Merge branches 'x86/apic', 'x86/asm', 'x86/mm' and 'x86/platform' into x86/core, to merge last updates

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Documentation/ABI/testing/sysfs-devices-system-cpu

@@ -162,7 +162,7 @@ Description:	Discover CPUs in the same CPU frequency coordination domain
 What:		/sys/devices/system/cpu/cpu*/cache/index3/cache_disable_{0,1}
 Date:		August 2008
 KernelVersion:	2.6.27
-Contact:	discuss@x86-64.org
+Contact:	Linux kernel mailing list <linux-kernel@vger.kernel.org>
 Description:	Disable L3 cache indices
 
 		These files exist in every CPU's cache/index3 directory. Each

Documentation/devicetree/bindings/clock/silabs,si5351.txt

@@ -17,7 +17,8 @@ Required properties:
 - #clock-cells: from common clock binding; shall be set to 1.
 - clocks: from common clock binding; list of parent clock
   handles, shall be xtal reference clock or xtal and clkin for
-  si5351c only.
+  si5351c only. Corresponding clock input names are "xtal" and
+  "clkin" respectively.
 - #address-cells: shall be set to 1.
 - #size-cells: shall be set to 0.
 
@@ -71,6 +72,7 @@ i2c-master-node {
 
 		/* connect xtal input to 25MHz reference */
 		clocks = <&ref25>;
+		clock-names = "xtal";
 
 		/* connect xtal input as source of pll0 and pll1 */
 		silabs,pll-source = <0 0>, <1 0>;

Documentation/devicetree/bindings/mtd/m25p80.txt → Documentation/devicetree/bindings/mtd/jedec,spi-nor.txt

@@ -8,8 +8,8 @@ Required properties:
                is not Linux-only, but in case of Linux, see the "m25p_ids"
                table in drivers/mtd/devices/m25p80.c for the list of supported
                chips.
-               Must also include "nor-jedec" for any SPI NOR flash that can be
-               identified by the JEDEC READ ID opcode (0x9F).
+               Must also include "jedec,spi-nor" for any SPI NOR flash that can
+               be identified by the JEDEC READ ID opcode (0x9F).
 - reg : Chip-Select number
 - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
 
@@ -25,7 +25,7 @@ Example:
 	flash: m25p80@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "spansion,m25p80", "nor-jedec";
+		compatible = "spansion,m25p80", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <40000000>;
 		m25p,fast-read;

Documentation/devicetree/bindings/net/cdns-emac.txt

@@ -3,7 +3,8 @@
 Required properties:
 - compatible: Should be "cdns,[<chip>-]{emac}"
   Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC.
-  or the generic form: "cdns,emac".
+  Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC.
+  Or the generic form: "cdns,emac".
 - reg: Address and length of the register set for the device
 - interrupts: Should contain macb interrupt
 - phy-mode: see ethernet.txt file in the same directory.

Documentation/hwmon/tmp401

@@ -20,7 +20,7 @@ Supported chips:
     Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp432.html
   * Texas Instruments TMP435
     Prefix: 'tmp435'
-    Addresses scanned: I2C 0x37, 0x48 - 0x4f
+    Addresses scanned: I2C 0x48 - 0x4f
     Datasheet: http://focus.ti.com/docs/prod/folders/print/tmp435.html
 
 Authors:

Documentation/memory-barriers.txt

@@ -1662,7 +1662,7 @@ CPU from reordering them.
 
 There are some more advanced barrier functions:
 
- (*) set_mb(var, value)
+ (*) smp_store_mb(var, value)
 
      This assigns the value to the variable and then inserts a full memory
      barrier after it, depending on the function.  It isn't guaranteed to
@@ -1975,7 +1975,7 @@ after it has altered the task state:
 	CPU 1
 	===============================
 	set_current_state();
-	  set_mb();
+	  smp_store_mb();
 	    STORE current->state
 	    <general barrier>
 	LOAD event_indicated
@@ -2016,7 +2016,7 @@ between the STORE to indicate the event and the STORE to set TASK_RUNNING:
 	CPU 1				CPU 2
 	===============================	===============================
 	set_current_state();		STORE event_indicated
-	  set_mb();			wake_up();
+	  smp_store_mb();		wake_up();
 	    STORE current->state	  <write barrier>
 	    <general barrier>		  STORE current->state
 	LOAD event_indicated

Documentation/target/tcmu-design.txt

@@ -15,8 +15,7 @@ Contents:
   a) Discovering and configuring TCMU uio devices
   b) Waiting for events on the device(s)
   c) Managing the command ring
-3) Command filtering and pass_level
-4) A final note
+3) A final note
 
 
 TCM Userspace Design
@@ -324,7 +323,7 @@ int handle_device_events(int fd, void *map)
   /* Process events from cmd ring until we catch up with cmd_head */
   while (ent != (void *)mb + mb->cmdr_off + mb->cmd_head) {
 
-    if (tcmu_hdr_get_op(&ent->hdr) == TCMU_OP_CMD) {
+    if (tcmu_hdr_get_op(ent->hdr.len_op) == TCMU_OP_CMD) {
       uint8_t *cdb = (void *)mb + ent->req.cdb_off;
       bool success = true;
 
@@ -339,8 +338,12 @@ int handle_device_events(int fd, void *map)
         ent->rsp.scsi_status = SCSI_CHECK_CONDITION;
       }
     }
+    else if (tcmu_hdr_get_op(ent->hdr.len_op) != TCMU_OP_PAD) {
+      /* Tell the kernel we didn't handle unknown opcodes */
+      ent->hdr.uflags |= TCMU_UFLAG_UNKNOWN_OP;
+    }
     else {
-      /* Do nothing for PAD entries */
+      /* Do nothing for PAD entries except update cmd_tail */
     }
 
     /* update cmd_tail */
@@ -360,28 +363,6 @@ int handle_device_events(int fd, void *map)
 }
 
 
-Command filtering and pass_level
---------------------------------
-
-TCMU supports a "pass_level" option with valid values of 0 or 1.  When
-the value is 0 (the default), nearly all SCSI commands received for
-the device are passed through to the handler. This allows maximum
-flexibility but increases the amount of code required by the handler,
-to support all mandatory SCSI commands. If pass_level is set to 1,
-then only IO-related commands are presented, and the rest are handled
-by LIO's in-kernel command emulation. The commands presented at level
-1 include all versions of:
-
-READ
-WRITE
-WRITE_VERIFY
-XDWRITEREAD
-WRITE_SAME
-COMPARE_AND_WRITE
-SYNCHRONIZE_CACHE
-UNMAP
-
-
 A final note
 ------------
 

Documentation/virtual/kvm/mmu.txt

@@ -169,6 +169,10 @@ Shadow pages contain the following information:
     Contains the value of cr4.smep && !cr0.wp for which the page is valid
     (pages for which this is true are different from other pages; see the
     treatment of cr0.wp=0 below).
+  role.smap_andnot_wp:
+    Contains the value of cr4.smap && !cr0.wp for which the page is valid
+    (pages for which this is true are different from other pages; see the
+    treatment of cr0.wp=0 below).
   gfn:
     Either the guest page table containing the translations shadowed by this
     page, or the base page frame for linear translations.  See role.direct.
@@ -344,10 +348,16 @@ on fault type:
 
 (user write faults generate a #PF)
 
-In the first case there is an additional complication if CR4.SMEP is
-enabled: since we've turned the page into a kernel page, the kernel may now
-execute it.  We handle this by also setting spte.nx.  If we get a user
-fetch or read fault, we'll change spte.u=1 and spte.nx=gpte.nx back.
+In the first case there are two additional complications:
+- if CR4.SMEP is enabled: since we've turned the page into a kernel page,
+  the kernel may now execute it.  We handle this by also setting spte.nx.
+  If we get a user fetch or read fault, we'll change spte.u=1 and
+  spte.nx=gpte.nx back.
+- if CR4.SMAP is disabled: since the page has been changed to a kernel
+  page, it can not be reused when CR4.SMAP is enabled. We set
+  CR4.SMAP && !CR0.WP into shadow page's role to avoid this case. Note,
+  here we do not care the case that CR4.SMAP is enabled since KVM will
+  directly inject #PF to guest due to failed permission check.
 
 To prevent an spte that was converted into a kernel page with cr0.wp=0
 from being written by the kernel after cr0.wp has changed to 1, we make

Documentation/x86/entry_64.txt

@@ -18,10 +18,10 @@ Some of these entries are:
 
  - system_call: syscall instruction from 64-bit code.
 
- - ia32_syscall: int 0x80 from 32-bit or 64-bit code; compat syscall
+ - entry_INT80_compat: int 0x80 from 32-bit or 64-bit code; compat syscall
    either way.
 
- - ia32_syscall, ia32_sysenter: syscall and sysenter from 32-bit
+ - entry_INT80_compat, ia32_sysenter: syscall and sysenter from 32-bit
    code
 
  - interrupt: An array of entries.  Every IDT vector that doesn't

Documentation/x86/mtrr.txt

@@ -1,7 +1,19 @@
 MTRR (Memory Type Range Register) control
-3 Jun 1999
-Richard Gooch
-<rgooch@atnf.csiro.au>
+
+Richard Gooch <rgooch@atnf.csiro.au> - 3 Jun 1999
+Luis R. Rodriguez <mcgrof@do-not-panic.com> - April 9, 2015
+
+===============================================================================
+Phasing out MTRR use
+
+MTRR use is replaced on modern x86 hardware with PAT. Over time the only type
+of effective MTRR that is expected to be supported will be for write-combining.
+As MTRR use is phased out device drivers should use arch_phys_wc_add() to make
+MTRR effective on non-PAT systems while a no-op on PAT enabled systems.
+
+For details refer to Documentation/x86/pat.txt.
+
+===============================================================================
 
   On Intel P6 family processors (Pentium Pro, Pentium II and later)
   the Memory Type Range Registers (MTRRs) may be used to control

Documentation/x86/pat.txt

@@ -12,7 +12,7 @@ virtual addresses.
 
 PAT allows for different types of memory attributes. The most commonly used
 ones that will be supported at this time are Write-back, Uncached,
-Write-combined and Uncached Minus.
+Write-combined, Write-through and Uncached Minus.
 
