
@@ -379,6 +378,17 @@ argument is passed to the kernel in the command line.
 	but it affects the maximum possible value of per-policy P-state	limits
 	(see `Interpretation of Policy Attributes`_ below for details).
 
+``hwp_dynamic_boost``
+	This attribute is only present if ``intel_pstate`` works in the
+	`active mode with the HWP feature enabled <Active Mode With HWP_>`_ in
+	the processor.  If set (equal to 1), it causes the minimum P-state limit
+	to be increased dynamically for a short time whenever a task previously
+	waiting on I/O is selected to run on a given logical CPU (the purpose
+	of this mechanism is to improve performance).
+
+	This setting has no effect on logical CPUs whose minimum P-state limit
+	is directly set to the highest non-turbo P-state or above it.
+
 .. _status_attr:
 
 ``status``

Documentation/devicetree/bindings/input/sprd,sc27xx-vibra.txt

@@ -0,0 +1,23 @@
+Spreadtrum SC27xx PMIC Vibrator
+
+Required properties:
+- compatible: should be "sprd,sc2731-vibrator".
+- reg: address of vibrator control register.
+
+Example :
+
+	sc2731_pmic: pmic@0 {
+		compatible = "sprd,sc2731";
+		reg = <0>;
+		spi-max-frequency = <26000000>;
+		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vibrator@eb4 {
+			compatible = "sprd,sc2731-vibrator";
+			reg = <0xeb4>;
+		};
+	};

Documentation/filesystems/Locking

@@ -441,8 +441,6 @@ prototypes:
 	int (*iterate) (struct file *, struct dir_context *);
 	int (*iterate_shared) (struct file *, struct dir_context *);
 	__poll_t (*poll) (struct file *, struct poll_table_struct *);
-	struct wait_queue_head * (*get_poll_head)(struct file *, __poll_t);
-	__poll_t (*poll_mask) (struct file *, __poll_t);
 	long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
 	long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
 	int (*mmap) (struct file *, struct vm_area_struct *);
@@ -473,7 +471,7 @@ prototypes:
 };
 
 locking rules:
-	All except for ->poll_mask may block.
+	All may block.
 
 ->llseek() locking has moved from llseek to the individual llseek
 implementations.  If your fs is not using generic_file_llseek, you
@@ -505,9 +503,6 @@ in sys_read() and friends.
 the lease within the individual filesystem to record the result of the
 operation
 
-->poll_mask can be called with or without the waitqueue lock for the waitqueue
-returned from ->get_poll_head.
-
 --------------------------- dquot_operations -------------------------------
 prototypes:
 	int (*write_dquot) (struct dquot *);

Documentation/filesystems/vfs.txt

@@ -857,8 +857,6 @@ struct file_operations {
 	ssize_t (*write_iter) (struct kiocb *, struct iov_iter *);
 	int (*iterate) (struct file *, struct dir_context *);
 	__poll_t (*poll) (struct file *, struct poll_table_struct *);
-	struct wait_queue_head * (*get_poll_head)(struct file *, __poll_t);
-	__poll_t (*poll_mask) (struct file *, __poll_t);
 	long (*unlocked_ioctl) (struct file *, unsigned int, unsigned long);
 	long (*compat_ioctl) (struct file *, unsigned int, unsigned long);
 	int (*mmap) (struct file *, struct vm_area_struct *);
@@ -903,17 +901,6 @@ otherwise noted.
 	activity on this file and (optionally) go to sleep until there
 	is activity. Called by the select(2) and poll(2) system calls
 
-  get_poll_head: Returns the struct wait_queue_head that callers can
-  wait on.  Callers need to check the returned events using ->poll_mask
-  once woken.  Can return NULL to indicate polling is not supported,
-  or any error code using the ERR_PTR convention to indicate that a
-  grave error occured and ->poll_mask shall not be called.
-
-  poll_mask: return the mask of EPOLL* values describing the file descriptor
-  state.  Called either before going to sleep on the waitqueue returned by
-  get_poll_head, or after it has been woken.  If ->get_poll_head and
-  ->poll_mask are implemented ->poll does not need to be implement.
-
   unlocked_ioctl: called by the ioctl(2) system call.
 
   compat_ioctl: called by the ioctl(2) system call when 32 bit system calls

Documentation/kbuild/kbuild.txt

@@ -50,6 +50,11 @@ LDFLAGS_MODULE
 --------------------------------------------------
 Additional options used for $(LD) when linking modules.
 
+KBUILD_KCONFIG
+--------------------------------------------------
+Set the top-level Kconfig file to the value of this environment
+variable.  The default name is "Kconfig".
+
 KBUILD_VERBOSE
 --------------------------------------------------
 Set the kbuild verbosity. Can be assigned same values as "V=...".
@@ -88,7 +93,8 @@ In most cases the name of the architecture is the same as the
 directory name found in the arch/ directory.
 But some architectures such as x86 and sparc have aliases.
 x86: i386 for 32 bit, x86_64 for 64 bit
-sparc: sparc for 32 bit, sparc64 for 64 bit
+sh: sh for 32 bit, sh64 for 64 bit
+sparc: sparc32 for 32 bit, sparc64 for 64 bit
 
 CROSS_COMPILE
 --------------------------------------------------
@@ -148,15 +154,6 @@ stripped after they are installed.  If INSTALL_MOD_STRIP is '1', then
 the default option --strip-debug will be used.  Otherwise,
 INSTALL_MOD_STRIP value will be used as the options to the strip command.
 
-INSTALL_FW_PATH
---------------------------------------------------
-INSTALL_FW_PATH specifies where to install the firmware blobs.
-The default value is:
-
-    $(INSTALL_MOD_PATH)/lib/firmware
-
-The value can be overridden in which case the default value is ignored.
-
 INSTALL_HDR_PATH
 --------------------------------------------------
 INSTALL_HDR_PATH specifies where to install user space headers when

Documentation/kbuild/kconfig-language.txt

@@ -430,6 +430,12 @@ This sets the config program's title bar if the config program chooses
 to use it. It should be placed at the top of the configuration, before any
 other statement.
 
+'#' Kconfig source file comment:
+
+An unquoted '#' character anywhere in a source file line indicates
+the beginning of a source file comment.  The remainder of that line
+is a comment.
+
 
 Kconfig hints
 -------------

Documentation/kbuild/kconfig.txt

@@ -2,9 +2,9 @@ This file contains some assistance for using "make *config".
 
 Use "make help" to list all of the possible configuration targets.
 
-The xconfig ('qconf') and menuconfig ('mconf') programs also
-have embedded help text.  Be sure to check it for navigation,
-search, and other general help text.
+The xconfig ('qconf'), menuconfig ('mconf'), and nconfig ('nconf')
+programs also have embedded help text.  Be sure to check that for
+navigation, search, and other general help text.
 
 ======================================================================
 General
@@ -17,13 +17,16 @@ this happens, using a previously working .config file and running
 for you, so you may find that you need to see what NEW kernel
 symbols have been introduced.
 
-To see a list of new config symbols when using "make oldconfig", use
+To see a list of new config symbols, use
 
 	cp user/some/old.config .config
 	make listnewconfig
 
 and the config program will list any new symbols, one per line.
 
+Alternatively, you can use the brute force method:
+
+	make oldconfig
 	scripts/diffconfig .config.old .config | less
 
 ______________________________________________________________________
@@ -160,7 +163,7 @@ Searching in menuconfig:
 		This lists all config symbols that contain "hotplug",
 		e.g., HOTPLUG_CPU, MEMORY_HOTPLUG.
 
-	For search help, enter / followed TAB-TAB-TAB (to highlight
+	For search help, enter / followed by TAB-TAB (to highlight
 	<Help>) and Enter.  This will tell you that you can also use
 	regular expressions (regexes) in the search string, so if you
 	are not interested in MEMORY_HOTPLUG, you could try
@@ -202,6 +205,39 @@ Example:
 	make MENUCONFIG_MODE=single_menu menuconfig
 
 
+======================================================================
+nconfig
+--------------------------------------------------
+
+nconfig is an alternate text-based configurator.  It lists function
+keys across the bottom of the terminal (window) that execute commands.
+You can also just use the corresponding numeric key to execute the
+commands unless you are in a data entry window.  E.g., instead of F6
+for Save, you can just press 6.
+
+Use F1 for Global help or F3 for the Short help menu.
+
+Searching in nconfig:
+
+	You can search either in the menu entry "prompt" strings
+	or in the configuration symbols.
+
+	Use / to begin a search through the menu entries.  This does
+	not support regular expressions.  Use <Down> or <Up> for
+	Next hit and Previous hit, respectively.  Use <Esc> to
+	terminate the search mode.
+
+	F8 (SymSearch) searches the configuration symbols for the
+	given string or regular expression (regex).
+
+NCONFIG_MODE
+--------------------------------------------------
+This mode shows all sub-menus in one large tree.
+
+Example:
+	make NCONFIG_MODE=single_menu nconfig
+
+
 ======================================================================
 xconfig
 --------------------------------------------------
@@ -230,8 +266,7 @@ gconfig
 
 Searching in gconfig:
 
-	None (gconfig isn't maintained as well as xconfig or menuconfig);
-	however, gconfig does have a few more viewing choices than
-	xconfig does.
+	There is no search command in gconfig.  However, gconfig does
+	have several different viewing choices, modes, and options.
 
 ###

Documentation/networking/e100.rst

@@ -1,3 +1,4 @@
+==============================================================
 Linux* Base Driver for the Intel(R) PRO/100 Family of Adapters
 ==============================================================
 
@@ -86,83 +87,84 @@ Event Log Message Level:  The driver uses the message level flag to log events
 Additional Configurations
 =========================
 
-  Configuring the Driver on Different Distributions
-  -------------------------------------------------
+Configuring the Driver on Different Distributions
+-------------------------------------------------
 
-  Configuring a network driver to load properly when the system is started is
-  distribution dependent. Typically, the configuration process involves adding
-  an alias line to /etc/modprobe.d/*.conf as well as editing other system
-  startup scripts and/or configuration files.  Many popular Linux
-  distributions ship with tools to make these changes for you. To learn the
-  proper way to configure a network device for your system, refer to your
-  distribution documentation.  If during this process you are asked for the
-  driver or module name, the name for the Linux Base Driver for the Intel
-  PRO/100 Family of Adapters is e100.
+Configuring a network driver to load properly when the system is started
+is distribution dependent.  Typically, the configuration process involves
+adding an alias line to /etc/modprobe.d/*.conf as well as editing other
+system startup scripts and/or configuration files.  Many popular Linux
+distributions ship with tools to make these changes for you.  To learn
+the proper way to configure a network device for your system, refer to
+your distribution documentation.  If during this process you are asked
+for the driver or module name, the name for the Linux Base Driver for
+the Intel PRO/100 Family of Adapters is e100.
 
-  As an example, if you install the e100 driver for two PRO/100 adapters
-  (eth0 and eth1), add the following to a configuration file in /etc/modprobe.d/
+As an example, if you install the e100 driver for two PRO/100 adapters
+(eth0 and eth1), add the following to a configuration file in
+/etc/modprobe.d/::
 
        alias eth0 e100
        alias eth1 e100
 
-  Viewing Link Messages
-  ---------------------
-  In order to see link messages and other Intel driver information on your
-  console, you must set the dmesg level up to six. This can be done by
-  entering the following on the command line before loading the e100 driver::
-
-       dmesg -n 6
+Viewing Link Messages
+---------------------
 
-  If you wish to see all messages issued by the driver, including debug
-  messages, set the dmesg level to eight.
+In order to see link messages and other Intel driver information on your
+console, you must set the dmesg level up to six.  This can be done by
+entering the following on the command line before loading the e100
+driver::
 
-  NOTE: This setting is not saved across reboots.
+       dmesg -n 6
 
+If you wish to see all messages issued by the driver, including debug
+messages, set the dmesg level to eight.
 
-  ethtool
-  -------
+NOTE: This setting is not saved across reboots.
 
-  The driver utilizes the ethtool interface for driver configuration and
-  diagnostics, as well as displaying statistical information.  The ethtool
-  version 1.6 or later is required for this functionality.
+ethtool
+-------
 
-  The latest release of ethtool can be found from
-  https://www.kernel.org/pub/software/network/ethtool/
+The driver utilizes the ethtool interface for driver configuration and
+diagnostics, as well as displaying statistical information.  The ethtool
+version 1.6 or later is required for this functionality.
 
-  Enabling Wake on LAN* (WoL)
-  ---------------------------
-  WoL is provided through the ethtool* utility.  For instructions on enabling
-  WoL with ethtool, refer to the ethtool man page.
+The latest release of ethtool can be found from
+https://www.kernel.org/pub/software/network/ethtool/
 
-  WoL will be enabled on the system during the next shut down or reboot. For
-  this driver version, in order to enable WoL, the e100 driver must be
-  loaded when shutting down or rebooting the system.
+Enabling Wake on LAN* (WoL)
+---------------------------
+WoL is provided through the ethtool* utility.  For instructions on
+enabling WoL with ethtool, refer to the ethtool man page.  WoL will be
+enabled on the system during the next shut down or reboot.  For this
+driver version, in order to enable WoL, the e100 driver must be loaded
+when shutting down or rebooting the system.
 
-  NAPI
-  ----
+NAPI
+----
 
-  NAPI (Rx polling mode) is supported in the e100 driver.
+NAPI (Rx polling mode) is supported in the e100 driver.
 
-  See https://wiki.linuxfoundation.org/networking/napi for more information
-  on NAPI.
+See https://wiki.linuxfoundation.org/networking/napi for more
+information on NAPI.
 
-  Multiple Interfaces on Same Ethernet Broadcast Network
-  ------------------------------------------------------
+Multiple Interfaces on Same Ethernet Broadcast Network
+------------------------------------------------------
 
-  Due to the default ARP behavior on Linux, it is not possible to have
-  one system on two IP networks in the same Ethernet broadcast domain
-  (non-partitioned switch) behave as expected. All Ethernet interfaces
-  will respond to IP traffic for any IP address assigned to the system.
-  This results in unbalanced receive traffic.
+Due to the default ARP behavior on Linux, it is not possible to have one
+system on two IP networks in the same Ethernet broadcast domain
+(non-partitioned switch) behave as expected.  All Ethernet interfaces
+will respond to IP traffic for any IP address assigned to the system.
+This results in unbalanced receive traffic.
 
-  If you have multiple interfaces in a server, either turn on ARP
-  filtering by
+If you have multiple interfaces in a server, either turn on ARP
+filtering by
 
-  (1) entering:: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
-      (this only works if your kernel's version is higher than 2.4.5), or
+(1) entering:: echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
+    (this only works if your kernel's version is higher than 2.4.5), or
 
-  (2) installing the interfaces in separate broadcast domains (either
-      in different switches or in a switch partitioned to VLANs).
+(2) installing the interfaces in separate broadcast domains (either
+    in different switches or in a switch partitioned to VLANs).
 
 
 Support

Documentation/networking/e1000.rst

@@ -1,3 +1,4 @@
+===========================================================
 Linux* Base Driver for Intel(R) Ethernet Network Connection
 ===========================================================
 
@@ -354,57 +355,58 @@ previously mentioned to force the adapter to the same speed and duplex.
 Additional Configurations
 =========================
 
-  Jumbo Frames
-  ------------
-  Jumbo Frames support is enabled by changing the MTU to a value larger than
-  the default of 1500.  Use the ifconfig command to increase the MTU size.
-  For example::
+Jumbo Frames
+------------
+Jumbo Frames support is enabled by changing the MTU to a value larger
+than the default of 1500.  Use the ifconfig command to increase the MTU
+size.  For example::
 
        ifconfig eth<x> mtu 9000 up
 
-  This setting is not saved across reboots.  It can be made permanent if
-  you add::
+This setting is not saved across reboots.  It can be made permanent if
+you add::
 
        MTU=9000
 
-   to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>.  This example
-   applies to the Red Hat distributions; other distributions may store this
-   setting in a different location.
+to the file /etc/sysconfig/network-scripts/ifcfg-eth<x>.  This example
+applies to the Red Hat distributions; other distributions may store this
+setting in a different location.
+
+Notes: Degradation in throughput performance may be observed in some
+Jumbo frames environments.  If this is observed, increasing the
+application's socket buffer size and/or increasing the
+/proc/sys/net/ipv4/tcp_*mem entry values may help.  See the specific
+application manual and /usr/src/linux*/Documentation/
+networking/ip-sysctl.txt for more details.
 
-  Notes:
-  Degradation in throughput performance may be observed in some Jumbo frames
-  environments. If this is observed, increasing the application's socket buffer
-  size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values may help.
-  See the specific application manual and /usr/src/linux*/Documentation/
-  networking/ip-sysctl.txt for more details.
+- The maximum MTU setting for Jumbo Frames is 16110.  This value
+  coincides with the maximum Jumbo Frames size of 16128.
 
-  - The maximum MTU setting for Jumbo Frames is 16110.  This value coincides
-    with the maximum Jumbo Frames size of 16128.
+- Using Jumbo frames at 10 or 100 Mbps is not supported and may result
+  in poor performance or loss of link.
 
-  - Using Jumbo frames at 10 or 100 Mbps is not supported and may result in
-    poor performance or loss of link.
+- Adapters based on the Intel(R) 82542 and 82573V/E controller do not
+  support Jumbo Frames.  These correspond to the following product names:
+  Intel(R) PRO/1000 Gigabit Server Adapter Intel(R) PRO/1000 PM Network
+  Connection
 
-  - Adapters based on the Intel(R) 82542 and 82573V/E controller do not
-    support Jumbo Frames. These correspond to the following product names:
-     Intel(R) PRO/1000 Gigabit Server Adapter
-     Intel(R) PRO/1000 PM Network Connection
+ethtool
+-------
+The driver utilizes the ethtool interface for driver configuration and
+diagnostics, as well as displaying statistical information.  The ethtool
+version 1.6 or later is required for this functionality.
 
-  ethtool
-  -------
-  The driver utilizes the ethtool interface for driver configuration and
-  diagnostics, as well as displaying statistical information.  The ethtool
-  version 1.6 or later is required for this functionality.
+The latest release of ethtool can be found from
+https://www.kernel.org/pub/software/network/ethtool/
 
-  The latest release of ethtool can be found from
-  https://www.kernel.org/pub/software/network/ethtool/
+Enabling Wake on LAN* (WoL)
+---------------------------
+WoL is configured through the ethtool* utility.
 
-  Enabling Wake on LAN* (WoL)
-  ---------------------------
-  WoL is configured through the ethtool* utility.
+WoL will be enabled on the system during the next shut down or reboot.
+For this driver version, in order to enable WoL, the e1000 driver must be
+loaded when shutting down or rebooting the system.
 
-  WoL will be enabled on the system during the next shut down or reboot.
-  For this driver version, in order to enable WoL, the e1000 driver must be
-  loaded when shutting down or rebooting the system.
 
 Support
 =======

Documentation/networking/strparser.txt

@@ -48,7 +48,7 @@ void strp_pause(struct strparser *strp)
      Temporarily pause a stream parser. Message parsing is suspended
      and no new messages are delivered to the upper layer.
 
-void strp_pause(struct strparser *strp)
+void strp_unpause(struct strparser *strp)
 
      Unpause a paused stream parser.
 

Documentation/usb/gadget_configfs.txt

@@ -226,7 +226,7 @@ $ rm configs/<config name>.<number>/<function>
 where <config name>.<number> specify the configuration and <function> is
 a symlink to a function being removed from the configuration, e.g.:
 
-$ rm configfs/c.1/ncm.usb0
+$ rm configs/c.1/ncm.usb0
 
 ...
 ...

