Merge tag 'usb-serial-4.19-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next

Johan writes:

USB-serial updates for v4.19-rc1

Here are the USB-serial updates for 4.19-rc1, including:

 - gpio support for CP2102N devices
 - improved line-speed handling for cp210x
 - conversion to spin_lock_irqsave() in completion handlers
 - dropped kl5kusb105 support from the kl5kusb105 driver (sic!)

Included are also various lower-priority fixes and clean ups.

All but the final commit have been in linux-next, and with no reported
issues.

Signed-off-by: Johan Hovold <johan@kernel.org>

Documentation/usb/usb-serial.txt

@@ -418,15 +418,6 @@ Current status:
   why it is wise to cut down on the rate used is wise for large
   transfers until this is settled.
   
-Options supported:
-  If this driver is compiled as a module you can pass the following
-  options to it:
-  debug			- extra verbose debugging info
-  			  (default: 0; nonzero enables)
-  use_lowlatency	- use low_latency flag to speed up tty layer
-			  when reading from the device.
-			  (default: 0; nonzero enables)
-
   See http://www.uuhaus.de/linux/palmconnect.html for up-to-date
   information on this driver.
 

drivers/usb/serial/cp210x.c

@@ -239,11 +239,14 @@ MODULE_DEVICE_TABLE(usb, id_table);
 struct cp210x_serial_private {
 #ifdef CONFIG_GPIOLIB
 	struct gpio_chip	gc;
-	u8			config;
-	u8			gpio_mode;
 	bool			gpio_registered;
+	u8			gpio_pushpull;
+	u8			gpio_altfunc;
+	u8			gpio_input;
 #endif
 	u8			partnum;
+	speed_t			max_speed;
+	bool			use_actual_rate;
 };
 
 struct cp210x_port_private {
@@ -356,6 +359,7 @@ static struct usb_serial_driver * const serial_drivers[] = {
 #define CONTROL_WRITE_RTS	0x0200
 
 /* CP210X_VENDOR_SPECIFIC values */
+#define CP210X_READ_2NCONFIG	0x000E
 #define CP210X_READ_LATCH	0x00C2
 #define CP210X_GET_PARTNUM	0x370B
 #define CP210X_GET_PORTCONFIG	0x370C
@@ -369,6 +373,9 @@ static struct usb_serial_driver * const serial_drivers[] = {
 #define CP210X_PARTNUM_CP2104	0x04
 #define CP210X_PARTNUM_CP2105	0x05
 #define CP210X_PARTNUM_CP2108	0x08
+#define CP210X_PARTNUM_CP2102N_QFN28	0x20
+#define CP210X_PARTNUM_CP2102N_QFN24	0x21
+#define CP210X_PARTNUM_CP2102N_QFN20	0x22
 #define CP210X_PARTNUM_UNKNOWN	0xFF
 
 /* CP210X_GET_COMM_STATUS returns these 0x13 bytes */
@@ -462,6 +469,12 @@ struct cp210x_config {
 #define CP2105_GPIO1_RXLED_MODE		BIT(1)
 #define CP2105_GPIO1_RS485_MODE		BIT(2)
 
+/* CP2102N configuration array indices */
+#define CP210X_2NCONFIG_CONFIG_VERSION_IDX	2
+#define CP210X_2NCONFIG_GPIO_MODE_IDX		581
+#define CP210X_2NCONFIG_GPIO_RSTLATCH_IDX	587
+#define CP210X_2NCONFIG_GPIO_CONTROL_IDX	600
+
 /* CP210X_VENDOR_SPECIFIC, CP210X_WRITE_LATCH call writes these 0x2 bytes. */
 struct cp210x_gpio_write {
 	u8	mask;
@@ -767,48 +780,6 @@ static int cp210x_get_line_ctl(struct usb_serial_port *port, u16 *ctl)
 	return 0;
 }
 
-/*
- * cp210x_quantise_baudrate
- * Quantises the baud rate as per AN205 Table 1
- */
-static unsigned int cp210x_quantise_baudrate(unsigned int baud)
-{
-	if (baud <= 300)
-		baud = 300;
-	else if (baud <= 600)      baud = 600;
-	else if (baud <= 1200)     baud = 1200;
-	else if (baud <= 1800)     baud = 1800;
-	else if (baud <= 2400)     baud = 2400;
-	else if (baud <= 4000)     baud = 4000;
-	else if (baud <= 4803)     baud = 4800;
-	else if (baud <= 7207)     baud = 7200;
-	else if (baud <= 9612)     baud = 9600;
-	else if (baud <= 14428)    baud = 14400;
-	else if (baud <= 16062)    baud = 16000;
-	else if (baud <= 19250)    baud = 19200;
-	else if (baud <= 28912)    baud = 28800;
-	else if (baud <= 38601)    baud = 38400;
-	else if (baud <= 51558)    baud = 51200;
-	else if (baud <= 56280)    baud = 56000;
-	else if (baud <= 58053)    baud = 57600;
-	else if (baud <= 64111)    baud = 64000;
-	else if (baud <= 77608)    baud = 76800;
-	else if (baud <= 117028)   baud = 115200;
-	else if (baud <= 129347)   baud = 128000;
-	else if (baud <= 156868)   baud = 153600;
-	else if (baud <= 237832)   baud = 230400;
-	else if (baud <= 254234)   baud = 250000;
-	else if (baud <= 273066)   baud = 256000;
-	else if (baud <= 491520)   baud = 460800;
-	else if (baud <= 567138)   baud = 500000;
-	else if (baud <= 670254)   baud = 576000;
-	else if (baud < 1000000)
-		baud = 921600;
-	else if (baud > 2000000)
-		baud = 2000000;
-	return baud;
-}
-
 static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *port)
 {
 	int result;
@@ -1028,6 +999,75 @@ static void cp210x_get_termios_port(struct usb_serial_port *port,
 	*cflagp = cflag;
 }
 