 
 PAT APIs
@@ -34,16 +34,23 @@ ioremap                |    --    |    UC-     |       UC-        |
                        |          |            |                  |
 ioremap_cache          |    --    |    WB      |       WB         |
                        |          |            |                  |
+ioremap_uc             |    --    |    UC      |       UC         |
+                       |          |            |                  |
 ioremap_nocache        |    --    |    UC-     |       UC-        |
                        |          |            |                  |
 ioremap_wc             |    --    |    --      |       WC         |
                        |          |            |                  |
+ioremap_wt             |    --    |    --      |       WT         |
+                       |          |            |                  |
 set_memory_uc          |    UC-   |    --      |       --         |
  set_memory_wb         |          |            |                  |
                        |          |            |                  |
 set_memory_wc          |    WC    |    --      |       --         |
  set_memory_wb         |          |            |                  |
                        |          |            |                  |
+set_memory_wt          |    WT    |    --      |       --         |
+ set_memory_wb         |          |            |                  |
+                       |          |            |                  |
 pci sysfs resource     |    --    |    --      |       UC-        |
                        |          |            |                  |
 pci sysfs resource_wc  |    --    |    --      |       WC         |
@@ -102,7 +109,38 @@ wants to export a RAM region, it has to do set_memory_uc() or set_memory_wc()
 as step 0 above and also track the usage of those pages and use set_memory_wb()
 before the page is freed to free pool.
 
-
+MTRR effects on PAT / non-PAT systems
+-------------------------------------
+
+The following table provides the effects of using write-combining MTRRs when
+using ioremap*() calls on x86 for both non-PAT and PAT systems. Ideally
+mtrr_add() usage will be phased out in favor of arch_phys_wc_add() which will
+be a no-op on PAT enabled systems. The region over which a arch_phys_wc_add()
+is made, should already have been ioremapped with WC attributes or PAT entries,
+this can be done by using ioremap_wc() / set_memory_wc().  Devices which
+combine areas of IO memory desired to remain uncacheable with areas where
+write-combining is desirable should consider use of ioremap_uc() followed by
+set_memory_wc() to white-list effective write-combined areas.  Such use is
+nevertheless discouraged as the effective memory type is considered
+implementation defined, yet this strategy can be used as last resort on devices
+with size-constrained regions where otherwise MTRR write-combining would
+otherwise not be effective.
+
+----------------------------------------------------------------------
+MTRR Non-PAT   PAT    Linux ioremap value        Effective memory type
+----------------------------------------------------------------------
+                                                  Non-PAT |  PAT
+     PAT
+     |PCD
+     ||PWT
+     |||
+WC   000      WB      _PAGE_CACHE_MODE_WB            WC   |   WC
+WC   001      WC      _PAGE_CACHE_MODE_WC            WC*  |   WC
+WC   010      UC-     _PAGE_CACHE_MODE_UC_MINUS      WC*  |   UC
+WC   011      UC      _PAGE_CACHE_MODE_UC            UC   |   UC
+----------------------------------------------------------------------
+
+(*) denotes implementation defined and is discouraged
 
 Notes:
 
@@ -115,8 +153,8 @@ can be more restrictive, in case of any existing aliasing for that address.
 For example: If there is an existing uncached mapping, a new ioremap_wc can
 return uncached mapping in place of write-combine requested.
 
-set_memory_[uc|wc] and set_memory_wb should be used in pairs, where driver will
-first make a region uc or wc and switch it back to wb after use.
+set_memory_[uc|wc|wt] and set_memory_wb should be used in pairs, where driver
+will first make a region uc, wc or wt and switch it back to wb after use.
 
 Over time writes to /proc/mtrr will be deprecated in favor of using PAT based
 interfaces. Users writing to /proc/mtrr are suggested to use above interfaces.
@@ -124,7 +162,7 @@ interfaces. Users writing to /proc/mtrr are suggested to use above interfaces.
 Drivers should use ioremap_[uc|wc] to access PCI BARs with [uc|wc] access
 types.
 
-Drivers should use set_memory_[uc|wc] to set access type for RAM ranges.
+Drivers should use set_memory_[uc|wc|wt] to set access type for RAM ranges.
 
 
 PAT debugging

Documentation/x86/x86_64/boot-options.txt

@@ -31,6 +31,9 @@ Machine check
 		(e.g. BIOS or hardware monitoring applications), conflicting
 		with OS's error handling, and you cannot deactivate the agent,
 		then this option will be a help.
+   mce=no_lmce
+		Do not opt-in to Local MCE delivery. Use legacy method
+		to broadcast MCEs.
    mce=bootlog
 		Enable logging of machine checks left over from booting.
 		Disabled by default on AMD because some BIOS leave bogus ones.

MAINTAINERS

@@ -2427,7 +2427,6 @@ L:	linux-security-module@vger.kernel.org
 S:	Supported
 F:	include/linux/capability.h
 F:	include/uapi/linux/capability.h
-F:	security/capability.c
 F:	security/commoncap.c
 F:	kernel/capability.c
 
@@ -3825,10 +3824,11 @@ M:	David Woodhouse <dwmw2@infradead.org>
 L:	linux-embedded@vger.kernel.org
 S:	Maintained
 
-EMULEX LPFC FC SCSI DRIVER
-M:	James Smart <james.smart@emulex.com>
+EMULEX/AVAGO LPFC FC/FCOE SCSI DRIVER
+M:	James Smart <james.smart@avagotech.com>
+M:	Dick Kennedy <dick.kennedy@avagotech.com>
 L:	linux-scsi@vger.kernel.org
-W:	http://sourceforge.net/projects/lpfcxxxx
+W:	http://www.avagotech.com
 S:	Supported
 F:	drivers/scsi/lpfc/
 
@@ -4536,7 +4536,7 @@ M:	Jean Delvare <jdelvare@suse.de>
 M:	Guenter Roeck <linux@roeck-us.net>
 L:	lm-sensors@lm-sensors.org
 W:	http://www.lm-sensors.org/
-T:	quilt kernel.org/pub/linux/kernel/people/jdelvare/linux-2.6/jdelvare-hwmon/
+T:	quilt http://jdelvare.nerim.net/devel/linux/jdelvare-hwmon/
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging.git
 S:	Maintained
 F:	Documentation/hwmon/
@@ -8829,9 +8829,11 @@ F:	drivers/misc/phantom.c
 F:	include/uapi/linux/phantom.h
 
 SERVER ENGINES 10Gbps iSCSI - BladeEngine 2 DRIVER
-M:	Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
+M:	Jayamohan Kallickal <jayamohan.kallickal@avagotech.com>
+M:	Minh Tran <minh.tran@avagotech.com>
+M:	John Soni Jose <sony.john-n@avagotech.com>
 L:	linux-scsi@vger.kernel.org
-W:	http://www.emulex.com
+W:	http://www.avagotech.com
 S:	Supported
 F:	drivers/scsi/be2iscsi/
 
@@ -10585,8 +10587,7 @@ F:	drivers/virtio/virtio_input.c
 F:	include/uapi/linux/virtio_input.h
 
 VIA RHINE NETWORK DRIVER
-M:	Roger Luethi <rl@hellgate.ch>
-S:	Maintained
+S:	Orphan
 F:	drivers/net/ethernet/via/via-rhine.c
 
 VIA SD/MMC CARD CONTROLLER DRIVER
@@ -10892,7 +10893,7 @@ M:	Andy Lutomirski <luto@amacapital.net>
 L:	linux-kernel@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git x86/vdso
 S:	Maintained
-F:	arch/x86/vdso/
+F:	arch/x86/entry/vdso/
 
 XC2028/3028 TUNER DRIVER
 M:	Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Makefile

@@ -1,7 +1,7 @@
 VERSION = 4
 PATCHLEVEL = 1
 SUBLEVEL = 0
-EXTRAVERSION = -rc3
+EXTRAVERSION = -rc6
 NAME = Hurr durr I'ma sheep
 
 # *DOCUMENTATION*

arch/alpha/boot/Makefile

@@ -14,6 +14,9 @@ targets		:= vmlinux.gz vmlinux \
 		   tools/bootpzh bootloader bootpheader bootpzheader 
 OBJSTRIP	:= $(obj)/tools/objstrip
 
+HOSTCFLAGS	:= -Wall -I$(objtree)/usr/include
+BOOTCFLAGS	+= -I$(obj) -I$(srctree)/$(obj)
+
 # SRM bootable image.  Copy to offset 512 of a partition.
 $(obj)/bootimage: $(addprefix $(obj)/tools/,mkbb lxboot bootlx) $(obj)/vmlinux.nh
 	( cat $(obj)/tools/lxboot $(obj)/tools/bootlx $(obj)/vmlinux.nh ) > $@ 
@@ -96,13 +99,14 @@ $(obj)/tools/bootph: $(obj)/bootpheader $(OBJSTRIP) FORCE
 $(obj)/tools/bootpzh: $(obj)/bootpzheader $(OBJSTRIP) FORCE
 	$(call if_changed,objstrip)
 
-LDFLAGS_bootloader   := -static -uvsprintf -T  #-N -relax
-LDFLAGS_bootpheader  := -static -uvsprintf -T  #-N -relax
-LDFLAGS_bootpzheader := -static -uvsprintf -T  #-N -relax
+LDFLAGS_bootloader   := -static -T # -N -relax
+LDFLAGS_bootloader   := -static -T # -N -relax
+LDFLAGS_bootpheader  := -static -T # -N -relax
+LDFLAGS_bootpzheader := -static -T # -N -relax
 
-OBJ_bootlx   := $(obj)/head.o $(obj)/main.o
-OBJ_bootph   := $(obj)/head.o $(obj)/bootp.o
-OBJ_bootpzh  := $(obj)/head.o $(obj)/bootpz.o $(obj)/misc.o
+OBJ_bootlx   := $(obj)/head.o $(obj)/stdio.o $(obj)/main.o
+OBJ_bootph   := $(obj)/head.o $(obj)/stdio.o $(obj)/bootp.o
+OBJ_bootpzh  := $(obj)/head.o $(obj)/stdio.o $(obj)/bootpz.o $(obj)/misc.o
 