MAINTAINERS

@@ -581,7 +581,7 @@ W:	https://www.infradead.org/~dhowells/kafs/
 
 AGPGART DRIVER
 M:	David Airlie <airlied@linux.ie>
-T:	git git://people.freedesktop.org/~airlied/linux (part of drm maint)
+T:	git git://anongit.freedesktop.org/drm/drm
 S:	Maintained
 F:	drivers/char/agp/
 F:	include/linux/agp*
@@ -2971,9 +2971,13 @@ N:	bcm585*
 N:	bcm586*
 N:	bcm88312
 N:	hr2
-F:	arch/arm64/boot/dts/broadcom/ns2*
+N:	stingray
+F:	arch/arm64/boot/dts/broadcom/northstar2/*
+F:	arch/arm64/boot/dts/broadcom/stingray/*
 F:	drivers/clk/bcm/clk-ns*
+F:	drivers/clk/bcm/clk-sr*
 F:	drivers/pinctrl/bcm/pinctrl-ns*
+F:	include/dt-bindings/clock/bcm-sr*
 
 BROADCOM KONA GPIO DRIVER
 M:	Ray Jui <rjui@broadcom.com>
@@ -4456,6 +4460,7 @@ F:	Documentation/blockdev/drbd/
 
 DRIVER CORE, KOBJECTS, DEBUGFS AND SYSFS
 M:	Greg Kroah-Hartman <gregkh@linuxfoundation.org>
+R:	"Rafael J. Wysocki" <rafael@kernel.org>
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core.git
 S:	Supported
 F:	Documentation/kobject.txt
@@ -4626,7 +4631,7 @@ F:	include/uapi/drm/vmwgfx_drm.h
 DRM DRIVERS
 M:	David Airlie <airlied@linux.ie>
 L:	dri-devel@lists.freedesktop.org
-T:	git git://people.freedesktop.org/~airlied/linux
+T:	git git://anongit.freedesktop.org/drm/drm
 B:	https://bugs.freedesktop.org/
 C:	irc://chat.freenode.net/dri-devel
 S:	Maintained
@@ -5677,7 +5682,7 @@ F:	drivers/crypto/caam/
 F:	Documentation/devicetree/bindings/crypto/fsl-sec4.txt
 
 FREESCALE DIU FRAMEBUFFER DRIVER
-M:	Timur Tabi <timur@tabi.org>
+M:	Timur Tabi <timur@kernel.org>
 L:	linux-fbdev@vger.kernel.org
 S:	Maintained
 F:	drivers/video/fbdev/fsl-diu-fb.*
@@ -5777,7 +5782,7 @@ S:	Maintained
 F:	drivers/net/wan/fsl_ucc_hdlc*
 
 FREESCALE QUICC ENGINE UCC UART DRIVER
-M:	Timur Tabi <timur@tabi.org>
+M:	Timur Tabi <timur@kernel.org>
 L:	linuxppc-dev@lists.ozlabs.org
 S:	Maintained
 F:	drivers/tty/serial/ucc_uart.c
@@ -5801,7 +5806,7 @@ F:	drivers/net/ethernet/freescale/fs_enet/
 F:	include/linux/fs_enet_pd.h
 
 FREESCALE SOC SOUND DRIVERS
-M:	Timur Tabi <timur@tabi.org>
+M:	Timur Tabi <timur@kernel.org>
 M:	Nicolin Chen <nicoleotsuka@gmail.com>
 M:	Xiubo Li <Xiubo.Lee@gmail.com>
 R:	Fabio Estevam <fabio.estevam@nxp.com>
@@ -9898,6 +9903,7 @@ M:	Andrew Lunn <andrew@lunn.ch>
 M:	Vivien Didelot <vivien.didelot@savoirfairelinux.com>
 M:	Florian Fainelli <f.fainelli@gmail.com>
 S:	Maintained
+F:	Documentation/devicetree/bindings/net/dsa/
 F:	net/dsa/
 F:	include/net/dsa.h
 F:	include/linux/dsa/
@@ -10224,11 +10230,13 @@ F:	sound/soc/codecs/sgtl5000*
 
 NXP TDA998X DRM DRIVER
 M:	Russell King <linux@armlinux.org.uk>
-S:	Supported
+S:	Maintained
 T:	git git://git.armlinux.org.uk/~rmk/linux-arm.git drm-tda998x-devel
 T:	git git://git.armlinux.org.uk/~rmk/linux-arm.git drm-tda998x-fixes
 F:	drivers/gpu/drm/i2c/tda998x_drv.c
 F:	include/drm/i2c/tda998x.h
+F:	include/dt-bindings/display/tda998x.h
+K:	"nxp,tda998x"
 
 NXP TFA9879 DRIVER
 M:	Peter Rosin <peda@axentia.se>
@@ -11492,6 +11500,15 @@ W:	http://wireless.kernel.org/en/users/Drivers/p54
 S:	Obsolete
 F:	drivers/net/wireless/intersil/prism54/
 
+PROC FILESYSTEM
+R:	Alexey Dobriyan <adobriyan@gmail.com>
+L:	linux-kernel@vger.kernel.org
+L:	linux-fsdevel@vger.kernel.org
+S:	Maintained
+F:	fs/proc/
+F:	include/linux/proc_fs.h
+F:	tools/testing/selftests/proc/
+
 PROC SYSCTL
 M:	"Luis R. Rodriguez" <mcgrof@kernel.org>
 M:	Kees Cook <keescook@chromium.org>
@@ -11824,9 +11841,9 @@ F:  Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
 F:  drivers/cpufreq/qcom-cpufreq-kryo.c
 
 QUALCOMM EMAC GIGABIT ETHERNET DRIVER
-M:	Timur Tabi <timur@codeaurora.org>
+M:	Timur Tabi <timur@kernel.org>
 L:	netdev@vger.kernel.org
-S:	Supported
+S:	Maintained
 F:	drivers/net/ethernet/qualcomm/emac/
 
 QUALCOMM HEXAGON ARCHITECTURE
@@ -11837,7 +11854,7 @@ S:	Supported
 F:	arch/hexagon/
 
 QUALCOMM HIDMA DRIVER
-M:	Sinan Kaya <okaya@codeaurora.org>
+M:	Sinan Kaya <okaya@kernel.org>
 L:	linux-arm-kernel@lists.infradead.org
 L:	linux-arm-msm@vger.kernel.org
 L:	dmaengine@vger.kernel.org

Makefile

@@ -2,7 +2,7 @@
 VERSION = 4
 PATCHLEVEL = 18
 SUBLEVEL = 0
-EXTRAVERSION = -rc2
+EXTRAVERSION = -rc5
 NAME = Merciless Moray
 
 # *DOCUMENTATION*
@@ -353,9 +353,9 @@ CONFIG_SHELL := $(shell if [ -x "$$BASH" ]; then echo $$BASH; \
 	  else if [ -x /bin/bash ]; then echo /bin/bash; \
 	  else echo sh; fi ; fi)
 
-HOST_LFS_CFLAGS := $(shell getconf LFS_CFLAGS)
-HOST_LFS_LDFLAGS := $(shell getconf LFS_LDFLAGS)
-HOST_LFS_LIBS := $(shell getconf LFS_LIBS)
+HOST_LFS_CFLAGS := $(shell getconf LFS_CFLAGS 2>/dev/null)
+HOST_LFS_LDFLAGS := $(shell getconf LFS_LDFLAGS 2>/dev/null)
+HOST_LFS_LIBS := $(shell getconf LFS_LIBS 2>/dev/null)
 
 HOSTCC       = gcc
 HOSTCXX      = g++
@@ -507,11 +507,6 @@ ifeq ($(shell $(CONFIG_SHELL) $(srctree)/scripts/gcc-goto.sh $(CC) $(KBUILD_CFLA
   KBUILD_AFLAGS += -DCC_HAVE_ASM_GOTO
 endif
 
-ifeq ($(shell $(CONFIG_SHELL) $(srctree)/scripts/cc-can-link.sh $(CC)), y)
-  CC_CAN_LINK := y
-  export CC_CAN_LINK
-endif
-
 # The expansion should be delayed until arch/$(SRCARCH)/Makefile is included.
 # Some architectures define CROSS_COMPILE in arch/$(SRCARCH)/Makefile.
 # CC_VERSION_TEXT is referenced from Kconfig (so it needs export),
@@ -1717,6 +1712,6 @@ endif	# skip-makefile
 PHONY += FORCE
 FORCE:
 
-# Declare the contents of the .PHONY variable as phony.  We keep that
+# Declare the contents of the PHONY variable as phony.  We keep that
 # information in a variable so we can use it in if_changed and friends.
 .PHONY: $(PHONY)

arch/arm/Kconfig

@@ -1245,8 +1245,14 @@ config PCI
 	  VESA. If you have PCI, say Y, otherwise N.
 
 config PCI_DOMAINS
-	bool
+	bool "Support for multiple PCI domains"
 	depends on PCI
+	help
+	  Enable PCI domains kernel management. Say Y if your machine
+	  has a PCI bus hierarchy that requires more than one PCI
+	  domain (aka segment) to be correctly managed. Say N otherwise.
+
+	  If you don't know what to do here, say N.
 
 config PCI_DOMAINS_GENERIC
 	def_bool PCI_DOMAINS

arch/arm/boot/dts/am335x-bone-common.dtsi

@@ -168,7 +168,6 @@
 			AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_dat3.mmc0_dat3 */
 			AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_cmd.mmc0_cmd */
 			AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0)	/* mmc0_clk.mmc0_clk */
-			AM33XX_IOPAD(0x9a0, PIN_INPUT | MUX_MODE4)		/* mcasp0_aclkr.mmc0_sdwp */
 		>;
 	};
 

arch/arm/boot/dts/am3517.dtsi

@@ -39,6 +39,8 @@
 			ti,davinci-ctrl-ram-size = <0x2000>;
 			ti,davinci-rmii-en = /bits/ 8 <1>;
 			local-mac-address = [ 00 00 00 00 00 00 ];
+			clocks = <&emac_ick>;
+			clock-names = "ick";
 		};
 
 		davinci_mdio: ethernet@5c030000 {
@@ -49,6 +51,8 @@
 			bus_freq = <1000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&emac_fck>;
+			clock-names = "fck";
 		};
 
 		uart4: serial@4809e000 {
@@ -87,6 +91,11 @@
 	};
 };
 
+/* Table Table 5-79 of the TRM shows 480ab000 is reserved */
+&usb_otg_hs {
+	status = "disabled";
+};
+
 &iva {
 	status = "disabled";
 };

arch/arm/boot/dts/am437x-sk-evm.dts

@@ -610,6 +610,8 @@
 
 		touchscreen-size-x = <480>;
 		touchscreen-size-y = <272>;
+
+		wakeup-source;
 	};
 
 	tlv320aic3106: tlv320aic3106@1b {

arch/arm/boot/dts/armada-385-synology-ds116.dts

@@ -139,7 +139,7 @@
 					      3700 5
 					      3900 6
 					      4000 7>;
-			cooling-cells = <2>;
+			#cooling-cells = <2>;
 		};
 
 		gpio-leds {

arch/arm/boot/dts/armada-38x.dtsi

@@ -547,7 +547,7 @@
 
 			thermal: thermal@e8078 {
 				compatible = "marvell,armada380-thermal";
-				reg = <0xe4078 0x4>, <0xe4074 0x4>;
+				reg = <0xe4078 0x4>, <0xe4070 0x8>;
 				status = "okay";
 			};
 

arch/arm/boot/dts/bcm-cygnus.dtsi

@@ -216,7 +216,7 @@
 			reg = <0x18008000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};
@@ -245,7 +245,7 @@
 			reg = <0x1800b000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};
@@ -256,7 +256,7 @@
 
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 
 			linux,pci-domain = <0>;
 
@@ -278,10 +278,10 @@
 				compatible = "brcm,iproc-msi";
 				msi-controller;
 				interrupt-parent = <&gic>;
-				interrupts = <GIC_SPI 96 IRQ_TYPE_NONE>,
-					     <GIC_SPI 97 IRQ_TYPE_NONE>,
-					     <GIC_SPI 98 IRQ_TYPE_NONE>,
-					     <GIC_SPI 99 IRQ_TYPE_NONE>;
+				interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
@@ -291,7 +291,7 @@
 
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0>;
-			interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
+			interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
 
 			linux,pci-domain = <1>;
 
@@ -313,10 +313,10 @@
 				compatible = "brcm,iproc-msi";
 				msi-controller;
 				interrupt-parent = <&gic>;
-				interrupts = <GIC_SPI 102 IRQ_TYPE_NONE>,
-					     <GIC_SPI 103 IRQ_TYPE_NONE>,
-					     <GIC_SPI 104 IRQ_TYPE_NONE>,
-					     <GIC_SPI 105 IRQ_TYPE_NONE>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 

arch/arm/boot/dts/bcm-hr2.dtsi

@@ -264,7 +264,7 @@
 			reg = <0x38000 0x50>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 95 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 		};
 
@@ -279,7 +279,7 @@
 			reg = <0x3b000 0x50>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 96 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 		};
 	};
@@ -300,7 +300,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 186 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <0>;
 
@@ -322,10 +322,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 182 IRQ_TYPE_NONE>,
-				     <GIC_SPI 183 IRQ_TYPE_NONE>,
-				     <GIC_SPI 184 IRQ_TYPE_NONE>,
-				     <GIC_SPI 185 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};
@@ -336,7 +336,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 192 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <1>;
 
@@ -358,10 +358,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 188 IRQ_TYPE_NONE>,
-				     <GIC_SPI 189 IRQ_TYPE_NONE>,
-				     <GIC_SPI 190 IRQ_TYPE_NONE>,
-				     <GIC_SPI 191 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};

arch/arm/boot/dts/bcm-nsp.dtsi

@@ -391,7 +391,7 @@
 			reg = <0x38000 0x50>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			dma-coherent;
 			status = "disabled";
@@ -496,7 +496,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <0>;
 
@@ -519,10 +519,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 127 IRQ_TYPE_NONE>,
-				     <GIC_SPI 128 IRQ_TYPE_NONE>,
-				     <GIC_SPI 129 IRQ_TYPE_NONE>,
-				     <GIC_SPI 130 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};
@@ -533,7 +533,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <1>;
 
@@ -556,10 +556,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 133 IRQ_TYPE_NONE>,
-				     <GIC_SPI 134 IRQ_TYPE_NONE>,
-				     <GIC_SPI 135 IRQ_TYPE_NONE>,
-				     <GIC_SPI 136 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};
@@ -570,7 +570,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <2>;
 
@@ -593,10 +593,10 @@
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
-			interrupts = <GIC_SPI 139 IRQ_TYPE_NONE>,
-				     <GIC_SPI 140 IRQ_TYPE_NONE>,
-				     <GIC_SPI 141 IRQ_TYPE_NONE>,
-				     <GIC_SPI 142 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
 			brcm,pcie-msi-inten;
 		};
 	};

arch/arm/boot/dts/bcm5301x.dtsi

@@ -365,7 +365,7 @@
 	i2c0: i2c@18009000 {
 		compatible = "brcm,iproc-i2c";
 		reg = <0x18009000 0x50>;
-		interrupts = <GIC_SPI 121 IRQ_TYPE_NONE>;
+		interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		clock-frequency = <100000>;

arch/arm/boot/dts/da850.dtsi

@@ -549,11 +549,7 @@
 			gpio-controller;
 			#gpio-cells = <2>;
 			reg = <0x226000 0x1000>;
-			interrupts = <42 IRQ_TYPE_EDGE_BOTH
-				43 IRQ_TYPE_EDGE_BOTH 44 IRQ_TYPE_EDGE_BOTH
-				45 IRQ_TYPE_EDGE_BOTH 46 IRQ_TYPE_EDGE_BOTH
-				47 IRQ_TYPE_EDGE_BOTH 48 IRQ_TYPE_EDGE_BOTH
-				49 IRQ_TYPE_EDGE_BOTH 50 IRQ_TYPE_EDGE_BOTH>;
+			interrupts = <42 43 44 45 46 47 48 49 50>;
 			ti,ngpio = <144>;
 			ti,davinci-gpio-unbanked = <0>;
 			status = "disabled";

arch/arm/boot/dts/dra7.dtsi

@@ -1580,7 +1580,6 @@
 				dr_mode = "otg";
 				snps,dis_u3_susphy_quirk;
 				snps,dis_u2_susphy_quirk;
-				snps,dis_metastability_quirk;
 			};
 		};
 
@@ -1608,6 +1607,7 @@
 				dr_mode = "otg";
 				snps,dis_u3_susphy_quirk;
 				snps,dis_u2_susphy_quirk;
+				snps,dis_metastability_quirk;
 			};
 		};
 

arch/arm/boot/dts/imx51-zii-rdu1.dts

@@ -770,7 +770,7 @@
 
 	pinctrl_ts: tsgrp {
 		fsl,pins = <
-			MX51_PAD_CSI1_D8__GPIO3_12		0x85
+			MX51_PAD_CSI1_D8__GPIO3_12		0x04
 			MX51_PAD_CSI1_D9__GPIO3_13		0x85
 		>;
 	};

arch/arm/boot/dts/imx6q.dtsi

@@ -90,7 +90,7 @@
 					clocks = <&clks IMX6Q_CLK_ECSPI5>,
 						 <&clks IMX6Q_CLK_ECSPI5>;
 					clock-names = "ipg", "per";
-					dmas = <&sdma 11 7 1>, <&sdma 12 7 2>;
+					dmas = <&sdma 11 8 1>, <&sdma 12 8 2>;
 					dma-names = "rx", "tx";
 					status = "disabled";
 				};

arch/arm/boot/dts/imx6sx.dtsi

@@ -1344,7 +1344,7 @@
 			ranges = <0x81000000 0 0          0x08f80000 0 0x00010000 /* downstream I/O */
 				  0x82000000 0 0x08000000 0x08000000 0 0x00f00000>; /* non-prefetchable memory */
 			num-lanes = <1>;
-			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;

arch/arm/boot/dts/socfpga.dtsi

@@ -748,13 +748,13 @@
 		nand0: nand@ff900000 {
 			#address-cells = <0x1>;
 			#size-cells = <0x1>;
-			compatible = "denali,denali-nand-dt";
+			compatible = "altr,socfpga-denali-nand";
 			reg = <0xff900000 0x100000>,
 			      <0xffb80000 0x10000>;
 			reg-names = "nand_data", "denali_reg";
 			interrupts = <0x0 0x90 0x4>;
 			dma-mask = <0xffffffff>;
-			clocks = <&nand_clk>;
+			clocks = <&nand_x_clk>;
 			status = "disabled";
 		};
 

arch/arm/boot/dts/socfpga_arria10.dtsi

@@ -593,8 +593,7 @@
 			#size-cells = <0>;
 			reg = <0xffda5000 0x100>;
 			interrupts = <0 102 4>;
-			num-chipselect = <4>;
-			bus-num = <0>;
+			num-cs = <4>;
 			/*32bit_access;*/
 			tx-dma-channel = <&pdma 16>;
 			rx-dma-channel = <&pdma 17>;
@@ -633,7 +632,7 @@
 		nand: nand@ffb90000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
-			compatible = "denali,denali-nand-dt", "altr,socfpga-denali-nand";
+			compatible = "altr,socfpga-denali-nand";
 			reg = <0xffb90000 0x72000>,
 			      <0xffb80000 0x10000>;
 			reg-names = "nand_data", "denali_reg";

arch/arm/common/Makefile

@@ -10,7 +10,7 @@ obj-$(CONFIG_DMABOUNCE)		+= dmabounce.o
 obj-$(CONFIG_SHARP_LOCOMO)	+= locomo.o
 obj-$(CONFIG_SHARP_PARAM)	+= sharpsl_param.o
 obj-$(CONFIG_SHARP_SCOOP)	+= scoop.o
-obj-$(CONFIG_SMP)		+= secure_cntvoff.o
+obj-$(CONFIG_CPU_V7)		+= secure_cntvoff.o
 obj-$(CONFIG_PCI_HOST_ITE8152)  += it8152.o
 obj-$(CONFIG_MCPM)		+= mcpm_head.o mcpm_entry.o mcpm_platsmp.o vlock.o
 CFLAGS_REMOVE_mcpm_entry.o	= -pg