+struct cp210x_rate {
+	speed_t rate;
+	speed_t high;
+};
+
+static const struct cp210x_rate cp210x_an205_table1[] = {
+	{ 300, 300 },
+	{ 600, 600 },
+	{ 1200, 1200 },
+	{ 1800, 1800 },
+	{ 2400, 2400 },
+	{ 4000, 4000 },
+	{ 4800, 4803 },
+	{ 7200, 7207 },
+	{ 9600, 9612 },
+	{ 14400, 14428 },
+	{ 16000, 16062 },
+	{ 19200, 19250 },
+	{ 28800, 28912 },
+	{ 38400, 38601 },
+	{ 51200, 51558 },
+	{ 56000, 56280 },
+	{ 57600, 58053 },
+	{ 64000, 64111 },
+	{ 76800, 77608 },
+	{ 115200, 117028 },
+	{ 128000, 129347 },
+	{ 153600, 156868 },
+	{ 230400, 237832 },
+	{ 250000, 254234 },
+	{ 256000, 273066 },
+	{ 460800, 491520 },
+	{ 500000, 567138 },
+	{ 576000, 670254 },
+	{ 921600, UINT_MAX }
+};
+
+/*
+ * Quantises the baud rate as per AN205 Table 1
+ */
+static speed_t cp210x_get_an205_rate(speed_t baud)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(cp210x_an205_table1); ++i) {
+		if (baud <= cp210x_an205_table1[i].high)
+			break;
+	}
+
+	return cp210x_an205_table1[i].rate;
+}
+
+static speed_t cp210x_get_actual_rate(struct usb_serial *serial, speed_t baud)
+{
+	struct cp210x_serial_private *priv = usb_get_serial_data(serial);
+	unsigned int prescale = 1;
+	unsigned int div;
+
+	baud = clamp(baud, 300u, priv->max_speed);
+
+	if (baud <= 365)
+		prescale = 4;
+
+	div = DIV_ROUND_CLOSEST(48000000, 2 * prescale * baud);
+	baud = 48000000 / (2 * prescale * div);
+
+	return baud;
+}
+
 /*
  * CP2101 supports the following baud rates:
  *
@@ -1057,16 +1097,24 @@ static void cp210x_get_termios_port(struct usb_serial_port *port,
 static void cp210x_change_speed(struct tty_struct *tty,
 		struct usb_serial_port *port, struct ktermios *old_termios)
 {
+	struct usb_serial *serial = port->serial;
+	struct cp210x_serial_private *priv = usb_get_serial_data(serial);
 	u32 baud;
 
 	baud = tty->termios.c_ospeed;
 
-	/* This maps the requested rate to a rate valid on cp2102 or cp2103,
-	 * or to an arbitrary rate in [1M,2M].
+	/*
+	 * This maps the requested rate to the actual rate, a valid rate on
+	 * cp2102 or cp2103, or to an arbitrary rate in [1M, max_speed].
 	 *
 	 * NOTE: B0 is not implemented.
 	 */
-	baud = cp210x_quantise_baudrate(baud);
+	if (priv->use_actual_rate)
+		baud = cp210x_get_actual_rate(serial, baud);
+	else if (baud < 1000000)
+		baud = cp210x_get_an205_rate(baud);
+	else if (baud > priv->max_speed)
+		baud = priv->max_speed;
 
 	dev_dbg(&port->dev, "%s - setting baud rate to %u\n", __func__, baud);
 	if (cp210x_write_u32_reg(port, CP210X_SET_BAUDRATE, baud)) {
@@ -1288,17 +1336,8 @@ static int cp210x_gpio_request(struct gpio_chip *gc, unsigned int offset)
 	struct usb_serial *serial = gpiochip_get_data(gc);
 	struct cp210x_serial_private *priv = usb_get_serial_data(serial);
 
-	switch (offset) {
-	case 0:
-		if (priv->config & CP2105_GPIO0_TXLED_MODE)
-			return -ENODEV;
-		break;
-	case 1:
-		if (priv->config & (CP2105_GPIO1_RXLED_MODE |
-				    CP2105_GPIO1_RS485_MODE))
-			return -ENODEV;
-		break;
-	}
+	if (priv->gpio_altfunc & BIT(offset))
+		return -ENODEV;
 
 	return 0;
 }
@@ -1306,10 +1345,15 @@ static int cp210x_gpio_request(struct gpio_chip *gc, unsigned int offset)
 static int cp210x_gpio_get(struct gpio_chip *gc, unsigned int gpio)
 {
 	struct usb_serial *serial = gpiochip_get_data(gc);
+	struct cp210x_serial_private *priv = usb_get_serial_data(serial);
+	u8 req_type = REQTYPE_DEVICE_TO_HOST;
 	int result;
 	u8 buf;
 
-	result = cp210x_read_vendor_block(serial, REQTYPE_INTERFACE_TO_HOST,
+	if (priv->partnum == CP210X_PARTNUM_CP2105)
+		req_type = REQTYPE_INTERFACE_TO_HOST;
+
+	result = cp210x_read_vendor_block(serial, req_type,
 					  CP210X_READ_LATCH, &buf, sizeof(buf));
 	if (result < 0)
 		return result;
@@ -1320,7 +1364,9 @@ static int cp210x_gpio_get(struct gpio_chip *gc, unsigned int gpio)
 static void cp210x_gpio_set(struct gpio_chip *gc, unsigned int gpio, int value)
 {
 	struct usb_serial *serial = gpiochip_get_data(gc);
+	struct cp210x_serial_private *priv = usb_get_serial_data(serial);
 	struct cp210x_gpio_write buf;
+	int result;
 
 	if (value == 1)
 		buf.state = BIT(gpio);
@@ -1329,25 +1375,68 @@ static void cp210x_gpio_set(struct gpio_chip *gc, unsigned int gpio, int value)
 
 	buf.mask = BIT(gpio);
 
-	cp210x_write_vendor_block(serial, REQTYPE_HOST_TO_INTERFACE,
-				  CP210X_WRITE_LATCH, &buf, sizeof(buf));
+	if (priv->partnum == CP210X_PARTNUM_CP2105) {
+		result = cp210x_write_vendor_block(serial,
+						   REQTYPE_HOST_TO_INTERFACE,
+						   CP210X_WRITE_LATCH, &buf,
+						   sizeof(buf));
+	} else {
+		u16 wIndex = buf.state << 8 | buf.mask;
+
+		result = usb_control_msg(serial->dev,
+					 usb_sndctrlpipe(serial->dev, 0),
+					 CP210X_VENDOR_SPECIFIC,
+					 REQTYPE_HOST_TO_DEVICE,
+					 CP210X_WRITE_LATCH,
+					 wIndex,
+					 NULL, 0, USB_CTRL_SET_TIMEOUT);
+	}
+
+	if (result < 0) {
+		dev_err(&serial->interface->dev, "failed to set GPIO value: %d\n",
+				result);
+	}
 }
 
 static int cp210x_gpio_direction_get(struct gpio_chip *gc, unsigned int gpio)
 {
-	/* Hardware does not support an input mode */
-	return 0;
+	struct usb_serial *serial = gpiochip_get_data(gc);
+	struct cp210x_serial_private *priv = usb_get_serial_data(serial);
+
+	return priv->gpio_input & BIT(gpio);
 }
 
 static int cp210x_gpio_direction_input(struct gpio_chip *gc, unsigned int gpio)
 {
-	/* Hardware does not support an input mode */
-	return -ENOTSUPP;
+	struct usb_serial *serial = gpiochip_get_data(gc);
+	struct cp210x_serial_private *priv = usb_get_serial_data(serial);
+
+	if (priv->partnum == CP210X_PARTNUM_CP2105) {
+		/* hardware does not support an input mode */
+		return -ENOTSUPP;
+	}
+
+	/* push-pull pins cannot be changed to be inputs */
+	if (priv->gpio_pushpull & BIT(gpio))
+		return -EINVAL;
+
+	/* make sure to release pin if it is being driven low */
+	cp210x_gpio_set(gc, gpio, 1);
+
+	priv->gpio_input |= BIT(gpio);
+
+	return 0;
 }
 
 static int cp210x_gpio_direction_output(struct gpio_chip *gc, unsigned int gpio,
 					int value)
 {
+	struct usb_serial *serial = gpiochip_get_data(gc);
+	struct cp210x_serial_private *priv = usb_get_serial_data(serial);
+
+	priv->gpio_input &= ~BIT(gpio);
+	cp210x_gpio_set(gc, gpio, value);
+
 	return 0;
 }
 