 $(obj)/bootloader: $(obj)/bootloader.lds $(OBJ_bootlx) $(LIBS_Y) FORCE
 	$(call if_changed,ld)

arch/alpha/boot/main.c

@@ -19,7 +19,6 @@
 
 #include "ksize.h"
 
-extern int vsprintf(char *, const char *, va_list);
 extern unsigned long switch_to_osf_pal(unsigned long nr,
 	struct pcb_struct * pcb_va, struct pcb_struct * pcb_pa,
 	unsigned long *vptb);

arch/alpha/boot/stdio.c

@@ -0,0 +1,306 @@
+/*
+ * Copyright (C) Paul Mackerras 1997.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+#include <stdarg.h>
+#include <stddef.h>
+
+size_t strnlen(const char * s, size_t count)
+{
+	const char *sc;
+
+	for (sc = s; count-- && *sc != '\0'; ++sc)
+		/* nothing */;
+	return sc - s;
+}
+
+# define do_div(n, base) ({						\
+	unsigned int __base = (base);					\
+	unsigned int __rem;						\
+	__rem = ((unsigned long long)(n)) % __base;			\
+	(n) = ((unsigned long long)(n)) / __base;			\
+	__rem;								\
+})
+
+
+static int skip_atoi(const char **s)
+{
+	int i, c;
+
+	for (i = 0; '0' <= (c = **s) && c <= '9'; ++*s)
+		i = i*10 + c - '0';
+	return i;
+}
+
+#define ZEROPAD	1		/* pad with zero */
+#define SIGN	2		/* unsigned/signed long */
+#define PLUS	4		/* show plus */
+#define SPACE	8		/* space if plus */
+#define LEFT	16		/* left justified */
+#define SPECIAL	32		/* 0x */
+#define LARGE	64		/* use 'ABCDEF' instead of 'abcdef' */
+
+static char * number(char * str, unsigned long long num, int base, int size, int precision, int type)
+{
+	char c,sign,tmp[66];
+	const char *digits="0123456789abcdefghijklmnopqrstuvwxyz";
+	int i;
+
+	if (type & LARGE)
+		digits = "0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ";
+	if (type & LEFT)
+		type &= ~ZEROPAD;
+	if (base < 2 || base > 36)
+		return 0;
+	c = (type & ZEROPAD) ? '0' : ' ';
+	sign = 0;
+	if (type & SIGN) {
+		if ((signed long long)num < 0) {
+			sign = '-';
+			num = - (signed long long)num;
+			size--;
+		} else if (type & PLUS) {
+			sign = '+';
+			size--;
+		} else if (type & SPACE) {
+			sign = ' ';
+			size--;
+		}
+	}
+	if (type & SPECIAL) {
+		if (base == 16)
+			size -= 2;
+		else if (base == 8)
+			size--;
+	}
+	i = 0;
+	if (num == 0)
+		tmp[i++]='0';
+	else while (num != 0) {
+		tmp[i++] = digits[do_div(num, base)];
+	}
+	if (i > precision)
+		precision = i;
+	size -= precision;
+	if (!(type&(ZEROPAD+LEFT)))
+		while(size-->0)
+			*str++ = ' ';
+	if (sign)
+		*str++ = sign;
+	if (type & SPECIAL) {
+		if (base==8)
+			*str++ = '0';
+		else if (base==16) {
+			*str++ = '0';
+			*str++ = digits[33];
+		}
+	}
+	if (!(type & LEFT))
+		while (size-- > 0)
+			*str++ = c;
+	while (i < precision--)
+		*str++ = '0';
+	while (i-- > 0)
+		*str++ = tmp[i];
+	while (size-- > 0)
+		*str++ = ' ';
+	return str;
+}
+
+int vsprintf(char *buf, const char *fmt, va_list args)
+{
+	int len;
+	unsigned long long num;
+	int i, base;
+	char * str;
+	const char *s;
+
+	int flags;		/* flags to number() */
+
+	int field_width;	/* width of output field */
+	int precision;		/* min. # of digits for integers; max
+				   number of chars for from string */
+	int qualifier;		/* 'h', 'l', or 'L' for integer fields */
+	                        /* 'z' support added 23/7/1999 S.H.    */
+				/* 'z' changed to 'Z' --davidm 1/25/99 */
+
+
+	for (str=buf ; *fmt ; ++fmt) {
+		if (*fmt != '%') {
+			*str++ = *fmt;
+			continue;
+		}
+
+		/* process flags */
+		flags = 0;
+		repeat:
+			++fmt;		/* this also skips first '%' */
+			switch (*fmt) {
+				case '-': flags |= LEFT; goto repeat;
+				case '+': flags |= PLUS; goto repeat;
+				case ' ': flags |= SPACE; goto repeat;
+				case '#': flags |= SPECIAL; goto repeat;
+				case '0': flags |= ZEROPAD; goto repeat;
+				}
+
+		/* get field width */
+		field_width = -1;
+		if ('0' <= *fmt && *fmt <= '9')
+			field_width = skip_atoi(&fmt);
+		else if (*fmt == '*') {
+			++fmt;
+			/* it's the next argument */
+			field_width = va_arg(args, int);
+			if (field_width < 0) {
+				field_width = -field_width;
+				flags |= LEFT;
+			}
+		}
+
+		/* get the precision */
+		precision = -1;
+		if (*fmt == '.') {
+			++fmt;
+			if ('0' <= *fmt && *fmt <= '9')
+				precision = skip_atoi(&fmt);
+			else if (*fmt == '*') {
+				++fmt;
+				/* it's the next argument */
+				precision = va_arg(args, int);
+			}
+			if (precision < 0)
+				precision = 0;
+		}
+
+		/* get the conversion qualifier */
+		qualifier = -1;
+		if (*fmt == 'l' && *(fmt + 1) == 'l') {
+			qualifier = 'q';
+			fmt += 2;
+		} else if (*fmt == 'h' || *fmt == 'l' || *fmt == 'L'
+			|| *fmt == 'Z') {
+			qualifier = *fmt;
+			++fmt;
+		}
+
+		/* default base */
+		base = 10;
+
+		switch (*fmt) {
+		case 'c':
+			if (!(flags & LEFT))
+				while (--field_width > 0)
+					*str++ = ' ';
+			*str++ = (unsigned char) va_arg(args, int);
+			while (--field_width > 0)
+				*str++ = ' ';
+			continue;
+
+		case 's':
+			s = va_arg(args, char *);
+			if (!s)
+				s = "<NULL>";
+
+			len = strnlen(s, precision);
+
+			if (!(flags & LEFT))
+				while (len < field_width--)
+					*str++ = ' ';
+			for (i = 0; i < len; ++i)
+				*str++ = *s++;
+			while (len < field_width--)
+				*str++ = ' ';
+			continue;
+
+		case 'p':
+			if (field_width == -1) {
+				field_width = 2*sizeof(void *);
+				flags |= ZEROPAD;
+			}
+			str = number(str,
+				(unsigned long) va_arg(args, void *), 16,
+				field_width, precision, flags);
+			continue;
+
+
+		case 'n':
+			if (qualifier == 'l') {
+				long * ip = va_arg(args, long *);
+				*ip = (str - buf);
+			} else if (qualifier == 'Z') {
+				size_t * ip = va_arg(args, size_t *);
+				*ip = (str - buf);
+			} else {
+				int * ip = va_arg(args, int *);
+				*ip = (str - buf);
+			}
+			continue;
+
+		case '%':
+			*str++ = '%';
+			continue;
+
+		/* integer number formats - set up the flags and "break" */
+		case 'o':
+			base = 8;
+			break;
+
+		case 'X':
+			flags |= LARGE;
+		case 'x':
+			base = 16;
+			break;
+
+		case 'd':
+		case 'i':
+			flags |= SIGN;
+		case 'u':
+			break;
+
+		default:
+			*str++ = '%';
+			if (*fmt)
+				*str++ = *fmt;
+			else
+				--fmt;
+			continue;
+		}
+		if (qualifier == 'l') {
+			num = va_arg(args, unsigned long);
+			if (flags & SIGN)
+				num = (signed long) num;
+		} else if (qualifier == 'q') {
+			num = va_arg(args, unsigned long long);
+			if (flags & SIGN)
+				num = (signed long long) num;
+		} else if (qualifier == 'Z') {
+			num = va_arg(args, size_t);
+		} else if (qualifier == 'h') {
+			num = (unsigned short) va_arg(args, int);
+			if (flags & SIGN)
+				num = (signed short) num;
+		} else {
+			num = va_arg(args, unsigned int);
+			if (flags & SIGN)
+				num = (signed int) num;
+		}
+		str = number(str, num, base, field_width, precision, flags);
+	}
+	*str = '\0';
+	return str-buf;
+}
+
+int sprintf(char * buf, const char *fmt, ...)
+{
+	va_list args;
+	int i;
+
+	va_start(args, fmt);
+	i=vsprintf(buf,fmt,args);
+	va_end(args);
+	return i;
+}

arch/alpha/boot/tools/objstrip.c

@@ -27,6 +27,9 @@
 #include <linux/param.h>
 #ifdef __ELF__
 # include <linux/elf.h>
+# define elfhdr elf64_hdr
+# define elf_phdr elf64_phdr
+# define elf_check_arch(x) ((x)->e_machine == EM_ALPHA)
 #endif
 
 /* bootfile size must be multiple of BLOCK_SIZE: */

arch/alpha/include/asm/cmpxchg.h

@@ -66,6 +66,4 @@
 #undef __ASM__MB
 #undef ____cmpxchg
 
-#define __HAVE_ARCH_CMPXCHG 1
-
 #endif /* _ALPHA_CMPXCHG_H */

arch/alpha/include/asm/types.h

@@ -2,6 +2,5 @@
 #define _ALPHA_TYPES_H
 
 #include <asm-generic/int-ll64.h>
-#include <uapi/asm/types.h>
 
 #endif /* _ALPHA_TYPES_H */

arch/alpha/include/asm/unistd.h

@@ -3,7 +3,7 @@
 
 #include <uapi/asm/unistd.h>
 
-#define NR_SYSCALLS			511
+#define NR_SYSCALLS			514
 
 #define __ARCH_WANT_OLD_READDIR
 #define __ARCH_WANT_STAT64

arch/alpha/include/uapi/asm/unistd.h

@@ -472,5 +472,8 @@
 #define __NR_sched_setattr		508
 #define __NR_sched_getattr		509
 #define __NR_renameat2			510
+#define __NR_getrandom			511
+#define __NR_memfd_create		512
+#define __NR_execveat			513
 