arch/arm/configs/imx_v4_v5_defconfig

@@ -141,9 +141,11 @@ CONFIG_USB_STORAGE=y
 CONFIG_USB_CHIPIDEA=y
 CONFIG_USB_CHIPIDEA_UDC=y
 CONFIG_USB_CHIPIDEA_HOST=y
+CONFIG_USB_CHIPIDEA_ULPI=y
 CONFIG_NOP_USB_XCEIV=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_ETH=m
+CONFIG_USB_ULPI_BUS=y
 CONFIG_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_PLTFM=y

arch/arm/configs/imx_v6_v7_defconfig

@@ -302,6 +302,7 @@ CONFIG_USB_STORAGE=y
 CONFIG_USB_CHIPIDEA=y
 CONFIG_USB_CHIPIDEA_UDC=y
 CONFIG_USB_CHIPIDEA_HOST=y
+CONFIG_USB_CHIPIDEA_ULPI=y
 CONFIG_USB_SERIAL=m
 CONFIG_USB_SERIAL_GENERIC=y
 CONFIG_USB_SERIAL_FTDI_SIO=m
@@ -338,6 +339,7 @@ CONFIG_USB_GADGETFS=m
 CONFIG_USB_FUNCTIONFS=m
 CONFIG_USB_MASS_STORAGE=m
 CONFIG_USB_G_SERIAL=m
+CONFIG_USB_ULPI_BUS=y
 CONFIG_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_PLTFM=y