@@ -1360,11 +1449,11 @@ static int cp210x_gpio_set_config(struct gpio_chip *gc, unsigned int gpio,
 
 	/* Succeed only if in correct mode (this can't be set at runtime) */
 	if ((param == PIN_CONFIG_DRIVE_PUSH_PULL) &&
-	    (priv->gpio_mode & BIT(gpio)))
+	    (priv->gpio_pushpull & BIT(gpio)))
 		return 0;
 
 	if ((param == PIN_CONFIG_DRIVE_OPEN_DRAIN) &&
-	    !(priv->gpio_mode & BIT(gpio)))
+	    !(priv->gpio_pushpull & BIT(gpio)))
 		return 0;
 
 	return -ENOTSUPP;
@@ -1377,12 +1466,13 @@ static int cp210x_gpio_set_config(struct gpio_chip *gc, unsigned int gpio,
  * this driver that provide GPIO do so in a way that does not impact other
  * signals and are thus expected to have very different initialisation.
  */
-static int cp2105_shared_gpio_init(struct usb_serial *serial)
+static int cp2105_gpioconf_init(struct usb_serial *serial)
 {
 	struct cp210x_serial_private *priv = usb_get_serial_data(serial);
 	struct cp210x_pin_mode mode;
 	struct cp210x_config config;
 	u8 intf_num = cp210x_interface_num(serial);
+	u8 iface_config;
 	int result;
 
 	result = cp210x_read_vendor_block(serial, REQTYPE_DEVICE_TO_HOST,
@@ -1399,20 +1489,26 @@ static int cp2105_shared_gpio_init(struct usb_serial *serial)
 
 	/*  2 banks of GPIO - One for the pins taken from each serial port */
 	if (intf_num == 0) {
-		if (mode.eci == CP210X_PIN_MODE_MODEM)
+		if (mode.eci == CP210X_PIN_MODE_MODEM) {
+			/* mark all GPIOs of this interface as reserved */
+			priv->gpio_altfunc = 0xff;
 			return 0;
+		}
 
-		priv->config = config.eci_cfg;
-		priv->gpio_mode = (u8)((le16_to_cpu(config.gpio_mode) &
+		iface_config = config.eci_cfg;
+		priv->gpio_pushpull = (u8)((le16_to_cpu(config.gpio_mode) &
 						CP210X_ECI_GPIO_MODE_MASK) >>
 						CP210X_ECI_GPIO_MODE_OFFSET);
 		priv->gc.ngpio = 2;
 	} else if (intf_num == 1) {
-		if (mode.sci == CP210X_PIN_MODE_MODEM)
+		if (mode.sci == CP210X_PIN_MODE_MODEM) {
+			/* mark all GPIOs of this interface as reserved */
+			priv->gpio_altfunc = 0xff;
 			return 0;
+		}
 
-		priv->config = config.sci_cfg;
-		priv->gpio_mode = (u8)((le16_to_cpu(config.gpio_mode) &
+		iface_config = config.sci_cfg;
+		priv->gpio_pushpull = (u8)((le16_to_cpu(config.gpio_mode) &
 						CP210X_SCI_GPIO_MODE_MASK) >>
 						CP210X_SCI_GPIO_MODE_OFFSET);
 		priv->gc.ngpio = 3;
@@ -1420,6 +1516,125 @@ static int cp2105_shared_gpio_init(struct usb_serial *serial)
 		return -ENODEV;
 	}
 
+	/* mark all pins which are not in GPIO mode */
+	if (iface_config & CP2105_GPIO0_TXLED_MODE)	/* GPIO 0 */
+		priv->gpio_altfunc |= BIT(0);
+	if (iface_config & (CP2105_GPIO1_RXLED_MODE |	/* GPIO 1 */
+			CP2105_GPIO1_RS485_MODE))
+		priv->gpio_altfunc |= BIT(1);
+
+	/* driver implementation for CP2105 only supports outputs */
+	priv->gpio_input = 0;
+
+	return 0;
+}
+
+static int cp2102n_gpioconf_init(struct usb_serial *serial)
+{
+	struct cp210x_serial_private *priv = usb_get_serial_data(serial);
+	const u16 config_size = 0x02a6;
+	u8 gpio_rst_latch;
+	u8 config_version;
+	u8 gpio_pushpull;
+	u8 *config_buf;
+	u8 gpio_latch;
+	u8 gpio_ctrl;
+	int result;
+	u8 i;
+
+	/*
+	 * Retrieve device configuration from the device.
+	 * The array received contains all customization settings done at the
+	 * factory/manufacturer. Format of the array is documented at the
+	 * time of writing at:
+	 * https://www.silabs.com/community/interface/knowledge-base.entry.html/2017/03/31/cp2102n_setconfig-xsfa
+	 */
+	config_buf = kmalloc(config_size, GFP_KERNEL);
+	if (!config_buf)
+		return -ENOMEM;
+
+	result = cp210x_read_vendor_block(serial,
+					  REQTYPE_DEVICE_TO_HOST,
+					  CP210X_READ_2NCONFIG,
+					  config_buf,
+					  config_size);
+	if (result < 0) {
+		kfree(config_buf);
+		return result;
+	}
+
+	config_version = config_buf[CP210X_2NCONFIG_CONFIG_VERSION_IDX];
+	gpio_pushpull = config_buf[CP210X_2NCONFIG_GPIO_MODE_IDX];
+	gpio_ctrl = config_buf[CP210X_2NCONFIG_GPIO_CONTROL_IDX];
+	gpio_rst_latch = config_buf[CP210X_2NCONFIG_GPIO_RSTLATCH_IDX];
+
+	kfree(config_buf);
+
+	/* Make sure this is a config format we understand. */
+	if (config_version != 0x01)
+		return -ENOTSUPP;
+
+	/*
+	 * We only support 4 GPIOs even on the QFN28 package, because
+	 * config locations of GPIOs 4-6 determined using reverse
+	 * engineering revealed conflicting offsets with other
+	 * documented functions. So we'll just play it safe for now.
+	 */
+	priv->gc.ngpio = 4;
+
+	/*
+	 * Get default pin states after reset. Needed so we can determine
+	 * the direction of an open-drain pin.
+	 */
+	gpio_latch = (gpio_rst_latch >> 3) & 0x0f;
+
+	/* 0 indicates open-drain mode, 1 is push-pull */
+	priv->gpio_pushpull = (gpio_pushpull >> 3) & 0x0f;
+
+	/* 0 indicates GPIO mode, 1 is alternate function */
+	priv->gpio_altfunc = (gpio_ctrl >> 2) & 0x0f;
+
+	/*
+	 * The CP2102N does not strictly has input and output pin modes,
+	 * it only knows open-drain and push-pull modes which is set at
+	 * factory. An open-drain pin can function both as an
+	 * input or an output. We emulate input mode for open-drain pins
+	 * by making sure they are not driven low, and we do not allow
+	 * push-pull pins to be set as an input.
+	 */
+	for (i = 0; i < priv->gc.ngpio; ++i) {
+		/*
+		 * Set direction to "input" iff pin is open-drain and reset
+		 * value is 1.
+		 */
+		if (!(priv->gpio_pushpull & BIT(i)) && (gpio_latch & BIT(i)))
+			priv->gpio_input |= BIT(i);
+	}
+
+	return 0;
+}
+
+static int cp210x_gpio_init(struct usb_serial *serial)
+{
+	struct cp210x_serial_private *priv = usb_get_serial_data(serial);
+	int result;
+
+	switch (priv->partnum) {
+	case CP210X_PARTNUM_CP2105:
+		result = cp2105_gpioconf_init(serial);
+		break;
+	case CP210X_PARTNUM_CP2102N_QFN28:
+	case CP210X_PARTNUM_CP2102N_QFN24:
+	case CP210X_PARTNUM_CP2102N_QFN20:
+		result = cp2102n_gpioconf_init(serial);
+		break;
+	default:
+		return 0;
+	}
+
+	if (result < 0)
+		return result;
+
 	priv->gc.label = "cp210x";
 	priv->gc.request = cp210x_gpio_request;
 	priv->gc.get_direction = cp210x_gpio_direction_get;
@@ -1452,7 +1667,7 @@ static void cp210x_gpio_remove(struct usb_serial *serial)
 