 #endif /* _UAPI_ALPHA_UNISTD_H */

arch/alpha/kernel/err_ev6.c

@@ -6,7 +6,6 @@
  *	Error handling code supporting Alpha systems
  */
 
-#include <linux/init.h>
 #include <linux/sched.h>
 
 #include <asm/io.h>

arch/alpha/kernel/irq.c

@@ -19,7 +19,6 @@
 #include <linux/ptrace.h>
 #include <linux/interrupt.h>
 #include <linux/random.h>
-#include <linux/init.h>
 #include <linux/irq.h>
 #include <linux/proc_fs.h>
 #include <linux/seq_file.h>

arch/alpha/kernel/osf_sys.c

@@ -1019,14 +1019,13 @@ SYSCALL_DEFINE2(osf_settimeofday, struct timeval32 __user *, tv,
  	if (tv) {
 		if (get_tv32((struct timeval *)&kts, tv))
 			return -EFAULT;
+		kts.tv_nsec *= 1000;
 	}
 	if (tz) {
 		if (copy_from_user(&ktz, tz, sizeof(*tz)))
 			return -EFAULT;
 	}
 
-	kts.tv_nsec *= 1000;
-
 	return do_sys_settimeofday(tv ? &kts : NULL, tz ? &ktz : NULL);
 }
 

arch/alpha/kernel/process.c

@@ -236,12 +236,11 @@ release_thread(struct task_struct *dead_task)
 }
 
 /*
- * Copy an alpha thread..
+ * Copy architecture-specific thread state
  */
-
 int
 copy_thread(unsigned long clone_flags, unsigned long usp,
-	    unsigned long arg,
+	    unsigned long kthread_arg,
 	    struct task_struct *p)
 {
 	extern void ret_from_fork(void);
@@ -262,7 +261,7 @@ copy_thread(unsigned long clone_flags, unsigned long usp,
 			sizeof(struct switch_stack) + sizeof(struct pt_regs));
 		childstack->r26 = (unsigned long) ret_from_kernel_thread;
 		childstack->r9 = usp;	/* function */
-		childstack->r10 = arg;
+		childstack->r10 = kthread_arg;
 		childregs->hae = alpha_mv.hae_cache,
 		childti->pcb.usp = 0;
 		return 0;

arch/alpha/kernel/smp.c

@@ -63,7 +63,6 @@ static struct {
 enum ipi_message_type {
 	IPI_RESCHEDULE,
 	IPI_CALL_FUNC,
-	IPI_CALL_FUNC_SINGLE,
 	IPI_CPU_STOP,
 };
 
@@ -506,7 +505,6 @@ setup_profiling_timer(unsigned int multiplier)
 	return -EINVAL;
 }
 
-
 static void
 send_ipi_message(const struct cpumask *to_whom, enum ipi_message_type operation)
 {
@@ -552,10 +550,6 @@ handle_ipi(struct pt_regs *regs)
 			generic_smp_call_function_interrupt();
 			break;
 
-		case IPI_CALL_FUNC_SINGLE:
-			generic_smp_call_function_single_interrupt();
-			break;
-
 		case IPI_CPU_STOP:
 			halt();
 
@@ -606,7 +600,7 @@ void arch_send_call_function_ipi_mask(const struct cpumask *mask)
 
 void arch_send_call_function_single_ipi(int cpu)
 {
-	send_ipi_message(cpumask_of(cpu), IPI_CALL_FUNC_SINGLE);
+	send_ipi_message(cpumask_of(cpu), IPI_CALL_FUNC);
 }
 
 static void

arch/alpha/kernel/srmcons.c

@@ -237,8 +237,7 @@ srmcons_init(void)
 
 	return -ENODEV;
 }
-
-module_init(srmcons_init);
+device_initcall(srmcons_init);
 
 
 /*

arch/alpha/kernel/sys_marvel.c

@@ -331,7 +331,7 @@ marvel_map_irq(const struct pci_dev *cdev, u8 slot, u8 pin)
 	pci_read_config_byte(dev, PCI_INTERRUPT_LINE, &intline);
 	irq = intline;
 
-	msi_loc = pci_find_capability(dev, PCI_CAP_ID_MSI);
+	msi_loc = dev->msi_cap;
 	msg_ctl = 0;
 	if (msi_loc) 
 		pci_read_config_word(dev, msi_loc + PCI_MSI_FLAGS, &msg_ctl);

arch/alpha/kernel/systbls.S

@@ -529,6 +529,9 @@ sys_call_table:
 	.quad sys_sched_setattr
 	.quad sys_sched_getattr
 	.quad sys_renameat2			/* 510 */
+	.quad sys_getrandom
+	.quad sys_memfd_create
+	.quad sys_execveat
 
 	.size sys_call_table, . - sys_call_table
 	.type sys_call_table, @object

arch/alpha/kernel/traps.c

@@ -14,7 +14,6 @@
 #include <linux/tty.h>
 #include <linux/delay.h>
 #include <linux/module.h>
-#include <linux/init.h>
 #include <linux/kallsyms.h>
 #include <linux/ratelimit.h>
 

arch/alpha/oprofile/op_model_ev4.c

@@ -8,7 +8,6 @@
  */
 
 #include <linux/oprofile.h>
-#include <linux/init.h>
 #include <linux/smp.h>
 #include <asm/ptrace.h>
 

arch/alpha/oprofile/op_model_ev5.c

@@ -8,7 +8,6 @@
  */
 
 #include <linux/oprofile.h>
-#include <linux/init.h>
 #include <linux/smp.h>
 #include <asm/ptrace.h>
 

arch/alpha/oprofile/op_model_ev6.c

@@ -8,7 +8,6 @@
  */
 
 #include <linux/oprofile.h>
-#include <linux/init.h>
 #include <linux/smp.h>
 #include <asm/ptrace.h>
 

arch/alpha/oprofile/op_model_ev67.c

@@ -9,7 +9,6 @@
  */
 
 #include <linux/oprofile.h>
-#include <linux/init.h>
 #include <linux/smp.h>
 #include <asm/ptrace.h>
 

arch/arc/include/asm/io.h

@@ -20,6 +20,7 @@ extern void iounmap(const void __iomem *addr);
 
 #define ioremap_nocache(phy, sz)	ioremap(phy, sz)
 #define ioremap_wc(phy, sz)		ioremap(phy, sz)
+#define ioremap_wt(phy, sz)		ioremap(phy, sz)
 
 /* Change struct page to physical address */
 #define page_to_phys(page)		(page_to_pfn(page) << PAGE_SHIFT)

arch/arm/boot/dts/Makefile

@@ -223,7 +223,7 @@ dtb-$(CONFIG_SOC_IMX25) += \
 	imx25-eukrea-mbimxsd25-baseboard-dvi-vga.dtb \
 	imx25-karo-tx25.dtb \
 	imx25-pdk.dtb
-dtb-$(CONFIG_SOC_IMX31) += \
+dtb-$(CONFIG_SOC_IMX27) += \
 	imx27-apf27.dtb \
 	imx27-apf27dev.dtb \
 	imx27-eukrea-mbimxsd27-baseboard.dtb \

arch/arm/boot/dts/am335x-boneblack.dts

@@ -80,7 +80,3 @@
 		status = "okay";
 	};
 };
-
-&rtc {
-	system-power-controller;
-};

arch/arm/boot/dts/am335x-evmsk.dts

@@ -654,7 +654,7 @@
 	wlcore: wlcore@2 {
 		compatible = "ti,wl1271";
 		reg = <2>;
-		interrupt-parent = <&gpio1>;
+		interrupt-parent = <&gpio0>;
 		interrupts = <31 IRQ_TYPE_LEVEL_HIGH>; /* gpio 31 */
 		ref-clock-frequency = <38400000>;
 	};

arch/arm/boot/dts/exynos4412-trats2.dts

@@ -736,7 +736,7 @@
 
 			display-timings {
 				timing-0 {
-					clock-frequency = <0>;
+					clock-frequency = <57153600>;
 					hactive = <720>;
 					vactive = <1280>;
 					hfront-porch = <5>;

arch/arm/boot/dts/imx27.dtsi

@@ -533,7 +533,7 @@
 
 			fec: ethernet@1002b000 {
 				compatible = "fsl,imx27-fec";
-				reg = <0x1002b000 0x4000>;
+				reg = <0x1002b000 0x1000>;
 				interrupts = <50>;
 				clocks = <&clks IMX27_CLK_FEC_IPG_GATE>,
 					 <&clks IMX27_CLK_FEC_AHB_GATE>;

arch/arm/boot/dts/omap3-devkit8000.dts

@@ -110,6 +110,8 @@
 	nand@0,0 {
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
 		nand-bus-width = <16>;
+		gpmc,device-width = <2>;
+		ti,nand-ecc-opt = "sw";
 
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;

arch/arm/boot/dts/zynq-7000.dtsi

@@ -193,7 +193,7 @@
 		};
 
 		gem0: ethernet@e000b000 {
-			compatible = "cdns,gem";
+			compatible = "cdns,zynq-gem";
 			reg = <0xe000b000 0x1000>;
 			status = "disabled";
 			interrupts = <0 22 4>;
@@ -204,7 +204,7 @@
 		};
 
 		gem1: ethernet@e000c000 {
-			compatible = "cdns,gem";
+			compatible = "cdns,zynq-gem";
 			reg = <0xe000c000 0x1000>;
 			status = "disabled";
 			interrupts = <0 45 4>;

arch/arm/configs/multi_v7_defconfig

@@ -429,7 +429,7 @@ CONFIG_USB_EHCI_EXYNOS=y
 CONFIG_USB_EHCI_TEGRA=y
 CONFIG_USB_EHCI_HCD_STI=y
 CONFIG_USB_EHCI_HCD_PLATFORM=y
-CONFIG_USB_ISP1760_HCD=y
+CONFIG_USB_ISP1760=y
 CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_OHCI_HCD_STI=y
 CONFIG_USB_OHCI_HCD_PLATFORM=y

arch/arm/include/asm/barrier.h

@@ -81,7 +81,7 @@ do {									\
 #define read_barrier_depends()		do { } while(0)
 #define smp_read_barrier_depends()	do { } while(0)
 