arch/arm/configs/multi_v7_defconfig

@@ -1,5 +1,4 @@
 CONFIG_SYSVIPC=y
-CONFIG_FHANDLE=y
 CONFIG_NO_HZ=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_CGROUPS=y
@@ -10,20 +9,10 @@ CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_CMDLINE_PARTITION=y
-CONFIG_ARCH_MULTI_V7=y
-# CONFIG_ARCH_MULTI_V5 is not set
-# CONFIG_ARCH_MULTI_V4 is not set
 CONFIG_ARCH_VIRT=y
 CONFIG_ARCH_ALPINE=y
 CONFIG_ARCH_ARTPEC=y
 CONFIG_MACH_ARTPEC6=y
-CONFIG_ARCH_MVEBU=y
-CONFIG_MACH_ARMADA_370=y
-CONFIG_MACH_ARMADA_375=y
-CONFIG_MACH_ARMADA_38X=y
-CONFIG_MACH_ARMADA_39X=y
-CONFIG_MACH_ARMADA_XP=y
-CONFIG_MACH_DOVE=y
 CONFIG_ARCH_AT91=y
 CONFIG_SOC_SAMA5D2=y
 CONFIG_SOC_SAMA5D3=y
@@ -32,9 +21,9 @@ CONFIG_ARCH_BCM=y
 CONFIG_ARCH_BCM_CYGNUS=y
 CONFIG_ARCH_BCM_HR2=y
 CONFIG_ARCH_BCM_NSP=y
-CONFIG_ARCH_BCM_21664=y
-CONFIG_ARCH_BCM_281XX=y
 CONFIG_ARCH_BCM_5301X=y
+CONFIG_ARCH_BCM_281XX=y
+CONFIG_ARCH_BCM_21664=y
 CONFIG_ARCH_BCM2835=y
 CONFIG_ARCH_BCM_63XX=y
 CONFIG_ARCH_BRCMSTB=y
@@ -43,14 +32,14 @@ CONFIG_MACH_BERLIN_BG2=y
 CONFIG_MACH_BERLIN_BG2CD=y
 CONFIG_MACH_BERLIN_BG2Q=y
 CONFIG_ARCH_DIGICOLOR=y
+CONFIG_ARCH_EXYNOS=y
+CONFIG_EXYNOS5420_MCPM=y
 CONFIG_ARCH_HIGHBANK=y
 CONFIG_ARCH_HISI=y
 CONFIG_ARCH_HI3xxx=y
-CONFIG_ARCH_HIX5HD2=y
 CONFIG_ARCH_HIP01=y
 CONFIG_ARCH_HIP04=y
-CONFIG_ARCH_KEYSTONE=y
-CONFIG_ARCH_MESON=y
+CONFIG_ARCH_HIX5HD2=y
 CONFIG_ARCH_MXC=y
 CONFIG_SOC_IMX50=y
 CONFIG_SOC_IMX51=y
@@ -60,29 +49,30 @@ CONFIG_SOC_IMX6SL=y
 CONFIG_SOC_IMX6SX=y
 CONFIG_SOC_IMX6UL=y
 CONFIG_SOC_IMX7D=y
-CONFIG_SOC_VF610=y
 CONFIG_SOC_LS1021A=y
+CONFIG_SOC_VF610=y
+CONFIG_ARCH_KEYSTONE=y
+CONFIG_ARCH_MEDIATEK=y
+CONFIG_ARCH_MESON=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_MACH_ARMADA_370=y
+CONFIG_MACH_ARMADA_375=y
+CONFIG_MACH_ARMADA_38X=y
+CONFIG_MACH_ARMADA_39X=y
+CONFIG_MACH_ARMADA_XP=y
+CONFIG_MACH_DOVE=y
 CONFIG_ARCH_OMAP3=y
 CONFIG_ARCH_OMAP4=y
 CONFIG_SOC_OMAP5=y
 CONFIG_SOC_AM33XX=y
 CONFIG_SOC_AM43XX=y
 CONFIG_SOC_DRA7XX=y
+CONFIG_ARCH_SIRF=y
 CONFIG_ARCH_QCOM=y
-CONFIG_ARCH_MEDIATEK=y
 CONFIG_ARCH_MSM8X60=y
 CONFIG_ARCH_MSM8960=y
 CONFIG_ARCH_MSM8974=y
 CONFIG_ARCH_ROCKCHIP=y
-CONFIG_ARCH_SOCFPGA=y
-CONFIG_PLAT_SPEAR=y
-CONFIG_ARCH_SPEAR13XX=y
-CONFIG_MACH_SPEAR1310=y
-CONFIG_MACH_SPEAR1340=y
-CONFIG_ARCH_STI=y
-CONFIG_ARCH_STM32=y
-CONFIG_ARCH_EXYNOS=y
-CONFIG_EXYNOS5420_MCPM=y
 CONFIG_ARCH_RENESAS=y
 CONFIG_ARCH_EMEV2=y
 CONFIG_ARCH_R7S72100=y
@@ -99,40 +89,33 @@ CONFIG_ARCH_R8A7792=y
 CONFIG_ARCH_R8A7793=y
 CONFIG_ARCH_R8A7794=y
 CONFIG_ARCH_SH73A0=y
+CONFIG_ARCH_SOCFPGA=y
+CONFIG_PLAT_SPEAR=y
+CONFIG_ARCH_SPEAR13XX=y
+CONFIG_MACH_SPEAR1310=y
+CONFIG_MACH_SPEAR1340=y
+CONFIG_ARCH_STI=y
+CONFIG_ARCH_STM32=y
 CONFIG_ARCH_SUNXI=y
-CONFIG_ARCH_SIRF=y
 CONFIG_ARCH_TEGRA=y
-CONFIG_ARCH_TEGRA_2x_SOC=y
-CONFIG_ARCH_TEGRA_3x_SOC=y
-CONFIG_ARCH_TEGRA_114_SOC=y
-CONFIG_ARCH_TEGRA_124_SOC=y
 CONFIG_ARCH_UNIPHIER=y
 CONFIG_ARCH_U8500=y
-CONFIG_MACH_HREFV60=y
-CONFIG_MACH_SNOWBALL=y
 CONFIG_ARCH_VEXPRESS=y
 CONFIG_ARCH_VEXPRESS_TC2_PM=y
 CONFIG_ARCH_WM8850=y
 CONFIG_ARCH_ZYNQ=y
-CONFIG_TRUSTED_FOUNDATIONS=y
-CONFIG_PCI=y
-CONFIG_PCI_HOST_GENERIC=y
-CONFIG_PCI_DRA7XX=y
-CONFIG_PCI_DRA7XX_EP=y
-CONFIG_PCI_KEYSTONE=y
-CONFIG_PCI_MSI=y
+CONFIG_PCIEPORTBUS=y
 CONFIG_PCI_MVEBU=y
 CONFIG_PCI_TEGRA=y
 CONFIG_PCI_RCAR_GEN2=y
 CONFIG_PCIE_RCAR=y
-CONFIG_PCIEPORTBUS=y
+CONFIG_PCI_DRA7XX_EP=y
+CONFIG_PCI_KEYSTONE=y
 CONFIG_PCI_ENDPOINT=y
 CONFIG_PCI_ENDPOINT_CONFIGFS=y
 CONFIG_PCI_EPF_TEST=m
 CONFIG_SMP=y
 CONFIG_NR_CPUS=16
-CONFIG_HIGHPTE=y
-CONFIG_CMA=y
 CONFIG_SECCOMP=y
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
@@ -145,14 +128,14 @@ CONFIG_CPU_FREQ_GOV_POWERSAVE=m
 CONFIG_CPU_FREQ_GOV_USERSPACE=m
 CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
 CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
+CONFIG_CPUFREQ_DT=y
 CONFIG_ARM_IMX6Q_CPUFREQ=y
 CONFIG_QORIQ_CPUFREQ=y
 CONFIG_CPU_IDLE=y
 CONFIG_ARM_CPUIDLE=y
-CONFIG_NEON=y
-CONFIG_KERNEL_MODE_NEON=y
 CONFIG_ARM_ZYNQ_CPUIDLE=y
 CONFIG_ARM_EXYNOS_CPUIDLE=y
+CONFIG_KERNEL_MODE_NEON=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -170,23 +153,13 @@ CONFIG_IPV6_MIP6=m
 CONFIG_IPV6_TUNNEL=m
 CONFIG_IPV6_MULTIPLE_TABLES=y
 CONFIG_NET_DSA=m
-CONFIG_NET_SWITCHDEV=y
 CONFIG_CAN=y
-CONFIG_CAN_RAW=y
-CONFIG_CAN_BCM=y
-CONFIG_CAN_DEV=y
 CONFIG_CAN_AT91=m
 CONFIG_CAN_FLEXCAN=m
-CONFIG_CAN_RCAR=m
+CONFIG_CAN_SUN4I=y
 CONFIG_CAN_XILINXCAN=y
+CONFIG_CAN_RCAR=m
 CONFIG_CAN_MCP251X=y
-CONFIG_NET_DSA_BCM_SF2=m
-CONFIG_B53=m
-CONFIG_B53_SPI_DRIVER=m
-CONFIG_B53_MDIO_DRIVER=m
-CONFIG_B53_MMAP_DRIVER=m
-CONFIG_B53_SRAB_DRIVER=m
-CONFIG_CAN_SUN4I=y
 CONFIG_BT=m
 CONFIG_BT_HCIUART=m
 CONFIG_BT_HCIUART_BCM=y
@@ -199,11 +172,9 @@ CONFIG_RFKILL_INPUT=y
 CONFIG_RFKILL_GPIO=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_DMA_CMA=y
 CONFIG_CMA_SIZE_MBYTES=64
 CONFIG_OMAP_OCP2SCP=y
 CONFIG_SIMPLE_PM_BUS=y
-CONFIG_SUNXI_RSB=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -236,7 +207,6 @@ CONFIG_PCI_ENDPOINT_TEST=m
 CONFIG_EEPROM_AT24=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_BLK_DEV_SR=y
-CONFIG_SCSI_MULTI_LUN=y
 CONFIG_ATA=y
 CONFIG_SATA_AHCI=y
 CONFIG_SATA_AHCI_PLATFORM=y
@@ -251,14 +221,20 @@ CONFIG_SATA_MV=y
 CONFIG_SATA_RCAR=y
 CONFIG_NETDEVICES=y
 CONFIG_VIRTIO_NET=y
-CONFIG_HIX5HD2_GMAC=y
+CONFIG_B53_SPI_DRIVER=m
+CONFIG_B53_MDIO_DRIVER=m
+CONFIG_B53_MMAP_DRIVER=m
+CONFIG_B53_SRAB_DRIVER=m
+CONFIG_NET_DSA_BCM_SF2=m
 CONFIG_SUN4I_EMAC=y
-CONFIG_MACB=y
 CONFIG_BCMGENET=m
 CONFIG_BGMAC_BCMA=y
 CONFIG_SYSTEMPORT=m
+CONFIG_MACB=y
 CONFIG_NET_CALXEDA_XGMAC=y
 CONFIG_GIANFAR=y
+CONFIG_HIX5HD2_GMAC=y
+CONFIG_E1000E=y
 CONFIG_IGB=y
 CONFIG_MV643XX_ETH=y
 CONFIG_MVNETA=y
@@ -268,19 +244,17 @@ CONFIG_R8169=y
 CONFIG_SH_ETH=y
 CONFIG_SMSC911X=y
 CONFIG_STMMAC_ETH=y
-CONFIG_STMMAC_PLATFORM=y
 CONFIG_DWMAC_DWC_QOS_ETH=y
 CONFIG_TI_CPSW=y
 CONFIG_XILINX_EMACLITE=y
 CONFIG_AT803X_PHY=y
-CONFIG_MARVELL_PHY=y
-CONFIG_SMSC_PHY=y
 CONFIG_BROADCOM_PHY=y
 CONFIG_ICPLUS_PHY=y
-CONFIG_REALTEK_PHY=y
+CONFIG_MARVELL_PHY=y
 CONFIG_MICREL_PHY=y
-CONFIG_FIXED_PHY=y
+CONFIG_REALTEK_PHY=y
 CONFIG_ROCKCHIP_PHY=y
+CONFIG_SMSC_PHY=y
 CONFIG_USB_PEGASUS=y
 CONFIG_USB_RTL8152=m
 CONFIG_USB_LAN78XX=m
@@ -288,29 +262,29 @@ CONFIG_USB_USBNET=y
 CONFIG_USB_NET_SMSC75XX=y
 CONFIG_USB_NET_SMSC95XX=y
 CONFIG_BRCMFMAC=m
-CONFIG_RT2X00=m
-CONFIG_RT2800USB=m
 CONFIG_MWIFIEX=m
 CONFIG_MWIFIEX_SDIO=m
+CONFIG_RT2X00=m
+CONFIG_RT2800USB=m
 CONFIG_INPUT_JOYDEV=y
 CONFIG_INPUT_EVDEV=y
 CONFIG_KEYBOARD_QT1070=m
 CONFIG_KEYBOARD_GPIO=y
 CONFIG_KEYBOARD_TEGRA=y
-CONFIG_KEYBOARD_SPEAR=y
+CONFIG_KEYBOARD_SAMSUNG=m
 CONFIG_KEYBOARD_ST_KEYSCAN=y
+CONFIG_KEYBOARD_SPEAR=y
 CONFIG_KEYBOARD_CROS_EC=m
-CONFIG_KEYBOARD_SAMSUNG=m
 CONFIG_MOUSE_PS2_ELANTECH=y
 CONFIG_MOUSE_CYAPA=m
 CONFIG_MOUSE_ELAN_I2C=y
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ATMEL_MXT=m
 CONFIG_TOUCHSCREEN_MMS114=m
+CONFIG_TOUCHSCREEN_WM97XX=m
 CONFIG_TOUCHSCREEN_ST1232=m
 CONFIG_TOUCHSCREEN_STMPE=y
 CONFIG_TOUCHSCREEN_SUN4I=y
-CONFIG_TOUCHSCREEN_WM97XX=m
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_MAX77693_HAPTIC=m
 CONFIG_INPUT_MAX8997_HAPTIC=m
@@ -327,13 +301,12 @@ CONFIG_SERIAL_8250_DW=y
 CONFIG_SERIAL_8250_EM=y
 CONFIG_SERIAL_8250_MT6577=y
 CONFIG_SERIAL_8250_UNIPHIER=y
+CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 CONFIG_SERIAL_ATMEL=y
 CONFIG_SERIAL_ATMEL_CONSOLE=y
 CONFIG_SERIAL_ATMEL_TTYAT=y
-CONFIG_SERIAL_BCM63XX=y
-CONFIG_SERIAL_BCM63XX_CONSOLE=y
 CONFIG_SERIAL_MESON=y
 CONFIG_SERIAL_MESON_CONSOLE=y
 CONFIG_SERIAL_SAMSUNG=y
@@ -345,15 +318,14 @@ CONFIG_SERIAL_IMX=y
 CONFIG_SERIAL_IMX_CONSOLE=y
 CONFIG_SERIAL_SH_SCI=y
 CONFIG_SERIAL_SH_SCI_NR_UARTS=20
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
-CONFIG_SERIAL_SH_SCI_DMA=y
 CONFIG_SERIAL_MSM=y
 CONFIG_SERIAL_MSM_CONSOLE=y
 CONFIG_SERIAL_VT8500=y
 CONFIG_SERIAL_VT8500_CONSOLE=y
-CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_SERIAL_OMAP=y
 CONFIG_SERIAL_OMAP_CONSOLE=y
+CONFIG_SERIAL_BCM63XX=y
+CONFIG_SERIAL_BCM63XX_CONSOLE=y
 CONFIG_SERIAL_XILINX_PS_UART=y
 CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
 CONFIG_SERIAL_FSL_LPUART=y
@@ -365,12 +337,10 @@ CONFIG_SERIAL_ST_ASC_CONSOLE=y
 CONFIG_SERIAL_STM32=y
 CONFIG_SERIAL_STM32_CONSOLE=y
 CONFIG_SERIAL_DEV_BUS=y
-CONFIG_HVC_DRIVER=y
 CONFIG_VIRTIO_CONSOLE=y
+CONFIG_HW_RANDOM=y
+CONFIG_HW_RANDOM_ST=y
 CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_DAVINCI=y
-CONFIG_I2C_MESON=y
-CONFIG_I2C_MUX=y
 CONFIG_I2C_ARB_GPIO_CHALLENGE=m
 CONFIG_I2C_MUX_PCA954x=y
 CONFIG_I2C_MUX_PINCTRL=y
@@ -378,12 +348,13 @@ CONFIG_I2C_DEMUX_PINCTRL=y
 CONFIG_I2C_AT91=m
 CONFIG_I2C_BCM2835=y
 CONFIG_I2C_CADENCE=y
+CONFIG_I2C_DAVINCI=y
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 CONFIG_I2C_DIGICOLOR=m
 CONFIG_I2C_EMEV2=m
 CONFIG_I2C_GPIO=m
-CONFIG_I2C_EXYNOS5=y
 CONFIG_I2C_IMX=y
+CONFIG_I2C_MESON=y
 CONFIG_I2C_MV64XXX=y
 CONFIG_I2C_RIIC=y
 CONFIG_I2C_RK3X=y
@@ -427,7 +398,6 @@ CONFIG_SPI_SPIDEV=y
 CONFIG_SPMI=y
 CONFIG_PINCTRL_AS3722=y
 CONFIG_PINCTRL_PALMAS=y
-CONFIG_PINCTRL_BCM2835=y
 CONFIG_PINCTRL_APQ8064=y
 CONFIG_PINCTRL_APQ8084=y
 CONFIG_PINCTRL_IPQ8064=y
@@ -437,25 +407,33 @@ CONFIG_PINCTRL_MSM8X74=y
 CONFIG_PINCTRL_MSM8916=y
 CONFIG_PINCTRL_QCOM_SPMI_PMIC=y
 CONFIG_PINCTRL_QCOM_SSBI_PMIC=y
-CONFIG_GPIO_GENERIC_PLATFORM=y
 CONFIG_GPIO_DAVINCI=y
 CONFIG_GPIO_DWAPB=y
 CONFIG_GPIO_EM=y
 CONFIG_GPIO_RCAR=y
+CONFIG_GPIO_SYSCON=y
 CONFIG_GPIO_UNIPHIER=y
 CONFIG_GPIO_XILINX=y
 CONFIG_GPIO_ZYNQ=y
 CONFIG_GPIO_PCA953X=y
 CONFIG_GPIO_PCA953X_IRQ=y
 CONFIG_GPIO_PCF857X=y
-CONFIG_GPIO_TWL4030=y
 CONFIG_GPIO_PALMAS=y
-CONFIG_GPIO_SYSCON=y
 CONFIG_GPIO_TPS6586X=y
 CONFIG_GPIO_TPS65910=y
+CONFIG_GPIO_TWL4030=y
+CONFIG_POWER_AVS=y
+CONFIG_ROCKCHIP_IODOMAIN=y
+CONFIG_POWER_RESET_AS3722=y
+CONFIG_POWER_RESET_GPIO=y
+CONFIG_POWER_RESET_GPIO_RESTART=y
+CONFIG_POWER_RESET_ST=y
+CONFIG_POWER_RESET_KEYSTONE=y
+CONFIG_POWER_RESET_RMOBILE=y
 CONFIG_BATTERY_ACT8945A=y
 CONFIG_BATTERY_CPCAP=m
 CONFIG_BATTERY_SBS=y
+CONFIG_AXP20X_POWER=m
 CONFIG_BATTERY_MAX17040=m
 CONFIG_BATTERY_MAX17042=m
 CONFIG_CHARGER_CPCAP=m
@@ -464,15 +442,6 @@ CONFIG_CHARGER_MAX77693=m
 CONFIG_CHARGER_MAX8997=m
 CONFIG_CHARGER_MAX8998=m
 CONFIG_CHARGER_TPS65090=y
-CONFIG_AXP20X_POWER=m
-CONFIG_POWER_RESET_AS3722=y
-CONFIG_POWER_RESET_GPIO=y
-CONFIG_POWER_RESET_GPIO_RESTART=y
-CONFIG_POWER_RESET_KEYSTONE=y
-CONFIG_POWER_RESET_RMOBILE=y
-CONFIG_POWER_RESET_ST=y
-CONFIG_POWER_AVS=y
-CONFIG_ROCKCHIP_IODOMAIN=y
 CONFIG_SENSORS_IIO_HWMON=y
 CONFIG_SENSORS_LM90=y
 CONFIG_SENSORS_LM95245=y
@@ -480,14 +449,12 @@ CONFIG_SENSORS_NTC_THERMISTOR=m
 CONFIG_SENSORS_PWM_FAN=m
 CONFIG_SENSORS_INA2XX=m
 CONFIG_CPU_THERMAL=y
-CONFIG_BCM2835_THERMAL=m
-CONFIG_BRCMSTB_THERMAL=m
 CONFIG_IMX_THERMAL=y
 CONFIG_ROCKCHIP_THERMAL=y
 CONFIG_RCAR_THERMAL=y
 CONFIG_ARMADA_THERMAL=y
-CONFIG_DAVINCI_WATCHDOG=m
-CONFIG_EXYNOS_THERMAL=m
+CONFIG_BCM2835_THERMAL=m
+CONFIG_BRCMSTB_THERMAL=m
 CONFIG_ST_THERMAL_MEMMAP=y
 CONFIG_WATCHDOG=y
 CONFIG_DA9063_WATCHDOG=m
@@ -495,20 +462,24 @@ CONFIG_XILINX_WATCHDOG=y
 CONFIG_ARM_SP805_WATCHDOG=y
 CONFIG_AT91SAM9X_WATCHDOG=y
 CONFIG_SAMA5D4_WATCHDOG=y
+CONFIG_DW_WATCHDOG=y
+CONFIG_DAVINCI_WATCHDOG=m
 CONFIG_ORION_WATCHDOG=y
 CONFIG_RN5T618_WATCHDOG=y
-CONFIG_ST_LPC_WATCHDOG=y
 CONFIG_SUNXI_WATCHDOG=y
 CONFIG_IMX2_WDT=y
+CONFIG_ST_LPC_WATCHDOG=y
 CONFIG_TEGRA_WATCHDOG=m
 CONFIG_MESON_WATCHDOG=y
-CONFIG_DW_WATCHDOG=y
 CONFIG_DIGICOLOR_WATCHDOG=y
 CONFIG_RENESAS_WDT=m
-CONFIG_BCM2835_WDT=y
 CONFIG_BCM47XX_WDT=y
-CONFIG_BCM7038_WDT=m
+CONFIG_BCM2835_WDT=y
 CONFIG_BCM_KONA_WDT=y
+CONFIG_BCM7038_WDT=m
+CONFIG_BCMA_HOST_SOC=y
+CONFIG_BCMA_DRIVER_GMAC_CMN=y
+CONFIG_BCMA_DRIVER_GPIO=y
 CONFIG_MFD_ACT8945A=y
 CONFIG_MFD_AS3711=y
 CONFIG_MFD_AS3722=y
@@ -516,7 +487,6 @@ CONFIG_MFD_ATMEL_FLEXCOM=y
 CONFIG_MFD_ATMEL_HLCDC=m
 CONFIG_MFD_BCM590XX=y
 CONFIG_MFD_AC100=y
-CONFIG_MFD_AXP20X=y
 CONFIG_MFD_AXP20X_I2C=y
 CONFIG_MFD_AXP20X_RSB=y
 CONFIG_MFD_CROS_EC=m
@@ -529,11 +499,11 @@ CONFIG_MFD_MAX77693=m
 CONFIG_MFD_MAX8907=y
 CONFIG_MFD_MAX8997=y
 CONFIG_MFD_MAX8998=y
-CONFIG_MFD_RK808=y
 CONFIG_MFD_CPCAP=y
 CONFIG_MFD_PM8XXX=y
 CONFIG_MFD_QCOM_RPM=y
 CONFIG_MFD_SPMI_PMIC=y
+CONFIG_MFD_RK808=y
 CONFIG_MFD_RN5T618=y
 CONFIG_MFD_SEC_CORE=y
 CONFIG_MFD_STMPE=y
@@ -543,10 +513,10 @@ CONFIG_MFD_TPS65217=y
 CONFIG_MFD_TPS65218=y
 CONFIG_MFD_TPS6586X=y
 CONFIG_MFD_TPS65910=y
-CONFIG_REGULATOR_ACT8945A=y
-CONFIG_REGULATOR_AB8500=y
 CONFIG_REGULATOR_ACT8865=y
+CONFIG_REGULATOR_ACT8945A=y
 CONFIG_REGULATOR_ANATOP=y
+CONFIG_REGULATOR_AB8500=y
 CONFIG_REGULATOR_AS3711=y
 CONFIG_REGULATOR_AS3722=y
 CONFIG_REGULATOR_AXP20X=y
@@ -554,10 +524,7 @@ CONFIG_REGULATOR_BCM590XX=y
 CONFIG_REGULATOR_CPCAP=y
 CONFIG_REGULATOR_DA9210=y
 CONFIG_REGULATOR_FAN53555=y
-CONFIG_REGULATOR_RK808=y
 CONFIG_REGULATOR_GPIO=y
-CONFIG_MFD_SYSCON=y
-CONFIG_POWER_RESET_SYSCON=y
 CONFIG_REGULATOR_LP872X=y
 CONFIG_REGULATOR_MAX14577=m
 CONFIG_REGULATOR_MAX8907=y
@@ -571,7 +538,8 @@ CONFIG_REGULATOR_PALMAS=y
 CONFIG_REGULATOR_PBIAS=y
 CONFIG_REGULATOR_PWM=y
 CONFIG_REGULATOR_QCOM_RPM=y
-CONFIG_REGULATOR_QCOM_SMD_RPM=y
+CONFIG_REGULATOR_QCOM_SMD_RPM=m
+CONFIG_REGULATOR_RK808=y
 CONFIG_REGULATOR_RN5T618=y
 CONFIG_REGULATOR_S2MPS11=y
 CONFIG_REGULATOR_S5M8767=y
@@ -592,18 +560,17 @@ CONFIG_MEDIA_CEC_SUPPORT=y
 CONFIG_MEDIA_CONTROLLER=y
 CONFIG_VIDEO_V4L2_SUBDEV_API=y
 CONFIG_MEDIA_USB_SUPPORT=y
-CONFIG_USB_VIDEO_CLASS=y
-CONFIG_USB_GSPCA=y
+CONFIG_USB_VIDEO_CLASS=m
 CONFIG_V4L_PLATFORM_DRIVERS=y
 CONFIG_SOC_CAMERA=m
 CONFIG_SOC_CAMERA_PLATFORM=m
-CONFIG_VIDEO_RCAR_VIN=m
-CONFIG_VIDEO_ATMEL_ISI=m
 CONFIG_VIDEO_SAMSUNG_EXYNOS4_IS=m
 CONFIG_VIDEO_S5P_FIMC=m
 CONFIG_VIDEO_S5P_MIPI_CSIS=m
 CONFIG_VIDEO_EXYNOS_FIMC_LITE=m
 CONFIG_VIDEO_EXYNOS4_FIMC_IS=m
+CONFIG_VIDEO_RCAR_VIN=m
+CONFIG_VIDEO_ATMEL_ISI=m
 CONFIG_V4L_MEM2MEM_DRIVERS=y
 CONFIG_VIDEO_SAMSUNG_S5P_JPEG=m
 CONFIG_VIDEO_SAMSUNG_S5P_MFC=m
@@ -614,19 +581,15 @@ CONFIG_VIDEO_STI_DELTA=m
 CONFIG_VIDEO_RENESAS_JPU=m
 CONFIG_VIDEO_RENESAS_VSP1=m
 CONFIG_V4L_TEST_DRIVERS=y
+CONFIG_VIDEO_VIVID=m
 CONFIG_CEC_PLATFORM_DRIVERS=y
 CONFIG_VIDEO_SAMSUNG_S5P_CEC=m
 # CONFIG_MEDIA_SUBDRV_AUTOSELECT is not set
 CONFIG_VIDEO_ADV7180=m
 CONFIG_VIDEO_ML86V7667=m
 CONFIG_DRM=y
-CONFIG_DRM_I2C_ADV7511=m
-CONFIG_DRM_I2C_ADV7511_AUDIO=y
 # CONFIG_DRM_I2C_CH7006 is not set
 # CONFIG_DRM_I2C_SIL164 is not set
-CONFIG_DRM_DUMB_VGA_DAC=m
-CONFIG_DRM_NXP_PTN3460=m
-CONFIG_DRM_PARADE_PS8622=m
 CONFIG_DRM_NOUVEAU=m
 CONFIG_DRM_EXYNOS=m
 CONFIG_DRM_EXYNOS_FIMD=y
@@ -645,13 +608,18 @@ CONFIG_DRM_RCAR_LVDS=y
 CONFIG_DRM_SUN4I=m
 CONFIG_DRM_FSL_DCU=m
 CONFIG_DRM_TEGRA=y
+CONFIG_DRM_PANEL_SIMPLE=y
 CONFIG_DRM_PANEL_SAMSUNG_LD9040=m
 CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03=m
 CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0=m
-CONFIG_DRM_PANEL_SIMPLE=y
+CONFIG_DRM_DUMB_VGA_DAC=m
+CONFIG_DRM_NXP_PTN3460=m
+CONFIG_DRM_PARADE_PS8622=m
 CONFIG_DRM_SII9234=m
+CONFIG_DRM_I2C_ADV7511=m
+CONFIG_DRM_I2C_ADV7511_AUDIO=y
 CONFIG_DRM_STI=m
-CONFIG_DRM_VC4=y
+CONFIG_DRM_VC4=m
 CONFIG_DRM_ETNAVIV=m
 CONFIG_DRM_MXSFB=m
 CONFIG_FB_ARMCLCD=y
@@ -659,8 +627,6 @@ CONFIG_FB_EFI=y
 CONFIG_FB_WM8505=y
 CONFIG_FB_SH_MOBILE_LCDC=y
 CONFIG_FB_SIMPLE=y
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
 CONFIG_LCD_PLATFORM=m
 CONFIG_BACKLIGHT_PWM=y
 CONFIG_BACKLIGHT_AS3711=y
@@ -668,7 +634,6 @@ CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
 CONFIG_SOUND=m
 CONFIG_SND=m
-CONFIG_SND_DYNAMIC_MINORS=y
 CONFIG_SND_HDA_TEGRA=m
 CONFIG_SND_HDA_INPUT_BEEP=y
 CONFIG_SND_HDA_PATCH_LOADER=y
@@ -692,7 +657,7 @@ CONFIG_SND_SOC_SNOW=m
 CONFIG_SND_SOC_ODROID=m
 CONFIG_SND_SOC_SH4_FSI=m
 CONFIG_SND_SOC_RCAR=m
-CONFIG_SND_SIMPLE_SCU_CARD=m
+CONFIG_SND_SOC_STI=m
 CONFIG_SND_SUN4I_CODEC=m
 CONFIG_SND_SOC_TEGRA=m
 CONFIG_SND_SOC_TEGRA20_I2S=m
@@ -703,31 +668,25 @@ CONFIG_SND_SOC_TEGRA_WM8903=m
 CONFIG_SND_SOC_TEGRA_WM9712=m
 CONFIG_SND_SOC_TEGRA_TRIMSLICE=m
 CONFIG_SND_SOC_TEGRA_ALC5632=m
-CONFIG_SND_SOC_CPCAP=m
 CONFIG_SND_SOC_TEGRA_MAX98090=m
 CONFIG_SND_SOC_AK4642=m
+CONFIG_SND_SOC_CPCAP=m
 CONFIG_SND_SOC_SGTL5000=m
 CONFIG_SND_SOC_SPDIF=m
-CONFIG_SND_SOC_WM8978=m
-CONFIG_SND_SOC_STI=m
 CONFIG_SND_SOC_STI_SAS=m
-CONFIG_SND_SIMPLE_CARD=m
+CONFIG_SND_SOC_WM8978=m
+CONFIG_SND_SIMPLE_SCU_CARD=m
 CONFIG_USB=y
 CONFIG_USB_OTG=y
 CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_MVEBU=y
-CONFIG_USB_XHCI_RCAR=m
 CONFIG_USB_XHCI_TEGRA=m
 CONFIG_USB_EHCI_HCD=y
-CONFIG_USB_EHCI_MSM=m
-CONFIG_USB_EHCI_EXYNOS=y
-CONFIG_USB_EHCI_TEGRA=y
 CONFIG_USB_EHCI_HCD_STI=y
-CONFIG_USB_EHCI_HCD_PLATFORM=y
-CONFIG_USB_ISP1760=y
+CONFIG_USB_EHCI_TEGRA=y
+CONFIG_USB_EHCI_EXYNOS=y
 CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_OHCI_HCD_STI=y
-CONFIG_USB_OHCI_HCD_PLATFORM=y
 CONFIG_USB_OHCI_EXYNOS=m
 CONFIG_USB_R8A66597_HCD=m
 CONFIG_USB_RENESAS_USBHS=m
@@ -746,18 +705,18 @@ CONFIG_USB_TI_CPPI41_DMA=y
 CONFIG_USB_TUSB_OMAP_DMA=y
 CONFIG_USB_DWC3=y
 CONFIG_USB_DWC2=y
-CONFIG_USB_HSIC_USB3503=y
 CONFIG_USB_CHIPIDEA=y
 CONFIG_USB_CHIPIDEA_UDC=y
 CONFIG_USB_CHIPIDEA_HOST=y
+CONFIG_USB_ISP1760=y
+CONFIG_USB_HSIC_USB3503=y
 CONFIG_AB8500_USB=y
-CONFIG_KEYSTONE_USB_PHY=y
+CONFIG_KEYSTONE_USB_PHY=m
 CONFIG_NOP_USB_XCEIV=m
 CONFIG_AM335X_PHY_USB=m
 CONFIG_TWL6030_USB=m
 CONFIG_USB_GPIO_VBUS=y
 CONFIG_USB_ISP1301=y
-CONFIG_USB_MSM_OTG=m
 CONFIG_USB_MXS_PHY=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_FSL_USB2=y
@@ -793,21 +752,20 @@ CONFIG_MMC_SDHCI_OF_ESDHC=y
 CONFIG_MMC_SDHCI_ESDHC_IMX=y
 CONFIG_MMC_SDHCI_DOVE=y
 CONFIG_MMC_SDHCI_TEGRA=y
+CONFIG_MMC_SDHCI_S3C=y
 CONFIG_MMC_SDHCI_PXAV3=y
 CONFIG_MMC_SDHCI_SPEAR=y
-CONFIG_MMC_SDHCI_S3C=y
 CONFIG_MMC_SDHCI_S3C_DMA=y
 CONFIG_MMC_SDHCI_BCM_KONA=y
+CONFIG_MMC_MESON_MX_SDIO=y
 CONFIG_MMC_SDHCI_ST=y
 CONFIG_MMC_OMAP=y
 CONFIG_MMC_OMAP_HS=y
 CONFIG_MMC_ATMELMCI=y
 CONFIG_MMC_SDHCI_MSM=y
-CONFIG_MMC_MESON_MX_SDIO=y
 CONFIG_MMC_MVSDIO=y
 CONFIG_MMC_SDHI=y
 CONFIG_MMC_DW=y
-CONFIG_MMC_DW_PLTFM=y
 CONFIG_MMC_DW_EXYNOS=y
 CONFIG_MMC_DW_ROCKCHIP=y
 CONFIG_MMC_SH_MMCIF=y
@@ -847,94 +805,85 @@ CONFIG_RTC_DRV_MAX77686=y
 CONFIG_RTC_DRV_RK808=m
 CONFIG_RTC_DRV_RS5C372=m
 CONFIG_RTC_DRV_BQ32K=m
-CONFIG_RTC_DRV_PALMAS=y
-CONFIG_RTC_DRV_ST_LPC=y
 CONFIG_RTC_DRV_TWL4030=y
+CONFIG_RTC_DRV_PALMAS=y
 CONFIG_RTC_DRV_TPS6586X=y
 CONFIG_RTC_DRV_TPS65910=y
 CONFIG_RTC_DRV_S35390A=m
 CONFIG_RTC_DRV_RX8581=m
 CONFIG_RTC_DRV_EM3027=y
+CONFIG_RTC_DRV_S5M=m
 CONFIG_RTC_DRV_DA9063=m
 CONFIG_RTC_DRV_EFI=m
 CONFIG_RTC_DRV_DIGICOLOR=m
-CONFIG_RTC_DRV_S5M=m
 CONFIG_RTC_DRV_S3C=m
 CONFIG_RTC_DRV_PL031=y
 CONFIG_RTC_DRV_AT91RM9200=m
 CONFIG_RTC_DRV_AT91SAM9=m
 CONFIG_RTC_DRV_VT8500=y
-CONFIG_RTC_DRV_SUN6I=y
 CONFIG_RTC_DRV_SUNXI=y
 CONFIG_RTC_DRV_MV=y
 CONFIG_RTC_DRV_TEGRA=y
+CONFIG_RTC_DRV_ST_LPC=y
 CONFIG_RTC_DRV_CPCAP=m
 CONFIG_DMADEVICES=y
-CONFIG_DW_DMAC=y
 CONFIG_AT_HDMAC=y
 CONFIG_AT_XDMAC=y
+CONFIG_DMA_BCM2835=y
+CONFIG_DMA_SUN6I=y
 CONFIG_FSL_EDMA=y
+CONFIG_IMX_DMA=y
+CONFIG_IMX_SDMA=y
 CONFIG_MV_XOR=y
+CONFIG_MXS_DMA=y
+CONFIG_PL330_DMA=y
+CONFIG_SIRF_DMA=y
+CONFIG_STE_DMA40=y
+CONFIG_ST_FDMA=m
 CONFIG_TEGRA20_APB_DMA=y
+CONFIG_XILINX_DMA=y
+CONFIG_QCOM_BAM_DMA=y
+CONFIG_DW_DMAC=y
 CONFIG_SH_DMAE=y
 CONFIG_RCAR_DMAC=y
 CONFIG_RENESAS_USB_DMAC=m
-CONFIG_STE_DMA40=y
-CONFIG_SIRF_DMA=y
-CONFIG_TI_EDMA=y
-CONFIG_PL330_DMA=y
-CONFIG_IMX_SDMA=y
-CONFIG_IMX_DMA=y
-CONFIG_MXS_DMA=y
-CONFIG_DMA_BCM2835=y
-CONFIG_DMA_OMAP=y
-CONFIG_QCOM_BAM_DMA=y
-CONFIG_XILINX_DMA=y
-CONFIG_DMA_SUN6I=y
-CONFIG_ST_FDMA=m
+CONFIG_VIRTIO_PCI=y
+CONFIG_VIRTIO_MMIO=y
 CONFIG_STAGING=y
-CONFIG_SENSORS_ISL29018=y
-CONFIG_SENSORS_ISL29028=y
 CONFIG_MFD_NVEC=y
 CONFIG_KEYBOARD_NVEC=y
 CONFIG_SERIO_NVEC_PS2=y
 CONFIG_NVEC_POWER=y
 CONFIG_NVEC_PAZ00=y
-CONFIG_BCMA=y
-CONFIG_BCMA_HOST_SOC=y
-CONFIG_BCMA_DRIVER_GMAC_CMN=y
-CONFIG_BCMA_DRIVER_GPIO=y
-CONFIG_QCOM_GSBI=y
-CONFIG_QCOM_PM=y
-CONFIG_QCOM_SMEM=y
-CONFIG_QCOM_SMD_RPM=y
-CONFIG_QCOM_SMP2P=y
-CONFIG_QCOM_SMSM=y
-CONFIG_QCOM_WCNSS_CTRL=m
-CONFIG_ROCKCHIP_PM_DOMAINS=y
-CONFIG_COMMON_CLK_QCOM=y
-CONFIG_QCOM_CLK_RPM=y
-CONFIG_CHROME_PLATFORMS=y
 CONFIG_STAGING_BOARD=y
-CONFIG_CROS_EC_CHARDEV=m
 CONFIG_COMMON_CLK_MAX77686=y
 CONFIG_COMMON_CLK_RK808=m
 CONFIG_COMMON_CLK_S2MPS11=m
+CONFIG_COMMON_CLK_QCOM=y
+CONFIG_QCOM_CLK_RPM=y
 CONFIG_APQ_MMCC_8084=y
 CONFIG_MSM_GCC_8660=y
 CONFIG_MSM_MMCC_8960=y
 CONFIG_MSM_MMCC_8974=y
-CONFIG_HWSPINLOCK_QCOM=y
+CONFIG_BCM2835_MBOX=y
 CONFIG_ROCKCHIP_IOMMU=y
 CONFIG_TEGRA_IOMMU_GART=y
 CONFIG_TEGRA_IOMMU_SMMU=y
 CONFIG_REMOTEPROC=m
 CONFIG_ST_REMOTEPROC=m
 CONFIG_RPMSG_VIRTIO=m
+CONFIG_RASPBERRYPI_POWER=y
+CONFIG_QCOM_GSBI=y
+CONFIG_QCOM_PM=y
+CONFIG_QCOM_SMD_RPM=m
+CONFIG_QCOM_WCNSS_CTRL=m
+CONFIG_ROCKCHIP_PM_DOMAINS=y
+CONFIG_ARCH_TEGRA_2x_SOC=y
+CONFIG_ARCH_TEGRA_3x_SOC=y
+CONFIG_ARCH_TEGRA_114_SOC=y
+CONFIG_ARCH_TEGRA_124_SOC=y
 CONFIG_PM_DEVFREQ=y
 CONFIG_ARM_TEGRA_DEVFREQ=m
-CONFIG_MEMORY=y
-CONFIG_EXTCON=y
 CONFIG_TI_AEMIF=y
 CONFIG_IIO=y
 CONFIG_IIO_SW_TRIGGER=y
@@ -947,56 +896,54 @@ CONFIG_VF610_ADC=m
 CONFIG_XILINX_XADC=y
 CONFIG_MPU3050_I2C=y
 CONFIG_CM36651=m
+CONFIG_SENSORS_ISL29018=y
+CONFIG_SENSORS_ISL29028=y
 CONFIG_AK8975=y
-CONFIG_RASPBERRYPI_POWER=y
 CONFIG_IIO_HRTIMER_TRIGGER=y
 CONFIG_PWM=y
 CONFIG_PWM_ATMEL=m
 CONFIG_PWM_ATMEL_HLCDC_PWM=m
 CONFIG_PWM_ATMEL_TCB=m
+CONFIG_PWM_BCM2835=y
+CONFIG_PWM_BRCMSTB=m
 CONFIG_PWM_FSL_FTM=m
 CONFIG_PWM_MESON=m
 CONFIG_PWM_RCAR=m
 CONFIG_PWM_RENESAS_TPU=y
 CONFIG_PWM_ROCKCHIP=m
 CONFIG_PWM_SAMSUNG=m
+CONFIG_PWM_STI=y
 CONFIG_PWM_SUN4I=y
 CONFIG_PWM_TEGRA=y
 CONFIG_PWM_VT8500=y
+CONFIG_KEYSTONE_IRQ=y
+CONFIG_PHY_SUN4I_USB=y
+CONFIG_PHY_SUN9I_USB=y
 CONFIG_PHY_HIX5HD2_SATA=y
-CONFIG_E1000E=y
-CONFIG_PWM_STI=y
-CONFIG_PWM_BCM2835=y
-CONFIG_PWM_BRCMSTB=m
-CONFIG_PHY_DM816X_USB=m
-CONFIG_OMAP_USB2=y
-CONFIG_TI_PIPE3=y
-CONFIG_TWL4030_USB=m
+CONFIG_PHY_BERLIN_SATA=y
 CONFIG_PHY_BERLIN_USB=y
 CONFIG_PHY_CPCAP_USB=m
-CONFIG_PHY_BERLIN_SATA=y
+CONFIG_PHY_QCOM_APQ8064_SATA=m
+CONFIG_PHY_RCAR_GEN2=m
 CONFIG_PHY_ROCKCHIP_DP=m
 CONFIG_PHY_ROCKCHIP_USB=y
-CONFIG_PHY_QCOM_APQ8064_SATA=m
+CONFIG_PHY_SAMSUNG_USB2=m
 CONFIG_PHY_MIPHY28LP=y
-CONFIG_PHY_RCAR_GEN2=m
 CONFIG_PHY_STIH407_USB=y
 CONFIG_PHY_STM32_USBPHYC=y
-CONFIG_PHY_SUN4I_USB=y
-CONFIG_PHY_SUN9I_USB=y
-CONFIG_PHY_SAMSUNG_USB2=m
 CONFIG_PHY_TEGRA_XUSB=y
-CONFIG_PHY_BRCM_SATA=y
-CONFIG_NVMEM=y
+CONFIG_PHY_DM816X_USB=m
+CONFIG_OMAP_USB2=y
+CONFIG_TI_PIPE3=y
+CONFIG_TWL4030_USB=m
 CONFIG_NVMEM_IMX_OCOTP=y
 CONFIG_NVMEM_SUNXI_SID=y
 CONFIG_NVMEM_VF610_OCOTP=y
-CONFIG_BCM2835_MBOX=y
 CONFIG_RASPBERRYPI_FIRMWARE=y
-CONFIG_EFI_VARS=m
-CONFIG_EFI_CAPSULE_LOADER=m
 CONFIG_BCM47XX_NVRAM=y
 CONFIG_BCM47XX_SPROM=y
+CONFIG_EFI_VARS=m
+CONFIG_EFI_CAPSULE_LOADER=m
 CONFIG_EXT4_FS=y
 CONFIG_AUTOFS4_FS=y
 CONFIG_MSDOS_FS=y
@@ -1004,7 +951,6 @@ CONFIG_VFAT_FS=y
 CONFIG_NTFS_FS=y
 CONFIG_TMPFS_POSIX_ACL=y
 CONFIG_UBIFS_FS=y
-CONFIG_TMPFS=y
 CONFIG_SQUASHFS=y
 CONFIG_SQUASHFS_LZO=y
 CONFIG_SQUASHFS_XZ=y
@@ -1020,13 +966,7 @@ CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_UTF8=y
 CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_FS=y
 CONFIG_MAGIC_SYSRQ=y
-CONFIG_LOCKUP_DETECTOR=y
-CONFIG_CPUFREQ_DT=y
-CONFIG_KEYSTONE_IRQ=y
-CONFIG_HW_RANDOM=y
-CONFIG_HW_RANDOM_ST=y
 CONFIG_CRYPTO_USER=m
 CONFIG_CRYPTO_USER_API_HASH=m
 CONFIG_CRYPTO_USER_API_SKCIPHER=m
@@ -1035,27 +975,19 @@ CONFIG_CRYPTO_USER_API_AEAD=m
 CONFIG_CRYPTO_DEV_MARVELL_CESA=m
 CONFIG_CRYPTO_DEV_EXYNOS_RNG=m
 CONFIG_CRYPTO_DEV_S5P=m
+CONFIG_CRYPTO_DEV_ATMEL_AES=m
+CONFIG_CRYPTO_DEV_ATMEL_TDES=m
+CONFIG_CRYPTO_DEV_ATMEL_SHA=m
 CONFIG_CRYPTO_DEV_SUN4I_SS=m
 CONFIG_CRYPTO_DEV_ROCKCHIP=m
 CONFIG_ARM_CRYPTO=y
-CONFIG_CRYPTO_SHA1_ARM=m
 CONFIG_CRYPTO_SHA1_ARM_NEON=m
 CONFIG_CRYPTO_SHA1_ARM_CE=m
 CONFIG_CRYPTO_SHA2_ARM_CE=m
-CONFIG_CRYPTO_SHA256_ARM=m
 CONFIG_CRYPTO_SHA512_ARM=m
 CONFIG_CRYPTO_AES_ARM=m
 CONFIG_CRYPTO_AES_ARM_BS=m
 CONFIG_CRYPTO_AES_ARM_CE=m
-CONFIG_CRYPTO_CHACHA20_NEON=m
-CONFIG_CRYPTO_CRC32_ARM_CE=m
-CONFIG_CRYPTO_CRCT10DIF_ARM_CE=m
 CONFIG_CRYPTO_GHASH_ARM_CE=m
-CONFIG_CRYPTO_DEV_ATMEL_AES=m
-CONFIG_CRYPTO_DEV_ATMEL_TDES=m
-CONFIG_CRYPTO_DEV_ATMEL_SHA=m
-CONFIG_VIDEO_VIVID=m
-CONFIG_VIRTIO=y
-CONFIG_VIRTIO_PCI=y
-CONFIG_VIRTIO_PCI_LEGACY=y
-CONFIG_VIRTIO_MMIO=y
+CONFIG_CRYPTO_CRC32_ARM_CE=m
+CONFIG_CRYPTO_CHACHA20_NEON=m