 #else
 
-static int cp2105_shared_gpio_init(struct usb_serial *serial)
+static int cp210x_gpio_init(struct usb_serial *serial)
 {
 	return 0;
 }
@@ -1497,6 +1712,50 @@ static int cp210x_port_remove(struct usb_serial_port *port)
 	return 0;
 }
 
+static void cp210x_init_max_speed(struct usb_serial *serial)
+{
+	struct cp210x_serial_private *priv = usb_get_serial_data(serial);
+	bool use_actual_rate = false;
+	speed_t max;
+
+	switch (priv->partnum) {
+	case CP210X_PARTNUM_CP2101:
+		max = 921600;
+		break;
+	case CP210X_PARTNUM_CP2102:
+	case CP210X_PARTNUM_CP2103:
+		max = 1000000;
+		break;
+	case CP210X_PARTNUM_CP2104:
+		use_actual_rate = true;
+		max = 2000000;
+		break;
+	case CP210X_PARTNUM_CP2108:
+		max = 2000000;
+		break;
+	case CP210X_PARTNUM_CP2105:
+		if (cp210x_interface_num(serial) == 0) {
+			use_actual_rate = true;
+			max = 2000000;	/* ECI */
+		} else {
+			max = 921600;	/* SCI */
+		}
+		break;
+	case CP210X_PARTNUM_CP2102N_QFN28:
+	case CP210X_PARTNUM_CP2102N_QFN24:
+	case CP210X_PARTNUM_CP2102N_QFN20:
+		use_actual_rate = true;
+		max = 3000000;
+		break;
+	default:
+		max = 2000000;
+		break;
+	}
+
+	priv->max_speed = max;
+	priv->use_actual_rate = use_actual_rate;
+}
+
 static int cp210x_attach(struct usb_serial *serial)
 {
 	int result;
@@ -1517,12 +1776,12 @@ static int cp210x_attach(struct usb_serial *serial)
 
 	usb_set_serial_data(serial, priv);
 
-	if (priv->partnum == CP210X_PARTNUM_CP2105) {
-		result = cp2105_shared_gpio_init(serial);
-		if (result < 0) {
-			dev_err(&serial->interface->dev,
-				"GPIO initialisation failed, continuing without GPIO support\n");
-		}
+	cp210x_init_max_speed(serial);
+
+	result = cp210x_gpio_init(serial);
+	if (result < 0) {
+		dev_err(&serial->interface->dev, "GPIO initialisation failed: %d\n",
+				result);
 	}
 
 	return 0;

drivers/usb/serial/cyberjack.c

@@ -255,6 +255,7 @@ static void cyberjack_read_int_callback(struct urb *urb)
 	struct device *dev = &port->dev;
 	unsigned char *data = urb->transfer_buffer;
 	int status = urb->status;
+	unsigned long flags;
 	int result;
 
 	/* the urb might have been killed. */
@@ -270,13 +271,13 @@ static void cyberjack_read_int_callback(struct urb *urb)
 		/* This is a announcement of coming bulk_ins. */
 		unsigned short size = ((unsigned short)data[3]<<8)+data[2]+3;
 
-		spin_lock(&priv->lock);
+		spin_lock_irqsave(&priv->lock, flags);
 
 		old_rdtodo = priv->rdtodo;
 
 		if (old_rdtodo > SHRT_MAX - size) {
 			dev_dbg(dev, "To many bulk_in urbs to do.\n");
-			spin_unlock(&priv->lock);
+			spin_unlock_irqrestore(&priv->lock, flags);
 			goto resubmit;
 		}
 
@@ -285,7 +286,7 @@ static void cyberjack_read_int_callback(struct urb *urb)
 
 		dev_dbg(dev, "%s - rdtodo: %d\n", __func__, priv->rdtodo);
 
-		spin_unlock(&priv->lock);
+		spin_unlock_irqrestore(&priv->lock, flags);
 
 		if (!old_rdtodo) {
 			result = usb_submit_urb(port->read_urb, GFP_ATOMIC);
@@ -309,6 +310,7 @@ static void cyberjack_read_bulk_callback(struct urb *urb)
 	struct cyberjack_private *priv = usb_get_serial_port_data(port);
 	struct device *dev = &port->dev;
 	unsigned char *data = urb->transfer_buffer;
+	unsigned long flags;
 	short todo;
 	int result;
 	int status = urb->status;
@@ -325,7 +327,7 @@ static void cyberjack_read_bulk_callback(struct urb *urb)
 		tty_flip_buffer_push(&port->port);
 	}
 
-	spin_lock(&priv->lock);
+	spin_lock_irqsave(&priv->lock, flags);
 