-#define set_mb(var, value)	do { var = value; smp_mb(); } while (0)
+#define smp_store_mb(var, value)	do { WRITE_ONCE(var, value); smp_mb(); } while (0)
 
 #define smp_mb__before_atomic()	smp_mb()
 #define smp_mb__after_atomic()	smp_mb()

arch/arm/include/asm/io.h

@@ -336,6 +336,7 @@ extern void _memset_io(volatile void __iomem *, int, size_t);
 #define ioremap_nocache(cookie,size)	__arm_ioremap((cookie), (size), MT_DEVICE)
 #define ioremap_cache(cookie,size)	__arm_ioremap((cookie), (size), MT_DEVICE_CACHED)
 #define ioremap_wc(cookie,size)		__arm_ioremap((cookie), (size), MT_DEVICE_WC)
+#define ioremap_wt(cookie,size)		__arm_ioremap((cookie), (size), MT_DEVICE)
 #define iounmap				__arm_iounmap
 
 /*

arch/arm/kernel/entry-common.S

@@ -33,7 +33,9 @@ ret_fast_syscall:
  UNWIND(.fnstart	)
  UNWIND(.cantunwind	)
 	disable_irq				@ disable interrupts
-	ldr	r1, [tsk, #TI_FLAGS]
+	ldr	r1, [tsk, #TI_FLAGS]		@ re-check for syscall tracing
+	tst	r1, #_TIF_SYSCALL_WORK
+	bne	__sys_trace_return
 	tst	r1, #_TIF_WORK_MASK
 	bne	fast_work_pending
 	asm_trace_hardirqs_on

arch/arm/kernel/perf_event_cpu.c

@@ -304,16 +304,17 @@ static int probe_current_pmu(struct arm_pmu *pmu)
 static int of_pmu_irq_cfg(struct platform_device *pdev)
 {
 	int i, irq;
-	int *irqs = kcalloc(pdev->num_resources, sizeof(*irqs), GFP_KERNEL);
-
-	if (!irqs)
-		return -ENOMEM;
+	int *irqs;
 
 	/* Don't bother with PPIs; they're already affine */
 	irq = platform_get_irq(pdev, 0);
 	if (irq >= 0 && irq_is_percpu(irq))
 		return 0;
 
+	irqs = kcalloc(pdev->num_resources, sizeof(*irqs), GFP_KERNEL);
+	if (!irqs)
+		return -ENOMEM;
+
 	for (i = 0; i < pdev->num_resources; ++i) {
 		struct device_node *dn;
 		int cpu;

arch/arm/mach-imx/gpc.c

@@ -280,9 +280,15 @@ void __init imx_gpc_check_dt(void)
 	struct device_node *np;
 
 	np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-gpc");
-	if (WARN_ON(!np ||
-		    !of_find_property(np, "interrupt-controller", NULL)))
-		pr_warn("Outdated DT detected, system is about to crash!!!\n");
+	if (WARN_ON(!np))
+		return;
+
+	if (WARN_ON(!of_find_property(np, "interrupt-controller", NULL))) {
+		pr_warn("Outdated DT detected, suspend/resume will NOT work\n");
+
+		/* map GPC, so that at least CPUidle and WARs keep working */
+		gpc_base = of_iomap(np, 0);
+	}
 }
 
 #ifdef CONFIG_PM_GENERIC_DOMAINS
@@ -443,6 +449,10 @@ static int imx_gpc_probe(struct platform_device *pdev)
 	struct regulator *pu_reg;
 	int ret;
 
+	/* bail out if DT too old and doesn't provide the necessary info */
+	if (!of_property_read_bool(pdev->dev.of_node, "#power-domain-cells"))
+		return 0;
+
 	pu_reg = devm_regulator_get_optional(&pdev->dev, "pu");
 	if (PTR_ERR(pu_reg) == -ENODEV)
 		pu_reg = NULL;

arch/arm/mach-pxa/pxa_cplds_irqs.c

@@ -107,7 +107,7 @@ static int cplds_probe(struct platform_device *pdev)
 	struct resource *res;
 	struct cplds *fpga;
 	int ret;
-	unsigned int base_irq = 0;
+	int base_irq;
 	unsigned long irqflags = 0;
 
 	fpga = devm_kzalloc(&pdev->dev, sizeof(*fpga), GFP_KERNEL);

arch/arm/mm/mmu.c

@@ -1112,22 +1112,22 @@ void __init sanity_check_meminfo(void)
 			}
 
 			/*
-			 * Find the first non-section-aligned page, and point
+			 * Find the first non-pmd-aligned page, and point
 			 * memblock_limit at it. This relies on rounding the
-			 * limit down to be section-aligned, which happens at
-			 * the end of this function.
+			 * limit down to be pmd-aligned, which happens at the
+			 * end of this function.
 			 *
 			 * With this algorithm, the start or end of almost any
-			 * bank can be non-section-aligned. The only exception
-			 * is that the start of the bank 0 must be section-
+			 * bank can be non-pmd-aligned. The only exception is
+			 * that the start of the bank 0 must be section-
 			 * aligned, since otherwise memory would need to be
 			 * allocated when mapping the start of bank 0, which
 			 * occurs before any free memory is mapped.
 			 */
 			if (!memblock_limit) {
-				if (!IS_ALIGNED(block_start, SECTION_SIZE))
+				if (!IS_ALIGNED(block_start, PMD_SIZE))
 					memblock_limit = block_start;
-				else if (!IS_ALIGNED(block_end, SECTION_SIZE))
+				else if (!IS_ALIGNED(block_end, PMD_SIZE))
 					memblock_limit = arm_lowmem_limit;
 			}
 
@@ -1137,12 +1137,12 @@ void __init sanity_check_meminfo(void)
 	high_memory = __va(arm_lowmem_limit - 1) + 1;
 
 	/*
-	 * Round the memblock limit down to a section size.  This
+	 * Round the memblock limit down to a pmd size.  This
 	 * helps to ensure that we will allocate memory from the
-	 * last full section, which should be mapped.
+	 * last full pmd, which should be mapped.
 	 */
 	if (memblock_limit)
-		memblock_limit = round_down(memblock_limit, SECTION_SIZE);
+		memblock_limit = round_down(memblock_limit, PMD_SIZE);
 	if (!memblock_limit)
 		memblock_limit = arm_lowmem_limit;
 

arch/arm/xen/enlighten.c

@@ -272,6 +272,7 @@ void xen_arch_pre_suspend(void) { }
 void xen_arch_post_suspend(int suspend_cancelled) { }
 void xen_timer_resume(void) { }
 void xen_arch_resume(void) { }
+void xen_arch_suspend(void) { }
 
 
 /* In the hypervisor.S file. */

arch/arm64/include/asm/barrier.h

@@ -114,7 +114,7 @@ do {									\
 #define read_barrier_depends()		do { } while(0)
 #define smp_read_barrier_depends()	do { } while(0)
 
-#define set_mb(var, value)	do { var = value; smp_mb(); } while (0)
+#define smp_store_mb(var, value)	do { WRITE_ONCE(var, value); smp_mb(); } while (0)
 #define nop()		asm volatile("nop");
 
 #define smp_mb__before_atomic()	smp_mb()

arch/arm64/include/asm/io.h

@@ -170,6 +170,7 @@ extern void __iomem *ioremap_cache(phys_addr_t phys_addr, size_t size);
 #define ioremap(addr, size)		__ioremap((addr), (size), __pgprot(PROT_DEVICE_nGnRE))
 #define ioremap_nocache(addr, size)	__ioremap((addr), (size), __pgprot(PROT_DEVICE_nGnRE))
 #define ioremap_wc(addr, size)		__ioremap((addr), (size), __pgprot(PROT_NORMAL_NC))
+#define ioremap_wt(addr, size)		__ioremap((addr), (size), __pgprot(PROT_DEVICE_nGnRE))
 #define iounmap				__iounmap
 
 /*

arch/avr32/include/asm/cmpxchg.h

@@ -70,8 +70,6 @@ extern unsigned long __cmpxchg_u64_unsupported_on_32bit_kernels(
    if something tries to do an invalid cmpxchg().  */
 extern void __cmpxchg_called_with_bad_pointer(void);
 
-#define __HAVE_ARCH_CMPXCHG 1
-
 static inline unsigned long __cmpxchg(volatile void *ptr, unsigned long old,
 				      unsigned long new, int size)
 {

arch/avr32/include/asm/io.h

@@ -296,6 +296,7 @@ extern void __iounmap(void __iomem *addr);
 	__iounmap(addr)
 
 #define ioremap_wc ioremap_nocache
+#define ioremap_wt ioremap_nocache
 
 #define cached(addr) P1SEGADDR(addr)
 #define uncached(addr) P2SEGADDR(addr)

arch/frv/include/asm/io.h

@@ -17,6 +17,8 @@
 
 #ifdef __KERNEL__
 
+#define ARCH_HAS_IOREMAP_WT
+
 #include <linux/types.h>
 #include <asm/virtconvert.h>
 #include <asm/string.h>
@@ -265,7 +267,7 @@ static inline void __iomem *ioremap_nocache(unsigned long physaddr, unsigned lon
 	return __ioremap(physaddr, size, IOMAP_NOCACHE_SER);
 }
 
-static inline void __iomem *ioremap_writethrough(unsigned long physaddr, unsigned long size)
+static inline void __iomem *ioremap_wt(unsigned long physaddr, unsigned long size)
 {
 	return __ioremap(physaddr, size, IOMAP_WRITETHROUGH);
 }

arch/hexagon/include/asm/cmpxchg.h

@@ -64,7 +64,6 @@ static inline unsigned long __xchg(unsigned long x, volatile void *ptr,
  *  looks just like atomic_cmpxchg on our arch currently with a bunch of
  *  variable casting.
  */
-#define __HAVE_ARCH_CMPXCHG 1
 
 #define cmpxchg(ptr, old, new)					\
 ({								\

arch/ia64/include/asm/barrier.h

@@ -77,12 +77,7 @@ do {									\
 	___p1;								\
 })
 