arch/arm/crypto/speck-neon-core.S

@@ -272,9 +272,11 @@
 	 * Allocate stack space to store 128 bytes worth of tweaks.  For
 	 * performance, this space is aligned to a 16-byte boundary so that we
 	 * can use the load/store instructions that declare 16-byte alignment.
+	 * For Thumb2 compatibility, don't do the 'bic' directly on 'sp'.
 	 */
-	sub		sp, #128
-	bic		sp, #0xf
+	sub		r12, sp, #128
+	bic		r12, #0xf
+	mov		sp, r12
 
 .if \n == 64
 	// Load first tweak

arch/arm/firmware/Makefile

@@ -1 +1,4 @@
 obj-$(CONFIG_TRUSTED_FOUNDATIONS)	+= trusted_foundations.o
+
+# tf_generic_smc() fails to build with -fsanitize-coverage=trace-pc
+KCOV_INSTRUMENT                := n

arch/arm/kernel/head-nommu.S

@@ -177,7 +177,7 @@ M_CLASS(streq	r3, [r12, #PMSAv8_MAIR1])
 	bic	r0, r0, #CR_I
 #endif
 	mcr	p15, 0, r0, c1, c0, 0		@ write control reg
-	isb
+	instr_sync
 #elif defined (CONFIG_CPU_V7M)
 #ifdef CONFIG_ARM_MPU
 	ldreq	r3, [r12, MPU_CTRL]

arch/arm/mach-bcm/Kconfig

@@ -20,6 +20,7 @@ config ARCH_BCM_IPROC
 	select GPIOLIB
 	select ARM_AMBA
 	select PINCTRL
+	select PCI_DOMAINS if PCI
 	help
 	  This enables support for systems based on Broadcom IPROC architected SoCs.
 	  The IPROC complex contains one or more ARM CPUs along with common

arch/arm/mach-davinci/board-da850-evm.c

@@ -774,7 +774,7 @@ static struct gpiod_lookup_table mmc_gpios_table = {
 		GPIO_LOOKUP("davinci_gpio.0", DA850_MMCSD_CD_PIN, "cd",
 			    GPIO_ACTIVE_LOW),
 		GPIO_LOOKUP("davinci_gpio.0", DA850_MMCSD_WP_PIN, "wp",
-			    GPIO_ACTIVE_LOW),
+			    GPIO_ACTIVE_HIGH),
 	},
 };
 

arch/arm/mach-omap2/omap-smp.c

@@ -109,6 +109,45 @@ void omap5_erratum_workaround_801819(void)
 static inline void omap5_erratum_workaround_801819(void) { }
 #endif
 
+#ifdef CONFIG_HARDEN_BRANCH_PREDICTOR
+/*
+ * Configure ACR and enable ACTLR[0] (Enable invalidates of BTB with
+ * ICIALLU) to activate the workaround for secondary Core.
+ * NOTE: it is assumed that the primary core's configuration is done
+ * by the boot loader (kernel will detect a misconfiguration and complain
+ * if this is not done).
+ *
+ * In General Purpose(GP) devices, ACR bit settings can only be done
+ * by ROM code in "secure world" using the smc call and there is no
+ * option to update the "firmware" on such devices. This also works for
+ * High security(HS) devices, as a backup option in case the
+ * "update" is not done in the "security firmware".
+ */
+static void omap5_secondary_harden_predictor(void)
+{
+	u32 acr, acr_mask;
+
+	asm volatile ("mrc p15, 0, %0, c1, c0, 1" : "=r" (acr));
+
+	/*
+	 * ACTLR[0] (Enable invalidates of BTB with ICIALLU)
+	 */
+	acr_mask = BIT(0);
+
+	/* Do we already have it done.. if yes, skip expensive smc */
+	if ((acr & acr_mask) == acr_mask)
+		return;
+
+	acr |= acr_mask;
+	omap_smc1(OMAP5_DRA7_MON_SET_ACR_INDEX, acr);
+
+	pr_debug("%s: ARM ACR setup for CVE_2017_5715 applied on CPU%d\n",
+		 __func__, smp_processor_id());
+}
+#else
+static inline void omap5_secondary_harden_predictor(void) { }
+#endif
+
 static void omap4_secondary_init(unsigned int cpu)
 {
 	/*
@@ -131,6 +170,8 @@ static void omap4_secondary_init(unsigned int cpu)
 		set_cntfreq();
 		/* Configure ACR to disable streaming WA for 801819 */
 		omap5_erratum_workaround_801819();
+		/* Enable ACR to allow for ICUALLU workaround */
+		omap5_secondary_harden_predictor();
 	}
 
 	/*

arch/arm/mach-pxa/irq.c

@@ -185,7 +185,7 @@ static int pxa_irq_suspend(void)
 {
 	int i;
 
-	for (i = 0; i < pxa_internal_irq_nr / 32; i++) {
+	for (i = 0; i < DIV_ROUND_UP(pxa_internal_irq_nr, 32); i++) {
 		void __iomem *base = irq_base(i);
 
 		saved_icmr[i] = __raw_readl(base + ICMR);
@@ -204,7 +204,7 @@ static void pxa_irq_resume(void)
 {
 	int i;
 
-	for (i = 0; i < pxa_internal_irq_nr / 32; i++) {
+	for (i = 0; i < DIV_ROUND_UP(pxa_internal_irq_nr, 32); i++) {
 		void __iomem *base = irq_base(i);
 
 		__raw_writel(saved_icmr[i], base + ICMR);

arch/arm/mach-socfpga/Kconfig

@@ -10,6 +10,7 @@ menuconfig ARCH_SOCFPGA
 	select HAVE_ARM_SCU
 	select HAVE_ARM_TWD if SMP
 	select MFD_SYSCON
+	select PCI_DOMAINS if PCI
 
 if ARCH_SOCFPGA
 config SOCFPGA_SUSPEND

arch/arm/mm/init.c

@@ -736,20 +736,29 @@ static int __mark_rodata_ro(void *unused)
 	return 0;
 }
 
+static int kernel_set_to_readonly __read_mostly;
+
 void mark_rodata_ro(void)
 {
+	kernel_set_to_readonly = 1;
 	stop_machine(__mark_rodata_ro, NULL, NULL);
 	debug_checkwx();
 }
 
 void set_kernel_text_rw(void)
 {
+	if (!kernel_set_to_readonly)
+		return;
+
 	set_section_perms(ro_perms, ARRAY_SIZE(ro_perms), false,
 				current->active_mm);
 }
 
 void set_kernel_text_ro(void)
 {
+	if (!kernel_set_to_readonly)
+		return;
+
 	set_section_perms(ro_perms, ARRAY_SIZE(ro_perms), true,
 				current->active_mm);
 }

arch/arm/net/bpf_jit_32.c

@@ -1844,7 +1844,7 @@ struct bpf_prog *bpf_int_jit_compile(struct bpf_prog *prog)
 		/* there are 2 passes here */
 		bpf_jit_dump(prog->len, image_size, 2, ctx.target);
 
-	set_memory_ro((unsigned long)header, header->pages);
+	bpf_jit_binary_lock_ro(header);
 	prog->bpf_func = (void *)ctx.target;
 	prog->jited = 1;
 	prog->jited_len = image_size;

arch/arm64/Makefile

@@ -10,7 +10,7 @@
 #
 # Copyright (C) 1995-2001 by Russell King
 
-LDFLAGS_vmlinux	:=-p --no-undefined -X
+LDFLAGS_vmlinux	:=--no-undefined -X
 CPPFLAGS_vmlinux.lds = -DTEXT_OFFSET=$(TEXT_OFFSET)
 GZFLAGS		:=-9
 
@@ -60,15 +60,15 @@ ifeq ($(CONFIG_CPU_BIG_ENDIAN), y)
 KBUILD_CPPFLAGS	+= -mbig-endian
 CHECKFLAGS	+= -D__AARCH64EB__
 AS		+= -EB
-LD		+= -EB
-LDFLAGS		+= -maarch64linuxb
+# We must use the linux target here, since distributions don't tend to package
+# the ELF linker scripts with binutils, and this results in a build failure.
+LDFLAGS		+= -EB -maarch64linuxb
 UTS_MACHINE	:= aarch64_be
 else
 KBUILD_CPPFLAGS	+= -mlittle-endian
 CHECKFLAGS	+= -D__AARCH64EL__
 AS		+= -EL
-LD		+= -EL
-LDFLAGS		+= -maarch64linux
+LDFLAGS		+= -EL -maarch64linux # See comment above
 UTS_MACHINE	:= aarch64
 endif
 

arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi

@@ -309,8 +309,7 @@
 			interrupts = <0 99 4>;
 			resets = <&rst SPIM0_RESET>;
 			reg-io-width = <4>;
-			num-chipselect = <4>;
-			bus-num = <0>;
+			num-cs = <4>;
 			status = "disabled";
 		};
 
@@ -322,8 +321,7 @@
 			interrupts = <0 100 4>;
 			resets = <&rst SPIM1_RESET>;
 			reg-io-width = <4>;
-			num-chipselect = <4>;
-			bus-num = <0>;
+			num-cs = <4>;
 			status = "disabled";
 		};
 

arch/arm64/boot/dts/amlogic/meson-axg-s400.dts

@@ -66,9 +66,22 @@
 
 &ethmac {
 	status = "okay";
-	phy-mode = "rgmii";
 	pinctrl-0 = <&eth_rgmii_y_pins>;
 	pinctrl-names = "default";
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rgmii";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth_phy0: ethernet-phy@0 {
+			/* Realtek RTL8211F (0x001cc916) */
+			reg = <0>;
+			eee-broken-1000t;
+		};
+	};
 };
 