 	/* Reduce urbs to do by one. */
 	priv->rdtodo -= urb->actual_length;
@@ -334,7 +336,7 @@ static void cyberjack_read_bulk_callback(struct urb *urb)
 		priv->rdtodo = 0;
 	todo = priv->rdtodo;
 
-	spin_unlock(&priv->lock);
+	spin_unlock_irqrestore(&priv->lock, flags);
 
 	dev_dbg(dev, "%s - rdtodo: %d\n", __func__, todo);
 
@@ -354,6 +356,7 @@ static void cyberjack_write_bulk_callback(struct urb *urb)
 	struct cyberjack_private *priv = usb_get_serial_port_data(port);
 	struct device *dev = &port->dev;
 	int status = urb->status;
+	unsigned long flags;
 
 	set_bit(0, &port->write_urbs_free);
 	if (status) {
@@ -362,7 +365,7 @@ static void cyberjack_write_bulk_callback(struct urb *urb)
 		return;
 	}
 
-	spin_lock(&priv->lock);
+	spin_lock_irqsave(&priv->lock, flags);
 
 	/* only do something if we have more data to send */
 	if (priv->wrfilled) {
@@ -406,7 +409,7 @@ static void cyberjack_write_bulk_callback(struct urb *urb)
 	}
 
 exit:
-	spin_unlock(&priv->lock);
+	spin_unlock_irqrestore(&priv->lock, flags);
 	usb_serial_port_softint(port);
 }
 

drivers/usb/serial/digi_acceleport.c

@@ -984,6 +984,7 @@ static void digi_write_bulk_callback(struct urb *urb)
 	struct usb_serial *serial;
 	struct digi_port *priv;
 	struct digi_serial *serial_priv;
+	unsigned long flags;
 	int ret = 0;
 	int status = urb->status;
 
@@ -1004,15 +1005,15 @@ static void digi_write_bulk_callback(struct urb *urb)
 	/* handle oob callback */
 	if (priv->dp_port_num == serial_priv->ds_oob_port_num) {
 		dev_dbg(&port->dev, "digi_write_bulk_callback: oob callback\n");
-		spin_lock(&priv->dp_port_lock);
+		spin_lock_irqsave(&priv->dp_port_lock, flags);
 		priv->dp_write_urb_in_use = 0;
 		wake_up_interruptible(&port->write_wait);
-		spin_unlock(&priv->dp_port_lock);
+		spin_unlock_irqrestore(&priv->dp_port_lock, flags);
 		return;
 	}
 
 	/* try to send any buffered data on this port */
-	spin_lock(&priv->dp_port_lock);
+	spin_lock_irqsave(&priv->dp_port_lock, flags);
 	priv->dp_write_urb_in_use = 0;
 	if (priv->dp_out_buf_len > 0) {
 		*((unsigned char *)(port->write_urb->transfer_buffer))
@@ -1035,7 +1036,7 @@ static void digi_write_bulk_callback(struct urb *urb)
 	/* lost the race in write_chan(). */
 	schedule_work(&priv->dp_wakeup_work);
 
-	spin_unlock(&priv->dp_port_lock);
+	spin_unlock_irqrestore(&priv->dp_port_lock, flags);
 	if (ret && ret != -EPERM)
 		dev_err_console(port,
 			"%s: usb_submit_urb failed, ret=%d, port=%d\n",
@@ -1381,11 +1382,12 @@ static int digi_read_inb_callback(struct urb *urb)
 	struct usb_serial_port *port = urb->context;
 	struct digi_port *priv = usb_get_serial_port_data(port);
 	unsigned char *buf = urb->transfer_buffer;
+	unsigned long flags;
 	int opcode;
 	int len;
 	int port_status;
 	unsigned char *data;
-	int flag, throttled;
+	int tty_flag, throttled;
 
 	/* short/multiple packet check */
 	if (urb->actual_length < 2) {
@@ -1407,7 +1409,7 @@ static int digi_read_inb_callback(struct urb *urb)
 		return -1;
 	}
 
-	spin_lock(&priv->dp_port_lock);
+	spin_lock_irqsave(&priv->dp_port_lock, flags);
 
 	/* check for throttle; if set, do not resubmit read urb */
 	/* indicate the read chain needs to be restarted on unthrottle */
@@ -1421,7 +1423,7 @@ static int digi_read_inb_callback(struct urb *urb)
 		data = &buf[3];
 
 		/* get flag from port_status */
-		flag = 0;
+		tty_flag = 0;
 
 		/* overrun is special, not associated with a char */
 		if (port_status & DIGI_OVERRUN_ERROR)
@@ -1430,21 +1432,21 @@ static int digi_read_inb_callback(struct urb *urb)
 		/* break takes precedence over parity, */
 		/* which takes precedence over framing errors */
 		if (port_status & DIGI_BREAK_ERROR)
-			flag = TTY_BREAK;
+			tty_flag = TTY_BREAK;
 		else if (port_status & DIGI_PARITY_ERROR)
-			flag = TTY_PARITY;
+			tty_flag = TTY_PARITY;
 		else if (port_status & DIGI_FRAMING_ERROR)
-			flag = TTY_FRAME;
+			tty_flag = TTY_FRAME;
 
 		/* data length is len-1 (one byte of len is port_status) */
 		--len;
 		if (len > 0) {
 			tty_insert_flip_string_fixed_flag(&port->port, data,
-					flag, len);
+					tty_flag, len);
 			tty_flip_buffer_push(&port->port);
 		}
 	}
-	spin_unlock(&priv->dp_port_lock);
+	spin_unlock_irqrestore(&priv->dp_port_lock, flags);
 
 	if (opcode == DIGI_CMD_RECEIVE_DISABLE)
 		dev_dbg(&port->dev, "%s: got RECEIVE_DISABLE\n", __func__);
@@ -1474,6 +1476,7 @@ static int digi_read_oob_callback(struct urb *urb)
 	struct digi_port *priv = usb_get_serial_port_data(port);
 	unsigned char *buf = urb->transfer_buffer;
 	int opcode, line, status, val;
+	unsigned long flags;
 	int i;
 	unsigned int rts;
 
@@ -1506,7 +1509,7 @@ static int digi_read_oob_callback(struct urb *urb)
 			rts = C_CRTSCTS(tty);
 
 		if (tty && opcode == DIGI_CMD_READ_INPUT_SIGNALS) {
-			spin_lock(&priv->dp_port_lock);
+			spin_lock_irqsave(&priv->dp_port_lock, flags);
 			/* convert from digi flags to termiox flags */
 			if (val & DIGI_READ_INPUT_SIGNALS_CTS) {
 				priv->dp_modem_signals |= TIOCM_CTS;
@@ -1530,12 +1533,12 @@ static int digi_read_oob_callback(struct urb *urb)
 			else
 				priv->dp_modem_signals &= ~TIOCM_CD;
 