-/*
- * XXX check on this ---I suspect what Linus really wants here is
- * acquire vs release semantics but we can't discuss this stuff with
- * Linus just yet.  Grrr...
- */
-#define set_mb(var, value)	do { (var) = (value); mb(); } while (0)
+#define smp_store_mb(var, value)	do { WRITE_ONCE(var, value); mb(); } while (0)
 
 /*
  * The group barrier in front of the rsm & ssm are necessary to ensure

arch/ia64/include/uapi/asm/cmpxchg.h

@@ -61,8 +61,6 @@ extern void ia64_xchg_called_with_bad_pointer(void);
  * indicated by comparing RETURN with OLD.
  */
 
-#define __HAVE_ARCH_CMPXCHG 1
-
 /*
  * This function doesn't exist, so you'll get a linker error
  * if something tries to do an invalid cmpxchg().

arch/ia64/pci/pci.c

@@ -478,9 +478,16 @@ struct pci_bus *pci_acpi_scan_root(struct acpi_pci_root *root)
 
 int pcibios_root_bridge_prepare(struct pci_host_bridge *bridge)
 {
-	struct pci_controller *controller = bridge->bus->sysdata;
-
-	ACPI_COMPANION_SET(&bridge->dev, controller->companion);
+	/*
+	 * We pass NULL as parent to pci_create_root_bus(), so if it is not NULL
+	 * here, pci_create_root_bus() has been called by someone else and
+	 * sysdata is likely to be different from what we expect.  Let it go in
+	 * that case.
+	 */
+	if (!bridge->dev.parent) {
+		struct pci_controller *controller = bridge->bus->sysdata;
+		ACPI_COMPANION_SET(&bridge->dev, controller->companion);
+	}
 	return 0;
 }
 

arch/m32r/include/asm/cmpxchg.h

@@ -107,8 +107,6 @@ __xchg_local(unsigned long x, volatile void *ptr, int size)
 	((__typeof__(*(ptr)))__xchg_local((unsigned long)(x), (ptr),	\
 			sizeof(*(ptr))))
 
-#define __HAVE_ARCH_CMPXCHG	1
-
 static inline unsigned long
 __cmpxchg_u32(volatile unsigned int *p, unsigned int old, unsigned int new)
 {

arch/m32r/include/asm/io.h

@@ -68,6 +68,7 @@ static inline void __iomem *ioremap(unsigned long offset, unsigned long size)
 extern void iounmap(volatile void __iomem *addr);
 #define ioremap_nocache(off,size) ioremap(off,size)
 #define ioremap_wc ioremap_nocache
+#define ioremap_wt ioremap_nocache
 
 /*
  * IO bus memory addresses are also 1:1 with the physical address

arch/m68k/include/asm/cmpxchg.h

@@ -90,7 +90,6 @@ extern unsigned long __invalid_cmpxchg_size(volatile void *,
  * indicated by comparing RETURN with OLD.
  */
 #ifdef CONFIG_RMW_INSNS
-#define __HAVE_ARCH_CMPXCHG	1
 
 static inline unsigned long __cmpxchg(volatile void *p, unsigned long old,
 				      unsigned long new, int size)

arch/m68k/include/asm/io_mm.h

@@ -20,6 +20,8 @@
 
 #ifdef __KERNEL__
 
+#define ARCH_HAS_IOREMAP_WT
+
 #include <linux/compiler.h>
 #include <asm/raw_io.h>
 #include <asm/virtconvert.h>
@@ -465,7 +467,7 @@ static inline void __iomem *ioremap_nocache(unsigned long physaddr, unsigned lon
 {
 	return __ioremap(physaddr, size, IOMAP_NOCACHE_SER);
 }
-static inline void __iomem *ioremap_writethrough(unsigned long physaddr,
+static inline void __iomem *ioremap_wt(unsigned long physaddr,
 					 unsigned long size)
 {
 	return __ioremap(physaddr, size, IOMAP_WRITETHROUGH);

arch/m68k/include/asm/io_no.h

@@ -3,6 +3,8 @@
 
 #ifdef __KERNEL__
 
+#define ARCH_HAS_IOREMAP_WT
+
 #include <asm/virtconvert.h>
 #include <asm-generic/iomap.h>
 
@@ -153,7 +155,7 @@ static inline void *ioremap_nocache(unsigned long physaddr, unsigned long size)
 {
 	return __ioremap(physaddr, size, IOMAP_NOCACHE_SER);
 }
-static inline void *ioremap_writethrough(unsigned long physaddr, unsigned long size)
+static inline void *ioremap_wt(unsigned long physaddr, unsigned long size)
 {
 	return __ioremap(physaddr, size, IOMAP_WRITETHROUGH);
 }

arch/metag/include/asm/barrier.h

@@ -84,7 +84,7 @@ static inline void fence(void)
 #define read_barrier_depends()		do { } while (0)
 #define smp_read_barrier_depends()	do { } while (0)
 
-#define set_mb(var, value) do { var = value; smp_mb(); } while (0)
+#define smp_store_mb(var, value) do { WRITE_ONCE(var, value); smp_mb(); } while (0)
 
 #define smp_store_release(p, v)						\
 do {									\

arch/metag/include/asm/cmpxchg.h

@@ -51,8 +51,6 @@ static inline unsigned long __cmpxchg(volatile void *ptr, unsigned long old,
 	return old;
 }
 
-#define __HAVE_ARCH_CMPXCHG 1
-
 #define cmpxchg(ptr, o, n)						\
 	({								\
 		__typeof__(*(ptr)) _o_ = (o);				\

arch/metag/include/asm/io.h

@@ -160,6 +160,9 @@ extern void __iounmap(void __iomem *addr);
 #define ioremap_wc(offset, size)                \
 	__ioremap((offset), (size), _PAGE_WR_COMBINE)
 
+#define ioremap_wt(offset, size)                \
+	__ioremap((offset), (size), 0)
+
 #define iounmap(addr)                           \
 	__iounmap(addr)
 

arch/microblaze/include/asm/io.h

@@ -39,10 +39,10 @@ extern resource_size_t isa_mem_base;
 extern void iounmap(void __iomem *addr);
 
 extern void __iomem *ioremap(phys_addr_t address, unsigned long size);
-#define ioremap_writethrough(addr, size)	ioremap((addr), (size))
 #define ioremap_nocache(addr, size)		ioremap((addr), (size))
 #define ioremap_fullcache(addr, size)		ioremap((addr), (size))
 #define ioremap_wc(addr, size)			ioremap((addr), (size))
+#define ioremap_wt(addr, size)			ioremap((addr), (size))
 
 #endif /* CONFIG_MMU */
 

arch/mips/ath79/prom.c

@@ -1,6 +1,7 @@
 /*
  *  Atheros AR71XX/AR724X/AR913X specific prom routines
  *
+ *  Copyright (C) 2015 Laurent Fasnacht <l@libres.ch>
  *  Copyright (C) 2008-2010 Gabor Juhos <juhosg@openwrt.org>
  *  Copyright (C) 2008 Imre Kaloz <kaloz@openwrt.org>
  *
@@ -25,12 +26,14 @@ void __init prom_init(void)
 {
 	fw_init_cmdline();
 
+#ifdef CONFIG_BLK_DEV_INITRD
 	/* Read the initrd address from the firmware environment */
 	initrd_start = fw_getenvl("initrd_start");
 	if (initrd_start) {
 		initrd_start = KSEG0ADDR(initrd_start);
 		initrd_end = initrd_start + fw_getenvl("initrd_size");
 	}
+#endif
 }
 
 void __init prom_free_prom_memory(void)

arch/mips/configs/fuloong2e_defconfig

@@ -194,7 +194,7 @@ CONFIG_USB_WUSB_CBAF=m
 CONFIG_USB_C67X00_HCD=m
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
-CONFIG_USB_ISP1760_HCD=m
+CONFIG_USB_ISP1760=m
 CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_UHCI_HCD=m
 CONFIG_USB_R8A66597_HCD=m

arch/mips/include/asm/barrier.h

@@ -112,8 +112,8 @@
 #define __WEAK_LLSC_MB		"		\n"
 #endif
 
-#define set_mb(var, value) \
-	do { var = value; smp_mb(); } while (0)
+#define smp_store_mb(var, value) \
+	do { WRITE_ONCE(var, value); smp_mb(); } while (0)
 
 #define smp_llsc_mb()	__asm__ __volatile__(__WEAK_LLSC_MB : : :"memory")
 

arch/mips/include/asm/cmpxchg.h

@@ -138,8 +138,6 @@ static inline unsigned long __xchg(unsigned long x, volatile void * ptr, int siz
 		__xchg((unsigned long)(x), (ptr), sizeof(*(ptr))));	\
 })
 
-#define __HAVE_ARCH_CMPXCHG 1
-
 #define __cmpxchg_asm(ld, st, m, old, new)				\
 ({									\
 	__typeof(*(m)) __ret;						\

arch/mips/kernel/irq.c

@@ -29,7 +29,7 @@
 int kgdb_early_setup;
 #endif
 
-static unsigned long irq_map[NR_IRQS / BITS_PER_LONG];
+static DECLARE_BITMAP(irq_map, NR_IRQS);
 
 int allocate_irqno(void)
 {

arch/mips/kernel/smp-bmips.c

@@ -444,7 +444,7 @@ struct plat_smp_ops bmips5000_smp_ops = {
 static void bmips_wr_vec(unsigned long dst, char *start, char *end)
 {
 	memcpy((void *)dst, start, end - start);
-	dma_cache_wback((unsigned long)start, end - start);
+	dma_cache_wback(dst, end - start);
 	local_flush_icache_range(dst, dst + (end - start));
 	instruction_hazard();
 }

arch/mips/lib/strnlen_user.S

@@ -34,7 +34,12 @@ LEAF(__strnlen_\func\()_asm)
 FEXPORT(__strnlen_\func\()_nocheck_asm)
 	move		v0, a0
 	PTR_ADDU	a1, a0			# stop pointer
-1:	beq		v0, a1, 1f		# limit reached?
+1:
+#ifdef CONFIG_CPU_DADDI_WORKAROUNDS
+	.set		noat
+	li		AT, 1
+#endif
+	beq		v0, a1, 1f		# limit reached?
 .ifeqs "\func", "kernel"
 	EX(lb, t0, (v0), .Lfault\@)
 .else
@@ -42,7 +47,13 @@ FEXPORT(__strnlen_\func\()_nocheck_asm)
 .endif
 	.set		noreorder
 	bnez		t0, 1b
-1:	 PTR_ADDIU	v0, 1
+1:
+#ifndef CONFIG_CPU_DADDI_WORKAROUNDS
+	 PTR_ADDIU	v0, 1
+#else
+	 PTR_ADDU	v0, AT
+	.set		at
+#endif
 	.set		reorder
 	PTR_SUBU	v0, a0
 	jr		ra

arch/mn10300/include/asm/io.h

@@ -282,6 +282,7 @@ static inline void __iomem *ioremap_nocache(unsigned long offset, unsigned long
 }
 