 &uart_A {

arch/arm64/boot/dts/amlogic/meson-axg.dtsi

@@ -132,7 +132,7 @@
 
 			sd_emmc_b: sd@5000 {
 				compatible = "amlogic,meson-axg-mmc";
-				reg = <0x0 0x5000 0x0 0x2000>;
+				reg = <0x0 0x5000 0x0 0x800>;
 				interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 				clocks = <&clkc CLKID_SD_EMMC_B>,
@@ -144,7 +144,7 @@
 
 			sd_emmc_c: mmc@7000 {
 				compatible = "amlogic,meson-axg-mmc";
-				reg = <0x0 0x7000 0x0 0x2000>;
+				reg = <0x0 0x7000 0x0 0x800>;
 				interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 				clocks = <&clkc CLKID_SD_EMMC_C>,

arch/arm64/boot/dts/amlogic/meson-gx.dtsi

@@ -35,6 +35,12 @@
 			no-map;
 		};
 
+		/* Alternate 3 MiB reserved for ARM Trusted Firmware (BL31) */
+		secmon_reserved_alt: secmon@5000000 {
+			reg = <0x0 0x05000000 0x0 0x300000>;
+			no-map;
+		};
+
 		linux,cma {
 			compatible = "shared-dma-pool";
 			reusable;
@@ -457,21 +463,21 @@
 
 			sd_emmc_a: mmc@70000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
-				reg = <0x0 0x70000 0x0 0x2000>;
+				reg = <0x0 0x70000 0x0 0x800>;
 				interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};
 
 			sd_emmc_b: mmc@72000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
-				reg = <0x0 0x72000 0x0 0x2000>;
+				reg = <0x0 0x72000 0x0 0x800>;
 				interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};
 
 			sd_emmc_c: mmc@74000 {
 				compatible = "amlogic,meson-gx-mmc", "amlogic,meson-gxbb-mmc";
-				reg = <0x0 0x74000 0x0 0x2000>;
+				reg = <0x0 0x74000 0x0 0x800>;
 				interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};

arch/arm64/boot/dts/amlogic/meson-gxl-mali.dtsi

@@ -6,7 +6,7 @@
 
 &apb {
 	mali: gpu@c0000 {
-		compatible = "amlogic,meson-gxbb-mali", "arm,mali-450";
+		compatible = "amlogic,meson-gxl-mali", "arm,mali-450";
 		reg = <0x0 0xc0000 0x0 0x40000>;
 		interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>,

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts

@@ -234,9 +234,6 @@
 
 	bus-width = <4>;
 	cap-sd-highspeed;
-	sd-uhs-sdr12;
-	sd-uhs-sdr25;
-	sd-uhs-sdr50;
 	max-frequency = <100000000>;
 	disable-wp;
 

arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi

@@ -189,3 +189,10 @@
 &usb0 {
 	status = "okay";
 };
+
+&usb2_phy0 {
+	/*
+	 * HDMI_5V is also used as supply for the USB VBUS.
+	 */
+	phy-supply = <&hdmi_5v>;
+};

arch/arm64/boot/dts/amlogic/meson-gxl.dtsi

@@ -13,14 +13,6 @@
 / {
 	compatible = "amlogic,meson-gxl";
 
-	reserved-memory {
-		/* Alternate 3 MiB reserved for ARM Trusted Firmware (BL31) */
-		secmon_reserved_alt: secmon@5000000 {
-			reg = <0x0 0x05000000 0x0 0x300000>;
-			no-map;
-		};
-	};
-
 	soc {
 		usb0: usb@c9000000 {
 			status = "disabled";

arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi

@@ -118,7 +118,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 281 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <0>;
 
@@ -149,7 +149,7 @@
 
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 0>;
-		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 305 IRQ_TYPE_NONE>;
+		interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
 
 		linux,pci-domain = <4>;
 
@@ -566,7 +566,7 @@
 			reg = <0x66080000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 394 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};
@@ -594,7 +594,7 @@
 			reg = <0x660b0000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 395 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};

arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts

@@ -43,6 +43,10 @@
 	enet-phy-lane-swap;
 };
 
+&sdio0 {
+	mmc-ddr-1_8v;
+};
+
 &uart2 {
 	status = "okay";
 };

arch/arm64/boot/dts/broadcom/stingray/bcm958742t.dts

@@ -42,3 +42,7 @@
 &gphy0 {
 	enet-phy-lane-swap;
 };
+
+&sdio0 {
+	mmc-ddr-1_8v;
+};

arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi

@@ -409,7 +409,7 @@
 			reg = <0x000b0000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 177 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};
@@ -453,7 +453,7 @@
 			reg = <0x000e0000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <GIC_SPI 178 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
 			clock-frequency = <100000>;
 			status = "disabled";
 		};

arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts

@@ -585,6 +585,8 @@
 	vmmc-supply = <&wlan_en>;
 	ti,non-removable;
 	non-removable;
+	cap-power-off-card;
+	keep-power-in-suspend;
 	#address-cells = <0x1>;
 	#size-cells = <0x0>;
 	status = "ok";

arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts

@@ -322,6 +322,8 @@
 		dwmmc_2: dwmmc2@f723f000 {
 			bus-width = <0x4>;
 			non-removable;
+			cap-power-off-card;
+			keep-power-in-suspend;
 			vmmc-supply = <&reg_vdd_3v3>;
 			mmc-pwrseq = <&wl1835_pwrseq>;
 

arch/arm64/boot/dts/marvell/armada-cp110.dtsi

@@ -149,7 +149,7 @@
 
 		CP110_LABEL(icu): interrupt-controller@1e0000 {
 			compatible = "marvell,cp110-icu";
-			reg = <0x1e0000 0x10>;
+			reg = <0x1e0000 0x440>;
 			#interrupt-cells = <3>;
 			interrupt-controller;
 			msi-parent = <&gicp>;

arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi

@@ -75,7 +75,7 @@
 
 		serial@75b1000 {
 			label = "LS-UART0";
-			status = "okay";
+			status = "disabled";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&blsp2_uart2_4pins_default>;
 			pinctrl-1 = <&blsp2_uart2_4pins_sleep>;

arch/arm64/boot/dts/qcom/msm8916.dtsi

@@ -1191,14 +1191,14 @@
 
 				port@0 {
 					reg = <0>;
-					etf_out: endpoint {
+					etf_in: endpoint {
 						slave-mode;
 						remote-endpoint = <&funnel0_out>;
 					};
 				};
 				port@1 {
 					reg = <0>;
-					etf_in: endpoint {
+					etf_out: endpoint {
 						remote-endpoint = <&replicator_in>;
 					};
 				};

arch/arm64/boot/dts/socionext/uniphier-ld11-global.dts

@@ -54,7 +54,7 @@
 	sound {
 		compatible = "audio-graph-card";
 		label = "UniPhier LD11";
-		widgets = "Headphone", "Headphone Jack";
+		widgets = "Headphone", "Headphones";
 		dais = <&i2s_port2
 			&i2s_port3
 			&i2s_port4

arch/arm64/boot/dts/socionext/uniphier-ld20-global.dts

@@ -54,7 +54,7 @@
 	sound {
 		compatible = "audio-graph-card";
 		label = "UniPhier LD20";
-		widgets = "Headphone", "Headphone Jack";
+		widgets = "Headphone", "Headphones";
 		dais = <&i2s_port2
 			&i2s_port3
 			&i2s_port4

arch/arm64/configs/defconfig

@@ -47,6 +47,7 @@ CONFIG_ARCH_MVEBU=y
 CONFIG_ARCH_QCOM=y
 CONFIG_ARCH_ROCKCHIP=y
 CONFIG_ARCH_SEATTLE=y
+CONFIG_ARCH_SYNQUACER=y
 CONFIG_ARCH_RENESAS=y
 CONFIG_ARCH_R8A7795=y
 CONFIG_ARCH_R8A7796=y
@@ -58,7 +59,6 @@ CONFIG_ARCH_R8A77995=y
 CONFIG_ARCH_STRATIX10=y
 CONFIG_ARCH_TEGRA=y
 CONFIG_ARCH_SPRD=y
-CONFIG_ARCH_SYNQUACER=y
 CONFIG_ARCH_THUNDER=y
 CONFIG_ARCH_THUNDER2=y
 CONFIG_ARCH_UNIPHIER=y
@@ -67,25 +67,23 @@ CONFIG_ARCH_XGENE=y
 CONFIG_ARCH_ZX=y
 CONFIG_ARCH_ZYNQMP=y
 CONFIG_PCI=y
-CONFIG_HOTPLUG_PCI_PCIE=y
 CONFIG_PCI_IOV=y
 CONFIG_HOTPLUG_PCI=y
 CONFIG_HOTPLUG_PCI_ACPI=y
-CONFIG_PCI_LAYERSCAPE=y
-CONFIG_PCI_HISI=y
-CONFIG_PCIE_QCOM=y
-CONFIG_PCIE_KIRIN=y
-CONFIG_PCIE_ARMADA_8K=y
-CONFIG_PCIE_HISI_STB=y
 CONFIG_PCI_AARDVARK=y
 CONFIG_PCI_TEGRA=y
 CONFIG_PCIE_RCAR=y
-CONFIG_PCIE_ROCKCHIP=y
-CONFIG_PCIE_ROCKCHIP_HOST=m
 CONFIG_PCI_HOST_GENERIC=y
 CONFIG_PCI_XGENE=y
 CONFIG_PCI_HOST_THUNDER_PEM=y
 CONFIG_PCI_HOST_THUNDER_ECAM=y
+CONFIG_PCIE_ROCKCHIP_HOST=m
+CONFIG_PCI_LAYERSCAPE=y
+CONFIG_PCI_HISI=y
+CONFIG_PCIE_QCOM=y
+CONFIG_PCIE_ARMADA_8K=y
+CONFIG_PCIE_KIRIN=y
+CONFIG_PCIE_HISI_STB=y
 CONFIG_ARM64_VA_BITS_48=y
 CONFIG_SCHED_MC=y
 CONFIG_NUMA=y
@@ -104,8 +102,6 @@ CONFIG_HIBERNATION=y
 CONFIG_WQ_POWER_EFFICIENT_DEFAULT=y
 CONFIG_ARM_CPUIDLE=y
 CONFIG_CPU_FREQ=y
-CONFIG_CPU_FREQ_GOV_ATTR_SET=y
-CONFIG_CPU_FREQ_GOV_COMMON=y
 CONFIG_CPU_FREQ_STAT=y
 CONFIG_CPU_FREQ_GOV_POWERSAVE=m
 CONFIG_CPU_FREQ_GOV_USERSPACE=y
@@ -113,11 +109,11 @@ CONFIG_CPU_FREQ_GOV_ONDEMAND=y
 CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
 CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
 CONFIG_CPUFREQ_DT=y
+CONFIG_ACPI_CPPC_CPUFREQ=m
 CONFIG_ARM_ARMADA_37XX_CPUFREQ=y
 CONFIG_ARM_BIG_LITTLE_CPUFREQ=y
 CONFIG_ARM_SCPI_CPUFREQ=y
 CONFIG_ARM_TEGRA186_CPUFREQ=y
-CONFIG_ACPI_CPPC_CPUFREQ=m
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -236,11 +232,6 @@ CONFIG_SMSC911X=y
 CONFIG_SNI_AVE=y
 CONFIG_SNI_NETSEC=y
 CONFIG_STMMAC_ETH=m
-CONFIG_DWMAC_IPQ806X=m
-CONFIG_DWMAC_MESON=m
-CONFIG_DWMAC_ROCKCHIP=m
-CONFIG_DWMAC_SUNXI=m
-CONFIG_DWMAC_SUN8I=m
 CONFIG_MDIO_BUS_MUX_MMIOREG=y
 CONFIG_AT803X_PHY=m
 CONFIG_MARVELL_PHY=m
@@ -269,8 +260,8 @@ CONFIG_WL18XX=m
 CONFIG_WLCORE_SDIO=m
 CONFIG_INPUT_EVDEV=y
 CONFIG_KEYBOARD_ADC=m
-CONFIG_KEYBOARD_CROS_EC=y
 CONFIG_KEYBOARD_GPIO=y
+CONFIG_KEYBOARD_CROS_EC=y
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ATMEL_MXT=m
 CONFIG_INPUT_MISC=y
@@ -296,17 +287,13 @@ CONFIG_SERIAL_SAMSUNG=y
 CONFIG_SERIAL_SAMSUNG_CONSOLE=y
 CONFIG_SERIAL_TEGRA=y
 CONFIG_SERIAL_SH_SCI=y
-CONFIG_SERIAL_SH_SCI_NR_UARTS=11
-CONFIG_SERIAL_SH_SCI_CONSOLE=y
 CONFIG_SERIAL_MSM=y
 CONFIG_SERIAL_MSM_CONSOLE=y
 CONFIG_SERIAL_XILINX_PS_UART=y
 CONFIG_SERIAL_XILINX_PS_UART_CONSOLE=y
 CONFIG_SERIAL_MVEBU_UART=y
 CONFIG_SERIAL_DEV_BUS=y
-CONFIG_SERIAL_DEV_CTRL_TTYPORT=y
 CONFIG_VIRTIO_CONSOLE=y
-CONFIG_I2C_HID=m
 CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_MUX=y
 CONFIG_I2C_MUX_PCA954x=y
@@ -325,26 +312,26 @@ CONFIG_I2C_RCAR=y
 CONFIG_I2C_CROS_EC_TUNNEL=y
 CONFIG_SPI=y
 CONFIG_SPI_ARMADA_3700=y
-CONFIG_SPI_MESON_SPICC=m
-CONFIG_SPI_MESON_SPIFC=m
 CONFIG_SPI_BCM2835=m
 CONFIG_SPI_BCM2835AUX=m
+CONFIG_SPI_MESON_SPICC=m
+CONFIG_SPI_MESON_SPIFC=m
 CONFIG_SPI_ORION=y
 CONFIG_SPI_PL022=y
-CONFIG_SPI_QUP=y
 CONFIG_SPI_ROCKCHIP=y
+CONFIG_SPI_QUP=y
 CONFIG_SPI_S3C64XX=y
 CONFIG_SPI_SPIDEV=m
 CONFIG_SPMI=y
-CONFIG_PINCTRL_IPQ8074=y
 CONFIG_PINCTRL_SINGLE=y
 CONFIG_PINCTRL_MAX77620=y
+CONFIG_PINCTRL_IPQ8074=y
 CONFIG_PINCTRL_MSM8916=y
 CONFIG_PINCTRL_MSM8994=y
 CONFIG_PINCTRL_MSM8996=y
-CONFIG_PINCTRL_MT7622=y
 CONFIG_PINCTRL_QDF2XXX=y
 CONFIG_PINCTRL_QCOM_SPMI_PMIC=y
+CONFIG_PINCTRL_MT7622=y
 CONFIG_GPIO_DWAPB=y
 CONFIG_GPIO_MB86S7X=y
 CONFIG_GPIO_PL061=y
@@ -368,13 +355,13 @@ CONFIG_SENSORS_INA2XX=m
 CONFIG_THERMAL_GOV_POWER_ALLOCATOR=y
 CONFIG_CPU_THERMAL=y
 CONFIG_THERMAL_EMULATION=y
+CONFIG_ROCKCHIP_THERMAL=m
+CONFIG_RCAR_GEN3_THERMAL=y
 CONFIG_ARMADA_THERMAL=y
 CONFIG_BRCMSTB_THERMAL=m
 CONFIG_EXYNOS_THERMAL=y
-CONFIG_RCAR_GEN3_THERMAL=y
-CONFIG_QCOM_TSENS=y
-CONFIG_ROCKCHIP_THERMAL=m
 CONFIG_TEGRA_BPMP_THERMAL=m
+CONFIG_QCOM_TSENS=y
 CONFIG_UNIPHIER_THERMAL=y
 CONFIG_WATCHDOG=y
 CONFIG_S3C2410_WATCHDOG=y
@@ -395,9 +382,9 @@ CONFIG_MFD_MAX77620=y
 CONFIG_MFD_SPMI_PMIC=y
 CONFIG_MFD_RK808=y
 CONFIG_MFD_SEC_CORE=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_AXP20X=y
 CONFIG_REGULATOR_FAN53555=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_GPIO=y
 CONFIG_REGULATOR_HI6421V530=y
 CONFIG_REGULATOR_HI655X=y
@@ -407,16 +394,15 @@ CONFIG_REGULATOR_QCOM_SMD_RPM=y
 CONFIG_REGULATOR_QCOM_SPMI=y
 CONFIG_REGULATOR_RK808=y
 CONFIG_REGULATOR_S2MPS11=y
+CONFIG_RC_CORE=m
+CONFIG_RC_DECODERS=y
+CONFIG_RC_DEVICES=y
+CONFIG_IR_MESON=m
 CONFIG_MEDIA_SUPPORT=m
 CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_MEDIA_ANALOG_TV_SUPPORT=y
 CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
 CONFIG_MEDIA_CONTROLLER=y
-CONFIG_MEDIA_RC_SUPPORT=y
-CONFIG_RC_CORE=m
-CONFIG_RC_DEVICES=y
-CONFIG_RC_DECODERS=y
-CONFIG_IR_MESON=m
 CONFIG_VIDEO_V4L2_SUBDEV_API=y
 # CONFIG_DVB_NET is not set
 CONFIG_V4L_MEM2MEM_DRIVERS=y
@@ -441,8 +427,7 @@ CONFIG_ROCKCHIP_DW_HDMI=y
 CONFIG_ROCKCHIP_DW_MIPI_DSI=y
 CONFIG_ROCKCHIP_INNO_HDMI=y
 CONFIG_DRM_RCAR_DU=m
-CONFIG_DRM_RCAR_LVDS=y
-CONFIG_DRM_RCAR_VSP=y
+CONFIG_DRM_RCAR_LVDS=m
 CONFIG_DRM_TEGRA=m
 CONFIG_DRM_PANEL_SIMPLE=m
 CONFIG_DRM_I2C_ADV7511=m
@@ -455,7 +440,6 @@ CONFIG_FB_ARMCLCD=y
 CONFIG_BACKLIGHT_GENERIC=m
 CONFIG_BACKLIGHT_PWM=m
 CONFIG_BACKLIGHT_LP855X=m
-CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_LOGO=y
 # CONFIG_LOGO_LINUX_MONO is not set
 # CONFIG_LOGO_LINUX_VGA16 is not set
@@ -468,6 +452,7 @@ CONFIG_SND_SOC_RCAR=m
 CONFIG_SND_SOC_AK4613=m
 CONFIG_SND_SIMPLE_CARD=m
 CONFIG_SND_AUDIO_GRAPH_CARD=m
+CONFIG_I2C_HID=m
 CONFIG_USB=y
 CONFIG_USB_OTG=y
 CONFIG_USB_XHCI_HCD=y
@@ -501,12 +486,12 @@ CONFIG_MMC_BLOCK_MINORS=32
 CONFIG_MMC_ARMMMCI=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ACPI=y
-CONFIG_MMC_SDHCI_F_SDH30=y
 CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_SDHCI_OF_ARASAN=y
 CONFIG_MMC_SDHCI_OF_ESDHC=y
 CONFIG_MMC_SDHCI_CADENCE=y
 CONFIG_MMC_SDHCI_TEGRA=y
+CONFIG_MMC_SDHCI_F_SDH30=y
 CONFIG_MMC_MESON_GX=y
 CONFIG_MMC_SDHCI_MSM=y
 CONFIG_MMC_SPI=y
@@ -524,11 +509,11 @@ CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_GPIO=y
 CONFIG_LEDS_PWM=y
 CONFIG_LEDS_SYSCON=y
+CONFIG_LEDS_TRIGGER_DISK=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
 CONFIG_LEDS_TRIGGER_PANIC=y
-CONFIG_LEDS_TRIGGER_DISK=y
 CONFIG_EDAC=y
 CONFIG_EDAC_GHES=y
 CONFIG_RTC_CLASS=y
@@ -537,13 +522,13 @@ CONFIG_RTC_DRV_RK808=m
 CONFIG_RTC_DRV_S5M=y
 CONFIG_RTC_DRV_DS3232=y
 CONFIG_RTC_DRV_EFI=y
+CONFIG_RTC_DRV_CROS_EC=y
 CONFIG_RTC_DRV_S3C=y
 CONFIG_RTC_DRV_PL031=y
 CONFIG_RTC_DRV_SUN6I=y
 CONFIG_RTC_DRV_ARMADA38X=y
 CONFIG_RTC_DRV_TEGRA=y
 CONFIG_RTC_DRV_XGENE=y
-CONFIG_RTC_DRV_CROS_EC=y
 CONFIG_DMADEVICES=y
 CONFIG_DMA_BCM2835=m
 CONFIG_K3_DMA=y
@@ -579,7 +564,6 @@ CONFIG_HWSPINLOCK_QCOM=y
 CONFIG_ARM_MHU=y
 CONFIG_PLATFORM_MHU=y
 CONFIG_BCM2835_MBOX=y
-CONFIG_HI6220_MBOX=y
 CONFIG_QCOM_APCS_IPC=y
 CONFIG_ROCKCHIP_IOMMU=y
 CONFIG_TEGRA_IOMMU_SMMU=y
@@ -602,7 +586,6 @@ CONFIG_DEVFREQ_GOV_SIMPLE_ONDEMAND=y
 CONFIG_EXTCON_USB_GPIO=y
 CONFIG_EXTCON_USBC_CROS_EC=y
 CONFIG_MEMORY=y
-CONFIG_TEGRA_MC=y
 CONFIG_IIO=y
 CONFIG_EXYNOS_ADC=y
 CONFIG_ROCKCHIP_SARADC=m
@@ -618,27 +601,27 @@ CONFIG_PWM_RCAR=m
 CONFIG_PWM_ROCKCHIP=y
 CONFIG_PWM_SAMSUNG=y
 CONFIG_PWM_TEGRA=m
+CONFIG_PHY_XGENE=y
+CONFIG_PHY_SUN4I_USB=y
+CONFIG_PHY_HI6220_USB=y
 CONFIG_PHY_HISTB_COMBPHY=y
 CONFIG_PHY_HISI_INNO_USB2=y
-CONFIG_PHY_RCAR_GEN3_USB2=y
-CONFIG_PHY_RCAR_GEN3_USB3=m
-CONFIG_PHY_HI6220_USB=y
-CONFIG_PHY_QCOM_USB_HS=y
-CONFIG_PHY_SUN4I_USB=y
 CONFIG_PHY_MVEBU_CP110_COMPHY=y
 CONFIG_PHY_QCOM_QMP=m
-CONFIG_PHY_ROCKCHIP_INNO_USB2=y
+CONFIG_PHY_QCOM_USB_HS=y
+CONFIG_PHY_RCAR_GEN3_USB2=y
+CONFIG_PHY_RCAR_GEN3_USB3=m
 CONFIG_PHY_ROCKCHIP_EMMC=y
+CONFIG_PHY_ROCKCHIP_INNO_USB2=y
 CONFIG_PHY_ROCKCHIP_PCIE=m
 CONFIG_PHY_ROCKCHIP_TYPEC=y
-CONFIG_PHY_XGENE=y
 CONFIG_PHY_TEGRA_XUSB=y
 CONFIG_QCOM_L2_PMU=y
 CONFIG_QCOM_L3_PMU=y
-CONFIG_MESON_EFUSE=m
 CONFIG_QCOM_QFPROM=y
 CONFIG_ROCKCHIP_EFUSE=y
 CONFIG_UNIPHIER_EFUSE=y
+CONFIG_MESON_EFUSE=m
 CONFIG_TEE=y
 CONFIG_OPTEE=y
 CONFIG_ARM_SCPI_PROTOCOL=y
@@ -647,7 +630,6 @@ CONFIG_EFI_CAPSULE_LOADER=y
 CONFIG_ACPI=y
 CONFIG_ACPI_APEI=y
 CONFIG_ACPI_APEI_GHES=y
-CONFIG_ACPI_APEI_PCIEAER=y
 CONFIG_ACPI_APEI_MEMORY_FAILURE=y
 CONFIG_ACPI_APEI_EINJ=y
 CONFIG_EXT2_FS=y
@@ -682,7 +664,6 @@ CONFIG_DEBUG_INFO=y
 CONFIG_DEBUG_FS=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
-CONFIG_LOCKUP_DETECTOR=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_DEBUG_PREEMPT is not set
 # CONFIG_FTRACE is not set
@@ -691,20 +672,15 @@ CONFIG_SECURITY=y
 CONFIG_CRYPTO_ECHAINIV=y
 CONFIG_CRYPTO_ANSI_CPRNG=y
 CONFIG_ARM64_CRYPTO=y
-CONFIG_CRYPTO_SHA256_ARM64=m
-CONFIG_CRYPTO_SHA512_ARM64=m
 CONFIG_CRYPTO_SHA1_ARM64_CE=y
 CONFIG_CRYPTO_SHA2_ARM64_CE=y
+CONFIG_CRYPTO_SHA512_ARM64_CE=m
+CONFIG_CRYPTO_SHA3_ARM64=m
+CONFIG_CRYPTO_SM3_ARM64_CE=m
 CONFIG_CRYPTO_GHASH_ARM64_CE=y
 CONFIG_CRYPTO_CRCT10DIF_ARM64_CE=m
 CONFIG_CRYPTO_CRC32_ARM64_CE=m
-CONFIG_CRYPTO_AES_ARM64=m
-CONFIG_CRYPTO_AES_ARM64_CE=m
 CONFIG_CRYPTO_AES_ARM64_CE_CCM=y
 CONFIG_CRYPTO_AES_ARM64_CE_BLK=y
-CONFIG_CRYPTO_AES_ARM64_NEON_BLK=m
 CONFIG_CRYPTO_CHACHA20_NEON=m
 CONFIG_CRYPTO_AES_ARM64_BS=m
-CONFIG_CRYPTO_SHA512_ARM64_CE=m
-CONFIG_CRYPTO_SHA3_ARM64=m
-CONFIG_CRYPTO_SM3_ARM64_CE=m