-			spin_unlock(&priv->dp_port_lock);
+			spin_unlock_irqrestore(&priv->dp_port_lock, flags);
 		} else if (opcode == DIGI_CMD_TRANSMIT_IDLE) {
-			spin_lock(&priv->dp_port_lock);
+			spin_lock_irqsave(&priv->dp_port_lock, flags);
 			priv->dp_transmit_idle = 1;
 			wake_up_interruptible(&priv->dp_transmit_idle_wait);
-			spin_unlock(&priv->dp_port_lock);
+			spin_unlock_irqrestore(&priv->dp_port_lock, flags);
 		} else if (opcode == DIGI_CMD_IFLUSH_FIFO) {
 			wake_up_interruptible(&priv->dp_flush_wait);
 		}

drivers/usb/serial/io_edgeport.c

@@ -648,6 +648,7 @@ static void edge_interrupt_callback(struct urb *urb)
 	struct usb_serial_port *port;
 	unsigned char *data = urb->transfer_buffer;
 	int length = urb->actual_length;
+	unsigned long flags;
 	int bytes_avail;
 	int position;
 	int txCredits;
@@ -679,7 +680,7 @@ static void edge_interrupt_callback(struct urb *urb)
 		if (length > 1) {
 			bytes_avail = data[0] | (data[1] << 8);
 			if (bytes_avail) {
-				spin_lock(&edge_serial->es_lock);
+				spin_lock_irqsave(&edge_serial->es_lock, flags);
 				edge_serial->rxBytesAvail += bytes_avail;
 				dev_dbg(dev,
 					"%s - bytes_avail=%d, rxBytesAvail=%d, read_in_progress=%d\n",
@@ -702,7 +703,8 @@ static void edge_interrupt_callback(struct urb *urb)
 						edge_serial->read_in_progress = false;
 					}
 				}
-				spin_unlock(&edge_serial->es_lock);
+				spin_unlock_irqrestore(&edge_serial->es_lock,
+						       flags);
 			}
 		}
 		/* grab the txcredits for the ports if available */
@@ -715,9 +717,11 @@ static void edge_interrupt_callback(struct urb *urb)
 				port = edge_serial->serial->port[portNumber];
 				edge_port = usb_get_serial_port_data(port);
 				if (edge_port->open) {
-					spin_lock(&edge_port->ep_lock);
+					spin_lock_irqsave(&edge_port->ep_lock,
+							  flags);
 					edge_port->txCredits += txCredits;
-					spin_unlock(&edge_port->ep_lock);
+					spin_unlock_irqrestore(&edge_port->ep_lock,
+							       flags);
 					dev_dbg(dev, "%s - txcredits for port%d = %d\n",
 						__func__, portNumber,
 						edge_port->txCredits);
@@ -758,6 +762,7 @@ static void edge_bulk_in_callback(struct urb *urb)
 	int			retval;
 	__u16			raw_data_length;
 	int status = urb->status;
+	unsigned long flags;
 
 	if (status) {
 		dev_dbg(&urb->dev->dev, "%s - nonzero read bulk status received: %d\n",
@@ -777,7 +782,7 @@ static void edge_bulk_in_callback(struct urb *urb)
 
 	usb_serial_debug_data(dev, __func__, raw_data_length, data);
 
-	spin_lock(&edge_serial->es_lock);
+	spin_lock_irqsave(&edge_serial->es_lock, flags);
 
 	/* decrement our rxBytes available by the number that we just got */
 	edge_serial->rxBytesAvail -= raw_data_length;
@@ -801,7 +806,7 @@ static void edge_bulk_in_callback(struct urb *urb)
 		edge_serial->read_in_progress = false;
 	}
 
-	spin_unlock(&edge_serial->es_lock);
+	spin_unlock_irqrestore(&edge_serial->es_lock, flags);
 }
 
 

drivers/usb/serial/io_ti.c

@@ -1729,6 +1729,7 @@ static void edge_bulk_in_callback(struct urb *urb)
 	struct edgeport_port *edge_port = urb->context;
 	struct device *dev = &edge_port->port->dev;
 	unsigned char *data = urb->transfer_buffer;
+	unsigned long flags;
 	int retval = 0;
 	int port_number;
 	int status = urb->status;
@@ -1780,13 +1781,13 @@ static void edge_bulk_in_callback(struct urb *urb)
 
 exit:
 	/* continue read unless stopped */
-	spin_lock(&edge_port->ep_lock);
+	spin_lock_irqsave(&edge_port->ep_lock, flags);
 	if (edge_port->ep_read_urb_state == EDGE_READ_URB_RUNNING)
 		retval = usb_submit_urb(urb, GFP_ATOMIC);
 	else if (edge_port->ep_read_urb_state == EDGE_READ_URB_STOPPING)
 		edge_port->ep_read_urb_state = EDGE_READ_URB_STOPPED;
 
-	spin_unlock(&edge_port->ep_lock);
+	spin_unlock_irqrestore(&edge_port->ep_lock, flags);
 	if (retval)
 		dev_err(dev, "%s - usb_submit_urb failed with result %d\n", __func__, retval);
 }

drivers/usb/serial/ir-usb.c

@@ -132,7 +132,7 @@ irda_usb_find_class_desc(struct usb_serial *serial, unsigned int ifnum)
 			0, ifnum, desc, sizeof(*desc), 1000);
 
 	dev_dbg(&serial->dev->dev, "%s -  ret=%d\n", __func__, ret);
-	if (ret < sizeof(*desc)) {
+	if (ret < (int)sizeof(*desc)) {
 		dev_dbg(&serial->dev->dev,
 			"%s - class descriptor read %s (%d)\n", __func__,
 			(ret < 0) ? "failed" : "too short", ret);

drivers/usb/serial/iuu_phoenix.c

@@ -58,7 +58,6 @@ struct iuu_private {
 	u8 *buf;		/* used for initialize speed */
 	u8 len;
 	int vcc;		/* vcc (either 3 or 5 V) */
-	u32 baud;
 	u32 boost;
 	u32 clk;
 };
@@ -963,9 +962,6 @@ static int iuu_open(struct tty_struct *tty, struct usb_serial_port *port)
 	struct iuu_private *priv = usb_get_serial_port_data(port);
 
 	baud = tty->termios.c_ospeed;
-	tty->termios.c_ispeed = baud;
-	/* Re-encode speed */
-	tty_encode_baud_rate(tty, baud, baud);
 
 	dev_dbg(dev, "%s - baud %d\n", __func__, baud);
 	usb_clear_halt(serial->dev, port->write_urb->pipe);
@@ -991,7 +987,6 @@ static int iuu_open(struct tty_struct *tty, struct usb_serial_port *port)
 	if (boost < 100)
 		boost = 100;
 	priv->boost = boost;
-	priv->baud = baud;
 	switch (clockmode) {
 	case 2:		/*  3.680 Mhz */
 		priv->clk = IUU_CLK_3680000;

drivers/usb/serial/kl5kusb105.c

@@ -67,7 +67,6 @@ static int klsi_105_prepare_write_buffer(struct usb_serial_port *port,
  */
 static const struct usb_device_id id_table[] = {
 	{ USB_DEVICE(PALMCONNECT_VID, PALMCONNECT_PID) },
-	{ USB_DEVICE(KLSI_VID, KLSI_KL5KUSB105D_PID) },
 	{ }		/* Terminating entry */
 };
 

drivers/usb/serial/kl5kusb105.h

@@ -7,9 +7,6 @@
 #define PALMCONNECT_VID		0x0830
 #define PALMCONNECT_PID		0x0080
 