 #define ioremap_wc ioremap_nocache
+#define ioremap_wt ioremap_nocache
 
 static inline void iounmap(void __iomem *addr)
 {

arch/nios2/include/asm/io.h

@@ -46,6 +46,7 @@ static inline void iounmap(void __iomem *addr)
 }
 
 #define ioremap_wc ioremap_nocache
+#define ioremap_wt ioremap_nocache
 
 /* Pages to physical address... */
 #define page_to_phys(page)	virt_to_phys(page_to_virt(page))

arch/parisc/include/asm/cmpxchg.h

@@ -46,8 +46,6 @@ __xchg(unsigned long x, __volatile__ void *ptr, int size)
 #define xchg(ptr, x) \
 	((__typeof__(*(ptr)))__xchg((unsigned long)(x), (ptr), sizeof(*(ptr))))
 
-#define __HAVE_ARCH_CMPXCHG	1
-
 /* bug catcher for when unsupported size is used - won't link */
 extern void __cmpxchg_called_with_bad_pointer(void);
 

arch/powerpc/include/asm/barrier.h

@@ -34,7 +34,7 @@
 #define rmb()  __asm__ __volatile__ ("sync" : : : "memory")
 #define wmb()  __asm__ __volatile__ ("sync" : : : "memory")
 
-#define set_mb(var, value)	do { var = value; mb(); } while (0)
+#define smp_store_mb(var, value)	do { WRITE_ONCE(var, value); mb(); } while (0)
 
 #ifdef __SUBARCH_HAS_LWSYNC
 #    define SMPWMB      LWSYNC

arch/powerpc/include/asm/cmpxchg.h

@@ -144,7 +144,6 @@ __xchg_local(volatile void *ptr, unsigned long x, unsigned int size)
  * Compare and exchange - if *p == old, set it to new,
  * and return the old value of *p.
  */
-#define __HAVE_ARCH_CMPXCHG	1
 
 static __always_inline unsigned long
 __cmpxchg_u32(volatile unsigned int *p, unsigned long old, unsigned long new)

arch/powerpc/kernel/mce.c

@@ -73,7 +73,7 @@ void save_mce_event(struct pt_regs *regs, long handled,
 		    uint64_t nip, uint64_t addr)
 {
 	uint64_t srr1;
-	int index = __this_cpu_inc_return(mce_nest_count);
+	int index = __this_cpu_inc_return(mce_nest_count) - 1;
 	struct machine_check_event *mce = this_cpu_ptr(&mce_event[index]);
 
 	/*
@@ -184,7 +184,7 @@ void machine_check_queue_event(void)
 	if (!get_mce_event(&evt, MCE_EVENT_RELEASE))
 		return;
 
-	index = __this_cpu_inc_return(mce_queue_count);
+	index = __this_cpu_inc_return(mce_queue_count) - 1;
 	/* If queue is full, just return for now. */
 	if (index >= MAX_MC_EVT) {
 		__this_cpu_dec(mce_queue_count);

arch/powerpc/kernel/vmlinux.lds.S

@@ -213,6 +213,7 @@ SECTIONS
 		*(.opd)
 	}
 
+	. = ALIGN(256);
 	.got : AT(ADDR(.got) - LOAD_OFFSET) {
 		__toc_start = .;
 #ifndef CONFIG_RELOCATABLE

arch/powerpc/kvm/book3s_hv.c

@@ -1952,7 +1952,7 @@ static void post_guest_process(struct kvmppc_vcore *vc)
  */
 static noinline void kvmppc_run_core(struct kvmppc_vcore *vc)
 {
-	struct kvm_vcpu *vcpu;
+	struct kvm_vcpu *vcpu, *vnext;
 	int i;
 	int srcu_idx;
 
@@ -1982,7 +1982,8 @@ static noinline void kvmppc_run_core(struct kvmppc_vcore *vc)
 	 */
 	if ((threads_per_core > 1) &&
 	    ((vc->num_threads > threads_per_subcore) || !on_primary_thread())) {
-		list_for_each_entry(vcpu, &vc->runnable_threads, arch.run_list) {
+		list_for_each_entry_safe(vcpu, vnext, &vc->runnable_threads,
+					 arch.run_list) {
 			vcpu->arch.ret = -EBUSY;
 			kvmppc_remove_runnable(vc, vcpu);
 			wake_up(&vcpu->arch.cpu_run);

arch/powerpc/mm/hugetlbpage.c

@@ -689,27 +689,34 @@ void hugetlb_free_pgd_range(struct mmu_gather *tlb,
 struct page *
 follow_huge_addr(struct mm_struct *mm, unsigned long address, int write)
 {
-	pte_t *ptep;
-	struct page *page;
+	pte_t *ptep, pte;
 	unsigned shift;
 	unsigned long mask, flags;
+	struct page *page = ERR_PTR(-EINVAL);
+
+	local_irq_save(flags);
+	ptep = find_linux_pte_or_hugepte(mm->pgd, address, &shift);
+	if (!ptep)
+		goto no_page;
+	pte = READ_ONCE(*ptep);
 	/*
+	 * Verify it is a huge page else bail.
 	 * Transparent hugepages are handled by generic code. We can skip them
 	 * here.
 	 */
-	local_irq_save(flags);
-	ptep = find_linux_pte_or_hugepte(mm->pgd, address, &shift);
+	if (!shift || pmd_trans_huge(__pmd(pte_val(pte))))
+		goto no_page;
 
-	/* Verify it is a huge page else bail. */
-	if (!ptep || !shift || pmd_trans_huge(*(pmd_t *)ptep)) {
-		local_irq_restore(flags);
-		return ERR_PTR(-EINVAL);
+	if (!pte_present(pte)) {
+		page = NULL;
+		goto no_page;
 	}
 	mask = (1UL << shift) - 1;
-	page = pte_page(*ptep);
+	page = pte_page(pte);
 	if (page)
 		page += (address & mask) / PAGE_SIZE;
 
+no_page:
 	local_irq_restore(flags);
 	return page;
 }

arch/powerpc/mm/pgtable_64.c

@@ -839,6 +839,17 @@ pmd_t pmdp_get_and_clear(struct mm_struct *mm,
 	 * hash fault look at them.
 	 */
 	memset(pgtable, 0, PTE_FRAG_SIZE);
+	/*
+	 * Serialize against find_linux_pte_or_hugepte which does lock-less
+	 * lookup in page tables with local interrupts disabled. For huge pages
+	 * it casts pmd_t to pte_t. Since format of pte_t is different from
+	 * pmd_t we want to prevent transit from pmd pointing to page table
+	 * to pmd pointing to huge page (and back) while interrupts are disabled.
+	 * We clear pmd to possibly replace it with page table pointer in
+	 * different code paths. So make sure we wait for the parallel
+	 * find_linux_pte_or_hugepage to finish.
+	 */
+	kick_all_cpus_sync();
 	return old_pmd;
 }
 

arch/s390/crypto/ghash_s390.c

@@ -16,11 +16,12 @@
 #define GHASH_DIGEST_SIZE	16
 
 struct ghash_ctx {
-	u8 icv[16];
-	u8 key[16];
+	u8 key[GHASH_BLOCK_SIZE];
 };
 
 struct ghash_desc_ctx {
+	u8 icv[GHASH_BLOCK_SIZE];
+	u8 key[GHASH_BLOCK_SIZE];
 	u8 buffer[GHASH_BLOCK_SIZE];
 	u32 bytes;
 };
@@ -28,8 +29,10 @@ struct ghash_desc_ctx {
 static int ghash_init(struct shash_desc *desc)
 {
 	struct ghash_desc_ctx *dctx = shash_desc_ctx(desc);
+	struct ghash_ctx *ctx = crypto_shash_ctx(desc->tfm);
 
 	memset(dctx, 0, sizeof(*dctx));
+	memcpy(dctx->key, ctx->key, GHASH_BLOCK_SIZE);
 
 	return 0;
 }
@@ -45,7 +48,6 @@ static int ghash_setkey(struct crypto_shash *tfm,
 	}
 
 	memcpy(ctx->key, key, GHASH_BLOCK_SIZE);
-	memset(ctx->icv, 0, GHASH_BLOCK_SIZE);
 
 	return 0;
 }
@@ -54,7 +56,6 @@ static int ghash_update(struct shash_desc *desc,
 			 const u8 *src, unsigned int srclen)
 {
 	struct ghash_desc_ctx *dctx = shash_desc_ctx(desc);
-	struct ghash_ctx *ctx = crypto_shash_ctx(desc->tfm);
 	unsigned int n;
 	u8 *buf = dctx->buffer;
 	int ret;
@@ -70,7 +71,7 @@ static int ghash_update(struct shash_desc *desc,
 		src += n;
 
 		if (!dctx->bytes) {
-			ret = crypt_s390_kimd(KIMD_GHASH, ctx, buf,
+			ret = crypt_s390_kimd(KIMD_GHASH, dctx, buf,
 					      GHASH_BLOCK_SIZE);
 			if (ret != GHASH_BLOCK_SIZE)
 				return -EIO;
@@ -79,7 +80,7 @@ static int ghash_update(struct shash_desc *desc,
 
 	n = srclen & ~(GHASH_BLOCK_SIZE - 1);
 	if (n) {
-		ret = crypt_s390_kimd(KIMD_GHASH, ctx, src, n);
+		ret = crypt_s390_kimd(KIMD_GHASH, dctx, src, n);
 		if (ret != n)
 			return -EIO;
 		src += n;
@@ -94,7 +95,7 @@ static int ghash_update(struct shash_desc *desc,
 	return 0;
 }
 