arch/arm64/include/asm/alternative.h

@@ -28,7 +28,12 @@ typedef void (*alternative_cb_t)(struct alt_instr *alt,
 				 __le32 *origptr, __le32 *updptr, int nr_inst);
 
 void __init apply_alternatives_all(void);
-void apply_alternatives(void *start, size_t length);
+
+#ifdef CONFIG_MODULES
+void apply_alternatives_module(void *start, size_t length);
+#else
+static inline void apply_alternatives_module(void *start, size_t length) { }
+#endif
 
 #define ALTINSTR_ENTRY(feature,cb)					      \
 	" .word 661b - .\n"				/* label           */ \

arch/arm64/include/asm/pgtable.h

@@ -224,10 +224,8 @@ static inline void set_pte(pte_t *ptep, pte_t pte)
 	 * Only if the new pte is valid and kernel, otherwise TLB maintenance
 	 * or update_mmu_cache() have the necessary barriers.
 	 */
-	if (pte_valid_not_user(pte)) {
+	if (pte_valid_not_user(pte))
 		dsb(ishst);
-		isb();
-	}
 }
 
 extern void __sync_icache_dcache(pte_t pteval);
@@ -434,7 +432,6 @@ static inline void set_pmd(pmd_t *pmdp, pmd_t pmd)
 {
 	WRITE_ONCE(*pmdp, pmd);
 	dsb(ishst);
-	isb();
 }
 
 static inline void pmd_clear(pmd_t *pmdp)
@@ -485,7 +482,6 @@ static inline void set_pud(pud_t *pudp, pud_t pud)
 {
 	WRITE_ONCE(*pudp, pud);
 	dsb(ishst);
-	isb();
 }
 
 static inline void pud_clear(pud_t *pudp)

arch/arm64/include/asm/simd.h

@@ -29,20 +29,15 @@ DECLARE_PER_CPU(bool, kernel_neon_busy);
 static __must_check inline bool may_use_simd(void)
 {
 	/*
-	 * The raw_cpu_read() is racy if called with preemption enabled.
-	 * This is not a bug: kernel_neon_busy is only set when
-	 * preemption is disabled, so we cannot migrate to another CPU
-	 * while it is set, nor can we migrate to a CPU where it is set.
-	 * So, if we find it clear on some CPU then we're guaranteed to
-	 * find it clear on any CPU we could migrate to.
-	 *
-	 * If we are in between kernel_neon_begin()...kernel_neon_end(),
-	 * the flag will be set, but preemption is also disabled, so we
-	 * can't migrate to another CPU and spuriously see it become
-	 * false.
+	 * kernel_neon_busy is only set while preemption is disabled,
+	 * and is clear whenever preemption is enabled. Since
+	 * this_cpu_read() is atomic w.r.t. preemption, kernel_neon_busy
+	 * cannot change under our feet -- if it's set we cannot be
+	 * migrated, and if it's clear we cannot be migrated to a CPU
+	 * where it is set.
 	 */
 	return !in_irq() && !irqs_disabled() && !in_nmi() &&
-		!raw_cpu_read(kernel_neon_busy);
+		!this_cpu_read(kernel_neon_busy);
 }
 
 #else /* ! CONFIG_KERNEL_MODE_NEON */

arch/arm64/kernel/alternative.c

@@ -122,7 +122,30 @@ static void patch_alternative(struct alt_instr *alt,
 	}
 }
 
-static void __apply_alternatives(void *alt_region, bool use_linear_alias)
+/*
+ * We provide our own, private D-cache cleaning function so that we don't
+ * accidentally call into the cache.S code, which is patched by us at
+ * runtime.
+ */
+static void clean_dcache_range_nopatch(u64 start, u64 end)
+{
+	u64 cur, d_size, ctr_el0;
+
+	ctr_el0 = read_sanitised_ftr_reg(SYS_CTR_EL0);
+	d_size = 4 << cpuid_feature_extract_unsigned_field(ctr_el0,
+							   CTR_DMINLINE_SHIFT);
+	cur = start & ~(d_size - 1);
+	do {
+		/*
+		 * We must clean+invalidate to the PoC in order to avoid
+		 * Cortex-A53 errata 826319, 827319, 824069 and 819472
+		 * (this corresponds to ARM64_WORKAROUND_CLEAN_CACHE)
+		 */
+		asm volatile("dc civac, %0" : : "r" (cur) : "memory");
+	} while (cur += d_size, cur < end);
+}
+
+static void __apply_alternatives(void *alt_region, bool is_module)
 {
 	struct alt_instr *alt;
 	struct alt_region *region = alt_region;
@@ -145,7 +168,7 @@ static void __apply_alternatives(void *alt_region, bool use_linear_alias)
 		pr_info_once("patching kernel code\n");
 
 		origptr = ALT_ORIG_PTR(alt);
-		updptr = use_linear_alias ? lm_alias(origptr) : origptr;
+		updptr = is_module ? origptr : lm_alias(origptr);
 		nr_inst = alt->orig_len / AARCH64_INSN_SIZE;
 
 		if (alt->cpufeature < ARM64_CB_PATCH)
@@ -155,8 +178,20 @@ static void __apply_alternatives(void *alt_region, bool use_linear_alias)
 
 		alt_cb(alt, origptr, updptr, nr_inst);
 
-		flush_icache_range((uintptr_t)origptr,
-				   (uintptr_t)(origptr + nr_inst));
+		if (!is_module) {
+			clean_dcache_range_nopatch((u64)origptr,
+						   (u64)(origptr + nr_inst));
+		}
+	}
+
+	/*
+	 * The core module code takes care of cache maintenance in
+	 * flush_module_icache().
+	 */
+	if (!is_module) {
+		dsb(ish);
+		__flush_icache_all();
+		isb();
 	}
 }
 
@@ -178,7 +213,7 @@ static int __apply_alternatives_multi_stop(void *unused)
 		isb();
 	} else {
 		BUG_ON(alternatives_applied);
-		__apply_alternatives(&region, true);
+		__apply_alternatives(&region, false);
 		/* Barriers provided by the cache flushing */
 		WRITE_ONCE(alternatives_applied, 1);
 	}
@@ -192,12 +227,14 @@ void __init apply_alternatives_all(void)
 	stop_machine(__apply_alternatives_multi_stop, NULL, cpu_online_mask);
 }
 
-void apply_alternatives(void *start, size_t length)
+#ifdef CONFIG_MODULES
+void apply_alternatives_module(void *start, size_t length)
 {
 	struct alt_region region = {
 		.begin	= start,
 		.end	= start + length,
 	};
 
-	__apply_alternatives(&region, false);
+	__apply_alternatives(&region, true);
 }
+#endif

arch/arm64/kernel/module.c

@@ -448,9 +448,8 @@ int module_finalize(const Elf_Ehdr *hdr,
 	const char *secstrs = (void *)hdr + sechdrs[hdr->e_shstrndx].sh_offset;
 
 	for (s = sechdrs, se = sechdrs + hdr->e_shnum; s < se; s++) {
-		if (strcmp(".altinstructions", secstrs + s->sh_name) == 0) {
-			apply_alternatives((void *)s->sh_addr, s->sh_size);
-		}
+		if (strcmp(".altinstructions", secstrs + s->sh_name) == 0)
+			apply_alternatives_module((void *)s->sh_addr, s->sh_size);
 #ifdef CONFIG_ARM64_MODULE_PLTS
 		if (IS_ENABLED(CONFIG_DYNAMIC_FTRACE) &&
 		    !strcmp(".text.ftrace_trampoline", secstrs + s->sh_name))

arch/m68k/include/asm/mcf_pgalloc.h

@@ -44,6 +44,7 @@ extern inline pmd_t *pmd_alloc_kernel(pgd_t *pgd, unsigned long address)
 static inline void __pte_free_tlb(struct mmu_gather *tlb, pgtable_t page,
 				  unsigned long address)
 {
+	pgtable_page_dtor(page);
 	__free_page(page);
 }
 
@@ -74,8 +75,9 @@ static inline struct page *pte_alloc_one(struct mm_struct *mm,
 	return page;
 }
 
-extern inline void pte_free(struct mm_struct *mm, struct page *page)
+static inline void pte_free(struct mm_struct *mm, struct page *page)
 {
+	pgtable_page_dtor(page);
 	__free_page(page);
 }
 

arch/microblaze/Kconfig.debug

@@ -8,11 +8,4 @@ config TRACE_IRQFLAGS_SUPPORT
 
 source "lib/Kconfig.debug"
 
-config HEART_BEAT
-	bool "Heart beat function for kernel"
-	default n
-	help
-	  This option turns on/off heart beat kernel functionality.
-	  First GPIO node is taken.
-
 endmenu

arch/microblaze/include/asm/setup.h

@@ -19,15 +19,10 @@ extern char cmd_line[COMMAND_LINE_SIZE];
 
 extern char *klimit;
 
-void microblaze_heartbeat(void);
-void microblaze_setup_heartbeat(void);
-
 #   ifdef CONFIG_MMU
 extern void mmu_reset(void);
 #   endif /* CONFIG_MMU */
 
-extern void of_platform_reset_gpio_probe(void);
-
 void time_init(void);
 void init_IRQ(void);
 void machine_early_init(const char *cmdline, unsigned int ram,

arch/microblaze/include/asm/unistd.h

@@ -38,6 +38,6 @@
 
 #endif /* __ASSEMBLY__ */
 
-#define __NR_syscalls         399
+#define __NR_syscalls         401
 
 #endif /* _ASM_MICROBLAZE_UNISTD_H */

arch/microblaze/include/uapi/asm/unistd.h

@@ -415,5 +415,7 @@
 #define __NR_pkey_alloc		396
 #define __NR_pkey_free		397
 #define __NR_statx		398
+#define __NR_io_pgetevents	399
+#define __NR_rseq		400
 
 #endif /* _UAPI_ASM_MICROBLAZE_UNISTD_H */

arch/microblaze/kernel/Makefile

@@ -8,7 +8,6 @@ ifdef CONFIG_FUNCTION_TRACER
 CFLAGS_REMOVE_timer.o = -pg
 CFLAGS_REMOVE_intc.o = -pg
 CFLAGS_REMOVE_early_printk.o = -pg
-CFLAGS_REMOVE_heartbeat.o = -pg
 CFLAGS_REMOVE_ftrace.o = -pg
 CFLAGS_REMOVE_process.o = -pg
 endif
@@ -17,12 +16,11 @@ extra-y := head.o vmlinux.lds
 
 obj-y += dma.o exceptions.o \
 	hw_exception_handler.o irq.o \
-	platform.o process.o prom.o ptrace.o \
+	process.o prom.o ptrace.o \
 	reset.o setup.o signal.o sys_microblaze.o timer.o traps.o unwind.o
 
 obj-y += cpu/
 
-obj-$(CONFIG_HEART_BEAT)	+= heartbeat.o
 obj-$(CONFIG_MODULES)		+= microblaze_ksyms.o module.o
 obj-$(CONFIG_MMU)		+= misc.o
 obj-$(CONFIG_STACKTRACE)	+= stacktrace.o

arch/microblaze/kernel/heartbeat.c

@@ -1,72 +0,0 @@
-/*
- * Copyright (C) 2007-2009 Michal Simek <monstr@monstr.eu>
- * Copyright (C) 2007-2009 PetaLogix
- * Copyright (C) 2006 Atmark Techno, Inc.
- *
- * This file is subject to the terms and conditions of the GNU General Public
- * License. See the file "COPYING" in the main directory of this archive
- * for more details.
- */
-
-#include <linux/sched.h>
-#include <linux/sched/loadavg.h>
-#include <linux/io.h>
-
-#include <asm/setup.h>
-#include <asm/page.h>
-#include <asm/prom.h>
-
-static unsigned int base_addr;
-
-void microblaze_heartbeat(void)
-{
-	static unsigned int cnt, period, dist;
-
-	if (base_addr) {
-		if (cnt == 0 || cnt == dist)
-			out_be32(base_addr, 1);
-		else if (cnt == 7 || cnt == dist + 7)
-			out_be32(base_addr, 0);
-
-		if (++cnt > period) {
-			cnt = 0;
-			/*
-			 * The hyperbolic function below modifies the heartbeat
-			 * period length in dependency of the current (5min)
-			 * load. It goes through the points f(0)=126, f(1)=86,
-			 * f(5)=51, f(inf)->30.
-			 */
-			period = ((672 << FSHIFT) / (5 * avenrun[0] +
-						(7 << FSHIFT))) + 30;
-			dist = period / 4;
-		}
-	}
-}
-
-void microblaze_setup_heartbeat(void)
-{
-	struct device_node *gpio = NULL;
-	int *prop;
-	int j;
-	const char * const gpio_list[] = {
-		"xlnx,xps-gpio-1.00.a",
-		NULL
-	};
-
-	for (j = 0; gpio_list[j] != NULL; j++) {
-		gpio = of_find_compatible_node(NULL, NULL, gpio_list[j]);
-		if (gpio)
-			break;
-	}
-
-	if (gpio) {
-		base_addr = be32_to_cpup(of_get_property(gpio, "reg", NULL));
-		base_addr = (unsigned long) ioremap(base_addr, PAGE_SIZE);
-		pr_notice("Heartbeat GPIO at 0x%x\n", base_addr);
-
-		/* GPIO is configured as output */
-		prop = (int *) of_get_property(gpio, "xlnx,is-bidir", NULL);
-		if (prop)
-			out_be32(base_addr + 4, 0);
-	}
-}

arch/microblaze/kernel/platform.c

@@ -1,29 +0,0 @@
-/*
- * Copyright 2008 Michal Simek <monstr@monstr.eu>
- *
- * based on virtex.c file
- *
- * Copyright 2007 Secret Lab Technologies Ltd.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#include <linux/init.h>
-#include <linux/of_platform.h>
-#include <asm/setup.h>
-
-static struct of_device_id xilinx_of_bus_ids[] __initdata = {
-	{ .compatible = "simple-bus", },
-	{ .compatible = "xlnx,compound", },
-	{}
-};
-
-static int __init microblaze_device_probe(void)
-{
-	of_platform_bus_probe(NULL, xilinx_of_bus_ids, NULL);
-	of_platform_reset_gpio_probe();
-	return 0;
-}
-device_initcall(microblaze_device_probe);

arch/microblaze/kernel/reset.c

@@ -18,7 +18,7 @@
 static int handle; /* reset pin handle */
 static unsigned int reset_val;
 