-#define KLSI_VID		0x05e9
-#define KLSI_KL5KUSB105D_PID	0x00c0
-
 /* Vendor commands: */
 
 

drivers/usb/serial/kobil_sct.c

@@ -190,8 +190,10 @@ static int kobil_open(struct tty_struct *tty, struct usb_serial_port *port)
 			  KOBIL_TIMEOUT
 	);
 	dev_dbg(dev, "%s - Send get_HW_version URB returns: %i\n", __func__, result);
-	dev_dbg(dev, "Hardware version: %i.%i.%i\n", transfer_buffer[0],
-		transfer_buffer[1], transfer_buffer[2]);
+	if (result >= 3) {
+		dev_dbg(dev, "Hardware version: %i.%i.%i\n", transfer_buffer[0],
+				transfer_buffer[1], transfer_buffer[2]);
+	}
 
 	/* get firmware version */
 	result = usb_control_msg(port->serial->dev,
@@ -205,8 +207,10 @@ static int kobil_open(struct tty_struct *tty, struct usb_serial_port *port)
 			  KOBIL_TIMEOUT
 	);
 	dev_dbg(dev, "%s - Send get_FW_version URB returns: %i\n", __func__, result);
-	dev_dbg(dev, "Firmware version: %i.%i.%i\n", transfer_buffer[0],
-		transfer_buffer[1], transfer_buffer[2]);
+	if (result >= 3) {
+		dev_dbg(dev, "Firmware version: %i.%i.%i\n", transfer_buffer[0],
+				transfer_buffer[1], transfer_buffer[2]);
+	}
 
 	if (priv->device_type == KOBIL_ADAPTER_B_PRODUCT_ID ||
 			priv->device_type == KOBIL_ADAPTER_K_PRODUCT_ID) {
@@ -393,12 +397,20 @@ static int kobil_tiocmget(struct tty_struct *tty)
 			  transfer_buffer_length,
 			  KOBIL_TIMEOUT);
 
-	dev_dbg(&port->dev, "%s - Send get_status_line_state URB returns: %i. Statusline: %02x\n",
-		__func__, result, transfer_buffer[0]);
+	dev_dbg(&port->dev, "Send get_status_line_state URB returns: %i\n",
+			result);
+	if (result < 1) {
+		if (result >= 0)
+			result = -EIO;
+		goto out_free;
+	}
+
+	dev_dbg(&port->dev, "Statusline: %02x\n", transfer_buffer[0]);
 
 	result = 0;
 	if ((transfer_buffer[0] & SUSBCR_GSL_DSR) != 0)
 		result = TIOCM_DSR;
+out_free:
 	kfree(transfer_buffer);
 	return result;
 }

drivers/usb/serial/mos7720.c

@@ -340,14 +340,15 @@ static void async_complete(struct urb *urb)
 {
 	struct urbtracker *urbtrack = urb->context;
 	int status = urb->status;
+	unsigned long flags;
 
 	if (unlikely(status))
 		dev_dbg(&urb->dev->dev, "%s - nonzero urb status received: %d\n", __func__, status);
 
 	/* remove the urbtracker from the active_urbs list */
-	spin_lock(&urbtrack->mos_parport->listlock);
+	spin_lock_irqsave(&urbtrack->mos_parport->listlock, flags);
 	list_del(&urbtrack->urblist_entry);
-	spin_unlock(&urbtrack->mos_parport->listlock);
+	spin_unlock_irqrestore(&urbtrack->mos_parport->listlock, flags);
 	kref_put(&urbtrack->ref_count, destroy_urbtracker);
 }
 
@@ -1526,8 +1527,6 @@ static void change_port_settings(struct tty_struct *tty,
 	struct usb_serial *serial;
 	int baud;
 	unsigned cflag;
-	unsigned iflag;
-	__u8 mask = 0xff;
 	__u8 lData;
 	__u8 lParity;
 	__u8 lStop;
@@ -1551,23 +1550,19 @@ static void change_port_settings(struct tty_struct *tty,
 	lParity = 0x00;	/* No parity */
 
 	cflag = tty->termios.c_cflag;
-	iflag = tty->termios.c_iflag;
 
 	/* Change the number of bits */
 	switch (cflag & CSIZE) {
 	case CS5:
 		lData = UART_LCR_WLEN5;
-		mask = 0x1f;
 		break;
 
 	case CS6:
 		lData = UART_LCR_WLEN6;
-		mask = 0x3f;
 		break;
 
 	case CS7:
 		lData = UART_LCR_WLEN7;
-		mask = 0x7f;
 		break;
 	default:
 	case CS8:
@@ -1685,11 +1680,8 @@ static void mos7720_set_termios(struct tty_struct *tty,
 		struct usb_serial_port *port, struct ktermios *old_termios)
 {
 	int status;
-	struct usb_serial *serial;
 	struct moschip_port *mos7720_port;
 
-	serial = port->serial;
-
 	mos7720_port = usb_get_serial_port_data(port);
 
 	if (mos7720_port == NULL)

drivers/usb/serial/mos7840.c

@@ -805,18 +805,19 @@ static void mos7840_bulk_out_data_callback(struct urb *urb)
 	struct moschip_port *mos7840_port;
 	struct usb_serial_port *port;
 	int status = urb->status;
+	unsigned long flags;
 	int i;
 
 	mos7840_port = urb->context;
 	port = mos7840_port->port;
-	spin_lock(&mos7840_port->pool_lock);
+	spin_lock_irqsave(&mos7840_port->pool_lock, flags);
 	for (i = 0; i < NUM_URBS; i++) {
 		if (urb == mos7840_port->write_urb_pool[i]) {
 			mos7840_port->busy[i] = 0;
 			break;
 		}
 	}
-	spin_unlock(&mos7840_port->pool_lock);
+	spin_unlock_irqrestore(&mos7840_port->pool_lock, flags);
 
 	if (status) {
 		dev_dbg(&port->dev, "nonzero write bulk status received:%d\n", status);

drivers/usb/serial/quatech2.c

@@ -194,7 +194,7 @@ static inline int qt2_getregister(struct usb_device *dev,
 	ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
 			      QT_SET_GET_REGISTER, 0xc0, reg,
 			      uart, data, sizeof(*data), QT2_USB_TIMEOUT);
-	if (ret < sizeof(*data)) {
+	if (ret < (int)sizeof(*data)) {
 		if (ret >= 0)
 			ret = -EIO;
 	}
@@ -621,16 +621,17 @@ static void qt2_write_bulk_callback(struct urb *urb)
 {
 	struct usb_serial_port *port;
 	struct qt2_port_private *port_priv;
+	unsigned long flags;
 
 	port = urb->context;
 	port_priv = usb_get_serial_port_data(port);
 