-static int ghash_flush(struct ghash_ctx *ctx, struct ghash_desc_ctx *dctx)
+static int ghash_flush(struct ghash_desc_ctx *dctx)
 {
 	u8 *buf = dctx->buffer;
 	int ret;
@@ -104,24 +105,24 @@ static int ghash_flush(struct ghash_ctx *ctx, struct ghash_desc_ctx *dctx)
 
 		memset(pos, 0, dctx->bytes);
 
-		ret = crypt_s390_kimd(KIMD_GHASH, ctx, buf, GHASH_BLOCK_SIZE);
+		ret = crypt_s390_kimd(KIMD_GHASH, dctx, buf, GHASH_BLOCK_SIZE);
 		if (ret != GHASH_BLOCK_SIZE)
 			return -EIO;
+
+		dctx->bytes = 0;
 	}
 
-	dctx->bytes = 0;
 	return 0;
 }
 
 static int ghash_final(struct shash_desc *desc, u8 *dst)
 {
 	struct ghash_desc_ctx *dctx = shash_desc_ctx(desc);
-	struct ghash_ctx *ctx = crypto_shash_ctx(desc->tfm);
 	int ret;
 
-	ret = ghash_flush(ctx, dctx);
+	ret = ghash_flush(dctx);
 	if (!ret)
-		memcpy(dst, ctx->icv, GHASH_BLOCK_SIZE);
+		memcpy(dst, dctx->icv, GHASH_BLOCK_SIZE);
 	return ret;
 }
 

arch/s390/crypto/prng.c

@@ -125,7 +125,7 @@ static int generate_entropy(u8 *ebuf, size_t nbytes)
 		/* fill page with urandom bytes */
 		get_random_bytes(pg, PAGE_SIZE);
 		/* exor page with stckf values */
-		for (n = 0; n < sizeof(PAGE_SIZE/sizeof(u64)); n++) {
+		for (n = 0; n < PAGE_SIZE / sizeof(u64); n++) {
 			u64 *p = ((u64 *)pg) + n;
 			*p ^= get_tod_clock_fast();
 		}

arch/s390/include/asm/barrier.h

@@ -36,7 +36,7 @@
 #define smp_mb__before_atomic()		smp_mb()
 #define smp_mb__after_atomic()		smp_mb()
 
-#define set_mb(var, value)		do { var = value; mb(); } while (0)
+#define smp_store_mb(var, value)		do { WRITE_ONCE(var, value); mb(); } while (0)
 
 #define smp_store_release(p, v)						\
 do {									\

arch/s390/include/asm/cmpxchg.h

@@ -32,8 +32,6 @@
 	__old;								\
 })
 
-#define __HAVE_ARCH_CMPXCHG
-
 #define __cmpxchg_double_op(p1, p2, o1, o2, n1, n2, insn)		\
 ({									\
 	register __typeof__(*(p1)) __old1 asm("2") = (o1);		\

arch/s390/include/asm/io.h

@@ -29,6 +29,7 @@ void unxlate_dev_mem_ptr(phys_addr_t phys, void *addr);
 
 #define ioremap_nocache(addr, size)	ioremap(addr, size)
 #define ioremap_wc			ioremap_nocache
+#define ioremap_wt			ioremap_nocache
 
 static inline void __iomem *ioremap(unsigned long offset, unsigned long size)
 {

arch/s390/include/asm/pgtable.h

@@ -494,7 +494,7 @@ static inline int pmd_large(pmd_t pmd)
 	return (pmd_val(pmd) & _SEGMENT_ENTRY_LARGE) != 0;
 }
 
-static inline int pmd_pfn(pmd_t pmd)
+static inline unsigned long pmd_pfn(pmd_t pmd)
 {
 	unsigned long origin_mask;
 

arch/s390/net/bpf_jit_comp.c

@@ -443,8 +443,11 @@ static void bpf_jit_epilogue(struct bpf_jit *jit)
 
 /*
  * Compile one eBPF instruction into s390x code
+ *
+ * NOTE: Use noinline because for gcov (-fprofile-arcs) gcc allocates a lot of
+ * stack space for the large switch statement.
  */
-static int bpf_jit_insn(struct bpf_jit *jit, struct bpf_prog *fp, int i)
+static noinline int bpf_jit_insn(struct bpf_jit *jit, struct bpf_prog *fp, int i)
 {
 	struct bpf_insn *insn = &fp->insnsi[i];
 	int jmp_off, last, insn_count = 1;
@@ -588,8 +591,8 @@ static int bpf_jit_insn(struct bpf_jit *jit, struct bpf_prog *fp, int i)
 		EMIT4(0xb9160000, dst_reg, rc_reg);
 		break;
 	}
-	case BPF_ALU64 | BPF_DIV | BPF_X: /* dst = dst / (u32) src */
-	case BPF_ALU64 | BPF_MOD | BPF_X: /* dst = dst % (u32) src */
+	case BPF_ALU64 | BPF_DIV | BPF_X: /* dst = dst / src */
+	case BPF_ALU64 | BPF_MOD | BPF_X: /* dst = dst % src */
 	{
 		int rc_reg = BPF_OP(insn->code) == BPF_DIV ? REG_W1 : REG_W0;
 
@@ -602,10 +605,8 @@ static int bpf_jit_insn(struct bpf_jit *jit, struct bpf_prog *fp, int i)
 		EMIT4_IMM(0xa7090000, REG_W0, 0);
 		/* lgr %w1,%dst */
 		EMIT4(0xb9040000, REG_W1, dst_reg);
-		/* llgfr %dst,%src (u32 cast) */
-		EMIT4(0xb9160000, dst_reg, src_reg);
 		/* dlgr %w0,%dst */
-		EMIT4(0xb9870000, REG_W0, dst_reg);
+		EMIT4(0xb9870000, REG_W0, src_reg);
 		/* lgr %dst,%rc */
 		EMIT4(0xb9040000, dst_reg, rc_reg);
 		break;
@@ -632,8 +633,8 @@ static int bpf_jit_insn(struct bpf_jit *jit, struct bpf_prog *fp, int i)
 		EMIT4(0xb9160000, dst_reg, rc_reg);
 		break;
 	}
-	case BPF_ALU64 | BPF_DIV | BPF_K: /* dst = dst / (u32) imm */
-	case BPF_ALU64 | BPF_MOD | BPF_K: /* dst = dst % (u32) imm */
+	case BPF_ALU64 | BPF_DIV | BPF_K: /* dst = dst / imm */
+	case BPF_ALU64 | BPF_MOD | BPF_K: /* dst = dst % imm */
 	{
 		int rc_reg = BPF_OP(insn->code) == BPF_DIV ? REG_W1 : REG_W0;
 
@@ -649,7 +650,7 @@ static int bpf_jit_insn(struct bpf_jit *jit, struct bpf_prog *fp, int i)
 		EMIT4(0xb9040000, REG_W1, dst_reg);
 		/* dlg %w0,<d(imm)>(%l) */
 		EMIT6_DISP_LH(0xe3000000, 0x0087, REG_W0, REG_0, REG_L,
-			      EMIT_CONST_U64((u32) imm));
+			      EMIT_CONST_U64(imm));
 		/* lgr %dst,%rc */
 		EMIT4(0xb9040000, dst_reg, rc_reg);
 		break;

arch/score/include/asm/cmpxchg.h

@@ -42,8 +42,6 @@ static inline unsigned long __cmpxchg(volatile unsigned long *m,
 					(unsigned long)(o),	\
 					(unsigned long)(n)))
 
-#define __HAVE_ARCH_CMPXCHG	1
-
 #include <asm-generic/cmpxchg-local.h>
 
 #endif /* _ASM_SCORE_CMPXCHG_H */

arch/sh/include/asm/barrier.h

@@ -32,7 +32,7 @@
 #define ctrl_barrier()	__asm__ __volatile__ ("nop;nop;nop;nop;nop;nop;nop;nop")
 #endif
 
-#define set_mb(var, value) do { (void)xchg(&var, value); } while (0)
+#define smp_store_mb(var, value) do { (void)xchg(&var, value); } while (0)
 
 #include <asm-generic/barrier.h>
 

arch/sh/include/asm/cmpxchg.h

@@ -46,8 +46,6 @@ extern void __xchg_called_with_bad_pointer(void);
  * if something tries to do an invalid cmpxchg(). */
 extern void __cmpxchg_called_with_bad_pointer(void);
 
-#define __HAVE_ARCH_CMPXCHG 1
-
 static inline unsigned long __cmpxchg(volatile void * ptr, unsigned long old,
 		unsigned long new, int size)
 {

arch/sparc/include/asm/barrier_64.h

@@ -40,8 +40,8 @@ do {	__asm__ __volatile__("ba,pt	%%xcc, 1f\n\t" \
 #define dma_rmb()	rmb()
 #define dma_wmb()	wmb()
 
-#define set_mb(__var, __value) \
-	do { __var = __value; membar_safe("#StoreLoad"); } while(0)
+#define smp_store_mb(__var, __value) \
+	do { WRITE_ONCE(__var, __value); membar_safe("#StoreLoad"); } while(0)
 
 #ifdef CONFIG_SMP
 #define smp_mb()	mb()

arch/sparc/include/asm/cmpxchg_32.h

@@ -34,7 +34,6 @@ static inline unsigned long __xchg(unsigned long x, __volatile__ void * ptr, int
  *
  * Cribbed from <asm-parisc/atomic.h>
  */
-#define __HAVE_ARCH_CMPXCHG	1
 
 /* bug catcher for when unsupported size is used - won't link */
 void __cmpxchg_called_with_bad_pointer(void);

arch/sparc/include/asm/cmpxchg_64.h

@@ -65,8 +65,6 @@ static inline unsigned long __xchg(unsigned long x, __volatile__ void * ptr,
 
 #include <asm-generic/cmpxchg-local.h>
 
-#define __HAVE_ARCH_CMPXCHG 1
-
 static inline unsigned long
 __cmpxchg_u32(volatile int *m, int old, int new)
 {