staging: wilc1000: fix compiler warnings

This avoids the remaining warnings that one gets on a normal
build: unused variables, unused labels, and invalid printk
format strings.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/staging/wilc1000/linux_wlan.c

@@ -1025,7 +1025,6 @@ int repeat_power_cycle(perInterface_wlan_t *nic);
 static int linux_wlan_start_firmware(perInterface_wlan_t *nic)
 {
 
-	static int timeout = 5;
 	int ret = 0;
 	/* start firmware */
 	PRINT_D(INIT_DBG, "Starting Firmware ...\n");
@@ -1040,6 +1039,7 @@ static int linux_wlan_start_firmware(perInterface_wlan_t *nic)
 	ret = linux_wlan_lock_timeout(&g_linux_wlan->sync_event, 5000);
 	if (ret) {
 #ifdef COMPLEMENT_BOOT
+		static int timeout = 5;
 
 		if (timeout--) {
 			PRINT_D(INIT_DBG, "repeat power cycle[%d]", timeout);
@@ -1675,7 +1675,9 @@ _fail_2:
 	linux_wlan_unlock(&g_linux_wlan->rxq_event);
 	kthread_stop(g_linux_wlan->rxq_thread);
 
+#ifndef TCP_ENHANCEMENTS
 _fail_1:
+#endif
 	#if (RX_BH_TYPE == RX_BH_KTHREAD)
 	/*De-Initialize 1st thread*/
 	g_linux_wlan->close = 1;
@@ -1999,8 +2001,8 @@ _fail_fw_start_:
 _fail_irq_enable_:
 #if (defined WILC_SDIO) && (!defined WILC_SDIO_IRQ_GPIO)
 		disable_sdio_interrupt();
-#endif
 _fail_irq_init_:
+#endif
 #if (!defined WILC_SDIO) || (defined WILC_SDIO_IRQ_GPIO)
 		deinit_irq(g_linux_wlan);
 
@@ -2522,8 +2524,10 @@ void frmw_to_linux(uint8_t *buff, uint32_t size, uint32_t pkt_offset)
 	int stats;
 	unsigned char *buff_to_send = NULL;
 	struct sk_buff *skb;
+#ifndef TCP_ENHANCEMENTS
 	char *pu8UdpBuffer;
 	struct iphdr *ih;
+#endif
 	struct net_device *wilc_netdev;
 	perInterface_wlan_t *nic;
 

drivers/staging/wilc1000/linux_wlan_spi.c

@@ -102,9 +102,6 @@ int linux_spi_init(void *vp)
 
 	if (called == 0) {
 		called++;
-		if (&wilc_bus == NULL) {
-			PRINT_ER("wilc_bus address is NULL\n");
-		}
 		ret = spi_register_driver(&wilc_bus);
 	}
 

drivers/staging/wilc1000/wilc_spi.c

@@ -1194,10 +1194,10 @@ static int spi_init(wilc_wlan_inp_t *inp, wilc_debug_func func)
 		/* Read failed. Try with CRC off. This might happen when module
 		 * is removed but chip isn't reset*/
 		g_spi.crc_off = 1;
-		PRINT_ER("[wilc spi]: Failed internal read protocol with CRC on, retyring with CRC off...\n", __LINE__);
+		PRINT_ER("[wilc spi]: Failed internal read protocol with CRC on, retyring with CRC off...\n");
 		if (!spi_internal_read(WILC_SPI_PROTOCOL_OFFSET, &reg)) {
 			/* Reaad failed with both CRC on and off, something went bad */
-			PRINT_ER("[wilc spi]: Failed internal read protocol...\n", __LINE__);
+			PRINT_ER("[wilc spi]: Failed internal read protocol...\n");
 			return 0;
 		}
 	}

drivers/staging/wilc1000/wilc_wlan.c

@@ -894,8 +894,6 @@ INLINE void chip_wakeup(void)
 #endif
 void chip_sleep_manually(WILC_Uint32 u32SleepTime)
 {
-	uint32_t val32;
-
 	if (genuChipPSstate != CHIP_WAKEDUP) {
 		/* chip is already sleeping. Do nothing */
 		return;
@@ -2302,7 +2300,7 @@ int wilc_wlan_init(wilc_wlan_inp_t *inp, wilc_wlan_oup_t *oup)
 #else
 		g_wlan.tx_buffer = (uint8_t *)g_wlan.os_func.os_malloc(g_wlan.tx_buffer_size);
 #endif
-	PRINT_D(TX_DBG, "g_wlan.tx_buffer = 0x%x\n", g_wlan.tx_buffer);
+	PRINT_D(TX_DBG, "g_wlan.tx_buffer = %p\n", g_wlan.tx_buffer);
 
 	if (g_wlan.tx_buffer == WILC_NULL) {
 		/* ENOBUFS	105 */
@@ -2319,7 +2317,7 @@ int wilc_wlan_init(wilc_wlan_inp_t *inp, wilc_wlan_oup_t *oup)
   #else
 		g_wlan.rx_buffer = (uint8_t *)g_wlan.os_func.os_malloc(g_wlan.rx_buffer_size);
   #endif
-	PRINT_D(TX_DBG, "g_wlan.rx_buffer =0x%x\n", g_wlan.rx_buffer);
+	PRINT_D(TX_DBG, "g_wlan.rx_buffer =%p\n", g_wlan.rx_buffer);
 	if (g_wlan.rx_buffer == WILC_NULL) {
 		/* ENOBUFS	105 */
 		ret = -105;