-	spin_lock(&port_priv->urb_lock);
+	spin_lock_irqsave(&port_priv->urb_lock, flags);
 
 	port_priv->urb_in_use = false;
 	usb_serial_port_softint(port);
 
-	spin_unlock(&port_priv->urb_lock);
+	spin_unlock_irqrestore(&port_priv->urb_lock, flags);
 
 }
 

drivers/usb/serial/sierra.c

@@ -409,6 +409,7 @@ static void sierra_outdat_callback(struct urb *urb)
 	struct sierra_port_private *portdata = usb_get_serial_port_data(port);
 	struct sierra_intf_private *intfdata;
 	int status = urb->status;
+	unsigned long flags;
 
 	intfdata = usb_get_serial_data(port->serial);
 
@@ -419,12 +420,12 @@ static void sierra_outdat_callback(struct urb *urb)
 		dev_dbg(&port->dev, "%s - nonzero write bulk status "
 		    "received: %d\n", __func__, status);
 
-	spin_lock(&portdata->lock);
+	spin_lock_irqsave(&portdata->lock, flags);
 	--portdata->outstanding_urbs;
-	spin_unlock(&portdata->lock);
-	spin_lock(&intfdata->susp_lock);
+	spin_unlock_irqrestore(&portdata->lock, flags);
+	spin_lock_irqsave(&intfdata->susp_lock, flags);
 	--intfdata->in_flight;
-	spin_unlock(&intfdata->susp_lock);
+	spin_unlock_irqrestore(&intfdata->susp_lock, flags);
 
 	usb_serial_port_softint(port);
 }
@@ -770,9 +771,9 @@ static void sierra_close(struct usb_serial_port *port)
 		kfree(urb->transfer_buffer);
 		usb_free_urb(urb);
 		usb_autopm_put_interface_async(serial->interface);
-		spin_lock(&portdata->lock);
+		spin_lock_irq(&portdata->lock);
 		portdata->outstanding_urbs--;
-		spin_unlock(&portdata->lock);
+		spin_unlock_irq(&portdata->lock);
 	}
 
 	sierra_stop_rx_urbs(port);

drivers/usb/serial/ssu100.c

@@ -104,7 +104,7 @@ static inline int ssu100_getregister(struct usb_device *dev,
 	ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
 			      QT_SET_GET_REGISTER, 0xc0, reg,
 			      uart, data, sizeof(*data), 300);
-	if (ret < sizeof(*data)) {
+	if (ret < (int)sizeof(*data)) {
 		if (ret >= 0)
 			ret = -EIO;
 	}

drivers/usb/serial/symbolserial.c

@@ -35,6 +35,7 @@ static void symbol_int_callback(struct urb *urb)
 	struct symbol_private *priv = usb_get_serial_port_data(port);
 	unsigned char *data = urb->transfer_buffer;
 	int status = urb->status;
+	unsigned long flags;
 	int result;
 	int data_length;
 
@@ -73,7 +74,7 @@ static void symbol_int_callback(struct urb *urb)
 	}
 
 exit:
-	spin_lock(&priv->lock);
+	spin_lock_irqsave(&priv->lock, flags);
 
 	/* Continue trying to always read if we should */
 	if (!priv->throttled) {
@@ -84,7 +85,7 @@ exit:
 							__func__, result);
 	} else
 		priv->actually_throttled = true;
-	spin_unlock(&priv->lock);
+	spin_unlock_irqrestore(&priv->lock, flags);
 }
 
 static int symbol_open(struct tty_struct *tty, struct usb_serial_port *port)

drivers/usb/serial/ti_usb_3410_5052.c

@@ -1215,6 +1215,7 @@ static void ti_bulk_in_callback(struct urb *urb)
 	struct usb_serial_port *port = tport->tp_port;
 	struct device *dev = &urb->dev->dev;
 	int status = urb->status;
+	unsigned long flags;
 	int retval = 0;
 
 	switch (status) {
@@ -1247,20 +1248,20 @@ static void ti_bulk_in_callback(struct urb *urb)
 				__func__);
 		else
 			ti_recv(port, urb->transfer_buffer, urb->actual_length);
-		spin_lock(&tport->tp_lock);
+		spin_lock_irqsave(&tport->tp_lock, flags);
 		port->icount.rx += urb->actual_length;
-		spin_unlock(&tport->tp_lock);
+		spin_unlock_irqrestore(&tport->tp_lock, flags);
 	}
 
 exit:
 	/* continue to read unless stopping */
-	spin_lock(&tport->tp_lock);
+	spin_lock_irqsave(&tport->tp_lock, flags);
 	if (tport->tp_read_urb_state == TI_READ_URB_RUNNING)
 		retval = usb_submit_urb(urb, GFP_ATOMIC);
 	else if (tport->tp_read_urb_state == TI_READ_URB_STOPPING)
 		tport->tp_read_urb_state = TI_READ_URB_STOPPED;
 
-	spin_unlock(&tport->tp_lock);
+	spin_unlock_irqrestore(&tport->tp_lock, flags);
 	if (retval)
 		dev_err(dev, "%s - resubmit read urb failed, %d\n",
 			__func__, retval);

drivers/usb/serial/usb_wwan.c

@@ -326,6 +326,7 @@ static void usb_wwan_outdat_callback(struct urb *urb)
 	struct usb_serial_port *port;
 	struct usb_wwan_port_private *portdata;
 	struct usb_wwan_intf_private *intfdata;
+	unsigned long flags;
 	int i;
 
 	port = urb->context;
@@ -334,9 +335,9 @@ static void usb_wwan_outdat_callback(struct urb *urb)
 	usb_serial_port_softint(port);
 	usb_autopm_put_interface_async(port->serial->interface);
 	portdata = usb_get_serial_port_data(port);
-	spin_lock(&intfdata->susp_lock);
+	spin_lock_irqsave(&intfdata->susp_lock, flags);
 	intfdata->in_flight--;
-	spin_unlock(&intfdata->susp_lock);
+	spin_unlock_irqrestore(&intfdata->susp_lock, flags);
 
 	for (i = 0; i < N_OUT_URB; ++i) {
 		if (portdata->out_urbs[i] == urb) {