-void of_platform_reset_gpio_probe(void)
+static int of_platform_reset_gpio_probe(void)
 {
 	int ret;
 	handle = of_get_named_gpio(of_find_node_by_path("/"),
@@ -27,13 +27,13 @@ void of_platform_reset_gpio_probe(void)
 	if (!gpio_is_valid(handle)) {
 		pr_info("Skipping unavailable RESET gpio %d (%s)\n",
 				handle, "reset");
-		return;
+		return -ENODEV;
 	}
 
 	ret = gpio_request(handle, "reset");
 	if (ret < 0) {
 		pr_info("GPIO pin is already allocated\n");
-		return;
+		return ret;
 	}
 
 	/* get current setup value */
@@ -51,11 +51,12 @@ void of_platform_reset_gpio_probe(void)
 
 	pr_info("RESET: Registered gpio device: %d, current val: %d\n",
 							handle, reset_val);
-	return;
+	return 0;
 err:
 	gpio_free(handle);
-	return;
+	return ret;
 }
+device_initcall(of_platform_reset_gpio_probe);
 
 
 static void gpio_system_reset(void)

arch/microblaze/kernel/syscall_table.S

@@ -400,3 +400,5 @@ ENTRY(sys_call_table)
 	.long sys_pkey_alloc
 	.long sys_pkey_free
 	.long sys_statx
+	.long sys_io_pgetevents
+	.long sys_rseq

arch/microblaze/kernel/timer.c

@@ -156,9 +156,6 @@ static inline void timer_ack(void)
 static irqreturn_t timer_interrupt(int irq, void *dev_id)
 {
 	struct clock_event_device *evt = &clockevent_xilinx_timer;
-#ifdef CONFIG_HEART_BEAT
-	microblaze_heartbeat();
-#endif
 	timer_ack();
 	evt->event_handler(evt);
 	return IRQ_HANDLED;
@@ -318,10 +315,6 @@ static int __init xilinx_timer_init(struct device_node *timer)
 		return ret;
 	}
 
-#ifdef CONFIG_HEART_BEAT
-	microblaze_setup_heartbeat();
-#endif
-
 	ret = xilinx_clocksource_init();
 	if (ret)
 		return ret;

arch/mips/kernel/process.c

@@ -29,6 +29,7 @@
 #include <linux/kallsyms.h>
 #include <linux/random.h>
 #include <linux/prctl.h>
+#include <linux/nmi.h>
 
 #include <asm/asm.h>
 #include <asm/bootinfo.h>
@@ -655,28 +656,42 @@ unsigned long arch_align_stack(unsigned long sp)
 	return sp & ALMASK;
 }
 
-static void arch_dump_stack(void *info)
+static DEFINE_PER_CPU(call_single_data_t, backtrace_csd);
+static struct cpumask backtrace_csd_busy;
+
+static void handle_backtrace(void *info)
 {
-	struct pt_regs *regs;
+	nmi_cpu_backtrace(get_irq_regs());
+	cpumask_clear_cpu(smp_processor_id(), &backtrace_csd_busy);
+}
 
-	regs = get_irq_regs();
+static void raise_backtrace(cpumask_t *mask)
+{
+	call_single_data_t *csd;
+	int cpu;
 
-	if (regs)
-		show_regs(regs);
+	for_each_cpu(cpu, mask) {
+		/*
+		 * If we previously sent an IPI to the target CPU & it hasn't
+		 * cleared its bit in the busy cpumask then it didn't handle
+		 * our previous IPI & it's not safe for us to reuse the
+		 * call_single_data_t.
+		 */
+		if (cpumask_test_and_set_cpu(cpu, &backtrace_csd_busy)) {
+			pr_warn("Unable to send backtrace IPI to CPU%u - perhaps it hung?\n",
+				cpu);
+			continue;
+		}
 
-	dump_stack();
+		csd = &per_cpu(backtrace_csd, cpu);
+		csd->func = handle_backtrace;
+		smp_call_function_single_async(cpu, csd);
+	}
 }
 
 void arch_trigger_cpumask_backtrace(const cpumask_t *mask, bool exclude_self)
 {
-	long this_cpu = get_cpu();
-
-	if (cpumask_test_cpu(this_cpu, mask) && !exclude_self)
-		dump_stack();
-
-	smp_call_function_many(mask, arch_dump_stack, NULL, 1);
-
-	put_cpu();
+	nmi_trigger_cpumask_backtrace(mask, exclude_self, raise_backtrace);
 }
 
 int mips_get_process_fp_mode(struct task_struct *task)

arch/mips/kernel/signal.c

@@ -801,7 +801,7 @@ static void handle_signal(struct ksignal *ksig, struct pt_regs *regs)
 		regs->regs[0] = 0;		/* Don't deal with this again.	*/
 	}
 
-	rseq_signal_deliver(regs);
+	rseq_signal_deliver(ksig, regs);
 
 	if (sig_uses_siginfo(&ksig->ka, abi))
 		ret = abi->setup_rt_frame(vdso + abi->vdso->off_rt_sigreturn,
@@ -870,7 +870,7 @@ asmlinkage void do_notify_resume(struct pt_regs *regs, void *unused,
 	if (thread_info_flags & _TIF_NOTIFY_RESUME) {
 		clear_thread_flag(TIF_NOTIFY_RESUME);
 		tracehook_notify_resume(regs);
-		rseq_handle_notify_resume(regs);
+		rseq_handle_notify_resume(NULL, regs);
 	}
 
 	user_enter();

arch/mips/kernel/traps.c

@@ -351,6 +351,7 @@ static void __show_regs(const struct pt_regs *regs)
 void show_regs(struct pt_regs *regs)
 {
 	__show_regs((struct pt_regs *)regs);
+	dump_stack();
 }
 
 void show_registers(struct pt_regs *regs)

arch/mips/mm/ioremap.c

@@ -9,6 +9,7 @@
 #include <linux/export.h>
 #include <asm/addrspace.h>
 #include <asm/byteorder.h>
+#include <linux/ioport.h>
 #include <linux/sched.h>
 #include <linux/slab.h>
 #include <linux/vmalloc.h>
@@ -98,6 +99,20 @@ static int remap_area_pages(unsigned long address, phys_addr_t phys_addr,
 	return error;
 }
 
+static int __ioremap_check_ram(unsigned long start_pfn, unsigned long nr_pages,
+			       void *arg)
+{
+	unsigned long i;
+
+	for (i = 0; i < nr_pages; i++) {
+		if (pfn_valid(start_pfn + i) &&
+		    !PageReserved(pfn_to_page(start_pfn + i)))
+			return 1;
+	}
+
+	return 0;
+}
+
 /*
  * Generic mapping function (not visible outside):
  */
@@ -116,8 +131,8 @@ static int remap_area_pages(unsigned long address, phys_addr_t phys_addr,
 
 void __iomem * __ioremap(phys_addr_t phys_addr, phys_addr_t size, unsigned long flags)
 {
+	unsigned long offset, pfn, last_pfn;
 	struct vm_struct * area;
-	unsigned long offset;
 	phys_addr_t last_addr;
 	void * addr;
 
@@ -137,18 +152,16 @@ void __iomem * __ioremap(phys_addr_t phys_addr, phys_addr_t size, unsigned long
 		return (void __iomem *) CKSEG1ADDR(phys_addr);
 
 	/*
-	 * Don't allow anybody to remap normal RAM that we're using..
+	 * Don't allow anybody to remap RAM that may be allocated by the page
+	 * allocator, since that could lead to races & data clobbering.
 	 */
-	if (phys_addr < virt_to_phys(high_memory)) {
-		char *t_addr, *t_end;
-		struct page *page;
-
-		t_addr = __va(phys_addr);
-		t_end = t_addr + (size - 1);
-
-		for(page = virt_to_page(t_addr); page <= virt_to_page(t_end); page++)
-			if(!PageReserved(page))
-				return NULL;
+	pfn = PFN_DOWN(phys_addr);
+	last_pfn = PFN_DOWN(last_addr);
+	if (walk_system_ram_range(pfn, last_pfn - pfn + 1, NULL,
+				  __ioremap_check_ram) == 1) {
+		WARN_ONCE(1, "ioremap on RAM at %pa - %pa\n",
+			  &phys_addr, &last_addr);
+		return NULL;
 	}
 
 	/*

arch/openrisc/include/asm/pgalloc.h

@@ -98,8 +98,12 @@ static inline void pte_free(struct mm_struct *mm, struct page *pte)
 	__free_page(pte);
 }
 
+#define __pte_free_tlb(tlb, pte, addr)	\
+do {					\
+	pgtable_page_dtor(pte);		\
+	tlb_remove_page((tlb), (pte));	\
+} while (0)
 
-#define __pte_free_tlb(tlb, pte, addr) tlb_remove_page((tlb), (pte))
 #define pmd_pgtable(pmd) pmd_page(pmd)
 
 #define check_pgt_cache()          do { } while (0)

arch/openrisc/kernel/entry.S

@@ -277,12 +277,6 @@ EXCEPTION_ENTRY(_data_page_fault_handler)
 	l.addi  r3,r1,0                    // pt_regs
 	/* r4 set be EXCEPTION_HANDLE */   // effective address of fault
 
-	/*
-	 * __PHX__: TODO
-	 *
-	 * all this can be written much simpler. look at
-	 * DTLB miss handler in the CONFIG_GUARD_PROTECTED_CORE part
-	 */
 #ifdef CONFIG_OPENRISC_NO_SPR_SR_DSX
 	l.lwz   r6,PT_PC(r3)               // address of an offending insn
 	l.lwz   r6,0(r6)                   // instruction that caused pf
@@ -314,7 +308,7 @@ EXCEPTION_ENTRY(_data_page_fault_handler)
 
 #else
 
-	l.lwz   r6,PT_SR(r3)               // SR
+	l.mfspr r6,r0,SPR_SR               // SR
 	l.andi  r6,r6,SPR_SR_DSX           // check for delay slot exception
 	l.sfne  r6,r0                      // exception happened in delay slot
 	l.bnf   7f

arch/openrisc/kernel/head.S

@@ -210,8 +210,7 @@
  *	 r4  - EEAR     exception EA
  *	 r10 - current	pointing to current_thread_info struct
  *	 r12 - syscall  0, since we didn't come from syscall
- *	 r13 - temp	it actually contains new SR, not needed anymore
- *	 r31 - handler	address of the handler we'll jump to
+ *	 r30 - handler	address of the handler we'll jump to
  *
  *	 handler has to save remaining registers to the exception
  *	 ksp frame *before* tainting them!
@@ -244,6 +243,7 @@
 	/* r1 is KSP, r30 is __pa(KSP) */			;\
 	tophys  (r30,r1)					;\
 	l.sw    PT_GPR12(r30),r12				;\
+	/* r4 use for tmp before EA */				;\
 	l.mfspr r12,r0,SPR_EPCR_BASE				;\
 	l.sw    PT_PC(r30),r12					;\
 	l.mfspr r12,r0,SPR_ESR_BASE				;\
@@ -263,7 +263,10 @@
 	/* r12 == 1 if we come from syscall */			;\
 	CLEAR_GPR(r12)						;\
 	/* ----- turn on MMU ----- */				;\
-	l.ori	r30,r0,(EXCEPTION_SR)				;\
+	/* Carry DSX into exception SR */			;\
+	l.mfspr r30,r0,SPR_SR					;\
+	l.andi	r30,r30,SPR_SR_DSX				;\
+	l.ori	r30,r30,(EXCEPTION_SR)				;\
 	l.mtspr	r0,r30,SPR_ESR_BASE				;\
 	/* r30:	EA address of handler */			;\
 	LOAD_SYMBOL_2_GPR(r30,handler)				;\

arch/openrisc/kernel/traps.c

@@ -300,7 +300,7 @@ static inline int in_delay_slot(struct pt_regs *regs)
 		return 0;
 	}
 #else
-	return regs->sr & SPR_SR_DSX;
+	return mfspr(SPR_SR) & SPR_SR_DSX;
 #endif
 }
 

arch/parisc/Kconfig

@@ -244,11 +244,11 @@ config PARISC_PAGE_SIZE_4KB
 
 config PARISC_PAGE_SIZE_16KB
 	bool "16KB"
-	depends on PA8X00
+	depends on PA8X00 && BROKEN
 
 config PARISC_PAGE_SIZE_64KB
 	bool "64KB"
-	depends on PA8X00
+	depends on PA8X00 && BROKEN
 
 endchoice
 
@@ -347,7 +347,7 @@ config NR_CPUS
 	int "Maximum number of CPUs (2-32)"
 	range 2 32
 	depends on SMP
-	default "32"
+	default "4"
 
 endmenu
 

arch/parisc/Makefile

@@ -65,10 +65,6 @@ endif
 # kernel.
 cflags-y	+= -mdisable-fpregs
 
-# Without this, "ld -r" results in .text sections that are too big
-# (> 0x40000) for branches to reach stubs.
-cflags-y	+= -ffunction-sections
-
 # Use long jumps instead of long branches (needed if your linker fails to
 # link a too big vmlinux executable). Not enabled for building modules.
 ifdef CONFIG_MLONGCALLS

arch/parisc/include/asm/signal.h

@@ -21,14 +21,6 @@ typedef struct {
 	unsigned long sig[_NSIG_WORDS];
 } sigset_t;
 
-#ifndef __KERNEL__
-struct sigaction {
-	__sighandler_t sa_handler;
-	unsigned long sa_flags;
-	sigset_t sa_mask;		/* mask last for extensibility */
-};
-#endif
-
 #include <asm/sigcontext.h>
 
 #endif /* !__ASSEMBLY */

arch/parisc/include/uapi/asm/unistd.h

@@ -364,8 +364,9 @@
 #define __NR_preadv2		(__NR_Linux + 347)
 #define __NR_pwritev2		(__NR_Linux + 348)
 #define __NR_statx		(__NR_Linux + 349)
+#define __NR_io_pgetevents	(__NR_Linux + 350)
 
-#define __NR_Linux_syscalls	(__NR_statx + 1)
+#define __NR_Linux_syscalls	(__NR_io_pgetevents + 1)
 
 
 #define __IGNORE_select		/* newselect */

arch/parisc/kernel/drivers.c

@@ -154,17 +154,14 @@ int register_parisc_driver(struct parisc_driver *driver)
 {
 	/* FIXME: we need this because apparently the sti
 	 * driver can be registered twice */
-	if(driver->drv.name) {
-		printk(KERN_WARNING 
-		       "BUG: skipping previously registered driver %s\n",
-		       driver->name);
+	if (driver->drv.name) {
+		pr_warn("BUG: skipping previously registered driver %s\n",
+			driver->name);
 		return 1;
 	}
 
 	if (!driver->probe) {
-		printk(KERN_WARNING 
-		       "BUG: driver %s has no probe routine\n",
-		       driver->name);
+		pr_warn("BUG: driver %s has no probe routine\n", driver->name);
 		return 1;
 	}
 
@@ -491,12 +488,9 @@ alloc_pa_dev(unsigned long hpa, struct hardware_path *mod_path)
 
 	dev = create_parisc_device(mod_path);
 	if (dev->id.hw_type != HPHW_FAULTY) {
-		printk(KERN_ERR "Two devices have hardware path [%s].  "
-				"IODC data for second device: "
-				"%02x%02x%02x%02x%02x%02x\n"
-				"Rearranging GSC cards sometimes helps\n",
-			parisc_pathname(dev), iodc_data[0], iodc_data[1],
-			iodc_data[3], iodc_data[4], iodc_data[5], iodc_data[6]);
+		pr_err("Two devices have hardware path [%s].  IODC data for second device: %7phN\n"
+		       "Rearranging GSC cards sometimes helps\n",
+			parisc_pathname(dev), iodc_data);
 		return NULL;
 	}
 
@@ -528,8 +522,7 @@ alloc_pa_dev(unsigned long hpa, struct hardware_path *mod_path)
 	 * the keyboard controller
 	 */
 	if ((hpa & 0xfff) == 0 && insert_resource(&iomem_resource, &dev->hpa))
-		printk("Unable to claim HPA %lx for device %s\n",
-				hpa, name);
+		pr_warn("Unable to claim HPA %lx for device %s\n", hpa, name);
 
 	return dev;
 }
@@ -875,7 +868,7 @@ static void print_parisc_device(struct parisc_device *dev)
 	static int count;
 
 	print_pa_hwpath(dev, hw_path);
-	printk(KERN_INFO "%d. %s at 0x%px [%s] { %d, 0x%x, 0x%.3x, 0x%.5x }",
+	pr_info("%d. %s at 0x%px [%s] { %d, 0x%x, 0x%.3x, 0x%.5x }",
 		++count, dev->name, (void*) dev->hpa.start, hw_path, dev->id.hw_type,
 		dev->id.hversion_rev, dev->id.hversion, dev->id.sversion);
 

arch/parisc/kernel/syscall_table.S

@@ -445,6 +445,7 @@
 	ENTRY_COMP(preadv2)
 	ENTRY_COMP(pwritev2)
 	ENTRY_SAME(statx)
+	ENTRY_COMP(io_pgetevents)	/* 350 */
 
 
 .ifne (. - 90b) - (__NR_Linux_syscalls * (91b - 90b))

arch/parisc/kernel/unwind.c

@@ -25,7 +25,7 @@
 
 /* #define DEBUG 1 */
 #ifdef DEBUG
-#define dbg(x...) printk(x)
+#define dbg(x...) pr_debug(x)
 #else
 #define dbg(x...)
 #endif
@@ -182,7 +182,7 @@ int __init unwind_init(void)
 	start = (long)&__start___unwind[0];
 	stop = (long)&__stop___unwind[0];
 
-	printk("unwind_init: start = 0x%lx, end = 0x%lx, entries = %lu\n", 
+	dbg("unwind_init: start = 0x%lx, end = 0x%lx, entries = %lu\n",
 	    start, stop,
 	    (stop - start) / sizeof(struct unwind_table_entry));
 

arch/powerpc/include/asm/book3s/32/pgalloc.h

@@ -138,7 +138,6 @@ static inline void pgtable_free_tlb(struct mmu_gather *tlb,
 static inline void __pte_free_tlb(struct mmu_gather *tlb, pgtable_t table,
 				  unsigned long address)
 {
-	pgtable_page_dtor(table);
 	pgtable_free_tlb(tlb, page_address(table), 0);
 }
 #endif /* _ASM_POWERPC_BOOK3S_32_PGALLOC_H */

arch/powerpc/include/asm/nohash/32/pgalloc.h

@@ -140,7 +140,6 @@ static inline void __pte_free_tlb(struct mmu_gather *tlb, pgtable_t table,
 				  unsigned long address)
 {
 	tlb_flush_pgtable(tlb, address);
-	pgtable_page_dtor(table);
 	pgtable_free_tlb(tlb, page_address(table), 0);
 }
 #endif /* _ASM_POWERPC_PGALLOC_32_H */

arch/powerpc/include/asm/systbl.h

@@ -393,3 +393,4 @@ SYSCALL(pkey_alloc)
 SYSCALL(pkey_free)
 SYSCALL(pkey_mprotect)
 SYSCALL(rseq)
+COMPAT_SYS(io_pgetevents)